RC-IP-MPLS-MIB

File: RC-IP-MPLS-MIB.mib (64543 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-TC	IF-MIB
RC-IP-MIB	MPLS-TC-STD-MIB	RAPID-CITY

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	Integer32
IpAddress	Unsigned32	TEXTUAL-CONVENTION
DisplayString	TruthValue	RowStatus
InterfaceIndex	rcIpMpls	MplsTunnelIndex
MplsTunnelInstanceIndex	EnableValue

Defined Types

MplsLsrId
A unique identifier for an MPLS LSR. This MAY represent an IpV4 address.
TEXTUAL-CONVENTION
	IpAddress

RcIpMplsInterfaceEntry
SEQUENCE
	rcIpMplsInterfaceIndex	Integer32
	rcIpMplsInterfaceLay3Addr	IpAddress
	rcIpMplsInterfaceLay3Mask	IpAddress
	rcIpMplsInterfaceAdminStatus	EnableValue
	rcIpMplsInterfaceIndLblDistMode	INTEGER
	rcIpMplsInterfaceConsLblRetenMode	INTEGER
	rcIpMplsInterfaceImdLblUseMode	INTEGER
	rcIpMplsInterfaceNoRouteReqRetryMode	TruthValue
	rcIpMplsInterfacePenultimatePopRequest	TruthValue
	rcIpMplsInterfacePropogateLabelReleaseRequest	TruthValue
	rcIpMplsInterfaceOnDemandAdvMode	INTEGER
	rcIpMplsInterfaceLabelRequestMode	INTEGER
	rcIpMplsInterfaceMtu	INTEGER
	rcIpMplsInterfaceLabelProtocol	INTEGER
	rcIpMplsInterfaceTraceFlag	TruthValue
	rcIpMplsInterfaceRowStatus	RowStatus

RcIpMplsLdpInterfaceEntry
SEQUENCE
	rcIpMplsLdpInterfaceIndex	Integer32
	rcIpMplsLdpInterfaceLay3Addr	IpAddress
	rcIpMplsLdpInterfaceLay3Mask	IpAddress
	rcIpMplsLdpInterfaceTargetHelloFlag	TruthValue
	rcIpMplsLdpInterfaceTargetResponseFlag	TruthValue
	rcIpMplsLdpInterfaceNonTtlLspFlag	TruthValue
	rcIpMplsLdpInterfaceRowStatus	RowStatus

RcIpMplsRsvpInterfaceEntry
SEQUENCE
	rcIpMplsRsvpInterfaceIndex	Integer32
	rcIpMplsRsvpInterfaceLay3Addr	IpAddress
	rcIpMplsRsvpInterfaceLay3Mask	IpAddress
	rcIpMplsRsvpInterfaceAuthFlag	TruthValue
	rcIpMplsRsvpInterfaceHelloFlag	TruthValue
	rcIpMplsRsvpInterfaceRefreshReductionFlag	TruthValue
	rcIpMplsRsvpInterfaceMemoryReductionFlag	TruthValue
	rcIpMplsRsvpInterfaceReliableFlag	TruthValue
	rcIpMplsRsvpInterfaceEPolicingFlag	TruthValue
	rcIpMplsRsvpInterfaceRowStatus	RowStatus

RcIpMplsLdpTargetAddrEntry
SEQUENCE
	rcIpMplsLdpTargetAddrBaseAddr	IpAddress
	rcIpMplsLdpTargetAddrTgtAddr	IpAddress
	rcIpMplsLdpTargetAddrRowStatus	RowStatus

RcIpMplsTunnelGroupEntry
SEQUENCE
	rcIpMplsTunnelGroupId	INTEGER
	rcIpMplsTunnelGroupDestAddr	IpAddress
	rcIpMplsTunnelGroupPrimaryTunnel	DisplayString
	rcIpMplsTunnelGroupActiveTunnel	INTEGER
	rcIpMplsTunnelGroupPersistentFlag	TruthValue
	rcIpMplsTunnelGroupOperation	INTEGER
	rcIpMplsTunnelGroupTunnelList	DisplayString
	rcIpMplsTunnelGroupFtnList	DisplayString
	rcIpMplsTunnelGroupBgpNeighbor	Integer32
	rcIpMplsTunnelGroupRowStatus	RowStatus
	rcIpMplsTunnelGroupBackupTunnel	DisplayString

RcIpMplsTeInterfaceEntry
SEQUENCE
	rcIpMplsTeInterfaceIndex	Integer32
	rcIpMplsTeInterfaceLay3Addr	IpAddress
	rcIpMplsTeInterfaceLay3Mask	IpAddress
	rcIpMplsTeInterfaceIgp	INTEGER
	rcIpMplsTeInterfaceMetric	INTEGER
	rcIpMplsTeInterfaceMaxBandwidth	INTEGER
	rcIpMplsTeInterfaceMaxReservableBandwidth	INTEGER
	rcIpMplsTeInterfaceResourceColor	OCTET STRING

RcIpMplsTunnelEntry
SEQUENCE
	rcIpMplsTunnelId	INTEGER
	rcIpMplsTunnelLabelRecordFlag	TruthValue
	rcIpMplsTunnelRowStatus	RowStatus

