RMON2-MIB

File: RMON2-MIB.mib (211460 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-TC	SNMPv2-CONF
RFC1213-MIB	RMON-MIB	TOKEN-RING-RMON-MIB

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	Counter32
Integer32	Gauge32	IpAddress
TimeTicks	TEXTUAL-CONVENTION	RowStatus
DisplayString	TimeStamp	MODULE-COMPLIANCE
OBJECT-GROUP	mib-2	ifIndex
OwnerString	statistics	history
hosts	matrix	filter
etherStatsEntry	historyControlEntry	hostControlEntry
matrixControlEntry	filterEntry	channelEntry
tokenRing	tokenRingMLStatsEntry	tokenRingPStatsEntry
ringStationControlEntry	sourceRoutingStatsEntry

Defined Types

ZeroBasedCounter32
This TC describes an object which counts events with the following semantics: objects of this type will be set to zero(0) on creation and will thereafter count appropriate events, wrapping back to zero(0) when the value 2^32 is reached. Provided that an application discovers the new object within the minimum time to wrap it can use the initial value as a delta since it last polled the table of which this object is part. It is important for a management station to be aware of this minimum time and the actual time between polls, and to discard data if the actual time is too long or there is no defined minimum time. Typically this TC is used in tables where the INDEX space is constantly changing and/or the TimeFilter mechanism is in use.
TEXTUAL-CONVENTION
	Gauge32

LastCreateTime
This TC describes an object that stores the last time its entry was created. This can be used for polling applications to determine that an entry has been deleted and re-created between polls, causing an otherwise undetectable discontinuity in the data.
TEXTUAL-CONVENTION
	TimeStamp

TimeFilter
To be used for the index to a table. Allows an application to download only those rows changed since a particular time. A row is considered changed if the value of any object in the row changes or if the row is created or deleted. When sysUpTime is equal to zero, this table shall be empty. One entry exists for each past value of sysUpTime, except that the whole table is purged should sysUpTime wrap. As this basic row is updated new conceptual rows are created (which still share the now updated object values with all other instances). The number of instances which are created is determined by the value of sysUpTime at which the basic row was last updated. One instance will exist for each value of sysUpTime at the last update time for the row. A new timeMark instance is created for each new sysUpTime value. Each new conceptual row will be associated with the timeMark instance which was created at the value of sysUpTime with which the conceptual row is to be associated. By definition all conceptual rows were updated at or after time zero and so at least one conceptual row (associated with timeMark.0) must exist for each underlying (basic) row. See the appendix for further discussion of this variable. Consider the following fooTable: fooTable ... INDEX { fooTimeMark, fooIndex } FooEntry { fooTimeMark TimeFilter fooIndex INTEGER, fooCounts Counter } Should there be two basic rows in this table (fooIndex == 1, fooIndex == 2) and row 1 was updated most recently at time 6, while row 2 was updated most recently at time 8, and both rows had been updated on several earlier occasions such that the current values were 5 and 9 respectively then the following fooCounts instances would exist. fooCounts.0.1 5 fooCounts.0.2 9 fooCounts.1.1 5 fooCounts.1.2 9 fooCounts.2.1 5 fooCounts.2.2 9 fooCounts.3.1 5 fooCounts.3.2 9 fooCounts.4.1 5 fooCounts.4.2 9 fooCounts.5.1 5 fooCounts.5.2 9 fooCounts.6.1 5 fooCounts.6.2 9 fooCounts.7.2 9 -- note that row 1 doesn't exist for fooCounts.8.2 9 -- times 7 and 8
TEXTUAL-CONVENTION
	TimeTicks

DataSource
Identifies the source of the data that the associated function is configured to analyze. This source can be any interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in [3,5], for the desired interface. For example, if an entry were to receive data from interface #1, this object would be set to ifIndex.1.
TEXTUAL-CONVENTION
	OBJECT IDENTIFIER

ProtocolDirEntry
SEQUENCE
	protocolDirID	OCTET STRING
	protocolDirParameters	OCTET STRING
	protocolDirLocalIndex	Integer32
	protocolDirDescr	DisplayString
	protocolDirType	OCTET STRING
	protocolDirAddressMapConfig	INTEGER
	protocolDirHostConfig	INTEGER
	protocolDirMatrixConfig	INTEGER
	protocolDirOwner	OwnerString
	protocolDirStatus	RowStatus

ProtocolDistControlEntry
SEQUENCE
	protocolDistControlIndex	Integer32
	protocolDistControlDataSource	DataSource
	protocolDistControlDroppedFrames	Counter32
	protocolDistControlCreateTime	LastCreateTime
	protocolDistControlOwner	OwnerString
	protocolDistControlStatus	RowStatus

ProtocolDistStatsEntry
SEQUENCE
	protocolDistStatsPkts	ZeroBasedCounter32
	protocolDistStatsOctets	ZeroBasedCounter32

AddressMapControlEntry
SEQUENCE
	addressMapControlIndex	Integer32
	addressMapControlDataSource	DataSource
	addressMapControlDroppedFrames	Counter32
	addressMapControlOwner	OwnerString
	addressMapControlStatus	RowStatus

AddressMapEntry
SEQUENCE
	addressMapTimeMark	TimeFilter
	addressMapNetworkAddress	OCTET STRING
	addressMapSource	OBJECT IDENTIFIER
	addressMapPhysicalAddress	OCTET STRING
	addressMapLastChange	TimeStamp

HlHostControlEntry
SEQUENCE
	hlHostControlIndex	Integer32
	hlHostControlDataSource	DataSource
	hlHostControlNlDroppedFrames	Counter32
	hlHostControlNlInserts	Counter32
	hlHostControlNlDeletes	Counter32
	hlHostControlNlMaxDesiredEntries	Integer32
	hlHostControlAlDroppedFrames	Counter32
	hlHostControlAlInserts	Counter32
	hlHostControlAlDeletes	Counter32
	hlHostControlAlMaxDesiredEntries	Integer32
	hlHostControlOwner	OwnerString
	hlHostControlStatus	RowStatus

NlHostEntry
SEQUENCE
	nlHostTimeMark	TimeFilter
	nlHostAddress	OCTET STRING
	nlHostInPkts	ZeroBasedCounter32
	nlHostOutPkts	ZeroBasedCounter32
	nlHostInOctets	ZeroBasedCounter32
	nlHostOutOctets	ZeroBasedCounter32
	nlHostOutMacNonUnicastPkts	ZeroBasedCounter32
	nlHostCreateTime	LastCreateTime

HlMatrixControlEntry
SEQUENCE
	hlMatrixControlIndex	Integer32
	hlMatrixControlDataSource	DataSource
	hlMatrixControlNlDroppedFrames	Counter32
	hlMatrixControlNlInserts	Counter32
	hlMatrixControlNlDeletes	Counter32
	hlMatrixControlNlMaxDesiredEntries	Integer32
	hlMatrixControlAlDroppedFrames	Counter32
	hlMatrixControlAlInserts	Counter32
	hlMatrixControlAlDeletes	Counter32
	hlMatrixControlAlMaxDesiredEntries	Integer32
	hlMatrixControlOwner	OwnerString
	hlMatrixControlStatus	RowStatus

NlMatrixSDEntry
SEQUENCE
	nlMatrixSDTimeMark	TimeFilter
	nlMatrixSDSourceAddress	OCTET STRING
	nlMatrixSDDestAddress	OCTET STRING
	nlMatrixSDPkts	ZeroBasedCounter32
	nlMatrixSDOctets	ZeroBasedCounter32
	nlMatrixSDCreateTime	LastCreateTime

NlMatrixDSEntry
SEQUENCE
	nlMatrixDSTimeMark	TimeFilter
	nlMatrixDSSourceAddress	OCTET STRING
	nlMatrixDSDestAddress	OCTET STRING
	nlMatrixDSPkts	ZeroBasedCounter32
	nlMatrixDSOctets	ZeroBasedCounter32
	nlMatrixDSCreateTime	LastCreateTime

NlMatrixTopNControlEntry
SEQUENCE
	nlMatrixTopNControlIndex	Integer32
	nlMatrixTopNControlMatrixIndex	Integer32
	nlMatrixTopNControlRateBase	INTEGER
	nlMatrixTopNControlTimeRemaining	Integer32
	nlMatrixTopNControlGeneratedReports	Counter32
	nlMatrixTopNControlDuration	Integer32
	nlMatrixTopNControlRequestedSize	Integer32
	nlMatrixTopNControlGrantedSize	Integer32
	nlMatrixTopNControlStartTime	TimeStamp
	nlMatrixTopNControlOwner	OwnerString
	nlMatrixTopNControlStatus	RowStatus

NlMatrixTopNEntry
SEQUENCE
	nlMatrixTopNIndex	Integer32
	nlMatrixTopNProtocolDirLocalIndex	Integer32
	nlMatrixTopNSourceAddress	OCTET STRING
	nlMatrixTopNDestAddress	OCTET STRING
	nlMatrixTopNPktRate	Gauge32
	nlMatrixTopNReversePktRate	Gauge32
	nlMatrixTopNOctetRate	Gauge32
	nlMatrixTopNReverseOctetRate	Gauge32

AlHostEntry
SEQUENCE
	alHostTimeMark	TimeFilter
	alHostInPkts	ZeroBasedCounter32
	alHostOutPkts	ZeroBasedCounter32
	alHostInOctets	ZeroBasedCounter32
	alHostOutOctets	ZeroBasedCounter32
	alHostCreateTime	LastCreateTime

AlMatrixSDEntry
SEQUENCE
	alMatrixSDTimeMark	TimeFilter
	alMatrixSDPkts	ZeroBasedCounter32
	alMatrixSDOctets	ZeroBasedCounter32
	alMatrixSDCreateTime	LastCreateTime

AlMatrixDSEntry
SEQUENCE
	alMatrixDSTimeMark	TimeFilter
	alMatrixDSPkts	ZeroBasedCounter32
	alMatrixDSOctets	ZeroBasedCounter32
	alMatrixDSCreateTime	LastCreateTime

AlMatrixTopNControlEntry
SEQUENCE
	alMatrixTopNControlIndex	Integer32
	alMatrixTopNControlMatrixIndex	Integer32
	alMatrixTopNControlRateBase	INTEGER
	alMatrixTopNControlTimeRemaining	Integer32
	alMatrixTopNControlGeneratedReports	Counter32
	alMatrixTopNControlDuration	Integer32
	alMatrixTopNControlRequestedSize	Integer32
	alMatrixTopNControlGrantedSize	Integer32
	alMatrixTopNControlStartTime	TimeStamp
	alMatrixTopNControlOwner	OwnerString
	alMatrixTopNControlStatus	RowStatus

AlMatrixTopNEntry
SEQUENCE
	alMatrixTopNIndex	Integer32
	alMatrixTopNProtocolDirLocalIndex	Integer32
	alMatrixTopNSourceAddress	OCTET STRING
	alMatrixTopNDestAddress	OCTET STRING
	alMatrixTopNAppProtocolDirLocalIndex	Integer32
	alMatrixTopNPktRate	Gauge32
	alMatrixTopNReversePktRate	Gauge32
	alMatrixTopNOctetRate	Gauge32
	alMatrixTopNReverseOctetRate	Gauge32

UsrHistoryControlEntry
SEQUENCE
	usrHistoryControlIndex	Integer32
	usrHistoryControlObjects	Integer32
	usrHistoryControlBucketsRequested	Integer32
	usrHistoryControlBucketsGranted	Integer32
	usrHistoryControlInterval	Integer32
	usrHistoryControlOwner	OwnerString
	usrHistoryControlStatus	RowStatus

UsrHistoryObjectEntry
SEQUENCE
	usrHistoryObjectIndex	Integer32
	usrHistoryObjectVariable	OBJECT IDENTIFIER
	usrHistoryObjectSampleType	INTEGER

UsrHistoryEntry
SEQUENCE
	usrHistorySampleIndex	Integer32
	usrHistoryIntervalStart	TimeStamp
	usrHistoryIntervalEnd	TimeStamp
	usrHistoryAbsValue	Gauge32
	usrHistoryValStatus	INTEGER

ControlString
This data type is used to communicate with a modem or a serial data switch. A ControlString contains embedded commands to control how the device will interact with the remote device through the serial interface. Commands are represented as two character sequences beginning with the `^' character. The following commands are recognized by the device (note that command characters are case sensitive): ^s Send string that follows which is terminated by the next command or the end of string. ^c Delay for the number of seconds that follows. Toss out any data received rather than storing it in a buffer for parsing. ^t Set timeout to the value represented by the decimal digits that follow. The default timeout is 20 seconds. Note that this timeout may be overridden by a smaller serialTimeout configured for the associated serial interface (see serialConfigTable). ^w Wait for the reply string that follows which is terminated by the next command or the end of string. Partial and case insensitive matching is applied, ie. if the reply string (any case combination) is found anywhere in the received string, then the a match is found. If the current timeout elapses without a match, then the remaining control string is ignored. ^! The ^ character. ^d Delay the number of seconds specified by the decimal digits that follow. ^b Send break for the number of milliseconds specified by the decimal digits that follow. If no digits follow, break will be enforced for 250 milliseconds by default. The following ASCII control characters may be inserted into the `^s' send string or the `^w' reply string: ^@ 0x00 ^A 0x01 .. ^M 0x0D .. ^Z 0x1A ^[ 0x1B ^ 0x1C ^] 0x1D ^^ 0x1E ^_ 0x1F Binary data may also be inserted into the data stream. The control sequence for each byte of binary data is ^0x##, where ## is the hexadecimal representation of the data byte. Two ASCII characters (0-9, a-f, A-F) must follow the `^0x' control prefix. For example, `^0x0D^0x0A' is interpreted as a carriage return followed by a line feed.
TEXTUAL-CONVENTION
	DisplayString

SerialConfigEntry
SEQUENCE
	serialMode	INTEGER
	serialProtocol	INTEGER
	serialTimeout	Integer32	1..65535
	serialModemInitString	ControlString	Size(0..255)
	serialModemHangUpString	ControlString	Size(0..255)
	serialModemConnectResp	DisplayString	Size(0..255)
	serialModemNoConnectResp	DisplayString	Size(0..255)
	serialDialoutTimeout	Integer32	1..65535
	serialStatus	RowStatus

NetConfigEntry
SEQUENCE
	netConfigIPAddress	IpAddress
	netConfigSubnetMask	IpAddress
	netConfigStatus	RowStatus

TrapDestEntry
SEQUENCE
	trapDestIndex	Integer32
	trapDestCommunity	OCTET STRING
	trapDestProtocol	INTEGER
	trapDestAddress	OCTET STRING
	trapDestOwner	OwnerString
	trapDestStatus	RowStatus

SerialConnectionEntry
SEQUENCE
	serialConnectIndex	Integer32
	serialConnectDestIpAddress	IpAddress
	serialConnectType	INTEGER
	serialConnectDialString	ControlString
	serialConnectSwitchConnectSeq	ControlString
	serialConnectSwitchDisconnectSeq	ControlString
	serialConnectSwitchResetSeq	ControlString
	serialConnectOwner	OwnerString
	serialConnectStatus	RowStatus

EtherStats2Entry
SEQUENCE
	etherStatsDroppedFrames	Counter32
	etherStatsCreateTime	LastCreateTime

HistoryControl2Entry
SEQUENCE
	historyControlDroppedFrames	Counter32

HostControl2Entry
SEQUENCE
	hostControlDroppedFrames	Counter32
	hostControlCreateTime	LastCreateTime

MatrixControl2Entry
SEQUENCE
	matrixControlDroppedFrames	Counter32
	matrixControlCreateTime	LastCreateTime

Channel2Entry
SEQUENCE
	channelDroppedFrames	Counter32
	channelCreateTime	LastCreateTime

TokenRingMLStats2Entry
SEQUENCE
	tokenRingMLStatsDroppedFrames	Counter32
	tokenRingMLStatsCreateTime	LastCreateTime

TokenRingPStats2Entry
SEQUENCE
	tokenRingPStatsDroppedFrames	Counter32
	tokenRingPStatsCreateTime	LastCreateTime

