RFC1407-EXT-MIB
File:
RFC1407-EXT-MIB.mib (12342 bytes)
Imported modules
Imported symbols
Defined Types
| Cndsx3TotalExtEntry |
|
| SEQUENCE |
|
|
|
| |
cndsx3CellPayloadHECError |
Gauge |
|
| Cndsx3ConfigExtEntry |
|
| SEQUENCE |
|
|
|
| |
cndsx3LineBuildOut |
EnableIndicator |
|
| |
cndsx3LineIndex |
INTEGER |
|
| |
cndsx3ScramblingEnable |
EnableIndicator |
|
| |
cndsx3E3ConfigType |
INTEGER |
|
| Cndsx3OperEntry |
|
| SEQUENCE |
|
|
|
| |
cndsx3OperLineIndex |
INTEGER |
|
| |
cndsx3OperLineType |
INTEGER |
|
| |
cndsx3OperLoopbackConfig |
INTEGER |
|
| |
cndsx3OperLineStatus |
INTEGER |
|
| |
cndsx3OperTransmitClockSource |
INTEGER |
|
| |
cndsx3OperPlcpLOFEvent |
INTEGER |
|
| |
cndsx3OperG832CellDelineation |
INTEGER |
|
| |
cndsx3OperLineBuildOut |
EnableIndicator |
|
| |
cndsx3OperScramblingEnable |
EnableIndicator |
|
| |
cndsx3OperE3ConfigType |
INTEGER |
|
Defined Values
| cndsx3Oper |
1.3.6.1.4.1.930.3.6.1 |
| OBJECT IDENTIFIER |
|
|
|
| cndsx3TotalExtTable |
1.3.6.1.4.1.930.3.6.2.1 |
| This table contains the counters
that are additional to the
existing dsx3TotalTable |
| Status: mandatory |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
Cndsx3TotalExtEntry |
|
| cndsx3TotalExtEntry |
1.3.6.1.4.1.930.3.6.2.1.1 |
| An entry in the DS3/E3 TotalExt table. |
| Status: mandatory |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
Cndsx3TotalExtEntry |
|
|
| cndsx3ConfigExtTable |
1.3.6.1.4.1.930.3.6.3.1 |
| This table contains the configurable parameters
that are additional to the
existing dsx3ConfigTable |
| Status: mandatory |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
Cndsx3ConfigExtEntry |
|
| cndsx3ConfigExtEntry |
1.3.6.1.4.1.930.3.6.3.1.1 |
| An entry in the DS3/E3 ConfigExt table. |
| Status: mandatory |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
Cndsx3ConfigExtEntry |
|
|
| cndsx3LineIndex |
1.3.6.1.4.1.930.3.6.3.1.1.2 |
| This object is the identifier of a DS3/E3
Interface on a managed device. |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..65535 |
|
| cndsx3E3ConfigType |
1.3.6.1.4.1.930.3.6.3.1.1.4 |
| This object allows to switch between E3 G751 and G832 mode.
The following value is read-only:
other(1).......other than g751 and g832
The following value is read-write:
g751(2)........E3ConfigType is G751
g832(3)........E3ConfigType is G832 |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
other(1), g751(2), g832(3) |
|
| cndsx3OperTable |
1.3.6.1.4.1.930.3.6.1.1 |
| This table contains the configuration
information that are operational currently.
This table contains all the objects defined
in dsx3ConfigTable plus some additional.
This table is read only |
| Status: mandatory |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
Cndsx3OperEntry |
|
| cndsx3OperEntry |
1.3.6.1.4.1.930.3.6.1.1.1 |
| An entry in the DS3/E3 Operational Configuration table. |
| Status: mandatory |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
Cndsx3OperEntry |
|
|
| cndsx3OperLineIndex |
1.3.6.1.4.1.930.3.6.1.1.1.1 |
| This object is the identifier of a DS3/E3
Interface on a managed device. |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..65535 |
|
| cndsx3OperLineType |
1.3.6.1.4.1.930.3.6.1.1.1.2 |
| This variable indicates the variety of DS3 C-bit
or E3 application implementing this interface.