RcIpMplsTunnelExtEntry
SEQUENCE
	rcIpMplsTunnelExtIndex	MplsTunnelIndex
	rcIpMplsTunnelExtInstance	MplsTunnelInstanceIndex
	rcIpMplsTunnelExtIngressLSRId	MplsLsrId
	rcIpMplsTunnelExtEgressLSRId	MplsLsrId
	rcIpMplsTunnelExtFrrTableIndex	Unsigned32
	rcIpMplsTunnelExtRowStatus	RowStatus

RcIpMplsTunnelFrrEntry
SEQUENCE
	rcIpMplsTunnelFrrListIndex	Unsigned32
	rcIpMplsTunnelFrrSetupPrio	INTEGER
	rcIpMplsTunnelFrrHoldingPrio	INTEGER
	rcIpMplsTunnelFrrHopLimit	INTEGER
	rcIpMplsTunnelFrrBandwidth	INTEGER
	rcIpMplsTunnelFrrProtectionType	INTEGER
	rcIpMplsTunnelFrrExclAnyAffinity	OCTET STRING
	rcIpMplsTunnelFrrInclAnyAffinity	OCTET STRING
	rcIpMplsTunnelFrrInclAllAffinity	OCTET STRING
	rcIpMplsTunnelFrrLegacyFlag	TruthValue
	rcIpMplsTunnelFrrRowStatus	RowStatus

RcIpMplsTunnelHopToIpAddrEntry
SEQUENCE
	rcIpMplsTunnelHopToIpAddrMapHopName	DisplayString
	rcIpMplsTunnelHopToIpAddrMapIPAddr	IpAddress
	rcIpMplsTunnelHopToIpAddrMapIPAddrPrefixLen	INTEGER
	rcIpMplsTunnelHopToIpAddrMapRowStatus	RowStatus

RcIpMplsLspEntry
SEQUENCE
	rcIpMplsLspTunnelIndex	INTEGER
	rcIpMplsLspId	INTEGER
	rcIpMplsLspIngressLsrId	MplsLsrId
	rcIpMplsLspEgressLsrId	MplsLsrId
	rcIpMplsLspName	DisplayString
	rcIpMplsLspType	INTEGER
	rcIpMplsLspDetour	TruthValue
	rcIpMplsLspIncomingInterface	InterfaceIndex
	rcIpMplsLspIncomingLabel	Integer32
	rcIpMplsLspOutgoingInterface	InterfaceIndex
	rcIpMplsLspOutgoingLabel	Integer32

Defined Values

rcIpMplsMib		1.3.6.1.4.1.2272.1.8.102.0
Enterprise MIB for the Accelar product family.
MODULE-IDENTITY

rcIpMplsGlobalGroup		1.3.6.1.4.1.2272.1.8.102.1
OBJECT IDENTIFIER

rcIpMplsGlobalAdminStatus		1.3.6.1.4.1.2272.1.8.102.1.1
Disable or Enable MPLS globally
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpMplsGlobalRouterId		1.3.6.1.4.1.2272.1.8.102.1.2
IP address of the interface to be used as router-id
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcIpMplsGlobalAutomaticBeLsp		1.3.6.1.4.1.2272.1.8.102.1.3
Flag to control automatic generation of next hop LSP.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpMplsGlobalLspMerge		1.3.6.1.4.1.2272.1.8.102.1.4
Not used in this release.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpMplsGlobalDiffServDef		1.3.6.1.4.1.2272.1.8.102.1.5
Not used in this release.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpMplsGlobalTtl		1.3.6.1.4.1.2272.1.8.102.1.6
To set the time to live in hops when IP packets are being encapsulated in MPLS
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..255

rcIpMplsGlobalLabelMgmtFlag		1.3.6.1.4.1.2272.1.8.102.1.7
To set the time to live in hops when IP packets are being encapsulated in MPLS
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpMplsGlobalSessionMgmtFlag		1.3.6.1.4.1.2272.1.8.102.1.8
To set the time to live in hops when IP packets are being encapsulated in MPLS
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpMplsGlobalLspMgmtFlag		1.3.6.1.4.1.2272.1.8.102.1.9
To set the time to live in hops when IP packets are being encapsulated in MPLS
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpMplsGlobalTrafficControlFlag		1.3.6.1.4.1.2272.1.8.102.1.10
To set the time to live in hops when IP packets are being encapsulated in MPLS
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpMplsGlobalInactiveLspRestartTime		1.3.6.1.4.1.2272.1.8.102.1.11
Timer to initiate setting up a tunnel that previously failed.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

rcIpMplsGlobalInactiveLspRestartCount		1.3.6.1.4.1.2272.1.8.102.1.12
This parameter - if set to some non-zero (1-255) value, after that many failed trial of initiating a tunnel it will stop re-trying. But if set to 0(zero) it will keep on trying as before. The default value is 0(zero) for backward compatability.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

rcIpMplsInterfaceTableSize		1.3.6.1.4.1.2272.1.8.102.2
Size of Mpls Interface Table
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpMplsInterfaceTable		1.3.6.1.4.1.2272.1.8.102.3
Table of configured Mpls Interfaces.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpMplsInterfaceEntry

rcIpMplsInterfaceEntry		1.3.6.1.4.1.2272.1.8.102.3.1
An entry of rcIpMpls Interfaces In Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpMplsInterfaceEntry

rcIpMplsInterfaceIndex		1.3.6.1.4.1.2272.1.8.102.3.1.1
Interface index for the IP interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpMplsInterfaceLay3Addr		1.3.6.1.4.1.2272.1.8.102.3.1.2
Layer 3 address for the MPLS interface.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcIpMplsInterfaceLay3Mask		1.3.6.1.4.1.2272.1.8.102.3.1.3
Layer 3 mask for the MPLS interface.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcIpMplsInterfaceAdminStatus		1.3.6.1.4.1.2272.1.8.102.3.1.4
Indicates whether the MPLS interface is enabled or not.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpMplsInterfaceIndLblDistMode		1.3.6.1.4.1.2272.1.8.102.3.1.5
Indicates if the label distribution mode is independent or ordered.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	independent(1), ordered(2)

rcIpMplsInterfaceConsLblRetenMode		1.3.6.1.4.1.2272.1.8.102.3.1.6
Indicates if conservative or liberal retention mode is used for the MPLS interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	conservative(1), liberal(2)

rcIpMplsInterfaceImdLblUseMode		1.3.6.1.4.1.2272.1.8.102.3.1.7
Indicates what label-use-mode is used by the MPLS interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	immediate(1), notImmediate(2)

rcIpMplsInterfaceNoRouteReqRetryMode		1.3.6.1.4.1.2272.1.8.102.3.1.8
Not used in this release.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpMplsInterfacePenultimatePopRequest		1.3.6.1.4.1.2272.1.8.102.3.1.9
Flag to indicate whether to give implicit NULL labels for local networks.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpMplsInterfacePropogateLabelReleaseRequest		1.3.6.1.4.1.2272.1.8.102.3.1.10
Not used in this release.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpMplsInterfaceLabelRequestMode		1.3.6.1.4.1.2272.1.8.102.3.1.11
Indicates the label requiest mode used by the MPLS interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	requestNever(1), requestWhenNeeded(2), requestOnRequest(3)

rcIpMplsInterfaceOnDemandAdvMode		1.3.6.1.4.1.2272.1.8.102.3.1.12
Indicates the label advertise mode used by the MPLS interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	downstreamOnDemand(1), downstreamUnsolicited(2)

rcIpMplsInterfaceMtu		1.3.6.1.4.1.2272.1.8.102.3.1.13
Not used in this release.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	64..1518

rcIpMplsInterfaceLabelProtocol		1.3.6.1.4.1.2272.1.8.102.3.1.14
Indicates the label protocol used by the interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ldp(1), rsvp(2), both(3)

rcIpMplsInterfaceTraceFlag		1.3.6.1.4.1.2272.1.8.102.3.1.15
Flag used for tracing.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpMplsInterfaceRowStatus		1.3.6.1.4.1.2272.1.8.102.3.1.16
Row Status for create/delete
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpMplsRsvpGroup		1.3.6.1.4.1.2272.1.8.102.4
OBJECT IDENTIFIER

rcIpMplsRsvpAdminStatus		1.3.6.1.4.1.2272.1.8.102.4.1
State of global RSVP - enabled or disabled
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpMplsRsvpPathUpdateTime		1.3.6.1.4.1.2272.1.8.102.4.2
Time interval in seconds to update PATH soft states
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	2..65535

rcIpMplsRsvpResvUpdateTime		1.3.6.1.4.1.2272.1.8.102.4.3
Time interval in seconds to update RESV soft states
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	2..65535

rcIpMplsRsvpHelloTime		1.3.6.1.4.1.2272.1.8.102.4.4
Time interval in milli-seconds to send hello message
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	2..60

rcIpMplsRsvpBlockStateAgingTime		1.3.6.1.4.1.2272.1.8.102.4.5
PSB blockade state aging time in seconds
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	2..65535

rcIpMplsRsvpMaxBundleMsgSize		1.3.6.1.4.1.2272.1.8.102.4.6
Maximum BUNDLE message size
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

rcIpMplsRsvpMaxBundleMsgTime		1.3.6.1.4.1.2272.1.8.102.4.7
Maximum time in milli-seconds for an outgoing RSVP message to wait before being sent in the outgoing BUNDLE message
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	2..65535

rcIpMplsRsvpMaxAckMsgTime		1.3.6.1.4.1.2272.1.8.102.4.8
Maximum time in milli-seconds for an outgoing RSVP MESSAGE_ID_ACK/ RSVP MESSAGE_ID_NACK object to wait before being sent as a piggy-back in an unrelated RSVP message or in a separate ACK message
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	2..65535

rcIpMplsRsvpMaxAckMsgs		1.3.6.1.4.1.2272.1.8.102.4.9
Maximum number of RSVP MESSAGE_ID_ACK/ RSVP MESSAGE_ID_NACK objects to be sent in a single RSVP ACK message
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