RingStationControl2Entry
SEQUENCE
	ringStationControlDroppedFrames	Counter32
	ringStationControlCreateTime	LastCreateTime

SourceRoutingStats2Entry
SEQUENCE
	sourceRoutingStatsDroppedFrames	Counter32
	sourceRoutingStatsCreateTime	LastCreateTime

Filter2Entry
SEQUENCE
	filterProtocolDirDataLocalIndex	Integer32
	filterProtocolDirLocalIndex	Integer32

Defined Values

rmon		1.3.6.1.2.1.16
The MIB module for managing remote monitoring device implementations. This MIB module augments the original RMON MIB as specified in RFC 1757.
MODULE-IDENTITY

protocolDir		1.3.6.1.2.1.16.11
OBJECT IDENTIFIER

protocolDist		1.3.6.1.2.1.16.12
OBJECT IDENTIFIER

addressMap		1.3.6.1.2.1.16.13
OBJECT IDENTIFIER

nlHost		1.3.6.1.2.1.16.14
OBJECT IDENTIFIER

nlMatrix		1.3.6.1.2.1.16.15
OBJECT IDENTIFIER

alHost		1.3.6.1.2.1.16.16
OBJECT IDENTIFIER

alMatrix		1.3.6.1.2.1.16.17
OBJECT IDENTIFIER

usrHistory		1.3.6.1.2.1.16.18
OBJECT IDENTIFIER

probeConfig		1.3.6.1.2.1.16.19
OBJECT IDENTIFIER

rmonConformance		1.3.6.1.2.1.16.20
OBJECT IDENTIFIER

protocolDirLastChange		1.3.6.1.2.1.16.11.1
The value of sysUpTime at the time the protocol directory was last modified, either through insertions or deletions, or through modifications of either the protocolDirAddressMapConfig, protocolDirHostConfig, or protocolDirMatrixConfig.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

protocolDirTable		1.3.6.1.2.1.16.11.2
This table lists the protocols that this agent has the capability to decode and count. There is one entry in this table for each such protocol. These protocols represent different network layer, transport layer, and higher-layer protocols. The agent should boot up with this table preconfigured with those protocols that it knows about and wishes to monitor. Implementations are strongly encouraged to support protocols higher than the network layer (at least for the protocol distribution group), even for implementations that don't support the application layer groups.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ProtocolDirEntry

protocolDirEntry		1.3.6.1.2.1.16.11.2.1
A conceptual row in the protocolDirTable. An example of the indexing of this entry is protocolDirLocalIndex.8.0.0.0.1.0.0.8.0.2.0.0, which is the encoding of a length of 8, followed by 8 subids encoding the protocolDirID of 1.2048, followed by a length of 2 and the 2 subids encoding zero-valued parameters.
Status: current	Access: not-accessible
OBJECT-TYPE
	ProtocolDirEntry

protocolDirID		1.3.6.1.2.1.16.11.2.1.1
A unique identifier for a particular protocol. Standard identifiers will be defined in a manner such that they can often be used as specifications for new protocols - i.e. a tree-structured assignment mechanism that matches the protocol encapsulation `tree' and which has algorithmic assignment mechanisms for certain subtrees. See RFC XXX for more details. Despite the algorithmic mechanism, the probe will only place entries in here for those protocols it chooses to collect. In other words, it need not populate this table with all of the possible ethernet protocol types, nor need it create them on the fly when it sees them. Whether or not it does these things is a matter of product definition (cost/benefit, usability), and is up to the designer of the product. If an entry is written to this table with a protocolDirID that the agent doesn't understand, either directly or algorithmically, the SET request will be rejected with an inconsistentName or badValue (for SNMPv1) error.
Status: current	Access: not-accessible
OBJECT-TYPE
	OCTET STRING

protocolDirParameters		1.3.6.1.2.1.16.11.2.1.2
A set of parameters for the associated protocolDirID. See the associated RMON2 Protocol Identifiers document for a description of the possible parameters. There will be one octet in this string for each sub-identifier in the protocolDirID, and the parameters will appear here in the same order as the associated sub-identifiers appear in the protocolDirID. Every node in the protocolDirID tree has a different, optional set of parameters defined (that is, the definition of parameters for a node is optional). The proper parameter value for each node is included in this string. Note that the inclusion of a parameter value in this string for each node is not optional - what is optional is that a node may have no parameters defined, in which case the parameter field for that node will be zero.
Status: current	Access: not-accessible
OBJECT-TYPE
	OCTET STRING

protocolDirLocalIndex		1.3.6.1.2.1.16.11.2.1.3
The locally arbitrary, but unique identifier associated with this protocolDir entry. The value for each supported protocol must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization, except that if a protocol is deleted and re-created, it must be re-created with a new value that has not been used since the last re-initialization. The specific value is meaningful only within a given SNMP entity. A protocolDirLocalIndex must not be re-used until the next agent-restart in the event the protocol directory entry is deleted.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..2147483647

protocolDirDescr		1.3.6.1.2.1.16.11.2.1.4
A textual description of the protocol encapsulation. A probe may choose to describe only a subset of the entire encapsulation (e.g. only the highest layer). This object is intended for human consumption only. This object may not be modified if the associated protocolDirStatus object is equal to active(1).
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(1..64)

protocolDirType		1.3.6.1.2.1.16.11.2.1.5
This object describes 2 attributes of this protocol directory entry. The presence or absence of the `extensible' bit describes whether or not this protocol directory entry can be extended by the user by creating protocol directory entries which are children of this protocol. An example of an entry that will often allow extensibility is `ip.udp'. The probe may automatically populate some children of this node such as `ip.udp.snmp' and `ip.udp.dns'. A probe administrator or user may also populate additional children via remote SNMP requests that create entries in this table. When a child node is added for a protocol for which the probe has no built in support, extending a parent node (for which the probe does have built in support), that child node is not extendible. This is termed `limited extensibility'. When a child node is added through this extensibility mechanism, the values of protocolDirLocalIndex and protocolDirType shall be assigned by the agent. The other objects in the entry will be assigned by the manager who is creating the new entry. This object also describes whether or not this agent can recognize addresses for this protocol, should it be a network level protocol. That is, while a probe may be able to recognize packets of a particular network layer protocol and count them, it takes additional logic to be able to recognize the addresses in this protocol and to populate network layer or application layer tables with the addresses in this protocol. If this bit is set, the agent will recognize network layer addresses for this protoocl and populate the network and application layer host and matrix tables with these protocols. Note that when an entry is created, the agent will supply values for the bits that match the capabilities of the agent with respect to this protocol. Note that since row creations usually exercise the limited extensibility feature, these bits will usually be set to zero.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(1)

protocolDirAddressMapConfig		1.3.6.1.2.1.16.11.2.1.6
This object describes and configures the probe's support for address mapping for this protocol. When the probe creates entries in this table for all protocols that it understands, it will set the entry to notSupported(1) if it doesn't have the capability to perform address mapping for the protocol or if this protocol is not a network-layer protocol. When an entry is created in this table by a management operation as part of the limited extensibility feature, the probe must set this value to notSupported(1), because limited extensibility of the protocolDirTable does not extend to interpreting addresses of the extended protocols. If the value of this object is notSupported(1), the probe will not perform address mapping for this protocol and shall not allow this object to be changed to any other value. If the value of this object is supportedOn(3), the probe supports address mapping for this protocol and is configured to perform address mapping for this protocol for all addressMappingControlEntries and all interfaces. If the value of this object is supportedOff(2), the probe supports address mapping for this protocol but is configured to not perform address mapping for this protocol for any addressMappingControlEntries and all interfaces. Whenever this value changes from supportedOn(3) to supportedOff(2), the probe shall delete all related entries in the addressMappingTable.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notSupported(1), supportedOff(2), supportedOn(3)

protocolDirHostConfig		1.3.6.1.2.1.16.11.2.1.7
This object describes and configures the probe's support for the network layer and application layer host tables for this protocol. When the probe creates entries in this table for all protocols that it understands, it will set the entry to notSupported(1) if it doesn't have the capability to track the nlHostTable for this protocol or if the alHostTable is implemented but doesn't have the capability to track this protocol. Note that if the alHostTable is implemented, the probe may only support a protocol if it is supported in both the nlHostTable and the alHostTable. If the associated protocolDirType object has the addressRecognitionCapable bit set, then this is a network layer protocol for which the probe recognizes addresses, and thus the probe will populate the nlHostTable and alHostTable with addresses it discovers for this protocol. If the value of this object is notSupported(1), the probe will not track the nlHostTable or alHostTable for this protocol and shall not allow this object to be changed to any other value. If the value of this object is supportedOn(3), the probe supports tracking of the nlHostTable and alHostTable for this protocol and is configured to track both tables for this protocol for all control entries and all interfaces. If the value of this object is supportedOff(2), the probe supports tracking of the nlHostTable and alHostTable for this protocol but is configured to not track these tables for any control entries or interfaces. Whenever this value changes from supportedOn(3) to supportedOff(2), the probe shall delete all related entries in the nlHostTable and alHostTable. Note that since each alHostEntry references 2 protocol directory entries, one for the network address and one for the type of the highest protocol recognized, that an entry will only be created in that table if this value is supportedOn(3) for both protocols.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notSupported(1), supportedOff(2), supportedOn(3)

protocolDirMatrixConfig		1.3.6.1.2.1.16.11.2.1.8
This object describes and configures the probe's support for the network layer and application layer matrix tables for this protocol. When the probe creates entries in this table for all protocols that it understands, it will set the entry to notSupported(1) if it doesn't have the capability to track the nlMatrixTables for this protocol or if the alMatrixTables are implemented but don't have the capability to track this protocol. Note that if the alMatrix tables are implemented, the probe may only support a protocol if it is supported in the the both of the nlMatrixTables and both of the alMatrixTables. If the associated protocolDirType object has the addressRecognitionCapable bit set, then this is a network layer protocol for which the probe recognizes addresses, and thus the probe will populate both of the nlMatrixTables and both of the alMatrixTables with addresses it discovers for this protocol. If the value of this object is notSupported(1), the probe will not track either of the nlMatrixTables or the alMatrixTables for this protocol and shall not allow this object to be changed to any other value. If the value of this object is supportedOn(3), the probe supports tracking of both of the nlMatrixTables and (if implemented) both of the alMatrixTables for this protocol and is configured to track these tables for this protocol for all control entries and all interfaces. If the value of this object is supportedOff(2), the probe supports tracking of both of the nlMatrixTables and (if implemented) both of the alMatrixTables for this protocol but is configured to not track these tables for this protocol for any control entries or interfaces. Whenever this value changes from supportedOn(3) to supportedOff(2), the probe shall delete all related entries in the nlMatrixTables and the alMatrixTables. Note that since each alMatrixEntry references 2 protocol directory entries, one for the network address and one for the type of the highest protocol recognized, that an entry will only be created in that table if this value is supportedOn(3) for both protocols.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notSupported(1), supportedOff(2), supportedOn(3)

protocolDirOwner		1.3.6.1.2.1.16.11.2.1.9
The entity that configured this entry and is therefore using the resources assigned to it.
Status: current	Access: read-create
OBJECT-TYPE
	OwnerString

protocolDirStatus		1.3.6.1.2.1.16.11.2.1.10
The status of this protocol directory entry. An entry may not exist in the active state unless all objects in the entry have an appropriate value. If this object is not equal to active(1), all associated entries in the nlHostTable, nlMatrixSDTable, nlMatrixDSTable, alHostTable, alMatrixSDTable, and alMatrixDSTable shall be deleted.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

protocolDistControlTable		1.3.6.1.2.1.16.12.1
Controls the setup of protocol type distribution statistics tables. Implementations are encouraged to add an entry per monitored interface upon initialization so that a default collection of protocol statistics is available. Rationale: This table controls collection of very basic statistics for any or all of the protocols detected on a given interface. An NMS can use this table to quickly determine bandwidth allocation utilized by different protocols. A media-specific statistics collection could also be configured (e.g. etherStats, trPStats) to easily obtain total frame, octet, and droppedEvents for the same interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ProtocolDistControlEntry

protocolDistControlEntry		1.3.6.1.2.1.16.12.1.1
A conceptual row in the protocolDistControlTable. An example of the indexing of this entry is protocolDistControlDroppedFrames.7
Status: current	Access: not-accessible
OBJECT-TYPE
	ProtocolDistControlEntry

protocolDistControlIndex		1.3.6.1.2.1.16.12.1.1.1
A unique index for this protocolDistControlEntry.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..65535

protocolDistControlDataSource		1.3.6.1.2.1.16.12.1.1.2
The source of data for the this protocol distribution. The statistics in this group reflect all packets on the local network segment attached to the identified interface. This object may not be modified if the associated protocolDistControlStatus object is equal to active(1).
Status: current	Access: read-create
OBJECT-TYPE
	DataSource

protocolDistControlDroppedFrames		1.3.6.1.2.1.16.12.1.1.3
The total number of frames which were received by the probe and therefore not accounted for in the *StatsDropEvents, but for which the probe chose not to count for this entry for whatever reason. Most often, this event occurs when the probe is out of some resources and decides to shed load from this collection. This count does not include packets that were not counted because they had MAC-layer errors. Note that, unlike the dropEvents counter, this number is the exact number of frames dropped.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

protocolDistControlCreateTime		1.3.6.1.2.1.16.12.1.1.4
The value of sysUpTime when this control entry was last activated. This can be used by the management station to ensure that the table has not been deleted and recreated between polls.
Status: current	Access: read-only
OBJECT-TYPE
	LastCreateTime

protocolDistControlOwner		1.3.6.1.2.1.16.12.1.1.5
The entity that configured this entry and is therefore using the resources assigned to it.
Status: current	Access: read-create
OBJECT-TYPE
	OwnerString

protocolDistControlStatus		1.3.6.1.2.1.16.12.1.1.6
The status of this row. An entry may not exist in the active state unless all objects in the entry have an appropriate value. If this object is not equal to active(1), all associated entries in the protocolDistStatsTable shall be deleted.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

protocolDistStatsTable		1.3.6.1.2.1.16.12.2
An entry is made in this table for every protocol in the protocolDirTable which has been seen in at least one packet. Counters are updated in this table for every protocol type that is encountered when parsing a packet, but no counters are updated for packets with MAC-layer errors. Note that if a protocolDirEntry is deleted, all associated entries in this table are removed.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ProtocolDistStatsEntry

protocolDistStatsEntry		1.3.6.1.2.1.16.12.2.1
A conceptual row in the protocolDistStatsTable. The index is composed of the protocolDistControlIndex of the associated protocolDistControlEntry followed by the protocolDirLocalIndex of the associated protocol that this entry represents. In other words, the index identifies the protocol distribution an entry is a part of as well as the particular protocol that it represents. An example of the indexing of this entry is protocolDistStatsPkts.1.18
Status: current	Access: not-accessible
OBJECT-TYPE
	ProtocolDistStatsEntry

protocolDistStatsPkts		1.3.6.1.2.1.16.12.2.1.1
The number of packets without errors received of this protocol type. Note that this is the number of link-layer packets, so if a single network-layer packet is fragmented into several link-layer frames, this counter is incremented several times.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

protocolDistStatsOctets		1.3.6.1.2.1.16.12.2.1.2
The number of octets in packets received of this protocol type since it was added to the protocolDistStatsTable (excluding framing bits but including FCS octets), except for those octets in packets that contained errors. Note this doesn't count just those octets in the particular protocol frames, but includes the entire packet that contained the protocol.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

addressMapInserts		1.3.6.1.2.1.16.13.1
The number of times an address mapping entry has been inserted into the addressMapTable. If an entry is inserted, then deleted, and then inserted, this counter will be incremented by 2. Note that the table size can be determined by subtracting addressMapDeletes from addressMapInserts.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

addressMapDeletes		1.3.6.1.2.1.16.13.2
The number of times an address mapping entry has been deleted from the addressMapTable (for any reason). If an entry is deleted, then inserted, and then deleted, this counter will be incremented by 2. Note that the table size can be determined by subtracting addressMapDeletes from addressMapInserts.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