The type of interface affects the interpretation of the
usage and error statistics.
The rate of DS3 is 44.736 Mbps and E3 is 34.368 Mbps.
The dsx3ClearChannel value means that the C-bits
are not used except for sending/receiving AIS.
The values, in sequence, describe:
TITLE: SPECIFICATION:
dsx3M23 ANSI T1.107-1988
dsx3SYNTRAN ANSI T1.107-1988
dsx3CbitParity ANSI T1.107a-1989
dsx3ClearChannel ANSI T1.102-1987
e3Framed CCITT G.751
e3Plcp ETSI T/NA(91)18. |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
dsx3other(1), dsx3M23(2), dsx3SYNTRAN(3), dsx3CbitParity(4), dsx3ClearChannel(5), e3other(6), e3Framed(7), e3Plcp(8) |
|
| cndsx3OperLoopbackConfig |
1.3.6.1.4.1.930.3.6.1.1.1.3 |
| This variable represents the loopback configuration
of the DS3/E3 interface.
dsx3NoLoop
Not in the loopback state. A device that is
not capable of performing a loopback on
the interface shall always return this as
it's value.
dsx3PayloadLoop
The received signal at this interface is looped
through the device. Typically the received signal
is looped back for retransmission after it has
passed through the device's framing function.
dsx3LineLoop
The received signal at this interface does not
go through the device (minimum penetration) but
is looped back out.
dsx3OtherLoop
Loopbacks that are not defined here. |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
dsx3NoLoop(1), dsx3PayloadLoop(2), dsx3LineLoop(3), dsx3OtherLoop(4) |
|
| cndsx3OperLineStatus |
1.3.6.1.4.1.930.3.6.1.1.1.4 |
| This variable indicates the
Line Status of the interface.
It contains loopback state information
and failure state information.
The dsx3LineStatus is a bit map represented
as a sum, therefore, it can represent multiple failures
and a loopback (see dsx3LoopbackConfig object for the
type of loopback) simultaneously.
The dsx3NoAlarm should be set if and only if
no other flag is set.
The various bit positions are:
1 dsx3NoAlarm No alarm present
2 dsx3RcvRAIFailure Receiving Yellow/Remote
Alarm Indication
4 dsx3XmitRAIAlarm Transmitting Yellow/Remote
Alarm Indication
8 dsx3RcvAIS Receiving AIS failure state
16 dsx3XmitAIS Transmitting AIS
32 dsx3LOF Receiving LOF failure state
64 dsx3LOS Receiving LOS failure state
128 dsx3LoopbackState Looping the received signal
256 dsx3RcvTestCode Receiving a Test Pattern
512 dsx3OtherFailure any line status not defined here |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..1023 |
|
| cndsx3OperTransmitClockSource |
1.3.6.1.4.1.930.3.6.1.1.1.5 |
| The source of Transmit Clock.
is derived from the recovered receive clock of
another DS3 interface. |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
loopTiming(1), localTiming(2), throughTiming(3) |
|
| cndsx3OperPlcpLOFEvent |
1.3.6.1.4.1.930.3.6.1.1.1.6 |
| Indicates PLCP Loss of Frame event.
The following value is read-only:
on(1).......Loss of Frame event is present
off(2)......Loss of Frame event is not present |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
on(1), off(2) |
|
| cndsx3OperG832CellDelineation |
1.3.6.1.4.1.930.3.6.1.1.1.7 |
| Indicates Cell Delineation events.
The following value is read-only:
on(1).......Cell Delineation event is present
off(2)......Cell Delineation event is not present |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
on(1), off(2) |
|
| cndsx3OperE3ConfigType |
1.3.6.1.4.1.930.3.6.1.1.1.10 |
| This object shows E3Config mode.
The following value is read-only:
other(1).......other than g751 and g832
g751(2)........E3ConfigType is G751
g832(3)........E3ConfigType is G832 |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
other(1), g751(2), g832(3) |
|