rcIpMplsRsvpMaxMsgIdListSize		1.3.6.1.4.1.2272.1.8.102.4.10
Maximum size of MESSAGE_ID_LIST object in MESSAGE_IDs
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

rcIpMplsRsvpMaxMsgIdListTime		1.3.6.1.4.1.2272.1.8.102.4.11
Maximum time in milli-seconds for an outgoing RSVP refresh message to wait before being sent out
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	2..65535

rcIpMplsRsvpMaxPiggyBackMsgAcks		1.3.6.1.4.1.2272.1.8.102.4.12
Maximum number of RSVP MESSAGE_ID_ACK/ RSVP MESSAGE_ID_NACK objects to be piggy-backed on a single RSVP non-ACK message
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

rcIpMplsRsvpPathAgingTimeMult		1.3.6.1.4.1.2272.1.8.102.4.13
PATH soft state aging time multiplier - how many times to miss PATH refresh before considering PSB aged out
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	2..255

rcIpMplsRsvpResvAgingTimeMult		1.3.6.1.4.1.2272.1.8.102.4.14
RESV soft state aging time multiplier - how many times to miss RESV refresh before considering RSB filterspec aged out
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	2..255

rcIpMplsRsvpHelloAgingTimeMult		1.3.6.1.4.1.2272.1.8.102.4.15
Hello aging time multiplier - how many times to miss Hello/HelloAck message before considering link down
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	2..255

rcIpMplsRsvpPathVectorLimit		1.3.6.1.4.1.2272.1.8.102.4.16
Path vector limit
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	2..255

rcIpMplsRsvpHopCountLimit		1.3.6.1.4.1.2272.1.8.102.4.17
Maximum hop count
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	2..255

rcIpMplsRsvpRapidRetransTime		1.3.6.1.4.1.2272.1.8.102.4.18
Initial rapid re-transmission time in milli-seconds
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	2..65535

rcIpMplsRsvpRapidRetransIncrement		1.3.6.1.4.1.2272.1.8.102.4.19
Rapid re-transmission increment
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	2..255

rcIpMplsRsvpRapidRetransLimit		1.3.6.1.4.1.2272.1.8.102.4.20
Maximum number of attempts to re-transmit message
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	2..255

rcIpMplsRsvpReqResvConfFlag		1.3.6.1.4.1.2272.1.8.102.4.21
Require RSVP ResvConf message on successful reservations
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpMplsRsvpPathRemoveFlag		1.3.6.1.4.1.2272.1.8.102.4.22
Enable Path_State_Removed flag using in ERROR_SPEC object of PATH_ERR message
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpMplsRsvpProtectDomainFlag		1.3.6.1.4.1.2272.1.8.102.4.23
Protection Domain support
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpMplsRsvpPathTraceFlag		1.3.6.1.4.1.2272.1.8.102.4.24
enable PATH direction tracing
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpMplsRsvpResvTraceFlag		1.3.6.1.4.1.2272.1.8.102.4.25
enable RESV direction tracing
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpMplsRsvpTrafficControlTraceFlag		1.3.6.1.4.1.2272.1.8.102.4.26
enable traffic control tracing
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpMplsRsvpSessionTraceFlag		1.3.6.1.4.1.2272.1.8.102.4.27
enable session management tracing
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpMplsLdpGroup		1.3.6.1.4.1.2272.1.8.102.5
OBJECT IDENTIFIER

rcIpMplsLdpAdminStatus		1.3.6.1.4.1.2272.1.8.102.5.1
Indicates qhetehr global LDP is enabled or disabled.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpMplsLdpHoldTime		1.3.6.1.4.1.2272.1.8.102.5.2
Keep alive time for LDP peers.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	15..65535

rcIpMplsLdpHelloHoldTime		1.3.6.1.4.1.2272.1.8.102.5.3
Time for receiving link hello messages from peer.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	15..65535

rcIpMplsLdpHelloInterval		1.3.6.1.4.1.2272.1.8.102.5.4
Frequency of sending hello messages to peer.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

rcIpMplsLdpMaxHops		1.3.6.1.4.1.2272.1.8.102.5.5
Maximum number of LSP hops for setting up an LSP.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..255

rcIpMplsLdpPathVectorLimit		1.3.6.1.4.1.2272.1.8.102.5.6
Max hop count for loop detection.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..32

rcIpMplsLdpTgtHelloHoldTime		1.3.6.1.4.1.2272.1.8.102.5.7
Time for receiving targetted link hello messages.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	15..65535

rcIpMplsLdpLoopDetFlag		1.3.6.1.4.1.2272.1.8.102.5.8
Flag to set loop detection capability.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpMplsLdpLblMergeFlag		1.3.6.1.4.1.2272.1.8.102.5.9
Not used in this release.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpMplsLdpAuthFlag		1.3.6.1.4.1.2272.1.8.102.5.10
Not used in this release.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpMplsLdpInterfaceTableSize		1.3.6.1.4.1.2272.1.8.102.6
Size of Mpls LDP Interface Table
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpMplsLdpInterfaceTable		1.3.6.1.4.1.2272.1.8.102.7
Table of configured Mpls LDP Interfaces.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpMplsLdpInterfaceEntry

rcIpMplsLdpInterfaceEntry		1.3.6.1.4.1.2272.1.8.102.7.1
An entry of rcIpMpls LDP Interfaces In Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpMplsLdpInterfaceEntry

rcIpMplsLdpInterfaceIndex		1.3.6.1.4.1.2272.1.8.102.7.1.1
Interface index for LDP interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpMplsLdpInterfaceLay3Addr		1.3.6.1.4.1.2272.1.8.102.7.1.2
Layer 3 address of LDP interface.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcIpMplsLdpInterfaceLay3Mask		1.3.6.1.4.1.2272.1.8.102.7.1.3
Layer3 mask for LDP interface.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcIpMplsLdpInterfaceTargetHelloFlag		1.3.6.1.4.1.2272.1.8.102.7.1.4
Flag for enabling target hellos.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpMplsLdpInterfaceTargetResponseFlag		1.3.6.1.4.1.2272.1.8.102.7.1.5
Flag to enable target response messgaes.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpMplsLdpInterfaceNonTtlLspFlag		1.3.6.1.4.1.2272.1.8.102.7.1.6
Not used in this release.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpMplsLdpInterfaceRowStatus		1.3.6.1.4.1.2272.1.8.102.7.1.7
Row status for the LDP interface.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpMplsRsvpInterfaceTableSize		1.3.6.1.4.1.2272.1.8.102.8
Size of Mpls RSVP Interface Table
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpMplsRsvpInterfaceTable		1.3.6.1.4.1.2272.1.8.102.9
Table of configured Mpls RSVP Interfaces.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpMplsRsvpInterfaceEntry

rcIpMplsRsvpInterfaceEntry		1.3.6.1.4.1.2272.1.8.102.9.1
An entry of rcIpMpls RSVP Interfaces In Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpMplsRsvpInterfaceEntry

rcIpMplsRsvpInterfaceIndex		1.3.6.1.4.1.2272.1.8.102.9.1.1
Index for RSVP interface table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpMplsRsvpInterfaceLay3Addr		1.3.6.1.4.1.2272.1.8.102.9.1.2
Layer 3 address for RSVP interface.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcIpMplsRsvpInterfaceLay3Mask		1.3.6.1.4.1.2272.1.8.102.9.1.3
Layer 3 mask for RSVP interface.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcIpMplsRsvpInterfaceAuthFlag		1.3.6.1.4.1.2272.1.8.102.9.1.4
Not used in this release.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpMplsRsvpInterfaceHelloFlag		1.3.6.1.4.1.2272.1.8.102.9.1.5
Flag to enable RSVP interface hello.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpMplsRsvpInterfaceRefreshReductionFlag		1.3.6.1.4.1.2272.1.8.102.9.1.6
Not used in this release.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpMplsRsvpInterfaceMemoryReductionFlag		1.3.6.1.4.1.2272.1.8.102.9.1.7
Not used in this release.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpMplsRsvpInterfaceReliableFlag		1.3.6.1.4.1.2272.1.8.102.9.1.8
Not used in this release.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpMplsRsvpInterfaceEPolicingFlag		1.3.6.1.4.1.2272.1.8.102.9.1.9
Not used in this release.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpMplsRsvpInterfaceRowStatus		1.3.6.1.4.1.2272.1.8.102.9.1.10
Row status for RSVP interface.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpMplsLdpTargetAddrTableSize		1.3.6.1.4.1.2272.1.8.102.10
Size of Mpls LDP target address Table
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpMplsLdpTargetAddrTable		1.3.6.1.4.1.2272.1.8.102.11
Table of configured Mpls LDP target addresses.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpMplsLdpTargetAddrEntry

rcIpMplsLdpTargetAddrEntry		1.3.6.1.4.1.2272.1.8.102.11.1
An entry of rcIpMpls LDP target addresses In Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpMplsLdpTargetAddrEntry

rcIpMplsLdpTargetAddrBaseAddr		1.3.6.1.4.1.2272.1.8.102.11.1.1
The LDP interface IP address for which target address should be configured
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcIpMplsLdpTargetAddrTgtAddr		1.3.6.1.4.1.2272.1.8.102.11.1.2
The IP address configured to be the LDP target address
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcIpMplsLdpTargetAddrRowStatus		1.3.6.1.4.1.2272.1.8.102.11.1.3
Row Status for LDP target address table.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpMplsTunnelGroupTable		1.3.6.1.4.1.2272.1.8.102.12
Table of Tunnel Groups.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpMplsTunnelGroupEntry

rcIpMplsTunnelGroupEntry		1.3.6.1.4.1.2272.1.8.102.12.1
An entry of rcIpMpls tunnel group In Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpMplsTunnelGroupEntry

rcIpMplsTunnelGroupId		1.3.6.1.4.1.2272.1.8.102.12.1.1
Tunnel Group Identifier
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

rcIpMplsTunnelGroupDestAddr		1.3.6.1.4.1.2272.1.8.102.12.1.2
Group the tunnels with same destination IP address into the tunnel group
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcIpMplsTunnelGroupPrimaryTunnel		1.3.6.1.4.1.2272.1.8.102.12.1.3
List of primary tunnels contained in the tunnel group, diplayed in the format of /[,/]
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rcIpMplsTunnelGroupActiveTunnel		1.3.6.1.4.1.2272.1.8.102.12.1.4
Active tunnel id in the Tunnel Group
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