addressMapMaxDesiredEntries		1.3.6.1.2.1.16.13.3
The maximum number of entries that are desired in the addressMapTable. The probe will not create more than this number of entries in the table, but may choose to create fewer entries in this table for any reason including the lack of resources. If this object is set to a value less than the current number of entries, enough entries are chosen in an implementation-dependent manner and deleted so that the number of entries in the table equals the value of this object. If this value is set to -1, the probe may create any number of entries in this table. This object may be used to control how resources are allocated on the probe for the various RMON functions.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..2147483647

addressMapControlTable		1.3.6.1.2.1.16.13.4
A table to control the collection of network layer address to physical address to interface mappings. Note that this is not like the typical RMON controlTable and dataTable in which each entry creates its own data table. Each entry in this table enables the discovery of addresses on a new interface and the placement of address mappings into the central addressMapTable. Implementations are encouraged to add an entry per monitored interface upon initialization so that a default collection of address mappings is available.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AddressMapControlEntry

addressMapControlEntry		1.3.6.1.2.1.16.13.4.1
A conceptual row in the addressMapControlTable. An example of the indexing of this entry is addressMapControlDroppedFrames.1
Status: current	Access: not-accessible
OBJECT-TYPE
	AddressMapControlEntry

addressMapControlIndex		1.3.6.1.2.1.16.13.4.1.1
A unique index for this entry in the addressMapControlTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..65535

addressMapControlDataSource		1.3.6.1.2.1.16.13.4.1.2
The source of data for this addressMapControlEntry.
Status: current	Access: read-create
OBJECT-TYPE
	DataSource

addressMapControlDroppedFrames		1.3.6.1.2.1.16.13.4.1.3
The total number of frames which were received by the probe and therefore not accounted for in the *StatsDropEvents, but for which the probe chose not to count for this entry for whatever reason. Most often, this event occurs when the probe is out of some resources and decides to shed load from this collection. This count does not include packets that were not counted because they had MAC-layer errors. Note that, unlike the dropEvents counter, this number is the exact number of frames dropped.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

addressMapControlOwner		1.3.6.1.2.1.16.13.4.1.4
The entity that configured this entry and is therefore using the resources assigned to it.
Status: current	Access: read-create
OBJECT-TYPE
	OwnerString

addressMapControlStatus		1.3.6.1.2.1.16.13.4.1.5
The status of this addressMap control entry. An entry may not exist in the active state unless all objects in the entry have an appropriate value. If this object is not equal to active(1), all associated entries in the addressMapTable shall be deleted.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

addressMapTable		1.3.6.1.2.1.16.13.5
A table of network layer address to physical address to interface mappings. The probe will add entries to this table based on the source MAC and network addresses seen in packets without MAC-level errors. The probe will populate this table for all protocols in the protocol directory table whose value of protocolDirAddressMapConfig is equal to supportedOn(3), and will delete any entries whose protocolDirEntry is deleted or has a protocolDirAddressMapConfig value of supportedOff(2).
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AddressMapEntry

addressMapEntry		1.3.6.1.2.1.16.13.5.1
A conceptual row in the addressMapTable. The protocolDirLocalIndex in the index identifies the network layer protocol of the addressMapNetworkAddress. An example of the indexing of this entry is addressMapSource.783495.18.4.128.2.6.6.11.1.3.6.1.2.1.2.2.1.1.1
Status: current	Access: not-accessible
OBJECT-TYPE
	AddressMapEntry

addressMapTimeMark		1.3.6.1.2.1.16.13.5.1.1
A TimeFilter for this entry. See the TimeFilter textual convention to see how this works.
Status: current	Access: not-accessible
OBJECT-TYPE
	TimeFilter

addressMapNetworkAddress		1.3.6.1.2.1.16.13.5.1.2
The network address for this relation. This is represented as an octet string with specific semantics and length as identified by the protocolDirLocalIndex component of the index. For example, if the protocolDirLocalIndex indicates an encapsulation of ip, this object is encoded as a length octet of 4, followed by the 4 octets of the ip address, in network byte order.
Status: current	Access: not-accessible
OBJECT-TYPE
	OCTET STRING

addressMapSource		1.3.6.1.2.1.16.13.5.1.3
The interface or port on which the associated network address was most recently seen. If this address mapping was discovered on an interface, this object shall identify the instance of the ifIndex object, defined in [3,5], for the desired interface. For example, if an entry were to receive data from interface #1, this object would be set to ifIndex.1. If this address mapping was discovered on a port, this object shall identify the instance of the rptrGroupPortIndex object, defined in [RFC1516], for the desired port. For example, if an entry were to receive data from group #1, port #1, this object would be set to rptrGroupPortIndex.1.1. Note that while the dataSource associated with this entry may only point to index objects, this object may at times point to repeater port objects. This situation occurs when the dataSource points to an interface which is a locally attached repeater and the agent has additional information about the source port of traffic seen on that repeater.
Status: current	Access: not-accessible
OBJECT-TYPE
	OBJECT IDENTIFIER

addressMapPhysicalAddress		1.3.6.1.2.1.16.13.5.1.4
The last source physical address on which the associated network address was seen. If the protocol of the associated network address was encapsulated inside of a network-level or higher protocol, this will be the address of the next-lower protocol with the addressRecognitionCapable bit enabled and will be formatted as specified for that protocol.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

addressMapLastChange		1.3.6.1.2.1.16.13.5.1.5
The value of sysUpTime at the time this entry was last created or the values of the physical address changed. This can be used to help detect duplicate address problems, in which case this object will be updated frequently.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

hlHostControlTable		1.3.6.1.2.1.16.14.1
A list of higher layer (i.e. non-MAC) host table control entries. These entries will enable the collection of the network and application level host tables indexed by network addresses. Both the network and application level host tables are controlled by this table is so that they will both be created and deleted at the same time, further increasing the ease with which they can be implemented as a single datastore (note that if an implementation stores application layer host records in memory, it can derive network layer host records from them). Entries in the nlHostTable will be created on behalf of each entry in this table. Additionally, if this probe implements the alHostTable, entries in the alHostTable will be created on behalf of each entry in this table. Implementations are encouraged to add an entry per monitored interface upon initialization so that a default collection of host statistics is available.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HlHostControlEntry

hlHostControlEntry		1.3.6.1.2.1.16.14.1.1
A conceptual row in the hlHostControlTable. An example of the indexing of this entry is hlHostControlNlDroppedFrames.1
Status: current	Access: not-accessible
OBJECT-TYPE
	HlHostControlEntry

hlHostControlIndex		1.3.6.1.2.1.16.14.1.1.1
An index that uniquely identifies an entry in the hlHostControlTable. Each such entry defines a function that discovers hosts on a particular interface and places statistics about them in the nlHostTable, and optionally in the alHostTable, on behalf of this hlHostControlEntry.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..65535

hlHostControlDataSource		1.3.6.1.2.1.16.14.1.1.2
The source of data for the associated host tables. The statistics in this group reflect all packets on the local network segment attached to the identified interface. This object may not be modified if the associated hlHostControlStatus object is equal to active(1).
Status: current	Access: read-create
OBJECT-TYPE
	DataSource

hlHostControlNlDroppedFrames		1.3.6.1.2.1.16.14.1.1.3
The total number of frames which were received by the probe and therefore not accounted for in the *StatsDropEvents, but for which the probe chose not to count for the associated nlHost entries for whatever reason. Most often, this event occurs when the probe is out of some resources and decides to shed load from this collection. This count does not include packets that were not counted because they had MAC-layer errors. Note that if the nlHostTable is inactive because no protocols are enabled in the protocol directory, this value should be 0. Note that, unlike the dropEvents counter, this number is the exact number of frames dropped.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hlHostControlNlInserts		1.3.6.1.2.1.16.14.1.1.4
The number of times an nlHost entry has been inserted into the nlHost table. If an entry is inserted, then deleted, and then inserted, this counter will be incremented by 2. To allow for efficient implementation strategies, agents may delay updating this object for short periods of time. For example, an implementation strategy may allow internal data structures to differ from those visible via SNMP for short periods of time. This counter may reflect the internal data structures for those short periods of time. Note that the table size can be determined by subtracting hlHostControlNlDeletes from hlHostControlNlInserts.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hlHostControlNlDeletes		1.3.6.1.2.1.16.14.1.1.5
The number of times an nlHost entry has been deleted from the nlHost table (for any reason). If an entry is deleted, then inserted, and then deleted, this counter will be incremented by 2. To allow for efficient implementation strategies, agents may delay updating this object for short periods of time. For example, an implementation strategy may allow internal data structures to differ from those visible via SNMP for short periods of time. This counter may reflect the internal data structures for those short periods of time. Note that the table size can be determined by subtracting hlHostControlNlDeletes from hlHostControlNlInserts.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hlHostControlNlMaxDesiredEntries		1.3.6.1.2.1.16.14.1.1.6
The maximum number of entries that are desired in the nlHostTable on behalf of this control entry. The probe will not create more than this number of associated entries in the table, but may choose to create fewer entries in this table for any reason including the lack of resources. If this object is set to a value less than the current number of entries, enough entries are chosen in an implementation-dependent manner and deleted so that the number of entries in the table equals the value of this object. If this value is set to -1, the probe may create any number of entries in this table. If the associated hlHostControlStatus object is equal to `active', this object may not be modified. This object may be used to control how resources are allocated on the probe for the various RMON functions.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	-1..2147483647

hlHostControlAlDroppedFrames		1.3.6.1.2.1.16.14.1.1.7
The total number of frames which were received by the probe and therefore not accounted for in the *StatsDropEvents, but for which the probe chose not to count for the associated alHost entries for whatever reason. Most often, this event occurs when the probe is out of some resources and decides to shed load from this collection. This count does not include packets that were not counted because they had MAC-layer errors. Note that if the alHostTable is not implemented or is inactive because no protocols are enabled in the protocol directory, this value should be 0. Note that, unlike the dropEvents counter, this number is the exact number of frames dropped.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hlHostControlAlInserts		1.3.6.1.2.1.16.14.1.1.8
The number of times an alHost entry has been inserted into the alHost table. If an entry is inserted, then deleted, and then inserted, this counter will be incremented by 2. To allow for efficient implementation strategies, agents may delay updating this object for short periods of time. For example, an implementation strategy may allow internal data structures to differ from those visible via SNMP for short periods of time. This counter may reflect the internal data structures for those short periods of time. Note that the table size can be determined by subtracting hlHostControlAlDeletes from hlHostControlAlInserts.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hlHostControlAlDeletes		1.3.6.1.2.1.16.14.1.1.9
The number of times an alHost entry has been deleted from the alHost table (for any reason). If an entry is deleted, then inserted, and then deleted, this counter will be incremented by 2. To allow for efficient implementation strategies, agents may delay updating this object for short periods of time. For example, an implementation strategy may allow internal data structures to differ from those visible via SNMP for short periods of time. This counter may reflect the internal data structures for those short periods of time. Note that the table size can be determined by subtracting hlHostControlAlDeletes from hlHostControlAlInserts.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hlHostControlAlMaxDesiredEntries		1.3.6.1.2.1.16.14.1.1.10
The maximum number of entries that are desired in the alHost table on behalf of this control entry. The probe will not create more than this number of associated entries in the table, but may choose to create fewer entries in this table for any reason including the lack of resources. If this object is set to a value less than the current number of entries, enough entries are chosen in an implementation-dependent manner and deleted so that the number of entries in the table equals the value of this object. If this value is set to -1, the probe may create any number of entries in this table. If the associated hlHostControlStatus object is equal to `active', this object may not be modified. This object may be used to control how resources are allocated on the probe for the various RMON functions.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	-1..2147483647

hlHostControlOwner		1.3.6.1.2.1.16.14.1.1.11
The entity that configured this entry and is therefore using the resources assigned to it.
Status: current	Access: read-create
OBJECT-TYPE
	OwnerString

hlHostControlStatus		1.3.6.1.2.1.16.14.1.1.12
The status of this hlHostControlEntry. An entry may not exist in the active state unless all objects in the entry have an appropriate value. If this object is not equal to active(1), all associated entries in the nlHostTable and alHostTable shall be deleted.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

nlHostTable		1.3.6.1.2.1.16.14.2
A collection of statistics for a particular network layer address that has been discovered on an interface of this device. The probe will populate this table for all network layer protocols in the protocol directory table whose value of protocolDirHostConfig is equal to supportedOn(3), and will delete any entries whose protocolDirEntry is deleted or has a protocolDirHostConfig value of supportedOff(2). The probe will add to this table all addresses seen as the source or destination address in all packets with no MAC errors, and will increment octet and packet counts in the table for all packets with no MAC errors.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		NlHostEntry

nlHostEntry		1.3.6.1.2.1.16.14.2.1
A conceptual row in the nlHostTable. The hlHostControlIndex value in the index identifies the hlHostControlEntry on whose behalf this entry was created. The protocolDirLocalIndex value in the index identifies the network layer protocol of the nlHostAddress. An example of the indexing of this entry is nlHostOutPkts.1.783495.18.4.128.2.6.6.
Status: current	Access: not-accessible
OBJECT-TYPE
	NlHostEntry

nlHostTimeMark		1.3.6.1.2.1.16.14.2.1.1
A TimeFilter for this entry. See the TimeFilter textual convention to see how this works.
Status: current	Access: not-accessible
OBJECT-TYPE
	TimeFilter

nlHostAddress		1.3.6.1.2.1.16.14.2.1.2
The network address for this nlHostEntry. This is represented as an octet string with specific semantics and length as identified by the protocolDirLocalIndex component of the index. For example, if the protocolDirLocalIndex indicates an encapsulation of ip, this object is encoded as a length octet of 4, followed by the 4 octets of the ip address, in network byte order.
Status: current	Access: not-accessible
OBJECT-TYPE
	OCTET STRING

nlHostInPkts		1.3.6.1.2.1.16.14.2.1.3
The number of packets without errors transmitted to this address since it was added to the nlHostTable. Note that this is the number of link-layer packets, so if a single network-layer packet is fragmented into several link-layer frames, this counter is incremented several times.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

nlHostOutPkts		1.3.6.1.2.1.16.14.2.1.4
The number of packets without errors transmitted by this address since it was added to the nlHostTable. Note that this is the number of link-layer packets, so if a single network-layer packet is fragmented into several link-layer frames, this counter is incremented several times.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

nlHostInOctets		1.3.6.1.2.1.16.14.2.1.5
The number of octets transmitted to this address since it was added to the nlHostTable (excluding framing bits but including FCS octets), excluding those octets in packets that contained errors. Note this doesn't count just those octets in the particular protocol frames, but includes the entire packet that contained the protocol.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

nlHostOutOctets		1.3.6.1.2.1.16.14.2.1.6
The number of octets transmitted by this address since it was added to the nlHostTable (excluding framing bits but including FCS octets), excluding those octets in packets that contained errors. Note this doesn't count just those octets in the particular protocol frames, but includes the entire packet that contained the protocol.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

nlHostOutMacNonUnicastPkts		1.3.6.1.2.1.16.14.2.1.7
The number of packets without errors transmitted by this address that were directed to any MAC broadcast addresses or to any MAC multicast addresses since this host was added to the nlHostTable. Note that this is the number of link-layer packets, so if a single network-layer packet is fragmented into several link-layer frames, this counter is incremented several times.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

nlHostCreateTime		1.3.6.1.2.1.16.14.2.1.8
The value of sysUpTime when this entry was last activated. This can be used by the management station to ensure that the entry has not been deleted and recreated between polls.
Status: current	Access: read-only
OBJECT-TYPE
	LastCreateTime

hlMatrixControlTable		1.3.6.1.2.1.16.15.1
A list of higher layer (i.e. non-MAC) matrix control entries. These entries will enable the collection of the network and application level matrix tables containing conversation statistics indexed by pairs of network addresses. Both the network and application level matrix tables are controlled by this table is so that they will both be created and deleted at the same time, further increasing the ease with which they can be implemented as a single datastore (note that if an implementation stores application layer matrix records in memory, it can derive network layer matrix records from them). Entries in the nlMatrixSDTable and nlMatrixDSTable will be created on behalf of each entry in this table. Additionally, if this probe implements the alMatrix tables, entries in the alMatrix tables will be created on behalf of each entry in this table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HlMatrixControlEntry

hlMatrixControlEntry		1.3.6.1.2.1.16.15.1.1
A conceptual row in the hlMatrixControlTable. An example of indexing of this entry is hlMatrixControlNlDroppedFrames.1
Status: current	Access: not-accessible
OBJECT-TYPE
	HlMatrixControlEntry

hlMatrixControlIndex		1.3.6.1.2.1.16.15.1.1.1
An index that uniquely identifies an entry in the hlMatrixControlTable. Each such entry defines a function that discovers conversations on a particular interface and places statistics about them in the nlMatrixSDTable and the nlMatrixDSTable, and optionally the alMatrixSDTable and alMatrixDSTable, on behalf of this hlMatrixControlEntry.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..65535

hlMatrixControlDataSource		1.3.6.1.2.1.16.15.1.1.2
The source of the data for the associated matrix tables. The statistics in this group reflect all packets on the local network segment attached to the identified interface. This object may not be modified if the associated hlMatrixControlStatus object is equal to active(1).
Status: current	Access: read-create
OBJECT-TYPE
	DataSource

hlMatrixControlNlDroppedFrames		1.3.6.1.2.1.16.15.1.1.3
The total number of frames which were received by the probe and therefore not accounted for in the *StatsDropEvents, but for which the probe chose not to count for this entry for whatever reason. Most often, this event occurs when the probe is out of some resources and decides to shed load from this collection. This count does not include packets that were not counted because they had MAC-layer errors. Note that if the nlMatrixTables are inactive because no protocols are enabled in the protocol directory, this value should be 0. Note that, unlike the dropEvents counter, this number is the exact number of frames dropped.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hlMatrixControlNlInserts		1.3.6.1.2.1.16.15.1.1.4
The number of times an nlMatrix entry has been inserted into the nlMatrix tables. If an entry is inserted, then deleted, and then inserted, this counter will be incremented by 2. The addition of a conversation into both the nlMatrixSDTable and nlMatrixDSTable shall be counted as two insertions (even though every addition into one table must be accompanied by an insertion into the other). To allow for efficient implementation strategies, agents may delay updating this object for short periods of time. For example, an implementation strategy may allow internal data structures to differ from those visible via SNMP for short periods of time. This counter may reflect the internal data structures for those short periods of time. Note that the sum of then nlMatrixSDTable and nlMatrixDSTable sizes can be determined by subtracting hlMatrixControlNlDeletes from hlMatrixControlNlInserts.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hlMatrixControlNlDeletes		1.3.6.1.2.1.16.15.1.1.5
The number of times an nlMatrix entry has been deleted from the nlMatrix tables (for any reason). If an entry is deleted, then inserted, and then deleted, this counter will be incremented by 2. The deletion of a conversation from both the nlMatrixSDTable and nlMatrixDSTable shall be counted as two deletions (even though every deletion from one table must be accompanied by a deletion from the other). To allow for efficient implementation strategies, agents may delay updating this object for short periods of time. For example, an implementation strategy may allow internal data structures to differ from those visible via SNMP for short periods of time. This counter may reflect the internal data structures for those short periods of time. Note that the table size can be determined by subtracting hlMatrixControlNlDeletes from hlMatrixControlNlInserts.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hlMatrixControlNlMaxDesiredEntries		1.3.6.1.2.1.16.15.1.1.6
The maximum number of entries that are desired in the nlMatrix tables on behalf of this control entry. The probe will not create more than this number of associated entries in the table, but may choose to create fewer entries in this table for any reason including the lack of resources. If this object is set to a value less than the current number of entries, enough entries are chosen in an implementation-dependent manner and deleted so that the number of entries in the table equals the value of this object. If this value is set to -1, the probe may create any number of entries in this table. If the associated hlMatrixControlStatus object is equal to `active', this object may not be modified. This object may be used to control how resources are allocated on the probe for the various RMON functions.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	-1..2147483647

hlMatrixControlAlDroppedFrames		1.3.6.1.2.1.16.15.1.1.7
The total number of frames which were received by the probe and therefore not accounted for in the *StatsDropEvents, but for which the probe chose not to count for this entry for whatever reason. Most often, this event occurs when the probe is out of some resources and decides to shed load from this collection. This count does not include packets that were not counted because they had MAC-layer errors. Note that if the alMatrixTables are not implemented or are inactive because no protocols are enabled in the protocol directory, this value should be 0. Note that, unlike the dropEvents counter, this number is the exact number of frames dropped.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hlMatrixControlAlInserts		1.3.6.1.2.1.16.15.1.1.8
The number of times an alMatrix entry has been inserted into the alMatrix tables. If an entry is inserted, then deleted, and then inserted, this counter will be incremented by 2. The addition of a conversation into both the alMatrixSDTable and alMatrixDSTable shall be counted as two insertions (even though every addition into one table must be accompanied by an insertion into the other). To allow for efficient implementation strategies, agents may delay updating this object for short periods of time. For example, an implementation strategy may allow internal data structures to differ from those visible via SNMP for short periods of time. This counter may reflect the internal data structures for those short periods of time. Note that the table size can be determined by subtracting hlMatrixControlAlDeletes from hlMatrixControlAlInserts.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hlMatrixControlAlDeletes		1.3.6.1.2.1.16.15.1.1.9
The number of times an alMatrix entry has been deleted from the alMatrix tables. If an entry is deleted, then inserted, and then deleted, this counter will be incremented by 2. The deletion of a conversation from both the alMatrixSDTable and alMatrixDSTable shall be counted as two deletions (even though every deletion from one table must be accompanied by a deletion from the other). To allow for efficient implementation strategies, agents may delay updating this object for short periods of time. For example, an implementation strategy may allow internal data structures to differ from those visible via SNMP for short periods of time. This counter may reflect the internal data structures for those short periods of time. Note that the table size can be determined by subtracting hlMatrixControlAlDeletes from hlMatrixControlAlInserts.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hlMatrixControlAlMaxDesiredEntries		1.3.6.1.2.1.16.15.1.1.10
The maximum number of entries that are desired in the alMatrix tables on behalf of this control entry. The probe will not create more than this number of associated entries in the table, but may choose to create fewer entries in this table for any reason including the lack of resources. If this object is set to a value less than the current number of entries, enough entries are chosen in an implementation-dependent manner and deleted so that the number of entries in the table equals the value of this object. If this value is set to -1, the probe may create any number of entries in this table. If the associated hlMatrixControlStatus object is equal to `active', this object may not be modified. This object may be used to control how resources are allocated on the probe for the various RMON functions.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	-1..2147483647

hlMatrixControlOwner		1.3.6.1.2.1.16.15.1.1.11
The entity that configured this entry and is therefore using the resources assigned to it.
Status: current	Access: read-create
OBJECT-TYPE
	OwnerString

hlMatrixControlStatus		1.3.6.1.2.1.16.15.1.1.12
The status of this hlMatrixControlEntry. An entry may not exist in the active state unless all objects in the entry have an appropriate value. If this object is not equal to active(1), all associated entries in the nlMatrixSDTable, nlMatrixDSTable, alMatrixSDTable, and the alMatrixDSTable shall be deleted by the agent.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

nlMatrixSDTable		1.3.6.1.2.1.16.15.2
A list of traffic matrix entries which collect statistics for conversations between two network-level addresses. This table is indexed first by the source address and then by the destination address to make it convenient to collect all conversations from a particular address. The probe will populate this table for all network layer protocols in the protocol directory table whose value of protocolDirMatrixConfig is equal to supportedOn(3), and will delete any entries whose protocolDirEntry is deleted or has a protocolDirMatrixConfig value of supportedOff(2). The probe will add to this table all pairs of addresses seen in all packets with no MAC errors, and will increment octet and packet counts in the table for all packets with no MAC errors. Further, this table will only contain entries that have a corresponding entry in the nlMatrixDSTable with the same source address and destination address.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		NlMatrixSDEntry

nlMatrixSDEntry		1.3.6.1.2.1.16.15.2.1
A conceptual row in the nlMatrixSDTable. The hlMatrixControlIndex value in the index identifies the hlMatrixControlEntry on whose behalf this entry was created. The protocolDirLocalIndex value in the index identifies the network layer protocol of the nlMatrixSDSourceAddress and nlMatrixSDDestAddress. An example of the indexing of this table is nlMatrixSDPkts.1.783495.18.4.128.2.6.6.4.128.2.6.7
Status: current	Access: not-accessible
OBJECT-TYPE
	NlMatrixSDEntry

nlMatrixSDTimeMark		1.3.6.1.2.1.16.15.2.1.1
A TimeFilter for this entry. See the TimeFilter textual convention to see how this works.
Status: current	Access: not-accessible
OBJECT-TYPE
	TimeFilter

nlMatrixSDSourceAddress		1.3.6.1.2.1.16.15.2.1.2
The network source address for this nlMatrixSDEntry. This is represented as an octet string with specific semantics and length as identified by the protocolDirLocalIndex component of the index. For example, if the protocolDirLocalIndex indicates an encapsulation of ip, this object is encoded as a length octet of 4, followed by the 4 octets of the ip address, in network byte order.
Status: current	Access: not-accessible
OBJECT-TYPE
	OCTET STRING

nlMatrixSDDestAddress		1.3.6.1.2.1.16.15.2.1.3
The network destination address for this nlMatrixSDEntry. This is represented as an octet string with specific semantics and length as identified by the protocolDirLocalIndex component of the index. For example, if the protocolDirLocalIndex indicates an encapsulation of ip, this object is encoded as a length octet of 4, followed by the 4 octets of the ip address, in network byte order.
Status: current	Access: not-accessible
OBJECT-TYPE
	OCTET STRING

nlMatrixSDPkts		1.3.6.1.2.1.16.15.2.1.4
The number of packets without errors transmitted from the source address to the destination address since this entry was added to the nlMatrixSDTable. Note that this is the number of link-layer packets, so if a single network-layer packet is fragmented into several link-layer frames, this counter is incremented several times.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

nlMatrixSDOctets		1.3.6.1.2.1.16.15.2.1.5
The number of octets transmitted from the source address to the destination address since this entry was added to the nlMatrixSDTable (excluding framing bits but including FCS octets), excluding those octets in packets that contained errors. Note this doesn't count just those octets in the particular protocol frames, but includes the entire packet that contained the protocol.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

nlMatrixSDCreateTime		1.3.6.1.2.1.16.15.2.1.6
The value of sysUpTime when this entry was last activated. This can be used by the management station to ensure that the entry has not been deleted and recreated between polls.
Status: current	Access: read-only
OBJECT-TYPE
	LastCreateTime

nlMatrixDSTable		1.3.6.1.2.1.16.15.3
A list of traffic matrix entries which collect statistics for conversations between two network-level addresses. This table is indexed first by the destination address and then by the source address to make it convenient to collect all conversations to a particular address. The probe will populate this table for all network layer protocols in the protocol directory table whose value of protocolDirMatrixConfig is equal to supportedOn(3), and will delete any entries whose protocolDirEntry is deleted or has a protocolDirMatrixConfig value of supportedOff(2). The probe will add to this table all pairs of addresses seen in all packets with no MAC errors, and will increment octet and packet counts in the table for all packets with no MAC errors. Further, this table will only contain entries that have a corresponding entry in the nlMatrixSDTable with the same source address and destination address.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		NlMatrixDSEntry

nlMatrixDSEntry		1.3.6.1.2.1.16.15.3.1
A conceptual row in the nlMatrixDSTable. The hlMatrixControlIndex value in the index identifies the hlMatrixControlEntry on whose behalf this entry was created. The protocolDirLocalIndex value in the index identifies the network layer protocol of the nlMatrixDSSourceAddress and nlMatrixDSDestAddress. An example of the indexing of this table is nlMatrixDSPkts.1.783495.18.4.128.2.6.7.4.128.2.6.6
Status: current	Access: not-accessible
OBJECT-TYPE
	NlMatrixDSEntry

nlMatrixDSTimeMark		1.3.6.1.2.1.16.15.3.1.1
A TimeFilter for this entry. See the TimeFilter textual convention to see how this works.
Status: current	Access: not-accessible
OBJECT-TYPE
	TimeFilter

nlMatrixDSSourceAddress		1.3.6.1.2.1.16.15.3.1.2
The network source address for this nlMatrixDSEntry. This is represented as an octet string with specific semantics and length as identified by the protocolDirLocalIndex component of the index. For example, if the protocolDirLocalIndex indicates an encapsulation of ip, this object is encoded as a length octet of 4, followed by the 4 octets of the ip address, in network byte order.
Status: current	Access: not-accessible
OBJECT-TYPE
	OCTET STRING

nlMatrixDSDestAddress		1.3.6.1.2.1.16.15.3.1.3
The network destination address for this nlMatrixDSEntry. This is represented as an octet string with specific semantics and length as identified by the protocolDirLocalIndex component of the index. For example, if the protocolDirLocalIndex indicates an encapsulation of ip, this object is encoded as a length octet of 4, followed by the 4 octets of the ip address, in network byte order.
Status: current	Access: not-accessible
OBJECT-TYPE
	OCTET STRING

nlMatrixDSPkts		1.3.6.1.2.1.16.15.3.1.4
The number of packets without errors transmitted from the source address to the destination address since this entry was added to the nlMatrixDSTable. Note that this is the number of link-layer packets, so if a single network-layer packet is fragmented into several link-layer frames, this counter is incremented several times.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

nlMatrixDSOctets		1.3.6.1.2.1.16.15.3.1.5
The number of octets transmitted from the source address to the destination address since this entry was added to the nlMatrixDSTable (excluding framing bits but including FCS octets), excluding those octets in packets that contained errors. Note this doesn't count just those octets in the particular protocol frames, but includes the entire packet that contained the protocol.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

nlMatrixDSCreateTime		1.3.6.1.2.1.16.15.3.1.6
The value of sysUpTime when this entry was last activated. This can be used by the management station to ensure that the entry has not been deleted and recreated between polls.
Status: current	Access: read-only
OBJECT-TYPE
	LastCreateTime

nlMatrixTopNControlTable		1.3.6.1.2.1.16.15.4
A set of parameters that control the creation of a report of the top N matrix entries according to a selected metric.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		NlMatrixTopNControlEntry

nlMatrixTopNControlEntry		1.3.6.1.2.1.16.15.4.1
A conceptual row in the nlMatrixTopNControlTable. An example of the indexing of this table is nlMatrixTopNControlDuration.3
Status: current	Access: not-accessible
OBJECT-TYPE
	NlMatrixTopNControlEntry

nlMatrixTopNControlIndex		1.3.6.1.2.1.16.15.4.1.1
An index that uniquely identifies an entry in the nlMatrixTopNControlTable. Each such entry defines one top N report prepared for one interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..65535

nlMatrixTopNControlMatrixIndex		1.3.6.1.2.1.16.15.4.1.2
The nlMatrix[SD/DS] table for which a top N report will be prepared on behalf of this entry. The nlMatrix[SD/DS] table is identified by the value of the hlMatrixControlIndex for that table - that value is used here to identify the particular table. This object may not be modified if the associated nlMatrixTopNControlStatus object is equal to active(1).
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..65535

nlMatrixTopNControlRateBase		1.3.6.1.2.1.16.15.4.1.3
The variable for each nlMatrix[SD/DS] entry that the nlMatrixTopNEntries are sorted by. This object may not be modified if the associated nlMatrixTopNControlStatus object is equal to active(1).
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	nlMatrixTopNPkts(1), nlMatrixTopNOctets(2)

nlMatrixTopNControlTimeRemaining		1.3.6.1.2.1.16.15.4.1.4
The number of seconds left in the report currently being collected. When this object is modified by the management station, a new collection is started, possibly aborting a currently running report. The new value is used as the requested duration of this report, and is immediately loaded into the associated nlMatrixTopNControlDuration object. When the report finishes, the probe will automatically start another collection with the same initial value of nlMatrixTopNControlTimeRemaining. Thus the management station may simply read the resulting reports repeatedly, checking the startTime and duration each time to ensure that a report was not missed or that the report parameters were not changed. While the value of this object is non-zero, it decrements by one per second until it reaches zero. At the time that this object decrements to zero, the report is made accessible in the nlMatrixTopNTable, overwriting any report that may be there. When this object is modified by the management station, any associated entries in the nlMatrixTopNTable shall be deleted. (Note that this is a different algorithm than the one used in the hostTopNTable).
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..2147483647

nlMatrixTopNControlGeneratedReports		1.3.6.1.2.1.16.15.4.1.5
The number of reports that have been generated by this entry.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

nlMatrixTopNControlDuration		1.3.6.1.2.1.16.15.4.1.6
The number of seconds that this report has collected during the last sampling interval. When the associated nlMatrixTopNControlTimeRemaining object is set, this object shall be set by the probe to the same value and shall not be modified until the next time the nlMatrixTopNControlTimeRemaining is set. This value shall be zero if no reports have been requested for this nlMatrixTopNControlEntry.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

nlMatrixTopNControlRequestedSize		1.3.6.1.2.1.16.15.4.1.7
The maximum number of matrix entries requested for this report. When this object is created or modified, the probe should set nlMatrixTopNControlGrantedSize as closely to this object as is possible for the particular probe implementation and available resources.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..2147483647

nlMatrixTopNControlGrantedSize		1.3.6.1.2.1.16.15.4.1.8
The maximum number of matrix entries in this report. When the associated nlMatrixTopNControlRequestedSize object is created or modified, the probe should set this object as closely to the requested value as is possible for the particular implementation and available resources. The probe must not lower this value except as a result of a set to the associated nlMatrixTopNControlRequestedSize object. If the value of nlMatrixTopNControlRateBase is equal to nlMatrixTopNPkts, when the next topN report is generated, matrix entries with the highest value of nlMatrixTopNPktRate shall be placed in this table in decreasing order of this rate until there is no more room or until there are no more matrix entries. If the value of nlMatrixTopNControlRateBase is equal to nlMatrixTopNOctets, when the next topN report is generated, matrix entries with the highest value of nlMatrixTopNOctetRate shall be placed in this table in decreasing order of this rate until there is no more room or until there are no more matrix entries. It is an implementation-specific matter how entries with the same value of nlMatrixTopNPktRate or nlMatrixTopNOctetRate are sorted. It is also an implementation-specific matter as to whether or not zero-valued entries are available.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

nlMatrixTopNControlStartTime		1.3.6.1.2.1.16.15.4.1.9
The value of sysUpTime when this top N report was last started. In other words, this is the time that the associated nlMatrixTopNControlTimeRemaining object was modified to start the requested report or the time the report was last automatically (re)started. This object may be used by the management station to determine if a report was missed or not.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

nlMatrixTopNControlOwner		1.3.6.1.2.1.16.15.4.1.10
The entity that configured this entry and is therefore using the resources assigned to it.
Status: current	Access: read-create
OBJECT-TYPE
	OwnerString

nlMatrixTopNControlStatus		1.3.6.1.2.1.16.15.4.1.11
The status of this nlMatrixTopNControlEntry. An entry may not exist in the active state unless all objects in the entry have an appropriate value. If this object is not equal to active(1), all associated entries in the nlMatrixTopNTable shall be deleted by the agent.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

nlMatrixTopNTable		1.3.6.1.2.1.16.15.5
A set of statistics for those network layer matrix entries that have counted the highest number of octets or packets.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		NlMatrixTopNEntry

nlMatrixTopNEntry		1.3.6.1.2.1.16.15.5.1
A conceptual row in the nlMatrixTopNTable. The nlMatrixTopNControlIndex value in the index identifies the nlMatrixTopNControlEntry on whose behalf this entry was created. An example of the indexing of this table is nlMatrixTopNPktRate.3.10
Status: current	Access: not-accessible
OBJECT-TYPE
	NlMatrixTopNEntry

nlMatrixTopNIndex		1.3.6.1.2.1.16.15.5.1.1
An index that uniquely identifies an entry in the nlMatrixTopNTable among those in the same report. This index is between 1 and N, where N is the number of entries in this report. If the value of nlMatrixTopNControlRateBase is equal to nlMatrixTopNPkts, increasing values of nlMatrixTopNIndex shall be assigned to entries with decreasing values of nlMatrixTopNPktRate until index N is assigned or there are no more nlMatrixTopNEntries. If the value of nlMatrixTopNControlRateBase is equal to nlMatrixTopNOctets, increasing values of nlMatrixTopNIndex shall be assigned to entries with decreasing values of nlMatrixTopNOctetRate until index N is assigned or there are no more nlMatrixTopNEntries.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..65535

nlMatrixTopNProtocolDirLocalIndex		1.3.6.1.2.1.16.15.5.1.2
The protocolDirLocalIndex of the network layer protocol of this entry's network address.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..2147483647

nlMatrixTopNSourceAddress		1.3.6.1.2.1.16.15.5.1.3
The network layer address of the source host in this conversation. This is represented as an octet string with specific semantics and length as identified by the associated nlMatrixTopNProtocolDirLocalIndex. For example, if the protocolDirLocalIndex indicates an encapsulation of ip, this object is encoded as a length octet of 4, followed by the 4 octets of the ip address, in network byte order.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

nlMatrixTopNDestAddress		1.3.6.1.2.1.16.15.5.1.4
The network layer address of the destination host in this conversation. This is represented as an octet string with specific semantics and length as identified by the associated nlMatrixTopNProtocolDirLocalIndex. For example, if the nlMatrixTopNProtocolDirLocalIndex indicates an encapsulation of ip, this object is encoded as a length octet of 4, followed by the 4 octets of the ip address, in network byte order.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

nlMatrixTopNPktRate		1.3.6.1.2.1.16.15.5.1.5
The number of packets seen from the source host to the destination host during this sampling interval, counted using the rules for counting the nlMatrixSDPkts object. If the value of nlMatrixTopNControlRateBase is nlMatrixTopNPkts, this variable will be used to sort this report.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

nlMatrixTopNReversePktRate		1.3.6.1.2.1.16.15.5.1.6
The number of packets seen from the destination host to the source host during this sampling interval, counted using the rules for counting the nlMatrixSDPkts object (note that the corresponding nlMatrixSDPkts object selected is the one whose source address is equal to nlMatrixTopNDestAddress and whose destination address is equal to nlMatrixTopNSourceAddress.) Note that if the value of nlMatrixTopNControlRateBase is equal to nlMatrixTopNPkts, the sort of topN entries is based entirely on nlMatrixTopNPktRate, and not on the value of this object.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

nlMatrixTopNOctetRate		1.3.6.1.2.1.16.15.5.1.7
The number of octets seen from the source host to the destination host during this sampling interval, counted using the rules for counting the nlMatrixSDOctets object. If the value of nlMatrixTopNControlRateBase is nlMatrixTopNOctets, this variable will be used to sort this report.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

nlMatrixTopNReverseOctetRate		1.3.6.1.2.1.16.15.5.1.8
The number of octets seen from the destination host to the source host during this sampling interval, counted using the rules for counting the nlMatrixDSOctets object (note that the corresponding nlMatrixSDOctets object selected is the one whose source address is equal to nlMatrixTopNDestAddress and whose destination address is equal to nlMatrixTopNSourceAddress.) Note that if the value of nlMatrixTopNControlRateBase is equal to nlMatrixTopNOctets, the sort of topN entries is based entirely on nlMatrixTopNOctetRate, and not on the value of this object.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

alHostTable		1.3.6.1.2.1.16.16.1
A collection of statistics for a particular protocol from a particular network address that has been discovered on an interface of this device. The probe will populate this table for all protocols in the protocol directory table whose value of protocolDirHostConfig is equal to supportedOn(3), and will delete any entries whose protocolDirEntry is deleted or has a protocolDirHostConfig value of supportedOff(2). The probe will add to this table all addresses seen as the source or destination address in all packets with no MAC errors, and will increment octet and packet counts in the table for all packets with no MAC errors. Further, entries will only be added to this table if their address exists in the nlHostTable and will be deleted from this table if their address is deleted from the nlHostTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlHostEntry

alHostEntry		1.3.6.1.2.1.16.16.1.1
A conceptual row in the alHostTable. The hlHostControlIndex value in the index identifies the hlHostControlEntry on whose behalf this entry was created. The first protocolDirLocalIndex value in the index identifies the network layer protocol of the address. The nlHostAddress value in the index identifies the network layer address of this entry. The second protocolDirLocalIndex value in the index identifies the protocol that is counted by this entry. An example of the indexing in this entry is alHostOutPkts.1.783495.18.4.128.2.6.6.34
Status: current	Access: not-accessible
OBJECT-TYPE
	AlHostEntry

alHostTimeMark		1.3.6.1.2.1.16.16.1.1.1
A TimeFilter for this entry. See the TimeFilter textual convention to see how this works.
Status: current	Access: not-accessible
OBJECT-TYPE
	TimeFilter

alHostInPkts		1.3.6.1.2.1.16.16.1.1.2
The number of packets of this protocol type without errors transmitted to this address since it was added to the alHostTable. Note that this is the number of link-layer packets, so if a single network-layer packet is fragmented into several link-layer frames, this counter is incremented several times.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

alHostOutPkts		1.3.6.1.2.1.16.16.1.1.3
The number of packets of this protocol type without errors transmitted by this address since it was added to the alHostTable. Note that this is the number of link-layer packets, so if a single network-layer packet is fragmented into several link-layer frames, this counter is incremented several times.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

alHostInOctets		1.3.6.1.2.1.16.16.1.1.4
The number of octets transmitted to this address of this protocol type since it was added to the alHostTable (excluding framing bits but including FCS octets), excluding those octets in packets that contained errors. Note this doesn't count just those octets in the particular protocol frames, but includes the entire packet that contained the protocol.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

alHostOutOctets		1.3.6.1.2.1.16.16.1.1.5
The number of octets transmitted by this address of this protocol type since it was added to the alHostTable (excluding framing bits but including FCS octets), excluding those octets in packets that contained errors. Note this doesn't count just those octets in the particular protocol frames, but includes the entire packet that contained the protocol.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

alHostCreateTime		1.3.6.1.2.1.16.16.1.1.6
The value of sysUpTime when this entry was last activated. This can be used by the management station to ensure that the entry has not been deleted and recreated between polls.
Status: current	Access: read-only
OBJECT-TYPE
	LastCreateTime

alMatrixSDTable		1.3.6.1.2.1.16.17.1
A list of application traffic matrix entries which collect statistics for conversations of a particular protocol between two network-level addresses. This table is indexed first by the source address and then by the destination address to make it convenient to collect all statistics from a particular address. The probe will populate this table for all protocols in the protocol directory table whose value of protocolDirMatrixConfig is equal to supportedOn(3), and will delete any entries whose protocolDirEntry is deleted or has a protocolDirMatrixConfig value of supportedOff(2). The probe will add to this table all pairs of addresses for all protocols seen in all packets with no MAC errors, and will increment octet and packet counts in the table for all packets with no MAC errors. Further, entries will only be added to this table if their address pair exists in the nlMatrixSDTable and will be deleted from this table if the address pair is deleted from the nlMatrixSDTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlMatrixSDEntry

alMatrixSDEntry		1.3.6.1.2.1.16.17.1.1
A conceptual row in the alMatrixSDTable. The hlMatrixControlIndex value in the index identifies the hlMatrixControlEntry on whose behalf this entry was created. The first protocolDirLocalIndex value in the index identifies the network layer protocol of the nlMatrixSDSourceAddress and nlMatrixSDDestAddress. The nlMatrixSDSourceAddress value in the index identifies the network layer address of the source host in this conversation. The nlMatrixSDDestAddress value in the index identifies the network layer address of the destination host in this conversation. The second protocolDirLocalIndex value in the index identifies the protocol that is counted by this entry. An example of the indexing of this entry is alMatrixSDPkts.1.783495.18.4.128.2.6.6.4.128.2.6.7.34
Status: current	Access: not-accessible
OBJECT-TYPE
	AlMatrixSDEntry

alMatrixSDTimeMark		1.3.6.1.2.1.16.17.1.1.1
A TimeFilter for this entry. See the TimeFilter textual convention to see how this works.
Status: current	Access: not-accessible
OBJECT-TYPE
	TimeFilter

alMatrixSDPkts		1.3.6.1.2.1.16.17.1.1.2
The number of packets of this protocol type without errors transmitted from the source address to the destination address since this entry was added to the alMatrixSDTable. Note that this is the number of link-layer packets, so if a single network-layer packet is fragmented into several link-layer frames, this counter is incremented several times.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

alMatrixSDOctets		1.3.6.1.2.1.16.17.1.1.3
The number of octets in packets of this protocol type transmitted from the source address to the destination address since this entry was added to the alMatrixSDTable (excluding framing bits but including FCS octets), excluding those octets in packets that contained errors. Note this doesn't count just those octets in the particular protocol frames, but includes the entire packet that contained the protocol.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

alMatrixSDCreateTime		1.3.6.1.2.1.16.17.1.1.4
The value of sysUpTime when this entry was last activated. This can be used by the management station to ensure that the entry has not been deleted and recreated between polls.
Status: current	Access: read-only
OBJECT-TYPE
	LastCreateTime

alMatrixDSTable		1.3.6.1.2.1.16.17.2
A list of application traffic matrix entries which collect statistics for conversations of a particular protocol between two network-level addresses. This table is indexed first by the destination address and then by the source address to make it convenient to collect all statistics to a particular address. The probe will populate this table for all protocols in the protocol directory table whose value of protocolDirMatrixConfig is equal to supportedOn(3), and will delete any entries whose protocolDirEntry is deleted or has a protocolDirMatrixConfig value of supportedOff(2). The probe will add to this table all pairs of addresses for all protocols seen in all packets with no MAC errors, and will increment octet and packet counts in the table for all packets with no MAC errors. Further, entries will only be added to this table if their address pair exists in the nlMatrixDSTable and will be deleted from this table if the address pair is deleted from the nlMatrixDSTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlMatrixDSEntry

alMatrixDSEntry		1.3.6.1.2.1.16.17.2.1
A conceptual row in the alMatrixDSTable. The hlMatrixControlIndex value in the index identifies the hlMatrixControlEntry on whose behalf this entry was created. The first protocolDirLocalIndex value in the index identifies the network layer protocol of the alMatrixDSSourceAddress and alMatrixDSDestAddress. The nlMatrixDSDestAddress value in the index identifies the network layer address of the destination host in this conversation. The nlMatrixDSSourceAddress value in the index identifies the network layer address of the source host in this conversation. The second protocolDirLocalIndex value in the index identifies the protocol that is counted by this entry. An example of the indexing of this entry is alMatrixDSPkts.1.783495.18.4.128.2.6.7.4.128.2.6.6.34
Status: current	Access: not-accessible
OBJECT-TYPE
	AlMatrixDSEntry

alMatrixDSTimeMark		1.3.6.1.2.1.16.17.2.1.1
A TimeFilter for this entry. See the TimeFilter textual convention to see how this works.
Status: current	Access: not-accessible
OBJECT-TYPE
	TimeFilter

alMatrixDSPkts		1.3.6.1.2.1.16.17.2.1.2
The number of packets of this protocol type without errors transmitted from the source address to the destination address since this entry was added to the alMatrixDSTable. Note that this is the number of link-layer packets, so if a single network-layer packet is fragmented into several link-layer frames, this counter is incremented several times.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

alMatrixDSOctets		1.3.6.1.2.1.16.17.2.1.3
The number of octets in packets of this protocol type transmitted from the source address to the destination address since this entry was added to the alMatrixDSTable (excluding framing bits but including FCS octets), excluding those octets in packets that contained errors. Note this doesn't count just those octets in the particular protocol frames, but includes the entire packet that contained the protocol.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

alMatrixDSCreateTime		1.3.6.1.2.1.16.17.2.1.4
The value of sysUpTime when this entry was last activated. This can be used by the management station to ensure that the entry has not been deleted and recreated between polls.
Status: current	Access: read-only
OBJECT-TYPE
	LastCreateTime

alMatrixTopNControlTable		1.3.6.1.2.1.16.17.3
A set of parameters that control the creation of a report of the top N matrix entries according to a selected metric.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlMatrixTopNControlEntry

alMatrixTopNControlEntry		1.3.6.1.2.1.16.17.3.1
A conceptual row in the alMatrixTopNControlTable. An example of the indexing of this table is alMatrixTopNControlDuration.3
Status: current	Access: not-accessible
OBJECT-TYPE
	AlMatrixTopNControlEntry

alMatrixTopNControlIndex		1.3.6.1.2.1.16.17.3.1.1
An index that uniquely identifies an entry in the alMatrixTopNControlTable. Each such entry defines one top N report prepared for one interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..65535

alMatrixTopNControlMatrixIndex		1.3.6.1.2.1.16.17.3.1.2
The alMatrix[SD/DS] table for which a top N report will be prepared on behalf of this entry. The alMatrix[SD/DS] table is identified by the value of the hlMatrixControlIndex for that table - that value is used here to identify the particular table. This object may not be modified if the associated alMatrixTopNControlStatus object is equal to active(1).
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..65535

alMatrixTopNControlRateBase		1.3.6.1.2.1.16.17.3.1.3
The variable for each alMatrix[SD/DS] entry that the alMatrixTopNEntries are sorted by, as well as the selector of the view of the matrix table that will be used. The values alMatrixTopNTerminalsPkts and alMatrixTopNTerminalsOctets cause collection only from protocols that have no child protocols that are counted. The values alMatrixTopNAllPkts and alMatrixTopNAllOctets cause collection from all alMatrix entries. This object may not be modified if the associated alMatrixTopNControlStatus object is equal to active(1).
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	alMatrixTopNTerminalsPkts(1), alMatrixTopNTerminalsOctets(2), alMatrixTopNAllPkts(3), alMatrixTopNAllOctets(4)

alMatrixTopNControlTimeRemaining		1.3.6.1.2.1.16.17.3.1.4
The number of seconds left in the report currently being collected. When this object is modified by the management station, a new collection is started, possibly aborting a currently running report. The new value is used as the requested duration of this report, and is immediately loaded into the associated alMatrixTopNControlDuration object. When the report finishes, the probe will automatically start another collection with the same initial value of alMatrixTopNControlTimeRemaining. Thus the management station may simply read the resulting reports repeatedly, checking the startTime and duration each time to ensure that a report was not missed or that the report parameters were not changed. While the value of this object is non-zero, it decrements by one per second until it reaches zero. At the time that this object decrements to zero, the report is made accessible in the alMatrixTopNTable, overwriting any report that may be there. When this object is modified by the management station, any associated entries in the alMatrixTopNTable shall be deleted. (Note that this is a different algorithm than the one used in the hostTopNTable).
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..2147483647

alMatrixTopNControlGeneratedReports		1.3.6.1.2.1.16.17.3.1.5
The number of reports that have been generated by this entry.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

alMatrixTopNControlDuration		1.3.6.1.2.1.16.17.3.1.6
The number of seconds that this report has collected during the last sampling interval. When the associated alMatrixTopNControlTimeRemaining object is set, this object shall be set by the probe to the same value and shall not be modified until the next time the alMatrixTopNControlTimeRemaining is set. This value shall be zero if no reports have been requested for this alMatrixTopNControlEntry.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

alMatrixTopNControlRequestedSize		1.3.6.1.2.1.16.17.3.1.7
The maximum number of matrix entries requested for this report. When this object is created or modified, the probe should set alMatrixTopNControlGrantedSize as closely to this object as is possible for the particular probe implementation and available resources.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..2147483647

alMatrixTopNControlGrantedSize		1.3.6.1.2.1.16.17.3.1.8
The maximum number of matrix entries in this report. When the associated alMatrixTopNControlRequestedSize object is created or modified, the probe should set this object as closely to the requested value as is possible for the particular implementation and available resources. The probe must not lower this value except as a result of a set to the associated alMatrixTopNControlRequestedSize object. If the value of alMatrixTopNControlRateBase is equal to alMatrixTopNTerminalsPkts or alMatrixTopNAllPkts, when the next topN report is generated, matrix entries with the highest value of alMatrixTopNPktRate shall be placed in this table in decreasing order of this rate until there is no more room or until there are no more matrix entries. If the value of alMatrixTopNControlRateBase is equal to alMatrixTopNTerminalsOctets or alMatrixTopNAllOctets, when the next topN report is generated, matrix entries with the highest value of alMatrixTopNOctetRate shall be placed in this table in decreasing order of this rate until there is no more room or until there are no more matrix entries. It is an implementation-specific matter how entries with the same value of alMatrixTopNPktRate or alMatrixTopNOctetRate are sorted. It is also an implementation-specific matter as to whether or not zero-valued entries are available.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

alMatrixTopNControlStartTime		1.3.6.1.2.1.16.17.3.1.9
The value of sysUpTime when this top N report was last started. In other words, this is the time that the associated alMatrixTopNControlTimeRemaining object was modified to start the requested report or the time the report was last automatically (re)started. This object may be used by the management station to determine if a report was missed or not.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

alMatrixTopNControlOwner		1.3.6.1.2.1.16.17.3.1.10
The entity that configured this entry and is therefore using the resources assigned to it.
Status: current	Access: read-create
OBJECT-TYPE
	OwnerString

alMatrixTopNControlStatus		1.3.6.1.2.1.16.17.3.1.11
The status of this alMatrixTopNControlEntry. An entry may not exist in the active state unless all objects in the entry have an appropriate value. If this object is not equal to active(1), all associated entries in the alMatrixTopNTable shall be deleted by the agent.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

alMatrixTopNTable		1.3.6.1.2.1.16.17.4
A set of statistics for those application layer matrix entries that have counted the highest number of octets or packets.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlMatrixTopNEntry

alMatrixTopNEntry		1.3.6.1.2.1.16.17.4.1
A conceptual row in the alMatrixTopNTable. The alMatrixTopNControlIndex value in the index identifies the alMatrixTopNControlEntry on whose behalf this entry was created. An example of the indexing of this table is alMatrixTopNPktRate.3.10
Status: current	Access: not-accessible
OBJECT-TYPE
	AlMatrixTopNEntry

alMatrixTopNIndex		1.3.6.1.2.1.16.17.4.1.1
An index that uniquely identifies an entry in the alMatrixTopNTable among those in the same report. This index is between 1 and N, where N is the number of entries in this report. If the value of alMatrixTopNControlRateBase is equal to alMatrixTopNTerminalsPkts or alMatrixTopNAllPkts, increasing values of alMatrixTopNIndex shall be assigned to entries with decreasing values of alMatrixTopNPktRate until index N is assigned or there are no more alMatrixTopNEntries. If the value of alMatrixTopNControlRateBase is equal to alMatrixTopNTerminalsOctets or alMatrixTopNAllOctets, increasing values of alMatrixTopNIndex shall be assigned to entries with decreasing values of alMatrixTopNOctetRate until index N is assigned or there are no more alMatrixTopNEntries.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..65535

alMatrixTopNProtocolDirLocalIndex		1.3.6.1.2.1.16.17.4.1.2
The protocolDirLocalIndex of the network layer protocol of this entry's network address.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..2147483647

alMatrixTopNSourceAddress		1.3.6.1.2.1.16.17.4.1.3
The network layer address of the source host in this conversation. This is represented as an octet string with specific semantics and length as identified by the associated alMatrixTopNProtocolDirLocalIndex. For example, if the alMatrixTopNProtocolDirLocalIndex indicates an encapsulation of ip, this object is encoded as a length octet of 4, followed by the 4 octets of the ip address, in network byte order.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

alMatrixTopNDestAddress		1.3.6.1.2.1.16.17.4.1.4
The network layer address of the destination host in this conversation. This is represented as an octet string with specific semantics and length as identified by the associated alMatrixTopNProtocolDirLocalIndex. For example, if the alMatrixTopNProtocolDirLocalIndex indicates an encapsulation of ip, this object is encoded as a length octet of 4, followed by the 4 octets of the ip address, in network byte order.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

alMatrixTopNAppProtocolDirLocalIndex		1.3.6.1.2.1.16.17.4.1.5
The type of the protocol counted by this matrix entry.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..2147483647

alMatrixTopNPktRate		1.3.6.1.2.1.16.17.4.1.6
The number of packets seen of this protocol from the source host to the destination host during this sampling interval, counted using the rules for counting the alMatrixSDPkts object. If the value of alMatrixTopNControlRateBase is alMatrixTopNTerminalsPkts or alMatrixTopNAllPkts, this variable will be used to sort this report.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

alMatrixTopNReversePktRate		1.3.6.1.2.1.16.17.4.1.7
The number of packets seen of this protocol from the destination host to the source host during this sampling interval, counted using the rules for counting the alMatrixDSPkts object (note that the corresponding alMatrixSDPkts object selected is the one whose source address is equal to alMatrixTopNDestAddress and whose destination address is equal to alMatrixTopNSourceAddress.) Note that if the value of alMatrixTopNControlRateBase is equal to alMatrixTopNTerminalsPkts or alMatrixTopNAllPkts, the sort of topN entries is based entirely on alMatrixTopNPktRate, and not on the value of this object.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

alMatrixTopNOctetRate		1.3.6.1.2.1.16.17.4.1.8
The number of octets seen of this protocol from the source host to the destination host during this sampling interval, counted using the rules for counting the alMatrixSDOctets object. If the value of alMatrixTopNControlRateBase is alMatrixTopNTerminalsOctets or alMatrixTopNAllOctets, this variable will be used to sort this report.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

alMatrixTopNReverseOctetRate		1.3.6.1.2.1.16.17.4.1.9
The number of octets seen of this protocol from the destination host to the source host during this sampling interval, counted using the rules for counting the alMatrixDSOctets object (note that the corresponding alMatrixSDOctets object selected is the one whose source address is equal to alMatrixTopNDestAddress and whose destination address is equal to alMatrixTopNSourceAddress.) Note that if the value of alMatrixTopNControlRateBase is equal to alMatrixTopNTerminalsOctets or alMatrixTopNAllOctets, the sort of topN entries is based entirely on alMatrixTopNOctetRate, and not on the value of this object.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

usrHistoryControlTable		1.3.6.1.2.1.16.18.1
A list of data-collection configuration entries.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		UsrHistoryControlEntry

usrHistoryControlEntry		1.3.6.1.2.1.16.18.1.1
A list of parameters that set up a group of user-defined MIB objects to be sampled periodically (called a bucket-group). For example, an instance of usrHistoryControlInterval might be named usrHistoryControlInterval.1
Status: current	Access: not-accessible
OBJECT-TYPE
	UsrHistoryControlEntry

usrHistoryControlIndex		1.3.6.1.2.1.16.18.1.1.1
An index that uniquely identifies an entry in the usrHistoryControlTable. Each such entry defines a set of samples at a particular interval for a specified set of MIB instances available from the managed system.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..65535

usrHistoryControlObjects		1.3.6.1.2.1.16.18.1.1.2
The number of MIB objects to be collected in the portion of usrHistoryTable associated with this usrHistoryControlEntry. This object may not be modified if the associated instance of usrHistoryControlStatus is equal to active(1).
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..65535

usrHistoryControlBucketsRequested		1.3.6.1.2.1.16.18.1.1.3
The requested number of discrete time intervals over which data is to be saved in the part of the usrHistoryTable associated with this usrHistoryControlEntry. When this object is created or modified, the probe should set usrHistoryControlBucketsGranted as closely to this object as is possible for the particular probe implementation and available resources.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..65535

usrHistoryControlBucketsGranted		1.3.6.1.2.1.16.18.1.1.4
The number of discrete sampling intervals over which data shall be saved in the part of the usrHistoryTable associated with this usrHistoryControlEntry. When the associated usrHistoryControlBucketsRequested object is created or modified, the probe should set this object as closely to the requested value as is possible for the particular probe implementation and available resources. The probe must not lower this value except as a result of a modification to the associated usrHistoryControlBucketsRequested object. The associated usrHistoryControlBucketsRequested object should be set before or at the same time as this object to allow the probe to accurately estimate the resources required for this usrHistoryControlEntry. There will be times when the actual number of buckets associated with this entry is less than the value of this object. In this case, at the end of each sampling interval, a new bucket will be added to the usrHistoryTable. When the number of buckets reaches the value of this object and a new bucket is to be added to the usrHistoryTable, the oldest bucket associated with this usrHistoryControlEntry shall be deleted by the agent so that the new bucket can be added. When the value of this object changes to a value less than the current value, entries are deleted from the usrHistoryTable associated with this usrHistoryControlEntry. Enough of the oldest of these entries shall be deleted by the agent so that their number remains less than or equal to the new value of this object. When the value of this object changes to a value greater than the current value, the number of associated usrHistory entries may be allowed to grow.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

usrHistoryControlInterval		1.3.6.1.2.1.16.18.1.1.5
The interval in seconds over which the data is sampled for each bucket in the part of the usrHistory table associated with this usrHistoryControlEntry. Because the counters in a bucket may overflow at their maximum value with no indication, a prudent manager will take into account the possibility of overflow in any of the associated counters. It is important to consider the minimum time in which any counter could overflow on a particular media type and set the usrHistoryControlInterval object to a value less than this interval. This object may not be modified if the associated usrHistoryControlStatus object is equal to active(1).
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..2147483647

usrHistoryControlOwner		1.3.6.1.2.1.16.18.1.1.6
The entity that configured this entry and is therefore using the resources assigned to it.
Status: current	Access: read-create
OBJECT-TYPE
	OwnerString

usrHistoryControlStatus		1.3.6.1.2.1.16.18.1.1.7
The status of this variable history control entry. An entry may not exist in the active state unless all objects in the entry have an appropriate value. If this object is not equal to active(1), all associated entries in the usrHistoryTable shall be deleted.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

usrHistoryObjectTable		1.3.6.1.2.1.16.18.2
A list of data-collection configuration entries.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		UsrHistoryObjectEntry

usrHistoryObjectEntry		1.3.6.1.2.1.16.18.2.1
A list of MIB instances to be sampled periodically. Entries in this table are created when an associated usrHistoryControlObjects object is created. The usrHistoryControlIndex value in the index is that of the associated usrHistoryControlEntry. For example, an instance of usrHistoryObjectVariable might be usrHistoryObjectVariable.1.3
Status: current	Access: not-accessible
OBJECT-TYPE
	UsrHistoryObjectEntry

usrHistoryObjectIndex		1.3.6.1.2.1.16.18.2.1.1
An index used to uniquely identify an entry in the usrHistoryObject table. Each such entry defines a MIB instance to be collected periodically.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..65535

usrHistoryObjectVariable		1.3.6.1.2.1.16.18.2.1.2
The object identifier of the particular variable to be sampled. Only variables that resolve to an ASN.1 primitive type of Integer32 (Integer32, Counter, Gauge, or TimeTicks) may be sampled. Because SNMP access control is articulated entirely in terms of the contents of MIB views, no access control mechanism exists that can restrict the value of this object to identify only those objects that exist in a particular MIB view. Because there is thus no acceptable means of restricting the read access that could be obtained through the user history mechanism, the probe must only grant write access to this object in those views that have read access to all objects on the probe. During a set operation, if the supplied variable name is not available in the selected MIB view, a badValue error must be returned. This object may not be modified if the associated usrHistoryControlStatus object is equal to active(1).
Status: current	Access: read-create
OBJECT-TYPE
	OBJECT IDENTIFIER

usrHistoryObjectSampleType		1.3.6.1.2.1.16.18.2.1.3
The method of sampling the selected variable for storage in the usrHistoryTable. If the value of this object is absoluteValue(1), the value of the selected variable will be copied directly into the history bucket. If the value of this object is deltaValue(2), the value of the selected variable at the last sample will be subtracted from the current value, and the difference will be stored in the history bucket. If the associated usrHistoryObjectVariable instance could not be obtained at the previous sample interval, then a delta sample is not possible, and the value of the associated usrHistoryValStatus object for this interval will be valueNotAvailable(1). This object may not be modified if the associated usrHistoryControlStatus object is equal to active(1).
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	absoluteValue(1), deltaValue(2)

usrHistoryTable		1.3.6.1.2.1.16.18.3
A list of user defined history entries.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		UsrHistoryEntry

usrHistoryEntry		1.3.6.1.2.1.16.18.3.1
A historical sample of user-defined variables. This sample is associated with the usrHistoryControlEntry which set up the parameters for a regular collection of these samples. The usrHistoryControlIndex value in the index identifies the usrHistoryControlEntry on whose behalf this entry was created. The usrHistoryObjectIndex value in the index identifies the usrHistoryObjectEntry on whose behalf this entry was created. For example, an instance of usrHistoryAbsValue, which represents the 14th sample of a variable collected as specified by usrHistoryControlEntry.1 and usrHistoryObjectEntry.1.5, would be named usrHistoryAbsValue.1.14.5
Status: current	Access: not-accessible
OBJECT-TYPE
	UsrHistoryEntry

usrHistorySampleIndex		1.3.6.1.2.1.16.18.3.1.1
An index that uniquely identifies the particular sample this entry represents among all samples associated with the same usrHistoryControlEntry. This index starts at 1 and increases by one as each new sample is taken.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..2147483647

usrHistoryIntervalStart		1.3.6.1.2.1.16.18.3.1.2
The value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of the time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collecting the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

usrHistoryIntervalEnd		1.3.6.1.2.1.16.18.3.1.3
The value of sysUpTime at the end of the interval over which this sample was measured.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

usrHistoryAbsValue		1.3.6.1.2.1.16.18.3.1.4
The absolute value (i.e. unsigned value) of the user-specified statistic during the last sampling period. The value during the current sampling period is not made available until the period is completed. To obtain the true value for this sampling interval, the associated instance of usrHistoryValStatus must be checked, and usrHistoryAbsValue adjusted as necessary. If the MIB instance could not be accessed during the sampling interval, then this object will have a value of zero and the associated instance of usrHistoryValStatus will be set to 'valueNotAvailable(1)'.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

usrHistoryValStatus		1.3.6.1.2.1.16.18.3.1.5
This object indicates the validity and sign of the data in the associated instance of usrHistoryAbsValue. If the MIB instance could not be accessed during the sampling interval, then 'valueNotAvailable(1)' will be returned. If the sample is valid and actual value of the sample is greater than or equal to zero then 'valuePositive(2)' is returned. If the sample is valid and the actual value of the sample is less than zero, 'valueNegative(3)' will be returned. The associated instance of usrHistoryAbsValue should be multiplied by -1 to obtain the true sample value.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	valueNotAvailable(1), valuePositive(2), valueNegative(3)

probeCapabilities		1.3.6.1.2.1.16.19.1
An indication of the RMON MIB groups supported on at least one interface by this probe.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(1)

probeSoftwareRev		1.3.6.1.2.1.16.19.2
The software revision of this device. This string will have a zero length if the revision is unknown.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..15)

probeHardwareRev		1.3.6.1.2.1.16.19.3
The hardware revision of this device. This string will have a zero length if the revision is unknown.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..31)

probeDateTime		1.3.6.1.2.1.16.19.4
Probe's current date and time. field octets contents range ----- ------ -------- ----- 1 1-2 year 0..65536 2 3 month 1..12 3 4 day 1..31 4 5 hour 0..23 5 6 minutes 0..59 6 7 seconds 0..60 (use 60 for leap-second) 7 8 deci-seconds 0..9 8 9 direction from UTC '+' / '-' 9 10 hours from UTC 0..11 10 11 minutes from UTC 0..59 For example, Tuesday May 26, 1992 at 1:30:15 PM EDT would be displayed as: 1992-5-26,13:30:15.0,-4:0 Note that if only local time is known, then timezone information (fields 8-10) is not present, and if no time information is known, the null string is returned.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0|8|11)

probeResetControl		1.3.6.1.2.1.16.19.5
Setting this object to warmBoot(2) causes the device to restart the application software with current configuration parameters saved in non-volatile memory. Setting this object to coldBoot(3) causes the device to reinitialize configuration parameters in non-volatile memory to default values and restart the application software. When the device is running normally, this variable has a value of running(1).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	running(1), warmBoot(2), coldBoot(3)

probeDownloadFile		1.3.6.1.2.1.16.19.6
The file name to be downloaded from the TFTP server when a download is next requested via this MIB. This value is set to the zero length string when no file name has been specified.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..127)

probeDownloadTFTPServer		1.3.6.1.2.1.16.19.7
The IP address of the TFTP server that contains the boot image to load when a download is next requested via this MIB. This value is set to `0.0.0.0' when no IP address has been specified.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

probeDownloadAction		1.3.6.1.2.1.16.19.8
When this object is set to downloadToRAM(2) or downloadToPROM(3), the device will discontinue its normal operation and begin download of the image specified by probeDownloadFile from the server specified by probeDownloadTFTPServer using the TFTP protocol. If downloadToRAM(2) is specified, the new image is copied to RAM only (the old image remains unaltered in the flash EPROM). If downloadToPROM(3) is specified the new image is written to the flash EPROM memory after its checksum has been verified to be correct. When the download process is completed, the device will warm boot to restart the newly loaded application. When the device is not downloading, this object will have a value of notDownloading(1).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notDownloading(1), downloadToPROM(2), downloadToRAM(3)

probeDownloadStatus		1.3.6.1.2.1.16.19.9
The status of the last download procedure, if any. This object will have a value of downloadStatusUnknown(2) if no download process has been performed.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	downloadSuccess(1), downloadStatusUnknown(2), downloadGeneralError(3), downloadNoResponseFromServer(4), downloadChecksumError(5), downloadIncompatibleImage(6), downloadTftpFileNotFound(7), downloadTftpAccessViolation(8)

serialConfigTable		1.3.6.1.2.1.16.19.10
A table of serial interface configuration entries. This data will be stored in non-volatile memory and preserved across probe resets or power loss.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SerialConfigEntry

serialConfigEntry		1.3.6.1.2.1.16.19.10.1
A set of configuration parameters for a particular serial interface on this device. If the device has no serial interfaces, this table is empty. The index is composed of the ifIndex assigned to this serial line interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SerialConfigEntry

serialMode		1.3.6.1.2.1.16.19.10.1.1
The type of incoming connection to expect on this serial interface.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	direct(1), modem(2)

serialProtocol		1.3.6.1.2.1.16.19.10.1.2
The type of data link encapsulation to be used on this serial interface.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	other(1), slip(2), ppp(3)

serialTimeout		1.3.6.1.2.1.16.19.10.1.3
This timeout value is used when the Management Station has initiated the conversation over the serial link. This variable represents the number of seconds of inactivity allowed before terminating the connection on this serial interface. Use the serialDialoutTimeout in the case where the probe has initiated the connection for the purpose of sending a trap.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..65535

serialModemInitString		1.3.6.1.2.1.16.19.10.1.4
A control string which controls how a modem attached to this serial interface should be initialized. The initialization is performed once during startup and again after each connection is terminated if the associated serialMode has the value of modem(2). A control string that is appropriate for a wide variety of modems is: '^s^MATE0Q0V1X4 S0=1 S2=43^M'.
Status: current	Access: read-create
OBJECT-TYPE
	ControlString	Size(0..255)

serialModemHangUpString		1.3.6.1.2.1.16.19.10.1.5
A control string which specifies how to disconnect a modem connection on this serial interface. This object is only meaningful if the associated serialMode has the value of modem(2). A control string that is appropriate for a wide variety of modems is: '^d2^s+++^d2^sATH0^M^d2'.
Status: current	Access: read-create
OBJECT-TYPE
	ControlString	Size(0..255)

serialModemConnectResp		1.3.6.1.2.1.16.19.10.1.6
An ASCII string containing substrings that describe the expected modem connection response code and associated bps rate. The substrings are delimited by the first character in the string, for example: /CONNECT/300/CONNECT 1200/1200/CONNECT 2400/2400/ CONNECT 4800/4800/CONNECT 9600/9600 will be interpreted as: response code bps rate CONNECT 300 CONNECT 1200 1200 CONNECT 2400 2400 CONNECT 4800 4800 CONNECT 9600 9600 The agent will use the information in this string to adjust the bps rate of this serial interface once a modem connection is established. A value that is appropriate for a wide variety of modems is: '/CONNECT/300/CONNECT 1200/1200/CONNECT 2400/2400/ CONNECT 4800/4800/CONNECT 9600/9600/CONNECT 14400/14400/ CONNECT 19200/19200/CONNECT 38400/38400/'.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..255)

serialModemNoConnectResp		1.3.6.1.2.1.16.19.10.1.7
An ASCII string containing response codes that may be generated by a modem to report the reason why a connection attempt has failed. The response codes are delimited by the first character in the string, for example: /NO CARRIER/BUSY/NO DIALTONE/NO ANSWER/ERROR/ If one of these response codes is received via this serial interface while attempting to make a modem connection, the agent will issue the hang up command as specified by serialModemHangUpString. A value that is appropriate for a wide variety of modems is: '/NO CARRIER/BUSY/NO DIALTONE/NO ANSWER/ERROR/'.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..255)

serialDialoutTimeout		1.3.6.1.2.1.16.19.10.1.8
This timeout value is used when the probe initiates the serial connection with the intention of contacting a management station. This variable represents the number of seconds of inactivity allowed before terminating the connection on this serial interface.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..65535

serialStatus		1.3.6.1.2.1.16.19.10.1.9
The status of this serialConfigEntry. An entry may not exist in the active state unless all objects in the entry have an appropriate value.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

netConfigTable		1.3.6.1.2.1.16.19.11
A table of netConfigEntries.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		NetConfigEntry

netConfigEntry		1.3.6.1.2.1.16.19.11.1
A set of configuration parameters for a particular network interface on this device. If the device has no network interface, this table is empty. The index is composed of the ifIndex assigned to the corresponding interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	NetConfigEntry

netConfigIPAddress		1.3.6.1.2.1.16.19.11.1.1
The IP address of this Net interface. The default value for this object is 0.0.0.0. If either the netConfigIPAddress or netConfigSubnetMask are 0.0.0.0, then when the device boots, it may use BOOTP to try to figure out what these values should be. If BOOTP fails, before the device can talk on the network, this value must be configured (e.g., through a terminal attached to the device). If BOOTP is used, care should be taken to not send BOOTP broadcasts too frequently and to eventually send very infrequently if no replies are received.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

netConfigSubnetMask		1.3.6.1.2.1.16.19.11.1.2
The subnet mask of this Net interface. The default value for this object is 0.0.0.0. If either the netConfigIPAddress or netConfigSubnetMask are 0.0.0.0, then when the device boots, it may use BOOTP to try to figure out what these values should be. If BOOTP fails, before the device can talk on the network, this value must be configured (e.g., through a terminal attached to the device). If BOOTP is used, care should be taken to not send BOOTP broadcasts too frequently and to eventually send very infrequently if no replies are received.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

netConfigStatus		1.3.6.1.2.1.16.19.11.1.3
The status of this netConfigEntry. An entry may not exist in the active state unless all objects in the entry have an appropriate value.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

netDefaultGateway		1.3.6.1.2.1.16.19.12
The IP Address of the default gateway. If this value is undefined or unknown, it shall have the value 0.0.0.0.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

trapDestTable		1.3.6.1.2.1.16.19.13
A list of trap destination entries.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TrapDestEntry

trapDestEntry		1.3.6.1.2.1.16.19.13.1
This entry includes a destination IP address to which to send traps for this community.
Status: current	Access: not-accessible
OBJECT-TYPE
	TrapDestEntry

trapDestIndex		1.3.6.1.2.1.16.19.13.1.1
A value that uniquely identifies this trapDestEntry.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..65535

trapDestCommunity		1.3.6.1.2.1.16.19.13.1.2
A community to which this destination address belongs. This entry is associated with any eventEntries in the RMON MIB whose value of eventCommunity is equal to the value of this object. Every time an associated event entry sends a trap due to an event, that trap will be sent to each address in the trapDestTable with a trapDestCommunity equal to eventCommunity. This object may not be modified if the associated trapDestStatus object is equal to active(1).
Status: current	Access: read-create
OBJECT-TYPE
	OCTET STRING	Size(0..127)

trapDestProtocol		1.3.6.1.2.1.16.19.13.1.3
The protocol with which to send this trap.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	ip(1), ipx(2)

trapDestAddress		1.3.6.1.2.1.16.19.13.1.4
The address to send traps on behalf of this entry. If the associated trapDestProtocol object is equal to ip(1), the encoding of this object is the same as the snmpUDPAddress textual convention in [RFC1906]: -- for a SnmpUDPAddress of length 6: -- -- octets contents encoding -- 1-4 IP-address network-byte order -- 5-6 UDP-port network-byte order If the associated trapDestProtocol object is equal to ipx(2), the encoding of this object is the same as the snmpIPXAddress textual convention in [RFC1906]: -- for a SnmpIPXAddress of length 12: -- -- octets contents encoding -- 1-4 network-number network-byte order -- 5-10 physical-address network-byte order -- 11-12 socket-number network-byte order This object may not be modified if the associated trapDestStatus object is equal to active(1).
Status: current	Access: read-create
OBJECT-TYPE
	OCTET STRING

trapDestOwner		1.3.6.1.2.1.16.19.13.1.5
The entity that configured this entry and is therefore using the resources assigned to it.
Status: current	Access: read-create
OBJECT-TYPE
	OwnerString

trapDestStatus		1.3.6.1.2.1.16.19.13.1.6
The status of this trap destination entry. An entry may not exist in the active state unless all objects in the entry have an appropriate value.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

serialConnectionTable		1.3.6.1.2.1.16.19.14
A list of serialConnectionEntries.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SerialConnectionEntry

serialConnectionEntry		1.3.6.1.2.1.16.19.14.1
Configuration for a SLIP link over a serial line.
Status: current	Access: not-accessible
OBJECT-TYPE
	SerialConnectionEntry

serialConnectIndex		1.3.6.1.2.1.16.19.14.1.1
A value that uniquely identifies this serialConnection entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..65535

serialConnectDestIpAddress		1.3.6.1.2.1.16.19.14.1.2
The IP Address that can be reached at the other end of this serial connection. This object may not be modified if the associated serialConnectStatus object is equal to active(1).
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

serialConnectType		1.3.6.1.2.1.16.19.14.1.3
The type of outgoing connection to make. If this object has the value direct(1), then a direct serial connection is assumed. If this object has the value modem(2), then serialConnectDialString will be used to make a modem connection. If this object has the value switch(3), then serialConnectSwitchConnectSeq will be used to establish the connection over a serial data switch, and serialConnectSwitchDisconnectSeq will be used to terminate the connection. If this object has the value modem-switch(4), then a modem connection will be made first followed by the switch connection. This object may not be modified if the associated serialConnectStatus object is equal to active(1).
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	direct(1), modem(2), switch(3), modemSwitch(4)

serialConnectDialString		1.3.6.1.2.1.16.19.14.1.4
A control string which specifies how to dial the phone number in order to establish a modem connection. The string should include dialing prefix and suffix. For example: ``^s^MATD9,888-1234^M'' will instruct the Probe to send a carriage return followed by the dialing prefix ``ATD'', the phone number ``9,888-1234'', and a carriage return as the dialing suffix. This object may not be modified if the associated serialConnectStatus object is equal to active(1).
Status: current	Access: read-create
OBJECT-TYPE
	ControlString	Size(0..255)

serialConnectSwitchConnectSeq		1.3.6.1.2.1.16.19.14.1.5
A control string which specifies how to establish a data switch connection. This object may not be modified if the associated serialConnectStatus object is equal to active(1).
Status: current	Access: read-create
OBJECT-TYPE
	ControlString	Size(0..255)

serialConnectSwitchDisconnectSeq		1.3.6.1.2.1.16.19.14.1.6
A control string which specifies how to terminate a data switch connection. This object may not be modified if the associated serialConnectStatus object is equal to active(1).
Status: current	Access: read-create
OBJECT-TYPE
	ControlString	Size(0..255)

serialConnectSwitchResetSeq		1.3.6.1.2.1.16.19.14.1.7
A control string which specifies how to reset a data switch in the event of a timeout. This object may not be modified if the associated serialConnectStatus object is equal to active(1).
Status: current	Access: read-create
OBJECT-TYPE
	ControlString	Size(0..255)

serialConnectOwner		1.3.6.1.2.1.16.19.14.1.8
The entity that configured this entry and is therefore using the resources assigned to it.
Status: current	Access: read-create
OBJECT-TYPE
	OwnerString

serialConnectStatus		1.3.6.1.2.1.16.19.14.1.9
The status of this serialConnectionEntry. If the manager attempts to set this object to active(1) when the serialConnectType is set to modem(2) or modem-switch(4) and the serialConnectDialString is a zero-length string or cannot be correctly parsed as a ConnectString, the set request will be rejected with badValue(3). If the manager attempts to set this object to active(1) when the serialConnectType is set to switch(3) or modem-switch(4) and the serialConnectSwitchConnectSeq, the serialConnectSwitchDisconnectSeq, or the serialConnectSwitchResetSeq are zero-length strings or cannot be correctly parsed as ConnectStrings, the set request will be rejected with badValue(3). An entry may not exist in the active state unless all objects in the entry have an appropriate value.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

etherStats2Table		1.3.6.1.2.1.16.1.4
Contains the RMON-2 augmentations to RMON-1.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EtherStats2Entry

etherStats2Entry		1.3.6.1.2.1.16.1.4.1
Contains the RMON-2 augmentations to RMON-1.
Status: current	Access: not-accessible
OBJECT-TYPE
	EtherStats2Entry

etherStatsDroppedFrames		1.3.6.1.2.1.16.1.4.1.1
The total number of frames which were received by the probe and therefore not accounted for in the *StatsDropEvents, but for which the probe chose not to count for this entry for whatever reason. Most often, this event occurs when the probe is out of some resources and decides to shed load from this collection. This count does not include packets that were not counted because they had MAC-layer errors. Note that, unlike the dropEvents counter, this number is the exact number of frames dropped.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

etherStatsCreateTime		1.3.6.1.2.1.16.1.4.1.2
The value of sysUpTime when this control entry was last activated. This can be used by the management station to ensure that the table has not been deleted and recreated between polls.
Status: current	Access: read-only
OBJECT-TYPE
	LastCreateTime

historyControl2Table		1.3.6.1.2.1.16.2.5
Contains the RMON-2 augmentations to RMON-1.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HistoryControl2Entry

historyControl2Entry		1.3.6.1.2.1.16.2.5.1
Contains the RMON-2 augmentations to RMON-1.
Status: current	Access: not-accessible
OBJECT-TYPE
	HistoryControl2Entry

historyControlDroppedFrames		1.3.6.1.2.1.16.2.5.1.1
The total number of frames which were received by the probe and therefore not accounted for in the *StatsDropEvents, but for which the probe chose not to count for this entry for whatever reason. Most often, this event occurs when the probe is out of some resources and decides to shed load from this collection. This count does not include packets that were not counted because they had MAC-layer errors. Note that, unlike the dropEvents counter, this number is the exact number of frames dropped.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hostControl2Table		1.3.6.1.2.1.16.4.4
Contains the RMON-2 augmentations to RMON-1.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HostControl2Entry

hostControl2Entry		1.3.6.1.2.1.16.4.4.1
Contains the RMON-2 augmentations to RMON-1.
Status: current	Access: not-accessible
OBJECT-TYPE
	HostControl2Entry

hostControlDroppedFrames		1.3.6.1.2.1.16.4.4.1.1
The total number of frames which were received by the probe and therefore not accounted for in the *StatsDropEvents, but for which the probe chose not to count for this entry for whatever reason. Most often, this event occurs when the probe is out of some resources and decides to shed load from this collection. This count does not include packets that were not counted because they had MAC-layer errors. Note that, unlike the dropEvents counter, this number is the exact number of frames dropped.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hostControlCreateTime		1.3.6.1.2.1.16.4.4.1.2
The value of sysUpTime when this control entry was last activated. This can be used by the management station to ensure that the table has not been deleted and recreated between polls.
Status: current	Access: read-only
OBJECT-TYPE
	LastCreateTime

matrixControl2Table		1.3.6.1.2.1.16.6.4
Contains the RMON-2 augmentations to RMON-1.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MatrixControl2Entry

matrixControl2Entry		1.3.6.1.2.1.16.6.4.1
Contains the RMON-2 augmentations to RMON-1.
Status: current	Access: not-accessible
OBJECT-TYPE
	MatrixControl2Entry

matrixControlDroppedFrames		1.3.6.1.2.1.16.6.4.1.1
The total number of frames which were received by the probe and therefore not accounted for in the *StatsDropEvents, but for which the probe chose not to count for this entry for whatever reason. Most often, this event occurs when the probe is out of some resources and decides to shed load from this collection. This count does not include packets that were not counted because they had MAC-layer errors. Note that, unlike the dropEvents counter, this number is the exact number of frames dropped.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

matrixControlCreateTime		1.3.6.1.2.1.16.6.4.1.2
The value of sysUpTime when this control entry was last activated. This can be used by the management station to ensure that the table has not been deleted and recreated between polls.
Status: current	Access: read-only
OBJECT-TYPE
	LastCreateTime

channel2Table		1.3.6.1.2.1.16.7.3
Contains the RMON-2 augmentations to RMON-1.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Channel2Entry

channel2Entry		1.3.6.1.2.1.16.7.3.1
Contains the RMON-2 augmentations to RMON-1.
Status: current	Access: not-accessible
OBJECT-TYPE
	Channel2Entry

channelDroppedFrames		1.3.6.1.2.1.16.7.3.1.1
The total number of frames which were received by the probe and therefore not accounted for in the *StatsDropEvents, but for which the probe chose not to count for this entry for whatever reason. Most often, this event occurs when the probe is out of some resources and decides to shed load from this collection. This count does not include packets that were not counted because they had MAC-layer errors. Note that, unlike the dropEvents counter, this number is the exact number of frames dropped.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

channelCreateTime		1.3.6.1.2.1.16.7.3.1.2
The value of sysUpTime when this control entry was last activated. This can be used by the management station to ensure that the table has not been deleted and recreated between polls.
Status: current	Access: read-only
OBJECT-TYPE
	LastCreateTime

tokenRingMLStats2Table		1.3.6.1.2.1.16.1.5
Contains the RMON-2 augmentations to RMON-1.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TokenRingMLStats2Entry

tokenRingMLStats2Entry		1.3.6.1.2.1.16.1.5.1
Contains the RMON-2 augmentations to RMON-1.
Status: current	Access: not-accessible
OBJECT-TYPE
	TokenRingMLStats2Entry

tokenRingMLStatsDroppedFrames		1.3.6.1.2.1.16.1.5.1.1
The total number of frames which were received by the probe and therefore not accounted for in the *StatsDropEvents, but for which the probe chose not to count for this entry for whatever reason. Most often, this event occurs when the probe is out of some resources and decides to shed load from this collection. This count does not include packets that were not counted because they had MAC-layer errors. Note that, unlike the dropEvents counter, this number is the exact number of frames dropped.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

tokenRingMLStatsCreateTime		1.3.6.1.2.1.16.1.5.1.2
The value of sysUpTime when this control entry was last activated. This can be used by the management station to ensure that the table has not been deleted and recreated between polls.
Status: current	Access: read-only
OBJECT-TYPE
	LastCreateTime

tokenRingPStats2Table		1.3.6.1.2.1.16.1.6
Contains the RMON-2 augmentations to RMON-1.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TokenRingPStats2Entry

tokenRingPStats2Entry		1.3.6.1.2.1.16.1.6.1
Contains the RMON-2 augmentations to RMON-1.
Status: current	Access: not-accessible
OBJECT-TYPE
	TokenRingPStats2Entry

tokenRingPStatsDroppedFrames		1.3.6.1.2.1.16.1.6.1.1
The total number of frames which were received by the probe and therefore not accounted for in the *StatsDropEvents, but for which the probe chose not to count for this entry for whatever reason. Most often, this event occurs when the probe is out of some resources and decides to shed load from this collection. This count does not include packets that were not counted because they had MAC-layer errors. Note that, unlike the dropEvents counter, this number is the exact number of frames dropped.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

tokenRingPStatsCreateTime		1.3.6.1.2.1.16.1.6.1.2
The value of sysUpTime when this control entry was last activated. This can be used by the management station to ensure that the table has not been deleted and recreated between polls.
Status: current	Access: read-only
OBJECT-TYPE
	LastCreateTime

ringStationControl2Table		1.3.6.1.2.1.16.10.7
Contains the RMON-2 augmentations to RMON-1.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RingStationControl2Entry

ringStationControl2Entry		1.3.6.1.2.1.16.10.7.1
Contains the RMON-2 augmentations to RMON-1.
Status: current	Access: not-accessible
OBJECT-TYPE
	RingStationControl2Entry

ringStationControlDroppedFrames		1.3.6.1.2.1.16.10.7.1.1
The total number of frames which were received by the probe and therefore not accounted for in the *StatsDropEvents, but for which the probe chose not to count for this entry for whatever reason. Most often, this event occurs when the probe is out of some resources and decides to shed load from this collection. This count does not include packets that were not counted because they had MAC-layer errors. Note that, unlike the dropEvents counter, this number is the exact number of frames dropped.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ringStationControlCreateTime		1.3.6.1.2.1.16.10.7.1.2
The value of sysUpTime when this control entry was last activated. This can be used by the management station to ensure that the table has not been deleted and recreated between polls.
Status: current	Access: read-only
OBJECT-TYPE
	LastCreateTime

sourceRoutingStats2Table		1.3.6.1.2.1.16.10.8
Contains the RMON-2 augmentations to RMON-1.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SourceRoutingStats2Entry

sourceRoutingStats2Entry		1.3.6.1.2.1.16.10.8.1
Contains the RMON-2 augmentations to RMON-1.
Status: current	Access: not-accessible
OBJECT-TYPE
	SourceRoutingStats2Entry

sourceRoutingStatsDroppedFrames		1.3.6.1.2.1.16.10.8.1.1
The total number of frames which were received by the probe and therefore not accounted for in the *StatsDropEvents, but for which the probe chose not to count for this entry for whatever reason. Most often, this event occurs when the probe is out of some resources and decides to shed load from this collection. This count does not include packets that were not counted because they had MAC-layer errors. Note that, unlike the dropEvents counter, this number is the exact number of frames dropped.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

sourceRoutingStatsCreateTime		1.3.6.1.2.1.16.10.8.1.2
The value of sysUpTime when this control entry was last activated. This can be used by the management station to ensure that the table has not been deleted and recreated between polls.
Status: current	Access: read-only
OBJECT-TYPE
	LastCreateTime

filter2Table		1.3.6.1.2.1.16.7.4
Provides a variable-length packet filter feature to the RMON-1 filter table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Filter2Entry

filter2Entry		1.3.6.1.2.1.16.7.4.1
Provides a variable-length packet filter feature to the RMON-1 filter table.
Status: current	Access: not-accessible
OBJECT-TYPE
	Filter2Entry

filterProtocolDirDataLocalIndex		1.3.6.1.2.1.16.7.4.1.1
When this object is set to a non-zero value, the filter that it is associated with performs the following operations on every packet: 1) - If the packet doesn't match the protocol directory entry identified by this object, discard the packet and exit (i.e., discard the packet if it is not of the identified protocol). 2) - If the associated filterProtocolDirLocalIndex is non-zero and the packet doesn't match the protocol directory entry identified by that object, discard the packet and exit 3) - If the packet matches, perform the regular filter algorithm as if the beginning of this named protocol is the beginning of the packet, potentially applying the filterOffset value to move further into the packet.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..2147483647

filterProtocolDirLocalIndex		1.3.6.1.2.1.16.7.4.1.2
When this object is set to a non-zero value, the filter that it is associated with will discard the packet if the packet doesn't match this protocol directory entry.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..2147483647

rmon2MIBCompliances		1.3.6.1.2.1.16.20.1
OBJECT IDENTIFIER

rmon2MIBGroups		1.3.6.1.2.1.16.20.2
OBJECT IDENTIFIER

rmon2MIBCompliance		1.3.6.1.2.1.16.20.1.1
Describes the requirements for conformance to the RMON2 MIB
Status: current	Access: read-create
MODULE-COMPLIANCE

rmon2MIBApplicationLayerCompliance		1.3.6.1.2.1.16.20.1.2
Describes the requirements for conformance to the RMON2 MIB with Application Layer Enhancements.
Status: current	Access: read-create
MODULE-COMPLIANCE

protocolDirectoryGroup		1.3.6.1.2.1.16.20.2.1
Lists the inventory of protocols the probe has the capability of monitoring and allows the addition, deletion, and configuration of entries in this list.
Status: current	Access: read-create
OBJECT-GROUP

protocolDistributionGroup		1.3.6.1.2.1.16.20.2.2
Collects the relative amounts of octets and packets for the different protocols detected on a network segment.
Status: current	Access: read-create
OBJECT-GROUP

addressMapGroup		1.3.6.1.2.1.16.20.2.3
Lists MAC address to network address bindings discovered by the probe and what interface they were last seen on.
Status: current	Access: read-create
OBJECT-GROUP

nlHostGroup		1.3.6.1.2.1.16.20.2.4
Counts the amount of traffic sent from and to each network address discovered by the probe. Note that while the hlHostControlTable also has objects that control an optional alHostTable, implementation of the alHostTable is not required to fully implement this group.
Status: current	Access: read-create
OBJECT-GROUP

nlMatrixGroup		1.3.6.1.2.1.16.20.2.5
Counts the amount of traffic sent between each pair of network addresses discovered by the probe. Note that while the hlMatrixControlTable also has objects that control optional alMatrixTables, implementation of the alMatrixTables is not required to fully implement this group.
Status: current	Access: read-create
OBJECT-GROUP

alHostGroup		1.3.6.1.2.1.16.20.2.6
Counts the amount of traffic, by protocol, sent from and to each network address discovered by the probe. Implementation of this group requires implementation of the Network Layer Host Group.
Status: current	Access: read-create
OBJECT-GROUP

alMatrixGroup		1.3.6.1.2.1.16.20.2.7
Counts the amount of traffic, by protocol, sent between each pair of network addresses discovered by the probe. Implementation of this group requires implementation of the Network Layer Matrix Group.
Status: current	Access: read-create
OBJECT-GROUP

usrHistoryGroup		1.3.6.1.2.1.16.20.2.8
The usrHistoryGroup provides user-defined collection of historical information from MIB objects on the probe.
Status: current	Access: read-create
OBJECT-GROUP

probeInformationGroup		1.3.6.1.2.1.16.20.2.9
This group describes various operating parameters of the probe as well as controlling the local time of the probe.
Status: current	Access: read-create
OBJECT-GROUP

probeConfigurationGroup		1.3.6.1.2.1.16.20.2.10
This group controls the configuration of various operating parameters of the probe.
Status: current	Access: read-create
OBJECT-GROUP

rmon1EnhancementGroup		1.3.6.1.2.1.16.20.2.11
This group adds some enhancements to RMON-1 that help management stations.
Status: current	Access: read-create
OBJECT-GROUP

rmon1EthernetEnhancementGroup		1.3.6.1.2.1.16.20.2.12
This group adds some enhancements to RMON-1 that help management stations.
Status: current	Access: read-create
OBJECT-GROUP

rmon1TokenRingEnhancementGroup		1.3.6.1.2.1.16.20.2.13
This group adds some enhancements to RMON-1 that help management stations.
Status: current	Access: read-create
OBJECT-GROUP