rcIpMplsTunnelGroupPersistentFlag		1.3.6.1.4.1.2272.1.8.102.12.1.5
Tunnel Group Persistent Flag
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpMplsTunnelGroupOperation		1.3.6.1.4.1.2272.1.8.102.12.1.6
Add tunnel to the Tunnel Group or remove tunnel from the tunnel group
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), addTunnel(1), remTunnel(2)

rcIpMplsTunnelGroupTunnelList		1.3.6.1.4.1.2272.1.8.102.12.1.7
List of Tunnels contained in the tunnel group, diplayed in the format of /[,/], such as string 2,4,5 indicated the tunnel group contains tunnel 2, tunnel 4, and tunnel 5
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rcIpMplsTunnelGroupFtnList		1.3.6.1.4.1.2272.1.8.102.12.1.8
List of fecs bineded to the tunnel group, the display format is same as rcIpMplsTunnelGroupTunnelList
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

rcIpMplsTunnelGroupBgpNeighbor		1.3.6.1.4.1.2272.1.8.102.12.1.9
BGP neigbors associated with the tunnel group
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpMplsTunnelGroupRowStatus		1.3.6.1.4.1.2272.1.8.102.12.1.10
Row status for create/delete the tunnel group.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpMplsTunnelGroupBackupTunnel		1.3.6.1.4.1.2272.1.8.102.12.1.11
Backup tunnel id in the Tunnel Group displayed in the format
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rcIpMplsTeGroup		1.3.6.1.4.1.2272.1.8.102.13
OBJECT IDENTIFIER

rcIpMplsTeFloodThresholdStart		1.3.6.1.4.1.2272.1.8.102.13.1
First TE flooding threshold for significant bandwidth change in percent.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..100

rcIpMplsTeFloodThresholdDelta		1.3.6.1.4.1.2272.1.8.102.13.2
Delta TE flooding threshold for significant Bandwidth change in percent. After start threshold is hit every delta change in link bandwidth results in flooding link's TE information.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..100

rcIpMplsTeInterfaceTable		1.3.6.1.4.1.2272.1.8.102.14
rcIpMplsInterface Traffic-Eng table. This table contains rows which are traffic-eng configuration parameters for the link.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpMplsTeInterfaceEntry

rcIpMplsTeInterfaceEntry		1.3.6.1.4.1.2272.1.8.102.14.1
An entry of rcIpMplsInterface Te Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpMplsTeInterfaceEntry

rcIpMplsTeInterfaceIndex		1.3.6.1.4.1.2272.1.8.102.14.1.1
Interface index for the IP interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpMplsTeInterfaceLay3Addr		1.3.6.1.4.1.2272.1.8.102.14.1.2
Layer 3 address for the MPLS interface.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpMplsTeInterfaceLay3Mask		1.3.6.1.4.1.2272.1.8.102.14.1.3
Layer 3 mask for the MPLS interface.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpMplsTeInterfaceIgp		1.3.6.1.4.1.2272.1.8.102.14.1.4
Traffic-eng IGP protocol to use on link.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), ospf(1)

rcIpMplsTeInterfaceMetric		1.3.6.1.4.1.2272.1.8.102.14.1.5
Traffic-eng metric to assign to the link.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..2147483647

rcIpMplsTeInterfaceMaxBandwidth		1.3.6.1.4.1.2272.1.8.102.14.1.6
Maximum bandwidth on the link in bits/sec in the direction outwards from the local system.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..2147483647

rcIpMplsTeInterfaceMaxReservableBandwidth		1.3.6.1.4.1.2272.1.8.102.14.1.7
Maximum reservable bandwidth on the link in bits/sec in the direction outwards from the local system.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..2147483647

rcIpMplsTeInterfaceResourceColor		1.3.6.1.4.1.2272.1.8.102.14.1.8
Resource class/color which represents administrative group membership for the link. The integer value represents the format of a hexadecimal 32-bit mask. A link that is a member of more than one administrative group will have multiple mask bits set.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(4)

rcIpMplsTunnelTable		1.3.6.1.4.1.2272.1.8.102.15
Table of Tunnels with label record info .
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpMplsTunnelEntry

rcIpMplsTunnelEntry		1.3.6.1.4.1.2272.1.8.102.15.1
An entry of rcIpMpls tunnel In Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpMplsTunnelEntry

rcIpMplsTunnelId		1.3.6.1.4.1.2272.1.8.102.15.1.1
Tunnel Identifier
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

rcIpMplsTunnelLabelRecordFlag		1.3.6.1.4.1.2272.1.8.102.15.1.2
Tunnel Identifier
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpMplsTunnelRowStatus		1.3.6.1.4.1.2272.1.8.102.15.1.3
Creation or deletion of row
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpMplsTunnelExtTable		1.3.6.1.4.1.2272.1.8.102.16
The mplsTunnelExtTable provides enterprise extension options for a mplsTunnelEntry that has be created for a MPLS tunnel. The mplsTunnelEntry must be created apriori.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpMplsTunnelExtEntry

rcIpMplsTunnelExtEntry		1.3.6.1.4.1.2272.1.8.102.16.1
An entry of rcIpMpls Tunnel Ext Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpMplsTunnelExtEntry

rcIpMplsTunnelExtIndex		1.3.6.1.4.1.2272.1.8.102.16.1.1
Uniquely identifies this row. This an index object for the mplsTunnelExtTable entry that in part also specifies the mpls tunnel entry with which this tunnel extension entry is associated. The value of this object should mimic the value of mplsTunnelIndex of the MplsTunnelEntry of the mpls tunnel for which this extended tunnel table entry row is to be applied.
Status: current	Access: read-only
OBJECT-TYPE
	MplsTunnelIndex

rcIpMplsTunnelExtInstance		1.3.6.1.4.1.2272.1.8.102.16.1.2
Uniquely identifies an instance of a tunnel's extended entry. This an index object for the mplsTunnelExtTable entry that in part specifies the mpls tunnel with which this tunnel extension entry is associated. Uniquely The value of this object should be equal to the value of MplsTunnelInstance of the MplsTunnelEntry of the mpls tunnel for which this extended tunnel table row is to be applied.
Status: current	Access: read-only
OBJECT-TYPE
	MplsTunnelInstanceIndex

rcIpMplsTunnelExtEgressLSRId		1.3.6.1.4.1.2272.1.8.102.16.1.3
The purpose of this object is to uniquely identity a tunnel within a network to which this extended tunnel table entry should apply. This an index object for the mplsTunnelExtTable entry that in part specifies the mpls tunnel with which this tunnel extension entry is associated. The value of this object should mimic the value of mplsTunnelIngressLSRId of the MplsTunnelEntry of the mpls tunnel for which this extended tunnel table row is to be applied. Please reference mplsTunnelIngressLSRId for additional information on it which is mimiced here.
Status: current	Access: read-only
OBJECT-TYPE
	MplsLsrId

rcIpMplsTunnelExtIngressLSRId		1.3.6.1.4.1.2272.1.8.102.16.1.4
Specifies the egress LSR id for which this extended tunnel table entry should apply. This is an index object for the mplsTunnelExtTable entry that in part specifies the mpls tunnel with which this tunnel extension entry is associated. The value of this object should mimic the value of mplsTunnelEngressLSRId of the MplsTunnelEntry of the mpls tunnel for which this extended tunnel table row is to be applied.
Status: current	Access: read-only
OBJECT-TYPE
	MplsLsrId

rcIpMplsTunnelExtFrrTableIndex		1.3.6.1.4.1.2272.1.8.102.16.1.5
Index into the mplsTunnelFrrTable entry that specifies the frr path to use for the tunnel that implied by the index objects of this row entry. Specifying a frr path to use is optional.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0..2147483647

rcIpMplsTunnelExtRowStatus		1.3.6.1.4.1.2272.1.8.102.16.1.6
This variable is used to create, modify, and/or delete a row in this table.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpMplsTunnelFrrTable		1.3.6.1.4.1.2272.1.8.102.17
The rcIpMplsTunnelFrrTable is used to indicate the frr constraints for a frr detour LSP for a tunnel specified as row entry in the mplsTunnelTable.The frr constraints are established viasignaling, for the outgoing direction of the tunnel. Each row in this table is indexed by rcIpMplsTunnelFrrListIndex. In this implementation it is intended that one row entry may used as a frr template for multiple tunnels. Conversely a row entry may be created for each tunnel, or there may be a combination of both styles, one to one, and one to many in the relationship between a row entry of this table and tunnel(s).
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpMplsTunnelFrrEntry

rcIpMplsTunnelFrrEntry		1.3.6.1.4.1.2272.1.8.102.17.1
An entry in this table represents a tunnel frr path. An entry is created by a network administrator for signaled LSP with frr path set up by an MPLS signaling proto col.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpMplsTunnelFrrEntry

rcIpMplsTunnelFrrListIndex		1.3.6.1.4.1.2272.1.8.102.17.1.1
Primary index into this table identifying a particular row entry of frr detour LSP contraints.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	1..65535

rcIpMplsTunnelFrrSetupPrio		1.3.6.1.4.1.2272.1.8.102.17.1.2
Setup priority for frr detour LSP.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..7

rcIpMplsTunnelFrrHoldingPrio		1.3.6.1.4.1.2272.1.8.102.17.1.3
Holding priority for frr detour LSP.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..7

rcIpMplsTunnelFrrHopLimit		1.3.6.1.4.1.2272.1.8.102.17.1.4
Maximum number of hops a frr detour LSP is allowed to traverse.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

rcIpMplsTunnelFrrBandwidth		1.3.6.1.4.1.2272.1.8.102.17.1.5
Bandwidth estimate with which to set up the frr detour LSPs in units of a million bits per second (Mbps).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..1000

rcIpMplsTunnelFrrProtectionType		1.3.6.1.4.1.2272.1.8.102.17.1.6
Frr backup or resource protection type to be used.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	oneToOneBackup(0), facilityBackup(1)

rcIpMplsTunnelFrrExclAnyAffinity		1.3.6.1.4.1.2272.1.8.102.17.1.7
Exclude any link in detour LSP setup which is represented by administratively defined attributes associated with the bit pattern of this object. The value represents the format of a hexadecimal 32-bit vector or mask.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(4)

rcIpMplsTunnelFrrInclAnyAffinity		1.3.6.1.4.1.2272.1.8.102.17.1.8
Allow detour LSP setup on any link which is represented by administratively defined attributes associated with the bit pattern of this object. The value represents the format of a hexadecimal 32-bit vector or mask. A value of zero allows a detour LSP to be setup on any link per the constraint of thi s object.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(4)

rcIpMplsTunnelFrrInclAllAffinity		1.3.6.1.4.1.2272.1.8.102.17.1.9
Only allow detour LSP setup on links which contain at a minimum the administratively defined attributes represented by this bit pattern. The value represents the format of a hexadecimal 32-bit vector or mask. A value of zero allows a detour LSP to be setup on any link per the constraint of thi s object.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(4)

rcIpMplsTunnelFrrLegacyFlag		1.3.6.1.4.1.2272.1.8.102.17.1.10
Flag to control the format of the frr object used. When set to true, the legacy format is used which is a class type of 7. When set to false the frr format used is for class type of 1.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpMplsTunnelFrrRowStatus		1.3.6.1.4.1.2272.1.8.102.17.1.11
This variable is used to create, modify, and/or delete a row in this table.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpMplsTunnelHopToIpAddrMapTable		1.3.6.1.4.1.2272.1.8.102.18
The rcIpMplsTunnelHopToIpAddrMapTable is used to maintain mapping between Hop name and IP Address.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpMplsTunnelHopToIpAddrEntry

rcIpMplsTunnelHopToIpAddrMapEntry		1.3.6.1.4.1.2272.1.8.102.18.1
An entry in this table represents a mapping between Hop name and the IP Address.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpMplsTunnelHopToIpAddrEntry

rcIpMplsTunnelHopToIpAddrMapHopName		1.3.6.1.4.1.2272.1.8.102.18.1.1
Primary index into this table identifying a hop name.
Status: current	Access: not-accessible
OBJECT-TYPE
	DisplayString

rcIpMplsTunnelHopToIpAddrMapIPAddr		1.3.6.1.4.1.2272.1.8.102.18.1.2
Table column, identifying an IP Address.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

rcIpMplsTunnelHopToIpAddrMapIPAddrPrefixLen		1.3.6.1.4.1.2272.1.8.102.18.1.3
Table column identifying IP Address prefix length.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..32

rcIpMplsTunnelHopToIpAddrMapRowStatus		1.3.6.1.4.1.2272.1.8.102.18.1.4
Row status.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcIpMplsLspTable		1.3.6.1.4.1.2272.1.8.102.19
Table of originated, terminated and transit operational LSPs with all cross connect information
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpMplsLspEntry

rcIpMplsLspEntry		1.3.6.1.4.1.2272.1.8.102.19.1
An entry of rcIpMpls Lsp in Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpMplsLspEntry

rcIpMplsLspTunnelIndex		1.3.6.1.4.1.2272.1.8.102.19.1.1
Tunnel Index
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..65535

rcIpMplsLspId		1.3.6.1.4.1.2272.1.8.102.19.1.2
LSP ID
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..65535

rcIpMplsLspIngressLsrId		1.3.6.1.4.1.2272.1.8.102.19.1.3
Specifies the Ingress LSR Id
Status: current	Access: not-accessible
OBJECT-TYPE
	MplsLsrId

rcIpMplsLspEgressLsrId		1.3.6.1.4.1.2272.1.8.102.19.1.4
Specifies the Egress LSR Id
Status: current	Access: not-accessible
OBJECT-TYPE
	MplsLsrId

rcIpMplsLspName		1.3.6.1.4.1.2272.1.8.102.19.1.5
LSP Name
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

rcIpMplsLspType		1.3.6.1.4.1.2272.1.8.102.19.1.6
This value signifies the role that this tunnel entry/instance represents. This value MUST be set to head(1) at the originating point of the tunnel. This value MUST be set to transit(2) at transit points along the tunnel, if transit points are supported. This value MUST be set to tail(3) at the terminating point of the tunnel if tunnel tails are supported.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	head(1), transit(2), tail(3)

rcIpMplsLspDetour		1.3.6.1.4.1.2272.1.8.102.19.1.7
The tunnel is a detour tunnel or not
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcIpMplsLspIncomingInterface		1.3.6.1.4.1.2272.1.8.102.19.1.8
LSR-assigned ifIndex
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcIpMplsLspIncomingLabel		1.3.6.1.4.1.2272.1.8.102.19.1.9
Incoming Label value
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpMplsLspOutgoingInterface		1.3.6.1.4.1.2272.1.8.102.19.1.10
LSR-assigned ifIndex
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcIpMplsLspOutgoingLabel		1.3.6.1.4.1.2272.1.8.102.19.1.11
Outgoing Label value
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor