RAPID-CITY

File: RAPID-CITY.mib (2671303 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-TC	RFC1155-SMI
RFC1213-MIB	SNMPv2-CONF	ATM-TC-MIB
INET-ADDRESS-MIB	IPV6-TC	IGMP-STD-MIB
DVMRP-MIB	VRRP-MIB	SNMP-FRAMEWORK-MIB
DIFFSERV-MIB	MPLS-TC-STD-MIB	BGP4-MIB
MSDP-MIB

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	TEXTUAL-CONVENTION
enterprises	IpAddress	TimeTicks
Counter	DisplayString	RowStatus
TruthValue	MacAddress	DateAndTime
TimeStamp	RowPointer	TimeInterval
Gauge32	Integer32	NOTIFICATION-TYPE
Unsigned32	Counter32	Counter64
StorageType	MODULE-COMPLIANCE	OBJECT-GROUP
AtmAddr	PhysAddress	ifIndex
InetAddressType	InetAddress	InetAddressPrefixLength
InetPortNumber	InetAutonomousSystemNumber	Ipv6IfIndex
Ipv6Address	Ipv6AddressPrefix	Ipv6AddressIfIdentifier
Ipv6IfIndexOrZero	ifAdminStatus	ifOperStatus
igmpInterfaceIfIndex	igmpInterfaceQuerier	dvmrpInterfaceIfIndex
dvmrpNeighborIfIndex	dvmrpNeighborAddress	dvmrpInterfaceOperState
igmpCacheAddress	igmpCacheIfIndex	ipNetToMediaNetAddress
ipNetToMediaPhysAddress	VrId	SnmpAdminString
SnmpSecurityLevel	SnmpSecurityModel	IndexInteger
MplsTunnelIndex	MplsLabel	MplsExtendedTunnelId
MplsTunnelInstanceIndex	MplsLdpIdentifier	MplsLSPID
bgpPeerRemoteAddr	bgpPeerLastError	bgpPeerState
msdpPeerFsmEstablishedTransitions	msdpPeerState	msdpPeerEntry
msdpSACacheEntry

Defined Types

BridgeId
An identifier that identifies the Bridge Id
TEXTUAL-CONVENTION
	OCTET STRING	Size(8)

Timeout
An identifier that identifies the timeout value.
TEXTUAL-CONVENTION
	Integer32

EnableValue
Enable/Disable value.
TEXTUAL-CONVENTION
	INTEGER	enable(1), disable(2)

RcLongDisplayString
The semantics are identical to the standard DisplayString in RFC1213 and RFC2579, except for the longer length that is allowed with this TC.
TEXTUAL-CONVENTION
	OCTET STRING	Size(0..65535)

InterfaceIndex
Port IfIndex.
TEXTUAL-CONVENTION
	Integer32

InterfaceIndexOrZero
This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits the additional value of zero. the value zero is object-specific and must therefore be defined as part of the description of any object which uses this syntax. Examples of the usage of zero might include situations where interface was unknown, or when none or all interfaces need to be referenced.
TEXTUAL-CONVENTION
	Integer32	0..2147483647

PortSet
The string is 88 octets long, for a total of 704 bits. Each bit corresponds to a port, as represented by its ifIndex value . When a bit has the value one(1), the corresponding port is a member of the set. When a bit has the value zero(0), the corresponding port is not a member of the set. The encoding is such that the most significant bit of octet #1 corresponds to ifIndex 0, while the least significant bit of octet #88 corresponds to ifIndex 703. In order to accommodate future uses of this the string has a max size of 255 bytes.
TEXTUAL-CONVENTION
	OCTET STRING	Size(0..255)

IdList
An identifier for a list of Ids.
TEXTUAL-CONVENTION
	OCTET STRING

VrfIdentifier
Virtual Router Identifier. VRFID 0 is reserved for the Administrative VRF and cannot be used to create VRF's.
TEXTUAL-CONVENTION
	Unsigned32	0..4294967295

Ipv6NextHdr
The ipv6 next header to look for.
TEXTUAL-CONVENTION
	INTEGER	hop-by-hop(0), icmpv4(1), igmpv4(2), ipInIp(4), tcp(6), egp(8), udp(17), ipv6(41), routing(43), frag(44), rsvp(46), ipsecESP(50), ipsecAh(51), icmpv6(58), noNxtHdr(59), destOptions(60), undefined(255)

KhiStatusValue
Key Health Indication status defintion green(1): normal status. yellow(2): Alert. red(3): critical state. adminDisable(4): administately disable. notApplicable(5): either not config or not applicable
TEXTUAL-CONVENTION
	INTEGER	green(1), yellow(2), red(3), adminDisable(4), notApplicable(5)

RcSysTrapRecvEntry
SEQUENCE
	rcSysTrapRecvAddress	IpAddress
	rcSysTrapRecvVersion	INTEGER
	rcSysTrapRecvCommunity	DisplayString
	rcSysTrapRecvSrcAddress	IpAddress
	rcSysTrapRecvRowStatus	RowStatus

RcSysAccesspolicyEntry
SEQUENCE
	rcSysAccessPolicyId	INTEGER
	rcSysAccessPolicyName	DisplayString
	rcSysAccessPolicyPolicyEnable	TruthValue
	rcSysAccessPolicyMode	INTEGER
	rcSysAccessPolicyService	INTEGER
	rcSysAccessPolicyPrecedence	INTEGER
	rcSysAccessPolicyNetAddr	IpAddress
	rcSysAccessPolicyNetMask	IpAddress
	rcSysAccessPolicyTrustedHostAddr	IpAddress
	rcSysAccessPolicyTrustedHostUserName	DisplayString
	rcSysAccessPolicyAccessLevel	INTEGER
	rcSysAccessPolicyLog	TruthValue
	rcSysAccessPolicyUsage	Counter32
	rcSysAccessPolicyRowStatus	RowStatus
	rcSysAccessPolicyAccessStrict	TruthValue
	rcSysAccessPolicyNetInetAddrType	INTEGER
	rcSysAccessPolicyNetInetAddress	InetAddress
	rcSysAccessPolicyNetInetAddrPrefixLen	InetAddressPrefixLength
	rcSysAccessPolicyTrustedHostInetAddress	InetAddress

RcSysAccPolSnmpGrpEntry
SEQUENCE
	rcSysAccPolSnmpGrpName	SnmpAdminString
	rcSysAccPolSnmpGrpModel	SnmpSecurityModel
	rcSysAccPolSnmpGrpRowStatus	RowStatus

RcSysTrapSenderEntry
SEQUENCE
	rcSysTrapSenderRecvAddress	IpAddress
	rcSysTrapSenderSrcAddress	IpAddress

RcSysDnsServerListEntry
SEQUENCE
	rcSysDnsServerListType	INTEGER
	rcSysDnsServerListIp	IpAddress
	rcSysDnsServerListStatus	INTEGER
	rcSysDnsServerListRequestCount	Counter32
	rcSysDnsServerListSuccessCount	Counter32
	rcSysDnsServerListRowStatus	RowStatus
	rcSysDnsServerListAddressType	InetAddressType
	rcSysDnsServerListAddress	InetAddress

RcSysDnsHostEntry
SEQUENCE
	rcSysDnsHostData	OCTET STRING
	rcSysDnsHostName	OCTET STRING	Size(0..256)
	rcSysDnsHostIpAddress	IpAddress
	rcSysDnsHostSource	OCTET STRING	Size(0..256)
	rcSysDnsHostAddressType	InetAddressType
	rcSysDnsHostAddress	InetAddress

RcSysFrcMsgControlEntry
SEQUENCE
	rcSysFrcMsgControlPatternId	Integer32
	rcSysFrcMsgControlPattern	DisplayString
	rcSysFrcMsgControlRowStatus	RowStatus

RcVlanEntry
SEQUENCE
	rcVlanId	INTEGER
	rcVlanName	DisplayString
	rcVlanColor	INTEGER
	rcVlanHighPriority	TruthValue
	rcVlanRoutingEnable	TruthValue
	rcVlanIfIndex	InterfaceIndex
	rcVlanAction	INTEGER
	rcVlanResult	INTEGER
	rcVlanStgId	INTEGER
	rcVlanType	INTEGER
	rcVlanPortMembers	PortSet
	rcVlanActiveMembers	PortSet
	rcVlanStaticMembers	PortSet
	rcVlanNotAllowToJoin	PortSet
	rcVlanProtocolId	INTEGER
	rcVlanSubnetAddr	IpAddress
	rcVlanSubnetMask	IpAddress
	rcVlanAgingTime	INTEGER
	rcVlanMacAddress	MacAddress
	rcVlanRowStatus	RowStatus
	rcVlanIgmpSnoopEnable	TruthValue
	rcVlanIgmpSnoopReportProxyEnable	TruthValue
	rcVlanIgmpSnoopRobustness	INTEGER
	rcVlanIgmpSnoopQueryInterval	INTEGER
	rcVlanIgmpSnoopMRouterPorts	PortSet
	rcVlanUserDefinedPid	Integer32
	rcVlanIgmpSnoopActiveMRouterPorts	PortSet
	rcVlanProtocolIds	Integer32
	rcVlanIgmpSnoopActiveQuerier	IpAddress
	rcVlanIgmpSnoopMRouterExpiration	Integer32
	rcVlanIgmpSnoopQuerierPort	InterfaceIndex
	rcVlanUserPriority	INTEGER
	rcVlanQosLevel	INTEGER
	rcVlanTosValue	INTEGER
	rcVlanEncap	INTEGER
	rcVlanFirewallVlanType	INTEGER
	rcVlanFirewallClusterId	INTEGER
	rcVlanOspfPassivePortMember	PortSet
	rcVlanFdbAging	INTEGER
	rcVlanUnkDstMacDiscard	EnableValue
	rcVlanNlbMode	INTEGER
	rcVlanVrfId	VrfIdentifier
	rcVlanVrfName	DisplayString
	rcVlanNodalMepList	DisplayString
	rcVlanNumOfNodalMep	Integer32
	rcVlanNodalMipLevelList	DisplayString
	rcVlanNumOfNodalMipLevel	Integer32
	rcVlanIpMultinettingEnable	TruthValue
	rcVlanAssociatedIpMultinettingVlan	Integer32
	rcVlanPlsbIsid	Integer32

RcVlanPortEntry
SEQUENCE
	rcVlanPortIndex	Integer32
	rcVlanPortNumVlanIds	Integer32
	rcVlanPortVlanIds	IdList
	rcVlanPortType	INTEGER
	rcVlanPortDiscardTaggedFrames	TruthValue
	rcVlanPortDiscardUntaggedFrames	TruthValue
	rcVlanPortDefaultVlanId	INTEGER
	rcVlanPortPerformTagging	TruthValue
	rcVlanPortSVlanPortType	INTEGER
	rcVlanPortLoopDetect	TruthValue
	rcVlanPortFirstPortInOpid	InterfaceIndex
	rcVlanPortLastPortInOpid	InterfaceIndex
	rcVlanPortUntagDefaultVlan	TruthValue
	rcVlanPortLoopDetectAction	INTEGER
	rcVlanPortArpDetect	TruthValue
	rcVlanPortSpoofDetect	TruthValue
	rcVlanPortVlanIdList	OCTET STRING

RcVlanMacEntry
SEQUENCE
	rcVlanMacVlanId	Integer32
	rcVlanMacAddr	MacAddress
	rcVlanMacRowStatus	RowStatus

RcVlanIgmpSnoopEntry
SEQUENCE
	rcVlanIgmpSnoopVlanId	INTEGER
	rcVlanIgmpSnoopIpAddress	IpAddress
	rcVlanIgmpSnoopIfIndex	InterfaceIndex
	rcVlanIgmpSnoopMember	IpAddress
	rcVlanIgmpSnoopExpiration	Integer32
	rcVlanIgmpSnoopType	INTEGER

RcVlanIgmpSnoopStaticEntry
SEQUENCE
	rcVlanIgmpSnoopStaticVlanId	INTEGER
	rcVlanIgmpSnoopStaticIpAddress	IpAddress
	rcVlanIgmpSnoopStaticMemberPorts	PortSet
	rcVlanIgmpSnoopStaticRowStatus	RowStatus
	rcVlanIgmpSnoopStaticNotAllowedToJoin	PortSet

RcVlanIgmpSnoopAccessEntry
SEQUENCE
	rcVlanIgmpSnoopAccessVlanId	INTEGER
	rcVlanIgmpSnoopAccessGrpAddr	IpAddress
	rcVlanIgmpSnoopAccessHostAddr	IpAddress
	rcVlanIgmpSnoopAccessHostMask	IpAddress
	rcVlanIgmpSnoopAccessMode	INTEGER
	rcVlanIgmpSnoopAccessRowStatus	RowStatus

RcVlanIgmpSnoopSenderEntry
SEQUENCE
	rcVlanIgmpSnoopSenderVlanId	INTEGER
	rcVlanIgmpSnoopSenderIpAddress	IpAddress
	rcVlanIgmpSnoopSenderIfIndex	InterfaceIndex
	rcVlanIgmpSnoopSenderMember	IpAddress
	rcVlanIgmpSnoopSenderAction	INTEGER

RcVlanLoopDetectedEntry
SEQUENCE
	rcVlanLoopDetectedPortIndex	Integer32
	rcVlanLoopDetectedVlanId	Integer32
	rcVlanLoopDetectedValue	INTEGER

RcVlanDsapSsapEntry
SEQUENCE
	rcVlanDsapSsapVlanId	Integer32
	rcVlanDsapSsapPid	INTEGER
	rcVlanDsapSsapRowStatus	RowStatus

RcVlanNewLoopDetectedEntry
SEQUENCE
	rcVlanNewLoopDetectedPortIndex	InterfaceIndex
	rcVlanNewLoopDetectedVlanId	Integer32
	rcVlanNewLoopDetectedMac	MacAddress
	rcVlanNewLoopDetectedAction	INTEGER
	rcVlanNewLoopDetectedSmltRemote	TruthValue

RcVlanClearMacRecordEntry
SEQUENCE
	rcVlanClearMacRecordAddr	MacAddress
	rcVlanClearMacRecordVlanId	INTEGER
	rcVlanClearMacRecordAllVlanIds	TruthValue
	rcVlanClearMacRecordForceDelete	TruthValue
	rcVlanClearMacRecordLCForceDelete	TruthValue

RcChasFanEntry
SEQUENCE
	rcChasFanId	INTEGER
	rcChasFanOperStatus	INTEGER
	rcChasFanAmbientTemperature	Gauge32
	rcChasFanType	INTEGER

RcChasPowerSupplyEntry
SEQUENCE
	rcChasPowerSupplyId	INTEGER
	rcChasPowerSupplyOperStatus	INTEGER

RcChasPowerSupplyDetailEntry
SEQUENCE
	rcChasPowerSupplyDetailId	INTEGER
	rcChasPowerSupplyDetailType	INTEGER
	rcChasPowerSupplyDetailSerialNumber	DisplayString
	rcChasPowerSupplyDetailHardwareRevision	DisplayString
	rcChasPowerSupplyDetailPartNumber	DisplayString
	rcChasPowerSupplyDetailDescription	DisplayString
	rcChasPowerSupplyDetailInputLineVoltage	INTEGER
	rcChasPowerSupplyDetailOperLineVoltage	INTEGER

RcCardEntry
SEQUENCE
	rcCardIndex	INTEGER
	rcCardType	INTEGER
	rcCardSerialNumber	DisplayString
	rcCardHardwareRevision	DisplayString
	rcCardAdminStatus	INTEGER
	rcCardOperStatus	INTEGER
	rcCardPCMCIAType	INTEGER
	rcCardPartNumber	DisplayString

RcPortEntry
SEQUENCE
	rcPortIndex	InterfaceIndex
	rcPortType	INTEGER
	rcPortConnectorType	INTEGER
	rcPortPerformRouting	TruthValue
	rcPortHighPriority	TruthValue
	rcPortAction	INTEGER
	rcPortResult	INTEGER
	rcPortPrimaryConnector	INTEGER
	rcPortActiveConnector	INTEGER
	rcPortBackupConnectorStatus	INTEGER
	rcPortAutoNegotiate	TruthValue
	rcPortAdminDuplex	INTEGER
	rcPortOperDuplex	INTEGER
	rcPortAdminSpeed	INTEGER
	rcPortOperSpeed	Integer32
	rcPortMltId	Integer32
	rcPortLocked	TruthValue
	rcPortAutoNegotiationSupported	TruthValue
	rcPortSingleRoutablePort	TruthValue
	rcPortUnknownMacDiscard	TruthValue
	rcPortNumStateTransition	Counter32
	rcPortAllowOversizeFrame	TruthValue
	rcPortUserPriority	INTEGER
	rcPortQosLevel	INTEGER
	rcPortDiffServEnable	TruthValue
	rcPortDiffServType	INTEGER
	rcPortDiffServIeee8021POverrideEnable	TruthValue
	rcPortVendorDescr	DisplayString
	rcPortName	DisplayString	Size(0..42)
	rcPortOctapidId	Integer32
	rcPortWan	INTEGER
	rcPortTransport	INTEGER
	rcPortMultimediaFilterEnable	TruthValue
	rcPortMultimediaDevSelection	DisplayString
	rcPortAdminRouting	EnableValue
	rcPortOperRouting	EnableValue
	rcPortPid	Integer32
	rcPortIeee8021POverrideEnable	TruthValue
	rcPortCpLimitShutDown	TruthValue
	rcPortHighSecureEnable	TruthValue
	rcPortMrouteStrLimit	INTEGER
	rcPortMrouteStrTimerCheck	INTEGER
	rcPortMrouteStrLimitEnable	TruthValue
	rcPortAutoNegAd	BITS
	rcPortAutoRecoverPort	TruthValue
	rcPortExtCplimitConf	INTEGER
	rcPortExtCplimitUtilRate	INTEGER
	rcPortEgressRateLimit	INTEGER
	rcPortEgressRateLimitState	EnableValue
	rcPortBpduFilteringTimerCount	TimeInterval
	rcPortBpduFilteringTimeout	TimeInterval
	rcPortBpduFilteringAdminEnabled	TruthValue
	rcPortBpduFilteringOperEnabled	TruthValue
	rcPortCpLimitEnable	EnableValue
	rcPortCpMulticastLimit	INTEGER
	rcPortCpBroadcastLimit	INTEGER
	rcPortIngressRateLimit	INTEGER
	rcPortIngressRateLimitState	EnableValue
	rcPortClockSource	INTEGER
	rcPortVrfIdList	IdList
	rcPortVrfNameList	OCTET STRING
	rcPortBrouterVrfId	VrfIdentifier
	rcPortBrouterVrfName	DisplayString
	rcPortVrfCount	Counter32

RcPortPcapEntry
SEQUENCE
	rcPortPcapIndex	InterfaceIndex
	rcPortPcapEnable	TruthValue
	rcPortPcapMode	INTEGER
	rcPortPcapFilterListSize	INTEGER
	rcPortPcapFilterList	OCTET STRING
	rcPortPcapAclFilterListSize	INTEGER
	rcPortPcapAclFilterList	OCTET STRING

RcPortLacpEntry
SEQUENCE
	rcPortLacpAdminEnable	TruthValue
	rcPortLacpOperEnable	TruthValue
	rcPortLacpFastPeriodicTime	INTEGER
	rcPortLacpSlowPeriodicTime	INTEGER
	rcPortLacpTimeoutScale	INTEGER
	rcPortLacpAggrWaitTime	INTEGER
	rcPortLacpFastPeriodicTimeOper	INTEGER
	rcPortLacpSlowPeriodicTimeOper	INTEGER
	rcPortLacpTimeoutScaleOper	INTEGER
	rcPortLacpAggrWaitTimeOper	INTEGER

RcPortVLacpEntry
SEQUENCE
	rcPortVLacpAdminEnable	TruthValue
	rcPortVLacpOperEnable	TruthValue
	rcPortVLacpFastPeriodicTimer	INTEGER
	rcPortVLacpSlowPeriodicTimer	INTEGER
	rcPortVLacpTimeout	INTEGER
	rcPortVLacpTimeoutScale	INTEGER
	rcPortVLacpEtherType	Integer32
	rcPortVLacpEtherMacAddress	MacAddress
	rcPortVLacpPortState	INTEGER
	rcPortVLacpFlapDetectEnable	TruthValue
	rcPortVLacpFlapFrequency	Integer32	3..30
	rcPortVLacpFlapInterval	Integer32	10..600
	rcPortVLacpTotalFlapCount	Counter32
	rcPortVLacpFirstFlapTimeStamp	DateAndTime
	rcPortVLacpLastFlapTimeStamp	DateAndTime
	rcPortVLacpFlapClearStats	TruthValue

RcPortRemoteMirroringEntry
SEQUENCE
	rcPortRemoteMirroringIndex	InterfaceIndex
	rcPortRemoteMirroringEnable	TruthValue
	rcPortRemoteMirroringMode	INTEGER
	rcPortRemoteMirroringSrcMac	MacAddress
	rcPortRemoteMirroringDstMac	MacAddress
	rcPortRemoteMirroringEtherType	INTEGER
	rcPortRemoteMirroringVlanIdListSize	INTEGER
	rcPortRemoteMirroringVlanIdList	OCTET STRING	Size(4096)
	rcPortRemoteMirroringRowStatus	RowStatus

RcPortMgmtLinkEntry
SEQUENCE
	rcPortMgmtLinkIndex	InterfaceIndex
	rcPortMgmtLinkDescr	DisplayString
	rcPortMgmtLinkOperStatus	INTEGER
	rcPortMgmtLinkAutoNegotiate	TruthValue
	rcPortMgmtLinkDuplex	INTEGER
	rcPortMgmtLinkSpeed	INTEGER

RcPortFlushMacEntry
SEQUENCE
	rcPortFlushMacPortNum	INTEGER
	rcPortFlushMacAddr	OCTET STRING
	rcPortFlushMacVlanId	INTEGER

RcLaunchPadEntry
SEQUENCE
	rcLaunchPadSlotId	Integer32
	rcLaunchPadMiniSlotId	Integer32
	rcLaunchPadAppType	INTEGER
	rcLaunchPadMiniSlotIp	IpAddress
	rcLaunchPadNaapLpState	EnableValue
	rcLaunchPadMiniSlotSwVersion	DisplayString
	rcLaunchPadHWType	INTEGER

RcLaunchPadClusterEntry
SEQUENCE
	rcLaunchPadClusterId	INTEGER
	rcLaunchPadClusterType	INTEGER
	rcLaunchPadClusterSize	INTEGER
	rcLaunchPadClusterMembers	OCTET STRING	Size(0..32)
	rcLaunchPadClusterRowStatus	RowStatus
	rcLaunchPadClusterMgmtVlan	INTEGER
	rcLaunchPadClusterSyncVlan	INTEGER
	rcLaunchPadClusterTpsSize	INTEGER
	rcLaunchPadClusterTpsMembers	OCTET STRING	Size(0..32)
	rcLaunchPadClusterPortMember	PortSet

RcAgentEntry
SEQUENCE
	rcAgentId	Integer32
	rcAgentSlot	Integer32
	rcAgentIpAddr	IpAddress

RcIpConfEntry
SEQUENCE
	rcIpConfIfIndex	InterfaceIndexOrZero
	rcIpConfAdvertDefRte	TruthValue
	rcIpConfAcceptDefRte	TruthValue
	rcIpConfRowStatus	RowStatus
	rcIpConfRipEnable	TruthValue
	rcIpConfOspfEnable	TruthValue
	rcIpConfIgmpEnable	TruthValue
	rcIpConfAddrAssigned	TruthValue
	rcIpConfDhcpEnable	TruthValue
	rcIpConfTriggeredUpdateEnable	TruthValue
	rcIpConfAutoAggrerateEnable	TruthValue
	rcIpConfGenerateDefaultRoute	TruthValue
	rcIpConfAdvertiseWhenDown	TruthValue
	rcIpConfDirectBroadcastEnable	TruthValue
	rcIpConfRipInPolicy	DisplayString
	rcIpConfRipOutPolicy	DisplayString
	rcIpConfOspfIfType	INTEGER
	rcIpConfRipCost	INTEGER
	rcIpConfRipHolddown	INTEGER
	rcIpConfRipTimeout	INTEGER
	rcIpConfRsmltEnable	TruthValue
	rcIpConfReversePathCheckEnable	TruthValue
	rcIpConfReversePathCheckMode	INTEGER
	rcIpConfIsisEnable	TruthValue
	rcIpConfBfdEnable	TruthValue
	rcIpConfIpVpnLiteEnable	TruthValue

RcIpConfOspfEntry
SEQUENCE
	rcIpConfOspfIfIndex	InterfaceIndexOrZero
	rcIpConfOspfRtrPriority	INTEGER
	rcIpConfOspfMetric	INTEGER
	rcIpConfOspfAuthKey	DisplayString	Size(0..8)
	rcIpConfOspfRowStatus	RowStatus
	rcIpConfOspfHelloInterval	INTEGER
	rcIpConfOspfRtrDeadInterval	INTEGER
	rcIpConfOspfIfAreaId	IpAddress
	rcIpConfOspfAuthType	INTEGER
	rcIpConfOspfPollInterval	INTEGER
	rcIpConfOspfIfMtuIgnore	INTEGER
	rcIpConfOspfBfdEnable	EnableValue

RcIpConfOspfAreaEntry
SEQUENCE
	rcIpConfOspfAreaId	IpAddress
	rcIpConfOspfAreaImportSummary	TruthValue
	rcIpConfOspfAreaActiveIfCount	Integer32

RcIpConfV2Entry
SEQUENCE
	rcIpConfV2Index	InterfaceIndexOrZero
	rcIpConfV2Addr	IpAddress
	rcIpConfV2RowStatus	RowStatus
	rcIpConfV2AdvertDefRte	TruthValue
	rcIpConfV2AcceptDefRte	TruthValue
	rcIpConfV2RipEnable	TruthValue
	rcIpConfV2OspfEnable	TruthValue
	rcIpConfV2IgmpEnable	TruthValue
	rcIpConfV2AddrAssigned	TruthValue
	rcIpConfV2TriggeredUpdateEnable	TruthValue
	rcIpConfV2RipAutoAggrerateEnable	TruthValue
	rcIpConfV2RipGenerateDefaultRoute	TruthValue
	rcIpConfV2AdvertiseWhenDown	TruthValue

RcIpConfOspfV2Entry
SEQUENCE
	rcIpConfOspfV2IfIndex	InterfaceIndexOrZero
	rcIpConfOspfV2IpAddr	IpAddress
	rcIpConfOspfV2RtrPriority	INTEGER
	rcIpConfOspfV2Metric	INTEGER
	rcIpConfOspfV2AuthKey	DisplayString
	rcIpConfOspfV2RowStatus	RowStatus
	rcIpConfOspfV2HelloInterval	INTEGER
	rcIpConfOspfV2RtrDeadInterval	INTEGER
	rcIpConfOspfV2IfAreaId	IpAddress
	rcIpConfOspfV2AuthType	INTEGER

RcIpConfOspfAreaAggregateEntry
SEQUENCE
	rcIpConfOspfAreaAggregateAreaID	IpAddress
	rcIpConfOspfAreaAggregateLsdbType	INTEGER
	rcIpConfOspfAreaAggregateNet	IpAddress
	rcIpConfOspfAreaAggregateMask	IpAddress
	rcIpConfOspfAreaAggregateAdvertiseMetric	INTEGER	0..65535
	rcIpConfOspfAreaAggregateEffect	INTEGER

RcIpConfRsmltEntry
SEQUENCE
	rcIpConfRsmltIfIndex	InterfaceIndex
	rcIpConfRsmltHoldDownTimer	INTEGER
	rcIpConfRsmltHoldUpTimer	INTEGER
	rcIpConfRsmltRowStatus	RowStatus

RcIpConfBfdEntry
SEQUENCE
	rcIpConfBfdIfIndex	InterfaceIndex
	rcIpConfBfdMinRxInterval	Integer32
	rcIpConfBfdTxInterval	Integer32
	rcIpConfBfdMultiplier	Integer32
	rcIpConfBfdRowStatus	RowStatus
	rcIpConfBfdHoldOffInterval	Unsigned32
	rcIpConfBfdStaticFlag	EnableValue

RcIpAddrEntry
SEQUENCE
	rcIpAdEntIfIndex	InterfaceIndex
	rcIpAdEntAddr	IpAddress
	rcIpAdEntNetMask	IpAddress
	rcIpAdEntBcastAddrFormat	INTEGER
	rcIpAdEntReasmMaxSize	INTEGER	0..65535
	rcIpAdEntRowStatus	RowStatus
	rcIpAdEntVlanId	INTEGER
	rcIpAdEntBrouterPort	TruthValue
	rcIpAdEntMacOffset	INTEGER
	rcIpAdEntIfType	INTEGER
	rcIpAdEntVrfId	VrfIdentifier

RcIpFlowEntry
SEQUENCE
	rcIpFlowSrcIpAddress	IpAddress
	rcIpFlowSrcIpPort	INTEGER
	rcIpFlowDstIpAddress	IpAddress
	rcIpFlowDstIpPort	INTEGER
	rcIpFlowProtocol	INTEGER
	rcIpFlowRowStatus	RowStatus

RcIpConfIgmpEntry
SEQUENCE
	rcIpConfIgmpIfIndex	INTEGER
	rcIpConfIgmpQueryInterval	INTEGER
	rcIpConfIgmpVersion	INTEGER
	rcIpConfIgmpQueryMaxResponseTime	INTEGER
	rcIpConfIgmpQuerierPresentTimeout	Integer32
	rcIpConfIgmpLeaveEnabled	TruthValue
	rcIpConfIgmpRowStatus	RowStatus
	rcIpConfIgmpRobustness	INTEGER
	rcIpConfIgmpLastMemberQueryInterval	INTEGER
	rcIpConfIgmpSnoopEnable	TruthValue
	rcIpConfIgmpProxySnoopEnable	TruthValue

RcIgmpGroupEntry
SEQUENCE
	rcIgmpGroupIpAddress	IpAddress
	rcIgmpGroupMembers	IpAddress
	rcIgmpGroupInPort	INTEGER
	rcIgmpGroupExpiration	Integer32
	rcIgmpGroupIfIndex	InterfaceIndex
	rcIgmpGroupUserId	DisplayString
	rcIgmpGroupMemberState	INTEGER
	rcIgmpGroupSessionTime	Integer32

RcIpRouteEntry
SEQUENCE
	rcIpRouteDest	IpAddress
	rcIpRouteMask	IpAddress
	rcIpRouteNextHop	IpAddress
	rcIpRouteMetric	Integer32
	rcIpRouteIfIndex	InterfaceIndex
	rcIpRouteType	INTEGER
	rcIpRouteProto	INTEGER
	rcIpRouteAge	Integer32
	rcIpRouteRowStatus	RowStatus
	rcIpRoutePref	INTEGER
	rcIpRouteAltSequence	Integer32
	rcIpRoutePathType	INTEGER
	rcIpRouteSrcVrfId	VrfIdentifier
	rcIpRouteNextHopId	DisplayString

RcIpConfDhcpEntry
SEQUENCE
	rcIpConfDhcpIfIndex	InterfaceIndexOrZero
	rcIpConfDhcpMaxHop	INTEGER
	rcIpConfDhcpMinSec	INTEGER
	rcIpConfDhcpMode	INTEGER
	rcIpConfDhcpRowStatus	RowStatus
	rcIpConfDhcpNumRequests	Counter32
	rcIpConfDhcpNumReplies	Counter32
	rcIpConfDhcpAlwaysBroadcast	TruthValue

RcIpDhcpForwardEntry
SEQUENCE
	rcIpDhcpForwardAgentAddr	IpAddress
	rcIpDhcpForwardServerAddr	IpAddress
	rcIpDhcpForwardEnable	TruthValue
	rcIpDhcpForwardMode	INTEGER
	rcIpDhcpForwardRowStatus	RowStatus

RcIpFilterEntry
SEQUENCE
	rcIpFilterType	INTEGER
	rcIpFilterDstAddr	IpAddress
	rcIpFilterDstMask	IpAddress
	rcIpFilterSrcAddr	IpAddress
	rcIpFilterSrcMask	IpAddress
	rcIpFilterId	INTEGER	1..4096
	rcIpFilterName	DisplayString	Size(0..15)
	rcIpFilterProtocolType	INTEGER
	rcIpFilterSrcPort	INTEGER	0..65535
	rcIpFilterSrcOption	INTEGER
	rcIpFilterDstPort	INTEGER	0..65535
	rcIpFilterDstOption	INTEGER
	rcIpFilterCopyToCpu	TruthValue
	rcIpFilterMirror	TruthValue
	rcIpFilterHighPriority	TruthValue
	rcIpFilterTcpConnect	TruthValue
	rcIpFilterIeeeVlanPriority	INTEGER
	rcIpFilterUsePktLimit	TruthValue
	rcIpFilterPktLimit	INTEGER
	rcIpFilterRowStatus	RowStatus
	rcIpFilterMode	INTEGER
	rcIpFilterIpTosRule	INTEGER
	rcIpFilterStopOnMatch	TruthValue
	rcIpFilterDiffServMatchIeee8021PEnable	TruthValue
	rcIpFilterDiffServMatchIeee8021P	INTEGER	0..7
	rcIpFilterDiffServMatchDscpEnable	TruthValue
	rcIpFilterDiffServMatchDscp	DisplayString	Size(6)
	rcIpFilterDiffServMatchDscpReserved	DisplayString	Size(2)
	rcIpFilterDiffServModifyIeee8021PEnable	TruthValue
	rcIpFilterDiffServModifyIeee8021P	INTEGER	0..7
	rcIpFilterDiffServModifyDscpEnable	TruthValue
	rcIpFilterDiffServModifyDscp	DisplayString	Size(6)
	rcIpFilterDiffServModifyDscpReserved	DisplayString	Size(2)
	rcIpFilterDiffServTrafficProfileId	INTEGER	0..64
	rcIpFilterMatchIcmpRequest	TruthValue
	rcIpFilterMatchIpFragment	TruthValue
	rcIpFilterStatisticEnable	TruthValue
	rcIpFilterInOctets	Counter64
	rcIpFilterInPackets	Counter64
	rcIpFilterRateLimitDiscardPackets	Counter64
	rcIpFilterNextHopForwardIpAddr	IpAddress
	rcIpFilterNextHopUnreachableDropEnable	TruthValue
	rcIpFilterProtocolTypeUsrDefined	INTEGER
	rcIpFilterIngressOctets	Counter64
	rcIpFilterIngressPkts	Counter64
	rcIpFilterRateLimitDiscardPkts	Counter64

RcIpFilterGlobalListEntry
SEQUENCE
	rcIpFilterGlobalListId	INTEGER	1..100
	rcIpFilterGlobalListName	DisplayString	Size(0..15)
	rcIpFilterGlobalListFilterIdListSize	INTEGER	0..8
	rcIpFilterGlobalListFilterIdList	IdList	Size(16)
	rcIpFilterGlobalListRowStatus	RowStatus
	rcIpFilterGlobalListMemberPorts	PortSet

RcIpFilterBaseListEntry
SEQUENCE
	rcIpFilterBaseListId	INTEGER	300..1000
	rcIpFilterBaseListName	DisplayString	Size(0..15)
	rcIpFilterBaseListFilterIdListSize	INTEGER	0..128
	rcIpFilterBaseListFilterIdList	IdList	Size(256)
	rcIpFilterBaseListRowStatus	RowStatus
	rcIpFilterBaseListMemberPorts	PortSet

RcIpFilterPortEntry
SEQUENCE
	rcIpFilterPortIfIndex	InterfaceIndex
	rcIpFilterPortFilterListSize	INTEGER	0..128
	rcIpFilterPortFilterList	OCTET STRING	Size(256)
	rcIpFilterPortMode	INTEGER
	rcIpFilterPortEnable	TruthValue
	rcIpFilterPortRowStatus	RowStatus
	rcIpFilterPortDefaultAction	INTEGER
	rcIpFilterPortNumGlobalFilters	Integer32
	rcIpFilterPortNumBaseFilters	Integer32

RcIpFilterMediaDevEntry
SEQUENCE
	rcIpFilterMediaDevId	INTEGER
	rcIpFilterMediaDevName	DisplayString
	rcIpFilterMediaDevPlatformType	INTEGER
	rcIpFilterMediaDevDeviceType	INTEGER
	rcIpFilterMediaDevIpAddress	IpAddress
	rcIpFilterMediaDevStreamsIds	IdList
	rcIpFilterMediaDevMemberPorts	PortSet
	rcIpFilterMediaDevStatisticEnable	TruthValue
	rcIpFilterMediaDevRowStatus	RowStatus

RcIpFilterMediaStreamEntry
SEQUENCE
	rcIpFilterMediaStreamMediaId	INTEGER
	rcIpFilterMediaStreamStreamId	INTEGER
	rcIpFilterMediaStreamName	DisplayString
	rcIpFilterMediaStreamProtocol	INTEGER
	rcIpFilterMediaStreamPortMin	INTEGER
	rcIpFilterMediaStreamPortMax	INTEGER
	rcIpFilterMediaStreamPortOption	INTEGER
	rcIpFilterMediaStreamType	INTEGER
	rcIpFilterMediaStreamRemarkDscp	DisplayString
	rcIpFilterMediaStreamMatchDscp	DisplayString
	rcIpFilterMediaStreamRowStatus	RowStatus

RcIpPolicyAddrEntry
SEQUENCE
	rcIpPolicyAddrIpAddr	IpAddress
	rcIpPolicyAddrId	Integer32
	rcIpPolicyAddrAddrListIdListSize	INTEGER	0..128
	rcIpPolicyAddrAddrListIdList	OCTET STRING	Size(256)
	rcIpPolicyAddrRowStatus	RowStatus

RcIpPolicyNetEntry
SEQUENCE
	rcIpPolicyNetAddr	IpAddress
	rcIpPolicyNetMask	IpAddress
	rcIpPolicyNetId	Integer32
	rcIpPolicyNetNetListIdListSize	INTEGER	0..128
	rcIpPolicyNetNetListIdList	OCTET STRING	Size(256)
	rcIpPolicyNetRowStatus	RowStatus

RcIpPolicyAddrListEntry
SEQUENCE
	rcIpPolicyAddrListId	INTEGER	1..1000
	rcIpPolicyAddrListName	DisplayString	Size(0..15)
	rcIpPolicyAddrListIdListSize	INTEGER	0..128
	rcIpPolicyAddrListIdList	OCTET STRING	Size(256)
	rcIpPolicyAddrListPolicyIdListSize	INTEGER	0..128
	rcIpPolicyAddrListPolicyIdList	OCTET STRING	Size(256)
	rcIpPolicyAddrListRowStatus	RowStatus

RcIpPolicyRipAnnounceEntry
SEQUENCE
	rcIpPolicyRipAnnounceId	INTEGER	1..1000
	rcIpPolicyRipAnnounceName	DisplayString	Size(0..15)
	rcIpPolicyRipAnnounceEnable	TruthValue
	rcIpPolicyRipAnnounceExactNetListId	INTEGER	0..1000
	rcIpPolicyRipAnnounceRangeNetListId	INTEGER	0..1000
	rcIpPolicyRipAnnounceRipGatewayListId	INTEGER	0..1000
	rcIpPolicyRipAnnounceRipInterfaceListId	INTEGER	0..1000
	rcIpPolicyRipAnnounceOspfRouterListId	INTEGER	0..1000
	rcIpPolicyRipAnnounceAnnounceInterfaceListId	INTEGER	0..1000
	rcIpPolicyRipAnnouncePrecedence	INTEGER
	rcIpPolicyRipAnnounceRouteSource	INTEGER
	rcIpPolicyRipAnnounceAdvertiseNetListId	INTEGER	0..1000
	rcIpPolicyRipAnnounceAction	INTEGER
	rcIpPolicyRipAnnounceOspfRouteType	INTEGER
	rcIpPolicyRipAnnounceRipMetric	INTEGER	0..15
	rcIpPolicyRipAnnounceRowStatus	RowStatus

RcIpPolicyOspfAnnounceEntry
SEQUENCE
	rcIpPolicyOspfAnnounceId	INTEGER	2001..3000
	rcIpPolicyOspfAnnounceName	DisplayString	Size(0..15)
	rcIpPolicyOspfAnnounceEnable	TruthValue
	rcIpPolicyOspfAnnounceExactNetListId	INTEGER	0..1000
	rcIpPolicyOspfAnnounceRangeNetListId	INTEGER	0..1000
	rcIpPolicyOspfAnnounceRipGatewayListId	INTEGER	0..1000
	rcIpPolicyOspfAnnounceRipInterfaceListId	INTEGER	0..1000
	rcIpPolicyOspfAnnouncePrecedence	INTEGER
	rcIpPolicyOspfAnnounceRouteSource	INTEGER
	rcIpPolicyOspfAnnounceAdvertiseNetListId	INTEGER	0..1000
	rcIpPolicyOspfAnnounceAction	INTEGER
	rcIpPolicyOspfAnnounceExtMetricType	INTEGER
	rcIpPolicyOspfAnnounceExtMetric	INTEGER	0..65535
	rcIpPolicyOspfAnnounceRowStatus	RowStatus

RcIpPolicyRipAcceptEntry
SEQUENCE
	rcIpPolicyRipAcceptId	INTEGER	4001..5000
	rcIpPolicyRipAcceptName	DisplayString	Size(0..15)
	rcIpPolicyRipAcceptEnable	TruthValue
	rcIpPolicyRipAcceptExactNetListId	INTEGER	0..1000
	rcIpPolicyRipAcceptRangeNetListId	INTEGER	0..1000
	rcIpPolicyRipAcceptRipGatewayListId	INTEGER	0..1000
	rcIpPolicyRipAcceptRipInterfaceListId	INTEGER	0..1000
	rcIpPolicyRipAcceptPrecedence	INTEGER
	rcIpPolicyRipAcceptAction	INTEGER
	rcIpPolicyRipAcceptInjectNetListId	INTEGER	0..1000
	rcIpPolicyRipAcceptApplyMask	IpAddress
	rcIpPolicyRipAcceptRowStatus	RowStatus

RcIpPolicyOspfAcceptEntry
SEQUENCE
	rcIpPolicyOspfAcceptId	INTEGER	6001..7000
	rcIpPolicyOspfAcceptName	DisplayString	Size(0..15)
	rcIpPolicyOspfAcceptEnable	TruthValue
	rcIpPolicyOspfAcceptExactNetListId	INTEGER	0..1000
	rcIpPolicyOspfAcceptRangeNetListId	INTEGER	0..1000
	rcIpPolicyOspfAcceptPrecedence	INTEGER
	rcIpPolicyOspfAcceptAction	INTEGER
	rcIpPolicyOspfAcceptInjectNetListId	INTEGER	0..1000
	rcIpPolicyOspfAcceptExtType	INTEGER
	rcIpPolicyOspfAcceptRowStatus	RowStatus

RcIpPolicyNetListEntry
SEQUENCE
	rcIpPolicyNetListId	INTEGER	1..1000
	rcIpPolicyNetListName	DisplayString	Size(0..15)
	rcIpPolicyNetListIdListSize	INTEGER	0..128
	rcIpPolicyNetListIdList	OCTET STRING	Size(256)
	rcIpPolicyNetListPolicyIdListSize	INTEGER	0..128
	rcIpPolicyNetListPolicyIdList	OCTET STRING	Size(256)
	rcIpPolicyNetListRowStatus	RowStatus

RcIpDvmrpTableEntry
SEQUENCE
	rcIpDvmrpTableIfIndex	InterfaceIndex
	rcIpDvmrpTableEnable	TruthValue
	rcIpDvmrpTableMetric	INTEGER
	rcIpDvmrpTableAdvSelf	TruthValue
	rcIpDvmrpTableLocalAddr	IpAddress
	rcIpDvmrpTableInPolicyName	DisplayString
	rcIpDvmrpTableOutPolicyName	DisplayString
	rcIpDvmrpTableDefRtLis	TruthValue
	rcIpDvmrpTableDefRtSup	TruthValue
	rcIpDvmrpTableDefRtMet	Integer32
	rcIpDvmrpTableInterfaceType	INTEGER

RcIpUdpProtocolEntry
SEQUENCE
	rcIpUdpProtocolPortNumber	INTEGER
	rcIpUdpProtocolName	DisplayString
	rcIpUdpProtocolRowStatus	RowStatus

RcIpUdpPortFwdEntry
SEQUENCE
	rcIpUdpPortFwdDestPort	INTEGER
	rcIpUdpPortFwdDestAddr	IpAddress
	rcIpUdpPortFwdId	Integer32
	rcIpUdpPortFwdFwdListIdListSize	INTEGER	0..128
	rcIpUdpPortFwdFwdListIdList	IdList	Size(64)
	rcIpUdpPortFwdNumFwdPackets	Counter32
	rcIpUdpPortFwdNumDropPacketsTtlExpired	Counter32
	rcIpUdpPortFwdNumDropPacketsDestUnreach	Counter32
	rcIpUdpPortFwdRowStatus	RowStatus

RcIpUdpPortFwdListEntry
SEQUENCE
	rcIpUdpPortFwdListId	INTEGER	1..1000
	rcIpUdpPortFwdListName	DisplayString	Size(0..15)
	rcIpUdpPortFwdListFwdIdListSize	INTEGER	0..64
	rcIpUdpPortFwdListFwdIdList	OCTET STRING	Size(128)
	rcIpUdpPortFwdListRowStatus	RowStatus

RcIpUdpConfBroadcastIntfEntry
SEQUENCE
	rcIpUdpConfBroadcastIntfLocalIfAddr	IpAddress
	rcIpUdpConfBroadcastIntfUdpPortFwdListId	INTEGER	0..1000
	rcIpUdpConfBroadcastIntfMaxTtl	INTEGER	1..16
	rcIpUdpConfBroadcastIntfNumRxPkts	Counter32
	rcIpUdpConfBroadcastIntfNumFwdPkts	Counter32
	rcIpUdpConfBroadcastIntfNumDropPktsMaxTtlExpired	Counter32
	rcIpUdpConfBroadcastIntfNumDropPktsDestUnreach	Counter32
	rcIpUdpConfBroadcastIntfNumDropPktsUnknownPort	Counter32
	rcIpUdpConfBroadcastIntfRowStatus	RowStatus
	rcIpUdpConfBroadcastIntfBroadCastMask	IpAddress

RcIpStaticRouteEntry
SEQUENCE
	rcIpStaticRouteDest	IpAddress
	rcIpStaticRouteMask	IpAddress
	rcIpStaticRouteNextHop	IpAddress
	rcIpStaticRouteMetric	INTEGER	1..FFFF
	rcIpStaticRouteIfIndex	InterfaceIndex	0..65535
	rcIpStaticRoutePreference	INTEGER	1..255
	rcIpStaticRouteEnable	TruthValue
	rcIpStaticRouteStatus	INTEGER
	rcIpStaticRouteRowStatus	RowStatus
	rcIpStaticRouteLocalNextHop	TruthValue

RcIpStaticRouteBfdEntry
SEQUENCE
	rcIpStaticRouteBfdNextHop	IpAddress
	rcIpStaticRouteBfdRowStatus	RowStatus

RcIpPimEntry
SEQUENCE
	rcIpPimIfIndex	InterfaceIndex
	rcIpPimEnable	TruthValue
	rcIpPimMode	INTEGER
	rcIpPimHelloInterval	INTEGER
	rcIpPimJoinPruneInterval	INTEGER
	rcIpPimCBSRPreference	INTEGER
	rcIpPimIntfType	INTEGER

RcIpPimInterfaceEntry
SEQUENCE
	rcIpPimInterfaceIfIndex	InterfaceIndex
	rcIpPimInterfaceOperState	INTEGER
	rcIpPimInterfaceType	INTEGER
	rcIpPimInterfaceCBSREnable	TruthValue

RcIpPimStaticRPEntry
SEQUENCE
	rcIpPimStaticRPGroupAddress	IpAddress
	rcIpPimStaticRPGroupMask	IpAddress
	rcIpPimStaticRPAddress	IpAddress
	rcIpPimStaticRPRowStatus	RowStatus
	rcIpPimStaticRPStatus	INTEGER

RcIpPimVirtualNbrEntry
SEQUENCE
	rcIpPimVirtualNbrAddress	IpAddress
	rcIpPimVirtualNbrIfIndex	InterfaceIndex
	rcIpPimVirtualNbrRowStatus	RowStatus

RcIpMulticastArpEntry
SEQUENCE
	rcIpMulticastArpVlanId	Integer32
	rcIpMulticastArpMacAddress	MacAddress
	rcIpMulticastArpIpAddress	IpAddress
	rcIpMulticastArpPorts	PortSet
	rcIpMulticastArpNumMltIds	Integer32
	rcIpMulticastArpMltIds	IdList
	rcIpMulticastArpRowStatus	RowStatus

RcIpMulticastEntry
SEQUENCE
	rcIpMulticastIfIndex	InterfaceIndex
	rcIpMulticastMulticastIp	IpAddress

RcIpRipInterfaceEntry
SEQUENCE
	rcIpRipInterfaceAddress	IpAddress
	rcIpRipInterfaceIfIndex	InterfaceIndex
	rcIpRipInterfaceRipEnable	EnableValue
	rcIpRipInterfaceAccDefRte	TruthValue
	rcIpRipInterfaceAdvDefRte	TruthValue
	rcIpRipInterfaceAutoAggregate	TruthValue
	rcIpRipInterfaceCost	Integer32
	rcIpRipInterfaceListen	TruthValue
	rcIpRipInterfacePoison	TruthValue
	rcIpRipInterfaceSupply	TruthValue
	rcIpRipInterfaceTriggeredUpdate	TruthValue
	rcIpRipInterfaceInPolicy	DisplayString
	rcIpRipInterfaceOutPolicy	DisplayString
	rcIpRipInterfaceProxyAnnounceFlag	TruthValue
	rcIpRipInterfaceHolddown	INTEGER
	rcIpRipInterfaceTimeout	INTEGER

RcIpMulticastTimedPruneEntry
SEQUENCE
	rcIpMulticastTimedPruneGroupAddress	IpAddress
	rcIpMulticastTimedPruneSourceAddress	IpAddress
	rcIpMulticastTimedPruneSrcSubnetMask	IpAddress
	rcIpMulticastTimedPruneAgingTimer	Integer32
	rcIpMulticastTimedPruneTimeLeft	Integer32
	rcIpMulticastTimedPruneLastActivity	TimeTicks
	rcIpMulticastTimedPruneRowStatus	RowStatus

RcIpConfIcmpRdiscEntry
SEQUENCE
	rcIpConfIcmpRdiscIfIndex	INTEGER
	rcIpConfIcmpRdiscAdvAddress	IpAddress
	rcIpConfIcmpRdiscAdvFlag	TruthValue
	rcIpConfIcmpRdiscAdvLifetime	INTEGER
	rcIpConfIcmpRdiscMaxAdvInterval	INTEGER
	rcIpConfIcmpRdiscMinAdvInterval	INTEGER
	rcIpConfIcmpRdiscPreferenceLevel	INTEGER

RcIpMrouteHwEntry
SEQUENCE
	rcIpMrouteHwGroupAddress	IpAddress
	rcIpMrouteHwSubnet	IpAddress
	rcIpMrouteHwInvlan	INTEGER
	rcIpMrouteHwPruned	TruthValue
	rcIpMrouteHwIndex	Integer32

RcIpMrouteHwPrunesEntry
SEQUENCE
	rcIpMrouteHwPrunesGroupAddress	IpAddress
	rcIpMrouteHwPrunesSubnet	IpAddress
	rcIpMrouteHwPrunesInvlan	INTEGER
	rcIpMrouteHwPrunesNeighbor	IpAddress
	rcIpMrouteHwPrunesTimer	Integer32

RcIpMrouteHwSourcesEntry
SEQUENCE
	rcIpMrouteHwSourcesGroupAddress	IpAddress
	rcIpMrouteHwSourcesSubnet	IpAddress
	rcIpMrouteHwSourcesInvlan	INTEGER
	rcIpMrouteHwSourcesAddress	IpAddress
	rcIpMrouteHwSourcesIngressPort	PortSet

RcIpMrouteHwEgressVlansEntry
SEQUENCE
	rcIpMrouteHwEgressVlansGroupAddress	IpAddress
	rcIpMrouteHwEgressVlansSubnet	IpAddress
	rcIpMrouteHwEgressVlansInvlan	INTEGER
	rcIpMrouteHwEgressVlansId	INTEGER
	rcIpMrouteHwEgressVlansPorts	PortSet
	rcIpMrouteHwEgressVlansIndex	Integer32

RcIpRsmltOperEntry
SEQUENCE
	rcIpRsmltOperIfIndex	InterfaceIndex
	rcIpRsmltOperAdminStatus	TruthValue
	rcIpRsmltOperHoldDownTimer	INTEGER
	rcIpRsmltOperHoldDownTimeRemaining	INTEGER
	rcIpRsmltOperHoldUpTimer	INTEGER
	rcIpRsmltOperHoldUpTimeRemaining	INTEGER
	rcIpRsmltOperIpAddr	IpAddress
	rcIpRsmltOperOperStatus	INTEGER
	rcIpRsmltOperSmltId	IdList
	rcIpRsmltOperSltId	IdList
	rcIpRsmltOperVlanId	INTEGER
	rcIpRsmltOperMacAddr	MacAddress
	rcIpRsmltOperRowStatus	RowStatus
	rcIpRsmltOperVrfId	VrfIdentifier
	rcIpRsmltOperVrfName	SnmpAdminString

RcIpRsmltPeerEntry
SEQUENCE
	rcIpRsmltPeerIfIndex	InterfaceIndex
	rcIpRsmltPeerAdminStatus	TruthValue
	rcIpRsmltPeerHoldDownTimer	INTEGER
	rcIpRsmltPeerHoldDownTimeRemaining	INTEGER
	rcIpRsmltPeerHoldUpTimer	INTEGER
	rcIpRsmltPeerHoldUpTimeRemaining	INTEGER
	rcIpRsmltPeerIpAddr	IpAddress
	rcIpRsmltPeerOperStatus	INTEGER
	rcIpRsmltPeerSmltId	IdList
	rcIpRsmltPeerSltId	IdList
	rcIpRsmltPeerVlanId	INTEGER
	rcIpRsmltPeerMacAddr	MacAddress
	rcIpRsmltPeerVrfId	VrfIdentifier
	rcIpRsmltPeerVrfName	SnmpAdminString

RcIpRsmltEdgePeerEntry
SEQUENCE
	rcIpRsmltEdgeVlanId	INTEGER
	rcIpRsmltEdgePeerIpAddress	IpAddress
	rcIpRsmltEdgePeerMacAddress	MacAddress
	rcIpRsmltEdgePeerVrfId	VrfIdentifier
	rcIpRsmltEdgePeerVrfName	SnmpAdminString

RcIpv6RsmltOperEntry
SEQUENCE
	rcIpv6RsmltOperIfIndex	InterfaceIndex
	rcIpv6RsmltOperIpv6Addr	Ipv6Address
	rcIpv6RsmltOperIpv6PrefixLength	Integer32
	rcIpv6RsmltOperAdminStatus	TruthValue
	rcIpv6RsmltOperHoldDownTimer	Integer32
	rcIpv6RsmltOperHoldDownTimeRemaining	Integer32
	rcIpv6RsmltOperHoldUpTimer	Integer32
	rcIpv6RsmltOperHoldUpTimeRemaining	Integer32
	rcIpv6RsmltOperOperStatus	INTEGER
	rcIpv6RsmltOperSmltId	IdList
	rcIpv6RsmltOperSltId	IdList
	rcIpv6RsmltOperVlanId	Integer32
	rcIpv6RsmltOperMacAddr	MacAddress
	rcIpv6RsmltOperVrfId	VrfIdentifier
	rcIpv6RsmltOperVrfName	SnmpAdminString

RcIpv6RsmltPeerEntry
SEQUENCE
	rcIpv6RsmltPeerIfIndex	InterfaceIndex
	rcIpv6RsmltPeerIpv6Addr	Ipv6Address
	rcIpv6RsmltPeerIpv6PrefixLength	Integer32
	rcIpv6RsmltPeerAdminStatus	TruthValue
	rcIpv6RsmltPeerHoldDownTimer	Integer32
	rcIpv6RsmltPeerHoldDownTimeRemaining	Integer32
	rcIpv6RsmltPeerHoldUpTimer	Integer32
	rcIpv6RsmltPeerHoldUpTimeRemaining	Integer32
	rcIpv6RsmltPeerOperStatus	INTEGER
	rcIpv6RsmltPeerSmltId	IdList
	rcIpv6RsmltPeerSltId	IdList
	rcIpv6RsmltPeerVlanId	Integer32
	rcIpv6RsmltPeerMacAddr	MacAddress
	rcIpv6RsmltPeerVrfId	VrfIdentifier
	rcIpv6RsmltPeerVrfName	SnmpAdminString

RcIpv6RsmltEdgePeerEntry
SEQUENCE
	rcIpv6RsmltEdgePeerVlanId	Integer32
	rcIpv6RsmltEdgePeerIpv6Address	Ipv6Address
	rcIpv6RsmltEdgePeerIpv6PrefixLength	Integer32
	rcIpv6RsmltEdgePeerMacAddress	MacAddress
	rcIpv6RsmltEdgePeerVrfId	VrfIdentifier
	rcIpv6RsmltEdgePeerVrfName	SnmpAdminString
	rcIpv6RsmltEdgePeerIsRaPrefix	TruthValue
	rcIpv6RsmltEdgePeerConfType	Integer32
	rcIpv6RsmltEdgePeerNoAdvertise	TruthValue
	rcIpv6RsmltEdgePeerOspf6Advertise	TruthValue
	rcIpv6RsmltEdgePeerPrefCandidate	TruthValue
	rcIpv6RsmltEdgePeerPfxValidLife	Integer32
	rcIpv6RsmltEdgePeerPfxPrefLife	Integer32
	rcIpv6RsmltEdgePeerPfxOnLinkFlag	TruthValue
	rcIpv6RsmltEdgePeerPfxAutoFlag	TruthValue

RcIpAsPathAccessListEntry
SEQUENCE
	rcIpAsPathAccessListId	INTEGER
	rcIpAsPathAccessListMemberId	INTEGER
	rcIpAsPathAccessListMode	INTEGER
	rcIpAsPathAccessListAsRegularExpression	OCTET STRING	Size(0..256)
	rcIpAsPathAccessListRowStatus	RowStatus

RcIpCommunityAccessListEntry
SEQUENCE
	rcIpCommunityAccessListId	INTEGER
	rcIpCommunityAccessListMemberId	INTEGER
	rcIpCommunityAccessListMode	INTEGER
	rcIpCommunityAccessListCommunity	OCTET STRING	Size(0..256)
	rcIpCommunityAccessListRowStatus	RowStatus

RcIpAccessListEntry
SEQUENCE
	rcIpAccessListId	INTEGER
	rcIpAccessListMode	INTEGER
	rcIpAccessListNetwork	IpAddress
	rcIpAccessListNetworkMask	IpAddress
	rcIpAccessListName	DisplayString
	rcIpAccessListRowStatus	RowStatus

RcIpExtendedAccessListEntry
SEQUENCE
	rcIpExtendedAccessListId	INTEGER
	rcIpExtendedAccessListMode	INTEGER
	rcIpExtendedAccessListNetwork	IpAddress
	rcIpExtendedAccessListNetworkWildCard	IpAddress
	rcIpExtendedAccessListNetworkMask	IpAddress
	rcIpExtendedAccessListNetworkMaskWildCard	IpAddress
	rcIpExtendedAccessListName	DisplayString
	rcIpExtendedAccessListRowStatus	RowStatus

RcIpPrefixListEntry
SEQUENCE
	rcIpPrefixListId	Integer32
	rcIpPrefixListPrefix	IpAddress
	rcIpPrefixListPrefixMaskLen	INTEGER
	rcIpPrefixListMaskLenFrom	INTEGER
	rcIpPrefixListMaskLenUpto	INTEGER
	rcIpPrefixListName	DisplayString
	rcIpPrefixListRowStatus	RowStatus

RcIpRoutePolicyEntry
SEQUENCE
	rcIpRoutePolicyId	Integer32
	rcIpRoutePolicySequenceNumber	Integer32
	rcIpRoutePolicyName	DisplayString
	rcIpRoutePolicyEnable	TruthValue
	rcIpRoutePolicyMode	INTEGER
	rcIpRoutePolicyMatchProtocol	INTEGER
	rcIpRoutePolicyMatchAsPath	DisplayString
	rcIpRoutePolicyMatchCommunity	DisplayString
	rcIpRoutePolicyMatchCommunityExact	EnableValue
	rcIpRoutePolicyMatchNetwork	RcLongDisplayString
	rcIpRoutePolicyMatchIpRouteSource	RcLongDisplayString
	rcIpRoutePolicyMatchNextHop	RcLongDisplayString
	rcIpRoutePolicyMatchInterface	RcLongDisplayString
	rcIpRoutePolicyMatchRouteType	INTEGER
	rcIpRoutePolicyMatchMetric	INTEGER
	rcIpRoutePolicyMatchTag	DisplayString
	rcIpRoutePolicySetRoutePreference	INTEGER
	rcIpRoutePolicySetAsPath	DisplayString
	rcIpRoutePolicySetAsPathMode	INTEGER
	rcIpRoutePolicySetAutomaticTag	EnableValue
	rcIpRoutePolicySetCommunityNumber	DisplayString
	rcIpRoutePolicySetCommunityMode	INTEGER
	rcIpRoutePolicySetMetricTypeInternal	Integer32
	rcIpRoutePolicySetMetric	INTEGER
	rcIpRoutePolicySetMetricType	INTEGER
	rcIpRoutePolicySetNextHop	IpAddress
	rcIpRoutePolicySetOrigin	INTEGER
	rcIpRoutePolicySetLocalPref	Integer32
	rcIpRoutePolicySetOriginEgpAs	Integer32
	rcIpRoutePolicySetTag	Integer32
	rcIpRoutePolicySetWeight	Integer32
	rcIpRoutePolicySetInjectNetList	DisplayString
	rcIpRoutePolicyRowStatus	RowStatus
	rcIpRoutePolicySetMask	IpAddress
	rcIpRoutePolicyNssaPbit	EnableValue
	rcIpRoutePolicyMatchVrf	IdList
	rcIpRoutePolicyMatchExtCommunity	DisplayString
	rcIpRoutePolicySetExtCommunity	DisplayString
	rcIpRoutePolicySetExtCommunityMode	INTEGER
	rcIpRoutePolicyMatchLocalPref	Integer32
	rcIpRoutePolicyMatchIpRouteDest	RcLongDisplayString
	rcIpRoutePolicyMatchExtendedPref	OCTET STRING
	rcIpRoutePolicyIpv6SetNextHop	Ipv6Address

RcIpRedistributeEntry
SEQUENCE
	rcIpRedistributeProtocol	INTEGER
	rcIpRedistributeRouteSource	INTEGER
	rcIpRedistributeEnable	EnableValue
	rcIpRedistributeMetric	INTEGER
	rcIpRedistributeMetricType	INTEGER
	rcIpRedistributeMatchRouteType	INTEGER
	rcIpRedistributeSetTag	Integer32
	rcIpRedistributeSubnets	INTEGER
	rcIpRedistributeRoutePolicy	DisplayString
	rcIpRedistributeASNumber	Integer32
	rcIpRedistributeWeight	Integer32
	rcIpRedistributeDefaultOriginate	Integer32
	rcIpRedistributeRowStatus	RowStatus
	rcIpRedistributeLevel	INTEGER

RcIpOspfInFilterEntry
SEQUENCE
	rcIpOspfInFilterAdvertisingRtr	IpAddress
	rcIpOspfInFilterEnable	EnableValue
	rcIpOspfInFilterMetricType	INTEGER
	rcIpOspfInFilterPolicyName	DisplayString
	rcIpOspfInFilterRowStatus	RowStatus

RcIpRoutePrefEntry
SEQUENCE
	rcIpRoutePrefProtocol	INTEGER
	rcIpRoutePrefDefault	INTEGER
	rcIpRoutePrefConfigured	INTEGER

RcIpRedistributeInterVrfEntry
SEQUENCE
	rcIpRedistributeInterVrfDstVrfId	VrfIdentifier
	rcIpRedistributeInterVrfProtocol	INTEGER
	rcIpRedistributeInterVrfSrcVrfId	VrfIdentifier
	rcIpRedistributeInterVrfRouteSource	INTEGER
	rcIpRedistributeInterVrfEnable	EnableValue
	rcIpRedistributeInterVrfMetric	INTEGER
	rcIpRedistributeInterVrfMetricType	INTEGER
	rcIpRedistributeInterVrfMatchRouteType	INTEGER
	rcIpRedistributeInterVrfSetTag	Integer32
	rcIpRedistributeInterVrfSubnets	INTEGER
	rcIpRedistributeInterVrfRoutePolicy	DisplayString
	rcIpRedistributeInterVrfASNumber	Integer32
	rcIpRedistributeInterVrfWeight	Integer32
	rcIpRedistributeInterVrfDefaultOriginate	Integer32
	rcIpRedistributeInterVrfRowStatus	RowStatus

RcIpExtCommunityAccessListEntry
SEQUENCE
	rcIpExtCommunityAccessListId	INTEGER
	rcIpExtCommunityAccessListMemberId	INTEGER
	rcIpExtCommunityAccessListRTType	INTEGER
	rcIpExtCommunityAccessListRTAddress	IpAddress
	rcIpExtCommunityAccessListRTAsNumber	INTEGER
	rcIpExtCommunityAccessListRTAssignedNum	Unsigned32
	rcIpExtCommunityAccessListSooType	INTEGER
	rcIpExtCommunityAccessListSooAddress	IpAddress
	rcIpExtCommunityAccessListSooAsNumber	INTEGER
	rcIpExtCommunityAccessListSooAssignedNum	Unsigned32
	rcIpExtCommunityAccessListVrfId	VrfIdentifier
	rcIpExtCommunityAccessListRowStatus	RowStatus

RcIpExtACLEntry
SEQUENCE
	rcIpExtACLPrefixSourceAddr	IpAddress
	rcIpExtACLPrefixSourceMask	IpAddress
	rcIpExtACLPrefixDestinationAddr	IpAddress
	rcIpExtACLPrefixDestinationMask	IpAddress
	rcIpExtACLPrefixName	SnmpAdminString
	rcIpExtACLPrefixRowStatus	RowStatus

RcIpBgpAggregateEntry
SEQUENCE
	rcIpBgpAggregateAddress	IpAddress
	rcIpBgpAggregateMask	IpAddress
	rcIpBgpAggregateAsSetGenerate	EnableValue
	rcIpBgpAggregateSummaryOnly	EnableValue
	rcIpBgpAggregateSuppressPolicy	DisplayString
	rcIpBgpAggregateAdvertisePolicy	DisplayString
	rcIpBgpAggregateAttributePolicy	DisplayString
	rcIpBgpAggregateRowStatus	RowStatus

RcIpBgpNetworkEntry
SEQUENCE
	rcIpBgpNetworkAddr	IpAddress
	rcIpBgpNetworkMask	IpAddress
	rcIpBgpNetworkRowStatus	RowStatus
	rcIpBgpNetworkMetric	INTEGER

RcIpBgpPeerEntry
SEQUENCE
	rcIpBgpPeerEnable	INTEGER
	rcIpBgpPeerIpAddress	IpAddress
	rcIpBgpPeerRemoteAs	INTEGER
	rcIpBgpPeerGroupName	DisplayString
	rcIpBgpPeerDefaultOriginate	EnableValue
	rcIpBgpPeerEbgpMultiHop	EnableValue
	rcIpBgpPeerAdvertisementInterval	INTEGER
	rcIpBgpPeerPassword	DisplayString
	rcIpBgpPeerWeight	INTEGER
	rcIpBgpPeerMaxPrefix	INTEGER
	rcIpBgpPeerNextHopSelf	TruthValue
	rcIpBgpPeerRoutePolicyIn	DisplayString
	rcIpBgpPeerRoutePolicyOut	DisplayString
	rcIpBgpPeerRouteReflectorClient	TruthValue
	rcIpBgpPeerSoftReconfigurationIn	EnableValue
	rcIpBgpPeerSoftReconfiguration	INTEGER
	rcIpBgpPeerRemovePrivateAs	EnableValue
	rcIpBgpPeerRowStatus	RowStatus
	rcIpBgpPeerMD5Authentication	EnableValue
	rcIpBgpPeerDebugMask	INTEGER
	rcIpBgpPeerSendCommunity	EnableValue
	rcIpBgpPeerUpdateSourceInterface	IpAddress
	rcIpBgpPeerState	INTEGER
	rcIpBgpPeerLastError	OCTET STRING
	rcIpBgpPeerVpnv4Address	EnableValue
	rcIpBgpPeerIpvpnLiteCap	EnableValue
	rcIpBgpPeerSooAddress	IpAddress
	rcIpBgpPeerSooAsNumber	INTEGER
	rcIpBgpPeerSooAssignedNum	Unsigned32
	rcIpBgpPeerSooType	INTEGER
	rcIpBgpPeerRouteRefresh	EnableValue
	rcIpBgpPeerAsOverride	EnableValue
	rcIpBgpPeerAllowAsIn	INTEGER
	rcIpBgpPeerBfdEnable	EnableValue

RcIpBgpPeerGroupEntry
SEQUENCE
	rcIpBgpPeerGroupEnable	EnableValue
	rcIpBgpPeerGroupIndex	Integer32
	rcIpBgpPeerGroupGroupName	DisplayString
	rcIpBgpPeerGroupRemoteAs	Integer32
	rcIpBgpPeerGroupDefaultOriginate	INTEGER
	rcIpBgpPeerGroupEbgpMultiHop	INTEGER
	rcIpBgpPeerGroupAdvertisementInterval	Integer32
	rcIpBgpPeerGroupKeepAlive	Integer32
	rcIpBgpPeerGroupHoldTime	Integer32
	rcIpBgpPeerGroupWeight	Integer32
	rcIpBgpPeerGroupMaxPrefix	Integer32
	rcIpBgpPeerGroupNextHopSelf	TruthValue
	rcIpBgpPeerGroupRoutePolicyIn	DisplayString
	rcIpBgpPeerGroupRoutePolicyOut	DisplayString
	rcIpBgpPeerGroupRouteReflectorClient	TruthValue
	rcIpBgpPeerGroupSoftReconfigurationIn	EnableValue
	rcIpBgpPeerGroupSoftReconfiguration	INTEGER
	rcIpBgpPeerGroupPassword	DisplayString
	rcIpBgpPeerGroupRemovePrivateAs	EnableValue
	rcIpBgpPeerGroupRowStatus	RowStatus
	rcIpBgpPeerGroupMD5Authentication	EnableValue
	rcIpBgpPeerGroupSendCommunity	EnableValue
	rcIpBgpPeerGroupUpdateSourceInterface	IpAddress
	rcIpBgpPeerGroupVpnv4Address	EnableValue
	rcIpBgpPeerGroupIpvpnLiteCap	EnableValue
	rcIpBgpPeerGroupSooAddress	IpAddress
	rcIpBgpPeerGroupSooAsNumber	Integer32
	rcIpBgpPeerGroupSooAssignedNum	Unsigned32
	rcIpBgpPeerGroupSooType	INTEGER
	rcIpBgpPeerGroupRouteRefresh	EnableValue
	rcIpBgpPeerGroupAsOverride	EnableValue
	rcIpBgpPeerGroupAllowAsIn	Integer32
	rcIpBgpPeerGroupDefaultOriginateIpv6	TruthValue
	rcIpBgpPeerGroupAfUpdateSourceInterfaceType	InetAddressType
	rcIpBgpPeerGroupAfUpdateSourceInterface	InetAddress
	rcIpBgpPeerGroupIpv6Cap	EnableValue
	rcIpBgpPeerGroupIpv6RoutePolicyIn	DisplayString
	rcIpBgpPeerGroupIpv6RoutePolicyOut	DisplayString
	rcIpBgpPeerGroupBfdEnable	TruthValue

RcIpBgpDampenedPathAttrEntry
SEQUENCE
	rcIpBgpPathAttrPeer	IpAddress
	rcIpBgpPathAttrIpAddrPrefixLen	INTEGER
	rcIpBgpPathAttrIpAddrPrefix	IpAddress
	rcIpBgpPathAttrFlapPenalty	Integer32
	rcIpBgpPathAttrFlapCount	Integer32
	rcIpBgpPathAttrRouteDampened	INTEGER
	rcIpBgpPathAttrReuseTime	Integer32
	rcIpBgpPathAttrReuseTimeRemain	Integer32

RcIpBgp4PathAttrEntry
SEQUENCE
	rcIpBgp4PathAttrPeer	IpAddress
	rcIpBgp4PathAttrIpAddrPrefixLen	INTEGER
	rcIpBgp4PathAttrIpAddrPrefix	IpAddress
	rcIpBgp4PathAttrCommunities	OCTET STRING
	rcIpBgp4PathAttrOriginateId	IpAddress
	rcIpBgp4PathAttrClusterId	OCTET STRING

RcIpBgpExtAggregateAfEntry
SEQUENCE
	rcIpBgpExtAggregateAfAddressType	InetAddressType
	rcIpBgpExtAggregateAfAddress	InetAddress
	rcIpBgpExtAggregateAfPrefixLen	InetAddressPrefixLength
	rcIpBgpExtAggregateAfAsSetGenerate	TruthValue
	rcIpBgpExtAggregateAfSummaryOnly	TruthValue
	rcIpBgpExtAggregateAfSuppressPolicy	SnmpAdminString
	rcIpBgpExtAggregateAfAdvertisePolicy	SnmpAdminString
	rcIpBgpExtAggregateAfAttributePolicy	SnmpAdminString
	rcIpBgpExtAggregateAfRowStatus	RowStatus

RcIpBgpExtNetworkAfEntry
SEQUENCE
	rcIpBgpExtNetworkAfAddrType	InetAddressType
	rcIpBgpExtNetworkAfAddr	InetAddress
	rcIpBgpExtNetworkAfPrefixLen	InetAddressPrefixLength
	rcIpBgpExtNetworkAfMetric	Integer32
	rcIpBgpExtNetworkAfRowStatus	RowStatus

RcIpBgpExtPeerAfEntry
SEQUENCE
	rcIpBgpExtPeerAfGroupName	SnmpAdminString
	rcIpBgpExtPeerAfDefaultOriginate	TruthValue
	rcIpBgpExtPeerAfDefaultOriginateIpv6	TruthValue
	rcIpBgpExtPeerAfEbgpMultiHop	TruthValue
	rcIpBgpExtPeerAfAdvertisementInterval	Integer32
	rcIpBgpExtPeerAfPassword	SnmpAdminString
	rcIpBgpExtPeerAfWeight	Integer32
	rcIpBgpExtPeerAfMaxPrefix	Integer32
	rcIpBgpExtPeerAfNextHopSelf	TruthValue
	rcIpBgpExtPeerAfRoutePolicyIn	SnmpAdminString
	rcIpBgpExtPeerAfRoutePolicyOut	SnmpAdminString
	rcIpBgpExtPeerAfRouteReflectorClient	TruthValue
	rcIpBgpExtPeerAfSoftReconfigurationIn	TruthValue
	rcIpBgpExtPeerAfSoftReconfiguration	INTEGER
	rcIpBgpExtPeerAfRemovePrivateAs	TruthValue
	rcIpBgpExtPeerAfMD5Authentication	TruthValue
	rcIpBgpExtPeerAfDebugMask	Integer32
	rcIpBgpExtPeerAfSendCommunity	TruthValue
	rcIpBgpExtPeerAfUpdateSourceInterface	InetAddress
	rcIpBgpExtPeerAfVpnv4Address	TruthValue
	rcIpBgpExtPeerAfIpv6Cap	TruthValue
	rcIpBgpExtPeerAfIpvpnLiteCap	TruthValue
	rcIpBgpExtPeerAfSooAddress	IpAddress
	rcIpBgpExtPeerAfSooAsNumber	Integer32
	rcIpBgpExtPeerAfSooAssignedNum	Unsigned32
	rcIpBgpExtPeerAfSooType	INTEGER
	rcIpBgpExtPeerAfRouteRefresh	TruthValue
	rcIpBgpExtPeerAfAsOverride	TruthValue
	rcIpBgpExtPeerAfAllowAsIn	Integer32
	rcIpBgpExtPeerAfIpv6RoutePolicyIn	SnmpAdminString
	rcIpBgpExtPeerAfIpv6RoutePolicyOut	SnmpAdminString
	rcIpBgpExtPeerAfEnable	TruthValue
	rcIpBgpExtPeerAfRemoteAs	InetAutonomousSystemNumber
	rcIpBgpExtPeerAfConnectRetryInterval	Unsigned32
	rcIpBgpExtPeerAfHoldTimeConfigured	Unsigned32
	rcIpBgpExtPeerAfKeepAliveConfigured	Unsigned32
	rcIpBgpExtPeerAfRowStatus	RowStatus
	rcIpBgpExtPeerAfNewRemoteAs	OCTET STRING
	rcIpBgpExtPeerAfBfdEnable	TruthValue

RcIpBgpExtAfPathAttrEntry
SEQUENCE
	rcIpBgpExtAfPathAttrUnknown	OCTET STRING
	rcIpBgpExtAfPathAttrCommunities	OCTET STRING
	rcIpBgpExtAfPathAttrOriginateId	IpAddress
	rcIpBgpExtAfPathAttrClusterId	OCTET STRING

RcIpBgpTmpIdentifierTC
The representation of a BGP Identifier. BGP Identifiers are presented in the received network byte order. The BGP Identifier is displayed as if it is an IP address, even if it would be an illegal one.
TEXTUAL-CONVENTION
	OCTET STRING	Size(4)

RcIpBgpTmpAddressFamilyIdentifierTC
The representation of a BGP AFI
TEXTUAL-CONVENTION
	Unsigned32	0..65535

RcIpBgpTmpSubsequentAddressFamilyIdentifierTC
The representation of a BGP SAFI
TEXTUAL-CONVENTION
	Unsigned32	0..255

RcIpBgpTmpPeerAfEntry
SEQUENCE
	rcIpBgpTmpPeerAfInstance	Unsigned32
	rcIpBgpTmpPeerAfLocalAddrType	InetAddressType
	rcIpBgpTmpPeerAfLocalAddr	InetAddress
	rcIpBgpTmpPeerAfRemoteAddrType	InetAddressType
	rcIpBgpTmpPeerAfRemoteAddr	InetAddress
	rcIpBgpTmpPeerAfLocalPort	InetPortNumber
	rcIpBgpTmpPeerAfLocalAs	InetAutonomousSystemNumber
	rcIpBgpTmpPeerAfRemotePort	InetPortNumber
	rcIpBgpTmpPeerAfRemoteAs	InetAutonomousSystemNumber
	rcIpBgpTmpPeerAfIdentifier	RcIpBgpTmpIdentifierTC
	rcIpBgpTmpPeerAfAdminStatus	INTEGER
	rcIpBgpTmpPeerAfPeerState	INTEGER
	rcIpBgpTmpPeerAfConfiguredVersion	Unsigned32
	rcIpBgpTmpPeerAfNegotiatedVersion	Unsigned32

RcIpBgpTmpPeerAfErrorsEntry
SEQUENCE
	rcIpBgpTmpPeerAfLastErrorCodeReceived	OCTET STRING
	rcIpBgpTmpPeerAfLastErrorSubCodeReceived	OCTET STRING
	rcIpBgpTmpPeerAfLastErrorReceivedTime	TimeStamp
	rcIpBgpTmpPeerAfLastErrorReceivedText	SnmpAdminString
	rcIpBgpTmpPeerAfLastErrorReceivedData	OCTET STRING
	rcIpBgpTmpPeerAfLastErrorCodeSent	OCTET STRING
	rcIpBgpTmpPeerAfLastErrorSubCodeSent	OCTET STRING
	rcIpBgpTmpPeerAfLastErrorSentTime	TimeStamp
	rcIpBgpTmpPeerAfLastErrorSentText	SnmpAdminString
	rcIpBgpTmpPeerAfLastErrorSentData	OCTET STRING

RcIpBgpTmpPeerAfEventTimesEntry
SEQUENCE
	rcIpBgpTmpPeerAfFsmEstablishedTime	Gauge32
	rcIpBgpTmpPeerAfInUpdatesElapsedTime	Gauge32

RcIpBgpTmpPeerAfConfiguredTimersEntry
SEQUENCE
	rcIpBgpTmpPeerAfConnectRetryInterval	Unsigned32
	rcIpBgpTmpPeerAfHoldTimeConfigured	Unsigned32
	rcIpBgpTmpPeerAfKeepAliveConfigured	Unsigned32
	rcIpBgpTmpPeerAfMinASOrigInterval	Unsigned32
	rcIpBgpTmpPeerAfMinRouteAdverInterval	Unsigned32

RcIpBgpTmpPeerAfNegotiatedTimersEntry
SEQUENCE
	rcIpBgpTmpPeerAfHoldTime	Unsigned32
	rcIpBgpTmpPeerAfKeepAlive	Unsigned32

RcIpBgpTmpPeerAfCountersEntry
SEQUENCE
	rcIpBgpTmpPeerAfInUpdates	Counter32
	rcIpBgpTmpPeerAfOutUpdates	Counter32
	rcIpBgpTmpPeerAfInTotalMessages	Counter32
	rcIpBgpTmpPeerAfOutTotalMessages	Counter32
	rcIpBgpTmpPeerAfFsmEstablishedTransitions	Counter32

RcIpBgpTmpNlriEntry
SEQUENCE
	rcIpBgpTmpNlriIndex	Unsigned32
	rcIpBgpTmpNlriAfi	RcIpBgpTmpAddressFamilyIdentifierTC
	rcIpBgpTmpNlriSafi	RcIpBgpTmpSubsequentAddressFamilyIdentifierTC
	rcIpBgpTmpNlriPrefixType	InetAddressType
	rcIpBgpTmpNlriPrefix	InetAddress
	rcIpBgpTmpNlriPrefixLen	InetAddressPrefixLength
	rcIpBgpTmpNlriBest	TruthValue
	rcIpBgpTmpNlriCalcLocalPref	Unsigned32
	rcIpBgpTmpAfPathAttrIndex	Unsigned32
	rcIpBgpTmpAfPathAttrUnknownIndex	Unsigned32

RcIpBgpTmpAfPathAttrEntry
SEQUENCE
	rcIpBgpTmpAfPathAttrOrigin	INTEGER
	rcIpBgpTmpAfPathAttrNextHopAddrType	InetAddressType
	rcIpBgpTmpAfPathAttrNextHopAddr	InetAddress
	rcIpBgpTmpAfPathAttrLinkLocalNextHopAddrType	InetAddressType
	rcIpBgpTmpAfPathAttrLinkLocalNextHopAddr	InetAddress
	rcIpBgpTmpAfPathAttrMedPresent	TruthValue
	rcIpBgpTmpAfPathAttrMed	Unsigned32
	rcIpBgpTmpAfPathAttrLocalPref	Unsigned32
	rcIpBgpTmpAfPathAttrAtomicAggregate	INTEGER
	rcIpBgpTmpAfPathAttrAggregatorAS	InetAutonomousSystemNumber
	rcIpBgpTmpAfPathAttrAggregatorAddr	RcIpBgpTmpIdentifierTC
	rcIpBgpTmpAsPathCalcLength	Unsigned32
	rcIpBgpTmpAsPathIndex	Unsigned32
	rcIpBgpTmpAsPathString	SnmpAdminString

RcBfdTmpSessIndexTC
An index used to uniquely identify BFD sessions.
TEXTUAL-CONVENTION
	Unsigned32	1..4294967295

RcBfdTmpInterval
The BFD interval delay in microseconds.
TEXTUAL-CONVENTION
	Unsigned32	1..4294967295

RcBfdTmpDiag
A common BFD diagnostic code.
TEXTUAL-CONVENTION
	INTEGER	noDiagnostic(1), controlDetectionTimeExpired(2), echoFunctionFailed(3), neighborSignaledSessionDown(4), forwardingPlaneReset(5), pathDown(6), concatenatedPathDown(7), administrativelyDown(8), reverseConcatenatedPathDown(9)

RcBfdTmpSessEntry
SEQUENCE
	rcBfdTmpSessIndex	RcBfdTmpSessIndexTC
	rcBfdTmpSessApplicationId	Unsigned32
	rcBfdTmpSessDiscriminator	Unsigned32
	rcBfdTmpSessRemoteDiscr	Unsigned32
	rcBfdTmpSessUdpPort	InetPortNumber
	rcBfdTmpSessState	INTEGER
	rcBfdTmpSessRemoteHeardFlag	TruthValue
	rcBfdTmpSessDiag	Unsigned32
	rcBfdTmpSessOperMode	INTEGER
	rcBfdTmpSessDemandModeDesiredFlag	TruthValue
	rcBfdTmpSessEchoFuncModeDesiredFlag	TruthValue
	rcBfdTmpSessControlPlanIndepFlag	TruthValue
	rcBfdTmpSessAddrType	InetAddressType
	rcBfdTmpSessAddr	InetAddress
	rcBfdTmpSessDesiredMinTxInterval	RcBfdTmpInterval
	rcBfdTmpSessReqMinRxInterval	RcBfdTmpInterval
	rcBfdTmpSessReqMinEchoRxInterval	RcBfdTmpInterval
	rcBfdTmpSessDetectMult	Unsigned32
	rcBfdTmpSessStorType	StorageType
	rcBfdTmpSessRowStatus	RowStatus
	rcBfdTmpSessAuthPresFlag	TruthValue
	rcBfdTmpSessAuthenticationType	INTEGER

RcBfdTmpSessPerfEntry
SEQUENCE
	rcBfdTmpSessPerfPktIn	Counter32
	rcBfdTmpSessPerfPktOut	Counter32
	rcBfdTmpSessUpTime	TimeStamp
	rcBfdTmpSessPerfLastSessDownTime	TimeStamp
	rcBfdTmpSessPerfLastCommLostDiag	RcBfdTmpDiag
	rcBfdTmpSessPerfSessUpCount	Counter32
	rcBfdTmpSessPerfDiscTime	TimeStamp
	rcBfdTmpSessPerfPktInHC	Counter64
	rcBfdTmpSessPerfPktOutHC	Counter64

RcBfdTmpSessMapEntry
SEQUENCE
	rcBfdTmpSessMapBfdIndex	RcBfdTmpSessIndexTC

RcBfdExtSessEntry
SEQUENCE
	rcBfdExtSessPeerState	INTEGER
	rcBfdExtSessPeerAddrType	InetAddressType
	rcBfdExtSessPeerAddr	InetAddress
	rcBfdExtSessApp	SnmpAdminString
	rcBfdExtSessAppRun	SnmpAdminString

RcKhiChassisHistoryEntry
SEQUENCE
	rcKhiChassisHistoryIndex	Integer32
	rcKhiChassisHistoryTemperatureStateChange	KhiStatusValue
	rcKhiChassisHistoryTemperatureStateChangeTime	DateAndTime

RcKhiChassisFanEntry
SEQUENCE
	rcKhiChassisFanId	Integer32
	rcKhiChassisFanOperState	INTEGER
	rcKhiChassisFanFirstStateChange	INTEGER
	rcKhiChassisFanFirstStateChangeTime	DateAndTime
	rcKhiChassisFanOperStatusIndication	KhiStatusValue
	rcKhiChassisFanTemperature	Gauge32
	rcKhiChassisFanTempFirstHigherAlert	Gauge32
	rcKhiChassisFanTempFirstHigherAlertTime	DateAndTime
	rcKhiChassisFanTempStatusIndication	KhiStatusValue

RcKhiChassisFanOperHistoryEntry
SEQUENCE
	rcKhiChassisFanOperHistoryFanId	Integer32
	rcKhiChassisFanOperHistoryIndex	Integer32
	rcKhiChassisFanOperHistoryStateChange	KhiStatusValue
	rcKhiChassisFanOperHistoryStateChangeTime	DateAndTime

RcKhiChassisFanTempHistoryEntry
SEQUENCE
	rcKhiChassisFanTempHistoryFanId	Integer32
	rcKhiChassisFanTempHistoryIndex	Integer32
	rcKhiChassisFanTempHistoryTempStateChange	KhiStatusValue
	rcKhiChassisFanTempHistoryTempStateChangeTime	DateAndTime

RcKhiChassisPowerSupplyEntry
SEQUENCE
	rcKhiChassisPowerSupplyId	Integer32
	rcKhiChassisPowerSupplyOperState	INTEGER
	rcKhiChassisPowerSupplyFirstStateChange	INTEGER
	rcKhiChassisPowerSupplyFirstStateChangeTime	DateAndTime
	rcKhiChassisPowerSupplyStatusIndication	KhiStatusValue

RcKhiChassisPowerSupplyHistoryEntry
SEQUENCE
	rcKhiChassisPowerSupplyHistoryPSId	Integer32
	rcKhiChassisPowerSupplyHistoryIndex	Integer32
	rcKhiChassisPowerSupplyHistoryOperStateChange	KhiStatusValue
	rcKhiChassisPowerSupplyHistoryOperStateChangeTime	DateAndTime

RcKhiChassisLineCardEntry
SEQUENCE
	rcKhiChassisLineCardSlot	Integer32
	rcKhiChassisLineCardOperState	INTEGER
	rcKhiChassisLineCardAdminState	EnableValue
	rcKhiChassisLineCardFirstStateChange	KhiStatusValue
	rcKhiChassisLineCardFirstStateChangeTime	DateAndTime
	rcKhiChassisLineCardStatusIndication	KhiStatusValue

RcKhiChassisLineCardHistoryEntry
SEQUENCE
	rcKhiChassisLineCardHistoryLCId	Integer32
	rcKhiChassisLineCardHistoryIndex	Integer32
	rcKhiChassisLineCardHistoryOperStateChange	KhiStatusValue
	rcKhiChassisLineCardHistoryOperStateChangeTime	DateAndTime

RcKhiPerformanceSuspendedTaskEntry
SEQUENCE
	rcKhiPerformanceSuspendedTaskIndex	Integer32
	rcKhiPerformanceSuspendedTaskId	Integer32
	rcKhiPerformanceSuspendedTaskName	DisplayString
	rcKhiPerformanceSuspendedTaskSuspendedTime	DateAndTime

RcKhiPerformanceHistoryEntry
SEQUENCE
	rcKhiPerformanceHistoryIndex	Integer32
	rcKhiPerformanceHistoryCpuUtil	Gauge32
	rcKhiPerformanceHistoryCpuUtilTimeStamp	DateAndTime
	rcKhiPerformanceHistorySwitchFabricUtil	Gauge32
	rcKhiPerformanceHistorySwitchFabricUtilTimeStamp	DateAndTime
	rcKhiPerformanceHistoryOtherSwitchFabricUtil	Gauge32
	rcKhiPerformanceHistoryOtherSwitchFabricUtilTimeStamp	DateAndTime
	rcKhiPerformanceHistoryBufferUtil	Gauge32
	rcKhiPerformanceHistoryBufferUtilTimeStamp	DateAndTime
	rcKhiPerformanceHistoryDRamUsed	Gauge32
	rcKhiPerformanceHistoryDRamUsedTimeStamp	DateAndTime
	rcKhiPerformanceHistoryCPUControlTimeStamp	DateAndTime
	rcKhiPerformanceHistoryNoFBuf	Gauge32
	rcKhiPerformanceHistoryTxPacketsDropped	Gauge32
	rcKhiPerformanceHistoryOutError	Gauge32

RcKhiPortStateEventsHistoryEntry
SEQUENCE
	rcKhiPortStateEventsHistoryIndex	INTEGER
	rcKhiPortStateEventsHistoryTimestamp	DateAndTime
	rcKhiPortStateEventsHistoryPort	INTEGER
	rcKhiPortStateEventsHistoryEvent	INTEGER

RcKhiPortErrorsEventsEntry
SEQUENCE
	rcKhiPortErrorsEventsPortNum	INTEGER
	rcKhiPortErrorsEventsSingleCollisionErr	KhiStatusValue
	rcKhiPortErrorsEventsMultipleCollisionErr	KhiStatusValue
	rcKhiPortErrorsEventsLateCollisionErr	KhiStatusValue
	rcKhiPortErrorsEventsExcessiveCollisionErr	KhiStatusValue
	rcKhiPortErrorsEventsMacRxErr	KhiStatusValue
	rcKhiPortErrorsEventsMacTxErr	KhiStatusValue
	rcKhiPortErrorsEventsDeferTxErr	KhiStatusValue
	rcKhiPortErrorsEventsPacketErr	KhiStatusValue
	rcKhiPortErrorsEventsLinkInactiveErr	KhiStatusValue
	rcKhiPortErrorsEventsUnknownProtoErr	KhiStatusValue
	rcKhiPortErrorsEventsInFlwctrlErr	KhiStatusValue
	rcKhiPortErrorsEventsOutFlwctrlErr	KhiStatusValue
	rcKhiPortErrorsEventsAlignErr	KhiStatusValue
	rcKhiPortErrorsEventsFCSErr	KhiStatusValue
	rcKhiPortErrorsEventsFramesLongErr	KhiStatusValue
	rcKhiPortErrorsEventsTooShortErr	KhiStatusValue
	rcKhiPortErrorsEventsLinkFailureErr	KhiStatusValue
	rcKhiPortErrorsEventsCarrierSenseErr	KhiStatusValue
	rcKhiPortErrorsEventsCarrierErr	KhiStatusValue
	rcKhiPortErrorsEventsSQETestErr	KhiStatusValue

RcKhiPortErrorsHistoryEntry
SEQUENCE
	rcKhiPortErrorsHistoryIndex	INTEGER
	rcKhiPortErrorsHistoryTimestamp	DateAndTime
	rcKhiPortErrorsHistoryPort	INTEGER
	rcKhiPortErrorsHistoryErrorEvents	BITS

RcKhiForwardingAsicHealthEntry
SEQUENCE
	rcKhiForwardingAsicHealthSlotNumber	INTEGER
	rcKhiForwardingAsicHealthLeftLnIngBkPrsureRstCnt	Integer32
	rcKhiForwardingAsicHealthMidLnIngBkPrsureRstCnt	Integer32
	rcKhiForwardingAsicHealthRightLnIngBkPrsureRstCnt	Integer32
	rcKhiForwardingAsicHealthLeftLnIngBkPrsureRstStatus	KhiStatusValue
	rcKhiForwardingAsicHealthMidLnIngBkPrsureRstStatus	KhiStatusValue
	rcKhiForwardingAsicHealthRightLnIngBkPrsureRstStatus	KhiStatusValue
	rcKhiForwardingAsicHealthLeftLnIngSPIProtoRstCnt	Integer32
	rcKhiForwardingAsicHealthMidLnIngSPIProtoRstCnt	Integer32
	rcKhiForwardingAsicHealthRightLnIngSPIProtoRstCnt	Integer32
	rcKhiForwardingAsicHealthLeftLnIngSPIProtoRstStatus	KhiStatusValue
	rcKhiForwardingAsicHealthMidLnIngSPIProtoRstStatus	KhiStatusValue
	rcKhiForwardingAsicHealthRightLnIngSPIProtoRstStatus	KhiStatusValue
	rcKhiForwardingAsicHealthLeftLnIngSPIDefragCnt	Integer32
	rcKhiForwardingAsicHealthMidLnIngSPIDefragCnt	Integer32
	rcKhiForwardingAsicHealthRightLnIngSPIDefragCnt	Integer32
	rcKhiForwardingAsicHealthLeftLnIngSPIDefragStatus	KhiStatusValue
	rcKhiForwardingAsicHealthMidLnIngSPIDefragStatus	KhiStatusValue
	rcKhiForwardingAsicHealthRightLnIngSPIDefragStatus	KhiStatusValue
	rcKhiForwardingAsicHealthLeftLnEgrMcastQFullRstCnt	Integer32
	rcKhiForwardingAsicHealthMidLnEgrMcastQFullRstCnt	Integer32
	rcKhiForwardingAsicHealthRightLnEgrMcastQFullRstCnt	Integer32
	rcKhiForwardingAsicHealthLeftLnEgrMcastQFullRstStatus	KhiStatusValue
	rcKhiForwardingAsicHealthMidLnEgrMcastQFullRstStatus	KhiStatusValue
	rcKhiForwardingAsicHealthRightLnEgrMcastQFullRstStatus	KhiStatusValue
	rcKhiForwardingAsicHealthLeftLnEgrFreePgErrRstCnt	Integer32
	rcKhiForwardingAsicHealthMidLnEgrFreePgErrRstCnt	Integer32
	rcKhiForwardingAsicHealthRightLnEgrFreePgErrRstCnt	Integer32
	rcKhiForwardingAsicHealthLeftLnEgrFreePgErrRstStatus	KhiStatusValue
	rcKhiForwardingAsicHealthMidLnEgrFreePgErrRstStatus	KhiStatusValue
	rcKhiForwardingAsicHealthRightLnEgrFreePgErrRstStatus	KhiStatusValue
	rcKhiForwardingAsicHealthLeftLnEgrUcastQFullRstCnt	Integer32
	rcKhiForwardingAsicHealthMidLnEgrUcastQFullRstCnt	Integer32
	rcKhiForwardingAsicHealthRightLnEgrUcastQFullRstCnt	Integer32
	rcKhiForwardingAsicHealthLeftLnEgrUcastQFullRstStatus	KhiStatusValue
	rcKhiForwardingAsicHealthMidLnEgrUcastQFullRstStatus	KhiStatusValue
	rcKhiForwardingAsicHealthRightLnEgrUcastQFullRstStatus	KhiStatusValue
	rcKhiForwardingAsicHealthLeftLnEgrFreePgLwrLmtRstCnt	Integer32
	rcKhiForwardingAsicHealthMidLnEgrFreePgLwrLmtRstCnt	Integer32
	rcKhiForwardingAsicHealthRightLnEgrFreePgLwrLmtRstCnt	Integer32
	rcKhiForwardingAsicHealthLeftLnEgrFreePgLwrLmtStatus	KhiStatusValue
	rcKhiForwardingAsicHealthMidLnEgrFreePgLwrLmtStatus	KhiStatusValue
	rcKhiForwardingAsicHealthRightLnEgrFreePgLwrLmtStatus	KhiStatusValue
	rcKhiForwardingAsicHealthLeftLnEgrRepIDMismatchRstCnt	Integer32
	rcKhiForwardingAsicHealthMidLnEgrRepIDMismatchRstCnt	Integer32
	rcKhiForwardingAsicHealthRightLnEgrRepIDMismatchRstCnt	Integer32
	rcKhiForwardingAsicHealthLeftLnEgrRepIDMismatchStatus	KhiStatusValue
	rcKhiForwardingAsicHealthMidLnEgrRepIDMismatchStatus	KhiStatusValue
	rcKhiForwardingAsicHealthRightLnEgrRepIDMismatchStatus	KhiStatusValue
	rcKhiForwardingAsicHealthLeftLnEgrNoBeepBeepRstCnt	Integer32
	rcKhiForwardingAsicHealthMidLnEgrNoBeepBeepRstCnt	Integer32
	rcKhiForwardingAsicHealthRightLnEgrNoBeepBeepRstCnt	Integer32
	rcKhiForwardingAsicHealthLeftLnEgrNoBeepBeepStatus	KhiStatusValue
	rcKhiForwardingAsicHealthMidLnEgrNoBeepBeepStatus	KhiStatusValue
	rcKhiForwardingAsicHealthRightLnEgrNoBeepBeepStatus	KhiStatusValue

RcKhiForwardingRSPStateEntry
SEQUENCE
	rcKhiForwardingRSPStateSlotNumber	INTEGER
	rcKhiForwardingRSPStateDirection	INTEGER
	rcKhiForwardingRSPStateLeftLnErrMask	BITS
	rcKhiForwardingRSPStateMidLnErrMask	BITS
	rcKhiForwardingRSPStateRightLnErrMask	BITS
	rcKhiForwardingRSPStateLeftLnHealthStatus	KhiStatusValue
	rcKhiForwardingRSPStateMidLnHealthStatus	KhiStatusValue
	rcKhiForwardingRSPStateRightLnHealthStatus	KhiStatusValue

RcKhiForwardingRSPStatsEntry
SEQUENCE
	rcKhiForwardingRSPStatsSlotNumber	INTEGER
	rcKhiForwardingRSPStatsDirection	INTEGER
	rcKhiForwardingRSPStatsLeftLnTotalAMPkts	Counter64
	rcKhiForwardingRSPStatsMidLnTotalAMPkts	Counter64
	rcKhiForwardingRSPStatsRightLnTotalAMPkts	Counter64
	rcKhiForwardingRSPStatsLeftLnTotalAMRxErrPkts	Counter64
	rcKhiForwardingRSPStatsMidLnTotalAMRxErrPkts	Counter64
	rcKhiForwardingRSPStatsRightLnTotalAMRxErrPkts	Counter64
	rcKhiForwardingRSPStatsLeftLnAMRxErrPktsStatus	KhiStatusValue
	rcKhiForwardingRSPStatsMidLnAMRxErrPktsStatus	KhiStatusValue
	rcKhiForwardingRSPStatsRightLnAMRxErrPktsStatus	KhiStatusValue
	rcKhiForwardingRSPStatsLeftLnTotalAMShortPkts	Counter64
	rcKhiForwardingRSPStatsMidLnTotalAMShortPkts	Counter64
	rcKhiForwardingRSPStatsRightLnTotalAMShortPkts	Counter64
	rcKhiForwardingRSPStatsLeftLnAMShortPktsStatus	KhiStatusValue
	rcKhiForwardingRSPStatsMidLnAMShortPktsStatus	KhiStatusValue
	rcKhiForwardingRSPStatsRightLnAMShortPktsStatus	KhiStatusValue
	rcKhiForwardingRSPStatsLeftLnTotalAMCongestionDrops	Counter64
	rcKhiForwardingRSPStatsMidLnTotalAMCongestionDrops	Counter64
	rcKhiForwardingRSPStatsRightLnTotalAMCongestionDrops	Counter64
	rcKhiForwardingRSPStatsLeftLnAMCongestionDropStatus	KhiStatusValue
	rcKhiForwardingRSPStatsMidLnAMCongestionDropStatus	KhiStatusValue
	rcKhiForwardingRSPStatsRightLnAMCongestionDropStatus	KhiStatusValue
	rcKhiForwardingRSPStatsLeftLnTotalAMProcErrPkts	Counter64
	rcKhiForwardingRSPStatsMidLnTotalAMProcErrPkts	Counter64
	rcKhiForwardingRSPStatsRightLnTotalAMProcErrPkts	Counter64
	rcKhiForwardingRSPStatsLeftLnAMProcErrPktsStatus	KhiStatusValue
	rcKhiForwardingRSPStatsMidLnAMProcErrPktsStatus	KhiStatusValue
	rcKhiForwardingRSPStatsRightLnAMProcErrPktsStatus	KhiStatusValue
	rcKhiForwardingRSPStatsLeftLnTotalAMExpPkts	Counter64
	rcKhiForwardingRSPStatsMidLnTotalAMExpPkts	Counter64
	rcKhiForwardingRSPStatsRightLnTotalAMExpPkts	Counter64
	rcKhiForwardingRSPStatsLeftLnAMExpPktsStatus	KhiStatusValue
	rcKhiForwardingRSPStatsMidLnAMExpPktsStatus	KhiStatusValue
	rcKhiForwardingRSPStatsRightLnAMExpPktsStatus	KhiStatusValue
	rcKhiForwardingRSPStatsLeftLnTotalPMFwdPkts	Counter64
	rcKhiForwardingRSPStatsMidLnTotalPMFwdPkts	Counter64
	rcKhiForwardingRSPStatsRightLnTotalPMFwdPkts	Counter64
	rcKhiForwardingRSPStatsLeftLnTotalPMDropErrPkts	Counter64
	rcKhiForwardingRSPStatsMidLnTotalPMDropErrPkts	Counter64
	rcKhiForwardingRSPStatsRightLnTotalPMDropErrPkts	Counter64
	rcKhiForwardingRSPStatsLeftLnPMDropErrStatus	KhiStatusValue
	rcKhiForwardingRSPStatsMidLnPMDropErrStatus	KhiStatusValue
	rcKhiForwardingRSPStatsRightLnPMDropErrStatus	KhiStatusValue

RcKhiForwardingF2XHealthEntry
SEQUENCE
	rcKhiForwardingF2XHealthSlotNumber	INTEGER
	rcKhiForwardingF2XHealthLeftLnErrMask	BITS
	rcKhiForwardingF2XHealthMidLnErrMask	BITS
	rcKhiForwardingF2XHealthRightLnErrMask	BITS
	rcKhiForwardingF2XHealthLeftLnHealthStatus	KhiStatusValue
	rcKhiForwardingF2XHealthMidLnHealthStatus	KhiStatusValue
	rcKhiForwardingF2XHealthRightLnHealthStatus	KhiStatusValue

RcKhiForwardingHistoryEntry
SEQUENCE
	rcKhiForwardingHistoryIndex	INTEGER
	rcKhiForwardingHistoryTimeStamp	DateAndTime
	rcKhiForwardingHistorySlotNumber	INTEGER
	rcKhiForwardingHistoryLane	INTEGER
	rcKhiForwardingHistoryEvent	DisplayString

RcKhiForwardingCurrentStatusEntry
SEQUENCE
	rcKhiForwardingCurrentStatusSlotNumber	INTEGER
	rcKhiForwardingCurrentStatusLeftLnHealth	KhiStatusValue
	rcKhiForwardingCurrentStatusLeftLnErrMask	BITS
	rcKhiForwardingCurrentStatusMidLnHealth	KhiStatusValue
	rcKhiForwardingCurrentStatusMidLnErrMask	BITS
	rcKhiForwardingCurrentStatusRightLnHealth	KhiStatusValue
	rcKhiForwardingCurrentStatusRightLnErrMask	BITS

RcKhiOspfEntry
SEQUENCE
	rcKhiOspfVrfId	Integer32
	rcKhiOspfRouteTableSize	Counter32
	rcKhiOspfRefRouteTableSize	Counter32
	rcKhiOspfLsdbTableSize	Counter32
	rcKhiOspfNumOfInterfaces	Counter32
	rcKhiOspfNumOfAdjacency	Counter32
	rcKhiOspfRefNumOfAdjacency	Counter32
	rcKhiOspfLastClearTimestamp	DateAndTime
	rcKhiOspfFirstEventTimestamp	DateAndTime

RcKhiOspfHistoryEntry
SEQUENCE
	rcKhiOspfHistoryVrfId	Integer32
	rcKhiOspfHistoryIndex	Integer32
	rcKhiOspfHistoryLsdbTableSize	Counter32
	rcKhiOspfHistoryNumOfAdjacency	Counter32
	rcKhiOspfHistoryTimestamp	DateAndTime

RcKhiBgpEntry
SEQUENCE
	rcKhiBgpVrfId	Integer32
	rcKhiBgpUpdateSent	Counter32
	rcKhiBgpUpdateRecvd	Counter32
	rcKhiBgpNotifySent	Counter32
	rcKhiBgpNotifyRecvd	Counter32
	rcKhiBgpBadEvents	Counter32
	rcKhiBgpRouteTableSize	Counter32
	rcKhiBgpRefRouteTableSize	Counter32
	rcKhiBgpEstablishedNbrs	Counter32
	rcKhiBgpRefEstablishedNbrs	Counter32
	rcKhiBgpNumOfAggregates	Counter32
	rcKhiBgpNumOfImportedRoutes	Counter32
	rcKhiBgpLastClearTimestamp	DateAndTime
	rcKhiBgpFirstEventTimestamp	DateAndTime

RcKhiBgpHistoryEntry
SEQUENCE
	rcKhiBgpHistoryVrfId	Integer32
	rcKhiBgpHistoryIndex	Integer32
	rcKhiBgpHistoryRibCount	Counter32
	rcKhiBgpHistoryNumOfPeers	Counter32
	rcKhiBgpHistoryTimestamp	DateAndTime

RcKhiPimEntry
SEQUENCE
	rcKhiPimVrfId	Integer32
	rcKhiPimRoutes	Counter32
	rcKhiPimRefRoutes	Counter32
	rcKhiPimAdjacencies	Counter32
	rcKhiPimRefAdjacencies	Counter32
	rcKhiPimLastClearTimestamp	DateAndTime
	rcKhiPimFirstEventTimestamp	DateAndTime

RcKhiPimHistoryEntry
SEQUENCE
	rcKhiPimHistoryVrfId	Integer32
	rcKhiPimHistoryIndex	Integer32
	rcKhiPimHistoryRouteCount	Counter32
	rcKhiPimHistoryAdjacencies	Counter32
	rcKhiPimHistoryTimestamp	DateAndTime

RcKhiIgmpHistoryEntry
SEQUENCE
	rcKhiIgmpHistoryVrfId	Integer32
	rcKhiIgmpHistoryIndex	Integer32
	rcKhiIgmpHistoryGroupCount	Counter32
	rcKhiIgmpHistorySenderCount	Counter32
	rcKhiIgmpHistoryTimestamp	DateAndTime

RcKhiIgmpSnoopHistoryEntry
SEQUENCE
	rcKhiIgmpSnoopHistoryVrfId	Integer32
	rcKhiIgmpSnoopHistoryIndex	Integer32
	rcKhiIgmpSnoopHistoryStreamCount	Counter32
	rcKhiIgmpSnoopHistoryHostCount	Counter32
	rcKhiIgmpSnoopHistoryTimestamp	DateAndTime

RcKhiIstHistoryEntry
SEQUENCE
	rcKhiIstHistoryIndex	Integer32
	rcKhiIstHistoryIstStatus	KhiStatusValue
	rcKhiIstHistoryTimestamp	DateAndTime

RcKhiSmltHistoryEntry
SEQUENCE
	rcKhiSmltHistoryIndex	Integer32
	rcKhiSmltHistorySmltId	Integer32
	rcKhiSmltHistorySmltStatus	KhiStatusValue
	rcKhiSmltHistoryTimestamp	DateAndTime

RcKhiSmltEntry
SEQUENCE
	rcKhiSmltId	Integer32
	rcKhiSmltStatus	KhiStatusValue
	rcKhiSmltUpEvents	Counter32
	rcKhiSmltDownEvents	Counter32

RcKhiMgmtLogHistoryEntry
SEQUENCE
	rcKhiMgmtLogHistoryIndex	Integer32
	rcKhiMgmtLogHistoryStatus	KhiStatusValue
	rcKhiMgmtLogHistoryTimestamp	DateAndTime

RcKhiIpInterfaceHistoryEntry
SEQUENCE
	rcKhiIpInterfaceHistoryIndex	INTEGER
	rcKhiIpInterfaceHistoryTimestamp	DateAndTime
	rcKhiIpInterfaceHistoryIpAddr	IpAddress
	rcKhiIpInterfaceHistoryVlanId	INTEGER
	rcKhiIpInterfaceHistoryEvent	INTEGER

RcIpMplsIfEntry
SEQUENCE
	rcIpMplsIfIfIndex	InterfaceIndexOrZero
	rcIpMplsIfLdpAdminState	EnableValue
	rcIpMplsIfLdpSessionKeepAlive	Unsigned32
	rcIpMplsIfLdpHelloHoldTime	Unsigned32
	rcIpMplsIfLdpTransportAddr	INTEGER
	rcIpMplsIfLdpImportPolicy	INTEGER
	rcIpMplsIfRsvpAdminState	EnableValue
	rcIpMplsIfRefreshReduction	INTEGER
	rcIpMplsIfRefreshInterval	Unsigned32
	rcIpMplsIfRefreshMultiplier	Unsigned32
	rcIpMplsIfRsvpHelloInterval	Unsigned32
	rcIpMplsIfMessageBundling	INTEGER
	rcIpMplsIfMtu	Unsigned32
	rcIpMplsIfRowStatus	RowStatus

RcIpInterVrfStaticRouteEntry
SEQUENCE
	rcIpInterVrfStaticRouteOwnerVrfId	VrfIdentifier
	rcIpInterVrfStaticRouteDest	IpAddress
	rcIpInterVrfStaticRouteMask	IpAddress
	rcIpInterVrfStaticRouteNextHop	IpAddress
	rcIpInterVrfStaticRouteMetric	INTEGER
	rcIpInterVrfStaticRouteIfIndex	InterfaceIndex
	rcIpInterVrfStaticRoutePreference	INTEGER
	rcIpInterVrfStaticRouteEnable	TruthValue
	rcIpInterVrfStaticRouteStatus	INTEGER
	rcIpInterVrfStaticRouteRowStatus	RowStatus
	rcIpInterVrfStaticRouteLocalNextHop	TruthValue
	rcIpInterVrfStaticRouteNextHopVrfId	VrfIdentifier

RcIpStaticMRouteEntry
SEQUENCE
	rcIpStaticMRouteIpAddressType	InetAddressType
	rcIpStaticMRouteIpAddress	InetAddress
	rcIpStaticMRouteMask	InetAddressPrefixLength
	rcIpStaticMRouteRpfAddressType	InetAddressType
	rcIpStaticMRouteRpfAddress	InetAddress
	rcIpStaticMRoutePreference	Unsigned32
	rcIpStaticMRouteEnable	TruthValue
	rcIpStaticMRouteRowStatus	RowStatus

RcIpEcmpRouteEntry
SEQUENCE
	rcIpEcmpRouteSrcIp	IpAddress
	rcIpEcmpRouteDstIp	IpAddress
	rcIpEcmpRouteDstMask	IpAddress
	rcIpEcmpRouteNextHopLegacy	IpAddress
	rcIpEcmpRouteNextHopRMod	IpAddress

RcIPClearIPMCRecordEntry
SEQUENCE
	rcIPClearIPMCRecordGroup	IpAddress
	rcIPClearIPMCRecordVlanId	INTEGER
	rcIPClearIPMCRecordSource	IpAddress
	rcIPClearIPMCRecordLCForceDelete	TruthValue

RcIPClearArpRecordEntry
SEQUENCE
	rcIPClearArpRecordIpAddr	IpAddress
	rcIPClearArpRecordVlanId	INTEGER
	rcIPClearArpRecordLCForceDelete	TruthValue

RcArpExtEntry
SEQUENCE
	rcArpExtEntIfIndex	InterfaceIndex
	rcArpExtEntDoProxy	INTEGER
	rcArpExtEntDoResp	INTEGER
	rcArpExtEntDoFlood	INTEGER

RcArpExtV2Entry
SEQUENCE
	rcArpExtV2EntIfIndex	InterfaceIndex
	rcArpExtV2EntIpIfAddr	IpAddress
	rcArpExtV2EntDoProxy	INTEGER
	rcArpExtV2EntDoResp	INTEGER

RcRipExtEntry
SEQUENCE
	rcRipExtEntIfIndex	InterfaceIndex
	rcRipExtEntTalk	INTEGER
	rcRipExtEntListen	INTEGER
	rcRipExtEntPoison	INTEGER

RcRipExtV2Entry
SEQUENCE
	rcRipExtV2EntIfIndex	InterfaceIndex
	rcRipExtV2EntIpIfAddr	IpAddress
	rcRipExtV2EntTalk	INTEGER
	rcRipExtV2EntListen	INTEGER
	rcRipExtV2EntPoison	INTEGER

RcTestEntry
SEQUENCE
	rcTestExtIfIndex	InterfaceIndex
	rcTestExtPassCount	Integer32
	rcTestExtFailCount	Integer32

RcStatEntry
SEQUENCE
	rcStatPortIndex	InterfaceIndex
	rcStatFrameTooShorts	Counter32
	rcStatBridgeInUnicastFrames	Counter32
	rcStatBridgeInMulticastFrames	Counter32
	rcStatBridgeInBroadcastFrames	Counter32
	rcStatBridgeInDiscards	Counter32
	rcStatBridgeOutUnicastFrames	Counter32
	rcStatBridgeOutMulticastFrames	Counter32
	rcStatBridgeOutBroadcastFrames	Counter32
	rcStatRouteInUnicastFrames	Counter32
	rcStatRouteInMulticastFrames	Counter32
	rcStatRouteInDiscards	Counter32
	rcStatRouteOutUnicastFrames	Counter32
	rcStatRouteOutMulticastFrames	Counter32
	rcStatStgForwardTransitions	Counter32
	rcStatStgInConfigBpdus	Counter32
	rcStatStgInTcnBpdus	Counter32
	rcStatStgInBadBpdus	Counter32
	rcStatStgOutConfigBpdus	Counter32
	rcStatStgOutTcnBpdus	Counter32
	rcStatBridgeOutFrames	Counter32

RcStatGigEntry
SEQUENCE
	rcStatGigPortIndex	InterfaceIndex
	rcStatGigLinkFailures	Counter32
	rcStatGigPacketErrors	Counter32
	rcStatGigCarrierErrors	Counter32
	rcStatGigLinkInactiveErrors	Counter32
	rcStatGigInFlowCtrlPkts	Counter32
	rcStatGigOutFlowCtrlPkts	Counter32

RcStatOspfIfEntry
SEQUENCE
	rcStatOspfIfIndex	InterfaceIndexOrZero
	rcStatOspfIfRxHellos	Counter32
	rcStatOspfIfRxDBDescrs	Counter32
	rcStatOspfIfRxLSUpdates	Counter32
	rcStatOspfIfRxLSReqs	Counter32
	rcStatOspfIfRxLSAcks	Counter32
	rcStatOspfIfTxHellos	Counter32
	rcStatOspfIfTxDBDescrs	Counter32
	rcStatOspfIfTxLSUpdates	Counter32
	rcStatOspfIfTxLSReqs	Counter32
	rcStatOspfIfTxLSAcks	Counter32
	rcStatOspfIfVersionMismatches	Counter32
	rcStatOspfIfAreaMismatches	Counter32
	rcStatOspfIfAuthTypeMismatches	Counter32
	rcStatOspfIfAuthFailures	Counter32
	rcStatOspfIfNetMaskMismatches	Counter32
	rcStatOspfIfHelloIntervalMismatches	Counter32
	rcStatOspfIfDeadIntervalMismatches	Counter32
	rcStatOspfIfOptionMismatches	Counter32

RcStatMltIfExtnEntry
SEQUENCE
	rcStatMltIfExtnMltId	INTEGER
	rcStatMltIfExtnIfInMulticastPkts	Counter32
	rcStatMltIfExtnIfInBroadcastPkts	Counter32
	rcStatMltIfExtnIfOutMulticastPkts	Counter32
	rcStatMltIfExtnIfOutBroadcastPkts	Counter32
	rcStatMltIfExtnIfHCInOctets	Counter64
	rcStatMltIfExtnIfHCInUcastPkts	Counter64
	rcStatMltIfExtnIfHCInMulticastPkt	Counter64
	rcStatMltIfExtnIfHCInBroadcastPkt	Counter64
	rcStatMltIfExtnIfHCOutOctets	Counter64
	rcStatMltIfExtnIfHCOutUcastPkts	Counter64
	rcStatMltIfExtnIfHCOutMulticast	Counter64
	rcStatMltIfExtnIfHCOutBroadcast	Counter64

RcStatMltEtherEntry
SEQUENCE
	rcStatMltEtherMltId	INTEGER
	rcStatMltEtherAlignmentErrors	Counter32
	rcStatMltEtherFCSErrors	Counter32
	rcStatMltEtherSingleCollFrames	Counter32
	rcStatMltEtherMultipleCollFrames	Counter32
	rcStatMltEtherSQETestError	Counter32
	rcStatMltEtherDeferredTransmiss	Counter32
	rcStatMltEtherLateCollisions	Counter32
	rcStatMltEtherExcessiveCollis	Counter32
	rcStatMltEtherIMacTransmitError	Counter32
	rcStatMltEtherCarrierSenseError	Counter32
	rcStatMltEtherFrameTooLong	Counter32
	rcStatMltEtherIMacReceiveError	Counter32

RcStatMltIpEntry
SEQUENCE
	rcStatMltIpMltId	INTEGER
	rcStatMltIpInReceives	Counter32
	rcStatMltIpInHdrErrors	Counter32
	rcStatMltIpInAddrErrors	Counter32
	rcStatMltIpForwDatagrams	Counter32
	rcStatMltIpInUnknownProtos	Counter32
	rcStatMltIpInDiscards	Counter32
	rcStatMltIpInDelivers	Counter32
	rcStatMltIpOutRequest	Counter32
	rcStatMltIpOutDiscards	Counter32
	rcStatMltIpOutNoRoutes	Counter32
	rcStatMltIpReasmReqds	Counter32
	rcStatMltIpReasmOKs	Counter32
	rcStatMltIpReasmFails	Counter32
	rcStatMltIpFragOKs	Counter32
	rcStatMltIpFragFails	Counter32
	rcStatMltIpFragCreates	Counter32
	rcStatMltIpRoutingDiscards	Counter32

RcStatOspfIfV2Entry
SEQUENCE
	rcStatOspfIfV2Index	InterfaceIndexOrZero
	rcStatOspfIfV2Addr	IpAddress
	rcStatOspfIfV2RxHellos	Counter32
	rcStatOspfIfV2RxDBDescrs	Counter32
	rcStatOspfIfV2RxLSUpdates	Counter32
	rcStatOspfIfV2RxLSReqs	Counter32
	rcStatOspfIfV2RxLSAcks	Counter32
	rcStatOspfIfV2TxHellos	Counter32
	rcStatOspfIfV2TxDBDescrs	Counter32
	rcStatOspfIfV2TxLSUpdates	Counter32
	rcStatOspfIfV2TxLSReqs	Counter32
	rcStatOspfIfV2TxLSAcks	Counter32
	rcStatOspfIfV2VersionMismatches	Counter32
	rcStatOspfIfV2AreaMismatches	Counter32
	rcStatOspfIfV2AuthTypeMismatches	Counter32
	rcStatOspfIfV2AuthFailures	Counter32
	rcStatOspfIfV2NetMaskMismatches	Counter32
	rcStatOspfIfV2HelloIntervalMismatches	Counter32
	rcStatOspfIfV2DeadIntervalMismatches	Counter32
	rcStatOspfIfV2OptionMismatches	Counter32

RcStatPosControlEntry
SEQUENCE
	rcStatPosControlPortIndex	InterfaceIndex
	rcStatPosControlInErrors	Counter32
	rcStatPosControlInUnknownProtos	Counter32
	rcStatPosControlOutErrors	Counter32
	rcStatPosControlHCInOctets	Counter64
	rcStatPosControlHCInUcastPkts	Counter64
	rcStatPosControlHCInMulticastPkts	Counter64
	rcStatPosControlHCInBroadcastPkts	Counter64
	rcStatPosControlHCInDiscards	Counter64
	rcStatPosControlHCOutOctets	Counter64
	rcStatPosControlHCOutUcastPkts	Counter64
	rcStatPosControlHCOutMulticastPkts	Counter64
	rcStatPosControlHCOutBroadcastPkts	Counter64
	rcStatPosControlHCOutDiscards	Counter64

RcStatBgpPeerEntry
SEQUENCE
	rcStatBgpPeerAddr	IpAddress
	rcStatBgpPeerStarts	Counter32
	rcStatBgpPeerStops	Counter32
	rcStatBgpPeerOpens	Counter32
	rcStatBgpPeerCloses	Counter32
	rcStatBgpPeerFails	Counter32
	rcStatBgpPeerFatals	Counter32
	rcStatBgpPeerConnExps	Counter32
	rcStatBgpPeerHoldExps	Counter32
	rcStatBgpPeerKeepExps	Counter32
	rcStatBgpPeerTxMsgs	Counter32
	rcStatBgpPeerTxOpens	Counter32
	rcStatBgpPeerTxKeeps	Counter32
	rcStatBgpPeerTxUpdates	Counter32
	rcStatBgpPeerTxNotifys	Counter32
	rcStatBgpPeerRxMsgs	Counter32
	rcStatBgpPeerRxInCompPkts	Counter32
	rcStatBgpPeerRxOpens	Counter32
	rcStatBgpPeerRxKeeps	Counter32
	rcStatBgpPeerRxUpdates	Counter32
	rcStatBgpPeerRxNotifys	Counter32
	rcStatBgpPeerBadEvents	Counter32
	rcStatBgpPeerSyncFails	Counter32
	rcStatBgpPeerRcvdTooShort	Counter32
	rcStatBgpPeerNoMarker	Counter32
	rcStatBgpPeerDropped	Counter32
	rcStatBgpPeerBadMsgTypes	Counter32
	rcStatBgpPeerTrEvent	Counter32
	rcStatBgpPeerTxRoutes	Counter32
	rcStatBgpPeerRxRoutesAdded	Counter32
	rcStatBgpPeerRxRoutesReplaced	Counter32
	rcStatBgpPeerRxNlri	Counter32
	rcStatBgpPeerRxValidUpdates	Counter32
	rcStatBgpPeerRxECodeHeader	Counter32
	rcStatBgpPeerRxECodeOpen	Counter32
	rcStatBgpPeerRxECodeUpdate	Counter32
	rcStatBgpPeerRxECodeHoldtimer	Counter32
	rcStatBgpPeerRxECodeFSM	Counter32
	rcStatBgpPeerRxECodeCease	Counter32
	rcStatBgpPeerRxHdrCodeNoSync	Counter32
	rcStatBgpPeerRxHdrCodeInvalidMsgLen	Counter32
	rcStatBgpPeerRxHdrCodeInvalidMsgType	Counter32
	rcStatBgpPeerRxOpCodeBadVer	Counter32
	rcStatBgpPeerRxOpCodeBadAs	Counter32
	rcStatBgpPeerRxOpCodeBadRtID	Counter32
	rcStatBgpPeerRxOpCodeUnsuppOption	Counter32
	rcStatBgpPeerRxOpCodeAuthFail	Counter32
	rcStatBgpPeerRxOpCodeBadHold	Counter32
	rcStatBgpPeerRxUpdCodeMalformedAttrList	Counter32
	rcStatBgpPeerRxUpdCodeWelknownAttrUnrecog	Counter32
	rcStatBgpPeerRxUpdCodeWelknownAttrMiss	Counter32
	rcStatBgpPeerRxUpdCodeAttrFlagError	Counter32
	rcStatBgpPeerRxUpdCodeAttrLenError	Counter32
	rcStatBgpPeerRxUpdCodeBadORIGINAttr	Counter32
	rcStatBgpPeerRxUpdCodeASRoutingLoop	Counter32
	rcStatBgpPeerRxUpdCodeBadNHAttr	Counter32
	rcStatBgpPeerRxUpdCodeOptionalAttrError	Counter32
	rcStatBgpPeerRxUpdCodeBadNetworkField	Counter32
	rcStatBgpPeerRxUpdCodeMalformedASPath	Counter32
	rcStatBgpPeerTxECodeHeader	Counter32
	rcStatBgpPeerTxECodeOpen	Counter32
	rcStatBgpPeerTxECodeUpdate	Counter32
	rcStatBgpPeerTxECodeHoldtimer	Counter32
	rcStatBgpPeerTxECodeFSM	Counter32
	rcStatBgpPeerTxECodeCease	Counter32
	rcStatBgpPeerTxHdrCodeNoSync	Counter32
	rcStatBgpPeerTxHdrCodeInvalidMsgLen	Counter32
	rcStatBgpPeerTxHdrCodeInvalidMsgType	Counter32
	rcStatBgpPeerTxOpCodeBadVer	Counter32
	rcStatBgpPeerTxOpCodeBadAs	Counter32
	rcStatBgpPeerTxOpCodeBadRtID	Counter32
	rcStatBgpPeerTxOpCodeUnsuppOption	Counter32
	rcStatBgpPeerTxOpCodeAuthFail	Counter32
	rcStatBgpPeerTxOpCodeBadHold	Counter32
	rcStatBgpPeerTxUpdCodeMalformedAttrList	Counter32
	rcStatBgpPeerTxUpdCodeWelknownAttrUnrecog	Counter32
	rcStatBgpPeerTxUpdCodeWelknownAttrMiss	Counter32
	rcStatBgpPeerTxUpdCodeAttrFlagError	Counter32
	rcStatBgpPeerTxUpdCodeAttrLenError	Counter32
	rcStatBgpPeerTxUpdCodeBadORIGINAttr	Counter32
	rcStatBgpPeerTxUpdCodeASRoutingLoop	Counter32
	rcStatBgpPeerTxUpdCodeBadNHAttr	Counter32
	rcStatBgpPeerTxUpdCodeOptionalAttrError	Counter32
	rcStatBgpPeerTxUpdCodeBadNetworkField	Counter32
	rcStatBgpPeerTxUpdCodeMalformedASPath	Counter32
	rcStatBgpPeerReset	EnableValue

RcStatBgpPeerAfEntry
SEQUENCE
	rcStatBgpPeerAfAddrType	InetAddressType
	rcStatBgpPeerAfAddr	InetAddress
	rcStatBgpPeerAfStarts	Counter32
	rcStatBgpPeerAfStops	Counter32
	rcStatBgpPeerAfOpens	Counter32
	rcStatBgpPeerAfCloses	Counter32
	rcStatBgpPeerAfFails	Counter32
	rcStatBgpPeerAfFatals	Counter32
	rcStatBgpPeerAfConnExps	Counter32
	rcStatBgpPeerAfHoldExps	Counter32
	rcStatBgpPeerAfKeepExps	Counter32
	rcStatBgpPeerAfTxMsgs	Counter32
	rcStatBgpPeerAfTxOpens	Counter32
	rcStatBgpPeerAfTxKeeps	Counter32
	rcStatBgpPeerAfTxUpdates	Counter32
	rcStatBgpPeerAfTxNotifys	Counter32
	rcStatBgpPeerAfRxMsgs	Counter32
	rcStatBgpPeerAfRxInCompPkts	Counter32
	rcStatBgpPeerAfRxOpens	Counter32
	rcStatBgpPeerAfRxKeeps	Counter32
	rcStatBgpPeerAfRxUpdates	Counter32
	rcStatBgpPeerAfRxNotifys	Counter32
	rcStatBgpPeerAfBadEvents	Counter32
	rcStatBgpPeerAfSyncFails	Counter32
	rcStatBgpPeerAfRcvdTooShort	Counter32
	rcStatBgpPeerAfNoMarker	Counter32
	rcStatBgpPeerAfDropped	Counter32
	rcStatBgpPeerAfBadMsgTypes	Counter32
	rcStatBgpPeerAfTrEvent	Counter32
	rcStatBgpPeerAfTxRoutes	Counter32
	rcStatBgpPeerAfRxRoutesAdded	Counter32
	rcStatBgpPeerAfRxRoutesReplaced	Counter32
	rcStatBgpPeerAfRxNlri	Counter32
	rcStatBgpPeerAfRxValidUpdates	Counter32
	rcStatBgpPeerAfRxECodeHeader	Counter32
	rcStatBgpPeerAfRxECodeOpen	Counter32
	rcStatBgpPeerAfRxECodeUpdate	Counter32
	rcStatBgpPeerAfRxECodeHoldtimer	Counter32
	rcStatBgpPeerAfRxECodeFSM	Counter32
	rcStatBgpPeerAfRxECodeCease	Counter32
	rcStatBgpPeerAfRxHdrCodeNoSync	Counter32
	rcStatBgpPeerAfRxHdrCodeInvalidMsgLen	Counter32
	rcStatBgpPeerAfRxHdrCodeInvalidMsgType	Counter32
	rcStatBgpPeerAfRxOpCodeBadVer	Counter32
	rcStatBgpPeerAfRxOpCodeBadAs	Counter32
	rcStatBgpPeerAfRxOpCodeBadRtID	Counter32
	rcStatBgpPeerAfRxOpCodeUnsuppOption	Counter32
	rcStatBgpPeerAfRxOpCodeAuthFail	Counter32
	rcStatBgpPeerAfRxOpCodeBadHold	Counter32
	rcStatBgpPeerAfRxUpdCodeMalformedAttrList	Counter32
	rcStatBgpPeerAfRxUpdCodeWelknownAttrUnrecog	Counter32
	rcStatBgpPeerAfRxUpdCodeWelknownAttrMiss	Counter32
	rcStatBgpPeerAfRxUpdCodeAttrFlagError	Counter32
	rcStatBgpPeerAfRxUpdCodeAttrLenError	Counter32
	rcStatBgpPeerAfRxUpdCodeBadORIGINAttr	Counter32
	rcStatBgpPeerAfRxUpdCodeASRoutingLoop	Counter32
	rcStatBgpPeerAfRxUpdCodeBadNHAttr	Counter32
	rcStatBgpPeerAfRxUpdCodeOptionalAttrError	Counter32
	rcStatBgpPeerAfRxUpdCodeBadNetworkField	Counter32
	rcStatBgpPeerAfRxUpdCodeMalformedASPath	Counter32
	rcStatBgpPeerAfTxECodeHeader	Counter32
	rcStatBgpPeerAfTxECodeOpen	Counter32
	rcStatBgpPeerAfTxECodeUpdate	Counter32
	rcStatBgpPeerAfTxECodeHoldtimer	Counter32
	rcStatBgpPeerAfTxECodeFSM	Counter32
	rcStatBgpPeerAfTxECodeCease	Counter32
	rcStatBgpPeerAfTxHdrCodeNoSync	Counter32
	rcStatBgpPeerAfTxHdrCodeInvalidMsgLen	Counter32
	rcStatBgpPeerAfTxHdrCodeInvalidMsgType	Counter32
	rcStatBgpPeerAfTxOpCodeBadVer	Counter32
	rcStatBgpPeerAfTxOpCodeBadAs	Counter32
	rcStatBgpPeerAfTxOpCodeBadRtID	Counter32
	rcStatBgpPeerAfTxOpCodeUnsuppOption	Counter32
	rcStatBgpPeerAfTxOpCodeAuthFail	Counter32
	rcStatBgpPeerAfTxOpCodeBadHold	Counter32
	rcStatBgpPeerAfTxUpdCodeMalformedAttrList	Counter32
	rcStatBgpPeerAfTxUpdCodeWelknownAttrUnrecog	Counter32
	rcStatBgpPeerAfTxUpdCodeWelknownAttrMiss	Counter32
	rcStatBgpPeerAfTxUpdCodeAttrFlagError	Counter32
	rcStatBgpPeerAfTxUpdCodeAttrLenError	Counter32
	rcStatBgpPeerAfTxUpdCodeBadORIGINAttr	Counter32
	rcStatBgpPeerAfTxUpdCodeASRoutingLoop	Counter32
	rcStatBgpPeerAfTxUpdCodeBadNHAttr	Counter32
	rcStatBgpPeerAfTxUpdCodeOptionalAttrError	Counter32
	rcStatBgpPeerAfTxUpdCodeBadNetworkField	Counter32
	rcStatBgpPeerAfTxUpdCodeMalformedASPath	Counter32
	rcStatBgpPeerAfReset	TruthValue

RcStgEntry
SEQUENCE
	rcStgId	INTEGER
	rcStgTaggedBpduAddress	MacAddress
	rcStgTaggedBpduVlanId	Integer32
	rcStgBridgeAddress	MacAddress
	rcStgNumPorts	Integer32
	rcStgProtocolSpecification	INTEGER
	rcStgPriority	INTEGER
	rcStgTimeSinceTopologyChange	TimeTicks
	rcStgTopChanges	Counter32
	rcStgDesignatedRoot	BridgeId
	rcStgRootCost	Integer32
	rcStgRootPort	InterfaceIndex
	rcStgMaxAge	Timeout
	rcStgHelloTime	Timeout
	rcStgHoldTime	Integer32
	rcStgForwardDelay	Timeout
	rcStgBridgeMaxAge	Timeout
	rcStgBridgeHelloTime	Timeout
	rcStgBridgeForwardDelay	Timeout
	rcStgEnableStp	TruthValue
	rcStgStpTrapEnable	TruthValue
	rcStgPortMembers	OCTET STRING
	rcStgRowStatus	RowStatus
	rcStgPortStpState	OCTET STRING
	rcStgType	INTEGER
	rcStgNtStgEnable	TruthValue

RcStgPortEntry
SEQUENCE
	rcStgPort	InterfaceIndex
	rcStgPortStgId	INTEGER
	rcStgPortPriority	INTEGER
	rcStgPortState	INTEGER
	rcStgPortEnableStp	TruthValue
	rcStgPortFastStart	TruthValue
	rcStgPortPathCost	INTEGER
	rcStgPortDesignatedRoot	BridgeId
	rcStgPortDesignatedCost	Integer32
	rcStgPortDesignatedBridge	BridgeId
	rcStgPortDesignatedPort	OCTET STRING
	rcStgPortForwardTransitions	Counter32
	rcStgPortInConfigBpdus	Counter32
	rcStgPortInTcnBpdus	Counter32
	rcStgPortInBadBpdus	Counter32
	rcStgPortOutConfigBpdus	Counter32
	rcStgPortOutTcnBpdus	Counter32
	rcStgPortRowStatus	RowStatus
	rcStgPortChangeDetection	TruthValue
	rcStgPortPathCost32	Integer32

RcBridgeFdbEntry
SEQUENCE
	rcBridgeFdbStatus	INTEGER
	rcBridgeFdbAddress	MacAddress
	rcBridgeFdbPort	InterfaceIndex
	rcBridgeFdbMonitor	TruthValue
	rcBridgeFdbPriority	INTEGER
	rcBridgeFdbQosLevel	INTEGER
	rcBridgeFdbSmltRemote	TruthValue
	rcBridgeFdbVlanId	INTEGER

RcBridgeStaticEntry
SEQUENCE
	rcBridgeStaticAddress	MacAddress
	rcBridgeStaticPort	InterfaceIndex
	rcBridgeStaticMonitor	TruthValue
	rcBridgeStaticPriority	INTEGER
	rcBridgeStaticStatus	INTEGER
	rcBridgeStaticQosLevel	INTEGER
	rcBridgeStaticVlanId	INTEGER

RcBridgeFilterEntry
SEQUENCE
	rcBridgeFilterAddress	MacAddress
	rcBridgeFilterPort	InterfaceIndex
	rcBridgeFilterNotAllowedFrom	OCTET STRING
	rcBridgeFilterStatus	INTEGER
	rcBridgeFilterVlanId	INTEGER
	rcBridgeFilterPcap	TruthValue
	rcBridgeFilterDestDiscard	OCTET STRING
	rcBridgeFilterSrcDiscard	OCTET STRING

RcBridgeUnknownMacDiscardEntry
SEQUENCE
	rcBridgeUnknownMacDiscardIfIndex	InterfaceIndex
	rcBridgeUnknownMacDiscardAutoLearnEnable	TruthValue
	rcBridgeUnknownMacDiscardAutoLearnMode	INTEGER
	rcBridgeUnknownMacDiscardAutoLearnTableMode	INTEGER
	rcBridgeUnknownMacDiscardLogViolations	INTEGER
	rcBridgeUnknownMacDiscardSendTrap	INTEGER
	rcBridgeUnknownMacDiscardDisablePort	INTEGER
	rcBridgeUnknownMacDiscardDefaultAutoLearnMonitor	INTEGER
	rcBridgeUnknownMacDiscardDefaultAutoLearnPriority	INTEGER
	rcBridgeUnknownMacDiscardMacCountMax	INTEGER
	rcBridgeUnknownMacDiscardMacCountCur	INTEGER

RcBridgeManualEditEntry
SEQUENCE
	rcBridgeManualEditAddress	MacAddress
	rcBridgeManualEditPorts	PortSet
	rcBridgeManualEditMonitor	TruthValue
	rcBridgeManualEditPriority	INTEGER
	rcBridgeManualEditStatus	INTEGER

RcBridgeAutoLearnEntry
SEQUENCE
	rcBridgeAutoLearnAddress	MacAddress
	rcBridgeAutoLearnPort	PortSet
	rcBridgeAutoLearnMonitor	TruthValue
	rcBridgeAutoLearnPriority	INTEGER
	rcBridgeAutoLearnAction	INTEGER

RcBridgeStaticMulticastEntry
SEQUENCE
	rcBridgeStaticMulticastAddress	MacAddress
	rcBridgeStaticMulticastForwardingPorts	PortSet
	rcBridgeStaticMulticastMltIds	IdList
	rcBridgeStaticMulticastRowStatus	RowStatus
	rcBridgeStaticMulticastVlanId	INTEGER
	rcBridgeStaticMulticastNumMltIds	Integer32

RcRateLimitEntry
SEQUENCE
	rcRateLimitIfIndex	InterfaceIndex
	rcRateLimitIfTrafficType	INTEGER
	rcRateLimitIfAllowedRate	INTEGER
	rcRateLimitIfEnable	TruthValue
	rcRateLimitIfAllowedRatePps	Integer32
	rcRateLimitIfAllowedRateKbps	INTEGER

RcBridgeStaticMcastEntry
SEQUENCE
	rcBridgeStaticMcastVlanId	INTEGER
	rcBridgeStaticMcastAddress	MacAddress
	rcBridgeStaticMcastForwardingPorts	PortSet
	rcBridgeStaticMcastMltIds	IdList
	rcBridgeStaticMcastNumMltIds	Integer32
	rcBridgeStaticMcastRowStatus	RowStatus

RcBridgeFdbProtectEntry
SEQUENCE
	rcBridgeFdbProtectPortNum	InterfaceIndex
	rcBridgeFdbProtectMaxMacCount	Integer32
	rcBridgeFdbProtectMinMacCount	Integer32
	rcBridgeFdbProtectEnable	EnableValue
	rcBridgeFdbProtectCurrentMacCount	Integer32
	rcBridgeFdbProtectMacLearning	TruthValue
	rcBridgeFdbProtectViolationLogTrap	EnableValue
	rcBridgeFdbProtectViolationDownPort	EnableValue

RcBridgeNewFdbEntry
SEQUENCE
	rcBridgeNewFdbStatus	INTEGER
	rcBridgeNewFdbAddress	MacAddress
	rcBridgeNewFdbPort	InterfaceIndex
	rcBridgeNewFdbMonitor	TruthValue
	rcBridgeNewFdbQosLevel	INTEGER
	rcBridgeNewFdbSmltRemote	TruthValue
	rcBridgeNewFdbVlanId	INTEGER

RcBridgeRemoteMacEntry
SEQUENCE
	rcBridgeRemoteMacVlanId	Integer32
	rcBridgeRemoteMacAddr	MacAddress
	rcBridgeRemoteMacStatus	INTEGER
	rcBridgeRemoteMacDestAddr	MacAddress
	rcBridgeRemoteMacPrimaryBVlanId	Integer32
	rcBridgeRemoteMacPrimaryDestSysName	OCTET STRING
	rcBridgeRemoteMacPrimaryPort	InterfaceIndex
	rcBridgeRemoteMacSecondaryBVlanId	Integer32
	rcBridgeRemoteMacSecondaryDestSysName	OCTET STRING
	rcBridgeRemoteMacSecondaryPort	InterfaceIndex
	rcBridgeRemoteMacSmltRemote	TruthValue

RcDeviceFlashEntry
SEQUENCE
	rcDeviceFlashFileNum	INTEGER
	rcDeviceFlashFileName	DisplayString
	rcDeviceFlashFileVersion	DisplayString
	rcDeviceFlashFileType	INTEGER
	rcDeviceFlashFileMode	INTEGER
	rcDeviceFlashFileSize	Integer32
	rcDeviceFlashFileCrc	Integer32
	rcDeviceFlashFileStatus	INTEGER
	rcDeviceFlashRowStatus	RowStatus

RcDevicePcmciaEntry
SEQUENCE
	rcDevicePcmciaFileNum	INTEGER
	rcDevicePcmciaFileName	DisplayString
	rcDevicePcmciaFileVersion	DisplayString
	rcDevicePcmciaFileType	INTEGER
	rcDevicePcmciaFileMode	INTEGER
	rcDevicePcmciaFileSize	Integer32
	rcDevicePcmciaFileCrc	Integer32
	rcDevicePcmciaFileStatus	INTEGER
	rcDevicePcmciaRowStatus	RowStatus

RcMltEntry
SEQUENCE
	rcMltId	INTEGER
	rcMltName	DisplayString
	rcMltPortMembers	PortSet
	rcMltPortType	INTEGER
	rcMltNumVlanIds	Integer32
	rcMltVlanIds	IdList
	rcMltRowStatus	RowStatus
	rcMltEnable	TruthValue
	rcMltLoadBalance	TruthValue
	rcMltDistributionAlgorithm	INTEGER
	rcMltIfIndex	InterfaceIndex
	rcMltMltType	INTEGER
	rcMltSmltId	INTEGER
	rcMltRunningType	INTEGER
	rcMltSvlanPortType	INTEGER
	rcMltMulticastDistribution	EnableValue
	rcMltAggregatable	EnableValue
	rcMltClearLinkAggregate	INTEGER
	rcMltNtStgEnable	TruthValue
	rcMltDesignatedPort	InterfaceIndex
	rcMltAggOperState	EnableValue
	rcMltAggTimeOfLastOperChange	TimeTicks
	rcMltAggMinLink	Integer32
	rcMltVlanIdList	OCTET STRING

RcSltPortEntry
SEQUENCE
	rcSltPortIfIndex	InterfaceIndex
	rcSltPortSmltId	INTEGER
	rcSltPortOperType	INTEGER
	rcSltPortRowStatus	RowStatus

IpAddressOriginTC
The origin of the address. manual(2) indicates that the address was manually configured to a specified address, e.g. by user configuration. dhcp(4) indicates an address that was assigned to this system by a DHCP server. linklayer(5) indicates an address created by IPv6 stateless auto-configuration. random(6) indicates an address chosen by the system at random, e.g. an IPv4 address within 169.254/16, or an RFC 3041 privacy address.
TEXTUAL-CONVENTION
	INTEGER	other(1), manual(2), dhcp(4), linklayer(5), random(6)

IpAddressStatusTC
The status of an address. Most of the states correspond to states from the IPv6 Stateless Address Autoconfiguration protocol [5]. The preferred(1) state indicates that this is a valid address that can appear as the destination or source address of a packet. The deprecated(2) state indicates that this is a valid but deprecated address that should no longer be used as a source address in new communications, but packets addressed to such an address are processed as expected. The invalid(3) state indicates that this isn't a valid address and it shouldn't appear as the destination or source address of a packet. The inaccessible(4) state indicates that the address is not accessible because the interface to which this address is assigned is not operational. The unknown(5) state indicates that the status can not be determined for some reason. The tentative(6) state indicates the uniqueness of the address on the link is being verified. Addresses in this state should not be used for general communication and should only be used to determine the uniqueness of the address. The duplicate(7) state indicates the address has been determined to be non-unique on the link and so must not be used. In the absence of other information, an IPv4 address is always preferred(1).
TEXTUAL-CONVENTION
	INTEGER	preferred(1), deprecated(2), invalid(3), inaccessible(4), unknown(5), tentative(6), duplicate(7)

RcIpv6InterfaceEntry
SEQUENCE
	rcIpv6InterfaceIfIndex	InterfaceIndex
	rcIpv6InterfaceIdentifier	Ipv6AddressIfIdentifier
	rcIpv6InterfaceIdentifierLength	INTEGER
	rcIpv6InterfaceDescr	DisplayString
	rcIpv6InterfaceVlanId	INTEGER
	rcIpv6InterfaceType	INTEGER
	rcIpv6InterfaceReasmMaxSize	INTEGER
	rcIpv6InterfacePhysAddress	PhysAddress
	rcIpv6InterfaceAdminStatus	TruthValue
	rcIpv6InterfaceOperStatus	INTEGER
	rcIpv6InterfaceReachableTime	INTEGER
	rcIpv6InterfaceRetransmitTime	INTEGER
	rcIpv6InterfaceMulticastAdminStatus	TruthValue
	rcIpv6InterfaceRowStatus	RowStatus
	rcIpv6InterfaceDhcpEnabled	TruthValue
	rcIpv6InterfaceMacOffset	Integer32

RcIpv6AddressEntry
SEQUENCE
	rcIpv6AddressIfIndex	InterfaceIndex
	rcIpv6AddressAddr	Ipv6Address
	rcIpv6AddressType	INTEGER
	rcIpv6AddressPrefixLength	INTEGER
	rcIpv6AddressPrefix	RowPointer
	rcIpv6AddressOrigin	IpAddressOriginTC
	rcIpv6AddressStatus	IpAddressStatusTC
	rcIpv6AddressCreated	TimeStamp
	rcIpv6AddressLastChanged	TimeStamp
	rcIpv6AddressRowStatus	RowStatus

RcIpv6PrefixEntry
SEQUENCE
	rcIpv6PrefixIfIndex	InterfaceIndex
	rcIpv6PrefixAddr	Ipv6Address
	rcIpv6PrefixLength	INTEGER
	rcIpv6PrefixVlanId	INTEGER
	rcIpv6PrefixUseDefaultVal	INTEGER
	rcIpv6PrefixValidLife	Integer32
	rcIpv6PrefixPreferredLife	Integer32
	rcIpv6PrefixAtValidLife	DateAndTime
	rcIpv6PrefixAtPreferredLife	DateAndTime
	rcIpv6PrefixInfinite	TruthValue
	rcIpv6PrefixOnLinkFlag	TruthValue
	rcIpv6PrefixAutoFlag	TruthValue
	rcIpv6PrefixAddressEui	INTEGER
	rcIpv6PrefixNoAdvertise	TruthValue
	rcIpv6PrefixRowStatus	RowStatus
	rcIpv6PrefixValidLifetime	Unsigned32
	rcIpv6PrefixPreferredLifetime	Unsigned32

RcIpv6RouterAdvertEntry
SEQUENCE
	rcIpv6RouterAdvertIfIndex	InterfaceIndex
	rcIpv6RouterAdvertSendAdverts	TruthValue
	rcIpv6RouterAdvertUseDefaultVal	INTEGER
	rcIpv6RouterAdvertMaxInterval	INTEGER
	rcIpv6RouterAdvertMinInterval	INTEGER
	rcIpv6RouterAdvertReachableTime	INTEGER
	rcIpv6RouterAdvertRetransmitTimer	INTEGER
	rcIpv6RouterAdvertDefaultLifeTime	INTEGER
	rcIpv6RouterAdvertCurHopLimit	INTEGER
	rcIpv6RouterAdvertManagedFlag	TruthValue
	rcIpv6RouterAdvertOtherConfigFlag	TruthValue
	rcIpv6RouterAdvertDadNsNum	INTEGER
	rcIpv6RouterAdvertLinkMTU	Unsigned32

RcIpv6StaticRouteEntry
SEQUENCE
	rcIpv6StaticRouteDest	Ipv6Address
	rcIpv6StaticRoutePrefixLength	INTEGER
	rcIpv6StaticRouteNextHop	Ipv6Address
	rcIpv6StaticRouteIfIndex	InterfaceIndex
	rcIpv6StaticRouteDistance	INTEGER
	rcIpv6StaticRouteEnable	TruthValue
	rcIpv6StaticRouteStatus	INTEGER
	rcIpv6StaticRoutePreference	INTEGER
	rcIpv6StaticRouteRowStatus	RowStatus

RcIpv6NetToPhysicalEntry
SEQUENCE
	rcIpv6NetToPhysicalIfIndex	InterfaceIndex
	rcIpv6NetToPhysicalNetAddress	Ipv6Address
	rcIpv6NetToPhysicalPhysAddress	PhysAddress
	rcIpv6NetToPhysicalInterface	Integer32
	rcIpv6NetToPhysicalLastUpdated	TimeStamp
	rcIpv6NetToPhysicalType	INTEGER
	rcIpv6NetToPhysicalState	INTEGER
	rcIpv6NetToPhysicalRowStatus	RowStatus

RcIpv6PrefixListEntry
SEQUENCE
	rcIpv6PrefixListId	Unsigned32
	rcIpv6PrefixListPrefix	Ipv6Address
	rcIpv6PrefixListPrefixMaskLen	Unsigned32
	rcIpv6PrefixListMaskLenFrom	Unsigned32
	rcIpv6PrefixListMaskLenUpto	Unsigned32
	rcIpv6PrefixListName	SnmpAdminString
	rcIpv6PrefixListRowStatus	RowStatus

UpToRefreshInterval
The values one might be able to configure for variables bounded by the Refresh Interval
TEXTUAL-CONVENTION
	Integer32	1..1800

RouterDeadRange
The range of intervals in seconds that a routers hello must have not been seen before a neighbor declares the router down
TEXTUAL-CONVENTION
	Integer32	1..FFF

RcOspfv3AreaEntry
SEQUENCE
	rcOspfv3AreaId	IpAddress
	rcOspfv3ImportAsExtern	INTEGER
	rcOspfv3AreaSpfRuns	Counter32
	rcOspfv3AreaBdrRtrCount	Gauge32
	rcOspfv3AreaAsBdrRtrCount	Gauge32
	rcOspfv3AreaScopeLsaCount	Gauge32
	rcOspfv3AreaScopeLsaCksumSum	Integer32
	rcOspfv3AreaSummary	INTEGER
	rcOspfv3AreaStatus	RowStatus
	rcOspfv3StubMetric	Integer32
	rcOspfv3AreaNssaTranslatorRole	INTEGER
	rcOspfv3AreaNssaTranslatorState	INTEGER
	rcOspfv3AreaNssaTranslatorStabilityInterval	Unsigned32
	rcOspfv3AreaNssaTranslatorEvents	Counter32
	rcOspfv3AreaStubMetricType	INTEGER

RcOspfv3AsLsdbEntry
SEQUENCE
	rcOspfv3AsLsdbType	INTEGER
	rcOspfv3AsLsdbRouterId	IpAddress
	rcOspfv3AsLsdbLsid	Unsigned32
	rcOspfv3AsLsdbSequence	Integer32
	rcOspfv3AsLsdbAge	Integer32
	rcOspfv3AsLsdbChecksum	Integer32
	rcOspfv3AsLsdbAdvertisement	OCTET STRING
	rcOspfv3AsLsdbTypeKnown	TruthValue

RcOspfv3AreaLsdbEntry
SEQUENCE
	rcOspfv3AreaLsdbAreaId	IpAddress
	rcOspfv3AreaLsdbType	INTEGER
	rcOspfv3AreaLsdbRouterId	IpAddress
	rcOspfv3AreaLsdbLsid	Unsigned32
	rcOspfv3AreaLsdbSequence	Integer32
	rcOspfv3AreaLsdbAge	Integer32
	rcOspfv3AreaLsdbChecksum	Integer32
	rcOspfv3AreaLsdbAdvertisement	OCTET STRING
	rcOspfv3AreaLsdbTypeKnown	TruthValue

RcOspfv3LinkLsdbEntry
SEQUENCE
	rcOspfv3LinkLsdbIfIndex	InterfaceIndex
	rcOspfv3LinkLsdbType	INTEGER
	rcOspfv3LinkLsdbRouterId	IpAddress
	rcOspfv3LinkLsdbLsid	Unsigned32
	rcOspfv3LinkLsdbSequence	Integer32
	rcOspfv3LinkLsdbAge	Integer32
	rcOspfv3LinkLsdbChecksum	Integer32
	rcOspfv3LinkLsdbAdvertisement	OCTET STRING
	rcOspfv3LinkLsdbTypeKnown	TruthValue

RcOspfv3HostEntry
SEQUENCE
	rcOspfv3HostAddressType	INTEGER
	rcOspfv3HostAddress	OCTET STRING
	rcOspfv3HostMetric	Integer32
	rcOspfv3HostStatus	RowStatus
	rcOspfv3HostAreaID	IpAddress

RcOspfv3IfEntry
SEQUENCE
	rcOspfv3IfIndex	InterfaceIndex
	rcOspfv3IfAreaId	IpAddress
	rcOspfv3IfType	INTEGER
	rcOspfv3IfAdminStat	INTEGER
	rcOspfv3IfRtrPriority	Integer32
	rcOspfv3IfTransitDelay	Integer32
	rcOspfv3IfRetransInterval	Integer32
	rcOspfv3IfHelloInterval	Integer32
	rcOspfv3IfRtrDeadInterval	Integer32
	rcOspfv3IfPollInterval	Unsigned32
	rcOspfv3IfState	INTEGER
	rcOspfv3IfDesignatedRouter	IpAddress
	rcOspfv3IfBackupDesignatedRouter	IpAddress
	rcOspfv3IfEvents	Counter32
	rcOspfv3IfStatus	RowStatus
	rcOspfv3IfMulticastForwarding	INTEGER
	rcOspfv3IfDemand	TruthValue
	rcOspfv3IfMetricValue	Integer32
	rcOspfv3IfLinkScopeLsaCount	Gauge32
	rcOspfv3IfLinkLsaCksumSum	Integer32
	rcOspfv3IfInstId	Integer32
	rcOspfv3IfDemandNbrProbe	TruthValue
	rcOspfv3IfDemandNbrProbeRetxLimit	Unsigned32
	rcOspfv3IfDemandNbrProbeInterval	Unsigned32

RcOspfv3VirtIfEntry
SEQUENCE
	rcOspfv3VirtIfAreaId	IpAddress
	rcOspfv3VirtIfNeighbor	IpAddress
	rcOspfv3VirtIfIndex	Integer32
	rcOspfv3VirtIfTransitDelay	Integer32
	rcOspfv3VirtIfRetransInterval	Integer32
	rcOspfv3VirtIfHelloInterval	Integer32
	rcOspfv3VirtIfRtrDeadInterval	Integer32
	rcOspfv3VirtIfState	INTEGER
	rcOspfv3VirtIfEvents	Counter32
	rcOspfv3VirtIfStatus	RowStatus
	rcOspfv3VirtIfLinkScopeLsaCount	Gauge32
	rcOspfv3VirtIfLinkLsaCksumSum	Integer32

RcOspfv3NbrEntry
SEQUENCE
	rcOspfv3NbrIfIndex	InterfaceIndex
	rcOspfv3NbrRtrId	IpAddress
	rcOspfv3NbrAddressType	INTEGER
	rcOspfv3NbrAddress	OCTET STRING
	rcOspfv3NbrOptions	Integer32
	rcOspfv3NbrPriority	INTEGER
	rcOspfv3NbrState	INTEGER
	rcOspfv3NbrEvents	Counter32
	rcOspfv3NbrLsRetransQLen	Gauge32
	rcOspfv3NbrHelloSuppressed	TruthValue
	rcOspfv3NbrIfId	Integer32
	rcOspfv3NbrRestartHelperStatus	INTEGER
	rcOspfv3NbrRestartHelperAge	Integer32
	rcOspfv3NbrRestartHelperExitReason	INTEGER

RcOspfv3NbmaNbrEntry
SEQUENCE
	rcOspfv3NbmaNbrIfIndex	InterfaceIndex
	rcOspfv3NbmaNbrAddress	Ipv6Address
	rcOspfv3NbmaNbrPriority	INTEGER
	rcOspfv3NbmaNbrRtrId	IpAddress
	rcOspfv3NbmaNbrState	INTEGER
	rcOspfv3NbmaNbrStorageType	StorageType
	rcOspfv3NbmaNbrStatus	RowStatus

RcOspfv3VirtNbrEntry
SEQUENCE
	rcOspfv3VirtNbrArea	IpAddress
	rcOspfv3VirtNbrRtrId	IpAddress
	rcOspfv3VirtNbrIfIndex	Integer32
	rcOspfv3VirtNbrAddressType	INTEGER
	rcOspfv3VirtNbrAddress	OCTET STRING
	rcOspfv3VirtNbrOptions	Integer32
	rcOspfv3VirtNbrState	INTEGER
	rcOspfv3VirtNbrEvents	Counter32
	rcOspfv3VirtNbrLsRetransQLen	Gauge32
	rcOspfv3VirtNbrHelloSuppressed	TruthValue
	rcOspfv3VirtNbrIfId	Integer32
	rcOspfv3VirtNbrRestartHelperStatus	INTEGER
	rcOspfv3VirtNbrRestartHelperAge	Integer32
	rcOspfv3VirtNbrRestartHelperExitReason	INTEGER

RcOspfv3AreaAggregateEntry
SEQUENCE
	rcOspfv3AreaAggregateAreaID	IpAddress
	rcOspfv3AreaAggregateAreaLsdbType	INTEGER
	rcOspfv3AreaAggregatePrefix	Ipv6Address
	rcOspfv3AreaAggregatePrefixLength	Unsigned32
	rcOspfv3AreaAggregateStatus	RowStatus
	rcOspfv3AreaAggregateEffect	INTEGER
	rcOspfv3AreaAggregateRouteTag	Integer32
	rcOspfv3AreaAggregateAdvertiseMetric	INTEGER

RcIpv6ConfDhcpRelayEntry
SEQUENCE
	rcIpv6ConfDhcpIfIndex	InterfaceIndex
	rcIpv6ConfDhcpMaxHop	Unsigned32
	rcIpv6ConfDhcpRemoteIdEnabled	TruthValue
	rcIpv6ConfDhcpNumRequests	Counter32
	rcIpv6ConfDhcpNumReplies	Counter32
	rcIpv6ConfDhcpRowStatus	RowStatus

RcIpv6DhcpForwardEntry
SEQUENCE
	rcIpv6DhcpForwardAgentAddr	Ipv6Address
	rcIpv6DhcpForwardServerAddr	Ipv6Address
	rcIpv6DhcpForwardEnabled	TruthValue
	rcIpv6DhcpForwardRowStatus	RowStatus

RcIpv6RadiusServEntry
SEQUENCE
	rcIpv6RadiusServAddress	Ipv6Address
	rcIpv6RadiusServUsedBy	INTEGER
	rcIpv6RadiusServPriority	Unsigned32
	rcIpv6RadiusServTimeOut	Unsigned32
	rcIpv6RadiusServEnable	TruthValue
	rcIpv6RadiusServMaxRetries	Unsigned32
	rcIpv6RadiusServUdpPort	Unsigned32
	rcIpv6RadiusServSecretKey	SnmpAdminString
	rcIpv6RadiusServAccessRequests	Counter32
	rcIpv6RadiusServAccessAccepts	Counter32
	rcIpv6RadiusServAccessRejects	Counter32
	rcIpv6RadiusServBadResponses	Counter32
	rcIpv6RadiusServPendingRequests	Counter32
	rcIpv6RadiusServClientRetries	Counter32
	rcIpv6RadiusServAcctEnable	TruthValue
	rcIpv6RadiusServAcctUdpPort	Unsigned32
	rcIpv6RadiusServAcctOnRequests	Counter32
	rcIpv6RadiusServAcctOffRequests	Counter32
	rcIpv6RadiusServAcctStartRequests	Counter32
	rcIpv6RadiusServAcctStopRequests	Counter32
	rcIpv6RadiusServAcctInterimRequests	Counter32
	rcIpv6RadiusServAcctBadResponses	Counter32
	rcIpv6RadiusServAcctPendingRequests	Counter32
	rcIpv6RadiusServAcctClientRetries	Counter32
	rcIpv6RadiusServNasIpAddress	Ipv6Address
	rcIpv6RadiusServRoundTripTime	SnmpAdminString
	rcIpv6RadiusServAccessChallanges	Counter32
	rcIpv6RadiusServSourceIpAddr	Ipv6Address
	rcIpv6RadiusServRowStatus	RowStatus

RcIpMRouteStatsEntry
SEQUENCE
	rcIpMRouteStatsGroupAddress	IpAddress
	rcIpMRouteStatsSourceCount	Counter32
	rcIpMRouteStatsPkts	Counter64
	rcIpMRouteStatsBytes	Counter64
	rcIpMRouteStatsAverageSizePerPkt	Integer32
	rcIpMRouteStatsDropPkts	Counter64
	rcIpMRouteStatsDropBytes	Counter64
	rcIpMRouteStatsPktsPerSecond	Integer32

RcSyslogHostEntry
SEQUENCE
	rcSyslogHostId	INTEGER
	rcSyslogHostIpAddr	IpAddress
	rcSyslogHostUdpPort	INTEGER
	rcSyslogHostFacility	INTEGER
	rcSyslogHostModuleId	INTEGER
	rcSyslogHostModuleId2	Integer32
	rcSyslogHostSeverity	INTEGER
	rcSyslogHostMapInfoSeverity	INTEGER
	rcSyslogHostMapWarningSeverity	INTEGER
	rcSyslogHostMapErrorSeverity	INTEGER
	rcSyslogHostMapMfgSeverity	INTEGER
	rcSyslogHostMapFatalSeverity	INTEGER
	rcSyslogHostMapTraceMsg	INTEGER
	rcSyslogHostMapTrapMsg	INTEGER
	rcSyslogHostLogTraceMsgs	TruthValue
	rcSyslogHostLogTrapMsgs	TruthValue
	rcSyslogHostEnable	TruthValue
	rcSyslogHostRowStatus	RowStatus

RcDiagMirrorByPortEntry
SEQUENCE
	rcDiagMirrorByPortId	INTEGER
	rcDiagMirrorByPortMirroredPort	InterfaceIndex
	rcDiagMirrorByPortMirroringPort	InterfaceIndex
	rcDiagMirrorByPortMode	INTEGER
	rcDiagMirrorByPortEnable	TruthValue
	rcDiagMirrorByPortRowStatus	RowStatus
	rcDiagMirrorByPortOctapidId	Integer32
	rcDiagMirrorByPortPid	Integer32
	rcDiagMirrorRemoteMirrorVlanId	INTEGER
	rcDiagMirrorByPortMirroredPortList	PortSet
	rcDiagMirrorByPortMirroringPortList	PortSet
	rcDiagMirrorMirroringVlanId	Integer32
	rcDiagMirrorMirroringMltId	Integer32
	rcDiagMirrorMirroringMgId	Integer32

RcDiagPortConvSteeringEntry
SEQUENCE
	rcDiagPortConvSteeringId	Integer32
	rcDiagPortConvSteeringPortOne	Integer32
	rcDiagPortConvSteeringPortTwo	Integer32
	rcDiagPortConvSteeringMode	INTEGER
	rcDiagPortConvSteeringForwardPort	Integer32
	rcDiagPortConvSteeringEnable	TruthValue
	rcDiagPortConvSteeringRowStatus	RowStatus

RcDiagMacConvSteeringEntry
SEQUENCE
	rcDiagMacConvSteeringId	Integer32
	rcDiagMacConvSteeringSrcMac	MacAddress
	rcDiagMacConvSteeringDstMac	MacAddress
	rcDiagMacConvSteeringInPort	Integer32
	rcDiagMacConvSteeringForwardPort	Integer32
	rcDiagMacConvSteeringEnable	TruthValue
	rcDiagMacConvSteeringRowStatus	RowStatus

RcDiagPcapFilterEntry
SEQUENCE
	rcDiagPcapFilterId	INTEGER
	rcDiagPcapFilterEnable	EnableValue
	rcDiagPcapFilterAction	INTEGER
	rcDiagPcapFilterSrcMac	MacAddress
	rcDiagPcapFilterSrcMask	INTEGER	1..6
	rcDiagPcapFilterIsInverseSrcMac	TruthValue
	rcDiagPcapFilterDstMac	MacAddress
	rcDiagPcapFilterDstMask	INTEGER	1..6
	rcDiagPcapFilterIsInverseDstMac	TruthValue
	rcDiagPcapFilterVlanId	INTEGER
	rcDiagPcapFilterToVlanId	INTEGER
	rcDiagPcapFilterIsInverseVlanId	TruthValue
	rcDiagPcapFilterPbit	INTEGER
	rcDiagPcapFilterToPbit	INTEGER
	rcDiagPcapFilterIsInversePbit	TruthValue
	rcDiagPcapFilterEtherType	INTEGER
	rcDiagPcapFilterToEtherType	INTEGER
	rcDiagPcapFilterIsInverseEtherType	TruthValue
	rcDiagPcapFilterProtocolType	INTEGER
	rcDiagPcapFilterToProtocolType	INTEGER
	rcDiagPcapFilterIsInverseProtocolType	TruthValue
	rcDiagPcapFilterSrcIp	IpAddress
	rcDiagPcapFilterToSrcIp	IpAddress
	rcDiagPcapFilterIsInverseSrcIp	TruthValue
	rcDiagPcapFilterDstIp	IpAddress
	rcDiagPcapFilterToDstIp	IpAddress
	rcDiagPcapFilterIsInverseDstIp	TruthValue
	rcDiagPcapFilterDscp	INTEGER
	rcDiagPcapFilterToDscp	INTEGER
	rcDiagPcapFilterIsInverseDscp	TruthValue
	rcDiagPcapFilterRowStatus	RowStatus
	rcDiagPcapFilterDscpMatchZero	TruthValue
	rcDiagPcapFilterPbitMatchZero	TruthValue

RcDiagPcapAdvancedFilterEntry
SEQUENCE
	rcDiagPcapAdvancedFilterId	INTEGER
	rcDiagPcapAdvancedFilterUdpPort	INTEGER
	rcDiagPcapAdvancedFilterToUdpPort	INTEGER
	rcDiagPcapAdvancedFilterIsInverseUdpPort	TruthValue
	rcDiagPcapAdvancedFilterTcpPort	INTEGER
	rcDiagPcapAdvancedFilterToTcpPort	INTEGER
	rcDiagPcapAdvancedFilterIsInverseTcpPort	TruthValue
	rcDiagPcapAdvancedFilterUserDefinedData	DisplayString
	rcDiagPcapAdvancedFilterUserDefinedDataSize	INTEGER
	rcDiagPcapAdvancedFilterUserDefinedOffset	INTEGER
	rcDiagPcapAdvancedFilterIsInverseUserDefined	TruthValue
	rcDiagPcapAdvancedFilterTimer	INTEGER
	rcDiagPcapAdvancedFilterPacketCount	INTEGER
	rcDiagPcapAdvancedFilterRefreshTimer	INTEGER
	rcDiagPcapAdvancedFilterRowStatus	RowStatus

RcIpxAddrEntry
SEQUENCE
	rcIpxAddrVlanId	INTEGER
	rcIpxAddrNetAddr	OCTET STRING	Size(4)
	rcIpxAddrEncap	INTEGER
	rcIpxAddrEntryStatus	RowStatus
	rcIpxAddrTicks	INTEGER

RcIpxPolicyNetEntry
SEQUENCE
	rcIpxPolicyNetId	Integer32
	rcIpxPolicyNetFromNet	OCTET STRING	Size(4)
	rcIpxPolicyNetToNet	OCTET STRING	Size(4)
	rcIpxPolicyNetName	DisplayString
	rcIpxPolicyNetRowStatus	RowStatus

RcIpxPolicyServEntry
SEQUENCE
	rcIpxPolicyServId	Integer32
	rcIpxPolicyServServiceType	INTEGER
	rcIpxPolicyServServiceName	DisplayString
	rcIpxPolicyServName	DisplayString
	rcIpxPolicyServRowStatus	RowStatus

RcIpxPolicyListEntry
SEQUENCE
	rcIpxPolicyListId	INTEGER
	rcIpxPolicyListSeqnum	INTEGER
	rcIpxPolicyListName	DisplayString
	rcIpxPolicyListEnable	TruthValue
	rcIpxPolicyListAction	INTEGER
	rcIpxPolicyListRouteSource	INTEGER
	rcIpxPolicyListMatchNetList	DisplayString
	rcIpxPolicyListMatchServList	DisplayString
	rcIpxPolicyListHops	INTEGER
	rcIpxPolicyListTicks	INTEGER
	rcIpxPolicyListRowStatus	RowStatus

RcIpxRipOutFilterEntry
SEQUENCE
	rcIpxRipOutFilterInterface	OCTET STRING	Size(4)
	rcIpxRipOutFilterPolicyName	DisplayString
	rcIpxRipOutFilterRowStatus	RowStatus

RcIpxSapOutFilterEntry
SEQUENCE
	rcIpxSapOutFilterInterface	OCTET STRING	Size(4)
	rcIpxSapOutFilterPolicyName	DisplayString
	rcIpxSapOutFilterRowStatus	RowStatus

RcIpxRipInFilterEntry
SEQUENCE
	rcIpxRipInFilterInterface	OCTET STRING	Size(4)
	rcIpxRipInFilterPolicyName	DisplayString
	rcIpxRipInFilterRowStatus	RowStatus

RcIpxSapInFilterEntry
SEQUENCE
	rcIpxSapInFilterInterface	OCTET STRING	Size(4)
	rcIpxSapInFilterPolicyName	DisplayString
	rcIpxSapInFilterRowStatus	RowStatus

RcIpxSapInterfaceEntry
SEQUENCE
	rcIpxSapInterfaceNetNum	OCTET STRING	Size(4)
	rcIpxSapInterfaceInPolicy	DisplayString
	rcIpxSapInterfaceOutPolicy	DisplayString

RcIpxRipInterfaceEntry
SEQUENCE
	rcIpxRipInterfaceNetNum	OCTET STRING	Size(4)
	rcIpxRipInterfaceInPolicy	DisplayString
	rcIpxRipInterfaceOutPolicy	DisplayString

RcIpxBrouterEntry
SEQUENCE
	rcIpxBrouterPortIndex	Integer32
	rcIpxBrouterVlanId	INTEGER
	rcIpxBrouterNetAddr	OCTET STRING	Size(4)
	rcIpxBrouterEncap	INTEGER
	rcIpxBrouterMacOffset	INTEGER
	rcIpxBrouterTicks	INTEGER
	rcIpxBrouterRowStatus	RowStatus

RcIpxRsmltOperEntry
SEQUENCE
	rcIpxRsmltOperVlanId	INTEGER
	rcIpxRsmltOperIfIndex	InterfaceIndex
	rcIpxRsmltOperAdminStatus	TruthValue
	rcIpxRsmltOperHoldDownTimer	INTEGER
	rcIpxRsmltOperHoldDownTimeRemaining	INTEGER
	rcIpxRsmltOperHoldUpTimer	INTEGER
	rcIpxRsmltOperHoldUpTimeRemaining	INTEGER
	rcIpxRsmltOperOperStatus	INTEGER
	rcIpxRsmltOperSmltId	IdList
	rcIpxRsmltOperSltId	IdList
	rcIpxRsmltOperMacAddr	MacAddress
	rcIpxRsmltOperRowStatus	RowStatus

RcIpxRsmltPeerEntry
SEQUENCE
	rcIpxRsmltPeerVlanId	INTEGER
	rcIpxRsmltPeerIfIndex	InterfaceIndex
	rcIpxRsmltPeerAdminStatus	TruthValue
	rcIpxRsmltPeerHoldDownTimer	INTEGER
	rcIpxRsmltPeerHoldDownTimeRemaining	INTEGER
	rcIpxRsmltPeerHoldUpTimer	INTEGER
	rcIpxRsmltPeerHoldUpTimeRemaining	INTEGER
	rcIpxRsmltPeerOperStatus	INTEGER
	rcIpxRsmltPeerSmltId	IdList
	rcIpxRsmltPeerSltId	IdList
	rcIpxRsmltPeerMacAddr	MacAddress

RcPosPppIpxEntry
SEQUENCE
	rcPosPppIpxIfIndex	InterfaceIndex
	rcPosPppIpxIpxcpAdminStatus	INTEGER
	rcPosPppIpxOperStatus	INTEGER
	rcPosPppIpxNetAddr	OCTET STRING	Size(4)
	rcPosPppIpxRoutingProtocol	INTEGER

RcPosSonetEntry
SEQUENCE
	rcPosSonetIndex	InterfaceIndex
	rcPosSonetFraming	INTEGER
	rcPosSonetSectionTrace	INTEGER
	rcPosSonetSectionGrowth	INTEGER
	rcPosSonetSyncronization	INTEGER
	rcPosSonetStsPathTrace	OCTET STRING	Size(64)
	rcPosSonetPathSignalLabel	INTEGER
	rcPosSonetClockSource	INTEGER
	rcPosSonetScramble	EnableValue
	rcPosSonetOperStatusFraming	Integer32
	rcPosSonetOperStatusClockSource	Integer32
	rcPosSonetOperStatusScramble	EnableValue
	rcPosSonetOperStatusSectionTrace	Integer32
	rcPosSonetOperStatusPathSignalLabel	Integer32

RcPosLineStatusEntry
SEQUENCE
	rcPosLineStatusIndex	InterfaceIndex
	rcPosLineStatusLocalMACAddress	MacAddress
	rcPosLineStatusRemoteMACAddress	MacAddress
	rcPosLineStatusLocalIpAddr	IpAddress
	rcPosLineStatusRemoteIpAddr	IpAddress
	rcPosLineStatusOutQuality	Integer32
	rcPosLineStatusLocalPeriod	Integer32
	rcPosLineStatusDeviceType	Integer32
	rcPosLineStatusDeviceRev	Integer32
	rcPosLineStatusIpxRoutingProtocol	Integer32

RcPosLineConfigEntry
SEQUENCE
	rcPosLineConfigIndex	InterfaceIndex
	rcPosLineConfigLocalMACAddress	MacAddress
	rcPosLineConfigRemoteMACAddress	MacAddress
	rcPosLineConfigLocalIpAddr	IpAddress
	rcPosLineConfigRemoteIpAddr	IpAddress
	rcPosLineConfigRemoteReportPeriod	INTEGER
	rcPosLineConfigLqrThreshold	INTEGER
	rcPosLineConfigOutQuality	Integer32
	rcPosLineConfigPppStp	EnableValue
	rcPosLineConfigLoopBack	TruthValue
	rcPosLineConfigIpxVlanMacAddress	MacAddress
	rcPosLineConfigIpxRemoteMacAddress	MacAddress

RcPosSioCardConfigEntry
SEQUENCE
	rcPosSioCardConfigSlotIndex	Integer32
	rcPosSioCardConfigAction	INTEGER
	rcPosSioCardConfigTraceMode	INTEGER
	rcPosSioCardConfigImageFileName	DisplayString

RcPosOperStatusEntry
SEQUENCE
	rcPosOperStatusIndex	InterfaceIndex
	rcPosOperStatusLqrStatus	Integer32
	rcPosOperStatusLineLqrThreshold	Integer32
	rcPosOperStatusLinkMagicNumber	Integer32
	rcPosOperStatusLinePppStp	EnableValue

RcRadiusServerEntry
SEQUENCE
	rcRadiusServerPriority	INTEGER
	rcRadiusServerAddress	IpAddress
	rcRadiusServerTimeOut	INTEGER
	rcRadiusServerEnable	TruthValue
	rcRadiusServerMaxRetries	INTEGER
	rcRadiusServerUdpPort	INTEGER
	rcRadiusServerSecretKey	DisplayString
	rcRadiusServerAccessRequests	Counter32
	rcRadiusServerAccessAccepts	Counter32
	rcRadiusServerAccessRejects	Counter32
	rcRadiusServerBadResponses	Counter32
	rcRadiusServerPendingRequests	Counter32
	rcRadiusServerClientRetries	Counter32
	rcRadiusServerRowStatus	RowStatus
	rcRadiusServerAcctEnable	TruthValue
	rcRadiusServerAcctUdpPort	INTEGER
	rcRadiusServerAcctOnRequests	Counter32
	rcRadiusServerAcctOffRequests	Counter32
	rcRadiusServerAcctStartRequests	Counter32
	rcRadiusServerAcctStopRequests	Counter32
	rcRadiusServerAcctInterimRequests	Counter32
	rcRadiusServerAcctBadResponses	Counter32
	rcRadiusServerAcctPendingRequests	Counter32
	rcRadiusServerAcctClientRetries	Counter32

RcRadiusServEntry
SEQUENCE
	rcRadiusServPriority	INTEGER
	rcRadiusServAddress	IpAddress
	rcRadiusServTimeOut	INTEGER
	rcRadiusServEnable	TruthValue
	rcRadiusServMaxRetries	INTEGER
	rcRadiusServUdpPort	INTEGER
	rcRadiusServSecretKey	DisplayString
	rcRadiusServAccessRequests	Counter32
	rcRadiusServAccessAccepts	Counter32
	rcRadiusServAccessRejects	Counter32
	rcRadiusServBadResponses	Counter32
	rcRadiusServPendingRequests	Counter32
	rcRadiusServClientRetries	Counter32
	rcRadiusServRowStatus	RowStatus
	rcRadiusServAcctEnable	TruthValue
	rcRadiusServAcctUdpPort	INTEGER
	rcRadiusServAcctOnRequests	Counter32
	rcRadiusServAcctOffRequests	Counter32
	rcRadiusServAcctStartRequests	Counter32
	rcRadiusServAcctStopRequests	Counter32
	rcRadiusServAcctInterimRequests	Counter32
	rcRadiusServAcctBadResponses	Counter32
	rcRadiusServAcctPendingRequests	Counter32
	rcRadiusServAcctClientRetries	Counter32
	rcRadiusServUsedBy	INTEGER
	rcRadiusServNasIpAddress	IpAddress
	rcRadiusServRoundTripTime	DisplayString
	rcRadiusServAccessChallanges	Counter32
	rcRadiusServSourceIpAddr	IpAddress

RcTacacsServerEntry
SEQUENCE
	rcTacacsServerAddressType	InetAddressType
	rcTacacsServerAddress	InetAddress
	rcTacacsServerPortNumber	InetPortNumber
	rcTacacsServerConnectionType	INTEGER
	rcTacacsServerConnectionStatus	INTEGER
	rcTacacsServerTimeout	Integer32
	rcTacacsServerKey	OCTET STRING
	rcTacacsServerSourceIpInterfaceEnabled	TruthValue
	rcTacacsServerSourceIpInterfaceType	InetAddressType
	rcTacacsServerSourceIpInterface	InetAddress
	rcTacacsServerPriority	Integer32
	rcTacacsServerRowStatus	RowStatus

RcIgmpInterfaceExtnEntry
SEQUENCE
	rcIgmpInterfaceExtnIfIndex	InterfaceIndex
	rcIgmpInterfaceExtnSnoopEnable	TruthValue
	rcIgmpInterfaceExtnProxySnoopEnable	TruthValue
	rcIgmpInterfaceExtnMaxAdvertiseInterval	INTEGER
	rcIgmpInterfaceExtnMinAdvertiseInterval	INTEGER
	rcIgmpInterfaceExtnMaxInitialAdvertiseInterval	Integer32
	rcIgmpInterfaceExtnMaxInitialAdvertments	Integer32
	rcIgmpInterfaceExtnNeighborDeadInterval	Integer32
	rcIgmpInterfaceExtnFastLeaveEnable	TruthValue
	rcIgmpInterfaceExtnFastLeavePortMembers	PortSet
	rcIgmpInterfaceExtnMrdiscEnable	TruthValue
	rcIgmpInterfaceExtnDiscoveredRouterPorts	PortSet
	rcIgmpInterfaceExtnSnoopMRouterPorts	PortSet
	rcIgmpInterfaceExtnSnoopActiveMRouterPorts	PortSet
	rcIgmpInterfaceExtnSnoopMRouterExpiration	Integer32
	rcIgmpInterfaceExtnFlushAction	INTEGER
	rcIgmpInterfaceExtnRouterAlertEnable	EnableValue
	rcIgmpInterfaceExtnSsmEnable	TruthValue
	rcIgmpInterfaceExtnIgapEnable	EnableValue
	rcIgmpInterfaceExtnAccntEnable	EnableValue
	rcIgmpInterfaceExtnAuthEnable	EnableValue
	rcIgmpInterfaceExtnStreamLimitEnable	EnableValue
	rcIgmpInterfaceExtnMaxStreams	Integer32
	rcIgmpInterfaceExtnNumStreams	Integer32
	rcIgmpInterfaceExtnNewQuerier	IpAddress
	rcIgmpInterfaceExtnSnoopQuerierEnable	TruthValue
	rcIgmpInterfaceExtnSnoopQuerierAddr	IpAddress
	rcIgmpInterfaceExtnMvrEnable	TruthValue
	rcIgmpInterfaceExtnMvrProxyEnable	TruthValue
	rcIgmpInterfaceExtnDynamicDowngradeEnable	TruthValue
	rcIgmpInterfaceExtnCompatibilityModeEnable	TruthValue
	rcIgmpInterfaceExtnOperVersion	INTEGER

RcIgmpStaticEntry
SEQUENCE
	rcIgmpStaticIfIndex	InterfaceIndex
	rcIgmpStaticGrpAddr	IpAddress
	rcIgmpStaticMemberPorts	PortSet
	rcIgmpStaticNotAllowedToJoin	PortSet
	rcIgmpStaticRowStatus	RowStatus
	rcIgmpStaticToGrpAddr	IpAddress

RcIgmpAccessEntry
SEQUENCE
	rcIgmpAccessIfIndex	InterfaceIndex
	rcIgmpAccessGrpAddr	IpAddress
	rcIgmpAccessHostAddr	IpAddress
	rcIgmpAccessMode	INTEGER
	rcIgmpAccessRowStatus	RowStatus
	rcIgmpAccessHostMask	IpAddress

RcIgmpSenderEntry
SEQUENCE
	rcIgmpSenderGrpAddr	IpAddress
	rcIgmpSenderIfIndex	InterfaceIndex
	rcIgmpSenderMemberAddr	IpAddress
	rcIgmpSenderAction	INTEGER
	rcIgmpSenderTPort	Integer32
	rcIgmpSenderState	INTEGER

RcIgmpSsmEntry
SEQUENCE
	rcIgmpSsmIpMulticastGrp	IpAddress
	rcIgmpSsmIpSource	IpAddress
	rcIgmpSsmLearningMode	INTEGER
	rcIgmpSsmActivity	TruthValue
	rcIgmpSsmAdminState	EnableValue
	rcIgmpSsmRowStatus	RowStatus

RcIgmpNewAccessEntry
SEQUENCE
	rcIgmpNewAccessIfIndex	InterfaceIndex
	rcIgmpNewAccessPrefixListId	Integer32
	rcIgmpNewAccessPrefixListName	DisplayString
	rcIgmpNewAccessHostAddr	IpAddress
	rcIgmpNewAccessHostMask	IpAddress
	rcIgmpNewAccessActionMode	INTEGER
	rcIgmpNewAccessRowStatus	RowStatus

RcIgmpChannelLimitEntry
SEQUENCE
	rcIgmpChannelLimitIfIndex	InterfaceIndex
	rcIgmpChannelLimitPort	Integer32
	rcIgmpChannelLimitMaxStreams	Integer32
	rcIgmpChannelLimitNumStreams	Integer32
	rcIgmpChannelLimitRowStatus	RowStatus

RcIgmpIgapServiceAbilityEntry
SEQUENCE
	rcIgmpIgapServiceAbilityIfIndex	InterfaceIndex
	rcIgmpIgapServiceAbilityAuthSuccess	Counter64
	rcIgmpIgapServiceAbilityAuthReject	Counter64
	rcIgmpIgapServiceAbilityRespTimeout	Counter64
	rcIgmpIgapServiceAbilityPapJoinReq	Counter64
	rcIgmpIgapServiceAbilityBasicQuery	Counter64
	rcIgmpIgapServiceAbilityBasicLeave	Counter64
	rcIgmpIgapServiceAbilityClearStat	TruthValue

RcIgmpCacheExtnEntry
SEQUENCE
	rcIgmpCacheExtnType	INTEGER
	rcIgmpCacheExtnStaticPorts	PortSet

RcIgmpSnoopTraceEntry
SEQUENCE
	rcIgmpSnoopGrpAddr	IpAddress
	rcIgmpSnoopSrcAddr	IpAddress
	rcIgmpSnoopOutVlan	InterfaceIndex
	rcIgmpSnoopInPort	InterfaceIndex
	rcIgmpSnoopInVlan	InterfaceIndex
	rcIgmpSnoopOutPort	PortSet

RcIgmpNewGroupEntry
SEQUENCE
	rcIgmpNewGroupIpAddress	IpAddress
	rcIgmpNewGroupMembers	IpAddress
	rcIgmpNewGroupInPort	INTEGER
	rcIgmpNewGroupExpiration	Integer32
	rcIgmpNewGroupIfIndex	InterfaceIndex
	rcIgmpNewGroupUserId	DisplayString
	rcIgmpNewGroupMemberState	INTEGER
	rcIgmpNewGroupSessionTime	Integer32

RcIgmpMvrGroupEntry
SEQUENCE
	rcIgmpMvrGroupGroupAddress	IpAddress
	rcIgmpMvrGroupVlanId	Integer32
	rcIgmpMvrGroupIgmpVersion	Integer32
	rcIgmpMvrGroupLivingTime	Integer32

RcIgmpMvrVlanEntry
SEQUENCE
	rcIgmpMvrVlanMvrVlanId	Integer32
	rcIgmpMvrVlanMvrVlanProxy	TruthValue
	rcIgmpMvrVlanSourcePort	Integer32
	rcIgmpMvrVlanSourceAddress	IpAddress

RcIgmpMvrReceiverEntry
SEQUENCE
	rcIgmpMvrReceiverVlanId	Integer32
	rcIgmpMvrReceiverRowStatus	RowStatus

RcPlugOptModEntry
SEQUENCE
	rcPlugOptModPortIndex	InterfaceIndex
	rcPlugOptModDdmStatusMask	BITS
	rcPlugOptModCalibration	INTEGER
	rcPlugOptModPowerMeasure	INTEGER
	rcPlugOptModConnectorType	DisplayString	Size(17)
	rcPlugOptModVendorName	DisplayString	Size(17)
	rcPlugOptModVendorPartNumber	DisplayString	Size(17)
	rcPlugOptModVendorRevNumber	DisplayString	Size(5)
	rcPlugOptModVendorSN	DisplayString	Size(17)
	rcPlugOptModVendorDateCode	DisplayString	Size(9)
	rcPlugOptModPEC	DisplayString	Size(17)
	rcPlugOptModCLEI	DisplayString	Size(11)
	rcPlugOptModSupportsDDM	TruthValue
	rcPlugOptModAux1Monitoring	INTEGER
	rcPlugOptModAux2Monitoring	INTEGER
	rcPlugOptModWaveLength	Integer32
	rcPlugOptModTemperature	Integer32
	rcPlugOptModTemperatureHighAlarmThreshold	Integer32
	rcPlugOptModTemperatureLowAlarmThreshold	Integer32
	rcPlugOptModTemperatureHighWarningThreshold	Integer32
	rcPlugOptModTemperatureLowWarningThreshold	Integer32
	rcPlugOptModVoltage	Integer32
	rcPlugOptModVoltageHighAlarmThreshold	Integer32
	rcPlugOptModVoltageLowAlarmThreshold	Integer32
	rcPlugOptModVoltageHighWarningThreshold	Integer32
	rcPlugOptModVoltageLowWarningThreshold	Integer32
	rcPlugOptModBias	Integer32
	rcPlugOptModBiasHighAlarmThreshold	Integer32
	rcPlugOptModBiasLowAlarmThreshold	Integer32
	rcPlugOptModBiasHighWarningThreshold	Integer32
	rcPlugOptModBiasLowWarningThreshold	Integer32
	rcPlugOptModTxPower	Integer32
	rcPlugOptModTxPowerHighAlarmThreshold	Integer32
	rcPlugOptModTxPowerLowAlarmThreshold	Integer32
	rcPlugOptModTxPowerHighWarningThreshold	Integer32
	rcPlugOptModTxPowerLowWarningThreshold	Integer32
	rcPlugOptModRxPower	Integer32
	rcPlugOptModRxPowerHighAlarmThreshold	Integer32
	rcPlugOptModRxPowerLowAlarmThreshold	Integer32
	rcPlugOptModRxPowerHighWarningThreshold	Integer32
	rcPlugOptModRxPowerLowWarningThreshold	Integer32
	rcPlugOptModAux1	Integer32
	rcPlugOptModAux1HighAlarmThreshold	Integer32
	rcPlugOptModAux1LowAlarmThreshold	Integer32
	rcPlugOptModAux1HighWarningThreshold	Integer32
	rcPlugOptModAux1LowWarningThreshold	Integer32
	rcPlugOptModAux2	Integer32
	rcPlugOptModAux2HighAlarmThreshold	Integer32
	rcPlugOptModAux2LowAlarmThreshold	Integer32
	rcPlugOptModAux2HighWarningThreshold	Integer32
	rcPlugOptModAux2LowWarningThreshold	Integer32
	rcPlugOptModTemperatureStatus	INTEGER
	rcPlugOptModVoltageStatus	INTEGER
	rcPlugOptModBiasStatus	INTEGER
	rcPlugOptModTxPowerStatus	INTEGER
	rcPlugOptModRxPowerStatus	INTEGER
	rcPlugOptModAux1Status	INTEGER
	rcPlugOptModAux2Status	INTEGER

RcVrrpOperEntry
SEQUENCE
	rcVrrpOperIfIndex	InterfaceIndexOrZero
	rcVrrpOperVrId	VrId
	rcVrrpOperIpAddr	IpAddress
	rcVrrpOperVirtualMacAddr	MacAddress
	rcVrrpOperState	INTEGER
	rcVrrpOperControl	INTEGER
	rcVrrpOperPriority	Integer32
	rcVrrpOperIpAddrCount	Integer32
	rcVrrpOperMasterIpAddr	IpAddress
	rcVrrpOperAuthType	INTEGER
	rcVrrpOperHMACMD5Key	OCTET STRING
	rcVrrpOperAuthKey	OCTET STRING
	rcVrrpOperAdvertisementInterval	Integer32
	rcVrrpOperPreemptMode	INTEGER
	rcVrrpOperVirtualRouterUpTime	TimeTicks
	rcVrrpOperRowStatus	RowStatus
	rcVrrpOperCriticalIpAddr	IpAddress
	rcVrrpOperHoldDownTimer	INTEGER
	rcVrrpOperHoldDownState	INTEGER
	rcVrrpOperHoldDownTimeRemaining	INTEGER
	rcVrrpOperAction	INTEGER
	rcVrrpOperCriticalIpAddrEnable	TruthValue
	rcVrrpOperBackUpMaster	INTEGER
	rcVrrpOperBackUpMasterState	INTEGER
	rcVrrpOperFasterAdvInterval	Integer32
	rcVrrpOperFasterAdvIntervalEnable	INTEGER

RcVrrpRouterStatsEntry
SEQUENCE
	rcVrrpStatsIfIndex	Integer32
	rcVrrpStatsVrId	VrId
	rcVrrpStatsBecomeMaster	Counter32
	rcVrrpStatsAdvertiseRcvd	Counter32
	rcVrrpStatsAdvertiseIntervalErrors	Counter32
	rcVrrpStatsPasswdSecurityViolations	Counter32
	rcVrrpStatsHmacSecurityViolations	Counter32
	rcVrrpStatsIpTtlErrors	Counter32
	rcVrrpStatsPriorityZeroPktsRcvd	Counter32
	rcVrrpStatsPriorityZeroPktsSent	Counter32
	rcVrrpStatsInvalidTypePktsRcvd	Counter32
	rcVrrpStatsAddressListErrors	Counter32
	rcVrrpStatsUnknownAuthType	Counter32
	rcVrrpStatsAuthTypeErrors	Counter32

RcNtpServerEntry
SEQUENCE
	rcNtpServerAddress	IpAddress
	rcNtpServerEnable	TruthValue
	rcNtpServerAuthentication	TruthValue
	rcNtpServerKeyId	INTEGER
	rcNtpServerAccessAttempts	Counter32
	rcNtpServerAccessSuccess	Counter32
	rcNtpServerAccessFailure	Counter32
	rcNtpServerRowStatus	RowStatus
	rcNtpServerStratum	DisplayString
	rcNtpServerVersion	DisplayString
	rcNtpServerRootDelay	DisplayString
	rcNtpServerPrecision	DisplayString
	rcNtpServerReachable	DisplayString
	rcNtpServerSynchronized	DisplayString

RcNtpKeyEntry
SEQUENCE
	rcNtpKeyId	INTEGER
	rcNtpKeySecret	DisplayString
	rcNtpKeyRowStatus	RowStatus

RcSvlanEntry
SEQUENCE
	rcSvlanId	INTEGER
	rcSvlanLevel	Integer32
	rcSvlanEtherType	Integer32

Rc2kCpuEthernetPortEntry
SEQUENCE
	rc2kCpuEthernetPortIfIndex	InterfaceIndex
	rc2kCpuEthernetPortDescr	DisplayString
	rc2kCpuEthernetPortAdminStatus	INTEGER
	rc2kCpuEthernetPortOperStatus	INTEGER
	rc2kCpuEthernetPortAddr	IpAddress
	rc2kCpuEthernetPortMask	IpAddress
	rc2kCpuEthernetPortGateway	IpAddress
	rc2kCpuEthernetPortNetwork	IpAddress
	rc2kCpuEthernetPortAutoNegotiate	TruthValue
	rc2kCpuEthernetPortAdminDuplex	INTEGER
	rc2kCpuEthernetPortOperDuplex	INTEGER
	rc2kCpuEthernetPortAdminSpeed	INTEGER
	rc2kCpuEthernetPortOperSpeed	INTEGER
	rc2kCpuEthernetPortEnableBootp	TruthValue
	rc2kCpuEthernetPortMgmtMacAddr	MacAddress

Rc2kCpuSerialPortEntry
SEQUENCE
	rc2kCpuSerialPortIfIndex	InterfaceIndex
	rc2kCpuSerialPortDescr	DisplayString
	rc2kCpuSerialPortMode	INTEGER
	rc2kCpuSerialPortAdminStatus	INTEGER
	rc2kCpuSerialPortOperStatus	INTEGER
	rc2kCpuSerialPortBaudRate	INTEGER
	rc2kCpuSerialPortDataBits	INTEGER
	rc2kCpuSerialPortMyAddr	IpAddress
	rc2kCpuSerialPortPeerAddr	IpAddress
	rc2kCpuSerialPortSlipMtu	INTEGER
	rc2kCpuSerialPortSlipTxRxCompress	TruthValue
	rc2kCpuSerialPortSlipRxCompress	TruthValue
	rc2kCpuSerialPortPppConfigFile	OCTET STRING	Size(0..256)

Rc2kDeviceGlobalEntry
SEQUENCE
	rc2kDeviceGlobalSlot	INTEGER
	rc2kDeviceGlobalFlashBytesUsed	Integer32
	rc2kDeviceGlobalFlashBytesFree	Integer32
	rc2kDeviceGlobalFlashNumFiles	Integer32
	rc2kDeviceGlobalPcmciaBytesUsed	Integer32
	rc2kDeviceGlobalPcmciaBytesFree	Integer32
	rc2kDeviceGlobalPcmciaNumFiles	Integer32
	rc2kDeviceGlobalAction	INTEGER
	rc2kDeviceGlobalResult	INTEGER

Rc2kDeviceFlashFileEntry
SEQUENCE
	rc2kDeviceFlashFileSlot	INTEGER
	rc2kDeviceFlashFileName	DisplayString
	rc2kDeviceFlashFileDate	DisplayString
	rc2kDeviceFlashFileSize	Integer32

Rc2kDevicePcmciaFileEntry
SEQUENCE
	rc2kDevicePcmciaFileSlot	INTEGER
	rc2kDevicePcmciaFileName	DisplayString
	rc2kDevicePcmciaFileDate	DisplayString
	rc2kDevicePcmciaFileSize	Integer32

Rc2kBootConfigEntry
SEQUENCE
	rc2kBootConfigSlot	INTEGER
	rc2kBootConfigLastBootConfigSource	DisplayString
	rc2kBootConfigLastRuntimeImageSource	DisplayString
	rc2kBootConfigLastRuntimeConfigSource	DisplayString
	rc2kBootConfigPrimaryImageSource	DisplayString
	rc2kBootConfigPrimaryConfigSource	DisplayString
	rc2kBootConfigSecondaryImageSource	DisplayString
	rc2kBootConfigSecondaryConfigSource	DisplayString
	rc2kBootConfigTertiaryImageSource	DisplayString
	rc2kBootConfigTertiaryConfigSource	DisplayString
	rc2kBootConfigEnableAutoBoot	TruthValue
	rc2kBootConfigEnableFactoryDefaults	TruthValue
	rc2kBootConfigEnableDebugMode	TruthValue
	rc2kBootConfigEnableHwWatchDogTimer	TruthValue
	rc2kBootConfigEnableRebootOnError	TruthValue
	rc2kBootConfigEnableTelnetServer	TruthValue
	rc2kBootConfigEnableRloginServer	TruthValue
	rc2kBootConfigEnableFtpServer	TruthValue
	rc2kBootConfigEnableTftpServer	TruthValue
	rc2kBootConfigSwVersion	DisplayString
	rc2kBootConfigMulticastConfigProfile	INTEGER
	rc2kBootConfigEnableSshServer	TruthValue
	rc2kBootConfigEnableAltLed	TruthValue
	rc2kBootConfigPrimaryBackupConfigSource	DisplayString
	rc2kBootConfigSecondaryBackupConfigSource	DisplayString
	rc2kBootConfigTertiaryBackupConfigSource	DisplayString
	rc2kBootConfigEnable8616ReAutoneg	TruthValue
	rc2kBootConfigMezzImageSource	DisplayString
	rc2kBootConfigEnableMezz	TruthValue
	rc2kBootConfigPrimaryLicenseSource	DisplayString
	rc2kBootConfigSecondaryLicenseSource	DisplayString
	rc2kBootConfigTertiaryLicenseSource	DisplayString
	rc2kBootConfigEnableCfPcCompat	TruthValue

Rc2kCardEntry
SEQUENCE
	rc2kCardIndex	INTEGER
	rc2kCardFrontType	INTEGER
	rc2kCardFrontDescription	DisplayString
	rc2kCardFrontAdminStatus	INTEGER
	rc2kCardFrontOperStatus	INTEGER
	rc2kCardFrontSerialNum	DisplayString
	rc2kCardFrontHwVersion	DisplayString
	rc2kCardFrontPartNumber	DisplayString
	rc2kCardFrontDateCode	DisplayString
	rc2kCardFrontDeviations	DisplayString
	rc2kCardFrontMacAddr	MacAddress
	rc2kCardBackType	INTEGER
	rc2kCardBackDescription	DisplayString
	rc2kCardBackSerialNum	DisplayString
	rc2kCardBackHwVersion	DisplayString
	rc2kCardBackPartNumber	DisplayString
	rc2kCardBackDateCode	DisplayString
	rc2kCardBackDeviations	DisplayString
	rc2kCardPCMCIAType	INTEGER
	rc2kCardPCMCIADescr	DisplayString
	rc2kCardASICDescr	DisplayString
	rc2kCardFrontMasterIO	TruthValue
	rc2kCardSmltOnSingleCpSupported	TruthValue
	rc2kCardMezzCard	INTEGER
	rc2kCardMezzSerialNum	OCTET STRING
	rc2kCardMezzHwVersion	INTEGER
	rc2kCardMezzPartNum	INTEGER
	rc2kCardSlotPriority	INTEGER
	rc2kCardSlotOriginalPriority	INTEGER
	rc2kCardModuleSerialNum	DisplayString
	rc2kCardModulePartNumber	DisplayString
	rc2kCardModuleAssemblyDate	DisplayString

Rc2kQosQosEntry
SEQUENCE
	rc2kQosQosRow	INTEGER
	rc2kQosQosLevel	INTEGER
	rc2kQosQosName	DisplayString
	rc2kQosQosAdminWeight	Integer32
	rc2kQosQosOperWeight	Integer32
	rc2kQosOctapidMode	INTEGER
	rc2kQosQosAdminThreshold	INTEGER
	rc2kQosQosOperThreshold	INTEGER
	rc2kQosPidMode	INTEGER

Rc2kQosIngressTagToQosEntry
SEQUENCE
	rc2kQosIngressTagToQosRow	INTEGER
	rc2kQosIngressTagToQosInIeee8021P	INTEGER
	rc2kQosIngressTagToQosQosLevel	INTEGER

Rc2kQosIngressDsFieldToQosEntry
SEQUENCE
	rc2kQosIngressDsFieldToQosRow	INTEGER
	rc2kQosIngressDsFieldToQosInDsField	INTEGER
	rc2kQosIngressDsFieldToQosQosLevel	INTEGER

Rc2kQosEgressQosToTagEntry
SEQUENCE
	rc2kQosEgressQosToTagRow	INTEGER
	rc2kQosEgressQosToTagQosLevel	INTEGER
	rc2kQosEgressQosToTagOutIeee8021P	INTEGER

Rc2kQosEgressQosToDsFieldEntry
SEQUENCE
	rc2kQosEgressQosToDsFieldRow	INTEGER
	rc2kQosEgressQosToDsFieldQosLevel	INTEGER
	rc2kQosEgressQosToDsFieldOutDsField	INTEGER

Rc2kQosTrafficProfileEntry
SEQUENCE
	rc2kQosTrafficProfileId	INTEGER
	rc2kQosTrafficProfileName	DisplayString
	rc2kQosTrafficProfileEnable	TruthValue
	rc2kQosTrafficProfileTranslateDscpEnable	TruthValue
	rc2kQosTrafficProfileInProfileDscp	DisplayString	Size(6)
	rc2kQosTrafficProfileOutProfileDscp	DisplayString	Size(6)
	rc2kQosTrafficProfileDiscardEnable	TruthValue
	rc2kQosTrafficProfileAverageRate	Integer32
	rc2kQosTrafficProfilePeakRate	Integer32
	rc2kQosTrafficProfileRowStatus	RowStatus

Rc2kQosIngressDscpToQosEntry
SEQUENCE
	rc2kQosIngressDscpToQosRow	INTEGER
	rc2kQosIngressDscpToQosInDscp	INTEGER
	rc2kQosIngressDscpToQosInDscpBinaryFormat	DisplayString	Size(6)
	rc2kQosIngressDscpToQosQosLevel	INTEGER

Rc2kQosEgressQosToDscpEntry
SEQUENCE
	rc2kQosEgressQosToDscpRow	INTEGER
	rc2kQosEgressQosToDscpQosLevel	INTEGER
	rc2kQosEgressQosToDscpOutDscp	INTEGER
	rc2kQosEgressQosToDscpOutDscpBinaryFormat	DisplayString	Size(6)

Rc2kAtmPortEntry
SEQUENCE
	rc2kAtmPortIfIndex	InterfaceIndex
	rc2kAtmPortNumVpiBits	INTEGER
	rc2kAtmPortNumVciBits	INTEGER
	rc2kAtmPortMediaType	INTEGER
	rc2kAtmPortScrambleEnable	TruthValue
	rc2kAtmPortFramingMode	INTEGER
	rc2kAtmPortClockSource	INTEGER
	rc2kAtmPortLineSpeed	INTEGER
	rc2kAtmPortLoopBackMode	INTEGER
	rc2kAtmPortMacAddress	MacAddress

Rc2kAtmPvcEntry
SEQUENCE
	rc2kAtmPvcIfIndex	InterfaceIndex
	rc2kAtmPvcVpi	INTEGER
	rc2kAtmPvcVci	INTEGER
	rc2kAtmPvcPvcId	Integer32
	rc2kAtmPvcName	DisplayString
	rc2kAtmPvcEncapsulation	INTEGER
	rc2kAtmPvcServiceType	INTEGER
	rc2kAtmPvcPeakCellRate	INTEGER
	rc2kAtmPvcSustainedCellRate	INTEGER
	rc2kAtmPvcMaxBurstSize	INTEGER
	rc2kAtmPvcRowStatus	RowStatus
	rc2kAtmPvcOamLbMgmtEnable	TruthValue
	rc2kAtmPvcOamLbSendFrequency	INTEGER
	rc2kAtmPvcOamLbRetryFrequency	INTEGER
	rc2kAtmPvcOamLbUpCount	INTEGER
	rc2kAtmPvcOamLbDownCount	INTEGER
	rc2kAtmPvcOamTrapEnable	TruthValue
	rc2kAtmPvcOamVcStatus	INTEGER
	rc2kAtmPvcOamLbRequestSent	Counter32
	rc2kAtmPvcOamLbReplySent	Counter32
	rc2kAtmPvcOamLbReplyReceived	Counter32

Rc2kAtm1483ElanEntry
SEQUENCE
	rc2kAtm1483ElanIfIndex	InterfaceIndex
	rc2kAtm1483ElanElanId	Integer32
	rc2kAtm1483ElanNumPvcIds	INTEGER
	rc2kAtm1483ElanPvcIds	IdList
	rc2kAtm1483ElanVlanId	Integer32
	rc2kAtm1483ElanRowStatus	RowStatus
	rc2kAtm1483ElanConnectType	INTEGER
	rc2kAtm1483ElanVlanMacAddress	MacAddress
	rc2kAtm1483ElanDummyMacAddress	MacAddress
	rc2kAtm1483ElanLocalIpAddress	IpAddress
	rc2kAtm1483ElanRemoteIpAddress	IpAddress
	rc2kAtm1483ElanInArpSendEnable	TruthValue
	rc2kAtm1483ElanInArpSendInterval	INTEGER
	rc2kAtm1483ElanIpxVlanEncapMethod	INTEGER
	rc2kAtm1483ElanIpxNetworkNum	INTEGER
	rc2kAtm1483ElanStgId	Integer32
	rc2kAtm1483ElanrcStgTaggedBpduVlanId	Integer32
	rc2kAtm1483ElanIpxNetworkAddr	OCTET STRING	Size(4)

Rc2kAtmSioCardConfigEntry
SEQUENCE
	rc2kAtmSioCardConfigSlotIndex	Integer32
	rc2kAtmSioCardConfigAction	INTEGER
	rc2kAtmSioCardConfigTraceMode	INTEGER
	rc2kAtmSioCardConfigImageFileName	DisplayString
	rc2kAtmSioCardConfigElanStatsEnable	INTEGER
	rc2kAtmSioCardConfigStatsPollPeriod	INTEGER

Rc2kAtmPortStatsEntry
SEQUENCE
	rc2kAtmPortStatsIfIndex	InterfaceIndex
	rc2kAtmPortStatsInCells	Counter64
	rc2kAtmPortStatsOutCells	Counter64
	rc2kAtmPortStatsOutIdleCells	Counter64
	rc2kAtmPortStatsInHecCorrected	Counter32
	rc2kAtmPortStatsInHecUncorrected	Counter32
	rc2kAtmPortStatsInUnknownProtos	Counter32
	rc2kAtmPortStatsInPkts	Counter32
	rc2kAtmPortStatsOutPkts	Counter32
	rc2kAtmPortStatsInDroppedPkts	Counter32
	rc2kAtmPortStatsOutDroppedPkts	Counter32

Rc2kAtmVPortStatsEntry
SEQUENCE
	rc2kAtmVPortStatsIfIndex	InterfaceIndex
	rc2kAtmVPortStatsVlanId	Integer32
	rc2kAtmVPortStatsClear	INTEGER
	rc2kAtmVPortStatsInOctets	Counter64
	rc2kAtmVPortStatsOutOctets	Counter64
	rc2kAtmVPortStatsInErrors	Counter32
	rc2kAtmVPortStatsOutErrors	Counter32
	rc2kAtmVPortStatsInDiscards	Counter32
	rc2kAtmVPortStatsOutDiscards	Counter32
	rc2kAtmVPortStatsInUcastPkts	Counter32
	rc2kAtmVPortStatsOutUcastPkts	Counter32
	rc2kAtmVPortStatsInMulticastPkts	Counter32
	rc2kAtmVPortStatsOutMulticastPkts	Counter32
	rc2kAtmVPortStatsInBroadcastPkts	Counter32
	rc2kAtmVPortStatsOutBroadcastPkts	Counter32

Rc2kMdaCardEntry
SEQUENCE
	rc2kMdaCardSlotNum	INTEGER
	rc2kMdaCardMdaNum	INTEGER
	rc2kMdaCardType	INTEGER
	rc2kMdaCardDescription	DisplayString
	rc2kMdaCardAdminStatus	INTEGER
	rc2kMdaCardOperStatus	INTEGER
	rc2kMdaCardSerialNum	DisplayString
	rc2kMdaCardHwVersion	DisplayString
	rc2kMdaCardPartNumber	DisplayString
	rc2kMdaCardDateCode	DisplayString
	rc2kMdaCardDeviations	DisplayString
	rc2kMdaCardMacAddr	MacAddress
	rc2kMdaCardNumPorts	Integer32
	rc2kMdaCardFirstIfIndex	InterfaceIndex
	rc2kMdaCardLastIfIndex	InterfaceIndex

Rc2kCpuEthernetPortRouteEntry
SEQUENCE
	rc2kCpuEthernetPortRouteNetwork	IpAddress
	rc2kCpuEthernetPortRouteGateway	IpAddress
	rc2kCpuEthernetPortRouteRowStatus	RowStatus

Rc2kCpuEthernetPortIpv6RouteEntry
SEQUENCE
	rc2kCpuEthernetPortIpv6RouteNetwork	Ipv6Address
	rc2kCpuEthernetPortIpv6RoutePrefixLength	INTEGER
	rc2kCpuEthernetPortIpv6RouteGateway	Ipv6Address
	rc2kCpuEthernetPortIpv6RouteRowStatus	RowStatus

RcTengDot3StatsEntry
SEQUENCE
	rcTengDot3StatsIndex	Integer32
	rcTengDot3StatsAlignmentErrors	Counter64
	rcTengDot3StatsFCSErrors	Counter64
	rcTengDot3StatsSingleCollisionFrames	Counter64
	rcTengDot3StatsMultipleCollisionFrames	Counter64
	rcTengDot3StatsSQETestErrors	Counter64
	rcTengDot3StatsDeferredTransmissions	Counter64
	rcTengDot3StatsLateCollisions	Counter64
	rcTengDot3StatsExcessiveCollisions	Counter64
	rcTengDot3StatsInternalMacTransmitErrors	Counter64
	rcTengDot3StatsCarrierSenseErrors	Counter64
	rcTengDot3StatsFrameTooLongs	Counter64
	rcTengDot3StatsInternalMacReceiveErrors	Counter64
	rcTengDot3StatsEtherChipSet	OBJECT IDENTIFIER
	rcTengDot3StatsLinkFailures	Counter32
	rcTengDot3StatsPacketErrors	Counter32
	rcTengDot3StatsCarrierErrors	Counter32
	rcTengDot3StatsLinkInactiveErrors	Counter32
	rcTengDot3StatsInFlowCtrlPkts	Counter64
	rcTengDot3StatsOutFlowCtrlPkts	Counter64
	rcTengDot3StatsFrameTooShorts	Counter64

RcTengStatEntry
SEQUENCE
	rcTengStatIndex	Integer32
	rcTengStatBridgeInUnicastFrames	Counter32
	rcTengStatBridgeInMulticastFrames	Counter32
	rcTengStatBridgeInBroadcastFrames	Counter32
	rcTengStatBridgeInDiscards	Counter32
	rcTengStatBridgeOutUnicastFrames	Counter32
	rcTengStatBridgeOutMulticastFrames	Counter32
	rcTengStatBridgeOutBroadcastFrames	Counter32
	rcTengStatRouteInUnicastFrames	Counter32
	rcTengStatRouteInMulticastFrames	Counter32
	rcTengStatRouteInDiscards	Counter32
	rcTengStatRouteOutUnicastFrames	Counter32
	rcTengStatRouteOutMulticastFrames	Counter32
	rcTengStatStgForwardTransitions	Counter32
	rcTengStatStgInConfigBpdus	Counter32
	rcTengStatStgInTcnBpdus	Counter32
	rcTengStatStgInBadBpdus	Counter32
	rcTengStatStgOutConfigBpdus	Counter32
	rcTengStatStgOutTcnBpdus	Counter32
	rcTengStatBridgeOutFrames	Counter32

RcTengIfEntry
SEQUENCE
	rcTengIfIndex	InterfaceIndex
	rcTengIfDescr	DisplayString
	rcTengIfType	INTEGER
	rcTengIfMtu	Integer32
	rcTengIfSpeed	Gauge32
	rcTengIfPhysAddress	PhysAddress
	rcTengIfAdminStatus	INTEGER
	rcTengIfOperStatus	INTEGER
	rcTengIfLastChange	TimeTicks
	rcTengIfInOctets	Counter64
	rcTengIfInUcastPkts	Counter64
	rcTengIfInNUcastPkts	Counter64
	rcTengIfInDiscards	Counter64
	rcTengIfInErrors	Counter64
	rcTengIfInUnknownProtos	Counter64
	rcTengIfOutOctets	Counter64
	rcTengIfOutUcastPkts	Counter64
	rcTengIfOutNUcastPkts	Counter64
	rcTengIfOutDiscards	Counter64
	rcTengIfOutErrors	Counter64
	rcTengIfOutQLen	Gauge32
	rcTengIfSpecific	OBJECT IDENTIFIER

RcTengIfXEntry
SEQUENCE
	rcTengIfXIndex	InterfaceIndex
	rcTengIfName	DisplayString
	rcTengIfInMulticastPkts	Counter64
	rcTengIfInBroadcastPkts	Counter64
	rcTengIfOutMulticastPkts	Counter64
	rcTengIfOutBroadcastPkts	Counter64
	rcTengIfHCInOctets	Counter64
	rcTengIfHCInUcastPkts	Counter64
	rcTengIfHCInMulticastPkts	Counter64
	rcTengIfHCInBroadcastPkts	Counter64
	rcTengIfHCOutOctets	Counter64
	rcTengIfHCOutUcastPkts	Counter64
	rcTengIfHCOutMulticastPkts	Counter64
	rcTengIfHCOutBroadcastPkts	Counter64
	rcTengIfLinkUpDownTrapEnable	INTEGER
	rcTengIfHighSpeed	Gauge32
	rcTengIfPromiscuousMode	TruthValue
	rcTengIfConnectorPresent	TruthValue

RcRecReservEntry
SEQUENCE
	rcRecReservRecordType	INTEGER
	rcRecReservUsed	Integer32
	rcRecReservReserved	Integer32
	rcRecReservNewReserved	Integer32
	rcRecReservDefReserved	Integer32

RcSslMipEntry
SEQUENCE
	rcSslMipSlot	Integer32
	rcSslMipMip	DisplayString

RcGlobalMacFilterEntry
SEQUENCE
	rcGlobalMacFilterAddress	MacAddress
	rcGlobalMacFilterRowStatus	RowStatus

LaneSet
The set of lanes that are members of this Global Policer. The string is 4 octets long, for a total of 32 bits. Each bit corresponds to a laneId. Each I/O slot has 4 laneIds. When a bit has the value one(1), the corresponding laneId is a member of the set. When a bit has the value zero(0), the corresponding laneId is not a member of the set. The encoding is such that the most significant bit of octet #1 corresponds to laneId 0, while the least significant bit of octet #4 corresponds to laneId 31.
TEXTUAL-CONVENTION
	OCTET STRING	Size(4)

IsisPlsbNodeNickName
Plsb Node Nick name.
TEXTUAL-CONVENTION
	OCTET STRING	Size(3)

IsisSystemID
A system ID.
TEXTUAL-CONVENTION
	OCTET STRING	Size(6)

RcPrQosPolicyEntry
SEQUENCE
	rcPrQosPolicyGpId	INTEGER
	rcPrQosPolicyName	DisplayString
	rcPrQosPolicyPeakRate	INTEGER
	rcPrQosPolicySvcRate	INTEGER
	rcPrQosPolicyLaneMembers	LaneSet
	rcPrQosPolicyRowStatus	RowStatus

RcPrQosLocalPolicyEntry
SEQUENCE
	rcPrQosLocalPolicyGpId	INTEGER
	rcPrQosLocalPolicyIndex	Integer32
	rcPrQosLocalPolicyPeakRate	INTEGER
	rcPrQosLocalPolicySvcRate	INTEGER
	rcPrQosLocalPolicyTotalPkts	Counter64
	rcPrQosLocalPolicyTotalBytes	Counter64
	rcPrQosLocalPolicyBytesOverPeak	Counter64
	rcPrQosLocalPolicyBytesOverSvc	Counter64
	rcPrQosLocalPolicyTotalPktsDropped	Counter64
	rcPrQosLocalPolicyLaneMember	OCTET STRING

RcPrQosTxQueueTemplateEntry
SEQUENCE
	rcPrQosTxQueueTemplateId	INTEGER
	rcPrQosTxQueueTemplateName	DisplayString
	rcPrQosTxQueueTemplateMaxQueues	INTEGER
	rcPrQosTxQueueTemplateBalancedQueues	INTEGER
	rcPrQosTxQueueTemplateHiPriQueues	INTEGER
	rcPrQosTxQueueTemplateLoPriQueues	INTEGER
	rcPrQosTxQueueTemplateTotalQueues	Integer32
	rcPrQosTxQueueTemplateBalancedQList	OCTET STRING
	rcPrQosTxQueueTemplateHiPriQList	OCTET STRING
	rcPrQosTxQueueTemplateLoPriQList	OCTET STRING
	rcPrQosTxQueueTemplateTotalQLists	OCTET STRING
	rcPrQosTxQueueTemplateMinRateTotal	INTEGER
	rcPrQosTxQueueTemplateMaxRateHiPri	INTEGER
	rcPrQosTxQueueTemplatePortMembers	PortSet
	rcPrQosTxQueueTemplateFlags	INTEGER
	rcPrQosTxQueueTemplateApply	TruthValue
	rcPrQosTxQueueTemplateRowStatus	RowStatus

RcPrQosTxQueueEntry
SEQUENCE
	rcPrQosTxQueueTid	INTEGER
	rcPrQosTxQueueQid	INTEGER
	rcPrQosTxQueueName	DisplayString
	rcPrQosTxQueueStyle	INTEGER
	rcPrQosTxQueueWeight	Integer32
	rcPrQosTxQueueMaxRate	Integer32
	rcPrQosTxQueueMinRate	Integer32
	rcPrQosTxQueueBquantum	Integer32
	rcPrQosTxQueueMaxLength	Integer32
	rcPrQosTxQueueWredCurveSet	INTEGER
	rcPrQosTxQueueRowStatus	RowStatus

RcPrQosTxQueueStatsEntry
SEQUENCE
	rcPrQosTxQueueStatsPort	InterfaceIndex
	rcPrQosTxQueueStatsQid	INTEGER
	rcPrQosTxQueueStatsTotalPages	Counter64
	rcPrQosTxQueueStatsDroppedPages	Counter64
	rcPrQosTxQueueStatsUtilization	INTEGER

RcPrQosIngressExpToQosEntry
SEQUENCE
	rcPrQosIngressExpToQosIndex	INTEGER
	rcPrQosIngressExpToQosMplsExp	INTEGER
	rcPrQosIngressExpToQosLevel	INTEGER
	rcPrQosIngressExpToQosRowStatus	RowStatus

RcPrQosEgressQosToExpEntry
SEQUENCE
	rcPrQosEgressQosToExpIndex	INTEGER
	rcPrQosEgressQosToExpQosLevel	INTEGER
	rcPrQosEgressQosToExpMplsExp	INTEGER
	rcPrQosEgressQosToExpRowStatus	RowStatus

RcPrFilterActEntry
SEQUENCE
	rcPrFilterActId	INTEGER
	rcPrFilterActName	DisplayString
	rcPrFilterActArpAttrs	INTEGER
	rcPrFilterActEthernetAttrs	INTEGER
	rcPrFilterActIpAttrs	INTEGER
	rcPrFilterActProtocolAttrs	INTEGER
	rcPrFilterActApply	TruthValue
	rcPrFilterActRowStatus	RowStatus
	rcPrFilterActIpv6Attrs	INTEGER

RcPrFilterActPatternEntry
SEQUENCE
	rcPrFilterActPatternActId	INTEGER
	rcPrFilterActPatternIndex	INTEGER
	rcPrFilterActPatternName	DisplayString
	rcPrFilterActPatternBase	INTEGER
	rcPrFilterActPatternOffset	INTEGER
	rcPrFilterActPatternLength	INTEGER
	rcPrFilterActPatternRowStatus	RowStatus

RcPrFilterAclEntry
SEQUENCE
	rcPrFilterAclId	INTEGER
	rcPrFilterAclActId	INTEGER
	rcPrFilterAclName	DisplayString
	rcPrFilterAclType	INTEGER
	rcPrFilterAclAceListSize	INTEGER
	rcPrFilterAclDefaultAction	INTEGER
	rcPrFilterAclGlobalAction	INTEGER
	rcPrFilterAclState	EnableValue
	rcPrFilterAclVlanList	IdList
	rcPrFilterAclPortList	PortSet
	rcPrFilterAclRowStatus	RowStatus
	rcPrFilterAclNumVlanIds	INTEGER
	rcPrFilterAclPktType	INTEGER

RcPrFilterAclStatsEntry
SEQUENCE
	rcPrFilterAclStatsAclId	INTEGER
	rcPrFilterAclStatsMatchDefaultCounterPkts	Counter64
	rcPrFilterAclStatsMatchDefaultOctets	Counter64
	rcPrFilterAclStatsClear	TruthValue

RcPrFilterAceEntry
SEQUENCE
	rcPrFilterAceAclId	INTEGER
	rcPrFilterAceId	INTEGER
	rcPrFilterAceName	DisplayString
	rcPrFilterAceMode	INTEGER
	rcPrFilterAceRemarkDscp	INTEGER
	rcPrFilterAceRemarkDot1Priority	INTEGER
	rcPrFilterAceRedirectNextHop	IpAddress
	rcPrFilterAceRedirectUnreach	INTEGER
	rcPrFilterAcePolice	INTEGER
	rcPrFilterAceAdminState	EnableValue
	rcPrFilterAceOperState	INTEGER
	rcPrFilterAceEgressQueue	INTEGER
	rcPrFilterAceEgressQueue1g	INTEGER
	rcPrFilterAceEgressQueue10g	INTEGER
	rcPrFilterAceEgressQueueNNSC	INTEGER
	rcPrFilterAceFlags	INTEGER
	rcPrFilterAceStopOnMatch	EnableValue
	rcPrFilterAceMltIndex	INTEGER
	rcPrFilterAceRowStatus	RowStatus
	rcPrFilterAceIpfixState	EnableValue
	rcPrFilterAceRedirectNextHopIpv6	Ipv6Address
	rcPrFilterAceDstPortList	PortSet
	rcPrFilterAceDstVlanId	Integer32
	rcPrFilterAceDstMltId	Integer32

RcPrFilterAceEthSrcAddrEntry
SEQUENCE
	rcPrFilterAceEthSrcAddrAclId	INTEGER
	rcPrFilterAceEthSrcAddrAceId	INTEGER
	rcPrFilterAceEthSrcAddrList	OCTET STRING
	rcPrFilterAceEthSrcAddrListCount	INTEGER
	rcPrFilterAceEthSrcAddrOper	INTEGER
	rcPrFilterAceEthSrcAddrRowStatus	RowStatus

RcPrFilterAceEthDstAddrEntry
SEQUENCE
	rcPrFilterAceEthDstAddrAclId	INTEGER
	rcPrFilterAceEthDstAddrAceId	INTEGER
	rcPrFilterAceEthDstAddrList	OCTET STRING
	rcPrFilterAceEthDstAddrListCount	INTEGER
	rcPrFilterAceEthDstAddrOper	INTEGER
	rcPrFilterAceEthDstAddrRowStatus	RowStatus

RcPrFilterAceEthEtherEntry
SEQUENCE
	rcPrFilterAceEthEtherAclId	INTEGER
	rcPrFilterAceEthEtherAceId	INTEGER
	rcPrFilterAceEthEtherTypeList	OCTET STRING
	rcPrFilterAceEthEtherTypeListCount	INTEGER
	rcPrFilterAceEthEtherTypeOper	INTEGER
	rcPrFilterAceEthEtherRowStatus	RowStatus

RcPrFilterAceEthVlanTagPrioEntry
SEQUENCE
	rcPrFilterAceEthVlanTagPrioAclId	INTEGER
	rcPrFilterAceEthVlanTagPrioAceId	INTEGER
	rcPrFilterAceEthVlanTagPrioVlanTagPrio	INTEGER
	rcPrFilterAceEthVlanTagPrioOper	INTEGER
	rcPrFilterAceEthVlanTagPrioRowStatus	RowStatus

RcPrFilterAceEthPortEntry
SEQUENCE
	rcPrFilterAceEthPortAclId	INTEGER
	rcPrFilterAceEthPortAceId	INTEGER
	rcPrFilterAceEthPortPort	PortSet
	rcPrFilterAceEthPortOper	INTEGER
	rcPrFilterAceEthPortRowStatus	RowStatus

RcPrFilterAceEthVlanIdEntry
SEQUENCE
	rcPrFilterAceEthVlanIdAclId	INTEGER
	rcPrFilterAceEthVlanIdAceId	INTEGER
	rcPrFilterAceEthVlanIdVlanIdList	IdList
	rcPrFilterAceEthVlanIdOper	INTEGER
	rcPrFilterAceEthVlanIdRowStatus	RowStatus

RcPrFilterAceArpEntry
SEQUENCE
	rcPrFilterAceArpAclId	INTEGER
	rcPrFilterAceArpAceId	INTEGER
	rcPrFilterAceArpType	INTEGER
	rcPrFilterAceArpOper	INTEGER
	rcPrFilterAceArpValue	INTEGER
	rcPrFilterAceArpRowStatus	RowStatus

RcPrFilterAceIpSrcAddrEntry
SEQUENCE
	rcPrFilterAceIpSrcAddrAclId	INTEGER
	rcPrFilterAceIpSrcAddrAceId	INTEGER
	rcPrFilterAceIpSrcAddrList	OCTET STRING
	rcPrFilterAceIpSrcAddrListCount	INTEGER
	rcPrFilterAceIpSrcAddrOper	INTEGER
	rcPrFilterAceIpSrcAddrRowStatus	RowStatus

RcPrFilterAceIpDstAddrEntry
SEQUENCE
	rcPrFilterAceIpDstAddrAclId	INTEGER
	rcPrFilterAceIpDstAddrAceId	INTEGER
	rcPrFilterAceIpDstAddrList	OCTET STRING
	rcPrFilterAceIpDstAddrListCount	INTEGER
	rcPrFilterAceIpDstAddrOper	INTEGER
	rcPrFilterAceIpDstAddrRowStatus	RowStatus

RcPrFilterAceIpDscpEntry
SEQUENCE
	rcPrFilterAceIpDscpAclId	INTEGER
	rcPrFilterAceIpDscpAceId	INTEGER
	rcPrFilterAceIpDscpList	OCTET STRING
	rcPrFilterAceIpDscpListCount	INTEGER
	rcPrFilterAceIpDscpOper	INTEGER
	rcPrFilterAceIpDscpRowStatus	RowStatus

RcPrFilterAceIpProtoEntry
SEQUENCE
	rcPrFilterAceIpProtoAclId	INTEGER
	rcPrFilterAceIpProtoAceId	INTEGER
	rcPrFilterAceIpProtoList	OCTET STRING
	rcPrFilterAceIpProtoListCount	INTEGER
	rcPrFilterAceIpProtoOper	INTEGER
	rcPrFilterAceIpProtoRowStatus	RowStatus

RcPrFilterAceIpOptionsEntry
SEQUENCE
	rcPrFilterAceIpOptionsAclId	INTEGER
	rcPrFilterAceIpOptionsAceId	INTEGER
	rcPrFilterAceIpOptionsOptions	INTEGER
	rcPrFilterAceIpOptionsOper	INTEGER
	rcPrFilterAceIpOptionsRowStatus	RowStatus

RcPrFilterAceIpFragEntry
SEQUENCE
	rcPrFilterAceIpFragAclId	INTEGER
	rcPrFilterAceIpFragAceId	INTEGER
	rcPrFilterAceIpFragFragmentation	INTEGER
	rcPrFilterAceIpFragOper	INTEGER
	rcPrFilterAceIpFragRowStatus	RowStatus

RcPrFilterAceProtoTcpSrcPortEntry
SEQUENCE
	rcPrFilterAceProtoTcpSrcPortAclId	INTEGER
	rcPrFilterAceProtoTcpSrcPortAceId	INTEGER
	rcPrFilterAceProtoTcpSrcPortPort	OCTET STRING
	rcPrFilterAceProtoTcpSrcPortCount	INTEGER
	rcPrFilterAceProtoTcpSrcPortOper	INTEGER
	rcPrFilterAceProtoTcpSrcPortRowStatus	RowStatus

RcPrFilterAceProtoUdpSrcPortEntry
SEQUENCE
	rcPrFilterAceProtoUdpSrcPortAclId	INTEGER
	rcPrFilterAceProtoUdpSrcPortAceId	INTEGER
	rcPrFilterAceProtoUdpSrcPortPort	OCTET STRING
	rcPrFilterAceProtoUdpSrcPortCount	INTEGER
	rcPrFilterAceProtoUdpSrcPortOper	INTEGER
	rcPrFilterAceProtoUdpSrcPortRowStatus	RowStatus

RcPrFilterAceProtoTcpDstPortEntry
SEQUENCE
	rcPrFilterAceProtoTcpDstPortAclId	INTEGER
	rcPrFilterAceProtoTcpDstPortAceId	INTEGER
	rcPrFilterAceProtoTcpDstPortPort	OCTET STRING
	rcPrFilterAceProtoTcpDstPortCount	INTEGER
	rcPrFilterAceProtoTcpDstPortOper	INTEGER
	rcPrFilterAceProtoTcpDstPortRowStatus	RowStatus

RcPrFilterAceProtoUdpDstPortEntry
SEQUENCE
	rcPrFilterAceProtoUdpDstPortAclId	INTEGER
	rcPrFilterAceProtoUdpDstPortAceId	INTEGER
	rcPrFilterAceProtoUdpDstPortPort	OCTET STRING
	rcPrFilterAceProtoUdpDstPortCount	INTEGER
	rcPrFilterAceProtoUdpDstPortOper	INTEGER
	rcPrFilterAceProtoUdpDstPortRowStatus	RowStatus

RcPrFilterAceProtoIcmpMsgTypeEntry
SEQUENCE
	rcPrFilterAceProtoIcmpMsgTypeAclId	INTEGER
	rcPrFilterAceProtoIcmpMsgTypeAceId	INTEGER
	rcPrFilterAceProtoIcmpMsgTypeList	OCTET STRING
	rcPrFilterAceProtoIcmpMsgTypeCount	INTEGER
	rcPrFilterAceProtoIcmpMsgTypeOper	INTEGER
	rcPrFilterAceProtoIcmpMsgTypeRowStatus	RowStatus

RcPrFilterAceProtoTcpFlagsEntry
SEQUENCE
	rcPrFilterAceProtoTcpFlagsAclId	INTEGER
	rcPrFilterAceProtoTcpFlagsAceId	INTEGER
	rcPrFilterAceProtoTcpFlagsList	OCTET STRING
	rcPrFilterAceProtoTcpFlagsCount	INTEGER
	rcPrFilterAceProtoTcpFlagsOper	INTEGER
	rcPrFilterAceProtoTcpFlagsRowStatus	RowStatus

RcPrFilterAcePattern1Entry
SEQUENCE
	rcPrFilterAcePattern1AclId	INTEGER
	rcPrFilterAcePattern1AceId	INTEGER
	rcPrFilterAcePattern1Name	DisplayString
	rcPrFilterAcePattern1Value	OCTET STRING
	rcPrFilterAcePattern1Oper	INTEGER
	rcPrFilterAcePattern1RowStatus	RowStatus

RcPrFilterAcePattern2Entry
SEQUENCE
	rcPrFilterAcePattern2AclId	INTEGER
	rcPrFilterAcePattern2AceId	INTEGER
	rcPrFilterAcePattern2Name	DisplayString
	rcPrFilterAcePattern2Value	OCTET STRING
	rcPrFilterAcePattern2Oper	INTEGER
	rcPrFilterAcePattern2RowStatus	RowStatus

RcPrFilterAcePattern3Entry
SEQUENCE
	rcPrFilterAcePattern3AclId	INTEGER
	rcPrFilterAcePattern3AceId	INTEGER
	rcPrFilterAcePattern3Name	DisplayString
	rcPrFilterAcePattern3Value	OCTET STRING
	rcPrFilterAcePattern3Oper	INTEGER
	rcPrFilterAcePattern3RowStatus	RowStatus

RcPrFilterAceStatsEntry
SEQUENCE
	rcPrFilterAceStatsAclId	INTEGER
	rcPrFilterAceStatsAceId	INTEGER
	rcPrFilterAceStatsPortId	INTEGER
	rcPrFilterAceStatsMatchCountPkts	Counter64
	rcPrFilterAceStatsMatchCountOctets	Counter64
	rcPrFilterAceStatsClear	TruthValue

RcPrFilterAceEthShowEntry
SEQUENCE
	rcPrFilterAceEthShowAclId	INTEGER
	rcPrFilterAceEthShowAceId	INTEGER
	rcPrFilterAceEthShowSrcAddrList	OCTET STRING
	rcPrFilterAceEthShowSrcAddrOper	INTEGER
	rcPrFilterAceEthShowDstAddrList	OCTET STRING
	rcPrFilterAceEthShowDstAddrOper	INTEGER
	rcPrFilterAceEthShowEtherTypeList	OCTET STRING
	rcPrFilterAceEthShowEtherTypeOper	INTEGER
	rcPrFilterAceEthShowVlanTagPrio	INTEGER
	rcPrFilterAceEthShowVlanTagPrioOper	INTEGER
	rcPrFilterAceEthShowPort	PortSet
	rcPrFilterAceEthShowPortOper	INTEGER
	rcPrFilterAceEthShowVlanIdList	IdList
	rcPrFilterAceEthShowVlanIdOper	INTEGER

RcPrFilterAceIpShowEntry
SEQUENCE
	rcPrFilterAceIpShowAclId	INTEGER
	rcPrFilterAceIpShowAceId	INTEGER
	rcPrFilterAceIpShowSrcAddrList	OCTET STRING
	rcPrFilterAceIpShowSrcAddrOper	INTEGER
	rcPrFilterAceIpShowDstAddrList	OCTET STRING
	rcPrFilterAceIpShowDstAddrOper	INTEGER
	rcPrFilterAceIpShowDscpList	OCTET STRING
	rcPrFilterAceIpShowDscpOper	INTEGER
	rcPrFilterAceIpShowProtoList	OCTET STRING
	rcPrFilterAceIpShowProtoOper	INTEGER
	rcPrFilterAceIpShowOptions	INTEGER
	rcPrFilterAceIpShowOptionsOper	INTEGER
	rcPrFilterAceIpShowFragmentation	INTEGER
	rcPrFilterAceIpShowFragOper	INTEGER

RcPrFilterAceProtoShowEntry
SEQUENCE
	rcPrFilterAceProtoShowAclId	INTEGER
	rcPrFilterAceProtoShowAceId	INTEGER
	rcPrFilterAceProtoShowTcpSrcPort	OCTET STRING
	rcPrFilterAceProtoShowTcpSrcPortOper	INTEGER
	rcPrFilterAceProtoShowUdpSrcPort	OCTET STRING
	rcPrFilterAceProtoShowUdpSrcPortOper	INTEGER
	rcPrFilterAceProtoShowTcpDstPort	OCTET STRING
	rcPrFilterAceProtoShowTcpDstPortOper	INTEGER
	rcPrFilterAceProtoShowUdpDstPort	OCTET STRING
	rcPrFilterAceProtoShowUdpDstPortOper	INTEGER
	rcPrFilterAceProtoShowIcmpMsgTypeList	OCTET STRING
	rcPrFilterAceProtoShowIcmpMsgTypeOper	INTEGER
	rcPrFilterAceProtoShowTcpFlagsList	OCTET STRING
	rcPrFilterAceProtoShowTcpFlagsOper	INTEGER

RcPrFilterAcePatternShowEntry
SEQUENCE
	rcPrFilterAcePatternShowAclId	INTEGER
	rcPrFilterAcePatternShowAceId	INTEGER
	rcPrFilterAcePatternShowPattern1Name	DisplayString
	rcPrFilterAcePatternShowPattern1Value	OCTET STRING
	rcPrFilterAcePatternShowPattern1Oper	INTEGER
	rcPrFilterAcePatternShowPattern2Name	DisplayString
	rcPrFilterAcePatternShowPattern2Value	OCTET STRING
	rcPrFilterAcePatternShowPattern2Oper	INTEGER
	rcPrFilterAcePatternShowPattern3Name	DisplayString
	rcPrFilterAcePatternShowPattern3Value	OCTET STRING
	rcPrFilterAcePatternShowPattern3Oper	INTEGER

RcPrFilterAceIpv6SrcAddrEntry
SEQUENCE
	rcPrFilterAceIpv6SrcAddrAclId	INTEGER
	rcPrFilterAceIpv6SrcAddrAceId	INTEGER
	rcPrFilterAceIpv6SrcAddrList	OCTET STRING
	rcPrFilterAceIpv6SrcAddrListCount	INTEGER
	rcPrFilterAceIpv6SrcAddrOper	INTEGER
	rcPrFilterAceIpv6SrcAddrRowStatus	RowStatus

RcPrFilterAceIpv6DstAddrEntry
SEQUENCE
	rcPrFilterAceIpv6DstAddrAclId	INTEGER
	rcPrFilterAceIpv6DstAddrAceId	INTEGER
	rcPrFilterAceIpv6DstAddrList	OCTET STRING
	rcPrFilterAceIpv6DstAddrListCount	INTEGER
	rcPrFilterAceIpv6DstAddrOper	INTEGER
	rcPrFilterAceIpv6DstAddrRowStatus	RowStatus

RcPrFilterAceIpv6NextHdrEntry
SEQUENCE
	rcPrFilterAceIpv6NextHdrAclId	INTEGER
	rcPrFilterAceIpv6NextHdrAceId	INTEGER
	rcPrFilterAceIpv6NextHdrNextHdr	Ipv6NextHdr
	rcPrFilterAceIpv6NextHdrOper	INTEGER
	rcPrFilterAceIpv6NextHdrRowStatus	RowStatus

RcPrFilterAceIpv6ShowEntry
SEQUENCE
	rcPrFilterAceIpv6ShowAclId	INTEGER
	rcPrFilterAceIpv6ShowAceId	INTEGER
	rcPrFilterAceIpv6ShowSrcAddrList	OCTET STRING
	rcPrFilterAceIpv6ShowSrcAddrOper	INTEGER
	rcPrFilterAceIpv6ShowDstAddrList	OCTET STRING
	rcPrFilterAceIpv6ShowDstAddrOper	INTEGER
	rcPrFilterAceIpv6ShowNxtHdrNxtHdr	Ipv6NextHdr
	rcPrFilterAceIpv6ShowNxtHdrOper	INTEGER

VPNId
The purpose of a VPN-ID is to uniquely identify a VPN. The Global VPN Identifier format is: 3 octet VPN Authority, Organizationally Unique Identifier followed by 4 octet VPN index identifying VPN according to OUI
TEXTUAL-CONVENTION
	OCTET STRING	Size(7)

VrfRpTriggerBitCode
This object represents Routing Protocol (RP) Triggers on a Virtual Router. The BITS represent an Action-code that specifies the action on the Routing Protocols. The actions are: initiate or shutdown. When encoding the RP using the BITS construct, the value is encoded as an OCTET STRING where the first bit (bit 0) is the highest bit of the octet. Bits 0-3 may be specified in any combination to allow multiple Routing Protocols to be acted on simultaneously or individually.
TEXTUAL-CONVENTION
	BITS	rip(0), ospf(1), bgp(2), isis(3), pim(4), mvr(5)

RcVrfConfigEntry
SEQUENCE
	rcVrfId	VrfIdentifier
	rcVrfRowStatus	RowStatus
	rcVrfName	DisplayString
	rcVrfContextName	SnmpAdminString
	rcVrfTrapEnable	TruthValue
	rcVrfMaxRoutes	Unsigned32
	rcVrfAdminStatus	INTEGER
	rcVrfVpnId	VPNId
	rcVrfRpTrigger	VrfRpTriggerBitCode
	rcVrfMaxRoutesTrapEnable	TruthValue

RcVrfStatEntry
SEQUENCE
	rcVrfStatRouteEntries	Unsigned32
	rcVrfStatFIBEntries	Unsigned32
	rcVrfStatUpTime	TimeTicks
	rcVrfOperStatus	INTEGER
	rcVrfRpStatus	VrfRpTriggerBitCode
	rcVrfRouterAddressType	InetAddressType
	rcVrfRouterAddress	InetAddress

RcIpfixConfSlotEntry
SEQUENCE
	rcIpfixConfSlotNum	Integer32
	rcIpfixConfSlotAgingIntv	Integer32
	rcIpfixConfSlotActiveTimeout	Integer32
	rcIpfixConfSlotExportIntv	Integer32
	rcIpfixConfSlotExportState	EnableValue
	rcIpfixConfSlotTempRefIntvSec	Integer32
	rcIpfixConfSlotTempRefIntvPkts	Integer32

RcIpfixCollectorEntry
SEQUENCE
	rcIpfixCollectorSlotNum	Integer32
	rcIpfixCollectorAddressType	InetAddressType
	rcIpfixCollectorAddress	InetAddress
	rcIpfixCollectorProtocol	INTEGER
	rcIpfixCollectorDestPort	InetPortNumber
	rcIpfixCollectorExporterIpType	InetAddressType
	rcIpfixCollectorExporterIp	InetAddress
	rcIpfixCollectorProtoVer	INTEGER
	rcIpfixCollectorState	TruthValue
	rcIpfixCollectorRowStatus	RowStatus

RcIpfixConfPortEntry
SEQUENCE
	rcIpfixConfPortId	InterfaceIndex
	rcIpfixConfPortSampleRate	Integer32
	rcIpfixConfPortHashPolyCoeffs	Integer32
	rcIpfixConfPortHashPolySeed	Integer32
	rcIpfixConfPortFlush	INTEGER
	rcIpfixConfPortAllTraffic	EnableValue
	rcIpfixConfPortHashKeyId	INTEGER
	rcIpfixConfPortDynamicSampRate	Integer32

RcIpfixHashStatsEntry
SEQUENCE
	rcIpfixHashStatsSlotNum	Integer32
	rcIpfixHashStatsHashOverflows	Counter64
	rcIpfixHashStatsHashDrops	Counter64
	rcIpfixHashStatsClear	INTEGER
	rcIpfixHashStatsClearTime	TimeStamp

RcIpfixExporterStatsEntry
SEQUENCE
	rcIpfixExporterStatsSlotNum	Integer32
	rcIpfixExporterStatsCollectorType	InetAddressType
	rcIpfixExporterStatsCollector	InetAddress
	rcIpfixExporterStatsOutPkts	Counter64
	rcIpfixExporterStatsOutOctets	Counter64
	rcIpfixExporterStatsPktsLoss	Counter64
	rcIpfixExporterStatsClear	INTEGER
	rcIpfixExporterStatsClearTime	TimeStamp

RcIpVpnRouteDistinguisherEntry
SEQUENCE
	rcIpVpnVrfId	VrfIdentifier
	rcIpVpnRouteDistinguisherType	INTEGER
	rcIpVpnRouteDistinguisherAddress	IpAddress
	rcIpVpnRouteDistinguisherAsNumber	INTEGER
	rcIpVpnRouteDistinguisherAssignedNum	Unsigned32
	rcIpVpnRouteDistinguisherRowStatus	RowStatus

RcIpVpnRouteTargetEntry
SEQUENCE
	rcIpVpnRouteTargetIndex	INTEGER
	rcIpVpnRouteTargetType	INTEGER
	rcIpVpnRouteTargetIpAddress	IpAddress
	rcIpVpnRouteTargetAsNumber	INTEGER
	rcIpVpnRouteTargetAssignedNum	Unsigned32
	rcIpVpnRouteTargetRowStatus	RowStatus

RcVrfIpVpnTableEntry
SEQUENCE
	rcVrfIpVpnVrfId	VrfIdentifier
	rcVrfIpVpnStatus	EnableValue
	rcVrfIpVpnImportRTList	IdList
	rcVrfIpVpnExportRTList	IdList
	rcVrfIpVpnSvcLblAllocOpt	INTEGER
	rcVrfIpVpnRowStatus	RowStatus
	rcVrfIpVpnIsidNumber	Integer32

RcSlppVlanEntry
SEQUENCE
	rcSlppVlanVlanId	INTEGER
	rcSlppVlanSlppEnable	TruthValue
	rcSlppVlanRowStatus	RowStatus

RcSlppPortEntry
SEQUENCE
	rcSlppPortIfIndex	InterfaceIndex
	rcSlppPortPktRxThreshold	Integer32
	rcSlppPortSlppEnable	TruthValue
	rcSlppPortIncomingVlanId	Integer32
	rcSlppPortSrcNodeType	INTEGER

RcMplsIpStaticFecEntry
SEQUENCE
	rcMplsIpStaticFecDest	IpAddress
	rcMplsIpStaticFecMask	IpAddress
	rcMplsIpStaticFecTunnelName	DisplayString
	rcMplsIpStaticFecTunnelId	MplsTunnelIndex
	rcMplsIpStaticFecEgressAddr	IpAddress
	rcMplsIpStaticFecEgressMask	IpAddress
	rcMplsIpStaticFecState	INTEGER
	rcMplsIpStaticFecRowStatus	RowStatus

RcMplsIpFtnEntry
SEQUENCE
	rcMplsIpFtnDest	IpAddress
	rcMplsIpFtnMask	IpAddress
	rcMplsIpFtnType	INTEGER
	rcMplsIpFtnOutLabel	MplsLabel
	rcMplsIpFtnOutIfIndex	InterfaceIndex
	rcMplsIpFtnNextHop	IpAddress

RcMplsIpIlmEntry
SEQUENCE
	rcMplsIpIlmInLabel	MplsLabel
	rcMplsIpIlmInIfIndex	InterfaceIndex
	rcMplsIpIlmOutLabel	MplsLabel
	rcMplsIpIlmOutIfIndex	InterfaceIndex
	rcMplsIpIlmNextHop	IpAddress

RcMplsIngressLspStatEntry
SEQUENCE
	rcMplsIngressLspPort	INTEGER
	rcMplsIngressLspLabel	MplsLabel
	rcMplsIngressLspPkts	Counter64

RcMplsEgressLspStatEntry
SEQUENCE
	rcMplsEgressLspPort	INTEGER
	rcMplsEgressLspLabel	MplsLabel
	rcMplsEgressLspPkts	Counter64

RcMplsRsvpTunnelExtEntry
SEQUENCE
	rcMplsRsvpTunnelExtIndex	MplsTunnelIndex
	rcMplsRsvpTunnelExtInstance	MplsTunnelInstanceIndex
	rcMplsRsvpTunnelExtIngressLSRId	MplsExtendedTunnelId
	rcMplsRsvpTunnelExtEgressLSRId	MplsExtendedTunnelId
	rcMplsRsvpTunnelExtName	SnmpAdminString
	rcMplsRsvpTunnelExtSwitchover	TruthValue
	rcMplsRsvpTunnelExtActiveStatus	TruthValue
	rcMplsRsvpTunnelExtResStyle	SnmpAdminString
	rcMplsRsvpTunnelExtLspId	MplsLSPID
	rcMplsRsvpTunnelExtERO	SnmpAdminString
	rcMplsRsvpTunnelExtRRO	SnmpAdminString
	rcMplsRsvpTunnelExtInIfIndex	InterfaceIndex
	rcMplsRsvpTunnelExtInLabel	MplsLabel
	rcMplsRsvpTunnelExtInNeighbor	IpAddress
	rcMplsRsvpTunnelExtOutIfIndex	InterfaceIndex
	rcMplsRsvpTunnelExtOutLabel	MplsLabel
	rcMplsRsvpTunnelExtOutNeighbor	IpAddress
	rcMplsRsvpTunnelExtTSpecRate	Unsigned32
	rcMplsRsvpTunnelExtTSpecSize	Unsigned32
	rcMplsRsvpTunnelExtTSpecPeak	Unsigned32
	rcMplsRsvpTunnelExtTSpecMin	Unsigned32
	rcMplsRsvpTunnelExtTSpecMax	Unsigned32
	rcMplsRsvpTunnelExtInstanceUpTime	TimeTicks
	rcMplsRsvpTunnelExtLSPUpTime	TimeTicks

RcMplsRsvpNeighborEntry
SEQUENCE
	rcMplsRsvpNeighborAddress	IpAddress
	rcMplsRsvpNeighborHelloState	SnmpAdminString
	rcMplsRsvpNeighborIfIndex	InterfaceIndex
	rcMplsRsvpNeighborTime	Integer32
	rcMplsRsvpNeighborPeriod	Integer32
	rcMplsRsvpNeighborSendCnt	Integer32
	rcMplsRsvpNeighborRcvCnt	Integer32
	rcMplsRsvpNeighborLocalInstance	Integer32
	rcMplsRsvpNeighborRemoteInstance	Integer32
	rcMplsRsvpNeighborCreationTime	Integer32
	rcMplsRsvpNeighborLastPktRxTime	Integer32
	rcMplsRsvpNeighborRefReduction	SnmpAdminString

RcMplsRsvpInterfaceEntry
SEQUENCE
	rcMplsRsvpInterfaceIfIndex	InterfaceIndex
	rcMplsRsvpInterfaceAddress	IpAddress
	rcMplsRsvpInterfaceRefreshInterval	Unsigned32
	rcMplsRsvpInterfaceRefreshMult	Unsigned32
	rcMplsRsvpInterfaceHelloInterval	Unsigned32
	rcMplsRsvpInterfaceRefreshReduction	Unsigned32
	rcMplsRsvpInterfaceMessageBundling	Unsigned32

RcMplsRsvpStatsEntry
SEQUENCE
	rcMplsRsvpStatsIfIndex	InterfaceIndex
	rcMplsRsvpStatsPathRcv	Counter32
	rcMplsRsvpStatsPathSent	Counter32
	rcMplsRsvpStatsPathErrRcv	Counter32
	rcMplsRsvpStatsPathErrSent	Counter32
	rcMplsRsvpStatsPathTearRcv	Counter32
	rcMplsRsvpStatsPathTearSent	Counter32
	rcMplsRsvpStatsResvRcv	Counter32
	rcMplsRsvpStatsResvSent	Counter32
	rcMplsRsvpStatsResvErrRcv	Counter32
	rcMplsRsvpStatsResvErrSent	Counter32
	rcMplsRsvpStatsResvTearRcv	Counter32
	rcMplsRsvpStatsResvTearSent	Counter32
	rcMplsRsvpStatsConfTearRcv	Counter32
	rcMplsRsvpStatsConfTearSent	Counter32
	rcMplsRsvpStatsAckRcv	Counter32
	rcMplsRsvpStatsAckSent	Counter32
	rcMplsRsvpStatsSRefreshRcv	Counter32
	rcMplsRsvpStatsSRefreshSent	Counter32
	rcMplsRsvpStatsHelloReqRcv	Counter32
	rcMplsRsvpStatsHelloReqSent	Counter32
	rcMplsRsvpStatsHelloAckRcv	Counter32
	rcMplsRsvpStatsHelloAckSent	Counter32
	rcMplsRsvpStatsBadIpHdr	Counter32
	rcMplsRsvpStatsBadVersion	Counter32
	rcMplsRsvpStatsBadRsvpLen	Counter32
	rcMplsRsvpStatsBadCksum	Counter32
	rcMplsRsvpStatsBadMsgType	Counter32
	rcMplsRsvpStatsBadMsgForm	Counter32
	rcMplsRsvpStatsBadIntf	Counter32
	rcMplsRsvpStatsClear	TruthValue

RcMplsLdpDiscoveryEntry
SEQUENCE
	rcMplsLdpDiscoveryIfIndex	InterfaceIndex
	rcMplsLdpDiscoveryPeerLdpId	MplsLdpIdentifier
	rcMplsLdpDiscoveryPeerTransportAddr	IpAddress
	rcMplsLdpDiscoveryNegotiatedHoldTime	Unsigned32
	rcMplsLdpDiscoveryConfSeqNum	Unsigned32
	rcMplsLdpDiscoveryExtendedDiscovery	Unsigned32

RcMplsLdpPathEntry
SEQUENCE
	rcMplsLdpPathType	INTEGER
	rcMplsLdpPathAddrType	InetAddressType
	rcMplsLdpPathAddrPrefixLength	InetAddressPrefixLength
	rcMplsLdpPathAddr	InetAddress
	rcMplsLdpPathInLabel	MplsLabel

RcMplsLdpPathRemotePeerEntry
SEQUENCE
	rcMplsLdpPathRemotePeerType	INTEGER
	rcMplsLdpPathRemotePeerAddrType	InetAddressType
	rcMplsLdpPathRemotePeerAddrPrefixLength	InetAddressPrefixLength
	rcMplsLdpPathRemotePeerAddr	InetAddress
	rcMplsLdpPathRemotePeerId	INTEGER
	rcMplsLdpPathRemotePeerLdpId	MplsLdpIdentifier
	rcMplsLdpPathRemotePeerOutLabel	MplsLabel
	rcMplsLdpPathRemotePeerState	INTEGER

RcMplsLdpRouteEntry
SEQUENCE
	rcMplsLdpRouteType	INTEGER
	rcMplsLdpRouteAddrType	InetAddressType
	rcMplsLdpRouteAddrPrefixLength	InetAddressPrefixLength
	rcMplsLdpRouteAddr	InetAddress
	rcMplsLdpRouteIfIndex	InterfaceIndex
	rcMplsLdpRouteNextHopAddrType	InetAddressType
	rcMplsLdpRouteNextHopAddr	InetAddress

RcMplsLdpSessionEntry
SEQUENCE
	rcMplsLdpSessionEntityLdpId	MplsLdpIdentifier
	rcMplsLdpSessionEntityIndex	IndexInteger
	rcMplsLdpSessionPeerLdpId	MplsLdpIdentifier
	rcMplsLdpSessionStateLastChange	Unsigned32
	rcMplsLdpSessionState	INTEGER
	rcMplsLdpSessionRole	INTEGER
	rcMplsLdpSessionProtocolVersion	Unsigned32
	rcMplsLdpSessionKeepAliveHoldTimeRem	Integer32
	rcMplsLdpSessionKeepAliveTime	Unsigned32
	rcMplsLdpSessionMaxPduLength	Unsigned32
	rcMplsLdpSessionDiscontinuityTime	Integer32
	rcMplsLdpSessionHoldTime	Unsigned32
	rcMplsLdpSessionUpTime	Integer32
	rcMplsLdpSessionMessagesSent	Counter32
	rcMplsLdpSessionMessagesRecv	Counter32

RcMplsLdpInterfaceEntry
SEQUENCE
	rcMplsLdpInterfaceIfIndex	InterfaceIndex
	rcMplsLdpInterfaceNbrCount	Unsigned32
	rcMplsLdpInterfaceNextHello	Unsigned32
	rcMplsLdpInterfaceConfHoldTime	Unsigned32
	rcMplsLdpInterfaceNegHoldTime	Unsigned32
	rcMplsLdpInterfaceHelloInterval	Unsigned32

RcMplsLdpStatsEntry
SEQUENCE
	rcMplsLdpStatsPeerAddress	IpAddress
	rcMplsLdpStatsNotifyRecv	Counter32
	rcMplsLdpStatsNotifySent	Counter32
	rcMplsLdpStatsHelloRecv	Counter32
	rcMplsLdpStatsHelloSent	Counter32
	rcMplsLdpStatsInitRecv	Counter32
	rcMplsLdpStatsInitSent	Counter32
	rcMplsLdpStatsKeepRecv	Counter32
	rcMplsLdpStatsKeepSent	Counter32
	rcMplsLdpStatsAddrRecv	Counter32
	rcMplsLdpStatsAddrSent	Counter32
	rcMplsLdpStatsAddrWdrRecv	Counter32
	rcMplsLdpStatsAddrWdrSent	Counter32
	rcMplsLdpStatsLabelMapRecv	Counter32
	rcMplsLdpStatsLabelMapSent	Counter32
	rcMplsLdpStatsLabelReqRecv	Counter32
	rcMplsLdpStatsLabelReqSent	Counter32
	rcMplsLdpStatsLabelWdrRecv	Counter32
	rcMplsLdpStatsLabelWdrSent	Counter32
	rcMplsLdpStatsLabelRelRecv	Counter32
	rcMplsLdpStatsLabelRelSent	Counter32
	rcMplsLdpStatsLabelAbrRecv	Counter32
	rcMplsLdpStatsLabelAbrSent	Counter32
	rcMplsLdpStatsSessionUp	Counter32
	rcMplsLdpStatsSessionDown	Counter32
	rcMplsLdpStatsBadLdpIdentifierErrors	Counter32
	rcMplsLdpStatsBadPduLengthErrors	Counter32
	rcMplsLdpStatsBadMessageLengthErrors	Counter32
	rcMplsLdpStatsUnknownMessageErrors	Counter32
	rcMplsLdpStatsUnknownTlvErrors	Counter32
	rcMplsLdpStatsBadTlvLengthErrors	Counter32
	rcMplsLdpStatsMalformedTlvValueErrors	Counter32
	rcMplsLdpStatsHoldTimerExpErrors	Counter32
	rcMplsLdpStatsSessionRejectedNoHelloErrors	Counter32
	rcMplsLdpStatsSessionRejectedBadParmAdvErrors	Counter32
	rcMplsLdpStatsSessionRejectedMaxPduErrors	Counter32
	rcMplsLdpStatsSessionRejectedBadLabelRangeErrors	Counter32
	rcMplsLdpStatsSessionRejectedSetupAbortErrors	Counter32
	rcMplsLdpStatsSessionRejectedBadKeepaliveErrors	Counter32
	rcMplsLdpStatsSessionOtherErrors	Counter32
	rcMplsLdpStatsClear	TruthValue

RcMsdpPeerEntry
SEQUENCE
	rcMsdpPeerAsNumber	Integer32
	rcMsdpPeerTooShortMessages	Counter32
	rcMsdpPeerInBadMessages	Counter32
	rcMsdpPeerInKeepAliveMessages	Counter32
	rcMsdpPeerOutKeepAliveMessages	Counter32
	rcMsdpPeerInSAFilterEnabled	TruthValue
	rcMsdpPeerInSAFilterRouteMapName	SnmpAdminString
	rcMsdpPeerOutSAFilterEnabled	TruthValue
	rcMsdpPeerOutSAFilterRouteMapName	SnmpAdminString
	rcMsdpPeerDescription	SnmpAdminString
	rcMsdpPeerSALimit	Unsigned32
	rcMsdpPeerMd5AuthEnabled	TruthValue
	rcMsdpPeerMd5AuthPassword	SnmpAdminString
	rcMsdpPeerSAsLearnedFromThisPeer	Counter32
	rcMsdpPeerSAsAdvertisedToThisPeer	Counter32
	rcMsdpPeerUpOrDownTime	TimeTicks
	rcMsdpPeerConnAndStatsClearedTime	TimeTicks
	rcMsdpPeerRouteMapName	SnmpAdminString
	rcMsdpPeerAdminEnabled	TruthValue
	rcMsdpPeerOperEnabled	TruthValue
	rcMsdpPeerDefaultPeerState	INTEGER
	rcMsdpPeerDefaultPeer	TruthValue

RcMsdpSACacheEntry
SEQUENCE
	rcMsdpSACacheGroupAddr	IpAddress
	rcMsdpSACacheSourceAddr	IpAddress
	rcMsdpSACacheOriginRP	IpAddress
	rcMsdpSACacheTypeInformation	INTEGER
	rcMsdpSACacheOriginatorAsNumber	Unsigned32
	rcMsdpSACacheRouteType	INTEGER

RcVrrpTmpOperationsEntry
SEQUENCE
	rcVrrpTmpOperationsIfIndex	InterfaceIndex
	rcVrrpTmpOperationsInetAddrType	InetAddressType
	rcVrrpTmpOperationsVrId	VrId
	rcVrrpTmpOperationsVirtualMacAddr	MacAddress
	rcVrrpTmpOperationsState	INTEGER
	rcVrrpTmpOperationsPriority	Integer32
	rcVrrpTmpOperationsAddrCount	Integer32
	rcVrrpTmpOperationsMasterIpAddr	InetAddress
	rcVrrpTmpOperationsPrimaryIpAddr	InetAddress
	rcVrrpTmpOperationsAdvInterval	TimeInterval
	rcVrrpTmpOperationsPreemptMode	TruthValue
	rcVrrpTmpOperationsAcceptMode	TruthValue
	rcVrrpTmpOperationsUpTime	TimeStamp
	rcVrrpTmpOperationsStorageType	StorageType
	rcVrrpTmpOperationsRowStatus	RowStatus

RcVrrpTmpAssociatedIpAddrEntry
SEQUENCE
	rcVrrpTmpAssociatedIpAddr	InetAddress
	rcVrrpTmpAssociatedIpAddrPrefixLength	InetAddressPrefixLength
	rcVrrpTmpAssociatedStorageType	StorageType
	rcVrrpTmpAssociatedIpAddrRowStatus	RowStatus

RcVrrpTmpRouterStatisticsEntry
SEQUENCE
	rcVrrpTmpStatisticsMasterTransitions	Counter32
	rcVrrpTmpStatisticsRcvdAdvertisements	Counter32
	rcVrrpTmpStatisticsAdvIntervalErrors	Counter32
	rcVrrpTmpStatisticsIpTtlErrors	Counter32
	rcVrrpTmpStatisticsRcvdPriZeroPackets	Counter32
	rcVrrpTmpStatisticsSentPriZeroPackets	Counter32
	rcVrrpTmpStatisticsRcvdInvalidTypePkts	Counter32
	rcVrrpTmpStatisticsAddressListErrors	Counter32
	rcVrrpTmpStatisticsPacketLengthErrors	Counter32
	rcVrrpTmpStatisticsRcvdInvalidAuthentications	Counter32
	rcVrrpTmpStatisticsDiscontinuityTime	TimeStamp
	rcVrrpTmpStatisticsRefreshRate	Integer32

RcVrrpExtOperationsEntry
SEQUENCE
	rcVrrpExtOperationsAction	INTEGER
	rcVrrpExtOperationsBackUpMaster	INTEGER
	rcVrrpExtOperationsBackUpMasterState	INTEGER
	rcVrrpExtOperationsCriticalIpAddr	InetAddress
	rcVrrpExtOperationsCriticalIpAddrEnabled	TruthValue
	rcVrrpExtOperationsControl	INTEGER
	rcVrrpExtOperationsHoldDownTimer	Integer32
	rcVrrpExtOperationsHoldDownState	INTEGER
	rcVrrpExtOperationsHoldDownTimeRemaining	Integer32
	rcVrrpExtOperationsFasterAdvInterval	Integer32
	rcVrrpExtOperationsFasterAdvIntervalEnabled	TruthValue
	rcVrrpExtOperationsLinkLocalAddr	InetAddress
	rcVrrpExtOperationsGlobalIpAddr	InetAddress

RcIsisCircuitEntry
SEQUENCE
	rcIsisCircuitIndex	Integer32
	rcIsisCircuitType	INTEGER
	rcIsisCircuitAuthType	INTEGER
	rcIsisCircuitKeyId	INTEGER
	rcIsisCircuitAuthKey	OCTET STRING
	rcIsisCircuitAddr	IpAddress
	rcIsisCircuitMask	IpAddress
	rcIsisCircuitOperState	INTEGER
	rcIsisCircuitNumAdj	Integer32
	rcIsisCircuitNumUpAdj	Integer32

RcIsisPlsbEntry
SEQUENCE
	rcIsisPlsbId	Integer32
	rcIsisPlsbRowStatus	RowStatus
	rcIsisPlsbNodeNickName	IsisPlsbNodeNickName
	rcIsisPlsbVlans	OCTET STRING	Size(512)
	rcIsisPlsbLsdbTrap	EnableValue
	rcIsisPlsbState	EnableValue
	rcIsisPlsbIpShortcut	EnableValue
	rcIsisPlsbPrimaryVlan	Integer32
	rcIsisPlsbSmltSplitBEB	INTEGER
	rcIsisPlsbSmltBmac	MacAddress
	rcIsisPlsbSmltPeerSysId	IsisSystemID

IsisDefaultL1Metric
Integer sub-range for default metric for single hop. ISO 10589 provides for 4 types of metric. Only the 'default' metric is used in practice.
TEXTUAL-CONVENTION
	Integer32	1..63

IsisWideL1Metric
Wide Metric for IS Neighbors. ISO 10589 provides a 6 bit metric. Traffic Engineering extensions provide 24 bit metrics.
TEXTUAL-CONVENTION
	Integer32	1..16777215

RcIsisCircuitPlsbEntry
SEQUENCE
	rcIsisCircuitPlsbIndex	Integer32
	rcIsisCircuitPlsbId	Integer32
	rcIsisCircuitPlsbRowStatus	RowStatus
	rcIsisCircuitPlsbState	EnableValue
	rcIsisCircuitPlsbType	INTEGER
	rcIsisCircuitPlsbL1Metric	IsisDefaultL1Metric
	rcIsisCircuitPlsbWideL1Metric	IsisWideL1Metric

RcIsisPlsbUnicastFibEntry
SEQUENCE
	rcIsisPlsbUnicastFibDestinationMacAddr	MacAddress
	rcIsisPlsbUnicastFibVlan	Integer32
	rcIsisPlsbUnicastFibSysId	OCTET STRING
	rcIsisPlsbUnicastFibOutgoingPort	InterfaceIndex

RcIsisPlsbMulticastFibEntry
SEQUENCE
	rcIsisPlsbMulticastFibMcastDestMacAddr	MacAddress
	rcIsisPlsbMulticastFibVlan	Integer32
	rcIsisPlsbMulticastFibSysId	OCTET STRING
	rcIsisPlsbMulticastFibIsid	Integer32
	rcIsisPlsbMulticastFibOutgoingPorts	DisplayString

RcIsisPlsbIsidEntry
SEQUENCE
	rcIsisPlsbIsidSourceName	Integer32
	rcIsisPlsbIsidId	Integer32
	rcIsisPlsbIsidSysId	OCTET STRING
	rcIsisPlsbIsidType	INTEGER

IsisPlsbBvid
ISIS B-VLAN ID.
TEXTUAL-CONVENTION
	Integer32	0..4096

IsisPlsbBvidTieBrkAlg
ISIS B-VLAN tie breaking algorithm.
TEXTUAL-CONVENTION
	INTEGER	low-pathid(1), high-pathid(2)

RcIsisAdjEntry
SEQUENCE
	rcIsisAdjCircIndex	Integer32
	rcIsisAdjIndex	Unsigned32
	rcIsisAdjHostName	OCTET STRING
	rcIsisAdjIfIndex	InterfaceIndex

RcIsisLSPEntry
SEQUENCE
	rcIsisLSPLevel	INTEGER
	rcIsisLSPID	OCTET STRING
	rcIsisLSPSeq	Unsigned32
	rcIsisLSPHostName	OCTET STRING
	rcIsisLSPNickName	Integer32
	rcIsisLSPLifetimeRemain	Unsigned32

RcIsisPlsbIpUnicastFibEntry
SEQUENCE
	rcIsisPlsbIpUnicastFibVrfId	Integer32
	rcIsisPlsbIpUnicastFibDestinationIpAddrType	InetAddressType
	rcIsisPlsbIpUnicastFibDestinationIpAddr	InetAddress
	rcIsisPlsbIpUnicastFibDestinationMask	InetAddressPrefixLength
	rcIsisPlsbIpUnicastFibNextHopBmac	MacAddress
	rcIsisPlsbIpUnicastFibVlan	Integer32
	rcIsisPlsbIpUnicastFibIsid	Integer32
	rcIsisPlsbIpUnicastFibNextHopName	DisplayString
	rcIsisPlsbIpUnicastFibOutgoingPort	InterfaceIndex
	rcIsisPlsbIpUnicastFibPrefixCost	Integer32
	rcIsisPlsbIpUnicastFibSpbmCost	Counter64

RcIsisPlsbUcastFibEntry
SEQUENCE
	rcIsisPlsbUcastFibSysId	OCTET STRING
	rcIsisPlsbUcastFibVlan	Integer32
	rcIsisPlsbUcastFibDestinationMacAddr	MacAddress
	rcIsisPlsbUcastFibOutgoingPort	InterfaceIndex
	rcIsisPlsbUcastFibHostName	OCTET STRING
	rcIsisPlsbUcastFibCost	Counter64

RcIsisPlsbMcastFibEntry
SEQUENCE
	rcIsisPlsbMcastFibSysId	OCTET STRING
	rcIsisPlsbMcastFibVlan	Integer32
	rcIsisPlsbMcastFibMcastDestMacAddr	MacAddress
	rcIsisPlsbMcastFibIsid	Integer32
	rcIsisPlsbMcastFibNickName	Integer32
	rcIsisPlsbMcastFibType	INTEGER
	rcIsisPlsbMcastFibOutgoingPorts	DisplayString
	rcIsisPlsbMcastFibHostName	OCTET STRING

RcIsisPlsbNodeEntry
SEQUENCE
	rcIsisPlsbNodeSysId	OCTET STRING
	rcIsisPlsbNodePrimaryParentSysId	OCTET STRING
	rcIsisPlsbNodePrimaryBvlan	Integer32
	rcIsisPlsbNodeSecondaryParentSysId	OCTET STRING
	rcIsisPlsbNodeSecondaryBvlan	Integer32

RcIsisSpbmPortDropStatsEntry
SEQUENCE
	rcIsisSpbmPortDropStatsPortIndex	InterfaceIndex
	rcIsisSpbmPortDropStatsVlanId	Integer32
	rcIsisSpbmPortDropStatsVlanType	INTEGER
	rcIsisSpbmPortDropStatsUnknownUcastSrcAddr	Counter64
	rcIsisSpbmPortDropStatsRpfcUcastSrcAddr	Counter64
	rcIsisSpbmPortDropStatsUnknownUcastDestAddr	Counter64
	rcIsisSpbmPortDropStatsUnknownMcastDestAddr	Counter64
	rcIsisSpbmPortDropStatsRpfcMcastSrcAddr	Counter64
	rcIsisSpbmPortDropStatsLastDropMac	MacAddress
	rcIsisSpbmPortDropStatsIsMacDestAddr	TruthValue
	rcIsisSpbmPortDropStatsLastDropMacHostName	OCTET STRING

RcCfmMaintenanceDomainEntry
SEQUENCE
	rcCfmMaintenanceDomainIndex	INTEGER
	rcCfmMaintenanceDomainName	DisplayString
	rcCfmMaintenanceDomainRowStatus	RowStatus
	rcCfmMaintenanceDomainNumOfMa	Integer32
	rcCfmMaintenanceDomainLevel	INTEGER
	rcCfmMaintenanceDomainNumOfMip	Integer32
	rcCfmMaintenanceDomainType	INTEGER

RcCfmMaintenanceAssociationEntry
SEQUENCE
	rcCfmMaintenanceAssociationDomainIndex	INTEGER
	rcCfmMaintenanceAssociationAssociationIndex	INTEGER
	rcCfmMaintenanceAssociationDomainName	DisplayString
	rcCfmMaintenanceAssociationAssociationName	DisplayString
	rcCfmMaintenanceAssociationAdminState	EnableValue
	rcCfmMaintenanceAssociationRowStatus	RowStatus
	rcCfmMaintenanceAssociationNumOfMep	Integer32

RcCfmMaintenanceEndPointEntry
SEQUENCE
	rcCfmMaintenanceEndPointDomainIndex	Integer32
	rcCfmMaintenanceEndPointAssociationIndex	Integer32
	rcCfmMaintenanceEndPointId	Integer32
	rcCfmMaintenanceEndPointDomainName	DisplayString
	rcCfmMaintenanceEndPointAssociationName	DisplayString
	rcCfmMaintenanceEndPointAdminState	EnableValue
	rcCfmMaintenanceEndPointRowStatus	RowStatus
	rcCfmMaintenanceEndPointMepType	INTEGER
	rcCfmMaintenanceEndPointServiceDescription	DisplayString
	rcCfmMaintenanceEndPointMepStatus	INTEGER

RcCfmTransmitLbmEntry
SEQUENCE
	rcCfmTransmitLbmDomainIndex	Integer32
	rcCfmTransmitLbmAssociationIndex	Integer32
	rcCfmTransmitLbmIndex	Integer32
	rcCfmTransmitLbmDomainName	DisplayString
	rcCfmTransmitLbmAssociationName	DisplayString
	rcCfmTransmitLbmDestMacAddress	MacAddress
	rcCfmTransmitLbmDestMepId	Integer32
	rcCfmTransmitLbmDestIsMepId	TruthValue
	rcCfmTransmitLbmMessages	Integer32
	rcCfmTransmitLbmVlanPriority	Integer32
	rcCfmTransmitLbmVlanDropEnable	TruthValue
	rcCfmTransmitLbmSeqNumber	Integer32
	rcCfmTransmitLbmResultOk	TruthValue
	rcCfmTransmitLbmStatus	INTEGER
	rcCfmTransmitLbmResult	DisplayString
	rcCfmTransmitLbmTimeoutInt	Integer32
	rcCfmTransmitLbmInterFrameInt	Integer32
	rcCfmTransmitLbmTestPattern	INTEGER
	rcCfmTransmitLbmDataSize	Integer32
	rcCfmTransmitLbmFrameSize	Integer32
	rcCfmTransmitLbmSourceMode	INTEGER

RcCfmTransmitLtmEntry
SEQUENCE
	rcCfmTransmitLtmDomainIndex	Integer32
	rcCfmTransmitLtmAssociationIndex	Integer32
	rcCfmTransmitLtmIndex	Integer32
	rcCfmTransmitLtmDomainName	DisplayString
	rcCfmTransmitLtmAssociationName	DisplayString
	rcCfmTransmitLtmVlanPriority	Integer32
	rcCfmTransmitLtmDestMacAddress	MacAddress
	rcCfmTransmitLtmDestMepId	Integer32
	rcCfmTransmitLtmDestIsMepId	TruthValue
	rcCfmTransmitLtmTtl	Integer32
	rcCfmTransmitLtmSeqNumber	Integer32
	rcCfmTransmitLtmResultOk	TruthValue
	rcCfmTransmitLtmStatus	INTEGER
	rcCfmTransmitLtmResult	DisplayString
	rcCfmTransmitLtmFlag	INTEGER
	rcCfmTransmitLtmSourceMode	INTEGER

CfmRelayActionFieldValue
Possible values the Relay action field can take.
TEXTUAL-CONVENTION
	INTEGER	rlyHit(1), rlyFdb(2), rlyMpdb(3), unknown(4)

CfmIngressActionFieldValue
Possible values returned in the ingress action field.
TEXTUAL-CONVENTION
	INTEGER	ingOk(1), ingDown(2), ingBlocked(3), ingVid(4), ingNoTlv(5)

CfmEgressActionFieldValue
Possible values returned in the egress action field
TEXTUAL-CONVENTION
	INTEGER	egrOk(1), egrDown(2), egrBlocked(3), egrVid(4), egrNoTlv(5)

LldpPortIdSubtype
This TC describes the source of a particular type of Port identifier used in the LLDP MIB. The enumeration 'interfaceAlias(1)' represents a port identifier based on the ifAlias MIB object, defined in IETF RFC 2863. The enumeration 'portComponent(2)' represents a port identifier based on the value of entPhysicalAlias (defined in IETF RFC 2737) for a port component (i.e., entPhysicalClass value of 'port(10)'), within the containing chassis. The enumeration 'macAddress(3)' represents a port identifier based on a unicast source address (encoded in network byte order and IEEE 802.3 canonical bit order), which has been detected by the agent and associated with a particular port (IEEE Std 802-2001). The enumeration 'networkAddress(4)' represents a port identifier based on a network address, detected by the agent and associated with a particular port. The enumeration 'interfaceName(5)' represents a port identifier based on the ifName MIB object, defined in IETF RFC 2863. The enumeration 'agentCircuitId(6)' represents a port identifier based on the agent-local identifier of the circuit (defined in RFC 3046), detected by the agent and associated with a particular port. The enumeration 'local(7)' represents a port identifier based on a value locally assigned.
TEXTUAL-CONVENTION
	INTEGER	interfaceAlias(1), portComponent(2), macAddress(3), networkAddress(4), interfaceName(5), agentCircuitId(6), local(7)

LldpPortId
This TC describes the format of a port identifier string. Objects of this type are always used with an associated LldpPortIdSubtype object, which identifies the format of the particular LldpPortId object instance. If the associated LldpPortIdSubtype object has a value of '342/200/230interfaceAlias(1)', then the octet string identifies a particular instance of the ifAlias object (defined in IETF RFC 2863). If the particular ifAlias object does not contain any values, another port identifier type should be used. If the associated LldpPortIdSubtype object has a value of 'portComponent(2)', then the octet string identifies a particular instance of the entPhysicalAlias object (defined in IETF RFC 2737) for a port or backplane component. If the associated LldpPortIdSubtype object has a value of 'macAddress(3)', then this string identifies a Particular unicast source address (encoded in network byte order and IEEE 802.3 canonical bit order) associated with the port (IEEE Std 802-2001). If the associated LldpPortIdSubtype object has a value of 'networkAddress(4)', then this string identifies a Network address associated with the port. The first octet contains the IANA AddressFamilyNumbers enumeration value for the specific address type, and octets 2 through N contain the networkAddress address value in network byte order. If the associated LldpPortIdSubtype object has a value of 'interfaceName(5)', then the octet string identifies A particular instance of the ifName object (defined in IETF RFC 2863). If the particular ifName object does not contain any values, another port identifier type should be used. If the associated ldpPortIdSubtype object has a value of 'agentCircuitId(6)', then this string identifies a agent-local identifier of the circuit (defined in RFC 3046). If the associated LldpPortIdSubtype object has a value of '342/200/230local(7)', then this string identifies a locally assigned port ID.
TEXTUAL-CONVENTION
	OCTET STRING	Size(1..255)

RcCfmLtrReplyEntry
SEQUENCE
	rcCfmLtrReplyDomainIndex	Integer32
	rcCfmLtrReplyAssociationIndex	Integer32
	rcCfmLtrReplyMepId	Integer32
	rcCfmLtrReplySeqNumber	Integer32
	rcCfmLtrReplyHop	Integer32
	rcCfmLtrReplyReceiveOrder	Integer32
	rcCfmLtrReplyTtl	Integer32
	rcCfmLtrReplyDomainName	DisplayString
	rcCfmLtrReplyAssociationName	DisplayString
	rcCfmLtrReplyForwarded	TruthValue
	rcCfmLtrReplyTerminalMep	TruthValue
	rcCfmLtrReplyLastEgressIdentifier	OCTET STRING
	rcCfmLtrReplyNextEgressIdentifier	OCTET STRING
	rcCfmLtrReplyRelayAction	CfmRelayActionFieldValue
	rcCfmLtrReplySrcMac	MacAddress
	rcCfmLtrReplyIngressAction	CfmIngressActionFieldValue
	rcCfmLtrReplyIngressMac	MacAddress
	rcCfmLtrReplyIngressPortIdSubtype	LldpPortIdSubtype
	rcCfmLtrReplyIngressPortId	LldpPortId
	rcCfmLtrReplyEgressAction	CfmEgressActionFieldValue
	rcCfmLtrReplyEgressMac	MacAddress
	rcCfmLtrReplyEgressPortIdSubtype	LldpPortIdSubtype
	rcCfmLtrReplyEgressPortId	LldpPortId

RcCfmTransmitL2PingEntry
SEQUENCE
	rcCfmTransmitL2PingVlanId	Integer32
	rcCfmTransmitL2PingDestMacAddress	MacAddress
	rcCfmTransmitL2PingHostName	OCTET STRING
	rcCfmTransmitL2PingDestIsHostName	TruthValue
	rcCfmTransmitL2PingMessages	Integer32
	rcCfmTransmitL2PingPriority	Integer32
	rcCfmTransmitL2PingTimeoutInt	Integer32
	rcCfmTransmitL2PingTestPattern	INTEGER
	rcCfmTransmitL2PingDataSize	Integer32
	rcCfmTransmitL2PingFrameSize	Integer32
	rcCfmTransmitL2PingSourceMode	INTEGER
	rcCfmTransmitL2PingSeqNumber	Integer32
	rcCfmTransmitL2PingResultOk	TruthValue
	rcCfmTransmitL2PingStatus	INTEGER
	rcCfmTransmitL2PingResult	DisplayString

RcCfmTransmitL2TraceEntry
SEQUENCE
	rcCfmTransmitL2TraceVlanId	Integer32
	rcCfmTransmitL2TracePriority	Integer32
	rcCfmTransmitL2TraceDestMacAddress	MacAddress
	rcCfmTransmitL2TraceHostName	OCTET STRING
	rcCfmTransmitL2TraceIsid	Integer32
	rcCfmTransmitL2TraceNickName	DisplayString
	rcCfmTransmitL2TraceDestIsHostName	TruthValue
	rcCfmTransmitL2TraceIsidTree	TruthValue
	rcCfmTransmitL2TraceTtl	Integer32
	rcCfmTransmitL2TraceSourceMode	INTEGER
	rcCfmTransmitL2TraceSeqNumber	Integer32
	rcCfmTransmitL2TraceResultOk	TruthValue
	rcCfmTransmitL2TraceStatus	INTEGER
	rcCfmTransmitL2TraceFlag	INTEGER

RcCfmL2TraceReplyEntry
SEQUENCE
	rcCfmL2TraceReplyVlanId	Integer32
	rcCfmL2TraceReplySeqNumber	Integer32
	rcCfmL2TraceReplyHop	Integer32
	rcCfmL2TraceReplyReceiveOrder	Integer32
	rcCfmL2TraceReplyTtl	Integer32
	rcCfmL2TraceReplySrcMac	MacAddress
	rcCfmL2TraceReplyHostName	OCTET STRING
	rcCfmL2TraceReplyLastSrcMac	MacAddress
	rcCfmL2TraceReplyLastHostName	OCTET STRING

RcCfmTransmitL2IpPingEntry
SEQUENCE
	rcCfmTransmitL2IpPingIpAddrType	InetAddressType
	rcCfmTransmitL2IpPingIpAddr	InetAddress
	rcCfmTransmitL2IpPingVrfId	Integer32
	rcCfmTransmitL2IpPingVrfName	DisplayString
	rcCfmTransmitL2IpPingMessages	Integer32
	rcCfmTransmitL2IpPingTimeoutInt	Integer32
	rcCfmTransmitL2IpPingTestPattern	INTEGER
	rcCfmTransmitL2IpPingDataSize	Integer32
	rcCfmTransmitL2IpPingStatus	INTEGER
	rcCfmTransmitL2IpPingResultOk	TruthValue
	rcCfmTransmitL2IpPingPathsFound	Integer32
	rcCfmTransmitL2IpPingRowStatus	RowStatus

RcCfmL2IpPingReplyEntry
SEQUENCE
	rcCfmL2IpPingReplyIpAddrType	InetAddressType
	rcCfmL2IpPingReplyIpAddr	InetAddress
	rcCfmL2IpPingReplySendOrder	Integer32
	rcCfmL2IpPingReplyVrfId	Integer32
	rcCfmL2IpPingReplyVlanId	Integer32
	rcCfmL2IpPingReplyDestMacAddress	MacAddress
	rcCfmL2IpPingReplyPortNum	InterfaceIndex
	rcCfmL2IpPingReplyDestHostName	OCTET STRING
	rcCfmL2IpPingReplySize	Integer32
	rcCfmL2IpPingReplyPktsTx	Integer32
	rcCfmL2IpPingReplyPktsRx	Integer32
	rcCfmL2IpPingReplyPercentLossWhole	Integer32
	rcCfmL2IpPingReplyPercentLossFract	Integer32
	rcCfmL2IpPingReplyMinRoundTrip	Integer32
	rcCfmL2IpPingReplyMaxRoundTrip	Integer32
	rcCfmL2IpPingReplyRttAvgWhole	Integer32
	rcCfmL2IpPingReplyRttAvgFract	Integer32
	rcCfmL2IpPingReplyFlag	INTEGER

RcCfmTransmitL2IpTraceEntry
SEQUENCE
	rcCfmTransmitL2IpTraceIpAddrType	InetAddressType
	rcCfmTransmitL2IpTraceIpAddr	InetAddress
	rcCfmTransmitL2IpTraceVrfId	Integer32
	rcCfmTransmitL2IpTraceVrfName	DisplayString
	rcCfmTransmitL2IpTraceTtl	Integer32
	rcCfmTransmitL2IpTraceStatus	INTEGER
	rcCfmTransmitL2IpTraceResultOk	TruthValue
	rcCfmTransmitL2IpTracePathsFound	Integer32
	rcCfmTransmitL2IpTraceRowStatus	RowStatus

RcCfmL2IpTraceReplyEntry
SEQUENCE
	rcCfmL2IpTraceReplyIpAddrType	InetAddressType
	rcCfmL2IpTraceReplyIpAddr	InetAddress
	rcCfmL2IpTraceReplySendOrder	Integer32
	rcCfmL2IpTraceReplyHop	Integer32
	rcCfmL2IpTraceReplyReceiveOrder	Integer32
	rcCfmL2IpTraceReplyTtl	Integer32
	rcCfmL2IpTraceReplyVrfId	Integer32
	rcCfmL2IpTraceReplyVlanId	Integer32
	rcCfmL2IpTraceReplyDestMacAddress	MacAddress
	rcCfmL2IpTraceReplyPortNum	InterfaceIndex
	rcCfmL2IpTraceReplySeqNumber	Integer32
	rcCfmL2IpTraceReplySrcMac	MacAddress
	rcCfmL2IpTraceReplyHostName	OCTET STRING
	rcCfmL2IpTraceReplyLastSrcMac	MacAddress
	rcCfmL2IpTraceReplyLastHostName	OCTET STRING
	rcCfmL2IpTraceReplyFlag	INTEGER

Defined Values

rapidCity		1.3.6.1.4.1.2272
Enterprise MIB for the Accelar product family.
MODULE-IDENTITY

internet		1.3.6.1
OBJECT IDENTIFIER

snmpV2		1.3.6.1.6
OBJECT IDENTIFIER

snmpModules		1.3.6.1.6.3
OBJECT IDENTIFIER

snmpMIB		1.3.6.1.6.3.1
OBJECT IDENTIFIER

snmpMIBObjects		1.3.6.1.6.3.1.1
OBJECT IDENTIFIER

snmpTraps		1.3.6.1.6.3.1.1.5
OBJECT IDENTIFIER

rcMgmt		1.3.6.1.4.1.2272.1
OBJECT IDENTIFIER

rcA1100		1.3.6.1.4.1.2272.2
OBJECT IDENTIFIER

rcA1250		1.3.6.1.4.1.2272.6
OBJECT IDENTIFIER

rcA1150		1.3.6.1.4.1.2272.7
OBJECT IDENTIFIER

rcA1200		1.3.6.1.4.1.2272.8
OBJECT IDENTIFIER

rcA1050		1.3.6.1.4.1.2272.9
OBJECT IDENTIFIER

rcA740		1.3.6.1.4.1.2272.20
OBJECT IDENTIFIER

rcA750		1.3.6.1.4.1.2272.21
OBJECT IDENTIFIER

rcA790		1.3.6.1.4.1.2272.22
OBJECT IDENTIFIER

rcA750S		1.3.6.1.4.1.2272.23
OBJECT IDENTIFIER

rcA8003		1.3.6.1.4.1.2272.280887555
OBJECT IDENTIFIER

rcA8006		1.3.6.1.4.1.2272.280887558
OBJECT IDENTIFIER

rcA8010		1.3.6.1.4.1.2272.280887562
OBJECT IDENTIFIER

rcA8010co		1.3.6.1.4.1.2272.1623064842
OBJECT IDENTIFIER

rcA8610		1.3.6.1.4.1.2272.30
OBJECT IDENTIFIER

rcA8606		1.3.6.1.4.1.2272.31
OBJECT IDENTIFIER

rcA8110		1.3.6.1.4.1.2272.32
OBJECT IDENTIFIER

rcA8106		1.3.6.1.4.1.2272.33
OBJECT IDENTIFIER

rcA8603		1.3.6.1.4.1.2272.34
OBJECT IDENTIFIER

rcA8103		1.3.6.1.4.1.2272.35
OBJECT IDENTIFIER

rcA8110co		1.3.6.1.4.1.2272.36
OBJECT IDENTIFIER

rcA8610co		1.3.6.1.4.1.2272.37
OBJECT IDENTIFIER

rcBayStack		1.3.6.1.4.1.2272.40
OBJECT IDENTIFIER

rcA1424		1.3.6.1.4.1.2272.42
OBJECT IDENTIFIER

rcA1648		1.3.6.1.4.1.2272.43
OBJECT IDENTIFIER

rcA1612		1.3.6.1.4.1.2272.44
OBJECT IDENTIFIER

rcA1624		1.3.6.1.4.1.2272.45
OBJECT IDENTIFIER

rcRBS2402		1.3.6.1.4.1.2272.46
OBJECT IDENTIFIER

rcAtr8310		1.3.6.1.4.1.2272.47
OBJECT IDENTIFIER

rcAtr8306		1.3.6.1.4.1.2272.48
OBJECT IDENTIFIER

rcAtr8010		1.3.6.1.4.1.2272.49
OBJECT IDENTIFIER

rcAtr8006		1.3.6.1.4.1.2272.50
OBJECT IDENTIFIER

rcA8603r		1.3.6.1.4.1.2272.55
OBJECT IDENTIFIER

rcERS8603r		1.3.6.1.4.1.2272.56
OBJECT IDENTIFIER

rcA8803r		1.3.6.1.4.1.2272.57
OBJECT IDENTIFIER

rcA8806		1.3.6.1.4.1.2272.58
OBJECT IDENTIFIER

rcA8810		1.3.6.1.4.1.2272.59
OBJECT IDENTIFIER

rcA8810co		1.3.6.1.4.1.2272.60
OBJECT IDENTIFIER

rcVSP9012		1.3.6.1.4.1.2272.201
OBJECT IDENTIFIER

rcSystem		1.3.6.1.4.1.2272.1.1
OBJECT IDENTIFIER

rcTftp		1.3.6.1.4.1.2272.1.2
OBJECT IDENTIFIER

rcVlan		1.3.6.1.4.1.2272.1.3
OBJECT IDENTIFIER

rcChassis		1.3.6.1.4.1.2272.1.4
OBJECT IDENTIFIER

rcMirror		1.3.6.1.4.1.2272.1.5
OBJECT IDENTIFIER

rcDipSwitch		1.3.6.1.4.1.2272.1.6
OBJECT IDENTIFIER

rcTblSize		1.3.6.1.4.1.2272.1.7
OBJECT IDENTIFIER

rcIp		1.3.6.1.4.1.2272.1.8
OBJECT IDENTIFIER

rcArp		1.3.6.1.4.1.2272.1.9
OBJECT IDENTIFIER

rcRip		1.3.6.1.4.1.2272.1.10
OBJECT IDENTIFIER

rcTest		1.3.6.1.4.1.2272.1.11
OBJECT IDENTIFIER

rcStat		1.3.6.1.4.1.2272.1.12
OBJECT IDENTIFIER

rcStg		1.3.6.1.4.1.2272.1.13
OBJECT IDENTIFIER

rcBridge		1.3.6.1.4.1.2272.1.14
OBJECT IDENTIFIER

rcBoot		1.3.6.1.4.1.2272.1.15
OBJECT IDENTIFIER

rcDevice		1.3.6.1.4.1.2272.1.16
OBJECT IDENTIFIER

rcMlt		1.3.6.1.4.1.2272.1.17
OBJECT IDENTIFIER

rcWeb		1.3.6.1.4.1.2272.1.18
OBJECT IDENTIFIER

rcCli		1.3.6.1.4.1.2272.1.19
OBJECT IDENTIFIER

rcError		1.3.6.1.4.1.2272.1.20
OBJECT IDENTIFIER

rcTraps		1.3.6.1.4.1.2272.1.21
OBJECT IDENTIFIER

rcSyslog		1.3.6.1.4.1.2272.1.22
OBJECT IDENTIFIER

rcDiag		1.3.6.1.4.1.2272.1.23
OBJECT IDENTIFIER

rcIpx		1.3.6.1.4.1.2272.1.24
OBJECT IDENTIFIER

rcPos		1.3.6.1.4.1.2272.1.26
OBJECT IDENTIFIER

rcLinkFlapDetect		1.3.6.1.4.1.2272.1.27
OBJECT IDENTIFIER

rcV1Traps		1.3.6.1.4.1.2272.1.28
OBJECT IDENTIFIER

rcRadius		1.3.6.1.4.1.2272.1.29
OBJECT IDENTIFIER

rcIgmp		1.3.6.1.4.1.2272.1.30
OBJECT IDENTIFIER

rcUserSetTime		1.3.6.1.4.1.2272.1.31
OBJECT IDENTIFIER

rcL2Redundancy		1.3.6.1.4.1.2272.1.32
OBJECT IDENTIFIER

rcNtp		1.3.6.1.4.1.2272.1.33
OBJECT IDENTIFIER

rcSsh		1.3.6.1.4.1.2272.1.34
OBJECT IDENTIFIER

rcSvlan		1.3.6.1.4.1.2272.1.35
OBJECT IDENTIFIER

rcOpm		1.3.6.1.4.1.2272.1.36
OBJECT IDENTIFIER

rcVpn		1.3.6.1.4.1.2272.1.37
OBJECT IDENTIFIER

rcOeAdm		1.3.6.1.4.1.2272.1.38
OBJECT IDENTIFIER

rcTlsVpn		1.3.6.1.4.1.2272.1.39
OBJECT IDENTIFIER

rcTls		1.3.6.1.4.1.2272.1.40
OBJECT IDENTIFIER

rcCos		1.3.6.1.4.1.2272.1.41
OBJECT IDENTIFIER

rcBanRing		1.3.6.1.4.1.2272.1.42
OBJECT IDENTIFIER

rcRing		1.3.6.1.4.1.2272.1.43
OBJECT IDENTIFIER

rcMmrp		1.3.6.1.4.1.2272.1.44
OBJECT IDENTIFIER

rcTengEnet		1.3.6.1.4.1.2272.1.50
OBJECT IDENTIFIER

rcRec		1.3.6.1.4.1.2272.1.51
OBJECT IDENTIFIER

rcTdc		1.3.6.1.4.1.2272.1.52
OBJECT IDENTIFIER

rcLacp		1.3.6.1.4.1.2272.1.53
OBJECT IDENTIFIER

rcQos		1.3.6.1.4.1.2272.1.54
OBJECT IDENTIFIER

rcFilter		1.3.6.1.4.1.2272.1.55
OBJECT IDENTIFIER

rcLicense		1.3.6.1.4.1.2272.1.56
OBJECT IDENTIFIER

rcEap		1.3.6.1.4.1.2272.1.57
OBJECT IDENTIFIER

rcMcast		1.3.6.1.4.1.2272.1.58
OBJECT IDENTIFIER

rcOspf		1.3.6.1.4.1.2272.1.59
OBJECT IDENTIFIER

rcFdb		1.3.6.1.4.1.2272.1.60
OBJECT IDENTIFIER

rcIgap		1.3.6.1.4.1.2272.1.61
OBJECT IDENTIFIER

rcIpv6		1.3.6.1.4.1.2272.1.62
OBJECT IDENTIFIER

rcIsis		1.3.6.1.4.1.2272.1.63
OBJECT IDENTIFIER

rcSlpp		1.3.6.1.4.1.2272.1.64
OBJECT IDENTIFIER

rcTacacs		1.3.6.1.4.1.2272.1.65
OBJECT IDENTIFIER

rcIpfix		1.3.6.1.4.1.2272.1.66
OBJECT IDENTIFIER

rcOspfv3		1.3.6.1.4.1.2272.1.67
OBJECT IDENTIFIER

rcFlowClassifier		1.3.6.1.4.1.2272.1.68
OBJECT IDENTIFIER

rcCfm		1.3.6.1.4.1.2272.1.69
OBJECT IDENTIFIER

rcPwe3		1.3.6.1.4.1.2272.1.70
OBJECT IDENTIFIER

rcPlugOptMod		1.3.6.1.4.1.2272.1.71
OBJECT IDENTIFIER

rc8021ah		1.3.6.1.4.1.2272.1.72
OBJECT IDENTIFIER

rcVrrp		1.3.6.1.4.1.2272.1.73
OBJECT IDENTIFIER

rcMpls		1.3.6.1.4.1.2272.1.74
OBJECT IDENTIFIER

rcPim		1.3.6.1.4.1.2272.1.75
OBJECT IDENTIFIER

rcIpMRoute		1.3.6.1.4.1.2272.1.76
OBJECT IDENTIFIER

rcCsu		1.3.6.1.4.1.2272.1.77
OBJECT IDENTIFIER

rcPlsb		1.3.6.1.4.1.2272.1.78
OBJECT IDENTIFIER

rcCoreDump		1.3.6.1.4.1.2272.1.79
OBJECT IDENTIFIER

rcMsdp		1.3.6.1.4.1.2272.1.80
OBJECT IDENTIFIER

rcBfd		1.3.6.1.4.1.2272.1.81
OBJECT IDENTIFIER

rcLinkOam		1.3.6.1.4.1.2272.1.82
OBJECT IDENTIFIER

rcAccessMstp		1.3.6.1.4.1.2272.1.83
OBJECT IDENTIFIER

rcDhu		1.3.6.1.4.1.2272.1.84
OBJECT IDENTIFIER

rcKhi		1.3.6.1.4.1.2272.1.85
OBJECT IDENTIFIER

rc2k		1.3.6.1.4.1.2272.1.100
OBJECT IDENTIFIER

rcOm8k		1.3.6.1.4.1.2272.1.200
OBJECT IDENTIFIER

cobra		1.3.6.1.4.1.2272.1.201
OBJECT IDENTIFIER

rcPowerRanger		1.3.6.1.4.1.2272.1.202
OBJECT IDENTIFIER

rcVrf		1.3.6.1.4.1.2272.1.203
OBJECT IDENTIFIER

rcCobaltBlue		1.3.6.1.4.1.2272.1.204
OBJECT IDENTIFIER

rcOlc		1.3.6.1.4.1.2272.1.205
OBJECT IDENTIFIER

rcVrrpv3		1.3.6.1.4.1.2272.1.206
OBJECT IDENTIFIER

rcPlsb		1.3.6.1.4.1.2272.1.78
OBJECT IDENTIFIER

rcSysIpAddr		1.3.6.1.4.1.2272.1.1.1
This entity's IP address.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcSysNetMask		1.3.6.1.4.1.2272.1.1.2
This entity's subnet mask.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcSysBroadcast		1.3.6.1.4.1.2272.1.1.3
This entity's broadcast address.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcSysCommReadWriteAll		1.3.6.1.4.1.2272.1.1.4
When an SNMP message is received by this entity, the community string in the message is compared with this string first. If it matches, read-write access is granted to all items in the MIB. If it doesn't match, the rcSysCommReadWrite string is compared next.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

rcSysCommReadWrite		1.3.6.1.4.1.2272.1.1.5
When an SNMP message is received by this entity, the community string in the message is compared with this string second. If it matches, read-write access is granted to all items in the MIB except community strings. (Community strings appear empty when read and return a no such name error when an attempt is made to write them.) If it doesn't match, the rcSysCommReadWriteLayer3 string is compared next.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

rcSysCommReadOnly		1.3.6.1.4.1.2272.1.1.6
When an SNMP message is received by this entity, the community string in the message is compared with this string third. If it matches, read-only access is granted to all items in the MIB except community strings. (Community strings appear empty when read.) If it doesn't match, no access is granted, no response is sent back to the SNMP requester, and SNMP traps are sent to the SNMP trap receiver(s) if configured.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

rcSysVersion		1.3.6.1.4.1.2272.1.1.7
Software version running on device
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

rcSysAction		1.3.6.1.4.1.2272.1.1.8
Initiate a system action.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), hardReset(2), softReset(3), saveToNVRAM(4), resetCounters(5), saveToStandbyNVRAM(6), cpuSwitchOver(7), checkSwInFlash(8), checkSwInPcmcia(9), resetConsole(10), resetModem(11), flushIpRouteTbl(12), saveRuntimeConfig(13), saveRuntimeConfigToSlave(14), saveBootConfig(15), saveSlaveBootConfig(16), resetIstStatCounters(17)

rcSysResult		1.3.6.1.4.1.2272.1.1.9
Result from the last system action.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), inProgress(2), success(3), fail(4), flashReadFailed(5), pcmciaReadFailed(6), crcCheckFailed(7), noStandbyCpu(8)

rcSysLastChange		1.3.6.1.4.1.2272.1.1.10
Last management initiated configuration change since sysUpTime.
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

rcSysLastVlanChange		1.3.6.1.4.1.2272.1.1.11
Last management initiated VLAN configuration change since sysUpTime.
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

rcSysLastStatisticsReset		1.3.6.1.4.1.2272.1.1.12
Last management initiated statistics reset since sysUpTime.
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

rcSysBufferUtil		1.3.6.1.4.1.2272.1.1.13
Buffer utilization as a percentage of the total amount of buffer space in the system. A high value indicates congestion.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..100

rcSysBufferUtilPeak		1.3.6.1.4.1.2272.1.1.14
The largest buffer utilization since sysUpTime
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..100

rcSysBufferUtilPeakTime		1.3.6.1.4.1.2272.1.1.15
Timestamp for rcSysPeakBandwidth
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

rcSysNVRamSize		1.3.6.1.4.1.2272.1.1.16
Total Non-volatile RAM in Kbytes
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcSysNVRamUsed		1.3.6.1.4.1.2272.1.1.17
Non-volatile RAM in use in Kbytes
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcSysLastSaveToNVRam		1.3.6.1.4.1.2272.1.1.18
SysUpTime of the last time when NVRAM was written to. This could be a save of the system configuration or via a file transfer of a configuration file.
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

rcSysLastSaveToStandbyNVRam		1.3.6.1.4.1.2272.1.1.19
SysUpTime of the last time when the standby NVRAM (on the back-up CPU board) was written to.
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

rcSysCpuUtil		1.3.6.1.4.1.2272.1.1.20
Percentage of CPU utilization
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcSysSwitchFabricUtil		1.3.6.1.4.1.2272.1.1.21
Percentage of Switching Fabric utilization
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcSysRmonMemSize		1.3.6.1.4.1.2272.1.1.22
Amount of RAM in bytes to allocate for RMON to use when rcSysRmonEnable is TRUE.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	250000..4000000

rcSysRmonEnable		1.3.6.1.4.1.2272.1.1.23
Control whether the RMON feature should be enabled. To enable the RMON feature, set this variable to true. The RMON agent in the device will get started immediately if the amount of memory specified by rcSysRmonMemSize is currently available in the device. To disable the RMON feature, set this variable to false, save the new setting to NVRAM, and reboot the device. After the device is rebooted the RMON agent will not be operational.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcSysRmonSaveConfig		1.3.6.1.4.1.2272.1.1.24
Control whether RMON configuration information should be saved to NVRAM so RMON settings can be automatically reinstalled after a system reboot. Setting rcSysRmonSaveConfig to true does not immediately save the configuration information. The save happens when the rcSysAction variable is set to 'saveToNVRAM(4)'. This option is only meaningful when the rcSysRmonEnable variable is set to true.
Status: deprecated	Access: read-write
OBJECT-TYPE
	TruthValue

rcSysRmonTrapOption		1.3.6.1.4.1.2272.1.1.25
Used to indicate whether RMON traps should be sent to only the owner of the RMON alarm (i.e., the manager that created the alarm entry) or all trap recipients in the system trap receiver table.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	toOwner(1), toAll(2)

rcSysSupportRouting		1.3.6.1.4.1.2272.1.1.26
Used to indicate whether routing is supported in this product.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcSysSupportWebServer		1.3.6.1.4.1.2272.1.1.27
Used to indicate whether WebServer is supported in this product.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcSysLastIpAddrChange		1.3.6.1.4.1.2272.1.1.28
Last management initiated IP address change since sysUpTime. Any addition or deletion of an IP address to a single routable port or a VLAN is time-stamped by this variable.
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

rcSysCommReadWriteLayer3		1.3.6.1.4.1.2272.1.1.29
When an SNMP message is received by this entity, the community string in the message is compared with this string third. If it matches, read-write access is granted to all Layer-3 items in the MIB except community strings. (Community strings appear empty when read and return a no such name error when an attempt is made to write them.) If it doesn't match, the rcSysCommReadWriteLayer2 string is compared next.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

rcSysCommReadWriteLayer2		1.3.6.1.4.1.2272.1.1.30
When an SNMP message is received by this entity, the community string in the message is compared with this string fourth. If it matches, read-write access is granted to all Layer-2 items in the MIB except community strings. (Community strings appear empty when read and return a no such name error when an attempt is made to write them.) If it doesn't match, the rcSysCommReadOnly string is compared next.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

rcSysAccessPolicyEnable		1.3.6.1.4.1.2272.1.1.31
Used to configure the system access policy feature. if 'true', the rcSysAccessPolicyTable is examined to determine which packets should be allowed or denied access to this device.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcSysDefaultRuntimeConfigFileName		1.3.6.1.4.1.2272.1.1.32
default config.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

rcSysDefaultBootConfigFileName		1.3.6.1.4.1.2272.1.1.33
default boot config.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

rcSysConfigFileName		1.3.6.1.4.1.2272.1.1.34
File name used in conjunction with rcSysAction. If rcSysAction is set to 'saveRuntimeConfig' or 'saveRuntimeConfigToSlave' then this file name will be used instead of the file name specified in rcSysDefaultRuntimeConfigFileName. If rcSysAction is set to 'saveBootConfig' or 'saveBootConfigToSlave' then this file name will be used insteaad of the file name specified in rcSysDefaultBootConfigFileName. If the file name is blank (i.e., nothing is entered) then the default file name will be used.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

rcSysLastRunTimeConfigSave		1.3.6.1.4.1.2272.1.1.35
SysUpTime of the last time when the run time configuration was written to.
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

rcSysLastRunTimeConfigSaveToSlave		1.3.6.1.4.1.2272.1.1.36
SysUpTime of the last time when the run time configuration was written to slave NVRAM.
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

rcSysLastBootConfigSave		1.3.6.1.4.1.2272.1.1.37
SysUpTime of the last time when the boot configuration was written to.
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

rcSysLastBootConfigSaveOnSlave		1.3.6.1.4.1.2272.1.1.38
SysUpTime of the last time when the boot configuration was written on the slave NVRAM.
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

rcSysRmonUtilizationMethod		1.3.6.1.4.1.2272.1.1.39
Used to control whether RMON should use a half-duplex or full-duplex formula to calculate port utilization. When set to 'halfDuplex', RMON will use InOctets and the port's speed to calculate port utilization (this is the standard RMON rfc1271 convention). When set to 'fullDuplex', RMON will use InOctets and OutOctets and 2X the port's speed to calculate port utilization. Furthermore, if this variable is set to 'fullDuplex', but the port is operating in a half-duplex mode, the calculation defaults back to the rfc1271 convention.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	halfDuplex(1), fullDuplex(2)

rcSysCommReadWriteLayer1		1.3.6.1.4.1.2272.1.1.40
read-write L1 access
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

rcSysOtherBufferUtil		1.3.6.1.4.1.2272.1.1.41
bw currently consumed
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcSysOtherBufferUtilPeak		1.3.6.1.4.1.2272.1.1.42
peak bw since reset
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcSysOtherBufferUtilPeakTime		1.3.6.1.4.1.2272.1.1.43
timestamp for rcSysPeakBw
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

rcSysOtherCpuUtil		1.3.6.1.4.1.2272.1.1.44
% cpu utilization
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcSysOtherSwitchFabricUtil		1.3.6.1.4.1.2272.1.1.45
% switch fabric util
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcSysDramSize		1.3.6.1.4.1.2272.1.1.46
Dram size in mega-bytes
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcSysDramUsed		1.3.6.1.4.1.2272.1.1.47
Dram used in percentage
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcSysDramFree		1.3.6.1.4.1.2272.1.1.48
Dram free size in kilo-bytes
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcSysDramMaxBlockFree		1.3.6.1.4.1.2272.1.1.49
Dram max block free size in kilo-bytes
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcSysVirtualIpAddr		1.3.6.1.4.1.2272.1.1.51
Virtual IP is an IP address that owned and advertised only by the master CPU. So whichever CPU is master registers this IP address. Unlike the management IP address, this address goes in the switch config file and not the boot config
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcSysVirtualNetMask		1.3.6.1.4.1.2272.1.1.52
Net mask of the management virtual Ip address
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcSysReadWriteLevel		1.3.6.1.4.1.2272.1.1.53
The status of the read/write level
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcSysMTUSize		1.3.6.1.4.1.2272.1.1.55
This is the maximum transmission size of frames that all the ports on the chassis support.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	mtu1950(1), mtu9600(2), mtu1522(3)

rcSysClockSyncTime		1.3.6.1.4.1.2272.1.1.56
Time interval at which RTC and system clocks are synchronized.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	15..3600

rcSysForceTrapSender		1.3.6.1.4.1.2272.1.1.57
This is a flag that if user wants to configured CLIP (Circuit Less IP) as trap originator.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcSysMrouteStrLimit		1.3.6.1.4.1.2272.1.1.58
enable or disable mroute stream limit in system.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcSysTrapRecvTable		1.3.6.1.4.1.2272.1.1.60
The trap receiver table (0 to 25 entries). This table lists the addresses of Network Management Stations that should receive trap messages from this entity when an exception condition occurs.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcSysTrapRecvEntry

rcSysTrapRecvEntry		1.3.6.1.4.1.2272.1.1.60.1
A trap receiver table entry.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	RcSysTrapRecvEntry

rcSysTrapRecvAddress		1.3.6.1.4.1.2272.1.1.60.1.1
IP address for trap receiver.
Status: deprecated	Access: read-only
OBJECT-TYPE
	IpAddress

rcSysTrapRecvVersion		1.3.6.1.4.1.2272.1.1.60.1.2
The version of trap receiver.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	v1(1), v2c(2)

rcSysTrapRecvCommunity		1.3.6.1.4.1.2272.1.1.60.1.3
Community string used for trap messages to this trap receiver.
Status: deprecated	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

rcSysTrapRecvSrcAddress		1.3.6.1.4.1.2272.1.1.60.1.4
Source IP address to use when sending traps. This IP address will be inserted into the source IP address field in the UDP trap packet.
Status: deprecated	Access: read-write
OBJECT-TYPE
	IpAddress

rcSysTrapRecvRowStatus		1.3.6.1.4.1.2272.1.1.60.1.5
Used to create/delete entries
Status: deprecated	Access: read-write
OBJECT-TYPE
	RowStatus

rcSysAccessPolicyTable		1.3.6.1.4.1.2272.1.1.61
Management access policy table. This table is used to permit or deny access to this device via the specified source Id.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcSysAccesspolicyEntry

rcSysAccessPolicyEntry		1.3.6.1.4.1.2272.1.1.61.1
An access policy table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcSysAccesspolicyEntry

rcSysAccessPolicyId		1.3.6.1.4.1.2272.1.1.61.1.1
Policy Id.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

rcSysAccessPolicyName		1.3.6.1.4.1.2272.1.1.61.1.2
Name of this policy.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..15)

rcSysAccessPolicyPolicyEnable		1.3.6.1.4.1.2272.1.1.61.1.3
Indicate whether this policy is currently active.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcSysAccessPolicyMode		1.3.6.1.4.1.2272.1.1.61.1.4
Used to indicate whether a packet having a source IP address that matches this entry should be permitted to enter the device or denied access.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	allow(1), deny(2)

rcSysAccessPolicyService		1.3.6.1.4.1.2272.1.1.61.1.5
Is represented as bitset to indicate which protocol this entry should be applied to. Value is one of multiple(logical 'OR') of the following values: telnet(1), snmp(2), tftp(4), ftp(8), http(16), rlogin(32), ssh(64), snmp-v3(128) telnet(1): enables telnet service snmp(2): enables snmp service tftp(4): enables tftp service ftp(8): enables ftp service http(16): enables http service rlogin(32): enables rlogin service ssh(64): enables ssh service snmp-v3(128): enables snmp service for v3 groups Value 0 means no service enabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

rcSysAccessPolicyPrecedence		1.3.6.1.4.1.2272.1.1.61.1.6
Used to indicate the precedence of this policy. The Lower the number the higher the precedence.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..128

rcSysAccessPolicyNetAddr		1.3.6.1.4.1.2272.1.1.61.1.7
Source network IP address.
Status: deprecated	Access: read-write
OBJECT-TYPE
	IpAddress

rcSysAccessPolicyNetMask		1.3.6.1.4.1.2272.1.1.61.1.8
Source network mask.
Status: deprecated	Access: read-write
OBJECT-TYPE
	IpAddress

rcSysAccessPolicyTrustedHostAddr		1.3.6.1.4.1.2272.1.1.61.1.9
Trusted IP address of host performing a rlogin into the device.
Status: deprecated	Access: read-write
OBJECT-TYPE
	IpAddress

rcSysAccessPolicyTrustedHostUserName		1.3.6.1.4.1.2272.1.1.61.1.10
User name on the trusted host performing a rlogin into the device.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..30)

rcSysAccessPolicyAccessLevel		1.3.6.1.4.1.2272.1.1.61.1.11
Access level of trusted host.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	readOnly(1), readWrite(2), readWriteAll(3)

rcSysAccessPolicyLog		1.3.6.1.4.1.2272.1.1.61.1.12
Used to indicate whether logging should be performed if this policy was applied.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcSysAccessPolicyUsage		1.3.6.1.4.1.2272.1.1.61.1.13
Usage Counter
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcSysAccessPolicyRowStatus		1.3.6.1.4.1.2272.1.1.61.1.14
Used to create/delete an entry
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcSysAccessPolicyAccessStrict		1.3.6.1.4.1.2272.1.1.61.1.15
Used to restrict the access level specified in the system access policy table to exactly the same access level as specified by user. If TRUE then only the access level in the policy table is allowed access. If FALSE, then the default behavior is to assume the access level specified in policy table as the floor.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcSysAccessPolicyNetInetAddrType		1.3.6.1.4.1.2272.1.1.61.1.16
Source network Inet Address Type.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	any(0), ipv4(1), ipv6(2)

rcSysAccessPolicyNetInetAddress		1.3.6.1.4.1.2272.1.1.61.1.17
Source network Inet Address (prefix/network).
Status: current	Access: read-write
OBJECT-TYPE
	InetAddress

rcSysAccessPolicyNetInetAddrPrefixLen		1.3.6.1.4.1.2272.1.1.61.1.18
Source network Inet Address Prefix-Length/Mask.
Status: current	Access: read-write
OBJECT-TYPE
	InetAddressPrefixLength

rcSysAccessPolicyTrustedHostInetAddress		1.3.6.1.4.1.2272.1.1.61.1.19
Trusted Inet address of host performing a rlogin into the device.
Status: current	Access: read-write
OBJECT-TYPE
	InetAddress

rcSysAccPolSnmpGrpTable		1.3.6.1.4.1.2272.1.1.95
SNMP group list for access policy
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcSysAccPolSnmpGrpEntry

rcSysAccPolSnmpGrpEntry		1.3.6.1.4.1.2272.1.1.95.1
The table entry which covers the groups under snmp service.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcSysAccPolSnmpGrpEntry

rcSysAccPolSnmpGrpName		1.3.6.1.4.1.2272.1.1.95.1.1
The snmp-v3 group name
Status: current	Access: not-accessible
OBJECT-TYPE
	SnmpAdminString	Size(1..32)

rcSysAccPolSnmpGrpModel		1.3.6.1.4.1.2272.1.1.95.1.2
The snmp model
Status: current	Access: not-accessible
OBJECT-TYPE
	SnmpSecurityModel

rcSysAccPolSnmpGrpRowStatus		1.3.6.1.4.1.2272.1.1.95.1.3
Row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcSysTrapSenderTable		1.3.6.1.4.1.2272.1.1.62
The trap sender table (0 to 25 entries). This table lists the addresses of Network Management Stations and the Source Address that should receive trap messages from this entity when an exception condition occurs.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcSysTrapSenderEntry

rcSysTrapSenderEntry		1.3.6.1.4.1.2272.1.1.62.1
A trap sender table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcSysTrapSenderEntry

rcSysTrapSenderRecvAddress		1.3.6.1.4.1.2272.1.1.62.1.1
IP address for trap receiver.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcSysTrapSenderSrcAddress		1.3.6.1.4.1.2272.1.1.62.1.2
IP address for trap sender.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcSysDnsServerListTable		1.3.6.1.4.1.2272.1.1.64
DNS serever list table used to store the details of the DNS server configured.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcSysDnsServerListEntry

rcSysDnsServerListEntry		1.3.6.1.4.1.2272.1.1.64.1
table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcSysDnsServerListEntry

rcSysDnsServerListType		1.3.6.1.4.1.2272.1.1.64.1.1
Type of the DNS server
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	primary(0), secondary(1), tertiary(2)

rcSysDnsServerListIp		1.3.6.1.4.1.2272.1.1.64.1.2
IP address of the DNS server
Status: deprecated	Access: read-write
OBJECT-TYPE
	IpAddress

rcSysDnsServerListStatus		1.3.6.1.4.1.2272.1.1.64.1.3
Status of DNS server
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	active(0), in-active(1)

rcSysDnsServerListRequestCount		1.3.6.1.4.1.2272.1.1.64.1.4
Number of request send to this server
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcSysDnsServerListSuccessCount		1.3.6.1.4.1.2272.1.1.64.1.5
Number of request send to this server which are successful
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcSysDnsServerListRowStatus		1.3.6.1.4.1.2272.1.1.64.1.6
Used to create/delete DNS server entries in rcSysDnsServerListTable.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcSysDnsServerListAddressType		1.3.6.1.4.1.2272.1.1.64.1.7
The address type of DNS Server.
Status: current	Access: read-write
OBJECT-TYPE
	InetAddressType

rcSysDnsServerListAddress		1.3.6.1.4.1.2272.1.1.64.1.8
The address of the DNS Server
Status: current	Access: read-write
OBJECT-TYPE
	InetAddress

rcSysDnsHostTable		1.3.6.1.4.1.2272.1.1.65
DNS Host table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcSysDnsHostEntry

rcSysDnsHostEntry		1.3.6.1.4.1.2272.1.1.65.1
table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcSysDnsHostEntry

rcSysDnsHostData		1.3.6.1.4.1.2272.1.1.65.1.1
Host Name or Host IP Address.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..256)

rcSysDnsHostName		1.3.6.1.4.1.2272.1.1.65.1.2
Host Name.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..256)

rcSysDnsHostIpAddress		1.3.6.1.4.1.2272.1.1.65.1.3
Host IP Address.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcSysDnsHostSource		1.3.6.1.4.1.2272.1.1.65.1.4
DNS Server IP or /etc/host file.
Status: deprecated	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..256)

rcSysDnsHostAddressType		1.3.6.1.4.1.2272.1.1.65.1.5
Address Type of the Host.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddressType

rcSysDnsHostAddress		1.3.6.1.4.1.2272.1.1.65.1.6
Address of the Host.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddress

rcSysMsgLogFrequency		1.3.6.1.4.1.2272.1.1.66
Used to specify the maximum frequency/count of the occurence of the Log Message.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	2..500

rcSysMsgLogText		1.3.6.1.4.1.2272.1.1.67
A textual string containing the first four characters of the Log Message.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..3)

rcSysForceIpHdrSender		1.3.6.1.4.1.2272.1.1.68
Flag to decide if IP header source address will be matched with SNMP header sender networks.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcSysDnsDomainName		1.3.6.1.4.1.2272.1.1.70
Default domain used for querying the DNS Server.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

rcSysDnsServerListIpAddr		1.3.6.1.4.1.2272.1.1.71
DNS server's IP address
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcSysDnsRequestType		1.3.6.1.4.1.2272.1.1.72
DNS Type: Whether it was Dns Request or a Response
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	request(0), response(1)

rcSysSpanningTreeOperMode		1.3.6.1.4.1.2272.1.1.73
This object indicates the current spanning-tree mode of the system. The meaning of specific values is: nortelStpg(1) .. The older proprietary mode which supports multiple spanning tree groups. pvst(2) ..Emulation of C***O spanning tree mode rstp(3) ..IEEE 802.1w mode mstp(4) ..IEEE 802.1s mode .
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	nortelStpg(1), pvst(2), rstp(3), mstp(4)

rcSysSpanningTreeAdminMode		1.3.6.1.4.1.2272.1.1.74
This object indicates the desired spanning-tree mode of the system. The meaning of specific values is: nortelStpg(1) .. The older proprietary mode which supports multiple spanning tree groups. pvst(2) ..Emulation of C***O spanning tree mode rstp(3) ..IEEE 802.1w mode mstp(4) ..IEEE 802.1s mode . Note that depending on the current value of rcSysSpanningTreeOperMode and the value to which this object is set, the operational mode may be immediately changed, or the change may not take effect until the next system reboot.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nortelStpg(1), pvst(2), rstp(3), mstp(4)

rcSysAutoRecoverDelay		1.3.6.1.4.1.2272.1.1.75
Time interval in seconds after which auto-recovery runs on ports to clear action taken by cp-limit, link flap or loop detect
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	5..3600

rcSysMacFlapLimitTime		1.3.6.1.4.1.2272.1.1.76
Time limit in milliseconds for MAC flapping for loop-detect feature
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	10..5000

rcSysMacFlapLimitCount		1.3.6.1.4.1.2272.1.1.77
Number of times mac flapping can happen for loop-detect feature
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcSysExtCplimitEnable		1.3.6.1.4.1.2272.1.1.78
enable or disable extended CP-LIMIT in system.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcSysExtCplimitMinCongTime		1.3.6.1.4.1.2272.1.1.79
Minimum time for which System octapid should be congested to trigger congestion algorithm for extended CP-LIMIT in mSecs
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	100..6000

rcSysExtCplimitMaxPorts		1.3.6.1.4.1.2272.1.1.80
Maximum number of ports which need to be monitored for congestion in Extended CP-LIMIT
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..512

rcSysExtCplimitPortCongTime		1.3.6.1.4.1.2272.1.1.81
Minimum time for which ingress traffic utilization rate of a monitored port should stay more than the allowed limits in order to disable the port for extended CP-LIMIT in Secs
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..600

rcSysExtCplimitTrapLevel		1.3.6.1.4.1.2272.1.1.82
Indicates the trap level for extended CP-LIMIT
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), normal(2), verbose(3)

rcSysExtCplimitSysOctapidCongested		1.3.6.1.4.1.2272.1.1.83
Indicates whether system octapid congestion detected for extended cp-limit
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcSysExtCplimitPortsMonitored		1.3.6.1.4.1.2272.1.1.84
Indicates whether ports has been shutdown due to extended cp-limit
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcSysExtCplimitPortsShutDown		1.3.6.1.4.1.2272.1.1.85
Indicates whether ports has been shutdown due to extended Cp-limit
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcSysActionL1		1.3.6.1.4.1.2272.1.1.86
Initiate a system action for layer1 user
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), resetCounters(2), saveToNVRAM(3), saveToStandbyNVRAM(4), checkSwInFlash(5), checkSwInPcmcia(6), saveRuntimeConfig(7), saveRuntimeConfigToSlave(8), saveBootConfig(9), saveSlaveBootConfig(10), loadLicense(11)

rcSysActionL2		1.3.6.1.4.1.2272.1.1.87
Initiate a system action for layer2 user
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), resetIstStatCounters(2)

rcSysActionL3		1.3.6.1.4.1.2272.1.1.88
Initiate a system action for layer3 user
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), flushIpRouteTbl(2)

rcSysActionRwa		1.3.6.1.4.1.2272.1.1.89
Initiate a system action.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), hardReset(2), softReset(3), cpuSwitchOver(4), resetConsole(5), resetModem(6)

rcSysPowerUsage		1.3.6.1.4.1.2272.1.1.90
The current power usage for the whole chassis.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcSysPowerAvailable		1.3.6.1.4.1.2272.1.1.91
The current power available for the whole chassis.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcSysFrcMsgControlTable		1.3.6.1.4.1.2272.1.1.94
Management Force-msg Control table. This table is used to specify the pattern for Force-msg Control
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcSysFrcMsgControlEntry

rcSysVirtualIpv6Addr		1.3.6.1.4.1.2272.1.1.96
Virtual IP is an IP address that owned and advertised only by the master CPU. So whichever CPU is master registers this IP address.
Status: current	Access: read-write
OBJECT-TYPE
	Ipv6Address

rcSysVirtualIpv6PrefixLength		1.3.6.1.4.1.2272.1.1.97
The length of the virtual ipv6 addr prefix (in bits).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..128

rcSysConfigMode		1.3.6.1.4.1.2272.1.1.98
This is used in conjunction with rcSysAction inorder to decide the mode in which the config file is going to be saved in.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nncli(1), cli(2)

rcSysLicenseTrialDaysLeft		1.3.6.1.4.1.2272.1.1.100
This indicates days left before License Trial Period will expire.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..60

rcSysFrcMsgControlEntry		1.3.6.1.4.1.2272.1.1.94.1
A Force-msg Control table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcSysFrcMsgControlEntry

rcSysFrcMsgControlPatternId		1.3.6.1.4.1.2272.1.1.94.1.1
Pattern Id.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..32

rcSysFrcMsgControlPattern		1.3.6.1.4.1.2272.1.1.94.1.2
Pattern for filtering the force-msg for msg control
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(4)

rcSysFrcMsgControlRowStatus		1.3.6.1.4.1.2272.1.1.94.1.3
Used to create/delete an entry
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcTftpHost		1.3.6.1.4.1.2272.1.2.1
Name of source/destination host for the TFTP transfer.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcTftpFile		1.3.6.1.4.1.2272.1.2.2
Name of file for the TFTP transfer.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

rcTftpAction		1.3.6.1.4.1.2272.1.2.3
The action for the TFTP transfer.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), downloadConfig(2), uploadConfig(3), downloadSwToFlash(4), downloadSwToPcmcia(5), uploadSw(6), downloadSwToDram(7)

rcTftpResult		1.3.6.1.4.1.2272.1.2.4
Contains result of the last Tftp action request.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), inProgress(2), noResponse(3), fileAccessError(4), badFlash(5), flashEraseFailed(6), pcmciaEraseFailed(7), success(8), fail(9), writeToNvramFailed(10), flashWriteFailed(11), pcmciaWriteFailed(12), configFileTooBig(13), imageFileTooBig(14), noPcmciaDetect(15), pcmciaNotSupported(16), invalidFile(17), noMemory(18), xferError(19), crcError(20), readNvramFailed(21), pcmciaWriteProtect(22)

rcVlanNumVlans		1.3.6.1.4.1.2272.1.3.1
The number of VLANs currently defined in the switch.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..128

rcVlanTable		1.3.6.1.4.1.2272.1.3.2
A list of Virtual LAN entries. The number of entries is given by rcVlanNumVlans.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcVlanEntry

rcVlanEntry		1.3.6.1.4.1.2272.1.3.2.1
Entry containing configuration information for a particular Virtual LAN. The relationship between the various port sets in a VLAN Entry are : o The set of ports defined by PortMembers must be a subset of the set of ports in the underlying STG of the VLAN. o The bitwise AND of PortMembers and NotAllowToJoin must be the empty set. o The bitwise OR of PortMembers and NotAllowToJoin must be the set of ports in the underlying STG of the VLAN. o The set of ports defined by StaticMembers must be a subset of the set of ports defined by PortMembers. o The bitwise XOR of PortMembers and StaticMembers defines the set of dynamic (potential) members of the VLAN. o The set of ports defined by ActiveMembers must be a subset of the set of ports defined by PortMembers.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcVlanEntry

rcVlanId		1.3.6.1.4.1.2272.1.3.2.1.1
A value that uniquely identifies the Virtual LAN associated with this entry. This value corresponds to the lower 12 bits in the IEEE 802.1Q VLAN Tag.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4094

rcVlanName		1.3.6.1.4.1.2272.1.3.2.1.2
An administratively-assigned name for this VLAN.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..64)

rcVlanColor		1.3.6.1.4.1.2272.1.3.2.1.3
An administratively-assigned color code for this VLAN. The value of this object is used by the VLAN Manager GUI tool to select a color when it draws this VLAN on the screen.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..32

rcVlanHighPriority		1.3.6.1.4.1.2272.1.3.2.1.4
A flag to note whether frames in this VLAN should be assigned a high switching priority.
Status: deprecated	Access: read-write
OBJECT-TYPE
	TruthValue

rcVlanRoutingEnable		1.3.6.1.4.1.2272.1.3.2.1.5
A flag to note whether IP routing is enabled in this VLAN.
Status: deprecated	Access: read-write
OBJECT-TYPE
	TruthValue

rcVlanIfIndex		1.3.6.1.4.1.2272.1.3.2.1.6
When rcVlanRoutingEnable is set to true(1), this value indicates the 'logical' ifIndex assigned to this VLAN. Otherwise, this value is meaningless and should be set to zero.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcVlanAction		1.3.6.1.4.1.2272.1.3.2.1.7
VLAN related actions.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), flushMacFdb(2), flushArp(3), flushIp(4), flushDynMemb(5), all(6), flushSnoopMemb(7), triggerRipUpdate(8), flushSnoopMRtr(9)

rcVlanResult		1.3.6.1.4.1.2272.1.3.2.1.8
The result from the last VLAN action.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), inProgress(2), success(3), fail(4)

rcVlanStgId		1.3.6.1.4.1.2272.1.3.2.1.9
Indicates the Spanning Tree Group (STG) used by this VLAN to determine the state of its ports. If this VLAN is not associated with any STG, this value should be set to zero.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..128

rcVlanType		1.3.6.1.4.1.2272.1.3.2.1.10
The type of VLAN, distinguished according to the policy used to define its port membership.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	byPort(1), byIpSubnet(2), byProtocolId(3), bySrcMac(4), byDstMcast(5), bySvlan(6), byIds(7), spbm-bvlan(11)

rcVlanPortMembers		1.3.6.1.4.1.2272.1.3.2.1.11
The set of ports that are members (static or dynamic) of this VLAN.
Status: current	Access: read-write
OBJECT-TYPE
	PortSet

rcVlanActiveMembers		1.3.6.1.4.1.2272.1.3.2.1.12
The set of ports that are currently active in this VLAN. Active ports include all static ports and any dynamic ports where the VLAN policy was met.
Status: current	Access: read-only
OBJECT-TYPE
	PortSet

rcVlanStaticMembers		1.3.6.1.4.1.2272.1.3.2.1.13
The set of ports that are static members of this VLAN. A static member of a VLAN is always active and is never aged out.
Status: current	Access: read-write
OBJECT-TYPE
	PortSet

rcVlanNotAllowToJoin		1.3.6.1.4.1.2272.1.3.2.1.14
The set of ports that are not allowed to become members of this VLAN.
Status: current	Access: read-write
OBJECT-TYPE
	PortSet

rcVlanProtocolId		1.3.6.1.4.1.2272.1.3.2.1.15
The protocol identifier of this VLAN. This value is meaningful only if rcVlanType is equal to byProtocolId(3). For other VLAN types it should have the value none(0).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), ip(1), ipx802dot3(2), ipx802dot2(3), ipxSnap(4), ipxEthernet2(5), appleTalk(6), decLat(7), decOther(8), sna802dot2(9), snaEthernet2(10), netBios(11), xns(12), vines(13), ipV6(14), usrDefined(15), rarp(16), pPPoE(17)

rcVlanSubnetAddr		1.3.6.1.4.1.2272.1.3.2.1.16
The IP subnet address of this VLAN. This value is meaningful only if rcVlanType is equal to byIpSubnet(2). For other VLAN types it should have the value 0.0.0.0.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcVlanSubnetMask		1.3.6.1.4.1.2272.1.3.2.1.17
The IP subnet mask of this VLAN. This value is meaningful only if rcVlanType is equal to byIpSubnet(2). For other VLAN types it should have the value 0.0.0.0.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcVlanAgingTime		1.3.6.1.4.1.2272.1.3.2.1.18
The timeout period (in seconds) used for aging out dynamic members of this VLAN. This field is only relevant for policy-based VLANs.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0 | 10..1000000

rcVlanMacAddress		1.3.6.1.4.1.2272.1.3.2.1.19
The MAC address assigned to the virtual router interface of this VLAN. This field is meaningful only if rcVlanRoutingEnable is equal to true(1).
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rcVlanRowStatus		1.3.6.1.4.1.2272.1.3.2.1.20
Used to create/delete entries in the rcVlanTable.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcVlanIgmpSnoopEnable		1.3.6.1.4.1.2272.1.3.2.1.21
A flag to note whether IGMP Snooping is enabled on this VLAN.
Status: deprecated	Access: read-write
OBJECT-TYPE
	TruthValue

rcVlanIgmpSnoopReportProxyEnable		1.3.6.1.4.1.2272.1.3.2.1.22
A flag to note whether IGMP Report Proxy is enabled on this VLAN.
Status: deprecated	Access: read-write
OBJECT-TYPE
	TruthValue

rcVlanIgmpSnoopRobustness		1.3.6.1.4.1.2272.1.3.2.1.23
This variable allows tuning for the expected packet loss on a subnet. If a subnet is expected to be lossy, the Robustness variable may be increased. IGMP is robust to (Robustness - 1) packet losses.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	1..255

rcVlanIgmpSnoopQueryInterval		1.3.6.1.4.1.2272.1.3.2.1.24
The interval (in seconds) between IGMP Host-Query packets transmitted on this interface.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

rcVlanIgmpSnoopMRouterPorts		1.3.6.1.4.1.2272.1.3.2.1.25
The set of ports in this VLAN that provide connectivity to an IP Multicast router.
Status: deprecated	Access: read-write
OBJECT-TYPE
	PortSet

rcVlanUserDefinedPid		1.3.6.1.4.1.2272.1.3.2.1.26
When rcVlanProtocolId is set to usrDefined(15) in a protocol-based VLAN, this field represents the 16-bit user defined protocol identifier.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcVlanIgmpSnoopActiveMRouterPorts		1.3.6.1.4.1.2272.1.3.2.1.27
Active ports.
Status: deprecated	Access: read-only
OBJECT-TYPE
	PortSet

rcVlanProtocolIds		1.3.6.1.4.1.2272.1.3.2.1.28
Bitfield of protocol ids.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcVlanIgmpSnoopActiveQuerier		1.3.6.1.4.1.2272.1.3.2.1.29
IP address of multicast querier router.
Status: deprecated	Access: read-only
OBJECT-TYPE
	IpAddress

rcVlanIgmpSnoopMRouterExpiration		1.3.6.1.4.1.2272.1.3.2.1.30
Multicast querier router aging time out.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Integer32

rcVlanIgmpSnoopQuerierPort		1.3.6.1.4.1.2272.1.3.2.1.31
The port on which the multicast querier router was heard.
Status: deprecated	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcVlanUserPriority		1.3.6.1.4.1.2272.1.3.2.1.32
User priority level.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	level0(0), level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7)

rcVlanQosLevel		1.3.6.1.4.1.2272.1.3.2.1.33
Used to specify the Qos level packets, carried in this VLAN, should be processed with.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	level0(0), level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7)

rcVlanTosValue		1.3.6.1.4.1.2272.1.3.2.1.34
Tos value.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..64

rcVlanEncap		1.3.6.1.4.1.2272.1.3.2.1.35
This is the encapsulation type for userdefined protocol based vlans. This is not meaningful for other types of vlan. The default value is null.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ethernet2(1), llc(2), snap(3), all(4), notapplicable(5)

rcVlanFirewallVlanType		1.3.6.1.4.1.2272.1.3.2.1.36
This is the firewall vlan type for port based vlans.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), naap(2), enforceable(3), peering(4)

rcVlanFdbAging		1.3.6.1.4.1.2272.1.3.2.1.37
The timeout period (in seconds) used for aging out fdb entries of this VLAN.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0 | 10..1000000

rcVlanFirewallClusterId		1.3.6.1.4.1.2272.1.3.2.1.43
Firewall cluster Id
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..64

rcVlanOspfPassivePortMember		1.3.6.1.4.1.2272.1.3.2.1.44
The set of ports in the vlan that are designated as ospf passive
Status: current	Access: read-write
OBJECT-TYPE
	PortSet

rcVlanUnkDstMacDiscard		1.3.6.1.4.1.2272.1.3.2.1.45
Enable/disable Unknown Destination Mac Discard on Vlan
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcVlanNlbMode		1.3.6.1.4.1.2272.1.3.2.1.46
NLB mode set on a VLAN.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nlbAdminDisable(0), nlbAdminIgmpMcast(1), nlbAdminMulticast(2), nlbAdminUnicast(4)

rcVlanVrfId		1.3.6.1.4.1.2272.1.3.2.1.48
Indicates the Virtual Router to which the VLAN belongs
Status: current	Access: read-write
OBJECT-TYPE
	VrfIdentifier

rcVlanVrfName		1.3.6.1.4.1.2272.1.3.2.1.49
The Name of the Virtual Router to which the VLAN belongs
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..64)

rcVlanNodalMepList		1.3.6.1.4.1.2272.1.3.2.1.54
List of nodal Meps assigned to this vlan. A mep consists of Domain Name, Association name and Mep Id separated by '.'. Each meps is separated by ',': ..,..,... The maximum number of nodal Mep for each vlan is 8.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..408)

rcVlanNumOfNodalMep		1.3.6.1.4.1.2272.1.3.2.1.55
Number of nodal meps assigned to this vlan
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..8

rcVlanNodalMipLevelList		1.3.6.1.4.1.2272.1.3.2.1.56
List of nodal Mip levels assigned to this vlan that allows Mip functionality to be enabled on a per level per vlan basis. A mip level is represented by an integer ranging from 0 to 7. The mip levels are separated by ',': <0...7>,<0...7>,... The maximum number of nodal Mip levels for each vlan is 8.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..16)

rcVlanNumOfNodalMipLevel		1.3.6.1.4.1.2272.1.3.2.1.57
Number of nodal mip levels assigned to this vlan that allows MIP functionality to be enabled on a per level per vlan basis.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..8

rcVlanIpMultinettingEnable		1.3.6.1.4.1.2272.1.3.2.1.59
Indicate if the vlan is an Ip Multinetting vlan. If enabled, rcVlanAssociatedIpMultinettingVlan should be set to 0
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcVlanAssociatedIpMultinettingVlan		1.3.6.1.4.1.2272.1.3.2.1.60
Associated Ip Multinetting vlan Id whose rcVlanIpMultinettingEnable attribute is set
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..4095

rcVlanPlsbIsid		1.3.6.1.4.1.2272.1.3.2.1.61
Plsb i-sid number assigned to a C-vlan. Default 0 value indicates that no i-sid has been assinged.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..16777215

rcVlanPortTable		1.3.6.1.4.1.2272.1.3.3
A table used to maintain VLAN port related information.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcVlanPortEntry

rcVlanPortEntry		1.3.6.1.4.1.2272.1.3.3.1
Entry containing VLAN information regarding a particular port.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcVlanPortEntry

rcVlanPortIndex		1.3.6.1.4.1.2272.1.3.3.1.1
An unique index used to identify a particular port in the system. This index is equal to the ifIndex of the port.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

rcVlanPortNumVlanIds		1.3.6.1.4.1.2272.1.3.3.1.2
Used to indicate the number of VLAN IDs that are stored in the rcVlanPortVlanIds variable.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcVlanPortVlanIds		1.3.6.1.4.1.2272.1.3.3.1.3
An array used to identify which VLANs this port is assigned to. Each VLAN ID is stored as a two octet value. The first octet in the pair holds bits 15-8 of the VLAN ID, while the second octet holds bits 7-0 of the VLAN ID. This object is now replaced by rcVlanPortVlanIdList.
Status: deprecated	Access: read-write
OBJECT-TYPE
	IdList	Size(0..4096)

rcVlanPortType		1.3.6.1.4.1.2272.1.3.3.1.4
The type of port: access(1) or trunk(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	access(1), trunk(2)

rcVlanPortDiscardTaggedFrames		1.3.6.1.4.1.2272.1.3.3.1.5
A flag used to determine how to process tagged frames received on this access port. When the flag is set, these frames are discarded by the forwarding process. When the flag is reset, these frames are processed normally. This field is meaningless when the port is not an access port and should be set to false(2).
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcVlanPortDiscardUntaggedFrames		1.3.6.1.4.1.2272.1.3.3.1.6
A flag used to determine how to process untagged frames received on this trunk port. When the flag is set, these frames are discarded by the forwarding process. When the flag is reset, these frames are assigned to the VLAN specified by rcVlanPortDefaultVlanId. This field is meaningless when the port is not a trunk port and should be set to false(2).
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcVlanPortDefaultVlanId		1.3.6.1.4.1.2272.1.3.3.1.7
The VLAN ID assigned to untagged frames received on this trunk port. This field is meaningless when the port is not a trunk port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..4094

rcVlanPortPerformTagging		1.3.6.1.4.1.2272.1.3.3.1.8
Enable/disable the port on the current vlan to perform tagging on the incoming and outgoing traffic.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcVlanPortSVlanPortType		1.3.6.1.4.1.2272.1.3.3.1.9
The type of port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	normal(1), uni(2), nni(3)

rcVlanPortLoopDetect		1.3.6.1.4.1.2272.1.3.3.1.10
Enable/disable loop detection on this port
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcVlanPortFirstPortInOpid		1.3.6.1.4.1.2272.1.3.3.1.11
This value gives the IfIndex of the first port in the octapid. This value is used to generate an error message when changing port type from normal to uni/nni and viceversa
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcVlanPortLastPortInOpid		1.3.6.1.4.1.2272.1.3.3.1.12
This value gives the IfIndex of the first port in the octapid. This value is used to generate an error message when changing port type from normal to uni/nni and viceversa
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcVlanPortUntagDefaultVlan		1.3.6.1.4.1.2272.1.3.3.1.13
enable/disable Egress Tagging on the Default Vlan of the port.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcVlanPortLoopDetectAction		1.3.6.1.4.1.2272.1.3.3.1.14
This value is used to specify the action which needs to be taken once a loop is detected on a specific port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	portDown(1), vlanBlock(2), macDiscard(3)

rcVlanPortArpDetect		1.3.6.1.4.1.2272.1.3.3.1.15
Enable/disable Arp detection on this port
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcVlanPortSpoofDetect		1.3.6.1.4.1.2272.1.3.3.1.16
Enable/disable spoof detection on this port
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcVlanPortVlanIdList		1.3.6.1.4.1.2272.1.3.3.1.21
This bitfield is used to identify which VLANs this port is assigned to. Each VLAN ID is stored as a bit. The most-significant (left-most) bit represents Vlan Id 1.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..512)

rcVlanMacTable		1.3.6.1.4.1.2272.1.3.4
A table used to maintain MAC addresses assigned to a particular VLAN by MAC address.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcVlanMacEntry

rcVlanMacEntry		1.3.6.1.4.1.2272.1.3.4.1
Entry containing VLAN information regarding a particular port.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcVlanMacEntry

rcVlanMacVlanId		1.3.6.1.4.1.2272.1.3.4.1.1
An unique index used to identify a VLAN (by MAC address) in the system.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

rcVlanMacAddr		1.3.6.1.4.1.2272.1.3.4.1.2
An unique index used to identify a MAC address assigned to a particular VLAN.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rcVlanMacRowStatus		1.3.6.1.4.1.2272.1.3.4.1.3
Row status for this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcVlanIgmpSnoopNumGroups		1.3.6.1.4.1.2272.1.3.5
The number of entries (rows) in the rcVlanIgmpSnoopTable.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcVlanIgmpSnoopTable		1.3.6.1.4.1.2272.1.3.6
The (conceptual) table listing the IP multicast groups for which there are members on a particular interface on a particular VLAN (i.e., a list known multicast receivers). A row is created by the system when it receives an IGMP Join messages on a port.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcVlanIgmpSnoopEntry

rcVlanIgmpSnoopEntry		1.3.6.1.4.1.2272.1.3.6.1
An entry (row) in the rcVlanIgmpSnoopTable.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	RcVlanIgmpSnoopEntry

rcVlanIgmpSnoopVlanId		1.3.6.1.4.1.2272.1.3.6.1.1
The VLAN for which this entry contains information.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	1..4094

rcVlanIgmpSnoopIpAddress		1.3.6.1.4.1.2272.1.3.6.1.2
The IP multicast group address for which this entry contains information.
Status: deprecated	Access: read-only
OBJECT-TYPE
	IpAddress

rcVlanIgmpSnoopIfIndex		1.3.6.1.4.1.2272.1.3.6.1.3
The interface for which this entry contains information for this IP multicast group address (i.e., the port the Join message was received).
Status: deprecated	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcVlanIgmpSnoopMember		1.3.6.1.4.1.2272.1.3.6.1.4
The IP Address of the source of the membership report received for this IP Multicast group address on this interface (i.e., the address of the host sending the Join message).
Status: deprecated	Access: read-only
OBJECT-TYPE
	IpAddress

rcVlanIgmpSnoopExpiration		1.3.6.1.4.1.2272.1.3.6.1.5
The minimum amount of time remaining before this entry will be aged out.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Integer32

rcVlanIgmpSnoopType		1.3.6.1.4.1.2272.1.3.6.1.6
The type of entry: dynamic(1) entries are created by snooping IGMP messages, static(2) entries are created via management.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	dynamic(1), static(2), blocked(3)

rcVlanIgmpSnoopStaticTable		1.3.6.1.4.1.2272.1.3.7
The (conceptual) table listing the statically- defined IP multicast groups for which there are members on a particular interface on a particular VLAN.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcVlanIgmpSnoopStaticEntry

rcVlanIgmpSnoopStaticEntry		1.3.6.1.4.1.2272.1.3.7.1
An entry (row) in the rcVlanIgmpSnoopStaticTable.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	RcVlanIgmpSnoopStaticEntry

rcVlanIgmpSnoopStaticVlanId		1.3.6.1.4.1.2272.1.3.7.1.1
The VLAN for which this entry contains information.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	1..4094

rcVlanIgmpSnoopStaticIpAddress		1.3.6.1.4.1.2272.1.3.7.1.2
The IP multicast group address for which this entry contains information. The address must fall within 224.0.1.0 to 239.255.255.255.
Status: deprecated	Access: read-only
OBJECT-TYPE
	IpAddress

rcVlanIgmpSnoopStaticMemberPorts		1.3.6.1.4.1.2272.1.3.7.1.3
The set of ports in this VLAN multicast traffic for the rcVlanIgmpSnoopStaticIpAddress is to be forwarded to.
Status: deprecated	Access: read-write
OBJECT-TYPE
	PortSet

rcVlanIgmpSnoopStaticRowStatus		1.3.6.1.4.1.2272.1.3.7.1.4
Used to create/delete entries in the rcVlanIgmpSnoopStaticTable.
Status: deprecated	Access: read-write
OBJECT-TYPE
	RowStatus

rcVlanIgmpSnoopStaticNotAllowedToJoin		1.3.6.1.4.1.2272.1.3.7.1.5
Not allowed to join
Status: deprecated	Access: read-write
OBJECT-TYPE
	PortSet

rcVlanIgmpSnoopAccessTable		1.3.6.1.4.1.2272.1.3.8
Table used to specify which host(s) can send and/or receive IP Multicast traffic.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcVlanIgmpSnoopAccessEntry

rcVlanIgmpSnoopAccessEntry		1.3.6.1.4.1.2272.1.3.8.1
An entry (row) in the rcVlanIgmpSnoopAccessTable.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	RcVlanIgmpSnoopAccessEntry

rcVlanIgmpSnoopAccessVlanId		1.3.6.1.4.1.2272.1.3.8.1.1
The VLAN for which this entry contains information.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	1..4094

rcVlanIgmpSnoopAccessGrpAddr		1.3.6.1.4.1.2272.1.3.8.1.2
The IP multicast group address for which this entry contains information.
Status: deprecated	Access: read-only
OBJECT-TYPE
	IpAddress

rcVlanIgmpSnoopAccessHostAddr		1.3.6.1.4.1.2272.1.3.8.1.3
The IP address of a host for which this entry contains information.
Status: deprecated	Access: read-only
OBJECT-TYPE
	IpAddress

rcVlanIgmpSnoopAccessHostMask		1.3.6.1.4.1.2272.1.3.8.1.4
The IP netmask of a host for which this entry contains information.
Status: deprecated	Access: read-only
OBJECT-TYPE
	IpAddress

rcVlanIgmpSnoopAccessMode		1.3.6.1.4.1.2272.1.3.8.1.5
Used to specify whether the host identified by rcVlanIgmpSnoopAccessHostAddr should be denied IP multicast transmit, receive, or both.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	denyTx(1), denyRx(2), denyBoth(3)

rcVlanIgmpSnoopAccessRowStatus		1.3.6.1.4.1.2272.1.3.8.1.6
Row status
Status: deprecated	Access: read-write
OBJECT-TYPE
	RowStatus

rcVlanIgmpSnoopSenderTable		1.3.6.1.4.1.2272.1.3.9
The (conceptual) table listing the IP multicast groups for which there are members on a particular interface on a particular VLAN (i.e., a list known multicast senders). A row is created by the system when it receives an IGMP Join messages on a port.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcVlanIgmpSnoopSenderEntry

rcVlanIgmpSnoopSenderEntry		1.3.6.1.4.1.2272.1.3.9.1
An entry (row) in the rcVlanIgmpSnoopSenderTable.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	RcVlanIgmpSnoopSenderEntry

rcVlanIgmpSnoopSenderVlanId		1.3.6.1.4.1.2272.1.3.9.1.1
The VLAN for which this entry contains information.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	1..4094

rcVlanIgmpSnoopSenderIpAddress		1.3.6.1.4.1.2272.1.3.9.1.2
The IP multicast group address for which this entry contains information.
Status: deprecated	Access: read-only
OBJECT-TYPE
	IpAddress

rcVlanIgmpSnoopSenderIfIndex		1.3.6.1.4.1.2272.1.3.9.1.3
The interface for which this entry contains information for this IP multicast group address (i.e., the port the multicast traffic was received).
Status: deprecated	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcVlanIgmpSnoopSenderMember		1.3.6.1.4.1.2272.1.3.9.1.4
The IP Address of the host sending the multicast traffic.
Status: deprecated	Access: read-only
OBJECT-TYPE
	IpAddress

rcVlanIgmpSnoopSenderAction		1.3.6.1.4.1.2272.1.3.9.1.5
Used to specify an action to perform on this group.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), flushEntry(1), flushGrp(2)

rcVlanLoopDetectedTable		1.3.6.1.4.1.2272.1.3.10
A list of Vlans the port belongs to and the corresponding loop detected status.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcVlanLoopDetectedEntry

rcVlanLoopDetectedEntry		1.3.6.1.4.1.2272.1.3.10.1
Loop-Detected Entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcVlanLoopDetectedEntry

rcVlanLoopDetectedPortIndex		1.3.6.1.4.1.2272.1.3.10.1.1
Port Number.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

rcVlanLoopDetectedVlanId		1.3.6.1.4.1.2272.1.3.10.1.2
Gives the VlanId to which the port belongs.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

rcVlanLoopDetectedValue		1.3.6.1.4.1.2272.1.3.10.1.3
Gives the Loop Detected status of the port in a vlan.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	no(0), yes(1)

rcVlanDsapSsapTable		1.3.6.1.4.1.2272.1.3.11
A table used to maintain DSAP/SSAP values assigned to a sna802dot2 or userdefined vlan.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcVlanDsapSsapEntry

rcVlanDsapSsapEntry		1.3.6.1.4.1.2272.1.3.11.1
An entry in the rcVlanDsapSsap table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcVlanDsapSsapEntry

rcVlanDsapSsapVlanId		1.3.6.1.4.1.2272.1.3.11.1.1
A unique index to identify a vlan.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..2147483647

rcVlanDsapSsapPid		1.3.6.1.4.1.2272.1.3.11.1.2
Values of DSAP/SSAP assigned to a particular vlan.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..ffff

rcVlanDsapSsapRowStatus		1.3.6.1.4.1.2272.1.3.11.1.3
Row Status.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcVlanNewLoopDetectedTable		1.3.6.1.4.1.2272.1.3.12
A list of Vlans the port belongs to and the corresponding loop detected status.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcVlanNewLoopDetectedEntry

rcVlanNewLoopDetectedEntry		1.3.6.1.4.1.2272.1.3.12.1
Loop-Detected Entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcVlanNewLoopDetectedEntry

rcVlanNewLoopDetectedPortIndex		1.3.6.1.4.1.2272.1.3.12.1.1
Port Number.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

rcVlanNewLoopDetectedVlanId		1.3.6.1.4.1.2272.1.3.12.1.2
Gives the VlanId to which the port belongs.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..2147483647

rcVlanNewLoopDetectedMac		1.3.6.1.4.1.2272.1.3.12.1.3
Mac address
Status: current	Access: not-accessible
OBJECT-TYPE
	MacAddress

rcVlanNewLoopDetectedAction		1.3.6.1.4.1.2272.1.3.12.1.4
This value is used to specify the action which needs to be taken once a loop is detected on a specific port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	portDown(1), vlanBlock(2), macDiscard(3)

rcVlanNewLoopDetectedSmltRemote		1.3.6.1.4.1.2272.1.3.12.1.5
A MAC address indicate for remote learnt, either local or remote.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcVlanClearMacRecordTable		1.3.6.1.4.1.2272.1.3.17
Table used to clear a Vlan MAC Record.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcVlanClearMacRecordEntry

rcVlanClearMacRecordEntry		1.3.6.1.4.1.2272.1.3.17.1
Vlan Clear Mac Record Table Entry
Status: current	Access: not-accessible
OBJECT-TYPE
	RcVlanClearMacRecordEntry

rcVlanClearMacRecordAddr		1.3.6.1.4.1.2272.1.3.17.1.1
Mac Address that needs to be cleared.
Status: current	Access: not-accessible
OBJECT-TYPE
	MacAddress

rcVlanClearMacRecordVlanId		1.3.6.1.4.1.2272.1.3.17.1.2
Vlan Id where the Mac record has to be cleared.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..4094

rcVlanClearMacRecordAllVlanIds		1.3.6.1.4.1.2272.1.3.17.1.3
When set to true, this will clear the MAC record on all the Vlan Ids it exists.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcVlanClearMacRecordForceDelete		1.3.6.1.4.1.2272.1.3.17.1.4
By default, when ForceDelete is set to false, MAC record will not be cleared if an ARP record is associated with this Mac Address. If ForceDelete is set to True, MAC record will be removed even when an ARP is associated with this record.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcVlanClearMacRecordLCForceDelete		1.3.6.1.4.1.2272.1.3.17.1.5
By default, when LCForceDelete (Line Card Force Delete) is set to false, if the MAC record is not found on the CP, then no message will be sent to the line-card. When LCForceDelete is set to true, a message will be sent to the line-card even when the MAC record is not found on the CP.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcChasType		1.3.6.1.4.1.2272.1.4.1
Chassis Type
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), a1100(2), a1250(6), a1150(7), a1200(8), a1050(9), a8006(280887558), a8010(280887562), a8010co(1623064842), a8003(280887555), a8003r(280891651)

rcChasSerialNumber		1.3.6.1.4.1.2272.1.4.2
Unique serial number for this chassis.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..16)

rcChasHardwareRevision		1.3.6.1.4.1.2272.1.4.3
Device hardware revision level
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..20)

rcChasNumSlots		1.3.6.1.4.1.2272.1.4.4
The number of slots in the chassis available for plug-in cards.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..16

rcChasNumPorts		1.3.6.1.4.1.2272.1.4.5
The total number of ports currently installed in the chassis.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..255

rcChasTestResult		1.3.6.1.4.1.2272.1.4.6
Chassis start-up diagnostic tests.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), ok(2), crceeprom(3), timer(4), procdram(5), led(6), formaccpuaccess(7), asiccpuaccess(8), memory(9), loopback(10)

rcChasFan		1.3.6.1.4.1.2272.1.4.7
OBJECT IDENTIFIER

rcChasFanTable		1.3.6.1.4.1.2272.1.4.7.1
This table contains information about Fans
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcChasFanEntry

rcChasFanEntry		1.3.6.1.4.1.2272.1.4.7.1.1
Contains information regarding a Fan Unit
Status: current	Access: not-accessible
OBJECT-TYPE
	RcChasFanEntry

rcChasFanId		1.3.6.1.4.1.2272.1.4.7.1.1.1
The chassis fan Id.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4

rcChasFanOperStatus		1.3.6.1.4.1.2272.1.4.7.1.1.2
Actual status of the Fan: - unknown(1) - status can not be determined. - up(2) - present and supplying power. - down(3) - present, but failure indicated.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), up(2), down(3)

rcChasFanAmbientTemperature		1.3.6.1.4.1.2272.1.4.7.1.1.3
Used to indicate the temperature of the air entering the fan.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcChasFanType		1.3.6.1.4.1.2272.1.4.7.1.1.4
Type of the Fan: - unknown(1) - type can not be determined. - regularSpeed(2) - regular speed fan is present. - highSpeed(3) - high speed fan is present.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), regularSpeed(2), highSpeed(3)

rcChasPowerSupply		1.3.6.1.4.1.2272.1.4.8
OBJECT IDENTIFIER

rcChasPowerSupplyTable		1.3.6.1.4.1.2272.1.4.8.1
This table contains information about power supplies.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcChasPowerSupplyEntry

rcChasPowerSupplyEntry		1.3.6.1.4.1.2272.1.4.8.1.1
Contains information regarding a power supply unit.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcChasPowerSupplyEntry

rcChasPowerSupplyId		1.3.6.1.4.1.2272.1.4.8.1.1.1
The power supply Id.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..3

rcChasPowerSupplyOperStatus		1.3.6.1.4.1.2272.1.4.8.1.1.2
Actual status of the power supply: - unknown(1) - status can not be determined. - empty(2) - power supply not installed. - up(3) - present and supplying power. - down(4) - present, but failure indicated.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), empty(2), up(3), down(4)

rcChasPowerSupplyDetailTable		1.3.6.1.4.1.2272.1.4.8.2
This table contains detailed information about power supplies.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcChasPowerSupplyDetailEntry

rcChasPowerSupplyDetailEntry		1.3.6.1.4.1.2272.1.4.8.2.1
Contains detailed info regarding a power supply unit.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcChasPowerSupplyDetailEntry

rcChasPowerSupplyDetailId		1.3.6.1.4.1.2272.1.4.8.2.1.1
The power supply Id.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..3

rcChasPowerSupplyDetailType		1.3.6.1.4.1.2272.1.4.8.2.1.2
The power supply type.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(0), ac(1), dc(2)

rcChasPowerSupplyDetailSerialNumber		1.3.6.1.4.1.2272.1.4.8.2.1.3
The power supply serial number.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..16)

rcChasPowerSupplyDetailHardwareRevision		1.3.6.1.4.1.2272.1.4.8.2.1.4
The hardware revision of the power supply.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..16)

rcChasPowerSupplyDetailPartNumber		1.3.6.1.4.1.2272.1.4.8.2.1.5
The power supply part number.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..16)

rcChasPowerSupplyDetailDescription		1.3.6.1.4.1.2272.1.4.8.2.1.6
The detail description of power supply.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..64)

rcChasPowerSupplyDetailInputLineVoltage		1.3.6.1.4.1.2272.1.4.8.2.1.8
The power supply Input Line voltage.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(0), low110v(1), high220v(2), minus48v(3)

rcChasPowerSupplyDetailOperLineVoltage		1.3.6.1.4.1.2272.1.4.8.2.1.9
The power supply Line voltage considered for Power Management calculation.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(0), low110v(1), high220v(2), minus48v(3)

rcCard		1.3.6.1.4.1.2272.1.4.9
OBJECT IDENTIFIER

rcCardTable		1.3.6.1.4.1.2272.1.4.9.1
A table that contains information about the cards in this chassis. For those slots that do not contain a physical card, the table may be implemented to contain a conceptual row with the type of physical module set to 'chasCardEmpty', or it may be implemented to have no conceptual row instance.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcCardEntry

rcCardEntry		1.3.6.1.4.1.2272.1.4.9.1.1
Card attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	RcCardEntry

rcCardIndex		1.3.6.1.4.1.2272.1.4.9.1.1.1
A unique value for each module within the chassis. This value is determined by the chassis slot number where the module is inserted. Valid entries are 1 to the value of rcChasNumSlots
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..10

rcCardType		1.3.6.1.4.1.2272.1.4.9.1.1.2
Used to indicate a card types in the Accelar 1000 product families. For Accelar 1000 devices, gigabit cards use an encoded value according to the following rule: +-----+--+-+---+---+---+ bits : |31-11|10|9|8-7|6-4|3-0| +-----+--+-+---+---+---+ field : | a | b|c| d | e | f | +-----+--+-+---+---+---+ a : not-used b : 1=gigabit c : 0=non-redundant, 1=redundant d : 0=short-haul, 1=long-haul, 2=extra-distance, e : 0=work-group(a1100 & a1150) 1=back-bone(a1200 & f1250 & f2000), f : 1=1-port, 2=2-port, 4=4-port, 8=8-port
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), rcCPU(2), rc8x100BaseTX(3), rc8x100BaseT2(4), rc8x100BaseF(5), rc16x100BaseTX(6), rc8x100BaseTXWG(12), rc16x100BaseTXWG(13), rc4x100BaseFWG(14), rc12x100BaseTXWG(15), rc12x100BaseFBB(16), rc8x100BaseFWG(17), rc12x100BaseTX-2x100BaseFBB(18), rc2x155BaseFBB(19), rc4x155BaseFBB(20), rc16x100BaseFBB(21), rc14x100BaseTX-2x100BaseFBB(22), rc8x10BaseFBB(23), rc4xOC3(24), rc1xOC12(25), rcRMON(26), rc1xOC12POSBaseMMF(27), rc1xOC12POSBaseSMF(28), rc4x1000BaseSXWG(1028), rc1x1000BaseSXWG(1025), rc2x1000BaseSXWG(1026), rc1x1000BaseSXRWG(1537), rc2x1000BaseSXRWG(1538), rc1x1000BaseLXWG(1153), rc2x1000BaseLXWG(1154), rc2x1000BaseXDWG(1282), rc1x1000BaseLXRWG(1665), rc2x1000BaseLXRWG(1666), rc1x1000BaseSXBB(1041), rc2x1000BaseSXBB(1042), rc1x1000BaseSXRBB(1553), rc2x1000BaseSXRBB(1554), rc1x1000BaseLXBB(1169), rc2x1000BaseLXBB(1170), rc2x1000BaseXDBB(1298), rc1x1000BaseLXRBB(1681), rc2x1000BaseLXRBB(1682)

rcCardSerialNumber		1.3.6.1.4.1.2272.1.4.9.1.1.3
Unique serial number for this card.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..16)

rcCardHardwareRevision		1.3.6.1.4.1.2272.1.4.9.1.1.4
Hardware Version
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..8)

rcCardAdminStatus		1.3.6.1.4.1.2272.1.4.9.1.1.5
Used to indicate the administrative status of this card
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	up(1), down(2), testing(3)

rcCardOperStatus		1.3.6.1.4.1.2272.1.4.9.1.1.6
Used to indicate the operational status of this card.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2), testing(3), unknown(4), dormant(5)

rcCardPCMCIAType		1.3.6.1.4.1.2272.1.4.9.1.1.7
Used to indicate the type of PCMCIA card currently installed in this CPU card, if any. For non-CPU cards, this variable has no meaning and will always be set to none.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), modem28kbs(2), flash2meg(3), flash4meg(4)

rcCardPartNumber		1.3.6.1.4.1.2272.1.4.9.1.1.8
Card Part Number
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..16)

rcPort		1.3.6.1.4.1.2272.1.4.10
OBJECT IDENTIFIER

rcPortTable		1.3.6.1.4.1.2272.1.4.10.1
Port table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPortEntry

rcPortEntry		1.3.6.1.4.1.2272.1.4.10.1.1
Entry containing info. for a particular port
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPortEntry

rcPortIndex		1.3.6.1.4.1.2272.1.4.10.1.1.1
An index value that uniquely identifies a port. This value is similar to ifIndex in MIB2.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcPortType		1.3.6.1.4.1.2272.1.4.10.1.1.2
Port type
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	other(0), rc100BaseTX(1), rc100BaseT2(2), rc100BaseF(3), rc1000BaseF(4), rc1000BaseDualF(5), rc10BaseF(6), rcPosMMF(7), rcPosSMF(8), rcAtm(9), rcGbicLx(10), rcGbicSx(11), rcGbicXd(12), rcGbicCu(13), rcGbicOther(14), rcOc3cSM(15), rcOc3cMM(16), rcOc3cCOPPER(17), rcOc12cSM(18), rcOc12cMM(19), rcDs3(20), rcE3(21), rcGbicNone(22), rc1000BaseT(23), rcGbicZx(24), rcOc3cAtmSM(25), rcOc3cAtmMM(26), rcOc12cAtmSM(27), rcOc12cAtmMM(28), rcOc3cPosSM(29), rcOc3cPosMM(30), rcOc12cPosSM(31), rcOc12cPosMM(32), rcGbic1470(33), rcGbic1490(34), rcGbic1510(35), rcGbic1530(36), rcGbic1550(37), rcGbic1570(38), rcGbic1590(39), rcGbic1610(40), rcRmon(41), rcGbic1470APD(42), rcGbic1490APD(43), rcGbic1510APD(44), rcGbic1530APD(45), rcGbic1550APD(46), rcGbic1570APD(47), rcGbic1590APD(48), rcGbic1610APD(49), rc10GbLW(50), rc10GbLR(51), rc1000BaseTX(53), rcGbicBx(55), rc10GbNone(56), rc10GbSR(58), rc10GbSW(59), rc10GbER(60), rc10GbEW(61), rc10GbOther(62), rc1000BaseTXPOE(63), rc10GbZR(64), rc10GbZW(65), rcGbic1310Xd(66), rcGbic1470Xd(67), rcGbic1490Xd(68), rcGbic1510Xd(69), rcGbic1530Xd(70), rcGbic1550Xd(71), rcGbic1570Xd(72), rcGbic1590Xd(73), rcGbic1610Xd(74), rcGbic1470Zx(75), rcGbic1490Zx(76), rcGbic1510Zx(77), rcGbic1530Zx(78), rcGbic1550Zx(79), rcGbic1570Zx(80), rcGbic1590Zx(81), rcGbic1610Zx(82), rcGbic1690Zx(83), rcGbic1310Bx(84), rcGbic1490Bx(85), rcGbicEx(86), rcGbic850Sx(87), rcGbic1200Lx(88), rcGbic1300Lx(89), rcGbic1310Lx(90), rcGbic1490Lx(91), rcGbic1550Lx(92), rcGbic1550Ex(93), rc1GbFD(94), rc10GbLRM(95), rc10GbDWDMR(96), rc10GbDWDMW(97), rcGbic1300SeFx(104), rc10GbCX(106)

rcPortConnectorType		1.3.6.1.4.1.2272.1.4.10.1.1.3
Type of connector installed on this port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	nonRedundant(1), redundant(2)

rcPortPerformRouting		1.3.6.1.4.1.2272.1.4.10.1.1.4
Indicate whether this port should perform routing
Status: deprecated	Access: read-write
OBJECT-TYPE
	TruthValue

rcPortHighPriority		1.3.6.1.4.1.2272.1.4.10.1.1.5
Indicate whether this port should be treated with high priority
Status: deprecated	Access: read-write
OBJECT-TYPE
	TruthValue

rcPortAction		1.3.6.1.4.1.2272.1.4.10.1.1.6
Port related actions.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), flushMacFdb(2), flushArp(3), flushIp(4), flushAll(5), triggerRipUpdate(6), clearLoopDetectAlarm(7)

rcPortResult		1.3.6.1.4.1.2272.1.4.10.1.1.7
Result from the last Vlan action.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), inProgress(2), success(3), fail(4)

rcPortPrimaryConnector		1.3.6.1.4.1.2272.1.4.10.1.1.8
For ports configured with redundant connectors, this value is used to indicate which connector should be used as the 'active' connector on this port the next time the port is placed into the ifAdminStatus=Up.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	left(1), right(2), other(3)

rcPortActiveConnector		1.3.6.1.4.1.2272.1.4.10.1.1.9
For ports configured with redundant connectors, this value is used to indicate which connector is currently the active one. Only one connector can be active an anytime.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	left(1), right(2), other(3)

rcPortBackupConnectorStatus		1.3.6.1.4.1.2272.1.4.10.1.1.10
Indicate the status of the link attached to the back-up (non-active) connector.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2), other(3)

rcPortAutoNegotiate		1.3.6.1.4.1.2272.1.4.10.1.1.11
Indicate whether this port enabled for auto negotiations or not.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcPortAdminDuplex		1.3.6.1.4.1.2272.1.4.10.1.1.12
Indicates the port duplex type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	half(1), full(2)

rcPortOperDuplex		1.3.6.1.4.1.2272.1.4.10.1.1.13
Indicate this port's current duplex value.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	half(1), full(2)

rcPortAdminSpeed		1.3.6.1.4.1.2272.1.4.10.1.1.14
Indicate this port's speed.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), mbps10(1), mbps100(2), mbps1000(3), mbps10000(4)

rcPortOperSpeed		1.3.6.1.4.1.2272.1.4.10.1.1.15
Indicate this port's current speed value.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPortMltId		1.3.6.1.4.1.2272.1.4.10.1.1.16
Indicate which multi-link trunk (MLT) this port is assigned to. If this port is not associated with any MLT, this value will be set to zero(0).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPortLocked		1.3.6.1.4.1.2272.1.4.10.1.1.17
Indicate whether this port is locked.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcPortAutoNegotiationSupported		1.3.6.1.4.1.2272.1.4.10.1.1.18
Indicate whether this port can support auto-negotiation.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcPortSingleRoutablePort		1.3.6.1.4.1.2272.1.4.10.1.1.19
Indicate whether this port is a single routable port. If this value is true, the port functions like a traditional router port.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcPortUnknownMacDiscard		1.3.6.1.4.1.2272.1.4.10.1.1.20
If rcUnknownMacDiscard is set to True, then a packet with an unknown source MAC address is dropped on that port, and other ports then will discard any packets with this MAC address in the destination field. For example, suppose 11:22:33:44:55:66 is an unknown source MAC, packets with source MAC 11:22:33:44:55 coming from this port is discarded, further more, packets with destination MAC 11:22:33:44:55:66 coming from other ports are also discarded, unless this address is later learned on another port or the restriction ages out.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcPortNumStateTransition		1.3.6.1.4.1.2272.1.4.10.1.1.21
# state transitions.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcPortUserPriority		1.3.6.1.4.1.2272.1.4.10.1.1.22
User priority level.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	level0(0), level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7)

rcPortAllowOversizeFrame		1.3.6.1.4.1.2272.1.4.10.1.1.23
Used to specify whether over-size frames should be processed or dropped.
Status: deprecated	Access: read-write
OBJECT-TYPE
	TruthValue

rcPortQosLevel		1.3.6.1.4.1.2272.1.4.10.1.1.30
Used to specify the Qos level packets, carried on this port, should be processed with.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	level0(0), level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7)

rcPortDiffServEnable		1.3.6.1.4.1.2272.1.4.10.1.1.31
Used to enable/disable the Differentiated Service feature on this port.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcPortDiffServType		1.3.6.1.4.1.2272.1.4.10.1.1.32
Used to specify the Differentiated Service type for this port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), access(1), core(2)

rcPortDiffServIeee8021POverrideEnable		1.3.6.1.4.1.2272.1.4.10.1.1.33
Used to enable/disable the Differentiated Service IEEE 802.1P over-ride feature.
Status: deprecated	Access: read-write
OBJECT-TYPE
	TruthValue

rcPortVendorDescr		1.3.6.1.4.1.2272.1.4.10.1.1.34
Used to show the name of the vendor of this port's connector. Only applicable to ports on a GBIC cards.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(16)

rcPortName		1.3.6.1.4.1.2272.1.4.10.1.1.35
This port's name.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..42)

rcPortOctapidId		1.3.6.1.4.1.2272.1.4.10.1.1.36
The octapid id of the mirrored port.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Integer32

rcPortWan		1.3.6.1.4.1.2272.1.4.10.1.1.37
Indicatie this port's current WAN/LAN mode. Valid for 10 GE only
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), wan(1), lan(2)

rcPortTransport		1.3.6.1.4.1.2272.1.4.10.1.1.38
Indicatie this port's current tranport layer. Valid for 10 GE only
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), sonet(1), sdh(2)

rcPortMultimediaFilterEnable		1.3.6.1.4.1.2272.1.4.10.1.1.39
Used to enable/disable the Telephony device selected on this port
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcPortMultimediaDevSelection		1.3.6.1.4.1.2272.1.4.10.1.1.40
Used to set/get the selected Multimedia & Telephony Devices on this port. The String is the name of the device in the rcIpFilterMediaDevTable
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rcPortAdminRouting		1.3.6.1.4.1.2272.1.4.10.1.1.43
Indicate whether the port is routable.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcPortOperRouting		1.3.6.1.4.1.2272.1.4.10.1.1.44
The status of the port whether is routable.
Status: current	Access: read-only
OBJECT-TYPE
	EnableValue

rcPortPid		1.3.6.1.4.1.2272.1.4.10.1.1.45
The pid of the mirrored port.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPortIeee8021POverrideEnable		1.3.6.1.4.1.2272.1.4.10.1.1.46
Used to enable/disable IEEE 802.1P override. If it is enabled, 802.1p value from a tagged frame may not be honored.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcPortCpLimitShutDown		1.3.6.1.4.1.2272.1.4.10.1.1.50
A TRUE value indicates if CP Limit shut down the interface.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcPortHighSecureEnable		1.3.6.1.4.1.2272.1.4.10.1.1.51
Enable/Disable high secure feature.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcPortMrouteStrLimit		1.3.6.1.4.1.2272.1.4.10.1.1.55
maximum number of multicast streams that are allowed to ingress to CPU through this port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..32768

rcPortMrouteStrTimerCheck		1.3.6.1.4.1.2272.1.4.10.1.1.56
sampling period to check number of multicast streams that has ingressed CPU through this port in seconds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..3600

rcPortMrouteStrLimitEnable		1.3.6.1.4.1.2272.1.4.10.1.1.57
enable or disable mroute stream limit on port.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcPortAutoNegAd		1.3.6.1.4.1.2272.1.4.10.1.1.62
This object is used to specify the port speed and duplex abilities to be advertised during link negotiation. bit 0 - 10 half duplex advertised bit 1 - 10 full duplex advertised bit 2 - 100 half duplex advertised bit 3 - 100 full duplex advertised bit 4 - 1000 half duplex advertised bit 5 - 1000 full duplex advertised bit 6 - Mac PAUSE frame support advertised bit 7 - Asymmetric PAUSE frame support advertised bit 8 - No advertisements The abilities specified in this object are only used when auto-negotiation is enabled on the port. If all bits in this object are disabled, and auto-negotiation is enabled on the port, then the physical link process on the port will be disabled (if hardware supports this ability). Any change in the value of this bit map will force the PHY to restart the auto-negotiation process. This will have the same effect as physically unplugging and reattaching the cable plant attached to this port. The capabilities being advertised are either all the capabilities supported by the hardware or the user- configured capabilities which is a subset of all the capability supported by hardware. The default value for this object will be all the capabilities supported by the hardware. Note that bit 6 and bit 7 are currently not supported in ERS8600/ERS8800.
Status: current	Access: read-write
OBJECT-TYPE
	BITS	advertise10Half(0), advertise10Full(1), advertise100Half(2), advertise100Full(3), advertise1000Half(4), advertise1000Full(5), advertiseMacPause(6), advertiseAsymPause(7), advertiseNone(8)

rcPortAutoRecoverPort		1.3.6.1.4.1.2272.1.4.10.1.1.64
enable or disable auto recovery of port from action taken by cp-limit, link flap or loop detect features
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcPortExtCplimitConf		1.3.6.1.4.1.2272.1.4.10.1.1.65
Indicates the port configuration for extended CP-LIMIT
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), softDown(2), hardDown(3)

rcPortExtCplimitUtilRate		1.3.6.1.4.1.2272.1.4.10.1.1.66
Threshold for Ingress traffic utilization rate of the port for extended CP-LIMIT
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..100

rcPortEgressRateLimit		1.3.6.1.4.1.2272.1.4.10.1.1.67
Egress Rate Limit.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1000..10000000

rcPortEgressRateLimitState		1.3.6.1.4.1.2272.1.4.10.1.1.68
Used to enable/disable shape/egress-rate-limit functionality.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcPortBpduFilteringTimerCount		1.3.6.1.4.1.2272.1.4.10.1.1.69
The remaining time the port will be disabled due to a BPDU received when BPDU filtering is enabled.
Status: current	Access: read-only
OBJECT-TYPE
	TimeInterval	0..6553500

rcPortBpduFilteringTimeout		1.3.6.1.4.1.2272.1.4.10.1.1.70
The time the port will be disabled when a BPDU is received when BPDU filtering is enabled.
Status: current	Access: read-write
OBJECT-TYPE
	TimeInterval	0..6553500

rcPortBpduFilteringAdminEnabled		1.3.6.1.4.1.2272.1.4.10.1.1.71
Used to enable/disable BPDU filtering.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcPortBpduFilteringOperEnabled		1.3.6.1.4.1.2272.1.4.10.1.1.72
Indicates whether BPDU filtering is actually enabled or disabled.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcPortCpLimitEnable		1.3.6.1.4.1.2272.1.4.10.1.1.75
Used to enable/disable the control packet rate limit. Specifies whether or not rate limiting is currently in operation for multicast and broadcast packets for the specified port.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcPortCpMulticastLimit		1.3.6.1.4.1.2272.1.4.10.1.1.76
Used to limit Multicast traffic on the specified port. Sets the limit in packets per second.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1000..100000

rcPortCpBroadcastLimit		1.3.6.1.4.1.2272.1.4.10.1.1.77
Used to limit Broadcast traffic on the specified port. Sets the limit in packets per second.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1000..100000

rcPortClockSource		1.3.6.1.4.1.2272.1.4.10.1.1.84
Indicates this port's current WAN clock source. Valid for 10 GE WAN only
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), line(1), internal(2)

rcPortIngressRateLimit		1.3.6.1.4.1.2272.1.4.10.1.1.85
Limits the amount of traffic from this Ingress port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1000..10000000

rcPortIngressRateLimitState		1.3.6.1.4.1.2272.1.4.10.1.1.86
Used to enable/disable police/ingress-rate-limit functionality.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcPortVrfIdList		1.3.6.1.4.1.2272.1.4.10.1.1.87
The set of VRF ids to which this port belongs.
Status: current	Access: read-only
OBJECT-TYPE
	IdList	Size(0..512)

rcPortVrfNameList		1.3.6.1.4.1.2272.1.4.10.1.1.96
The set of VRF names to which this port belongs.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

rcPortBrouterVrfId		1.3.6.1.4.1.2272.1.4.10.1.1.97
Gives the VRF Id for this Brouter port.
Status: current	Access: read-write
OBJECT-TYPE
	VrfIdentifier

rcPortBrouterVrfName		1.3.6.1.4.1.2272.1.4.10.1.1.98
Gives the VRF Name for this Brouter port.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..64)

rcPortVrfCount		1.3.6.1.4.1.2272.1.4.10.1.1.99
The total number of VRFs this port is associated to.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcPortPcapTable		1.3.6.1.4.1.2272.1.4.10.2
Port pcap Table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPortPcapEntry

rcPortPcapEntry		1.3.6.1.4.1.2272.1.4.10.2.1
Entry containing pcap info. for a particular port
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPortPcapEntry

rcPortPcapIndex		1.3.6.1.4.1.2272.1.4.10.2.1.1
An index value that uniquely identifies a port. This value is similar to ifIndex in MIB2.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcPortPcapEnable		1.3.6.1.4.1.2272.1.4.10.2.1.2
To enable pcap for the port
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcPortPcapMode		1.3.6.1.4.1.2272.1.4.10.2.1.3
Mode in which pcap is enabled
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	tx(1), rx(2), both(3), rxFilter(4), txFilter(5), bothFilter(6)

rcPortPcapFilterListSize		1.3.6.1.4.1.2272.1.4.10.2.1.4
Used to indicate the number of filter list(s) that are assigned to this port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..128

rcPortPcapFilterList		1.3.6.1.4.1.2272.1.4.10.2.1.5
Used to indicate zero or more filter lists that are associated with this port for pcap. Each filter list identifier is stored as two bytes in this array starting from offset zero. Any unused bytes should be set to zero.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..256)

rcPortPcapAclFilterListSize		1.3.6.1.4.1.2272.1.4.10.2.1.6
Used to indicate the number of ACL filter(s) that are assigned to this port which has mirror set as global-action.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..128

rcPortPcapAclFilterList		1.3.6.1.4.1.2272.1.4.10.2.1.7
Used to indicate zero or more ACL filter lists that are associated with this port for pcap (has mirror set as global-action). Each ACL filter list identifier is stored as two bytes in this array starting from offset zero. Any unused bytes should be set to zero.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..256)

rcPortLock		1.3.6.1.4.1.2272.1.4.11
OBJECT IDENTIFIER

rcPortLockEnable		1.3.6.1.4.1.2272.1.4.11.1
Indicate whether the port lock feature is enabled.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcPortLockLockedPorts		1.3.6.1.4.1.2272.1.4.11.2
The set of ports that are administratively locked. Locked ports cannot be modified in anyway until the port is unlocked first.
Status: current	Access: read-write
OBJECT-TYPE
	PortSet

rcPortLacpTable		1.3.6.1.4.1.2272.1.4.10.4
Port LACP table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPortLacpEntry

rcPortLacpEntry		1.3.6.1.4.1.2272.1.4.10.4.1
Entry containing info. for a particular port
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPortLacpEntry

rcPortLacpAdminEnable		1.3.6.1.4.1.2272.1.4.10.4.1.1
Administratively enable/disable LACP on a port
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcPortLacpOperEnable		1.3.6.1.4.1.2272.1.4.10.4.1.2
Indicates if LACP is operationally enabled or disabled on a port
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcPortLacpFastPeriodicTime		1.3.6.1.4.1.2272.1.4.10.4.1.3
The number of miliseconds between periodic transmissions using Short Timeouts.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	200..20000

rcPortLacpSlowPeriodicTime		1.3.6.1.4.1.2272.1.4.10.4.1.4
The number of miliseconds between periodic transmissions using LONG Timeouts.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	10000..30000

rcPortLacpTimeoutScale		1.3.6.1.4.1.2272.1.4.10.4.1.5
Scalar value used to calculate timeout time from periodic time. Timeout = PeriodicTime * TimeoutScale
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..10

rcPortLacpAggrWaitTime		1.3.6.1.4.1.2272.1.4.10.4.1.6
The number of mili seconds to delay aggregation to allow multiple links to aggregate simultaneously.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	200..2000

rcPortLacpFastPeriodicTimeOper		1.3.6.1.4.1.2272.1.4.10.4.1.7
The operating value of fast periodic timer on the port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	200..20000

rcPortLacpSlowPeriodicTimeOper		1.3.6.1.4.1.2272.1.4.10.4.1.8
The operating value of slow periodic timer on the port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	10000..30000

rcPortLacpTimeoutScaleOper		1.3.6.1.4.1.2272.1.4.10.4.1.9
The operating value of timeout scale on the port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..10

rcPortLacpAggrWaitTimeOper		1.3.6.1.4.1.2272.1.4.10.4.1.10
The operating value of aggreagate wait time on port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	200..2000

rcPortVLacpTable		1.3.6.1.4.1.2272.1.4.10.5
Port Virtual LACP table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPortVLacpEntry

rcPortVLacpEntry		1.3.6.1.4.1.2272.1.4.10.5.1
Entry containing info. for a particular port
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPortVLacpEntry

rcPortVLacpAdminEnable		1.3.6.1.4.1.2272.1.4.10.5.1.1
Administratively enable/disable Virtual LACP on a port
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcPortVLacpOperEnable		1.3.6.1.4.1.2272.1.4.10.5.1.2
Indicates if Virtual LACP is operationally enabled or disabled on a port
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcPortVLacpFastPeriodicTimer		1.3.6.1.4.1.2272.1.4.10.5.1.3
The number of miliseconds between periodic transmissions using Short Timeouts
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	10..20000

rcPortVLacpSlowPeriodicTimer		1.3.6.1.4.1.2272.1.4.10.5.1.4
The number of miliseconds between periodic transmissions using LONG Timeouts.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	10000..30000

rcPortVLacpTimeout		1.3.6.1.4.1.2272.1.4.10.5.1.5
Timeout control value. Long or Short Timeout
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	short(1), long(2)

rcPortVLacpTimeoutScale		1.3.6.1.4.1.2272.1.4.10.5.1.6
Scalar value used to calculate timeout time from periodic time. Timeout = PeriodicTime * TimeoutScale
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..10

rcPortVLacpEtherType		1.3.6.1.4.1.2272.1.4.10.5.1.7
VLACP Protocol Identification. The id value is in Hex. The acceptable values for this MIB is 0x0 to 0xffff
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcPortVLacpEtherMacAddress		1.3.6.1.4.1.2272.1.4.10.5.1.8
Multicast Mac Address exclusively used for VLACPDU's
Status: current	Access: read-write
OBJECT-TYPE
	MacAddress

rcPortVLacpPortState		1.3.6.1.4.1.2272.1.4.10.5.1.9
Display the Vlacp Port State.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2)

rcPortVLacpFlapDetectEnable		1.3.6.1.4.1.2272.1.4.10.5.1.11
Administratively enable/disable VLACP flap detection on a port
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcPortVLacpFlapFrequency		1.3.6.1.4.1.2272.1.4.10.5.1.12
The number of VLACP Flaps on a port, that if they occure within rcPortVLacpFlapInterval seconds, the port is shutdown.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	3..30

rcPortVLacpFlapInterval		1.3.6.1.4.1.2272.1.4.10.5.1.13
The time inteval in seconds within which VLACP flaps on a port are monitored.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	10..600

rcPortVLacpTotalFlapCount		1.3.6.1.4.1.2272.1.4.10.5.1.14
Total Number of VLACP flaps detected on this port since either enabling VLACP or clearing the counter.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcPortVLacpFirstFlapTimeStamp		1.3.6.1.4.1.2272.1.4.10.5.1.15
Timestamp for the first VLACP flap detected on this port since either enabling VLACP or clearing the timer.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcPortVLacpLastFlapTimeStamp		1.3.6.1.4.1.2272.1.4.10.5.1.16
Timestamp for the latest VLACP flap detected on this port since either enabling VLACP or clearing the timer.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcPortVLacpFlapClearStats		1.3.6.1.4.1.2272.1.4.10.5.1.17
Clears all VLACP flap counters and timers.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcPortRemoteMirroringTable		1.3.6.1.4.1.2272.1.4.10.6
Port Remote Mirroring Table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPortRemoteMirroringEntry

rcPortRemoteMirroringEntry		1.3.6.1.4.1.2272.1.4.10.6.1
Entry containing remote mirroring info. for a particular port
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPortRemoteMirroringEntry

rcPortRemoteMirroringIndex		1.3.6.1.4.1.2272.1.4.10.6.1.1
An index value that uniquely identifies a port. This value is similar to ifIndex in MIB2.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcPortRemoteMirroringEnable		1.3.6.1.4.1.2272.1.4.10.6.1.2
To enable remote Mirroring for the port
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcPortRemoteMirroringMode		1.3.6.1.4.1.2272.1.4.10.6.1.3
Mode in which remote mirroring is enabled
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	source(1), termination(2)

rcPortRemoteMirroringSrcMac		1.3.6.1.4.1.2272.1.4.10.6.1.4
Source Mac of the remote mirrored packet. Remote mirroring packet will be send with this source mac address
Status: current	Access: read-write
OBJECT-TYPE
	MacAddress

rcPortRemoteMirroringDstMac		1.3.6.1.4.1.2272.1.4.10.6.1.5
Destination Mac of the remote mirrored packet. Packets will be bridged to this mac address. Remote mirroring packet will be send to this mac address
Status: current	Access: read-write
OBJECT-TYPE
	MacAddress

rcPortRemoteMirroringEtherType		1.3.6.1.4.1.2272.1.4.10.6.1.6
Ethertype of the remote mirrored packet. Packets will be send with this ethertype
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

rcPortRemoteMirroringVlanIdListSize		1.3.6.1.4.1.2272.1.4.10.6.1.7
Used to indicate the number of VLAN IDs that are assigned to this port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..2000

rcPortRemoteMirroringVlanIdList		1.3.6.1.4.1.2272.1.4.10.6.1.8
This field is used only if the port is assigned as remote mirroring termination port. Represents zero or more filter lists vlan in which the Destination Mac address resides. Each VLAN ID is stored as two bytes in this array starting from offset zero. Any unused bytes should be set to zero.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(4096)

rcPortRemoteMirroringRowStatus		1.3.6.1.4.1.2272.1.4.10.6.1.9
RowStatus
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcPortMgmtLinkTable		1.3.6.1.4.1.2272.1.4.10.8
Port card mgmt port link table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPortMgmtLinkEntry

rcPortMgmtLinkEntry		1.3.6.1.4.1.2272.1.4.10.8.1
Entry containing info. for a particular mgmt port in I/O card
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPortMgmtLinkEntry

rcPortMgmtLinkIndex		1.3.6.1.4.1.2272.1.4.10.8.1.1
IfIndex of the port.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcPortMgmtLinkDescr		1.3.6.1.4.1.2272.1.4.10.8.1.2
Port description
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..128)

rcPortMgmtLinkOperStatus		1.3.6.1.4.1.2272.1.4.10.8.1.3
admin status of the mgmt port
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2), unknown(3)

rcPortMgmtLinkAutoNegotiate		1.3.6.1.4.1.2272.1.4.10.8.1.4
Auto-negotiation status of the port
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcPortMgmtLinkDuplex		1.3.6.1.4.1.2272.1.4.10.8.1.5
duplex setting for the port
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	half(1), full(2)

rcPortMgmtLinkSpeed		1.3.6.1.4.1.2272.1.4.10.8.1.6
speed setting for this port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(0), mbps10(1), mbps100(2), mbps1000(3)

rcPortFlushMacTable		1.3.6.1.4.1.2272.1.4.10.11
Flush MAC entry on a port.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPortFlushMacEntry

rcPortFlushMacEntry		1.3.6.1.4.1.2272.1.4.10.11.1
Port mac flush table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPortFlushMacEntry

rcPortFlushMacPortNum		1.3.6.1.4.1.2272.1.4.10.11.1.1
Port number where the mac record exists.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..2147483647

rcPortFlushMacAddr		1.3.6.1.4.1.2272.1.4.10.11.1.2
Mac Address that needs to be removed.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(17)

rcPortFlushMacVlanId		1.3.6.1.4.1.2272.1.4.10.11.1.3
Vlan Id associated with the Mac Address.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..4094

rcChasAruMode		1.3.6.1.4.1.2272.1.4.12
The ARU mode the chassis is operating in.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	aruOne(1), aruTwo(2), aruThree(3)

rcChasQuidMode		1.3.6.1.4.1.2272.1.4.13
The Quid mode the chassis is operating in.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	quidMixed(1), quidTwo(2), quidThree(3), quidFour(4), quidFive(5)

rcChasEocModeAdminStatus		1.3.6.1.4.1.2272.1.4.14
Used to specify the Enforce Operational Configuration Mode(EOC) of the system. When a device is configured with hardware of different revisions, the system will initialize in some deterministic manner (e.g., the lowest common denominator that makes sense based on the hardware configuration). This is the 'default(0)' mode. The user can override this behavior by manually specifying the EOC Mode they would like.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	default(0), aru1Quid4(1), aru2Quid4(2), aru2Quid5(3), aru3Quid4(4), aru3Quid5(5)

rcChasEocModeOperStatus		1.3.6.1.4.1.2272.1.4.15
Used to indicate the Enforce Operational Configuration Mode(EOC) of the system.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	default(0), aru1Quid4(1), aru2Quid4(2), aru2Quid5(3), aru3Quid4(4), aru3Quid5(5)

rcChasBrouterPorts		1.3.6.1.4.1.2272.1.4.17
Used to indicate which ports in the system are configured as Brouter ports.
Status: current	Access: read-only
OBJECT-TYPE
	PortSet

rcChasGlobalFilterEnable		1.3.6.1.4.1.2272.1.4.18
Used to enable/disable global filters in the system. This variable is currently not supported.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcChasVlanBySrcMacEnable		1.3.6.1.4.1.2272.1.4.19
Used to enable/disable source MAC based VLANs in the system.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcChasDiffServEcnCompatibilityEnable		1.3.6.1.4.1.2272.1.4.20
Used to enable/disable the Explicit Congestion Notification(ECN) compatibility feature. When set to FALSE , the system will mask the ECN bits in the DS field while re-marking DSCP and will not match on ECN capable flows if filter is set on DSmatch. When set to TRUE, it will preserve the ECN bits in the DS field while re-marking and will match on full 8-bit DS field.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcChasNewEnhancedOperMode		1.3.6.1.4.1.2272.1.4.21
Enhanced operational mode.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcChasNewEMMode		1.3.6.1.4.1.2272.1.4.22
This configuration is for enabling/disabling 128K mode. The change will take effect upon reboot.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcChasEmModeError		1.3.6.1.4.1.2272.1.4.23
Used to indicate the Em-mode error status
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), non128KCardOffLine(2), checkSlaveConfigNResetForEmMMode(3), mismatchResetForEmMode(4), mismatchEmModeMasterSlave(5), incompatMasterResetForEmMode(6), putSlaveOffEmImcompat(7), slave8690EmIncompatGoingOffline(8), cpu8690DisableEm(9)

rcChasEnhancedOperMode		1.3.6.1.4.1.2272.1.4.24
Enhanced Operational mode the switch currently has booted and will remain the same until the next reboot.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcChasEMMode		1.3.6.1.4.1.2272.1.4.25
EM mode the switch currently has booted and will remain the same until the next reboot.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcChasFtpDaemonInSecondaryCpu		1.3.6.1.4.1.2272.1.4.26
Used to enable/disable FTP daemon in 2nd cpu.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcChasSmltOnSingleCpEnable		1.3.6.1.4.1.2272.1.4.27
Enable SMLT on single CP feature in the switch
Status: deprecated	Access: read-write
OBJECT-TYPE
	TruthValue

rcChasNewVlanOptmMode		1.3.6.1.4.1.2272.1.4.28
Vlan Optimization mode.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcChasVlanOptmMode		1.3.6.1.4.1.2272.1.4.29
Vlan Optimization mode the switch currently has booted and will remain the same until the next reboot.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcLaunchPad		1.3.6.1.4.1.2272.1.4.30
OBJECT IDENTIFIER

rcLaunchPadTable		1.3.6.1.4.1.2272.1.4.30.1
Launch Pad in a chassis table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcLaunchPadEntry

rcLaunchPadEntry		1.3.6.1.4.1.2272.1.4.30.1.1
Entry containing Launch pad card info
Status: current	Access: not-accessible
OBJECT-TYPE
	RcLaunchPadEntry

rcLaunchPadSlotId		1.3.6.1.4.1.2272.1.4.30.1.1.1
Launch Pad card id
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

rcLaunchPadMiniSlotId		1.3.6.1.4.1.2272.1.4.30.1.1.2
Launch pad mini card id.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

rcLaunchPadAppType		1.3.6.1.4.1.2272.1.4.30.1.1.3
Launch Pad application type.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), firewall(2), ssl(3), ids(4), vpn(5), tps(6)

rcLaunchPadMiniSlotIp		1.3.6.1.4.1.2272.1.4.30.1.1.4
Launch Pad mini card's ip address.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcLaunchPadNaapLpState		1.3.6.1.4.1.2272.1.4.30.1.1.5
Enable/Disable naap Ip state.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcLaunchPadMiniSlotSwVersion		1.3.6.1.4.1.2272.1.4.30.1.1.6
Launch Pad mini card's SW version.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

rcLaunchPadHWType		1.3.6.1.4.1.2272.1.4.30.1.1.7
for identifying the ISD
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	fw(1), tps(2), none(3)

rcLaunchPadClusterTable		1.3.6.1.4.1.2272.1.4.30.2
Launch Pad Cluster Table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcLaunchPadClusterEntry

rcLaunchPadClusterEntry		1.3.6.1.4.1.2272.1.4.30.2.1
Entry containing Launch pad cluster info
Status: current	Access: not-accessible
OBJECT-TYPE
	RcLaunchPadClusterEntry

rcLaunchPadClusterId		1.3.6.1.4.1.2272.1.4.30.2.1.1
Launch pad cluster id.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..64

rcLaunchPadClusterType		1.3.6.1.4.1.2272.1.4.30.2.1.2
Launch Pad cluster type.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	firewall(1), ssl(2), is(3), vpn(4)

rcLaunchPadClusterSize		1.3.6.1.4.1.2272.1.4.30.2.1.3
Launch pad cluster size.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..16

rcLaunchPadClusterMembers		1.3.6.1.4.1.2272.1.4.30.2.1.4
Launch pad cluster members
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..32)

rcLaunchPadClusterRowStatus		1.3.6.1.4.1.2272.1.4.30.2.1.5
Launch pad cluster Row Status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcLaunchPadClusterMgmtVlan		1.3.6.1.4.1.2272.1.4.30.2.1.6
Launch pad cluster management vlan Id.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..4094

rcLaunchPadClusterSyncVlan		1.3.6.1.4.1.2272.1.4.30.2.1.7
Launch pad cluster cp sync vlan Id.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..4094

rcLaunchPadClusterTpsSize		1.3.6.1.4.1.2272.1.4.30.2.1.8
Launch pad cluster TPS size.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..2

rcLaunchPadClusterTpsMembers		1.3.6.1.4.1.2272.1.4.30.2.1.9
Launch pad cluster TPS members
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..32)

rcLaunchPadClusterPortMember		1.3.6.1.4.1.2272.1.4.30.2.1.10
IS cluster user port list that needs to be monitored
Status: current	Access: read-write
OBJECT-TYPE
	PortSet

rcChasNaapEnable		1.3.6.1.4.1.2272.1.4.31
To enable/disbale to napp feature.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcChasGlobalFilterOrderingEnable		1.3.6.1.4.1.2272.1.4.32
Global Filter ordering in the system.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcChasNewGlobalFilterOrderingEnable		1.3.6.1.4.1.2272.1.4.33
This configuration is for enabling/disabling global filter ordering. The change will take effect upon reboot.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcChasWsmDirectMode		1.3.6.1.4.1.2272.1.4.34
This is for enabling/disabling configuration of same community strings on the WSM and 8600/8800. This is for allowing users to connect directly via SNMP to the WSM blade.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcChasRspMode		1.3.6.1.4.1.2272.1.4.35
This configuration is for enabling/disabling 256K mode. The change will take effect upon reboot.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcChasRspOperMode		1.3.6.1.4.1.2272.1.4.36
R-mode the switch currently has booted and will remain the same until the next reboot.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcChasRspModeError		1.3.6.1.4.1.2272.1.4.37
Used to indicate the r-mode error status
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), non256KCardOffLine(2)

rcChasMcastCheckPktEnable		1.3.6.1.4.1.2272.1.4.40
Used to enable/disable Multicast check packet in the system. This change will take effect upon reboot.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcChasSystemMonitorEnable		1.3.6.1.4.1.2272.1.4.41
Enable/Disable System monitoring in the switch
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcChasSysMonMonitoringEnable		1.3.6.1.4.1.2272.1.4.42
Dyanamically Enable/Disable SystemMonitor monitoring engine in the switch
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcChasSysMonDetectionTime		1.3.6.1.4.1.2272.1.4.43
System Monitor Detection time in seconds
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	10..600

rcChasNewMulticastResourceReservation		1.3.6.1.4.1.2272.1.4.44
Used to reserve MGIDs for IP Multicast. The change will take effect upon reboot.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	64..4083

rcChasMulticastResourceReservation		1.3.6.1.4.1.2272.1.4.45
MGIDs the switch currently has reserved for IP Multicast; will remain the same until the next reboot.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	64..4083

rcChasNewMaxVlanResourceReservation		1.3.6.1.4.1.2272.1.4.46
A mode where all MGIDs are reserved for VLAN use only; no IPMC. The change will take effect upon reboot.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcChasMaxVlanResourceReservation		1.3.6.1.4.1.2272.1.4.47
Tells if all MGIDs are reserved for VLAN use. Will remain the same until the next reboot.
Status: current	Access: read-only
OBJECT-TYPE
	EnableValue

rcChasMgidUsageVlanCurrent		1.3.6.1.4.1.2272.1.4.48
Number of MGIDs currently used for VLAN, including SMLT
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..4084

rcChasMgidUsageVlanRemaining		1.3.6.1.4.1.2272.1.4.49
Number of MGIDs remaining allocated for VLAN
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..4084

rcChasMgidUsageMulticastCurrent		1.3.6.1.4.1.2272.1.4.50
Number of MGIDs currently used for IPMC
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..4083

rcChasMgidUsageMulticastRemaining		1.3.6.1.4.1.2272.1.4.51
Number of MGIDs remaining allocated for IPMC
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..4083

rcChasPowerManagementEnable		1.3.6.1.4.1.2272.1.4.52
Turn on or off Chassis Power Management. The configuration will take effect upon reboot.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcChasForceTopologyIpFlagEnable		1.3.6.1.4.1.2272.1.4.53
Used to enable/disable flag which is used to set the CLIP-ip as topology ip
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcChasCircuitlessIpId		1.3.6.1.4.1.2272.1.4.54
The Clip-Id set by the user to be used as Topology-ip
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..256

rcChasPowerManagementOriginalEnable		1.3.6.1.4.1.2272.1.4.55
On or off value of Chassis Power Management which the switch has currently booted. It will remain the same until the next reboot.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcChasPowerManagementFanCheck		1.3.6.1.4.1.2272.1.4.56
Turn on or off the Fan Check functionility of Chassis Power Management. The value takes effect only on reboot.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcChasPowerManagementFanCheckOriginalState		1.3.6.1.4.1.2272.1.4.57
The on or off value of fan check which the switch has booted with. The value does not take effect till the next reboot.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcChasTakeIOCardOfflineEnable		1.3.6.1.4.1.2272.1.4.61
Enable/Disable IO Card to go offline when F2E sees excessive resets.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcChasAutoResetFabricEnable		1.3.6.1.4.1.2272.1.4.62
Enable/Disable fabric to be reset automatically on fab mem full error.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcAgentTable		1.3.6.1.4.1.2272.1.4.16
Agents in a chassis table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcAgentEntry

rcAgentEntry		1.3.6.1.4.1.2272.1.4.16.1
Entry containing info. for a particular agent
Status: current	Access: not-accessible
OBJECT-TYPE
	RcAgentEntry

rcAgentId		1.3.6.1.4.1.2272.1.4.16.1.1
entry id
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

rcAgentSlot		1.3.6.1.4.1.2272.1.4.16.1.2
slot agent is in.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcAgentIpAddr		1.3.6.1.4.1.2272.1.4.16.1.3
agent's ip address.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcMirrorSaveConfig		1.3.6.1.4.1.2272.1.5.1
Control whether Mirror configuration information should be saved to NVRAM so mirror settings can be automatically reinstalled after a system reboot. Setting rcMirrorSaveConfig to true does not immediately save the configuration information. The save happens when the rcSysAction variable is set to 'saveToNVRAM(4)'.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcMirrorByPort		1.3.6.1.4.1.2272.1.5.2
OBJECT IDENTIFIER

rcMirrorByPortEnable		1.3.6.1.4.1.2272.1.5.2.1
Used to indicate whether the mirror by port feature is active. The system can only support mirroring on two ports. When this feature is active, all packets received on the port(s) specified by rcMirrorSrcPortOne and/or rcMirrorSrcPortTwo are copied to rcMirrorDstPort. The mirroring operation is non-intrusive.
Status: deprecated	Access: read-write
OBJECT-TYPE
	TruthValue

rcMirrorByPortMirrorPort		1.3.6.1.4.1.2272.1.5.2.2
The ifIndex of the port to forward mirrored frames to.
Status: deprecated	Access: read-write
OBJECT-TYPE
	InterfaceIndex

rcMirrorByPortEnableMirroredPortOne		1.3.6.1.4.1.2272.1.5.2.3
Used to indicate whether the port specified in rcMirrorByPortMirroredPortOne should be mirrored.
Status: deprecated	Access: read-write
OBJECT-TYPE
	TruthValue

rcMirrorByPortMirroredPortOne		1.3.6.1.4.1.2272.1.5.2.4
The ifIndex of the port to be mirrored. That is, traffic received on this port will be sent to the mirror port.
Status: deprecated	Access: read-write
OBJECT-TYPE
	InterfaceIndex

rcMirrorByPortEnableMirroredPortTwo		1.3.6.1.4.1.2272.1.5.2.5
Used to indicate whether the port specified in rcMirrorByPortMirroredPortTwo should be mirrored.
Status: deprecated	Access: read-write
OBJECT-TYPE
	TruthValue

rcMirrorByPortMirroredPortTwo		1.3.6.1.4.1.2272.1.5.2.6
The ifIndex of the port to be mirrored. That is, traffic received on this port will be sent to the mirror port.
Status: deprecated	Access: read-write
OBJECT-TYPE
	InterfaceIndex

rcIsolateUnconfigPorts		1.3.6.1.4.1.2272.1.6.1
Used to indicate whether ports that are unconfigured should be assigned to the 'isolated' VLAN. Ports assigned to the 'isolated' VLAN can only communicate with the CP port. If this option is not specified, unconfigured ports will be assigned to the 'default' VLAN
Status: deprecated	Access: read-only
OBJECT-TYPE
	TruthValue

rcUseFactorySettings		1.3.6.1.4.1.2272.1.6.2
Used to indicate whether the system should ignore the configuration information stored in NVRAM when the system is booted.
Status: deprecated	Access: read-only
OBJECT-TYPE
	TruthValue

rcHighPriorityMode		1.3.6.1.4.1.2272.1.6.3
Used to indicate whether the system is configured to operate in a high priority mode. The switch can operate in either a 'best effort' or 'high priority' mode. In the 'best effort' setting, the maximum queue thresholds for the QUIDs are set to 768/768 buffers. In the 'high priority' mode the setting is 512/768. This means that in 'high priority' mode the normal priority queue can't have more than 512 buffers, while the high priority queue can have up to 768.
Status: deprecated	Access: read-only
OBJECT-TYPE
	TruthValue

rcTblRmonStatSize		1.3.6.1.4.1.2272.1.7.1
Used to indicate the current size of the RMON Statistic table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcTblRmonHistoryControlSize		1.3.6.1.4.1.2272.1.7.2
Used to indicate the current size of the RMON History Control table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcTblRmonHistoryEnetSize		1.3.6.1.4.1.2272.1.7.3
Used to indicate the current size of the RMON History Ethernet table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcTblRmonAlarmSize		1.3.6.1.4.1.2272.1.7.4
Used to indicate the current size of the RMON Alarm table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcTblRmonEventSize		1.3.6.1.4.1.2272.1.7.5
Used to indicate the current size of the RMON Event table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcTblRmonLogSize		1.3.6.1.4.1.2272.1.7.6
Used to indicate the current size of the RMON Log table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcTblArTblSize		1.3.6.1.4.1.2272.1.7.7
Used to indicate the size of the Address Translation (AR) table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcTblArFree		1.3.6.1.4.1.2272.1.7.8
Used to indicate the number of free entries that are available in the Address Translation (AR) table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcTblArNoSpace		1.3.6.1.4.1.2272.1.7.9
Used to indicate the number of entries that could not be added to the Address Translation (AR) table due to lack of space.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcTblArAdded		1.3.6.1.4.1.2272.1.7.10
Used to indicate the number of entries added to the Address Translation (AR) table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcTblArDeleted		1.3.6.1.4.1.2272.1.7.11
Used to indicate the number of entries deleted to the Address Translation (AR) table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcTblArMacAdded		1.3.6.1.4.1.2272.1.7.12
Used to indicate the number of MAC entries added to the Address Translation (AR) table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcTblArMacDeleted		1.3.6.1.4.1.2272.1.7.13
Used to indicate the number of MAC entries deleted to the Address Translation (AR) table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcTblArMacMoved		1.3.6.1.4.1.2272.1.7.14
Used to indicate the number of MAC entries moved in the Address Translation (AR) table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcTblArIpAdded		1.3.6.1.4.1.2272.1.7.15
Used to indicate the number of IP entries added to the Address Translation (AR) table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcTblArIpDeleted		1.3.6.1.4.1.2272.1.7.16
Used to indicate the number of IP entries deleted to the Address Translation (AR) table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcTblArMcastTblSize		1.3.6.1.4.1.2272.1.7.17
Used to indicate the size of the Multicast Address Translation (AR) table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcTblArFreeMcastGroups		1.3.6.1.4.1.2272.1.7.18
Used to indicate the number of free multicast groups availabe in the Address Translation (AR) table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcTblArIpMcastAdded		1.3.6.1.4.1.2272.1.7.19
Used to indicate the number of Ip multicast entries that are added to the Address Translation (AR) table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcTblArIpMcastDeleted		1.3.6.1.4.1.2272.1.7.20
Used to indicate the number of Ip multicast entries that are deleted from the Address Translation (AR) table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcTblArVlanByPortAdded		1.3.6.1.4.1.2272.1.7.21
Used to indicate the number of VLAN by port entries that are added to the Address Translation (AR) table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcTblArVlanByPortDeleted		1.3.6.1.4.1.2272.1.7.22
Used to indicate the number of VLAN by port entries that are deleted from the Address Translation (AR) table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcTblArVlanByProtocolAdded		1.3.6.1.4.1.2272.1.7.23
Used to indicate the number of Vlans by Protocol Type entries that are added to the Address Translation (AR) table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcTblArVlanByProtocolDeleted		1.3.6.1.4.1.2272.1.7.24
Used to indicate the number of Vlans by Protocol Type entries that are deleted from the Address Translation (AR) table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcTblArVlanByIpSubnetAdded		1.3.6.1.4.1.2272.1.7.25
Used to indicate the number of VLAN by Ip entries that are added to the Address Translation (AR) table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcTblArVlanByIpSubnetDeleted		1.3.6.1.4.1.2272.1.7.26
Used to indicate the number of VLAN by Ip entries that are deleted from the Address Translation (AR) table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcTblArIpSubnetsAdded		1.3.6.1.4.1.2272.1.7.27
Used to indicate the number of Ip subnet entries that are added to the Address Translation (AR) table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcTblArIpSubnetsDeleted		1.3.6.1.4.1.2272.1.7.28
Used to indicate the number of Ip subnet entries that are deleted from the Address Translation (AR) table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcTblArRsvpsAdded		1.3.6.1.4.1.2272.1.7.29
Used to indicate the number of RSVP entries that are added to the Address Translation (AR) table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcTblArRsvpsDeleted		1.3.6.1.4.1.2272.1.7.30
Used to indicate the number of RSVP entries that are deleted from the Address Translation (AR) table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcTblBrdgFdbSize		1.3.6.1.4.1.2272.1.7.31
Used to indicate the number of entries in the dot1d forwarding database table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcTblBrdgStaticSize		1.3.6.1.4.1.2272.1.7.32
Used to indicate the number of entries in the dot1d Static Address Filtering table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcTblIpAddrSize		1.3.6.1.4.1.2272.1.7.33
Used to indicate the number of entries in the IP Address table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcTblIpForwardingSize		1.3.6.1.4.1.2272.1.7.34
Used to indicate the number of entries in the IP Forwarding/Best Route table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcTblIpNetToMediaSize		1.3.6.1.4.1.2272.1.7.35
Used to indicate the number of entries in the IP Net-to-media table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcTblIpBestPlusAltRouteSize		1.3.6.1.4.1.2272.1.7.36
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcTblIpBestPathSize		1.3.6.1.4.1.2272.1.7.37
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcTblIpBestPlusAltPathSize		1.3.6.1.4.1.2272.1.7.38
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpConf		1.3.6.1.4.1.2272.1.8.1
OBJECT IDENTIFIER

rcIpConfTable		1.3.6.1.4.1.2272.1.8.1.1
A table used to maintain IP routing information for a particular interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpConfEntry

rcIpConfEntry		1.3.6.1.4.1.2272.1.8.1.1.1
Entry containing IP routing information. An entry is automatically created in this table when routing is enabled for an interface -or- when an ip address is configured on an interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpConfEntry

rcIpConfIfIndex		1.3.6.1.4.1.2272.1.8.1.1.1.1
An unique value to identify a physical interface or a logical interface (VLAN).
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndexOrZero	0..6142

rcIpConfAdvertDefRte		1.3.6.1.4.1.2272.1.8.1.1.1.2
Used to indicate whether this interface should advertize a RIP default route.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpConfAcceptDefRte		1.3.6.1.4.1.2272.1.8.1.1.1.3
Used to indicate whether this interface should accept a RIP default route.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpConfRowStatus		1.3.6.1.4.1.2272.1.8.1.1.1.4
Row status for this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpConfRipEnable		1.3.6.1.4.1.2272.1.8.1.1.1.5
Enable or disable RIP routing on the specified interface.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpConfOspfEnable		1.3.6.1.4.1.2272.1.8.1.1.1.6
Enable or disable OSPF routing on the specified interface.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpConfIgmpEnable		1.3.6.1.4.1.2272.1.8.1.1.1.7
Enable or disable IGMP on the specified interface.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpConfAddrAssigned		1.3.6.1.4.1.2272.1.8.1.1.1.8
Indicate whether IpAddress has been assigned for this interface.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcIpConfDhcpEnable		1.3.6.1.4.1.2272.1.8.1.1.1.9
Enable or disable DHCP on the specified interface.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpConfTriggeredUpdateEnable		1.3.6.1.4.1.2272.1.8.1.1.1.10
Used to indicate whether the RIP triggered update feature should be enabled on this interface.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpConfAutoAggrerateEnable		1.3.6.1.4.1.2272.1.8.1.1.1.11
Used to indicate whether the auto aggregation feature should be enabled on this interface.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpConfGenerateDefaultRoute		1.3.6.1.4.1.2272.1.8.1.1.1.12
Used to indicate whether to generate a default RIP route on this interface.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpConfAdvertiseWhenDown		1.3.6.1.4.1.2272.1.8.1.1.1.13
The value is used indicated whether vlan state change should be notified to layer 3 or not, provided the vlan is configured as routable interface. Also used for single routable ports, in that case the criteria for state is PortOperStatus. Vlan is considered as UP if atleast one member of the port based vlan has link up, or atleast one port member of the policy based has an entry in the MGID or atleast one static member of the policy based vlan has link up. Otherwise, vlan is considered as DOWN. If the value is 'true' then the interface state change will not be notified to layer 3. (i.e., it always stays up). If the value is 'false' then the vlan state change will be notified to layer 3 so that IP related status reflects routable interface state.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpConfDirectBroadcastEnable		1.3.6.1.4.1.2272.1.8.1.1.1.14
Used to indicate whether this interface should forward direct broadcast traffic
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpConfRipInPolicy		1.3.6.1.4.1.2272.1.8.1.1.1.15
Used to indicate whether this interface should advertize a RIP default route.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..64)

rcIpConfRipOutPolicy		1.3.6.1.4.1.2272.1.8.1.1.1.16
Used to indicate whether this interface should accept a RIP default route.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..64)

rcIpConfOspfIfType		1.3.6.1.4.1.2272.1.8.1.1.1.17
OSPF Interface Type.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	broadcast(1), nbma(2), pointToPoint(3), pointToMultipoint(5), passive(99)

rcIpConfRipCost		1.3.6.1.4.1.2272.1.8.1.1.1.18
Used to indicate the rip cost for this interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..15

rcIpConfRipHolddown		1.3.6.1.4.1.2272.1.8.1.1.1.19
Used to indicate the rip holddown timer for this interface
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..360

rcIpConfRipTimeout		1.3.6.1.4.1.2272.1.8.1.1.1.20
Used to indicate the rip timeout interval for this interface
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	15..259200

rcIpConfRsmltEnable		1.3.6.1.4.1.2272.1.8.1.1.1.21
Used to enable Route Smlt feature.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpConfReversePathCheckEnable		1.3.6.1.4.1.2272.1.8.1.1.1.22
Used to indicate whether this interface should perform Reverse Path Check
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpConfReversePathCheckMode		1.3.6.1.4.1.2272.1.8.1.1.1.23
Reverse Path Checking mode.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	exist-only(1), strict(2)

rcIpConfIsisEnable		1.3.6.1.4.1.2272.1.8.1.1.1.24
Enable/disable ISIS protocol for this IP entry
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpConfBfdEnable		1.3.6.1.4.1.2272.1.8.1.1.1.25
Enable or disable BFD on the specified interface.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcIpConfIpVpnLiteEnable		1.3.6.1.4.1.2272.1.8.1.1.1.26
Enable or disable ipvpn-lite capability on the specified circuitless ip interface.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcIpConfOspfTable		1.3.6.1.4.1.2272.1.8.1.2
A table used to maintain OSPF information for a particular interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpConfOspfEntry

rcIpConfOspfEntry		1.3.6.1.4.1.2272.1.8.1.2.1
Entry containing OSPF information. An entry is automatically created in this table when routing is enabled for an interface -or- when an ip address is configured on an interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpConfOspfEntry

rcIpConfOspfIfIndex		1.3.6.1.4.1.2272.1.8.1.2.1.1
An unique value to identify a physical interface or a logical interface (VLAN).
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndexOrZero	0..6142

rcIpConfOspfRtrPriority		1.3.6.1.4.1.2272.1.8.1.2.1.2
The priority of this interface. Used in multi- access networks, this field is used in the designated router election algorithm. The value 0 signifies that the router is not eligible to become the designated router on this particular network. In the event of a tie in this value, routers will use their router id as a tie breaker.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..FF

rcIpConfOspfMetric		1.3.6.1.4.1.2272.1.8.1.2.1.3
The metric for this type of service (TOS) on this interface. The default value of the TOS 0 Metric is (10^9 / ifSpeed). The value FFFF means 'no route via this TOS'. A value of 0 means the interface speed (rcIpConfOspfDefaultMetric) will be used as metric value, when the state of the interface is up.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..FFFF

rcIpConfOspfAuthKey		1.3.6.1.4.1.2272.1.8.1.2.1.4
The Authentication Key. If the Area's Authorization Type is simplePassword, and the key length is shorter than 8 octets, the agent will left adjust and zero fill to 8 octets. Note that unauthenticated interfaces need no authentication key, and simple password authen- tication cannot use a key of more than 8 oc- tets. Larger keys are useful only with authen- tication mechanisms not specified in this docu- ment. When read, ospfIfAuthKey always returns an Octet String of length zero.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..8)

rcIpConfOspfRowStatus		1.3.6.1.4.1.2272.1.8.1.2.1.5
Row status for this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpConfOspfHelloInterval		1.3.6.1.4.1.2272.1.8.1.2.1.6
The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for all routers attached to a common network.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..FFFF

rcIpConfOspfRtrDeadInterval		1.3.6.1.4.1.2272.1.8.1.2.1.7
The number of seconds that a router's Hello packets have not been seen before it's neighbors declare the router down. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common network.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..7FFFFFFF

rcIpConfOspfIfAreaId		1.3.6.1.4.1.2272.1.8.1.2.1.8
A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0.0.0.0 is used for the OSPF backbone.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcIpConfOspfAuthType		1.3.6.1.4.1.2272.1.8.1.2.1.9
The authentication type specified for an interface. Additional authentication types may be assigned locally.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), simplePassword(1), md5(2)

rcIpConfOspfPollInterval		1.3.6.1.4.1.2272.1.8.1.2.1.10
OSPF NBMA Interface Poll Interval.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..2147483647

rcIpConfOspfIfMtuIgnore		1.3.6.1.4.1.2272.1.8.1.2.1.11
Mtu-ignore flag is for ignoring the mtu checking in ospf bdb
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

rcIpConfOspfBfdEnable		1.3.6.1.4.1.2272.1.8.1.2.1.12
Used to enable/disable BFD for OSPF.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpConfOspfDefaultMetric		1.3.6.1.4.1.2272.1.8.1.3
OBJECT IDENTIFIER

rcIpConfOspfDefaultMetric10MegPort		1.3.6.1.4.1.2272.1.8.1.3.1
Used to indicate the cost associated with 10Meg Interface(Port).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..FFFF

rcIpConfOspfDefaultMetric100MegPort		1.3.6.1.4.1.2272.1.8.1.3.2
Used to indicate the cost associated with 100Meg Interface(Port).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..FFFF

rcIpConfOspfDefaultMetric1000MegPort		1.3.6.1.4.1.2272.1.8.1.3.3
Used to indicate the cost associated with 1000Meg Interface(Port).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..FFFF

rcIpConfOspfDefaultMetric10000MegPort		1.3.6.1.4.1.2272.1.8.1.3.4
Used to indicate the cost associated with 10000Meg Interface(Port).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..FFFF

rcIpConfOspf		1.3.6.1.4.1.2272.1.8.1.4
OBJECT IDENTIFIER

rcIpConfOspfTrapEnable		1.3.6.1.4.1.2272.1.8.1.4.1
Used to indicate whether Ospf Traps should be sent.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpConfOspfAutoVirtLinkEnable		1.3.6.1.4.1.2272.1.8.1.4.2
Used to indicate whether auto virtual link creation is enabled or not. If set to true OSPF will create virtual links between ABRs whether it is needed or not, but adjacency will established only when one of the ABR losses connection to backbone area. If set to false then it is user resposibity to create virtual link whenever needed.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpConfOspfSpfHoldDownTime		1.3.6.1.4.1.2272.1.8.1.4.3
The SPF Hold Down Timer value. The SPF will run at most once per hold down timer value.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	3..60

rcIpConfOspfAction		1.3.6.1.4.1.2272.1.8.1.4.4
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), runSpf(1)

rcIpConfOspfRfc1583Compatibility		1.3.6.1.4.1.2272.1.8.1.4.5
Controls the preference rules used when choosing among multiple AS-External-LSAs advertising the same destination. When this is enabled, the preference rule will be same as specified by RFC1583. When disabled, the new preference rule as described in RFC2328 will be applicable, which potentially prevents the routing loops when AS-External-LSAs for the same destination have been originated from different areas.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpConfGlobal		1.3.6.1.4.1.2272.1.8.1.6
OBJECT IDENTIFIER

rcIpConfGlobalRipHoldDownTime		1.3.6.1.4.1.2272.1.8.1.6.1
Used to set the system-wide RIP hold down time in seconds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..360

rcIpConfGlobalIcmpNetUnreach		1.3.6.1.4.1.2272.1.8.1.6.2
Used to set the icmp net unreach feature enable/disable.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpConfGlobalEcmpEnable		1.3.6.1.4.1.2272.1.8.1.6.3
Used to set the ecmp enable/disable.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpConfGlobalEcmpMaxPath		1.3.6.1.4.1.2272.1.8.1.6.4
Used to globally configure maximum ECMP paths number.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..8

rcIpConfGlobalAlternativeEnable		1.3.6.1.4.1.2272.1.8.1.6.5
Used to globally configure alternative enable.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpConfGlobalRouteDiscoveryEnable		1.3.6.1.4.1.2272.1.8.1.6.6
Enable/disable ICMP Route Discovery feature
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpConfGlobalRipTimeOutInterval		1.3.6.1.4.1.2272.1.8.1.6.8
Rip TimeOut Interval in seconds
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	15..259200

rcIpConfGlobalRipDefImportMetric		1.3.6.1.4.1.2272.1.8.1.6.9
Rip def import metric
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..15

rcIpConfGlobalEcmp1PathList		1.3.6.1.4.1.2272.1.8.1.6.10
Routes to networks specified in this prefix-list can have upto 1 ECMP path, irrespective of ecmp-max-path configuration
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rcIpConfGlobalEcmp2PathList		1.3.6.1.4.1.2272.1.8.1.6.11
Routes to networks specified in this prefix-list can have upto 2 ECMP path, irrespective of ecmp-max-path configuration.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rcIpConfGlobalEcmp3PathList		1.3.6.1.4.1.2272.1.8.1.6.12
Routes to networks specified in this prefix-list can have upto 3 ECMP path, irrespective of ecmp-max-path configuration.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rcIpConfGlobalEcmp4PathList		1.3.6.1.4.1.2272.1.8.1.6.13
Routes to networks specified in this prefix-list can have upto 4 ECMP path, irrespective of ecmp-max-path configuration.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rcIpConfGlobalEcmpPathListApply		1.3.6.1.4.1.2272.1.8.1.6.14
This is to apply any changes in ECMP path list configuration or in the prefix-lists configured to be used as path list
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpConfGlobalIcmpRedirectMsg		1.3.6.1.4.1.2272.1.8.1.6.15
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpConfGlobalArpThreshold		1.3.6.1.4.1.2272.1.8.1.6.17
Defines the maximum number of outstanding arp request a switch can generate.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	50..1000

rcIpConfGlobalAllowMoreSpecificNonLocalRouteEnable		1.3.6.1.4.1.2272.1.8.1.6.18
Used to determine whether more specific non local routes will go into the routing table.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpConfGlobalUdpCheckSumEnable		1.3.6.1.4.1.2272.1.8.1.6.19
Enable/disable UDP checksum calculation
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpConfGlobalSuperNetEnable		1.3.6.1.4.1.2272.1.8.1.6.20
Used to globally enable Supernetting/ CIDR routing for IP
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpConfOspfAreaTable		1.3.6.1.4.1.2272.1.8.1.7
A table used to maintain OSPF information for a particular Area.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpConfOspfAreaEntry

rcIpConfOspfAreaEntry		1.3.6.1.4.1.2272.1.8.1.7.1
Entry containing OSPF Area configuration information. An entry is automatically created in this table when an area is configured through ospfAreaTable in (rfc1253rcc.mib).
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpConfOspfAreaEntry

rcIpConfOspfAreaId		1.3.6.1.4.1.2272.1.8.1.7.1.1
An unique value to identify an area. Area ID 0.0.0.0 is used for the OSPF backbone.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpConfOspfAreaImportSummary		1.3.6.1.4.1.2272.1.8.1.7.1.2
The area's support for importing Summary advertisements into a stub area. This field should be used only if ospfImportASExtern is set to FALSE
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpConfOspfAreaActiveIfCount		1.3.6.1.4.1.2272.1.8.1.7.1.3
This variable displays the number of active interfaces configured in this area. An area cannot be deleted if this value is > 0.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpConfV2Table		1.3.6.1.4.1.2272.1.8.1.8
A table used to maintain IP routing information for a particular interface.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpConfV2Entry

rcIpConfV2Entry		1.3.6.1.4.1.2272.1.8.1.8.1
Entry containing IP routing information. An entry is automatically created in this table when routing is enabled for an interface -or- when an ip address is configured on an interface.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	RcIpConfV2Entry

rcIpConfV2Index		1.3.6.1.4.1.2272.1.8.1.8.1.1
An unique value to identify a physical interface or a logical interface (VLAN).
Status: deprecated	Access: read-only
OBJECT-TYPE
	InterfaceIndexOrZero	0..6142

rcIpConfV2Addr		1.3.6.1.4.1.2272.1.8.1.8.1.2
Ip interface address.
Status: deprecated	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpConfV2RowStatus		1.3.6.1.4.1.2272.1.8.1.8.1.3
Row status for this entry.
Status: deprecated	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpConfV2AdvertDefRte		1.3.6.1.4.1.2272.1.8.1.8.1.4
Used to indicate whether this interface should advertize a RIP default route.
Status: deprecated	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpConfV2AcceptDefRte		1.3.6.1.4.1.2272.1.8.1.8.1.5
Used to indicate whether this interface should accept a RIP default route.
Status: deprecated	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpConfV2RipEnable		1.3.6.1.4.1.2272.1.8.1.8.1.6
Enable or disable RIP routing on the specified interface.
Status: deprecated	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpConfV2OspfEnable		1.3.6.1.4.1.2272.1.8.1.8.1.7
Enable or disable OSPF routing on the specified interface.
Status: deprecated	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpConfV2IgmpEnable		1.3.6.1.4.1.2272.1.8.1.8.1.8
Enable or disable IGMP on the specified interface.
Status: deprecated	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpConfV2AddrAssigned		1.3.6.1.4.1.2272.1.8.1.8.1.9
Indicate whether IpAddress has been assigned for this interface.
Status: deprecated	Access: read-only
OBJECT-TYPE
	TruthValue

rcIpConfV2TriggeredUpdateEnable		1.3.6.1.4.1.2272.1.8.1.8.1.10
Used to indicate whether the RIP triggered update feature should be enabled on this interface.
Status: deprecated	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpConfV2RipAutoAggrerateEnable		1.3.6.1.4.1.2272.1.8.1.8.1.11
Used to indicate whether the auto aggregation feature should be enabled on this interface.
Status: deprecated	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpConfV2RipGenerateDefaultRoute		1.3.6.1.4.1.2272.1.8.1.8.1.12
Used to indicate whether to generate a default RIP route on this interface.
Status: deprecated	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpConfV2AdvertiseWhenDown		1.3.6.1.4.1.2272.1.8.1.8.1.13
The value is used indicated whether vlan state change should be notified to layer 3 or not, provided the vlan is configured as routable interface. Also used for single routable ports, in that case the criteria for state is PortOperStatus. Vlan is considered as UP if atleast one member of the port based vlan has link up, or atleast one port member of the policy based has an entry in the MGID or atleast one static member of the policy based vlan has link up. Otherwise, vlan is considered as DOWN. If the value is 'true' then the interface state change will not be notified to layer 3. (i.e., it always stays up). If the value is 'false' then the vlan state change will be notified to layer 3 so that IP related status reflects routable interface state.
Status: deprecated	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpConfOspfV2Table		1.3.6.1.4.1.2272.1.8.1.9
A table used to maintain OSPF information for a particular interface.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpConfOspfV2Entry

rcIpConfOspfV2Entry		1.3.6.1.4.1.2272.1.8.1.9.1
Entry containing OSPF information. An entry is automatically created in this table when routing is enabled for an interface -or- when an ip address is configured on an interface.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	RcIpConfOspfV2Entry

rcIpConfOspfV2IfIndex		1.3.6.1.4.1.2272.1.8.1.9.1.1
An unique value to identify a physical interface or a logical interface (VLAN).
Status: deprecated	Access: read-only
OBJECT-TYPE
	InterfaceIndexOrZero	0..6142

rcIpConfOspfV2IpAddr		1.3.6.1.4.1.2272.1.8.1.9.1.2
IpAddress of the IP interface.
Status: deprecated	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpConfOspfV2RtrPriority		1.3.6.1.4.1.2272.1.8.1.9.1.3
The priority of this interface. Used in multi- access networks, this field is used in the designated router election algorithm. The value 0 signifies that the router is not eligible to become the designated router on this particular network. In the event of a tie in this value, routers will use their router id as a tie breaker.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	0..FF

rcIpConfOspfV2Metric		1.3.6.1.4.1.2272.1.8.1.9.1.4
The metric for this type of service (TOS) on this interface. The default value of the TOS 0 Metric is (10^9 / ifSpeed). The value FFFF means 'no route via this TOS'. A value of 0 means the interface speed (rcIpConfOspfV2DefaultMetric) will be used as metric value, when the state of the interface is up.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	0..FFFF

rcIpConfOspfV2AuthKey		1.3.6.1.4.1.2272.1.8.1.9.1.5
The Authentication Key. If the Area's Authorization Type is simplePassword, and the key length is shorter than 8 octets, the agent will left adjust and zero fill to 8 octets. When read, ospfIfAuthKey always returns an Octet String of length zero.
Status: deprecated	Access: read-write
OBJECT-TYPE
	DisplayString	Size(8)

rcIpConfOspfV2RowStatus		1.3.6.1.4.1.2272.1.8.1.9.1.6
Row status for this entry.
Status: deprecated	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpConfOspfV2HelloInterval		1.3.6.1.4.1.2272.1.8.1.9.1.7
The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for all routers attached to a common network.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	1..FFFF

rcIpConfOspfV2RtrDeadInterval		1.3.6.1.4.1.2272.1.8.1.9.1.8
The number of seconds that a router's Hello packets have not been seen before it's neighbors declare the router down. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common network.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	1..7FFFFFFF

rcIpConfOspfV2IfAreaId		1.3.6.1.4.1.2272.1.8.1.9.1.9
A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0.0.0.0 is used for the OSPF backbone.
Status: deprecated	Access: read-write
OBJECT-TYPE
	IpAddress

rcIpConfOspfV2AuthType		1.3.6.1.4.1.2272.1.8.1.9.1.10
The authentication type specified for an interface. Additional authentication types may be assigned locally.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), simplePassword(1), md5(2)

rcIpConfOspfAreaAggregateTable		1.3.6.1.4.1.2272.1.8.1.10
A table used to maintain OSPF summary route metric parameter for a particular Area range.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpConfOspfAreaAggregateEntry

rcIpConfOspfAreaAggregateEntry		1.3.6.1.4.1.2272.1.8.1.10.1
Entry containing OSPF summary route metric parameter for a particular Area range. An entry is automatically created in this table when an area range is configured through ospfAreaAggregateTable in rfc1850rcc.mib
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpConfOspfAreaAggregateEntry

rcIpConfOspfAreaAggregateAreaID		1.3.6.1.4.1.2272.1.8.1.10.1.1
The Area the Address Aggregate is to be found within.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpConfOspfAreaAggregateLsdbType		1.3.6.1.4.1.2272.1.8.1.10.1.2
The type of the Address Aggregate. This field specifies the Lsdb type that this Address Ag- gregate applies to.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	summaryLink(3), nssaExternalLink(7)

rcIpConfOspfAreaAggregateNet		1.3.6.1.4.1.2272.1.8.1.10.1.3
The IP Address of the Net or Subnet indicated by the range.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpConfOspfAreaAggregateMask		1.3.6.1.4.1.2272.1.8.1.10.1.4
The Subnet Mask that pertains to the Net or Subnet.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpConfOspfAreaAggregateAdvertiseMetric		1.3.6.1.4.1.2272.1.8.1.10.1.5
Used to specify a metric for a Summary LSA (type 3) generated by OSPF through an area range. If this metric is set to 0, OSPF uses the cost to the farthest point in the networks being summarized as the metric.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

rcIpConfOspfAreaAggregateEffect		1.3.6.1.4.1.2272.1.8.1.10.1.6
Subnets subsumed by ranges either trigger the advertisement of the indicated aggregate (ad- vertiseMatching), or result in the subnet's not being advertised at all outside the area.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	advertiseMatching(1), doNotAdvertiseMatching(2), advertiseDoNotAggregate(3)

rcIpConfRsmltTable		1.3.6.1.4.1.2272.1.8.1.11
A table used to maintain OSPF summary route metric parameter for a particular Area range.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpConfRsmltEntry

rcIpConfRsmltEntry		1.3.6.1.4.1.2272.1.8.1.11.1
Entry containing OSPF summary route metric parameter for a particular Area range. An entry is automatically created in this table when an area range is configured through ospfAreaAggregateTable in rfc1850rcc.mib
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpConfRsmltEntry

rcIpConfRsmltIfIndex		1.3.6.1.4.1.2272.1.8.1.11.1.1
Interface Index, this is an index of the table.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcIpConfRsmltHoldDownTimer		1.3.6.1.4.1.2272.1.8.1.11.1.2
Timer value, the range of value is from 0 to 3600.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..3600

rcIpConfRsmltHoldUpTimer		1.3.6.1.4.1.2272.1.8.1.11.1.3
The range of value 0 to 3600 or 9999. 9999 means infinity.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..3600 | 9999

rcIpConfRsmltRowStatus		1.3.6.1.4.1.2272.1.8.1.11.1.4
Row Status.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpConfBfdTable		1.3.6.1.4.1.2272.1.8.1.12
BFD configuration table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpConfBfdEntry

rcIpConfBfdEntry		1.3.6.1.4.1.2272.1.8.1.12.1
Used to configure BFD on a particular interface. An entry is created automatically when the variable rcIpConfBfdEnable is set to TRUE. Once created this entry will only be deleted if the rcIpConfBfdRowStatus is set to 'destroy(6)'. In which case, the rcIpConfBfdEnable is automatically reset to the FALSE setting.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpConfBfdEntry

rcIpConfBfdIfIndex		1.3.6.1.4.1.2272.1.8.1.12.1.1
Interface number. The number can represent either a physical or logical(VLAN) interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

rcIpConfBfdMinRxInterval		1.3.6.1.4.1.2272.1.8.1.12.1.2
the min rx interval in milliseconds
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	100..65535

rcIpConfBfdTxInterval		1.3.6.1.4.1.2272.1.8.1.12.1.3
the desired tx interval in milliseconds
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	100..65535

rcIpConfBfdMultiplier		1.3.6.1.4.1.2272.1.8.1.12.1.4
the multiplier BFD wait before rx timeout
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..20

rcIpConfBfdRowStatus		1.3.6.1.4.1.2272.1.8.1.12.1.5
Used to create/delete entries
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcIpConfBfdHoldOffInterval		1.3.6.1.4.1.2272.1.8.1.12.1.6
This object specifies the hold off timer interval, in seconds. 0 means that hold off timer is disabled.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..65535

rcIpConfBfdStaticFlag		1.3.6.1.4.1.2272.1.8.1.12.1.7
This object specifies the static-flag for bfd. When disabled, the static route will go down, when bfd is disabled
Status: current	Access: read-create
OBJECT-TYPE
	EnableValue

rcIpAddrTable		1.3.6.1.4.1.2272.1.8.2
The table of addressing information relevant to this entity's IP addresses. This table is identical to the ipAddrTable in MIB2 except the columns rcIpAdEntIfIndex and rcIpAdEntAddr are reversed. Also, the table is indexed by both these variables.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpAddrEntry

rcIpAddrEntry		1.3.6.1.4.1.2272.1.8.2.1
The addressing information for one of this entity's IP addresses.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpAddrEntry

rcIpAdEntIfIndex		1.3.6.1.4.1.2272.1.8.2.1.1
The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcIpAdEntAddr		1.3.6.1.4.1.2272.1.8.2.1.2
The IP address to which this entry's addressing information pertains.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpAdEntNetMask		1.3.6.1.4.1.2272.1.8.2.1.3
The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcIpAdEntBcastAddrFormat		1.3.6.1.4.1.2272.1.8.2.1.4
The IP broadcast address format used on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	zeros(0), ones(1)

rcIpAdEntReasmMaxSize		1.3.6.1.4.1.2272.1.8.2.1.5
The size of the largest IP datagram which this entity can re-assemble from incoming IP fragmented datagrams received on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

rcIpAdEntRowStatus		1.3.6.1.4.1.2272.1.8.2.1.6
Used to create/delete entries
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpAdEntVlanId		1.3.6.1.4.1.2272.1.8.2.1.7
A value that uniquely identifies the Virtual LAN associated with this entry. This value corresponds to the lower 12 bits in the IEEE 802.1Q VLAN Tag.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..4096

rcIpAdEntBrouterPort		1.3.6.1.4.1.2272.1.8.2.1.8
Used to indicate whether this entry correponds to a brouter port (as oppose to a routable VLAN). This value cannot be changed after the row is created.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcIpAdEntMacOffset		1.3.6.1.4.1.2272.1.8.2.1.9
Used to translate the ip address into mac address. The system has 512 mac addresses of which 0-507 are reserved for Boardwalk box. 508-511 is reserved for MG. One can either mention a mac offset while configuring an ip on the vlan or it can be alloted by the system within the above range.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..511

rcIpAdEntIfType		1.3.6.1.4.1.2272.1.8.2.1.10
The address entry IfType indicates the type of the interface. In the case of circuit-less-IP there is no association with any ports. In other words, it can be thought of as a virtual interface. The value 'brouter port' indicates this interface is associated with a specific physical port. The value 'vlan' indicates a logical port that contains one or physical ports/MLT ports.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	circuitLessIP(1), brouterPort(2), vlan(3)

rcIpAdEntVrfId		1.3.6.1.4.1.2272.1.8.2.1.12
The VrfId used in this table is to associate VLANs or Brouter ports to a VRF after the creation of VLANs or Brouter ports. VRFID 0 is reserved for the Administrative VRF.
Status: current	Access: read-create
OBJECT-TYPE
	VrfIdentifier

rcIpFlowTable		1.3.6.1.4.1.2272.1.8.3
IpFlow Table. This table contain entries that correspond to RSVP records in the switching fabric Address Resolution table. A connection that has a matching entry in this table will be processed with a higher priority than connections that do not have an entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpFlowEntry

rcIpFlowEntry		1.3.6.1.4.1.2272.1.8.3.1
Proprietary flow control variables.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpFlowEntry

rcIpFlowSrcIpAddress		1.3.6.1.4.1.2272.1.8.3.1.1
The source IP address of an IP packet.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpFlowSrcIpPort		1.3.6.1.4.1.2272.1.8.3.1.2
The source port of an IP packet. A zero value in this field is used as a wildcard value.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

rcIpFlowDstIpAddress		1.3.6.1.4.1.2272.1.8.3.1.3
The destination IP address of an IP packet.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpFlowDstIpPort		1.3.6.1.4.1.2272.1.8.3.1.4
The destination port of an IP packet. A zero value in this field is used as a wildcard value.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

rcIpFlowProtocol		1.3.6.1.4.1.2272.1.8.3.1.5
The protocol type of an IP packet. A zero value in this field is used as a wildcard value.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ip(4), tcp(6), udp(17)

rcIpFlowRowStatus		1.3.6.1.4.1.2272.1.8.3.1.6
Status of entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpRouting		1.3.6.1.4.1.2272.1.8.4
OBJECT IDENTIFIER

rcIpRoutingRedistributeRipToOspf		1.3.6.1.4.1.2272.1.8.4.1
OBJECT IDENTIFIER

rcIpRoutingRedistributeRipToOspfEnable		1.3.6.1.4.1.2272.1.8.4.1.1
Used to indicate whether or not to Redistribute RIP routes to OSPF.
Status: obsolete	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpRoutingRedistributeRipToOspfExplicitMetric		1.3.6.1.4.1.2272.1.8.4.1.2
Value of metric that is used to translate the RIP route to OSPF.
Status: obsolete	Access: read-write
OBJECT-TYPE
	INTEGER	1..FFFF

rcIpRoutingRedistributeRipToOspfUseExplicitMetric		1.3.6.1.4.1.2272.1.8.4.1.3
Used to indicate whether or not to use the user specified default metric for redistributing RIP routes to OSPF.
Status: obsolete	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpRoutingRedistributeRipToOspfExternalMetricType		1.3.6.1.4.1.2272.1.8.4.1.4
Used to configure the metric type of the distributed routes to OSPF domain. type1 means the metric is comparable directly to the link state metric (cost = internal cost + external cost). type2 means the metric is considered larger than any link state metric (cost = external cost).
Status: obsolete	Access: read-write
OBJECT-TYPE
	INTEGER	type1(1), type2(2)

rcIpRoutingRedistributeOspfToRip		1.3.6.1.4.1.2272.1.8.4.2
OBJECT IDENTIFIER

rcIpRoutingRedistributeOspfToRipEnable		1.3.6.1.4.1.2272.1.8.4.2.1
Used to indicate whether or not to redistribute OSPF routes to RIP.
Status: obsolete	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpRoutingRedistributeOspfToRipExplicitMetric		1.3.6.1.4.1.2272.1.8.4.2.2
Value of metric that is used to translate the OSPF route to RIP.
Status: obsolete	Access: read-write
OBJECT-TYPE
	INTEGER	1..16

rcIpRoutingRedistributeOspfToRipUseExplicitMetric		1.3.6.1.4.1.2272.1.8.4.2.3
Used to indicate whether or not to use the user specified default metric for redistributing OSPF routes to RIP.
Status: obsolete	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpRoutingRedistributeDirectToOspf		1.3.6.1.4.1.2272.1.8.4.3
OBJECT IDENTIFIER

rcIpRoutingRedistributeDirectToOspfEnable		1.3.6.1.4.1.2272.1.8.4.3.1
Used to indicate whether directly connected networks through non-ospf interfaces are distributed to OSPF database or not. If set to true all the static routes will be added as external routes to OSPF routing domain, provided the router is configured as AS Border router. Also originates asExtern link LSA.
Status: obsolete	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpRoutingRedistributeDirectToOspfMethod		1.3.6.1.4.1.2272.1.8.4.3.2
Used to indicate whether or not to use the user specified default metric for redistributing direct routes to OSPF.
Status: obsolete	Access: read-write
OBJECT-TYPE
	INTEGER	usePortSpeed(1), useExplicitMetric(2)

rcIpRoutingRedistributeDirectToOspfExplicitMetric		1.3.6.1.4.1.2272.1.8.4.3.3
Value of metric that is used to translate the routes to directly connected networks to OSPF.
Status: obsolete	Access: read-write
OBJECT-TYPE
	INTEGER	1..FFFF

rcIpRoutingRedistributeDirectToOspfExternalMetricType		1.3.6.1.4.1.2272.1.8.4.3.4
Used to configure the metric type of the distributed routes to OSPF domain. type1 means the metric is comparable directly to the link state metric (cost = internal cost + external cost). type2 means the metric is considered larger than any link state metric (cost = external cost).
Status: obsolete	Access: read-write
OBJECT-TYPE
	INTEGER	type1(1), type2(2)

rcIpRoutingRedistributeStaticToOspf		1.3.6.1.4.1.2272.1.8.4.4
OBJECT IDENTIFIER

rcIpRoutingRedistributeStaticToOspfEnable		1.3.6.1.4.1.2272.1.8.4.4.1
Used to indicate whether static routes (that are configured locally through management protocol) are distributed to OSPF database or not. If set to true all the static routes will be added as external routes to OSPF routing domain, provided the router is configured as AS Border router. Also originates asExtern link LSA.
Status: obsolete	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpRoutingRedistributeStaticToOspfExplicitMetric		1.3.6.1.4.1.2272.1.8.4.4.2
Value of metric that is used to translate the static routes to OSPF.
Status: obsolete	Access: read-write
OBJECT-TYPE
	INTEGER	1..FFFF

rcIpRoutingRedistributeStaticToOspfUseExplicitMetric		1.3.6.1.4.1.2272.1.8.4.4.3
Used to indicate whether or not to use the user specified default metric for redistributing static routes to OSPF.
Status: obsolete	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpRoutingRedistributeStaticToOspfExternalMetricType		1.3.6.1.4.1.2272.1.8.4.4.4
Used to configure the metric type of the distributed routes to OSPF domain. type1 means the metric is comparable directly to the link state metric (cost = internal cost + external cost). type2 means the metric is considered larger than any link state metric (cost = external cost).
Status: obsolete	Access: read-write
OBJECT-TYPE
	INTEGER	type1(1), type2(2)

rcIpRoutingRedistributeStaticToOspfAdvertDefRte		1.3.6.1.4.1.2272.1.8.4.4.5
Used to indicate whether default route (that are configured locally through management protocol) should be distributed to OSPF database or not. If set to true then the default route will be added as external route to OSPF routing domain, provided the router is configured as AS Border router. Also originates asExtern link LSA.
Status: obsolete	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpRoutingRedistributeDirectToRip		1.3.6.1.4.1.2272.1.8.4.5
OBJECT IDENTIFIER

rcIpRoutingRedistributeDirectToRipEnable		1.3.6.1.4.1.2272.1.8.4.5.1
Used to indicate whether directly connected networks through non-rip interfaces are distributed to RIP or not.
Status: obsolete	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpRoutingRedistributeStaticToRip		1.3.6.1.4.1.2272.1.8.4.6
OBJECT IDENTIFIER

rcIpRoutingRedistributeStaticToRipEnable		1.3.6.1.4.1.2272.1.8.4.6.1
Used to indicate whether static routes (that are configured locally through management protocol) are distributed to RIP database or not. If set to true all the static routes will be added as external routes to RIP routing domain.
Status: obsolete	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpConfIgmpTable		1.3.6.1.4.1.2272.1.8.5
A table used to maintain IGMP information for a particular interface.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpConfIgmpEntry

rcIpConfIgmpEntry		1.3.6.1.4.1.2272.1.8.5.1
Entry containing IGMP information. An entry is automatically created in this table when routing is enabled for an interface -or- when an ip address is configured on an interface.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	RcIpConfIgmpEntry

rcIpConfIgmpIfIndex		1.3.6.1.4.1.2272.1.8.5.1.1
An unique value to identify a physical interface or a logical interface (VLAN).
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

rcIpConfIgmpQueryInterval		1.3.6.1.4.1.2272.1.8.5.1.2
The frequency at which IGMP Host-Query packets are transmitted on this interface.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

rcIpConfIgmpVersion		1.3.6.1.4.1.2272.1.8.5.1.3
The version of IGMP which is running on this interface. This object can be used to configure a router capable of running either value. For IGMP to function correctly, all routers on a LAN must be configured to run the same version of IGMP on that LAN.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	version1(1), version2(2)

rcIpConfIgmpQueryMaxResponseTime		1.3.6.1.4.1.2272.1.8.5.1.4
The maximum query response time advertised in IGMPv2 queries on this interface. Smaller values allow a router to prune groups faster.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	1..255

rcIpConfIgmpQuerierPresentTimeout		1.3.6.1.4.1.2272.1.8.5.1.5
A timeout interval. If no IGMPv2 queries are heard on this interface within this timeout interval, the local router will take over the Querier on the IP subnet to which this interface is attached.
Status: deprecated	Access: read-write
OBJECT-TYPE
	Integer32

rcIpConfIgmpLeaveEnabled		1.3.6.1.4.1.2272.1.8.5.1.6
An indication of whether the processing of IGMPv2 Leave messages is enabled on this interface.
Status: deprecated	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpConfIgmpRowStatus		1.3.6.1.4.1.2272.1.8.5.1.7
Status of entry.
Status: deprecated	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpConfIgmpRobustness		1.3.6.1.4.1.2272.1.8.5.1.8
lossiness of network.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	2..255

rcIpConfIgmpLastMemberQueryInterval		1.3.6.1.4.1.2272.1.8.5.1.9
max response in GrpSpec Query.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	1..255

rcIpConfIgmpSnoopEnable		1.3.6.1.4.1.2272.1.8.5.1.10
Enable snoop.
Status: deprecated	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpConfIgmpProxySnoopEnable		1.3.6.1.4.1.2272.1.8.5.1.11
Enable proxy snoop.
Status: deprecated	Access: read-write
OBJECT-TYPE
	TruthValue

rcIgmpGroupTable		1.3.6.1.4.1.2272.1.8.6
The (conceptual) table listing the multicast groups configured in the device.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIgmpGroupEntry

rcIgmpGroupEntry		1.3.6.1.4.1.2272.1.8.6.1
An entry (conceptual row) representing an Igmp group.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	RcIgmpGroupEntry

rcIgmpGroupIpAddress		1.3.6.1.4.1.2272.1.8.6.1.1
Multicast group Address (Class D) that others want to join. A group address can be the same for many incoming ports.
Status: deprecated	Access: read-only
OBJECT-TYPE
	IpAddress

rcIgmpGroupMembers		1.3.6.1.4.1.2272.1.8.6.1.2
IP Address of a source that has sent group report wishing to join this group.
Status: deprecated	Access: read-only
OBJECT-TYPE
	IpAddress

rcIgmpGroupInPort		1.3.6.1.4.1.2272.1.8.6.1.3
An unique value to identify a physical interface or a logical interface (VLAN), which has received Group reports from various sources.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

rcIgmpGroupExpiration		1.3.6.1.4.1.2272.1.8.6.1.4
Time left before the group report expired on this port. Only one of this variable port. This variable is updated upon receiving a group report.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Integer32

rcIgmpGroupIfIndex		1.3.6.1.4.1.2272.1.8.6.1.5
An unique value to identify a physical interface or a logical interface (VLAN), which has received Group reports from various sources.
Status: deprecated	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcIgmpGroupUserId		1.3.6.1.4.1.2272.1.8.6.1.6
User-id sending this group
Status: deprecated	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..32)

rcIgmpGroupMemberState		1.3.6.1.4.1.2272.1.8.6.1.7
Used for IGAP, to indicated member state.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	noState(1), auth(2), accStart(3), authAndAcctStart(4), authAndAcctDisabled(5)

rcIgmpGroupSessionTime		1.3.6.1.4.1.2272.1.8.6.1.8
Used for IGAP, to indicated the session time in seconds for the member. Session time is started after traffic is available to member. It can be also called AccountingTime since its values correspondes to the accounting duration of IGAP user session.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Integer32

rcIpRouteTable		1.3.6.1.4.1.2272.1.8.7
This entity's IP Routing table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpRouteEntry

rcIpRouteEntry		1.3.6.1.4.1.2272.1.8.7.1
A route to a particular destination.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpRouteEntry

rcIpRouteDest		1.3.6.1.4.1.2272.1.8.7.1.1
The destination IP address of this route. An entry with a value of 0.0.0.0 is considered a default route. Multiple routes to a single destination can appear in the table, but access to such multiple entries is dependent on the table- access mechanisms defined by the network management protocol in use.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpRouteMask		1.3.6.1.4.1.2272.1.8.7.1.2
Indicate the mask to be logical-ANDed with the destination address before being compared to the value in the rcIpRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the rcIpRouteMask by determining whether the value of the correspondent rcIpRouteDest field belong to a class-A, B, or C network, and then using one of: mask network 255.0.0.0 class-A 255.255.0.0 class-B 255.255.255.0 class-C If the value of the rcIpRouteDest is 0.0.0.0 (a default route), then the mask value is also 0.0.0.0. It should be noted that all IP routing subsystems implicitly use this mechanism.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpRouteNextHop		1.3.6.1.4.1.2272.1.8.7.1.3
The IP address of the next hop of this route. (In the case of a route bound to an interface which is realized via a broadcast media, the value of this field is the agent's IP address on that interface).
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcIpRouteMetric		1.3.6.1.4.1.2272.1.8.7.1.4
The primary routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's rcIpRouteProto value. If this metric is not used, its value should be set to -1.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcIpRouteIfIndex		1.3.6.1.4.1.2272.1.8.7.1.5
The index value which uniquely identifies the local interface through which the next hop of this route should be reached. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcIpRouteType		1.3.6.1.4.1.2272.1.8.7.1.6
The type of route.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), direct(3), indirect(4)

rcIpRouteProto		1.3.6.1.4.1.2272.1.8.7.1.7
The routing mechanism via which this route was learned. Inclusion of values for gateway routing protocols is not intended to imply that hosts should support those protocols.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), local(2), netmgmt(3), icmp(4), egp(5), ggp(6), hello(7), rip(8), is-is(9), es-is(10), ciscoIgrp(11), bbnSpfIgp(12), ospf(13), bgp(14), vOspf(15), vBgp(16), vRip(17)

rcIpRouteAge		1.3.6.1.4.1.2272.1.8.7.1.8
The number of seconds since this route was last updated or otherwise determined to be correct. Note that no semantics of `too old' can be implied except through knowledge of the routing protocol by which the route was learned.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpRouteRowStatus		1.3.6.1.4.1.2272.1.8.7.1.9
Used to create/delete entries
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpRoutePref		1.3.6.1.4.1.2272.1.8.7.1.10
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..255

rcIpRouteAltSequence		1.3.6.1.4.1.2272.1.8.7.1.11
Alternative Route Sequence. 0 denotes Best Route.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpRoutePathType		1.3.6.1.4.1.2272.1.8.7.1.12
The type of route. It is a combination of direct, indirect, best, alternative and ECMP path.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	iA(0), iAE(1), iB(2), iBE(3), dB(6), iAN(8), iAEN(9), iBN(10), iBEN(11), dBN(14), iAU(16), iAEU(17), iBU(18), iBEU(19), dBU(22), iBF(34), iBEF(35), iBV(66), iBEV(67), iBVN(74), iBEVN(75), iAS(128), iASE(129), iBS(130), iBSE(131), iBSN(138), iBSEN(139), iASV(192), iASVE(193), iBSV(194), iBSVE(195)

rcIpRouteSrcVrfId		1.3.6.1.4.1.2272.1.8.7.1.13
srcVrfId of the next-hop address
Status: current	Access: read-write
OBJECT-TYPE
	VrfIdentifier

rcIpRouteNextHopId		1.3.6.1.4.1.2272.1.8.7.1.14
Identifier of the next-hop, hostname or mac adress.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(24)

rcIpConfDhcpTable		1.3.6.1.4.1.2272.1.8.8
DHCP configuration table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpConfDhcpEntry

rcIpConfDhcpEntry		1.3.6.1.4.1.2272.1.8.8.1
Used to configure DHCP on a particular port. An entry is created automatically when the variable rcIpConfDhcpEnable is set to TRUE. Once created this entry will only be deleted if the rcIpConfDhcpRowStatus is set to 'destroy(6)'. In which case, the rcIpConfDhcpEnable is automatically reset to the FALSE setting.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpConfDhcpEntry

rcIpConfDhcpIfIndex		1.3.6.1.4.1.2272.1.8.8.1.1
Interface number. The number can represent either a physical or logical(VLAN) interface.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndexOrZero	0..6142

rcIpConfDhcpMaxHop		1.3.6.1.4.1.2272.1.8.8.1.2
Used to indicate the maximum number of hops a DHCP packet can take from the source device to the destination device (i.e., DHCP client to DHCP server).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..16

rcIpConfDhcpMinSec		1.3.6.1.4.1.2272.1.8.8.1.3
Used to indicate the minimum number of seconds to wait between receiving a DHCP packet and actually forwarding the DHCP packet to the destination device. A value of zero(0) indicates forwarding should be done immediately without any delay.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

rcIpConfDhcpMode		1.3.6.1.4.1.2272.1.8.8.1.4
Used to indicate what type of DHCP packets this interface should support. A value of none(1) will result in all incoming DHCP and BOOTP packets to be dropped.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), bootp(2), dhcp(3), both(4)

rcIpConfDhcpRowStatus		1.3.6.1.4.1.2272.1.8.8.1.5
An entry is created automatically when the variable rcIpConfDhcpEnable is set to TRUE. Once created this entry will only be deleted if the rcIpConfDhcpRowStatus is set to 'destroy(6)'. In which case, the rcIpConfDhcpEnable is automatically reset to the FALSE setting.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpConfDhcpNumRequests		1.3.6.1.4.1.2272.1.8.8.1.6
The total number of DHCP requests seen on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcIpConfDhcpNumReplies		1.3.6.1.4.1.2272.1.8.8.1.7
The total number of DHCP replies seen on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcIpConfDhcpAlwaysBroadcast		1.3.6.1.4.1.2272.1.8.8.1.8
Used to indicate if DHCP Reply packets should be broadcast to the DHCP client on this interface.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpDhcpForwardTable		1.3.6.1.4.1.2272.1.8.9
DHCP forwarding table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpDhcpForwardEntry

rcIpDhcpForwardEntry		1.3.6.1.4.1.2272.1.8.9.1
An entry used represents a DHCP forwarding directive.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpDhcpForwardEntry

rcIpDhcpForwardAgentAddr		1.3.6.1.4.1.2272.1.8.9.1.1
The IP address configured on an interface (i.e., a locally configured IP address).
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpDhcpForwardServerAddr		1.3.6.1.4.1.2272.1.8.9.1.2
The IP address of the DHCP server. If this IP address corresponds to a locally configured IP network, the DHCP packet is broadcasted out the interface the IP address is assigned to. This behavior is known as 'relay agent' mode. If this IP address is a remote address, the DHCP packet is sent via unicast to the remote device. This behavior is known as 'preferred server' mode.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpDhcpForwardEnable		1.3.6.1.4.1.2272.1.8.9.1.3
Used to indicate whether is entry should be used.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpDhcpForwardMode		1.3.6.1.4.1.2272.1.8.9.1.4
Used to indicate whether this entry pertains to BOOTP packets, DHCP packets, or both.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), bootp(2), dhcp(3), both(4)

rcIpDhcpForwardRowStatus		1.3.6.1.4.1.2272.1.8.9.1.5
Row status of this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpFilter		1.3.6.1.4.1.2272.1.8.10
OBJECT IDENTIFIER

rcIpFilterFilterTableSize		1.3.6.1.4.1.2272.1.8.10.1
Used to indicate the number of entries in the rcIpFilterTable.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpFilterGlobalListTableSize		1.3.6.1.4.1.2272.1.8.10.2
Used to indicate the number of entries in the rcIpFilterGlobalListTable.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpFilterBaseListTableSize		1.3.6.1.4.1.2272.1.8.10.3
Used to indicate the number of entries in the rcIpFilterBaseListTable.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpFilterPortTableSize		1.3.6.1.4.1.2272.1.8.10.4
Used to indicate the number of entries in the rcIpFilterPortTable.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpFilterNextAvailFilterId		1.3.6.1.4.1.2272.1.8.10.5
next available filter-id in the rcIpFilterPortTable.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpFilterTable		1.3.6.1.4.1.2272.1.8.10.20
A table containing IP filters.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpFilterEntry

rcIpFilterEntry		1.3.6.1.4.1.2272.1.8.10.20.1
IP filter attributes. The system supports a vast array of filter options. Each of these options are supported in this entry. If a particular option is not used, the column should be set to zero.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpFilterEntry

rcIpFilterType		1.3.6.1.4.1.2272.1.8.10.20.1.1
Used to indicate a particular type of filter. A 'global' filter is a filter that is applied to all packets irregardless of the packet's source or destination IP address. A 'destination' filter is used to match the destination IP address field of incoming packets. When a match is found, this filter is applied to the packet. A 'source' filter is used to match the source IP address field of incoming packets. When a match is found, this filter is applied to the packet.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	global(1), destination(2), source(3)

rcIpFilterDstAddr		1.3.6.1.4.1.2272.1.8.10.20.1.2
Destination IP address to filter on.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpFilterDstMask		1.3.6.1.4.1.2272.1.8.10.20.1.3
Destination IP subnet mask to filter on.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpFilterSrcAddr		1.3.6.1.4.1.2272.1.8.10.20.1.4
Source IP address to filter on.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpFilterSrcMask		1.3.6.1.4.1.2272.1.8.10.20.1.5
Source IP subnet mask to filter on.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpFilterId		1.3.6.1.4.1.2272.1.8.10.20.1.6
This filter's unique identifier(id). This id is automatically generated by the system when a filter is created. This id is used in the 'rcIpFilterGlobalListTable' and 'rcIpFilterBaseListTable' when grouping one or more filters into a filter list.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4096

rcIpFilterName		1.3.6.1.4.1.2272.1.8.10.20.1.7
This filter's name.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..15)

rcIpFilterProtocolType		1.3.6.1.4.1.2272.1.8.10.20.1.8
Type of protocol to filter on.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ignore(0), icmp(1), tcp(6), udp(17), ipsecesp(50), ipsecah(51), ospf(89), vrrp(112), usrDefined(256)

rcIpFilterSrcPort		1.3.6.1.4.1.2272.1.8.10.20.1.9
TCP/UDP source port to filter on.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

rcIpFilterSrcOption		1.3.6.1.4.1.2272.1.8.10.20.1.10
Type of matching to perform on the field 'rcIpFilterSrcPort'. For 'source' and 'destination' filters, this value can only be 'equal(1)'.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	equal(0), notEqual(1), greater(2), less(3), ignore(4)

rcIpFilterDstPort		1.3.6.1.4.1.2272.1.8.10.20.1.11
TCP/UDP destination port to filter on.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

rcIpFilterDstOption		1.3.6.1.4.1.2272.1.8.10.20.1.12
Type of matching to perform on the field 'rcIpFilterDstPort'. For 'source' and 'destination' filters, this value can only be 'equal(1)'.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	equal(0), notEqual(1), greater(2), less(3), ignore(4)

rcIpFilterCopyToCpu		1.3.6.1.4.1.2272.1.8.10.20.1.13
Used to specify whether a packet matching this filter should be copied to the CPU.
Status: deprecated	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpFilterMirror		1.3.6.1.4.1.2272.1.8.10.20.1.14
Used to specify whether a packet matching this filter should be mirrored to the port specified by 'rcMirrorByPortMirrorPort'.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpFilterHighPriority		1.3.6.1.4.1.2272.1.8.10.20.1.15
Used to specify whether a packet matching this filter should be forwarded with high priority.
Status: deprecated	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpFilterTcpConnect		1.3.6.1.4.1.2272.1.8.10.20.1.16
Used to specify whether a TCP packet matching this filter should be accepted. Pass only those matching TCP packets with either the ACK bit or RST bit set. Apply only if the IP Protocol is set to TCP.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpFilterIeeeVlanPriority		1.3.6.1.4.1.2272.1.8.10.20.1.17
Used to specify the priority bits for explicit IEEE VLAN tag for a packet matching this filter. If this priority bit field is greater than the priority field currently in the IEEE tag in the Packet Header, this priority field will be loaded into the Packet Header.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..7

rcIpFilterUsePktLimit		1.3.6.1.4.1.2272.1.8.10.20.1.18
Used to specify whether the 'rcIpFilterPktLimit' field in this entry should be used when applying this filter.
Status: deprecated	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpFilterPktLimit		1.3.6.1.4.1.2272.1.8.10.20.1.19
The maximum packet size limit to filter against.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

rcIpFilterRowStatus		1.3.6.1.4.1.2272.1.8.10.20.1.20
Row status of this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpFilterMode		1.3.6.1.4.1.2272.1.8.10.20.1.21
Used to specify the operation mode for this entry. 'useDefaultAction' means use the setting specified in the 'rcIpFilterPortDefaultAction' variable. 'forward' means forward the packet if the packet satisfies this policy. 'drop' means drop the packet if the packet satisfies this policy. 'forwardToNextHop' means forward the packet to the next hop if the packet satisfies this policy. This variable setting has higher precedence than the setting in 'rcIpFilterPortDefaultAction'.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	useDefaultAction(1), forward(2), drop(3), forwardToNextHop(4)

rcIpFilterIpTosRule		1.3.6.1.4.1.2272.1.8.10.20.1.22
Used to specify the operation mode for this entry. 'none' means do not manupulate the Ip ToS byte. 'ipTosRule1' means manipulate the Ip ToS byte according to Quid/Gid Rule 1 which is defined in rcIpTosRuleOrRule1. 'ipTosRule2' means manipulate the Ip ToS byte according to Quid/Gid Rule 2 which is defined in rcIpTosRuleOrRule2. 'ipTosRule3' means manipulate the Ip ToS byte according to Quid/Gid Rule 3 which is defined in rcIpTosRuleOrRule3.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), ipTosRule1(1), ipTosRule2(2), ipTosRule3(3)

rcIpFilterStopOnMatch		1.3.6.1.4.1.2272.1.8.10.20.1.23
Used to stop further filtering if this filter is applied.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpFilterDiffServMatchIeee8021PEnable		1.3.6.1.4.1.2272.1.8.10.20.1.24
Used to specify whether the value stored in the variable 'rcIpFilterDiffServMatchIeee8021P' should be used in this filter.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpFilterDiffServMatchIeee8021P		1.3.6.1.4.1.2272.1.8.10.20.1.25
Used to specify the match value for the 802.1P field. If the 802.1P field in the incoming packet matches this value, then this filter will be applied to the packet.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..7

rcIpFilterDiffServMatchDscpEnable		1.3.6.1.4.1.2272.1.8.10.20.1.26
Used to specify whether the values stored in the variable 'rcIpFilterDiffServMatchDscp' and 'rcIpFilterDiffServMatchDscpReserved' should be used in this filter.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpFilterDiffServMatchDscp		1.3.6.1.4.1.2272.1.8.10.20.1.27
Used to specify the match value for the DSCP. If the DSCP in the incoming packet matches this value, then this filter will be applied to the packet. The DSCP represents the high-order 6 bits of the TOS byte (in network order).
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(6)

rcIpFilterDiffServMatchDscpReserved		1.3.6.1.4.1.2272.1.8.10.20.1.28
Used to specify the match value of the low-order 2 bits of the TOS byte (in network order).
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(2)

rcIpFilterDiffServModifyIeee8021PEnable		1.3.6.1.4.1.2272.1.8.10.20.1.29
Used to specify whether the value stored in the variable 'rcIpFilterDiffServModifyIeee8021P' should be used in this filter.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpFilterDiffServModifyIeee8021P		1.3.6.1.4.1.2272.1.8.10.20.1.30
Used to specify the value the 802.1P field should be modified to if this filter is applied. The modification is applied at the egress point.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..7

rcIpFilterDiffServModifyDscpEnable		1.3.6.1.4.1.2272.1.8.10.20.1.31
Used to specify whether the value stored in the variable 'rcIpFilterDiffServModifyDscp' should be used in this filter.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpFilterDiffServModifyDscp		1.3.6.1.4.1.2272.1.8.10.20.1.32
Used to specify what the value of the DSCP should be modified to if this filter is applied. The modification is applied at the egress point. The DSCP represents the high-order 6 bits of the TOS byte (in network order).
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(6)

rcIpFilterDiffServModifyDscpReserved		1.3.6.1.4.1.2272.1.8.10.20.1.33
Used to specify the modify value of the low-order 2 bits of the TOS byte (in network order).
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(2)

rcIpFilterDiffServTrafficProfileId		1.3.6.1.4.1.2272.1.8.10.20.1.34
Used to specify which traffic profile should be applied to packets matching this filter. Traffic profiles are specified in the 'rc2kQosTrafficProfileTable' table. A '0' value means do not apply any traffic profile.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..64

rcIpFilterMatchIcmpRequest		1.3.6.1.4.1.2272.1.8.10.20.1.35
Used to specify whether matching on ICMP Request packets should be performed.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpFilterMatchIpFragment		1.3.6.1.4.1.2272.1.8.10.20.1.36
Used to specify whether matching on fragmented IP packets should be performed.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpFilterStatisticEnable		1.3.6.1.4.1.2272.1.8.10.20.1.37
Used to turn on/off Counters for this filter.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpFilterInOctets		1.3.6.1.4.1.2272.1.8.10.20.1.38
The number of In-Octets for this filter.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter64

rcIpFilterInPackets		1.3.6.1.4.1.2272.1.8.10.20.1.39
The number of In-Packets for this filter.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter64

rcIpFilterRateLimitDiscardPackets		1.3.6.1.4.1.2272.1.8.10.20.1.40
The number of packets discarded due to rate limiting.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter64

rcIpFilterNextHopForwardIpAddr		1.3.6.1.4.1.2272.1.8.10.20.1.41
Next hop forward Ip address.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcIpFilterNextHopUnreachableDropEnable		1.3.6.1.4.1.2272.1.8.10.20.1.42
If next hop is unreachalbe, enable/disable to drop the packet.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpFilterProtocolTypeUsrDefined		1.3.6.1.4.1.2272.1.8.10.20.1.43
When rcIpFilterProtocolType is set to usrDefined(256) in an IP Filter, this field represents the 8-bit user defined protocol identifier.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

rcIpFilterIngressOctets		1.3.6.1.4.1.2272.1.8.10.20.1.44
The number of In-Octets for this filter.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcIpFilterIngressPkts		1.3.6.1.4.1.2272.1.8.10.20.1.45
The number of In-Packets for this filter.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcIpFilterRateLimitDiscardPkts		1.3.6.1.4.1.2272.1.8.10.20.1.46
The number of packets discarded due to rate limiting.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcIpFilterGlobalListTable		1.3.6.1.4.1.2272.1.8.10.21
A table used to store global filter list information. Each row in the table contains a set of individual filters that make up a particular filter list.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpFilterGlobalListEntry

rcIpFilterGlobalListEntry		1.3.6.1.4.1.2272.1.8.10.21.1
Global filter list attributes.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpFilterGlobalListEntry

rcIpFilterGlobalListId		1.3.6.1.4.1.2272.1.8.10.21.1.1
An unique value to identify a particular global filter list.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..100

rcIpFilterGlobalListName		1.3.6.1.4.1.2272.1.8.10.21.1.2
Name of this filter list.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..15)

rcIpFilterGlobalListFilterIdListSize		1.3.6.1.4.1.2272.1.8.10.21.1.3
Used to indicate the number of filters are associated with this filter list.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..8

rcIpFilterGlobalListFilterIdList		1.3.6.1.4.1.2272.1.8.10.21.1.4
Used to indicate zero or more filters that are associated with this filter list. Each filter identifier is stored as two bytes in this array starting from offset zero. Any unused bytes should be set to zero.
Status: current	Access: read-write
OBJECT-TYPE
	IdList	Size(16)

rcIpFilterGlobalListRowStatus		1.3.6.1.4.1.2272.1.8.10.21.1.5
Row status of this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpFilterGlobalListMemberPorts		1.3.6.1.4.1.2272.1.8.10.21.1.6
Ports filter is used on.
Status: current	Access: read-only
OBJECT-TYPE
	PortSet

rcIpFilterBaseListTable		1.3.6.1.4.1.2272.1.8.10.22
A table used to store base filter list information. Each row in the table contains a set of individual filters that make up a particular filter list.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpFilterBaseListEntry

rcIpFilterBaseListEntry		1.3.6.1.4.1.2272.1.8.10.22.1
Base filter list attributes.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpFilterBaseListEntry

rcIpFilterBaseListId		1.3.6.1.4.1.2272.1.8.10.22.1.1
An unique value to identify a particular base filter list.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	300..1000

rcIpFilterBaseListName		1.3.6.1.4.1.2272.1.8.10.22.1.2
Name of this filter list.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..15)

rcIpFilterBaseListFilterIdListSize		1.3.6.1.4.1.2272.1.8.10.22.1.3
Used to indicate the number of filters are associated with this filter list.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..128

rcIpFilterBaseListFilterIdList		1.3.6.1.4.1.2272.1.8.10.22.1.4
Used to indicate zero or more filters that are associated with this filter list. Each filter identifier is stored as two bytes in this array starting from offset zero. Any unused bytes should be set to zero.
Status: current	Access: read-write
OBJECT-TYPE
	IdList	Size(256)

rcIpFilterBaseListRowStatus		1.3.6.1.4.1.2272.1.8.10.22.1.5
Row status of this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpFilterBaseListMemberPorts		1.3.6.1.4.1.2272.1.8.10.22.1.6
Ports filter is used on.
Status: current	Access: read-only
OBJECT-TYPE
	PortSet

rcIpFilterPortTable		1.3.6.1.4.1.2272.1.8.10.23
A table used to store port filtering information.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpFilterPortEntry

rcIpFilterPortEntry		1.3.6.1.4.1.2272.1.8.10.23.1
Port entry attributes.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpFilterPortEntry

rcIpFilterPortIfIndex		1.3.6.1.4.1.2272.1.8.10.23.1.1
IfIndex value of a port where filtering is applied.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcIpFilterPortFilterListSize		1.3.6.1.4.1.2272.1.8.10.23.1.2
Used to indicate the number of filter list(s) that are assigned to this port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..128

rcIpFilterPortFilterList		1.3.6.1.4.1.2272.1.8.10.23.1.3
Used to indicate zero or more filter lists that are associated with this port. Each filter list identifier is stored as two bytes in this array starting from offset zero. Any unused bytes should be set to zero.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(256)

rcIpFilterPortMode		1.3.6.1.4.1.2272.1.8.10.23.1.4
Used to indicate when filters applied to this port should be treated as 'permit' or 'deny' filters. When filters are not enabled on the port the mode is set to none. The port does not block any packet. Mode None cannot be used when PortEnable is true. On a port configured as 'permit', any packet that satisfies a filter is allowed to be forwarded. On a port configured as 'deny', any packet that satisfies a filter is dropped.
Status: obsolete	Access: read-write
OBJECT-TYPE
	INTEGER	permit(1), deny(2), none(3)

rcIpFilterPortEnable		1.3.6.1.4.1.2272.1.8.10.23.1.5
Used to indicate whether filtering is configured on this port.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpFilterPortRowStatus		1.3.6.1.4.1.2272.1.8.10.23.1.6
Row status of this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpFilterPortDefaultAction		1.3.6.1.4.1.2272.1.8.10.23.1.7
Used to indicate the default action that should be performed when an IP filter applies to a particular port. When filters are not enabled on the port the action is set to 'none' which means the port does not block any packet. 'none' cannot be used when PortEnable is true. On a port configured as 'forward', any packet that satisfies a filter is allowed to be forwarded. On a port configured as 'drop', any packet that satisfies a filter is dropped.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	forward(1), drop(2), none(3)

rcIpFilterPortNumGlobalFilters		1.3.6.1.4.1.2272.1.8.10.23.1.8
# of global filters
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpFilterPortNumBaseFilters		1.3.6.1.4.1.2272.1.8.10.23.1.9
# of base filters
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpFilterMediaDevTableSize		1.3.6.1.4.1.2272.1.8.10.24
Used to indicate the number of entries in the rcIpFilterMediaDevTable.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpFilterMediaDevTable		1.3.6.1.4.1.2272.1.8.10.25
A table used to store media filter list information. Each row in the table contains a set of individual filters that make up a particular filter list for a particular platform/device combination.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpFilterMediaDevEntry

rcIpFilterMediaDevEntry		1.3.6.1.4.1.2272.1.8.10.25.1
Device attributes and the filters' attributes.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpFilterMediaDevEntry

rcIpFilterMediaDevId		1.3.6.1.4.1.2272.1.8.10.25.1.1
Media Id in the rcIpFilterMediaDevTable.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	3000..3127

rcIpFilterMediaDevName		1.3.6.1.4.1.2272.1.8.10.25.1.2
Media Device Name. This includes the platform and the physical/soft device.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..63)

rcIpFilterMediaDevPlatformType		1.3.6.1.4.1.2272.1.8.10.25.1.3
Platform identifier or type. These are the currently supported platforms.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), cse1k(1), cse2k(2), cse3k(3), bcm(4), meridianLineCard(5), meridianTrunkCard(6), msl100IP(7), vcon(8), minerva(9), useDefined(10)

rcIpFilterMediaDevDeviceType		1.3.6.1.4.1.2272.1.8.10.25.1.4
Device identifier or type. There are the currently supported device types.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), i2002(1), i2004(2), i2050(3), tps(4), gateway(5), useDefined(6)

rcIpFilterMediaDevIpAddress		1.3.6.1.4.1.2272.1.8.10.25.1.5
Media Device IP Address.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcIpFilterMediaDevStreamsIds		1.3.6.1.4.1.2272.1.8.10.25.1.6
An array used to identify which streams are assigned to MediaDevEntry. Each stream ID is stored as a two octet value. The first octet in the pair holds bits 15-8 of the stream ID, while the second octet holds bits 7-0 of the stream ID.
Status: current	Access: read-only
OBJECT-TYPE
	IdList	Size(16)

rcIpFilterMediaDevMemberPorts		1.3.6.1.4.1.2272.1.8.10.25.1.7
Media Device port port members. These are the system physical ports.
Status: current	Access: read-only
OBJECT-TYPE
	PortSet

rcIpFilterMediaDevStatisticEnable		1.3.6.1.4.1.2272.1.8.10.25.1.8
Used to turn on/off statistics' counters for all the filters for the device.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpFilterMediaDevRowStatus		1.3.6.1.4.1.2272.1.8.10.25.1.9
Row Status.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpFilterMediaStreamTableSize		1.3.6.1.4.1.2272.1.8.10.26
Used to indicate the number of entries in the rcIpFilterMediaStreamTable.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpFilterMediaStreamTable		1.3.6.1.4.1.2272.1.8.10.27
A table used to store tcp/udp port information for a set of filters that make up a particular filter list for a particular platform/device combination.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpFilterMediaStreamEntry

rcIpFilterMediaStreamEntry		1.3.6.1.4.1.2272.1.8.10.27.1
Layer 4 Port attributes and the filters' attributes.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpFilterMediaStreamEntry

rcIpFilterMediaStreamMediaId		1.3.6.1.4.1.2272.1.8.10.27.1.1
Media Id in the rcIpFilterMediaDevTable.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	3000..3127

rcIpFilterMediaStreamStreamId		1.3.6.1.4.1.2272.1.8.10.27.1.2
Port range Id in the rcIpFilterMediaStreamTable.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4

rcIpFilterMediaStreamName		1.3.6.1.4.1.2272.1.8.10.27.1.3
Media Stream Name.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..31)

rcIpFilterMediaStreamProtocol		1.3.6.1.4.1.2272.1.8.10.27.1.4
Type of transport protocol to filter on. Multimedia applications often use UDP and some use TCP. Any Layer 4 protocol number supported by IP can be added here in future.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	tcp(6), udp(17)

rcIpFilterMediaStreamPortMin		1.3.6.1.4.1.2272.1.8.10.27.1.5
TCP/UDP source or destination port to filter on.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

rcIpFilterMediaStreamPortMax		1.3.6.1.4.1.2272.1.8.10.27.1.6
TCP/UDP source or destination port to filter on.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

rcIpFilterMediaStreamPortOption		1.3.6.1.4.1.2272.1.8.10.27.1.7
Src port or destination port of both.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	src(1), dest(2), srcDest(3)

rcIpFilterMediaStreamType		1.3.6.1.4.1.2272.1.8.10.27.1.8
Type of stream to filter on.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	signal(1), media(2)

rcIpFilterMediaStreamRemarkDscp		1.3.6.1.4.1.2272.1.8.10.27.1.9
Used to specify what the value of the DSCP should be modified to if this stream is identified. The modification is applied at the egress point. The DSCP represents the high-order 6 bits of the TOS byte (in network order).
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(6)

rcIpFilterMediaStreamMatchDscp		1.3.6.1.4.1.2272.1.8.10.27.1.10
Used to specify what the value of the DSCP should be match with in the stream identification. DSCP represents the high-order 6 bit of the TOS byte (in network order).
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(6)

rcIpFilterMediaStreamRowStatus		1.3.6.1.4.1.2272.1.8.10.27.1.11
Row Status.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpPolicy		1.3.6.1.4.1.2272.1.8.11
OBJECT IDENTIFIER

rcIpPolicyAddrTableSize		1.3.6.1.4.1.2272.1.8.11.1
Used to indicate the number of entries in the rcIpPolicyAddrTable.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Integer32

rcIpPolicyAddrTable		1.3.6.1.4.1.2272.1.8.11.2
A table used to store different types list entries. Each row in the table contains a list entry that is used by a set of announce policies.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpPolicyAddrEntry

rcIpPolicyAddrEntry		1.3.6.1.4.1.2272.1.8.11.2.1
Route entry attributes.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	RcIpPolicyAddrEntry

rcIpPolicyAddrIpAddr		1.3.6.1.4.1.2272.1.8.11.2.1.1
The network address for this type of list entry. This value is required for all types of lists.
Status: deprecated	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpPolicyAddrId		1.3.6.1.4.1.2272.1.8.11.2.1.2
Identifier of this entry. Used internally to identify this entry.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Integer32

rcIpPolicyAddrAddrListIdListSize		1.3.6.1.4.1.2272.1.8.11.2.1.3
Used to indicate the number of id(s) in the rcIpPolicyAddrListIdList variable.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	0..128

rcIpPolicyAddrAddrListIdList		1.3.6.1.4.1.2272.1.8.11.2.1.4
Used to indicate zero or more rcIpPolicyAddrListEntry(s) that are referring to this entry. Each list-id identifier is stored as two bytes in this array starting from offset zero. Any unused bytes should be set to zero.
Status: deprecated	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(256)

rcIpPolicyAddrRowStatus		1.3.6.1.4.1.2272.1.8.11.2.1.5
Row status of this entry.
Status: deprecated	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpPolicyNetTableSize		1.3.6.1.4.1.2272.1.8.11.3
Used to indicate the number of entries in the rcIpPolicyNetTable.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Integer32

rcIpPolicyNetTable		1.3.6.1.4.1.2272.1.8.11.4
A table used to store different types list entries. Each row in the table contains a list entry that is used by a set of announce policies.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpPolicyNetEntry

rcIpPolicyNetEntry		1.3.6.1.4.1.2272.1.8.11.4.1
Route entry attributes.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	RcIpPolicyNetEntry

rcIpPolicyNetAddr		1.3.6.1.4.1.2272.1.8.11.4.1.1
The network address for this type of list entry. This value is required for all types of lists.
Status: deprecated	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpPolicyNetMask		1.3.6.1.4.1.2272.1.8.11.4.1.2
The route mask for this type of list entry. This value is meaningful only if rcIpPolicyNetEntry is equal to exactNet(1), rangeNet(2), advertiseNet(3). For other types it should have the value 0.0.0.0.
Status: deprecated	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpPolicyNetId		1.3.6.1.4.1.2272.1.8.11.4.1.3
Used internally to recognize this entry.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Integer32

rcIpPolicyNetNetListIdListSize		1.3.6.1.4.1.2272.1.8.11.4.1.4
Used to indicate the number of id(s) in the rcIpPolicyNetListIdList variable.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	0..128

rcIpPolicyNetNetListIdList		1.3.6.1.4.1.2272.1.8.11.4.1.5
Used to indicate zero or more rcIpPolicyNetListEntry(s) that are referring to this entry. Each list-id identifier is stored as two bytes in this array starting from offset zero. Any unused bytes should be set to zero.
Status: deprecated	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(256)

rcIpPolicyNetRowStatus		1.3.6.1.4.1.2272.1.8.11.4.1.6
Row status of this entry.
Status: deprecated	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpPolicyAddrListTableSize		1.3.6.1.4.1.2272.1.8.11.5
Used to indicate the number of entries in the rcIpPolicyAddrListTable.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Integer32

rcIpPolicyAddrListTable		1.3.6.1.4.1.2272.1.8.11.6
A table used to group rcIpPolicyAddrEntry(s) into a list.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpPolicyAddrListEntry

rcIpPolicyAddrListEntry		1.3.6.1.4.1.2272.1.8.11.6.1
Route entry attributes.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	RcIpPolicyAddrListEntry

rcIpPolicyAddrListId		1.3.6.1.4.1.2272.1.8.11.6.1.1
A value that uniquely identifies this list of rcIpPolicyAddrListEntry.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	1..1000

rcIpPolicyAddrListName		1.3.6.1.4.1.2272.1.8.11.6.1.3
An administratively-assigned name for this list.
Status: deprecated	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..15)

rcIpPolicyAddrListIdListSize		1.3.6.1.4.1.2272.1.8.11.6.1.4
Used to indicate the number of rcIpPolicyAddrNetEntry id(s) in the rcIpPolicyAddrListIdList variable.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	0..128

rcIpPolicyAddrListIdList		1.3.6.1.4.1.2272.1.8.11.6.1.5
Used to indicate zero or more AddrListId that are associated to this list. Each AddrList identifier is stored as two bytes in this array starting from offset zero. Any unused bytes should be set to zero.
Status: deprecated	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(256)

rcIpPolicyAddrListPolicyIdListSize		1.3.6.1.4.1.2272.1.8.11.6.1.6
Used to indicate the number of policy id(s) in the Policy Id list. That are referring to this list.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	0..128

rcIpPolicyAddrListPolicyIdList		1.3.6.1.4.1.2272.1.8.11.6.1.7
Used to indicate zero or more policies that are referring to this entry. Each policy identifier is stored as two bytes in this array starting from offset zero. Any unused bytes should be set to zero.
Status: deprecated	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(256)

rcIpPolicyAddrListRowStatus		1.3.6.1.4.1.2272.1.8.11.6.1.8
Row status of this entry.
Status: deprecated	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpPolicyRipAnnounceTableSize		1.3.6.1.4.1.2272.1.8.11.7
Used to indicate the number of entries in the rcIpPolicyRipAnnounceTable.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Integer32

rcIpPolicyRipAnnounceTable		1.3.6.1.4.1.2272.1.8.11.8
A table used to store set of announce policies configured for RIP routing protocol. The Number of entries is given by rcIpPolicyNumRipPolicies.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpPolicyRipAnnounceEntry

rcIpPolicyRipAnnounceEntry		1.3.6.1.4.1.2272.1.8.11.8.1
Entry containing configuration information for a particular announce policy.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	RcIpPolicyRipAnnounceEntry

rcIpPolicyRipAnnounceId		1.3.6.1.4.1.2272.1.8.11.8.1.1
A value that uniquely identifies the policy associated with this entry.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	1..1000

rcIpPolicyRipAnnounceName		1.3.6.1.4.1.2272.1.8.11.8.1.2
An administratively-assigned name for this policy.
Status: deprecated	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..15)

rcIpPolicyRipAnnounceEnable		1.3.6.1.4.1.2272.1.8.11.8.1.3
It indicates whether this policy is enabled or not. The policy should be applied only if it is set to 'true'.
Status: deprecated	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpPolicyRipAnnounceExactNetListId		1.3.6.1.4.1.2272.1.8.11.8.1.4
Used to indicate the number of 'exact' type entries that are configured for this policy. An entry with type 'exactNet' or 'rangeNet' represents the network list. This indicates which networks will match a particular announce policy. An entry with a 'exact' type means to only match the specific network advertisement (netaddr & mask). An 'exact' entry with addr=0.0.0.0 and mask=0.0.0.0 means 'match the default route'. If set to '0', this policy applies to all the routes.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	0..1000

rcIpPolicyRipAnnounceRangeNetListId		1.3.6.1.4.1.2272.1.8.11.8.1.5
Used to indicate zero or more 'range' network entries that are associated with this policy. An entry with a 'range' type means to match any network number that falls in the range indicated by the addr & mask. A 'range' entry with addr=0.0.0.0 and mask=0.0.0.0 means 'match any route'. If set to '0', this policy applies to all the routes.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	0..1000

rcIpPolicyRipAnnounceRipGatewayListId		1.3.6.1.4.1.2272.1.8.11.8.1.6
Used to identify the RIP-gatewayList in the list that are associated with this policy. This field has meaning only for RIP sourced routes and if RIP is included as a RouteSource. The list contains one or more rip-routers (other side of the interface) addresses that could send RIP updates to this router. If a router address is included in this list, this policy applies to RIP advertisements from that router. If set to '0', this policy applies to RIP updates received from any rip routers/interfaces.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	0..1000

rcIpPolicyRipAnnounceRipInterfaceListId		1.3.6.1.4.1.2272.1.8.11.8.1.7
Used to indicate the number of entries in the ripInterfaceIdList that are configured for this policy. This field has meaning only for RIP sourced routes and if RIP is included as a RouteSource. The list contains one or more rip-interface addresses on this router. If an interface address is incuded in this list, this policy applies to RIP advertisements received on that interface. A value of '0' indicates thtat this policy applies to RIP updates received on any rip-interface.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	0..1000

rcIpPolicyRipAnnounceOspfRouterListId		1.3.6.1.4.1.2272.1.8.11.8.1.8
Used to indicate the number of entries in the OspfRouteIds that are configured for this policy. This field has meaning only for OSPF sourced routes and if OSPF is included as a RouteSource. The list contains one or more router IDs of OSPF routers. If a routerId is included in this list, this policy applies to OSPF advertisements received from that router. A value of '0' indicates that this policy applies to any OPSF routes received from any router.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	0..1000

rcIpPolicyRipAnnounceAnnounceInterfaceListId		1.3.6.1.4.1.2272.1.8.11.8.1.9
Used to indicate the number of entries in the AnnounceInterfaceids that are configured for this policy. The list contains one or more outbound interface addresses. If the outbound interface address in this list, the policy applies to RIP updates/advertisements sent through this interface. A value of '0' indicates that this policy applies to any outbound RIP interface on this router.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	0..1000

rcIpPolicyRipAnnouncePrecedence		1.3.6.1.4.1.2272.1.8.11.8.1.10
Is used while comparing this policy rule with other policy that a given route may match. A rule with a higher precedence value will be chosen over one with a smaller value. In the case of a tie, the PolicyId is used (larger wins).
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

rcIpPolicyRipAnnounceRouteSource		1.3.6.1.4.1.2272.1.8.11.8.1.11
Is represented as bitset to indicate route sources. It can contain one or more route sources. If the route source is in this bit map, then a route from that source that meets the other criteria of this policy will match the policy.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	direct(1), static(2), rip(4), ospf(8), any(15)

rcIpPolicyRipAnnounceAdvertiseNetListId		1.3.6.1.4.1.2272.1.8.11.8.1.12
Used to indicate the number of entries in the AdvertiseNetList that are configured for this policy. This has meaning only if the Action is set to 'announce'. It is useful to send or advertise networks that differ from actual network in the routing table. Also allows advertisement of an aggregate or default along with the actual network. Aggregation is useful if a number of routes in the table falls in a certain range. Can save space by sending aggregate route instead of the individual routes. Actual network/route is included in the update only if there is a match or there there is an entry (address & mask pair) 255.255.255.255/255.255.255.255 in the list.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	0..1000

rcIpPolicyRipAnnounceAction		1.3.6.1.4.1.2272.1.8.11.8.1.13
It indicates whether the route should be announced or not.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	announce(1), ignore(2)

rcIpPolicyRipAnnounceOspfRouteType		1.3.6.1.4.1.2272.1.8.11.8.1.14
Ospf Route type. It applies to OSPF sourced routes only. 'type1' means to apply this policy to only type1 OSPF external routes. 'type2' means to apply this policy to only type2 OSPF external routes. 'internal' means 'match ospf specfic routes'. 'any' means apply this policy to all OSPF external routes.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	type1(1), type2(2), external(3), internal(4), any(5)

rcIpPolicyRipAnnounceRipMetric		1.3.6.1.4.1.2272.1.8.11.8.1.15
RIP metric. The value is meaningful only if the action is set to 'announce'. This is optional export metric to use when advertising a route that matches this policy. If set to zero, the routing table metric calculated for RIP is is used.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	0..15

rcIpPolicyRipAnnounceRowStatus		1.3.6.1.4.1.2272.1.8.11.8.1.16
Row status of this entry.
Status: deprecated	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpPolicyOspfAnnounceTableSize		1.3.6.1.4.1.2272.1.8.11.9
Used to indicate the number of entries in the rcIpPolicyOspfAnnounceTable.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Integer32

rcIpPolicyOspfAnnounceTable		1.3.6.1.4.1.2272.1.8.11.10
A table used to store set of announce policies configured for OSPF routing protocol. The Number of entries is given by rcIpPolicyNumOspfPolicies.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpPolicyOspfAnnounceEntry

rcIpPolicyOspfAnnounceEntry		1.3.6.1.4.1.2272.1.8.11.10.1
Entry containing configuration information for a particular announce policy.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	RcIpPolicyOspfAnnounceEntry

rcIpPolicyOspfAnnounceId		1.3.6.1.4.1.2272.1.8.11.10.1.1
A value that uniquely identifies the policy associated with this entry.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	2001..3000

rcIpPolicyOspfAnnounceName		1.3.6.1.4.1.2272.1.8.11.10.1.2
An administratively-assigned name for this policy.
Status: deprecated	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..15)

rcIpPolicyOspfAnnounceEnable		1.3.6.1.4.1.2272.1.8.11.10.1.3
It indicates whether this policy is enabled or not. The policy should be applied only if it is set to 'true'.
Status: deprecated	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpPolicyOspfAnnounceExactNetListId		1.3.6.1.4.1.2272.1.8.11.10.1.4
Used to indicate the number of 'exact' type entries that are configured for this policy. An entry with type 'exactNet' or 'rangeNet' represents the network list. This indicates which networks will match a particular announce policy. An entry with a 'exact' type means to only match the specific network advertisement (netaddr & mask). An 'exact' entry with addr=0.0.0.0 and mask=0.0.0.0 means 'match the default route'. If set to '0', this policy applies to all the routes.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	0..1000

rcIpPolicyOspfAnnounceRangeNetListId		1.3.6.1.4.1.2272.1.8.11.10.1.5
Used to indicate zero or more 'range' network entries that are associated with this policy. An entry with a 'range' type means to match any network number that falls in the range indicated by the addr & mask. A 'range' entry with addr=0.0.0.0 and mask=0.0.0.0 means 'match any route'. If set to '0', this policy applies to all the routes.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	0..1000

rcIpPolicyOspfAnnounceRipGatewayListId		1.3.6.1.4.1.2272.1.8.11.10.1.6
Used to identify the RIP-gatewayList in the list that are associated with this policy. This field has meaning only for RIP sourced routes and if RIP is included as a RouteSource. The list contains one or more rip-routers (other side of the interface) addresses that could send RIP updates to this router. If a router address is included in this list, this policy applies to RIP advertisements from that router. If set to '0', this policy applies to RIP updates received from any rip routers/interfaces.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	0..1000

rcIpPolicyOspfAnnounceRipInterfaceListId		1.3.6.1.4.1.2272.1.8.11.10.1.7
Used to indicate the number of entries in the ripInterfaceIdList that are configured for this policy. This field has meaning only for RIP sourced routes and if RIP is included as a RouteSource. The list contains one or more rip-interface addresses on this router. If an interface address is incuded in this list, this policy applies to RIP advertisements received on that interface. A value of '0' indicates thtat this policy applies to RIP updates received on any rip-interface.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	0..1000

rcIpPolicyOspfAnnouncePrecedence		1.3.6.1.4.1.2272.1.8.11.10.1.8
Is used while comparing this policy rule with other policy that a given route may match. A rule with a higher precedence value will be chosen over one with a smaller value. In the case of a tie, the PolicyId is used (larger wins).
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

rcIpPolicyOspfAnnounceRouteSource		1.3.6.1.4.1.2272.1.8.11.10.1.9
Is represented as bit map to indicate route sources. It can contain one or more route sources. If the route source is in this bit map, then a route from that source that meets the other criteria of this policy will match the policy.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	direct(1), static(2), rip(4), any(7)

rcIpPolicyOspfAnnounceAdvertiseNetListId		1.3.6.1.4.1.2272.1.8.11.10.1.10
Used to indicate the number of entries in the AdvertiseNetList that are configured for this policy. This has meaning only if the Action is set to 'announce'. It is useful to send or advertise networks that differ from actual network in the routing table. Also allows advertisement of an aggregate or default along with the actual network. Aggregation is useful if a number of routes in the table falls in a certain range. Can save space by sending aggregate route instead of the individual routes. Actual network/route is included in the update only if there is a match or there there is an entry (address & mask pair) 255.255.255.255/255.255.255.255 in the list.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	0..1000

rcIpPolicyOspfAnnounceAction		1.3.6.1.4.1.2272.1.8.11.10.1.11
It indicates whether the route should be announced or not.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	announce(1), ignore(2)

rcIpPolicyOspfAnnounceExtMetricType		1.3.6.1.4.1.2272.1.8.11.10.1.12
Ospf External metric type. It is used to indicate what type of the external metric it is. 'type1' means to the cost is 'internal ospf cost + ExtMetric'. 'type2' means the ospf-metric is equal to 'type2'.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	type1(1), type2(2)

rcIpPolicyOspfAnnounceExtMetric		1.3.6.1.4.1.2272.1.8.11.10.1.13
OSPF External metric. The value is meaningful only if the action is set to 'announce'. This is optional export metric to use when advertising a route that matches this policy. Value '0' is used to indicate that route's actual cost is used to announce.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

rcIpPolicyOspfAnnounceRowStatus		1.3.6.1.4.1.2272.1.8.11.10.1.14
Row status of this entry.
Status: deprecated	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpPolicyRipAcceptTableSize		1.3.6.1.4.1.2272.1.8.11.11
Used to indicate the number of entries in the rcIpPolicyRipAcceptTable.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Integer32

rcIpPolicyRipAcceptTable		1.3.6.1.4.1.2272.1.8.11.12
A table used to store set of accept policies configured for RIP routing protocol. The Number of entries is given by rcIpPolicyNumRipPolicies.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpPolicyRipAcceptEntry

rcIpPolicyRipAcceptEntry		1.3.6.1.4.1.2272.1.8.11.12.1
Entry containing configuration information for a particular accept policy.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	RcIpPolicyRipAcceptEntry

rcIpPolicyRipAcceptId		1.3.6.1.4.1.2272.1.8.11.12.1.1
A value that uniquely identifies the policy associated with this entry.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	4001..5000

rcIpPolicyRipAcceptName		1.3.6.1.4.1.2272.1.8.11.12.1.2
An administratively-assigned name for this policy.
Status: deprecated	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..15)

rcIpPolicyRipAcceptEnable		1.3.6.1.4.1.2272.1.8.11.12.1.3
It indicates whether this policy is enabled or not. The policy should be applied only if it is set to 'true'.
Status: deprecated	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpPolicyRipAcceptExactNetListId		1.3.6.1.4.1.2272.1.8.11.12.1.4
Used to indicate the number of 'exact' type entries that are configured for this policy. An entry with type 'exactNet' or 'rangeNet' represents the network list. This indicates which networks will match a particular accept policy. An entry with a 'exact' type means to only match the specific network advertisement (netaddr & mask). An 'exact' entry with addr=0.0.0.0 and mask=0.0.0.0 means 'match the default route'.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	0..1000

rcIpPolicyRipAcceptRangeNetListId		1.3.6.1.4.1.2272.1.8.11.12.1.5
Used to indicate zero or more 'range' network entries that are associated with this policy. An entry with a 'range' type means to match any network number that falls in the range indicated by the addr & mask. A 'range' entry with addr=0.0.0.0 and mask=0.0.0.0 means 'match any route'. A null list means 'match any route'.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	0..1000

rcIpPolicyRipAcceptRipGatewayListId		1.3.6.1.4.1.2272.1.8.11.12.1.6
Used to identify the RIP-gatewayList in the PolicyListTable that iares associated with this policy. The list contains the addresses of one or more routers that could send RIP updates to this router. If a router address is included in this list, this policy applies to RIP advertisements from that router. If set to '0', this policy applies to RIP updates from any router.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	0..1000

rcIpPolicyRipAcceptRipInterfaceListId		1.3.6.1.4.1.2272.1.8.11.12.1.7
Used to indicate ListId defined for RipInterfaceList in the rcIpPolicyListTable that is assiciated with this policy. The list contains the addresses of one or more interfaces on this router. If an interface address is included in the list, this policy applies to RIP advertisements received on that interface. If set to '0', this policy applies to RIP updates received on any interface.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	0..1000

rcIpPolicyRipAcceptPrecedence		1.3.6.1.4.1.2272.1.8.11.12.1.8
Is used while comparing this policy rule with other policy that a given route may match. A rule with a higher precedence value will be chosen over one with a smaller value. In the case of a tie, the PolicyId is used (larger wins).
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

rcIpPolicyRipAcceptAction		1.3.6.1.4.1.2272.1.8.11.12.1.9
It indicates whether the route should be acceptd or not.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	accept(1), ignore(2)

rcIpPolicyRipAcceptInjectNetListId		1.3.6.1.4.1.2272.1.8.11.12.1.10
Used to indicate the ListId of the InjectNetList in the rcIpPolicyListTable entry that is assiciated with for this policy. If teh action is 'accept' and if it is desired to insert networks into the routing table that differ from the actual advertised network. For instance, if a number of networks in a certain range are learned and an aggregate advertisement could be inserted instead of the individual networks. Upon receiving a route that matches this policy, all networks in this list will be considered for inclusion in the routing table. If the list is empty or if the value of the ListId is '0' then the actual received network is considered. An encoding of 255.255.255.255/255.255.255.255 means 'match the actual received network.'. This allows insertion of an aggregate or default along with the actual netowrk.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	0..1000

rcIpPolicyRipAcceptApplyMask		1.3.6.1.4.1.2272.1.8.11.12.1.11
If the 'action' is set to 'accept' and the actual received network will be considered, this is an optional IP address mask that will be applied to the network number from the RIP update. This is used to override the interface's subnet mask in the presence of networks with variable length subnet masks.
Status: deprecated	Access: read-write
OBJECT-TYPE
	IpAddress

rcIpPolicyRipAcceptRowStatus		1.3.6.1.4.1.2272.1.8.11.12.1.12
Row status of this entry.
Status: deprecated	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpPolicyOspfAcceptTableSize		1.3.6.1.4.1.2272.1.8.11.13
Used to indicate the number of entries in the rcIpPolicyOspfAcceptTable.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Integer32

rcIpPolicyOspfAcceptTable		1.3.6.1.4.1.2272.1.8.11.14
A table used to store set of accept policies configured for RIP routing protocol. The Number of entries is given by rcIpPolicyNumRipPolicies.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpPolicyOspfAcceptEntry

rcIpPolicyOspfAcceptEntry		1.3.6.1.4.1.2272.1.8.11.14.1
Entry containing configuration information for a particular accept policy.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	RcIpPolicyOspfAcceptEntry

rcIpPolicyOspfAcceptId		1.3.6.1.4.1.2272.1.8.11.14.1.1
A value that uniquely identifies the policy associated with this entry.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	6001..7000

rcIpPolicyOspfAcceptName		1.3.6.1.4.1.2272.1.8.11.14.1.2
An administratively-assigned name for this policy.
Status: deprecated	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..15)

rcIpPolicyOspfAcceptEnable		1.3.6.1.4.1.2272.1.8.11.14.1.3
It indicates whether this policy is enabled or not. The policy should be applied only if it is set to 'true'.
Status: deprecated	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpPolicyOspfAcceptExactNetListId		1.3.6.1.4.1.2272.1.8.11.14.1.4
Used to indicate the number of 'exact' type entries that are configured for this policy. An entry with type 'exactNet' or 'rangeNet' represents the network list. This indicates which networks will match a particular accept policy. An entry with a 'exact' type means to only match the specific network advertisement (netaddr & mask). An 'exact' entry with addr=0.0.0.0 and mask=0.0.0.0 means 'match the default route'.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	0..1000

rcIpPolicyOspfAcceptRangeNetListId		1.3.6.1.4.1.2272.1.8.11.14.1.5
Used to indicate zero or more 'range' network entries that are associated with this policy. An entry with a 'range' type means to match any network number that falls in the range indicated by the addr & mask. A 'range' entry with addr=0.0.0.0 and mask=0.0.0.0 means 'match any route'. A null list means 'match any route'.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	0..1000

rcIpPolicyOspfAcceptPrecedence		1.3.6.1.4.1.2272.1.8.11.14.1.6
Is used while comparing this policy rule with other policy that a given route may match. A rule with a higher precedence value will be chosen over one with a smaller value. In the case of a tie, the PolicyId is used (larger wins).
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

rcIpPolicyOspfAcceptAction		1.3.6.1.4.1.2272.1.8.11.14.1.7
It indicates whether the route should be acceptd or not.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	accept(1), ignore(2)

rcIpPolicyOspfAcceptInjectNetListId		1.3.6.1.4.1.2272.1.8.11.14.1.8
Used to indicate the ListId of the InjectNetList in the rcIpPolicyListTable entry that is assiciated with for this policy. If teh action is 'accept' and if it is desired to insert networks into the routing table that differ from the actual advertised network. For instance, if a number of networks in a certain range are learned and an aggregate advertisement could be inserted instead of the individual networks. Upon receiving a route that matches this policy, all networks in this list will be considered for inclusion in the routing table. If the list is empty or if the value of the ListId is '0' then the actual received network is considered. An encoding of 255.255.255.255/255.255.255.255 means 'match the actual received network.'. This allows insertion of an aggregate or default along with the actual netowrk.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	0..1000

rcIpPolicyOspfAcceptExtType		1.3.6.1.4.1.2272.1.8.11.14.1.9
Used to indicate the ospf external type. This parameter describes which types of OSPF ASE routes match this policy. 'any' means 'match either ASE type 1 or 2'. 'type1' means 'match any external type 1'. 'type2' means 'match any external type 2
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	type1(1), type2(2), any(3)

rcIpPolicyOspfAcceptRowStatus		1.3.6.1.4.1.2272.1.8.11.14.1.10
Row status of this entry.
Status: deprecated	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpPolicyNetListTableSize		1.3.6.1.4.1.2272.1.8.11.15
Used to indicate the number of entries in the rcIpPolicyNetListTable.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Integer32

rcIpPolicyNetListTable		1.3.6.1.4.1.2272.1.8.11.16
A table used to group rcIpPolicyAddrEntry(s) into a list.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpPolicyNetListEntry

rcIpPolicyNetListEntry		1.3.6.1.4.1.2272.1.8.11.16.1
Route entry attributes.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	RcIpPolicyNetListEntry

rcIpPolicyNetListId		1.3.6.1.4.1.2272.1.8.11.16.1.1
A value that uniquely identifies this list of rcIpPolicyNetListEntry.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	1..1000

rcIpPolicyNetListName		1.3.6.1.4.1.2272.1.8.11.16.1.3
An administratively-assigned name for this list.
Status: deprecated	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..15)

rcIpPolicyNetListIdListSize		1.3.6.1.4.1.2272.1.8.11.16.1.4
Used to indicate the number of rcIpPolicyNetEntry id(s) in the rcIpPolicyNetListIdList variable.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	0..128

rcIpPolicyNetListIdList		1.3.6.1.4.1.2272.1.8.11.16.1.5
Used to indicate zero or more NetListId that are associated to this list. Each NetList identifier is stored as two bytes in this array starting from offset zero. Any unused bytes should be set to zero.
Status: deprecated	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(256)

rcIpPolicyNetListPolicyIdListSize		1.3.6.1.4.1.2272.1.8.11.16.1.6
Used to indicate the number of policy id(s) in the Policy Id list. That are referring to this list.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	0..128

rcIpPolicyNetListPolicyIdList		1.3.6.1.4.1.2272.1.8.11.16.1.7
Used to indicate zero or more policies that are referring to this entry. Each policy identifier is stored as two bytes in this array starting from offset zero. Any unused bytes should be set to zero.
Status: deprecated	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(256)

rcIpPolicyNetListRowStatus		1.3.6.1.4.1.2272.1.8.11.16.1.8
Row status of this entry.
Status: deprecated	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpDvmrp		1.3.6.1.4.1.2272.1.8.12
OBJECT IDENTIFIER

rcIpDvmrpGlobal		1.3.6.1.4.1.2272.1.8.12.1
OBJECT IDENTIFIER

rcIpDvmrpGlobalEnable		1.3.6.1.4.1.2272.1.8.12.1.1
The enabled status of IP Multicast Dvmrp routing on this router.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpDvmrpGlobalUpdateInterval		1.3.6.1.4.1.2272.1.8.12.1.2
Route upd interval
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	10..2000

rcIpDvmrpGlobalTriggeredUpdateInterval		1.3.6.1.4.1.2272.1.8.12.1.3
Trigger upd interval
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	5..1000

rcIpDvmrpGlobalLeafTimeOut		1.3.6.1.4.1.2272.1.8.12.1.4
Hold down timer for leaf
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	25..4000

rcIpDvmrpGlobalNbrTimeOut		1.3.6.1.4.1.2272.1.8.12.1.5
Time to age out nbr
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	35..8000

rcIpDvmrpGlobalNbrProbeInterval		1.3.6.1.4.1.2272.1.8.12.1.6
How often to send probe
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	5..30

rcIpDvmrpGlobalRouteExpireTimeOut		1.3.6.1.4.1.2272.1.8.12.1.7
This parameter defines the route expiration timeout in seconds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	20..4000

rcIpDvmrpGlobalFwdCacheTimeOut		1.3.6.1.4.1.2272.1.8.12.1.8
This is the Forward Cache Value in second. This value is going to be used in aging prune entries in seconds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	10..86400

rcIpDvmrpGlobalRouteDiscardTimeOut		1.3.6.1.4.1.2272.1.8.12.1.9
This parameter defines time to garbage collect route in seconds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	25..8000

rcIpDvmrpGlobalRouteSwitchTimeOut		1.3.6.1.4.1.2272.1.8.12.1.10
This parameter defines the route discard timeout in seconds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	20..2000

rcIpDvmrpGlobalGenerateTrap		1.3.6.1.4.1.2272.1.8.12.1.12
Enabling the dvmrp to generate trap.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpDvmrpGlobalGenerateLog		1.3.6.1.4.1.2272.1.8.12.1.13
Enabling the dvmrp to generate log.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpDvmrpTable		1.3.6.1.4.1.2272.1.8.12.2
Dvmrp Interface extension table. This table augments the standard dvmrpInterfaceTable defined in .
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpDvmrpTableEntry

rcIpDvmrpTableEntry		1.3.6.1.4.1.2272.1.8.12.2.1
Entry containing Proprietary DVMRP interface information. An entry is automatically created in this table when an ip address is configured on an interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpDvmrpTableEntry

rcIpDvmrpTableIfIndex		1.3.6.1.4.1.2272.1.8.12.2.1.1
The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcIpDvmrpTableEnable		1.3.6.1.4.1.2272.1.8.12.2.1.2
The administrative status of DVMRP in the router. The value 'enabled' denotes that the DVMRP is enableed on the interface; 'disabled' disables it on the interface.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpDvmrpTableMetric		1.3.6.1.4.1.2272.1.8.12.2.1.3
Dvmrp cost on this interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..31

rcIpDvmrpTableAdvSelf		1.3.6.1.4.1.2272.1.8.12.2.1.4
Used to indicate whether the switch can advertise this local network
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpDvmrpTableLocalAddr		1.3.6.1.4.1.2272.1.8.12.2.1.5
The IP address of this interface.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpDvmrpTableInPolicyName		1.3.6.1.4.1.2272.1.8.12.2.1.6
Dvmrp Accept Policy name that is configured on this interface.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rcIpDvmrpTableOutPolicyName		1.3.6.1.4.1.2272.1.8.12.2.1.7
Dvmrp Announce Policy name that is configured on this interface.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rcIpDvmrpTableDefRtLis		1.3.6.1.4.1.2272.1.8.12.2.1.8
Used to indicate whether the switch can learn DVMRP default route over this interface
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpDvmrpTableDefRtSup		1.3.6.1.4.1.2272.1.8.12.2.1.9
Used to indicate whether the switch should supply DVMRP default route over this interface
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpDvmrpTableDefRtMet		1.3.6.1.4.1.2272.1.8.12.2.1.10
Used to specify the cost of the DVMRP default route that this interface generates and supplies when it is configured to supply default route
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcIpDvmrpTableInterfaceType		1.3.6.1.4.1.2272.1.8.12.2.1.11
Dvmrp Interface type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	active(1), passive(2)

rcIpUdp		1.3.6.1.4.1.2272.1.8.13
OBJECT IDENTIFIER

rcIpUdpProtocolTableSize		1.3.6.1.4.1.2272.1.8.13.1
Used to indicate the number of entries in the rcIpUdpProtocolTable.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpUdpProtocolTable		1.3.6.1.4.1.2272.1.8.13.2
list of UDP protocols. Used to determine whether to forward the UDP broadcast packet or not.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpUdpProtocolEntry

rcIpUdpProtocolEntry		1.3.6.1.4.1.2272.1.8.13.2.1
Used to include a particular UDP port in the table. An entry in this table indicates that the box might do forwarding of UDP broadcast packets if there is a matching entry for this packet in the rcIpUdpPortFwdTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpUdpProtocolEntry

rcIpUdpProtocolPortNumber		1.3.6.1.4.1.2272.1.8.13.2.1.1
well-known UDP Port number. Pre-assigned port number for this protocol. Port used by the server process as its contact port. It cannot be BOOTP/DHCP port#s 67, 68.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

rcIpUdpProtocolName		1.3.6.1.4.1.2272.1.8.13.2.1.2
Used to indicate the name of the protocol that is running on top of UDP protocol. cannot change the name once created. This should be set while creating the entry.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(1..15)

rcIpUdpProtocolRowStatus		1.3.6.1.4.1.2272.1.8.13.2.1.3
Rowstatus of this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpUdpPortFwdTableSize		1.3.6.1.4.1.2272.1.8.13.3
Used to indicate the number of entries in the rcIpUdpPortFwdTable.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpUdpPortFwdTable		1.3.6.1.4.1.2272.1.8.13.4
Udp forward entry table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpUdpPortFwdEntry

rcIpUdpPortFwdEntry		1.3.6.1.4.1.2272.1.8.13.4.1
An entry is configured to specify forwarding policy parameters.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpUdpPortFwdEntry

rcIpUdpPortFwdDestPort		1.3.6.1.4.1.2272.1.8.13.4.1.1
The well-known port number defined for UDP/TCP depending on the value of IpProtoType field in this entry. This port number has to be defined in the rcIpUdpProtoTable. In order to select this policy the destination port number has to match the DestPort value.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

rcIpUdpPortFwdDestAddr		1.3.6.1.4.1.2272.1.8.13.4.1.2
Destination IP address. The IP addres to which the UDP/TCP broadcast should be forwarded. This IP address can be any IP server address or subnet broadcast address. If the IP address is one of the routable interface's address on the router, the frame will be rebroadcast out as a limited broadcast. If the Ip address is that of a server then the received broadcast packet will be sent as a unicast packet to this address.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpUdpPortFwdId		1.3.6.1.4.1.2272.1.8.13.4.1.3
Identifier of this entry. Used internally to identify this entry.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpUdpPortFwdFwdListIdListSize		1.3.6.1.4.1.2272.1.8.13.4.1.4
Used to indicate the number of id(s) in the rcIpUdpPortFwdListId variable.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..128

rcIpUdpPortFwdFwdListIdList		1.3.6.1.4.1.2272.1.8.13.4.1.5
Used to indicate zero or more rcIpUdpPortFwdListEntry(s) that are referring to this entry. Each list-id identifier is stored as two bytes in this array starting from offset zero. Any unused bytes should be set to zero.
Status: current	Access: read-only
OBJECT-TYPE
	IdList	Size(64)

rcIpUdpPortFwdNumFwdPackets		1.3.6.1.4.1.2272.1.8.13.4.1.6
The total number of UDP/TCP broadcast packets forwarded using this policy.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcIpUdpPortFwdNumDropPacketsTtlExpired		1.3.6.1.4.1.2272.1.8.13.4.1.7
The total number of UDP/TCP broadcast packets dropped because the TTL has expired.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcIpUdpPortFwdNumDropPacketsDestUnreach		1.3.6.1.4.1.2272.1.8.13.4.1.8
The total number of UDP/TCP broadcast packets dropped because the rcIpUdpPortFwdDestAddr specified in this policy was unreachable.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcIpUdpPortFwdRowStatus		1.3.6.1.4.1.2272.1.8.13.4.1.9
Row status of this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpUdpPortFwdListTableSize		1.3.6.1.4.1.2272.1.8.13.5
Used to indicate the number of entries in the rcIpUdpPortFwdListTable.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpUdpPortFwdListTable		1.3.6.1.4.1.2272.1.8.13.6
A table used to group rcIpUdpPortFwdEntry(s) into a list.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpUdpPortFwdListEntry

rcIpUdpPortFwdListEntry		1.3.6.1.4.1.2272.1.8.13.6.1
Route entry attributes.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpUdpPortFwdListEntry

rcIpUdpPortFwdListId		1.3.6.1.4.1.2272.1.8.13.6.1.1
A value that uniquely identifies this list of rcIpUdpPortFwdListEntry.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1000

rcIpUdpPortFwdListName		1.3.6.1.4.1.2272.1.8.13.6.1.3
An administratively-assigned name for this list.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..15)

rcIpUdpPortFwdListFwdIdListSize		1.3.6.1.4.1.2272.1.8.13.6.1.4
Used to indicate the number of rcIpUdpPortFwdNetEntry id(s) in the rcIpUdpPortFwdListIdList variable.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..64

rcIpUdpPortFwdListFwdIdList		1.3.6.1.4.1.2272.1.8.13.6.1.5
Used to indicate zero or more UdpPortFwd entries that are associated to this list. Each entry identifier is stored as two bytes in this array starting from offset zero. Any unused bytes should be set to zero.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(128)

rcIpUdpPortFwdListRowStatus		1.3.6.1.4.1.2272.1.8.13.6.1.6
Row status of this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpUdpConfBroadcastIntfTableSize		1.3.6.1.4.1.2272.1.8.13.7
Used to indicate the number of entries in the rcIpUdpBroadcastIntfTable.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpUdpConfBroadcastIntfTable		1.3.6.1.4.1.2272.1.8.13.8
IP broadcast forward configuration table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpUdpConfBroadcastIntfEntry

rcIpUdpConfBroadcastIntfEntry		1.3.6.1.4.1.2272.1.8.13.8.1
Used to configure UDP broadcast forward on a particular interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpUdpConfBroadcastIntfEntry

rcIpUdpConfBroadcastIntfLocalIfAddr		1.3.6.1.4.1.2272.1.8.13.8.1.1
The ip address of the local interface that is partipating in the forwarding UDP broadcast packets.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpUdpConfBroadcastIntfUdpPortFwdListId		1.3.6.1.4.1.2272.1.8.13.8.1.2
Used to indicate the number UDP ports that this interface is configured to forward. A value of '0' indicates that this interface will not forward any UDP broadcast packets. This is a required field to create an entry.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..1000

rcIpUdpConfBroadcastIntfMaxTtl		1.3.6.1.4.1.2272.1.8.13.8.1.3
Used to indicate the maximum number of hops an IP broadcast packet can take from the source device to the destination device.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..16

rcIpUdpConfBroadcastIntfNumRxPkts		1.3.6.1.4.1.2272.1.8.13.8.1.4
The total number of UDP/TCP broadcast packets received by this local interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcIpUdpConfBroadcastIntfNumFwdPkts		1.3.6.1.4.1.2272.1.8.13.8.1.5
The total number of UDP/TCP broadcast packets forwarded.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcIpUdpConfBroadcastIntfNumDropPktsMaxTtlExpired		1.3.6.1.4.1.2272.1.8.13.8.1.6
The total number of UDP/TCP broadcast packets dropped because the TTL has expired.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcIpUdpConfBroadcastIntfNumDropPktsDestUnreach		1.3.6.1.4.1.2272.1.8.13.8.1.7
The total number of UDP broadcast packets dropped because the destination was unreachable.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcIpUdpConfBroadcastIntfNumDropPktsUnknownPort		1.3.6.1.4.1.2272.1.8.13.8.1.8
The total number of UDP/TCP broadcast packets dropped because the destination port/protocol specified has no matching forwarding policy.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcIpUdpConfBroadcastIntfRowStatus		1.3.6.1.4.1.2272.1.8.13.8.1.9
Entry row status.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpUdpConfBroadcastIntfBroadCastMask		1.3.6.1.4.1.2272.1.8.13.8.1.10
The subnet mask of the local interface that is used for broadcasting the UDP broadcast packets.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcIpTosRule		1.3.6.1.4.1.2272.1.8.14
OBJECT IDENTIFIER

rcIpTosRuleAndMask		1.3.6.1.4.1.2272.1.8.14.1
And Mask. The Ip ToS byte in the Ip header is logically ANDed with this value, and then logically ORed with the one of the OrRules below.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

rcIpTosRuleOrRule1		1.3.6.1.4.1.2272.1.8.14.2
Quid/Gid Or rule #1. The Ip ToS byte in the Ip header is logically ORed with this value.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

rcIpTosRuleOrRule2		1.3.6.1.4.1.2272.1.8.14.3
Quid/Gid Or rule #2. The Ip ToS byte in the Ip header is logically ORed with this value.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

rcIpTosRuleOrRule3		1.3.6.1.4.1.2272.1.8.14.4
Quid/Gid Or rule #3. The Ip ToS byte in the Ip header is logically ORed with this value.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

rcIpTosRuleTosPriorityEnable		1.3.6.1.4.1.2272.1.8.14.5
Enable Tos priority.
Status: deprecated	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpTosRuleTosThreshold		1.3.6.1.4.1.2272.1.8.14.6
tos threshold
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	level0(0), level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7)

rcIpStaticRoute		1.3.6.1.4.1.2272.1.8.15
OBJECT IDENTIFIER

rcIpStaticRouteTableSize		1.3.6.1.4.1.2272.1.8.15.1
size of Ip Static Route Table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpStaticRouteTable		1.3.6.1.4.1.2272.1.8.15.2
This table is used to add static IP routes to the device. Routes added into this table will automatically show-up in the 'rcIpRouteTable' when the device is actively using the route to forward IP traffic.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpStaticRouteEntry

rcIpStaticRouteEntry		1.3.6.1.4.1.2272.1.8.15.2.1
A static route to a particular destination.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpStaticRouteEntry

rcIpStaticRouteDest		1.3.6.1.4.1.2272.1.8.15.2.1.1
The destination IP address of this route. An entry with a value of 0.0.0.0 is considered a default route. Multiple routes to a single destination can appear in the table, but access to such multiple entries is dependent on the table- access mechanisms defined by the network management protocol in use.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpStaticRouteMask		1.3.6.1.4.1.2272.1.8.15.2.1.2
Indicate the mask to be logical-ANDed with the destination address before being compared to the value in the rcIpRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the rcIpRouteMask by determining whether the value of the correspondent rcIpRouteDest field belong to a class-A, B, or C network, and then using one of: mask network 255.0.0.0 class-A 255.255.0.0 class-B 255.255.255.0 class-C If the value of the rcIpRouteDest is 0.0.0.0 (a default route), then the mask value is also 0.0.0.0. It should be noted that all IP routing subsystems implicitly use this mechanism.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpStaticRouteNextHop		1.3.6.1.4.1.2272.1.8.15.2.1.3
The IP address of the next hop of this route. (In the case of a route bound to an interface which is realized via a broadcast media, the value of this field is the agent's IP address on that interface).
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpStaticRouteMetric		1.3.6.1.4.1.2272.1.8.15.2.1.4
The primary routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's rcIpRouteProto value. If this metric is not used, its value should be set to -1.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..FFFF

rcIpStaticRouteIfIndex		1.3.6.1.4.1.2272.1.8.15.2.1.5
The index value which uniquely identifies the local interface through which the next hop of this route should be reached. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex	0..65535

rcIpStaticRoutePreference		1.3.6.1.4.1.2272.1.8.15.2.1.6
Used to indicate the route preference of this entry. If there are more than one route that can be used to forward IP traffic, the route that has a highest preference will be used instead of a lower preference one. The higher the number, the higher the preference.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..255

rcIpStaticRouteEnable		1.3.6.1.4.1.2272.1.8.15.2.1.7
Used to enable/disable this entry.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpStaticRouteStatus		1.3.6.1.4.1.2272.1.8.15.2.1.8
Used to indicate the current status of this entry.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	inactive(0), active(1)

rcIpStaticRouteRowStatus		1.3.6.1.4.1.2272.1.8.15.2.1.9
Used to create/delete entries
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpStaticRouteLocalNextHop		1.3.6.1.4.1.2272.1.8.15.2.1.10
Used to enable/disable this entry. True indicate that the static route becomes active only if switch has a local route to the network. False indicates that the static route becomes active if switch has a local route or dynamic route.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpStaticRouteBfdTableSize		1.3.6.1.4.1.2272.1.8.15.3
size of IP static route BFD table.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..256

rcIpStaticRouteBfdTable		1.3.6.1.4.1.2272.1.8.15.4
This table is used to hold next hop addresses on which BFD is enabled.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpStaticRouteBfdEntry

rcIpStaticRouteBfdEntry		1.3.6.1.4.1.2272.1.8.15.4.1
An IP address of the next hop of the BFD session.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpStaticRouteBfdEntry

rcIpStaticRouteBfdNextHop		1.3.6.1.4.1.2272.1.8.15.4.1.1
The IP address of the next hop of the BFD session.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpStaticRouteBfdRowStatus		1.3.6.1.4.1.2272.1.8.15.4.1.2
Used to create/delete entries
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcIpPim		1.3.6.1.4.1.2272.1.8.16
OBJECT IDENTIFIER

rcIpPimGlobal		1.3.6.1.4.1.2272.1.8.16.1
OBJECT IDENTIFIER

rcIpPimGlobalEnable		1.3.6.1.4.1.2272.1.8.16.1.1
enable feature
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpPimGlobalMode		1.3.6.1.4.1.2272.1.8.16.1.2
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	dm(1), sm(2), smdm(3), ssm(4)

rcIpPimGlobalMbr		1.3.6.1.4.1.2272.1.8.16.1.3
enable/disable pim multicast border router feature
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpPimGlobalRegisterSuppTimer		1.3.6.1.4.1.2272.1.8.16.1.4
Each source's DR maintains, per (S,G), a Register- Suppression-timer in seconds. The Register- Suppression-timer is started by the Register-Stop message; upon expiration, the source's DR resumes sending data packets to the RP, encapsulated in the Register message.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	6..65535

rcIpPimGlobalInterfaceTableSize		1.3.6.1.4.1.2272.1.8.16.1.5
table size
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpPimGlobalUniRouteChgTimeOut		1.3.6.1.4.1.2272.1.8.16.1.6
This timer allows a better tuning on how fast the routing information is going to get updated from RTM (the frequency at which the RTM is polled for routing information updates).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	2..65535

rcIpPimGlobalDiscardDataTimeOut		1.3.6.1.4.1.2272.1.8.16.1.7
This timer is used to discard data until the Join is received from the RP. A ipmc discard record is created and deleted once the timer expires and/or when a Join is received.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	5..65535

rcIpPimGlobalCRPADVTimeOut		1.3.6.1.4.1.2272.1.8.16.1.8
Routers configured as candidate RPs use this timer to periodically send C-RP-Adv messages. Upon expiry, a C-RP-Adv message is sent to the elected BSR.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	5..26214

rcIpPimGlobalBootStrapPeriod		1.3.6.1.4.1.2272.1.8.16.1.9
At the elected BSR, this is the interval between originating Bootstrap messages.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	5..32757

rcIpPimGlobalStaticRP		1.3.6.1.4.1.2272.1.8.16.1.10
Enable/Disable Static RP feature.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpPimGlobalActivityChkInterval		1.3.6.1.4.1.2272.1.8.16.1.11
Activity check interval for polling PIM SG traffic activity information.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	intv15(15), intv30(30), intv210(210)

rcIpPimGlobalFwdCacheTimeOut		1.3.6.1.4.1.2272.1.8.16.1.12
PIM forward cache expiry value in seconds.This value is going to be used in aging PIM mroutes in seconds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	10..86400

rcIpPimGlobalFastJoinPrune		1.3.6.1.4.1.2272.1.8.16.1.13
Pim Fast Join Prune.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpPimGlobalStaticRPSpecificRt		1.3.6.1.4.1.2272.1.8.16.1.14
Enable/Disable Static RP specific route feature.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpPimTable		1.3.6.1.4.1.2272.1.8.16.2
IP Pim table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpPimEntry

rcIpPimEntry		1.3.6.1.4.1.2272.1.8.16.2.1
An entry of Ip Pim Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpPimEntry

rcIpPimIfIndex		1.3.6.1.4.1.2272.1.8.16.2.1.1
port
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcIpPimEnable		1.3.6.1.4.1.2272.1.8.16.2.1.2
enable interface
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpPimMode		1.3.6.1.4.1.2272.1.8.16.2.1.3
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	dense(1), sparse(2), sparseDense(3), ssm(4)

rcIpPimHelloInterval		1.3.6.1.4.1.2272.1.8.16.2.1.4
frq. at which hello sent.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..18724

rcIpPimJoinPruneInterval		1.3.6.1.4.1.2272.1.8.16.2.1.5
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..18724

rcIpPimCBSRPreference		1.3.6.1.4.1.2272.1.8.16.2.1.6
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	-1..255

rcIpPimIntfType		1.3.6.1.4.1.2272.1.8.16.2.1.7
Pim interface type.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	active(1), passive(2)

rcIpPimInterfaceTable		1.3.6.1.4.1.2272.1.8.16.3
IP Pim table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpPimInterfaceEntry

rcIpPimInterfaceEntry		1.3.6.1.4.1.2272.1.8.16.3.1
An entry of Ip Pim Interface Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpPimInterfaceEntry

rcIpPimInterfaceIfIndex		1.3.6.1.4.1.2272.1.8.16.3.1.1
port
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcIpPimInterfaceOperState		1.3.6.1.4.1.2272.1.8.16.3.1.2
The current operational state of this PIM interface. This object is deprecated in favor of ifOperStatus.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2)

rcIpPimInterfaceType		1.3.6.1.4.1.2272.1.8.16.3.1.3
Pim interface type.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	active(1), passive(2)

rcIpPimInterfaceCBSREnable		1.3.6.1.4.1.2272.1.8.16.3.1.4
Enable/disable Candidate BSR on pim local interface.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpPimStaticRPTable		1.3.6.1.4.1.2272.1.8.16.4
The table lists all the RPs configured statically for various IP multicast groups.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpPimStaticRPEntry

rcIpPimStaticRPEntry		1.3.6.1.4.1.2272.1.8.16.4.1
An entry (conceptual row) in the rcIpPimStaticRPTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpPimStaticRPEntry

rcIpPimStaticRPGroupAddress		1.3.6.1.4.1.2272.1.8.16.4.1.1
The IP multicast group address which, when combined with rcIpPimStaticRPGroupMask, identifies a group prefix for which rcIpPimStaticRPAddress is a static-RP.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpPimStaticRPGroupMask		1.3.6.1.4.1.2272.1.8.16.4.1.2
The multicast group address mask which, when combined with rcIpPimStaticRPGroupAddress, identifies a group prefix for which rcIpPimStaticRPAddress is a static-RP.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpPimStaticRPAddress		1.3.6.1.4.1.2272.1.8.16.4.1.3
The (unicast) address of the static-RP.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpPimStaticRPRowStatus		1.3.6.1.4.1.2272.1.8.16.4.1.4
The status of this row, by which new entries may be created, or old entries deleted from this table.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpPimStaticRPStatus		1.3.6.1.4.1.2272.1.8.16.4.1.5
The status of StaticRP.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	valid(1), invalid(2)

rcIpPimCurrBsr		1.3.6.1.4.1.2272.1.8.16.5
OBJECT IDENTIFIER

rcIpPimCurrBsrAddress		1.3.6.1.4.1.2272.1.8.16.5.1
Current BSR address
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpPimCurrBsrFragmentTag		1.3.6.1.4.1.2272.1.8.16.5.2
Current BSR Fragment Tag
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpPimCurrBsrHashMask		1.3.6.1.4.1.2272.1.8.16.5.3
Current BSR Hash Mask value
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpPimCurrBsrPriority		1.3.6.1.4.1.2272.1.8.16.5.4
Current BSR Priority
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpPimCurrBsrBootStrapTimer		1.3.6.1.4.1.2272.1.8.16.5.5
Current BSR Boot Strap Timer
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpPimVirtualNbrTable		1.3.6.1.4.1.2272.1.8.16.6
Table listing the router's virtual PIM neighbors
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpPimVirtualNbrEntry

rcIpPimVirtualNbrEntry		1.3.6.1.4.1.2272.1.8.16.6.1
An entry in the virtual PIM neighbors' table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpPimVirtualNbrEntry

rcIpPimVirtualNbrAddress		1.3.6.1.4.1.2272.1.8.16.6.1.1
The IP address of the virtual PIM neighbor for which this entry contains information.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rcIpPimVirtualNbrIfIndex		1.3.6.1.4.1.2272.1.8.16.6.1.2
The value of ifIndex for the PIM interface in which this virtual neighbor is created. This value is mandatory while trying to create a virtual PIM neighbor.
Status: current	Access: read-create
OBJECT-TYPE
	InterfaceIndex

rcIpPimVirtualNbrRowStatus		1.3.6.1.4.1.2272.1.8.16.6.1.3
To create/delete an entry in the virtual PIM neighbors' table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcIpMulticastArpTable		1.3.6.1.4.1.2272.1.8.17
IP Multicast Arp table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpMulticastArpEntry

rcIpMulticastArpEntry		1.3.6.1.4.1.2272.1.8.17.1
An entry of Ip Multicast Arp Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpMulticastArpEntry

rcIpMulticastArpVlanId		1.3.6.1.4.1.2272.1.8.17.1.1
vlan id
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

rcIpMulticastArpMacAddress		1.3.6.1.4.1.2272.1.8.17.1.2
multicast mac address
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rcIpMulticastArpIpAddress		1.3.6.1.4.1.2272.1.8.17.1.3
multicast ip address
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpMulticastArpPorts		1.3.6.1.4.1.2272.1.8.17.1.4
ports within a particular vlan
Status: current	Access: read-write
OBJECT-TYPE
	PortSet

rcIpMulticastArpNumMltIds		1.3.6.1.4.1.2272.1.8.17.1.5
number of mlt ids
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpMulticastArpMltIds		1.3.6.1.4.1.2272.1.8.17.1.6
mlt id
Status: current	Access: read-write
OBJECT-TYPE
	IdList

rcIpMulticastArpRowStatus		1.3.6.1.4.1.2272.1.8.17.1.7
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpMulticastTable		1.3.6.1.4.1.2272.1.8.18
Ip multicast table.
Status: obsolete	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpMulticastEntry

rcIpMulticastEntry		1.3.6.1.4.1.2272.1.8.18.1
Entry containing Proprietary Ip Multicast information.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	RcIpMulticastEntry

rcIpMulticastIfIndex		1.3.6.1.4.1.2272.1.8.18.1.1
IfIndex.
Status: deprecated	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcIpMulticastMulticastIp		1.3.6.1.4.1.2272.1.8.18.1.2
IP Address on this IfIndex to be used for all Multicast protocols running on this interface.
Status: deprecated	Access: read-write
OBJECT-TYPE
	IpAddress

rcIpCops		1.3.6.1.4.1.2272.1.8.19
OBJECT IDENTIFIER

rcCopsGlobalEnable		1.3.6.1.4.1.2272.1.8.19.1
Cops feature enable/disable
Status: deprecated	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpRipInterface		1.3.6.1.4.1.2272.1.8.20
OBJECT IDENTIFIER

rcIpRipInterfaceTable		1.3.6.1.4.1.2272.1.8.20.1
IP Rip Interface table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpRipInterfaceEntry

rcIpRipInterfaceEntry		1.3.6.1.4.1.2272.1.8.20.1.1
An entry of Ip Rip Interface Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpRipInterfaceEntry

rcIpRipInterfaceAddress		1.3.6.1.4.1.2272.1.8.20.1.1.1
Ip Address
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpRipInterfaceIfIndex		1.3.6.1.4.1.2272.1.8.20.1.1.2
Rip Interface If Index.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcIpRipInterfaceRipEnable		1.3.6.1.4.1.2272.1.8.20.1.1.3
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpRipInterfaceAccDefRte		1.3.6.1.4.1.2272.1.8.20.1.1.4
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpRipInterfaceAdvDefRte		1.3.6.1.4.1.2272.1.8.20.1.1.5
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpRipInterfaceAutoAggregate		1.3.6.1.4.1.2272.1.8.20.1.1.6
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpRipInterfaceCost		1.3.6.1.4.1.2272.1.8.20.1.1.7
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcIpRipInterfaceListen		1.3.6.1.4.1.2272.1.8.20.1.1.8
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpRipInterfacePoison		1.3.6.1.4.1.2272.1.8.20.1.1.9
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpRipInterfaceSupply		1.3.6.1.4.1.2272.1.8.20.1.1.10
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpRipInterfaceTriggeredUpdate		1.3.6.1.4.1.2272.1.8.20.1.1.11
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpRipInterfaceInPolicy		1.3.6.1.4.1.2272.1.8.20.1.1.12
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rcIpRipInterfaceOutPolicy		1.3.6.1.4.1.2272.1.8.20.1.1.13
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rcIpRipInterfaceProxyAnnounceFlag		1.3.6.1.4.1.2272.1.8.20.1.1.14
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpRipInterfaceHolddown		1.3.6.1.4.1.2272.1.8.20.1.1.15
Used to indicate the rip holddown timer for this interface
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..360

rcIpRipInterfaceTimeout		1.3.6.1.4.1.2272.1.8.20.1.1.16
Used to indicate the rip timeout interval for this interface
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	15..259200

rcIpMulticastTimedPruneTable		1.3.6.1.4.1.2272.1.8.21
This feature provides the ability for the user to create (S,G) Forwarding Entries that would not be pruned until a configurable timer expires. This feature is targeted for Passport 8600/8800. Currently the timer value is set to 0.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpMulticastTimedPruneEntry

rcIpMulticastTimedPruneEntry		1.3.6.1.4.1.2272.1.8.21.1
An entry of Ip Multicast Timed Prune Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpMulticastTimedPruneEntry

rcIpMulticastTimedPruneGroupAddress		1.3.6.1.4.1.2272.1.8.21.1.1
This field indicates the IP Multicast Group Address associated with the IP multicast stream.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcIpMulticastTimedPruneSourceAddress		1.3.6.1.4.1.2272.1.8.21.1.2
This is the Source Subnet IP address of the sender of the IP multicast stream.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcIpMulticastTimedPruneSrcSubnetMask		1.3.6.1.4.1.2272.1.8.21.1.3
This is the Source Subnet Mask IP address of the sender of the IP multicast stream.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcIpMulticastTimedPruneAgingTimer		1.3.6.1.4.1.2272.1.8.21.1.4
This field represents the amount of time (in minutes) this timed prune entry will be kept in the forwarding table when there are no more receivers. After this timer expires, this timed prune entry would be treated as a normal DVMRP/PIM forwarding entry. Aging Timer value of 0 (infinite time) indicates this timed prune entry will not be deleted even when there are no more receivers.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcIpMulticastTimedPruneTimeLeft		1.3.6.1.4.1.2272.1.8.21.1.5
This read-only field represents the remaining time for which this timed prune entry will be kept in the forwarding table. After this timer expires, this timed prune entry would be treated as a normal DVMRP/PIM forwarding entry. 0 in this field indicates that this entry would not be aged out.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpMulticastTimedPruneLastActivity		1.3.6.1.4.1.2272.1.8.21.1.6
This read-only field represents the actual time since the traffic has come from this Source, Group pair.
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

rcIpMulticastTimedPruneRowStatus		1.3.6.1.4.1.2272.1.8.21.1.7
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpConfIcmpRdiscTable		1.3.6.1.4.1.2272.1.8.22
A table used to maintain ICMP Route discovery information for a particular interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpConfIcmpRdiscEntry

rcIpConfIcmpRdiscEntry		1.3.6.1.4.1.2272.1.8.22.1
Entry containing ICMP Rdisc information. An entry is automatically created in this table when routing is enabled for an interface -or- when an ip address is configured on an interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpConfIcmpRdiscEntry

rcIpConfIcmpRdiscIfIndex		1.3.6.1.4.1.2272.1.8.22.1.1
An unique value to identify a physical interface or a logical interface (VLAN).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

rcIpConfIcmpRdiscAdvAddress		1.3.6.1.4.1.2272.1.8.22.1.2
Advertisement address to which the route discovery advertisements transmitted on this interface.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcIpConfIcmpRdiscAdvFlag		1.3.6.1.4.1.2272.1.8.22.1.3
Flag to indicate whether or not the address is to be advertised on this interface.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpConfIcmpRdiscAdvLifetime		1.3.6.1.4.1.2272.1.8.22.1.4
The value to be placed in the lifetime field of Router Advertisements sent from the interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	4..9000

rcIpConfIcmpRdiscMaxAdvInterval		1.3.6.1.4.1.2272.1.8.22.1.5
The maximum time allowed between sending Router Advertisements from this interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	4..1800

rcIpConfIcmpRdiscMinAdvInterval		1.3.6.1.4.1.2272.1.8.22.1.6
The minimum time allowed between sending Router Advertisements from this interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	3..1800

rcIpConfIcmpRdiscPreferenceLevel		1.3.6.1.4.1.2272.1.8.22.1.7
Preferability of the router address as a default Router
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	-2147483648..2147483647

rcIpMulticastSoftwareForwarding		1.3.6.1.4.1.2272.1.8.23
OBJECT IDENTIFIER

rcIpMulticastSoftwareForwardingEnable		1.3.6.1.4.1.2272.1.8.23.1
Enable/Disable multicast software forwarding.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpMulticastSoftwareForwardingThreshold		1.3.6.1.4.1.2272.1.8.23.2
Threshold to switch from software forwarding to hardware forwarding. Unit = pkt per second
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

rcIpMrouteHw		1.3.6.1.4.1.2272.1.8.24
OBJECT IDENTIFIER

rcIpMrouteHwTable		1.3.6.1.4.1.2272.1.8.24.1
The (conceptual) table containing hardware entries of multicast routing information for all the Group Address.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpMrouteHwEntry

rcIpMrouteHwEntry		1.3.6.1.4.1.2272.1.8.24.1.1
An entry (conceptual row) containing hardware entries of multicast routing information for a particular Group Address.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpMrouteHwEntry

rcIpMrouteHwGroupAddress		1.3.6.1.4.1.2272.1.8.24.1.1.1
The IP multicast group address for which this entry contains multicast routing information.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpMrouteHwSubnet		1.3.6.1.4.1.2272.1.8.24.1.1.2
The network address from where the source is sending the stream of traffic for which this entry contains multicast routing information.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpMrouteHwInvlan		1.3.6.1.4.1.2272.1.8.24.1.1.3
The Ingress vlan Id from where the traffic is coming for which this entry contains multicast routing information.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4094

rcIpMrouteHwPruned		1.3.6.1.4.1.2272.1.8.24.1.1.4
This is to show weather the entry containing multicast routing information has received Prune message or not.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcIpMrouteHwIndex		1.3.6.1.4.1.2272.1.8.24.1.1.5
This Index value keep tracks of the hardware record that has been accessed for displaying the entry containing multicast routing information.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

rcIpMrouteHwPrunesTable		1.3.6.1.4.1.2272.1.8.24.2
The (conceptual) table containing prune entries of multicast routing information for the Group Address.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpMrouteHwPrunesEntry

rcIpMrouteHwPrunesEntry		1.3.6.1.4.1.2272.1.8.24.2.1
An entry (conceptual row) containing prune entries of multicast routing information for a particular Group Address.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpMrouteHwPrunesEntry

rcIpMrouteHwPrunesGroupAddress		1.3.6.1.4.1.2272.1.8.24.2.1.1
The IP multicast group address for which this entry contains multicast routing information.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpMrouteHwPrunesSubnet		1.3.6.1.4.1.2272.1.8.24.2.1.2
The network address from where the source is sending the stream of traffic for which this entry contains multicast routing information.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpMrouteHwPrunesInvlan		1.3.6.1.4.1.2272.1.8.24.2.1.3
The Ingress vlan Id from where the traffic is coming for which this entry contains multicast routing information.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4094

rcIpMrouteHwPrunesNeighbor		1.3.6.1.4.1.2272.1.8.24.2.1.4
The IpAddress from where the Prune message has been received.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpMrouteHwPrunesTimer		1.3.6.1.4.1.2272.1.8.24.2.1.5
This is to show how much time is left for this particular entry containing multicast routing information during which the graft message can be sent.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpMrouteHwSourcesTable		1.3.6.1.4.1.2272.1.8.24.3
The (conceptual) table containing source entries of multicast routing information for the Group Address.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpMrouteHwSourcesEntry

rcIpMrouteHwSourcesEntry		1.3.6.1.4.1.2272.1.8.24.3.1
An entry (conceptual row) containing source entries of multicast routing information for a particular Group Address.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpMrouteHwSourcesEntry

rcIpMrouteHwSourcesGroupAddress		1.3.6.1.4.1.2272.1.8.24.3.1.1
The IP multicast group address for which this entry contains multicast routing information.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpMrouteHwSourcesSubnet		1.3.6.1.4.1.2272.1.8.24.3.1.2
The network address from where the source is sending the stream of traffic for which this entry contains multicast routing information.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpMrouteHwSourcesInvlan		1.3.6.1.4.1.2272.1.8.24.3.1.3
The Ingress vlan Id from where the traffic is coming for which this entry contains multicast routing information.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4094

rcIpMrouteHwSourcesAddress		1.3.6.1.4.1.2272.1.8.24.3.1.4
The Source Address from where the stream of traffic is reaching the corresponding Group Address for which this entry contains multicast routing information.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpMrouteHwSourcesIngressPort		1.3.6.1.4.1.2272.1.8.24.3.1.5
The Ingress vlan ports from where the traffic is coming, for which this entry contains multicast routing information.
Status: current	Access: read-only
OBJECT-TYPE
	PortSet

rcIpMrouteHwEgressVlansTable		1.3.6.1.4.1.2272.1.8.24.4
The (conceptual) table containing egress vlan entries of multicast routing information for the Group Address.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpMrouteHwEgressVlansEntry

rcIpMrouteHwEgressVlansEntry		1.3.6.1.4.1.2272.1.8.24.4.1
An entry (conceptual row) containing egress vlan entries of multicast routing information for a particular Group Address.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpMrouteHwEgressVlansEntry

rcIpMrouteHwEgressVlansGroupAddress		1.3.6.1.4.1.2272.1.8.24.4.1.1
The IP multicast group address for which this entry contains multicast routing information.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpMrouteHwEgressVlansSubnet		1.3.6.1.4.1.2272.1.8.24.4.1.2
The network address from where the source is sending the stream of traffic for which this entry contains multicast routing information.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpMrouteHwEgressVlansInvlan		1.3.6.1.4.1.2272.1.8.24.4.1.3
The Ingress vlan Id from where the traffic is coming for which this entry contains multicast routing information.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4094

rcIpMrouteHwEgressVlansId		1.3.6.1.4.1.2272.1.8.24.4.1.4
The Egress vlan Id from where the traffic is going out for which this entry contains multicast routing information
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4094

rcIpMrouteHwEgressVlansPorts		1.3.6.1.4.1.2272.1.8.24.4.1.5
he Egress vlan ports from where the traffic is going out for which this entry contains multicast routing information.
Status: current	Access: read-only
OBJECT-TYPE
	PortSet

rcIpMrouteHwEgressVlansIndex		1.3.6.1.4.1.2272.1.8.24.4.1.6
This Index value keep tracks of the hardware record that has been accessed for displaying the entry containing multicast routing information.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

rcIpResourceUsage		1.3.6.1.4.1.2272.1.8.25
OBJECT IDENTIFIER

rcIpResourceUsageGlobal		1.3.6.1.4.1.2272.1.8.25.1
OBJECT IDENTIFIER

rcIpResourceUsageGlobalIngressRecInUse		1.3.6.1.4.1.2272.1.8.25.1.1
Used to get the Ingress Record Usage in the switch. (S-G usage).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..32767

rcIpResourceUsageGlobalEgressRecInUse		1.3.6.1.4.1.2272.1.8.25.1.2
Used to get the Egress Record Usage in the switch (pepstream count).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..32767

rcIpResourceUsageGlobalIngressThreshold		1.3.6.1.4.1.2272.1.8.25.1.3
Used to get the threshold count for Ingress records.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..32767

rcIpResourceUsageGlobalEgressThreshold		1.3.6.1.4.1.2272.1.8.25.1.4
Used to get threshold count for egress records.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..32767

rcIpResourceUsageGlobalSendTrapAndLog		1.3.6.1.4.1.2272.1.8.25.1.5
A means of alerting the user. If this bool is set, a message will be send to console and also a duReport will be logged.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpResourceUsageGlobalSendTrapOnly		1.3.6.1.4.1.2272.1.8.25.1.6
A means of alerting the user. If this bool is set, a message will be send to console.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpResourceUsageGlobalLogMsgOnly		1.3.6.1.4.1.2272.1.8.25.1.7
A means of alerting the user.If this bool is set, a duReport will be logged.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpRsmlt		1.3.6.1.4.1.2272.1.8.26
OBJECT IDENTIFIER

rcIpRsmltGlobal		1.3.6.1.4.1.2272.1.8.26.1
OBJECT IDENTIFIER

rcIpRsmltGlobalTableSize		1.3.6.1.4.1.2272.1.8.26.1.1
Route Smlt table size.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpRsmltEdgeSupportEnable		1.3.6.1.4.1.2272.1.8.26.1.2
Used to enable/disable RSMLT Edge Support feature
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpRsmltOperTable		1.3.6.1.4.1.2272.1.8.26.2
Route Smlt Table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpRsmltOperEntry

rcIpRsmltOperEntry		1.3.6.1.4.1.2272.1.8.26.2.1
An entry of Ip As Path Access List Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpRsmltOperEntry

rcIpRsmltOperIfIndex		1.3.6.1.4.1.2272.1.8.26.2.1.1
Route Smlt Oper IfIndex.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcIpRsmltOperAdminStatus		1.3.6.1.4.1.2272.1.8.26.2.1.2
is a enable/disable flag.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpRsmltOperHoldDownTimer		1.3.6.1.4.1.2272.1.8.26.2.1.3
Timer value, the range of value is from 0 to 3600.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..3600

rcIpRsmltOperHoldDownTimeRemaining		1.3.6.1.4.1.2272.1.8.26.2.1.4
The time value that indicate how much time remaining of HoldDownTimer.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..3600

rcIpRsmltOperHoldUpTimer		1.3.6.1.4.1.2272.1.8.26.2.1.5
The range of value 0 to 3600 or 9999. 9999 means infinity.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..3600 | 9999

rcIpRsmltOperHoldUpTimeRemaining		1.3.6.1.4.1.2272.1.8.26.2.1.6
The time value that indicate how much time remaining of HoldUpTimer.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..3600 | 9999

rcIpRsmltOperIpAddr		1.3.6.1.4.1.2272.1.8.26.2.1.7
IP Interface with RSMLT on.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpRsmltOperOperStatus		1.3.6.1.4.1.2272.1.8.26.2.1.8
The operation status of Rsmlt, up or down.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2)

rcIpRsmltOperSmltId		1.3.6.1.4.1.2272.1.8.26.2.1.9
The id range for SMLT is 1-32.
Status: current	Access: read-only
OBJECT-TYPE
	IdList

rcIpRsmltOperSltId		1.3.6.1.4.1.2272.1.8.26.2.1.10
The id range for SLT is 1-512.
Status: current	Access: read-only
OBJECT-TYPE
	IdList

rcIpRsmltOperVlanId		1.3.6.1.4.1.2272.1.8.26.2.1.11
Vlan id.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4093

rcIpRsmltOperMacAddr		1.3.6.1.4.1.2272.1.8.26.2.1.12
Mac Address.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rcIpRsmltOperRowStatus		1.3.6.1.4.1.2272.1.8.26.2.1.13
Row Status.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpRsmltOperVrfId		1.3.6.1.4.1.2272.1.8.26.2.1.14
Indicates the Virtual Router to which the RSMLT Oper instance belongs.
Status: current	Access: read-only
OBJECT-TYPE
	VrfIdentifier

rcIpRsmltOperVrfName		1.3.6.1.4.1.2272.1.8.26.2.1.15
Name of the Virtual Router to which the RSMLT Oper instance belongs.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString	Size(0..64)

rcIpRsmltPeerTable		1.3.6.1.4.1.2272.1.8.26.3
Route Smlt Table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpRsmltPeerEntry

rcIpRsmltPeerEntry		1.3.6.1.4.1.2272.1.8.26.3.1
An entry of Ip As Path Access List Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpRsmltPeerEntry

rcIpRsmltPeerIfIndex		1.3.6.1.4.1.2272.1.8.26.3.1.1
Route Smlt Oper IfIndex.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcIpRsmltPeerAdminStatus		1.3.6.1.4.1.2272.1.8.26.3.1.2
is a enable/disable flag.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcIpRsmltPeerHoldDownTimer		1.3.6.1.4.1.2272.1.8.26.3.1.3
Timer value, the range of value is from 0 to 3600.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..3600

rcIpRsmltPeerHoldDownTimeRemaining		1.3.6.1.4.1.2272.1.8.26.3.1.4
The time value that indicate how much time remaining of HoldDownTimer.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..3600

rcIpRsmltPeerHoldUpTimer		1.3.6.1.4.1.2272.1.8.26.3.1.5
The range of value 0 to 3600 or 9999. 9999 means infinity.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..3600 | 9999

rcIpRsmltPeerHoldUpTimeRemaining		1.3.6.1.4.1.2272.1.8.26.3.1.6
The time value that indicate how much time remaining of HoldUpTimer.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..3600 | 9999

rcIpRsmltPeerIpAddr		1.3.6.1.4.1.2272.1.8.26.3.1.7
IP Interface with RSMLT on.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpRsmltPeerOperStatus		1.3.6.1.4.1.2272.1.8.26.3.1.8
The operation status of Rsmlt, up or down.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2)

rcIpRsmltPeerSmltId		1.3.6.1.4.1.2272.1.8.26.3.1.9
The id range for SMLT is 1-32.
Status: current	Access: read-only
OBJECT-TYPE
	IdList

rcIpRsmltPeerSltId		1.3.6.1.4.1.2272.1.8.26.3.1.10
The id range for SLT is 1-512.
Status: current	Access: read-only
OBJECT-TYPE
	IdList

rcIpRsmltPeerVlanId		1.3.6.1.4.1.2272.1.8.26.3.1.11
Vlan id.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4093

rcIpRsmltPeerMacAddr		1.3.6.1.4.1.2272.1.8.26.3.1.12
Mac Address.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rcIpRsmltPeerVrfId		1.3.6.1.4.1.2272.1.8.26.3.1.13
Indicates the Virtual Router to which the RSMLT Peer instance belongs.
Status: current	Access: read-only
OBJECT-TYPE
	VrfIdentifier

rcIpRsmltPeerVrfName		1.3.6.1.4.1.2272.1.8.26.3.1.14
Name of the Virtual Router to which the RSMLT Peer instance belongs.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString	Size(0..64)

rcIpRsmltEdgePeerTable		1.3.6.1.4.1.2272.1.8.26.4
RSMLT Edge Support Peer Info table. This table consists of the RSMLT Peers for which the switch will act as a PeerForwarder.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpRsmltEdgePeerEntry

rcIpRsmltEdgePeerEntry		1.3.6.1.4.1.2272.1.8.26.4.1
RSMLT Edge Support Peer Info Entry
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpRsmltEdgePeerEntry

rcIpRsmltEdgeVlanId		1.3.6.1.4.1.2272.1.8.26.4.1.1
A value that uniquely identifies the Virtual LAN associated with this entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..4094

rcIpRsmltEdgePeerIpAddress		1.3.6.1.4.1.2272.1.8.26.4.1.2
IP address of the Peer RSMLT Interface.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpRsmltEdgePeerMacAddress		1.3.6.1.4.1.2272.1.8.26.4.1.3
The MAC address of the Peer RSMLT interface.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rcIpRsmltEdgePeerVrfId		1.3.6.1.4.1.2272.1.8.26.4.1.4
Indicates the Virtual Router to which the RSMLT Edge Peer instance belongs.
Status: current	Access: read-only
OBJECT-TYPE
	VrfIdentifier

rcIpRsmltEdgePeerVrfName		1.3.6.1.4.1.2272.1.8.26.4.1.5
Name of the Virtual Router to which the RSMLT Edge Peer instance belongs.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString	Size(0..64)

rcIpv6RsmltOperTable		1.3.6.1.4.1.2272.1.8.26.5
Route Smlt Table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpv6RsmltOperEntry

rcIpv6RsmltOperEntry		1.3.6.1.4.1.2272.1.8.26.5.1
A local IPv6 RSMLT entry
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpv6RsmltOperEntry

rcIpv6RsmltOperIfIndex		1.3.6.1.4.1.2272.1.8.26.5.1.1
Route Smlt Oper IfIndex.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

rcIpv6RsmltOperIpv6Addr		1.3.6.1.4.1.2272.1.8.26.5.1.2
IPv6 Interface with RSMLT on.
Status: current	Access: not-accessible
OBJECT-TYPE
	Ipv6Address

rcIpv6RsmltOperIpv6PrefixLength		1.3.6.1.4.1.2272.1.8.26.5.1.3
IPv6 Prefix Length.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..128

rcIpv6RsmltOperAdminStatus		1.3.6.1.4.1.2272.1.8.26.5.1.4
is a enable/disable flag.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpv6RsmltOperHoldDownTimer		1.3.6.1.4.1.2272.1.8.26.5.1.5
Timer value, the range of value is from 0 to 3600.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..3600

rcIpv6RsmltOperHoldDownTimeRemaining		1.3.6.1.4.1.2272.1.8.26.5.1.6
The time value that indicate how much time remaining of HoldDownTimer.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..3600

rcIpv6RsmltOperHoldUpTimer		1.3.6.1.4.1.2272.1.8.26.5.1.7
The range of value 0 to 3600 or 9999. 9999 means infinity.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..3600 | 9999

rcIpv6RsmltOperHoldUpTimeRemaining		1.3.6.1.4.1.2272.1.8.26.5.1.8
The time value that indicate how much time remaining of HoldUpTimer.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..3600 | 9999

rcIpv6RsmltOperOperStatus		1.3.6.1.4.1.2272.1.8.26.5.1.9
The operation status of Rsmlt, up or down.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2)

rcIpv6RsmltOperSmltId		1.3.6.1.4.1.2272.1.8.26.5.1.10
The id range for SMLT is 1-32.
Status: current	Access: read-only
OBJECT-TYPE
	IdList

rcIpv6RsmltOperSltId		1.3.6.1.4.1.2272.1.8.26.5.1.11
The id range for SLT is 1-512.
Status: current	Access: read-only
OBJECT-TYPE
	IdList

rcIpv6RsmltOperVlanId		1.3.6.1.4.1.2272.1.8.26.5.1.12
Vlan id.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..4093

rcIpv6RsmltOperMacAddr		1.3.6.1.4.1.2272.1.8.26.5.1.13
Mac Address.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rcIpv6RsmltOperVrfId		1.3.6.1.4.1.2272.1.8.26.5.1.14
Indicates the Virtual Router to which the RSMLT Oper instance belongs.
Status: current	Access: read-only
OBJECT-TYPE
	VrfIdentifier

rcIpv6RsmltOperVrfName		1.3.6.1.4.1.2272.1.8.26.5.1.15
Name of the Virtual Router to which the RSMLT Oper instance belongs.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString	Size(0..64)

rcIpv6RsmltPeerTable		1.3.6.1.4.1.2272.1.8.26.6
Route Smlt Peer Table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpv6RsmltPeerEntry

rcIpv6RsmltPeerEntry		1.3.6.1.4.1.2272.1.8.26.6.1
An entry of Ip As Path Access List Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpv6RsmltPeerEntry

rcIpv6RsmltPeerIfIndex		1.3.6.1.4.1.2272.1.8.26.6.1.1
Route Smlt Oper IfIndex.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

rcIpv6RsmltPeerIpv6Addr		1.3.6.1.4.1.2272.1.8.26.6.1.2
IP Interface with RSMLT on.
Status: current	Access: not-accessible
OBJECT-TYPE
	Ipv6Address

rcIpv6RsmltPeerIpv6PrefixLength		1.3.6.1.4.1.2272.1.8.26.6.1.3
IPv6 Prefix Length
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..128

rcIpv6RsmltPeerAdminStatus		1.3.6.1.4.1.2272.1.8.26.6.1.4
is a enable/disable flag.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcIpv6RsmltPeerHoldDownTimer		1.3.6.1.4.1.2272.1.8.26.6.1.5
Timer value, the range of value is from 0 to 3600.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..3600

rcIpv6RsmltPeerHoldDownTimeRemaining		1.3.6.1.4.1.2272.1.8.26.6.1.6
The time value that indicate how much time remaining of HoldDownTimer.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..3600

rcIpv6RsmltPeerHoldUpTimer		1.3.6.1.4.1.2272.1.8.26.6.1.7
The range of value 0 to 3600 or 9999. 9999 means infinity.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..3600 | 9999

rcIpv6RsmltPeerHoldUpTimeRemaining		1.3.6.1.4.1.2272.1.8.26.6.1.8
The time value that indicate how much time remaining of HoldUpTimer.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..3600 | 9999

rcIpv6RsmltPeerOperStatus		1.3.6.1.4.1.2272.1.8.26.6.1.9
The operation status of Rsmlt, up or down.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2)

rcIpv6RsmltPeerSmltId		1.3.6.1.4.1.2272.1.8.26.6.1.10
The id range for SMLT is 1-32.
Status: current	Access: read-only
OBJECT-TYPE
	IdList

rcIpv6RsmltPeerSltId		1.3.6.1.4.1.2272.1.8.26.6.1.11
The id range for SLT is 1-512.
Status: current	Access: read-only
OBJECT-TYPE
	IdList

rcIpv6RsmltPeerVlanId		1.3.6.1.4.1.2272.1.8.26.6.1.12
Vlan id.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..4093

rcIpv6RsmltPeerMacAddr		1.3.6.1.4.1.2272.1.8.26.6.1.13
Mac Address.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rcIpv6RsmltPeerVrfId		1.3.6.1.4.1.2272.1.8.26.6.1.14
Indicates the Virtual Router to which the RSMLT Peer instance belongs.
Status: current	Access: read-only
OBJECT-TYPE
	VrfIdentifier

rcIpv6RsmltPeerVrfName		1.3.6.1.4.1.2272.1.8.26.6.1.15
Name of the Virtual Router to which the RSMLT Peer instance belongs.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString	Size(0..64)

rcIpv6RsmltEdgePeerTable		1.3.6.1.4.1.2272.1.8.26.7
RSMLT Edge Support Peer Info table. This table consists of the RSMLT Peers for which the switch will act as a PeerForwarder.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpv6RsmltEdgePeerEntry

rcIpv6RsmltEdgePeerEntry		1.3.6.1.4.1.2272.1.8.26.7.1
RSMLT Edge Support Peer Info Entry
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpv6RsmltEdgePeerEntry

rcIpv6RsmltEdgePeerVlanId		1.3.6.1.4.1.2272.1.8.26.7.1.1
A value that uniquely identifies the Virtual LAN associated with this entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..4094

rcIpv6RsmltEdgePeerIpv6Address		1.3.6.1.4.1.2272.1.8.26.7.1.2
IP address of the Peer RSMLT Interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	Ipv6Address

rcIpv6RsmltEdgePeerIpv6PrefixLength		1.3.6.1.4.1.2272.1.8.26.7.1.3
If set then this prefix can be used for address autoconfig, passed opaquely to Infinity
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..128

rcIpv6RsmltEdgePeerMacAddress		1.3.6.1.4.1.2272.1.8.26.7.1.4
The MAC address of the Peer RSMLT interface.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rcIpv6RsmltEdgePeerVrfId		1.3.6.1.4.1.2272.1.8.26.7.1.5
Indicates the Virtual Router to which the RSMLT Edge Peer instance belongs.
Status: current	Access: read-only
OBJECT-TYPE
	VrfIdentifier

rcIpv6RsmltEdgePeerVrfName		1.3.6.1.4.1.2272.1.8.26.7.1.6
Name of the Virtual Router to which the RSMLT Edge Peer instance belongs.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString	Size(0..64)

rcIpv6RsmltEdgePeerIsRaPrefix		1.3.6.1.4.1.2272.1.8.26.7.1.7
True if this is a Router Advertisement prefix, False if this is a global address.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcIpv6RsmltEdgePeerConfType		1.3.6.1.4.1.2272.1.8.26.7.1.8
Type of configured address, passed opaquely to Infinity
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..128

rcIpv6RsmltEdgePeerNoAdvertise		1.3.6.1.4.1.2272.1.8.26.7.1.9
True if advertisement of this prefix is disabled, passed opaquely to Infinity
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcIpv6RsmltEdgePeerOspf6Advertise		1.3.6.1.4.1.2272.1.8.26.7.1.10
True if OSPFv3 advertisement of this prefix is enabled, passed opaquely to Infinity
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcIpv6RsmltEdgePeerPrefCandidate		1.3.6.1.4.1.2272.1.8.26.7.1.11
True if address is considered for preferred selection, passed opaquely to Infinity
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcIpv6RsmltEdgePeerPfxValidLife		1.3.6.1.4.1.2272.1.8.26.7.1.12
Valid lifetime in seconds, passed opaquely to Infinity
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpv6RsmltEdgePeerPfxPrefLife		1.3.6.1.4.1.2272.1.8.26.7.1.13
Preferred lifetime in seconds, passed opaquely to Infinity
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpv6RsmltEdgePeerPfxOnLinkFlag		1.3.6.1.4.1.2272.1.8.26.7.1.14
If set then this prefix can be used for onlink determination, passed opaquely to Infinity
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcIpv6RsmltEdgePeerPfxAutoFlag		1.3.6.1.4.1.2272.1.8.26.7.1.15
If set then this prefix can be used for address autoconfig, passed opaquely to Infinity
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcIpGenPolicy		1.3.6.1.4.1.2272.1.8.100
OBJECT IDENTIFIER

rcIpAsPathAccessListTableSize		1.3.6.1.4.1.2272.1.8.100.1
table size
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpAsPathAccessListTable		1.3.6.1.4.1.2272.1.8.100.2
IP As Path Access List table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpAsPathAccessListEntry

rcIpAsPathAccessListEntry		1.3.6.1.4.1.2272.1.8.100.2.1
An entry of Ip As Path Access List Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpAsPathAccessListEntry

rcIpAsPathAccessListId		1.3.6.1.4.1.2272.1.8.100.2.1.1
Path Access List entry Id.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1024

rcIpAsPathAccessListMemberId		1.3.6.1.4.1.2272.1.8.100.2.1.2
frq. at which hello sent.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

rcIpAsPathAccessListMode		1.3.6.1.4.1.2272.1.8.100.2.1.3
Path Access List Mode, permit or deny.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	permit(1), deny(2)

rcIpAsPathAccessListAsRegularExpression		1.3.6.1.4.1.2272.1.8.100.2.1.4
IP Path Access List Regular Expression
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..256)

rcIpAsPathAccessListRowStatus		1.3.6.1.4.1.2272.1.8.100.2.1.5
Table row status.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpCommunityAccessListTableSize		1.3.6.1.4.1.2272.1.8.100.3
table size
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpCommunityAccessListTable		1.3.6.1.4.1.2272.1.8.100.4
IP CommunityAccess List table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpCommunityAccessListEntry

rcIpCommunityAccessListEntry		1.3.6.1.4.1.2272.1.8.100.4.1
An entry of Ip CommunityAccess List Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpCommunityAccessListEntry

rcIpCommunityAccessListId		1.3.6.1.4.1.2272.1.8.100.4.1.1
IP CommunityAccess entry List Id
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1024

rcIpCommunityAccessListMemberId		1.3.6.1.4.1.2272.1.8.100.4.1.2
frq. at which hello sent.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

rcIpCommunityAccessListMode		1.3.6.1.4.1.2272.1.8.100.4.1.3
IP Community Access List Mode, permit or deny.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	permit(1), deny(2)

rcIpCommunityAccessListCommunity		1.3.6.1.4.1.2272.1.8.100.4.1.4
IP Community Access List Community string.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..256)

rcIpCommunityAccessListRowStatus		1.3.6.1.4.1.2272.1.8.100.4.1.5
IP Community Access Table Row Status.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpAccessListTableSize		1.3.6.1.4.1.2272.1.8.100.5
table size
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpAccessListTable		1.3.6.1.4.1.2272.1.8.100.6
IP Access List table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpAccessListEntry

rcIpAccessListEntry		1.3.6.1.4.1.2272.1.8.100.6.1
An entry of Ip Access List Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpAccessListEntry

rcIpAccessListId		1.3.6.1.4.1.2272.1.8.100.6.1.1
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..99

rcIpAccessListMode		1.3.6.1.4.1.2272.1.8.100.6.1.2
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	permit(1), deny(2)

rcIpAccessListNetwork		1.3.6.1.4.1.2272.1.8.100.6.1.3
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcIpAccessListNetworkMask		1.3.6.1.4.1.2272.1.8.100.6.1.4
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcIpAccessListName		1.3.6.1.4.1.2272.1.8.100.6.1.5
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rcIpAccessListRowStatus		1.3.6.1.4.1.2272.1.8.100.6.1.6
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpExtendedAccessListTableSize		1.3.6.1.4.1.2272.1.8.100.7
table size
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpExtendedAccessListTable		1.3.6.1.4.1.2272.1.8.100.8
IP Extended Access List table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpExtendedAccessListEntry

rcIpExtendedAccessListEntry		1.3.6.1.4.1.2272.1.8.100.8.1
An entry of Ip Extended Access List Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpExtendedAccessListEntry

rcIpExtendedAccessListId		1.3.6.1.4.1.2272.1.8.100.8.1.1
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	100..199

rcIpExtendedAccessListMode		1.3.6.1.4.1.2272.1.8.100.8.1.2
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	permit(1), deny(2)

rcIpExtendedAccessListNetwork		1.3.6.1.4.1.2272.1.8.100.8.1.3
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpExtendedAccessListNetworkWildCard		1.3.6.1.4.1.2272.1.8.100.8.1.4
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpExtendedAccessListNetworkMask		1.3.6.1.4.1.2272.1.8.100.8.1.5
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpExtendedAccessListNetworkMaskWildCard		1.3.6.1.4.1.2272.1.8.100.8.1.6
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpExtendedAccessListName		1.3.6.1.4.1.2272.1.8.100.8.1.7
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rcIpExtendedAccessListRowStatus		1.3.6.1.4.1.2272.1.8.100.8.1.8
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpPrefixListTableSize		1.3.6.1.4.1.2272.1.8.100.9
table size
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpPrefixListTable		1.3.6.1.4.1.2272.1.8.100.10
IP Prefix List table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpPrefixListEntry

rcIpPrefixListEntry		1.3.6.1.4.1.2272.1.8.100.10.1
An entry of Ip Prefix List Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpPrefixListEntry

rcIpPrefixListId		1.3.6.1.4.1.2272.1.8.100.10.1.1
ListId
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

rcIpPrefixListPrefix		1.3.6.1.4.1.2272.1.8.100.10.1.2
Is a member of a specific prefix list. Adding the prefix to the given prefix list
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpPrefixListPrefixMaskLen		1.3.6.1.4.1.2272.1.8.100.10.1.3
prefix mask length
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..32

rcIpPrefixListMaskLenFrom		1.3.6.1.4.1.2272.1.8.100.10.1.4
used with mask len
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..32

rcIpPrefixListMaskLenUpto		1.3.6.1.4.1.2272.1.8.100.10.1.5
used with mask len
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..32

rcIpPrefixListName		1.3.6.1.4.1.2272.1.8.100.10.1.6
list name
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(1..64)

rcIpPrefixListRowStatus		1.3.6.1.4.1.2272.1.8.100.10.1.7
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpRoutePolicyTableSize		1.3.6.1.4.1.2272.1.8.100.11
table size
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpRoutePolicyApply		1.3.6.1.4.1.2272.1.8.100.12
Used to apply Ip Route Policy
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpRoutePolicyTable		1.3.6.1.4.1.2272.1.8.100.13
IP Route Map table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpRoutePolicyEntry

rcIpRoutePolicyEntry		1.3.6.1.4.1.2272.1.8.100.13.1
An entry of Ip Route Map Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpRoutePolicyEntry

rcIpRoutePolicyId		1.3.6.1.4.1.2272.1.8.100.13.1.1
Index used to identify a group of policies in the route policy tableRoute map id
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

rcIpRoutePolicySequenceNumber		1.3.6.1.4.1.2272.1.8.100.13.1.2
second index used to identify a specific policy with in the route policy group (grouped by Id). This field allows users to specify different MATCH, SET parameters and an action.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

rcIpRoutePolicyName		1.3.6.1.4.1.2272.1.8.100.13.1.3
Is used to group a set of policies with different sequence number. Id & Name have one-on-one relationship. Different policy groups can contain same sequence number, whereas with in a group the sequence number must be different.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(1..64)

rcIpRoutePolicyEnable		1.3.6.1.4.1.2272.1.8.100.13.1.4
Value specified here indicate whether this policy is enabled or not. If disabled policy sould not be used.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpRoutePolicyMode		1.3.6.1.4.1.2272.1.8.100.13.1.5
specifies the action to be taken when this policy is selected for a specific route. This can be permit or deny or continue. Permit indicates allow the route, deny indicates ignore the route. Continue means continue checking the next match criteria set in the next policy seq, if none take the default action in the given context.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	permit(1), deny(2)

rcIpRoutePolicyMatchProtocol		1.3.6.1.4.1.2272.1.8.100.13.1.6
Match protocol. Used for RIP and DVMRP announce policy only. Value is one of multiple (logical 'OR) of the following values: direct(1), static(2), rip(4), ospf(8), ebgp(16), dvmrp(32), ibgp(64), isis(128), any(255) direct(1): enables direct match-protocol static(2): enables static match-protocol rip(4): enables rip match-protocol ospf(8): enables ospf match-protocol ebgp(16): enables ebgp match-protocol dvmrp(32): enables dvmrp match-protocol ibgp(64): enables ibgp match-protocol isis(128): enables isis match-protocol any(255): enables all match-protocols
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..255

rcIpRoutePolicyMatchAsPath		1.3.6.1.4.1.2272.1.8.100.13.1.7
Applicable to BGP protocol only. Match the BGP autonomous system path. This will override the BGP neighbor filter list info.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rcIpRoutePolicyMatchCommunity		1.3.6.1.4.1.2272.1.8.100.13.1.8
Applicable to BGP protocol only. Filter incoming/outgoing updates based on communities.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rcIpRoutePolicyMatchCommunityExact		1.3.6.1.4.1.2272.1.8.100.13.1.9
If enabled indicates the match has be an exact (i.e., all of the communities specified in the path has to be matched).
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpRoutePolicyMatchNetwork		1.3.6.1.4.1.2272.1.8.100.13.1.10
can specify one or more prefix list name or id(s)
Status: current	Access: read-write
OBJECT-TYPE
	RcLongDisplayString	Size(0..259)

rcIpRoutePolicyMatchIpRouteSource		1.3.6.1.4.1.2272.1.8.100.13.1.11
In case of Rip routes this is equivalent to RipInterface. In case of DVMRP routes this is equivalent to DVMRP gateway. Can specify one or more prefix list name(s) or id(s) seperated by comma.
Status: current	Access: read-write
OBJECT-TYPE
	RcLongDisplayString	Size(0..259)

rcIpRoutePolicyMatchNextHop		1.3.6.1.4.1.2272.1.8.100.13.1.12
In case of Rip routes this is equivalent to RipInterface. In case of DVMRP routes this is equivalent to DVMRP gateway. Can specify one or more prefix list name(s) or id(s) seperated by comma.
Status: current	Access: read-write
OBJECT-TYPE
	RcLongDisplayString	Size(0..259)

rcIpRoutePolicyMatchInterface		1.3.6.1.4.1.2272.1.8.100.13.1.13
Match received interface. Only for rip routes. Ignored in all other cases.
Status: current	Access: read-write
OBJECT-TYPE
	RcLongDisplayString	Size(0..259)

rcIpRoutePolicyMatchRouteType		1.3.6.1.4.1.2272.1.8.100.13.1.14
For BGP this choice refers to locally generated routes external routes learned via ebgp nbr. For OSPF internal refers to intra and inter area routes (belongs to local autonomous system). External (type1|type2) refers to the routes learned from other ASs and imported as either type1 or type2. if type1/type2 is specified then match only type1/type2.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	any(0), local(1), internal(2), external(3), externaltype1(4), externaltype2(5), level1(6), level2(7)

rcIpRoutePolicyMatchMetric		1.3.6.1.4.1.2272.1.8.100.13.1.15
Match mec field in the incoming advertisement.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

rcIpRoutePolicyMatchTag		1.3.6.1.4.1.2272.1.8.100.13.1.16
specifies a list of tag(s), that will be used during the match criteria process.contains one or more tag values..
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rcIpRoutePolicySetRoutePreference		1.3.6.1.4.1.2272.1.8.100.13.1.17
if non-zero specifies the route preference value to be assigned to the routes that applies this policy.contains one or more tag values..
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

rcIpRoutePolicySetAsPath		1.3.6.1.4.1.2272.1.8.100.13.1.18
The AS path vaule to be used whether the SetAsPathMode is Tag or Prepend.as-path string..
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rcIpRoutePolicySetAsPathMode		1.3.6.1.4.1.2272.1.8.100.13.1.19
It can be either tag or prepend tag. applicable only while redistributing routes to BGP.Converts the tag of a route into AS path.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	tag(1), prepend(2)

rcIpRoutePolicySetAutomaticTag		1.3.6.1.4.1.2272.1.8.100.13.1.20
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpRoutePolicySetCommunityNumber		1.3.6.1.4.1.2272.1.8.100.13.1.21
this value can be a number (1..42949672000) or no-export or no-advertise. Applicable to BGP advertisments.community number.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rcIpRoutePolicySetCommunityMode		1.3.6.1.4.1.2272.1.8.100.13.1.22
this value can be either append or none unchanged - keep the community attribute in the route path as it is. none - remove the community in the route path additive - adds the community-number specified in SetCommunityNumber to the community list attribute. Applicable to BGP advertisments.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unchanged(0), none(1), append(2)

rcIpRoutePolicySetMetricTypeInternal		1.3.6.1.4.1.2272.1.8.100.13.1.23
Indicates to set the MED value for routes advertised to ebgp nbrs to the IGP metric value.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcIpRoutePolicySetMetric		1.3.6.1.4.1.2272.1.8.100.13.1.24
Value of the metric to be used while sending an update for the routes that match the matching criteria in this route policy. Default - 0 indicates the internal value defined for protocol
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

rcIpRoutePolicySetMetricType		1.3.6.1.4.1.2272.1.8.100.13.1.25
Metric type for the routes to be imported into OSPF routing protocol, which passed the matching criteria configured in this route policy.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	type1(1), type2(2), internal(3), external(4)

rcIpRoutePolicySetNextHop		1.3.6.1.4.1.2272.1.8.100.13.1.26
IpAddress of the next hop router. Ignored for DVMRP routes.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcIpRoutePolicySetOrigin		1.3.6.1.4.1.2272.1.8.100.13.1.27
igp/egp/incomplete Applicable to BGP protocol only. If not set uses the route origin from the Ip routing table (protocol).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unchanged(0), igp(1), egp(2), incomplete(3)

rcIpRoutePolicySetLocalPref		1.3.6.1.4.1.2272.1.8.100.13.1.28
this value will be used during route decision process in the BGP protocol. Applicable to BGP only.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcIpRoutePolicySetOriginEgpAs		1.3.6.1.4.1.2272.1.8.100.13.1.29
indicates the Remote autonomous sys number. Applicable to BGP only.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcIpRoutePolicySetTag		1.3.6.1.4.1.2272.1.8.100.13.1.30
Value to be used for setting tag of the destination routing protocol. If not specified forward the tag value in the source routing protocol. Value 0 indicates not set
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcIpRoutePolicySetWeight		1.3.6.1.4.1.2272.1.8.100.13.1.31
Should be using with match as-path condition. Weight value for the routing table. For BGP this value will override the weight configured through NetworkTableEntry or FilterListWeight or NeighborWeight. Used for BGP only.Value 0 indicates not set
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcIpRoutePolicySetInjectNetList		1.3.6.1.4.1.2272.1.8.100.13.1.32
specifies the prefix list to be used either for injecting the routes into the routing table or to include the networks in the advertisement. Ignored for DVMRP.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rcIpRoutePolicyRowStatus		1.3.6.1.4.1.2272.1.8.100.13.1.33
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpRoutePolicySetMask		1.3.6.1.4.1.2272.1.8.100.13.1.34
Set Mask Ip Address
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcIpRoutePolicyNssaPbit		1.3.6.1.4.1.2272.1.8.100.13.1.35
Set/Reset P bit in specified type 7 LSA. By default P bit is always set in case user set it to disable state for particular route policy than all type 7 LSAs associated with that route policy will have P bit cleared, with this intact NSSA ABR will not perform translation of these LSAs to type 5.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpRoutePolicyMatchVrf		1.3.6.1.4.1.2272.1.8.100.13.1.36
An array used to identify which source VRFs have leaked routes to the local VRF
Status: current	Access: read-write
OBJECT-TYPE
	IdList	Size(0..256)

rcIpRoutePolicyMatchExtCommunity		1.3.6.1.4.1.2272.1.8.100.13.1.37
Filter incoming/outgoing updates based on communities
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString

rcIpRoutePolicySetExtCommunity		1.3.6.1.4.1.2272.1.8.100.13.1.38
Set Extended-community string.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString

rcIpRoutePolicySetExtCommunityMode		1.3.6.1.4.1.2272.1.8.100.13.1.39
This value can be either additive, unchanged or overwrite.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	append(0), unchanged(1), overwrite(2)

rcIpRoutePolicyMatchLocalPref		1.3.6.1.4.1.2272.1.8.100.13.1.40
Match Local Prefix value.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

rcIpRoutePolicyMatchIpRouteDest		1.3.6.1.4.1.2272.1.8.100.13.1.41
to match route destination, one can specify one or more prefix list name(s) or id(s) separated by comma.
Status: current	Access: read-create
OBJECT-TYPE
	RcLongDisplayString	Size(0..259)

rcIpRoutePolicyMatchExtendedPref		1.3.6.1.4.1.2272.1.8.100.13.1.42
To associate extended ACL(access control list) with the route policy. User can associate one or multiple extended ACLs.
Status: current	Access: read-create
OBJECT-TYPE
	OCTET STRING	Size(1..1027)

rcIpRoutePolicyIpv6SetNextHop		1.3.6.1.4.1.2272.1.8.100.13.1.43
Address of the ipv6 next hop router. Ignored for DVMRP routes.
Status: current	Access: read-create
OBJECT-TYPE
	Ipv6Address

rcIpRedistributeTableSize		1.3.6.1.4.1.2272.1.8.100.14
table size
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpRedistributeApply		1.3.6.1.4.1.2272.1.8.100.15
Apply Ip Redistribution
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpRedistributeTable		1.3.6.1.4.1.2272.1.8.100.16
IP Redistribute table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpRedistributeEntry

rcIpRedistributeEntry		1.3.6.1.4.1.2272.1.8.100.16.1
An entry of Ip Redistribute Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpRedistributeEntry

rcIpRedistributeProtocol		1.3.6.1.4.1.2272.1.8.100.16.1.1
Protocol is any one of the dynamic routing protocol, which is interested in receiving the external routing info.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ospf(1), bgp(2), isis(3), ospfv3(4), vrf-ext(5)

rcIpRedistributeRouteSource		1.3.6.1.4.1.2272.1.8.100.16.1.2
equivalent to the owner field in the routing table. This field indicates that the protocol is interested in knowing/not-knowing the routes learned from this source.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	direct(1), static(2), rip(3), ospf(4), bgp(5), isis(6)

rcIpRedistributeEnable		1.3.6.1.4.1.2272.1.8.100.16.1.3
Enable/Disable. By default this is enabled.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpRedistributeMetric		1.3.6.1.4.1.2272.1.8.100.16.1.4
value of the metric to be announced in the advertisment. The Range specified is the range for ISIS for other protocols range is (0 .. 65535)
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

rcIpRedistributeMetricType		1.3.6.1.4.1.2272.1.8.100.16.1.5
specifies the type of the metric type, useful for OSPF and BGP only. In case of ISIS type1 is treated as internal and type2 is treated as external
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	type1(1), type2(2)

rcIpRedistributeMatchRouteType		1.3.6.1.4.1.2272.1.8.100.16.1.6
used to filter a route based on the route type. applicable to BGP.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	internal(1), external1(2), external2(3)

rcIpRedistributeSetTag		1.3.6.1.4.1.2272.1.8.100.16.1.7
Tag value to be set in the advertisment.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcIpRedistributeSubnets		1.3.6.1.4.1.2272.1.8.100.16.1.8
applicable to OSPF only. Indicates that all the subnets need to be advertised individually.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	allow(1), supress(2)

rcIpRedistributeRoutePolicy		1.3.6.1.4.1.2272.1.8.100.16.1.9
specify the route policy to achieve the final granularity in filtering to determine whether or not a specific route should be advertised to the given protocol.Route map name
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rcIpRedistributeASNumber		1.3.6.1.4.1.2272.1.8.100.16.1.10
Autonomous system number. Used only for the BGP protocol.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcIpRedistributeWeight		1.3.6.1.4.1.2272.1.8.100.16.1.11
used only for the BGP protocol.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcIpRedistributeDefaultOriginate		1.3.6.1.4.1.2272.1.8.100.16.1.12
indicates the given protocol will originate/advertise a default route.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcIpRedistributeRowStatus		1.3.6.1.4.1.2272.1.8.100.16.1.13
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpRedistributeLevel		1.3.6.1.4.1.2272.1.8.100.16.1.14
This is for ISIS only this sets the redistribute level. Set this to level2 to distribute the routes in L2 LSPs if the router is at level1 then setting redistribute at level2 does not have any significance.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	level2(2)

rcIpOspfInFilterTableSize		1.3.6.1.4.1.2272.1.8.100.17
table size
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpOspfInFilterApply		1.3.6.1.4.1.2272.1.8.100.18
Used to Apply Ip Ospf In Filter
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpOspfInFilterTable		1.3.6.1.4.1.2272.1.8.100.19
IP Ospf In Filter table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpOspfInFilterEntry

rcIpOspfInFilterEntry		1.3.6.1.4.1.2272.1.8.100.19.1
An entry of Ip Ospf In Filter Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpOspfInFilterEntry

rcIpOspfInFilterAdvertisingRtr		1.3.6.1.4.1.2272.1.8.100.19.1.1
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpOspfInFilterEnable		1.3.6.1.4.1.2272.1.8.100.19.1.2
IfIndex
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpOspfInFilterMetricType		1.3.6.1.4.1.2272.1.8.100.19.1.3
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	type1(1), type2(2), any(3)

rcIpOspfInFilterPolicyName		1.3.6.1.4.1.2272.1.8.100.19.1.4
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rcIpOspfInFilterRowStatus		1.3.6.1.4.1.2272.1.8.100.19.1.5
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpRoutePrefTableSize		1.3.6.1.4.1.2272.1.8.100.20
table size
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpRoutePrefTable		1.3.6.1.4.1.2272.1.8.100.21
IP Route Pref table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpRoutePrefEntry

rcIpRoutePrefEntry		1.3.6.1.4.1.2272.1.8.100.21.1
An entry of Ip Route Pref Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpRoutePrefEntry

rcIpRoutePrefProtocol		1.3.6.1.4.1.2272.1.8.100.21.1.1
Protocol
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	local(1), static(2), mpls(3), ospfIntra(4), ospfInter(5), isisLevel1(6), isisLevel2(7), ebgp(8), rip(9), ospfExternal1(10), ospfExternal2(11), ibgp(12), staticv6(13), ospfv3Intra(14), ospfv3Inter(15), ospfv3External1(16), ospfv3External2(17), spbmLevel1(18)

rcIpRoutePrefDefault		1.3.6.1.4.1.2272.1.8.100.21.1.2
Shows the default preference value for the given protocol.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..255

rcIpRoutePrefConfigured		1.3.6.1.4.1.2272.1.8.100.21.1.3
This value is configurable by the user
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

rcIpRedistributeInterVrfTable		1.3.6.1.4.1.2272.1.8.100.22
IP Redistribute table for Inter-VRFs
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpRedistributeInterVrfEntry

rcIpRedistributeInterVrfEntry		1.3.6.1.4.1.2272.1.8.100.22.1
An entry of Ip Redistribute Table.(new)
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpRedistributeInterVrfEntry

rcIpRedistributeInterVrfDstVrfId		1.3.6.1.4.1.2272.1.8.100.22.1.1
dst VRF id used in the redistribution
Status: current	Access: not-accessible
OBJECT-TYPE
	VrfIdentifier

rcIpRedistributeInterVrfProtocol		1.3.6.1.4.1.2272.1.8.100.22.1.2
Protocol is any one of the dynamic routing protocol, which is interested in receiving the external routing info.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	ospf(1), bgp(2), isis(3), vrf-ext(4), extranet(5), rip(6), ospfv3(10)

rcIpRedistributeInterVrfSrcVrfId		1.3.6.1.4.1.2272.1.8.100.22.1.3
src VRF id used in the redistribution
Status: current	Access: not-accessible
OBJECT-TYPE
	VrfIdentifier

rcIpRedistributeInterVrfRouteSource		1.3.6.1.4.1.2272.1.8.100.22.1.4
equivalent to the owner field in the routing table. This field indicates that the protocol is interested in knowing/not-knowing the routes learned from this source.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	direct(1), static(2), rip(3), ospf(4), bgp(5), extranet(6), v6direct(10), v6static(11), ospfv3(12), isis(13)

rcIpRedistributeInterVrfEnable		1.3.6.1.4.1.2272.1.8.100.22.1.5
Enable/Disable. By default this is enabled.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpRedistributeInterVrfMetric		1.3.6.1.4.1.2272.1.8.100.22.1.6
value of the metric to be announced in the advertisment
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

rcIpRedistributeInterVrfMetricType		1.3.6.1.4.1.2272.1.8.100.22.1.7
specifies the type of the metric type, useful for OSPF and BGP only.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	type1(1), type2(2)

rcIpRedistributeInterVrfMatchRouteType		1.3.6.1.4.1.2272.1.8.100.22.1.8
used to filter a route based on the route type. applicable to BGP.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	internal(1), external1(2), external2(3)

rcIpRedistributeInterVrfSetTag		1.3.6.1.4.1.2272.1.8.100.22.1.9
Tag value to be set in the advertisment.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcIpRedistributeInterVrfSubnets		1.3.6.1.4.1.2272.1.8.100.22.1.10
applicable to OSPF only. Indicates that all the subnets need to be advertised individually.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	allow(1), suppress(2)

rcIpRedistributeInterVrfRoutePolicy		1.3.6.1.4.1.2272.1.8.100.22.1.11
specify the route policy to achieve the final granularity in filtering to determine whether or not a specific route should be advertised to the given protocol.Route map name
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rcIpRedistributeInterVrfASNumber		1.3.6.1.4.1.2272.1.8.100.22.1.12
Autonomous system number. Used only for the BGP protocol.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcIpRedistributeInterVrfWeight		1.3.6.1.4.1.2272.1.8.100.22.1.13
used only for the BGP protocol.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcIpRedistributeInterVrfDefaultOriginate		1.3.6.1.4.1.2272.1.8.100.22.1.14
indicates the given protocol will originate/advertise a default route.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcIpExtCommunityAccessListTableSize		1.3.6.1.4.1.2272.1.8.100.23
IP Extended Community Access List table size.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpExtCommunityAccessListTable		1.3.6.1.4.1.2272.1.8.100.24
IP Extended Community Access List table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpExtCommunityAccessListEntry

rcIpExtCommunityAccessListEntry		1.3.6.1.4.1.2272.1.8.100.24.1
An entry of Ip Extended Community Access List Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpExtCommunityAccessListEntry

rcIpExtCommunityAccessListId		1.3.6.1.4.1.2272.1.8.100.24.1.1
IP extended Community Access List Id
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..1024

rcIpExtCommunityAccessListMemberId		1.3.6.1.4.1.2272.1.8.100.24.1.2
Member Id for the extended-community list to be added
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..65535

rcIpExtCommunityAccessListRTType		1.3.6.1.4.1.2272.1.8.100.24.1.3
The route target Type for IP Extended Community rule in the list
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(0), asnum(1), ipaddr(2)

rcIpExtCommunityAccessListRTAddress		1.3.6.1.4.1.2272.1.8.100.24.1.4
Extended community Ip address for the route-target type entry.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

rcIpExtCommunityAccessListRTAsNumber		1.3.6.1.4.1.2272.1.8.100.24.1.5
Extended community Asnumber for the route-target type entry.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..65535

rcIpExtCommunityAccessListRTAssignedNum		1.3.6.1.4.1.2272.1.8.100.24.1.6
Extended community assigned number for the route-target type entry.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..2147483647

rcIpExtCommunityAccessListSooType		1.3.6.1.4.1.2272.1.8.100.24.1.7
The site of origin Type for IP Extended Community Access List
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(0), asnum(1), ipaddr(2)

rcIpExtCommunityAccessListSooAddress		1.3.6.1.4.1.2272.1.8.100.24.1.8
Extended community Ip address for the site-of-origin type of entry.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

rcIpExtCommunityAccessListSooAsNumber		1.3.6.1.4.1.2272.1.8.100.24.1.9
Extended community AsNumber for the site-of-origin type of entry.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..65535

rcIpExtCommunityAccessListSooAssignedNum		1.3.6.1.4.1.2272.1.8.100.24.1.10
Extended community assigned number for the site-of-origin type of entry.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..2147483647

rcIpExtCommunityAccessListVrfId		1.3.6.1.4.1.2272.1.8.100.24.1.11
VrfId for the extended-community Access list.
Status: current	Access: read-create
OBJECT-TYPE
	VrfIdentifier

rcIpExtCommunityAccessListRowStatus		1.3.6.1.4.1.2272.1.8.100.24.1.12
IP Ext Community Table Row Status.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcIpRedistributeInterVrfRowStatus		1.3.6.1.4.1.2272.1.8.100.22.1.15
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpExtACLTable		1.3.6.1.4.1.2272.1.8.100.25
This table contains list of extended ACL (access control list) configuration. The extended ACL is used to filter SA (Source-Active) messages by matching both the source and destination address fields of a given packet.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpExtACLEntry

rcIpExtACLEntry		1.3.6.1.4.1.2272.1.8.100.25.1
An entry (conceptual row) representing a prefix of an ACL list. The ACL list is identified by the ACL name. User can add one or multiple prefixes to an ACL list. Empty ACL list is not allowed.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpExtACLEntry

rcIpExtACLPrefixSourceAddr		1.3.6.1.4.1.2272.1.8.100.25.1.1
This is the source address of the prefix.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rcIpExtACLPrefixSourceMask		1.3.6.1.4.1.2272.1.8.100.25.1.2
This is the source mask of the prefix.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rcIpExtACLPrefixDestinationAddr		1.3.6.1.4.1.2272.1.8.100.25.1.3
This is the destination address of the prefix.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rcIpExtACLPrefixDestinationMask		1.3.6.1.4.1.2272.1.8.100.25.1.4
This is a destination mask of the prefix.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rcIpExtACLPrefixName		1.3.6.1.4.1.2272.1.8.100.25.1.5
This is the extended ACL list to which the prefixes belongs. An extended ACL list must have one prefix at least.
Status: current	Access: not-accessible
OBJECT-TYPE
	SnmpAdminString	Size(1..64)

rcIpExtACLPrefixRowStatus		1.3.6.1.4.1.2272.1.8.100.25.1.6
Used to create/delete prefixes from ACL list.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcIpBgp		1.3.6.1.4.1.2272.1.8.101
OBJECT IDENTIFIER

rcIpBgpGeneralGroup		1.3.6.1.4.1.2272.1.8.101.1
OBJECT IDENTIFIER

rcIpBgpGeneralGroupLocalAs		1.3.6.1.4.1.2272.1.8.101.1.1
Local Autonomous system number
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..65535

rcIpBgpGeneralGroupAdminStatus		1.3.6.1.4.1.2272.1.8.101.1.2
Disable or Enable group administrative
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpBgpGeneralGroupDefaultMetric		1.3.6.1.4.1.2272.1.8.101.1.3
The default-metric is used in conjunction with the redistribute router configuration command to cause the bgp routing protocol to use this metric as MED
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..2147483647

rcIpBgpGeneralGroupDefaultLocalPreference		1.3.6.1.4.1.2272.1.8.101.1.4
Default local preference attribute value to be used
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..2147483647

rcIpBgpGeneralGroupDefaultInformationOriginate		1.3.6.1.4.1.2272.1.8.101.1.5
allows the redistribution of network 0.0.0.0 into BGP
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpBgpGeneralGroupBestPathMissingAsWorst		1.3.6.1.4.1.2272.1.8.101.1.6
Enable to consider a missing MED attribute in a path as having a value of infinity, making the path without a MED value the least desirable path. To return the router to the default (assign a value of 0 to the missing MED), set the value to disable.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpBgpGeneralGroupBestPathMedConfed		1.3.6.1.4.1.2272.1.8.101.1.7
To enable MED comparison among paths learned from confederation peers. Disable to prevent considering the MED attribute in comparing paths
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpBgpGeneralGroupIgnoreIllegalRouterId		1.3.6.1.4.1.2272.1.8.101.1.8
Configures BGP to overlook an illegal router ID. Enables or disable accepting a connection from a peer that sends its open message with a router ID of 0.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpBgpGeneralGroupAlwaysCompareMed		1.3.6.1.4.1.2272.1.8.101.1.9
Enable to allow the comparison of the Multi Exit Discriminator (MED) for paths from neighbors in different autonomous systems.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpBgpGeneralGroupAutoPeerRestart		1.3.6.1.4.1.2272.1.8.101.1.10
Enable the feature that automatically restarts the connection to a BGP peer when the connection goes down.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpBgpGeneralGroupAutoSummary		1.3.6.1.4.1.2272.1.8.101.1.11
Enable BGP to summarize networks based on class limlts (Class A,B,C networks).
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpBgpGeneralGroupSynchronization		1.3.6.1.4.1.2272.1.8.101.1.12
Enables and disables the router from accepting routes from BGP peers without waiting for an update from the IBGP.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpBgpGeneralGroupMaxEqualcostRoutes		1.3.6.1.4.1.2272.1.8.101.1.13
Sets the number of maximum number of equal-cost routes that can be stored in the routing table.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..8

rcIpBgpGeneralGroupIbgpReportImportRoute		1.3.6.1.4.1.2272.1.8.101.1.14
Configure BGP to report imported routes to an interior BGP peer.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpBgpGeneralGroupAggregate		1.3.6.1.4.1.2272.1.8.101.1.15
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpBgpGeneralGroupFlapDampEnable		1.3.6.1.4.1.2272.1.8.101.1.16
Enabled or Disabled
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpBgpGeneralGroupDebugMask		1.3.6.1.4.1.2272.1.8.101.1.17
value is one of multiple (logically by 'OR' of following value: none (0), error(1), packet(2), event(4), trace(8), warning(16), state(32), init(64), filter(128), update(256), all(511) all(511): Enables all debugging messages. none(0): Disables all debugging messages. error(1): Enables disolay of debug error messages. packet(2): Enables display of debug packet messages. event(4): Enables display of debug event messages. trace(8): Enables display debug trace messages. warning(16): Enables display debug warning messages. state(32): Enables display of debug state transtion messages. init(64): Enables display of debug initialization messages. filter(128): Enables display of debug messages related to filtering. update(256): Enables display of debug messages related to sending and receiving updates.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..511

rcIpBgpGeneralGroupTrapEnable		1.3.6.1.4.1.2272.1.8.101.1.18
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpBgpGeneralGroupQuickStart		1.3.6.1.4.1.2272.1.8.101.1.19
Enable the flag to avoid flap penalty and trigger the peer start event quickly
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpBgpGeneralGroupDeterministicMed		1.3.6.1.4.1.2272.1.8.101.1.20
Enable to allow the comparison of the Multi Exit Discriminator (MED) for paths from neighbors in same autonomous system.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpBgpGeneralGroupRouteRefresh		1.3.6.1.4.1.2272.1.8.101.1.21
Route Refresh for Bgp.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpBgpGeneralGroupRoutePolicyIn		1.3.6.1.4.1.2272.1.8.101.1.22
Route Policy Name that will be applied to all routes which enter the VRF table.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..64)

rcIpBgpGeneralGroupRoutePolicyOut		1.3.6.1.4.1.2272.1.8.101.1.23
Route policy name that will be applied to all routes which are sent out of this VRF instance.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..64)

rcIpBgpGeneralGroupDefaultInformationOriginateIpv6		1.3.6.1.4.1.2272.1.8.101.1.24
allows the redistribution of default ipv6 network into BGP
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpBgpGeneralGroupNewLocalAs		1.3.6.1.4.1.2272.1.8.101.1.25
Local Autonomous system number
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..4)

rcIpBgpGeneralGroup4ByteAs		1.3.6.1.4.1.2272.1.8.101.1.26
4 Byte As number enable
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpBgpGeneralGroupAsDot		1.3.6.1.4.1.2272.1.8.101.1.27
As number in Dot format
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpBgpAggregateTableSize		1.3.6.1.4.1.2272.1.8.101.2
Size of Aggregate Table
Status: deprecated	Access: read-only
OBJECT-TYPE
	Integer32

rcIpBgpAggregateTable		1.3.6.1.4.1.2272.1.8.101.3
To specify the list of aggregate prefixes to be created by the BGP routing process and the options to be used while aggregating.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpBgpAggregateEntry

rcIpBgpAggregateEntry		1.3.6.1.4.1.2272.1.8.101.3.1
An entry of rcIpBgp Aggregate Address In Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpBgpAggregateEntry

rcIpBgpAggregateAddress		1.3.6.1.4.1.2272.1.8.101.3.1.1
Prefix to create an aggregate address in BGP routing table.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpBgpAggregateMask		1.3.6.1.4.1.2272.1.8.101.3.1.2
Mask for the aggregrate
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpBgpAggregateAsSetGenerate		1.3.6.1.4.1.2272.1.8.101.3.1.3
Enable Generates autonomous system set path information.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpBgpAggregateSummaryOnly		1.3.6.1.4.1.2272.1.8.101.3.1.4
Filters all more specific routes from updates.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpBgpAggregateSuppressPolicy		1.3.6.1.4.1.2272.1.8.101.3.1.5
Name of route policy used to select the routes to be suppressed.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..64)

rcIpBgpAggregateAdvertisePolicy		1.3.6.1.4.1.2272.1.8.101.3.1.6
Name of route policy used to select the routes to create AS-SET origin communities.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..64)

rcIpBgpAggregateAttributePolicy		1.3.6.1.4.1.2272.1.8.101.3.1.7
Name of route policy used to set the attribute of the aggregate route.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..64)

rcIpBgpAggregateRowStatus		1.3.6.1.4.1.2272.1.8.101.3.1.8
Row status for create/delete.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpBgpConfederationGroup		1.3.6.1.4.1.2272.1.8.101.4
OBJECT IDENTIFIER

rcIpBgpConfederationIdentifier		1.3.6.1.4.1.2272.1.8.101.4.1
Confederation AS identifier
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

rcIpBgpConfederationPeers		1.3.6.1.4.1.2272.1.8.101.4.2
The string represents ConfederatoinPeers as . Maximum size 255,if any, will not be recorded by this object. The length is a 1-octet field containing the numbner of peers in the value field. The value field contains one or more peers (AS numbers which are part of the confederation). Each AS is represented in the octet string as a pair of octets according to the following algorithm: first-byte-of-pair = ASNumber / 256; second-byte-of-pair = ASNumber & 255;
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..255)

rcIpBgpRouteReflectorGroup		1.3.6.1.4.1.2272.1.8.101.5
OBJECT IDENTIFIER

rcIpBgpRouteReflectionEnable		1.3.6.1.4.1.2272.1.8.101.5.1
Enable Route Reflection on this router
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpBgpRouteReflectorClusterId		1.3.6.1.4.1.2272.1.8.101.5.2
Cluster ID of this router acting as a route reflector
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcIpBgpRouteReflectorClientToClientReflection		1.3.6.1.4.1.2272.1.8.101.5.3
When this router is configured as a route reflector, and the clients are fully meshed, a Disable value disables reflection of routes from one client to another.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpBgpRouteReflectionOperState		1.3.6.1.4.1.2272.1.8.101.5.4
Displays the current route reflection operational state
Status: current	Access: read-only
OBJECT-TYPE
	EnableValue

rcIpBgpNetworkTableSize		1.3.6.1.4.1.2272.1.8.101.6
Network Prefix table size
Status: deprecated	Access: read-only
OBJECT-TYPE
	Integer32

rcIpBgpNetworkTable		1.3.6.1.4.1.2272.1.8.101.7
The networks in this table are either static/directly connected or learned routes. Bgp advertises these network provided they are reachable and are in the IP routing table
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpBgpNetworkEntry

rcIpBgpNetworkEntry		1.3.6.1.4.1.2272.1.8.101.7.1
An entry In NetworkTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpBgpNetworkEntry

rcIpBgpNetworkAddr		1.3.6.1.4.1.2272.1.8.101.7.1.1
Network prefix that BGP will advertise.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcIpBgpNetworkMask		1.3.6.1.4.1.2272.1.8.101.7.1.2
Network mask
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpBgpNetworkRowStatus		1.3.6.1.4.1.2272.1.8.101.7.1.3
Row status for create/delete.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpBgpNetworkMetric		1.3.6.1.4.1.2272.1.8.101.7.1.4
Value of the metric to be used while sending an update for the routes from the network table. Indicates to set the MED value for the routes advertised to ebgp peers.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

rcIpBgpPeerTableSize		1.3.6.1.4.1.2272.1.8.101.8
BGP peer table size
Status: deprecated	Access: read-only
OBJECT-TYPE
	Integer32

rcIpBgpPeerTable		1.3.6.1.4.1.2272.1.8.101.9
IP BGP Peer table
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpBgpPeerEntry

rcIpBgpPeerEntry		1.3.6.1.4.1.2272.1.8.101.9.1
An entry of Ip rcIpBgp Peer Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpBgpPeerEntry

rcIpBgpPeerEnable		1.3.6.1.4.1.2272.1.8.101.9.1.1
Enable/Disable: controls whether the peer connection is enabled or disabled
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

rcIpBgpPeerIpAddress		1.3.6.1.4.1.2272.1.8.101.9.1.2
The Ip address of this peer
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpBgpPeerRemoteAs		1.3.6.1.4.1.2272.1.8.101.9.1.3
Remote Autonomous system number of this peer
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

rcIpBgpPeerGroupName		1.3.6.1.4.1.2272.1.8.101.9.1.4
Peer group name to which this peer belongs (optional)
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

rcIpBgpPeerDefaultOriginate		1.3.6.1.4.1.2272.1.8.101.9.1.5
To allow a BGP speaker (the local router) to send the default route 0.0.0.0 to a neighbor for use as a default route
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpBgpPeerEbgpMultiHop		1.3.6.1.4.1.2272.1.8.101.9.1.6
To accept and attempt BGP connections to external peers residing on networks that are not directly connected
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpBgpPeerAdvertisementInterval		1.3.6.1.4.1.2272.1.8.101.9.1.7
To set the minimum interval between the sending of BGP routing updates Time in seconds. Integer from 5 to 120.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	5..120

rcIpBgpPeerPassword		1.3.6.1.4.1.2272.1.8.101.9.1.8
To enable MD5 authentication on a TCP connection between two BGP peers Case-sensitive password of up to 80 character
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..80)

rcIpBgpPeerWeight		1.3.6.1.4.1.2272.1.8.101.9.1.9
To assign an absolute weight to a BGP network. It can be an integer from 0 to 65535.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

rcIpBgpPeerMaxPrefix		1.3.6.1.4.1.2272.1.8.101.9.1.10
Sets a limit on the number of routes that will be accepted from a neighbor. A value of zero indicates no limit
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..2147483647

rcIpBgpPeerNextHopSelf		1.3.6.1.4.1.2272.1.8.101.9.1.11
Set NextHop Attribute to local router address before sending updates to remote peer
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpBgpPeerRoutePolicyIn		1.3.6.1.4.1.2272.1.8.101.9.1.12
Route Policy Name that will be applied to all networks learned from this peer
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..64)

rcIpBgpPeerRoutePolicyOut		1.3.6.1.4.1.2272.1.8.101.9.1.13
Route policy name that will be applied to all outgoing updates
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..64)

rcIpBgpPeerRouteReflectorClient		1.3.6.1.4.1.2272.1.8.101.9.1.14
Indicates whether this peer is a route reflector client.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpBgpPeerSoftReconfigurationIn		1.3.6.1.4.1.2272.1.8.101.9.1.15
If Peer soft reconfiguration is enabled in the in-bound direction, policy can be changed and routes can re-learned without having to reset the bgp connection. Enabling soft reconfig-in causes all bgp routes to be stored in local memory (even non-best routes)
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpBgpPeerSoftReconfiguration		1.3.6.1.4.1.2272.1.8.101.9.1.16
If rcIpBgpPeerSoftReconfigurationIn is enabled in the in-bound direction, policy can be changed and routes can re-learned without having to reset the bgp connection by setting rcIpBgpPeerSoftReconfiguration to in(1). Setting the value to out (2) forces the neighbor to send out all the updates to the remote neighbor without resetting the connection.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	in(1), out(2), none(3)

rcIpBgpPeerRemovePrivateAs		1.3.6.1.4.1.2272.1.8.101.9.1.17
Enable and disable private AS number from being stripped when sending an update
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpBgpPeerRowStatus		1.3.6.1.4.1.2272.1.8.101.9.1.18
Used to create/delete entries in the Table.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpBgpPeerMD5Authentication		1.3.6.1.4.1.2272.1.8.101.9.1.19
Enable and Disable MD5 authentication
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpBgpPeerDebugMask		1.3.6.1.4.1.2272.1.8.101.9.1.20
value is one of multiple (logically by 'OR' of following value: none (0), error(1), packet(2), event(4), trace(8), warning(16), state(32), init(64), filter(128), update(256), all(511) all(511): Enables all debugging messages. none(0): Disables all debugging messages. error(1): Enables disolay of debug error messages. packet(2): Enables display of debug packet messages. event(4): Enables display of debug event messages. trace(8): Enables display debug trace messages. warning(16): Enables display debug warning messages. state(32): Enables display of debug state transtion messages. init(64): Enables display of debug initialization messages. filter(128): Enables display of debug messages related to filtering. update(256): Enables display of debug messages related to sending and receiving updates.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..511

rcIpBgpPeerSendCommunity		1.3.6.1.4.1.2272.1.8.101.9.1.21
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpBgpPeerUpdateSourceInterface		1.3.6.1.4.1.2272.1.8.101.9.1.22
The IP address to be used for Circuitless IP.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcIpBgpPeerState		1.3.6.1.4.1.2272.1.8.101.9.1.25
The BGP peer connection state.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	idle(1), connect(2), active(3), opensent(4), openconfirm(5), established(6)

rcIpBgpPeerLastError		1.3.6.1.4.1.2272.1.8.101.9.1.26
The last error code and subcode seen by this peer on this connection. If no error has occurred, this field is zero. Otherwise, the first byte of this two byte OCTET STRING contains the error code, and the second byte contains the subcode.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(2)

rcIpBgpPeerVpnv4Address		1.3.6.1.4.1.2272.1.8.101.9.1.27
The vpnv4 routes specified.
Status: current	Access: read-create
OBJECT-TYPE
	EnableValue

rcIpBgpPeerIpvpnLiteCap		1.3.6.1.4.1.2272.1.8.101.9.1.28
The IPVPN-lite capability can be enabled or disabled on the bgp neighbor peer.
Status: current	Access: read-create
OBJECT-TYPE
	EnableValue

rcIpBgpPeerSooAddress		1.3.6.1.4.1.2272.1.8.101.9.1.29
The site-of-origin ip address.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

rcIpBgpPeerSooAsNumber		1.3.6.1.4.1.2272.1.8.101.9.1.30
The asnum for the site-of-origin for bgp peer.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..65535

rcIpBgpPeerSooAssignedNum		1.3.6.1.4.1.2272.1.8.101.9.1.31
The Assigned number required along with asnum or address to configure the site-of-origin for bgp peer.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..2147483647

rcIpBgpPeerSooType		1.3.6.1.4.1.2272.1.8.101.9.1.32
The soo type can be asnum or ipaddress.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(0), asnum(1), ipaddr(2)

rcIpBgpPeerRouteRefresh		1.3.6.1.4.1.2272.1.8.101.9.1.33
Route refresh for bgp peer.
Status: current	Access: read-create
OBJECT-TYPE
	EnableValue

rcIpBgpPeerAsOverride		1.3.6.1.4.1.2272.1.8.101.9.1.34
The AS Override value can be enabled or disabled for bgp peer.
Status: current	Access: read-create
OBJECT-TYPE
	EnableValue

rcIpBgpPeerAllowAsIn		1.3.6.1.4.1.2272.1.8.101.9.1.35
The number of as-in allowed for bgp peer
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..10

rcIpBgpPeerBfdEnable		1.3.6.1.4.1.2272.1.8.101.9.1.36
BFD Admin state flag.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpBgpPeerGroupTableSize		1.3.6.1.4.1.2272.1.8.101.10
BGP Peer Group table size
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpBgpPeerGroupTable		1.3.6.1.4.1.2272.1.8.101.11
IP rcIpBgp Peer Group table. This table contains rows which are template configuration parameters which are shared by a group of peers. Peers belonging to the same group will refer to the same row in this table using a peer group name
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpBgpPeerGroupEntry

rcIpBgpPeerGroupEntry		1.3.6.1.4.1.2272.1.8.101.11.1
An entry of Ip rcIpBgp Peer Group Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpBgpPeerGroupEntry

rcIpBgpPeerGroupEnable		1.3.6.1.4.1.2272.1.8.101.11.1.1
Allows disabling a group of peers
Status: current	Access: read-create
OBJECT-TYPE
	EnableValue

rcIpBgpPeerGroupIndex		1.3.6.1.4.1.2272.1.8.101.11.1.2
Index in to the Peer Group Table
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..1024

rcIpBgpPeerGroupGroupName		1.3.6.1.4.1.2272.1.8.101.11.1.3
Name of the BGP peer group to which this neighbor belong
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..255)

rcIpBgpPeerGroupRemoteAs		1.3.6.1.4.1.2272.1.8.101.11.1.4
Remote Autonomous system number of this peer group (optional)
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..65535

rcIpBgpPeerGroupDefaultOriginate		1.3.6.1.4.1.2272.1.8.101.11.1.5
Enabling this attribute allows a BGP speaker (the local router) to send the default route 0.0.0.0 to the group of neighbors for use as a default route.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

rcIpBgpPeerGroupEbgpMultiHop		1.3.6.1.4.1.2272.1.8.101.11.1.6
To accept and attempt BGP connections to external peers residing on networks that are not directly connected
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

rcIpBgpPeerGroupAdvertisementInterval		1.3.6.1.4.1.2272.1.8.101.11.1.7
To set the minimum interval between the sending of BGP routing updates Time in seconds. Integer from 1 to 120.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..120

rcIpBgpPeerGroupKeepAlive		1.3.6.1.4.1.2272.1.8.101.11.1.8
To set the time interval in seconds between the sending of BGP keep alive messages to remote peers.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..21845

rcIpBgpPeerGroupHoldTime		1.3.6.1.4.1.2272.1.8.101.11.1.9
To configure the hold time for the group of peers in seconds. Usually set to three times the value of the Keepalive time
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	3..65535

rcIpBgpPeerGroupWeight		1.3.6.1.4.1.2272.1.8.101.11.1.10
To assign an absolute weight to a BGP network. Absolute weight, or importance. It can be an integer from 0 to 65535.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..65535

rcIpBgpPeerGroupMaxPrefix		1.3.6.1.4.1.2272.1.8.101.11.1.11
Sets a limit on the number of routes that will be accepted from this group of neighbors. A value of zero indicates no limit
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..2147483647

rcIpBgpPeerGroupNextHopSelf		1.3.6.1.4.1.2272.1.8.101.11.1.12
Set NextHop Attribute to local router address before sending updates to remote peers
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcIpBgpPeerGroupRoutePolicyIn		1.3.6.1.4.1.2272.1.8.101.11.1.13
Route Policy Name that will be applied to all networks learned from this group of peers
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..64)

rcIpBgpPeerGroupRoutePolicyOut		1.3.6.1.4.1.2272.1.8.101.11.1.14
Route policy name that will be applied to all outgoing updates to this group of peers
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..64)

rcIpBgpPeerGroupRouteReflectorClient		1.3.6.1.4.1.2272.1.8.101.11.1.15
Indicates whether this group of peers is a route reflector client.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcIpBgpPeerGroupSoftReconfigurationIn		1.3.6.1.4.1.2272.1.8.101.11.1.16
If Peer soft reconfiguration is enabled in the in bound direction, policy can be changed and routes can re-learned without having to reset the bgp connection. Enabling soft reconfig-in causes all bgp routes to be stored in local memory (even non-best routes)
Status: current	Access: read-create
OBJECT-TYPE
	EnableValue

rcIpBgpPeerGroupSoftReconfiguration		1.3.6.1.4.1.2272.1.8.101.11.1.17
If Peer soft reconfiguration-in is enabled in the in bound direction, policy can be changed and routes can re-learned without having to reset the bgp connection by setting rcIpBgpPeerGroupSoftReconfiguration to in(1). Setting the value to out (2) forces the neighbor to send out all the updates to the remote neighbor without resetting the connection.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	in(1), out(2)

rcIpBgpPeerGroupPassword		1.3.6.1.4.1.2272.1.8.101.11.1.18
To enable MD5 authentication on TCP connections between this local speaker and this group of BGP peers. Case-sensitive password of up to 80 character
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..80)

rcIpBgpPeerGroupRemovePrivateAs		1.3.6.1.4.1.2272.1.8.101.11.1.19
Enable and disable private AS number from being stripped when sending an update
Status: current	Access: read-create
OBJECT-TYPE
	EnableValue

rcIpBgpPeerGroupRowStatus		1.3.6.1.4.1.2272.1.8.101.11.1.20
row status
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcIpBgpPeerGroupMD5Authentication		1.3.6.1.4.1.2272.1.8.101.11.1.21
Enable and Disable MD5 authentication
Status: current	Access: read-create
OBJECT-TYPE
	EnableValue

rcIpBgpPeerGroupSendCommunity		1.3.6.1.4.1.2272.1.8.101.11.1.22
Enables or disables sending the update message community attribute to the specified peer.
Status: current	Access: read-create
OBJECT-TYPE
	EnableValue

rcIpBgpPeerGroupUpdateSourceInterface		1.3.6.1.4.1.2272.1.8.101.11.1.23
The IP address to used for circuitless IP for this peer group.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

rcIpBgpPeerGroupVpnv4Address		1.3.6.1.4.1.2272.1.8.101.11.1.24
The vpnv4 routes specified.
Status: current	Access: read-create
OBJECT-TYPE
	EnableValue

rcIpBgpPeerGroupIpvpnLiteCap		1.3.6.1.4.1.2272.1.8.101.11.1.25
The IPVPN-lite capability can be enabled or disabled on the bgp neighbor peer group.
Status: current	Access: read-create
OBJECT-TYPE
	EnableValue

rcIpBgpPeerGroupSooAddress		1.3.6.1.4.1.2272.1.8.101.11.1.26
The site-of-origin ipaddress.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

rcIpBgpPeerGroupSooAsNumber		1.3.6.1.4.1.2272.1.8.101.11.1.27
The asnum for site-of-origin for bgp peer group.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..65535

rcIpBgpPeerGroupSooAssignedNum		1.3.6.1.4.1.2272.1.8.101.11.1.28
The Assigned number required along with asnum or address to configure the site-of-origin for bgp peer group.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..2147483647

rcIpBgpPeerGroupSooType		1.3.6.1.4.1.2272.1.8.101.11.1.29
The soo type can be asnum or ipaddress.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(0), asnum(1), ipaddr(2)

rcIpBgpPeerGroupRouteRefresh		1.3.6.1.4.1.2272.1.8.101.11.1.30
Route refresh for bgp peer group.
Status: current	Access: read-create
OBJECT-TYPE
	EnableValue

rcIpBgpPeerGroupAsOverride		1.3.6.1.4.1.2272.1.8.101.11.1.31
The AS Override value can be enabled or disabled for bgp peer group.
Status: current	Access: read-create
OBJECT-TYPE
	EnableValue

rcIpBgpPeerGroupAllowAsIn		1.3.6.1.4.1.2272.1.8.101.11.1.32
The number of as-in allowed for bgp peer group.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..10

rcIpBgpPeerGroupDefaultOriginateIpv6		1.3.6.1.4.1.2272.1.8.101.11.1.33
Enabling this attribute allows a BGP speaker (the local router) to send the default route to the group of neighbors for use as a default route.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcIpBgpPeerGroupAfUpdateSourceInterfaceType		1.3.6.1.4.1.2272.1.8.101.11.1.34
The Inet address type used for circuitless IP for this peer group.
Status: current	Access: read-create
OBJECT-TYPE
	InetAddressType

rcIpBgpPeerGroupAfUpdateSourceInterface		1.3.6.1.4.1.2272.1.8.101.11.1.35
The Inet address to used for circuitless IP for this peer group.
Status: current	Access: read-create
OBJECT-TYPE
	InetAddress

rcIpBgpPeerGroupIpv6Cap		1.3.6.1.4.1.2272.1.8.101.11.1.36
The ipv6 capability can be enabled or disabled on the bgp neighbor peer group.
Status: current	Access: read-create
OBJECT-TYPE
	EnableValue

rcIpBgpPeerGroupIpv6RoutePolicyIn		1.3.6.1.4.1.2272.1.8.101.11.1.37
Ipv6 Route Policy Name that will be applied to all networks learned from this group of peers
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..64)

rcIpBgpPeerGroupIpv6RoutePolicyOut		1.3.6.1.4.1.2272.1.8.101.11.1.38
Ipv6 Route policy name that will be applied to all outgoing updates to this group of peers
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..64)

rcIpBgpPeerGroupBfdEnable		1.3.6.1.4.1.2272.1.8.101.11.1.39
Bfd can be enabled or disabled for bgp peer group.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcIpBgpRcvdDampenedPathAttrTableSize		1.3.6.1.4.1.2272.1.8.101.12
table size
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpBgpRcvdDampenedPathAttrTable		1.3.6.1.4.1.2272.1.8.101.13
This table contains info about paths to destination networks received from all BGP-4 peers
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpBgpDampenedPathAttrEntry

rcIpBgpDampenedPathAttrEntry		1.3.6.1.4.1.2272.1.8.101.13.1
Information about a path to a networks
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpBgpDampenedPathAttrEntry

rcIpBgpPathAttrPeer		1.3.6.1.4.1.2272.1.8.101.13.1.1
The IP address of the peer where the path info was learned
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpBgpPathAttrIpAddrPrefixLen		1.3.6.1.4.1.2272.1.8.101.13.1.2
Length in bits of the IP address prefix in the network Layer Reachablity Information field.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..32

rcIpBgpPathAttrIpAddrPrefix		1.3.6.1.4.1.2272.1.8.101.13.1.3
An Ip address prefix in the NLRI Information field. This object is an IP address containing the prefix with length specified by rcIpBgpPathAttrIpAddrPrefixLen are zeroed.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpBgpPathAttrFlapPenalty		1.3.6.1.4.1.2272.1.8.101.13.1.4
Penalty value based on number of route flaps
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpBgpPathAttrFlapCount		1.3.6.1.4.1.2272.1.8.101.13.1.5
Number of times a route flapped since the last time the penalty was reset to zero
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpBgpPathAttrRouteDampened		1.3.6.1.4.1.2272.1.8.101.13.1.6
Shows whether this route is currently suppressed from being announced
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	announced(1), suppressed(2)

rcIpBgpPathAttrReuseTime		1.3.6.1.4.1.2272.1.8.101.13.1.7
Re use time is the system configured time for route reuse
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpBgpPathAttrReuseTimeRemain		1.3.6.1.4.1.2272.1.8.101.13.1.8
Re use time Remain is the number of seconds before the route will be reused
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpBgp4PathAttrTableSize		1.3.6.1.4.1.2272.1.8.101.14
table size
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpBgp4PathAttrTable		1.3.6.1.4.1.2272.1.8.101.15
This table contains info about paths to destination networks received from all BGP-4 peers
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpBgp4PathAttrEntry

rcIpBgp4PathAttrEntry		1.3.6.1.4.1.2272.1.8.101.15.1
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpBgp4PathAttrEntry

rcIpBgp4PathAttrPeer		1.3.6.1.4.1.2272.1.8.101.15.1.1
The IP address of the peer where the path info was learned
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpBgp4PathAttrIpAddrPrefixLen		1.3.6.1.4.1.2272.1.8.101.15.1.2
Length in bits of the IP address prefix in the network Layer Reachablity Information field.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..32

rcIpBgp4PathAttrIpAddrPrefix		1.3.6.1.4.1.2272.1.8.101.15.1.3
An Ip address prefix in the NLRI Information field. This object is an IP address containing the prefix with length specified by rcIpBgpPathAttrIpAddrPrefixLen are zeroed.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpBgp4PathAttrCommunities		1.3.6.1.4.1.2272.1.8.101.15.1.4
The string represents community path attributes as The length is a 1-octet field containing the numbner of community numbers in the value field.The value field contains one or more Community numbers,each community is represented in the octet string as 4 octets.The community numbers in the string beyond maximum size 255,if any, will not be recorded by this object.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(255)

rcIpBgp4PathAttrOriginateId		1.3.6.1.4.1.2272.1.8.101.15.1.5
The IP address of the route who originates the routes
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpBgp4PathAttrClusterId		1.3.6.1.4.1.2272.1.8.101.15.1.6
The string represents Cluster Id path attributes as The length is a 1-octet field containing the number of Cluster Id numbers in the value field.The value field contains one or more Cluster Id numbers,each Cluster Id is represented in the octet string as 4 octets,each four octets is the IpAddress of the router acting as a route reflector.The Cluster Id numbers in the string beyond maximum size 255,if any, will not be recorded by this object.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(255)

rcIpBgpExt		1.3.6.1.4.1.2272.1.8.101.16
OBJECT IDENTIFIER

rcIpBgpExtAggregateAfTableSize		1.3.6.1.4.1.2272.1.8.101.16.1
Size of address family independent bgp aggregate table
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcIpBgpExtAggregateAfTable		1.3.6.1.4.1.2272.1.8.101.16.2
Replaces rcIpBgpAggregateTable. To specify the list of ipv4 and ipv6 aggregate prefixes to be created by the BGP routing process and the options to be used while aggregating.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpBgpExtAggregateAfEntry

rcIpBgpExtAggregateAfEntry		1.3.6.1.4.1.2272.1.8.101.16.2.1
An entry of v4/v6 aggregate prefix to be created by BGP routing process and the options to be used while aggregating.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpBgpExtAggregateAfEntry

rcIpBgpExtAggregateAfAddressType		1.3.6.1.4.1.2272.1.8.101.16.2.1.1
Inet Address Type of aggregate address.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddressType

rcIpBgpExtAggregateAfAddress		1.3.6.1.4.1.2272.1.8.101.16.2.1.2
V4 or V6 Prefix to create an aggregate address in BGP routing table.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddress

rcIpBgpExtAggregateAfPrefixLen		1.3.6.1.4.1.2272.1.8.101.16.2.1.3
Prefix length of the aggregate inet address
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddressPrefixLength

rcIpBgpExtAggregateAfAsSetGenerate		1.3.6.1.4.1.2272.1.8.101.16.2.1.4
Enable Generates autonomous system set path information.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcIpBgpExtAggregateAfSummaryOnly		1.3.6.1.4.1.2272.1.8.101.16.2.1.5
Filters all more specific routes from updates.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcIpBgpExtAggregateAfSuppressPolicy		1.3.6.1.4.1.2272.1.8.101.16.2.1.6
Name of route policy used to select the routes to be suppressed.
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString	Size(0..64)

rcIpBgpExtAggregateAfAdvertisePolicy		1.3.6.1.4.1.2272.1.8.101.16.2.1.7
Name of route policy used to select the routes to create AS-SET origin communities.
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString	Size(0..64)

rcIpBgpExtAggregateAfAttributePolicy		1.3.6.1.4.1.2272.1.8.101.16.2.1.8
Name of route policy used to set the attribute of the aggregate route.
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString	Size(0..64)

rcIpBgpExtAggregateAfRowStatus		1.3.6.1.4.1.2272.1.8.101.16.2.1.9
Row status for create/delete.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcIpBgpExtNetworkAfTableSize		1.3.6.1.4.1.2272.1.8.101.16.3
Address family independent bgp Network Prefix table size
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcIpBgpExtNetworkAfTable		1.3.6.1.4.1.2272.1.8.101.16.4
This table replaces rcIpBgpNetworkTable. This table supports V4 and V6 BGP networks. The networks in this table are either static/directly connected or learned routes. Bgp advertises these network provided they are reachable and are in the IP routing table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpBgpExtNetworkAfEntry

rcIpBgpExtNetworkAfEntry		1.3.6.1.4.1.2272.1.8.101.16.4.1
An entry in bgp NetworkTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpBgpExtNetworkAfEntry

rcIpBgpExtNetworkAfAddrType		1.3.6.1.4.1.2272.1.8.101.16.4.1.1
Inet address type of the Network prefix that BGP will advertise.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddressType

rcIpBgpExtNetworkAfAddr		1.3.6.1.4.1.2272.1.8.101.16.4.1.2
v4/v6 Network prefix that BGP will advertise.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddress

rcIpBgpExtNetworkAfPrefixLen		1.3.6.1.4.1.2272.1.8.101.16.4.1.3
Prefix length of the v4/v6 bgp network address
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddressPrefixLength

rcIpBgpExtNetworkAfMetric		1.3.6.1.4.1.2272.1.8.101.16.4.1.4
Value of the metric to be used while sending an update for the routes from the network table. Indicates to set the MED value for the routes advertised to ebgp Peers.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..65535

rcIpBgpExtNetworkAfRowStatus		1.3.6.1.4.1.2272.1.8.101.16.4.1.5
Row status for create/delete.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcIpBgpExtPeerAfTableSize		1.3.6.1.4.1.2272.1.8.101.16.5
Size of Address family independent BGP Peer Table
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcIpBgpExtPeerAfTable		1.3.6.1.4.1.2272.1.8.101.16.6
Extension to the BGP peer table. This table contains, one entry per BGP peer, information about the connections with BGP Peers, which is not supported by the standard MIB draft. This table replaces rcIpBgpPeerTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpBgpExtPeerAfEntry

rcIpBgpExtPeerAfEntry		1.3.6.1.4.1.2272.1.8.101.16.6.1
Entry containing miscelleneous information (info not present in the standard BGP peer table) about the connection with a remote BGP peer .
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpBgpExtPeerAfEntry

rcIpBgpExtPeerAfGroupName		1.3.6.1.4.1.2272.1.8.101.16.6.1.1
Peer group name to which this peer belongs (optional)
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString	Size(0..255)

rcIpBgpExtPeerAfDefaultOriginate		1.3.6.1.4.1.2272.1.8.101.16.6.1.2
To allow a BGP speaker (the local router) to send the default route 0.0.0.0 to a neighbor for use as a default route
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcIpBgpExtPeerAfDefaultOriginateIpv6		1.3.6.1.4.1.2272.1.8.101.16.6.1.3
To allow a BGP speaker (the local router) to Send the default ipv6 route to a neighbor for use as a default route
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcIpBgpExtPeerAfEbgpMultiHop		1.3.6.1.4.1.2272.1.8.101.16.6.1.4
To accept and attempt BGP connections to external peers residing on networks that are not directly connected
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcIpBgpExtPeerAfAdvertisementInterval		1.3.6.1.4.1.2272.1.8.101.16.6.1.5
To set the minimum interval between the sending Of BGP routing updates Time in seconds. Integer from 5 to 120.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	5..120

rcIpBgpExtPeerAfPassword		1.3.6.1.4.1.2272.1.8.101.16.6.1.6
To enable MD5 authentication on a TCP connection between two BGP Peers Case-sensitive password of up to 80 character
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString	Size(0..80)

rcIpBgpExtPeerAfWeight		1.3.6.1.4.1.2272.1.8.101.16.6.1.7
To assign an absolute weight to a BGP network. It can be an integer from 0 to 65535.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..65535

rcIpBgpExtPeerAfMaxPrefix		1.3.6.1.4.1.2272.1.8.101.16.6.1.8
Sets a limit on the number of routes that will be accepted from a neighbor. A value of zero indicates no limit
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..2147483647

rcIpBgpExtPeerAfNextHopSelf		1.3.6.1.4.1.2272.1.8.101.16.6.1.9
Set NextHop Attribute to local router address Before sending updates to remote peer
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcIpBgpExtPeerAfRoutePolicyIn		1.3.6.1.4.1.2272.1.8.101.16.6.1.10
Route Policy Name that will be applied to all Networks learned from this peer
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString	Size(0..64)

rcIpBgpExtPeerAfRoutePolicyOut		1.3.6.1.4.1.2272.1.8.101.16.6.1.11
Route policy name that will be applied to all outgoing updates
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString	Size(0..64)

rcIpBgpExtPeerAfRouteReflectorClient		1.3.6.1.4.1.2272.1.8.101.16.6.1.12
Indicates whether this peer is a route reflector client.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcIpBgpExtPeerAfSoftReconfigurationIn		1.3.6.1.4.1.2272.1.8.101.16.6.1.13
If Peer soft reconfiguration is enabled in the in-bound direction, policy can be changed and routes can re-learned without having to reset the bgp connection. Enabling soft reconfig-in causes all bgp routes to be stored in local memory (even non-best routes)
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcIpBgpExtPeerAfSoftReconfiguration		1.3.6.1.4.1.2272.1.8.101.16.6.1.14
If rcIpBgpExtPeerAfSoftReconfigurationIn is enabled in the in-bound direction, policy can be changed and routes can re-learned without having to reset the bgp connection by setting rcIpBgpExtPeerAfSoftReconfiguration to in(1). Setting the value to out (2) forces the neighbor to send out all the updates to the remote neighbor without resetting the connection.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	in(1), out(2), none(3)

rcIpBgpExtPeerAfRemovePrivateAs		1.3.6.1.4.1.2272.1.8.101.16.6.1.15
Enable and disable private AS number from being stripped when sending an update
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcIpBgpExtPeerAfMD5Authentication		1.3.6.1.4.1.2272.1.8.101.16.6.1.16
Enable and Disable MD5 authentication
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcIpBgpExtPeerAfDebugMask		1.3.6.1.4.1.2272.1.8.101.16.6.1.17
value is one of multiple (logically by 'OR' of following value: none (0), error(1), packet(2), event(4), trace(8), warning(16), state(32), init(64), filter(128), update(256), all(511) all(511): Enables all debugging messages. none(0): Disables all debugging messages. error(1): Enables display of debug error messages. packet(2): Enables display of debug packet messages. event(4): Enables display of debug event messages. trace(8): Enables display debug trace messages. warning(16): Enables display debug warning messages. state(32): Enables display of debug state transition messages. init(64): Enables display of debug initialization messages. filter(128): Enables display of debug messages related to filtering. update(256): Enables display of debug messages related to sending and receiving updates.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..511

rcIpBgpExtPeerAfSendCommunity		1.3.6.1.4.1.2272.1.8.101.16.6.1.18
Enables or disables sending the update message community attribute to the specified peer.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcIpBgpExtPeerAfUpdateSourceInterface		1.3.6.1.4.1.2272.1.8.101.16.6.1.19
The Inet address to be used for Circuitless IP.
Status: current	Access: read-create
OBJECT-TYPE
	InetAddress

rcIpBgpExtPeerAfVpnv4Address		1.3.6.1.4.1.2272.1.8.101.16.6.1.20
The vpnv4 routes specified.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcIpBgpExtPeerAfIpv6Cap		1.3.6.1.4.1.2272.1.8.101.16.6.1.21
The ipv6 capability can be enabled or disabled on the bgp neighbor peer.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcIpBgpExtPeerAfIpvpnLiteCap		1.3.6.1.4.1.2272.1.8.101.16.6.1.22
The IPVPN-lite capability can be enabled or disabled on the bgp neighbor peer.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcIpBgpExtPeerAfSooAddress		1.3.6.1.4.1.2272.1.8.101.16.6.1.23
The site-of-origin ip address.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

rcIpBgpExtPeerAfSooAsNumber		1.3.6.1.4.1.2272.1.8.101.16.6.1.24
The asnum for the site-of-origin for bgp peer.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..65535

rcIpBgpExtPeerAfSooAssignedNum		1.3.6.1.4.1.2272.1.8.101.16.6.1.25
The Assigned number required along with asnum or address to configure the site-of-origin for bgp peer.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..2147483647

rcIpBgpExtPeerAfSooType		1.3.6.1.4.1.2272.1.8.101.16.6.1.26
The soo type can be asnum or ipaddress.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(0), asnum(1), ipaddr(2)

rcIpBgpExtPeerAfRouteRefresh		1.3.6.1.4.1.2272.1.8.101.16.6.1.27
Route refresh for bgp peer.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcIpBgpExtPeerAfAsOverride		1.3.6.1.4.1.2272.1.8.101.16.6.1.28
The AS Override value can be enabled or disabled for bgp peer.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcIpBgpExtPeerAfAllowAsIn		1.3.6.1.4.1.2272.1.8.101.16.6.1.29
The number of as-in allowed for bgp peer.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..10

rcIpBgpExtPeerAfIpv6RoutePolicyIn		1.3.6.1.4.1.2272.1.8.101.16.6.1.30
Ipv6 Route Policy Name that will be applied to all Networks learned from this peer
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString	Size(0..64)

rcIpBgpExtPeerAfIpv6RoutePolicyOut		1.3.6.1.4.1.2272.1.8.101.16.6.1.31
Ipv6 Route policy name that will be applied to all outgoing updates
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString	Size(0..64)

rcIpBgpExtPeerAfEnable		1.3.6.1.4.1.2272.1.8.101.16.6.1.32
Used to enable/disable bgp+ peer
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcIpBgpExtPeerAfRemoteAs		1.3.6.1.4.1.2272.1.8.101.16.6.1.33
Used to manually configure the remote as of the bgp+ peer.
Status: current	Access: read-create
OBJECT-TYPE
	InetAutonomousSystemNumber

rcIpBgpExtPeerAfConnectRetryInterval		1.3.6.1.4.1.2272.1.8.101.16.6.1.34
Used to configure the ConnectRetry timer for the BGP+ peer.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	1..65535

rcIpBgpExtPeerAfHoldTimeConfigured		1.3.6.1.4.1.2272.1.8.101.16.6.1.35
Used to configure the Hold Timer for the BGP+ peer.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0 | 3..65535

rcIpBgpExtPeerAfKeepAliveConfigured		1.3.6.1.4.1.2272.1.8.101.16.6.1.36
Used to configure the KeepAlive Timer for the BGP+ peer.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0 | 1..21845

rcIpBgpExtPeerAfRowStatus		1.3.6.1.4.1.2272.1.8.101.16.6.1.37
Used to create/delete entries in the Table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcIpBgpExtPeerAfNewRemoteAs		1.3.6.1.4.1.2272.1.8.101.16.6.1.38
Remote Autonomous system number of this peer
Status: current	Access: read-create
OBJECT-TYPE
	OCTET STRING	Size(0..4)

rcIpBgpExtPeerAfBfdEnable		1.3.6.1.4.1.2272.1.8.101.16.6.1.39
BFD Admin state flag.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcIpBgpExtAfPathAttrTable		1.3.6.1.4.1.2272.1.8.101.16.7
Extension to rcIpBgpTmpAfPathAttrTable. This table contains info about additional BGP path attributes not covered in rcIpBgpTmpAfPathAttrTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpBgpExtAfPathAttrEntry

rcIpBgpExtAfPathAttrEntry		1.3.6.1.4.1.2272.1.8.101.16.7.1
Each entry contains data about additional path attributes associated with a given prefix in the rcIpBgpTmpNlriTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpBgpExtAfPathAttrEntry

rcIpBgpExtAfPathAttrUnknown		1.3.6.1.4.1.2272.1.8.101.16.7.1.1
Replaces bgp4PathAttrUnknown. One or more path attributes not understood by this BGP4 speaker. Size zero (0) indicates the absence of such attribute(s). Octets beyond the maximum size, if any, are not recorded by this object.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..255)

rcIpBgpExtAfPathAttrCommunities		1.3.6.1.4.1.2272.1.8.101.16.7.1.2
The string represents BGP+ community path attributes as . The length is a 1-octet field containing the numbner of community numbers in the value field.The value field contains one or more Community numbers,each community is represented in the octet string as 4 octets.The community numbers in the string beyond maximum size 255,if any, will not be recorded by this object.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..255)

rcIpBgpExtAfPathAttrOriginateId		1.3.6.1.4.1.2272.1.8.101.16.7.1.3
In a BGP+ context, the IP address of the router which originates the routes.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpBgpExtAfPathAttrClusterId		1.3.6.1.4.1.2272.1.8.101.16.7.1.4
The string represents BGP+ Cluster Id path attributes as . The length is a 1-octet field containing the number of Cluster Id numbers in the value field. The value field contains one or more Cluster Id numbers, each Cluster Id is represented in the octet string as 4 octets, each four octets is the IpAddress of the router acting as a route reflector.The Cluster Id numbers in the string beyond maximum size 255,if any, will not be recorded by this object.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..255)

rcIpBgpTmp		1.3.6.1.4.1.2272.1.8.101.17
OBJECT IDENTIFIER

rcIpBgpTmpLocalAsNew		1.3.6.1.4.1.2272.1.8.101.17.9
The local autonomous system number. This object supports 4 byte ASes and replaces bgpLocalAs.
Status: current	Access: read-only
OBJECT-TYPE
	InetAutonomousSystemNumber

rcIpBgpTmpPeerAf		1.3.6.1.4.1.2272.1.8.101.17.10
OBJECT IDENTIFIER

rcIpBgpTmpPeerAfTable		1.3.6.1.4.1.2272.1.8.101.17.10.1
BGP peer table. This table contains, one entry per BGP peer, information about the connections with BGP peers. This table replaces bgpPeerTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpBgpTmpPeerAfEntry

rcIpBgpTmpPeerAfEntry		1.3.6.1.4.1.2272.1.8.101.17.10.1.1
Entry containing information about the connection with a remote BGP peer.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpBgpTmpPeerAfEntry

rcIpBgpTmpPeerAfInstance		1.3.6.1.4.1.2272.1.8.101.17.10.1.1.1
The routing instance index. Some BGP implementations permit the creation of multiple instances of a BGP routing process. An example includes routers running BGP/MPLS IP Virtual Private Networks. Implementations that do not support multiple routing instances should return 1 for this object.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..4294967295

rcIpBgpTmpPeerAfLocalAddrType		1.3.6.1.4.1.2272.1.8.101.17.10.1.1.2
The address family of the local end of the peering session.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddressType

rcIpBgpTmpPeerAfLocalAddr		1.3.6.1.4.1.2272.1.8.101.17.10.1.1.3
The local IP address of this entry's BGP connection.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddress

rcIpBgpTmpPeerAfRemoteAddrType		1.3.6.1.4.1.2272.1.8.101.17.10.1.1.4
The address family of the remote end of the peering session.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddressType

rcIpBgpTmpPeerAfRemoteAddr		1.3.6.1.4.1.2272.1.8.101.17.10.1.1.5
The remote IP address of this entry's BGP peer.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddress

rcIpBgpTmpPeerAfLocalPort		1.3.6.1.4.1.2272.1.8.101.17.10.1.1.6
The local port for the TCP connection between the BGP peers.
Status: current	Access: read-only
OBJECT-TYPE
	InetPortNumber

rcIpBgpTmpPeerAfLocalAs		1.3.6.1.4.1.2272.1.8.101.17.10.1.1.7
Some implementations of BGP can represent themselves as multiple ASes. This is the AS that this peering session is representing itself as to the remote peer.
Status: current	Access: read-only
OBJECT-TYPE
	InetAutonomousSystemNumber

rcIpBgpTmpPeerAfRemotePort		1.3.6.1.4.1.2272.1.8.101.17.10.1.1.8
The remote port for the TCP connection between the BGP peers. Note that the objects rcIpBgpTmpPeerAfLocalAddr, rcIpBgpTmpPeerAfLocalPort, rcIpBgpTmpPeerAfRemoteAddr and rcIpBgpTmpPeerAfRemotePort provide the appropriate reference to the standard MIB TCP connection table, or even the ipv6 TCP MIB as in RFC 4022.
Status: current	Access: read-only
OBJECT-TYPE
	InetPortNumber

rcIpBgpTmpPeerAfRemoteAs		1.3.6.1.4.1.2272.1.8.101.17.10.1.1.9
The remote autonomous system number received in the BGP OPEN message.
Status: current	Access: read-only
OBJECT-TYPE
	InetAutonomousSystemNumber

rcIpBgpTmpPeerAfIdentifier		1.3.6.1.4.1.2272.1.8.101.17.10.1.1.10
The BGP Identifier of this entry's remote BGP peer. This entry should be 0.0.0.0 unless the rcIpBgpTmpPeerAfPeerState is in the openconfirm or the established state.
Status: current	Access: read-only
OBJECT-TYPE
	RcIpBgpTmpIdentifierTC

rcIpBgpTmpPeerAfAdminStatus		1.3.6.1.4.1.2272.1.8.101.17.10.1.1.11
Whether or not the BGP FSM for this remote peer is halted or running. The BGP FSM for a remote peer is halted after processing a Stop event. Likewise, it is in the running state after a Start event. The rcIpBgpTmpPeerAfState will generally be in the idle state when the FSM is halted, although some extensions such as Graceful Restart will leave the peer in the Idle state but with the FSM running.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	halted(1), running(2)

rcIpBgpTmpPeerAfPeerState		1.3.6.1.4.1.2272.1.8.101.17.10.1.1.12
The BGP peer connection state.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	idle(1), connect(2), active(3), opensent(4), openconfirm(5), established(6)

rcIpBgpTmpPeerAfConfiguredVersion		1.3.6.1.4.1.2272.1.8.101.17.10.1.1.13
The configured version to originally start with this remote peer. The BGP speaker may permit negotiation to a lower version number of the protocol.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	1..255

rcIpBgpTmpPeerAfNegotiatedVersion		1.3.6.1.4.1.2272.1.8.101.17.10.1.1.14
The negotiated version of BGP running between the two peers. This entry MUST be zero (0) unless the rcIpBgpTmpPeerAfState is in the openconfirm or the established state. Note that legal values for this object are between 0 and 255.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	1..255

rcIpBgpTmpPeerAfErrors		1.3.6.1.4.1.2272.1.8.101.17.10.2
OBJECT IDENTIFIER

rcIpBgpTmpPeerAfErrorsTable		1.3.6.1.4.1.2272.1.8.101.17.10.2.1
On a per-peer basis, this table reflects the last protocol-defined error encountered and reported on the peer session. If no entry for a given peer exists in this table, then no such errors have been observed, reported, and recorded on the session.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpBgpTmpPeerAfErrorsEntry

rcIpBgpTmpPeerAfErrorsEntry		1.3.6.1.4.1.2272.1.8.101.17.10.2.1.1
Each entry contains information about errors sent and received for a particular BGP peer.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpBgpTmpPeerAfErrorsEntry

rcIpBgpTmpPeerAfLastErrorCodeReceived		1.3.6.1.4.1.2272.1.8.101.17.10.2.1.1.1
The last error code received from this peer via NOTIFICATION message on this connection. If no error has occurred, this field is zero.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(1)

rcIpBgpTmpPeerAfLastErrorSubCodeReceived		1.3.6.1.4.1.2272.1.8.101.17.10.2.1.1.2
The last subcode received from this peer via NOTIFICATION message on this connection. If no error has occurred, this field is zero.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(1)

rcIpBgpTmpPeerAfLastErrorReceivedTime		1.3.6.1.4.1.2272.1.8.101.17.10.2.1.1.3
The timestamp that the last NOTIFICATION was received from this peer.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

rcIpBgpTmpPeerAfLastErrorReceivedText		1.3.6.1.4.1.2272.1.8.101.17.10.2.1.1.4
This object contains an implementation specific explanation of the error that was reported.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString

rcIpBgpTmpPeerAfLastErrorReceivedData		1.3.6.1.4.1.2272.1.8.101.17.10.2.1.1.5
The last error code's data seen by this peer. Per RFC 2578, some implementations may have limitations dealing with OCTET STRINGS larger than 255. Thus, this data may be truncated.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..4075)

rcIpBgpTmpPeerAfLastErrorCodeSent		1.3.6.1.4.1.2272.1.8.101.17.10.2.1.1.6
The last error code sent to this peer via NOTIFICATION message on this connection. If no error has occurred, this field is zero.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(1)

rcIpBgpTmpPeerAfLastErrorSubCodeSent		1.3.6.1.4.1.2272.1.8.101.17.10.2.1.1.7
The last subcode sent to this peer via NOTIFICATION message on this connection. If no error has occurred, this field is zero.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(1)

rcIpBgpTmpPeerAfLastErrorSentTime		1.3.6.1.4.1.2272.1.8.101.17.10.2.1.1.8
The timestamp that the last NOTIFICATION was sent to this peer.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

rcIpBgpTmpPeerAfLastErrorSentText		1.3.6.1.4.1.2272.1.8.101.17.10.2.1.1.9
This object contains an implementation specific explanation of the error that is being reported.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString

rcIpBgpTmpPeerAfLastErrorSentData		1.3.6.1.4.1.2272.1.8.101.17.10.2.1.1.10
The last error code's data sent to this peer. Per RFC 2578, some implementations may have limitations dealing with OCTET STRINGS larger than 255. Thus, this data may be truncated.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..4075)

rcIpBgpTmpPeerAfTimers		1.3.6.1.4.1.2272.1.8.101.17.10.3
OBJECT IDENTIFIER

rcIpBgpTmpPeerAfEventTimesTable		1.3.6.1.4.1.2272.1.8.101.17.10.3.1
A table reporting the per-peering session amount of time elapsed and update events since the peering session advanced into the established state.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpBgpTmpPeerAfEventTimesEntry

rcIpBgpTmpPeerAfEventTimesEntry		1.3.6.1.4.1.2272.1.8.101.17.10.3.1.1
Each row contains a set of statistics about time spent and events encountered in the peer session established state.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpBgpTmpPeerAfEventTimesEntry

rcIpBgpTmpPeerAfFsmEstablishedTime		1.3.6.1.4.1.2272.1.8.101.17.10.3.1.1.1
This timer indicates how long (in seconds) this peer has been in the established state or how long since this peer was last in the established state. It is set to zero when a new peer is configured or when the router is booted. If the peer has never reached the established state, the value remains zero.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcIpBgpTmpPeerAfInUpdatesElapsedTime		1.3.6.1.4.1.2272.1.8.101.17.10.3.1.1.2
Elapsed time (in seconds) since the last BGP UPDATE message was received from the peer. Each time bgpPeerInUpdates is incremented, the value of this object is set to zero (0).
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcIpBgpTmpPeerAfConfiguredTimersTable		1.3.6.1.4.1.2272.1.8.101.17.10.3.2
Per peer management data on BGP session timers.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpBgpTmpPeerAfConfiguredTimersEntry

rcIpBgpTmpPeerAfConfiguredTimersEntry		1.3.6.1.4.1.2272.1.8.101.17.10.3.2.1
Each entry corresponds to the current state of BGP timers on a given peering session.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpBgpTmpPeerAfConfiguredTimersEntry

rcIpBgpTmpPeerAfConnectRetryInterval		1.3.6.1.4.1.2272.1.8.101.17.10.3.2.1.1
Time interval (in seconds) for the ConnectRetry timer. The suggested value for this timer is 120 seconds.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	1..65535

rcIpBgpTmpPeerAfHoldTimeConfigured		1.3.6.1.4.1.2272.1.8.101.17.10.3.2.1.2
Time interval (in seconds) for the Hold Timer established with the peer. The value of this object is calculated by this BGP speaker, using the smaller of the values in bgpPeerHoldTimeConfigured and the Hold Time received in the OPEN message. This value must be at least three seconds if it is not zero (0). If the Hold Timer has not been established with the peer this object MUST have a value of zero (0). If the bgpPeerHoldTimeConfigured object has a value of (0), then this object MUST have a value of (0).
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0 | 3..65535

rcIpBgpTmpPeerAfKeepAliveConfigured		1.3.6.1.4.1.2272.1.8.101.17.10.3.2.1.3
Time interval (in seconds) for the KeepAlive timer configured for this BGP speaker with this peer. The value of this object will only determine the KEEPALIVE messages' frequency relative to the value specified in bgpPeerHoldTimeConfigured; the actual time interval for the KEEPALIVE messages is indicated by bgpPeerKeepAlive. A reasonable maximum value for this timer would be one third of that of bgpPeerHoldTimeConfigured. If the value of this object is zero (0), no periodic KEEPALIVE messages are sent to the peer after the BGP connection has been established. The suggested value for this timer is 30 seconds.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0 | 1..21845

rcIpBgpTmpPeerAfMinASOrigInterval		1.3.6.1.4.1.2272.1.8.101.17.10.3.2.1.4
Time interval (in seconds) for the MinASOriginationInterval timer. The suggested value for this timer is 15 seconds.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..65535

rcIpBgpTmpPeerAfMinRouteAdverInterval		1.3.6.1.4.1.2272.1.8.101.17.10.3.2.1.5
Time interval (in seconds) for the MinRouteAdvertisementInterval timer. The suggested value for this timer is 30 seconds for EBGP connections and 5 seconds for IBGP connections.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..65535

rcIpBgpTmpPeerAfNegotiatedTimersTable		1.3.6.1.4.1.2272.1.8.101.17.10.3.3
Configured values of per-peer timers are seen in the rcIpBgpTmpPeerAfConfiguredTimersTable. Values in this table reflect the current operational values, after negotiation from values derived from initial configuration.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpBgpTmpPeerAfNegotiatedTimersEntry

rcIpBgpTmpPeerAfNegotiatedTimersEntry		1.3.6.1.4.1.2272.1.8.101.17.10.3.3.1
Each entry reflects a value of the currently operational, negotiated timer as reflected in the rcIpBgpTmpPeerAfNegotiatedTimersEntry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpBgpTmpPeerAfNegotiatedTimersEntry

rcIpBgpTmpPeerAfHoldTime		1.3.6.1.4.1.2272.1.8.101.17.10.3.3.1.1
The value of this object is calculated by this BGP Speaker as being; zero (0) - if this was the value sent by the peer and this value is permitted by this BGP Speaker. In this case, no keepalive messages are sent and the Hold Timer is not set. At least three (3). This value is the smaller of the value sent by this peer in the OPEN message and rcIpBgpTmpPeerAfHoldTimeConfigured for this peer. This value is only defined when the peering session is in the Established state.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0 | 3..65535

rcIpBgpTmpPeerAfKeepAlive		1.3.6.1.4.1.2272.1.8.101.17.10.3.3.1.2
Time interval in seconds for the KeepAlive timer established with the peer. The value of this object is calculated by this BGP speaker such that, when compared with rcIpBgpTmpPeerAfHoldTime, it has the same proportion as what rcIpBgpTmpPeerAfKeepAliveConfigured has when compared with rcIpBgpTmpPeerAfHoldTimeConfigured. If the value of this object is zero (0), it indicates that the KeepAlive timer has not been established with the peer, or, the value of rcIpBgpTmpPeerAfKeepAliveConfigured is zero (0). This value is only defined when the peering session is in the Established state.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0 | 1..21845

rcIpBgpTmpPeerAfCounters		1.3.6.1.4.1.2272.1.8.101.17.10.4
OBJECT IDENTIFIER

rcIpBgpTmpPeerAfCountersTable		1.3.6.1.4.1.2272.1.8.101.17.10.4.1
The counters associated with a BGP Peer.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpBgpTmpPeerAfCountersEntry

rcIpBgpTmpPeerAfCountersEntry		1.3.6.1.4.1.2272.1.8.101.17.10.4.1.1
Each entry contains counters of message transmissions and FSM transitions for a given BGP Peering session.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpBgpTmpPeerAfCountersEntry

rcIpBgpTmpPeerAfInUpdates		1.3.6.1.4.1.2272.1.8.101.17.10.4.1.1.1
The number of BGP UPDATE messages received on this connection.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcIpBgpTmpPeerAfOutUpdates		1.3.6.1.4.1.2272.1.8.101.17.10.4.1.1.2
The number of BGP UPDATE messages transmitted on this connection.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcIpBgpTmpPeerAfInTotalMessages		1.3.6.1.4.1.2272.1.8.101.17.10.4.1.1.3
The total number of messages received from the remote peer on this connection.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcIpBgpTmpPeerAfOutTotalMessages		1.3.6.1.4.1.2272.1.8.101.17.10.4.1.1.4
The total number of messages transmitted to the remote peer on this connection.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcIpBgpTmpPeerAfFsmEstablishedTransitions		1.3.6.1.4.1.2272.1.8.101.17.10.4.1.1.5
The total number of times the BGP FSM transitioned into the established state for this peer.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcIpBgpTmpRib		1.3.6.1.4.1.2272.1.8.101.17.11
OBJECT IDENTIFIER

rcIpBgpTmpNlriTable		1.3.6.1.4.1.2272.1.8.101.17.11.1
The BGP-4 Received Path Attribute Table contains information about paths to destination networks received from all BGP4 peers. Collectively, this represents the Adj-Ribs-In. The route where rcIpBgpTmpNlriBest is true represents, for this NLRI, the route that is installed in the LocRib from the Adj-Ribs-In.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpBgpTmpNlriEntry

rcIpBgpTmpNlriEntry		1.3.6.1.4.1.2272.1.8.101.17.11.1.1
Information about a path to a network.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpBgpTmpNlriEntry

rcIpBgpTmpNlriIndex		1.3.6.1.4.1.2272.1.8.101.17.11.1.1.1
This index allows for multiple instances of a base prefix for a certain AFI-SAFI from a given peer. This is currently useful for two things: 1. Allowing for a peer in future implementations to send more than a single route instance. 2. Allow for extensions which extend the NLRI field to send the same prefix while utilizing other extension specific information. An example of this is RFC 3107 - Carrying MPLS labels in BGP.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

rcIpBgpTmpNlriAfi		1.3.6.1.4.1.2272.1.8.101.17.11.1.1.2
The address family of the prefix for this NLRI. Note that the AFI is not necessarily equivalent to the an InetAddressType.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpBgpTmpAddressFamilyIdentifierTC

rcIpBgpTmpNlriSafi		1.3.6.1.4.1.2272.1.8.101.17.11.1.1.3
The subsequent address family of the prefix for this NLRI
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpBgpTmpSubsequentAddressFamilyIdentifierTC

rcIpBgpTmpNlriPrefixType		1.3.6.1.4.1.2272.1.8.101.17.11.1.1.4
The type of the IP address prefix in the Network Layer Reachability Information field. The value of this object is derived from the appropriate value from the rcIpBgpTmpNlriAfi field. Where an appropriate InetAddressType is not available, the value of the object must be unknown(0).
Status: current	Access: read-only
OBJECT-TYPE
	InetAddressType

rcIpBgpTmpNlriPrefix		1.3.6.1.4.1.2272.1.8.101.17.11.1.1.5
An IP address prefix in the Network Layer Reachability Information field. This object is an IP address containing the prefix with length specified by rcIpBgpTmpAfPathAttrAddrPrefixLen. Any bits beyond the length specified by rcIpBgpTmpAfPathAttrAddrPrefixLen are zeroed.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddress

rcIpBgpTmpNlriPrefixLen		1.3.6.1.4.1.2272.1.8.101.17.11.1.1.6
Length in bits of the address prefix in the Network Layer Reachability Information field.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddressPrefixLength

rcIpBgpTmpNlriBest		1.3.6.1.4.1.2272.1.8.101.17.11.1.1.7
An indication of whether or not this route was chosen as the best BGP4 route for this destination.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcIpBgpTmpNlriCalcLocalPref		1.3.6.1.4.1.2272.1.8.101.17.11.1.1.8
The degree of preference calculated by the receiving BGP4 speaker for an advertised route. In the case where this prefix is ineligible, this object will be absent.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcIpBgpTmpAfPathAttrIndex		1.3.6.1.4.1.2272.1.8.101.17.11.1.1.9
This value is a unique index for entries in the rcIpBgpTmpAfPathAttrTable. It is assigned by the agent at the point of creation of the rcIpBgpTmpAfPathAttrTable row entry. While its value is guaranteed to be unique at any time, it is otherwise opaque to the management application with respect to its value or the contiguity of rcIpBgpTmpAfPathAttrIndex row instance values across rows of the rcIpBgpTmpAfPathAttrTable. Note well that this index is used to distinguish unique sets of Path Attributes sent as part of BGP NLRI. The implementor is thus encouraged to make this index unique per set of all received path attributes. This value may be used to index tables in extension MIBs that share the property of belonging to the same received Path Attribute tuple.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcIpBgpTmpAfPathAttrUnknownIndex		1.3.6.1.4.1.2272.1.8.101.17.11.1.1.10
This value is a unique index for entries in the rcIpBgpTmpAfPathAttrUnknownTable. It is assigned by the agent at the point of creation of the rcIpBgpTmpAfPathAttrUnknownTable row entry. While its value is guaranteed to be unique at any time, it is otherwise opaque to the management application with respect to its value or the contiguity of rcIpBgpTmpAfPathAttrUnknownIndex row instance values across rows of the rcIpBgpTmpAfPathAttrUnknownTable.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcIpBgpTmpAfPathAttrCounter		1.3.6.1.4.1.2272.1.8.101.17.11.3
The number of entries in the rcIpBgpTmpAfPathAttrTable.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcIpBgpTmpAfPathAttrTable		1.3.6.1.4.1.2272.1.8.101.17.11.4
Provides per advertised network-prefix attribute data, as advertised over a peering session.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpBgpTmpAfPathAttrEntry

rcIpBgpTmpAfPathAttrEntry		1.3.6.1.4.1.2272.1.8.101.17.11.4.1
Each entry contains data about path attributes associated with a given prefix in the rcIpBgpTmpNlriTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpBgpTmpAfPathAttrEntry

rcIpBgpTmpAfPathAttrOrigin		1.3.6.1.4.1.2272.1.8.101.17.11.4.1.1
The ultimate origin of the path information.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	igp(1), egp(2), incomplete(3)

rcIpBgpTmpAfPathAttrNextHopAddrType		1.3.6.1.4.1.2272.1.8.101.17.11.4.1.2
The address family of the address for the border router that should be used to access the destination network.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddressType

rcIpBgpTmpAfPathAttrNextHopAddr		1.3.6.1.4.1.2272.1.8.101.17.11.4.1.3
The address of the border router that should be used to access the destination network. This address is the nexthop address received in the UPDATE packet associated with this prefix. Note that for RFC2545 style double nexthops, this object will always contain the global scope nexthop. bgpPathAttrLinkLocalNextHop will contain the linklocal scope nexthop, if it is present. In the case a mechanism is developed to use only a link local nexthop, rcIpBgpTmpAfPathAttrNextHopAddr will contain the link local nexthop.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddress	Size(4..20)

rcIpBgpTmpAfPathAttrLinkLocalNextHopAddrType		1.3.6.1.4.1.2272.1.8.101.17.11.4.1.4
The address type for IPv6 link local addresses. This is present only when receiving RFC 2545 style double nexthops. This object is optionally present in BGP implementations that do not support IPv6.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddressType

rcIpBgpTmpAfPathAttrLinkLocalNextHopAddr		1.3.6.1.4.1.2272.1.8.101.17.11.4.1.5
This value contains an IPv6 link local address and is present only when receiving RFC 2545 style double nexthops. This object is optionally present in BGP implementations that do not support IPv6.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddress

rcIpBgpTmpAfPathAttrMedPresent		1.3.6.1.4.1.2272.1.8.101.17.11.4.1.6
This value is true when the MED value was sent in the UPDATE message.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcIpBgpTmpAfPathAttrMed		1.3.6.1.4.1.2272.1.8.101.17.11.4.1.7
This metric is used to discriminate between multiple exit points to an adjacent autonomous system. When the MED value is absent but has a calculated default value, this object will contain the calculated value.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcIpBgpTmpAfPathAttrLocalPref		1.3.6.1.4.1.2272.1.8.101.17.11.4.1.8
The originating BGP4 speakers degree of preference for an advertised route. If the route was not sent with a LOCAL_PREF value, this object will be absent.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcIpBgpTmpAfPathAttrAtomicAggregate		1.3.6.1.4.1.2272.1.8.101.17.11.4.1.9
When this object is set to atomicAggregatePresent, the ATOMIC_AGGREGATE Path Attribute is present and indicates that the NLRI MUST NOT be made more specific.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	atomicAggregatePresent(1), atomicAggregateMissing(2)

rcIpBgpTmpAfPathAttrAggregatorAS		1.3.6.1.4.1.2272.1.8.101.17.11.4.1.10
The AS number of the last BGP4 speaker that performed route aggregation. If the AGGREGATOR path attribute is absent, this object will not be present in the conceptual row.
Status: current	Access: read-only
OBJECT-TYPE
	InetAutonomousSystemNumber

rcIpBgpTmpAfPathAttrAggregatorAddr		1.3.6.1.4.1.2272.1.8.101.17.11.4.1.11
The IP address of the last BGP4 speaker that performed route aggregation. If the AGGREGATOR path attribute is absent, this object will not be present in the conceptual row.
Status: current	Access: read-only
OBJECT-TYPE
	RcIpBgpTmpIdentifierTC

rcIpBgpTmpAsPathCalcLength		1.3.6.1.4.1.2272.1.8.101.17.11.4.1.12
This value represents the calculated length of the AS Path according to the rules of the BGP specification. This value is used in route selection.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcIpBgpTmpAsPathIndex		1.3.6.1.4.1.2272.1.8.101.17.11.4.1.13
This value is a unique index for the decomposed AS Path in the rcIpBgpTmpAsPathTable. It is assigned by the agent at the point of creation of the rcIpBgpTmpAsPathTable row entry. While its value is guaranteed to be unique at any time, it is otherwise opaque to the management application with respect to its value or the contiguity of rcIpBgpTmpAsPathIndex row instance values across rows of the rcIpBgpTmpAsPathTable.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcIpBgpTmpAsPathString		1.3.6.1.4.1.2272.1.8.101.17.11.4.1.14
This is a string depicting the autonomous system path to this network which was received from the peer which advertised it. The format of the string is implementation-dependent, and should be designed for operator readability. Note that SnmpAdminString is only capable of representing a maximum of 255 characters. This may lead to the string being truncated in the presence of a large AS Path. The rcIpBgpTmpAsPathTable will give access to the full AS Path.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString

rcIpBgpTmpExtensions		1.3.6.1.4.1.2272.1.8.101.17.12
OBJECT IDENTIFIER

rcIpBgpTmpNotification		1.3.6.1.4.1.2272.1.8.101.17.0
OBJECT IDENTIFIER

rcIpBgpTmpEstablishedNotification		1.3.6.1.4.1.2272.1.8.101.17.0.1
The rcIpBgpTmpEstablishedNotification event is generated when the BGP FSM enters the established state. This Notification replaces the bgpEstablished Notification and has been replaced by rcIpBgpTmpAfEstablishedNotification.
Status: deprecated	Access: read-only
NOTIFICATION-TYPE

rcIpBgpTmpBackwardTransNotification		1.3.6.1.4.1.2272.1.8.101.17.0.2
The rcIpBgpBackwardTransNotification event is generated when the BGP FSM moves from a higher numbered state to a lower numbered state. This Notification replaces the bgpBackwardsTransition Notification and has been replaced by rcIpBgpTmpAfBackwardsNotification.
Status: deprecated	Access: read-only
NOTIFICATION-TYPE

rcIpBgpTmpAfEstablishedNotification		1.3.6.1.4.1.2272.1.8.101.17.0.3
The BGP Established event is generated when the BGP FSM enters the established state.
Status: current	Access: read-only
NOTIFICATION-TYPE

rcIpBgpTmpAfBackwardTransitionNotification		1.3.6.1.4.1.2272.1.8.101.17.0.4
The BGPBackwardTransition Event is generated when the BGP FSM moves from a higher numbered state to a lower numbered state. Due to the nature of the BGP state machine, an implementation MAY rate limit the generation of this event. An implementation MAY also generate this notification ONLY when the state machine moves out of the established state. An implementation should document its specific behavior.
Status: current	Access: read-only
NOTIFICATION-TYPE

rcIpBfd		1.3.6.1.4.1.2272.1.8.104
OBJECT IDENTIFIER

rcIpBfdTrapEnabled		1.3.6.1.4.1.2272.1.8.104.1
Used to indicate whether BFD traps should be sent or not
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpBfdHoldOffTimerInterval		1.3.6.1.4.1.2272.1.8.104.2
This object specifies the hold off timer interval, in seconds. 0 means that hold off timer is disabled.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0..65535

rcBfdTmpMib		1.3.6.1.4.1.2272.1.81.1
OBJECT IDENTIFIER

rcBfdTmpNotifications		1.3.6.1.4.1.2272.1.81.1.0
OBJECT IDENTIFIER

rcBfdTmpObjects		1.3.6.1.4.1.2272.1.81.1.1
OBJECT IDENTIFIER

rcBfdTmpScalarObjects		1.3.6.1.4.1.2272.1.81.1.1.1
OBJECT IDENTIFIER

rcBfdTmpAdminStatus		1.3.6.1.4.1.2272.1.81.1.1.1.1
The global administrative status of BFD in this router. The value 'enabled' denotes that the BFD Process is active on at least one interface; 'disabled' disables it on all interfaces.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

rcBfdTmpVersionNumber		1.3.6.1.4.1.2272.1.81.1.1.1.3
The current version number of the BFD protocol.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcBfdTmpSessTable		1.3.6.1.4.1.2272.1.81.1.1.2
The BFD Session Table describes the BFD sessions.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcBfdTmpSessEntry

rcBfdTmpSessEntry		1.3.6.1.4.1.2272.1.81.1.1.2.1
The BFD Session Entry describes BFD session.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcBfdTmpSessEntry

rcBfdTmpSessIndex		1.3.6.1.4.1.2272.1.81.1.1.2.1.1
This object contains an index used to represent a unique BFD session on this device.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcBfdTmpSessIndexTC

rcBfdTmpSessApplicationId		1.3.6.1.4.1.2272.1.81.1.1.2.1.2
This object contains an index used to indicate a local application which owns or maintains this BFD session. For instance, the MPLS VPN process may maintain a subset of the total number of BFD sessions. This application ID provides a convenient way to segregate sessions by the applications which maintain them.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcBfdTmpSessDiscriminator		1.3.6.1.4.1.2272.1.81.1.1.2.1.3
This object specifies the local discriminator for this BFD session, used to uniquely identify it.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	1..4294967295

rcBfdTmpSessRemoteDiscr		1.3.6.1.4.1.2272.1.81.1.1.2.1.4
This object specifies the session discriminator chosen by the remote system for this BFD session.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	1..4294967295

rcBfdTmpSessUdpPort		1.3.6.1.4.1.2272.1.81.1.1.2.1.5
The UDP Port for BFD. The default value is the well-known value for this port.
Status: current	Access: read-create
OBJECT-TYPE
	InetPortNumber

rcBfdTmpSessState		1.3.6.1.4.1.2272.1.81.1.1.2.1.6
The perceived state of the BFD session.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	adminDown(1), down(2), init(3), up(4)

rcBfdTmpSessRemoteHeardFlag		1.3.6.1.4.1.2272.1.81.1.1.2.1.7
This object specifies status of BFD packet reception from the remote system. Specifically, it is set to true(1) if the local system is actively receiving BFD packets from the remote system, and is set to false(0) if the local system has not received BFD packets recently (within the detection time) or if the local system is attempting to tear down the BFD session.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcBfdTmpSessDiag		1.3.6.1.4.1.2272.1.81.1.1.2.1.8
A diagnostic code specifying the local system's reason for the last transition of the session from up(1) to some other state.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Unsigned32

rcBfdTmpSessOperMode		1.3.6.1.4.1.2272.1.81.1.1.2.1.9
This object specifies current operating mode that BFD session is operating in. A value of AsyncModeWEchoFun(1) ... A value of AsynchModeWOEchoFun(2) ... A value of DemandModeWEchoFunction(3) ... A value of DemandModeWOEchoFunction(4) ...
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	asyncModeWEchoFun(1), asynchModeWOEchoFun(2), demandModeWEchoFunction(3), demandModeWOEchoFunction(4)

rcBfdTmpSessDemandModeDesiredFlag		1.3.6.1.4.1.2272.1.81.1.1.2.1.10
This object indicates that the local system's desire to use Demand mode. Specifically, it is set to true(1) if the local system wishes to use Demand mode or false(0) if not
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcBfdTmpSessEchoFuncModeDesiredFlag		1.3.6.1.4.1.2272.1.81.1.1.2.1.11
This object indicates that the local system's desire to use Echo mode. Specifically, it is set to true(1) if the local system wishes to use Echo mode or false(0) if not
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcBfdTmpSessControlPlanIndepFlag		1.3.6.1.4.1.2272.1.81.1.1.2.1.12
This object indicates that the local system's ability to continue to function through a disruption of the control plane. Specifically, it is set to true(1) if the local system BFD implementation is independent of the control plane. Otherwise, the value is set to false(0)
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcBfdTmpSessAddrType		1.3.6.1.4.1.2272.1.81.1.1.2.1.13
This object specifies IP address of the interface associated with this BFD session. Only values unknown(0), ipv4(1) or ipv6(2) have to be supported. A value of unknown(0) is allowed only when the outgoing interface is of type point-to-point, or when the BFD session is not associated with a specific interface. If any other unsupported values are attempted in a set operation, the agent MUST return an inconsistentValue error.
Status: current	Access: read-create
OBJECT-TYPE
	InetAddressType

rcBfdTmpSessAddr		1.3.6.1.4.1.2272.1.81.1.1.2.1.14
This object specifies IP address of the interface associated with this BFD session. It can also be used to enabled BFD on a specific interface. The value is set to zero when BFD session is not associated with a specific interface.
Status: current	Access: read-create
OBJECT-TYPE
	InetAddress

rcBfdTmpSessDesiredMinTxInterval		1.3.6.1.4.1.2272.1.81.1.1.2.1.15
This object specifies the minimum interval, in microseconds, that the local system would like to use when transmitting BFD Control packets.
Status: current	Access: read-create
OBJECT-TYPE
	RcBfdTmpInterval

rcBfdTmpSessReqMinRxInterval		1.3.6.1.4.1.2272.1.81.1.1.2.1.16
This object specifies the minimum interval, in microseconds, between received BFD Control packets the local system is capable of supporting.
Status: current	Access: read-create
OBJECT-TYPE
	RcBfdTmpInterval

rcBfdTmpSessReqMinEchoRxInterval		1.3.6.1.4.1.2272.1.81.1.1.2.1.17
This object specifies the minimum interval, in microseconds, between received BFD Echo packets that this system is capable of supporting.
Status: current	Access: read-create
OBJECT-TYPE
	RcBfdTmpInterval

rcBfdTmpSessDetectMult		1.3.6.1.4.1.2272.1.81.1.1.2.1.18
This object specifies the Detect time multiplier.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

rcBfdTmpSessStorType		1.3.6.1.4.1.2272.1.81.1.1.2.1.19
This variable indicates the storage type for this object. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row.
Status: current	Access: read-create
OBJECT-TYPE
	StorageType

rcBfdTmpSessRowStatus		1.3.6.1.4.1.2272.1.81.1.1.2.1.20
This variable is used to create, modify, and/or delete a row in this table. When a row in this table has a row in the active(1) state, no objects in this row can be modified except the bfdSessRowStatus and bfdSessStorageType.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcBfdTmpSessAuthPresFlag		1.3.6.1.4.1.2272.1.81.1.1.2.1.21
This object indicates that the local system's desire to use Authentication. Specifically, it is set to true(1) if the local system wishes the session to be authenticated or false(0) if not
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcBfdTmpSessAuthenticationType		1.3.6.1.4.1.2272.1.81.1.1.2.1.22
The Authentication Type used for this BFD session. This field is valid only when the Authentication Present bit is set
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	simplePassword(1), keyedMD5(2), meticulousKeyedMD5(3), keyedSHA1(4), meticulousKeyedSHA1(5)

rcBfdTmpSessPerfTable		1.3.6.1.4.1.2272.1.81.1.1.3
This table specifies BFD Session performance counters.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcBfdTmpSessPerfEntry

rcBfdTmpSessPerfEntry		1.3.6.1.4.1.2272.1.81.1.1.3.1
An entry in this table is created by a BFD-enabled node for every BFD Session. bfdCounterDiscontinuityTime is used to indicate potential discontinuity for all counter objects in this table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcBfdTmpSessPerfEntry

rcBfdTmpSessPerfPktIn		1.3.6.1.4.1.2272.1.81.1.1.3.1.1
The total number of BFD messages received for this BFD session.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcBfdTmpSessPerfPktOut		1.3.6.1.4.1.2272.1.81.1.1.3.1.2
The total number of BFD messages sent for this BFD session.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcBfdTmpSessUpTime		1.3.6.1.4.1.2272.1.81.1.1.3.1.3
The value of sysUpTime on the most recent occasion at which the session came up. If no such up event exists this object contains a zero value.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

rcBfdTmpSessPerfLastSessDownTime		1.3.6.1.4.1.2272.1.81.1.1.3.1.4
The value of sysUpTime on the most recent occasion at which the last time communication was lost with the neighbor. If no such down event exist this object contains a zero value.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

rcBfdTmpSessPerfLastCommLostDiag		1.3.6.1.4.1.2272.1.81.1.1.3.1.5
The BFD diag code for the last time communication was lost with the neighbor. If no such down event exists this object contains a zero value.
Status: current	Access: read-only
OBJECT-TYPE
	RcBfdTmpDiag

rcBfdTmpSessPerfSessUpCount		1.3.6.1.4.1.2272.1.81.1.1.3.1.6
The number of times this session has gone into the Up state since the router last rebooted.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcBfdTmpSessPerfDiscTime		1.3.6.1.4.1.2272.1.81.1.1.3.1.7
The value of sysUpTime on the most recent occasion at which any one or more of the session counters suffered a discontinuity. The relevant counters are the specific instances associated with this BFD session of any Counter32 object contained in the BfdSessPerfTable. If no such discontinuities have occurred since the last re-initialization of the local management subsystem, then this object contains a zero value.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

rcBfdTmpSessPerfPktInHC		1.3.6.1.4.1.2272.1.81.1.1.3.1.8
This value represents the total number of BFD messages received for this BFD session. It MUST be equal to the least significant 32 bits of bfdSessPerfPktIn if bfdSessPerfPktInHC is supported according to the rules spelled out in RFC2863.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcBfdTmpSessPerfPktOutHC		1.3.6.1.4.1.2272.1.81.1.1.3.1.9
This value represents the total number of total number of BFD messages transmitted for this BFD session. It MUST be equal to the least significant 32 bits of bfdSessPerfPktIn if bfdSessPerfPktOutHC is supported according to the rules spelled out in RFC2863.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcBfdTmpSessMapTable		1.3.6.1.4.1.2272.1.81.1.1.4
The BFD Session Mapping Table maps the complex indexing of the BFD sessions to the flat BFDIndex used in the BfdSessionTable. Implementors need to be aware that if the value of the bfdSessAddr (an OID) has more that 111 sub-identifiers, then OIDs of column instances in this table will have more than 128 sub-identifiers and cannot be accessed using SNMPv1, SNMPv2c, or SNMPv3.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcBfdTmpSessMapEntry

rcBfdTmpSessMapEntry		1.3.6.1.4.1.2272.1.81.1.1.4.1
The BFD Session Entry describes BFD session that is mapped to this index. Implementors need to be aware that if the value of the mplsInSegmentMapLabelPtrIndex (an OID) has more that 111 sub-identifiers, then OIDs of column instances in this table will have more than 128 sub-identifiers and cannot be accessed using SNMPv1, SNMPv2c, or SNMPv3.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcBfdTmpSessMapEntry

rcBfdTmpSessMapBfdIndex		1.3.6.1.4.1.2272.1.81.1.1.4.1.1
This object specifies the BfdIndex referred to by the indexes of this row. In essence, a mapping is provided between these indexes and the BfdSessTable.
Status: current	Access: read-only
OBJECT-TYPE
	RcBfdTmpSessIndexTC

rcBfdTmpSessNotificationsEnable		1.3.6.1.4.1.2272.1.81.1.1.1.4
If this object is set to true(1), then it enables the emission of bfdSessUp and bfdSessDown notifications; otherwise these notifications are not emitted.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcBfdTmpSessUp		1.3.6.1.4.1.2272.1.81.1.0.1
This notification is generated when the bfdSessState object for one or more contiguous entries in bfdSessTable are about to enter the up(2) state from some other state. The included values of bfdSessDiag MUST both be set equal to this new state (i.e: up(1)). The two instances of bfdSessDiag in this notification indicate the range of indexes that are affected. Note that all the indexes of the two ends of the range can be derived from the instance identifiers of these two objects. For the cases where a contiguous range of sessions have transitioned into the up(1) state at roughly the same time, the device SHOULD issue a single notification for each range of contiguous indexes in an effort to minimize the emission of a large number of notifications. If a notification has to be issued for just a single bfdSessEntry, then the instance identifier (and values) of the two bfdSessDiag objects MUST be the identical.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcBfdTmpSessDown		1.3.6.1.4.1.2272.1.81.1.0.2
This notification is generated when the bfdSessState object for one or more contiguous entries in bfdSessTable are about to enter the down(4) or adminDown(5) states from some other state. The included values of bfdSessDiag MUST both be set equal to this new state (i.e: down(4) or adminDown(5)). The two instances of bfdSessDiag in this notification indicate the range of indexes that are affected. Note that all the indexes of the two ends of the range can be derived from the instance identifiers of these two objects. For cases where a contiguous range of sessions have transitioned into the down(4) or adminDown(5) states at roughly the same time, the device SHOULD issue a single notification for each range of contiguous indexes in an effort to minimize the emission of a large number of notifications. If a notification has to be issued for just a single bfdSessEntry, then the instance identifier (and values) of the two bfdSessDiag objects MUST be the identical.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcBfdExtMib		1.3.6.1.4.1.2272.1.81.2
OBJECT IDENTIFIER

rcBfdExtObjects		1.3.6.1.4.1.2272.1.81.2.1
OBJECT IDENTIFIER

rcBfdExtSessTable		1.3.6.1.4.1.2272.1.81.2.1.1
The BFD Session Extension Table describes the BFD sessions.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcBfdExtSessEntry

rcBfdExtSessEntry		1.3.6.1.4.1.2272.1.81.2.1.1.1
The BFD Session Extension Entry describes BFD session.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcBfdExtSessEntry

rcBfdExtSessPeerState		1.3.6.1.4.1.2272.1.81.2.1.1.1.1
The perceived peer state of the BFD session.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	adminDown(1), down(2), init(3), up(4)

rcBfdExtSessPeerAddrType		1.3.6.1.4.1.2272.1.81.2.1.1.1.2
Inet Address Type of peer IP address associated with this BFD session.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddressType

rcBfdExtSessPeerAddr		1.3.6.1.4.1.2272.1.81.2.1.1.1.3
This object specifies peer IP address associated with this BFD session.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddress

rcBfdExtSessApp		1.3.6.1.4.1.2272.1.81.2.1.1.1.4
This object specifies the applications configured on this BFD session.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString	Size(0..64)

rcBfdExtSessAppRun		1.3.6.1.4.1.2272.1.81.2.1.1.1.5
This object specifies the applications running on this BFD session.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString	Size(0..64)

rcKhiConfig		1.3.6.1.4.1.2272.1.85.1
OBJECT IDENTIFIER

rcKhiConfigKhiAdminState		1.3.6.1.4.1.2272.1.85.1.1
Key Health Inidaction, this object is used turn off the KHI feature administratively. true(1) means On, false(2) means off. By default, it is always set to true(1).
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcKhiConfigKhiBootDelay		1.3.6.1.4.1.2272.1.85.1.2
Time interval from system up and running to start the KHI feature. Set to 0 to disable to the time interval.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0..60

rcKhiConfigClearAction		1.3.6.1.4.1.2272.1.85.1.3
Clear action with bits set. 0 Bit means from left (most sinificant) bit to right (less sinificnt) bit
Status: current	Access: read-write
OBJECT-TYPE
	BITS	chassis(0), performance(1), port(2), forwarding(3), ip(4), protocol(5), mgmt(6)

rcKhiConfigPortKhiAdminState		1.3.6.1.4.1.2272.1.85.1.4
Key Health Inidcation, this object is used turn off the Port KHI feature administratively. true(1) means On, false(2) means off. By default, it is always set to true(1).
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcKhiConfigPerfKhiAdminState		1.3.6.1.4.1.2272.1.85.1.5
Key Health Inidcation, this object is used turn off the Performance KHI feature administratively. true(1) means On, false(2) means off. By default, it is always set to true(1).
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcKhiConfigChasKhiAdminState		1.3.6.1.4.1.2272.1.85.1.6
Key Health Inidcation, this object is used turn off the Chassis KHI feature administratively. true(1) means On, false(2) means off. By default, it is always set to true(1).
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcKhiConfigForwardingKhiAdminState		1.3.6.1.4.1.2272.1.85.1.7
Key Health Inidcation, this object is used turn off the Forwarding KHI feature administratively. true(1) means On, false(2) means off. By default, it is always set to true(1).
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcKhiConfigMgmtKhiAdminState		1.3.6.1.4.1.2272.1.85.1.8
Key Health Inidcation, this object is used turn off the Management KHI feature administratively. true(1) means On, false(2) means off. By default, it is always set to true(1).
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcKhiHighLevel		1.3.6.1.4.1.2272.1.85.2
OBJECT IDENTIFIER

rcKhiHighLevelKhiOperStatus		1.3.6.1.4.1.2272.1.85.2.1
Indicate if the KHI feature is on(1), off(2) or wait(3). running (1) means KHI is enabled and running. off(2) means KHI is disabled wait(3) means KHI is enabled but it is not running yet. At beginning of system boot up, KHI can be set to wait for start time (rcKhiHighLevelKhiStartTime) to experied then start the KHI monitor the system. This allows the system fully up and start the KHI info. When Operation Status is off or wait, all KHI status will not be valid
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	running(1), off(2), wait(3)

rcKhiHighLevelChassisCurrentStatus		1.3.6.1.4.1.2272.1.85.2.2
Chassis current status. Include: Chassis Temperature, Fan Temperature and operational status, Line card operational status, Mezz operational status, HA status. This object show GREEN when all of above are GREEN. Otherwise, it will show the highest alert in ther order of Red, Yellow, or Green green(1): All Chassis parameters are normal. yellow(2): One of chassis parameter in alert state red(3): One or more Chassis parameters are in critical state.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiHighLevelChassisFirstHighestEvent		1.3.6.1.4.1.2272.1.85.2.3
The first highest alert changing of chassis status since last boot or last clear (rcKhiConfigClearAction). green(1): All Chassis parameters were normal. yellow(2): One or more Chassis parameter has changed. red(3): One or more Chassis parameters were in critical state.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiHighLevelChassisFirstHighestEventTime		1.3.6.1.4.1.2272.1.85.2.4
Timestamp of first highest alert of chassis status indication (rcKhiHighLevelChassisChangeStatus)
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiHighLevelChassisRefStatus		1.3.6.1.4.1.2272.1.85.2.5
Chassis reference status before the first the first change and since last boot or last clear (rcKhiConfigClearAction). green(1): All Chassis parameters were normal. yellow(2): One or more Chassis parameter has changed. red(3): One or more Chassis parameters were in critical state.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiHighLevelChassisStatusLastClearTime		1.3.6.1.4.1.2272.1.85.2.6
chassis status last clear time stamp
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiHighLevelCpuPerfCurrentStatus		1.3.6.1.4.1.2272.1.85.2.7
Current CPU Performance Status. Inlcudes: CPU utilization, Fabric utilization, Buffer utilization, Dram Size, Suspended task, CPU control status. green(1): All chassis parameter are normal yellow(2): One or more Chassis parameters have changed. red(3): One or more Chassis parameters are in critical state.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiHighLevelCpuPerfFirstHighestEvent		1.3.6.1.4.1.2272.1.85.2.8
The first highest alert change of CPU performance status since last boot or last clear (rcKhiConfigClearAction). green(1): All Chassis parameters were normal. yellow(2): One or more Chassis parameter has changed. red(3): One or more Chassis parameters are in critical state.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiHighLevelCpuPerfFirstHighestEventTime		1.3.6.1.4.1.2272.1.85.2.9
Timestamp of first highest alert change of CPU Performance status (rcKhiHighLevelCpuPerfChangeStatus)
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiHighLevelCpuPerfRefStatus		1.3.6.1.4.1.2272.1.85.2.10
CPU performance reference status before the first change since last boot or last clear (rcKhiConfigClearAction). green(1): All Chassis parameters were normal. yellow(2): One or more Chassis parameter has changed. red(3): One or more Chassis parameters are in critical state.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiHighLevelCpuPerfStatusLastClearTime		1.3.6.1.4.1.2272.1.85.2.11
CPU Performance last clear time stamp
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiHighLevelPortCurrentStatus		1.3.6.1.4.1.2272.1.85.2.12
Ports current status. green(1): Port link state has no change. yellow(2): Port link state is changed by admin. red(3): Port link state is in critical state.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiHighLevelPortFirstHighestEvent		1.3.6.1.4.1.2272.1.85.2.13
The first highest change indication of ports status since last boot or last clear (rcKhiConfigClearAction). green(1): Port link state had no change. yellow(2): Port link state was changed by admin. red(3): Port link state was in critical state.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiHighLevelPortFirstHighestEventTime		1.3.6.1.4.1.2272.1.85.2.14
Timestamp of first highest inidcation of Ports status status indication (rcKhiHighLevelPortChangeStatus)
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiHighLevelPortRefStatus		1.3.6.1.4.1.2272.1.85.2.15
Ports reference status before first change since last boot or last clear (rcKhiConfigClearAction). green(1): Port link state had no change. yellow(2): Port link state was changed by admin. red(3): Port link state was in critical state.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiHighLevelPortStatusLastClearTime		1.3.6.1.4.1.2272.1.85.2.16
Ports status last clear time stamp
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiHighLevelForwardingCurrentStatus		1.3.6.1.4.1.2272.1.85.2.17
Forwarding current status. green(1): Port link state has no change. yellow(2): Port link state is changed by admin. red(3): Port link state is in critical state.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiHighLevelForwardingFirstHighestEvent		1.3.6.1.4.1.2272.1.85.2.18
The frist highest changing inidcation of Forwarding status since last boot or clear. green(1): Port link state had no change. yellow(2): Port link state was changed by admin. red(3): Port link state was in critical state.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiHighLevelForwardingFirstHighestEventTime		1.3.6.1.4.1.2272.1.85.2.19
Timestamp of first highest inidcation of Forwarding status status indication (rcKhiHighLevelForwardingChangeStatus)
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiHighLevelForwardingRefStatus		1.3.6.1.4.1.2272.1.85.2.20
Forwarding reference status before the first change since last boot or clear. green(1): Port link state had no change. yellow(2): Port link state was changed by admin. red(3): Port link state was in critical state.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiHighLevelForwardingStatusLastClearTime		1.3.6.1.4.1.2272.1.85.2.21
Forwarding status last clear time stamp
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiHighLevelTotalConfigVlanCount		1.3.6.1.4.1.2272.1.85.2.22
Total Number of Vlan configured in device
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiHighLevelTotalConfigIpIfCount		1.3.6.1.4.1.2272.1.85.2.23
Total Configured IP Interface count
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiHighLevelTotalOperIpIfCurrentCount		1.3.6.1.4.1.2272.1.85.2.24
Current total operational IP Interface count
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiHighLevelIpIfFirstChangeTime		1.3.6.1.4.1.2272.1.85.2.25
Timestamp of first change of IP interface
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiHighLevelTotalOperIpIfReferenceCount		1.3.6.1.4.1.2272.1.85.2.26
Reference count of total operational IP berfore the first change since last boot or last clear
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiHighLevelIpIfLastClearTime		1.3.6.1.4.1.2272.1.85.2.27
IP interface last clear time stamp
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiHighLevelGlobalRouterTotalRouteCount		1.3.6.1.4.1.2272.1.85.2.28
Total number of route count in VRF 0, which is default VRF
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiHighLevelGlobalRouterTotalRouteRefCount		1.3.6.1.4.1.2272.1.85.2.29
Total number of route reference count in VRF 0, which is default VRF
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiHighLevelGlobalRouterLastClearTime		1.3.6.1.4.1.2272.1.85.2.30
Global router total routes last clear time stamp
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiHighLevelGlobalRouterTotalBestRouteCount		1.3.6.1.4.1.2272.1.85.2.31
total number of best route count in VRF 0 (default VRF)
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiHighLevelGlobalRouterBestRouteRefCount		1.3.6.1.4.1.2272.1.85.2.32
Total number of best route reference count in VRF 0, which is default VRF
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiHighLevelGlobalRouterBestRouteLastClearTime		1.3.6.1.4.1.2272.1.85.2.33
Global router total best routes last clear time stamp
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiHighLevelNonZeroVrfsTotalRouteCount		1.3.6.1.4.1.2272.1.85.2.34
Total number of route count in Non Zero Vrfs
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiHighLevelNonZeroVrfsTotalRouteRefCount		1.3.6.1.4.1.2272.1.85.2.35
Total number of route reference count in non zero VRF
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiHighLevelNonZeroVrfsRouteLastClearTime		1.3.6.1.4.1.2272.1.85.2.36
Non zero vrf total routes last clear time stamp
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiHighLevelNonZeroVrfsTotalBestRouteCount		1.3.6.1.4.1.2272.1.85.2.37
total number of best route count in Non Zero Vrfs
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiHighLevelNonZeroVrfsBestRouteRefCount		1.3.6.1.4.1.2272.1.85.2.38
Total number of best route reference count in non zero VRF
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiHighLevelNonZeroVrfsBestRouteLastClearTime		1.3.6.1.4.1.2272.1.85.2.39
Non zero vrf total best routes last clear time stamp
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiHighLevelFdbRecordCount		1.3.6.1.4.1.2272.1.85.2.40
This count includes the number of FDB entries in the CP (Control card) database, it includes the local and remote learnt MACs via IST/SMLT, it is not the actual record count on the line card.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiHighLevelFdbRecordRefCount		1.3.6.1.4.1.2272.1.85.2.41
Total number of fdb record reference count
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiHighLevelFdbRecordLastClearTime		1.3.6.1.4.1.2272.1.85.2.42
FDB Records Last clear time
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiHighLevelGlobalRouterProtocolState		1.3.6.1.4.1.2272.1.85.2.43
Global Router Protocol State
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiHighLevelGlobalRouterProtocolStateLastClearTime		1.3.6.1.4.1.2272.1.85.2.44
GR Protocol State last clear time
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiHighLevelNonZeroVrfsProtocolState		1.3.6.1.4.1.2272.1.85.2.45
Non zero VRF Protocol State
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiHighLevelNonZeroVrfsProtocolStateLastClearTime		1.3.6.1.4.1.2272.1.85.2.46
Nonzero vrf Protocol State last clear time
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiHighLevelIstCurrentStatus		1.3.6.1.4.1.2272.1.85.2.47
Key Health Indicction, IST current status
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiHighLevelIstFirstHighestEvent		1.3.6.1.4.1.2272.1.85.2.48
Key Health Indicction, IST changing status since last boot or clear
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiHighLevelIstFirstHighestEventTime		1.3.6.1.4.1.2272.1.85.2.49
Timestamp of first change Ist Status
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiHighLevelIstStatusLastClearTime		1.3.6.1.4.1.2272.1.85.2.50
Ist Status last Clear timestamp
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiHighLevelSmltOperPortsCount		1.3.6.1.4.1.2272.1.85.2.51
Current total numbers of SMLT operational ports
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiHighLevelSmltOperPortsChangeTime		1.3.6.1.4.1.2272.1.85.2.52
Timestamp of first change Smlt operational ports
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiHighLevelSmltOperPortsReferenceCount		1.3.6.1.4.1.2272.1.85.2.53
Reference count of SMLT operational ports before the first chaneg since last boot or clear
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiHighLevelSmltOperPortsLastClearTime		1.3.6.1.4.1.2272.1.85.2.54
SMLT operational ports count last Clear timestamp
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiHighLevelTotalSmltConfigPorts		1.3.6.1.4.1.2272.1.85.2.55
Total number of SMLT configured ports
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiHighLevelLogCurrentStatus		1.3.6.1.4.1.2272.1.85.2.56
Logging task current status
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiHighLevelLogFirstHighestEvent		1.3.6.1.4.1.2272.1.85.2.57
The highest inidcation of the first change of logging task status since last boot or clear
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiHighLevelLogFirstHighestEventTime		1.3.6.1.4.1.2272.1.85.2.58
Timestamp of first change logging task Status
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiHighLevelLogRefStatus		1.3.6.1.4.1.2272.1.85.2.59
log referemce status before the first change since last boot or clear
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiHighLevelLogStatusLastClearTime		1.3.6.1.4.1.2272.1.85.2.60
Ist Status last Clear timestamp
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiHighLevelNumOfTcpConnection		1.3.6.1.4.1.2272.1.85.2.61
Total number of TCP connections
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiHighLevelNumOfActiveTcpConnection		1.3.6.1.4.1.2272.1.85.2.62
Total number of TCP connections which is establish
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiHighLevelNumOfCliUsers		1.3.6.1.4.1.2272.1.85.2.63
Total number of CLI sesssion
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiChassis		1.3.6.1.4.1.2272.1.85.3
OBJECT IDENTIFIER

rcKhiChassisChasTemperature		1.3.6.1.4.1.2272.1.85.3.1
Used to indicate the core operating temperature of the chassis. This value represents the degree in celsius of the air inside the chassis.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcKhiChassisTemperatureFirstHigherAlert		1.3.6.1.4.1.2272.1.85.3.2
Used to indicate the the first higher temperature alert of the chassis since last boot or clear. The value is the degree in celsius.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcKhiChassisTemperatureFirstHigherAlertTime		1.3.6.1.4.1.2272.1.85.3.3
The time at which the first higher temperature alert occur.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiChassisChasTemperatureStatusIndication		1.3.6.1.4.1.2272.1.85.3.4
KHI Status indication
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiChassisMasterCpuMezzOperState		1.3.6.1.4.1.2272.1.85.3.5
Used to indicate the CPU Mezz card
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unsupported(1), notPresent(2), present(3), running(4)

rcKhiChassisMasterCpuMezzStatusIndication		1.3.6.1.4.1.2272.1.85.3.6
the CPU Mezz card status indication
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiChassisStandbyCpuMezzOperState		1.3.6.1.4.1.2272.1.85.3.7
Used to indicate the CPU Mezz card
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unsupported(1), notPresent(2), present(3), running(4)

rcKhiChassisStandbyCpuMezzStatusIndication		1.3.6.1.4.1.2272.1.85.3.8
Used to indicate the CPU Mezz card
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiChassisStandbyCpuState		1.3.6.1.4.1.2272.1.85.3.9
Indicate the standby-CPU state. initialization - indicate the CPU is in this state (1). oneWayActive - Modules that need to be synchronized have registered with the framework (either locally or a message was received from remote CPU (2). twoWayActive - Modules that need to be synchronized have registered with the framework (either locally or a message was received from remote CPU (3). synchronized - Table based synchroniztion was completed on the current CPU (4). remoteIncompatible - CPUs framework version is incompatible with the remote CPU (5). error - If an invalid event is generated in a given state the CPU enters Error state (6). disabled - High Availability is not enabled (7). peerNotConnected - no peer connection is established (8). peerConnected - peer connection is established (9). lostPeerConnection - lost connection to peer/Standby CPU (10). notSynchronized - Table Sync is not complete (11).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	initialization(1), oneWayActive(2), twoWayActive(3), synchronized(4), remoteIncompatible(5), error(6), disabled(7), peerNotConnected(8), peerConnected(9), lostPeerConnection(10), notSynchronized(11)

rcKhiChassisStandbyCpuStatusIndication		1.3.6.1.4.1.2272.1.85.3.10
the Ha-CPU status indicaton
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiChassisHistoryTable		1.3.6.1.4.1.2272.1.85.3.11
Chassis table include chassis history info
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcKhiChassisHistoryEntry

rcKhiChassisHistoryEntry		1.3.6.1.4.1.2272.1.85.3.11.1
A chassis history table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcKhiChassisHistoryEntry

rcKhiChassisHistoryIndex		1.3.6.1.4.1.2272.1.85.3.11.1.1
history index for chassis
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..10

rcKhiChassisHistoryTemperatureStateChange		1.3.6.1.4.1.2272.1.85.3.11.1.2
Chassis temperature state change. Green if temperature <=40, Yellow if temperature >=41 and <50 and Red if temperature >=50
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiChassisHistoryTemperatureStateChangeTime		1.3.6.1.4.1.2272.1.85.3.11.1.3
Time at which the temperature state change occur.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiChassisFanTable		1.3.6.1.4.1.2272.1.85.3.12
Fan table include Fan statistics
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcKhiChassisFanEntry

rcKhiChassisFanEntry		1.3.6.1.4.1.2272.1.85.3.12.1
A chassis fan table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcKhiChassisFanEntry

rcKhiChassisFanId		1.3.6.1.4.1.2272.1.85.3.12.1.1
An unique index used to identify a particular fan in the system.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..2

rcKhiChassisFanOperState		1.3.6.1.4.1.2272.1.85.3.12.1.2
Fan operational state
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), up(2), down(3)

rcKhiChassisFanFirstStateChange		1.3.6.1.4.1.2272.1.85.3.12.1.3
Fan operational state first change after boot or clear.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), up(2), down(3)

rcKhiChassisFanFirstStateChangeTime		1.3.6.1.4.1.2272.1.85.3.12.1.4
Time at which the fan operational state first change occur.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiChassisFanOperStatusIndication		1.3.6.1.4.1.2272.1.85.3.12.1.5
Fan oper state status indication
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiChassisFanTemperature		1.3.6.1.4.1.2272.1.85.3.12.1.6
Fan 1 temperature
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcKhiChassisFanTempFirstHigherAlert		1.3.6.1.4.1.2272.1.85.3.12.1.7
Fan temperature first higher alert
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcKhiChassisFanTempFirstHigherAlertTime		1.3.6.1.4.1.2272.1.85.3.12.1.8
Time at which the fan temperature first higher alert occur
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiChassisFanTempStatusIndication		1.3.6.1.4.1.2272.1.85.3.12.1.9
Fan status indication
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiChassisFanOperHistoryTable		1.3.6.1.4.1.2272.1.85.3.13
Fan table include Fan operational state history info
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcKhiChassisFanOperHistoryEntry

rcKhiChassisFanOperHistoryEntry		1.3.6.1.4.1.2272.1.85.3.13.1
A chassis fan oper state history table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcKhiChassisFanOperHistoryEntry

rcKhiChassisFanOperHistoryFanId		1.3.6.1.4.1.2272.1.85.3.13.1.1
An unique index used to identify a particular fan in the system.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..2

rcKhiChassisFanOperHistoryIndex		1.3.6.1.4.1.2272.1.85.3.13.1.2
history index for a particular fan
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..10

rcKhiChassisFanOperHistoryStateChange		1.3.6.1.4.1.2272.1.85.3.13.1.3
Fan operational state change. Up - Green and Down - Red
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiChassisFanOperHistoryStateChangeTime		1.3.6.1.4.1.2272.1.85.3.13.1.4
Time at which the fan operational state change occur.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiChassisFanTempHistoryTable		1.3.6.1.4.1.2272.1.85.3.14
Fan table include Fan temperature history info
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcKhiChassisFanTempHistoryEntry

rcKhiChassisFanTempHistoryEntry		1.3.6.1.4.1.2272.1.85.3.14.1
A chassis fan Temperature history table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcKhiChassisFanTempHistoryEntry

rcKhiChassisFanTempHistoryFanId		1.3.6.1.4.1.2272.1.85.3.14.1.1
An unique index used to identify a particular fan in the system.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..2

rcKhiChassisFanTempHistoryIndex		1.3.6.1.4.1.2272.1.85.3.14.1.2
history index for a particular fan
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..10

rcKhiChassisFanTempHistoryTempStateChange		1.3.6.1.4.1.2272.1.85.3.14.1.3
Fan temperature state change. Green if temperature <=40, Yellow if temperature >=41 and <50 and Red if temperature >=50
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiChassisFanTempHistoryTempStateChangeTime		1.3.6.1.4.1.2272.1.85.3.14.1.4
Time at which the fan temperature state change occur.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiChassisPowerSupplyTable		1.3.6.1.4.1.2272.1.85.3.15
Power Supply table include Power Supply statistics
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcKhiChassisPowerSupplyEntry

rcKhiChassisPowerSupplyEntry		1.3.6.1.4.1.2272.1.85.3.15.1
A chassis fan table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcKhiChassisPowerSupplyEntry

rcKhiChassisPowerSupplyId		1.3.6.1.4.1.2272.1.85.3.15.1.1
An unique index used to identify a particular Power Supply in the system.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..3

rcKhiChassisPowerSupplyOperState		1.3.6.1.4.1.2272.1.85.3.15.1.2
Power Supply operational state
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), empty(2), up(3), down(4)

rcKhiChassisPowerSupplyFirstStateChange		1.3.6.1.4.1.2272.1.85.3.15.1.3
Power Supply operational state First change after boot or clear.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), empty(2), up(3), down(4)

rcKhiChassisPowerSupplyFirstStateChangeTime		1.3.6.1.4.1.2272.1.85.3.15.1.4
Time at which Power Supply State first change occur.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiChassisPowerSupplyStatusIndication		1.3.6.1.4.1.2272.1.85.3.15.1.5
Power Supply status indication
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiChassisPowerSupplyHistoryTable		1.3.6.1.4.1.2272.1.85.3.16
Power Supply table include power supply history info
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcKhiChassisPowerSupplyHistoryEntry

rcKhiChassisPowerSupplyHistoryEntry		1.3.6.1.4.1.2272.1.85.3.16.1
A chassis power supply history table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcKhiChassisPowerSupplyHistoryEntry

rcKhiChassisPowerSupplyHistoryPSId		1.3.6.1.4.1.2272.1.85.3.16.1.1
An unique index used to identify a particular PowerSupply in the system.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..2

rcKhiChassisPowerSupplyHistoryIndex		1.3.6.1.4.1.2272.1.85.3.16.1.2
history index for a particular power supply
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..10

rcKhiChassisPowerSupplyHistoryOperStateChange		1.3.6.1.4.1.2272.1.85.3.16.1.3
Power supply operational state change. Green if power supply comes up and Red if it goes down
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiChassisPowerSupplyHistoryOperStateChangeTime		1.3.6.1.4.1.2272.1.85.3.16.1.4
Time at which the power supply operational state change occur.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiChassisLineCardTable		1.3.6.1.4.1.2272.1.85.3.17
table include line card statistics
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcKhiChassisLineCardEntry

rcKhiChassisLineCardEntry		1.3.6.1.4.1.2272.1.85.3.17.1
A chassis line card table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcKhiChassisLineCardEntry

rcKhiChassisLineCardSlot		1.3.6.1.4.1.2272.1.85.3.17.1.1
An unique index used to identify a particular slot of line card in the system.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..10

rcKhiChassisLineCardOperState		1.3.6.1.4.1.2272.1.85.3.17.1.2
Line card operational state
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2), testing(3), unknown(4), dormant(5)

rcKhiChassisLineCardAdminState		1.3.6.1.4.1.2272.1.85.3.17.1.3
Line card administrative state
Status: current	Access: read-only
OBJECT-TYPE
	EnableValue

rcKhiChassisLineCardFirstStateChange		1.3.6.1.4.1.2272.1.85.3.17.1.4
Line card first operational state change after boot or clear.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiChassisLineCardFirstStateChangeTime		1.3.6.1.4.1.2272.1.85.3.17.1.5
The time at which line card first operational state change occur.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiChassisLineCardStatusIndication		1.3.6.1.4.1.2272.1.85.3.17.1.6
Line card Status indication
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiChassisLineCardHistoryTable		1.3.6.1.4.1.2272.1.85.3.18
Line card table include line card history info
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcKhiChassisLineCardHistoryEntry

rcKhiChassisLineCardHistoryEntry		1.3.6.1.4.1.2272.1.85.3.18.1
A chassis line card history table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcKhiChassisLineCardHistoryEntry

rcKhiChassisLineCardHistoryLCId		1.3.6.1.4.1.2272.1.85.3.18.1.1
An unique index used to identify a particular LineCard in the system.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..2

rcKhiChassisLineCardHistoryIndex		1.3.6.1.4.1.2272.1.85.3.18.1.2
history index for a particular line card
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..10

rcKhiChassisLineCardHistoryOperStateChange		1.3.6.1.4.1.2272.1.85.3.18.1.3
Line card operational state change. Green if operationally up. Yellow if operationally down and adminstratively disabled. Red if operationally down and adminstratively enabled
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiChassisLineCardHistoryOperStateChangeTime		1.3.6.1.4.1.2272.1.85.3.18.1.4
Time at which the line card operational state change occur.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiPerformance		1.3.6.1.4.1.2272.1.85.4
OBJECT IDENTIFIER

rcKhiPerformanceCurrentCpuUtil		1.3.6.1.4.1.2272.1.85.4.1
Current Percentage of CPU utilization in 5 minutes sampling. Status: Yellow: above 75 Green: below 75
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcKhiPerformanceFirstHigherCpuUtil		1.3.6.1.4.1.2272.1.85.4.2
FirstHigher Percentage of CPU utilization in 5 minutes sampling. Status: Yellow: above 75 Green: below 75
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcKhiPerformanceCpuUtilFirstHigherAlertTime		1.3.6.1.4.1.2272.1.85.4.3
Timestamp of the high cpu utilization
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiPerformanceCpuUtilStatus		1.3.6.1.4.1.2272.1.85.4.4
the high cpu utilization status
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiPerformanceCurrentSwitchFabricUtil		1.3.6.1.4.1.2272.1.85.4.5
Current Percentage of Switching Fabric utilization
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcKhiPerformanceFirstHigherSwitchFabricUtil		1.3.6.1.4.1.2272.1.85.4.6
FirstHigher Percentage of Switching Fabric utilization
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcKhiPerformanceSwitchFabricUtilFirstHigherAlertTime		1.3.6.1.4.1.2272.1.85.4.7
Timestamp of ciritcal Percentage of Switching Fabric utilization
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiPerformanceSwitchFabricUtilStatus		1.3.6.1.4.1.2272.1.85.4.8
Switch Fabric Utilization Status
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiPerformanceCurrentOtherSwitchFabricUtil		1.3.6.1.4.1.2272.1.85.4.9
Current Percentage of Other Switching Fabric utilization
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcKhiPerformanceFirstHigherOtherSwitchFabricUtil		1.3.6.1.4.1.2272.1.85.4.10
FirstHigher Percentage of Other Switching Fabric utilization
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcKhiPerformanceOtherSwitchFabricUtilFirstHigherAlertTime		1.3.6.1.4.1.2272.1.85.4.11
Timestamp of ciritcal percentage of other Switching Fabric utilization
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiPerformanceOtherSwitchFabricUtilStatus		1.3.6.1.4.1.2272.1.85.4.12
Other Switch Fabric Utilization Status
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiPerformanceCurrentBufferUtil		1.3.6.1.4.1.2272.1.85.4.13
Current Percentage of buffer utilization
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcKhiPerformanceFirstHigherBufferUtil		1.3.6.1.4.1.2272.1.85.4.14
FirstHigher Percentage of buffer utilization
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcKhiPerformanceBufferUtilFirstHigherAlertTime		1.3.6.1.4.1.2272.1.85.4.15
Timestamp of critical Percentage of buffer utilization
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiPerformanceBufferUtilStatus		1.3.6.1.4.1.2272.1.85.4.16
Buffer Utilization Status
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiPerformanceCurrentDRamUsed		1.3.6.1.4.1.2272.1.85.4.17
Current Percentage of used DRAM in Kbytes
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcKhiPerformanceFirstHigherDRamUsed		1.3.6.1.4.1.2272.1.85.4.18
FirstHigher Percentage of used DRAM in Kbytes
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcKhiPerformanceDRamUsedFirstHigherAlertTime		1.3.6.1.4.1.2272.1.85.4.19
Timestamp of ciritcal percentage of used DRAM in Kbytes
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiPerformanceDRamUsedStatus		1.3.6.1.4.1.2272.1.85.4.20
Dynamic Random Access Memory Utilization Status
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiPerformanceSuspendedTaskStatus		1.3.6.1.4.1.2272.1.85.4.21
Suspended Tasks Status
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiPerformanceCPUControlFirstHigherAlertTime		1.3.6.1.4.1.2272.1.85.4.22
Timestamp of First Higher Alert for CPU Control
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiPerformanceCPUControlStatus		1.3.6.1.4.1.2272.1.85.4.23
CPU Control Status
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiPerformanceCurrentNoFBuf		1.3.6.1.4.1.2272.1.85.4.24
Current Number of None free buffer
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcKhiPerformanceFirstHigherNoFBuf		1.3.6.1.4.1.2272.1.85.4.25
FirstHigher Number of None free buffer
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcKhiPerformanceCurrentTxPacketsDropped		1.3.6.1.4.1.2272.1.85.4.26
Current Tx packet dropped
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcKhiPerformanceFirstHigherTxPacketsDropped		1.3.6.1.4.1.2272.1.85.4.27
FirstHigher Tx packet dropped
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcKhiPerformanceCurrentOutError		1.3.6.1.4.1.2272.1.85.4.28
Current Out errors
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcKhiPerformanceFirstHigherOutError		1.3.6.1.4.1.2272.1.85.4.29
FirstHigher Out errors
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcKhiPerformanceSuspendedTaskTable		1.3.6.1.4.1.2272.1.85.4.30
Suspended tasks table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcKhiPerformanceSuspendedTaskEntry

rcKhiPerformanceSuspendedTaskEntry		1.3.6.1.4.1.2272.1.85.4.30.1
Suspeded task table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcKhiPerformanceSuspendedTaskEntry

rcKhiPerformanceSuspendedTaskIndex		1.3.6.1.4.1.2272.1.85.4.30.1.1
An unique index used to identify a particular supended task index
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..100

rcKhiPerformanceSuspendedTaskId		1.3.6.1.4.1.2272.1.85.4.30.1.2
An unique task id of suspeded task
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiPerformanceSuspendedTaskName		1.3.6.1.4.1.2272.1.85.4.30.1.3
An unique task id of suspeded task
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

rcKhiPerformanceSuspendedTaskSuspendedTime		1.3.6.1.4.1.2272.1.85.4.30.1.4
Suspeded task time
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiPerformanceHistoryTable		1.3.6.1.4.1.2272.1.85.4.31
Performance History table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcKhiPerformanceHistoryEntry

rcKhiPerformanceHistoryEntry		1.3.6.1.4.1.2272.1.85.4.31.1
History Performance table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcKhiPerformanceHistoryEntry

rcKhiPerformanceHistoryIndex		1.3.6.1.4.1.2272.1.85.4.31.1.1
An unique index used to identify a particular performance history record
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..100

rcKhiPerformanceHistoryCpuUtil		1.3.6.1.4.1.2272.1.85.4.31.1.2
History record for CPU utilization
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcKhiPerformanceHistoryCpuUtilTimeStamp		1.3.6.1.4.1.2272.1.85.4.31.1.3
Timestamp of the historical cpu utilization
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiPerformanceHistorySwitchFabricUtil		1.3.6.1.4.1.2272.1.85.4.31.1.4
History Percentage of Switching Fabric utilization
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcKhiPerformanceHistorySwitchFabricUtilTimeStamp		1.3.6.1.4.1.2272.1.85.4.31.1.5
Timestamp of the historical switch fabric Utilization
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiPerformanceHistoryOtherSwitchFabricUtil		1.3.6.1.4.1.2272.1.85.4.31.1.6
History Percentage of Other Switching Fabric utilization
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcKhiPerformanceHistoryOtherSwitchFabricUtilTimeStamp		1.3.6.1.4.1.2272.1.85.4.31.1.7
Timestamp of the historical other switch fabric Utilization
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiPerformanceHistoryBufferUtil		1.3.6.1.4.1.2272.1.85.4.31.1.8
History Percentage of Buffer utilization
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcKhiPerformanceHistoryBufferUtilTimeStamp		1.3.6.1.4.1.2272.1.85.4.31.1.9
Timestamp of the historical Buffer Utilization
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiPerformanceHistoryDRamUsed		1.3.6.1.4.1.2272.1.85.4.31.1.10
History DRAM Used
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcKhiPerformanceHistoryDRamUsedTimeStamp		1.3.6.1.4.1.2272.1.85.4.31.1.11
Timestamp of the historical DRAM Used
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiPerformanceHistoryCPUControlTimeStamp		1.3.6.1.4.1.2272.1.85.4.31.1.12
Timestamp of the historical CPU Control
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiPerformanceHistoryNoFBuf		1.3.6.1.4.1.2272.1.85.4.31.1.13
History Number of None Free Buffer
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcKhiPerformanceHistoryTxPacketsDropped		1.3.6.1.4.1.2272.1.85.4.31.1.14
History Tx Packets Dropped
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcKhiPerformanceHistoryOutError		1.3.6.1.4.1.2272.1.85.4.31.1.15
History Out Errors
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcKhiPort		1.3.6.1.4.1.2272.1.85.5
OBJECT IDENTIFIER

rcKhiPortSystemStats		1.3.6.1.4.1.2272.1.85.5.1
OBJECT IDENTIFIER

rcKhiPortSystemStatsTotalUnicastRxPkts		1.3.6.1.4.1.2272.1.85.5.1.1
Total number of received Unicast packets within the past 2 minutes.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcKhiPortSystemStatsTotalUnicastTxPkts		1.3.6.1.4.1.2272.1.85.5.1.2
Total number of transmitted Unicast packets within the past 2 minutes.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcKhiPortSystemStatsUnicastPktsTxRxRatio		1.3.6.1.4.1.2272.1.85.5.1.3
Tx/Rx Ratio for Total Unicast Packets within the past 2 minutes.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiPortSystemStatsUnicastPktsTxRxRatioHealthStatus		1.3.6.1.4.1.2272.1.85.5.1.4
Health Indication for Unicast Packets Tx/Rx ratio. Green if the ratio is less than 5%. Yellow if it is between 5% and 50%. Red if it is greater than 50%.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiPortSystemStatsTotalMulticastRxPkts		1.3.6.1.4.1.2272.1.85.5.1.5
Total number of received Multicast packets within the past 2 minutes.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcKhiPortSystemStatsTotalMulticastTxPkts		1.3.6.1.4.1.2272.1.85.5.1.6
Total number of transmitted Multicast packets within the past 2 minutes.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcKhiPortSystemStatsTotalBroadcastRxPkts		1.3.6.1.4.1.2272.1.85.5.1.7
Total number of received Broadcast packets within the past 2 minutes.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcKhiPortSystemStatsTotalBroadcastTxPkts		1.3.6.1.4.1.2272.1.85.5.1.8
Total number of transmitted Broadcast packets within the past 2 minutes.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcKhiPortState		1.3.6.1.4.1.2272.1.85.5.2
OBJECT IDENTIFIER

rcKhiPortStateTotalPortsUp		1.3.6.1.4.1.2272.1.85.5.2.1
Total number of ports that are administratively enabled and operationally up.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiPortStatePortsUpList		1.3.6.1.4.1.2272.1.85.5.2.2
List of ports that are administratively enabled and operationally up.
Status: current	Access: read-only
OBJECT-TYPE
	PortSet

rcKhiPortStatePortsUpReferenceList		1.3.6.1.4.1.2272.1.85.5.2.3
Reference list of ports that are administratively enabled and operationally up.
Status: current	Access: read-only
OBJECT-TYPE
	PortSet

rcKhiPortStatePortsUpHealthStatus		1.3.6.1.4.1.2272.1.85.5.2.4
Health Indication for Ports Up list. When a clear operation is issued, rcKhiPortStatePortsUpList is copied into rcKhiPortStatePortsUpReferenceList and will be used as a reference to indicate health. From that point onwards, if rcKhiPortStatePortsUpList does not match rcKhiPortStatePortsUpReferenceList, the health would be indicated as Yellow. If it matches, it would be Green.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiPortStateTotalPortsDown		1.3.6.1.4.1.2272.1.85.5.2.5
Total number of ports that are administratively enabled and operationally down.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiPortStatePortsDownList		1.3.6.1.4.1.2272.1.85.5.2.6
List of ports that are administratively enabled and operationally down.
Status: current	Access: read-only
OBJECT-TYPE
	PortSet

rcKhiPortStateTotalSmltPortsUp		1.3.6.1.4.1.2272.1.85.5.2.7
Total number of SMLT ports that are administratively enabled and operationally up.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiPortStateSmltPortsUpList		1.3.6.1.4.1.2272.1.85.5.2.8
List of SMLT ports that are administratively enabled and operationally up.
Status: current	Access: read-only
OBJECT-TYPE
	PortSet

rcKhiPortStateSmltPortsUpReferenceList		1.3.6.1.4.1.2272.1.85.5.2.9
Reference list of SMLT ports that are administratively enabled and operationally up.
Status: current	Access: read-only
OBJECT-TYPE
	PortSet

rcKhiPortStateSmltPortsUpHealthStatus		1.3.6.1.4.1.2272.1.85.5.2.10
Health Indication for Ports Up list. When a clear operation is issued, rcKhiPortStateSmltPortsUpList is copied into rcKhiPortStateSmltPortsUpReferenceList and will be used as a reference to indicate health. From that point onwards, if rcKhiPortStatSmltePortsUpList does not match rcKhiPortStateSmltPortsUpReferenceList, the health would be indicated as Yellow. If it matches, it would be Green.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiPortStateTotalSmltPortsDown		1.3.6.1.4.1.2272.1.85.5.2.11
Total number of SMLT ports that are administratively enabled and operationally down.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiPortStateSmltPortsDownList		1.3.6.1.4.1.2272.1.85.5.2.12
List of SMLT ports that are administratively enabled and operationally down.
Status: current	Access: read-only
OBJECT-TYPE
	PortSet

rcKhiPortStateTotalIstPortsUp		1.3.6.1.4.1.2272.1.85.5.2.13
Total number of IST ports that are administratively enabled and operationally up.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiPortStateIstPortsUpList		1.3.6.1.4.1.2272.1.85.5.2.14
List of IST ports that are administratively enabled and operationally up.
Status: current	Access: read-only
OBJECT-TYPE
	PortSet

rcKhiPortStateIstPortsUpReferenceList		1.3.6.1.4.1.2272.1.85.5.2.15
Reference list of IST ports that are administratively enabled and operationally up.
Status: current	Access: read-only
OBJECT-TYPE
	PortSet

rcKhiPortStateIstPortsUpHealthStatus		1.3.6.1.4.1.2272.1.85.5.2.16
Health Indication for Ports Up list. When a clear operation is issued, rcKhiPortStateIstPortsUpList is copied into rcKhiPortStateIstPortsUpReferenceList and will be used as a reference to indicate health. From that point onwards, if rcKhiPortStateIstPortsUpList does not match rcKhiPortStateIstPortsUpReferenceList, the health would be indicated as Yellow. If it matches, it would be Green.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiPortStateTotalIstPortsDown		1.3.6.1.4.1.2272.1.85.5.2.17
Total number of IST ports that are administratively enabled and operationally down.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiPortStateIstPortsDownList		1.3.6.1.4.1.2272.1.85.5.2.18
List of IST ports that are administratively enabled and operationally down.
Status: current	Access: read-only
OBJECT-TYPE
	PortSet

rcKhiPortStateTotalPortUpEvents		1.3.6.1.4.1.2272.1.85.5.2.19
Total number of port up events.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiPortStatePortUpEventList		1.3.6.1.4.1.2272.1.85.5.2.20
List of ports that became operationally up.
Status: current	Access: read-only
OBJECT-TYPE
	PortSet

rcKhiPortStatePortUpEventsHealthStatus		1.3.6.1.4.1.2272.1.85.5.2.21
Port Up Events Health Indication.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiPortStatePortUpEventFirstEventTs		1.3.6.1.4.1.2272.1.85.5.2.22
Timestamp of the first occurence of a port up event after reboot or clear.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiPortStateTotalPortDownEvents		1.3.6.1.4.1.2272.1.85.5.2.23
Total number of port down events.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiPortStatePortDownEventList		1.3.6.1.4.1.2272.1.85.5.2.24
List of ports that became operationally down.
Status: current	Access: read-only
OBJECT-TYPE
	PortSet

rcKhiPortStatePortDownEventsHealthStatus		1.3.6.1.4.1.2272.1.85.5.2.25
Port Down Events Health Indication.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiPortStatePortDownEventFirstEventTs		1.3.6.1.4.1.2272.1.85.5.2.26
Timestamp of the first occurence of a port down event after reboot or clear.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiPortStateTotalSmltPortUpEvents		1.3.6.1.4.1.2272.1.85.5.2.27
Total number of SMLT port up events.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiPortStateSmltPortUpEventList		1.3.6.1.4.1.2272.1.85.5.2.28
List of SMLT ports that became operationally up.
Status: current	Access: read-only
OBJECT-TYPE
	PortSet

rcKhiPortStateSmltPortUpEventsHealthStatus		1.3.6.1.4.1.2272.1.85.5.2.29
SMLT Port Up Events Health Indication.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiPortStateSmltPortUpEventFirstEventTs		1.3.6.1.4.1.2272.1.85.5.2.30
Timestamp of the first occurence of a SMLT port up event after reboot or clear.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiPortStateTotalSmltPortDownEvents		1.3.6.1.4.1.2272.1.85.5.2.31
Total number of SMLT port down events.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiPortStateSmltPortDownEventList		1.3.6.1.4.1.2272.1.85.5.2.32
List of SMLT ports that became operationally down.
Status: current	Access: read-only
OBJECT-TYPE
	PortSet

rcKhiPortStateSmltPortDownEventsHealthStatus		1.3.6.1.4.1.2272.1.85.5.2.33
SMLT Port Down Events Health Indication.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiPortStateSmltPortDownEventFirstEventTs		1.3.6.1.4.1.2272.1.85.5.2.34
Timestamp of the first occurence of an SMLT port down event after reboot or clear.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiPortStateTotalIstPortUpEvents		1.3.6.1.4.1.2272.1.85.5.2.35
Total number of SMLT port up events.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiPortStateIstPortUpEventList		1.3.6.1.4.1.2272.1.85.5.2.36
List of SMLT ports that became operationally up.
Status: current	Access: read-only
OBJECT-TYPE
	PortSet

rcKhiPortStateIstPortUpEventsHealthStatus		1.3.6.1.4.1.2272.1.85.5.2.37
IST Port Up Events Health Indication.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiPortStateIstPortUpEventFirstEventTs		1.3.6.1.4.1.2272.1.85.5.2.38
Timestamp of the first occurence of a IST port up event after reboot or clear.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiPortStateTotalIstPortDownEvents		1.3.6.1.4.1.2272.1.85.5.2.39
Total number of SMLT port down events.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiPortStateIstPortDownEventList		1.3.6.1.4.1.2272.1.85.5.2.40
List of SMLT ports that became operationally down.
Status: current	Access: read-only
OBJECT-TYPE
	PortSet

rcKhiPortStateIstPortDownEventsHealthStatus		1.3.6.1.4.1.2272.1.85.5.2.41
IST Port Down Events Health Indication.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiPortStateIstPortDownEventFirstEventTs		1.3.6.1.4.1.2272.1.85.5.2.42
Timestamp of the first occurence of an IST port down event after reboot or clear.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiPortStateEventsHistoryTable		1.3.6.1.4.1.2272.1.85.5.2.43
Port State Events Historical Data.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcKhiPortStateEventsHistoryEntry

rcKhiPortStateEventsHistoryEntry		1.3.6.1.4.1.2272.1.85.5.2.43.1
Port State Events history table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcKhiPortStateEventsHistoryEntry

rcKhiPortStateEventsHistoryIndex		1.3.6.1.4.1.2272.1.85.5.2.43.1.1
Historical data index number.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..10

rcKhiPortStateEventsHistoryTimestamp		1.3.6.1.4.1.2272.1.85.5.2.43.1.2
Timestamp indicating when the event occurred.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiPortStateEventsHistoryPort		1.3.6.1.4.1.2272.1.85.5.2.43.1.3
Port number where the event occurred.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..2147483647

rcKhiPortStateEventsHistoryEvent		1.3.6.1.4.1.2272.1.85.5.2.43.1.4
Indication about the event-type.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	portUp(1), portDown(2), smltPortUp(3), smltPortDown(4), istPortUp(5), istPortDown(6), ucastPktTxRxRatioYellow(7), ucastPktTxRxRatioRed(8)

rcKhiPortErrors		1.3.6.1.4.1.2272.1.85.5.3
OBJECT IDENTIFIER

rcKhiPortErrorsEventsTable		1.3.6.1.4.1.2272.1.85.5.3.1
Port Error Events Data.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcKhiPortErrorsEventsEntry

rcKhiPortErrorsEventsEntry		1.3.6.1.4.1.2272.1.85.5.3.1.1
Port error events table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcKhiPortErrorsEventsEntry

rcKhiPortErrorsEventsPortNum		1.3.6.1.4.1.2272.1.85.5.3.1.1.1
Port number where the event occurred.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..2147483647

rcKhiPortErrorsEventsSingleCollisionErr		1.3.6.1.4.1.2272.1.85.5.3.1.1.2
Health Indication for Single Collisions errors on the port.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiPortErrorsEventsMultipleCollisionErr		1.3.6.1.4.1.2272.1.85.5.3.1.1.3
Health Indication for Multiple Collisions errors on the port.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiPortErrorsEventsLateCollisionErr		1.3.6.1.4.1.2272.1.85.5.3.1.1.4
Health Indication for Late Collisions errors on the port.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiPortErrorsEventsExcessiveCollisionErr		1.3.6.1.4.1.2272.1.85.5.3.1.1.5
Health Indication for Excessive Collisions errors on the port.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiPortErrorsEventsMacRxErr		1.3.6.1.4.1.2272.1.85.5.3.1.1.6
Health Indication for Mac Rx errors on the port.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiPortErrorsEventsMacTxErr		1.3.6.1.4.1.2272.1.85.5.3.1.1.7
Health Indication for Mac Tx errors on the port.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiPortErrorsEventsDeferTxErr		1.3.6.1.4.1.2272.1.85.5.3.1.1.8
Health Indication for Defer Tx errors on the port.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiPortErrorsEventsPacketErr		1.3.6.1.4.1.2272.1.85.5.3.1.1.9
Health Indication for Packet errors on the port.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiPortErrorsEventsLinkInactiveErr		1.3.6.1.4.1.2272.1.85.5.3.1.1.10
Health Indication for Link Inactive errors on the port.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiPortErrorsEventsUnknownProtoErr		1.3.6.1.4.1.2272.1.85.5.3.1.1.11
Health Indication for Unknown Proto errors on the port.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiPortErrorsEventsInFlwctrlErr		1.3.6.1.4.1.2272.1.85.5.3.1.1.12
Health Indication for In Flwctrl errors on the port.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiPortErrorsEventsOutFlwctrlErr		1.3.6.1.4.1.2272.1.85.5.3.1.1.13
Health Indication for Out Flwctrl errors on the port.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiPortErrorsEventsAlignErr		1.3.6.1.4.1.2272.1.85.5.3.1.1.14
Health Indication for Align errors on the port.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiPortErrorsEventsFCSErr		1.3.6.1.4.1.2272.1.85.5.3.1.1.15
Health Indication for FCS errors on the port.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiPortErrorsEventsFramesLongErr		1.3.6.1.4.1.2272.1.85.5.3.1.1.16
Health Indication for Frames Long errors on the port.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiPortErrorsEventsTooShortErr		1.3.6.1.4.1.2272.1.85.5.3.1.1.17
Health Indication for Too Short errors on the port.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiPortErrorsEventsLinkFailureErr		1.3.6.1.4.1.2272.1.85.5.3.1.1.18
Health Indication for Link Failure errors on the port.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiPortErrorsEventsCarrierSenseErr		1.3.6.1.4.1.2272.1.85.5.3.1.1.19
Health Indication for Carrier Sense errors on the port.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiPortErrorsEventsCarrierErr		1.3.6.1.4.1.2272.1.85.5.3.1.1.20
Health Indication for Carrier errors on the port.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiPortErrorsEventsSQETestErr		1.3.6.1.4.1.2272.1.85.5.3.1.1.21
Health Indication for SQE Test errors on the port.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiPortErrorsHistoryTable		1.3.6.1.4.1.2272.1.85.5.3.2
Port Errors Historical Data.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcKhiPortErrorsHistoryEntry

rcKhiPortErrorsHistoryEntry		1.3.6.1.4.1.2272.1.85.5.3.2.1
Port errors history table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcKhiPortErrorsHistoryEntry

rcKhiPortErrorsHistoryIndex		1.3.6.1.4.1.2272.1.85.5.3.2.1.1
Index number.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..10

rcKhiPortErrorsHistoryTimestamp		1.3.6.1.4.1.2272.1.85.5.3.2.1.2
Timestamp indicating when the event occurred.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiPortErrorsHistoryPort		1.3.6.1.4.1.2272.1.85.5.3.2.1.3
Port number where the event occurred.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..2147483647

rcKhiPortErrorsHistoryErrorEvents		1.3.6.1.4.1.2272.1.85.5.3.2.1.4
This is used to specify the port error information. bit 0 - Single Collision Errors bit 1 - Multiple Collision Errors bit 2 - Late Collision Errors bit 3 - Excessive Collision Errors bit 4 - Mac Rx Errors bit 5 - Mac Tx Errors bit 6 - Defer Tx Errors bit 7 - Packet Errors bit 8 - Link Inactive Errors bit 9 - Unknown Proto Errors bit 10 - In Flwctrl Errors bit 11 - Out Flwctrl Errors bit 12 - Align Errors bit 13 - FCS Errors bit 14 - Frames Long Errors bit 15 - Too Short Errors bit 16 - Link Failure Errors bit 17 - Carrier Sense Errors bit 18 - Carrier Errors bit 19 - SQE Test Errors
Status: current	Access: read-only
OBJECT-TYPE
	BITS	singleCollisionErrors(0), multipleCollisionErrors(1), lateCollisionErrors(2), excessiveCollisionErrors(3), macRxErrors(4), macTxErrors(5), deferTxErrors(6), packetErrors(7), linkInactiveErrors(8), unknownProtoErrors(9), inFlwctrlErrors(10), outFlwctrlErrors(11), alignErrors(12), fcsErrors(13), framesLongErrors(14), tooShortErrors(15), linkFailureErrors(16), carrierSenseErrors(17), carrierErrors(18), sqeTestErrors(19)

rcKhiForwarding		1.3.6.1.4.1.2272.1.85.6
OBJECT IDENTIFIER

rcKhiForwardingAsicHealthTable		1.3.6.1.4.1.2272.1.85.6.1
Forwarding Asic Key Health Indicator MIB.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcKhiForwardingAsicHealthEntry

rcKhiForwardingAsicHealthEntry		1.3.6.1.4.1.2272.1.85.6.1.1
Forwarding KHI - Asic Health table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcKhiForwardingAsicHealthEntry

rcKhiForwardingAsicHealthSlotNumber		1.3.6.1.4.1.2272.1.85.6.1.1.1
Slot Number.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..10

rcKhiForwardingAsicHealthLeftLnIngBkPrsureRstCnt		1.3.6.1.4.1.2272.1.85.6.1.1.2
Total number of Left Lane Ingress RSP Combined Back Pressure Resets.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiForwardingAsicHealthMidLnIngBkPrsureRstCnt		1.3.6.1.4.1.2272.1.85.6.1.1.3
Total number of Middle Lane Ingress RSP Combined Back Pressure Resets.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiForwardingAsicHealthRightLnIngBkPrsureRstCnt		1.3.6.1.4.1.2272.1.85.6.1.1.4
Total number of Right Lane Ingress RSP Combined Back Pressure Resets.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiForwardingAsicHealthLeftLnIngBkPrsureRstStatus		1.3.6.1.4.1.2272.1.85.6.1.1.5
Left Lane Ingress RSP Back Pressure Resets Health Indication. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Red.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingAsicHealthMidLnIngBkPrsureRstStatus		1.3.6.1.4.1.2272.1.85.6.1.1.6
Middle Lane ngress RSP Back Pressure Resets Health Indication. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Red.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingAsicHealthRightLnIngBkPrsureRstStatus		1.3.6.1.4.1.2272.1.85.6.1.1.7
Right Lane Ingress RSP Back Pressure Resets Health Indication. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Red.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingAsicHealthLeftLnIngSPIProtoRstCnt		1.3.6.1.4.1.2272.1.85.6.1.1.8
Total number of Left Lane Ingress RSP SPI Protocol Resets.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiForwardingAsicHealthMidLnIngSPIProtoRstCnt		1.3.6.1.4.1.2272.1.85.6.1.1.9
Total number of Middle Lane Ingress RSP SPI Protocol Resets.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiForwardingAsicHealthRightLnIngSPIProtoRstCnt		1.3.6.1.4.1.2272.1.85.6.1.1.10
Total number of Right Lane Ingress RSP SPI Protocol Resets.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiForwardingAsicHealthLeftLnIngSPIProtoRstStatus		1.3.6.1.4.1.2272.1.85.6.1.1.11
Left Lane Ingress RSP SPI Protocol Resets Health Indication. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Red.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingAsicHealthMidLnIngSPIProtoRstStatus		1.3.6.1.4.1.2272.1.85.6.1.1.12
Middle Lane Ingress RSP SPI Protocol Resets Health Indication. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Red.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingAsicHealthRightLnIngSPIProtoRstStatus		1.3.6.1.4.1.2272.1.85.6.1.1.13
Right Lane Ingress RSP SPI Protocol Resets Health Indication. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Red.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingAsicHealthLeftLnIngSPIDefragCnt		1.3.6.1.4.1.2272.1.85.6.1.1.14
Total number of Left Lane Ingress RSP SPI Defrag Resets.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiForwardingAsicHealthMidLnIngSPIDefragCnt		1.3.6.1.4.1.2272.1.85.6.1.1.15
Total number of Middle Lane Ingress RSP SPI Defrag Resets.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiForwardingAsicHealthRightLnIngSPIDefragCnt		1.3.6.1.4.1.2272.1.85.6.1.1.16
Total number of Right Lane Ingress RSP SPI Defrag Resets.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiForwardingAsicHealthLeftLnIngSPIDefragStatus		1.3.6.1.4.1.2272.1.85.6.1.1.17
Left Lane Ingress RSP SPI Defrag Health Indication. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Red.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingAsicHealthMidLnIngSPIDefragStatus		1.3.6.1.4.1.2272.1.85.6.1.1.18
Middle Lane Ingress RSP SPI Defrag Health Indication. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Red.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingAsicHealthRightLnIngSPIDefragStatus		1.3.6.1.4.1.2272.1.85.6.1.1.19
Right Lane Ingress RSP SPI Defrag Health Indication. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Red.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingAsicHealthLeftLnEgrMcastQFullRstCnt		1.3.6.1.4.1.2272.1.85.6.1.1.20
Total number of Left Lane Egress RSP Multicast Queue Full Resets.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiForwardingAsicHealthMidLnEgrMcastQFullRstCnt		1.3.6.1.4.1.2272.1.85.6.1.1.21
Total number of Middle Lane Egress RSP Multicast Queue Full Resets.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiForwardingAsicHealthRightLnEgrMcastQFullRstCnt		1.3.6.1.4.1.2272.1.85.6.1.1.22
Total number of Right Lane Egress RSP Multicast Queue Full Resets.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiForwardingAsicHealthLeftLnEgrMcastQFullRstStatus		1.3.6.1.4.1.2272.1.85.6.1.1.23
Left Lane Egress RSP Multicast Queue Full Resets Health Indication. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Red.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingAsicHealthMidLnEgrMcastQFullRstStatus		1.3.6.1.4.1.2272.1.85.6.1.1.24
Middle Lane Egress RSP Multicast Queue Full Resets Health Indication. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Red.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingAsicHealthRightLnEgrMcastQFullRstStatus		1.3.6.1.4.1.2272.1.85.6.1.1.25
Right Lane Egress RSP Multicast Queue Full Resets Health Indication. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Red.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingAsicHealthLeftLnEgrFreePgErrRstCnt		1.3.6.1.4.1.2272.1.85.6.1.1.26
Total number of Left Lane Egress RSP Free Page Error Resets.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiForwardingAsicHealthMidLnEgrFreePgErrRstCnt		1.3.6.1.4.1.2272.1.85.6.1.1.27
Total number of Middle Lane Egress RSP Free Page Error Resets.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiForwardingAsicHealthRightLnEgrFreePgErrRstCnt		1.3.6.1.4.1.2272.1.85.6.1.1.28
Total number of Right Lane Egress RSP Free Page Error Resets.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiForwardingAsicHealthLeftLnEgrFreePgErrRstStatus		1.3.6.1.4.1.2272.1.85.6.1.1.29
Left Lane Egress RSP Free Page Error Resets Health Indication. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Red.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingAsicHealthMidLnEgrFreePgErrRstStatus		1.3.6.1.4.1.2272.1.85.6.1.1.30
Middle Lane Egress RSP Free Page Error Resets Health Indication. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Red.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingAsicHealthRightLnEgrFreePgErrRstStatus		1.3.6.1.4.1.2272.1.85.6.1.1.31
Left Lane Egress RSP Free Page Error Resets Health Indication. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Red.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingAsicHealthLeftLnEgrUcastQFullRstCnt		1.3.6.1.4.1.2272.1.85.6.1.1.32
Total number of Left Lane Egress RSP Unicast Queue Full Resets.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiForwardingAsicHealthMidLnEgrUcastQFullRstCnt		1.3.6.1.4.1.2272.1.85.6.1.1.33
Total number of Middle Lane Egress RSP Unicast Queue Full Resets.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiForwardingAsicHealthRightLnEgrUcastQFullRstCnt		1.3.6.1.4.1.2272.1.85.6.1.1.34
Total number of Right Lane Egress RSP Unicast Queue Full Resets.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiForwardingAsicHealthLeftLnEgrUcastQFullRstStatus		1.3.6.1.4.1.2272.1.85.6.1.1.35
Left Lane Egress RSP Unicast Queue Full Resets Health Indication. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Red.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingAsicHealthMidLnEgrUcastQFullRstStatus		1.3.6.1.4.1.2272.1.85.6.1.1.36
Middle Lane Egress RSP Unicast Queue Full Resets Health Indication. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Red.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingAsicHealthRightLnEgrUcastQFullRstStatus		1.3.6.1.4.1.2272.1.85.6.1.1.37
Right Lane Egress RSP Unicast Queue Full Resets Health Indication. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Red.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingAsicHealthLeftLnEgrFreePgLwrLmtRstCnt		1.3.6.1.4.1.2272.1.85.6.1.1.39
Total number of Left Lane Egress RSP Free Pages at Lower Limit Resets.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiForwardingAsicHealthMidLnEgrFreePgLwrLmtRstCnt		1.3.6.1.4.1.2272.1.85.6.1.1.40
Total number of Middle Lane Egress RSP Free Pages at Lower Limit Resets.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiForwardingAsicHealthRightLnEgrFreePgLwrLmtRstCnt		1.3.6.1.4.1.2272.1.85.6.1.1.41
Total number of Right Lane Egress RSP Free Pages at Lower Limit Resets.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiForwardingAsicHealthLeftLnEgrFreePgLwrLmtStatus		1.3.6.1.4.1.2272.1.85.6.1.1.42
Left Lane Egress RSP Free Pages at Lower Limit Resets Health Indication. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Red.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingAsicHealthMidLnEgrFreePgLwrLmtStatus		1.3.6.1.4.1.2272.1.85.6.1.1.43
Middle Lane Egress RSP Free Pages at Lower Limit Resets Health Indication. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Red.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingAsicHealthRightLnEgrFreePgLwrLmtStatus		1.3.6.1.4.1.2272.1.85.6.1.1.44
Right Lane Egress RSP Free Pages at Lower Limit Resets Health Indication. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Red.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingAsicHealthLeftLnEgrRepIDMismatchRstCnt		1.3.6.1.4.1.2272.1.85.6.1.1.45
Total number of Left Lane Egress RSP Replication ID Mismatch Resets.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiForwardingAsicHealthMidLnEgrRepIDMismatchRstCnt		1.3.6.1.4.1.2272.1.85.6.1.1.46
Total number of Middle Lane Egress RSP Replication ID Mismatch Resets.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiForwardingAsicHealthRightLnEgrRepIDMismatchRstCnt		1.3.6.1.4.1.2272.1.85.6.1.1.47
Total number of Right Lane Egress RSP Replication ID Mismatch Resets.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiForwardingAsicHealthLeftLnEgrRepIDMismatchStatus		1.3.6.1.4.1.2272.1.85.6.1.1.48
Left Lane Egress RSP Replication ID Mismatch Resets Health Indication. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Red.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingAsicHealthMidLnEgrRepIDMismatchStatus		1.3.6.1.4.1.2272.1.85.6.1.1.49
Middle Lane Egress RSP Replication ID Mismatch Resets Health Indication. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Red.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingAsicHealthRightLnEgrRepIDMismatchStatus		1.3.6.1.4.1.2272.1.85.6.1.1.50
Right Lane Egress RSP Replication ID Mismatch Resets Health Indication. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Red.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingAsicHealthLeftLnEgrNoBeepBeepRstCnt		1.3.6.1.4.1.2272.1.85.6.1.1.51
Total number of Left Lane Egress RSP No Beep-Beep Resets.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiForwardingAsicHealthMidLnEgrNoBeepBeepRstCnt		1.3.6.1.4.1.2272.1.85.6.1.1.52
Total number of Middle Lane Egress RSP No Beep-Beep Resets.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiForwardingAsicHealthRightLnEgrNoBeepBeepRstCnt		1.3.6.1.4.1.2272.1.85.6.1.1.53
Total number of Right Lane Egress RSP No Beep-Beep Resets.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiForwardingAsicHealthLeftLnEgrNoBeepBeepStatus		1.3.6.1.4.1.2272.1.85.6.1.1.54
Left Lane Egress RSP No Beep-Beep Resets Health Indication. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Red.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingAsicHealthMidLnEgrNoBeepBeepStatus		1.3.6.1.4.1.2272.1.85.6.1.1.55
Middle Lane Egress RSP No Beep-Beep Resets Health Indication. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Red.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingAsicHealthRightLnEgrNoBeepBeepStatus		1.3.6.1.4.1.2272.1.85.6.1.1.56
Right Lane Egress RSP No Beep-Beep Resets Health Indication. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Red.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingRSPStateTable		1.3.6.1.4.1.2272.1.85.6.2
Forwarding Key Health Indicator MIB - RSP Stats.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcKhiForwardingRSPStateEntry

rcKhiForwardingRSPStateEntry		1.3.6.1.4.1.2272.1.85.6.2.1
Forwarding KHI - RSP State table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcKhiForwardingRSPStateEntry

rcKhiForwardingRSPStateSlotNumber		1.3.6.1.4.1.2272.1.85.6.2.1.1
Slot Number.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..10

rcKhiForwardingRSPStateDirection		1.3.6.1.4.1.2272.1.85.6.2.1.2
Direction - Ingress or Egress.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	ingress(1), egress(2)

rcKhiForwardingRSPStateLeftLnErrMask		1.3.6.1.4.1.2272.1.85.6.2.1.3
Left Lane RSP State Error Bit Mask. Each bit in the mask represents a specific error. Bit 0 - CIF Parity Error. Bit 1 - CIF Protocol Error. Bit 2 - EME0 Parity Error. Bit 3 - EME1 Parity Error. Bit 4 - BAP Host Read Error. Bit 5 - BAP Host Write Error. Bit 6 - BAP Clock PLL is not locked. Bit 7 - BAP Tx Clock PLL is not locked. Bit 8 - BAP Memory Clock PLL is not locked. Bit 9 - GAB Error. Bit 10 - BAP Intf Timeout. Bit 11 - BAP Intf Error. Bit 12 - BAP Decoder Error. Bit 13 - BAP Decoder Special Access Error. Bit 14 - BAP Controller Write Error. Bit 15 - BAP Controller Read Error. Bit 16 - BAP GAB Error. Bit 17 - IME0 is disabled. Bit 18 - IME1 is disabled. Bit 19 - Hash engine is disabled. Bit 20 - Multiplication Engine is disabled. Bit 21 - FDIB Empty Pkt. Wrong PTM access. Bit 22 - FDIB Past End of Pkt Error. Bit 23 - FDIB Fifo empty. Wrong PM access. Bit 24 - FDIB Invalid Page. Bit 25 - Fifo Full. Bit 26 - FDIB Mixed access. Bit 27 - FDOB PM Error. Bit 28 - FDOB is Full. Bit 29 - FDOB is empty. Bit 30 - PTM Bus Error. Bit 31 - PM Program Counter Error. Bit 32 - PM Stats BUS Error. Bit 33 - PM FDIB HPI BUS Error. Bit 34 - PM EME1 Parity Error. Bit 35 - PM EME0 Parity Error. Bit 36 - PM Multicast Error. Bit 37 - PM Frame Error. Bit 38 - PM Pop rollover. Bit 39 - PM Release Error. Bit 40 - AM Unsupported optype for region/device exception. Bit 41 - AM Illegal region/subregion exception. Bit 42 - AM Search run on exception. Bit 43 - AM Search bus error exception. Bit 44 - AM Parity error exception. Bit 45 - AM Protocol error exception. Bit 46 - AM Illegal Argument exception. Bit 47 - AM Non-alligned address exception. Bit 48 - AM Packet memory bus error exception. Bit 49 - AM Packet header address error exception. Bit 50 - AM Lookup Continue Zero exception. Bit 51 - AM Unsupported RSVD8 exception. Bit 52 - AM Unsupported RSVD10 exception. Bit 53 - AM Unsupported RSVD1 exception. Bit 54 - AM Unsupported RSVD2 exception. Bit 55 - AM Unsupported RSVD3 exception. Bit 56 - AM Unsupported RSVD4 exception. Bit 57 - AM Unsupported RSVD5 exception. Bit 58 - AM Unsupported Unknown h/w failure exception. Bit 59 - AM Software Interrupt. Bit 60 - Missing RSP Heartbeats.
Status: current	Access: read-only
OBJECT-TYPE
	BITS	cifParityError(0), cifProtocolError(1), eme0ParityError(2), eme1ParityError(3), bapHostReadError(4), bapHostWriteError(5), bapClockPLLNotLocked(6), bapTxClockPLLNotLocked(7), bapMemoryClockPLLNotLocked(8), gabError(9), bapIntfTimeout(10), bapIntfError(11), bapDecoderError(12), bapDecoderSpecialAccessError(13), bapControllerWriteError(14), bapControllerReadError(15), bapGABError(16), ime0Disabled(17), ime1Disabled(18), hashEngineDisabled(19), multiplicationEngineDisabled(20), fdibEmptyPktWrongPTMAccess(21), fdibPastEndOfPktError(22), fdibFifoEmptyWrongPMAccess(23), fdibInvalidPage(24), fifoFull(25), fdibMixedAccess(26), fdobPMError(27), fdobIsFull(28), fdobIsEmpty(29), ptmBusError(30), pmProgramCounterError(31), pmStatsBUSError(32), pmFDIBHPIBUSError(33), pmEME1ParityError(34), pmEME0ParityError(35), pmMulticastError(36), pmFrameError(37), pmPopRollover(38), pmReleaseError(39), amUnsupportedOptypeForRegionOrDeviceException(40), amIllegalRegionOrSubregionException(41), amSearchRunOnException(42), amSearchBusErrorException(43), amParityErrorException(44), amProtocolErrorException(45), amIllegalArgumentException(46), amNonAllignedAddressException(47), amPacketMemoryBusErrorException(48), amPacketHeaderAddressErrorException(49), amLookupContinueZeroException(50), amUnsupportedRSVD8Exception(51), amUnsupportedRSVD10Exception(52), amUnsupportedRSVD1Exception(53), amUnsupportedRSVD2Exception(54), amUnsupportedRSVD3Exception(55), amUnsupportedRSVD4Exception(56), amUnsupportedRSVD5Exception(57), amUnsupportedUnknownHWFailureException(58), amSoftwareInterrupt(59), missingRSPHeartbeats(60)

rcKhiForwardingRSPStateMidLnErrMask		1.3.6.1.4.1.2272.1.85.6.2.1.4
Middle Lane RSP State Error Bit Mask. Each bit in the mask represents a specific error. Bit 0 - CIF Parity Error. Bit 1 - CIF Protocol Error. Bit 2 - EME0 Parity Error. Bit 3 - EME1 Parity Error. Bit 4 - BAP Host Read Error. Bit 5 - BAP Host Write Error. Bit 6 - BAP Clock PLL is not locked. Bit 7 - BAP Tx Clock PLL is not locked. Bit 8 - BAP Memory Clock PLL is not locked. Bit 9 - GAB Error. Bit 10 - BAP Intf Timeout. Bit 11 - BAP Intf Error. Bit 12 - BAP Decoder Error. Bit 13 - BAP Decoder Special Access Error. Bit 14 - BAP Controller Write Error. Bit 15 - BAP Controller Read Error. Bit 16 - BAP GAB Error. Bit 17 - IME0 is disabled. Bit 18 - IME1 is disabled. Bit 19 - Hash engine is disabled. Bit 20 - Multiplication Engine is disabled. Bit 21 - FDIB Empty Pkt. Wrong PTM access. Bit 22 - FDIB Past End of Pkt Error. Bit 23 - FDIB Fifo empty. Wrong PM access. Bit 24 - FDIB Invalid Page. Bit 25 - Fifo Full. Bit 26 - FDIB Mixed access. Bit 27 - FDOB PM Error. Bit 28 - FDOB is Full. Bit 29 - FDOB is empty. Bit 30 - PTM Bus Error. Bit 31 - PM Program Counter Error. Bit 32 - PM Stats BUS Error. Bit 33 - PM FDIB HPI BUS Error. Bit 34 - PM EME1 Parity Error. Bit 35 - PM EME0 Parity Error. Bit 36 - PM Multicast Error. Bit 37 - PM Frame Error. Bit 38 - PM Pop rollover. Bit 39 - PM Release Error. Bit 40 - AM Unsupported optype for region/device exception. Bit 41 - AM Illegal region/subregion exception. Bit 42 - AM Search run on exception. Bit 43 - AM Search bus error exception. Bit 44 - AM Parity error exception. Bit 45 - AM Protocol error exception. Bit 46 - AM Illegal Argument exception. Bit 47 - AM Non-alligned address exception. Bit 48 - AM Packet memory bus error exception. Bit 49 - AM Packet header address error exception. Bit 50 - AM Lookup Continue Zero exception. Bit 51 - AM Unsupported RSVD8 exception. Bit 52 - AM Unsupported RSVD10 exception. Bit 53 - AM Unsupported RSVD1 exception. Bit 54 - AM Unsupported RSVD2 exception. Bit 55 - AM Unsupported RSVD3 exception. Bit 56 - AM Unsupported RSVD4 exception. Bit 57 - AM Unsupported RSVD5 exception. Bit 58 - AM Unsupported Unknown h/w failure exception. Bit 59 - AM Software Interrupt. Bit 60 - Missing RSP Heartbeats.
Status: current	Access: read-only
OBJECT-TYPE
	BITS	cifParityError(0), cifProtocolError(1), eme0ParityError(2), eme1ParityError(3), bapHostReadError(4), bapHostWriteError(5), bapClockPLLNotLocked(6), bapTxClockPLLNotLocked(7), bapMemoryClockPLLNotLocked(8), gabError(9), bapIntfTimeout(10), bapIntfError(11), bapDecoderError(12), bapDecoderSpecialAccessError(13), bapControllerWriteError(14), bapControllerReadError(15), bapGABError(16), ime0Disabled(17), ime1Disabled(18), hashEngineDisabled(19), multiplicationEngineDisabled(20), fdibEmptyPktWrongPTMAccess(21), fdibPastEndOfPktError(22), fdibFifoEmptyWrongPMAccess(23), fdibInvalidPage(24), fifoFull(25), fdibMixedAccess(26), fdobPMError(27), fdobIsFull(28), fdobIsEmpty(29), ptmBusError(30), pmProgramCounterError(31), pmStatsBUSError(32), pmFDIBHPIBUSError(33), pmEME1ParityError(34), pmEME0ParityError(35), pmMulticastError(36), pmFrameError(37), pmPopRollover(38), pmReleaseError(39), amUnsupportedOptypeForRegionOrDeviceException(40), amIllegalRegionOrSubregionException(41), amSearchRunOnException(42), amSearchBusErrorException(43), amParityErrorException(44), amProtocolErrorException(45), amIllegalArgumentException(46), amNonAllignedAddressException(47), amPacketMemoryBusErrorException(48), amPacketHeaderAddressErrorException(49), amLookupContinueZeroException(50), amUnsupportedRSVD8Exception(51), amUnsupportedRSVD10Exception(52), amUnsupportedRSVD1Exception(53), amUnsupportedRSVD2Exception(54), amUnsupportedRSVD3Exception(55), amUnsupportedRSVD4Exception(56), amUnsupportedRSVD5Exception(57), amUnsupportedUnknownHWFailureException(58), amSoftwareInterrupt(59), missingRSPHeartbeats(60)

rcKhiForwardingRSPStateRightLnErrMask		1.3.6.1.4.1.2272.1.85.6.2.1.5
Right Lane RSP State Error Bit Mask. Each bit in the mask represents a specific error. Bit 0 - CIF Parity Error. Bit 1 - CIF Protocol Error. Bit 2 - EME0 Parity Error. Bit 3 - EME1 Parity Error. Bit 4 - BAP Host Read Error. Bit 5 - BAP Host Write Error. Bit 6 - BAP Clock PLL is not locked. Bit 7 - BAP Tx Clock PLL is not locked. Bit 8 - BAP Memory Clock PLL is not locked. Bit 9 - GAB Error. Bit 10 - BAP Intf Timeout. Bit 11 - BAP Intf Error. Bit 12 - BAP Decoder Error. Bit 13 - BAP Decoder Special Access Error. Bit 14 - BAP Controller Write Error. Bit 15 - BAP Controller Read Error. Bit 16 - BAP GAB Error. Bit 17 - IME0 is disabled. Bit 18 - IME1 is disabled. Bit 19 - Hash engine is disabled. Bit 20 - Multiplication Engine is disabled. Bit 21 - FDIB Empty Pkt. Wrong PTM access. Bit 22 - FDIB Past End of Pkt Error. Bit 23 - FDIB Fifo empty. Wrong PM access. Bit 24 - FDIB Invalid Page. Bit 25 - Fifo Full. Bit 26 - FDIB Mixed access. Bit 27 - FDOB PM Error. Bit 28 - FDOB is Full. Bit 29 - FDOB is empty. Bit 30 - PTM Bus Error. Bit 31 - PM Program Counter Error. Bit 32 - PM Stats BUS Error. Bit 33 - PM FDIB HPI BUS Error. Bit 34 - PM EME1 Parity Error. Bit 35 - PM EME0 Parity Error. Bit 36 - PM Multicast Error. Bit 37 - PM Frame Error. Bit 38 - PM Pop rollover. Bit 39 - PM Release Error. Bit 40 - AM Unsupported optype for region/device exception. Bit 41 - AM Illegal region/subregion exception. Bit 42 - AM Search run on exception. Bit 43 - AM Search bus error exception. Bit 44 - AM Parity error exception. Bit 45 - AM Protocol error exception. Bit 46 - AM Illegal Argument exception. Bit 47 - AM Non-alligned address exception. Bit 48 - AM Packet memory bus error exception. Bit 49 - AM Packet header address error exception. Bit 50 - AM Lookup Continue Zero exception. Bit 51 - AM Unsupported RSVD8 exception. Bit 52 - AM Unsupported RSVD10 exception. Bit 53 - AM Unsupported RSVD1 exception. Bit 54 - AM Unsupported RSVD2 exception. Bit 55 - AM Unsupported RSVD3 exception. Bit 56 - AM Unsupported RSVD4 exception. Bit 57 - AM Unsupported RSVD5 exception. Bit 58 - AM Unsupported Unknown h/w failure exception. Bit 59 - AM Software Interrupt. Bit 60 - Missing RSP Heartbeats.
Status: current	Access: read-only
OBJECT-TYPE
	BITS	cifParityError(0), cifProtocolError(1), eme0ParityError(2), eme1ParityError(3), bapHostReadError(4), bapHostWriteError(5), bapClockPLLNotLocked(6), bapTxClockPLLNotLocked(7), bapMemoryClockPLLNotLocked(8), gabError(9), bapIntfTimeout(10), bapIntfError(11), bapDecoderError(12), bapDecoderSpecialAccessError(13), bapControllerWriteError(14), bapControllerReadError(15), bapGABError(16), ime0Disabled(17), ime1Disabled(18), hashEngineDisabled(19), multiplicationEngineDisabled(20), fdibEmptyPktWrongPTMAccess(21), fdibPastEndOfPktError(22), fdibFifoEmptyWrongPMAccess(23), fdibInvalidPage(24), fifoFull(25), fdibMixedAccess(26), fdobPMError(27), fdobIsFull(28), fdobIsEmpty(29), ptmBusError(30), pmProgramCounterError(31), pmStatsBUSError(32), pmFDIBHPIBUSError(33), pmEME1ParityError(34), pmEME0ParityError(35), pmMulticastError(36), pmFrameError(37), pmPopRollover(38), pmReleaseError(39), amUnsupportedOptypeForRegionOrDeviceException(40), amIllegalRegionOrSubregionException(41), amSearchRunOnException(42), amSearchBusErrorException(43), amParityErrorException(44), amProtocolErrorException(45), amIllegalArgumentException(46), amNonAllignedAddressException(47), amPacketMemoryBusErrorException(48), amPacketHeaderAddressErrorException(49), amLookupContinueZeroException(50), amUnsupportedRSVD8Exception(51), amUnsupportedRSVD10Exception(52), amUnsupportedRSVD1Exception(53), amUnsupportedRSVD2Exception(54), amUnsupportedRSVD3Exception(55), amUnsupportedRSVD4Exception(56), amUnsupportedRSVD5Exception(57), amUnsupportedUnknownHWFailureException(58), amSoftwareInterrupt(59), missingRSPHeartbeats(60)

rcKhiForwardingRSPStateLeftLnHealthStatus		1.3.6.1.4.1.2272.1.85.6.2.1.6
Indicates the Left Lane RSP-State Health as Green/Yellow/Red. If multiple events with different health status occurs at the same time, the highest health status of all the events is reported.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingRSPStateMidLnHealthStatus		1.3.6.1.4.1.2272.1.85.6.2.1.7
Indicates the Middle Lane RSP-State Health as Green/Yellow/Red. If multiple events with different health status occurs at the same time, the highest health status of all the events is reported.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingRSPStateRightLnHealthStatus		1.3.6.1.4.1.2272.1.85.6.2.1.8
Indicates the Right Lane RSP-State Health as Green/Yellow/Red. If multiple events with different health status occurs at the same time, the highest health status of all the events is reported.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingRSPStatsTable		1.3.6.1.4.1.2272.1.85.6.3
Forwarding Key Health Indicator MIB - RSP Stats.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcKhiForwardingRSPStatsEntry

rcKhiForwardingRSPStatsEntry		1.3.6.1.4.1.2272.1.85.6.3.1
Forwarding KHI - RSP Stats table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcKhiForwardingRSPStatsEntry

rcKhiForwardingRSPStatsSlotNumber		1.3.6.1.4.1.2272.1.85.6.3.1.1
Slot Number.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..10

rcKhiForwardingRSPStatsDirection		1.3.6.1.4.1.2272.1.85.6.3.1.2
Direction - Ingress or Egress.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	ingress(1), egress(2)

rcKhiForwardingRSPStatsLeftLnTotalAMPkts		1.3.6.1.4.1.2272.1.85.6.3.1.3
Left Lane RSP Total AM Packets.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcKhiForwardingRSPStatsMidLnTotalAMPkts		1.3.6.1.4.1.2272.1.85.6.3.1.4
Middle Lane RSP Total AM Packets.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcKhiForwardingRSPStatsRightLnTotalAMPkts		1.3.6.1.4.1.2272.1.85.6.3.1.5
Right Lane RSP Total AM Packets.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcKhiForwardingRSPStatsLeftLnTotalAMRxErrPkts		1.3.6.1.4.1.2272.1.85.6.3.1.6
Left Lane RSP Total AM Rx Error Packets Count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcKhiForwardingRSPStatsMidLnTotalAMRxErrPkts		1.3.6.1.4.1.2272.1.85.6.3.1.7
Middle Lane RSP Total AM Rx Error Packets Count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcKhiForwardingRSPStatsRightLnTotalAMRxErrPkts		1.3.6.1.4.1.2272.1.85.6.3.1.8
Right Lane RSP Total AM Rx Error Packets Count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcKhiForwardingRSPStatsLeftLnAMRxErrPktsStatus		1.3.6.1.4.1.2272.1.85.6.3.1.9
Left Lane RSP Total AM Rx Error Packets Health Status. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Red.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingRSPStatsMidLnAMRxErrPktsStatus		1.3.6.1.4.1.2272.1.85.6.3.1.10
Middle Lane RSP Total AM Rx Error Packets Health Status. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Red.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingRSPStatsRightLnAMRxErrPktsStatus		1.3.6.1.4.1.2272.1.85.6.3.1.11
Right Lane RSP Total AM Rx Error Packets Health Status. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Red.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingRSPStatsLeftLnTotalAMShortPkts		1.3.6.1.4.1.2272.1.85.6.3.1.12
Left Lane RSP Total AM Short Packets Count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcKhiForwardingRSPStatsMidLnTotalAMShortPkts		1.3.6.1.4.1.2272.1.85.6.3.1.13
Middle Lane RSP Total AM Short Packets Count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcKhiForwardingRSPStatsRightLnTotalAMShortPkts		1.3.6.1.4.1.2272.1.85.6.3.1.14
Right Lane RSP Total AM Short Packets Count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcKhiForwardingRSPStatsLeftLnAMShortPktsStatus		1.3.6.1.4.1.2272.1.85.6.3.1.15
Left Lane RSP Total AM Short Packets Health Status. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Red.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingRSPStatsMidLnAMShortPktsStatus		1.3.6.1.4.1.2272.1.85.6.3.1.16
Middle Lane RSP Total AM Short Packets Health Status. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Red.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingRSPStatsRightLnAMShortPktsStatus		1.3.6.1.4.1.2272.1.85.6.3.1.17
Right Lane RSP Total AM Short Packets Health Status. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Red.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingRSPStatsLeftLnTotalAMCongestionDrops		1.3.6.1.4.1.2272.1.85.6.3.1.18
Left Lane RSP Total AM Congestion Drop Count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcKhiForwardingRSPStatsMidLnTotalAMCongestionDrops		1.3.6.1.4.1.2272.1.85.6.3.1.19
Middle Lane RSP Total AM Congestion Drop Count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcKhiForwardingRSPStatsRightLnTotalAMCongestionDrops		1.3.6.1.4.1.2272.1.85.6.3.1.20
Right Lane RSP Total AM Congestion Drop Count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcKhiForwardingRSPStatsLeftLnAMCongestionDropStatus		1.3.6.1.4.1.2272.1.85.6.3.1.21
Left Lane RSP Total AM Congestion Drop Health Status. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Yellow.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingRSPStatsMidLnAMCongestionDropStatus		1.3.6.1.4.1.2272.1.85.6.3.1.22
Middle Lane RSP Total AM Congestion Drop Health Status. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Yellow.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingRSPStatsRightLnAMCongestionDropStatus		1.3.6.1.4.1.2272.1.85.6.3.1.23
Right Lane RSP Total AM Congestion Drop Health Status. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Yellow.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingRSPStatsLeftLnTotalAMProcErrPkts		1.3.6.1.4.1.2272.1.85.6.3.1.24
Left Lane RSP Total AM Proc Error Packets Count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcKhiForwardingRSPStatsMidLnTotalAMProcErrPkts		1.3.6.1.4.1.2272.1.85.6.3.1.25
Middle Lane RSP Total AM Proc Error Packets Count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcKhiForwardingRSPStatsRightLnTotalAMProcErrPkts		1.3.6.1.4.1.2272.1.85.6.3.1.26
Right Lane RSP Total AM Proc Error Packets Count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcKhiForwardingRSPStatsLeftLnAMProcErrPktsStatus		1.3.6.1.4.1.2272.1.85.6.3.1.27
Left Lane RSP Total AM Proc Error Packets Health Status. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Yellow.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingRSPStatsMidLnAMProcErrPktsStatus		1.3.6.1.4.1.2272.1.85.6.3.1.28
Middle Lane RSP Total AM Proc Error Packets Health Status. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Yellow.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingRSPStatsRightLnAMProcErrPktsStatus		1.3.6.1.4.1.2272.1.85.6.3.1.29
Right Lane RSP Total AM Proc Error Packets Health Status. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Yellow.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingRSPStatsLeftLnTotalAMExpPkts		1.3.6.1.4.1.2272.1.85.6.3.1.30
Left Lane RSP Total AM Exp Packets Count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcKhiForwardingRSPStatsMidLnTotalAMExpPkts		1.3.6.1.4.1.2272.1.85.6.3.1.31
Middle Lane RSP Total AM Exp Packets Count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcKhiForwardingRSPStatsRightLnTotalAMExpPkts		1.3.6.1.4.1.2272.1.85.6.3.1.32
Right Lane RSP Total AM Exp Packets Count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcKhiForwardingRSPStatsLeftLnAMExpPktsStatus		1.3.6.1.4.1.2272.1.85.6.3.1.33
Left Lane RSP Total AM Exp Packets Health Status. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Yellow.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingRSPStatsMidLnAMExpPktsStatus		1.3.6.1.4.1.2272.1.85.6.3.1.34
Middle Lane RSP Total AM Exp Packets Health Status. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Yellow.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingRSPStatsRightLnAMExpPktsStatus		1.3.6.1.4.1.2272.1.85.6.3.1.35
Right Lane RSP Total AM Exp Packets Health Status. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Yellow.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingRSPStatsLeftLnTotalPMFwdPkts		1.3.6.1.4.1.2272.1.85.6.3.1.36
Left Lane RSP Total PM Forwarded Packets Count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcKhiForwardingRSPStatsMidLnTotalPMFwdPkts		1.3.6.1.4.1.2272.1.85.6.3.1.37
Middle Lane RSP Total PM Forwarded Packets Count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcKhiForwardingRSPStatsRightLnTotalPMFwdPkts		1.3.6.1.4.1.2272.1.85.6.3.1.38
Right Lane RSP Total PM Forwarded Packets Count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcKhiForwardingRSPStatsLeftLnTotalPMDropErrPkts		1.3.6.1.4.1.2272.1.85.6.3.1.39
Left Lane RSP Total PM Dropped Error Packets Count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcKhiForwardingRSPStatsMidLnTotalPMDropErrPkts		1.3.6.1.4.1.2272.1.85.6.3.1.40
Middle Lane RSP Total PM Dropped Error Packets Count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcKhiForwardingRSPStatsRightLnTotalPMDropErrPkts		1.3.6.1.4.1.2272.1.85.6.3.1.41
Right Lane RSP Total PM Dropped Error Packets Count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcKhiForwardingRSPStatsLeftLnPMDropErrStatus		1.3.6.1.4.1.2272.1.85.6.3.1.42
Left Lane RSP Total PM Dropped Error Packets Health Status. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Yellow.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingRSPStatsMidLnPMDropErrStatus		1.3.6.1.4.1.2272.1.85.6.3.1.43
Middle Lane RSP Total PM Dropped Error Packets Health Status. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Yellow.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingRSPStatsRightLnPMDropErrStatus		1.3.6.1.4.1.2272.1.85.6.3.1.44
Right Lane RSP Total PM Dropped Error Packets Health Status. A zero count would indicate a Health Status of Green and a non-zero count would indicate a Yellow.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingF2XHealthTable		1.3.6.1.4.1.2272.1.85.6.4
Forwarding Key Health Indicator MIB - F2X (F2I and F2E) Health.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcKhiForwardingF2XHealthEntry

rcKhiForwardingF2XHealthEntry		1.3.6.1.4.1.2272.1.85.6.4.1
Forwarding KHI - F2X Health table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcKhiForwardingF2XHealthEntry

rcKhiForwardingF2XHealthSlotNumber		1.3.6.1.4.1.2272.1.85.6.4.1.1
Slot Number.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..10

rcKhiForwardingF2XHealthLeftLnErrMask		1.3.6.1.4.1.2272.1.85.6.4.1.2
Left Lane F2X Health Bit Mask. Each bit in the mask represents a specific F2X event. The following are the events - Bit 0 - Police Drops. Indicates a Status of Yellow. Bit 1 - FOQ Drops. Indicates a Status of Yellow. Bit 2 - Fabric Drops. Indicates a Status of Yellow. Bit 3 - Legacy Drops. Indicates a Status of Yellow. Bit 4 - F2E Combined Packet Memory Threshold Exceeded. Indicates a Status of Yellow. Bit 5 - F2E HAB Master - FIFO Parity Error. Indicates a Status of Yellow. Bit 6 - F2E Egress SPI-4.2 Sync Error. Indicates a Status of Red. Bit 7 - F2E Loop SPI-4.2 Sync Error. Indicates a Status of Red. Bit 8 - F2E CIF Illegal Operation. Indicates a Status of Yellow. Bit 9 - F2E CIF Protocol Error. Indicates a Status of Yellow. Bit 10 - F2E CIF Errored Data. Indicates a Status of Yellow. Bit 11 - F2E CIF Illegal Address. Indicates a Status of Yellow. Bit 12 - F2E CIF Read Error in Target Data. Indicates a Status of Yellow. Bit 13 - F2E Egress Queue Drops. Indicates a Status of Red. Bit 14 - F2I Ingress SPI-4.2 Protocol Error. Indicates a Status of Yellow. Bit 15 - F2I Ingress SPI-4.2 Overflow Error. Indicates a Status of Red. Bit 16 - F2I Ingress SPI-4.2 Abort Received. Indicates a Status of Yellow. Bit 17 - F2I Ingress SPI-4.2 Data DIP4 Error Detected. Indicates a Status of Yellow. Bit 18 - F2I Ingress SPI-4.2 Sync Error. Indicates a Status of Red. Bit 19 - F2I Loop SPI-4.2 Protocol Error. Indicates a Status of Yellow. Bit 20 - F2I Loop SPI-4.2 Overflow Error. Indicates a Status of Yellow. Bit 21 - F2I Loop SPI-4.2 Abort Received. Indicates a Status of Yellow. Bit 22 - F2I Loop SPI-4.2 Data DIP4 Error Detected. Indicates a Status of Yellow. Bit 23 - F2I Loop SPI-4.2 Sync Error. Indicates a Status of Red. Bit 24 - F2I HAB Slave FIFO Parity Error. Indicates a Status of Yellow. Bit 25 - F2I HAB Slave FIFO Overflow. Indicates a Status of Red. Bit 26 - F2I HAB Slave Data Parity Error. Indicates a Status of Yellow. Bit 27 - F2I HAB Slave Protocol Error. Indicates a Status of Yellow. Bit 28 - F2I HAB Slave Data Error. Indicates a Status of Yellow. Bit 29 - F2I FOQM Protocol Error. Indicates a Status of Red. Bit 30 - F2I FOQM Overflow. Indicates a Status of Red. Bit 31 - F2E Packet Parity Error. Indicates a status of Red. Bit 32 - F2E Parity Error in Packet Memory Data (QDR). Indicates a status of Red. Bit 33 - F2E Parity Error in Packet Memory Control (QDR). Indicates a status of Red. Bit 34 - F2E Packet Memory Parity Error (QDR). Indicates a status of Red.
Status: current	Access: read-only
OBJECT-TYPE
	BITS	policeDrops(0), foqDrops(1), fabricDrops(2), legacyDrops(3), f2eCombinedPktMemoryThresholdExceeded(4), f2eHABMasterFIFOParityErr(5), f2eEgressSPI42SyncErr(6), f2eLoopSPI42SyncErr(7), f2eCIFIllegalOperation(8), f2eCIFProtocolErr(9), f2eCIFErroredData(10), f2eCIFIllegalAddress(11), f2eCIFReadErrInTargetData(12), f2eEgressQueueDrops(13), f2iIngressSPI42ProtocolErr(14), f2iIngressSPI42OverflowErr(15), f2iIngressSPI42AbortReceived(16), f2iIngressSPI42DataDIP4ErrDetected(17), f2iIngressSPI42SyncErr(18), f2iLoopSPI42ProtocolErr(19), f2iLoopSPI42OverflowErr(20), f2iLoopSPI42AbortReceived(21), f2iLoopSPI42DataDIP4ErrDetected(22), f2iLoopSPI42SyncErr(23), f2iHABSlaveFIFOParityErr(24), f2iHABSlaveFIFOOverflow(25), f2iHABSlaveDataParityErr(26), f2iHABSlaveProtocolErr(27), f2iHABSlaveDataErr(28), f2iFOQMProtocolErr(29), f2iFOQMOverflow(30), f2ePacketParityErrDetected(31), f2eParityErrInPktMemoryData(32), f2eParityErrInPktMemoryControl(33), f2ePktMemoryParityErr(34)

rcKhiForwardingF2XHealthMidLnErrMask		1.3.6.1.4.1.2272.1.85.6.4.1.3
Middle Lane F2X Health Bit Mask. Each bit in the mask represents a specific F2X event. The following are the events - Bit 0 - Police Drops. Indicates a Status of Yellow. Bit 1 - FOQ Drops. Indicates a Status of Yellow. Bit 2 - Fabric Drops. Indicates a Status of Yellow. Bit 3 - Legacy Drops. Indicates a Status of Yellow. Bit 4 - F2E Combined Packet Memory Threshold Exceeded. Indicates a Status of Yellow. Bit 5 - F2E HAB Master - FIFO Parity Error. Indicates a Status of Yellow. Bit 6 - F2E Egress SPI-4.2 Sync Error. Indicates a Status of Red. Bit 7 - F2E Loop SPI-4.2 Sync Error. Indicates a Status of Red. Bit 8 - F2E CIF Illegal Operation. Indicates a Status of Yellow. Bit 9 - F2E CIF Protocol Error. Indicates a Status of Yellow. Bit 10 - F2E CIF Errored Data. Indicates a Status of Yellow. Bit 11 - F2E CIF Illegal Address. Indicates a Status of Yellow. Bit 12 - F2E CIF Read Error in Target Data. Indicates a Status of Yellow. Bit 13 - F2E Egress Queue Drops. Indicates a Status of Red. Bit 14 - F2I Ingress SPI-4.2 Protocol Error. Indicates a Status of Yellow. Bit 15 - F2I Ingress SPI-4.2 Overflow Error. Indicates a Status of Red. Bit 16 - F2I Ingress SPI-4.2 Abort Received. Indicates a Status of Yellow. Bit 17 - F2I Ingress SPI-4.2 Data DIP4 Error Detected. Indicates a Status of Yellow. Bit 18 - F2I Ingress SPI-4.2 Sync Error. Indicates a Status of Red. Bit 19 - F2I Loop SPI-4.2 Protocol Error. Indicates a Status of Yellow. Bit 20 - F2I Loop SPI-4.2 Overflow Error. Indicates a Status of Yellow. Bit 21 - F2I Loop SPI-4.2 Abort Received. Indicates a Status of Yellow. Bit 22 - F2I Loop SPI-4.2 Data DIP4 Error Detected. Indicates a Status of Yellow. Bit 23 - F2I Loop SPI-4.2 Sync Error. Indicates a Status of Red. Bit 24 - F2I HAB Slave FIFO Parity Error. Indicates a Status of Yellow. Bit 25 - F2I HAB Slave FIFO Overflow. Indicates a Status of Red. Bit 26 - F2I HAB Slave Data Parity Error. Indicates a Status of Yellow. Bit 27 - F2I HAB Slave Protocol Error. Indicates a Status of Yellow. Bit 28 - F2I HAB Slave Data Error. Indicates a Status of Yellow. Bit 29 - F2I FOQM Protocol Error. Indicates a Status of Red. Bit 30 - F2I FOQM Overflow. Indicates a Status of Red. Bit 31 - F2E Packet Parity Error. Indicates a status of Red. Bit 32 - F2E Parity Error in Packet Memory Data (QDR). Indicates a status of Red. Bit 33 - F2E Parity Error in Packet Memory Control (QDR). Indicates a status of Red. Bit 34 - F2E Packet Memory Parity Error (QDR). Indicates a status of Red.
Status: current	Access: read-only
OBJECT-TYPE
	BITS	policeDrops(0), foqDrops(1), fabricDrops(2), legacyDrops(3), f2eCombinedPktMemoryThresholdExceeded(4), f2eHABMasterFIFOParityErr(5), f2eEgressSPI42SyncErr(6), f2eLoopSPI42SyncErr(7), f2eCIFIllegalOperation(8), f2eCIFProtocolErr(9), f2eCIFErroredData(10), f2eCIFIllegalAddress(11), f2eCIFReadErrInTargetData(12), f2eEgressQueueDrops(13), f2iIngressSPI42ProtocolErr(14), f2iIngressSPI42OverflowErr(15), f2iIngressSPI42AbortReceived(16), f2iIngressSPI42DataDIP4ErrDetected(17), f2iIngressSPI42SyncErr(18), f2iLoopSPI42ProtocolErr(19), f2iLoopSPI42OverflowErr(20), f2iLoopSPI42AbortReceived(21), f2iLoopSPI42DataDIP4ErrDetected(22), f2iLoopSPI42SyncErr(23), f2iHABSlaveFIFOParityErr(24), f2iHABSlaveFIFOOverflow(25), f2iHABSlaveDataParityErr(26), f2iHABSlaveProtocolErr(27), f2iHABSlaveDataErr(28), f2iFOQMProtocolErr(29), f2iFOQMOverflow(30), f2ePacketParityErrDetected(31), f2eParityErrInPktMemoryData(32), f2eParityErrInPktMemoryControl(33), f2ePktMemoryParityErr(34)

rcKhiForwardingF2XHealthRightLnErrMask		1.3.6.1.4.1.2272.1.85.6.4.1.4
Right Lane F2X Health Bit Mask. Each bit in the mask represents a specific F2X event. The following are the events - Bit 0 - Police Drops. Indicates a Status of Yellow. Bit 1 - FOQ Drops. Indicates a Status of Yellow. Bit 2 - Fabric Drops. Indicates a Status of Yellow. Bit 3 - Legacy Drops. Indicates a Status of Yellow. Bit 4 - F2E Combined Packet Memory Threshold Exceeded. Indicates a Status of Yellow. Bit 5 - F2E HAB Master - FIFO Parity Error. Indicates a Status of Yellow. Bit 6 - F2E Egress SPI-4.2 Sync Error. Indicates a Status of Red. Bit 7 - F2E Loop SPI-4.2 Sync Error. Indicates a Status of Red. Bit 8 - F2E CIF Illegal Operation. Indicates a Status of Yellow. Bit 9 - F2E CIF Protocol Error. Indicates a Status of Yellow. Bit 10 - F2E CIF Errored Data. Indicates a Status of Yellow. Bit 11 - F2E CIF Illegal Address. Indicates a Status of Yellow. Bit 12 - F2E CIF Read Error in Target Data. Indicates a Status of Yellow. Bit 13 - F2E Egress Queue Drops. Indicates a Status of Red. Bit 14 - F2I Ingress SPI-4.2 Protocol Error. Indicates a Status of Yellow. Bit 15 - F2I Ingress SPI-4.2 Overflow Error. Indicates a Status of Red. Bit 16 - F2I Ingress SPI-4.2 Abort Received. Indicates a Status of Yellow. Bit 17 - F2I Ingress SPI-4.2 Data DIP4 Error Detected. Indicates a Status of Yellow. Bit 18 - F2I Ingress SPI-4.2 Sync Error. Indicates a Status of Red. Bit 19 - F2I Loop SPI-4.2 Protocol Error. Indicates a Status of Yellow. Bit 20 - F2I Loop SPI-4.2 Overflow Error. Indicates a Status of Yellow. Bit 21 - F2I Loop SPI-4.2 Abort Received. Indicates a Status of Yellow. Bit 22 - F2I Loop SPI-4.2 Data DIP4 Error Detected. Indicates a Status of Yellow. Bit 23 - F2I Loop SPI-4.2 Sync Error. Indicates a Status of Red. Bit 24 - F2I HAB Slave FIFO Parity Error. Indicates a Status of Yellow. Bit 25 - F2I HAB Slave FIFO Overflow. Indicates a Status of Red. Bit 26 - F2I HAB Slave Data Parity Error. Indicates a Status of Yellow. Bit 27 - F2I HAB Slave Protocol Error. Indicates a Status of Yellow. Bit 28 - F2I HAB Slave Data Error. Indicates a Status of Yellow. Bit 29 - F2I FOQM Protocol Error. Indicates a Status of Red. Bit 30 - F2I FOQM Overflow. Indicates a Status of Red. Bit 31 - F2E Packet Parity Error. Indicates a status of Red. Bit 32 - F2E Parity Error in Packet Memory Data (QDR). Indicates a status of Red. Bit 33 - F2E Parity Error in Packet Memory Control (QDR). Indicates a status of Red. Bit 34 - F2E Packet Memory Parity Error (QDR). Indicates a status of Red.
Status: current	Access: read-only
OBJECT-TYPE
	BITS	policeDrops(0), foqDrops(1), fabricDrops(2), legacyDrops(3), f2eCombinedPktMemoryThresholdExceeded(4), f2eHABMasterFIFOParityErr(5), f2eEgressSPI42SyncErr(6), f2eLoopSPI42SyncErr(7), f2eCIFIllegalOperation(8), f2eCIFProtocolErr(9), f2eCIFErroredData(10), f2eCIFIllegalAddress(11), f2eCIFReadErrInTargetData(12), f2eEgressQueueDrops(13), f2iIngressSPI42ProtocolErr(14), f2iIngressSPI42OverflowErr(15), f2iIngressSPI42AbortReceived(16), f2iIngressSPI42DataDIP4ErrDetected(17), f2iIngressSPI42SyncErr(18), f2iLoopSPI42ProtocolErr(19), f2iLoopSPI42OverflowErr(20), f2iLoopSPI42AbortReceived(21), f2iLoopSPI42DataDIP4ErrDetected(22), f2iLoopSPI42SyncErr(23), f2iHABSlaveFIFOParityErr(24), f2iHABSlaveFIFOOverflow(25), f2iHABSlaveDataParityErr(26), f2iHABSlaveProtocolErr(27), f2iHABSlaveDataErr(28), f2iFOQMProtocolErr(29), f2iFOQMOverflow(30), f2ePacketParityErrDetected(31), f2eParityErrInPktMemoryData(32), f2eParityErrInPktMemoryControl(33), f2ePktMemoryParityErr(34)

rcKhiForwardingF2XHealthLeftLnHealthStatus		1.3.6.1.4.1.2272.1.85.6.4.1.5
Indicates the Left Lane F2X Health as Green/Yellow/Red. If multiple events with different health status occurs at the same time, the highest health status of all the events is reported.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingF2XHealthMidLnHealthStatus		1.3.6.1.4.1.2272.1.85.6.4.1.6
Indicates the Middle Lane F2X Health as Green/Yellow/Red. If multiple events with different health status occurs at the same time, the highest health status of all the events is reported.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingF2XHealthRightLnHealthStatus		1.3.6.1.4.1.2272.1.85.6.4.1.7
Indicates the Right Lane F2X Health as Green/Yellow/Red. If multiple events with different health status occurs at the same time, the highest health status of all the events is reported.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingHistoryTable		1.3.6.1.4.1.2272.1.85.6.5
Forwarding Key Health Indicator MIB - Historical Data.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcKhiForwardingHistoryEntry

rcKhiForwardingHistoryEntry		1.3.6.1.4.1.2272.1.85.6.5.1
Forwarding KHI - History table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcKhiForwardingHistoryEntry

rcKhiForwardingHistoryIndex		1.3.6.1.4.1.2272.1.85.6.5.1.1
Index for Forwarding Health historical data.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..10

rcKhiForwardingHistoryTimeStamp		1.3.6.1.4.1.2272.1.85.6.5.1.2
Timestamp indicating when a particular event occurred.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiForwardingHistorySlotNumber		1.3.6.1.4.1.2272.1.85.6.5.1.3
Slot Number.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..10

rcKhiForwardingHistoryLane		1.3.6.1.4.1.2272.1.85.6.5.1.4
Lane where the event occurred.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	leftLane(1), middleLane(2), rightLane(3)

rcKhiForwardingHistoryEvent		1.3.6.1.4.1.2272.1.85.6.5.1.5
Name of the event
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..50)

rcKhiForwardingCurrentStatusTable		1.3.6.1.4.1.2272.1.85.6.6
Forwarding Key Health Indicator MIB - Current Status Info.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcKhiForwardingCurrentStatusEntry

rcKhiForwardingCurrentStatusEntry		1.3.6.1.4.1.2272.1.85.6.6.1
Forwarding KHI - Current Status table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcKhiForwardingCurrentStatusEntry

rcKhiForwardingCurrentStatusSlotNumber		1.3.6.1.4.1.2272.1.85.6.6.1.1
Slot Number.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..10

rcKhiForwardingCurrentStatusLeftLnHealth		1.3.6.1.4.1.2272.1.85.6.6.1.2
Indicates the Left Lane Current Health as Green/Yellow/Red. If multiple events with different health status occurs at the same time, the highest health status of all the events is reported.Slot Number.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingCurrentStatusLeftLnErrMask		1.3.6.1.4.1.2272.1.85.6.6.1.3
Left Lane Current Status Health Bit Mask. Each bit in the mask represents what kind of errors the lane is currently experiencing. The following are the events - Bit 0 - Asic Resets. Bit 1 - RSP State Errors. Bit 2 - RSP Stats Errors. Bit 3 - F2X Errors.
Status: current	Access: read-only
OBJECT-TYPE
	BITS	asicResets(0), rspStateErrors(1), rspStatsErrors(2), f2xErrors(3)

rcKhiForwardingCurrentStatusMidLnHealth		1.3.6.1.4.1.2272.1.85.6.6.1.4
Indicates the Middle Lane Current Health as Green/Yellow/Red. If multiple events with different health status occurs at the same time, the highest health status of all the events is reported.Slot Number.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingCurrentStatusMidLnErrMask		1.3.6.1.4.1.2272.1.85.6.6.1.5
Middle Lane Current Status Health Bit Mask. Each bit in the mask represents what kind of errors the lane is currently experiencing. The following are the events - Bit 0 - Asic Resets. Bit 1 - RSP State Errors. Bit 2 - RSP Stats Errors. Bit 3 - F2X Errors.
Status: current	Access: read-only
OBJECT-TYPE
	BITS	asicResets(0), rspStateErrors(1), rspStatsErrors(2), f2xErrors(3)

rcKhiForwardingCurrentStatusRightLnHealth		1.3.6.1.4.1.2272.1.85.6.6.1.6
Indicates the Right Lane Current Health as Green/Yellow/Red. If multiple events with different health status occurs at the same time, the highest health status of all the events is reported.Slot Number.
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiForwardingCurrentStatusRightLnErrMask		1.3.6.1.4.1.2272.1.85.6.6.1.7
Right Lane Current Status Health Bit Mask. Each bit in the mask represents what kind of errors the lane is currently experiencing. The following are the events - Bit 0 - Asic Resets. Bit 1 - RSP State Errors. Bit 2 - RSP Stats Errors. Bit 3 - F2X Errors.
Status: current	Access: read-only
OBJECT-TYPE
	BITS	asicResets(0), rspStateErrors(1), rspStatsErrors(2), f2xErrors(3)

rcKhiProtocol		1.3.6.1.4.1.2272.1.85.7
OBJECT IDENTIFIER

rcKhiOspfTable		1.3.6.1.4.1.2272.1.85.7.1
Ospf protcol KHI summary
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcKhiOspfEntry

rcKhiOspfEntry		1.3.6.1.4.1.2272.1.85.7.1.1
Ospf protcol KHI summary entry
Status: current	Access: not-accessible
OBJECT-TYPE
	RcKhiOspfEntry

rcKhiOspfVrfId		1.3.6.1.4.1.2272.1.85.7.1.1.1
An unique index used to identify a particular fan in the system.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..255

rcKhiOspfRouteTableSize		1.3.6.1.4.1.2272.1.85.7.1.1.2
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiOspfRefRouteTableSize		1.3.6.1.4.1.2272.1.85.7.1.1.3
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiOspfLsdbTableSize		1.3.6.1.4.1.2272.1.85.7.1.1.4
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiOspfNumOfInterfaces		1.3.6.1.4.1.2272.1.85.7.1.1.5
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiOspfNumOfAdjacency		1.3.6.1.4.1.2272.1.85.7.1.1.6
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiOspfRefNumOfAdjacency		1.3.6.1.4.1.2272.1.85.7.1.1.7
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiOspfLastClearTimestamp		1.3.6.1.4.1.2272.1.85.7.1.1.8
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiOspfFirstEventTimestamp		1.3.6.1.4.1.2272.1.85.7.1.1.9
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiOspfHistoryTable		1.3.6.1.4.1.2272.1.85.7.2
Ospf protcol KHI summary
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcKhiOspfHistoryEntry

rcKhiOspfHistoryEntry		1.3.6.1.4.1.2272.1.85.7.2.1
Ospf protcol KHI summary entry
Status: current	Access: not-accessible
OBJECT-TYPE
	RcKhiOspfHistoryEntry

rcKhiOspfHistoryVrfId		1.3.6.1.4.1.2272.1.85.7.2.1.1
An unique index used to identify a particular fan in the system.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..255

rcKhiOspfHistoryIndex		1.3.6.1.4.1.2272.1.85.7.2.1.2
History index for a particular VRF OSPF
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..10

rcKhiOspfHistoryLsdbTableSize		1.3.6.1.4.1.2272.1.85.7.2.1.3
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiOspfHistoryNumOfAdjacency		1.3.6.1.4.1.2272.1.85.7.2.1.4
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiOspfHistoryTimestamp		1.3.6.1.4.1.2272.1.85.7.2.1.5
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiBgpTable		1.3.6.1.4.1.2272.1.85.7.3
Bgp protcol KHI summary
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcKhiBgpEntry

rcKhiBgpEntry		1.3.6.1.4.1.2272.1.85.7.3.1
Bgp protcol KHI summary entry
Status: current	Access: not-accessible
OBJECT-TYPE
	RcKhiBgpEntry

rcKhiBgpVrfId		1.3.6.1.4.1.2272.1.85.7.3.1.1
An unique index used to identify a particular fan in the system.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..255

rcKhiBgpUpdateSent		1.3.6.1.4.1.2272.1.85.7.3.1.2
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiBgpUpdateRecvd		1.3.6.1.4.1.2272.1.85.7.3.1.3
Update received
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiBgpNotifySent		1.3.6.1.4.1.2272.1.85.7.3.1.4
Notify sent
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiBgpNotifyRecvd		1.3.6.1.4.1.2272.1.85.7.3.1.5
BGP Notify received
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiBgpBadEvents		1.3.6.1.4.1.2272.1.85.7.3.1.6
BGP bad event count
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiBgpRouteTableSize		1.3.6.1.4.1.2272.1.85.7.3.1.7
BGP route table size
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiBgpRefRouteTableSize		1.3.6.1.4.1.2272.1.85.7.3.1.8
BGP reference route table size
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiBgpEstablishedNbrs		1.3.6.1.4.1.2272.1.85.7.3.1.9
BGP established neighbor
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiBgpRefEstablishedNbrs		1.3.6.1.4.1.2272.1.85.7.3.1.10
BGP established neighbor
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiBgpNumOfAggregates		1.3.6.1.4.1.2272.1.85.7.3.1.11
Number of aggregates
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiBgpNumOfImportedRoutes		1.3.6.1.4.1.2272.1.85.7.3.1.12
Number of imported routes
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiBgpLastClearTimestamp		1.3.6.1.4.1.2272.1.85.7.3.1.13
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiBgpFirstEventTimestamp		1.3.6.1.4.1.2272.1.85.7.3.1.14
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiBgpHistoryTable		1.3.6.1.4.1.2272.1.85.7.4
Bgp protcol KHI summary
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcKhiBgpHistoryEntry

rcKhiBgpHistoryEntry		1.3.6.1.4.1.2272.1.85.7.4.1
Bgp protcol KHI summary entry
Status: current	Access: not-accessible
OBJECT-TYPE
	RcKhiBgpHistoryEntry

rcKhiBgpHistoryVrfId		1.3.6.1.4.1.2272.1.85.7.4.1.1
An unique index used to identify a particular fan in the system.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..255

rcKhiBgpHistoryIndex		1.3.6.1.4.1.2272.1.85.7.4.1.2
History index for a particular VRF OSPF
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..10

rcKhiBgpHistoryRibCount		1.3.6.1.4.1.2272.1.85.7.4.1.3
Number of BGP Rib
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiBgpHistoryNumOfPeers		1.3.6.1.4.1.2272.1.85.7.4.1.4
Number of BGP peers
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiBgpHistoryTimestamp		1.3.6.1.4.1.2272.1.85.7.4.1.5
BGP history timestamp
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiPimTable		1.3.6.1.4.1.2272.1.85.7.5
Pim protcol KHI summary
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcKhiPimEntry

rcKhiPimEntry		1.3.6.1.4.1.2272.1.85.7.5.1
Pim protcol KHI summary entry
Status: current	Access: not-accessible
OBJECT-TYPE
	RcKhiPimEntry

rcKhiPimVrfId		1.3.6.1.4.1.2272.1.85.7.5.1.1
An unique index used to identify a particular fan in the system.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..255

rcKhiPimRoutes		1.3.6.1.4.1.2272.1.85.7.5.1.2
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiPimRefRoutes		1.3.6.1.4.1.2272.1.85.7.5.1.3
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiPimAdjacencies		1.3.6.1.4.1.2272.1.85.7.5.1.4
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiPimRefAdjacencies		1.3.6.1.4.1.2272.1.85.7.5.1.5
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiPimLastClearTimestamp		1.3.6.1.4.1.2272.1.85.7.5.1.6
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiPimFirstEventTimestamp		1.3.6.1.4.1.2272.1.85.7.5.1.7
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiPimHistoryTable		1.3.6.1.4.1.2272.1.85.7.6
Pim protcol KHI summary
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcKhiPimHistoryEntry

rcKhiPimHistoryEntry		1.3.6.1.4.1.2272.1.85.7.6.1
Pim protcol KHI summary entry
Status: current	Access: not-accessible
OBJECT-TYPE
	RcKhiPimHistoryEntry

rcKhiPimHistoryVrfId		1.3.6.1.4.1.2272.1.85.7.6.1.1
An unique index used to identify a particular fan in the system.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..255

rcKhiPimHistoryIndex		1.3.6.1.4.1.2272.1.85.7.6.1.2
History index for a particular VRF PIM
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..10

rcKhiPimHistoryRouteCount		1.3.6.1.4.1.2272.1.85.7.6.1.3
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiPimHistoryAdjacencies		1.3.6.1.4.1.2272.1.85.7.6.1.4
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiPimHistoryTimestamp		1.3.6.1.4.1.2272.1.85.7.6.1.5
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiIgmpHistoryTable		1.3.6.1.4.1.2272.1.85.7.7
Igmp protcol KHI summary
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcKhiIgmpHistoryEntry

rcKhiIgmpHistoryEntry		1.3.6.1.4.1.2272.1.85.7.7.1
Igmp protcol KHI summary entry
Status: current	Access: not-accessible
OBJECT-TYPE
	RcKhiIgmpHistoryEntry

rcKhiIgmpHistoryVrfId		1.3.6.1.4.1.2272.1.85.7.7.1.1
An unique index used to identify a particular fan in the system.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..255

rcKhiIgmpHistoryIndex		1.3.6.1.4.1.2272.1.85.7.7.1.2
History index for a particular VRF PIM
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..10

rcKhiIgmpHistoryGroupCount		1.3.6.1.4.1.2272.1.85.7.7.1.3
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiIgmpHistorySenderCount		1.3.6.1.4.1.2272.1.85.7.7.1.4
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiIgmpHistoryTimestamp		1.3.6.1.4.1.2272.1.85.7.7.1.5
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiIgmpSnoopHistoryTable		1.3.6.1.4.1.2272.1.85.7.8
IgmpSnoop protcol KHI summary
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcKhiIgmpSnoopHistoryEntry

rcKhiIgmpSnoopHistoryEntry		1.3.6.1.4.1.2272.1.85.7.8.1
IgmpSnoop protcol KHI summary entry
Status: current	Access: not-accessible
OBJECT-TYPE
	RcKhiIgmpSnoopHistoryEntry

rcKhiIgmpSnoopHistoryVrfId		1.3.6.1.4.1.2272.1.85.7.8.1.1
An unique index used to identify a particular fan in the system.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..255

rcKhiIgmpSnoopHistoryIndex		1.3.6.1.4.1.2272.1.85.7.8.1.2
History index for a particular VRF PIM
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..10

rcKhiIgmpSnoopHistoryStreamCount		1.3.6.1.4.1.2272.1.85.7.8.1.3
IGMP Snoop stream count
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiIgmpSnoopHistoryHostCount		1.3.6.1.4.1.2272.1.85.7.8.1.4
IgmpSnoop hots count
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiIgmpSnoopHistoryTimestamp		1.3.6.1.4.1.2272.1.85.7.8.1.5
Igmp Snoop timestamp
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiVlacpTotalPortCount		1.3.6.1.4.1.2272.1.85.7.9
VLACP port count, where VLACP is enabled
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiVlacpPortUpCount		1.3.6.1.4.1.2272.1.85.7.10
Number of ports where VLACP is up
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiIstState		1.3.6.1.4.1.2272.1.85.7.11
Current IST State for KHI
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiFirstIstSyncTimeStamp		1.3.6.1.4.1.2272.1.85.7.12
Timestamp for the first IST Sync
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiLastIstSyncTimeStamp		1.3.6.1.4.1.2272.1.85.7.13
Timestamp for the last IST Sync
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiNumIstUpEvents		1.3.6.1.4.1.2272.1.85.7.14
Total number of IST up events
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiNumIstDownEvents		1.3.6.1.4.1.2272.1.85.7.15
Total number of IST down events
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiNumSmltDownEventsSent		1.3.6.1.4.1.2272.1.85.7.16
Total number of SMLT down events sent
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiLastSmltDownEventSentTimeStamp		1.3.6.1.4.1.2272.1.85.7.17
Timestamp for the last SMLT down event sent
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiNumSmltDownEventsRecv		1.3.6.1.4.1.2272.1.85.7.18
Total number of SMLT down events received
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiLastSmltDownEventRecvTimeStamp		1.3.6.1.4.1.2272.1.85.7.19
Timestamp for the last SMLT down event received
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiNumSmltUpEventsSent		1.3.6.1.4.1.2272.1.85.7.20
Total number of SMLT up events sent
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiLastSmltUpEventSentTimeStamp		1.3.6.1.4.1.2272.1.85.7.21
Timestamp for the last SMLT up event sent
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiNumSmltUpEventsRecv		1.3.6.1.4.1.2272.1.85.7.22
Total number of SMLT Up events received
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiLastSmltUpEventRecvTimeStamp		1.3.6.1.4.1.2272.1.85.7.23
Timestamp for the last SMLT up event received
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiNumSendMacAddrSent		1.3.6.1.4.1.2272.1.85.7.24
Total number of SMLT send mac addr events sent
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiLastSendMacAddrSentTimeStamp		1.3.6.1.4.1.2272.1.85.7.25
Timestamp for the last SMLT send MAC addr event sent
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiNumSendMacAddrRecv		1.3.6.1.4.1.2272.1.85.7.26
Total number of SMLT send mac addr events recv
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiLastSendMacAddrRecvTimeStamp		1.3.6.1.4.1.2272.1.85.7.27
Timestamp for the last SMLT send MAC addr event received
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiIstHistoryTable		1.3.6.1.4.1.2272.1.85.7.28
Ist protcol KHI history
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcKhiIstHistoryEntry

rcKhiIstHistoryEntry		1.3.6.1.4.1.2272.1.85.7.28.1
Ist protcol KHI history entry
Status: current	Access: not-accessible
OBJECT-TYPE
	RcKhiIstHistoryEntry

rcKhiIstHistoryIndex		1.3.6.1.4.1.2272.1.85.7.28.1.1
History index for a particular IST history entry
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..10

rcKhiIstHistoryIstStatus		1.3.6.1.4.1.2272.1.85.7.28.1.2
Status of the IST
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiIstHistoryTimestamp		1.3.6.1.4.1.2272.1.85.7.28.1.3
Timestamp associated with IST history entry
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiSmltHistoryTable		1.3.6.1.4.1.2272.1.85.7.29
Smlt protocol KHI history
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcKhiSmltHistoryEntry

rcKhiSmltHistoryEntry		1.3.6.1.4.1.2272.1.85.7.29.1
Smlt protcol KHI history entry
Status: current	Access: not-accessible
OBJECT-TYPE
	RcKhiSmltHistoryEntry

rcKhiSmltHistoryIndex		1.3.6.1.4.1.2272.1.85.7.29.1.1
History index for a particular SMLT history entry
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..10

rcKhiSmltHistorySmltId		1.3.6.1.4.1.2272.1.85.7.29.1.2
SMLTID of the SMLT history entry
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcKhiSmltHistorySmltStatus		1.3.6.1.4.1.2272.1.85.7.29.1.3
Status of the SMLT
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiSmltHistoryTimestamp		1.3.6.1.4.1.2272.1.85.7.29.1.4
Timestamp associated with IST history entry
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiSmltTable		1.3.6.1.4.1.2272.1.85.7.30
Smlt protocol KHI
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcKhiSmltEntry

rcKhiSmltEntry		1.3.6.1.4.1.2272.1.85.7.30.1
Smlt protcol KHI entry
Status: current	Access: not-accessible
OBJECT-TYPE
	RcKhiSmltEntry

rcKhiSmltId		1.3.6.1.4.1.2272.1.85.7.30.1.1
SMLTID of the SMLT entry, also used as index
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..512

rcKhiSmltStatus		1.3.6.1.4.1.2272.1.85.7.30.1.2
Status of the SMLT
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiSmltUpEvents		1.3.6.1.4.1.2272.1.85.7.30.1.3
Number of SMLT Up Events
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiSmltDownEvents		1.3.6.1.4.1.2272.1.85.7.30.1.4
Number of SMLT Down Events
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcKhiMgmt		1.3.6.1.4.1.2272.1.85.8
OBJECT IDENTIFIER

rcKhiMgmtCurrentLogStatus		1.3.6.1.4.1.2272.1.85.8.1
The current status of logging task
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiMgmtLogFirstHighestEvent		1.3.6.1.4.1.2272.1.85.8.2
The first change status of the log since last boot or clear. 'green (1)' means log OK. 'red (4)' means log fail
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiMgmtLogFirstHighestEventTime		1.3.6.1.4.1.2272.1.85.8.3
Record the first log task change time The display format in mmddyyhhmmss. If all are zero, it means no change
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiMgmtLogRefStatus		1.3.6.1.4.1.2272.1.85.8.4
Reference status before change since last boot or clear. 'green (1)' means log OK. 'red (4)' means log fail
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiMgmtLogStatusLastClearTime		1.3.6.1.4.1.2272.1.85.8.5
Record the first log task change time The display format in mmddyyhhmmss. If all are zero, it means no change
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiMgmtLogHistoryTable		1.3.6.1.4.1.2272.1.85.8.6
Log history KHI summary
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcKhiMgmtLogHistoryEntry

rcKhiMgmtLogHistoryEntry		1.3.6.1.4.1.2272.1.85.8.6.1
Log sttaus KHI summary entry
Status: current	Access: not-accessible
OBJECT-TYPE
	RcKhiMgmtLogHistoryEntry

rcKhiMgmtLogHistoryIndex		1.3.6.1.4.1.2272.1.85.8.6.1.1
An unique history index used to identify a particular entry in log history.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..10

rcKhiMgmtLogHistoryStatus		1.3.6.1.4.1.2272.1.85.8.6.1.2
Changing Status
Status: current	Access: read-only
OBJECT-TYPE
	KhiStatusValue

rcKhiMgmtLogHistoryTimestamp		1.3.6.1.4.1.2272.1.85.8.6.1.3
Status change timestamp.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiIpInterface		1.3.6.1.4.1.2272.1.85.9
OBJECT IDENTIFIER

rcKhiIpInterfaceHistoryTable		1.3.6.1.4.1.2272.1.85.9.1
Ip Interface Historical Data
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcKhiIpInterfaceHistoryEntry

rcKhiIpInterfaceHistoryEntry		1.3.6.1.4.1.2272.1.85.9.1.1
Ip Interface history table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcKhiIpInterfaceHistoryEntry

rcKhiIpInterfaceHistoryIndex		1.3.6.1.4.1.2272.1.85.9.1.1.1
Historical data index number.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..10

rcKhiIpInterfaceHistoryTimestamp		1.3.6.1.4.1.2272.1.85.9.1.1.2
Timestamp indicating when the event occurred.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

rcKhiIpInterfaceHistoryIpAddr		1.3.6.1.4.1.2272.1.85.9.1.1.3
IP address of the interface.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcKhiIpInterfaceHistoryVlanId		1.3.6.1.4.1.2272.1.85.9.1.1.4
Vlan id of the IP interface.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4094

rcKhiIpInterfaceHistoryEvent		1.3.6.1.4.1.2272.1.85.9.1.1.5
Indicates whether the interface went up or down.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2)

rcIpMpls		1.3.6.1.4.1.2272.1.8.102
OBJECT IDENTIFIER

rcIpMplsIfTable		1.3.6.1.4.1.2272.1.8.102.20
A table used to maintain MPLS information for a particular interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpMplsIfEntry

rcIpMplsIfEntry		1.3.6.1.4.1.2272.1.8.102.20.1
Entry containing MPLS information. An entry is automatically created in this table when MPLS is enabled for an interface -or- when an ip address is configured on an interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpMplsIfEntry

rcIpMplsIfIfIndex		1.3.6.1.4.1.2272.1.8.102.20.1.1
An unique value to identify a physical interface or a logical interface (VLAN).
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndexOrZero	0..6142

rcIpMplsIfLdpAdminState		1.3.6.1.4.1.2272.1.8.102.20.1.2
Indicates whether LDP is enabled on the interface.
Status: current	Access: read-create
OBJECT-TYPE
	EnableValue

rcIpMplsIfLdpSessionKeepAlive		1.3.6.1.4.1.2272.1.8.102.20.1.3
Configures the LDP Session keep alive on the interface. The value 0 is used to indicate a global value. If 0 the interface will use the LDP global value. If greater than 0 this value will override the LDP global value.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0 | 15..65535

rcIpMplsIfLdpHelloHoldTime		1.3.6.1.4.1.2272.1.8.102.20.1.4
Configures the LDP hello hold time on the interface. If 0 the interface will use the LDP global value. If greater than 0 this value will override the LDP global value.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0 | 5..65535

rcIpMplsIfLdpTransportAddr		1.3.6.1.4.1.2272.1.8.102.20.1.5
Configures the transport address of the LDP lsp. If not set then transport address will be the MPLS router id.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	interface(1), router-id(2)

rcIpMplsIfLdpImportPolicy		1.3.6.1.4.1.2272.1.8.102.20.1.6
Configures the LDP import policy behavior. If set to host-only then only host will import policies. If set to all then all interfaces will import policies.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	all(1), host-only(2)

rcIpMplsIfRsvpAdminState		1.3.6.1.4.1.2272.1.8.102.20.1.7
Indicates whether RSVP is enabled on the interface.
Status: current	Access: read-create
OBJECT-TYPE
	EnableValue

rcIpMplsIfRefreshReduction		1.3.6.1.4.1.2272.1.8.102.20.1.8
Indicates whether RSVP refresh reduction is enabled or not. If set to global, refresh reduction will take the global RSVP refresh reduction value.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	enable(1), disable(2), global(3)

rcIpMplsIfRefreshInterval		1.3.6.1.4.1.2272.1.8.102.20.1.9
Configures the RSVP refresh interval on the interface. If set to zero, the refresh interval will default to the global rsvp refresh interval.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..65535

rcIpMplsIfRefreshMultiplier		1.3.6.1.4.1.2272.1.8.102.20.1.10
Configures the RSVP refresh multiplier for the interface. If set to zero, the refresh interval will default to to global rsvp refresh multiplier.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..255

rcIpMplsIfRsvpHelloInterval		1.3.6.1.4.1.2272.1.8.102.20.1.11
Configures the RSVP hello interval on the interface. If 0 the interface will use the RSVP global value. If greater than 0 this value will override the RSVP global value.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..65535

rcIpMplsIfMessageBundling		1.3.6.1.4.1.2272.1.8.102.20.1.12
Indicates whether RSVP message bundling is enabled or not. If set to global, message bundling will take the global RSVP message bundling value.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	enable(1), disable(2), global(3)

rcIpMplsIfMtu		1.3.6.1.4.1.2272.1.8.102.20.1.13
Configures the mtu of the mpls interface. The value cannot exceed that of the system mtu size.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	64..9600

rcIpMplsIfRowStatus		1.3.6.1.4.1.2272.1.8.102.20.1.14
Used to create/delete entries
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcIpInterVrfStaticRoute		1.3.6.1.4.1.2272.1.8.103
OBJECT IDENTIFIER

rcIpInterVrfStaticRouteTableSize		1.3.6.1.4.1.2272.1.8.103.1
size of Ip Static Route Table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpInterVrfStaticRouteTable		1.3.6.1.4.1.2272.1.8.103.2
This table is used to add static IP routes to the device. Routes added into this table will automatically show-up in the 'rcIpRouteTable' when the device is actively using the route to forward IP traffic.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpInterVrfStaticRouteEntry

rcIpInterVrfStaticRouteEntry		1.3.6.1.4.1.2272.1.8.103.2.1
A static route to a particular destination.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpInterVrfStaticRouteEntry

rcIpInterVrfStaticRouteOwnerVrfId		1.3.6.1.4.1.2272.1.8.103.2.1.1
Owner VRF id of the static route
Status: current	Access: not-accessible
OBJECT-TYPE
	VrfIdentifier

rcIpInterVrfStaticRouteDest		1.3.6.1.4.1.2272.1.8.103.2.1.2
The destination IP address of this route. An entry with a value of 0.0.0.0 is considered a default route. Multiple routes to a single destination can appear in the table, but access to such multiple entries is dependent on the table- access mechanisms defined by the network management protocol in use.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rcIpInterVrfStaticRouteMask		1.3.6.1.4.1.2272.1.8.103.2.1.3
Indicate the mask to be logical-ANDed with the destination address before being compared to the value in the rcIpRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the rcIpRouteMask by determining whether the value of the correspondent rcIpRouteDest field belong to a class-A, B, or C network, and then using one of: mask network 255.0.0.0 class-A 255.255.0.0 class-B 255.255.255.0 class-C If the value of the rcIpRouteDest is 0.0.0.0 (a default route), then the mask value is also 0.0.0.0. It should be noted that all IP routing subsystems implicitly use this mechanism.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rcIpInterVrfStaticRouteNextHop		1.3.6.1.4.1.2272.1.8.103.2.1.4
The IP address of the next hop of this route. (In the case of a route bound to an interface which is realized via a broadcast media, the value of this field is the agent's IP address on that interface).
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rcIpInterVrfStaticRouteMetric		1.3.6.1.4.1.2272.1.8.103.2.1.5
The primary routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's rcIpRouteProto value. If this metric is not used, its value should be set to -1.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..FFFF

rcIpInterVrfStaticRouteIfIndex		1.3.6.1.4.1.2272.1.8.103.2.1.6
The index value which uniquely identifies the local interface through which the next hop of this route should be reached. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex	0..65535

rcIpInterVrfStaticRoutePreference		1.3.6.1.4.1.2272.1.8.103.2.1.7
Used to indicate the route preference of this entry. If there are more than one route that can be used to forward IP traffic, the route that has a highest preference will be used instead of a lower preference one. The higher the number, the higher the preference.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..255

rcIpInterVrfStaticRouteEnable		1.3.6.1.4.1.2272.1.8.103.2.1.8
Used to enable/disable this entry.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpInterVrfStaticRouteStatus		1.3.6.1.4.1.2272.1.8.103.2.1.9
Used to indicate the current status of this entry.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	inactive(0), active(1)

rcIpInterVrfStaticRouteRowStatus		1.3.6.1.4.1.2272.1.8.103.2.1.10
Used to create/delete entries
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpInterVrfStaticRouteLocalNextHop		1.3.6.1.4.1.2272.1.8.103.2.1.11
Used to enable/disable this entry. True indicate that the static route becomes active only if switch has a local route to the network. False indicates that the static route becomes active if switch has a local route or dynamic route.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpInterVrfStaticRouteNextHopVrfId		1.3.6.1.4.1.2272.1.8.103.2.1.12
Used to indicate nhVrfId in inter-VRF static-route configuration
Status: current	Access: read-write
OBJECT-TYPE
	VrfIdentifier

rcIpStaticMRoute		1.3.6.1.4.1.2272.1.8.105
OBJECT IDENTIFIER

rcIpStaticMRouteMib		1.3.6.1.4.1.2272.1.8.105.1
OBJECT IDENTIFIER

rcIpStaticMRouteNotifications		1.3.6.1.4.1.2272.1.8.105.1.0
OBJECT IDENTIFIER

rcIpStaticMRouteObjects		1.3.6.1.4.1.2272.1.8.105.1.1
OBJECT IDENTIFIER

rcIpStaticMRouteTable		1.3.6.1.4.1.2272.1.8.105.1.1.1
This table is used by multicast routing protocols, i.e PIM-SM, PIM-SSM, MSDP and is not visible to any other L2/L3 Protocols. It provides the flexibility of separating the paths for unicast and multicast streams. Any route addition to this table will not affect the switching and/or routing of IP unicast packets.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpStaticMRouteEntry

rcIpStaticMRouteEntry		1.3.6.1.4.1.2272.1.8.105.1.1.1.1
A static MRoute to a particular destination.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpStaticMRouteEntry

rcIpStaticMRouteIpAddressType		1.3.6.1.4.1.2272.1.8.105.1.1.1.1.1
The address type of Static MRoute IP address.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddressType

rcIpStaticMRouteIpAddress		1.3.6.1.4.1.2272.1.8.105.1.1.1.1.2
Static MRoute IP address denotes the destination network for which the route is being added.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddress

rcIpStaticMRouteMask		1.3.6.1.4.1.2272.1.8.105.1.1.1.1.3
Denotes the IP subnet mask of the Static MRoute.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddressPrefixLength

rcIpStaticMRouteRpfAddressType		1.3.6.1.4.1.2272.1.8.105.1.1.1.1.4
The address type of Static MRoute Rpf address.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddressType

rcIpStaticMRouteRpfAddress		1.3.6.1.4.1.2272.1.8.105.1.1.1.1.5
RPF address is the same as the nexthop in unicast Static IP route table. The RPF address denotes the RPF neighbor towards RP/Source.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddress

rcIpStaticMRoutePreference		1.3.6.1.4.1.2272.1.8.105.1.1.1.1.6
Static MRoute Preference is the administrative distance for the given route. When unicast routing table and the multicast-static IP route table have different routes for the same destination network, then this administrative distance is compared with that of the protocol that contributed the route in unicast routing table. By providing administrative distance for every route, we are giving flexibility to the administrator to choose different distances for different networks.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	1..255

rcIpStaticMRouteEnable		1.3.6.1.4.1.2272.1.8.105.1.1.1.1.7
This denotes the status of the route in this table. It can either be enabled/disabled.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcIpStaticMRouteRowStatus		1.3.6.1.4.1.2272.1.8.105.1.1.1.1.8
Creation and deletion of the row entry.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcIpEcmp		1.3.6.1.4.1.2272.1.8.106
OBJECT IDENTIFIER

rcIpEcmpMib		1.3.6.1.4.1.2272.1.8.106.1
OBJECT IDENTIFIER

rcIpEcmpObjects		1.3.6.1.4.1.2272.1.8.106.1.1
OBJECT IDENTIFIER

rcIpEcmpRouteTable		1.3.6.1.4.1.2272.1.8.106.1.1.1
This is used to get the ECMP route for a given pair of source IP and destination IP addresses.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpEcmpRouteEntry

rcIpEcmpRouteEntry		1.3.6.1.4.1.2272.1.8.106.1.1.1.1
An entry of rcIpEcmpRouteTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpEcmpRouteEntry

rcIpEcmpRouteSrcIp		1.3.6.1.4.1.2272.1.8.106.1.1.1.1.1
Source IP
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rcIpEcmpRouteDstIp		1.3.6.1.4.1.2272.1.8.106.1.1.1.1.2
Destination IP
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rcIpEcmpRouteDstMask		1.3.6.1.4.1.2272.1.8.106.1.1.1.1.3
Destination IP mask
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rcIpEcmpRouteNextHopLegacy		1.3.6.1.4.1.2272.1.8.106.1.1.1.1.4
Next-hop address if the ingress port is on a legacy card.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIpEcmpRouteNextHopRMod		1.3.6.1.4.1.2272.1.8.106.1.1.1.1.5
Next-hop address if the ingress port is on a R-Mod card.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIPClearIPMCRecordTable		1.3.6.1.4.1.2272.1.8.108
Table used to clear an IP MC Record.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIPClearIPMCRecordEntry

rcIPClearIPMCRecordEntry		1.3.6.1.4.1.2272.1.8.108.1
IP Clear IP MC Record Table Entry
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIPClearIPMCRecordEntry

rcIPClearIPMCRecordGroup		1.3.6.1.4.1.2272.1.8.108.1.1
The IP Multicast Group Address.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rcIPClearIPMCRecordVlanId		1.3.6.1.4.1.2272.1.8.108.1.2
Vlan Id where the IP MC record has to be cleared.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..4094

rcIPClearIPMCRecordSource		1.3.6.1.4.1.2272.1.8.108.1.3
The Source IP Address.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcIPClearIPMCRecordLCForceDelete		1.3.6.1.4.1.2272.1.8.108.1.4
By default, when LCForceDelete (Line Card Force Delete) is set to false, if the IP MC record is not found on the CP, then no message will be sent to the line-card. When LCForceDelete is set to true, a message will be sent to the line-card even when the IP MC record is not found on the CP.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIPClearArpRecordTable		1.3.6.1.4.1.2272.1.8.107
Table used to clear an IP ARP Record.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIPClearArpRecordEntry

rcIPClearArpRecordEntry		1.3.6.1.4.1.2272.1.8.107.1
IP Clear ARP Record Table Entry
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIPClearArpRecordEntry

rcIPClearArpRecordIpAddr		1.3.6.1.4.1.2272.1.8.107.1.1
IP Address that needs to be cleared.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rcIPClearArpRecordVlanId		1.3.6.1.4.1.2272.1.8.107.1.2
Vlan Id where the ARP record has to be cleared.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..4094

rcIPClearArpRecordLCForceDelete		1.3.6.1.4.1.2272.1.8.107.1.3
By default, when LCForceDelete (Line Card Force Delete) is set to false, if the ARP record is not found on the CP, then no message will be sent to the line-card. When LCForceDelete is set to true, a message will be sent to the line-card even when the ARP record is not found on the CP.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpMulticastSquareSmlt		1.3.6.1.4.1.2272.1.8.109
OBJECT IDENTIFIER

rcIpMulticastSquareSmltEnable		1.3.6.1.4.1.2272.1.8.109.1
Enable/Disable multicast Square Smlt.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcArpExtLifeTime		1.3.6.1.4.1.2272.1.9.1
The lifetime in minutues of an ARP entry within the system.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcArpExtTable		1.3.6.1.4.1.2272.1.9.2
ARP extension table. This table augments the standard ipNetToMediaTable defined in RFC1213.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcArpExtEntry

rcArpExtEntry		1.3.6.1.4.1.2272.1.9.2.1
Entry containing Proprietary ARP information. An entry is automatically created in this table when an ip address is configured on an interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcArpExtEntry

rcArpExtEntIfIndex		1.3.6.1.4.1.2272.1.9.2.1.1
The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcArpExtEntDoProxy		1.3.6.1.4.1.2272.1.9.2.1.2
Enable or disable ARP proxy responses on the specified interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

rcArpExtEntDoResp		1.3.6.1.4.1.2272.1.9.2.1.3
Enable or disable the sending of ARP responses on the specified interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

rcArpExtEntDoFlood		1.3.6.1.4.1.2272.1.9.2.1.4
Enable or disable flooding of ARP responses for NLBS Virtual Mac on the specified interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

rcArpExtV2Table		1.3.6.1.4.1.2272.1.9.3
ARP extension table. This table augments the standard ipNetToMediaTable defined in RFC1213.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcArpExtV2Entry

rcArpExtV2Entry		1.3.6.1.4.1.2272.1.9.3.1
Entry containing Proprietary ARP information. An entry is automatically created in this table when an ip address is configured on an interface.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	RcArpExtV2Entry

rcArpExtV2EntIfIndex		1.3.6.1.4.1.2272.1.9.3.1.1
The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
Status: deprecated	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcArpExtV2EntIpIfAddr		1.3.6.1.4.1.2272.1.9.3.1.2
Ip Address
Status: deprecated	Access: read-only
OBJECT-TYPE
	IpAddress

rcArpExtV2EntDoProxy		1.3.6.1.4.1.2272.1.9.3.1.3
Enable or disable ARP proxy responses on the specified interface.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

rcArpExtV2EntDoResp		1.3.6.1.4.1.2272.1.9.3.1.4
Enable or disable the sending of ARP responses on the specified interface.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

rcRipExtOperation		1.3.6.1.4.1.2272.1.10.1
Enable or disable the operation of RIP on all Interfaces.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

rcRipExtUpdateTime		1.3.6.1.4.1.2272.1.10.2
The time between transmission of RIP updates on all interfaces.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcRipExtTable		1.3.6.1.4.1.2272.1.10.3
RIP extension table. This table augments the standard IfConfTable table in RFC1389.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcRipExtEntry

rcRipExtEntry		1.3.6.1.4.1.2272.1.10.3.1
Entry containing Proprietary RIP information. An entry is automatically created in this table when an ip address is configured on an interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcRipExtEntry

rcRipExtEntIfIndex		1.3.6.1.4.1.2272.1.10.3.1.1
The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcRipExtEntTalk		1.3.6.1.4.1.2272.1.10.3.1.2
Enable or disable RIP transmission on the specified interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

rcRipExtEntListen		1.3.6.1.4.1.2272.1.10.3.1.3
Enable or disable RIP reception on the specified interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

rcRipExtEntPoison		1.3.6.1.4.1.2272.1.10.3.1.4
Enable or disable operation of poison reverse on the specified interface. If poison is disabled, split-horizon operation is enabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

rcRipExtV2Table		1.3.6.1.4.1.2272.1.10.4
RIP extension table. This table augments the standard IfConfTable table in RFC1389.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcRipExtV2Entry

rcRipExtV2Entry		1.3.6.1.4.1.2272.1.10.4.1
Entry containing Proprietary RIP information. An entry is automatically created in this table when an ip address is configured on an interface.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	RcRipExtV2Entry

rcRipExtV2EntIfIndex		1.3.6.1.4.1.2272.1.10.4.1.1
The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
Status: deprecated	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcRipExtV2EntIpIfAddr		1.3.6.1.4.1.2272.1.10.4.1.2
Ip Address.
Status: deprecated	Access: read-only
OBJECT-TYPE
	IpAddress

rcRipExtV2EntTalk		1.3.6.1.4.1.2272.1.10.4.1.3
Enable or disable RIP transmission on the specified interface.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

rcRipExtV2EntListen		1.3.6.1.4.1.2272.1.10.4.1.4
Enable or disable RIP reception on the specified interface.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

rcRipExtV2EntPoison		1.3.6.1.4.1.2272.1.10.4.1.5
Enable or disable operation of poison reverse on the specified interface. If poison is disabled, split-horizon operation is enabled.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

rcTestExtTable		1.3.6.1.4.1.2272.1.11.1
Test extension table. This table augments the standard ifTestTable table in RFC1573.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcTestEntry

rcTestEntry		1.3.6.1.4.1.2272.1.11.1.1
Proprietary test variables.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcTestEntry

rcTestExtIfIndex		1.3.6.1.4.1.2272.1.11.1.1.1
The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcTestExtPassCount		1.3.6.1.4.1.2272.1.11.1.1.2
The number of iterations of the test case that completed successfully.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcTestExtFailCount		1.3.6.1.4.1.2272.1.11.1.1.3
The number of iterations of the test case that failed.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcTestTypes		1.3.6.1.4.1.2272.1.11.2
OBJECT IDENTIFIER

rcTestTypesFabric		1.3.6.1.4.1.2272.1.11.2.1
OBJECT IDENTIFIER

rcTestTypesArTable		1.3.6.1.4.1.2272.1.11.2.2
OBJECT IDENTIFIER

rcTestTypesExtLoopBack		1.3.6.1.4.1.2272.1.11.2.3
OBJECT IDENTIFIER

rcTestCodes		1.3.6.1.4.1.2272.1.11.3
OBJECT IDENTIFIER

rcTestCodesNoReceive		1.3.6.1.4.1.2272.1.11.3.1
OBJECT IDENTIFIER

rcTestCodesBadSeq		1.3.6.1.4.1.2272.1.11.3.2
OBJECT IDENTIFIER

rcTestCodesBadLen		1.3.6.1.4.1.2272.1.11.3.3
OBJECT IDENTIFIER

rcTestCodesBadData		1.3.6.1.4.1.2272.1.11.3.4
OBJECT IDENTIFIER

rcStatTable		1.3.6.1.4.1.2272.1.12.1
A table used to store port statistics.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcStatEntry

rcStatEntry		1.3.6.1.4.1.2272.1.12.1.1
interface counters
Status: current	Access: not-accessible
OBJECT-TYPE
	RcStatEntry

rcStatPortIndex		1.3.6.1.4.1.2272.1.12.1.1.1
An index value that uniquely identifies a port. This value is similar to ifIndex in MIB2.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcStatFrameTooShorts		1.3.6.1.4.1.2272.1.12.1.1.2
The total number of frames that are too short that were encountered on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBridgeInUnicastFrames		1.3.6.1.4.1.2272.1.12.1.1.3
The total number of incoming unicast frames that were bridged.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBridgeInMulticastFrames		1.3.6.1.4.1.2272.1.12.1.1.4
The total number of incoming multicast frames that were bridged.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBridgeInBroadcastFrames		1.3.6.1.4.1.2272.1.12.1.1.5
The total number of incoming broadcast frames that were bridged.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBridgeInDiscards		1.3.6.1.4.1.2272.1.12.1.1.6
The total number of frames that were discarded by the bridging entity.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBridgeOutUnicastFrames		1.3.6.1.4.1.2272.1.12.1.1.7
The total number of outgoing unicast frames that were bridged.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBridgeOutMulticastFrames		1.3.6.1.4.1.2272.1.12.1.1.8
The total number of outgoing multicast frames that were bridged.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBridgeOutBroadcastFrames		1.3.6.1.4.1.2272.1.12.1.1.9
The total number of outgoing broadcast frames that were bridged.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatRouteInUnicastFrames		1.3.6.1.4.1.2272.1.12.1.1.10
The total number of incoming unicast frames that were routed.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatRouteInMulticastFrames		1.3.6.1.4.1.2272.1.12.1.1.11
The total number of incoming multicast frames that were routed.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatRouteInDiscards		1.3.6.1.4.1.2272.1.12.1.1.12
The total number of frames that were discarded by the routing entity.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatRouteOutUnicastFrames		1.3.6.1.4.1.2272.1.12.1.1.13
The total number of outgoing unicast frames that were routed.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatRouteOutMulticastFrames		1.3.6.1.4.1.2272.1.12.1.1.14
The total number of outgoing multicast frames that were routed.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatStgForwardTransitions		1.3.6.1.4.1.2272.1.12.1.1.15
The number of times this port has transitioned from the Learning state to the Forwarding state.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatStgInConfigBpdus		1.3.6.1.4.1.2272.1.12.1.1.16
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatStgInTcnBpdus		1.3.6.1.4.1.2272.1.12.1.1.17
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatStgInBadBpdus		1.3.6.1.4.1.2272.1.12.1.1.18
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatStgOutConfigBpdus		1.3.6.1.4.1.2272.1.12.1.1.19
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatStgOutTcnBpdus		1.3.6.1.4.1.2272.1.12.1.1.20
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBridgeOutFrames		1.3.6.1.4.1.2272.1.12.1.1.21
Used by the Accelar 8000 product family to account for all transmitted bridge unicast, broadcast, and multicast packets. The individual counters are not supported.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatGigTable		1.3.6.1.4.1.2272.1.12.2
A table used to store Gigport error statistics.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcStatGigEntry

rcStatGigEntry		1.3.6.1.4.1.2272.1.12.2.1
Gigabit interface error counters
Status: current	Access: not-accessible
OBJECT-TYPE
	RcStatGigEntry

rcStatGigPortIndex		1.3.6.1.4.1.2272.1.12.2.1.1
An index value that uniquely identifies a port. This value is similar to ifIndex in MIB2.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcStatGigLinkFailures		1.3.6.1.4.1.2272.1.12.2.1.2
The total number of link failures encountered on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatGigPacketErrors		1.3.6.1.4.1.2272.1.12.2.1.3
The total number of packet errors encountered on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatGigCarrierErrors		1.3.6.1.4.1.2272.1.12.2.1.4
The total number of carrier errors encountered on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatGigLinkInactiveErrors		1.3.6.1.4.1.2272.1.12.2.1.5
The total number of link inactive errors encountered on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatGigInFlowCtrlPkts		1.3.6.1.4.1.2272.1.12.2.1.6
The total number of flow control packets received by this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatGigOutFlowCtrlPkts		1.3.6.1.4.1.2272.1.12.2.1.7
The total number of flow control packets transmitted by this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspf		1.3.6.1.4.1.2272.1.12.3
OBJECT IDENTIFIER

rcStatOspfBuffersAllocated		1.3.6.1.4.1.2272.1.12.3.1
Used to indicate the number of buffers allocated for OSPF.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfBuffersFreed		1.3.6.1.4.1.2272.1.12.3.2
Used to indicate the number of buffers that are freed by the OSPF.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfBufferAllocFailures		1.3.6.1.4.1.2272.1.12.3.3
Used to indicate the number of times that OSPF has failed to allocate buffers.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfBufferFreeFailures		1.3.6.1.4.1.2272.1.12.3.4
Used to indicate the number of times that OSPF has failed to free buffers.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfTxPackets		1.3.6.1.4.1.2272.1.12.3.5
Used to indicate the number of packets transmitted by OSPF.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfRxPackets		1.3.6.1.4.1.2272.1.12.3.6
Used to indicate the number of packets received by OSPF.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfTxDropPackets		1.3.6.1.4.1.2272.1.12.3.7
Used to indicate the number of packets dropped before transmitted by OSPF.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfRxDropPackets		1.3.6.1.4.1.2272.1.12.3.8
Used to indicate the number of packets dropped before received by OSPF.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfRxBadPackets		1.3.6.1.4.1.2272.1.12.3.9
Used to indicate the number of packets received by OSPF that are bad.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfSpfRuns		1.3.6.1.4.1.2272.1.12.3.10
Used to indicate the total number of SPF calculatations performed by OSPF, which also includes the number of partial route table calculation for Incremental Updates.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfLastSpfRun		1.3.6.1.4.1.2272.1.12.3.11
Used to indicate the time(SysUpTime) since the last spf calculated by OSPF.
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

rcStatOspfLsdbTblSize		1.3.6.1.4.1.2272.1.12.3.12
Used to indicate the number of entries in the linkstate database table.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfRoutes		1.3.6.1.4.1.2272.1.12.3.13
Used to indicate the number of OSPF routes added to RTM.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfAdjacencies		1.3.6.1.4.1.2272.1.12.3.14
Used to indicate the number of adjacencies existing.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfAreas		1.3.6.1.4.1.2272.1.12.3.15
Used to indicate the number of areas configured
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatIgmp		1.3.6.1.4.1.2272.1.12.4
OBJECT IDENTIFIER

rcStatIgmpInMsgs		1.3.6.1.4.1.2272.1.12.4.1
Used to indicate the number of Igmp packets received by the device.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatIgmpInErrors		1.3.6.1.4.1.2272.1.12.4.2
Used to indicate the number of Igmp packets received that are with checksum errors.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatIgmpInQueries		1.3.6.1.4.1.2272.1.12.4.3
Used to indicate the number of Igmp queries received by the device.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatIgmpInReports		1.3.6.1.4.1.2272.1.12.4.4
Used to indicate the number of Igmp reports received by the device.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatIgmpInLeaves		1.3.6.1.4.1.2272.1.12.4.5
Used to indicate the number of Igmp Leaves received by the device.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatIgmpInvalid		1.3.6.1.4.1.2272.1.12.4.6
Used to indicate the number of Igmp packets received by the device that contained invalid type.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatIgmpOutMsgs		1.3.6.1.4.1.2272.1.12.4.7
Used to indicate the number of Igmp queries sent by the device.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfIfTable		1.3.6.1.4.1.2272.1.12.5
A table used to store OSPF interface statistics.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcStatOspfIfEntry

rcStatOspfIfEntry		1.3.6.1.4.1.2272.1.12.5.1
Ospf interface statistics
Status: current	Access: not-accessible
OBJECT-TYPE
	RcStatOspfIfEntry

rcStatOspfIfIndex		1.3.6.1.4.1.2272.1.12.5.1.1
An unique value that is used to identify a physical interface.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndexOrZero	0..6142

rcStatOspfIfRxHellos		1.3.6.1.4.1.2272.1.12.5.1.2
Used to indicate the number hello packets received by this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfIfRxDBDescrs		1.3.6.1.4.1.2272.1.12.5.1.3
Used to indicate the number database descriptor packets received by this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfIfRxLSUpdates		1.3.6.1.4.1.2272.1.12.5.1.4
Used to indicate the number Link state update packets received by this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfIfRxLSReqs		1.3.6.1.4.1.2272.1.12.5.1.5
Used to indicate the number Link state request packets received by this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfIfRxLSAcks		1.3.6.1.4.1.2272.1.12.5.1.6
Used to indicate the number Link state acknowlege packets received by this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfIfTxHellos		1.3.6.1.4.1.2272.1.12.5.1.7
Used to indicate the number hello packets transmitted by this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfIfTxDBDescrs		1.3.6.1.4.1.2272.1.12.5.1.8
Used to indicate the number database descriptor packets transmitted by this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfIfTxLSUpdates		1.3.6.1.4.1.2272.1.12.5.1.9
Used to indicate the number Link state update packets transmitted by this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfIfTxLSReqs		1.3.6.1.4.1.2272.1.12.5.1.10
Used to indicate the number Link state request packets transmitted by this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfIfTxLSAcks		1.3.6.1.4.1.2272.1.12.5.1.11
Used to indicate the number Link state acknowlege packets transmitted by this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfIfVersionMismatches		1.3.6.1.4.1.2272.1.12.5.1.12
Used to indicate the number version mismatches received by this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfIfAreaMismatches		1.3.6.1.4.1.2272.1.12.5.1.13
Used to indicate the number area mismatches received by this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfIfAuthTypeMismatches		1.3.6.1.4.1.2272.1.12.5.1.14
Used to indicate the number AuthType mismatches received by this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfIfAuthFailures		1.3.6.1.4.1.2272.1.12.5.1.15
Used to indicate the number Authentication failures.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfIfNetMaskMismatches		1.3.6.1.4.1.2272.1.12.5.1.16
Used to indicate the number net mask mismatches received by this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfIfHelloIntervalMismatches		1.3.6.1.4.1.2272.1.12.5.1.17
Used to indicate the number hello interval mismatches received by this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfIfDeadIntervalMismatches		1.3.6.1.4.1.2272.1.12.5.1.18
Used to indicate the number dead interval mismatches received by this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfIfOptionMismatches		1.3.6.1.4.1.2272.1.12.5.1.19
Used to indicate the number options mismatches received by this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatMlt		1.3.6.1.4.1.2272.1.12.6
OBJECT IDENTIFIER

rcStatMltIfExtnTable		1.3.6.1.4.1.2272.1.12.6.1
A table used to store Mlt interface statistics.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcStatMltIfExtnEntry

rcStatMltIfExtnEntry		1.3.6.1.4.1.2272.1.12.6.1.1
Mlt interface statistics
Status: current	Access: not-accessible
OBJECT-TYPE
	RcStatMltIfExtnEntry

rcStatMltIfExtnMltId		1.3.6.1.4.1.2272.1.12.6.1.1.1
Mlt Id
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..256

rcStatMltIfExtnIfInMulticastPkts		1.3.6.1.4.1.2272.1.12.6.1.1.2
multi-pkts to upper
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatMltIfExtnIfInBroadcastPkts		1.3.6.1.4.1.2272.1.12.6.1.1.3
broad-pkts to upper
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatMltIfExtnIfOutMulticastPkts		1.3.6.1.4.1.2272.1.12.6.1.1.4
multi-pkts from upper
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatMltIfExtnIfOutBroadcastPkts		1.3.6.1.4.1.2272.1.12.6.1.1.5
broad-pkts from upper
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatMltIfExtnIfHCInOctets		1.3.6.1.4.1.2272.1.12.6.1.1.6
The total number of octets received on the MLT interface, including framing characters.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcStatMltIfExtnIfHCInUcastPkts		1.3.6.1.4.1.2272.1.12.6.1.1.7
The number of packets delivered by this MLT to a higher MLT that were not addressed to a nulticast or broadcase address at this sublayer.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcStatMltIfExtnIfHCInMulticastPkt		1.3.6.1.4.1.2272.1.12.6.1.1.8
The number of packets delivered to this MLT that were addressed to a nulticast address at this sublayer. For a MAC layer protocol, this number includes both Group and Functional addresses.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcStatMltIfExtnIfHCInBroadcastPkt		1.3.6.1.4.1.2272.1.12.6.1.1.9
The number of packets delivered to this MLT that were addressed to a broadcast address at this sublayer.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcStatMltIfExtnIfHCOutOctets		1.3.6.1.4.1.2272.1.12.6.1.1.10
The total number of octets transmitted out of the MLT interface, including framing characters.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcStatMltIfExtnIfHCOutUcastPkts		1.3.6.1.4.1.2272.1.12.6.1.1.11
The number of packets that hight-level protocols requested be transmitted that were not addressed to a multicast address at this MLT. This total number includes those packets discarded or unsent.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcStatMltIfExtnIfHCOutMulticast		1.3.6.1.4.1.2272.1.12.6.1.1.12
The total number of packets that hight-level protocols requested be transmitted, and that were addressed to a multicast address at this MLT, including those that were discarded or not sent. For a MAC layer protocol, this number includes both Group and Functional addresses.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcStatMltIfExtnIfHCOutBroadcast		1.3.6.1.4.1.2272.1.12.6.1.1.13
The total number of packets that hight-level protocols requested be transmitted, and that were addressed to a broadcase address at this MLT, including those that were discarded or not sent.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcStatMltEtherTable		1.3.6.1.4.1.2272.1.12.6.2
A table used to store Mlt Ethernet statistics.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcStatMltEtherEntry

rcStatMltEtherEntry		1.3.6.1.4.1.2272.1.12.6.2.1
Mlt enternet statistics
Status: current	Access: not-accessible
OBJECT-TYPE
	RcStatMltEtherEntry

rcStatMltEtherMltId		1.3.6.1.4.1.2272.1.12.6.2.1.1
A value that uniquely identifies the Multi-Link Trunk associated with this entry.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..256

rcStatMltEtherAlignmentErrors		1.3.6.1.4.1.2272.1.12.6.2.1.2
A count of frames received on a particular MLT that are not an integral number of octets in length and do not pass the FCS check. The count represented by an instance of this object is incremented when the alignmentError status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions occur are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatMltEtherFCSErrors		1.3.6.1.4.1.2272.1.12.6.2.1.3
A count of frames received on an MLT that are an integral number of octets in length but do not pass the FCS check. The count represented by an instance of this object is incremented when the frameCheckError status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions occur are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatMltEtherSingleCollFrames		1.3.6.1.4.1.2272.1.12.6.2.1.4
A count of successfully transmitted frames on a particular MLT for which transmission is inhibited by exactly one collision. A frame that is counted by an instance of this objects is also counted by the corresponding instance of either the ifOutUcastPkts, ifOutMulticastPkts, or ifOutBroadcastPkts, and it not counted by the corresponding instance of the MultipleCollisionFrames object.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatMltEtherMultipleCollFrames		1.3.6.1.4.1.2272.1.12.6.2.1.5
A count of successfully transmitted frames on a particular MLT for which transmission is inhibited by more than one collision. A frame that is counted by an instance of this object is also counted by the corresponding instance of either the ifOutUcastPkts, ifOutMulticastPkts, or ifOutBroadcastPkts, and is not counted by the corresponding instance of the SingleCollisionFrames objects.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatMltEtherSQETestError		1.3.6.1.4.1.2272.1.12.6.2.1.6
A count of times that the SQE TEST ERROR message is generated by the PLS sublayer for a particular MLT. SQE stands for Signal Quality Error.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatMltEtherDeferredTransmiss		1.3.6.1.4.1.2272.1.12.6.2.1.7
A count of frames for which the first transmission attempt on a particular MLT is delayed because the medium is busy. The count represented by an instance of this object does not include frames involved in collisions.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatMltEtherLateCollisions		1.3.6.1.4.1.2272.1.12.6.2.1.8
The number of times that a collision is detected on a particular MLT later than 512 bit-times (64 octets) into the transmission of a packet. Five hundred and twelve bit-times corresponds to 51.2 microseconds on a 10 mb/s system. A (late) collision included in a count represented by an instance of this object is also considered as a (generic) collision for purposes of other collision-related statistics.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatMltEtherExcessiveCollis		1.3.6.1.4.1.2272.1.12.6.2.1.9
A count of frames for which transmission on a particular MLT fails due to excessive collisions.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatMltEtherIMacTransmitError		1.3.6.1.4.1.2272.1.12.6.2.1.10
A count of frames for which transmission on a particular MLT fails due to an internal MAC sublayer transmit error. A frame is only counted by an instance of this object if it is not counted by the corresponding instance of either the LateCollisions object, the ExcessiveCollisions object, or the CarrierSenseError object.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatMltEtherCarrierSenseError		1.3.6.1.4.1.2272.1.12.6.2.1.11
The number of times that the carrier sense condition was lost or never asserted when attempting to transmit a frame on a particular MLT. The count represented by an instance of this object is incremented at most once per transmission attempt, even if the carrier sense condition fluctuates during a transmission attempt.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatMltEtherFrameTooLong		1.3.6.1.4.1.2272.1.12.6.2.1.12
A count of frames received on a particular MLT that exceed the maximum permitted size (1518 octets). The count represented by an instance os this object is incremented when the frame TooLong status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions occur are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatMltEtherIMacReceiveError		1.3.6.1.4.1.2272.1.12.6.2.1.13
A count of frames for which reception on a particular MLT fails due to an internal MAC sublayer receive error. A frame is only counted by an instance of this object if it is not counted by the corresponding instance of either the FrameTooLongs object, the AlignmentErrors object, of the FCSErrors objects. The precise meaning of the count represented by an instance of this object is implementation specific. In particular, an instance of this object may represent a count of receive errors on a particular interface that are not otherwise counted.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatMltIpTable		1.3.6.1.4.1.2272.1.12.6.3
A table used to store Mlt Ip statistics.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcStatMltIpEntry

rcStatMltIpEntry		1.3.6.1.4.1.2272.1.12.6.3.1
Mlt enternet statistics
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	RcStatMltIpEntry

rcStatMltIpMltId		1.3.6.1.4.1.2272.1.12.6.3.1.1
Mlt Id
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	1..8

rcStatMltIpInReceives		1.3.6.1.4.1.2272.1.12.6.3.1.2
all incoming packets
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcStatMltIpInHdrErrors		1.3.6.1.4.1.2272.1.12.6.3.1.3
hdr errors detected
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcStatMltIpInAddrErrors		1.3.6.1.4.1.2272.1.12.6.3.1.4
bad dest. ip addr
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcStatMltIpForwDatagrams		1.3.6.1.4.1.2272.1.12.6.3.1.5
packets forwarded
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcStatMltIpInUnknownProtos		1.3.6.1.4.1.2272.1.12.6.3.1.6
unsupported protocol
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcStatMltIpInDiscards		1.3.6.1.4.1.2272.1.12.6.3.1.7
good, but no buffer
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcStatMltIpInDelivers		1.3.6.1.4.1.2272.1.12.6.3.1.8
pkts delivered to upper
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcStatMltIpOutRequest		1.3.6.1.4.1.2272.1.12.6.3.1.9
pkts received from upper
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcStatMltIpOutDiscards		1.3.6.1.4.1.2272.1.12.6.3.1.10
good, but no buffer
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcStatMltIpOutNoRoutes		1.3.6.1.4.1.2272.1.12.6.3.1.11
no route to destination
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcStatMltIpReasmReqds		1.3.6.1.4.1.2272.1.12.6.3.1.12
fragments to reassem
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcStatMltIpReasmOKs		1.3.6.1.4.1.2272.1.12.6.3.1.13
reassembled successfully
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcStatMltIpReasmFails		1.3.6.1.4.1.2272.1.12.6.3.1.14
reassembly failures
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcStatMltIpFragOKs		1.3.6.1.4.1.2272.1.12.6.3.1.15
fragment successfully
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcStatMltIpFragFails		1.3.6.1.4.1.2272.1.12.6.3.1.16
fragment failure
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcStatMltIpFragCreates		1.3.6.1.4.1.2272.1.12.6.3.1.17
pkts due to fragmenting
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcStatMltIpRoutingDiscards		1.3.6.1.4.1.2272.1.12.6.3.1.18
Route entries removed
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcStatSmltIstDownCnt		1.3.6.1.4.1.2272.1.12.6.4
Counters that counts how the session between the two peering switches has done down since last boot.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatSmltHelloTxMsgCnt		1.3.6.1.4.1.2272.1.12.6.5
Counters that counts the tx hello msg.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatSmltHelloRxMsgCnt		1.3.6.1.4.1.2272.1.12.6.6
Counters that counts the rx hello msg.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatSmltLearnMacAddrTxMsgCnt		1.3.6.1.4.1.2272.1.12.6.7
Counters that counts the tx learn Mac Address msg.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatSmltLearnMacAddrRxMsgCnt		1.3.6.1.4.1.2272.1.12.6.8
Counters that counts the rx learn Mac Address msg.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatSmltMacAddrAgeOutTxMsgCnt		1.3.6.1.4.1.2272.1.12.6.9
Counters that counts the tx Mac Address Aging Out msg.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatSmltMacAddrAgeOutRxMsgCnt		1.3.6.1.4.1.2272.1.12.6.10
Counters that counts the rx Mac Address Aging Out msg.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatSmltMacAddrAgeExpTxMsgCnt		1.3.6.1.4.1.2272.1.12.6.11
Counters that counts the tx Mac Address age expired msg.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatSmltMacAddrAgeExpRxMsgCnt		1.3.6.1.4.1.2272.1.12.6.12
Counters that counts the rx Mac Address age expired msg.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatSmltStgInfoTxMsgCnt		1.3.6.1.4.1.2272.1.12.6.13
Counters that counts the tx Stg information msg.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatSmltStgInfoRxMsgCnt		1.3.6.1.4.1.2272.1.12.6.14
Counters that counts the rx Stg information msg.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatSmltDelMacAddrTxMsgCnt		1.3.6.1.4.1.2272.1.12.6.15
Counters that counts the tx deleted MAC address msg.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatSmltDelMacAddrRxMsgCnt		1.3.6.1.4.1.2272.1.12.6.16
Counters that counts the rx deleted MAC address msg.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatSmltSmltDownTxMsgCnt		1.3.6.1.4.1.2272.1.12.6.17
Counters that counts the tx Smlt Down msg.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatSmltSmltDownRxMsgCnt		1.3.6.1.4.1.2272.1.12.6.18
Counters that counts the rx Smlt Down msg.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatSmltSmltUpTxMsgCnt		1.3.6.1.4.1.2272.1.12.6.19
Counters that counts the tx Smlt Up msg.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatSmltSmltUpRxMsgCnt		1.3.6.1.4.1.2272.1.12.6.20
Counters that counts the rx Smlt Up msg.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatSmltSendMacTblTxMsgCnt		1.3.6.1.4.1.2272.1.12.6.21
Counters that counts the tx Send Mac Table msg.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatSmltSendMacTblRxMsgCnt		1.3.6.1.4.1.2272.1.12.6.22
Counters that counts the rx Send Mac Table msg.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatSmltIgmpTxMsgCnt		1.3.6.1.4.1.2272.1.12.6.23
Counters that counts the tx Igmp msg.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatSmltIgmpRxMsgCnt		1.3.6.1.4.1.2272.1.12.6.24
Counters that counts the rx Igmp msg.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatSmltPortDownTxMsgCnt		1.3.6.1.4.1.2272.1.12.6.25
Counters that counts the tx port down msg.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatSmltPortDownRxMsgCnt		1.3.6.1.4.1.2272.1.12.6.26
Counters that counts the rx port down msg.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatSmltReqMacTblTxMsgCnt		1.3.6.1.4.1.2272.1.12.6.27
Counters that counts the tx request Mac table msg.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatSmltReqMacTblRxMsgCnt		1.3.6.1.4.1.2272.1.12.6.28
Counters that counts the rx request Mac table msg.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatSmltRxUnknownMsgTypeCnt		1.3.6.1.4.1.2272.1.12.6.29
Counters that counts the rx unknown msg type.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfIfV2Table		1.3.6.1.4.1.2272.1.12.7
A table used to store OSPF interface statistics.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcStatOspfIfV2Entry

rcStatOspfIfV2Entry		1.3.6.1.4.1.2272.1.12.7.1
Ospf interface statistics
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	RcStatOspfIfV2Entry

rcStatOspfIfV2Index		1.3.6.1.4.1.2272.1.12.7.1.1
An unique value that is used to identify a physical interface.
Status: deprecated	Access: read-only
OBJECT-TYPE
	InterfaceIndexOrZero	0..6142

rcStatOspfIfV2Addr		1.3.6.1.4.1.2272.1.12.7.1.2
Ip Address
Status: deprecated	Access: read-only
OBJECT-TYPE
	IpAddress

rcStatOspfIfV2RxHellos		1.3.6.1.4.1.2272.1.12.7.1.3
Used to indicate the number hello packets received by this interface.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfIfV2RxDBDescrs		1.3.6.1.4.1.2272.1.12.7.1.4
Used to indicate the number database descriptor packets received by this interface.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfIfV2RxLSUpdates		1.3.6.1.4.1.2272.1.12.7.1.5
Used to indicate the number Link state update packets received by this interface.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfIfV2RxLSReqs		1.3.6.1.4.1.2272.1.12.7.1.6
Used to indicate the number Link state request packets received by this interface.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfIfV2RxLSAcks		1.3.6.1.4.1.2272.1.12.7.1.7
Used to indicate the number Link state acknowlege packets received by this interface.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfIfV2TxHellos		1.3.6.1.4.1.2272.1.12.7.1.8
Used to indicate the number hello packets transmitted by this interface.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfIfV2TxDBDescrs		1.3.6.1.4.1.2272.1.12.7.1.9
Used to indicate the number database descriptor packets transmitted by this interface.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfIfV2TxLSUpdates		1.3.6.1.4.1.2272.1.12.7.1.10
Used to indicate the number Link state update packets transmitted by this interface.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfIfV2TxLSReqs		1.3.6.1.4.1.2272.1.12.7.1.11
Used to indicate the number Link state request packets transmitted by this interface.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfIfV2TxLSAcks		1.3.6.1.4.1.2272.1.12.7.1.12
Used to indicate the number Link state acknowlege packets transmitted by this interface.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfIfV2VersionMismatches		1.3.6.1.4.1.2272.1.12.7.1.13
Used to indicate the number version mismatches received by this interface.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfIfV2AreaMismatches		1.3.6.1.4.1.2272.1.12.7.1.14
Used to indicate the number area mismatches received by this interface.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfIfV2AuthTypeMismatches		1.3.6.1.4.1.2272.1.12.7.1.15
Used to indicate the number AuthType mismatches received by this interface.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfIfV2AuthFailures		1.3.6.1.4.1.2272.1.12.7.1.16
Used to indicate the number Authentication failures.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfIfV2NetMaskMismatches		1.3.6.1.4.1.2272.1.12.7.1.17
Used to indicate the number net mask mismatches received by this interface.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfIfV2HelloIntervalMismatches		1.3.6.1.4.1.2272.1.12.7.1.18
Used to indicate the number hello interval mismatches received by this interface.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfIfV2DeadIntervalMismatches		1.3.6.1.4.1.2272.1.12.7.1.19
Used to indicate the number dead interval mismatches received by this interface.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcStatOspfIfV2OptionMismatches		1.3.6.1.4.1.2272.1.12.7.1.20
Used to indicate the number options mismatches received by this interface.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcStatPos		1.3.6.1.4.1.2272.1.12.8
OBJECT IDENTIFIER

rcStatPosControlTable		1.3.6.1.4.1.2272.1.12.8.1
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcStatPosControlEntry

rcStatPosControlEntry		1.3.6.1.4.1.2272.1.12.8.1.1
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	RcStatPosControlEntry

rcStatPosControlPortIndex		1.3.6.1.4.1.2272.1.12.8.1.1.1
A unique value for each port.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcStatPosControlInErrors		1.3.6.1.4.1.2272.1.12.8.1.1.2
The total number of error pkts received on the interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatPosControlInUnknownProtos		1.3.6.1.4.1.2272.1.12.8.1.1.3
The number of packets received via the interface which were discarded because of an unknown or unsupported protocol.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatPosControlOutErrors		1.3.6.1.4.1.2272.1.12.8.1.1.4
The number of outbound packets that could not be transmitted because of errors.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatPosControlHCInOctets		1.3.6.1.4.1.2272.1.12.8.1.1.5
The total number of octets received of the interface, including framing characters.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcStatPosControlHCInUcastPkts		1.3.6.1.4.1.2272.1.12.8.1.1.6
The number of subnetwork-unicast packets received from a higher-layer protocol.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcStatPosControlHCInMulticastPkts		1.3.6.1.4.1.2272.1.12.8.1.1.7
The number of multicast packets received from a higher-layer protocol.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcStatPosControlHCInBroadcastPkts		1.3.6.1.4.1.2272.1.12.8.1.1.8
The number of broadcast packets received from a higher-layer protocol.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcStatPosControlHCInDiscards		1.3.6.1.4.1.2272.1.12.8.1.1.9
The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcStatPosControlHCOutOctets		1.3.6.1.4.1.2272.1.12.8.1.1.10
The total number of octets trasmitted out of the interface, including framing characters.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcStatPosControlHCOutUcastPkts		1.3.6.1.4.1.2272.1.12.8.1.1.11
The total number of packets that higher-level protocols requested be transmitted to a subnetwork-unicast address, including those that were discarded or not sent.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcStatPosControlHCOutMulticastPkts		1.3.6.1.4.1.2272.1.12.8.1.1.12
The number of multicast packets delivered to a higher-layer protocol.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcStatPosControlHCOutBroadcastPkts		1.3.6.1.4.1.2272.1.12.8.1.1.13
The number of broadcast packets delivered to a higher-layer protocol.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcStatPosControlHCOutDiscards		1.3.6.1.4.1.2272.1.12.8.1.1.14
The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcStatMulticast		1.3.6.1.4.1.2272.1.12.9
OBJECT IDENTIFIER

rcStatMulticastSourceGroupThresholdExceeded		1.3.6.1.4.1.2272.1.12.9.1
The count of number of times the threshold of available IP Multicast (Source,Group) Records was reached. When this threshold is reached, a new IP Multicast stream ingressing the switch cannot be forwarded.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatMulticastEgressStreamThresholdExceeded		1.3.6.1.4.1.2272.1.12.9.2
The count of number of times the threshold of available IP Multicast Egress Forwarding Records was reached. When this threshold is reached, a new IP Multicast Receiver that needs new Egress Forwarding Record (PepStrem Record) will not be programmed to receive the subscribing multicast stream.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgp		1.3.6.1.4.1.2272.1.12.10
OBJECT IDENTIFIER

rcStatBgpStarts		1.3.6.1.4.1.2272.1.12.10.1
Number of times BGP connection started
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpStops		1.3.6.1.4.1.2272.1.12.10.2
Number of times BGP connection stopped
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpOpens		1.3.6.1.4.1.2272.1.12.10.3
Number of times BGP opens TCP
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpCloses		1.3.6.1.4.1.2272.1.12.10.4
Number of times BGP closes TCP
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpFails		1.3.6.1.4.1.2272.1.12.10.5
Number of times TCP attempts failed
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpFatals		1.3.6.1.4.1.2272.1.12.10.6
Number of times TCP crashes due to fatal error
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpConnExps		1.3.6.1.4.1.2272.1.12.10.7
Number of times TCP retry timer expired
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpHoldExps		1.3.6.1.4.1.2272.1.12.10.8
Number of times hold timer expired
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpKeepExps		1.3.6.1.4.1.2272.1.12.10.9
Number of times keepalive timer expired
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpRxOpens		1.3.6.1.4.1.2272.1.12.10.10
Number of OPENs BGP receives
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpRxKeeps		1.3.6.1.4.1.2272.1.12.10.11
Number of KEEPALIVEs BGP recieves
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpRxUpdates		1.3.6.1.4.1.2272.1.12.10.12
Number of UPDATEs BGP recieves
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpRxNotifys		1.3.6.1.4.1.2272.1.12.10.13
Number NOTIFICATIONs BGP recieves
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpTxOpens		1.3.6.1.4.1.2272.1.12.10.14
Number of OPENs BGP transmitted
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpTxKeeps		1.3.6.1.4.1.2272.1.12.10.15
Number of KEEPALIVEs BGP transmitted
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpTxUpdates		1.3.6.1.4.1.2272.1.12.10.16
Number of UPDATEs BGP transmits
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpTxNotifys		1.3.6.1.4.1.2272.1.12.10.17
Number of NOTIFICATIONs BGP transmits
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpBadEvents		1.3.6.1.4.1.2272.1.12.10.18
Number of invalid events FSM received
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpSyncFails		1.3.6.1.4.1.2272.1.12.10.19
Number of times FDB sync failed
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpTrEvent		1.3.6.1.4.1.2272.1.12.10.20
Trace event
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpRxECodeHeader		1.3.6.1.4.1.2272.1.12.10.21
Total Header errors received
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpRxECodeOpen		1.3.6.1.4.1.2272.1.12.10.22
Total Open errors received
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpRxECodeUpdate		1.3.6.1.4.1.2272.1.12.10.23
Total Update errors received
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpRxECodeHoldtimer		1.3.6.1.4.1.2272.1.12.10.24
Total Holdtimer errors received
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpRxECodeFSM		1.3.6.1.4.1.2272.1.12.10.25
Total FSM errors received
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpRxECodeCease		1.3.6.1.4.1.2272.1.12.10.26
Total Cease errors received
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpRxHdrCodeNoSync		1.3.6.1.4.1.2272.1.12.10.27
Header Not Synchronized errors received
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpRxHdrCodeInvalidMsgLen		1.3.6.1.4.1.2272.1.12.10.28
Header Invalid msg len errors received
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpRxHdrCodeInvalidMsgType		1.3.6.1.4.1.2272.1.12.10.29
Header Invalid msg type errors received
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpRxOpCodeBadVer		1.3.6.1.4.1.2272.1.12.10.30
Open errors received: Bad Version
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpRxOpCodeBadAs		1.3.6.1.4.1.2272.1.12.10.31
Open errors received: Bad AS Number
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpRxOpCodeBadRtID		1.3.6.1.4.1.2272.1.12.10.32
Open errors received: Bad BGP Rtr ID
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpRxOpCodeUnsuppOption		1.3.6.1.4.1.2272.1.12.10.33
Open errors received: Unsupported Option
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpRxOpCodeAuthFail		1.3.6.1.4.1.2272.1.12.10.34
Open errors received: Auth Failures
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpRxOpCodeBadHold		1.3.6.1.4.1.2272.1.12.10.35
Open errors received: Bad Hold Value
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpRxUpdCodeMalformedAttrList		1.3.6.1.4.1.2272.1.12.10.36
Update errors received:Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpRxUpdCodeWelknownAttrUnrecog		1.3.6.1.4.1.2272.1.12.10.37
Update errors received: Welknown Attr Unrecog
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpRxUpdCodeWelknownAttrMiss		1.3.6.1.4.1.2272.1.12.10.38
Update errors received: Welknown Attr Missing
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpRxUpdCodeAttrFlagError		1.3.6.1.4.1.2272.1.12.10.39
Update errors received: Attr Flag Error
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpRxUpdCodeAttrLenError		1.3.6.1.4.1.2272.1.12.10.40
Update errors received: Attr Len Error
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpRxUpdCodeBadORIGINAttr		1.3.6.1.4.1.2272.1.12.10.41
Update errors received: Bad ORIGIN Attr
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpRxUpdCodeASRoutingLoop		1.3.6.1.4.1.2272.1.12.10.42
Update errors received: AS Routing Loop
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpRxUpdCodeBadNHAttr		1.3.6.1.4.1.2272.1.12.10.43
Update errors received: Bad NEXT-HOP Attr
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpRxUpdCodeOptionalAttrError		1.3.6.1.4.1.2272.1.12.10.44
Update errors received: Optional Attr Error
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpRxUpdCodeBadNetworkField		1.3.6.1.4.1.2272.1.12.10.45
Update errors received: Bad Network Field
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpRxUpdCodeMalformedASPath		1.3.6.1.4.1.2272.1.12.10.46
Update errors received: Malformed AS Path
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpTxECodeHeader		1.3.6.1.4.1.2272.1.12.10.47
Total Header errors transmitted
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpTxECodeOpen		1.3.6.1.4.1.2272.1.12.10.48
Total Open errors transmitted
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpTxECodeUpdate		1.3.6.1.4.1.2272.1.12.10.49
Total Update errors transmitted
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpTxECodeHoldtimer		1.3.6.1.4.1.2272.1.12.10.50
Total Holdtimer errors transmitted
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpTxECodeFSM		1.3.6.1.4.1.2272.1.12.10.51
Total FSM errors transmitted
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpTxECodeCease		1.3.6.1.4.1.2272.1.12.10.52
Total Cease errors transmitted
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpTxHdrCodeNoSync		1.3.6.1.4.1.2272.1.12.10.53
Header Not Synchronized errors transmitted
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpTxHdrCodeInvalidMsgLen		1.3.6.1.4.1.2272.1.12.10.54
Header Invalid msg len errors transmitted
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpTxHdrCodeInvalidMsgType		1.3.6.1.4.1.2272.1.12.10.55
Header Invalid msg type errors transmitted
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpTxOpCodeBadVer		1.3.6.1.4.1.2272.1.12.10.56
Open errors transmitted: Bad Version
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpTxOpCodeBadAs		1.3.6.1.4.1.2272.1.12.10.57
Open errors transmitted: Bad AS Number
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpTxOpCodeBadRtID		1.3.6.1.4.1.2272.1.12.10.58
Open errors transmitted: Bad BGP Rtr ID
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpTxOpCodeUnsuppOption		1.3.6.1.4.1.2272.1.12.10.59
Open errors transmitted: Unsupported Option
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpTxOpCodeAuthFail		1.3.6.1.4.1.2272.1.12.10.60
Open errors transmitted: Auth Failures
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpTxOpCodeBadHold		1.3.6.1.4.1.2272.1.12.10.61
Open errors transmitted: Bad Hold Value
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpTxUpdCodeMalformedAttrList		1.3.6.1.4.1.2272.1.12.10.62
Update errors transmitted:Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpTxUpdCodeWelknownAttrUnrecog		1.3.6.1.4.1.2272.1.12.10.63
Update errors transmitted: Welknown Attr Unrecog
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpTxUpdCodeWelknownAttrMiss		1.3.6.1.4.1.2272.1.12.10.64
Update errors transmitted: Welknown Attr Missing
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpTxUpdCodeAttrFlagError		1.3.6.1.4.1.2272.1.12.10.65
Update errors transmitted: Attr Flag Error
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpTxUpdCodeAttrLenError		1.3.6.1.4.1.2272.1.12.10.66
Update errors transmitted: Attr Len Error
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpTxUpdCodeBadORIGINAttr		1.3.6.1.4.1.2272.1.12.10.67
Update errors transmitted: Bad ORIGIN Attr
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpTxUpdCodeASRoutingLoop		1.3.6.1.4.1.2272.1.12.10.68
Update errors transmitted: AS Routing Loop
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpTxUpdCodeBadNHAttr		1.3.6.1.4.1.2272.1.12.10.69
Update errors transmitted: Bad NEXT-HOP Attr
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpTxUpdCodeOptionalAttrError		1.3.6.1.4.1.2272.1.12.10.70
Update errors transmitted: Optional Attr Error
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpTxUpdCodeBadNetworkField		1.3.6.1.4.1.2272.1.12.10.71
Update errors transmitted: Bad Network Field
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpTxUpdCodeMalformedASPath		1.3.6.1.4.1.2272.1.12.10.72
Update errors transmitted: Malformed AS Path
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpReset		1.3.6.1.4.1.2272.1.12.10.73
reset Bgp global stats
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcStatBgpPeerTable		1.3.6.1.4.1.2272.1.12.11
A table used to store Bgp Peer statistics.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcStatBgpPeerEntry

rcStatBgpPeerEntry		1.3.6.1.4.1.2272.1.12.11.1
Bgp Peer statistics
Status: current	Access: not-accessible
OBJECT-TYPE
	RcStatBgpPeerEntry

rcStatBgpPeerAddr		1.3.6.1.4.1.2272.1.12.11.1.1
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcStatBgpPeerStarts		1.3.6.1.4.1.2272.1.12.11.1.2
Number of times peer BGP connection started
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerStops		1.3.6.1.4.1.2272.1.12.11.1.3
Number of times peer BGP connection stopped
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerOpens		1.3.6.1.4.1.2272.1.12.11.1.4
Number of times peer opens TCP
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerCloses		1.3.6.1.4.1.2272.1.12.11.1.5
Number of times peer closes TCP
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerFails		1.3.6.1.4.1.2272.1.12.11.1.6
Number of times peer TCP attempts failed
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerFatals		1.3.6.1.4.1.2272.1.12.11.1.7
Number of times peer TCP crashes due to fatal error
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerConnExps		1.3.6.1.4.1.2272.1.12.11.1.8
Number of times peer TCP retry timer expired
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerHoldExps		1.3.6.1.4.1.2272.1.12.11.1.9
Number of times peer hold timer expired
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerKeepExps		1.3.6.1.4.1.2272.1.12.11.1.10
Number of times peer keepalive timer expired
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerTxMsgs		1.3.6.1.4.1.2272.1.12.11.1.11
Total messages send by the peer
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerTxOpens		1.3.6.1.4.1.2272.1.12.11.1.12
Opens sent by the peer
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerTxKeeps		1.3.6.1.4.1.2272.1.12.11.1.13
Keepalives sent by the peer
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerTxUpdates		1.3.6.1.4.1.2272.1.12.11.1.14
Updates sent by the peer
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerTxNotifys		1.3.6.1.4.1.2272.1.12.11.1.15
Notifications sent by the peer
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerRxMsgs		1.3.6.1.4.1.2272.1.12.11.1.16
Total messages received by the peer
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerRxInCompPkts		1.3.6.1.4.1.2272.1.12.11.1.17
Incomplete message received by the peer
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerRxOpens		1.3.6.1.4.1.2272.1.12.11.1.18
Opens received by the peer
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerRxKeeps		1.3.6.1.4.1.2272.1.12.11.1.19
Keepalives received by the peer
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerRxUpdates		1.3.6.1.4.1.2272.1.12.11.1.20
Updates received by the peer
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerRxNotifys		1.3.6.1.4.1.2272.1.12.11.1.21
Notifications received by the peer
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerBadEvents		1.3.6.1.4.1.2272.1.12.11.1.22
Number of invalid events received by the peer
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerSyncFails		1.3.6.1.4.1.2272.1.12.11.1.23
Number of times FDB sync failed of the peer
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerRcvdTooShort		1.3.6.1.4.1.2272.1.12.11.1.24
Number of messages recieved by the peer that is too sho rt
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerNoMarker		1.3.6.1.4.1.2272.1.12.11.1.25
Number of messages without marker recieved by the peer
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerDropped		1.3.6.1.4.1.2272.1.12.11.1.26
Number of messages the peer has dropped
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerBadMsgTypes		1.3.6.1.4.1.2272.1.12.11.1.27
Number of messages with invalid message type
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerTrEvent		1.3.6.1.4.1.2272.1.12.11.1.28
Peer trace event
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerTxRoutes		1.3.6.1.4.1.2272.1.12.11.1.29
Number of NLRI sent by peer
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerRxRoutesAdded		1.3.6.1.4.1.2272.1.12.11.1.30
Number of routes added into loc_rib by this peer
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerRxRoutesReplaced		1.3.6.1.4.1.2272.1.12.11.1.31
Number of routes replaced by the routes received by the peer
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerRxNlri		1.3.6.1.4.1.2272.1.12.11.1.32
Number of NLRI received by the peer
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerRxValidUpdates		1.3.6.1.4.1.2272.1.12.11.1.33
Number of valid UPDATEs received by the peer
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerRxECodeHeader		1.3.6.1.4.1.2272.1.12.11.1.34
Total errors peer received: Header
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerRxECodeOpen		1.3.6.1.4.1.2272.1.12.11.1.35
Total errors peer received: Open
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerRxECodeUpdate		1.3.6.1.4.1.2272.1.12.11.1.36
Total errors peer received: Update
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerRxECodeHoldtimer		1.3.6.1.4.1.2272.1.12.11.1.37
Total errors peer received: Hold
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerRxECodeFSM		1.3.6.1.4.1.2272.1.12.11.1.38
Total errors peer received: Fsm
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerRxECodeCease		1.3.6.1.4.1.2272.1.12.11.1.39
Total errors peer received: Cease
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerRxHdrCodeNoSync		1.3.6.1.4.1.2272.1.12.11.1.40
Header errors peer received: Not Synchronized
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerRxHdrCodeInvalidMsgLen		1.3.6.1.4.1.2272.1.12.11.1.41
Header errors peer received: Invalid message length
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerRxHdrCodeInvalidMsgType		1.3.6.1.4.1.2272.1.12.11.1.42
Header errors peer received: Invalid message type
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerRxOpCodeBadVer		1.3.6.1.4.1.2272.1.12.11.1.43
Open errors peer received: Bad Version
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerRxOpCodeBadAs		1.3.6.1.4.1.2272.1.12.11.1.44
Open errors peer received: Bad AS number
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerRxOpCodeBadRtID		1.3.6.1.4.1.2272.1.12.11.1.45
Open errors peer received: Bad BGP ID
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerRxOpCodeUnsuppOption		1.3.6.1.4.1.2272.1.12.11.1.46
Open errors peer received: Unsupported Options
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerRxOpCodeAuthFail		1.3.6.1.4.1.2272.1.12.11.1.47
Open errors peer received: Authorization failures
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerRxOpCodeBadHold		1.3.6.1.4.1.2272.1.12.11.1.48
Open errors peer received: Bad Hold value
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerRxUpdCodeMalformedAttrList		1.3.6.1.4.1.2272.1.12.11.1.49
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerRxUpdCodeWelknownAttrUnrecog		1.3.6.1.4.1.2272.1.12.11.1.50
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerRxUpdCodeWelknownAttrMiss		1.3.6.1.4.1.2272.1.12.11.1.51
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerRxUpdCodeAttrFlagError		1.3.6.1.4.1.2272.1.12.11.1.52
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerRxUpdCodeAttrLenError		1.3.6.1.4.1.2272.1.12.11.1.53
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerRxUpdCodeBadORIGINAttr		1.3.6.1.4.1.2272.1.12.11.1.54
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerRxUpdCodeASRoutingLoop		1.3.6.1.4.1.2272.1.12.11.1.55
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerRxUpdCodeBadNHAttr		1.3.6.1.4.1.2272.1.12.11.1.56
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerRxUpdCodeOptionalAttrError		1.3.6.1.4.1.2272.1.12.11.1.57
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerRxUpdCodeBadNetworkField		1.3.6.1.4.1.2272.1.12.11.1.58
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerRxUpdCodeMalformedASPath		1.3.6.1.4.1.2272.1.12.11.1.59
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerTxECodeHeader		1.3.6.1.4.1.2272.1.12.11.1.60
Total errors peer received: Header
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerTxECodeOpen		1.3.6.1.4.1.2272.1.12.11.1.61
Total errors peer received: Open
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerTxECodeUpdate		1.3.6.1.4.1.2272.1.12.11.1.62
Total errors peer received: Update
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerTxECodeHoldtimer		1.3.6.1.4.1.2272.1.12.11.1.63
Total errors peer received: Hold
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerTxECodeFSM		1.3.6.1.4.1.2272.1.12.11.1.64
Total errors peer received: Fsm
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerTxECodeCease		1.3.6.1.4.1.2272.1.12.11.1.65
Total errors peer received: Cease
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerTxHdrCodeNoSync		1.3.6.1.4.1.2272.1.12.11.1.66
Header errors peer received: Not Synchronized
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerTxHdrCodeInvalidMsgLen		1.3.6.1.4.1.2272.1.12.11.1.67
Header errors peer received: Invalid message length
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerTxHdrCodeInvalidMsgType		1.3.6.1.4.1.2272.1.12.11.1.68
Header errors peer received: Invalid message type
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerTxOpCodeBadVer		1.3.6.1.4.1.2272.1.12.11.1.69
Open errors peer received: Bad Version
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerTxOpCodeBadAs		1.3.6.1.4.1.2272.1.12.11.1.70
Open errors peer received: Bad AS number
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerTxOpCodeBadRtID		1.3.6.1.4.1.2272.1.12.11.1.71
Open errors peer received: Bad BGP ID
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerTxOpCodeUnsuppOption		1.3.6.1.4.1.2272.1.12.11.1.72
Open errors peer received: Unsupported Options
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerTxOpCodeAuthFail		1.3.6.1.4.1.2272.1.12.11.1.73
Open errors peer received: Authorization failures
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerTxOpCodeBadHold		1.3.6.1.4.1.2272.1.12.11.1.74
Open errors peer received: Bad Hold value
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerTxUpdCodeMalformedAttrList		1.3.6.1.4.1.2272.1.12.11.1.75
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerTxUpdCodeWelknownAttrUnrecog		1.3.6.1.4.1.2272.1.12.11.1.76
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerTxUpdCodeWelknownAttrMiss		1.3.6.1.4.1.2272.1.12.11.1.77
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerTxUpdCodeAttrFlagError		1.3.6.1.4.1.2272.1.12.11.1.78
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerTxUpdCodeAttrLenError		1.3.6.1.4.1.2272.1.12.11.1.79
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerTxUpdCodeBadORIGINAttr		1.3.6.1.4.1.2272.1.12.11.1.80
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerTxUpdCodeASRoutingLoop		1.3.6.1.4.1.2272.1.12.11.1.81
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerTxUpdCodeBadNHAttr		1.3.6.1.4.1.2272.1.12.11.1.82
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerTxUpdCodeOptionalAttrError		1.3.6.1.4.1.2272.1.12.11.1.83
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerTxUpdCodeBadNetworkField		1.3.6.1.4.1.2272.1.12.11.1.84
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerTxUpdCodeMalformedASPath		1.3.6.1.4.1.2272.1.12.11.1.85
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerReset		1.3.6.1.4.1.2272.1.12.11.1.86
reset peer stats
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcStatBgpPeerAfTable		1.3.6.1.4.1.2272.1.12.13
A table used to store v4/v6 Bgp Peer statistics.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcStatBgpPeerAfEntry

rcStatBgpPeerAfEntry		1.3.6.1.4.1.2272.1.12.13.1
AF independent Bgp Peer statistics
Status: current	Access: not-accessible
OBJECT-TYPE
	RcStatBgpPeerAfEntry

rcStatBgpPeerAfAddrType		1.3.6.1.4.1.2272.1.12.13.1.1
Inet address type of the AF independent peer
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddressType

rcStatBgpPeerAfAddr		1.3.6.1.4.1.2272.1.12.13.1.2
Inet address of the AF independent peer
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddress

rcStatBgpPeerAfStarts		1.3.6.1.4.1.2272.1.12.13.1.3
Number of times peer BGP connection started
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfStops		1.3.6.1.4.1.2272.1.12.13.1.4
Number of times peer BGP connection stopped
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfOpens		1.3.6.1.4.1.2272.1.12.13.1.5
Number of times peer opens TCP
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfCloses		1.3.6.1.4.1.2272.1.12.13.1.6
Number of times peer closes TCP
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfFails		1.3.6.1.4.1.2272.1.12.13.1.7
Number of times peer TCP attempts failed
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfFatals		1.3.6.1.4.1.2272.1.12.13.1.8
Number of times peer TCP crashes due to fatal error
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfConnExps		1.3.6.1.4.1.2272.1.12.13.1.9
Number of times peer TCP retry timer expired
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfHoldExps		1.3.6.1.4.1.2272.1.12.13.1.10
Number of times peer hold timer expired
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfKeepExps		1.3.6.1.4.1.2272.1.12.13.1.11
Number of times peer keepalive timer expired
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfTxMsgs		1.3.6.1.4.1.2272.1.12.13.1.12
Total messages send by the peer
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfTxOpens		1.3.6.1.4.1.2272.1.12.13.1.13
Opens sent by the peer
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfTxKeeps		1.3.6.1.4.1.2272.1.12.13.1.14
Keepalives sent by the peer
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfTxUpdates		1.3.6.1.4.1.2272.1.12.13.1.15
Updates sent by the peer
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfTxNotifys		1.3.6.1.4.1.2272.1.12.13.1.16
Notifications sent by the peer
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfRxMsgs		1.3.6.1.4.1.2272.1.12.13.1.17
Total messages received by the peer
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfRxInCompPkts		1.3.6.1.4.1.2272.1.12.13.1.18
Incomplete message received by the peer
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfRxOpens		1.3.6.1.4.1.2272.1.12.13.1.19
Opens received by the peer
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfRxKeeps		1.3.6.1.4.1.2272.1.12.13.1.20
Keepalives received by the peer
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfRxUpdates		1.3.6.1.4.1.2272.1.12.13.1.21
Updates received by the peer
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfRxNotifys		1.3.6.1.4.1.2272.1.12.13.1.22
Notifications received by the peer
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfBadEvents		1.3.6.1.4.1.2272.1.12.13.1.23
Number of invalid events received by the peer
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfSyncFails		1.3.6.1.4.1.2272.1.12.13.1.24
Number of times FDB sync failed of the peer
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfRcvdTooShort		1.3.6.1.4.1.2272.1.12.13.1.25
Number of messages recieved by the peer that is too sho rt
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfNoMarker		1.3.6.1.4.1.2272.1.12.13.1.26
Number of messages without marker recieved by the peer
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfDropped		1.3.6.1.4.1.2272.1.12.13.1.27
Number of messages the peer has dropped
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfBadMsgTypes		1.3.6.1.4.1.2272.1.12.13.1.28
Number of messages with invalid message type
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfTrEvent		1.3.6.1.4.1.2272.1.12.13.1.29
Peer trace event
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfTxRoutes		1.3.6.1.4.1.2272.1.12.13.1.30
Number of NLRI sent by peer
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfRxRoutesAdded		1.3.6.1.4.1.2272.1.12.13.1.31
Number of routes added into loc_rib by this peer
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfRxRoutesReplaced		1.3.6.1.4.1.2272.1.12.13.1.32
Number of routes replaced by the routes received by the peer
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfRxNlri		1.3.6.1.4.1.2272.1.12.13.1.33
Number of NLRI received by the peer
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfRxValidUpdates		1.3.6.1.4.1.2272.1.12.13.1.34
Number of valid UPDATEs received by the peer
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfRxECodeHeader		1.3.6.1.4.1.2272.1.12.13.1.35
Total errors peer received: Header
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfRxECodeOpen		1.3.6.1.4.1.2272.1.12.13.1.36
Total errors peer received: Open
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfRxECodeUpdate		1.3.6.1.4.1.2272.1.12.13.1.37
Total errors peer received: Update
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfRxECodeHoldtimer		1.3.6.1.4.1.2272.1.12.13.1.38
Total errors peer received: Hold
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfRxECodeFSM		1.3.6.1.4.1.2272.1.12.13.1.39
Total errors peer received: Fsm
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfRxECodeCease		1.3.6.1.4.1.2272.1.12.13.1.40
Total errors peer received: Cease
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfRxHdrCodeNoSync		1.3.6.1.4.1.2272.1.12.13.1.41
Header errors peer received: Not Synchronized
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfRxHdrCodeInvalidMsgLen		1.3.6.1.4.1.2272.1.12.13.1.42
Header errors peer received: Invalid message length
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfRxHdrCodeInvalidMsgType		1.3.6.1.4.1.2272.1.12.13.1.43
Header errors peer received: Invalid message type
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfRxOpCodeBadVer		1.3.6.1.4.1.2272.1.12.13.1.44
Open errors peer received: Bad Version
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfRxOpCodeBadAs		1.3.6.1.4.1.2272.1.12.13.1.45
Open errors peer received: Bad AS number
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfRxOpCodeBadRtID		1.3.6.1.4.1.2272.1.12.13.1.46
Open errors peer received: Bad BGP ID
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfRxOpCodeUnsuppOption		1.3.6.1.4.1.2272.1.12.13.1.47
Open errors peer received: Unsupported Options
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfRxOpCodeAuthFail		1.3.6.1.4.1.2272.1.12.13.1.48
Open errors peer received: Authorization failures
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfRxOpCodeBadHold		1.3.6.1.4.1.2272.1.12.13.1.49
Open errors peer received: Bad Hold value
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfRxUpdCodeMalformedAttrList		1.3.6.1.4.1.2272.1.12.13.1.50
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfRxUpdCodeWelknownAttrUnrecog		1.3.6.1.4.1.2272.1.12.13.1.51
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfRxUpdCodeWelknownAttrMiss		1.3.6.1.4.1.2272.1.12.13.1.52
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfRxUpdCodeAttrFlagError		1.3.6.1.4.1.2272.1.12.13.1.53
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfRxUpdCodeAttrLenError		1.3.6.1.4.1.2272.1.12.13.1.54
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfRxUpdCodeBadORIGINAttr		1.3.6.1.4.1.2272.1.12.13.1.55
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfRxUpdCodeASRoutingLoop		1.3.6.1.4.1.2272.1.12.13.1.56
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfRxUpdCodeBadNHAttr		1.3.6.1.4.1.2272.1.12.13.1.57
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfRxUpdCodeOptionalAttrError		1.3.6.1.4.1.2272.1.12.13.1.58
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfRxUpdCodeBadNetworkField		1.3.6.1.4.1.2272.1.12.13.1.59
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfRxUpdCodeMalformedASPath		1.3.6.1.4.1.2272.1.12.13.1.60
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfTxECodeHeader		1.3.6.1.4.1.2272.1.12.13.1.61
Total errors peer received: Header
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfTxECodeOpen		1.3.6.1.4.1.2272.1.12.13.1.62
Total errors peer received: Open
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfTxECodeUpdate		1.3.6.1.4.1.2272.1.12.13.1.63
Total errors peer received: Update
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfTxECodeHoldtimer		1.3.6.1.4.1.2272.1.12.13.1.64
Total errors peer received: Hold
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfTxECodeFSM		1.3.6.1.4.1.2272.1.12.13.1.65
Total errors peer received: Fsm
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfTxECodeCease		1.3.6.1.4.1.2272.1.12.13.1.66
Total errors peer received: Cease
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfTxHdrCodeNoSync		1.3.6.1.4.1.2272.1.12.13.1.67
Header errors peer received: Not Synchronized
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfTxHdrCodeInvalidMsgLen		1.3.6.1.4.1.2272.1.12.13.1.68
Header errors peer received: Invalid message length
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfTxHdrCodeInvalidMsgType		1.3.6.1.4.1.2272.1.12.13.1.69
Header errors peer received: Invalid message type
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfTxOpCodeBadVer		1.3.6.1.4.1.2272.1.12.13.1.70
Open errors peer received: Bad Version
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfTxOpCodeBadAs		1.3.6.1.4.1.2272.1.12.13.1.71
Open errors peer received: Bad AS number
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfTxOpCodeBadRtID		1.3.6.1.4.1.2272.1.12.13.1.72
Open errors peer received: Bad BGP ID
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfTxOpCodeUnsuppOption		1.3.6.1.4.1.2272.1.12.13.1.73
Open errors peer received: Unsupported Options
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfTxOpCodeAuthFail		1.3.6.1.4.1.2272.1.12.13.1.74
Open errors peer received: Authorization failures
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfTxOpCodeBadHold		1.3.6.1.4.1.2272.1.12.13.1.75
Open errors peer received: Bad Hold value
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfTxUpdCodeMalformedAttrList		1.3.6.1.4.1.2272.1.12.13.1.76
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfTxUpdCodeWelknownAttrUnrecog		1.3.6.1.4.1.2272.1.12.13.1.77
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfTxUpdCodeWelknownAttrMiss		1.3.6.1.4.1.2272.1.12.13.1.78
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfTxUpdCodeAttrFlagError		1.3.6.1.4.1.2272.1.12.13.1.79
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfTxUpdCodeAttrLenError		1.3.6.1.4.1.2272.1.12.13.1.80
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfTxUpdCodeBadORIGINAttr		1.3.6.1.4.1.2272.1.12.13.1.81
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfTxUpdCodeASRoutingLoop		1.3.6.1.4.1.2272.1.12.13.1.82
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfTxUpdCodeBadNHAttr		1.3.6.1.4.1.2272.1.12.13.1.83
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfTxUpdCodeOptionalAttrError		1.3.6.1.4.1.2272.1.12.13.1.84
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfTxUpdCodeBadNetworkField		1.3.6.1.4.1.2272.1.12.13.1.85
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfTxUpdCodeMalformedASPath		1.3.6.1.4.1.2272.1.12.13.1.86
Update errors peer received: Malformed Attr List
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStatBgpPeerAfReset		1.3.6.1.4.1.2272.1.12.13.1.87
reset peer stats
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcStgMaxStgs		1.3.6.1.4.1.2272.1.13.1
The maximum number of spanning tree groups this device can support concurrently.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcStgNumStgs		1.3.6.1.4.1.2272.1.13.2
The number of spanning tree groups that are currently defined.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcStgUnassignedPorts		1.3.6.1.4.1.2272.1.13.3
A bitfield used to identify which ports in the system currently not assigned to any STG. The bitfield is 32 octets long representing ports 0 to 255 (inclusive).
Status: current	Access: read-only
OBJECT-TYPE
	PortSet

rcStgTable		1.3.6.1.4.1.2272.1.13.4
A table used to store Spanning Tree Group (STG) information. Each row in the table specifies a different STG in the device.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcStgEntry

rcStgEntry		1.3.6.1.4.1.2272.1.13.4.1
STG attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	RcStgEntry

rcStgId		1.3.6.1.4.1.2272.1.13.4.1.1
An identifier used to identify a STG in the device.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..64

rcStgTaggedBpduAddress		1.3.6.1.4.1.2272.1.13.4.1.2
The MAC address to be assigned to the destination mac address field in tagged BPDUs. The default address is the well known multicast group address 01-80-c2-00-00-00.
Status: current	Access: read-write
OBJECT-TYPE
	MacAddress

rcStgTaggedBpduVlanId		1.3.6.1.4.1.2272.1.13.4.1.3
The VLAN ID to be used for tagging BPDUs.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcStgBridgeAddress		1.3.6.1.4.1.2272.1.13.4.1.4
The MAC address used by this bridge when it must be referred to in a unique fashion. It is recommended that this be the numerically smallest MAC address of all ports that belong to this bridge. However it is only required to be unique. When concatenated with rcStgPriority a unique BridgeIdentifier is formed which is used in the Spanning Tree Protocol.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rcStgNumPorts		1.3.6.1.4.1.2272.1.13.4.1.5
The number of ports controlled by this bridging entity.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcStgProtocolSpecification		1.3.6.1.4.1.2272.1.13.4.1.6
An indication of what version of the Spanning Tree Protocol is being run. The value 'decLb100(2)' indicates the DEC LANbridge 100 Spanning Tree protocol. IEEE 802.1d implementations will return 'ieee8021d(3)'. If future versions of the IEEE Spanning Tree Protocol are released that are incompatible with the current version a new value will be defined.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), decLb100(2), ieee8021d(3)

rcStgPriority		1.3.6.1.4.1.2272.1.13.4.1.7
The value of the write-able portion of the Bridge ID, i.e., the first two octets of the (8 octet long) Bridge ID. The other (last) 6 octets of the Bridge ID are given by the value of rcStgBridgeAddress.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

rcStgTimeSinceTopologyChange		1.3.6.1.4.1.2272.1.13.4.1.8
The time (in hundredths of a second) since the last time a topology change was detected by the bridge entity.
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

rcStgTopChanges		1.3.6.1.4.1.2272.1.13.4.1.9
The total number of topology changes detected by this bridge since the management entity was last reset or initialized.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStgDesignatedRoot		1.3.6.1.4.1.2272.1.13.4.1.10
The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
Status: current	Access: read-only
OBJECT-TYPE
	BridgeId

rcStgRootCost		1.3.6.1.4.1.2272.1.13.4.1.11
The cost of the path to the root as seen from this bridge.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcStgRootPort		1.3.6.1.4.1.2272.1.13.4.1.12
The port number of the port which offers the lowest cost path from this bridge to the root bridge.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcStgMaxAge		1.3.6.1.4.1.2272.1.13.4.1.13
The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.
Status: current	Access: read-only
OBJECT-TYPE
	Timeout

rcStgHelloTime		1.3.6.1.4.1.2272.1.13.4.1.14
The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using.
Status: current	Access: read-only
OBJECT-TYPE
	Timeout

rcStgHoldTime		1.3.6.1.4.1.2272.1.13.4.1.15
This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcStgForwardDelay		1.3.6.1.4.1.2272.1.13.4.1.16
This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. [Note that this value is the one that this bridge is currently using, in contrast to rcStgBridgeForwardDelay which is the value that this bridge and all others would start using if/when this bridge were to become the root.]
Status: current	Access: read-only
OBJECT-TYPE
	Timeout

rcStgBridgeMaxAge		1.3.6.1.4.1.2272.1.13.4.1.17
The value that all bridges use for MaxAge when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of rcStgBridgeHelloTime. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
Status: current	Access: read-write
OBJECT-TYPE
	Timeout	600..4000

rcStgBridgeHelloTime		1.3.6.1.4.1.2272.1.13.4.1.18
The value that all bridges use for HelloTime when this bridge is acting as the root. The granularity of this timer is specified by 802.1D- 1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
Status: current	Access: read-write
OBJECT-TYPE
	Timeout	100..1000

rcStgBridgeForwardDelay		1.3.6.1.4.1.2272.1.13.4.1.19
The value that all bridges use for ForwardDelay when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of rcStgBridgeMaxAge. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
Status: current	Access: read-write
OBJECT-TYPE
	Timeout	400..3000

rcStgEnableStp		1.3.6.1.4.1.2272.1.13.4.1.20
Indicate whether the spanning tree protocol should be active in this STG.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcStgStpTrapEnable		1.3.6.1.4.1.2272.1.13.4.1.21
Indicate whether traps relating to the spanning tree protocol should be sent for this STG.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcStgPortMembers		1.3.6.1.4.1.2272.1.13.4.1.22
A bitfield used to identify which ports in the system are members this STG. The bitfield is 32 octets long representing ports 0 to 255 (inclusive).
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..88)

rcStgRowStatus		1.3.6.1.4.1.2272.1.13.4.1.23
Row status.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcStgPortStpState		1.3.6.1.4.1.2272.1.13.4.1.24
Every 2 bitfields used to identify a port state in this STG. Port state is cataloged as non-stp(0), blocking(1), learning(2), and forwarding(3).
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(176)

rcStgType		1.3.6.1.4.1.2272.1.13.4.1.25
Type of Stg.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	normal(1), svlan(2), pbt(3), spbm(7)

rcStgNtStgEnable		1.3.6.1.4.1.2272.1.13.4.1.26
Indicates whether this STG is Operating in Nortel Mode or in Cisco Mode. true = Nortel Mode false = Cisco Mode.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcStgPortTable		1.3.6.1.4.1.2272.1.13.5
A table used to store Spanning Tree Group (STG) port related information. If a port is associated with more than one STGs, the port will have one entry in this table for each STG it assigned to.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcStgPortEntry

rcStgPortEntry		1.3.6.1.4.1.2272.1.13.5.1
STG Port attributes
Status: current	Access: not-accessible
OBJECT-TYPE
	RcStgPortEntry

rcStgPort		1.3.6.1.4.1.2272.1.13.5.1.1
The port number of the port for which this entry contains Spanning Tree Protocol management information.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcStgPortStgId		1.3.6.1.4.1.2272.1.13.5.1.2
The STG identifier this port is assigned to.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..128

rcStgPortPriority		1.3.6.1.4.1.2272.1.13.5.1.3
The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID. The other octet of the Port ID is given by the value of rcStgPort.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

rcStgPortState		1.3.6.1.4.1.2272.1.13.5.1.4
The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the broken(6) state. For ports which are disabled (see rcStgPortEnable), this object will have a value of disabled(1).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(1), blocking(2), listening(3), learning(4), forwarding(5), broken(6)

rcStgPortEnableStp		1.3.6.1.4.1.2272.1.13.5.1.5
The enabled/disabled status of the port.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcStgPortFastStart		1.3.6.1.4.1.2272.1.13.5.1.6
When this flag is set, the port is moved straight to the forwarding(5) state upon being enabled.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcStgPortPathCost		1.3.6.1.4.1.2272.1.13.5.1.7
The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1990 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

rcStgPortDesignatedRoot		1.3.6.1.4.1.2272.1.13.5.1.8
The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.
Status: current	Access: read-only
OBJECT-TYPE
	BridgeId

rcStgPortDesignatedCost		1.3.6.1.4.1.2272.1.13.5.1.9
The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcStgPortDesignatedBridge		1.3.6.1.4.1.2272.1.13.5.1.10
The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment.
Status: current	Access: read-only
OBJECT-TYPE
	BridgeId

rcStgPortDesignatedPort		1.3.6.1.4.1.2272.1.13.5.1.11
The Port Identifier of the port on the Designated Bridge for this port's segment.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(2)

rcStgPortForwardTransitions		1.3.6.1.4.1.2272.1.13.5.1.12
The number of times this port has transitioned from the Learning state to the Forwarding state.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStgPortInConfigBpdus		1.3.6.1.4.1.2272.1.13.5.1.13
The number of Config BPUDs received by this port.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStgPortInTcnBpdus		1.3.6.1.4.1.2272.1.13.5.1.14
The number of Topology Change Notification BPUDs received by this port.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStgPortInBadBpdus		1.3.6.1.4.1.2272.1.13.5.1.15
The number of Bad BPUDs received by this port.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStgPortOutConfigBpdus		1.3.6.1.4.1.2272.1.13.5.1.16
The number of Config BPUDs transmitted by this port.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStgPortOutTcnBpdus		1.3.6.1.4.1.2272.1.13.5.1.17
The number of Topology Change Notification BPUDs transmitted by this port.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcStgPortRowStatus		1.3.6.1.4.1.2272.1.13.5.1.18
Row status.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcStgPortChangeDetection		1.3.6.1.4.1.2272.1.13.5.1.19
If disabled, topology change notifications are not sent for the port.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcStgPortPathCost32		1.3.6.1.4.1.2272.1.13.5.1.20
The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1998 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN. Replacement for deprecated object dot1dStpPortPathCost.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..200000000

rcStgNotAllowedPorts		1.3.6.1.4.1.2272.1.13.6
A bitfield used to identify which ports in the system that cannot be assigned to any STG (i.e., which ports are single routable ports). The bitfield is 32 octets long representing ports 0 to 255 (inclusive).
Status: current	Access: read-only
OBJECT-TYPE
	PortSet

rcBridgeFdbTable		1.3.6.1.4.1.2272.1.14.1
This table is an replacement to the standard dot1dTpFdbTable in rfc1493.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcBridgeFdbEntry

rcBridgeFdbEntry		1.3.6.1.4.1.2272.1.14.1.1
Information about a specific unicast MAC address for which the bridge has some forwarding information.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	RcBridgeFdbEntry

rcBridgeFdbStatus		1.3.6.1.4.1.2272.1.14.1.1.1
This object indicates the status of this entry.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), invalid(2), learned(3), self(4), mgmt(5)

rcBridgeFdbAddress		1.3.6.1.4.1.2272.1.14.1.1.2
A unicast MAC address for which the bridge has forwarding and/or filtering information.
Status: deprecated	Access: read-only
OBJECT-TYPE
	MacAddress

rcBridgeFdbPort		1.3.6.1.4.1.2272.1.14.1.1.3
Either the value '0', or the port number of the port on which a frame having a source address equal to the value of the corresponding instance of rcBridgeFdbAddress has been seen. A value of '0' indicates that the port number has not been learned but that the bridge does have some forwarding/filtering information about this address (e.g. in the dot1dStaticTable). Implementors are encouraged to assign the port value to this object whenever it is learned even for addresses for which the corresponding value of rcBridgeFdbStatus is not learned(3).
Status: deprecated	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcBridgeFdbMonitor		1.3.6.1.4.1.2272.1.14.1.1.4
Used to indicate whether monitoring should be performed on this unicast MAC address. If monitoring is enabled, any packet received with a matching destination MAC address will be forwarded to the port configured to receive monitor traffic.
Status: deprecated	Access: read-write
OBJECT-TYPE
	TruthValue

rcBridgeFdbPriority		1.3.6.1.4.1.2272.1.14.1.1.5
Used to indicate the priority of the incoming frames with this destination Mac Address.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	low(0), high(1)

rcBridgeFdbQosLevel		1.3.6.1.4.1.2272.1.14.1.1.6
Used to indicate the qos level of the incoming frames with this destination Mac Address.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	level0(0), level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7)

rcBridgeFdbSmltRemote		1.3.6.1.4.1.2272.1.14.1.1.7
A MAC address indicate for remote learnt, either local or remote.
Status: deprecated	Access: read-only
OBJECT-TYPE
	TruthValue

rcBridgeFdbVlanId		1.3.6.1.4.1.2272.1.14.1.1.8
Tok_String
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	1..4094

rcBridgeFdbTblSize		1.3.6.1.4.1.2272.1.14.2
Used to indicate the number of entries in the bridge forwarding database table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcBridgeStaticTable		1.3.6.1.4.1.2272.1.14.3
This table is a proprietary replacement to the standard dot1dStaticTable in rfc1493.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcBridgeStaticEntry

rcBridgeStaticEntry		1.3.6.1.4.1.2272.1.14.3.1
A table containing forwarding information about unicast entries configured into the bridge by management. This information is used by the transparent bridging function in determining how to propagate a received frame.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcBridgeStaticEntry

rcBridgeStaticAddress		1.3.6.1.4.1.2272.1.14.3.1.1
The MAC address of this entry.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rcBridgeStaticPort		1.3.6.1.4.1.2272.1.14.3.1.2
Port on which the MAC address is found.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcBridgeStaticMonitor		1.3.6.1.4.1.2272.1.14.3.1.3
Used to indicate whether monitoring should be performed on incoming packets that match this entry.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcBridgeStaticPriority		1.3.6.1.4.1.2272.1.14.3.1.4
Used to indicate forwarding priority of incoming packets that match this entry.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	low(0), high(1)

rcBridgeStaticStatus		1.3.6.1.4.1.2272.1.14.3.1.5
This object indicates the status of this entry. The default value is permanent(3).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), invalid(2), permanent(3), deleteOnReset(4), deleteOnTimeout(5)

rcBridgeStaticQosLevel		1.3.6.1.4.1.2272.1.14.3.1.6
Used to indicate the qos level.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	level0(0), level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7)

rcBridgeStaticVlanId		1.3.6.1.4.1.2272.1.14.3.1.7
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4094

rcBridgeStaticTblSize		1.3.6.1.4.1.2272.1.14.4
Used to indicate the number of entries in the bridge static table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcBridgeFilterTable		1.3.6.1.4.1.2272.1.14.5
This table is a proprietary replacement to the standard dot1dStaticTable (Filtering information) in rfc1493.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcBridgeFilterEntry

rcBridgeFilterEntry		1.3.6.1.4.1.2272.1.14.5.1
A table containing filtering information configured into the bridge by management specifying a dest- ination address on a specific port and a set of incoming ports. Frames received from one of the incoming ports and containing the specific destination addresses are not allowed to be forwarded.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcBridgeFilterEntry

rcBridgeFilterAddress		1.3.6.1.4.1.2272.1.14.5.1.1
The MAC address of this entry. This address is used to match the destination address of incoming packets.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rcBridgeFilterPort		1.3.6.1.4.1.2272.1.14.5.1.2
Port on which this MAC address is found.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcBridgeFilterNotAllowedFrom		1.3.6.1.4.1.2272.1.14.5.1.3
Used to indicate a set of ports. Traffic arriving on any of the specified ports is not forwarded to this MAC address.
Status: obsolete	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(88)

rcBridgeFilterStatus		1.3.6.1.4.1.2272.1.14.5.1.4
This object indicates the status of this entry. The default value is permanent(3).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), invalid(2), permanent(3), deleteOnReset(4), deleteOnTimeout(5)

rcBridgeFilterVlanId		1.3.6.1.4.1.2272.1.14.5.1.5
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4094

rcBridgeFilterPcap		1.3.6.1.4.1.2272.1.14.5.1.6
To enable pcap for the fdb-filter
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcBridgeFilterDestDiscard		1.3.6.1.4.1.2272.1.14.5.1.7
Used to indicate a set of ports. Traffic arriving on any of the specified ports from this MAC address.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(88)

rcBridgeFilterSrcDiscard		1.3.6.1.4.1.2272.1.14.5.1.8
Used to indicate a set of ports. Traffic arriving on any of the specified ports is not forwarded to this MAC address.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(88)

rcBridgeFilterTblSize		1.3.6.1.4.1.2272.1.14.6
Used to indicate the number of entries in the bridge filter table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcBridgeUnknownMacDiscardTable		1.3.6.1.4.1.2272.1.14.7
This table is used to configure the 'unknown mac discard' feature. This feature applies to layer 2 and layer 3 packets coming from or going out to a specific physical port.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcBridgeUnknownMacDiscardEntry

rcBridgeUnknownMacDiscardEntry		1.3.6.1.4.1.2272.1.14.7.1
A table containing information configuring the 'unknown mac discard' feature.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcBridgeUnknownMacDiscardEntry

rcBridgeUnknownMacDiscardIfIndex		1.3.6.1.4.1.2272.1.14.7.1.1
Port on which this 'unknown mac discard' configuration applied to.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcBridgeUnknownMacDiscardAutoLearnEnable		1.3.6.1.4.1.2272.1.14.7.1.2
This variable is used to enable/disable the auto-learn capability of a specific port. The default value is auto-learn disabled.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcBridgeUnknownMacDiscardAutoLearnMode		1.3.6.1.4.1.2272.1.14.7.1.3
This variable is used to control the auto-learn mode to either one-shot or continuous. In one-shot mode, the first n MAC addresses will be learned. The number n is dependents on the system's available resource. In continuous mode, MAC address is continuous learned until the resource limit is reached. After that the subsequent MAC will be disallowed until one of the original learned MAC is aged out. The default value is one-shot mode.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	oneShot(1), continuous(2)

rcBridgeUnknownMacDiscardAutoLearnTableMode		1.3.6.1.4.1.2272.1.14.7.1.4
This MIB variable is used to lock or unlock the auto-learn MAC table. When the auto-learn table is lock neither new MAC will be learned nor the original learned MAC will be aged out. User needs to lock the auto-learn table before MAC addresses can be save to the NVRAM. The whole auto-learn table will be flushed when the setting change from lock to unlock mode. The default value is unlock mode.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unlock(1), lock(2)

rcBridgeUnknownMacDiscardLogViolations		1.3.6.1.4.1.2272.1.14.7.1.5
This variable controls the logging action that the system will take when a MAC address violation event was detected. The value 'enable' means a log record will be written to the system log file when a violation event was detected. The default value is enable.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

rcBridgeUnknownMacDiscardSendTrap		1.3.6.1.4.1.2272.1.14.7.1.6
This variable controls the send trap action that system will take when a MAC address violation event was detected. The value 'enable' means a SNMP trap packet will be send to the management station when a violation event was detected. The default value is disable.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

rcBridgeUnknownMacDiscardDisablePort		1.3.6.1.4.1.2272.1.14.7.1.7
This variable controls the 'disable-port' action that system will take when a MAC address violation event was detected. The value 'enable' means the specific port will be disabled when the violation event was detected. It needs user manually to bring the port back once it was disabled. The default value is disable.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

rcBridgeUnknownMacDiscardDefaultAutoLearnMonitor		1.3.6.1.4.1.2272.1.14.7.1.8
This variable controls the default monitor setting of an auto-learn MAC address. The value 'monitor' means a copy of packet that send from or to the auto-learned MAC address will be forwarded to the designated monitoring port on the system. The default value is none.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), monitor(2)

rcBridgeUnknownMacDiscardDefaultAutoLearnPriority		1.3.6.1.4.1.2272.1.14.7.1.9
This variable controls the default priority setting of an auto-learn MAC address. The value 'low' means packets send from the MAC address is forwarded at low priority. The value 'high' means packets send from the MAC address is forwarded at high priority. The default value is low.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	low(1), high(2)

rcBridgeUnknownMacDiscardMacCountMax		1.3.6.1.4.1.2272.1.14.7.1.10
This variable represents the maxium number of MACc that can be added to some port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..2048

rcBridgeUnknownMacDiscardMacCountCur		1.3.6.1.4.1.2272.1.14.7.1.11
This variable represents the current number of MACs that have been added to some port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..2048

rcBridgeManualEditTable		1.3.6.1.4.1.2272.1.14.8
This table is used to specify what MAC addresses can be learned on each port.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcBridgeManualEditEntry

rcBridgeManualEditEntry		1.3.6.1.4.1.2272.1.14.8.1
A table containing information of MAC addresses that can be learned.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcBridgeManualEditEntry

rcBridgeManualEditAddress		1.3.6.1.4.1.2272.1.14.8.1.1
This variable contains the source MAC address of an entry.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rcBridgeManualEditPorts		1.3.6.1.4.1.2272.1.14.8.1.2
This variable contains the allowed ports on which the MAC address of this entry can be learned.
Status: current	Access: read-write
OBJECT-TYPE
	PortSet

rcBridgeManualEditMonitor		1.3.6.1.4.1.2272.1.14.8.1.3
This variable specifies the monitoring setting of the MAC address. The value 'true' means a copy of packet frame that send from or to the MAC address is forwarded to the designated monitoring port on the system. The default value is false.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcBridgeManualEditPriority		1.3.6.1.4.1.2272.1.14.8.1.4
This variable specifies the priority setting of the MAC address. The value 'low' means packet frames send from the MAC address is forwarded at low priority. The default value is low.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	low(1), high(2)

rcBridgeManualEditStatus		1.3.6.1.4.1.2272.1.14.8.1.5
The variable controls the status of a MAC address in the table. The value 'active' is used to add the MAC address entry into the table. The value 'invalid' is used to delete the MAC address from the table.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), invalid(2), active(3)

rcBridgeManualEditTblSize		1.3.6.1.4.1.2272.1.14.9
Used to indicate the number of entries in the manual edit table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcBridgeAutoLearnTable		1.3.6.1.4.1.2272.1.14.10
This table contains information of auto-learned MAC address when the 'unknow MAC discard' table's auto-learn is enabled. User must explicitly lock and save the table into NVRAM in order to have this table has the same configuration cross the system reset.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcBridgeAutoLearnEntry

rcBridgeAutoLearnEntry		1.3.6.1.4.1.2272.1.14.10.1
Entries in this table are created automatically when the user explicitly does a lock operation on the auto-learn-table (i.e., when 'AutoLearnTableMode' is set to lock(2)).
Status: current	Access: not-accessible
OBJECT-TYPE
	RcBridgeAutoLearnEntry

rcBridgeAutoLearnAddress		1.3.6.1.4.1.2272.1.14.10.1.1
This variable contains the source MAC address of the entries.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rcBridgeAutoLearnPort		1.3.6.1.4.1.2272.1.14.10.1.2
This variable contains the port where the MAC address was learned.
Status: current	Access: read-only
OBJECT-TYPE
	PortSet

rcBridgeAutoLearnMonitor		1.3.6.1.4.1.2272.1.14.10.1.3
This variable contains the monitor setting of the MAC address. The value 'true' means a copy of packet frame that send from or to the MAC address is forwarded to the designated monitoring port on the system. This value should be synchronized with the setting of 'unknow MAC discard' table's 'Default AutoLearnMonitor' setting when the MAC address was learned.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcBridgeAutoLearnPriority		1.3.6.1.4.1.2272.1.14.10.1.4
This variable contains the priority setting of the MAC address. The value 'low' means packet frames send from the MAC address is forwarded at low priority. The value 'high' means packet frames send from the MAC address is forwarded at high priority. This value should be synchronized with the setting of 'unknow MAC discard' table's 'DefaultAutoLearnPriority' setting when the MAC address was learned.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	low(1), high(2)

rcBridgeAutoLearnAction		1.3.6.1.4.1.2272.1.14.10.1.5
This variable is for converting an auto-learned MAC address entry to a manual edit MAC address entry. This variable provides a mechanism for user to move a MAC address entry from auto-learn table to manual edit table.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), convertToManualEdit(1)

rcBridgeAutoLearnTblSize		1.3.6.1.4.1.2272.1.14.11
Used to indicate the number of entries in the auto learn table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcBridgeStaticMulticastTable		1.3.6.1.4.1.2272.1.14.12
Tok_String
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcBridgeStaticMulticastEntry

rcBridgeStaticMulticastEntry		1.3.6.1.4.1.2272.1.14.12.1
Tok_String
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	RcBridgeStaticMulticastEntry

rcBridgeStaticMulticastAddress		1.3.6.1.4.1.2272.1.14.12.1.1
src mac addr.
Status: deprecated	Access: read-only
OBJECT-TYPE
	MacAddress

rcBridgeStaticMulticastForwardingPorts		1.3.6.1.4.1.2272.1.14.12.1.2
ports for forward this mac
Status: deprecated	Access: read-write
OBJECT-TYPE
	PortSet

rcBridgeStaticMulticastMltIds		1.3.6.1.4.1.2272.1.14.12.1.3
list of mlts this mac will be forwarded on
Status: deprecated	Access: read-write
OBJECT-TYPE
	IdList

rcBridgeStaticMulticastRowStatus		1.3.6.1.4.1.2272.1.14.12.1.4
row status
Status: deprecated	Access: read-write
OBJECT-TYPE
	RowStatus

rcBridgeStaticMulticastVlanId		1.3.6.1.4.1.2272.1.14.12.1.5
Vlan Id
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	1..4095

rcBridgeStaticMulticastNumMltIds		1.3.6.1.4.1.2272.1.14.12.1.6
number of mlts Ids
Status: deprecated	Access: read-only
OBJECT-TYPE
	Integer32

rcBridgeStaticMulticastTblSize		1.3.6.1.4.1.2272.1.14.13
Used to indicate the number of entries in the static multicast table.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Integer32

rcRateLimitTable		1.3.6.1.4.1.2272.1.14.14
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcRateLimitEntry

rcRateLimitEntry		1.3.6.1.4.1.2272.1.14.14.1
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	RcRateLimitEntry

rcRateLimitIfIndex		1.3.6.1.4.1.2272.1.14.14.1.1
Port ifindex.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcRateLimitIfTrafficType		1.3.6.1.4.1.2272.1.14.14.1.2
Type of traffic allowed.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	multicast(1), broadcast(2)

rcRateLimitIfAllowedRate		1.3.6.1.4.1.2272.1.14.14.1.3
Allowed traffic rate. If chassis type is 8100.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..25

rcRateLimitIfEnable		1.3.6.1.4.1.2272.1.14.14.1.4
Turn on/off rate limiting on this interface.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcRateLimitIfAllowedRatePps		1.3.6.1.4.1.2272.1.14.14.1.5
Allowed traffic rate packets per second. If chassis type is 8600/8800.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcRateLimitIfAllowedRateKbps		1.3.6.1.4.1.2272.1.14.14.1.6
Allowed traffic rate Kbits per second. If chassis type is R-module.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	250..2147483647

rcBridgeStaticMcastTable		1.3.6.1.4.1.2272.1.14.15
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcBridgeStaticMcastEntry

rcBridgeStaticMcastEntry		1.3.6.1.4.1.2272.1.14.15.1
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	RcBridgeStaticMcastEntry

rcBridgeStaticMcastVlanId		1.3.6.1.4.1.2272.1.14.15.1.1
Vlan Id
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4095

rcBridgeStaticMcastAddress		1.3.6.1.4.1.2272.1.14.15.1.2
src mac addr.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rcBridgeStaticMcastForwardingPorts		1.3.6.1.4.1.2272.1.14.15.1.3
ports for forward this mac
Status: current	Access: read-write
OBJECT-TYPE
	PortSet

rcBridgeStaticMcastMltIds		1.3.6.1.4.1.2272.1.14.15.1.4
list of mlts this mac will be forwarded on
Status: current	Access: read-write
OBJECT-TYPE
	IdList

rcBridgeStaticMcastNumMltIds		1.3.6.1.4.1.2272.1.14.15.1.5
number of mlts Ids
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcBridgeStaticMcastRowStatus		1.3.6.1.4.1.2272.1.14.15.1.6
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcBridgeFdbProtectTable		1.3.6.1.4.1.2272.1.14.17
This table gives information about the mac learning limits on a particular port.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcBridgeFdbProtectEntry

rcBridgeFdbProtectEntry		1.3.6.1.4.1.2272.1.14.17.1
Information about a specific MAC address learning limits of a specific port.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcBridgeFdbProtectEntry

rcBridgeFdbProtectPortNum		1.3.6.1.4.1.2272.1.14.17.1.1
This object is the interface on which MAC address learning limit is applied.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcBridgeFdbProtectMaxMacCount		1.3.6.1.4.1.2272.1.14.17.1.2
Used to indicate maximum number of MAC address that can be learnt on the port.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..1000000

rcBridgeFdbProtectMinMacCount		1.3.6.1.4.1.2272.1.14.17.1.3
Used to indicate minimum number of MAC address learnt which mac address learning will be re-enabled on the port.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..1000000

rcBridgeFdbProtectEnable		1.3.6.1.4.1.2272.1.14.17.1.4
Used to enable or disable MAC learning limit feature on the port.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcBridgeFdbProtectCurrentMacCount		1.3.6.1.4.1.2272.1.14.17.1.5
This object indicates the current number of MAC address learnt on the port.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcBridgeFdbProtectMacLearning		1.3.6.1.4.1.2272.1.14.17.1.6
This object indicates whether the port can currrently learn new MAC addresses or not.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcBridgeFdbProtectViolationLogTrap		1.3.6.1.4.1.2272.1.14.17.1.7
Used to enable or disable logging and sending of snmp trap, once MAC learning limit is reached for the port.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcBridgeFdbProtectViolationDownPort		1.3.6.1.4.1.2272.1.14.17.1.8
Used to enable or disable the action of disabling the port, once MAC learning limit is reached for the port.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcBridgeNewFdbTable		1.3.6.1.4.1.2272.1.14.18
This table is an replacement to the standard dot1dTpFdbTable in rfc1493.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcBridgeNewFdbEntry

rcBridgeNewFdbEntry		1.3.6.1.4.1.2272.1.14.18.1
Information about a specific unicast MAC address for which the bridge has some forwarding information.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcBridgeNewFdbEntry

rcBridgeNewFdbStatus		1.3.6.1.4.1.2272.1.14.18.1.1
This object indicates the status of this entry.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), invalid(2), learned(3), self(4), mgmt(5)

rcBridgeNewFdbAddress		1.3.6.1.4.1.2272.1.14.18.1.2
A unicast MAC address for which the bridge has forwarding and/or filtering information.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rcBridgeNewFdbPort		1.3.6.1.4.1.2272.1.14.18.1.3
Either the value '0', or the port number of the port on which a frame having a source address equal to the value of the corresponding instance of rcBridgeNewFdbAddress has been seen. A value of '0' indicates that the port number has not been learned but that the bridge does have some forwarding/filtering information about this address (e.g. in the dot1dStaticTable). Implementors are encouraged to assign the port value to this object whenever it is learned even for addresses for which the corresponding value of rcBridgeNewFdbStatus is not learned(3).
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcBridgeNewFdbMonitor		1.3.6.1.4.1.2272.1.14.18.1.4
Used to indicate whether monitoring should be performed on this unicast MAC address. If monitoring is enabled, any packet received with a matching destination MAC address will be forwarded to the port configured to receive monitor traffic.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcBridgeNewFdbQosLevel		1.3.6.1.4.1.2272.1.14.18.1.5
Used to indicate the qos level of the incoming frames with this destination Mac Address.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	level0(0), level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7)

rcBridgeNewFdbSmltRemote		1.3.6.1.4.1.2272.1.14.18.1.6
A MAC address indicate for remote learnt, either local or remote.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcBridgeNewFdbVlanId		1.3.6.1.4.1.2272.1.14.18.1.7
Used to indicate the Vlan ID for this MAC address.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4094

rcBridgeRemoteMacTable		1.3.6.1.4.1.2272.1.14.21
This table is for PLSB cvlan UNI remote mac entries
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcBridgeRemoteMacEntry

rcBridgeRemoteMacEntry		1.3.6.1.4.1.2272.1.14.21.1
Information about a specific cvlan UNI remote MAC address for which the bridge has the forwarding information.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcBridgeRemoteMacEntry

rcBridgeRemoteMacVlanId		1.3.6.1.4.1.2272.1.14.21.1.1
Used to indicate the Vlan ID for this MAC address.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..4094

rcBridgeRemoteMacAddr		1.3.6.1.4.1.2272.1.14.21.1.2
A customer MAC address for which the bridge has forwarding and/or filtering information.
Status: current	Access: not-accessible
OBJECT-TYPE
	MacAddress

rcBridgeRemoteMacStatus		1.3.6.1.4.1.2272.1.14.21.1.3
This object indicates the status of this entry.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), invalid(2), learned(3), self(4), mgmt(5)

rcBridgeRemoteMacDestAddr		1.3.6.1.4.1.2272.1.14.21.1.4
A provider MAC address for which the bridge has forwarding and/or filtering information.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rcBridgeRemoteMacPrimaryBVlanId		1.3.6.1.4.1.2272.1.14.21.1.5
Used to indicate the BVlan ID for this MAC address.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..4094

rcBridgeRemoteMacPrimaryDestSysName		1.3.6.1.4.1.2272.1.14.21.1.6
Primary System name of the node where MAC address entry come from.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..255)

rcBridgeRemoteMacPrimaryPort		1.3.6.1.4.1.2272.1.14.21.1.7
Either the value '0', or the primary port on which a frame came from.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcBridgeRemoteMacSecondaryBVlanId		1.3.6.1.4.1.2272.1.14.21.1.8
Used to indicate the BVlan ID for this MAC address.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..4094

rcBridgeRemoteMacSecondaryDestSysName		1.3.6.1.4.1.2272.1.14.21.1.9
Secondary System name of the node where MAC address entry come from.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..255)

rcBridgeRemoteMacSecondaryPort		1.3.6.1.4.1.2272.1.14.21.1.10
Either the value '0', or the secondary port on which a frame came from.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcBridgeRemoteMacSmltRemote		1.3.6.1.4.1.2272.1.14.21.1.11
A MAC address indicate for remote learnt from ist peer
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcBootFlashSwVersion		1.3.6.1.4.1.2272.1.15.1
BootFlashSwVersion indicates the software version in the Flash.
Status: obsolete	Access: read-only
OBJECT-TYPE
	DisplayString

rcBootPcmciaSwVersion		1.3.6.1.4.1.2272.1.15.2
BootPcmciaSwVersion indicate the software version in the Pcmcia card.
Status: obsolete	Access: read-only
OBJECT-TYPE
	DisplayString

rcBootLastBootSource		1.3.6.1.4.1.2272.1.15.3
Indicates the boot source of the last the system boot.
Status: obsolete	Access: read-only
OBJECT-TYPE
	DisplayString

rcBootPrimary		1.3.6.1.4.1.2272.1.15.4
BootPrimary is indicator for the primary source to boot the system.
Status: obsolete	Access: read-write
OBJECT-TYPE
	INTEGER	flash(1), pcmcia(2), net(3), skip(4)

rcBootSecondary		1.3.6.1.4.1.2272.1.15.5
BootSecondary indicates the second choice of the boot source.
Status: obsolete	Access: read-write
OBJECT-TYPE
	INTEGER	flash(1), pcmcia(2), net(3), skip(4)

rcBootTertiary		1.3.6.1.4.1.2272.1.15.6
BootTertiary indicates the third choice of boot source.
Status: obsolete	Access: read-write
OBJECT-TYPE
	INTEGER	flash(1), pcmcia(2), net(3), skip(4)

rcDeviceLastBootSource		1.3.6.1.4.1.2272.1.16.1
Used to indicate the source of the software image the system was last booted with.
Status: deprecated	Access: read-only
OBJECT-TYPE
	DisplayString

rcDevicePrimarySource		1.3.6.1.4.1.2272.1.16.2
Used to indicate the primary choice to get a system software image.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	flash(1), pcmcia(2), net(3), skip(4)

rcDevicePrimarySourceFileName		1.3.6.1.4.1.2272.1.16.3
Used to indicate a file number, if applicable.
Status: deprecated	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

rcDeviceSecondarySource		1.3.6.1.4.1.2272.1.16.4
Used to indicate the secondary choice to get a system software image.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	flash(1), pcmcia(2), net(3), skip(4)

rcDeviceSecondarySourceFileName		1.3.6.1.4.1.2272.1.16.5
Used to indicate a file name, if applicable.
Status: deprecated	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

rcDeviceTertiarySource		1.3.6.1.4.1.2272.1.16.6
Used to indicate the tertiary choice to get a system software image.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	flash(1), pcmcia(2), net(3), skip(4)

rcDeviceTertiarySourceFileName		1.3.6.1.4.1.2272.1.16.7
Used to indicate a file name, if applicable.
Status: deprecated	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

rcDeviceConfigSource		1.3.6.1.4.1.2272.1.16.8
Used to indicate the location to get a system configuration file during system boot.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	flash(1), pcmcia(2), nvram(5)

rcDeviceConfigSourceFileName		1.3.6.1.4.1.2272.1.16.9
Used to indicate a file name, if applicable.
Status: deprecated	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

rcDeviceFlashBytesUsed		1.3.6.1.4.1.2272.1.16.10
Used to indicate the number of bytes used in the system's configuration flash device.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Integer32

rcDeviceFlashBytesFree		1.3.6.1.4.1.2272.1.16.11
Used to indicate the number of bytes available in the system's configuration flash device.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Integer32

rcDevicePcmciaBytesUsed		1.3.6.1.4.1.2272.1.16.12
Used to indicate the number of bytes used in the system's PCMCIA device.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Integer32

rcDevicePcmciaBytesFree		1.3.6.1.4.1.2272.1.16.13
Used to indicate the number of bytes available in the system's PCMCIA device.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Integer32

rcDeviceAction		1.3.6.1.4.1.2272.1.16.14
Used to specify a particular action to perform on one of the system's device.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), squeezeFlash(2), squeezePcmcia(3), formatFlash(4), formatPcmcia(5), recoverFlash(6), recoverPcmcia(7)

rcDeviceResult		1.3.6.1.4.1.2272.1.16.15
Used to indicate the result of the last action performed on one of the system's device.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), inProgress(2), success(3), fail(4)

rcDeviceFlashNumFiles		1.3.6.1.4.1.2272.1.16.16
Used to indicate the number of files available in the system's configuration flash device.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	0..128

rcDevicePcmciaNumFiles		1.3.6.1.4.1.2272.1.16.17
Used to indicate the number of files available in the system's PCMCIA device.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	0..128

rcDeviceFlashTable		1.3.6.1.4.1.2272.1.16.25
Flash table.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcDeviceFlashEntry

rcDeviceFlashEntry		1.3.6.1.4.1.2272.1.16.25.1
An entry in the system's flash table.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	RcDeviceFlashEntry

rcDeviceFlashFileNum		1.3.6.1.4.1.2272.1.16.25.1.1
Used to indicate a particular file in flash.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	0..128

rcDeviceFlashFileName		1.3.6.1.4.1.2272.1.16.25.1.2
Used to indicate a flash file's name.
Status: deprecated	Access: read-only
OBJECT-TYPE
	DisplayString

rcDeviceFlashFileVersion		1.3.6.1.4.1.2272.1.16.25.1.3
Used to indicate the flash file's version.
Status: deprecated	Access: read-only
OBJECT-TYPE
	DisplayString

rcDeviceFlashFileType		1.3.6.1.4.1.2272.1.16.25.1.4
Used to indicate the flash file's type.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	config(1), log(2), trace(3), executable(4)

rcDeviceFlashFileMode		1.3.6.1.4.1.2272.1.16.25.1.5
Used to indicate the flash file's mode.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	compressed(1), uncompressed(2)

rcDeviceFlashFileSize		1.3.6.1.4.1.2272.1.16.25.1.6
Used to indicate the flash file's size.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Integer32

rcDeviceFlashFileCrc		1.3.6.1.4.1.2272.1.16.25.1.7
Used to indicate the flash file's CRC.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Integer32

rcDeviceFlashFileStatus		1.3.6.1.4.1.2272.1.16.25.1.8
Used to indicate the flash file's status. A file that has been marked for deletion, but who's space has not been reclaimed yet is marked as 'deleted'.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	active(1), deleted(2)

rcDeviceFlashRowStatus		1.3.6.1.4.1.2272.1.16.25.1.9
Row status.
Status: deprecated	Access: read-write
OBJECT-TYPE
	RowStatus

rcDevicePcmciaTable		1.3.6.1.4.1.2272.1.16.26
PCMCIA table.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcDevicePcmciaEntry

rcDevicePcmciaEntry		1.3.6.1.4.1.2272.1.16.26.1
An entry in the system's PCMCIA table.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	RcDevicePcmciaEntry

rcDevicePcmciaFileNum		1.3.6.1.4.1.2272.1.16.26.1.1
Used to indicate a particular file in PCMCIA.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	0..128

rcDevicePcmciaFileName		1.3.6.1.4.1.2272.1.16.26.1.2
Used to indicate the PCMCIA file's name.
Status: deprecated	Access: read-only
OBJECT-TYPE
	DisplayString

rcDevicePcmciaFileVersion		1.3.6.1.4.1.2272.1.16.26.1.3
Used to indicate the PCMCIA file's version.
Status: deprecated	Access: read-only
OBJECT-TYPE
	DisplayString

rcDevicePcmciaFileType		1.3.6.1.4.1.2272.1.16.26.1.4
Used to indicate the PCMCIA file's type.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	config(1), log(2), trace(3), executable(4)

rcDevicePcmciaFileMode		1.3.6.1.4.1.2272.1.16.26.1.5
Used to indicate a particular file in mode.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	compressed(1), uncompressed(2)

rcDevicePcmciaFileSize		1.3.6.1.4.1.2272.1.16.26.1.6
Used to indicate the PCMCIA file's size.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Integer32

rcDevicePcmciaFileCrc		1.3.6.1.4.1.2272.1.16.26.1.7
Used to indicate the PCMCIA file's CRC.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Integer32

rcDevicePcmciaFileStatus		1.3.6.1.4.1.2272.1.16.26.1.8
Used to indicate the PCMCIA file's status. A file that has been marked for deletion, but who's space has not been reclaimed yet is marked as 'deleted'.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	active(1), deleted(2)

rcDevicePcmciaRowStatus		1.3.6.1.4.1.2272.1.16.26.1.9
Row status.
Status: deprecated	Access: read-write
OBJECT-TYPE
	RowStatus

rcMltNumMlts		1.3.6.1.4.1.2272.1.17.1
The number of MLTs currently defined in the switch.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcMltPotentialMembers		1.3.6.1.4.1.2272.1.17.2
The set of ports that are not members of any MLT.
Status: current	Access: read-only
OBJECT-TYPE
	PortSet

rcMltIstSessionEnable		1.3.6.1.4.1.2272.1.17.3
Used to enable/disable mlt functionality.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcMltIstSessionStatus		1.3.6.1.4.1.2272.1.17.4
Used to enable/disable mlt functionality.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2)

rcMltIstPeerIp		1.3.6.1.4.1.2272.1.17.5
IST mlt Peer Ip address.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcMltIstVlanId		1.3.6.1.4.1.2272.1.17.6
IST mlt Vlan Id.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..4095

rcMltTable		1.3.6.1.4.1.2272.1.17.10
A list of Multi-Link Trunk entries. The number of entries is given by rcMltNumMlts.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcMltEntry

rcMltEntry		1.3.6.1.4.1.2272.1.17.10.1
Entry containing configuration information for a particular Multi-Link Trunk.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcMltEntry

rcMltId		1.3.6.1.4.1.2272.1.17.10.1.1
A value that uniquely identifies the Multi-Link Trunk associated with this entry.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..256

rcMltName		1.3.6.1.4.1.2272.1.17.10.1.2
An administratively-assigned name for this MLT.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

rcMltPortMembers		1.3.6.1.4.1.2272.1.17.10.1.3
The set of ports that are members of this MLT.
Status: current	Access: read-write
OBJECT-TYPE
	PortSet

rcMltPortType		1.3.6.1.4.1.2272.1.17.10.1.4
The type of MLT port: access(1) or trunk(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	access(1), trunk(2)

rcMltNumVlanIds		1.3.6.1.4.1.2272.1.17.10.1.5
Used to indicate the number of VLAN IDs that are stored in the rcMltVlanIds variable.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcMltVlanIds		1.3.6.1.4.1.2272.1.17.10.1.6
An array used to identify which VLANs this MLT is associated with. Each VLAN ID is stored as a two octet value. The first octet in the pair holds bits 15-8 of the VLAN ID, while the second octet holds bits 7-0 of the VLAN ID. This object is now replaced by rcMltVlanIdList.
Status: deprecated	Access: read-write
OBJECT-TYPE
	IdList	Size(4096)

rcMltRowStatus		1.3.6.1.4.1.2272.1.17.10.1.7
Used to create/delete entries in the rcMltTable.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcMltEnable		1.3.6.1.4.1.2272.1.17.10.1.8
Enable the entry.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcMltLoadBalance		1.3.6.1.4.1.2272.1.17.10.1.9
Perform load balance?
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcMltDistributionAlgorithm		1.3.6.1.4.1.2272.1.17.10.1.10
none(1), ... It will be fill later
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1)

rcMltIfIndex		1.3.6.1.4.1.2272.1.17.10.1.11
Used to indicate the 'logical' ifIndex assigned to this MLT.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcMltMltType		1.3.6.1.4.1.2272.1.17.10.1.12
MLT type.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	normalMLT(1), istMLT(2), splitMLT(3)

rcMltSmltId		1.3.6.1.4.1.2272.1.17.10.1.13
Split MLT id.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..256

rcMltRunningType		1.3.6.1.4.1.2272.1.17.10.1.14
Split MLT running type.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	normalMLT(1), istMLT(2), splitMLT(3)

rcMltSvlanPortType		1.3.6.1.4.1.2272.1.17.10.1.15
Set MLT port type.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	normal(1), uni(2), nni(3)

rcMltMulticastDistribution		1.3.6.1.4.1.2272.1.17.10.1.16
Enable/Disable multicast distribution per mlt.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcMltAggregatable		1.3.6.1.4.1.2272.1.17.10.1.18
Enable/Disable link aggregation on a MLT.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcMltClearLinkAggregate		1.3.6.1.4.1.2272.1.17.10.1.19
clear link aggregate, equivalent to disable and re-enable aggregatable on the MLT.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	clear(1), none(2)

rcMltNtStgEnable		1.3.6.1.4.1.2272.1.17.10.1.20
Indicates whether this MLT is operating in Nortel Mode or in Cisco Mode. true = Nortel Mode false = Cisco Mode.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcMltDesignatedPort		1.3.6.1.4.1.2272.1.17.10.1.21
Indicates the Designated port for the MLT.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcMltAggOperState		1.3.6.1.4.1.2272.1.17.10.1.22
Link aggregation state on a MLT.
Status: current	Access: read-only
OBJECT-TYPE
	EnableValue

rcMltAggTimeOfLastOperChange		1.3.6.1.4.1.2272.1.17.10.1.23
The time value since the interface entered its current operational state.
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

rcMltAggMinLink		1.3.6.1.4.1.2272.1.17.10.1.34
If number of active links goes below configured minimum-link number, the entire LAG is declared down.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..8

rcMltVlanIdList		1.3.6.1.4.1.2272.1.17.10.1.42
This bitfield is used to identify which VLANs this MLT is associated with. Each VLAN ID is stored as a bit. The most-significant (left-most) bit represents Vlan Id 1.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..512)

rcMltMcastDistribution		1.3.6.1.4.1.2272.1.17.11
OBJECT IDENTIFIER

rcMltMcastDistributionEnable		1.3.6.1.4.1.2272.1.17.11.1
Used to enable/disable this feature to distribute multicast traffic on MLT ports. All the cards in the system must be E-Tickets. Cannot perform distribution in a mixed mode.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcMltMcastDistributionGrpMask		1.3.6.1.4.1.2272.1.17.11.2
Group Mask. Create a MLT abstraction layer to distribute traffic basd on (source, group) information of the multicast packet. The algorithm to pick the actual port nedds to generate a fairly random number for different combinations but a lways generate the same number for a given (source, group) pair. By default, the number of active ports of the MLT is used to MOD the pseudo-random number generated by the XOR of each byte of the masked group address with the masked source address.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcMltMcastDistributionSrcMask		1.3.6.1.4.1.2272.1.17.11.3
Source Mask.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcMltMcastDistributionRedistributionEnable		1.3.6.1.4.1.2272.1.17.11.4
Enable redistribution.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcSltPortTable		1.3.6.1.4.1.2272.1.17.12
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcSltPortEntry

rcMltNotificationObjects		1.3.6.1.4.1.2272.1.17.15
OBJECT IDENTIFIER

rcMltAggTrapEvent		1.3.6.1.4.1.2272.1.17.15.1
It indicates three trap events: local down(1), remote down(2), up(3).
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	INTEGER	localdown(1), remotedown(2), up(3)

rcMltIstStpEnable		1.3.6.1.4.1.2272.1.17.16
Used to enable/disable mlt ist stp functionality.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcSltPortEntry		1.3.6.1.4.1.2272.1.17.12.1
Entry containing configuration information for a particular Multi-Link Trunk.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcSltPortEntry

rcSltPortIfIndex		1.3.6.1.4.1.2272.1.17.12.1.1
An interface for this SLT.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcSltPortSmltId		1.3.6.1.4.1.2272.1.17.12.1.2
A uniquely identifies the Single-Link Trunk associated with this entry.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..512

rcSltPortOperType		1.3.6.1.4.1.2272.1.17.12.1.3
The current operate type of the port normal or smlt.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	normal(1), smlt(2)

rcSltPortRowStatus		1.3.6.1.4.1.2272.1.17.12.1.4
Used to create/delete entries of the Table.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcWebEnableServer		1.3.6.1.4.1.2272.1.18.1
Control whether the web server should be enabled. Setting this variable to true will make the server operational. Setting this variable to false will disable server.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcWebRWAUserName		1.3.6.1.4.1.2272.1.18.2
User name for the read-write-all web-server account.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(1..20)

rcWebRWAPassword		1.3.6.1.4.1.2272.1.18.3
Password for the read-write-all web-server account.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(1..20)

rcWebRWUserName		1.3.6.1.4.1.2272.1.18.4
User name for the read-write web-server account.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(1..20)

rcWebRWPassword		1.3.6.1.4.1.2272.1.18.5
Password for the read-write web-server account.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(1..20)

rcWebROUserName		1.3.6.1.4.1.2272.1.18.6
User name for the read-only web-server account.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(1..20)

rcWebROPassword		1.3.6.1.4.1.2272.1.18.7
Password for the read-only web-server account.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(1..20)

rcWebLastChange		1.3.6.1.4.1.2272.1.18.8
Last web-browser initiated configuration change since sysUpTime.
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

rcWebNumHits		1.3.6.1.4.1.2272.1.18.9
Number of hits to the web-server
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcWebNumAccessChecks		1.3.6.1.4.1.2272.1.18.10
Number of access checks performed by the web-server
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcWebNumAccessBlocks		1.3.6.1.4.1.2272.1.18.11
Number of accesses blocked by the web-server
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcWebNumRxErrors		1.3.6.1.4.1.2272.1.18.12
Number of receive errors encountered by the web-server
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcWebNumTxErrors		1.3.6.1.4.1.2272.1.18.13
Number of transmit errors encountered by the web-server
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcWebNumSetRequest		1.3.6.1.4.1.2272.1.18.14
Number of set-request to the web-server
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcWebPrimaryHtmlSourceDir		1.3.6.1.4.1.2272.1.18.15
primary html source directory
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..64)

rcWebSecondaryHtmlSourceDir		1.3.6.1.4.1.2272.1.18.16
secondary html source directory
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..64)

rcWebTertiaryHtmlSourceDir		1.3.6.1.4.1.2272.1.18.17
tertiary html source directory
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..64)

rcWebRWL3UserName		1.3.6.1.4.1.2272.1.18.18
user name for the L3 web server account
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(1..20)

rcWebRWL3Password		1.3.6.1.4.1.2272.1.18.19
password for the L3 web server account
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(1..20)

rcWebRWL2UserName		1.3.6.1.4.1.2272.1.18.20
user name for the L2 web server account
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(1..20)

rcWebRWL2Password		1.3.6.1.4.1.2272.1.18.21
password for the L2 web server account
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(1..20)

rcWebDefaultDisplayRows		1.3.6.1.4.1.2272.1.18.22
default display rows in html page.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	10..100

rcWebLastHostAccessBlocked		1.3.6.1.4.1.2272.1.18.23
last host access blocked
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcWebHelpTftpSourceDir		1.3.6.1.4.1.2272.1.18.24
tftp source directory for help files
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..256)

rcWebHttpPort		1.3.6.1.4.1.2272.1.18.25
the HTTP port for web access
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..49151

rcWebSecureOnly		1.3.6.1.4.1.2272.1.18.26
Control whether the secure only should be enabled. Setting this variable to true will make the server support HTTPS only. Setting this variable to false will make the server support both HTTP & HTTPS
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcWebHttpsPort		1.3.6.1.4.1.2272.1.18.27
the HTTPs port for web access
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	443 | 1024..49151

rcCliRWAUserName		1.3.6.1.4.1.2272.1.19.1
User name for the read-write-all CLI account.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(1..20)

rcCliRWAPassword		1.3.6.1.4.1.2272.1.19.2
Password for the read-write-all CLI account.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

rcCliRWUserName		1.3.6.1.4.1.2272.1.19.3
User name for the read-write CLI account.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(1..20)

rcCliRWPassword		1.3.6.1.4.1.2272.1.19.4
Password for the read-write CLI account.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

rcCliRWL3UserName		1.3.6.1.4.1.2272.1.19.5
User name for the read-write layer-3 CLI account.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(1..20)

rcCliRWL3Password		1.3.6.1.4.1.2272.1.19.6
Password for the read-write layer-3 CLI account.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

rcCliRWL2UserName		1.3.6.1.4.1.2272.1.19.7
User name for the read-write layer-2 CLI account.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(1..20)

rcCliRWL2Password		1.3.6.1.4.1.2272.1.19.8
Password for the read-write layer-2 CLI account.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

rcCliROUserName		1.3.6.1.4.1.2272.1.19.9
User name for the read-only CLI account.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(1..20)

rcCliROPassword		1.3.6.1.4.1.2272.1.19.10
Password for the read-only CLI account.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

rcCliMaxTelnetSessions		1.3.6.1.4.1.2272.1.19.11
Used to indicate the maximum number of telnet sessions the system will support.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..8

rcCliMaxRloginSessions		1.3.6.1.4.1.2272.1.19.12
Used to indicate the maximum number of rlogin sessions the system will support.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..8

rcCliTimeout		1.3.6.1.4.1.2272.1.19.13
Used to indicate the amount of idle time, in seconds to wait before timing out telnet and rlogin sessions.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	30..65535

rcCliNumAccessViolations		1.3.6.1.4.1.2272.1.19.14
Used to indicate the number of CLI access violations detected by the system.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcCliRWL1UserName		1.3.6.1.4.1.2272.1.19.15
User name for the read-write layer-1 CLI account.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(1..20)

rcCliRWL1Password		1.3.6.1.4.1.2272.1.19.16
Password for the read-write layer-1 CLI account.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

rcCliPasswordChange		1.3.6.1.4.1.2272.1.19.17
Used to indication which password is changed when sending a rcCliPasswordChange trap.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ro(1), l1(2), l2(3), l3(4), rw(5), rwa(6), slboper(7), l4oper(8), oper(9), slbadmin(10), l4admin(11), ssladmin(12), commStrRo(13), commStrRw(14), commStrl3(15), commStrl2(16), commStrl1(17), webPassWdRo(18), webPassWdRwa(19)

rcCliPassChangeResult		1.3.6.1.4.1.2272.1.19.18
Used to indication the result of changing password when sending a rcPasswordChange trap.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	success(1), fail(2)

rcCliRWEnable		1.3.6.1.4.1.2272.1.19.19
Enable/Disable for the read-write CLI account.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcCliRWL1Enable		1.3.6.1.4.1.2272.1.19.20
Enable/Disable for the read-write-layer1 CLI account.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcCliRWL2Enable		1.3.6.1.4.1.2272.1.19.21
Enable/Disable for the read-write-layer2 CLI account.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcCliRWL3Enable		1.3.6.1.4.1.2272.1.19.22
Enable/Disable for the read-write-layer3 CLI account.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcCliROEnable		1.3.6.1.4.1.2272.1.19.23
Enable/Disable for the read-only CLI account.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcErrorLevel		1.3.6.1.4.1.2272.1.20.1
Error level indicator for the last error reported in the system. The meaning of this value are : 0 = Informative Information 1 = Warning Condition 2 = Error Condition 3 = Manufacturing Information 4 = Fatal Condition
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcErrorCode		1.3.6.1.4.1.2272.1.20.2
Error code indicator for the last error reported in the system. This is an encoded value that identifies the software module that generated the error message as well as a specific error condition within that module. This value is transparent to the user. This value is intended to help Accelar support and development staff to isolate system problems.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcErrorText		1.3.6.1.4.1.2272.1.20.3
Error string of the last error reported in the system.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

rcIpv6Mib		1.3.6.1.4.1.2272.1.62.1
OBJECT IDENTIFIER

rcIpv6Notifications		1.3.6.1.4.1.2272.1.62.1.0
OBJECT IDENTIFIER

rcIpv6Objects		1.3.6.1.4.1.2272.1.62.1.1
OBJECT IDENTIFIER

rcIpv6Scalars		1.3.6.1.4.1.2272.1.62.1.1.1
OBJECT IDENTIFIER

rcIpv6IcmpErrorInterval		1.3.6.1.4.1.2272.1.62.1.1.1.1
The rate (in milliseconds) at which ICMP error messages can be sent out. A value of zero means not be send any.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..2147483647

rcIpv6MulticastAdminStatus		1.3.6.1.4.1.2272.1.62.1.1.1.2
This indicates the global admin status for multicast.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpv6IcmpNetUnreach		1.3.6.1.4.1.2272.1.62.1.1.1.3
Used to set icmp net unreach feature enable/ disable.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpv6IcmpRedirectMsg		1.3.6.1.4.1.2272.1.62.1.1.1.4
Used to set icmp redirect feature enable/ disable.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpv6IcmpErrorQuota		1.3.6.1.4.1.2272.1.62.1.1.1.5
The number of icmp error messages that can be sent during the icmp error interval. A value of zero means not be send any.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..2000000

rcIpv6InterfaceTable		1.3.6.1.4.1.2272.1.62.1.1.2
This table contains list of IPv6 interfaces and per-interface IPv6-specific information.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpv6InterfaceEntry

rcIpv6InterfaceEntry		1.3.6.1.4.1.2272.1.62.1.1.2.1
An entry of ipv6 interface In Table containing per-interface information.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpv6InterfaceEntry

rcIpv6InterfaceIfIndex		1.3.6.1.4.1.2272.1.62.1.1.2.1.1
An unique value to identify a physical interface or a logical interface (VLAN). For the brouter port it is the ifindex of the port and in the case of the vlan it is the ifindex of the vlan.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

rcIpv6InterfaceIdentifier		1.3.6.1.4.1.2272.1.62.1.1.2.1.2
IPv6 address interface identifiers. This is a binary string of up to 8 octets in network byte-order.
Status: current	Access: read-create
OBJECT-TYPE
	Ipv6AddressIfIdentifier

rcIpv6InterfaceIdentifierLength		1.3.6.1.4.1.2272.1.62.1.1.2.1.3
The length of the Interface Identifier in bits.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..64

rcIpv6InterfaceDescr		1.3.6.1.4.1.2272.1.62.1.1.2.1.4
A textual string containing information about the interface. This string may be set by network management system.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..255)

rcIpv6InterfaceVlanId		1.3.6.1.4.1.2272.1.62.1.1.2.1.5
A value that uniquely identifies the Virtual LAN associated with this entry. This value corresponds to the lower 12 bits in the IEEE 802.1Q VLAN Tag.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	1..4094

rcIpv6InterfaceType		1.3.6.1.4.1.2272.1.62.1.1.2.1.6
The interface type.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ethernet(1), pointToPoint(2), pointToMultipoint(3)

rcIpv6InterfaceReasmMaxSize		1.3.6.1.4.1.2272.1.62.1.1.2.1.7
MTU for this IPv6 interface, this value should be same for all the ip addresses defined on this interface.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	1280..1500 | 9600

rcIpv6InterfacePhysAddress		1.3.6.1.4.1.2272.1.62.1.1.2.1.8
The media-dependent `physical' address, for the ethernet media it is the MAC address
Status: current	Access: read-only
OBJECT-TYPE
	PhysAddress

rcIpv6InterfaceAdminStatus		1.3.6.1.4.1.2272.1.62.1.1.2.1.9
The indication of whether IPv6 is enabled (up) or disabled (down) on this interface. This object does not affect the state of the interface itself, only its connection to an IPv6 stack.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcIpv6InterfaceOperStatus		1.3.6.1.4.1.2272.1.62.1.1.2.1.10
Operating status of the interface.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2)

rcIpv6InterfaceReachableTime		1.3.6.1.4.1.2272.1.62.1.1.2.1.11
The time (in milliseconds) a neighbor is considered reachable after receiving a reachability confirmation. REFERENCE RFC2461, Section 6.3.2
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..3600000

rcIpv6InterfaceRetransmitTime		1.3.6.1.4.1.2272.1.62.1.1.2.1.12
The time (in milliseconds) between retransmissions of Neighbor Solicitation messages to a neighbor when resolving the address or when probing the reachability of a neighbor. REFERENCE RFC2461, Section 6.3.2
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..3600000

rcIpv6InterfaceMulticastAdminStatus		1.3.6.1.4.1.2272.1.62.1.1.2.1.13
This indicates the admin status for multicast for this interface.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcIpv6InterfaceRowStatus		1.3.6.1.4.1.2272.1.62.1.1.2.1.14
Row status for create/delete.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcIpv6InterfaceDhcpEnabled		1.3.6.1.4.1.2272.1.62.1.1.2.1.15
Enable or disable DHCP on the specified interface.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcIpv6InterfaceMacOffset		1.3.6.1.4.1.2272.1.62.1.1.2.1.16
Used to request a particular MAC for an IPv6 VLAN. Analogous to rcIpAdEntMacOffset in rcIpAddrTable. The system has 512 mac addresses of which 0-507 are reserved for Boardwalk box. 508-511 is reserved for MG. One can either mention a mac offset while configuring IPv6 on a vlan or it can be alloted by the system within the above range.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..65535

rcIpv6AddressTable		1.3.6.1.4.1.2272.1.62.1.1.3
This table contains addressing information relevant to the entity's interfaces. This table does not contain multicast address information. Tables for such information should be contained in multicast specific MIBs such as RFC3019. While this table is writable the user will note that several objects, such as rcIpv6AddressOrigin, are not. The intention in allowing a user to write to this table is to allow them to add or remove any entry that isn't permanent. The user should be allowed to modify objects and entries when that would not cause inconsistencies within the table. Allowing write access to objects such as rcIpv6AddressOrigin could allow a user to insert an entry and then label it incorrectly.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpv6AddressEntry

rcIpv6AddressEntry		1.3.6.1.4.1.2272.1.62.1.1.3.1
An address mapping for a particular interface. Note that when an address is added to an interface the resulted prefix is added to that interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpv6AddressEntry

rcIpv6AddressIfIndex		1.3.6.1.4.1.2272.1.62.1.1.3.1.1
The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of the IfIndex field in the rcIpv6InterfaceIfIndex.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

rcIpv6AddressAddr		1.3.6.1.4.1.2272.1.62.1.1.3.1.2
The IPv6 address to which this entry's addressing information pertains. This is one of the ipv6 addresses that this interface(identified by the rcIpv6AddressIfIndex) has. Implementors need to be aware that if the size of ipAddressAddr exceeds 116 octets then OIDS of instances of columns in this row will have more than 128 sub-identifiers and cannot be accessed using SNMPv1, SNMPv2c or SNMPv3.
Status: current	Access: not-accessible
OBJECT-TYPE
	Ipv6Address

rcIpv6AddressType		1.3.6.1.4.1.2272.1.62.1.1.3.1.3
The type of address. It is either unicast or anycast IPv6 addresses (RFC3513).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unicast(1), anycast(2)

rcIpv6AddressPrefixLength		1.3.6.1.4.1.2272.1.62.1.1.3.1.4
Prefix Length value for this address. Cannot be changed after the creation. This field MUST be provided in order to create an entry in this table.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..128

rcIpv6AddressPrefix		1.3.6.1.4.1.2272.1.62.1.1.3.1.5
A pointer to the row in the prefix table to which this address belongs. May be { 0 0 } if there is no such row.
Status: current	Access: read-only
OBJECT-TYPE
	RowPointer

rcIpv6AddressOrigin		1.3.6.1.4.1.2272.1.62.1.1.3.1.6
The origin of the address. The origin of the address, one of: other(1),manual(2), dhcp(4),linklayer(5), random(6)
Status: current	Access: read-only
OBJECT-TYPE
	IpAddressOriginTC

rcIpv6AddressStatus		1.3.6.1.4.1.2272.1.62.1.1.3.1.7
The status of the address, describing if the address can be used for communication. It will One of: preferred(1), deprecated(2),invalid(3),inaccessible(4),unknown(5), tentative(6), duplicate(7)
Status: current	Access: read-only
OBJECT-TYPE
	IpAddressStatusTC

rcIpv6AddressCreated		1.3.6.1.4.1.2272.1.62.1.1.3.1.8
The value of sysUpTime at the time this entry was created. If this entry was created prior to the last re- initialization of the local network management subsystem, then this object contains a zero value.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

rcIpv6AddressLastChanged		1.3.6.1.4.1.2272.1.62.1.1.3.1.9
The value of sysUpTime at the time this entry was last updated. If this entry was updated prior to the last re- initialization of the local network management subsystem, then this object contains a zero value.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

rcIpv6AddressRowStatus		1.3.6.1.4.1.2272.1.62.1.1.3.1.10
The status of this conceptual row. The RowStatus TC requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified. The value of this object has no effect on whether other objects in this conceptual row can be modified. A conceptual row can not be made active until the rcIpv6AddressIfIndex has been set to a valid index. Only createAndGo and Delete vlaues are supported.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcIpv6PrefixTable		1.3.6.1.4.1.2272.1.62.1.1.4
This table allows the user to determine the source of an IP address or set of IP addresses and allows other tables to share the information via pointer rather than by copying. For example when the node configures both a unicast and anycast address for a prefix the ipAddressPrefix objects for those addresses will point to a single row in this table. This table primarily provides support for IPv6 prefixes and several of the objects are less meaningful for IPv4. The table continues to allow IPv4 addresses to allow future flexibility. In order to promote a common configuration this document includes suggestions for default values for IPv4 prefixes. Each of these values may be overridden if an object is meaningful to the node. All prefixes used by this entity should be included in this table independent of how the entity learned the prefix. (This table isn't limited to prefixes learned from router advertisements.)
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpv6PrefixEntry

rcIpv6PrefixEntry		1.3.6.1.4.1.2272.1.62.1.1.4.1
An entry of ipv6 prefix In the Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpv6PrefixEntry

rcIpv6PrefixIfIndex		1.3.6.1.4.1.2272.1.62.1.1.4.1.1
An unique value to identify an ipv6 interface. For the brouter port it is the ifindex of the port and in the case of the vlan it is the ifindex of the vlan.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

rcIpv6PrefixAddr		1.3.6.1.4.1.2272.1.62.1.1.4.1.2
Prefix to create an ipv6 address in ipv6 interface table.
Status: current	Access: not-accessible
OBJECT-TYPE
	Ipv6Address

rcIpv6PrefixLength		1.3.6.1.4.1.2272.1.62.1.1.4.1.3
Mask to create an ipv6 prefix entry either will be advertised or suppressed
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..128

rcIpv6PrefixVlanId		1.3.6.1.4.1.2272.1.62.1.1.4.1.4
A value that uniquely identifies the Virtual LAN associated with this entry. This value corresponds to the lower 12 bits in the IEEE 802.1Q VLAN Tag.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4094

rcIpv6PrefixUseDefaultVal		1.3.6.1.4.1.2272.1.62.1.1.4.1.5
Select one of the value to set/use it's value to default value. This is a bitmask field, setting all the bits means that all the options will be reverted to default values.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), valid-life(2), preferred-life(3), infinite(4), no-advertise(5)

rcIpv6PrefixValidLife		1.3.6.1.4.1.2272.1.62.1.1.4.1.6
Deprecated. Use rcIpv6PrefixValidLifetime instead.
Status: deprecated	Access: read-write
OBJECT-TYPE
	Integer32	0..3600000

rcIpv6PrefixPreferredLife		1.3.6.1.4.1.2272.1.62.1.1.4.1.7
Deprecated. Use rcIpv6PrefixPreferredLifetime instead.
Status: deprecated	Access: read-write
OBJECT-TYPE
	Integer32	0..3600000

rcIpv6PrefixAtValidLife		1.3.6.1.4.1.2272.1.62.1.1.4.1.8
Is the date and time, upon reaching this value the prefix will be expired, if configured this option will be included in the neighbor advertisement for this prefix.
Status: current	Access: read-write
OBJECT-TYPE
	DateAndTime

rcIpv6PrefixAtPreferredLife		1.3.6.1.4.1.2272.1.62.1.1.4.1.9
Is the date and time, upon reaching this value the prefix will be expired, if configured this option will be included in the neighbor advertisement for this prefix.
Status: current	Access: read-write
OBJECT-TYPE
	DateAndTime

rcIpv6PrefixInfinite		1.3.6.1.4.1.2272.1.62.1.1.4.1.10
Deprecated.
Status: deprecated	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpv6PrefixOnLinkFlag		1.3.6.1.4.1.2272.1.62.1.1.4.1.11
if set then this prefix can be used for onlink determination. This value be placed in the L-bit field in the prefix information option. It is a 1 bit flag.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpv6PrefixAutoFlag		1.3.6.1.4.1.2272.1.62.1.1.4.1.12
if set then this prefix can be used for autonomous address config. This value be placed in the auto-flag field in the prefix information option. It is a 1 bit flag.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpv6PrefixAddressEui		1.3.6.1.4.1.2272.1.62.1.1.4.1.13
Use an EUI-64 interface ID in the low-order 64bits of the address when not specified in the address field. If enabled use EUI, otherwise use EUI-64 and complement U/L (Universal/Local bit). This operation should be allowed for both global and link local addresses. Once the entry is create cannot modify this field. This will be valid to use only when the PrefixLength is 64 or less
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	eui-not-used(1), eui-used-with-ul-complement(2), eui-used-without-ul-complement(3)

rcIpv6PrefixNoAdvertise		1.3.6.1.4.1.2272.1.62.1.1.4.1.14
if set then this prefix can not be included in the neighbor advertisement.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpv6PrefixRowStatus		1.3.6.1.4.1.2272.1.62.1.1.4.1.15
Row status for create/delete.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcIpv6PrefixValidLifetime		1.3.6.1.4.1.2272.1.62.1.1.4.1.16
Valid lifetime in seconds, indicates how long this prefix advertised in the nbr advertisement is valid. Value of 4294967295 represents infinity.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..4294967295

rcIpv6PrefixPreferredLifetime		1.3.6.1.4.1.2272.1.62.1.1.4.1.17
Preferred lifetime in seconds, indicates how long this prefix advertised in advertisemt for this prefix. Value of 4294967295 represents infinity.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..4294967295

rcIpv6RouterAdvertTable		1.3.6.1.4.1.2272.1.62.1.1.5
The table containing information used to construct router advertisements.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpv6RouterAdvertEntry

rcIpv6RouterAdvertEntry		1.3.6.1.4.1.2272.1.62.1.1.5.1
An entry containing information used to construct router advertisements.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpv6RouterAdvertEntry

rcIpv6RouterAdvertIfIndex		1.3.6.1.4.1.2272.1.62.1.1.5.1.1
An unique value to identify an ipv6 interface. For the brouter port it is the ifindex of the port and in the case of the vlan it is the ifindex of the vlan.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

rcIpv6RouterAdvertSendAdverts		1.3.6.1.4.1.2272.1.62.1.1.5.1.2
A flag indicating whether or not the router sends periodic router advertisements and responds to router solicitations on this interface. REFERENCE RFC2461 Section 6.2.1
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpv6RouterAdvertUseDefaultVal		1.3.6.1.4.1.2272.1.62.1.1.5.1.3
Select one of the value to set/use it's value to default value, or set all the bits to indicate all the options will be set to their default value.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), send-advertisement(2), max-interval(3), min-interval(4), default-life-time(5), hop-limit(6), managed-flag(7), other-config-flag(8), dad-ns-num(9)

rcIpv6RouterAdvertMaxInterval		1.3.6.1.4.1.2272.1.62.1.1.5.1.4
Configure the max interval (in seconds) at which the transmission of route advertisments can occur on this interface. This must be no less than 4 seconds and no greater than 1800.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	4..1800

rcIpv6RouterAdvertMinInterval		1.3.6.1.4.1.2272.1.62.1.1.5.1.5
Configure the min interval (in seconds) at which the transmission of route advertisments can occur on this interface. This must be no less than 3 seconds and no greater than .75* max-interval.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	3..1350

rcIpv6RouterAdvertReachableTime		1.3.6.1.4.1.2272.1.62.1.1.5.1.6
The value (in milliseconds) to be placed in the router advertisement message sent by the router. The value zero means unspecified (by this router). Used to configure the amount of time that a remote IPv6 node is considered reachable after some reachability confirmation event has occured. REFERENCE RFC2461 Section 6.2.1
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..36000000

rcIpv6RouterAdvertRetransmitTimer		1.3.6.1.4.1.2272.1.62.1.1.5.1.7
The value (in milliseconds) to be placed in the retransmit timer field in router advertisement message sent from this interface. The value zero means unspecified (by this router). Used to configure the amount of time that router should wait for the transmit to occur. REFERENCE RFC2461 Section 6.2.1
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..36000000

rcIpv6RouterAdvertDefaultLifeTime		1.3.6.1.4.1.2272.1.62.1.1.5.1.8
The value to be placed in the router lifetime field of router advertisements sent from this interface. This value MUST be either 0 or between rcIpv6RouterAdvertMaxInterval and 9000 seconds. A value of zero indicates that the router is not to be used as a default router. The default is 3 * rcIpv6RouterAdvertMaxInterval. REFERENCE RFC2461 Section 6.2.1
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0 | 4..9000

rcIpv6RouterAdvertCurHopLimit		1.3.6.1.4.1.2272.1.62.1.1.5.1.9
The default value to be placed in the current hop limit field in router advertisements sent from this interface. The value should be set to the current diameter of the Internet. A value of zero in the router advertisement indicates that the advertisement isn't specifying a value for curHopLimit. The default should be set to the value specified in the IANA web pages (www.iana.org) at the time of implementation. REFERENCE RFC2461 Section 6.2.1
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..255

rcIpv6RouterAdvertManagedFlag		1.3.6.1.4.1.2272.1.62.1.1.5.1.10
if true then the M-bit(Managed address configureation) in the router adverisement will be set. REFERENCE RFC2461 Section 6.2.1
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpv6RouterAdvertOtherConfigFlag		1.3.6.1.4.1.2272.1.62.1.1.5.1.11
if true then the O-bit (Other stateful Configuration) in the router adverisement will be set. REFERENCE RFC2461 Section 6.2.1
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpv6RouterAdvertDadNsNum		1.3.6.1.4.1.2272.1.62.1.1.5.1.12
The number of neighbor solicitation messages for DAD (Duplicate address detection). A value 0 is used to disable DAD process on this interface. A value 1 is used to send one advertisment without any retransmissions.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..600

rcIpv6RouterAdvertLinkMTU		1.3.6.1.4.1.2272.1.62.1.1.5.1.13
The value to be placed in MTU options sent by the router on this interface. A value of zero indicates that no MTU options are sent. REFERENCE RFC2461 Section 6.2.1
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcIpv6StaticRouteTable		1.3.6.1.4.1.2272.1.62.1.1.6
This table contains list of routes that are created by the user to destination networks.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpv6StaticRouteEntry

rcIpv6StaticRouteEntry		1.3.6.1.4.1.2272.1.62.1.1.6.1
An entry in the static route table for IPv6 can be created for a destination with a specific prefix length; multiple entries to the same destination are created either by specifying the next-hop or interfaceIndex or both to reach the destination. However if the nexthop Ipv6 address is a link-local address then IfIndex must be supplied.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpv6StaticRouteEntry

rcIpv6StaticRouteDest		1.3.6.1.4.1.2272.1.62.1.1.6.1.1
The destination IPv6 address of this route. The values for the index objects rcIpv6StaticRouteDest and rcIpv6StaticRoutePrefixLength must be consistent. When the value of rcIpv6StaticRouteDest (excluding the zone index, if one is present) is x, then the bitwise logical-AND of x with the value of the mask formed from the corresponding index object rcIpv6StaticRoutePrefixLength MUST be equal to x. If not, then the index pair is not consistent and an inconsistentName error must be returned on SET or CREATE requests.
Status: current	Access: not-accessible
OBJECT-TYPE
	Ipv6Address

rcIpv6StaticRoutePrefixLength		1.3.6.1.4.1.2272.1.62.1.1.6.1.2
Indicates the number of leading one bits which form the mask to be logical-ANDed with the destination address before being compared to the value in the rcIpv6StaticRouteDestAddr field.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..128

rcIpv6StaticRouteNextHop		1.3.6.1.4.1.2272.1.62.1.1.6.1.3
Next hop IPv6 address for this destination. On remote routes, the address of the next system en route. For non-remote routes, a zero length string.
Status: current	Access: not-accessible
OBJECT-TYPE
	Ipv6Address

rcIpv6StaticRouteIfIndex		1.3.6.1.4.1.2272.1.62.1.1.6.1.4
The ifIndex value which identifies the local interface through which the next hop of this route should be reached. A value of 0 is valid and represents the scenario where no interface is specified.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

rcIpv6StaticRouteDistance		1.3.6.1.4.1.2272.1.62.1.1.6.1.5
cost/distance to reach the destination for this node.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

rcIpv6StaticRouteStatus		1.3.6.1.4.1.2272.1.62.1.1.6.1.6
(1)notReachable means the route is not reachable and no neighbor request entry is built to resolved the next-hop. It happens when there is no route or neighbor to reach the static route's next-hop. (2)tryToResolve means the route is not reachable but a neighbor request entry is built to resolved the next-hop. It happens when there is a local equivelent route in system to reach the next-hop but the neighor is not learnt yet (3)reachableNotInRtm means the static route is reachable but it is not in RTM. It happens when the static route is reachable, but it is not the best among alternative static route. (4)reachableInRtm means the static route is reachable and it is in RTM. It happens when the static route is reachable, and it is the best among alternative static route to be added into RTM.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notReachable(1), tryToResolve(2), reachableNotInRtm(3), reachableInRtm(4)

rcIpv6StaticRoutePreference		1.3.6.1.4.1.2272.1.62.1.1.6.1.7
Used to indicate the route preference of this entry. If there are more than one route that can be used to forward IP traffic, the route that has a highest preference will be used instead of a lower preference one. The higher the number, the higher the preference.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..255

rcIpv6StaticRouteEnable		1.3.6.1.4.1.2272.1.62.1.1.6.1.8
Used to enable/disable this entry.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpv6StaticRouteRowStatus		1.3.6.1.4.1.2272.1.62.1.1.6.1.9
Row status for create/delete.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcIpv6NetToPhysicalTable		1.3.6.1.4.1.2272.1.62.1.1.7
The IP Address Translation table used for mapping from IP addresses to physical addresses. The Address Translation tables contain the IP address to 'physical' address equivalences. Some interfaces do not use translation tables for determining address equivalences (e.g., DDN-X.25 has an algorithmic method); if all interfaces are of this type, then the Address Translation table is empty, i.e., has zero entries. While many protocols may be used to populate this table, ARP [10] and Neighbor Discovery [4] are the most likely options.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpv6NetToPhysicalEntry

rcIpv6NetToPhysicalEntry		1.3.6.1.4.1.2272.1.62.1.1.7.1
Each entry contains one IP address to `physical' address equivalence.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpv6NetToPhysicalEntry

rcIpv6NetToPhysicalIfIndex		1.3.6.1.4.1.2272.1.62.1.1.7.1.1
The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of the IfIndex field in the rcIpv6InterfaceIfIndex.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

rcIpv6NetToPhysicalNetAddress		1.3.6.1.4.1.2272.1.62.1.1.7.1.2
The IP Address corresponding to the media-dependent `physical' address. The address type of this object is specified in rcIpv6NetToPhysicalAddressType. Implementors need to be aware that if the size of rcIpv6NetToPhysicalNetAddress exceeds 115 octets then OIDS of instances of columns in this row will have more than 128 sub-identifiers and cannot be accessed using SNMPv1, SNMPv2c or SNMPv3.
Status: current	Access: not-accessible
OBJECT-TYPE
	Ipv6Address

rcIpv6NetToPhysicalPhysAddress		1.3.6.1.4.1.2272.1.62.1.1.7.1.3
The media-dependent `physical' address. As the entries in this table are typically not persistent when this object is written the entity SHOULD NOT save the change to non-volatile storage. In the ethernet case it is a MAC address.
Status: current	Access: read-write
OBJECT-TYPE
	PhysAddress	Size(0..65535)

rcIpv6NetToPhysicalInterface		1.3.6.1.4.1.2272.1.62.1.1.7.1.4
The field represents either a physical port id or the MLT port id. This entry is associated either with a port or with a MLT in a VLAN/Brouter port. If the value is 0 then the interface is CP port.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcIpv6NetToPhysicalLastUpdated		1.3.6.1.4.1.2272.1.62.1.1.7.1.5
The value of sysUpTime at the time this entry was last updated. If this entry was updated prior to the last re- initialization of the local network management subsystem, then this object contains a zero value.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

rcIpv6NetToPhysicalType		1.3.6.1.4.1.2272.1.62.1.1.7.1.6
The type of mapping. The 'dynamic(2)' type indicates that the IP address to physical addresses mapping has been dynamically resolved using e.g. IPv4 ARP or the IPv6 Neighbor Discovery protocol. The 'static(3)' type indicates that the mapping has been statically configured. Both of these refer to entries that provide mappings for other entities addresses. The 'local(4)' type indicates that the mapping is provided for an entity's own interface address. As the entries in this table are typically not persistent when this object is written the entity SHOULD NOT save the change to non-volatile storage.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), dynamic(2), static(3), local(4)

rcIpv6NetToPhysicalState		1.3.6.1.4.1.2272.1.62.1.1.7.1.8
The Neighbor Unreachability Detection [4] state for the interface when the address mapping in this entry is used. If Neighbor Unreachability Detection is not in use (eg. for IPv4), this object is always unknown(6). REFERENCE RFC2461
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	reachable(1), stale(2), delay(3), probe(4), invalid(5), unknown(6), incomplete(7)

rcIpv6NetToPhysicalRowStatus		1.3.6.1.4.1.2272.1.62.1.1.7.1.9
The status of this conceptual row. The RowStatus TC requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified. The value of this object has no effect on whether other objects in this conceptual row can be modified. A conceptual row can not be made active until the rcIpv6NetToPhysicalPhysAddress object has been set. Note that if the rcIpv6NetToPhysicalType is set to 'invalid' the managed node may delete the entry independent of the state of this object. Only createandGo and Delete operations are supported
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcIpv6PrefixListTableSize		1.3.6.1.4.1.2272.1.62.1.1.1.8
Size of Ipv6 Prefix List Table
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcIpv6PrefixListTable		1.3.6.1.4.1.2272.1.62.1.1.8
IPv6 Prefix List table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpv6PrefixListEntry

rcIpv6PrefixListEntry		1.3.6.1.4.1.2272.1.62.1.1.8.1
An entry of Ipv6 Prefix List Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpv6PrefixListEntry

rcIpv6PrefixListId		1.3.6.1.4.1.2272.1.62.1.1.8.1.1
Id of an IPv6 Prefix List
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	0..2147483647

rcIpv6PrefixListPrefix		1.3.6.1.4.1.2272.1.62.1.1.8.1.2
Is a member of a specific ipv6 prefix list. Adding the prefix to the given ipv6 prefix list
Status: current	Access: not-accessible
OBJECT-TYPE
	Ipv6Address

rcIpv6PrefixListPrefixMaskLen		1.3.6.1.4.1.2272.1.62.1.1.8.1.3
Mask length of the ipv6 prefix added to the prefix list
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	0..128

rcIpv6PrefixListMaskLenFrom		1.3.6.1.4.1.2272.1.62.1.1.8.1.4
Lower bound of mask length of the ipv6 prefix added to the prefix list
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..128

rcIpv6PrefixListMaskLenUpto		1.3.6.1.4.1.2272.1.62.1.1.8.1.5
Higher bound of mask length of the ipv6 prefix added to the prefix list
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..128

rcIpv6PrefixListName		1.3.6.1.4.1.2272.1.62.1.1.8.1.6
Name of the Ipv6 prefix list
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString	Size(1..64)

rcIpv6PrefixListRowStatus		1.3.6.1.4.1.2272.1.62.1.1.8.1.7
Used to create/delete entries in the ipv6 prefix list table
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcOspfv3Mib		1.3.6.1.4.1.2272.1.67.1
OBJECT IDENTIFIER

rcOspfv3Objects		1.3.6.1.4.1.2272.1.67.1.1
OBJECT IDENTIFIER

rcOspfv3Conformance		1.3.6.1.4.1.2272.1.67.1.2
OBJECT IDENTIFIER

rcOspfv3GeneralGroup		1.3.6.1.4.1.2272.1.67.1.1.1
OBJECT IDENTIFIER

rcOspfv3RouterId		1.3.6.1.4.1.2272.1.67.1.1.1.1
A 32-bit integer uniquely identifying the router in the Autonomous System. To ensure uniqueness, this may default to the value of one of the router's IPv4 interface addresses if IPv4 is configured on the router.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcOspfv3AdminStat		1.3.6.1.4.1.2272.1.67.1.1.1.2
The administrative status of OSPFv3 in the router. The value 'enabled' denotes that the OSPFv3 Process is active on at least one inter- face; 'disabled' disables it on all inter- faces.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

rcOspfv3VersionNumber		1.3.6.1.4.1.2272.1.67.1.1.1.3
The version number of OSPF for IPv6 is 3.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	version3(3)

rcOspfv3AreaBdrRtrStatus		1.3.6.1.4.1.2272.1.67.1.1.1.4
A flag to note whether this router is an area border router.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcOspfv3ASBdrRtrStatus		1.3.6.1.4.1.2272.1.67.1.1.1.5
A flag to note whether this router is config- ured as an Autonomous System border router.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcOspfv3AsScopeLsaCount		1.3.6.1.4.1.2272.1.67.1.1.1.6
The number of AS-Scope (e.g. AS-External) link-state advertisements in the link-state database.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcOspfv3AsScopeLsaCksumSum		1.3.6.1.4.1.2272.1.67.1.1.1.7
The 32-bit unsigned sum of the LS checksums of the AS-scoped link-state advertisements con- tained in the link-state database. This sum can be used to determine if there has been a change in a router's link state database, and to compare the link-state database of two routers.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcOspfv3OriginateNewLsas		1.3.6.1.4.1.2272.1.67.1.1.1.8
The number of new link-state advertisements that have been originated. This number is in- cremented each time the router originates a new LSA.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcOspfv3RxNewLsas		1.3.6.1.4.1.2272.1.67.1.1.1.9
The number of link-state advertisements re- ceived determined to be new instantiations. This number does not include newer instantia- tions of self-originated link-state advertise- ments.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcOspfv3ExtLsaCount		1.3.6.1.4.1.2272.1.67.1.1.1.10
The number of External(LS type 0x4005) in the link- state database
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcOspfv3ExtAreaLsdbLimit		1.3.6.1.4.1.2272.1.67.1.1.1.11
The maximum number of non-default AS- external-LSAs entries that can be stored in the link-state database. If the value is -1, then there is no limit. When the number of non-default AS-external-LSAs in a router's link-state database reaches rcOspfv3ExtAreaLsdbLimit, the router enters Overflow- State. The router never holds more than rcOspfv3ExtAreaLsdbLimit non-default AS-external-LSAs in its database. OspfExtAreaLsdbLimit MUST be set identically in all routers attached to the OSPFv3 backbone and/or any regular OSPFv3 area. (i.e., OSPFv3 stub areas and NSSAs are excluded).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..7FFFFFFF

rcOspfv3MulticastExtensions		1.3.6.1.4.1.2272.1.67.1.1.1.12
A Bit Mask indicating whether the router is forwarding IPv6 multicast datagrams based on the algorithms defined in the Multi- cast Extensions to OSPF. If intraAreaMulticast set, indicates that the router can forward IPv6 multicast datagrams in the router's directly attached areas (called intra-area mul- ticast routing). If interAreaMulticast set, indicates that the router can forward IPv6 multicast datagrams between OSPFv3 areas (called inter-area multicast routing). If interAsMulticast set, indicates that the router can forward IPv6 multicast datagrams between Auto- nomous Systems (called inter-AS multicast rout- ing). Only certain combinations of bit settings are allowed, namely: - All bits cleared (no multicasting) - intraAreaMulticast only, - intraAreaMulticast and interAreaMulticast, - intraAreaMulticast and interAsMulticast - intraAreaMulticast, interAreaMulticast and interAsMulticast By default, all bits are cleared.
Status: current	Access: read-write
OBJECT-TYPE
	BITS	intraAreaMulticast(0), interAreaMulticast(1), interAsMulticast(2)

rcOspfv3ExitOverflowInterval		1.3.6.1.4.1.2272.1.67.1.1.1.13
The number of seconds that, after entering OverflowState, a router will attempt to leave OverflowState. This allows the router to again originate non-default AS-External-LSAs. When set to 0, the router will not leave Overflow- State until restarted.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

rcOspfv3DemandExtensions		1.3.6.1.4.1.2272.1.67.1.1.1.14
The router's support for demand routing.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcOspfv3TrafficEngineeringSupport		1.3.6.1.4.1.2272.1.67.1.1.1.15
The router's support for traffic engineering extensions.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcOspfv3ReferenceBandwidth		1.3.6.1.4.1.2272.1.67.1.1.1.16
Reference bandwidth in kilobits/second for calculating default interface metrics. The default value is 100,000 KBPS (100 MBPS)
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

rcOspfv3RestartSupport		1.3.6.1.4.1.2272.1.67.1.1.1.17
The router's support for OSPF hitless restart. Options include: no restart support, only planned restarts or both planned and unplanned restarts.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), plannedOnly(2), plannedAndUnplanned(3)

rcOspfv3RestartInterval		1.3.6.1.4.1.2272.1.67.1.1.1.18
Configured OSPF hitless restart timeout interval.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..1800

rcOspfv3RestartStatus		1.3.6.1.4.1.2272.1.67.1.1.1.19
Current status of OSPF hitless restart.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notRestarting(1), plannedRestart(2), unplannedRestart(3)

rcOspfv3RestartAge		1.3.6.1.4.1.2272.1.67.1.1.1.20
Remaining time in current OSPF hitless restart interval.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..1800

rcOspfv3RestartExitReason		1.3.6.1.4.1.2272.1.67.1.1.1.21
Describes the outcome of the last attempt at a hitless restart. If the value is 'none', no restart has yet been attempted. If the value is 'inProgress', a restart attempt is currently underway.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), inProgress(2), completed(3), timedOut(4), topologyChanged(5)

rcOspfv3BadLsaIgnore		1.3.6.1.4.1.2272.1.67.1.1.1.22
The administrative status of OSPFv3 in the router. The value 'enabled' denotes that the OSPFv3 Process is active on at least one inter- face; 'disabled' disables it on all inter- faces.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

rcOspfv3AreaTable		1.3.6.1.4.1.2272.1.67.1.1.2
Information describing the configured parame- ters and cumulative statistics of the router's attached areas.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcOspfv3AreaEntry

rcOspfv3AreaEntry		1.3.6.1.4.1.2272.1.67.1.1.2.1
Information describing the configured parame- ters and cumulative statistics of one of the router's attached areas.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcOspfv3AreaEntry

rcOspfv3AreaId		1.3.6.1.4.1.2272.1.67.1.1.2.1.1
A 32-bit integer uniquely identifying an area. Area ID 0.0.0.0 is used for the OSPFv3 backbone.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rcOspfv3ImportAsExtern		1.3.6.1.4.1.2272.1.67.1.1.2.1.2
Indicates whether an area is a Stub area, NSSA, or standard area. AS-scope LSAs are not imported into Stub Areas or NSSAs. NSSAs import AS-External data as Type-7 LSAs which have Area-scope
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	importExternal(1), importNoExternal(2), importNssa(3)

rcOspfv3AreaSpfRuns		1.3.6.1.4.1.2272.1.67.1.1.2.1.3
The number of times that the intra-area route table has been calculated using this area's link-state database. This is typically done using Dijkstra's algorithm.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcOspfv3AreaBdrRtrCount		1.3.6.1.4.1.2272.1.67.1.1.2.1.4
The total number of area border routers reach- able within this area. This is initially zero, and is calculated in each SPF Pass.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcOspfv3AreaAsBdrRtrCount		1.3.6.1.4.1.2272.1.67.1.1.2.1.5
The total number of Autonomous System border routers reachable within this area. This is initially zero, and is calculated in each SPF Pass.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcOspfv3AreaScopeLsaCount		1.3.6.1.4.1.2272.1.67.1.1.2.1.6
The total number of Area-Scope link-state advertisements in this area's link-state database.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcOspfv3AreaScopeLsaCksumSum		1.3.6.1.4.1.2272.1.67.1.1.2.1.7
The 32-bit unsigned sum of the Area-Scope link-state advertisements' LS checksums contained in this area's link-state database. The sum can be used to determine if there has been a change in a router's link state database, and to compare the link-state database of two routers.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcOspfv3AreaSummary		1.3.6.1.4.1.2272.1.67.1.1.2.1.8
The variable rcOspfv3AreaSummary controls the im- port of Inter-Area LSAs into stub areas. It has no effect on other areas. If it is noAreaSummary, the router will neither originate nor propagate Inter-Area LSAs into the stub area. It will rely entirely on its de- fault route. If it is sendAreaSummary, the router will both summarize and propagate Inter-Area LSAs.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noAreaSummary(1), sendAreaSummary(2)

rcOspfv3AreaStatus		1.3.6.1.4.1.2272.1.67.1.1.2.1.9
This variable controls the status of the en- try. The use of RowStatus is covered in more detail in [6].
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcOspfv3StubMetric		1.3.6.1.4.1.2272.1.67.1.1.2.1.10
The metric value advertised for the default route into Stub and NSSA areas.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..FFFFFF

rcOspfv3AreaNssaTranslatorRole		1.3.6.1.4.1.2272.1.67.1.1.2.1.11
Indicates an NSSA Border router's ability to perform NSSA translation of type-7 LSAs into type-5 LSAs.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	always(1), candidate(2)

rcOspfv3AreaNssaTranslatorState		1.3.6.1.4.1.2272.1.67.1.1.2.1.12
Indicates if and how an NSSA Border router is performing NSSA translation of type-7 LSAs into type-5 LSAs. When this object is set to enabled, the NSSA Border router's rcOspfv3AreaNssTranslatorRole has been set to always. When this object is set to elected, a candidate NSSA Border router is translating type-7 LSAs into type-5. When this object is set to disabled, a candidate NSSA Border router is NOT translating type-7 LSAs into type-5.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	enabled(1), elected(2), disabled(3)

rcOspfv3AreaNssaTranslatorStabilityInterval		1.3.6.1.4.1.2272.1.67.1.1.2.1.13
The number of seconds after an elected translator determines its services are no longer required, that it should continue to perform its translation duties.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

rcOspfv3AreaNssaTranslatorEvents		1.3.6.1.4.1.2272.1.67.1.1.2.1.14
Indicates the number of Translator State changes that have occurred since the last boot-up.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcOspfv3AreaStubMetricType		1.3.6.1.4.1.2272.1.67.1.1.2.1.15
This variable displays the type of metric ad- vertised as a default route.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ospfv3Metric(1), comparableCost(2), nonComparable(3)

rcOspfv3AsLsdbTable		1.3.6.1.4.1.2272.1.67.1.1.3
The OSPFv3 Process's AS-Scope Link State Database.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcOspfv3AsLsdbEntry

rcOspfv3AsLsdbEntry		1.3.6.1.4.1.2272.1.67.1.1.3.1
A single AS-Scope Link State Advertisement.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcOspfv3AsLsdbEntry

rcOspfv3AsLsdbType		1.3.6.1.4.1.2272.1.67.1.1.3.1.1
The type of the link state advertisement. Each link state type has a separate advertise- ment format. AS-Scope LSAs not recognized by the router may be stored in the database.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	linkLsa(8), routerLink(8193), networkLink(8194), interAreaPrefix(8195), interAreaRouter(8196), type7(8199), intraAreaPrefix(8201), asExternal(16389)

rcOspfv3AsLsdbRouterId		1.3.6.1.4.1.2272.1.67.1.1.3.1.2
The 32 bit number that uniquely identifies the originating router in the Autonomous System.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rcOspfv3AsLsdbLsid		1.3.6.1.4.1.2272.1.67.1.1.3.1.3
The Link State ID is an LS Type Specific field containing a unique identifier; it identifies the piece of the routing domain that is being described by the advertisement. In contrast to OSPFv2, the LSID has no addressing semantics.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

rcOspfv3AsLsdbSequence		1.3.6.1.4.1.2272.1.67.1.1.3.1.4
The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcOspfv3AsLsdbAge		1.3.6.1.4.1.2272.1.67.1.1.3.1.5
This field is the age of the link state adver- tisement in seconds.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcOspfv3AsLsdbChecksum		1.3.6.1.4.1.2272.1.67.1.1.3.1.6
This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connec- tionless datagrams; it is commonly referred to as the Fletcher checksum.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcOspfv3AsLsdbAdvertisement		1.3.6.1.4.1.2272.1.67.1.1.3.1.7
The entire Link State Advertisement, including its header.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(1..65535)

rcOspfv3AsLsdbTypeKnown		1.3.6.1.4.1.2272.1.67.1.1.3.1.8
Is the LSA type recognized by this Router?
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcOspfv3AreaLsdbTable		1.3.6.1.4.1.2272.1.67.1.1.4
The OSPFv3 Process's Area-Scope Link State Database.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcOspfv3AreaLsdbEntry

rcOspfv3AreaLsdbEntry		1.3.6.1.4.1.2272.1.67.1.1.4.1
A single Area-Scope Link State Advertisement.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcOspfv3AreaLsdbEntry

rcOspfv3AreaLsdbAreaId		1.3.6.1.4.1.2272.1.67.1.1.4.1.1
The 32 bit identifier of the Area from which the LSA was received.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rcOspfv3AreaLsdbType		1.3.6.1.4.1.2272.1.67.1.1.4.1.2
The type of the link state advertisement. Each link state type has a separate advertise- ment format. Area-Scope LSAs unrecognized by the router are also stored in this database.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	linkLsa(8), routerLink(8193), networkLink(8194), interAreaPrefix(8195), interAreaRouter(8196), type7(8199), intraAreaPrefix(8201), asExternal(16389)

rcOspfv3AreaLsdbRouterId		1.3.6.1.4.1.2272.1.67.1.1.4.1.3
The 32 bit number that uniquely identifies the originating router in the Autonomous System.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rcOspfv3AreaLsdbLsid		1.3.6.1.4.1.2272.1.67.1.1.4.1.4
The Link State ID is an LS Type Specific field containing a unique identifier; it identifies the piece of the routing domain that is being described by the advertisement. In contrast to OSPFv2, the LSID has no addressing semantics.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

rcOspfv3AreaLsdbSequence		1.3.6.1.4.1.2272.1.67.1.1.4.1.5
The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcOspfv3AreaLsdbAge		1.3.6.1.4.1.2272.1.67.1.1.4.1.6
This field is the age of the link state adver- tisement in seconds.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcOspfv3AreaLsdbChecksum		1.3.6.1.4.1.2272.1.67.1.1.4.1.7
This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connec- tionless datagrams; it is commonly referred to as the Fletcher checksum.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcOspfv3AreaLsdbAdvertisement		1.3.6.1.4.1.2272.1.67.1.1.4.1.8
The entire Link State Advertisement, including its header.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(1..65535)

rcOspfv3AreaLsdbTypeKnown		1.3.6.1.4.1.2272.1.67.1.1.4.1.9
Is the LSA type recognized by this Router?
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcOspfv3LinkLsdbTable		1.3.6.1.4.1.2272.1.67.1.1.5
The OSPFv3 Process's Link-Scope Link State Database.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcOspfv3LinkLsdbEntry

rcOspfv3LinkLsdbEntry		1.3.6.1.4.1.2272.1.67.1.1.5.1
A single Link-Scope Link State Advertisement.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcOspfv3LinkLsdbEntry

rcOspfv3LinkLsdbIfIndex		1.3.6.1.4.1.2272.1.67.1.1.5.1.1
The identifier of the link from which the LSA was received.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

rcOspfv3LinkLsdbType		1.3.6.1.4.1.2272.1.67.1.1.5.1.2
The type of the link state advertisement. Each link state type has a separate advertise- ment format. Link-Scope LSAs unrecognized by the router are also stored in this database.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	linkLsa(8), routerLink(8193), networkLink(8194), interAreaPrefix(8195), interAreaRouter(8196), type7(8199), intraAreaPrefix(8201), asExternal(16389)

rcOspfv3LinkLsdbRouterId		1.3.6.1.4.1.2272.1.67.1.1.5.1.3
The 32 bit number that uniquely identifies the originating router in the Autonomous System.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rcOspfv3LinkLsdbLsid		1.3.6.1.4.1.2272.1.67.1.1.5.1.4
The Link State ID is an LS Type Specific field containing a unique identifier; it identifies the piece of the routing domain that is being described by the advertisement. In contrast to OSPFv2, the LSID has no addressing semantics.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

rcOspfv3LinkLsdbSequence		1.3.6.1.4.1.2272.1.67.1.1.5.1.5
The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcOspfv3LinkLsdbAge		1.3.6.1.4.1.2272.1.67.1.1.5.1.6
This field is the age of the link state advertisement in seconds.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcOspfv3LinkLsdbChecksum		1.3.6.1.4.1.2272.1.67.1.1.5.1.7
This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connec- tionless datagrams; it is commonly referred to as the Fletcher checksum.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcOspfv3LinkLsdbAdvertisement		1.3.6.1.4.1.2272.1.67.1.1.5.1.8
The entire Link State Advertisement, including its header.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(1..65535)

rcOspfv3LinkLsdbTypeKnown		1.3.6.1.4.1.2272.1.67.1.1.5.1.9
Indicates whether the LSA type is recognized by this Router.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcOspfv3HostTable		1.3.6.1.4.1.2272.1.67.1.1.6
The list of Hosts, and their metrics, that the router will advertise as host routes.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcOspfv3HostEntry

rcOspfv3HostEntry		1.3.6.1.4.1.2272.1.67.1.1.6.1
A metric to be advertised when a given host is reachable.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcOspfv3HostEntry

rcOspfv3HostAddressType		1.3.6.1.4.1.2272.1.67.1.1.6.1.1
The address type of rcOspfv3HostAddress. Only IPv6 addresses without zone index are expected.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	unknown(0), ipv4(1), ipv6(2), ipv4z(3), ipv6z(4), dns(16)

rcOspfv3HostAddress		1.3.6.1.4.1.2272.1.67.1.1.6.1.2
The IPv6 Address of the Host. Must be a Global or Site-local address.
Status: current	Access: not-accessible
OBJECT-TYPE
	OCTET STRING	Size(16)

rcOspfv3HostMetric		1.3.6.1.4.1.2272.1.67.1.1.6.1.3
The Metric to be advertised.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..FFFF

rcOspfv3HostStatus		1.3.6.1.4.1.2272.1.67.1.1.6.1.4
This variable controls the status of the en- try. The use of RowStatus is covered in more detail in [6].
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcOspfv3HostAreaID		1.3.6.1.4.1.2272.1.67.1.1.6.1.5
The Area the Host Entry is to be found within. By default, the area that a subsuming OSPFv3 in- terface is in, or 0.0.0.0
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcOspfv3IfTable		1.3.6.1.4.1.2272.1.67.1.1.7
The OSPFv3 Interface Table describes the inter- faces from the viewpoint of OSPFv3.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcOspfv3IfEntry

rcOspfv3IfEntry		1.3.6.1.4.1.2272.1.67.1.1.7.1
The OSPFv3 Interface Entry describes one inter- face from the viewpoint of OSPFv3.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcOspfv3IfEntry

rcOspfv3IfIndex		1.3.6.1.4.1.2272.1.67.1.1.7.1.1
The interface index of this OSPFv3 interface. It corresponds to the interface index of the IPv6 interface on which OSPFv3 is configured.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

rcOspfv3IfAreaId		1.3.6.1.4.1.2272.1.67.1.1.7.1.2
A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0.0.0.0 is used for the OSPFv3 backbone.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcOspfv3IfType		1.3.6.1.4.1.2272.1.67.1.1.7.1.3
The OSPFv3 interface type.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	broadcast(1), nbma(2), pointToPoint(3), pointToMultipoint(5)

rcOspfv3IfAdminStat		1.3.6.1.4.1.2272.1.67.1.1.7.1.4
The OSPFv3 interface's administrative status. The value formed on the interface, and the in- terface will be advertised as an internal route to some area. The value 'disabled' denotes that the interface is external to OSPFv3.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

rcOspfv3IfRtrPriority		1.3.6.1.4.1.2272.1.67.1.1.7.1.5
The priority of this interface. Used in multi-access networks, this field is used in the designated router election algorithm. The value 0 signifies that the router is not eligi- ble to become the designated router on this particular network. In the event of a tie in this value, routers will use their Router ID as a tie breaker.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..FF

rcOspfv3IfTransitDelay		1.3.6.1.4.1.2272.1.67.1.1.7.1.6
The estimated number of seconds it takes to transmit a link state update packet over this interface.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..1800

rcOspfv3IfRetransInterval		1.3.6.1.4.1.2272.1.67.1.1.7.1.7
The number of seconds between link-state ad- vertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database descrip- tion and link-state request packets.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..1800

rcOspfv3IfHelloInterval		1.3.6.1.4.1.2272.1.67.1.1.7.1.8
The length of time, in seconds, between the Hello packets that the router sends on the in- terface. This value must be the same for all routers attached to a common network.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..FFFF

rcOspfv3IfRtrDeadInterval		1.3.6.1.4.1.2272.1.67.1.1.7.1.9
The number of seconds that a router's Hello packets have not been seen before it's neigh- bors declare the router down. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common network.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..65535

rcOspfv3IfPollInterval		1.3.6.1.4.1.2272.1.67.1.1.7.1.10
The larger time interval, in seconds, between the Hello packets sent to an inactive non- broadcast multi- access neighbor.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0..65535

rcOspfv3IfState		1.3.6.1.4.1.2272.1.67.1.1.7.1.11
The OSPFv3 Interface State.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	down(1), loopback(2), waiting(3), pointToPoint(4), designatedRouter(5), backupDesignatedRouter(6), otherDesignatedRouter(7)

rcOspfv3IfDesignatedRouter		1.3.6.1.4.1.2272.1.67.1.1.7.1.12
The Router ID of the Designated Router.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcOspfv3IfBackupDesignatedRouter		1.3.6.1.4.1.2272.1.67.1.1.7.1.14
The Router ID of the Backup Designated Router.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcOspfv3IfEvents		1.3.6.1.4.1.2272.1.67.1.1.7.1.15
The number of times this OSPF interface has changed its state, or an error has occurred.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcOspfv3IfStatus		1.3.6.1.4.1.2272.1.67.1.1.7.1.17
This variable controls the status of the en- try. The use of RowStatus is covered in more detail in [6].
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcOspfv3IfMulticastForwarding		1.3.6.1.4.1.2272.1.67.1.1.7.1.18
The way multicasts should forwarded on this interface; not forwarded, forwarded as data link multicasts, or forwarded as data link uni- casts. Data link multicasting is not meaning- ful on point to point and NBMA interfaces, and setting rcOspfv3MulticastForwarding to 0 effective- ly disables all multicast forwarding.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	blocked(1), multicast(2), unicast(3)

rcOspfv3IfDemand		1.3.6.1.4.1.2272.1.67.1.1.7.1.19
Indicates whether Demand OSPFv3 procedures (hel- lo suppression to FULL neighbors and setting the DoNotAge flag on propagated LSAs) should be per- formed on this interface.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcOspfv3IfMetricValue		1.3.6.1.4.1.2272.1.67.1.1.7.1.20
The metric assigned to this interface. The default value of the Metric is Reference Bandwidth / ifSpeed. The value of the reference bandwidth is configured by the rcOspfv3ReferenceBandwidth object. A value of '0' means the metric value of this interface will depend on the speed of the interface, when the state of the interface is up. The default (0) metric for Vlan and Tunnel is 10.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..FFFF

rcOspfv3IfLinkScopeLsaCount		1.3.6.1.4.1.2272.1.67.1.1.7.1.21
The total number of Link-Scope link-state advertisements in this link's link-state database.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcOspfv3IfLinkLsaCksumSum		1.3.6.1.4.1.2272.1.67.1.1.7.1.22
The 32-bit unsigned sum of the Link-Scope link-state advertisements' LS checksums contained in this link's link-state database. The sum can be used to determine if there has been a change in a router's link state database, and to compare the link-state database of two routers.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcOspfv3IfInstId		1.3.6.1.4.1.2272.1.67.1.1.7.1.23
Enables multiple instances of OSPFv3 to be run over a single link. Each protocol instance would be assigned a separate ID. This ID has local link significance only.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcOspfv3IfDemandNbrProbe		1.3.6.1.4.1.2272.1.67.1.1.7.1.24
Indicates whether or not neighbor probing is enabled to determine whether or not the neighbor is inactive. Neighbor probing is disabled by default.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcOspfv3IfDemandNbrProbeRetxLimit		1.3.6.1.4.1.2272.1.67.1.1.7.1.25
The number of consecutive LSA retransmissions before the neighbor is deemed inactive and the neighbor adjacency is brought down.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

rcOspfv3IfDemandNbrProbeInterval		1.3.6.1.4.1.2272.1.67.1.1.7.1.26
Defines how often the neighbor will be probed.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

rcOspfv3VirtIfTable		1.3.6.1.4.1.2272.1.67.1.1.8
Information about this router's virtual inter- faces.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcOspfv3VirtIfEntry

rcOspfv3VirtIfEntry		1.3.6.1.4.1.2272.1.67.1.1.8.1
Information about a single Virtual Interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcOspfv3VirtIfEntry

rcOspfv3VirtIfAreaId		1.3.6.1.4.1.2272.1.67.1.1.8.1.1
The Transit Area that the Virtual Link traverses. By definition, this is not 0.0.0.0
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rcOspfv3VirtIfNeighbor		1.3.6.1.4.1.2272.1.67.1.1.8.1.2
The Router ID of the Virtual Neighbor.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rcOspfv3VirtIfIndex		1.3.6.1.4.1.2272.1.67.1.1.8.1.3
The interface ID assigned to this OSPFv3 virtual interface. It is advertised in Hello's sent over the virtal link and in the router's router-LSAs.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcOspfv3VirtIfTransitDelay		1.3.6.1.4.1.2272.1.67.1.1.8.1.4
The estimated number of seconds it takes to transmit a link- state update packet over this interface.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..1800

rcOspfv3VirtIfRetransInterval		1.3.6.1.4.1.2272.1.67.1.1.8.1.5
The number of seconds between link-state ad- vertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database descrip- tion and link-state request packets. This value should be well over the expected round- trip time.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..1800

rcOspfv3VirtIfHelloInterval		1.3.6.1.4.1.2272.1.67.1.1.8.1.6
The length of time, in seconds, between the Hello packets that the router sends on the in- terface. This value must be the same for the virtual neighbor.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..FFFF

rcOspfv3VirtIfRtrDeadInterval		1.3.6.1.4.1.2272.1.67.1.1.8.1.7
The number of seconds that a router's Hello packets have not been seen before it's neigh- bors declare the router down. This should be some multiple of the Hello interval. This value must be the same for the virtual neigh- bor.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..65535

rcOspfv3VirtIfState		1.3.6.1.4.1.2272.1.67.1.1.8.1.8
OSPF virtual interface states.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	down(1), pointToPoint(4)

rcOspfv3VirtIfEvents		1.3.6.1.4.1.2272.1.67.1.1.8.1.9
The number of state changes or error events on this Virtual Link
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcOspfv3VirtIfStatus		1.3.6.1.4.1.2272.1.67.1.1.8.1.10
This variable controls the status of the en- try. The use of RowStatus is covered in more detail in [6].
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcOspfv3VirtIfLinkScopeLsaCount		1.3.6.1.4.1.2272.1.67.1.1.8.1.11
The total number of Link-Scope link-state advertisements in this virtual link's link-state database.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcOspfv3VirtIfLinkLsaCksumSum		1.3.6.1.4.1.2272.1.67.1.1.8.1.12
The 32-bit unsigned sum of the Link-Scope link-state advertisements' LS checksums contained in this virtual link's link-state database. The sum can be used to determine if there has been a change in a router's link state database, and to compare the link-state database of two routers.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcOspfv3NbrTable		1.3.6.1.4.1.2272.1.67.1.1.9
A table of non-virtual neighbor information.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcOspfv3NbrEntry

rcOspfv3NbrEntry		1.3.6.1.4.1.2272.1.67.1.1.9.1
The information regarding a single neighbor.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcOspfv3NbrEntry

rcOspfv3NbrIfIndex		1.3.6.1.4.1.2272.1.67.1.1.9.1.1
The local link ID of the link over which the neighbor can be reached.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

rcOspfv3NbrRtrId		1.3.6.1.4.1.2272.1.67.1.1.9.1.2
A 32-bit integer (represented as a type IpAd- dress) uniquely identifying the neighboring router in the Autonomous System.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rcOspfv3NbrAddressType		1.3.6.1.4.1.2272.1.67.1.1.9.1.3
The address type of rcOspfv3NbrAddress. Only IPv6 addresses without zone index are expected.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(0), ipv4(1), ipv6(2), ipv4z(3), ipv6z(4), dns(16)

rcOspfv3NbrAddress		1.3.6.1.4.1.2272.1.67.1.1.9.1.4
The IPv6 address of the neighbor associated with the local link.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(16)

rcOspfv3NbrOptions		1.3.6.1.4.1.2272.1.67.1.1.9.1.5
A Bit Mask corresponding to the neighbor's op- tions field.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcOspfv3NbrPriority		1.3.6.1.4.1.2272.1.67.1.1.9.1.6
The priority of this neighbor in the designat- ed router election algorithm. The value 0 sig- nifies that the neighbor is not eligible to be- come the designated router on this particular network.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..FF

rcOspfv3NbrState		1.3.6.1.4.1.2272.1.67.1.1.9.1.7
The State of the relationship with this Neigh- bor.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	down(1), attempt(2), init(3), twoWay(4), exchangeStart(5), exchange(6), loading(7), full(8)

rcOspfv3NbrEvents		1.3.6.1.4.1.2272.1.67.1.1.9.1.8
The number of times this neighbor relationship has changed state, or an error has occurred.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcOspfv3NbrLsRetransQLen		1.3.6.1.4.1.2272.1.67.1.1.9.1.9
The current length of the retransmission queue.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcOspfv3NbrHelloSuppressed		1.3.6.1.4.1.2272.1.67.1.1.9.1.10
Indicates whether Hellos are being suppressed to the neighbor
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcOspfv3NbrIfId		1.3.6.1.4.1.2272.1.67.1.1.9.1.11
The interface ID that the neighbor advertises in its Hello Packets on this link, that is, the neighbor's local interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcOspfv3NbrRestartHelperStatus		1.3.6.1.4.1.2272.1.67.1.1.9.1.12
Indicates whether the router is acting as a hitless restart helper for the neighbor.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notHelping(1), helping(2)

rcOspfv3NbrRestartHelperAge		1.3.6.1.4.1.2272.1.67.1.1.9.1.13
Remaining time in current OSPF hitless restart interval, if the router is acting as a restart helper for the neighbor.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..1800

rcOspfv3NbrRestartHelperExitReason		1.3.6.1.4.1.2272.1.67.1.1.9.1.14
Describes the outcome of the last attempt at acting as a hitless restart helper for the neighbor.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), inProgress(2), completed(3), timedOut(4), topologyChanged(5)

rcOspfv3NbmaNbrTable		1.3.6.1.4.1.2272.1.67.1.1.10
A table of configured non-virtual neighbor information and neighbors dynamically discovered by lower-level protocols such as Inverse Neighbor Discovery.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcOspfv3NbmaNbrEntry

rcOspfv3NbmaNbrEntry		1.3.6.1.4.1.2272.1.67.1.1.10.1
The information regarding a single configured neighbor or neighbor discovered by lower-level protocols such as Inverse Neighbor Discovery.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcOspfv3NbmaNbrEntry

rcOspfv3NbmaNbrIfIndex		1.3.6.1.4.1.2272.1.67.1.1.10.1.1
The local link ID of the link over which the neighbor can be reached.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

rcOspfv3NbmaNbrAddress		1.3.6.1.4.1.2272.1.67.1.1.10.1.2
The IPv6 address of the neighbor associated with the local link.
Status: current	Access: not-accessible
OBJECT-TYPE
	Ipv6Address

rcOspfv3NbmaNbrPriority		1.3.6.1.4.1.2272.1.67.1.1.10.1.3
The priority of this neighbor in the designat- ed router election algorithm. The value 0 sig- nifies that the neighbor is not eligible to be- come the designated router on this particular network.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..FF

rcOspfv3NbmaNbrRtrId		1.3.6.1.4.1.2272.1.67.1.1.10.1.4
A 32-bit integer (represented as a type IpAd- dress) uniquely identifying the neighboring router in the Autonomous System. A value of 0.0.0.0 is returned until a Hello is received from the configured neighbor.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcOspfv3NbmaNbrState		1.3.6.1.4.1.2272.1.67.1.1.10.1.5
The State of the relationship with this Neigh- bor.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	down(1), attempt(2), init(3), twoWay(4), exchangeStart(5), exchange(6), loading(7), full(8)

rcOspfv3NbmaNbrStorageType		1.3.6.1.4.1.2272.1.67.1.1.10.1.6
The storage type for this conceptual row. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row. Manually configured entries will have a storage type of nonVolatile while entries dynamically created as a result of a lower-level protocol such as Inverse Neighbor Discovery will have a storage type of volatile.
Status: current	Access: read-write
OBJECT-TYPE
	StorageType

rcOspfv3NbmaNbrStatus		1.3.6.1.4.1.2272.1.67.1.1.10.1.7
This variable controls the status of the en- try. The use of RowStatus is covered in more detail in [6].
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcOspfv3VirtNbrTable		1.3.6.1.4.1.2272.1.67.1.1.11
A table of virtual neighbor information.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcOspfv3VirtNbrEntry

rcOspfv3VirtNbrEntry		1.3.6.1.4.1.2272.1.67.1.1.11.1
Virtual neighbor information.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcOspfv3VirtNbrEntry

rcOspfv3VirtNbrArea		1.3.6.1.4.1.2272.1.67.1.1.11.1.1
The Transit Area Identifier.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rcOspfv3VirtNbrRtrId		1.3.6.1.4.1.2272.1.67.1.1.11.1.2
A 32-bit integer uniquely identifying the neighboring router in the Autonomous System.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rcOspfv3VirtNbrIfIndex		1.3.6.1.4.1.2272.1.67.1.1.11.1.3
The local interface ID for the virtual link over which the neighbor can be reached.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcOspfv3VirtNbrAddressType		1.3.6.1.4.1.2272.1.67.1.1.11.1.4
The address type of rcOspfv3VirtNbrAddress. Only IPv6 addresses without zone index are expected.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(0), ipv4(1), ipv6(2), ipv4z(3), ipv6z(4), dns(16)

rcOspfv3VirtNbrAddress		1.3.6.1.4.1.2272.1.67.1.1.11.1.5
The IPv6 address advertised by this Virtual Neighbor. It must be a Site-Local or Global scope address.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(16)

rcOspfv3VirtNbrOptions		1.3.6.1.4.1.2272.1.67.1.1.11.1.6
A Bit Mask corresponding to the neighbor's op- tions field.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcOspfv3VirtNbrState		1.3.6.1.4.1.2272.1.67.1.1.11.1.7
The state of the Virtual Neighbor Relation- ship.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	down(1), attempt(2), init(3), twoWay(4), exchangeStart(5), exchange(6), loading(7), full(8)

rcOspfv3VirtNbrEvents		1.3.6.1.4.1.2272.1.67.1.1.11.1.8
The number of times this virtual link has changed its state, or an error has occurred.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcOspfv3VirtNbrLsRetransQLen		1.3.6.1.4.1.2272.1.67.1.1.11.1.9
The current length of the retransmission queue.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcOspfv3VirtNbrHelloSuppressed		1.3.6.1.4.1.2272.1.67.1.1.11.1.10
Indicates whether Hellos are being suppressed to the neighbor
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcOspfv3VirtNbrIfId		1.3.6.1.4.1.2272.1.67.1.1.11.1.11
The interface ID that the neighbor advertises in its Hello Packets on this virtual link, that is, the neighbor's local interface ID.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcOspfv3VirtNbrRestartHelperStatus		1.3.6.1.4.1.2272.1.67.1.1.11.1.12
Indicates whether the router is acting as a hitless restart helper for the neighbor.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notHelping(1), helping(2)

rcOspfv3VirtNbrRestartHelperAge		1.3.6.1.4.1.2272.1.67.1.1.11.1.13
Remaining time in current OSPF hitless restart interval, if the router is acting as a restart helper for the neighbor.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..1800

rcOspfv3VirtNbrRestartHelperExitReason		1.3.6.1.4.1.2272.1.67.1.1.11.1.14
Describes the outcome of the last attempt at acting as a hitless restart helper for the neighbor.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), inProgress(2), completed(3), timedOut(4), topologyChanged(5)

rcOspfv3AreaAggregateTable		1.3.6.1.4.1.2272.1.67.1.1.12
A range of IPv6 prefixes specified by a prefix/prefix length pair. Note that if ranges are configured such that one range sub- sumes another range the most specific match is the preferred one.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcOspfv3AreaAggregateEntry

rcOspfv3AreaAggregateEntry		1.3.6.1.4.1.2272.1.67.1.1.12.1
A range of IPv6 prefixes specified by a prefix/prefix length pair. Note that if ranges are configured such that one range sub- sumes another range the most specific match is the preferred one.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcOspfv3AreaAggregateEntry

rcOspfv3AreaAggregateAreaID		1.3.6.1.4.1.2272.1.67.1.1.12.1.1
The Area the Address Aggregate is to be found within.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rcOspfv3AreaAggregateAreaLsdbType		1.3.6.1.4.1.2272.1.67.1.1.12.1.2
The type of the Address Aggregate. This field specifies the Area Lsdb type that this Address Ag- gregate applies to.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	interAreaPrefixLsa(8195), nssaExternalLsa(8199)

rcOspfv3AreaAggregatePrefix		1.3.6.1.4.1.2272.1.67.1.1.12.1.3
The IPv6 Prefix.
Status: current	Access: not-accessible
OBJECT-TYPE
	Ipv6Address

rcOspfv3AreaAggregatePrefixLength		1.3.6.1.4.1.2272.1.67.1.1.12.1.4
The length of the prefix (in bits). A prefix can not be shorter than 3 bits.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	3..128

rcOspfv3AreaAggregateStatus		1.3.6.1.4.1.2272.1.67.1.1.12.1.5
This variable controls the status of the en- try. The use of RowStatus is covered in more detail in [6].
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcOspfv3AreaAggregateEffect		1.3.6.1.4.1.2272.1.67.1.1.12.1.6
Prefixes subsumed by ranges either trigger the advertisement of the indicated aggregate (ad- vertiseMatching), or result in the prefix not being advertised at all outside the area.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	advertiseMatching(1), doNotAdvertiseMatching(2)

rcOspfv3AreaAggregateRouteTag		1.3.6.1.4.1.2272.1.67.1.1.12.1.7
This tag is advertised only in the summarized As-External LSA when summarizing from type-7 to type-5.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcOspfv3AreaAggregateAdvertiseMetric		1.3.6.1.4.1.2272.1.67.1.1.12.1.8
Used to specify a metric for a Summary LSA (type 3) generated by OSPF through an area range. If this metric is set to 0, OSPF uses the cost to the farthest point in the networks being summarized as the metric.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

rcOspfv3Stats		1.3.6.1.4.1.2272.1.67.1.1.13
OBJECT IDENTIFIER

rcOspfv3StatsTxPackets		1.3.6.1.4.1.2272.1.67.1.1.13.1
Used to indicate the number of packets transmitted by OSPF.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcOspfv3StatsRxPackets		1.3.6.1.4.1.2272.1.67.1.1.13.2
Used to indicate the number of packets received by OSPF.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcOspfv3StatsTxDropPackets		1.3.6.1.4.1.2272.1.67.1.1.13.3
Used to indicate the number of packets dropped before transmitted by OSPF.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcOspfv3StatsRxDropPackets		1.3.6.1.4.1.2272.1.67.1.1.13.4
Used to indicate the number of packets dropped before received by OSPF.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcOspfv3StatsRxBadPackets		1.3.6.1.4.1.2272.1.67.1.1.13.5
Used to indicate the number of packets received by OSPF that are bad.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcOspfv3StatsSpfRuns		1.3.6.1.4.1.2272.1.67.1.1.13.6
Used to indicate the total number of SPF calculations performed by OSPF, which also includes the number of partial route table calculation for Incremental Updates.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcOspfv3StatsLastSpfRun		1.3.6.1.4.1.2272.1.67.1.1.13.7
Used to indicate the time(SysUpTime) since the last spf calculated by OSPF.
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

rcOspfv3StatsLsdbTblSize		1.3.6.1.4.1.2272.1.67.1.1.13.8
Used to indicate the number of entries in the linkstate database table.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcOspfv3StatsBadLsReqs		1.3.6.1.4.1.2272.1.67.1.1.13.9
Used to indicate the number of bad ls requests.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcOspfv3StatsSeqMismatches		1.3.6.1.4.1.2272.1.67.1.1.13.10
Used to indicate the number of sequence mismatched packets.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcOspfv3Groups		1.3.6.1.4.1.2272.1.67.1.2.1
OBJECT IDENTIFIER

rcOspfv3Compliances		1.3.6.1.4.1.2272.1.67.1.2.2
OBJECT IDENTIFIER

rcOspfv3Compliance		1.3.6.1.4.1.2272.1.67.1.2.2.1
The compliance statement
Status: current	Access: read-only
MODULE-COMPLIANCE

rcOspfv3BasicGroup		1.3.6.1.4.1.2272.1.67.1.2.1.1
These objects are required for OSPFv3 systems.
Status: current	Access: read-only
OBJECT-GROUP

rcOspfv3AreaGroup		1.3.6.1.4.1.2272.1.67.1.2.1.2
These objects are required for OSPFv3 systems supporting areas.
Status: current	Access: read-only
OBJECT-GROUP

rcOspfv3AsLsdbGroup		1.3.6.1.4.1.2272.1.67.1.2.1.3
These objects are required for OSPFv3 systems that display their AS-scope link state database.
Status: current	Access: read-only
OBJECT-GROUP

rcOspfv3AreaLsdbGroup		1.3.6.1.4.1.2272.1.67.1.2.1.4
These objects are required for OSPFv3 systems that display their Area-scope link state database.
Status: current	Access: read-only
OBJECT-GROUP

rcOspfv3LinkLsdbGroup		1.3.6.1.4.1.2272.1.67.1.2.1.5
These objects are required for OSPFv3 systems that display their Link-scope link state database.
Status: current	Access: read-only
OBJECT-GROUP

rcOspfv3HostGroup		1.3.6.1.4.1.2272.1.67.1.2.1.6
These objects are required for OSPFv3 systems that support attached hosts.
Status: current	Access: read-only
OBJECT-GROUP

rcOspfv3IfGroup		1.3.6.1.4.1.2272.1.67.1.2.1.7
These interface objects are required for OSPFv3 systems.
Status: current	Access: read-only
OBJECT-GROUP

rcOspfv3VirtIfGroup		1.3.6.1.4.1.2272.1.67.1.2.1.8
These virtual interface objects are required for OSPFv3 systems.
Status: current	Access: read-only
OBJECT-GROUP

rcOspfv3NbrGroup		1.3.6.1.4.1.2272.1.67.1.2.1.9
These neighbor objects are required for OSPFv3 systems.
Status: current	Access: read-only
OBJECT-GROUP

rcOspfv3NbmaNbrGroup		1.3.6.1.4.1.2272.1.67.1.2.1.10
These NBMA neighbor objects are required for OSPFv3 systems.
Status: current	Access: read-only
OBJECT-GROUP

rcOspfv3VirtNbrGroup		1.3.6.1.4.1.2272.1.67.1.2.1.11
These virtual neighbor objects are required for OSPFv3 systems.
Status: current	Access: read-only
OBJECT-GROUP

rcOspfv3AreaAggregateGroup		1.3.6.1.4.1.2272.1.67.1.2.1.12
These area aggregate objects are required for OSPFv3 systems.
Status: current	Access: read-only
OBJECT-GROUP

rcIpv6ConfDhcpRelayTable		1.3.6.1.4.1.2272.1.62.1.1.9
DHCP Relay for Ipv6 configuration table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpv6ConfDhcpRelayEntry

rcIpv6ConfDhcpRelayEntry		1.3.6.1.4.1.2272.1.62.1.1.9.1
Used to configure DHCP on a particular L3 interface. An entry is created automatically when the variable rcIpv6InterfaceDhcpEnabled is set to TRUE. Once created this entry will only be deleted if the rcIpv6ConfDhcpRowStatus is set to 'destroy(6)'. In which case, the rcIpv6InterfaceDhcpEnabled is automatically reset to the FALSE setting.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpv6ConfDhcpRelayEntry

rcIpv6ConfDhcpIfIndex		1.3.6.1.4.1.2272.1.62.1.1.9.1.1
Interface number. The number can represent either a physical or logical(VLAN) interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex	1..6142

rcIpv6ConfDhcpMaxHop		1.3.6.1.4.1.2272.1.62.1.1.9.1.2
Used to indicate the maximum number of hops a DHCP packet can take from the source device to the destination device (i.e., DHCP client to DHCP server).
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	1..32

rcIpv6ConfDhcpRemoteIdEnabled		1.3.6.1.4.1.2272.1.62.1.1.9.1.3
Used to indicate if remote-id option is enabled.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcIpv6ConfDhcpNumRequests		1.3.6.1.4.1.2272.1.62.1.1.9.1.4
The total number of DHCP requests seen on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcIpv6ConfDhcpNumReplies		1.3.6.1.4.1.2272.1.62.1.1.9.1.5
The total number of DHCP replies seen on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcIpv6ConfDhcpRowStatus		1.3.6.1.4.1.2272.1.62.1.1.9.1.6
An entry is created automatically when the variable rcIpv6InterfaceDhcpEnabled is set to TRUE. Once created this entry will only be deleted if the rcIpv6ConfDhcpRowStatus is set to 'destroy(6)'. In which case, the rcIpv6InterfaceDhcpEnabled is automatically reset to the FALSE setting.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcIpv6DhcpForwardTable		1.3.6.1.4.1.2272.1.62.1.1.10
DHCP Relay forwarding table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpv6DhcpForwardEntry

rcIpv6DhcpForwardEntry		1.3.6.1.4.1.2272.1.62.1.1.10.1
An entry used represents a DHCP Relayed message forwarding directive.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpv6DhcpForwardEntry

rcIpv6DhcpForwardAgentAddr		1.3.6.1.4.1.2272.1.62.1.1.10.1.1
The IP address configured on an interface (i.e., a locally configured IP address).
Status: current	Access: not-accessible
OBJECT-TYPE
	Ipv6Address

rcIpv6DhcpForwardServerAddr		1.3.6.1.4.1.2272.1.62.1.1.10.1.2
The IP address of the DHCP server. If this IP address corresponds to a local interface address, the DHCP packet is multicast out the interface the IP address is assigned to.otherwise,the DHCP packet is sent via unicast to the remote device.
Status: current	Access: not-accessible
OBJECT-TYPE
	Ipv6Address

rcIpv6DhcpForwardEnabled		1.3.6.1.4.1.2272.1.62.1.1.10.1.3
Used to indicate whether the entry should be used.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcIpv6DhcpForwardRowStatus		1.3.6.1.4.1.2272.1.62.1.1.10.1.4
Row status of this entry.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcIpv6RadiusServTable		1.3.6.1.4.1.2272.1.62.1.1.11
The RADIUS table (0 to 10 entries). This table lists the information of the RADIUS server.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpv6RadiusServEntry

rcIpv6RadiusServEntry		1.3.6.1.4.1.2272.1.62.1.1.11.1
A RADIUS server table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpv6RadiusServEntry

rcIpv6RadiusServAddress		1.3.6.1.4.1.2272.1.62.1.1.11.1.1
Server IP address of the RADIUS authentication server referred to in this table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	Ipv6Address

rcIpv6RadiusServUsedBy		1.3.6.1.4.1.2272.1.62.1.1.11.1.2
cli(1): for cli login, igap(2): for igap,snmp(3): for snmp login, eap(4) for EAP PAE Authenticator,web(5) for EDM.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	cli(1), igap(2), snmp(3), eap(4), web(5)

rcIpv6RadiusServPriority		1.3.6.1.4.1.2272.1.62.1.1.11.1.3
Server priority, used to control which server to choose first to send authentication.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	1..10

rcIpv6RadiusServTimeOut		1.3.6.1.4.1.2272.1.62.1.1.11.1.4
The time interval in seconds before the client retransmit the packet.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	1..20

rcIpv6RadiusServEnable		1.3.6.1.4.1.2272.1.62.1.1.11.1.5
Enable or disable this server.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcIpv6RadiusServMaxRetries		1.3.6.1.4.1.2272.1.62.1.1.11.1.6
Maximum number of retransmissions.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..6

rcIpv6RadiusServUdpPort		1.3.6.1.4.1.2272.1.62.1.1.11.1.7
The UDP port the client is using to send requests to this server.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	1..65536

rcIpv6RadiusServSecretKey		1.3.6.1.4.1.2272.1.62.1.1.11.1.8
The identifier of the RADIUS authentication client.
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString	Size(0..32)

rcIpv6RadiusServAccessRequests		1.3.6.1.4.1.2272.1.62.1.1.11.1.9
The number of RADIUS access-response packets sent to this server. This does not include retransmissions.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcIpv6RadiusServAccessAccepts		1.3.6.1.4.1.2272.1.62.1.1.11.1.10
The number of RADIUS access-accept packets (valid or invalid) received from this server.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcIpv6RadiusServAccessRejects		1.3.6.1.4.1.2272.1.62.1.1.11.1.11
The number of RADIUS access-reject packets (valid or invalid) received from this server.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcIpv6RadiusServBadResponses		1.3.6.1.4.1.2272.1.62.1.1.11.1.12
The number of RADIUS invalid access-response packets received from this server.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcIpv6RadiusServPendingRequests		1.3.6.1.4.1.2272.1.62.1.1.11.1.13
The number of RADIUS access-request packets destined for this server that have not yet timed out or received a response. This variable is incremented when an access-request is sent and decremented due to receipt of an access-accept, access-reject, a timeout or retransmission.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcIpv6RadiusServClientRetries		1.3.6.1.4.1.2272.1.62.1.1.11.1.14
The number of authentication retransmission to this server.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcIpv6RadiusServAcctEnable		1.3.6.1.4.1.2272.1.62.1.1.11.1.15
Enable or disable Radius Accounting on this server.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcIpv6RadiusServAcctUdpPort		1.3.6.1.4.1.2272.1.62.1.1.11.1.16
The UDP port the client used to send accounting requests to this server.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	1..65536

rcIpv6RadiusServAcctOnRequests		1.3.6.1.4.1.2272.1.62.1.1.11.1.17
The number of RADIUS accounting-on packets sent to this server. This does not include retransmissions.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcIpv6RadiusServAcctOffRequests		1.3.6.1.4.1.2272.1.62.1.1.11.1.18
The number of RADIUS accounting-off packets sent to this server. This does not include retransmissions.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcIpv6RadiusServAcctStartRequests		1.3.6.1.4.1.2272.1.62.1.1.11.1.19
The number of RADIUS accounting-start packets sent to this server. This does not include retransmissions.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcIpv6RadiusServAcctStopRequests		1.3.6.1.4.1.2272.1.62.1.1.11.1.20
The number of RADIUS accounting-stop packets sent to this server. This does not include retransmissions.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcIpv6RadiusServAcctInterimRequests		1.3.6.1.4.1.2272.1.62.1.1.11.1.21
The number of RADIUS accounting-interim packets sent to this server. This does not include retransmissions.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcIpv6RadiusServAcctBadResponses		1.3.6.1.4.1.2272.1.62.1.1.11.1.22
The number of Invalid responses received from this server.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcIpv6RadiusServAcctPendingRequests		1.3.6.1.4.1.2272.1.62.1.1.11.1.23
The number of RADIUS accounting packets that are waiting be sent to this server. This variable is incremented whenever any accounting-request is sent to this server and decremented when an acknowledgement is received or timeout occurs.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcIpv6RadiusServAcctClientRetries		1.3.6.1.4.1.2272.1.62.1.1.11.1.24
The number of RADIUS accounting packets retransmitted to this server.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcIpv6RadiusServNasIpAddress		1.3.6.1.4.1.2272.1.62.1.1.11.1.25
RADIUS Client NAS Identifier for this server.
Status: current	Access: read-only
OBJECT-TYPE
	Ipv6Address

rcIpv6RadiusServRoundTripTime		1.3.6.1.4.1.2272.1.62.1.1.11.1.26
Time different between the instance when a RADIUS request is sent and the corresponding response is received.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString	Size(0..20)

rcIpv6RadiusServAccessChallanges		1.3.6.1.4.1.2272.1.62.1.1.11.1.27
The number of RADIUS access-challanges packets sent to this server. This does not include retransmission.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcIpv6RadiusServSourceIpAddr		1.3.6.1.4.1.2272.1.62.1.1.11.1.28
source IP address RADIUS packets.
Status: current	Access: read-create
OBJECT-TYPE
	Ipv6Address

rcIpv6RadiusServRowStatus		1.3.6.1.4.1.2272.1.62.1.1.11.1.29
Used to create/delete entries.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcIpMRouteMIBObjects		1.3.6.1.4.1.2272.1.76.1
OBJECT IDENTIFIER

rcIpMRouteScalars		1.3.6.1.4.1.2272.1.76.1.1
OBJECT IDENTIFIER

rcIpMRouteStatsEnabled		1.3.6.1.4.1.2272.1.76.1.1.2
The enabled status of IP Multicast statistics.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpMRouteStatsClear		1.3.6.1.4.1.2272.1.76.1.1.3
Clear ip mroute stats.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpMRouteStatsTable		1.3.6.1.4.1.2272.1.76.1.6
the table containing IP Multicast statistics.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpMRouteStatsEntry

rcIpMRouteStatsEntry		1.3.6.1.4.1.2272.1.76.1.6.1
An entry containing the ip multicast statistics information for the specific group ip address.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpMRouteStatsEntry

rcIpMRouteStatsGroupAddress		1.3.6.1.4.1.2272.1.76.1.6.1.1
the IP multicast group address for which this entry contains ip multicast statistics.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rcIpMRouteStatsSourceCount		1.3.6.1.4.1.2272.1.76.1.6.1.2
The number of sources corresponding to the specific group and vrf.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcIpMRouteStatsPkts		1.3.6.1.4.1.2272.1.76.1.6.1.3
The total number of frames that are processed corresponding to the specific group and vrf.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcIpMRouteStatsBytes		1.3.6.1.4.1.2272.1.76.1.6.1.4
The total number of bytes that are processed corresponding to the specific group and vrf.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcIpMRouteStatsAverageSizePerPkt		1.3.6.1.4.1.2272.1.76.1.6.1.5
The average length of packets that are processed corresponding to the specific group and vrf.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpMRouteStatsDropPkts		1.3.6.1.4.1.2272.1.76.1.6.1.6
The total number of drop frames that are processed corresponding to the specific group and vrf.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcIpMRouteStatsDropBytes		1.3.6.1.4.1.2272.1.76.1.6.1.7
The total number of drop bytes that are processed corresponding to the specific group and vrf.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcIpMRouteStatsPktsPerSecond		1.3.6.1.4.1.2272.1.76.1.6.1.8
The number of packets that are processed corresponding to the specific group and vrf in one second.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcErrorReturnCode		1.3.6.1.4.1.2272.1.20.4
This variable is used primarily as an enumeration to list the proprietary return codes that this device can send to a management station in response to a failed SNMP operation.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(100), resourceNotAvailable(101), operationNotAllowed(102), operationInProgress(103), invalidPortNumber(104), invalidSubnetAddress(105), invalidSubnetMask(106), invalidVlanId(107), invalidVlanName(108), invalidVlanType(109), invalidStgId(110), invalidProtocolId(111), invalidPortMembers(112), invalidStaticMembers(113), invalidNotAllowedMembers(114), destinationNotReachable(115), tableIsFull(116), nondualConnectorGigPort(117), testIdNotPresent(118), invalidTestId(119), invalidStatusChange(120), invalidCpuCard(121), invalidSrcPortChoice(122), dstPortUnspecified(123), srcPortOneUnspecified(124), srcPortTwoUnspecified(125), notSupported(126), userNameIsNonUnique(127), invalidName(128), unknownErrorCode1(129), cannotModifyThisField(130), invalidUserPasswordLength(131), thisUsernameExists(132), invalidIpAddress(133), invalidMacAddress(134), nosuchEntry(135), anotherLoopBackTestAlreadyRunning(136), protocolIdNotRoutable(137), autoNegotiateIsOn(138), noActionSpecified(139), invalidActionSpecified(140), cannotModifyAutoNegotiateIsOn(141), cannotModifyAutoPortIsFiber(142), autoNegotiationNotSupported(143), cannotSetAdminSpeed(144), cannotSetAdminDuplex(145), ospfRtrDeadIntIsnotMultOfHelloInt(146), ospfRtrDeadIntLessThan4TimesHelloInt(147), notUsed1(148), ospfBadAuthValue(149), ospfEnabled(150), ospfAreaNotFound(151), ospfBackboneArea(152), notInTestMode(153), ospfInvalidAreaRangeMask(154), ospfDuplicateEntry(155), ospfRangeNotAllocated(156), ospfAreaRangeNotFound(157), testRunning(158), nvramLimitExceeded(159), flowAlreadyExist(160), flowNotFound(161), invalidOspfAreaRangeNet(162), duplicateIpAddress(163), conflictingIpAddress(164), invalidRouteCost(165), invalidNextHop(166), duplicateRoute(167), cannotFindRoute(168), cannotDeleteLocalRoute(169), badDhcpMinSec(170), badDhcpMaxHop(171), badDhcpMode(172), badAgentAddress(173), dhcpNotEnabled(174), dhcpForwardNotFound(175), dhcpDuplicateForward(176), dhcpMaxForward(177), dhcpBadEnable(178), invalidDeviceFileNumber(179), notExecutableDeviceFile(180), deletedDeviceFile(181), pcmciaNotPresent(182), pcmciaWriteProtected(183), discontiguousSubnetMask(184), invalidOspfMetric(185), ospfHostRouteNotFound(186), invalidMltId(187), invalidMltName(188), onlyOnePortInMlt(189), moreThan4PortsInMlt(190), portsInDifferentQuid(191), portAlreadyInAnotherMlt(192), invalidVlan(193), nonExistIpMcastAddriess(194), invalidIpMulticastAddress(195), portIsLocked(196), accessRestriction(197), invalidDeviceFileLength(198), duplicateAccessPolicyId(199), noDesiredAccessPolicyItem(200), ipfFilterNonExist(201), ipfInvalidVlanPriority(202), ipfInvalidDestinationAddress(203), ipfInvalidSourceAddress(204), ipfFilterDuplicate(205), ipfGlobalListDuplicate(206), ipfGlobalListNonExist(207), ipfBaseListDuplicate(208), ipfBaseListNonExist(209), ipfPortDuplicate(210), ipfPortNonExist(211), ipfListNonExist(212), snmpSnoopDisabled(213), invalidHostIpAddress(214), snoopStaticGroupExist(215), ripAnnouncePolicyNotFound(216), duplicateRipAnnouncePolicy(217), ospfAnnouncePolicyNotFound(218), duplicateOspfAnnouncePolicy(219), policyMatchNetEntryNotFound(220), duplicatePolicyNetEntry(221), policyAddrListEntryNotFound(222), duplicatePolicyAddrListEntry(223), policyAddrListIdNotFound(224), policyExactNetListNotFound(225), policyRangeNetListNotFound(226), policyRipGatewayListNotFound(227), policyRipInterfaceListNotFound(228), policyOspfRtrIdListNotFound(229), policyAnnounceInterfaceListNotFound(230), policyAdvertiseNetListNotFound(231), policyInjectNetListNotFound(232), invalidPolicyListIdListSize(233), policyAddrEntryNotFound(234), duplicatePolicyAddrEntry(235), disableThisPortFirst(236), mutinettingNotSupported(237), addingGlobalFilterToNonGlobalList(238), addingNonGlobalFilterToGlobalList(239), setFilteredPortMode(240), setFilteredPortEnableValue(241), invalidModeType(242), duplicateRipAcceptPolicy(243), ripAccepPolicyNotFound(244), duplicateOspfAcceptPolicy(245), ospfAccepPolicyNotFound(246), invalidAccessPolicyName(247), invalidAccessPolicyPolicyEnable(248), invalidAccessPolicyMode(249), invalidAccessPolicyService(250), invalidAccessPolicyPrecedence(251), invalidAccessPolicyNetAddress(252), invalidAccessPolicyTrustedHostAddress(253), invalidAccessPolicyTrustedHostUserName(254), invalidAccessPolicyAccessLevel(255), invalidAccessPolicyLogSetting(256), invalidAccessPolicyPolicyId(257), invalidAreaOptions(258), cannotDeleteAreaIfCountIsNotZero(259), ospfInterfaceNotFound(260), ospfIfAreaIdConflictsWithConfiguredAreaRange(261), applyingDuplicateGlobalFilterToPort(262), differentMltPortTypes(263), addPortToMltFailed(264), removePortFromMltFailed(265), mirrorPortInMlt(266), invalidDhcpAlwaysBroadcast(267), interfaceIsSetToTransmitRipV1(268), ripInterfaceDoesnotExist(269), interfaceIsNotRunningRip(270), cannotCreateVirtLinksThroughStubArea(271), invalidSyslogEnableSetting(272), invalidSyslogMaxHostsSettings(273), invalidSyslogHostIpAddr(274), invalidSyslogHostUdpPort(275), invalidSyslogHostFacility(276), invalidSyslogModuleId(277), invalidSyslogSeverity(278), invalidSyslogMapInfoSeverity(279), invalidSyslogMapWarningSeverity(280), invalidSyslogMapErrorSeverity(281), invalidSyslogMapMfgSeverity(282), invalidSyslogMapFatalSeverity(283), invalidSyslogMapTraceMsgSetting(284), invalidSyslogMapTrapMsgSetting(285), invalidSyslogLogTraceMsgSetting(286), invalidSyslogLogTrapMsgSetting(287), invalidSyslogEntryEnableSetting(288), invalidSyslogMaxHostSetting(289), invalidSyslogHostId(290), duplicateSyslogEntry(291), syslogHostTableIsFull(292), noDesiredSyslogHostEntryFound(293), invalidHoldDownTime(294), incompatibleAruHardware(295), invalidVrid(296), duplicateVrrpEntry(297), noVrrpIpAddressSpecified(298), invalidVrrpControlValue(299), invalidVrrpPriority(300), invalidVrrpAdvertisementInterval(301), maxNumOfVrrpsEntriesExceeded(302), policyNetListEntryNotFound(303), duplicatePolicyNetListEntry(304), policyNetListIdNotFound(305), filterOnAnEnabledPort(306), listOnAnEnabledPort(307), invalidIpFilterSrcOption(308), invalidIpFilterDstOption(309), invalidOspfAreaImportextOption(310), invalidOspfInterfaceMd5KeyIdLength(311), invalidOspfInterfaceMd5KeyLength(312), invalidIPXNetworkNumber(313), ipxCircuitAlreadyExists(314), ipxCircuitDoesNotExist(315), encapsulationIsNotAllowedOnSameSegment(316), encapsulationDoesNotMatchProtocolBasedVLAN(317), invalidDvmrpIfTblEnableValue(318), invalidDvmrpIfTblMetricValue(319), ipHostPartForSubnetAddrIsNonZero(320), globalMulticastNotEnabled(321), metricFieldIsCreatedButModified(322), invalidIpMRouteInterfaceTblTtlValue(323), invalidUdpPortNumber(324), invalidUdpProtocolNameLength(325), cannotModifyUdpProtocolName(326), udpProtocolEntryDoesnotexists(327), duplicateUdpProtocolEntry(328), cannotDelUdpProtocolEntryFwdEntriesExists(329), udpBroadcastIntfEntryDoesnotExists(330), duplicateUdpBroadcastIntfEntry(331), invalidUdpConfBroacastInterface(332), updConfIntfEntryNotEnabledForUdpBcastForwarding(333), udpPortFwdEntryDoesnotExists(334), duplicateUdpPortFwdEntryDoesnotExists(335), udpPortFwdEntryUdpPortInterfaceDoesnotExists(336), udpPortFwdListEntryDoesnotExists(337), duplicateUdpPortFwdListEntryDoesnotExists(338), udpPortFwdListEntryPortFwdIdDoesnotExists(339), udpPortFwdListEntryinvalidFwdIdListSize(340), cannotDeleteUdpPortFwdListEntryInterfaceUsingThisList(341), invalidIgmpSnoopDestAddress(342), invalidIgmpSnoopHostAddress(343), cannotDeleteDefaultUdpProtocolTblEntry(344), nextHopRouteIsStaticRoute(345), invalidUpdateIntervalValueInDVMRPGlobalTable(346), invalidTriggeredUpdateIntervalValueInDVMRPGlobalTable(347), invalidLeafTimeoutValueInDVMRPGlobalTable(348), invalidNbrTimeoutValueInDVMRPGlobalTable(349), invalidNbrProbeIntervalValueInDVMRPGlobalTable(350), invalidQueryIntervalValueInIgmpInterfaceTable(351), invalidVersionValueInIgmpInterfaceTable(352), invalidQueryMaxResponseTimeValueInIgmpInterfaceTable(353), invalidRobustnessValueInIgmpInterfaceTable(354), invalidLastMembQueryIntvlValueInIgmpInterfaceTable(355), invalidANDMaskInRcIpTosRuleGroup(356), invalidORRule1InRcIpTosRuleGroup(357), invalidORRule2InRcIpTosRuleGroup(358), invalidORRule3InRcIpTosRuleGroup(359), deleteStaticPortNotValid(360), maxEntriesForIgmpAccTbl(361), maxMaskNumberOfHostIgmpAccTbl(362), dvmrpIgmpExclusive(363), theSpecifiedAreaRangeMaskIsInvalid(364), invalidLengthOf2kBootConfigImageSource(365), invalidLengthOf2kBootConfigSource(366), preferenceOfStaticRouteIsInvalid(367), copyFileOutOfSpace(368), copyFileFileNotFound(369), copyFileInvalidDestination(370), copyFileInvalidSource(371), copyFileFail(372), invalidLinkFlapDetectAutoPortDown(373), invalidLinkFlapDetectFrequency(374), invalidLinkFlapDetectInterval(375), invalidLinkFlapDetectSendTrap(376), invalidQosLevel(377), invalidQosWeight(378), invalidQosThreshold(379), invalidTagToQosTableIeee1pValue(380), invalidTagToQosTableQosLevel(381), invalidDsFieldToQosTableDsField(382), invalidDsFieldToQosTableQosLevel(383), invalidQosToTagTableQosLevel(384), invalidQosToTagTableIeee1pValue(385), invalidQosLevelValue(386), invalidQosToDsFieldTableDsFieldValue(387), invalidQosToDsFieldTableQosLevel(388), invalidDiffServEnable(389), invalidDiffServType(390), invalidIeeeOverride(391), invalidVlanQosValue(392), invalidVlanTosValue(393), operationNotAllowedOnAccessPort(394), operationNotAllowedOnTaggingPort(395), invalidFileName(396), invalidDiaglogueDuplicateMirroredPort(397), invalidDiaglogueEnableValue(398), invalidDiaglogueEnableSetting(399), invalidDiaglogueModeSetting(400), invalidDiaglogueEntryId(401), srcMacVlanIsNotYetEnabled(402), srcMacVlanIsNotYetDisabled(403), invalidDiaglogueOperation(404), invalidMacAddressSpecied(405), maxResponseTimeGreaterThanQueryInterval(406), noModifyDsFltrAllowedOnDiffSrvCorePort(407), mltMoreThan4PortsInMgMlt(408), protocolRulesForThePortHasExceeded16(409), routeDoesNotExistsInTheRroutingTable(410), diagMirrorByPortTableAccessError(411), diagMirrorByPortInvalidMirroringPortSetting(412), igmpAdminVersionConfiguredLessThanOperatingVersion(413), canOnlyConfigureViaMltTable(414), dvmrpInterfaceTableIsFull(415), invalidDscpField(416), invalidDscpReservedField(417), disablePortPriorToChangingDiffServPortType(418), ipFilterInvalidId(419), rateLimitingExceeded(420), diagEntryMaxExceeded(421), onlyOneMirroringPortAllow(422), radiusServerExist(423), radiusServerNotExist(424), radiusServerInUse(425), radiusMaxServerNumExceeded(426), radiusInvalidAttribute(427), canNotChangeLocking(428), activationDisabled(429), zeroMac(430), atmBadVpi(431), atmBadVci(432), atmBadFramingMode(433), atmDestroyPvcFailed(434), atmBadName(435), atmBadEnable(436), atmBadpvcEncapsulation(437), atmBadPvdServiceType(438), atmBadPeakCellRate(439), atmBadSustainedCellRate(440), atmBadMaxBurstSize(441), atmBadMaxMtuSize(442), atmBadElanId(443), atmUnknownOperation(444), atmDestroy1483ElanFailed(445), atmBadPerformTagging(446), atmIlleagalElanDefinition(447), atmCreate1483ElanFailed(448), atmBadSnmpMessage(449), atmBadScrambleEnable(450), atmBadSignalingEnable(451), atmBadClockSource(452), atmBadLoopback(453), badRowStatus(454), atmBadLaneConfigMode(455), atmLecCreationFailed(456), atmBad1438Inarp(457), atmF5StartFailed(458), atmBadPvcId(459), atmBadConnectType(460), atmBadIpxEncapMethod(461), atmBadUniVersion(462), atmCreatePvcFailed(463), invalidLoginPromptLength(464), invalidPasswordPromptLength(465), invalidCliBannerLength(466), invalidCliBannerSize(467), invalidCliMotdLength(468), invalidCliMotdSize(469), invalidPortNameLength(470), invalidPortName(471), invalidMaxAdvertiseInterval(472), invalidMinAdvertiseInterval(473), invalidMaxInitialAdvertiseInterval(474), invalidMaxInitalAdvertments(475), invalidNeigborDeadInterval(476), invalidUserSetTimeYearValue(477), invalidUserSetTimeMonthValue(478), invalidUserSetTimeDateValue(479), invalidUserSetTimeHourValue(480), invalidUserSetTimeMinuteValue(481), invalidUserSetTimeSecondValue(482), rtcIsNotPresent(483), rtcIsNotRunning(484), maxMacCount(485), maxAdvertiseIntLessThanMinAdvertiseInt(486), minAdvertiseIntGreaterThanMaxAdvertiseInt(487), dvmrpNotEnabledGlobally(488), vrrpCriticalIpAddrNotEnable(489), vrrpInvalidCriticalIpAddr(490), metricConfigNotAllowed(491), posActiveNonBcpEnabledPort(492), posVlanNoMorePorts(493), posPortCanBeAdded(494), posNonBcpCanNotBeEnabled(495), posImageFilenameTooLong(496), posNoIpcpEnableOnMltPorts(497), posNoIpcpEnableOnTagPort(498), posNoIpxcpEnableOnMltPort(499), posNoIpxcpEnableOnTagPort(500), posDisableTagBeforeBcpDisable(501), posAssignIpBeforeIpcpEnable(502), posAssignIpxBeforeIpxcpEnable(503), posAssignIpBeforeRemoteIp(504), posKeepRemoteIpInSameSubnet(505), staticRouteEnabled(506), cannotChangeAutoLearnState(507), invalidVirtualIpAddr(508), virtualAndPhysicalIpNotInSameSubnet(509), vidNotAvailable(510), mgidNotAvailable(511), posNoIpcpEnableOnPolicyVlanPort(512), posNoIpxcpEnableOnPolicyVlanPort(513), posVrrpNotAllowed(514), webInvalidHttpPort(515), cannotAddMulticastStaticMac(516), posNoStpEnableWithBCPClosed(517), posAtmNoRip1(518), ipfFilterNumOverFilterSetLimit(519), ipfQosTrafficAverageRateOverLimit(520), ipfQosTrafficProfileNotExist(521), atmNoIpIpxConfigOnVlan(522), atmPvcIsInUse(523), globalFilterNotDisabled(524), dhcpNotOnByIpSubnetVlan(525), cannotConfigureDefaultGateway(526), routeExists(527), gatewayNotOnMgmtInterfaceSubnet(528), mgmtRouteTableFull(529), routeNotExists(530), invalidMacOffsetRangeForBW(531), invalidMacOffsetRangeForMG(532), atmPvcBadPeakCellRate(533), atmPvcBadSustainedCellRate(534), qosReservedQosLevel(535), dvmrpGlobInvalidFwdCacheTimeOut(536), dvmrpGlobInvalidRouteExpireTimeOut(537), dvmrpGlobInvalidRouteDiscardTimeOut(538), dvmrpGlobInvalidRouteSwitchTimeOut(539), pimCondRPGroupExists(540), pimCandRPAddressInvalid(541), pimGroupAddressInvalid(542), pimNotEnabled(543), pimInvalidJPInterval(544), pimInvalidMode(545), pimInvalidHelloInt(546), pimInvalidCBSRPRef(547), pimInvalidEnable(548), pimAlreadyEnabled(549), ipDvmrpAlreadyEnabled(550), ospfIntfChangeNotAllowedWhenEnabled(551), ospfIntfChangeFromNBMANotAllowed(552), ospfPollIntIsnotMultOfHelloInt(553), ospfNeigNoCircuit(554), ospfNeigSameIp(555), ospfCircNotNBMA(556), ospfCircPriZero(557), ospfNBMANeigExist(558), ospfNBMANeigNotFound(559), ospfDynNeigExist(560), pgmInvalidSessionLifetime(561), pgmInvalidMaxRetxStates(562), pgmInvalidMaxSessions(563), pgmInvalidIfNakRetxInterval(564), pgmInvalidIfMaxNakRetxCnt(565), pgmInvalidIfNakRdataInt(566), pgmInvalidIfNakElimInt(567), maxOfMirroringPortAllowedExceed(568), duplicatedRoutePolicyEntry(569), specifiedRoutePolicyEntryNotFound(570), specifiedPrefixListNotFound(571), routePolicyListNotSpecify(572), routePolicyPrefixListOverLimit(573), ipPrefixListDuplicate(574), ipPrefixListDuplicateEntry(575), ipPrefixListEntryNotFound(576), ipPrefixListInvalidName(577), ipRedistributeDuplicateEntry(578), ipRedistributeEntryNotFound(579), ipOspfInFilterDuplicateEntry(580), ipOspfInFilterEntryNotFound(581), ipEcmpNotDisabled(582), ipEcmpMaxExceeded(583), ipfQosTrafficAvgRateZeroProfileEnable(584), ipmTimePruneEntryInvalidGroup(585), ipmTimePruneEntryDuplicate(586), ipmTimePruneEntryNotExist(587), ipmTimePruneEntryInvalidExpireTime(588), smltIstExist(589), smltSmltIdExist(590), smltIstNotExist(591), smltSmltIsEnabled(592), smltSmltLocalIpNotExist(593), smltInvalidPortTypeForIstMlt(594), ntpServerAlreadyExist(595), ntpServerDoesNotExist(596), ntpKeyAlreadyExists(597), ntpKeyDoesNotExist(598), ntpMaxKeyExceeded(599), ntpServerAlreadyEnabled(600), ntpServerAlreadyDisabled(601), ntpNoServerConfigured(602), ntpMaxServerNumExceeded(603), ntpInvalidIntervalValue(604), ecmpNotEnabled(605), ipfInvalidProtocolType(606), assignIpToPortInRouteVlan(607), assignIpToVlanWithRoutePortMember(608), ipfIstPort(609), smltMltIpfExist(610), smltMltPortIpfExist(611), smltL2fIstPort(612), smltMltL2fExist(613), smltMltPortL2fExist(614), portMirroringEgressNotSupportFullDuplexMode(615), pimGlobInvalidRegSupprTimeOut(616), smltNotAvailableIn8100(617), mltNoPort(618), mltInvalidPortType(619), inUsedByATM1483Elan(620), smltIstStpEnableNotAllowed(621), invalidHighestVrrpPrio(622), dynamicPortMemberIn8100IsNotAllowed(623), ipfGlobalNextHopModeNotSupported(624), smltPeerIpNotExist(625), smltMltNoThisVlan(626), smltNotANormalMlt(627), validStaticRtExist(628), validBlkHolRtExist(629), pimOrIgmpAlreadyEnabled(630), communityAlreadyExists(9101), communityDoesnotExist(9102), communityStorageTypePermanent(9103), defaultEntryNotDeletable(9104), invalidAccessPolicyStrict(9105), targetAddressNotExist(9106), cannotChangeCurrentAndDeprecatedMib(9107), duplicateTargetAddress(9110), notifyTagIsOnlyAllowedUpTo32Chars(9112), portMirroringTxNotSupportForThisHardwareRevision(9301), cannotSetMode(9302), cannotSetFraming(9303), cannotModifyInLaneMode(9304), stpIsNotAllowedToBeEnabledOnIstPort(9305), mirroredPortSupportRXModeOnly(9306), secondaryCpuNotActive(9307), commandNotAllowedInPrimaryCpu(9308), pcapUserDefinedDataInConsistency(9309), pcapFilterTblEntryNotFound(9310), pcapFilterTblDuplicateEntry(9311), pcapBufferSizeExceedsMaximumRamLimit(9312), portPcapIsActive(9313), pcapCommandNotAllowedWhenPcapIsEnabled(9314), invalidNumberOfHexDigits(9315), commandNotAllowedInHaCpuMode(9316), pcapCommandNotAllowedIn3SlotChassis(9317), pcapNoMemoryAllocatedForPcap(9318), pcapCannotBeEnabledWhenAutosaveInProgress(9319), pcapInvalidTimerRangeValue(9320), cannotSetPortAdminRouting(9322), smltNotAllowedObBrouterPort(9323), pcapOctapidNotInitialized(9324), pcapNoPackets(9325), pcapInsufficientDiskSpace(9326), pcapAutoSaveOrCopyCommandInProgress(9327), rmCommandNotAllowedWhenRemoteMirroringIsEnabled(9328), rmVlanNotPortBasedVlan(9329), rmPortNotMemberOfVlan(9330), rmSrcMacAddressNotSet(9331), rmRemoteMirroringActiveInOctapd(9332), rmRmtExceedsMaxLimit(9333), rmVlanIdNotSetForRmtPort(9334), rmDstMacNotSet(9335), rmPortDuplicateEntry(9336), rmPortEntryNotCreated(9337), portMirroringTxNotSupportForDiffservPort(10335), invalidDiffServEnableDueToMirroring(10336), invalidDiffServTypeDueToMirroring(10337), rmRemoteMirroringActiveInRspLane(9382), portEapAuthorized(9345), portEapEnabled(9362), rateLimitingrmodPort(9363), bandwidthLimitingNonrmodPort(9364), egressRateLimitingNotAppToNonRModPort(9365), featureNotApplyToMixedMlt(9368), rateLimitingExistsForMlt(9369), differentPortConfigurationForMlt(9370), rModuleOnlyOneMirroredPortPerLane(9371), ieee8021pOverrideNotAppToNonRModPort(9372), portMirroringTxFilterNotSupportForThisHardwareRevision(9373), portIsDownOperationNotAllowed(9374), portSffdEnableError(9375), portTxFlowControlNotSupportedForThisHW(9376), portFcPause0NotSupportedForThisHW(9377), portFcPauseTimeNotSupportedForThisHW(9378), slppInvalidTxInterval(9380), slppInvalidRxThreshold(9381), cannotSetClockSource(9394), ingressPoliceNonRsPort(9395), customAutoNegAdvertNotSupported(9396), autoNegotiateIsDisable(9397), recordReserveTypeInvalid(9401), recordReserveOutOfRange(9402), recordReserveExceedPhyLim(9403), cannotUpNonEticketCard(9404), cannotUpNon128KCard(9405), naapVlanNotConfigured(9406), lpMiniSlotNotPresent(9407), lpSlotDisabled(9408), lpSlotEnabled(9409), cannotUpNonEmmodeCard(9410), cannotUpNonRmodeCard(9411), cannotUpNonRspCard(9412), dnsDuplicateEntry(9413), dnsEntryNotFound(9414), dnsEntryNotCreated(9415), smartCpldNotSupported(9416), slotNotPresent(9418), rmodeRequired(9419), maxVlanDisallow(9420), softwareLicenseViolation(9425), cpuActionNotAllowed(9426), resetOperNotAllowed(9427), cpuActionNotAllowedPwrPrio(9428), ntpIncorrectKeyValue(9435), accessPolicyGroupNameInvalid(9436), sysTakeIOCardOfflineMustBeEnabledFirst(9456), sysAutoResetFabricMustBeDisabledFirst(9457), tenGEMltPortCannotBeAddedToStgWithSMLT(9501), tenGEPortCannotBeAddedToStgWithSMLT(9502), rstpInvalidVal(9504), mstpInvalidVal(9505), priorityValueMustBeAMultipleOf4096(9510), maxAgeMustEqualOrGreatThan2XPortHelloTimePlus1Second(9520), maxAgeMustEqualOrLessThan2XForwardDelayMinus1Second(9529), pbtStgCannotEnableStp(9521), mappingExistsForInstanceUnmapVlansFirst(9535), plsbMstpInstanceAllowedOnlyInMstpMode(9536), plsbStgInstanceCannotBeRemovedWhenPlsbVlanExists(9537), stgInstanceCannotBeSetToPlsbType(9538), plsbMstiCannotEnableForcePortState(9539), protocolMigrationCannotBeSetIfForceportstateIsDisabled(9540), protocolMigrationCanBeSetOnlyForForceVersionRstpOrMstp(9541), ospfOverlappingSummarizedRange(9601), ospfHelloIntNotGreatDeadInt(9605), invalidOperation(9608), cluserInvalidId(9901), clusterDoesNotExist(9902), clusterAlreadyExists(9903), clusterSizeExceeded(9904), invalidMiniSlot(9905), brouterOpNotAllowedOnIsdPort(9907), clusterIdMandatory(9906), removeVlanBeforeDeletingCluster(9908), vlanWithIPXEnabledCannotAdd10GEPortOrMlt(1101), addRemDsapSsapNotAllowed(1102), maxDsapSsapExceeded(1103), vlanInvalidEncap(1104), vlanEnforcementNotAllowed(1109), vlanNaapVlanPortMustBeTagged(1110), vlanRegPortNotAllowedInNaapVlan(1111), vlanFwPortNotAllowedInRegVlan(1112), invalidVlanIdSpecified(1113), retrieve10GEInfoFailure(1115), minMacGreaterThanMaxMac(1116), maxMacLessThanMinMac(1117), prPortNotForStackedVlan(1121), prPortNotForIPXVlan(1122), vlanAgingTimeNotAppToStaticVlan(1123), naapInvalidVlanId(1126), clusterIsdAlreadyUsed(1129), regularPortsNotAllowedInPeeringVlan(1130), regularPortsNotAllowedInClusterSyncVlan(1131), mltSdmPortNotAllowed(1132), clusterIdNotAllowedForNormalVlan(1133), clusterTypeNotSupported(1134), clusterMgmtSyncVlanCannotBeSame(1135), nsnaPortNotConfigurable(1138), nsnaUplinkOperationNotAllowed(1139), clusterTpsSizeExceeded(1145), clusterNotFwIsd(1148), clusterNotTpsIsd(1149), vlanFwPortDelNotAllowedInRegVlan(1151), fwPortNotAlwdForClusterTypeIs(1152), syncVlanNotAlwdForClusterTypeIs(1153), portMemberNotAlwdForNonIsCluster(1154), portMemberOfIsClusterCannotBeSdmPort(1155), portHasPcapEnabled(1156), portInSameOctapidAsIsCluster(1157), pcapInvalidTypeForAclFilter(1160), rmodOnlyOnePcapPortPerLane(1161), fdbEntryNotFound(1172), fdbStatusMismatch(1173), rstpOnlyDefaultInstanceAllowed(1174), vlanMacRecordDoesNotExist(1182), vlanMacRecordIsNotALearnedMac(1183), vlanFdbMandatoryParametersMissing(1184), cannotCreateFilterEntryForTdpMac(1187), entryAlreadyExists(1188), macIsConfiguredAsStaticMacInVlan(1189), macHasBeenLearntConfiguredInVlan(1190), macIsBeingUsedAsLoopDetectMac(1191), cannotCreateFilterEntryForLocalMac(1192), cannotCreateFilterEntryForBpudMac(1193), cannotCreateFilterEntryForLacpMac(1194), cannotCreateFilterEntryForVlacpMac(1195), cannotAddPortsToPlsbBVlan(1198), dynModMaxModule(1201), dynModUnknown(1202), dynModAlreadyLoaded(1203), dynModCantOpenFile(1204), dynModNotEnoughSpace(1205), circuitlestInvalidIpInterfaceId(1501), circuitlessMaxNumberIpInterfacesReached(1502), circuitDoesNotExist(1503), circuitAlreadyExists(1504), circuitlessIpInterfacesOperationNotAllowed(1505), priority255SpecialForPhyIpSameAsVrIp(1506), icmpRdiscInvalidPreferenceLevel(1507), icmpRdiscAdvAddrIsNotBroadcastOrMulticastAddr(1508), icmpRdiscInvalidMaxAdvInt(1509), icmpRdiscMinAdvIntvGreaterThanMaxAdvIntvOrLessThan3Secs(1510), icmpRdiscLifeTimeLessThanMaxAdvIntvOrGreaterThan9000Secs(1511), vrrpInvalidFasterAdvertInterval(1512), vrrpFasterAdvEnabled(1513), vrrpFasterAdvDisabled(1514), vrrpInvalidFastAdvEnableValue(1515), globalFiltersNotSupportFwdingNextHopMode(1516), vrrpPreemptActionNotAllowed(1517), rcPimModeIgmpVersionIncompatible(1518), invalidOrInconsistentBroadCastMaskValue(1519), invalidRipTimeoutInterval(1520), rsmltNoCirc(1521), rsmltInvalidHoldUpTimer(1522), rsmltNoBrouter(1523), rsmltNoIst(1524), vrrpSetWithRsmltEnable(1527), rsmltSetWithVrrpEnable(1528), ipEcmpMaxPathExceeded(1530), ipEcmpPathListNotAllowedInRmode(1531), featureAppliesToRmodulePortsOnly(1532), invalidVrrpEntry(1533), invalidIpOwnerVrrpPrio(1534), circuitlessIpUsedByIpvpnRD(1537), ipAddressNotAssociatedWithVlan(1540), arpEntryNotFound(1541), arpDeleteSupportedOnlyForDynamicArps(1542), arpDeleteCannotDeleteArpWithRoutes(1543), arpMulticastMacAddressNotAllowed(1544), arpBroadcastMacAddressNotAllowed(1545), arpNoIpAddrAssociatedWithPort(1546), arpIncorrectIpAddress(1547), ipCircuitShouldExistForDhcpEnable(1548), webInvalidHttpsPort(1603), identicalHttpPortHttpsPortNotSupported(1604), invalidDdmMonitorInterval(1801), invalidDdmMonitor(1802), invalidDdmTrapsSend(1803), invalidDdmAlarmPortdown(1804), igmpOutOfSsmRange(2301), igmpDuplicateSsmTblEntry(2302), igmpSsmEntryDoesNotExist(2303), igmpSsmTblNotEmpty(2304), igmpRpSetExistsInSsmRange(2305), igmpCandidateRpExistsInSsmRange(2306), igmpIfInvalidQIntervalMrt(2307), igmpAlreadyEnabled(2308), igmpMaxStreamExceeded(2309), igmpStreamLimitAlreadyEnabled(2310), igmpStreamLimitNotEnabled(2311), igmpPimEnabledInSSMMode(2312), igmpDisableV3First(2313), igmpSSmConflictsWithSsgEntry(2314), igmpSsmCanNotDisableDynamicEntry(2315), invalidIpMulticastRange(2316), igmpStaticGroupCountExceeded(2317), igmpOverlappingStaticRangeNotAllowed(2319), igmpCannotEditStaticRecMcastDisabledGloballyOrOnVlan(2320), igmpMulticastRoutingEnabled(2321), igmpMVREnabled(2322), igmpMVRVlanIsMvrVlan(2323), igmpMVRVlanIsReceiverVlan(2324), igmpMVRVlanCanNotBeDeleted(2325), igmpMVRVlanReachMaximum(2326), igmpPortMaxStreamExceedsIntfMaxStream(2327), igmpQueryMaxResponseUnsupportedOnV1(2328), igmpMvrVlanIstSmlt(2331), igmpMvrVlanMlt(2332), portIsRequiredForIgmpStaticEntryCreation(2339), ipfStreamAlreadyExists(2401), ipfStreamDoesNotExists(2402), ipfStreamInvalidStreamType(2403), ipfStreamInvalidPortOption(2404), ipfStreamNameTooLong(2405), ipfStreamInvalidProtocol(2406), ipfStreamInvalidDscp(2407), ipfDeviceAlreadyExists(2408), ipfDeviceUnknownPlatform(2409), ipfDeviceUnknownDevice(2410), ipfDeviceDoesNotExists(2411), ipfDeviceNameTooLong(2412), ipfOneZeroIpDestFilterIsAllowed(2413), ipfGlobalFilterMaxPerOctapid(2414), ipfDeviceMaxPerPort(2415), ipfDeviceMaxPerBox(2416), ipfDeviceMaxFilterList(2417), ipfInvalidRmodPort(2418), ipfSourceNextHopModeNotSupported(2419), aclErrIdInvalid(2428), aclErrNameInvalid(2429), aclErrTypeInvalid(2430), aclErrNotExist(2431), aclErrInUse(2432), aclErrExists(2433), aceErrAceNotExist(2438), aceInvalidMode(2482), aceEgressqEgressqnnscInvalid(2483), cannotDeleteIntMltId(2501), mltNoThisVlan(2502), mltPortsDifferentFramingMode(2503), moreThan2PortsInMlt(2504), portCannotBeAddedToDefualtVLANWithIPXEnabled(2505), portMemberNotSupportSMLT(2506), tenGEMltPortOrMltCannotBeAddedToVlanWithSmltMember(2507), tenGEMltPortCannotRunTogetherWithSMLT(2508), portCannotBeAddedToDefualtVLANWithSMLT(2509), tenGEPortOrMltCannotBeAddedToVlanWithSmltMember(2510), tenGEPortOrMltCannotRunTogetherWithSMLT(2511), tenGEPortNotSupportMcastDistribution(2512), tenGEPortNotSupportMLT(2513), mltSmltIdAlreadyExists(2514), mltInvalidSmltId(2515), mltSmltNotConfigured(2516), mltSmltAlreadyConfigured(2517), mltPortIsMemberOfMlt(2518), mltPortIsMemberOfSmlt(2519), mltSmltIpAddrNotAllowedOnSltPort(2520), mltUsedForLacp(2521), mltPortUsedForLacp(2522), mltUsedForMlt(2523), operationNotAllowedOnMltPort(2529), mltNsnaUplinkMismatch(2538), mltIdInvalidInNonRmode(2539), mltNaapVlanCannotBeAddedToIst(2540), mltIstCannotBeCreatedOverMltWithNaapVlan(2541), mltNaapCannotBeAddedToMltWithActiveIst(2542), mltVrfVlanAndLegacyPortCannotBeMembers(2563), asListOverLimit(2601), communityListOverLimit(2602), mltSmltLacpInvalidKey(2603), extCommunityListOverLimit(2606), extCommunityInvalidListId(2607), extCommunityListIdExceedsRange(2608), mcastMltNotEnabled(2701), mcastMltInvalidSrcMask(2702), mcastMltInvalidGrpMask(2703), mcastMltRedistrNotEnabled(2704), mcastMltDiscontiguousSrcMaskValue(2705), mcastMltDiscontiguousGrpMaskValue(2706), mcastMltNotEnabledOnMlt(2707), mcastMltPortOnNonEtkt(2708), mcastMltConfMaskDisableMcastMlt(2709), ipmcTimePruneConflictsWithSsmEntry(2710), rcSnmpSyslogDisableSyslogFirst(2801), rcSnmpInvalidSyslogHeader(2802), dvmrpMBRNotAllowed(2901), dvmrpInvalidIntfTypeChange(2902), ipxPolicyNetEntryNotFound(3101), ipxPolicyNetDuplicateEntry(3102), ipxPolicyNetListEntryNotFound(3103), ipxPolicyNetListDuplicateEntry(3104), ipxPolicyServEntryNotFound(3105), ipxPolicyServDuplicateEntry(3106), ipxPolicyServeListEntryNotFound(3107), ipxPolicyServListDuplicateEntry(3108), ipxPolicyPolicyEntryNotFound(3109), ipxPlicyPolicyDuplicateEntry(3110), ipxRoutePolicyNetListOverLimit(3111), ipxRoutePolicyServListOverLimit(3112), ipxPolicyRipOutFilterEntryNotFound(3113), ipxPolicySapOutFilterEntryNotFound(3114), ipxPolicyRipInFilterEntryNotFound(3115), ipxPolicySapInFilterEntryNotFound(3116), ipxPolicyIpxNetEntryInvalidName(3117), ipxPolicyIpxServEntryInvalidName(3118), ipxPolicyPolicyEntryInvalidName(3119), vlanHas10GEMemberWhichNotSupportIPX(3120), vlanContainUnSupportedPrPort(3121), invalidLengthOf2kBootConfigLicenseSource(3401), licenseFileDoesNotExist(3402), licenseFileIsAlreadyLoaded(3405), invalidModeForAtmMDAType(3901), atmInvalidPVCEncapTypeForElan(3902), atmInvalidPVCPCRRange(3903), unsupportedVPI(3904), radiusAuthAcctAttrSame(4101), radiusAuthAcctPortSame(4102), radiusAuthAcctNoServerConfig(4103), radiusReAuthTimerFailed(4104), radiusAbortSesionTimerFailed(4105), radiusInvalidSnmpUserLength(4106), radiusInvalidCliCommandCount(4107), radiusAuthAcctNoServerButSnmpConfig(4112), pimGlobInvalidUniRouteChangeTimeOut(4801), pimGlobInvalidDiscDataTimeOut(4802), pimGlobInvalidCRPADVTimeOut(4803), pimGlobInvalidBootStrapPeriod(4804), pimStaticRpEnabled(4805), pimStaticRpNotEnabled(4806), pimStaticRpEntryExists(4807), pimStaticRpNoRoute(4808), pimAddressInSsmRange(4809), pimInvalidModeChange(4810), pimStaticRpNotAllowed(4811), pimMBRNotAllowed(4812), pimGlobInvalidActChkInterval(4813), pimGlobActChkIntervalNotAllowed(4814), pimGlobNotSuppActChkInterval(4817), pimVirtualNbrInvalidIfIndex(4818), rpsMcastMaskLenToNotAllowed(4901), rpsExtendedAclListNameInvalid(4902), rpsExtendedAclDuplicateEntry(4903), rpsExtendedAclListNotFound(4904), rpsExtendedAclEntryNotFound(4905), rpsExtendedAclDuplicateListFound(4906), tcpConnectionNotFound(5101), tcpInvalidState(5102), tcpSessionsInUse(5103), bgpPeerNotFound(5201), bgpInvalidPeerEnable(5202), bgpInvalidPeerRemoteas(5203), bgpInvalidPeerGroupName(5204), bgpInvalidPeerDefaultOriginate(5205), bgpInvalidPeerEbgpMultiNop(5206), bgpInvalidPeerAdvertisementInterval(5207), bgpInvalidPeerPassword(5208), bgpInvalidPeerWeight(5209), bgpInvalidPeerNextHopSelf(5210), bgpInvalidPeerRoutePolicyIn(5211), bgpInvalidPeerRoutePolicyOut(5212), bgpInvalidPeerRouteReflectorClient(5213), bgpInvalidPeerSoftReconfigurationIn(5214), bgpInvalidPeerSoftReconfiguration(5215), bgpInvalidPeerRemovePrivateAs(5216), bgpInvalidPeerRowStatus(5217), bgpNetworkNotFound(5218), bgpPeerGroupNotFound(5219), bgpInvalidPeerGroupEnable(5220), bgpInvalidPeerGroupRemoteAs(5221), bgpInvalidPeerGroupDefaultOriginate(5222), bgpInvalidPeerGroupUpdateSource(5223), bgpInvalidPeerGroupEbgpMultiHop(5224), bgpInvalidPeerGroupAdvertisementInterval(5225), bgpInvalidPeerGroupPassword(5226), bgpInvalidPeerGroupWeight(5227), bgpInvalidPeerGroupNextHopSelf(5228), bgpInvalidPeerGroupRoutePolicyIn(5229), bgpInvalidPeerGroupRoutePolicyOut(5230), bgpInvalidPeerGroupRouteReflectorClient(5231), bgpInvalidPeerGroupSoftReconfigurationIn(5232), bgpInvalidPeerGroupSoftReconfiguration(5233), bgpInvalidPeerGroupRemovePrivateAs(5234), bgpInvalidPeerGroupHoldTime(5235), bgpInvalidPeerGroupKeepAlive(5236), bgpInvalidPeerGroupRowStatus(5237), bgpInvalidPeerGroupGroupName(5238), bgpAggregateNotFound(5239), bgpInvalidAggregateAsSetGenerate(5240), bgpInvalidAggregateSummaryOnly(5241), bgpInvalidAggregateSuppressPolicy(5242), bgpInvalidAggregateAdvertisePolicy(5243), bgpInvalidAggregateAttributePolicy(5244), bgpOperationNotAllowedWhenBgpIsEnabled(5245), bgpInvalidPeerHoldTime(5246), bgpInvalidPeerKeepAlive(5247), bgpInvalidPeerMaxPrefix(5248), bgpInvalidPeerGroupMaxPrefix(5249), bgpInvalidPeerMD5Authentication(5250), bgpInvalidPeerGroupMD5Authentication(5251), bgpInvalidPeerGroupIndex(5252), bgpInvalidConfederationIdentifier(5253), bgpInvalidConfederationPeerAsNumber(5254), bgpInvalidConfederationPeerNotFound(5255), bgpInvalidConfederationPeerAlreadyExist(5256), bgpOperationNotAllowedWhenSoftReconfigInIsDisabled(5257), bgpNotAllowedSoftRecfgInIsDisabledForTheGrpOrAnyPeerInGrp(5258), bgpCanNotEnablePeerWithoutCfgRemoteAsForThePeer(5259), bgpCanNotEnablePeerGrpWoCfgRemoteASPeerGrpOrAnyPeerInGrp(5260), bgpOperationNotAllowedWhenPeerIsBGPON(5261), bgpOperationNotAllowedWhenPeerGrpOrAnyPeerInGrpIsBGPON(5262), bgpOperationNotAllowedExternalPeer(5263), bgpOperationNotAllowedInternalPeer(5264), asListNotFound(5265), asListDuplicate(5266), asListAsPathEntryNotFound(5267), asListAsPathEntryDuplicate(5268), asListInvalidModeOfAsPathEntry(5269), asListInvalidAsRegularExpressionOfAsPathEntry(5270), asListInvalidRowStatusOfAsPathEntry(5271), communityListNotFound(5272), communityListDuplicate(5273), communityListCommunityPathEntryNotFound(5274), communityListCommunityPathEntryDuplicate(5275), communityListInvalidModeOfCommunityPathEntry(5276), communityListInvalidValueOfCommunityEntry(5277), communityListInvalidRowStatusOfCommunityEntry(5278), bgpFeatureNotSupport(5279), bgpMd5EnabledWithoutPasswd(5280), bgpEnabledWithoutLocalAs(5281), bgpAggregateAdvertisePolicyWithoutAsSet(5282), bgpPeerHoldTimeLessThanKeepAliveTime(5283), bgpCommListCommunityStringUsed(5284), communityListModificationNotAllowed(5288), bgpInvalidPeerGroupAsOverride(5289), bgpInvalidPeerGroupAllowAsIn(5290), bgpInvalidPeerAllowAsIn(5291), bgpInvalidPeerAsOverride(5292), extCommunityListNotFound(5293), extCommunityListModificationNotAllowed(5294), extCommunityListInvalidEntry(5295), extCommunityListDuplicateMemberId(5296), extCommunityListInfoAlreadyExists(5297), extCommunityMemberNotFound(5298), bgpPeerLimitExceeded(5299), bgpPeerIpv6NotSupport(5301), sshEnableTrue(5501), rsaKeyNotExist(5502), dsaKeyNotExist(5503), rsaKeyGenMiss(5504), dsaKeyGenMiss(5505), sshShutDownInProcess(5506), sshInvalidPort(5507), sshPortAlreadyInUse(5508), sshPortReserved(5509), sshAuthenticationNotEnabled(5510), invalidOperationOnWsmOrSamStg(5601), invalidOperationOnWsmOrSamVlan(5602), invalidOperationOnWsmOrSamPort(5603), invalidOperationOnSamPort(5604), commandValidOnlyIfMezzCardIsPresent(5703), mplsInvalidRouterId(6109), lacpInvalidAggrsysPrio(6501), lacpInvalidAggrActorAdminKey(6502), lacpInvalidAggrColMaxDelay(6503), lacpInconsistentKey(6504), lacpInvalidVal(6505), lacpOutOfRangeKey(6506), lacpPortNotAggregatable(6507), lacpKeyModificationNotAllowedOnSltPort(6508), vlacpTimeoutScaleRangeBetween3To10(6509), lacpOtherPortsWithSameKey(6510), vlacpOneofPortorMLTIdIsRequired(6511), vlacpDuplicatePeerMacAddress(6512), vlacpOutOfRangeMac(6513), lacpSmltSysIdSyncIncomplete(6514), vlacpOperationReqPortVlacpDis(6515), lacpNotAllowedForSmlt(6516), lacpCantCreateSmlt(6517), macAddrHasBeenAddedToGlobalFilter(6526), vlacpEtherTypeIsInvalid(6527), mirrorByPortNonExistingEntry(6711), targetAddressMissing(6801), testAlreadyRunning(6802), invalidTargetAddress(6803), invalidSourceAddress(6804), controlEntryAlreadyExists(6805), invalidIpAddressFormat(6806), invalidDataRange(6807), invalidIndex(6808), entryDoesNotExist(6809), controlEntryMaxLimitReached(6810), maxRowOutOfRange(6811), ipv6VlanDoesnotExist(7401), ipv6InvalidInstance(7402), ipv6InvalidParameter(7403), ipv6AttrNotImplemented(7404), ipv6EntryDuplicate(7405), ipv6EntryNotExist(7406), ipv6InvalidIdentifierLength(7407), ipv6CircuitDoesNotExist(7408), ipv6PortNotPowerRanger(7409), ipv6InvalidInterfaceIdentifier(7410), ipv6CannotChangeWhenAdminEnable(7411), ipv6InvalidReasmMaxSize(7412), ipv6InvalidReachableTime(7413), ipv6InvalidPrefixLength(7414), ipv6InvalidSendAdverts(7415), ipv6InvalidMaxInterval(7416), ipv6InvalidMinInterval(7417), ipv6InvalidRetransmitTimer(7418), ipv6InvalidDefaultLifeTime(7419), ipv6InvalidCurHopLimit(7420), ipv6InvalidManagedFlag(7421), ipv6InvalidOtherConfigFlag(7422), ipv6InvalidDadNsNum(7423), ipv6InvalidPhysicalAddress(7424), ipv6InvalidNetToPhysicalType(7425), ipv6NeighborDuplicate(7426), ipv6NeighborDoesNotExist(7427), ipv6InvalidInvalidIpv6Addr(7428), ipv6PrefixDuplicate(7429), ipv6InvalidPrefix(7430), ipv6InvalidInterfaceType(7431), ipv6NexthopOrIndexReq(7432), ipv6NexthopIsLinklocBothIndexHopReq(7433), ipv6StaticRouteDistanceReq(7434), ipv6StaticRouteDuplicate(7435), ipv6StaticRouteInvalid(7436), ipv6OspfInvalidRouterId(7437), ipv6OspfNotSupported(7438), ipv6OspfAreaDoesNotExist(7439), ipv6OspfAlreadyExist(7440), ipv6OspfInterfaceInvalid(7441), ipv6OspfInterfaceExists(7442), ipv6OspfInterfaceNotExists(7443), ipv6OspfAreaAggregateEntryExists(7444), ipv6OspfAreaAggregateEntryDoesNotExist(7445), ipv6OspfInvalidAreaRangeMask(7446), ipv6OspfAreaCannotModifyBackbone(7447), tcpConnectTblPermittedStateIsDelete(7448), ipv6InterfaceVlanNotFound(7449), ipv6TunnelInterfaceDoesnotExist(7450), ipv6TunnelNotImplemented(7451), ipv6TunnelInvalidOperation(7452), ipv6TunnelInvalidType(7453), ipv6TunnelInterfaceAlreadyExist(7454), ipv6TunnelRemAddrShldBeZero(7455), ipv6VlanDoesNotMatchPreviousVlanid(7456), ipv6UvifDoesNotExist(7457), ipv6MldNotEnabled(7458), ipv6MldInterfaceExists(7459), ipv6MldInterfaceDoesNotExist(7460), ipv6MldInvalidQueryInterval(7461), ipv6MldInvalidVersion(7462), ipv6MldInvalidMaxRespdelay(7463), ipv6MldInvalidRobvar(7464), ipv6MldInvalidLlqi(7465), ipv6RedistributionInvalidOperation(7466), ipv6InvalidMaxRouterAdvertInterval(7467), ipv6InvalidMinRouterAdvertInterval(7468), ipv6CannotSetSummaryAsFalseIfNotStubArea(7469), ipv6CannotModifyStubMetricIfNotStubArea(7470), ipv6GatewayMustBeOnMgmtInterface(7471), ipv6OspfNbmaNbrAlreadyExist(7472), ipv6OspfInterfaceNotNbma(7473), ipv6OspfNbmaTunnelNot624(7474), ipv6OspfNbmaNbrNotExist(7475), cannotConfigureAddrWhichIsLinkLocal(7476), addrEntryDoesNotExist(7477), ipv6TunnelCannotHaveMoreThanOneAddr(7478), cannotChangeAddressType(7479), cannotConfigureNetAddr(7480), invalidInetNetworkAndMask(7481), cannotConfigureHostAddr(7482), ipv6InterfaceIdCannotBeChanged(7483), ipv6TunnelLocalAndRemoteIpAddressCannotBeSame(7484), ipv6StaticRouteWrongNexthop(7485), ipv6EuiInterfacePrefixCannotBeGreaterThan64(7486), ipv6CircuitMcastFlagNotSet(7487), ipv6MldProxyUnsupported(7488), ipv6MtuChangeWhenIntfDisable(7489), ipv6OspfNbmaNbrInvalidAddress(7490), ipv6AddressAndPrefixSame(7491), ipv6IncompatibleAddressTypeAndAddress(7492), ipv6DadInProgressTryLater(7493), ipv6InterfaceMismatch(7494), ipv6StaticNeighborInterfaceNotPresent(7495), ipv6RequiresSuperMezz(7496), ipv6StaticRouteOnlyIfindexCannotConfigPref(7497), ipv6StaticRouteRecursiveRouteNotSupported(7498), ipv6TunnelLocalRemoteAddrPairAlreadyExists(7499), cannotConfigureBothNetAndHostAddr(7510), idInvalid(7501), notExist(7502), duplicate(7503), nameInvalid(7504), notenablemixedmlt(7505), portconflictmixedmlt(7506), actInUse(7601), actFieldTooMany(7602), actPatternNotExist(7603), actErrApplyStateTrue(7604), actMaxPatternExceeded(7605), aclActNotExist(7606), aclTypeInvalid(7607), aclDefActionInvalid(7608), aclGlobActionInvalid(7609), vlanInvalid(7610), portInvalid(7611), aclMltInvalid(7612), aclInUse(7613), aclInvalidState(7614), aclActNotApplied(7615), aclActVlanAttrSpecified(7616), aclActPortAttrSpecified(7617), aclPortBased(7618), aclVlanBased(7619), actNoAttributesConfigured(7620), aclErrPortAlreadyInAcl(7621), aclErrVlanAlreadyInAcl(7622), aceAclIdInvalid(7623), aceAclNotExist(7624), aceInUse(7625), aceMax(7626), aceModeIllegal(7627), aceDscpIllegal(7628), aceDot1pIllegal(7629), aceUnreachIllegal(7630), acePoliceIllegal(7631), aceAclInvlanPoliceNotAllLanes(7632), aceInvalidAdminState(7633), aceEgressQueueInvalid(7634), aceEgressQueue1gInvalid(7635), aceEgressQueue10gInvalid(7636), aceEgressNNSCInvalid(7637), acePoliceInvalidMode(7638), aceAttrNotExistInAct(7639), aceInsuffActionAttr(7640), maxAceForSystem(7641), aceValMoreThanActPatternLen(7642), aceMltIndexIllegal(7643), aceModeNotPermit(7644), aceNotPermitIngress(7645), aceParmNotDefault(7646), aceAttrConflict(7647), defaultIdnoCreate(7648), defaultIdnoDelete(7649), defaultIdnoModify(7650), mltPortAclConflict(7651), aceNoModeModify(7652), aclNoAccept(7653), aceDebugMirrorDisableToRemoveDest(7658), actPatternWrongIpVersion(7678), qosPolicyLaneExist(7701), qosPolicyLaneNotExist(7702), qosPolicyPkRateInvalid(7703), qosPolicySvcRateInvalid(7704), qosPolicyLaneInvalid(7705), qosPolicyValidAcesPresent(7706), qosTxQSetQmaxInvalid(7707), qosTxQSetQmaxChangeNotAllowed(7708), qosTxQSetBalQInvalid(7709), qosTxQSetHipriQInvalid(7710), qosTxQSetLopriQInvalid(7711), qosTxQSetMaxQExceed(7712), qosTxQSetPortNotRMod(7713), qosTxQSetQInvalid(7714), qosTxQSetQNotAssign(7715), qosTxQSetMinRateGtMaxrate(7716), qosTxQSetQMaxAfter8Adjust(7717), qosTxQSetPortFeIncompatibleQset64(7718), qosTxQSetPortGbIncompatibleQset8(7719), qosTxQSetModificationNotAllowed(7720), qosTxQSetQLengthWredModNotAllowed(7721), qosTxQSetQLengthZeroNotAllowed(7768), qosTxQSetQLengthLessThanDefaultNotAllowed(7769), qosTxQSetQCannotBeCreated(7770), qosTxQSetQCannotBeDeleted(7771), ipv6InterfaceAdminDisabled(7802), ipv6ForwadingDisabled(7803), noVrrpLinkLocalAddressSpecified(7804), vrrpLinkLocalAddressCannotBeChanged(7805), vrrpInvalidGlobalAddress(7806), invalidLinkLocalAddress(7807), addressExistsOnVrrp(7808), invalidVrrpAddressOwnerPriority(7809), ipv6ValidLifeCanOnlyBeInfinityForInfinite(7810), invalidVrrpPrefixEntry(7811), vrrpPrefixExists(7812), ipfixStateAlreadyEnabled(8101), ipfixStateAlreadyDisabled(8102), ipfixInvalidSlotNumber(8103), ipfixNotADPMSlot(8104), ipfixInvalidActiveTimeout(8105), ipfixInvalidAgingInterval(8106), ipfixInvalidExportInterval(8107), ipfixInvalidTemplateRefIntervalSec(8108), ipfixInvalidTemplateRefIntervalPkts(8109), ipfixCollectorNotConfigured(8110), ipfixTwoCollectorAlreadyConfigured(8111), ipfixOnlyUdpProtocolSupported(8112), ipfixInvalidCollectorDestPort(8113), ipfixInvalidHashPolynomialCoeff(8114), ipfixInvalidHashPolynomialSeed(8115), ipfixInvalidHashKeyId(8116), ipfixInvalidSamplingRate(8117), aceIpfixStateIllegal(8118), tacacsIllegalIpAddress(8201), tacacsIllegalPriority(8202), tacacsMaxServersReached(8203), tacacsRadiusEnabled(8204), tacacsNoKeyGiven(8205), tacacsSourceIpDisabled(8207), tacacsServerNotConfigured(8209), tacacsPrimaryServerAlreadyExists(8210), tacacsBackupServerAlreadyExists(8211), tacacsPrimaryServerIsConfiguredWithTheSameIp(8212), tacacsBackupServerIsConfiguredWithTheSameIp(8213), isisPwdInvalid(8301), isisKeyIdInvalid(8302), isisPwdExists(8303), isisNoKeyId(8304), isisInvalidAuthType(8305), isisCsnpIntInvalid(8306), isisRxmtLspIntInvalid(8307), isisRtrTypeInvalid(8308), isisNetLenInvalid(8309), isisSysidError(8310), isisManAreaAddrToomany(8311), isisManAreaError(8312), isisNetEntryExists(8313), isisSummAddrExists(8314), isisSummAddrError(8315), isisInvalidSubnetMask(8316), isisEnabledOnInterface(8317), isisCannotChangeMetricTypeFromWideToNarrow(8318), isisInvalidCircType(8319), isisSysIdInvalid(8320), isisSysIdRuntimeChange(8321), isisInvalidCircuitId(8322), isisCircuitAlreadyExists(8323), isisCircuitDoesNotExist(8324), isisInvalidIntfIndex(8325), isisLevelRouterDoesNotSupp(8326), isisManAreaNotConfigured(8327), isisL2OnlyNotSupported(8328), isisPriorityOnlyForBcastType(8329), isisMetricValueInvalidForNarrowType(8330), isisL2onlyCircuitExists(8331), isisMinLspIntGreaterThanMaxLspInt(8332), isisMaxLspIntLessThanMinLspInt(8333), isisPlsbNodeNicknameInvalid(8334), isisPlsbInstanceAlreadyExists(8335), isisOnePlsbInstanceAllowed(8336), isisPlsbInstanceDoesNotExist(8337), isisCannotDeletePlsbInstanceWithIsid(8338), isisCannotDeletePlsbInstanceWithIsisInterface(8339), isisOneVlanPerPlsbInstance(8340), isisVlanDoesNotExist(8341), isisVlanIsNotPlsb(8342), isisInterfaceCannotConfigPlsb(8343), isisPlsbInstanceNotExistOnInterface(8344), isisPlsbInstancePt2ptOnly(8345), isisPlsbL1Only(8346), isisCannotDeleteVlanWithPlsb(8347), isisPlsbNniPortCannotBeAccess(8348), isisCannotEnableInterfaceWithoutPlsbInstance(8349), isisSystemIdIsnotBasemac(8350), isisPlsbInstanceNotConfigured(8351), isisNicknameNotConfiguredForPlsbInstance(8352), isisBvidNotConfiguredForPlsbInstance(8353), isisSpfDelayInvalid(8354), isisControlVlanDoesNotExist(8355), cannotAddPortToMltWithIsisInterfaceOnBothPortAndMlt(8356), cannotCreateIsisIntfOnPortWhichIsMemberOfMltWithIsisIntf(8357), cannotCreateIsisIntfOnMltWhichHasPortMemberWithIsisIntf(8358), isisSysidCannotBeMulticastAddress(8359), deleteIsisInterfaceBeforeDeleteMlt(8360), onlyFirst10PortOfLaneCanBeIsisInterface(8361), narrowMetricNotSupportedInPlsbMode(8362), isisCannotChangeSysIdDueToIsidEpIsEnable(8363), isisCannotChangeNickNameDueToIsidEpIsEnable(8364), isisCannotChangePlsbVlanDueToIsidEpIsEnable(8365), isisBcastNotSupportedOverMlt(8366), isisPortIsNotMemberOfPlsbVlan(8367), isisMltIsNotMemberOfPlsbVlan(8368), isisPlsbVlanDifferentFromDataVlan(8369), isisOverloadOnStartUpOutOfRange(8370), isisCannotChangeSysIdWhenNodalMepMipAssociatedToPlsbVlan(8371), enablePerformTaggingBefPlsbIsisInterfAssociation(8372), isisPlsbPrimaryVlanNotAdded(8373), isisPlsbPrimaryVlanNotMatch(8374), isisCannotUseMulticastAddress(8375), isisCannotEnableIpIsis(8376), isisPlsbPortConflictWithCvlan(8377), isisPlsbMLTConflictWithCvlan(8378), isisPlsbMLTISTConflictWithCvlan(8379), isisSpbmBvlanNotAllowToRunSlpp(8380), isisSpbmInvalidEtherType(8381), nsnaNoRedVlan(8401), nsnaRedVlanExists(8402), nsnaGlobalEnabled(8403), nsnaNoVlanColor(8404), nsnaVlanHasColor(8405), nsnaVlanNonEmpty(8406), nsnaNoFilterForNsnaVlan(8407), nsnaPortHasFilter(8408), nsnaNoUplinkDhcpFilter(8409), nsnaYellowSubnetNotSpecified(8410), nsnaNoNsnasSubnet(8411), nsnaMaxNsnasSubnet(8412), nsnaNoSshDaemon(8413), nsnaIncorrectGreenVlan(8414), nsnaIncorrectUplinkVlan(8415), nsnaIncorrectVoipVlan(8416), nsnaPortIsEap(8417), nsnaPortOperationNotAllowed(8418), nsnaUnknownMac(8419), nsnaExceedMaxNumEntry(8420), nsnaStaticEntryExists(8421), nsnaOperationNotAllowedOnMirroredPort(8422), nsnaInvalidHelloInact(8423), nsnaVlanFlushNotAllowed(8424), nsnaNoUplinkVlans(8425), nsnaVlanFilterRemapInProgress(8426), nsnaVlansCannotBeDeleted(8427), nsnaVlanCannotBeMadeGuestVlan(8428), nsnaPortCannotBeConfiguredOnNonPrPorts(8429), nsnaNotAllowedOnSmltPort(8431), cfmNoParamChange(8501), cfmDomainExists(8502), cfmDomainDoesNotExists(8503), cfmMaintenanceAssociationExists(8504), cfmMaintenanceAssociationDoesNotExists(8505), cfmChangeNotAllowedWhenEnabled(8506), cfmMepExists(8507), cfmMepDoesNotExists(8508), cfmOperationNotAllowedWhenMepsExist(8511), cfmMepInUse(8531), cfmMaDomainNameFieldCannotBeEmptyForCreation(8535), indexIsBeingUsedByOtherDomain(8536), cfmAssnIndexCantBeZeroForCreation(8537), indexIsBeingUsedByOtherMaAssn(8538), cfmOperationNotAllowedWhenMasExistUnderMd(8539), cfmDomainIndexCantBeZeroForCreation(8540), cfmAssnDoesNotExist(8541), cfmMepIdCannotBeNullForCreation(8542), cfmMaAssnNameFieldCannotBeEmptyForCreation(8543), pbtVlanCannotReassign(8552), cfmMepCanNotEnableWhenCfmEtherTypeIsNotSet(8554), invalidMepListInputFormat(8562), invalidDmOrMaNameLength(8563), mepIdMustBeANumber(8564), maxNumOfMepEntriesExceeded(8565), domainAlreadyAssociatedWithOtherTypeOfService(8567), cfmCannotDeleteBeforeRemoveAssociation(8574), cfmOperationNotAllowedWhenMipsExistUnderMd(8577), invalidMipListInputFormat(8582), invalidDmNameLength(8583), cannotDeleteVlanWithMepAssociation(8586), cfmLbmExceedMaxDataSizeLimit(8642), plsbVlanMustUsePlsbStg(8646), normalVlanCannotUsePlsbStg(8647), cfmPlsbCanHaveOnlyOneStg(8648), cfmInvalidName(8649), sameLevelMepAlreadyAssignedToVlanOnSamePort(8670), sameLevelMipAlreadyAssignedToVlanOnSamePort(8671), cfmNodalMepOnPbtVlanNotAllowed(8687), cfmCannotAddOrRemoveNodalMepsWhenMepListIsEmptyOrInvalid(8688), cfmExceedMinCcmIntervalForNodalVlan(8689), cfmMepAlreadyInUseWithOtherNodalVlan(8690), cfmMepAlreadyInUseWithOtherServiceType(8691), cfmNodalMipLevelOnPbtVlanNotAllowed(8692), cfmCannotAddOrRemoveNodalMipsWhenMipListIsEmptyOrInvalid(8693), cfmLbmCannotSpecifyBothDataAndFrameSize(8697), cfmFrameSizeTooLargeForRmod(8698), cfmFrameSizeTooLargeForRCmod(8699), cfmNoServiceAssociatedWithMepOrMip(8720), cfmMepNotReadyToSetLbm(8721), cfmMepNotOkToSetReady(8722), cfmMepNotReadyToSetLtm(8723), cfmLbmExceedMaxMessagesLimit(8726), cfmLbmTestPatternSizeError(8748), mepListCannotHaveTwoMepsWithSameMdLevel(8754), mipListCannotHaveTwoMipsWithSameMdLevel(8755), vrfDoesNotExist(8901), vrfAlreadyExists(8902), vrfMaxRoutesCouldNotBeSet(8903), vrfPortDoesNotBelongToSpecifiedVrf(8904), vrfVlanDoesNotBelongToSpecifiedVrf(8905), vrfLegacyPortCannotBeAddedToVlanAssociatedWithVrf(8906), vrfInvalidVrfId(8908), vrfOperationProhibitedForGrt(8909), vrfOspfLimitExceeded(8910), vrfRipLimitExceeded(8911), vrfDhcpLimitExceeded(8912), vrfVrrpLimitExceeded(8913), vrfRipDoesNotExist(8914), vrfOspfDoesNotExist(8915), vrfNameInvalid(8916), vrfNameDuplicate(8917), vrfRipAlreadyExists(8918), vrfOspfAlreadyExists(8919), vrfCannotChangeAssociationInterfaceExists(8907), vrfCannotAssociatePortInVlan(8920), vrfCannotAddAssociatedPortToVlan(8921), vrfCannotAssociateToVlanWithLegacyPorts(8922), vrfCannotAssociateToLegacyPortForBrouter(8923), vrfBgpDoesNotExist(8924), vrfBgpAlreadyExists(8925), vrfBgpLimitExceeded(8926), vrfConfigNeedsMezz(8927), invalidNextHopVrfName(8928), vrfOperationNotAllowed(8931), vrfPimLimitExceeded(8932), vrfPimDoesNotExist(8933), igapCannotBeEnabledOnNonGRTVlan(8934), igapAuthCannotBeEnabledOnNonGRTVlan(8935), igapAccntCannotBeEnabledOnNonGRTVlan(8936), igapIsNotEnabled(8937), mplsRouterIdLdpRsvpEnabled(10001), mplsInvalidDeleteOperation(10002), mplsInvalidInterfaceState(10003), mplsInterfaceNotExist(10004), mplsInvalidInterfaceMtu(10005), mplsExplicitPathInUse(10006), mplsTunnelInUse(10007), mplsTunnelNoDest(10008), mplsTunnelResourceInUse(10009), mplsMezzCardAbsent(10010), mplsLdpNotReady(10011), mplsRsvpNotReady(10012), mplsRouterIdSetToZero(10013), mplsInterfaceVlanNotFound(10014), mplsPortNotRModule(10015), mplsIpAddrInUse(10016), mplsTunnelNotFound(10017), mplsTunnelNotAllLspUp(10018), mplsInvalidIndex(10019), mplsExplicitPathExists(10020), mplsExplicitPathHopExists(10021), mplsExplicitPathIndexExists(10022), mplsMaxIndex(10023), mplsInvalidPathOptionIndex(10024), mplsLspExists(10025), mplsInvalidLspInstance(10026), mplsLspNoName(10027), mplsLspNoEPName(10028), mplsLspEPNotFound(10029), mplsConfigNeedsMezz(10030), mplsExpPathIpv4AddrTypeOnly(10031), mplsExpPathNoNameChange(10032), mplsLspNoNameChange(10033), mplsSrcIpNonLocal(10034), mplsLspIndexUsed(10035), mplsLspNameUsed(10036), mplsLspNotActive(10037), mplsTunnelSameSrcDest(10038), mplsLspNotSameSrc(10039), mplsLspNotSameDest(10040), mplsTunnelNoALtPath(10041), mplsTunnelCfgIngressOnly(10042), mplsTunnelInvalidIndex(10043), mplsEPInvalidIndex(10044), mplsEPHopInvalidIndex(10045), mplsResInvalidIndex(10046), mplsInvalidLdpKeepAliveRange(10047), mplsInvalidLdpHelloHoldTimeRange(10048), ipInterfaceMustExistsBeforeEnablingMpls(10058), multinetVlanDoesNotExist(11701), multinetVlanPortMustBeTagged(11702), multinetVlanHasIpSubnetVlanAssociated(11703), multinetVlanAssignPortToMultipleIpMultinetVlan(11704), multinetVlanCannotHaveLegacyPort(11705), multinetVlanHasMltMember(11706), multinetVlanCannotHaveBrouterPort(11707), multinetVlanCannotBeModified(11708), multinetAssoVlanCannotBeModified(11709), multinetVlanOnPortBasedVlanOnly(11710), multinetAssoVlanOnIpsubnetVlanOnly(11711), ipvpnCreateFailed(10201), ipvpnDeleteFailed(10202), ipvpnAlreadyEnabled(10203), ipvpnNotEnabled(10204), ipvpnNotSupportedOnDefVRF(10205), ipvpnSameRDConf(10206), ipvpnInvRDConfOnDefVRF(10207), ipvpnInvRDTypeNotSupported(10208), ipvpnInvRTConfOnDefVRF(10209), ipvpnInvRTTypeNotSupported(10210), ipvpnSVCAllocFailed(10211), ipvpnSVCILMAddFailed(10212), ipvpnLiteSupportOnlyType1(10213), ipvpnRDTypeNotSupportedWithLite(10214), ipvpnSvcLblChngIfIpvpnDisabledInVRF(10215), ipvpnSvcLblOptionAlreadySetInIpvpnVRF(10216), ipvpnPeerRRLiteModeConflict(10217), ipvpnPeerGroupRRLiteModeConflict(10218), ipvpnImplicitReflectInMixedLiteMode(10219), ipvpnInvalidPeerSetForAccessPeer(10220), ipvpnRouterInNonLiteRRMode(10221), ipvpnRouteTargetNotFound(10222), bgpOperationNotAllowedWhenDefaultBgpIsEnabled(10223), bgpOperationNotAllowedWhenVrfBgpIsEnabled(10224), bgpInvalidLocalAsWhenVrfPeerRemoteAs(10225), bgpInvalidVrfPeerRemoteAs(10226), bgpInvalidVrfPeerGroupRemoteAs(10227), ipvpnLiteRequiresVpnv4(10228), ipvpnVpnv4DisableRequiresLiteDisable(10229), ipvpnEnabledWithoutLocalAs(10230), ipvpnInterVrfRedistEnable(10231), bgpOperationNotAllowedWhenIpvpnIsEnabled(10232), ipvpnInvalidAssignedNumber(10233), ipvpnInvalidAsNumber(10234), ipvpnInvalidPeerSetForExternalPeer(10235), ipvpnInvalidPeerGroupSetForExternalPeer(10236), ipvpnMaxRtPerVrfExceeded(10237), ipvpnRdOverlapOperNotAllowed(10238), ipvpnNotCreated(10239), ipvpnAlreadyCreated(10240), ipvpnLiteRequiresValidIpAddressInRd(10241), ipvpnLiteOperationNotAllowedSameIpConfiguredAsRdInAnotherVrf(10242), ipvpnRDInvalidCircuitlessIP(10243), ipvpnRDIpNotLiteEnabled(10244), ipvpnLiteSupportRDWithClipIp(10245), ipvpnLiteSupportOnlyLiteEnabledRDIP(10246), ipvpnEnableDisallowedWithoutValidRD(10247), ipvpnLiteRDIpConfiguredInMultipleVrf(10248), ipvpnIsidAlreadyExist(10249), ipvpnBgpBasedOrTaggedPeerNotConfigured(10250), ipvpnBothTypeOfIpvpnCreated(10251), ipvpnBgpBasedAlreadyCreated(10252), ipvpnTaggedPeerAlreadyCreated(10253), ipvpnTaggedPeerIsidNotConfigured(10254), ipvpnTaggedPeerIsidRuntimeChangeNotAllowed(10255), customAutoNegAdvMacPauseNotSupported(10301), customAutoNegAdvAsymPauseNotSupported(10302), mirrorDestinationNotEntered(10306), mirrorLegacyCannotSupportPortList(10307), mirrorMltShouldHavePortsAssigned(10308), mirrorDestinationNotAttached(10309), mirrorDisableEntry(10310), mirrorDestinationAlreadyAttached(10311), mirrorLegacyCannotSupportVlanOrMlt(10313), mirrorDestAlreadyAttachedOrDestSpecifiedNotAttached(10314), noAdminSettingForSpeed1000(10330), portAlwaysRunAt10GSpeed(10331), cannotSetAdminSpeed1000AsPerIEEE(10338), portCustomAutoNegAdv1000HalfInvalid(10370), cannotSetDuplexWhenSpeedIs1000(10371), invalidAdminSpeedCannotDisableAutoneg(10372), plsbVlanIsidNotAllowed(10459), plsbVlanIsidAlreadyExist(10460), plsbVlanIsidWithSingleBvlan(10461), plsbSysidCannotBeSameAsIstPeerSysid(10462), bgpInvalidPeerSetWhenVpnv4Enabled(10501), bgpInvalidPeerGroupSetWhenVpnv4Enabled(10502), bgpOverlappingAggregateAddress(10503), bgpInvalidLocalAsWhenPeerRemovePrivateAsEnabled(10504), bgpInvalidPeerRemovePrivateAsEnableWithoutRemoteAs(10505), bgpInvalidPeerGroupRemovePrivateAsEnableWithoutRemoteAs(10506), bgpDuplicatePeerNotAllowed(10507), bgpPeerDoesNotBelongToPeerGroup(10508), bgpOperationNotAllowedWhenRouteReflectorClientIsEnabled(10509), bgpInvalidAggregateAdvertisePolicyWithoutAsSetGenerate(10510), bgpInvalidPeerDefaultOriginateIpv6(10512), bgpInvalidPeerGroupDefaultOriginateIpv6(10513), bgpInvalidPeerIpv6Capability(10514), bgpOperationNotAllowedForIpv6Peer(10515), bgpOperationNotAllowedForIpv6PeerGroup(10516), bgpOperationNotAllowedWhenOutboundMapsAreDifferent(10517), bgpOperationNotAllowedWhenInboundMapsAreDifferent(10518), maxPeerEntriesInPeerGroup(10519), rmodOnlyOneMirroredPortPerLaneForEgress(10332), mirrorTxFilterModeNotAllowedOnRsmod(10333), mirrorModeNotValidForRmodRSmod(10334), msdpInconsistentRowStatus(10801), msdpInvalidRPAddress(10802), msdpRPAddressNotLocalAddress(10803), msdpPeerTableInvalidLocalAddress(10804), msdpNotLocalAddress(10805), msdpLocalAddressPeerEstablished(10806), msdpPeerCreated(10807), msdpInconsistentPeerRowStatus(10808), msdpPeerNotFound(10809), msdpInvalidConnectRetryPeriod(10810), msdpHoldTimePeerEstablished(10811), msdpInvalidHoldtimePeriod(10812), msdpKeepAliveTimePeerEstablished(10813), msdpPeerKeepAliveInvalid(10814), msdpDataTTLInvalid(10815), msdpEncapsulationTypeNotSupported(10816), msdpPeerSARouteMapNameLenInvalid(10817), msdpPeerSAFilterPolicyNotFound(10818), msdpInvalidDescriptionLength(10819), msdpInvalidSALimit(10820), msdpInvalidMD5AuthStatus(10821), msdpInvalidPeerSetWhenPeerIsEnabled(10822), msdpInvalidPeerAddress(10823), msdpInvalidMD5AuthPasswordLength(10824), msdpInvalidASnumber(10825), msdpPeerNotConfigured(10826), msdpInvalidDefaultPeerRouteMapNameLength(10827), msdpDefaultPeerRoutePolicyNotFound(10828), msdpInvalidRedistributeRouteMapNameLength(10829), msdpRedistributeRoutePolicyNotFound(10830), msdpInvalidMeshGroupNameLength(10831), msdpPeerAlreadyConfiguredInMeshGroup(10832), msdpPeerNotFoundInMeshGroup(10833), msdpInconsistentPeerAdminStatus(10834), msdpInconsistentDefaultPeerStatus(10835), msdpInconsistentRedistributeRowStatus(10836), msdpInconsistentMeshGroupRowStatus(10837), msdpInvalidPeerAddressInMeshGroup(10838), msdpDefaultPeerAlreadyCreated(10839), msdpPeerSAFilterNotFound(10840), msdpGlobalGrpRedistributeNotFound(10841), msdpPeerSAFilterAlreadyCreated(10842), msdpGlobalGrpRedistributeAlreadyCreated(10843), msdpInterfaceNotUp(10844), msdpPeerConfigurePassword(10845), msdpPeerControlCharNotAllowed(10846), msdpPeerCannotDeleteNonExistingPasswd(10847), dhcpDhcpSnGlobalDisabled(11101), dhcpPortBelongToDhcpSnDisabledVlan(11102), dhcpPortBelongToDaiDsabledVlan(11103), dhcpPortIsDhcpSnTrusted(11104), dhcpPortIsDaiTrusted(11105), dhcpIpsgEnabledOnDaiVlanMember(11106), dhcpIpsgEnabledOnDaiUntrustedPort(11107), dhcpMltPortDifferentDhcpSnType(11108), dhcpMltPortDifferentDaiType(11109), dhcpMltPortDifferentIpSourceGuardType(11110), dhcpMltPortDifferentDhcpSnDaiType(11111), dhcpIpsgEnabledOnSomePorts(11112), dhcpIpsgEnabledOnDhcpSnVlanMember(11113), dhcpIpsgEnabledOnDhcpSnUntrustedPort(11114), dhcpSnoopingStaticBindingEntryExist(11120), dhcpSnoopingStaticBindingEntryDoesNotExist(11121), cannotChangeDhcpSnoopingDynamicBindingEntryIp(11122), cannotChangeDhcpSnoopingDynamicBindingEntryInterface(11123), dhcpSnoopingBindingCannotOnDhcpSnoopDisabledVlan(11124), dhcpSameServerAgentAddress(11226), dhcpDiffAgentAddress(11227), bfdMultiplierInvalidValue(11501), bpduFilterTimerInvalidRange(11502), bfdIsOnlySupportedOnGRTBgpPeer(11503), plsbDeleteIntfBeforeSetPlsbFlag(10701), plsbDeletePlsbInstanceBeforeSetPlsbFlag(10702), plsbDeleteManualAreaBeforeSetPlsbFlag(10703), plsbDeleteSummaryAddrBeforeSetPlsbFlag(10704), plsbDisableIsisBeforeSetPlsbFlag(10705), plsbDeletePlsbVlanBeforeSetPlsbFlag(10706), plsbCannotConfigPlsbInNonplsbMode(10707), commandValidOnlyIfInRmode(10708), cannotAssociateMoreThan5000IsidToPlsbInstance(10709), cannotEnablePlsbWithMmrpConfiguration(10711), cannotHaveSameBvlanAsSpIpVlanRCModPort(10712), cannotAddRcModPortsToMltWhenSpIpVlanSameAsBvlan(10713), cannotConfigPlsbIsisSmltistIntfOnSameIntf(10714), plsbDisableAllIsisEndpointsBeforeTogglePlsbState(10715), cannotConfigPortInSmltOrIstForPlsbVlan(10716), deleteStg63BeforeCreatingPlsbBvlan(10717), only2PlsbBvlanSupported(10718), plsbInvalidIpSourceAddress(10719), plsbMustChangeNicknameAfterChangeSysid(10720), plsbWhenEnableIstMustConfigSmltPeerBmac(10721), cannotConfigPlsbIsisIntfOnSmlt(10722), cannotConfigPlsbIsisIntfOnIstPort(10723), plsbZeroSmltPeerBmacMustHaveZeroVirtualBmac(10724), plsbZeroSmltPeerBmacMustHavePrimSplitBeb(10725), plsbWhenSetVirtualBmacToZeroPeerBmacMustBeZero(10726), plsbDeleteIsidFromVlanBeforeSetPlsbFlag(10727), plsbIsidNotAllowedForVlanSpbmDisabled(10728), plsb16777215IsWellKnownIsid(10729), plsbConfigIpSourceAddrBeforeEnableIpSc(10730), inUsedAsIsisIpSourceAddr(10731), plsbCannotSetIpSourceAddrToZeroWhenIpScEnabled(10732), cfmCannotAbortWhenNoLtmInProgress(10442), esmMltCannotBeNonUni(10443), cfmCannotAbortWhenNoLbmInProgress(10446), cfmLbmFrameTooSmall(11401), cfmLbmExceedsChassisMtu(11402), cfmLbmExceedsUniPortMtu(11403), cfmNodalMepIsNotSupportedOnESM(11408), cfmNodalMipLevelIsNotSupportedOnESM(11409), cfmLbmFrameSizeExceedMaxForNodalMep(11414), cannotDeleteVlanWithNodalMipLevelAssociation(11416), sameLevelNodalMepAlreadyAssignedToVlan(11417), cfmMulticastCcmOnNodalPlsbMepNotAllowed(11422), cfmNodalMepOnlyOnPlsbVlan(11424), cfmNodalMipOnlyOnPlsbVlan(11425), cfmNodalMpOnlyOnePerVlan(11426), cfmCannotL2PingWhenLbmInProgress(11427), cfmCannotLBMWhenL2PingInProgress(11428), cfmCannotAbortWhenNoL2PingInProgress(11429), cfmL2PingMepNotOkToSetReady(11430), cfmVlanNotReadyToSetL2Ping(11431), cfmL2PingExceedMaxMessagesLimit(11432), cfmL2PingExceedMaxDataSizeLimit(11433), cfmL2PingTestPatternSizeError(11434), cfmL2PingFrameTooSmall(11435), cfmL2PingFrameSizeExceedMaxForNodalMep(11436), cfmCannotLTMWhenL2TraceInProgress(11437), cfmCannotL2TraceWhenLTMInProgress(11438), cfmCannotAbortWhenNoL2TraceInProgress(11439), cfmL2TraceMepNotOkToSetReady(11440), cfmVlanNotReadyToSetL2Trace(11441), cfmL2CmdVlanNotFound(11442), cfmL2TraceInvalidIsid(11443), cfmNodalMipOnlyOnePerVlan(11447), cfmNodalMepOnlyOnePerVlan(11448), cfmMepMustBeEnabledForCmd(11449), cfmSpbmVirtualNotSet(11450), cfmSpbmVirtualNotPrimary(11451), cfmL2IpPingIsNotOkToSetReady(11452), cfmNotReadyToSetL2IpPing(11453), cfmNotMemoryAllocatedForL2(11454), cfmL2IpTraceIsNotOkToSetReady(11455), cfmNotReadyToSetL2IpTrace(11456), cfmIpLookupRouteFailed(11457), invalidIpAddrType(11458), cfmL2IpPingEntryMustCreatedFirst(11459), cfmL2IpTraceEntryMustCreatedFirst(11460), vlanAdminStatusConfigNotAllowed(12803), configNotAllowedOnVlanInterfaces(12804), configNotAllowedMdNameUsed(12807), configNotAllowedMaNameUsed(12808), configNotAllowedCfmInUseOnVlan(12809), configNotAllowedMdNameUsedByGlobalCfm(12810), configNotAllowedMaNameUsedByGlobalCfm(12811), configNotAllowedMepUsedByGlobalCfm(12812), configCfmInternalOnVlan(12813), configCfmGlobalEnabled(12814), configCfmTracetreeNotAllowed(12815), configCfmSmltNotAllowed(12816), cfmSrcModeCannotBeNoVlanMacOnSpbmVlans(12817), cfmL2McastTraceEntryMustBeCreatedFirst(12818), cfmNotReadyToSetL2McastTrace(12819), cfmMcastLookupRouteFailed(12820), cfmCannotDeleteVlanWithCfmMsgInProgress(12821), cfmCannotChangeMepWithCfmMsgInProgress(12822), onlyGlobalCfmSupportForNonSpbmVlan(12823), readWriteAccessReadOnly(900), readWriteAccessLevelOne(901), readWriteAccessLevelTwo(902), readWriteAccessLevelThree(903), readWriteAccessReadWrite(904), readWriteAccessReadWriteAll(905), readWriteAccessUnknownLevel(906)

rcErrorSendTrap		1.3.6.1.4.1.2272.1.20.5
Indicates whether to send trap upon receiving an error in the system.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcTrapsMib		1.3.6.1.4.1.2272.1.21.0
OBJECT IDENTIFIER

rcCardDown		1.3.6.1.4.1.2272.1.21.1
A rcCardDown trap signifies that the SNMPv2 entity, acting in an agent role, has detected that the rcCardOperStatus object for one of its cards is about to transition into the down state.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnCardDown		1.3.6.1.4.1.2272.1.21.0.1
A rcCardDown trap signifies that the SNMPv2 entity, acting in an agent role, has detected that the rcCardOperStatus object for one of its cards is about to transition into the down state.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcCardUp		1.3.6.1.4.1.2272.1.21.2
A rcCardUp trap signifies that the SNMPv2 entity, acting in an agent role, has detected that the rcCardOperStatus object for one of its cards is about to transition into the up state.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnCardUp		1.3.6.1.4.1.2272.1.21.0.2
A rcCardUp trap signifies that the SNMPv2 entity, acting in an agent role, has detected that the rcCardOperStatus object for one of its cards is about to transition into the up state.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcErrorNotification		1.3.6.1.4.1.2272.1.21.3
A rcErrorNotification trap signifies that the SNMPv2 entity, acting in an agent role, has detected that an error condition has occured.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnErrorNotification		1.3.6.1.4.1.2272.1.21.0.3
A rcErrorNotification trap signifies that the SNMPv2 entity, acting in an agent role, has detected that an error condition has occured.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcStpNewRoot		1.3.6.1.4.1.2272.1.21.4
A rcStpNewRoot trap signifies that the SNMPv2 entity, acting in an agent role, has detected the Spanning Tree Protocol has declared the device to be the new root of the spanning tree.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnStpNewRoot		1.3.6.1.4.1.2272.1.21.0.4
A rcStpNewRoot trap signifies that the SNMPv2 entity, acting in an agent role, has detected the Spanning Tree Protocol has declared the device to be the new root of the spanning tree.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcStpTopologyChange		1.3.6.1.4.1.2272.1.21.5
A rcStpTopologyChange trap signifies that the SNMPv2 entity, acting in an agent role, has detected the Spanning Tree Protocol has gone due a topology change event.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnStpTopologyChange		1.3.6.1.4.1.2272.1.21.0.5
A rcStpTopologyChange trap signifies that the SNMPv2 entity, acting in an agent role, has detected the Spanning Tree Protocol has gone due a topology change event.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcChasPowerSupplyDown		1.3.6.1.4.1.2272.1.21.6
A rcChasPowerSupplyDown trap signifies that the SNMPv2 entity, acting in an agent role, has detected that the rcChasPowerSupplyOperStatus object for one of its power supply unit is about to transition into the down state.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnChasPowerSupplyDown		1.3.6.1.4.1.2272.1.21.0.6
A rcChasPowerSupplyDown trap signifies that the SNMPv2 entity, acting in an agent role, has detected that the rcChasPowerSupplyOperStatus object for one of its power supply unit is about to transition into the down state.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcChasFanDown		1.3.6.1.4.1.2272.1.21.7
A rcChasFanDown trap signifies that the SNMPv2 entity, acting in an agent role, has detected that the rcChasFanOperStatus object for one of its power supply unit is about to transition into the down state.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnChasFanDown		1.3.6.1.4.1.2272.1.21.0.7
A rcChasFanDown trap signifies that the SNMPv2 entity, acting in an agent role, has detected that the rcChasFanOperStatus object for one of its power supply unit is about to transition into the down state.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcLinkOscillation		1.3.6.1.4.1.2272.1.21.8
A rcLinkOscillation trap signifies that the SNMPv2 entity, acting in an agent role, has detected an excessive number of link state transitions on the specified port.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnLinkOscillation		1.3.6.1.4.1.2272.1.21.0.8
A rcLinkOscillation trap signifies that the SNMPv2 entity, acting in an agent role, has detected an excessive number of link state transitions on the specified port.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcMacViolation		1.3.6.1.4.1.2272.1.21.9
A rcMacViolation trap signifies that the SNMPv2 entity, acting in an agent role, has received a PDU with an invalid source MAC address.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnMacViolation		1.3.6.1.4.1.2272.1.21.0.9
A rcMacViolation trap signifies that the SNMPv2 entity, acting in an agent role, has received a PDU with an invalid source MAC address.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcSonetTrap		1.3.6.1.4.1.2272.1.21.10
A rcSonetTrap trap signifies that the SNMPv2 entity, acting in an agent role, has detected a change of status on a Sonet port.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnSonetTrap		1.3.6.1.4.1.2272.1.21.0.10
A rcSonetTrap trap signifies that the SNMPv2 entity, acting in an agent role, has detected a change of status on a Sonet port.
Status: current	Access: read-write
NOTIFICATION-TYPE

rc2kCardDown		1.3.6.1.4.1.2272.1.21.11
A rcCardDown trap signifies that the SNMPv2 entity, acting in an agent role, has detected that the rcCardOperStatus object for one of its cards is about to transition into the down state.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcn2kCardDown		1.3.6.1.4.1.2272.1.21.0.11
A rcCardDown trap signifies that the SNMPv2 entity, acting in an agent role, has detected that the rcCardOperStatus object for one of its cards is about to transition into the down state.
Status: current	Access: read-write
NOTIFICATION-TYPE

rc2kCardUp		1.3.6.1.4.1.2272.1.21.12
A rcCardUp trap signifies that the SNMPv2 entity, acting in an agent role, has detected that the rcCardOperStatus object for one of its cards is about to transition into the up state.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcn2kCardUp		1.3.6.1.4.1.2272.1.21.0.12
A rcCardUp trap signifies that the SNMPv2 entity, acting in an agent role, has detected that the rcCardOperStatus object for one of its cards is about to transition into the up state.
Status: current	Access: read-write
NOTIFICATION-TYPE

rc2kTemperature		1.3.6.1.4.1.2272.1.21.13
A rc2kTemperature trap signifies that the SNMPv2 entity, acting in an agent role, has detected the chassis is over-heating.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcn2kTemperature		1.3.6.1.4.1.2272.1.21.0.13
A rc2kTemperature trap signifies that the SNMPv2 entity, acting in an agent role, has detected the chassis is over-heating.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcChasPowerSupplyUp		1.3.6.1.4.1.2272.1.21.14
A rcChasPowerSupplyUp trap signifies that the SNMPv2 entity, acting in an agent role, has detected that the rcChasPowerSupplyOperStatus object for one of its power supply unit is about to transition into the up state.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnChasPowerSupplyUp		1.3.6.1.4.1.2272.1.21.0.14
A rcChasPowerSupplyUp trap signifies that the SNMPv2 entity, acting in an agent role, has detected that the rcChasPowerSupplyOperStatus object for one of its power supply unit is about to transition into the up state.
Status: current	Access: read-write
NOTIFICATION-TYPE

rc2kAtmPvcLinkStateChange		1.3.6.1.4.1.2272.1.21.15
A rc2kAtmPvcLinkStateChange trap signifies that the SNMPv2 entity, acting in an agent role, has detected that the rc2kAtmPvcOamVcStatus object for one of PVC is about to transition into different state, either from up to down or from down to up.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcn2kAtmPvcLinkStateChange		1.3.6.1.4.1.2272.1.21.0.15
A rc2kAtmPvcLinkStateChange trap signifies that the SNMPv2 entity, acting in an agent role, has detected that the rc2kAtmPvcOamVcStatus object for one of PVC is about to transition into different state, either from up to down or from down to up.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcStpTCN		1.3.6.1.4.1.2272.1.21.16
A rcStpTopologyChange trap signifies that the SNMPv2 entity, acting in an agent role, has detected the Spanning Tree Protocol has gone due a topology change event.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnStpTCN		1.3.6.1.4.1.2272.1.21.0.16
A rcStpTopologyChange trap signifies that the SNMPv2 entity, acting in an agent role, has detected the Spanning Tree Protocol has gone due a topology change event.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcSmltIstLinkUp		1.3.6.1.4.1.2272.1.21.17
A rcSmltIstLinkUp trap signifies that the split MLT link is from down to up.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnSmltIstLinkUp		1.3.6.1.4.1.2272.1.21.0.17
A rcSmltIstLinkUp trap signifies that the split MLT link is from down to up.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcSmltIstLinkDown		1.3.6.1.4.1.2272.1.21.18
A rcSmltIstLinkDown trap signifies that the split MLT link is from up to down.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnSmltIstLinkDown		1.3.6.1.4.1.2272.1.21.0.18
A rcSmltIstLinkDown trap signifies that the split MLT link is from up to down.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcSmltLinkUp		1.3.6.1.4.1.2272.1.21.19
A rcMltSmltId trap signifies that the split SMLT link is up.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnSmltLinkUp		1.3.6.1.4.1.2272.1.21.0.19
A rcMltSmltId trap signifies that the split SMLT link is up.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcSmltLinkDown		1.3.6.1.4.1.2272.1.21.20
A rcMltSmltId trap signifies that the split SMLT link is down.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnSmltLinkDown		1.3.6.1.4.1.2272.1.21.0.20
A rcMltSmltId trap signifies that the split SMLT link is down.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcChasFanUp		1.3.6.1.4.1.2272.1.21.21
A rcChasFanUp trap signifies that the SNMPv2 entity, acting in an agent role, has detected that the rcChasFanOperStatus object for one of its power supply unit is about to transition into the up state.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnChasFanUp		1.3.6.1.4.1.2272.1.21.0.21
A rcChasFanUp trap signifies that the SNMPv2 entity, acting in an agent role, has detected that the rcChasFanOperStatus object for one of its power supply unit is about to transition into the up state.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcPasswordChange		1.3.6.1.4.1.2272.1.21.22
A rcPasswordChange trap signifies that the SNMPv2 entity, acting in an agent role, has detected that the one of the cli password is changed.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnPasswordChange		1.3.6.1.4.1.2272.1.21.0.22
A rcPasswordChange trap signifies that the SNMPv2 entity, acting in an agent role, has detected that the one of the cli password is changed.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcEmError		1.3.6.1.4.1.2272.1.21.23
A rcEmError trap signifies that the SNMPv2 entity, acting in an agent role, has detected Em error.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnEmError		1.3.6.1.4.1.2272.1.21.0.23
A rcEmError trap signifies that the SNMPv2 entity, acting in an agent role, has detected Em error.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcPcmciaCardRemoved		1.3.6.1.4.1.2272.1.21.25
A rcPcmciaRemoved trap signifies that the SNMPv2 entity, acting in an agent role, has detected that the PCMCIA card is being removed.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnPcmciaCardRemoved		1.3.6.1.4.1.2272.1.21.0.25
A rcPcmciaRemoved trap signifies that the SNMPv2 entity, acting in an agent role, has detected that the PCMCIA card is being removed.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcSmartCpldTimerFired		1.3.6.1.4.1.2272.1.21.26
A rcSmartCpldTimerFired trap signifies that the cpld timer fired.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnSmartCpldTimerFired		1.3.6.1.4.1.2272.1.21.0.26
A rcSmartCpldTimerFired trap signifies that the cpld timer fired.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcCardCpldNotUpDate		1.3.6.1.4.1.2272.1.21.27
A rcCardCpldNotUpDate trap signifies that the cpld is not up to date.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnCardCpldNotUpDate		1.3.6.1.4.1.2272.1.21.0.27
A rcCardCpldNotUpDate trap signifies that the cpld is not up to date.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcIgapLogFileFull		1.3.6.1.4.1.2272.1.21.28
A rcIgapLogFileFull trap signifies that the Igap accounting time-out Log File reach the maximum.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnIgapLogFileFull		1.3.6.1.4.1.2272.1.21.0.28
A rcIgapLogFileFull trap signifies that the Igap accounting time-out Log File reach the maximum.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcCpLimitShutDown		1.3.6.1.4.1.2272.1.21.29
A rcCpLimitShutDown trap signifies that the cp limit for the port is shutting down.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnCpLimitShutDown		1.3.6.1.4.1.2272.1.21.0.29
A rcCpLimitShutDown trap signifies that the cp limit for the port is shutting down.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcSshServerEnabled		1.3.6.1.4.1.2272.1.21.30
A rcSshServerEnabled trap signifies that the SSH server is enabled.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnSshServerEnabled		1.3.6.1.4.1.2272.1.21.0.30
A rcSshServerEnabled trap signifies that the SSH server is enabled.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcSshServerDisabled		1.3.6.1.4.1.2272.1.21.31
A rcSshServerDisabled trap signifies that the SSH server is disabled.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnSshServerDisabled		1.3.6.1.4.1.2272.1.21.0.31
A rcSshServerDisabled trap signifies that the SSH server is disabled.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcSshSessionLogin		1.3.6.1.4.1.2272.1.21.32
A rcSshSessionLogin trap signifies that there is a SSH session login.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnSshSessionLogin		1.3.6.1.4.1.2272.1.21.0.32
A rcSshSessionLogin trap signifies that there is a SSH session login.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcSshSessionLogout		1.3.6.1.4.1.2272.1.21.33
A rcSshSessionLogout trap signifies that there is a SSH session logout.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnSshSessionLogout		1.3.6.1.4.1.2272.1.21.0.33
A rcSshSessionLogout trap signifies that there is a SSH session logout.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcSshUnauthorizedAccess		1.3.6.1.4.1.2272.1.21.34
A rcSshUnauthorizedAccess trap signifies that an unauthorized access has occured.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnSshUnauthorizedAccess		1.3.6.1.4.1.2272.1.21.0.34
A rcSshUnauthorizedAccess trap signifies that an unauthorized access has occured.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcHaCpuState		1.3.6.1.4.1.2272.1.21.35
A rcHaCpuState trap signifies that the state of the HA-CPU.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnHaCpuState		1.3.6.1.4.1.2272.1.21.0.35
A rcHaCpuState trap signifies that the state of the HA-CPU.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcInsufficientMemory		1.3.6.1.4.1.2272.1.21.36
A rcInsufficientMemory trap indicates insufficient memory on CPU blade for proper operation. Recommended memory = 256 MB available through Nortel Networks upgrade kit
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnInsufficientMemory		1.3.6.1.4.1.2272.1.21.0.36
A rcInsufficientMemory trap indicates insufficient memory on CPU blade for proper operation. Recommended memory = 256 MB available through Nortel Networks upgrade kit
Status: current	Access: read-write
NOTIFICATION-TYPE

rcSaveConfigAction		1.3.6.1.4.1.2272.1.21.37
A rcSaveConfigAction trap indicates the switch run time or boot configuration is being saved
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnSaveConfigAction		1.3.6.1.4.1.2272.1.21.0.37
A rcSaveConfigAction trap indicates the switch run time or boot configuration is being saved
Status: current	Access: read-write
NOTIFICATION-TYPE

rcLoopDetectOnPort		1.3.6.1.4.1.2272.1.21.38
A rcSaveConfigAction trap indicates that a loop has been detected on a port. The vlan on that port will be disabled.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnLoopDetectOnPort		1.3.6.1.4.1.2272.1.21.0.38
A rcLoopDetectOnPort trap indicates that a loop has been detected on a port. The vlan on that port will be disabled.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcbgpEstablished		1.3.6.1.4.1.2272.1.21.39
The BGP Established event is generated when the BGP FSM enters the ESTABLISHED state.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnbgpEstablished		1.3.6.1.4.1.2272.1.21.0.39
The BGP Established event is generated when the BGP FSM enters the ESTABLISHED state.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcbgpBackwardTransition		1.3.6.1.4.1.2272.1.21.40
The BGPBackwardTransition Event is generated when the BGP FSM moves from a higher numbered state to a lower numbered state.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnbgpBackwardTransition		1.3.6.1.4.1.2272.1.21.0.40
The BGPBackwardTransition Event is generated when the BGP FSM moves from a higher numbered state to a lower numbered state.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcAggLinkUp		1.3.6.1.4.1.2272.1.21.41
A rcAggLinkUp trap is generated when the operational state of the aggregator changes from down to up.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnAggLinkUp		1.3.6.1.4.1.2272.1.21.0.41
A rcAggLinkUp trap is generated when the operational state of the aggregator changes from down to up.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcAggLinkDown		1.3.6.1.4.1.2272.1.21.42
A rcAggLinkDown trap is generated when the operational state of the aggregator changes from up to down.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnAggLinkDown		1.3.6.1.4.1.2272.1.21.0.42
A rcAggLinkDown trap is generated when the operational state of the aggregator changes from up to down.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcIgmpNewGroupMember		1.3.6.1.4.1.2272.1.21.43
An IgmpNewGroupMember trap signifies that a new member has come on an interface.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnIgmpNewGroupMember		1.3.6.1.4.1.2272.1.21.0.43
An IgmpNewGroupMember trap signifies that a new member has come on an interface.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcIgmpLossGroupMember		1.3.6.1.4.1.2272.1.21.44
An IgmpLossGroupMember trap signifies that a group member has been lost on an interface.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnIgmpLossGroupMember		1.3.6.1.4.1.2272.1.21.0.44
An IgmpLossGroupMember trap signifies that a group member has been lost on an interface.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcIgmpNewQuerier		1.3.6.1.4.1.2272.1.21.45
An igmpNewQuerier trap signifies that a new querier has come up on an interface.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnIgmpNewQuerier		1.3.6.1.4.1.2272.1.21.0.45
An igmpNewQuerier trap signifies that a new querier has come up on an interface.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcIgmpQuerierChange		1.3.6.1.4.1.2272.1.21.46
An rcIgmpQuerierChange trap signifies that the querier has changed.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnIgmpQuerierChange		1.3.6.1.4.1.2272.1.21.0.46
An rcIgmpQuerierChange trap signifies that the querier has changed.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcDvmrpIfStateChange		1.3.6.1.4.1.2272.1.21.47
A rcDvmrpIfStateChange trap signifies that there has been a change in the state of a DVMRP interface.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnDvmrpIfStateChange		1.3.6.1.4.1.2272.1.21.0.47
A rcDvmrpIfStateChange trap signifies that there has been a change in the state of a DVMRP interface.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcDvmrpNewNbrChange		1.3.6.1.4.1.2272.1.21.48
A rcDvmrpNewNbrChange trap signifies that a new neighbor has come up on a DVMRP interface.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnDvmrpNewNbrChange		1.3.6.1.4.1.2272.1.21.0.48
A rcDvmrpNewNbrChange trap signifies that a new neighbor has come up on a DVMRP interface.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcDvmrpNbrLossChange		1.3.6.1.4.1.2272.1.21.49
A rcDvmrpNbrLossChange trap signifies that a new neighbor has gone down on a DVMRP interface.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnDvmrpNbrLossChange		1.3.6.1.4.1.2272.1.21.0.49
A rcDvmrpNbrLossChange trap signifies that a new neighbor has gone down on a DVMRP interface.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnFdbProtectViolation		1.3.6.1.4.1.2272.1.21.0.59
The rcFdbProtectViolation trap signifies that the has violated the user configured limit for total number of fdb-entries learned on that port.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnLogMsgControl		1.3.6.1.4.1.2272.1.21.0.60
A rcMsgControl trap signifies whether the number of times of repeatation of the particular Log message has exceeded the particular frequency/count or not.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnSaveConfigFile		1.3.6.1.4.1.2272.1.21.0.61
A rcSaveConfig trap signifies that either the runtime config or the boot config has been saved on the switch
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnDNSRequestResponse		1.3.6.1.4.1.2272.1.21.0.62
A rcDnsRequestResponse trap signifies that the switch had sent a query to the DNS server or it had received a successful response from the DNS Server
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnDuplicateIpAddress		1.3.6.1.4.1.2272.1.21.0.63
A rcDuplicateIpAddress trap signifies that a duplicate IP address is detected on the subnet.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnLoopDetectPortDown		1.3.6.1.4.1.2272.1.21.0.64
A rcLoopDetectPortDown trap signifies that a loop has been detected on a port and the port is going to shut down.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnLoopDetectMacDiscard		1.3.6.1.4.1.2272.1.21.0.67
A rcLoopDetectMacDiscard trap signifies that a loop has been Detected on a port and the mac address will be discarded on all ports in that vlan
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnAutoRecoverPort		1.3.6.1.4.1.2272.1.21.0.68
A rcnAutoRecoverPort trap signifies that autorecover has re-enabled a port disabled by link flap or cp limit
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnAutoRecoverLoopDetectedPort		1.3.6.1.4.1.2272.1.21.0.69
A rcnAutoRecoverPort trap signifies that autorecover has cleared the action taken on a port by loop detect
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnExtCpLimitShutDown		1.3.6.1.4.1.2272.1.21.0.70
A rcnExtCpLimitShutDown trap signifies that port is shut down due to Extended CP-Limit.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnExtCpLimitSopCongestion		1.3.6.1.4.1.2272.1.21.0.71
A rcnExtCpLimitSopCongestion signifies that system octapid polling finds that system octapid is congested or not. rcSysExtCplimitSysOctapidCongested signifies whether system octapid is congested or not. rcSysExtCplimitPortsMonitored signifies whether ports are selected for monitoring the ingress traffic utilization.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnTacacsAuthFailure		1.3.6.1.4.1.2272.1.21.0.74
TACACS+ authentication failed for user
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnTacacsNoServers		1.3.6.1.4.1.2272.1.21.0.75
Unable to use any TACACS+ servers for authentication
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnTacacsRxUnsupportedFrame		1.3.6.1.4.1.2272.1.21.0.76
Received unsupported frame from TACACS+ server
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnTacacsExceededMaxLogins		1.3.6.1.4.1.2272.1.21.0.77
Attempted to exceed the maximum number of allowed TACACS+ logins
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnTacacsClientFailure		1.3.6.1.4.1.2272.1.21.0.78
TACACS+ Client application is down
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnBpduReceived		1.3.6.1.4.1.2272.1.21.0.79
This notification will be generated when a BPDU is received on a port which has BPDU filtering enabled.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnVlacpPortDown		1.3.6.1.4.1.2272.1.21.0.80
A rcnVlacpPortDown trap signifies that Vlacp is down on the port specified.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnVlacpPortUp		1.3.6.1.4.1.2272.1.21.0.81
A rcnVlacpPortUp trap signifies that Vlacp is Up on the port specified.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnExtCpLimitShutDownNormal		1.3.6.1.4.1.2272.1.21.0.82
An rcnExtCpLimitShutDownNormal trap signifies that Ports are shut down due to Extended CP-Limit in Normal mode.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnEapMacIntrusion		1.3.6.1.4.1.2272.1.21.0.83
A rcnEapMacIntrusion trap signifies that an EAP MAC intrusion has occured on this Port.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnInterCpuCommStatus		1.3.6.1.4.1.2272.1.21.0.84
A rcnInterCpuCommStatus trap signifies the current communication status between primary and secondary CPU.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcPlugOptModTemperatureStatusTrap		1.3.6.1.4.1.2272.1.21.0.89
Used to trap changes in the temperature status
Status: current	Access: read-write
NOTIFICATION-TYPE

rcPlugOptModVoltageStatusTrap		1.3.6.1.4.1.2272.1.21.0.90
Used to trap changes in the voltage level
Status: current	Access: read-write
NOTIFICATION-TYPE

rcPlugOptModBiasStatusTrap		1.3.6.1.4.1.2272.1.21.0.91
Used to trap changes in the laser bias status
Status: current	Access: read-write
NOTIFICATION-TYPE

rcPlugOptModTxPowerStatusTrap		1.3.6.1.4.1.2272.1.21.0.92
Used to trap changes in the transmit power status
Status: current	Access: read-write
NOTIFICATION-TYPE

rcPlugOptModRxPowerStatusTrap		1.3.6.1.4.1.2272.1.21.0.93
Used to trap changes in the received power status
Status: current	Access: read-write
NOTIFICATION-TYPE

rcPlugOptModAux1StatusTrap		1.3.6.1.4.1.2272.1.21.0.94
Used to trap changes in the Aux1 status
Status: current	Access: read-write
NOTIFICATION-TYPE

rcPlugOptModAux2StatusTrap		1.3.6.1.4.1.2272.1.21.0.95
Used to trap changes in the Aux2 status
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnMaxRouteWarnClear		1.3.6.1.4.1.2272.1.21.0.110
A rcnMaxRouteWarnClear trap signifies that the number of routes in the routing table of the Virtual Router has droped below its warning threshold.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnMaxRouteWarnSet		1.3.6.1.4.1.2272.1.21.0.111
A rcnMaxRouteWarnSet trap signifies that the given Virtual Routers routing table is reaching its maximum size. Action should be taken to prevent this
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnMaxRouteDropClear		1.3.6.1.4.1.2272.1.21.0.112
A rcnMaxRouteDropClear signifies that the given Virtual Routers routing table is no longer dropping new routes as it is below its maximum size.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnMaxRouteDropSet		1.3.6.1.4.1.2272.1.21.0.113
A rcnMaxRouteDropSet trap signifies that the given Virtual Routers routing table has reached its maximum size, and is now dropping all new non static routes.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnMstpNewCistRoot		1.3.6.1.4.1.2272.1.21.0.117
A rcMstpNewCistRoottrap signifies that the SNMPv2 entity, acting in an agent role, has detected the Multiple Spanning Tree Protocol has declared the device to be the new root of the common internal spanning tree.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnMstpNewMstiRoot		1.3.6.1.4.1.2272.1.21.0.118
A rcMstpNewMstiRoot signifies that the SNMPv2 entity, acting in an agent role, has detected the Multiple Spanning Tree Protocol has declared the device to be the new root of the spanning tree instance.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnMstpNewCistRegionalRoot		1.3.6.1.4.1.2272.1.21.0.119
A rcMstpNewCistRegionalRoottrap signifies that the SNMPv2 entity, acting in an agent role, has detected the Multiple Spanning Tree Protocol has declared the device to be the new regional root of the common internal spanning tree.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnRstpNewRoot		1.3.6.1.4.1.2272.1.21.0.120
A rcRstpNewRoot signifies that the SNMPv2 entity, acting in an agent role, has detected the Rapid Spanning Tree Protocol has declared the device to be the new root of the spanning tree.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnRsmltEdgePeerModified		1.3.6.1.4.1.2272.1.21.0.124
A rcnRsmltEdgePeerModified signifies that the RSMLT Peer address is different from that of the stored address. Save config is necessary if EdgeSupport has to use this info on next reboot.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnTmuxParityError		1.3.6.1.4.1.2272.1.21.0.165
A rcnTmuxParityError trap identifies a problem in the FAD /SWIP based on the number of parity errors.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnChasPowerSupplyNoRedundancy		1.3.6.1.4.1.2272.1.21.0.167
A rcnChasPowerSupplyNoRedundancy signifies that the chassis is running on power supply without redundancy.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnChasPowerSupplyRedundancy		1.3.6.1.4.1.2272.1.21.0.168
A rcnChasPowerSupplyRedundancy signifies that the chassis is running on power supply with redundancy.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnLicenseTrialPeriodExpired		1.3.6.1.4.1.2272.1.21.0.171
A rcnLicenseTrialPeriodExpired signifies that Trial Period License has expired.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnLicenseTrialPeriodExpiry		1.3.6.1.4.1.2272.1.21.0.172
A rcnLicenseTrialPeriodExpiry signifies the time remaining before License Trial Period expires in days.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnVrfUp		1.3.6.1.4.1.2272.1.21.0.173
This notification is generated when the specified VRF's operational status is toggled from down to up.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnVrfDown		1.3.6.1.4.1.2272.1.21.0.174
This notification is generated when the specified VRF's operational status is toggled from up to down.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnMrouteIngressThresholdExceeded		1.3.6.1.4.1.2272.1.21.0.175
This notification is generated when the number of mroute ingress records exceeds the ingress threshold.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnMrouteEgressThresholdExceeded		1.3.6.1.4.1.2272.1.21.0.176
This notification is generated when the number of mroute egress records exceeds the egress threshold.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnRemoteMirroringStatus		1.3.6.1.4.1.2272.1.21.0.177
A rcRemoteMirroringStatus trap signifies whether the remote mirroring is enabled or disabled on a particular port
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnMaxMrouteWarnSet		1.3.6.1.4.1.2272.1.21.0.178
A rcnMaxMrouteWarnSet trap signifies that the given Virtual Routers multicast routing table is reaching its maximum size. Action should be taken to prevent this
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnMaxMrouteDropSet		1.3.6.1.4.1.2272.1.21.0.179
A rcnMaxMrouteDropSet trap signifies that the given Virtual Routers multicast routing table has reached its maximum size, and is now dropping all new non static routes
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnMaxMrouteWarnClear		1.3.6.1.4.1.2272.1.21.0.180
A rcnMaxMrouteWarnClear trap signifies that the number of routes in the multicast routing table of the Virtual Router has dropped below its warning threshold.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnMaxMrouteDropClear		1.3.6.1.4.1.2272.1.21.0.181
A rcnMaxMrouteDropClear trap signifies that the given Virtual Routers multicast routing table is no longer dropping new routes as it is below its maximum size.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnAggLinkStateChange		1.3.6.1.4.1.2272.1.21.0.182
The trap is generated when the operational state of the LAG changes; it identifies three events: local down, remote down, up.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnBfdSessExceedThreshold		1.3.6.1.4.1.2272.1.21.0.183
A rcnBfdSessExceedThreshold signifies that the BFD session have exceed system limit and hence creation of new session failed.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnBfdStatusChange		1.3.6.1.4.1.2272.1.21.0.184
A rcnBfdSessChange signifies that the status of BFD session changed.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnChasPowerSupplyRunningLow		1.3.6.1.4.1.2272.1.21.0.185
A rcnChasPowerSupplyRunningLow signifies that the chassis is running on low power supply.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnIsisPlsbMetricMismatchTrap		1.3.6.1.4.1.2272.1.21.0.192
A PLSB ISIS trap signifies that a LSP with a different value of l1-metric is received
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnIsisPlsbDuplicateSysidTrap		1.3.6.1.4.1.2272.1.21.0.193
A PLSB ISIS trap signifies that a Hello packet with a duplicate system-id is received
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnIsisPlsbLsdbUpdateTrap		1.3.6.1.4.1.2272.1.21.0.194
A PLSB ISIS trap signifies that LSDB information has changed
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnChasFanCoolingLow		1.3.6.1.4.1.2272.1.21.0.196
A rcnChasFanCoolingLow signifies that the chassis is running on low fan cooling.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnSmpFtpFail		1.3.6.1.4.1.2272.1.21.0.205
A rcnSmpFtpFail trap signifies that Ftp/Tftp of a logfile has failed in SMP (System Messagin Platform). Ftp of a logfile fails when configured remote server is not reachable or remote server is not configured.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnSmpLogFileDeleted		1.3.6.1.4.1.2272.1.21.0.206
A rcnSmpLogFileDeleted trap signifies that a logfile has been deleted from PCMCIA. Deletion of a logfile happens when either FTP of the logfile is successful or PCMCIA has no space to create another logfile.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnPimMaxInterfaceWarnSet		1.3.6.1.4.1.2272.1.21.0.213
A rcnPimMaxInterfaceWarnSet trap signifies that the pim interface count has exceeded the maximum set limit of 200.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnPimMaxNeighborsWarnSet		1.3.6.1.4.1.2272.1.21.0.214
A rcnPimMaxNeighborsWarnSet trap signifies that the pim neighbor count has exceeded the maximum set limit of 200.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnPimMaxPassiveInterfaceWarnSet		1.3.6.1.4.1.2272.1.21.0.215
A rcnPimMaxPassiveInterfaceWarnSet trap signifies that the pim passive interface count has exceeded the maximum set limit of 2000.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnLegacyCardDetected		1.3.6.1.4.1.2272.1.21.0.265
A rcnLegacyCardDetected trap signifies that a legacy card has been detected on the cahssis, rc2kCardIndex indicates the slot number of legacy card.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnPrFilterRspMemoryFull		1.3.6.1.4.1.2272.1.21.0.266
A rcnPrFilterRspMemoryFull trap signifies that RSP memory is full for Power Ranger filter configuration. rcPrFilterAclId indicates the ACL, on which ACL RSP memory full occurs. rc2kCardIndex indicates the slot number, on which RSP memory full event occurs.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnPrFilterStatsCntExst		1.3.6.1.4.1.2272.1.21.0.267
A rcnPrFilterStatsCntExst trap signifies that RSP filter stats counters have been run out. When this happens, affected filters won't get their counter updated by filter forwarding engine. rcPrFilterAclId indicates the ACL, on which filter stats counter exhaust occurs. rc2kCardIndex indicates the slot number, on which filter stats counter exhaust occurs.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnIsisPlsbBvidMismatchTrap		1.3.6.1.4.1.2272.1.21.0.278
A PLSB ISIS trap signifies that a Hello packet with mismatched B-VIDs is received
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnIsisPlsbSmltVirtBmacMismatchTrap		1.3.6.1.4.1.2272.1.21.0.279
A PLSB ISIS trap signifies that Virtual BMAC configured in the switch is different from virtual BMAC configured in the IST peer
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnIsisPlsbSmltPeerBmacMismatchTrap		1.3.6.1.4.1.2272.1.21.0.280
A PLSB ISIS trap signifies that either the Smlt Peer BMAC configured in the IST peer is different from the ISIS SystemId of the local switch OR The Smlt peer BMAC configured in the local switch is different from the ISIS systemId of the IST peer
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnIsisPlsbAdjStateTrap		1.3.6.1.4.1.2272.1.21.0.281
A PLSB ISIS trap signifies ISIS adjacency state change.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnIsisPlsbDuplicateNnameTrap		1.3.6.1.4.1.2272.1.21.0.282
A PLSB ISIS trap signifies that a LSP with duplicate nickname is received, this trap should be generated by all the switches in the network.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnIsisPlsbSmltSplitBebMismatchTrap		1.3.6.1.4.1.2272.1.21.0.283
A PLSB ISIS trap signifies that the Smlt Split-Beb configured in the local switch and IST peer are same. One IST switch shoule be configured as Split-Beb primary and the IST peer should be configured as Split-Beb secondary.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnIsisPlsbMultiLinkAdjTrap		1.3.6.1.4.1.2272.1.21.0.284
A PLSB ISIS trap signifies that multiple ISIS adjacencies are formed with the same ISIS node.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcnVLacpFlapDetectShutDown		1.3.6.1.4.1.2272.1.21.0.289
A rcVlacpFlapDetectShutDown trap signifies that the port is shut down because rcPortVLacpFlapFrequency number of VLACP flaps were detected within rcPortVLacpFlapInterval seconds on this port.The port can be brought UP by toggling the port admin state manually.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcSyslogGlobal		1.3.6.1.4.1.2272.1.22.1
OBJECT IDENTIFIER

rcSyslogGlobalEnable		1.3.6.1.4.1.2272.1.22.1.1
Used to enable/disable the SysLog feature. When enabled this feature will send a message to a server on a network that this configured to receive and store diagnostic messages from this device. The type of messages sent is user configurable.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcSyslogGlobalMaxHosts		1.3.6.1.4.1.2272.1.22.1.2
Maximun number of remote hosts considered 'active' and able to receive messages from the Syslog service on the router.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..10

rcSyslogGlobalOperState		1.3.6.1.4.1.2272.1.22.1.3
The operational state of the syslog service on the router.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	active(1), inactive(2), emptyHostTbl(3), allHostDisabled(4)

rcSyslogGlobalHeader		1.3.6.1.4.1.2272.1.22.1.4
The IP Header Type for the Syslog Packet.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	default(1), managementVIP(2), circuitlessIP(3)

rcSyslogHostTbl		1.3.6.1.4.1.2272.1.22.2
Table of remote host destinations for syslog.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcSyslogHostEntry

rcSyslogHostEntry		1.3.6.1.4.1.2272.1.22.2.1
Entry containing information for a particular entry in rcSyslogHostTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcSyslogHostEntry

rcSyslogHostId		1.3.6.1.4.1.2272.1.22.2.1.1
Host Id.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..10

rcSyslogHostIpAddr		1.3.6.1.4.1.2272.1.22.2.1.2
Host Ip Address
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcSyslogHostUdpPort		1.3.6.1.4.1.2272.1.22.2.1.3
Specifies the UDP port to use to send syslog messages to the host.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	514..530

rcSyslogHostFacility		1.3.6.1.4.1.2272.1.22.2.1.4
Specifies the UNIX facility used in messages to the syslog host. Default is LOCAL7.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	local0(128), local1(136), local2(144), local3(152), local4(160), local5(168), local6(176), local7(184)

rcSyslogHostModuleId		1.3.6.1.4.1.2272.1.22.2.1.5
Specifies for which modules/tasks syslog messages should be sent. Default is all modules/tasks.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	common(1), snmp(2), rmon(4), portmgr(8), chasmgr(16), bridge(32), ospf(64), hwif(128), sim(256), cpp(512), netdrv(1024), vlanmgr(2048), cli(4096), main(8192), p2ip(16384), rcip(32768), rompager(65536), acif(131072), gbip(262144), wdt(524288), tdp(1048576), mandiag(2097152), mantest(4194304), igmp(8388608), ipfil(16777216), mlt(33554432), ippolicy(67108864), ipmc(134217728), syslog(268435456)

rcSyslogHostModuleId2		1.3.6.1.4.1.2272.1.22.2.1.6
Specifies for which modules/tasks syslog messages should be sent. Default is all modules/tasks.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcSyslogHostSeverity		1.3.6.1.4.1.2272.1.22.2.1.7
Specifies the severity level for which syslog messages should be sent for the modules specifies in 'SyslogHostModule'. Value is one of multiple (logical 'OR') of the following: info(1), warning(2), error(4), mfg(8), fatal(16).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..31

rcSyslogHostMapInfoSeverity		1.3.6.1.4.1.2272.1.22.2.1.8
Specifies the syslog severity to use for Accelar INFO messages. Default is INFO.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	emergency(1), alert(2), critical(3), error(4), warning(5), notice(6), info(7), debug(8)

rcSyslogHostMapWarningSeverity		1.3.6.1.4.1.2272.1.22.2.1.9
Specifies the syslog severity to use for Accelar WARNING messages. Default is WARNING. Should be <= INFO.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	emergency(1), alert(2), critical(3), error(4), warning(5), notice(6), info(7), debug(8)

rcSyslogHostMapErrorSeverity		1.3.6.1.4.1.2272.1.22.2.1.10
Specifies the syslog severity to use for Accelar ERROR messages. Default is ERROR. Should be <= WARNING.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	emergency(1), alert(2), critical(3), error(4), warning(5), notice(6), info(7), debug(8)

rcSyslogHostMapMfgSeverity		1.3.6.1.4.1.2272.1.22.2.1.11
Specifies the syslog severity to use for Accelar Manufactoring messages. Dafault is ERROR.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	emergency(1), alert(2), critical(3), error(4), warning(5), notice(6), info(7), debug(8)

rcSyslogHostMapFatalSeverity		1.3.6.1.4.1.2272.1.22.2.1.12
Specifies the syslog severity to use for Accelar FATAL messages. Default is EMERGENCY. Should be <= ERROR.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	emergency(1), alert(2), critical(3), error(4), warning(5), notice(6), info(7), debug(8)

rcSyslogHostMapTraceMsg		1.3.6.1.4.1.2272.1.22.2.1.13
Specifies the syslog severity to use for syslog trace messages. Default is DEBUG.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	emergency(1), alert(2), critical(3), error(4), warning(5), notice(6), info(7), debug(8)

rcSyslogHostMapTrapMsg		1.3.6.1.4.1.2272.1.22.2.1.14
Specifies the UNIX severity code to use for syslog messages for SNMP traps sent to the syslog host. Default is INFO.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	emergency(1), alert(2), critical(3), error(4), warning(5), notice(6), info(7), debug(8)

rcSyslogHostLogTraceMsgs		1.3.6.1.4.1.2272.1.22.2.1.15
Indicate whether to activate the host to log the syslog trace messages.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcSyslogHostLogTrapMsgs		1.3.6.1.4.1.2272.1.22.2.1.16
Indicate whether to activate the host to log the syslog messages for SNMP traps.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcSyslogHostEnable		1.3.6.1.4.1.2272.1.22.2.1.17
Enable/Disable messages to be sent to syslog host.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcSyslogHostRowStatus		1.3.6.1.4.1.2272.1.22.2.1.18
Used to create/delete entries in the rcSyslogTable.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcDiagMirrorByPortTable		1.3.6.1.4.1.2272.1.23.1
This table is used to configure the Mirror By Port feature. This feature allows the device to forward a copy of each packet seen on a particular port to a different port.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcDiagMirrorByPortEntry

rcDiagMirrorByPortEntry		1.3.6.1.4.1.2272.1.23.1.1
Entry containing mirror by port information.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcDiagMirrorByPortEntry

rcDiagMirrorByPortId		1.3.6.1.4.1.2272.1.23.1.1.1
Entry id.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..383

rcDiagMirrorByPortMirroredPort		1.3.6.1.4.1.2272.1.23.1.1.2
Used to configure the 'mirrored' port. The port where packets are copied from.
Status: current	Access: read-write
OBJECT-TYPE
	InterfaceIndex

rcDiagMirrorByPortMirroringPort		1.3.6.1.4.1.2272.1.23.1.1.3
Used to configure the 'mirroring' port. The port where packets are copied to.
Status: current	Access: read-write
OBJECT-TYPE
	InterfaceIndex

rcDiagMirrorByPortMode		1.3.6.1.4.1.2272.1.23.1.1.4
Used to configure the 'mode' of the mirror operation. 'tx' means packets being transmitted on the 'mirrored' port will be copied. 'rx' means packets received on the 'mirrored' port will be copied. 'both' means all traffic on the 'mirrored' port will be copied. 'rxFilter' means packets received on the 'mirrored' port is copied only if it macthes filter criteria. 'txFilter' means packets being transmitted on the 'mirrorred' port is copied only if it matches filter criteria. 'bothFilter' means both ingress and egress traffic will be copied if it matches either ingress or egress filter on the 'mirrored' port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	tx(1), rx(2), both(3), rxFilter(4), txFilter(5), bothFilter(6)

rcDiagMirrorByPortEnable		1.3.6.1.4.1.2272.1.23.1.1.5
Used to enable/disable this entry.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcDiagMirrorByPortRowStatus		1.3.6.1.4.1.2272.1.23.1.1.6
Row status of this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcDiagMirrorByPortOctapidId		1.3.6.1.4.1.2272.1.23.1.1.7
Octapid Id for a port.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Integer32

rcDiagMirrorByPortPid		1.3.6.1.4.1.2272.1.23.1.1.8
Pid for a port.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcDiagMirrorRemoteMirrorVlanId		1.3.6.1.4.1.2272.1.23.1.1.9
vlan-id to which mirrored packets needs to be send for remote mirroring. If set, this vlan id is used in mirror tag of the remote mirrored packet
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..4094

rcDiagMirrorByPortMirroredPortList		1.3.6.1.4.1.2272.1.23.1.1.12
Used to configure the 'mirrored' port. The port where packets are copied from.
Status: current	Access: read-create
OBJECT-TYPE
	PortSet

rcDiagMirrorByPortMirroringPortList		1.3.6.1.4.1.2272.1.23.1.1.13
Used to configure the 'mirroring' port. The port where packets are copied from.
Status: current	Access: read-create
OBJECT-TYPE
	PortSet

rcDiagMirrorMirroringVlanId		1.3.6.1.4.1.2272.1.23.1.1.14
Destination is a VLAN.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..4094

rcDiagMirrorMirroringMltId		1.3.6.1.4.1.2272.1.23.1.1.15
Destination is a MLT.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..256

rcDiagMirrorMirroringMgId		1.3.6.1.4.1.2272.1.23.1.1.16
Contains information about the MGID allocated.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..4096

rcDiagPortConvSteeringTable		1.3.6.1.4.1.2272.1.23.2
Diag Port Conv Steering Table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcDiagPortConvSteeringEntry

rcDiagPortConvSteeringEntry		1.3.6.1.4.1.2272.1.23.2.1
Entry containing infomation of Diag Port Conv Steering.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcDiagPortConvSteeringEntry

rcDiagPortConvSteeringId		1.3.6.1.4.1.2272.1.23.2.1.1
Entry id.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

rcDiagPortConvSteeringPortOne		1.3.6.1.4.1.2272.1.23.2.1.2
IfIndex for port one
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcDiagPortConvSteeringPortTwo		1.3.6.1.4.1.2272.1.23.2.1.3
IfIndex for port two
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcDiagPortConvSteeringMode		1.3.6.1.4.1.2272.1.23.2.1.4
Used to specify the traffic flow that should be captured between ports one and two.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	oneToTwo(1), twoToOne(2), both(3)

rcDiagPortConvSteeringForwardPort		1.3.6.1.4.1.2272.1.23.2.1.5
IfIndex of the port where captured traffic should be forwarded to.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcDiagPortConvSteeringEnable		1.3.6.1.4.1.2272.1.23.2.1.6
Enable this entry.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcDiagPortConvSteeringRowStatus		1.3.6.1.4.1.2272.1.23.2.1.7
Used to create/delete entries in the rcDiagMirrorByPortTable.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcDiagMacConvSteeringTable		1.3.6.1.4.1.2272.1.23.3
Diag Mac Conv Steering Table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcDiagMacConvSteeringEntry

rcDiagMacConvSteeringEntry		1.3.6.1.4.1.2272.1.23.3.1
Entry containing infomation of Diag Mac Conv Steering.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcDiagMacConvSteeringEntry

rcDiagMacConvSteeringId		1.3.6.1.4.1.2272.1.23.3.1.1
Entry id.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcDiagMacConvSteeringSrcMac		1.3.6.1.4.1.2272.1.23.3.1.2
Source MAC address
Status: current	Access: read-write
OBJECT-TYPE
	MacAddress

rcDiagMacConvSteeringDstMac		1.3.6.1.4.1.2272.1.23.3.1.3
Destination MAC address
Status: current	Access: read-write
OBJECT-TYPE
	MacAddress

rcDiagMacConvSteeringInPort		1.3.6.1.4.1.2272.1.23.3.1.4
IfIndex of ingress port.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcDiagMacConvSteeringForwardPort		1.3.6.1.4.1.2272.1.23.3.1.5
IfIndex of the port where captured traffic should be forwarded to.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcDiagMacConvSteeringEnable		1.3.6.1.4.1.2272.1.23.3.1.6
Enable this entry.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcDiagMacConvSteeringRowStatus		1.3.6.1.4.1.2272.1.23.3.1.7
Used to create/delete entries in the rcDiagMirrorByPortTable.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcDiagSaveConfig		1.3.6.1.4.1.2272.1.23.10
Used to configure whether the various mirror feature settings should be saved and restored across system reboot.
Status: deprecated	Access: read-write
OBJECT-TYPE
	TruthValue

rcDiagMirrorByPortTblSize		1.3.6.1.4.1.2272.1.23.11
Used to indicate table size.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcDiagPortConvSteeringTblSize		1.3.6.1.4.1.2272.1.23.12
Used to indicate table size.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcDiagMacConvSteeringTblSize		1.3.6.1.4.1.2272.1.23.13
Used to indicate table size.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcDiagDiagnosticsEnable		1.3.6.1.4.1.2272.1.23.14
Used to enable/disable the mirroring feature for the entire device. This setting overrides any setting in the various mirroring tables.
Status: deprecated	Access: read-write
OBJECT-TYPE
	TruthValue

rcDiagPcap		1.3.6.1.4.1.2272.1.23.15
OBJECT IDENTIFIER

rcDiagPcapEnable		1.3.6.1.4.1.2272.1.23.15.1
To enable pcap in secondary CPU
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcDiagPcapBufferWrap		1.3.6.1.4.1.2272.1.23.15.2
To enable buffer wrap-around when buffer is full. If set, pcap will continue to capture pkts, otherwise stops pkt storing
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcDiagPcapPcmciaWrap		1.3.6.1.4.1.2272.1.23.15.3
To wrap around the PCMCIA when saving data in PCMCIA
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcDiagPcapFrameSize		1.3.6.1.4.1.2272.1.23.15.4
Number of bytes of pkts needs to be stored
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	64..9600

rcDiagPcapBufferSize		1.3.6.1.4.1.2272.1.23.15.5
memory to be allocated for capturing the pkt
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	2..420

rcDiagPcapAutoSave		1.3.6.1.4.1.2272.1.23.15.6
To save data automatically when buffer is full
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcDiagPcapAutoSaveFileName		1.3.6.1.4.1.2272.1.23.15.7
Name of the file in which the pkt is to be stored
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..40)

rcDiagPcapAutoSaveDevice		1.3.6.1.4.1.2272.1.23.15.8
Where to store the captured pkts. If the option is network, the user need to enter an IP address also
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	pcmcia(0), network(1)

rcDiagPcapAutoSaveNetworkIpAddress		1.3.6.1.4.1.2272.1.23.15.9
ip address of the remote host where the data needs to be stored. This field is valid only if the device is network
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcDiagPcapFilterTableSize		1.3.6.1.4.1.2272.1.23.15.10
Used to indicate the number of entries in the Filter table
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcDiagPcapFilterTable		1.3.6.1.4.1.2272.1.23.15.11
A table used to store pcap secondary filters
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcDiagPcapFilterEntry

rcDiagPcapFilterEntry		1.3.6.1.4.1.2272.1.23.15.11.1
Pcap secondary filter desc
Status: current	Access: not-accessible
OBJECT-TYPE
	RcDiagPcapFilterEntry

rcDiagPcapFilterId		1.3.6.1.4.1.2272.1.23.15.11.1.1
Unique ID that represents the filter
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1000

rcDiagPcapFilterEnable		1.3.6.1.4.1.2272.1.23.15.11.1.2
Filter is enabled or not
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcDiagPcapFilterAction		1.3.6.1.4.1.2272.1.23.15.11.1.3
Action to be takesn when policy is matched
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	drop(0), capture(1), trigger-on(2), trigger-off(3)

rcDiagPcapFilterSrcMac		1.3.6.1.4.1.2272.1.23.15.11.1.4
Soruce mac address to match
Status: current	Access: read-write
OBJECT-TYPE
	MacAddress

rcDiagPcapFilterSrcMask		1.3.6.1.4.1.2272.1.23.15.11.1.5
Soruce mac address mask. Used to specify a range
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..6

rcDiagPcapFilterIsInverseSrcMac		1.3.6.1.4.1.2272.1.23.15.11.1.6
Soruce mac address Inverse. when set the mac addresses otherthan specified is matched
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcDiagPcapFilterDstMac		1.3.6.1.4.1.2272.1.23.15.11.1.7
Destination mac address
Status: current	Access: read-write
OBJECT-TYPE
	MacAddress

rcDiagPcapFilterDstMask		1.3.6.1.4.1.2272.1.23.15.11.1.8
Destination mac address mask. Used to specify a range
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..6

rcDiagPcapFilterIsInverseDstMac		1.3.6.1.4.1.2272.1.23.15.11.1.9
Destination mac address Inverse. when set the mac addresses otherthan specified is matched
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcDiagPcapFilterVlanId		1.3.6.1.4.1.2272.1.23.15.11.1.10
Vlan-id of the packet to be matched
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..4092

rcDiagPcapFilterToVlanId		1.3.6.1.4.1.2272.1.23.15.11.1.11
To Vlan-id. Used to specify a range
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..4092

rcDiagPcapFilterIsInverseVlanId		1.3.6.1.4.1.2272.1.23.15.11.1.12
Vlan-Id Inverse. when set the Vlan-Id otherthan specified range is matched
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcDiagPcapFilterPbit		1.3.6.1.4.1.2272.1.23.15.11.1.13
pBit of the packet to be matched
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..7

rcDiagPcapFilterToPbit		1.3.6.1.4.1.2272.1.23.15.11.1.14
To pBit. Used to specify a range
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..7

rcDiagPcapFilterIsInversePbit		1.3.6.1.4.1.2272.1.23.15.11.1.15
pBit Inverse. when set the pBit otherthan specified range is matched
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcDiagPcapFilterEtherType		1.3.6.1.4.1.2272.1.23.15.11.1.16
EtherType of the packet to be matched
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

rcDiagPcapFilterToEtherType		1.3.6.1.4.1.2272.1.23.15.11.1.17
To EtherType. Used to specify a range
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

rcDiagPcapFilterIsInverseEtherType		1.3.6.1.4.1.2272.1.23.15.11.1.18
EtherType Inverse. when set the EtherType otherthan specified range is matched
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcDiagPcapFilterProtocolType		1.3.6.1.4.1.2272.1.23.15.11.1.19
ProtocolType of the packet to be matched
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

rcDiagPcapFilterToProtocolType		1.3.6.1.4.1.2272.1.23.15.11.1.20
To ProtocolType. Used to specify a range
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

rcDiagPcapFilterIsInverseProtocolType		1.3.6.1.4.1.2272.1.23.15.11.1.21
ProtocolType Inverse. when set the ProtocolType otherthan specified range is matched
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcDiagPcapFilterSrcIp		1.3.6.1.4.1.2272.1.23.15.11.1.22
Source IP address of the packet to be matched
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcDiagPcapFilterToSrcIp		1.3.6.1.4.1.2272.1.23.15.11.1.23
To Source IP address. Used to specify a range
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcDiagPcapFilterIsInverseSrcIp		1.3.6.1.4.1.2272.1.23.15.11.1.24
Source IP address Inverse. when set the source IP otherthan specified range is matched
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcDiagPcapFilterDstIp		1.3.6.1.4.1.2272.1.23.15.11.1.25
Destination IP address of the packet to be matched
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcDiagPcapFilterToDstIp		1.3.6.1.4.1.2272.1.23.15.11.1.26
To Destination IP address. Used to specify a range
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcDiagPcapFilterIsInverseDstIp		1.3.6.1.4.1.2272.1.23.15.11.1.27
Destination IP address Inverse. when set the Destination IP otherthan specified is range matched
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcDiagPcapFilterDscp		1.3.6.1.4.1.2272.1.23.15.11.1.28
DSCP value of the packet to be matched
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..63

rcDiagPcapFilterToDscp		1.3.6.1.4.1.2272.1.23.15.11.1.29
To DSCP. Used to specify a range
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..63

rcDiagPcapFilterIsInverseDscp		1.3.6.1.4.1.2272.1.23.15.11.1.30
DSCP Inverse. when set the DSCP otherthan specified range is matched
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcDiagPcapFilterRowStatus		1.3.6.1.4.1.2272.1.23.15.11.1.31
Row Status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcDiagPcapFilterDscpMatchZero		1.3.6.1.4.1.2272.1.23.15.11.1.32
When this value is set to true, then 0 value of Pbit is not taken as disable value. The user will be allowed to capture packets with Pbit value of 0 also. Be default it would be set to FALSE
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcDiagPcapFilterPbitMatchZero		1.3.6.1.4.1.2272.1.23.15.11.1.33
When this value is set to true, then 0 value of Pbit is not taken as disable value. The user will be allowed to capture packets with Pbit value of 0 also. Be default it would be set to FALSE
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcDiagPcapAdvancedFilterTableSize		1.3.6.1.4.1.2272.1.23.15.12
Used to indicate the number of entries in the Filter table advanced parameter
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcDiagPcapAdvancedFilterTable		1.3.6.1.4.1.2272.1.23.15.13
A table used to store pcap secondary filters
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcDiagPcapAdvancedFilterEntry

rcDiagPcapCopyFileName		1.3.6.1.4.1.2272.1.23.15.14
Used to indicate the file name. When set, the PCAP data from PCAP engine RAM is stored into this file in PCAP engine
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rcDiagPcapResetStat		1.3.6.1.4.1.2272.1.23.15.15
To Reset PCAP statistics
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), resetStat(2)

rcDiagPcapStatPacketCapacityCount		1.3.6.1.4.1.2272.1.23.15.16
Packet Capacity Count
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

rcDiagPcapStatNumberOfPacketsReceived		1.3.6.1.4.1.2272.1.23.15.17
Number of packets received in PCAP engine
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

rcDiagPcapStatNumberOfPacketsAccumulated		1.3.6.1.4.1.2272.1.23.15.18
Number of packets captured in PCAP engine
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

rcDiagPcapStatNumberOfPacketsDroppedInPcapEngine		1.3.6.1.4.1.2272.1.23.15.19
Number of packets dropped in PCAP engine by filters
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

rcDiagPcapStatNumberOfPacketsDroppedInHardware		1.3.6.1.4.1.2272.1.23.15.20
Number of packets dropped in Hardware
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

rcDiagPcapDataValid		1.3.6.1.4.1.2272.1.23.15.21
A true/false value that indicate the return data whether is valid.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcDiagPcapEtherTypeForSvlanLevel		1.3.6.1.4.1.2272.1.23.15.22
EtherType of svlan level.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	5dd..ffff

rcDiagPcapAdvancedFilterEntry		1.3.6.1.4.1.2272.1.23.15.13.1
Pcap secondary Advanced filter desc
Status: current	Access: not-accessible
OBJECT-TYPE
	RcDiagPcapAdvancedFilterEntry

rcDiagPcapAdvancedFilterId		1.3.6.1.4.1.2272.1.23.15.13.1.1
Unique ID that represents the filter
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1000

rcDiagPcapAdvancedFilterUdpPort		1.3.6.1.4.1.2272.1.23.15.13.1.2
UdpPort of the packet to be matched
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

rcDiagPcapAdvancedFilterToUdpPort		1.3.6.1.4.1.2272.1.23.15.13.1.3
To UdpPort. Used to specify a range
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

rcDiagPcapAdvancedFilterIsInverseUdpPort		1.3.6.1.4.1.2272.1.23.15.13.1.4
UdpPort Inverse. when set the UdpPort otherthan specified range is matched
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcDiagPcapAdvancedFilterTcpPort		1.3.6.1.4.1.2272.1.23.15.13.1.5
TcpPort of the packet to be matched
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

rcDiagPcapAdvancedFilterToTcpPort		1.3.6.1.4.1.2272.1.23.15.13.1.6
To TcpPort. Used to specify a range
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

rcDiagPcapAdvancedFilterIsInverseTcpPort		1.3.6.1.4.1.2272.1.23.15.13.1.7
TcpPort Inverse. when set the TcpPort otherthan specified range is matched
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcDiagPcapAdvancedFilterUserDefinedData		1.3.6.1.4.1.2272.1.23.15.13.1.8
User defined data to match with the packets received
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rcDiagPcapAdvancedFilterUserDefinedDataSize		1.3.6.1.4.1.2272.1.23.15.13.1.9
Length of user defined data
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..50

rcDiagPcapAdvancedFilterUserDefinedOffset		1.3.6.1.4.1.2272.1.23.15.13.1.10
Offset from which match has to start
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..9600

rcDiagPcapAdvancedFilterIsInverseUserDefined		1.3.6.1.4.1.2272.1.23.15.13.1.11
TcpPort Inverse. when set the Userdata otherthan specified is matched
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcDiagPcapAdvancedFilterTimer		1.3.6.1.4.1.2272.1.23.15.13.1.12
Timer to start the pcap capture window in ms
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..3600000

rcDiagPcapAdvancedFilterPacketCount		1.3.6.1.4.1.2272.1.23.15.13.1.13
Number of packets to be captured before disabling pcap
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

rcDiagPcapAdvancedFilterRefreshTimer		1.3.6.1.4.1.2272.1.23.15.13.1.14
Refresh timer in ms
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..3600000

rcDiagPcapAdvancedFilterRowStatus		1.3.6.1.4.1.2272.1.23.15.13.1.15
RowStatus
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpxRoutingEnable		1.3.6.1.4.1.2272.1.24.1
Global Ipx Routing control variable
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpxAddrTable		1.3.6.1.4.1.2272.1.24.2
The table of addressing information relevant to this entity's IPX addresses. This table is used for associating IfIndex and IPX network number.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpxAddrEntry

rcIpxAddrEntry		1.3.6.1.4.1.2272.1.24.2.1
The addressing information for one of this entity's IP addresses.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpxAddrEntry

rcIpxAddrVlanId		1.3.6.1.4.1.2272.1.24.2.1.1
The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..4094

rcIpxAddrNetAddr		1.3.6.1.4.1.2272.1.24.2.1.2
IPX Network address.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(4)

rcIpxAddrEncap		1.3.6.1.4.1.2272.1.24.2.1.3
Specify IPX encapsulation format. It is relevent if the VLAN is port based. But it's always nice to have it.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), ethernetii(1), snap(2), llc(3), raw(4)

rcIpxAddrEntryStatus		1.3.6.1.4.1.2272.1.24.2.1.4
Used to create/delete entries in the rcIpxAddrEntry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpxAddrTicks		1.3.6.1.4.1.2272.1.24.2.1.5
The tick value gets updated to the routing table when an ipx address is being assigned to a vlan.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..2147483647

rcIpxPolicyNetTableSize		1.3.6.1.4.1.2272.1.24.3
Used to indicate the number of entries in the table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpxPolicyNetTable		1.3.6.1.4.1.2272.1.24.4
Net Table is used to store the IPX network address range. This entry is used for Net List Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpxPolicyNetEntry

rcIpxPolicyNetEntry		1.3.6.1.4.1.2272.1.24.4.1
table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpxPolicyNetEntry

rcIpxPolicyNetId		1.3.6.1.4.1.2272.1.24.4.1.1
Unique ID to represent the entry in the table.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..2147483647

rcIpxPolicyNetFromNet		1.3.6.1.4.1.2272.1.24.4.1.2
IPX Network Address.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(4)

rcIpxPolicyNetToNet		1.3.6.1.4.1.2272.1.24.4.1.3
This is used to specify a range of IPX network addresses. This is an optional parameter. The default value is NetAddr. In that case the entry refers to a single IPX network.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(4)

rcIpxPolicyNetName		1.3.6.1.4.1.2272.1.24.4.1.4
Unique Name to represent the entry in the table. Id & Name have one-to-one relationship.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..15)

rcIpxPolicyNetRowStatus		1.3.6.1.4.1.2272.1.24.4.1.5
.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpxPolicyServTableSize		1.3.6.1.4.1.2272.1.24.5
Used to indicate the number of entries in the table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpxPolicyServTable		1.3.6.1.4.1.2272.1.24.6
Service Table is used to store Service Type and Service Name. This is used only for SAP Updates.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpxPolicyServEntry

rcIpxPolicyServEntry		1.3.6.1.4.1.2272.1.24.6.1
table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpxPolicyServEntry

rcIpxPolicyServId		1.3.6.1.4.1.2272.1.24.6.1.1
Used to store the service Id.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpxPolicyServServiceType		1.3.6.1.4.1.2272.1.24.6.1.2
Used to store the service type.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

rcIpxPolicyServServiceName		1.3.6.1.4.1.2272.1.24.6.1.3
Used to store the service Name. This is an optional parameter. If not entered, '*' is taken as default value. This is matched to any service name. Also, '*' can be used to match wildcard characters. This is supported only at the end of the service name. For Eg: Printer* will be matched to Printer1, Printer2, Printer123 etc. Service Name matching is CASE SENSITIVE
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..47)

rcIpxPolicyServName		1.3.6.1.4.1.2272.1.24.6.1.4
Used to store the entry name. Id & Name have one-to-one relationship.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..15)

rcIpxPolicyServRowStatus		1.3.6.1.4.1.2272.1.24.6.1.5
.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpxPolicyListTableSize		1.3.6.1.4.1.2272.1.24.7
Used to indicate the number of entries in the table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpxPolicyListTable		1.3.6.1.4.1.2272.1.24.8
PolicyList Table is used to store generic policies that can be used by both RIP and SAP as their in/out policies.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpxPolicyListEntry

rcIpxPolicyListEntry		1.3.6.1.4.1.2272.1.24.8.1
table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpxPolicyListEntry

rcIpxPolicyListId		1.3.6.1.4.1.2272.1.24.8.1.1
Index used to uniquely Identify a group of policies in the route policy table.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

rcIpxPolicyListSeqnum		1.3.6.1.4.1.2272.1.24.8.1.2
Second Index used to identify a specific policy with in the route policy group (grouped by Id). This field allows users to specify different MATCH, SET parameters and an action. Also used to resolve the tie between 2 matching policies. The policy with lower sequence number is used.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

rcIpxPolicyListName		1.3.6.1.4.1.2272.1.24.8.1.3
Is used to group a set of policies with different sequence number. Id & Name have one-to-one relationship Different policy groups can have same sequence number, whereas with in a group the sequence must be different.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..15)

rcIpxPolicyListEnable		1.3.6.1.4.1.2272.1.24.8.1.4
value specified here indicates whether the policy is enabled or not. If disabled, the policy should not be used.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpxPolicyListAction		1.3.6.1.4.1.2272.1.24.8.1.5
This determines what to do with the RIP/SAP packet. If the value is 'permit', then only in or out the packet. Otherwise, drop the packet.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	permit(1), deny(2)

rcIpxPolicyListRouteSource		1.3.6.1.4.1.2272.1.24.8.1.6
Used to specify the Route Source of the route Packet. This field is used only for announce policies. For accept policies, this field is ignored. Value is one of multiple (logical 'OR') of following values: direct(1), nlsp(2), rip(4), static(8), any(15)
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..15

rcIpxPolicyListMatchNetList		1.3.6.1.4.1.2272.1.24.8.1.7
List of networks to which this policy is applied. The Network List Name is entered. When this is not referring to any list or the Net List Table to which it is pointing to is empty, then THIS POLICY MATCHES ALL NETWORK ADDRESSES.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rcIpxPolicyListMatchServList		1.3.6.1.4.1.2272.1.24.8.1.8
List of service types and Service Names to which this policy is applied. The Service List name is entered. This field is used only for SAP out/in policies. For, RIP policies, this field is discarded. When this is not referring to any list or the Service List Table to which it is pointing to is empty, then this POLICY MATCHES ALL SERVICE TYPE AND SERVICE NAME.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rcIpxPolicyListHops		1.3.6.1.4.1.2272.1.24.8.1.9
This value is used as Hop count for out policies. If this field is 0, then Hop count is not modified. The default value is '0'. This field is also applicable only for Out Policies.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..16

rcIpxPolicyListTicks		1.3.6.1.4.1.2272.1.24.8.1.10
The tick value which will be updated for RIP when the routing method is tick.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..2147483647

rcIpxPolicyListRowStatus		1.3.6.1.4.1.2272.1.24.8.1.11
.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpxRipOutFilterTableSize		1.3.6.1.4.1.2272.1.24.9
Used to indicate the number of entries in the table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpxRipOutFilterTable		1.3.6.1.4.1.2272.1.24.10
RipOutFilter Table is used to store generic policies that can be used by both RIP and SAP as their in/out policies.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpxRipOutFilterEntry

rcIpxRipOutFilterEntry		1.3.6.1.4.1.2272.1.24.10.1
table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpxRipOutFilterEntry

rcIpxRipOutFilterInterface		1.3.6.1.4.1.2272.1.24.10.1.1
IPX Network address. The interface to which the policy is applied.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(4)

rcIpxRipOutFilterPolicyName		1.3.6.1.4.1.2272.1.24.10.1.2
The name of the policy group to which this entry refers.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rcIpxRipOutFilterRowStatus		1.3.6.1.4.1.2272.1.24.10.1.3
.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpxSapOutFilterTableSize		1.3.6.1.4.1.2272.1.24.11
Used to indicate the number of entries in the table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpxSapOutFilterTable		1.3.6.1.4.1.2272.1.24.12
SapOutFilter Table is used to store generic policies that can be used by both RIP and SAP as their in/out policies.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpxSapOutFilterEntry

rcIpxSapOutFilterEntry		1.3.6.1.4.1.2272.1.24.12.1
table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpxSapOutFilterEntry

rcIpxSapOutFilterInterface		1.3.6.1.4.1.2272.1.24.12.1.1
IPX Network address. The interface to which the policy is applied.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(4)

rcIpxSapOutFilterPolicyName		1.3.6.1.4.1.2272.1.24.12.1.2
The name of the policy group to which this entry refers.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rcIpxSapOutFilterRowStatus		1.3.6.1.4.1.2272.1.24.12.1.3
.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpxRipInFilterTableSize		1.3.6.1.4.1.2272.1.24.13
Used to indicate the number of entries in the table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpxRipInFilterTable		1.3.6.1.4.1.2272.1.24.14
RipInFilter Table is used to store generic policies that can be used by both RIP and SAP as their in/out policies.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpxRipInFilterEntry

rcIpxRipInFilterEntry		1.3.6.1.4.1.2272.1.24.14.1
table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpxRipInFilterEntry

rcIpxRipInFilterInterface		1.3.6.1.4.1.2272.1.24.14.1.1
IPX Network address. The interface to which the policy is applied.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(4)

rcIpxRipInFilterPolicyName		1.3.6.1.4.1.2272.1.24.14.1.2
The name of the policy group to which this entry refers.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rcIpxRipInFilterRowStatus		1.3.6.1.4.1.2272.1.24.14.1.3
.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpxSapInFilterTableSize		1.3.6.1.4.1.2272.1.24.15
Used to indicate the number of entries in the table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpxSapInFilterTable		1.3.6.1.4.1.2272.1.24.16
SapInFilter Table is used to store generic policies that can be used by both RIP and SAP as their in/out policies.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpxSapInFilterEntry

rcIpxSapInFilterEntry		1.3.6.1.4.1.2272.1.24.16.1
table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpxSapInFilterEntry

rcIpxSapInFilterInterface		1.3.6.1.4.1.2272.1.24.16.1.1
IPX Network address. The interface to which the policy is applied.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(4)

rcIpxSapInFilterPolicyName		1.3.6.1.4.1.2272.1.24.16.1.2
The name of the policy group to which this entry refers.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rcIpxSapInFilterRowStatus		1.3.6.1.4.1.2272.1.24.16.1.3
.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpxRoutingMethod		1.3.6.1.4.1.2272.1.24.17
This global variable is referenced each time a decision has to be taken
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ticks(1), hops(2)

rcIpxSapInterfaceTable		1.3.6.1.4.1.2272.1.24.18
SapInterface Table is used to store generic policies that can be used by SAP as their in/out policies.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpxSapInterfaceEntry

rcIpxSapInterfaceEntry		1.3.6.1.4.1.2272.1.24.18.1
table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpxSapInterfaceEntry

rcIpxSapInterfaceNetNum		1.3.6.1.4.1.2272.1.24.18.1.1
IPX Network address. The interface to which the policy is applied.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(4)

rcIpxSapInterfaceInPolicy		1.3.6.1.4.1.2272.1.24.18.1.2
The name of the in filter group to which this entry refers.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rcIpxSapInterfaceOutPolicy		1.3.6.1.4.1.2272.1.24.18.1.3
The name of the out filter to which this entry refers.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rcIpxRipInterfaceTable		1.3.6.1.4.1.2272.1.24.19
RipInterface Table is used to store generic policies that can be used by RIP as their in/out policies.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpxRipInterfaceEntry

rcIpxRipInterfaceEntry		1.3.6.1.4.1.2272.1.24.19.1
table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpxRipInterfaceEntry

rcIpxRipInterfaceNetNum		1.3.6.1.4.1.2272.1.24.19.1.1
IPX Network address. The interface to which the policy is applied.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(4)

rcIpxRipInterfaceInPolicy		1.3.6.1.4.1.2272.1.24.19.1.2
The name of the in filter group to which this entry refers.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rcIpxRipInterfaceOutPolicy		1.3.6.1.4.1.2272.1.24.19.1.3
The name of the out filter to which this entry refers.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rcIpxBrouterTable		1.3.6.1.4.1.2272.1.24.20
The table of addressing information relevant to this entity's IPX addresses. This table is used for associating IfIndex and IPX network number.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpxBrouterEntry

rcIpxBrouterEntry		1.3.6.1.4.1.2272.1.24.20.1
The addressing information for one of this entity's IP addresses.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpxBrouterEntry

rcIpxBrouterPortIndex		1.3.6.1.4.1.2272.1.24.20.1.1
The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

rcIpxBrouterVlanId		1.3.6.1.4.1.2272.1.24.20.1.2
The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the sam2 value of ifIndex.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4094

rcIpxBrouterNetAddr		1.3.6.1.4.1.2272.1.24.20.1.3
IPX Network address.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(4)

rcIpxBrouterEncap		1.3.6.1.4.1.2272.1.24.20.1.4
Specify IPX encapsulation format. It is relevent if the VLAN is port based. But it's always nice to have it.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(0), ethernetii(1), snap(2), llc(3), raw(4)

rcIpxBrouterMacOffset		1.3.6.1.4.1.2272.1.24.20.1.5
IPX Network address.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..507

rcIpxBrouterTicks		1.3.6.1.4.1.2272.1.24.20.1.6
The tick value gets updated to the routing table when an ipx address is being assigned to a vlan.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..2147483647

rcIpxBrouterRowStatus		1.3.6.1.4.1.2272.1.24.20.1.7
Used to create/delete entries in the rcIpxBrouterEntry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpxRsmlt		1.3.6.1.4.1.2272.1.24.21
OBJECT IDENTIFIER

rcIpxRsmltGlobal		1.3.6.1.4.1.2272.1.24.21.1
OBJECT IDENTIFIER

rcIpxRsmltGlobalTableSize		1.3.6.1.4.1.2272.1.24.21.1.1
Route Smlt table size.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpxRsmltOperTable		1.3.6.1.4.1.2272.1.24.21.2
Route Smlt Table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpxRsmltOperEntry

rcIpxRsmltOperEntry		1.3.6.1.4.1.2272.1.24.21.2.1
An entry of Ip As Path Access List Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpxRsmltOperEntry

rcIpxRsmltOperVlanId		1.3.6.1.4.1.2272.1.24.21.2.1.1
Vlan id.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4093

rcIpxRsmltOperIfIndex		1.3.6.1.4.1.2272.1.24.21.2.1.2
Route Smlt Oper IfIndex.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcIpxRsmltOperAdminStatus		1.3.6.1.4.1.2272.1.24.21.2.1.3
is a enable/disable flag.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIpxRsmltOperHoldDownTimer		1.3.6.1.4.1.2272.1.24.21.2.1.4
Timer value, the range of value is from 0 to 3600.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..3600

rcIpxRsmltOperHoldDownTimeRemaining		1.3.6.1.4.1.2272.1.24.21.2.1.5
The time value that indicate how much time remaining of HoldDownTimer.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..3600

rcIpxRsmltOperHoldUpTimer		1.3.6.1.4.1.2272.1.24.21.2.1.6
The range of value 0 to 3600 or 9999. 9999 means infinity.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..3600 | 9999

rcIpxRsmltOperHoldUpTimeRemaining		1.3.6.1.4.1.2272.1.24.21.2.1.7
The time value that indicate how much time remaining of HoldUpTimer.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..3600 | 9999

rcIpxRsmltOperOperStatus		1.3.6.1.4.1.2272.1.24.21.2.1.8
The operation status of Rsmlt, up or down.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2)

rcIpxRsmltOperSmltId		1.3.6.1.4.1.2272.1.24.21.2.1.9
The id range for SMLT is 1-32.
Status: current	Access: read-only
OBJECT-TYPE
	IdList

rcIpxRsmltOperSltId		1.3.6.1.4.1.2272.1.24.21.2.1.10
The id range for SLT is 1-512.
Status: current	Access: read-only
OBJECT-TYPE
	IdList

rcIpxRsmltOperRowStatus		1.3.6.1.4.1.2272.1.24.21.2.1.11
Row Status.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIpxRsmltOperMacAddr		1.3.6.1.4.1.2272.1.24.21.2.1.12
Mac Address.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rcIpxRsmltPeerTable		1.3.6.1.4.1.2272.1.24.21.3
Route Smlt Table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpxRsmltPeerEntry

rcIpxRsmltPeerEntry		1.3.6.1.4.1.2272.1.24.21.3.1
An entry of Ip As Path Access List Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpxRsmltPeerEntry

rcIpxRsmltPeerVlanId		1.3.6.1.4.1.2272.1.24.21.3.1.1
Vlan id.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4093

rcIpxRsmltPeerIfIndex		1.3.6.1.4.1.2272.1.24.21.3.1.2
Route Smlt Oper IfIndex.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcIpxRsmltPeerAdminStatus		1.3.6.1.4.1.2272.1.24.21.3.1.3
is a enable/disable flag.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcIpxRsmltPeerHoldDownTimer		1.3.6.1.4.1.2272.1.24.21.3.1.4
Timer value, the range of value is from 0 to 3600.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..3600

rcIpxRsmltPeerHoldDownTimeRemaining		1.3.6.1.4.1.2272.1.24.21.3.1.5
The time value that indicate how much time remaining of HoldDownTimer.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..3600

rcIpxRsmltPeerHoldUpTimer		1.3.6.1.4.1.2272.1.24.21.3.1.6
The range of value 0 to 3600 or 9999. 9999 means infinity.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..3600 | 9999

rcIpxRsmltPeerHoldUpTimeRemaining		1.3.6.1.4.1.2272.1.24.21.3.1.7
The time value that indicate how much time remaining of HoldUpTimer.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..3600 | 9999

rcIpxRsmltPeerOperStatus		1.3.6.1.4.1.2272.1.24.21.3.1.8
The operation status of Rsmlt, up or down.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2)

rcIpxRsmltPeerSmltId		1.3.6.1.4.1.2272.1.24.21.3.1.9
The id range for SMLT is 1-32.
Status: current	Access: read-only
OBJECT-TYPE
	IdList

rcIpxRsmltPeerSltId		1.3.6.1.4.1.2272.1.24.21.3.1.10
The id range for SLT is 1-512.
Status: current	Access: read-only
OBJECT-TYPE
	IdList

rcIpxRsmltPeerMacAddr		1.3.6.1.4.1.2272.1.24.21.3.1.11
Mac Address.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rcIpxRipGlobal		1.3.6.1.4.1.2272.1.24.22
OBJECT IDENTIFIER

rcIpxRipGlobalPace		1.3.6.1.4.1.2272.1.24.22.1
The maximum pace, in packets per second, at which RIP packets may be sent on this circuit.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcIpxRipGlobalUpdate		1.3.6.1.4.1.2272.1.24.22.2
The RIP periodic update interval, in seconds.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcIpxRipGlobalAgeMultiplier		1.3.6.1.4.1.2272.1.24.22.3
The holding multiplier for information received in RIP periodic updates.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcPosPppIpxTable		1.3.6.1.4.1.2272.1.26.1
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPosPppIpxEntry

rcPosPppIpxEntry		1.3.6.1.4.1.2272.1.26.1.1
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPosPppIpxEntry

rcPosPppIpxIfIndex		1.3.6.1.4.1.2272.1.26.1.1.1
port number.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcPosPppIpxIpxcpAdminStatus		1.3.6.1.4.1.2272.1.26.1.1.2
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	open(1), close(2)

rcPosPppIpxOperStatus		1.3.6.1.4.1.2272.1.26.1.1.3
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2), unknown(3)

rcPosPppIpxNetAddr		1.3.6.1.4.1.2272.1.26.1.1.4
IPX Network address.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(4)

rcPosPppIpxRoutingProtocol		1.3.6.1.4.1.2272.1.26.1.1.5
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), rip(2)

rcPosSonetTable		1.3.6.1.4.1.2272.1.26.2
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPosSonetEntry

rcPosSonetEntry		1.3.6.1.4.1.2272.1.26.2.1
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPosSonetEntry

rcPosSonetIndex		1.3.6.1.4.1.2272.1.26.2.1.1
pos ifIndex.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcPosSonetFraming		1.3.6.1.4.1.2272.1.26.2.1.2
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	sonet(1), sdh(2)

rcPosSonetSectionTrace		1.3.6.1.4.1.2272.1.26.2.1.3
config. J0 byte
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..255

rcPosSonetSectionGrowth		1.3.6.1.4.1.2272.1.26.2.1.4
config. Z0 byte
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..255

rcPosSonetSyncronization		1.3.6.1.4.1.2272.1.26.2.1.5
config. S1 byte
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..255

rcPosSonetStsPathTrace		1.3.6.1.4.1.2272.1.26.2.1.6
config. 64/16 byte.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(64)

rcPosSonetPathSignalLabel		1.3.6.1.4.1.2272.1.26.2.1.7
config. C2 byte
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..255

rcPosSonetClockSource		1.3.6.1.4.1.2272.1.26.2.1.8
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	line(1), internal(2)

rcPosSonetScramble		1.3.6.1.4.1.2272.1.26.2.1.9
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcPosSonetOperStatusFraming		1.3.6.1.4.1.2272.1.26.2.1.10
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPosSonetOperStatusClockSource		1.3.6.1.4.1.2272.1.26.2.1.11
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPosSonetOperStatusScramble		1.3.6.1.4.1.2272.1.26.2.1.12
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	EnableValue

rcPosSonetOperStatusSectionTrace		1.3.6.1.4.1.2272.1.26.2.1.13
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPosSonetOperStatusPathSignalLabel		1.3.6.1.4.1.2272.1.26.2.1.14
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPosLineStatusTable		1.3.6.1.4.1.2272.1.26.3
Pos Line Status Table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPosLineStatusEntry

rcPosLineStatusEntry		1.3.6.1.4.1.2272.1.26.3.1
Entry containing infomation of Pos Line Status.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPosLineStatusEntry

rcPosLineStatusIndex		1.3.6.1.4.1.2272.1.26.3.1.1
pos ifIndex, same as rcPosPppIpxIfIndex.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcPosLineStatusLocalMACAddress		1.3.6.1.4.1.2272.1.26.3.1.2
current local MAC address
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rcPosLineStatusRemoteMACAddress		1.3.6.1.4.1.2272.1.26.3.1.3
current remote MAC address
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rcPosLineStatusLocalIpAddr		1.3.6.1.4.1.2272.1.26.3.1.4
current local ip addr
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcPosLineStatusRemoteIpAddr		1.3.6.1.4.1.2272.1.26.3.1.5
current remote ip addr
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcPosLineStatusOutQuality		1.3.6.1.4.1.2272.1.26.3.1.6
current output quality.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPosLineStatusLocalPeriod		1.3.6.1.4.1.2272.1.26.3.1.7
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPosLineStatusDeviceType		1.3.6.1.4.1.2272.1.26.3.1.8
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPosLineStatusDeviceRev		1.3.6.1.4.1.2272.1.26.3.1.9
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPosLineStatusIpxRoutingProtocol		1.3.6.1.4.1.2272.1.26.3.1.10
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPosLineConfigTable		1.3.6.1.4.1.2272.1.26.4
Pos Line Config Table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPosLineConfigEntry

rcPosLineConfigEntry		1.3.6.1.4.1.2272.1.26.4.1
Entry containing infomation of Pos Line Config.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPosLineConfigEntry

rcPosLineConfigIndex		1.3.6.1.4.1.2272.1.26.4.1.1
pos ifIndex, same as rcPosPppIpxIfIndex.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcPosLineConfigLocalMACAddress		1.3.6.1.4.1.2272.1.26.4.1.2
current local MAC address
Status: current	Access: read-write
OBJECT-TYPE
	MacAddress

rcPosLineConfigRemoteMACAddress		1.3.6.1.4.1.2272.1.26.4.1.3
current remote MAC address
Status: current	Access: read-write
OBJECT-TYPE
	MacAddress

rcPosLineConfigLocalIpAddr		1.3.6.1.4.1.2272.1.26.4.1.4
current local ip addr
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcPosLineConfigRemoteIpAddr		1.3.6.1.4.1.2272.1.26.4.1.5
current remote ip addr
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcPosLineConfigRemoteReportPeriod		1.3.6.1.4.1.2272.1.26.4.1.6
config. remote report period.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..60

rcPosLineConfigLqrThreshold		1.3.6.1.4.1.2272.1.26.4.1.7
config. input quality.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..100

rcPosLineConfigOutQuality		1.3.6.1.4.1.2272.1.26.4.1.8
config. output quality.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcPosLineConfigPppStp		1.3.6.1.4.1.2272.1.26.4.1.9
STP PPP encoding enable T/F
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcPosLineConfigLoopBack		1.3.6.1.4.1.2272.1.26.4.1.10
perform loop-back.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcPosLineConfigIpxVlanMacAddress		1.3.6.1.4.1.2272.1.26.4.1.11
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	MacAddress

rcPosLineConfigIpxRemoteMacAddress		1.3.6.1.4.1.2272.1.26.4.1.12
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	MacAddress

rcPosSonetTrap		1.3.6.1.4.1.2272.1.26.5
OBJECT IDENTIFIER

rcPosSonetTrapType		1.3.6.1.4.1.2272.1.26.5.1
Used to indicate a particular type of Sonet trap.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	sectionAlarm(1), lineAlarm(2), pathAlarm(3)

rcPosSonetTrapIndication		1.3.6.1.4.1.2272.1.26.5.2
Used to indicate an indication for a Sonet trap.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	noDefect(1), sectionLossOfSignal(2), sectionLossOfFrame(3), lineAlarmIndication(4), lineRemoteDefectIndication(5), pathLossOfPointer(6), pathAlarmIndication(7), pathRemoteDefectIndication(8), pathUnequipped(9), pathSignalLabelMismatch(10), pathTraceMismatch(11)

rcPosSioCardConfigTable		1.3.6.1.4.1.2272.1.26.6
Pos Sio Card Config Table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPosSioCardConfigEntry

rcPosSioCardConfigEntry		1.3.6.1.4.1.2272.1.26.6.1
Entry containing infomation of Pos Sio Card Config.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPosSioCardConfigEntry

rcPosSioCardConfigSlotIndex		1.3.6.1.4.1.2272.1.26.6.1.1
slot Index.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

rcPosSioCardConfigAction		1.3.6.1.4.1.2272.1.26.6.1.2
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(0), reset(1)

rcPosSioCardConfigTraceMode		1.3.6.1.4.1.2272.1.26.6.1.3
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(0), traceOn(1)

rcPosSioCardConfigImageFileName		1.3.6.1.4.1.2272.1.26.6.1.4
POS Image file name.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

rcPosOperStatusTable		1.3.6.1.4.1.2272.1.26.7
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPosOperStatusEntry

rcPosOperStatusEntry		1.3.6.1.4.1.2272.1.26.7.1
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPosOperStatusEntry

rcPosOperStatusIndex		1.3.6.1.4.1.2272.1.26.7.1.1
pos ifIndex.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcPosOperStatusLqrStatus		1.3.6.1.4.1.2272.1.26.7.1.2
Operational status of pppLqrConfigStatus.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPosOperStatusLineLqrThreshold		1.3.6.1.4.1.2272.1.26.7.1.3
.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPosOperStatusLinkMagicNumber		1.3.6.1.4.1.2272.1.26.7.1.4
.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPosOperStatusLinePppStp		1.3.6.1.4.1.2272.1.26.7.1.5
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	EnableValue

rcLinkFlapDetectAutoPortDownEnable		1.3.6.1.4.1.2272.1.27.1
Used to enable/disable the Link Flap Detect feature. When enabled this feature will monitor the number of times a port goes down during a certain interval. If the number exceeds a given bound the port will be forced out-of-service.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcLinkFlapDetectSendTrap		1.3.6.1.4.1.2272.1.27.2
Used to configure whether a trap should be sent if the port is forced out-of-service.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcLinkFlapDetectFrequency		1.3.6.1.4.1.2272.1.27.3
Used to configure the number of times the port can go down.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..9999

rcLinkFlapDetectInterval		1.3.6.1.4.1.2272.1.27.4
Used to configure the interval (in minutes).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	2..600

rcRadiusGlobal		1.3.6.1.4.1.2272.1.29.1
OBJECT IDENTIFIER

rcRadiusGlobalEnable		1.3.6.1.4.1.2272.1.29.1.1
Enable/disable this feature.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcRadiusGlobalMaxNumberServer		1.3.6.1.4.1.2272.1.29.1.2
Maximum number of RADIUS servers.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..10

rcRadiusGlobalAttributeValue		1.3.6.1.4.1.2272.1.29.1.3
Integer value for Access-Priority attribute.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	192..240

rcRadiusGlobalServerTableSize		1.3.6.1.4.1.2272.1.29.1.4
Used to indicate the number of entries in the rcRadiusServerTable.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcRadiusGlobalAcctEnable		1.3.6.1.4.1.2272.1.29.1.5
Enable/disable Radius Accounting feature.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcRadiusGlobalAcctAttributeValue		1.3.6.1.4.1.2272.1.29.1.6
Integer value for User-Command attribute.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	192..240

rcRadiusGlobalAcctIncludeCli		1.3.6.1.4.1.2272.1.29.1.7
Include/Exclude cli-commands in radius acccounting updates.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcRadiusGlobalClearStat		1.3.6.1.4.1.2272.1.29.1.8
Clear Radius Statistic for all servers configured.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcRadiusGlobalMcastAttributeValue		1.3.6.1.4.1.2272.1.29.1.9
Integer value for multicast address vendor specific attribute.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

rcRadiusGlobalAuthInfoAttributeValue		1.3.6.1.4.1.2272.1.29.1.10
Integer value for Auth-Info vendor specific attribute.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

rcRadiusGlobalCommandAccess		1.3.6.1.4.1.2272.1.29.1.11
Integer value for Command-Access attribute.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	192..240

rcRadiusGlobalCliCommands		1.3.6.1.4.1.2272.1.29.1.12
Integer value for Cli-Command attribute.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	192..240

rcRadiusGlobalIgapLogFSize		1.3.6.1.4.1.2272.1.29.1.13
Maximum size for the IGAP accounting time-out log file in KB.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	50..8192

rcRadiusGlobalCliProfEnable		1.3.6.1.4.1.2272.1.29.1.14
Enable/disable Radius CLI Profiling.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcRadiusGlobalAuthInvalidServerAddress		1.3.6.1.4.1.2272.1.29.1.15
Number of Access Responses from unknown or invalid Radius servers.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcRadiusGlobalSourceIpFlag		1.3.6.1.4.1.2272.1.29.1.16
Flag to include configured IP address as source address in RADIUS packets.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcRadiusGlobalCliCmdCount		1.3.6.1.4.1.2272.1.29.1.18
Integer value for Cli-Command-count.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..40

rcRadiusServerTable		1.3.6.1.4.1.2272.1.29.2
The RADIUS table (0 to 10 entries). This table lists the information of the RADIUS server.
Status: obsolete	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcRadiusServerEntry

rcRadiusServerEntry		1.3.6.1.4.1.2272.1.29.2.1
A RADIUS server table entry.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	RcRadiusServerEntry

rcRadiusServerPriority		1.3.6.1.4.1.2272.1.29.2.1.1
Server priority, used to control which server to choose first to send authentication.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	1..10

rcRadiusServerAddress		1.3.6.1.4.1.2272.1.29.2.1.2
Server IP address of the RADIUS authentication server referred to in this table entry.
Status: deprecated	Access: read-write
OBJECT-TYPE
	IpAddress

rcRadiusServerTimeOut		1.3.6.1.4.1.2272.1.29.2.1.3
The time interval in seconds before the client retransmit the packet.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	1..10

rcRadiusServerEnable		1.3.6.1.4.1.2272.1.29.2.1.4
Enable or disable this server.
Status: deprecated	Access: read-write
OBJECT-TYPE
	TruthValue

rcRadiusServerMaxRetries		1.3.6.1.4.1.2272.1.29.2.1.5
Maximum number of retransmissions.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	1..6

rcRadiusServerUdpPort		1.3.6.1.4.1.2272.1.29.2.1.6
The UDP port the client is using to send requests to this server.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	1..65536

rcRadiusServerSecretKey		1.3.6.1.4.1.2272.1.29.2.1.7
The identifier of the RADIUS authentication client.
Status: deprecated	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

rcRadiusServerAccessRequests		1.3.6.1.4.1.2272.1.29.2.1.8
The number of RADIUS access-response packets sent to this server. This does not include retransmissions.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcRadiusServerAccessAccepts		1.3.6.1.4.1.2272.1.29.2.1.9
The number of RADIUS access-accept packets (valid or invalid) received from this server.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcRadiusServerAccessRejects		1.3.6.1.4.1.2272.1.29.2.1.10
The number of RADIUS access-reject packets (valid or invalid) received from this server.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcRadiusServerBadResponses		1.3.6.1.4.1.2272.1.29.2.1.11
The number of RADIUS invalid access-response packets received from this server.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcRadiusServerPendingRequests		1.3.6.1.4.1.2272.1.29.2.1.12
The number of RADIUS access-request packets destined for this server that have not yet timed out or received a response. This variable is incremented when an access-request is sent and decremented due to receipt of an access-accept, access-reject, a timeout or retransmission.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcRadiusServerClientRetries		1.3.6.1.4.1.2272.1.29.2.1.13
The number of authentication retransmission to this server.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcRadiusServerRowStatus		1.3.6.1.4.1.2272.1.29.2.1.14
Used to create/delete entries.
Status: deprecated	Access: read-write
OBJECT-TYPE
	RowStatus

rcRadiusServerAcctEnable		1.3.6.1.4.1.2272.1.29.2.1.15
Enable or disable Radius Accounting on this server.
Status: deprecated	Access: read-write
OBJECT-TYPE
	TruthValue

rcRadiusServerAcctUdpPort		1.3.6.1.4.1.2272.1.29.2.1.16
The UDP port the client used to send accounting requests to this server.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	1..65536

rcRadiusServerAcctOnRequests		1.3.6.1.4.1.2272.1.29.2.1.17
The number of RADIUS accounting-on packets sent to this server. This does not include retransmissions.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcRadiusServerAcctOffRequests		1.3.6.1.4.1.2272.1.29.2.1.18
The number of RADIUS accounting-off packets sent to this server. This does not include retransmissions.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcRadiusServerAcctStartRequests		1.3.6.1.4.1.2272.1.29.2.1.19
The number of RADIUS accounting-start packets sent to this server. This does not include retransmissions.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcRadiusServerAcctStopRequests		1.3.6.1.4.1.2272.1.29.2.1.20
The number of RADIUS accounting-stop packets sent to this server. This does not include retransmissions.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcRadiusServerAcctInterimRequests		1.3.6.1.4.1.2272.1.29.2.1.21
The number of RADIUS accounting-interim packets sent to this server. This does not include retransmissions.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcRadiusServerAcctBadResponses		1.3.6.1.4.1.2272.1.29.2.1.22
The number of Invalid responses received from this server.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcRadiusServerAcctPendingRequests		1.3.6.1.4.1.2272.1.29.2.1.23
The number of RADIUS accounting packets that are waiting be sent to this server. This variable is incremented whenever any accounting-request is sent to this server and decremented when an acknowledgement is received or timeout occurs.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcRadiusServerAcctClientRetries		1.3.6.1.4.1.2272.1.29.2.1.24
The number of RADIUS accounting packets retransmitted to this server.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

rcRadiusServTable		1.3.6.1.4.1.2272.1.29.3
The RADIUS table (0 to 10 entries). This table lists the information of the RADIUS server.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcRadiusServEntry

rcRadiusServEntry		1.3.6.1.4.1.2272.1.29.3.1
A RADIUS server table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcRadiusServEntry

rcRadiusServPriority		1.3.6.1.4.1.2272.1.29.3.1.1
Server priority, used to control which server to choose first to send authentication.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..10

rcRadiusServAddress		1.3.6.1.4.1.2272.1.29.3.1.2
Server IP address of the RADIUS authentication server referred to in this table entry.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcRadiusServTimeOut		1.3.6.1.4.1.2272.1.29.3.1.3
The time interval in seconds before the client retransmit the packet.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..20

rcRadiusServEnable		1.3.6.1.4.1.2272.1.29.3.1.4
Enable or disable this server.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcRadiusServMaxRetries		1.3.6.1.4.1.2272.1.29.3.1.5
Maximum number of retransmissions.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..6

rcRadiusServUdpPort		1.3.6.1.4.1.2272.1.29.3.1.6
The UDP port the client is using to send requests to this server.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..65536

rcRadiusServSecretKey		1.3.6.1.4.1.2272.1.29.3.1.7
The identifier of the RADIUS authentication client.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..32)

rcRadiusServAccessRequests		1.3.6.1.4.1.2272.1.29.3.1.8
The number of RADIUS access-response packets sent to this server. This does not include retransmissions.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcRadiusServAccessAccepts		1.3.6.1.4.1.2272.1.29.3.1.9
The number of RADIUS access-accept packets (valid or invalid) received from this server.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcRadiusServAccessRejects		1.3.6.1.4.1.2272.1.29.3.1.10
The number of RADIUS access-reject packets (valid or invalid) received from this server.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcRadiusServBadResponses		1.3.6.1.4.1.2272.1.29.3.1.11
The number of RADIUS invalid access-response packets received from this server.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcRadiusServPendingRequests		1.3.6.1.4.1.2272.1.29.3.1.12
The number of RADIUS access-request packets destined for this server that have not yet timed out or received a response. This variable is incremented when an access-request is sent and decremented due to receipt of an access-accept, access-reject, a timeout or retransmission.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcRadiusServClientRetries		1.3.6.1.4.1.2272.1.29.3.1.13
The number of authentication retransmission to this server.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcRadiusServRowStatus		1.3.6.1.4.1.2272.1.29.3.1.14
Used to create/delete entries.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcRadiusServAcctEnable		1.3.6.1.4.1.2272.1.29.3.1.15
Enable or disable Radius Accounting on this server.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcRadiusServAcctUdpPort		1.3.6.1.4.1.2272.1.29.3.1.16
The UDP port the client used to send accounting requests to this server.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..65536

rcRadiusServAcctOnRequests		1.3.6.1.4.1.2272.1.29.3.1.17
The number of RADIUS accounting-on packets sent to this server. This does not include retransmissions.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcRadiusServAcctOffRequests		1.3.6.1.4.1.2272.1.29.3.1.18
The number of RADIUS accounting-off packets sent to this server. This does not include retransmissions.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcRadiusServAcctStartRequests		1.3.6.1.4.1.2272.1.29.3.1.19
The number of RADIUS accounting-start packets sent to this server. This does not include retransmissions.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcRadiusServAcctStopRequests		1.3.6.1.4.1.2272.1.29.3.1.20
The number of RADIUS accounting-stop packets sent to this server. This does not include retransmissions.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcRadiusServAcctInterimRequests		1.3.6.1.4.1.2272.1.29.3.1.21
The number of RADIUS accounting-interim packets sent to this server. This does not include retransmissions.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcRadiusServAcctBadResponses		1.3.6.1.4.1.2272.1.29.3.1.22
The number of Invalid responses received from this server.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcRadiusServAcctPendingRequests		1.3.6.1.4.1.2272.1.29.3.1.23
The number of RADIUS accounting packets that are waiting be sent to this server. This variable is incremented whenever any accounting-request is sent to this server and decremented when an acknowledgement is received or timeout occurs.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcRadiusServAcctClientRetries		1.3.6.1.4.1.2272.1.29.3.1.24
The number of RADIUS accounting packets retransmitted to this server.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcRadiusServUsedBy		1.3.6.1.4.1.2272.1.29.3.1.25
cli(1): for cli login, igap(2): for igap,snmp(3): for snmp login, eap(4) for EAP PAE Authenticator, web(5) for EDM login.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	cli(1), igap(2), snmp(3), eap(4), web(5)

rcRadiusServNasIpAddress		1.3.6.1.4.1.2272.1.29.3.1.26
RADIUS Client NAS Identifier for this server.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcRadiusServRoundTripTime		1.3.6.1.4.1.2272.1.29.3.1.27
Time different between the instance when a RADIUS request is sent and the corresponding response is received.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..20)

rcRadiusServAccessChallanges		1.3.6.1.4.1.2272.1.29.3.1.28
The number of RADIUS access-challanges packets sent to this server. This does not include retransmission.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcRadiusServSourceIpAddr		1.3.6.1.4.1.2272.1.29.3.1.29
source IP address RADIUS packets.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcRadiusGlobalSnmp		1.3.6.1.4.1.2272.1.29.4
OBJECT IDENTIFIER

rcRadiusGlobalSnmpEnable		1.3.6.1.4.1.2272.1.29.4.1
Enable/disable snmp radius authentication.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcRadiusGlobalSnmpAcctEnable		1.3.6.1.4.1.2272.1.29.4.2
Enable/disable Radius Accounting for SNMP.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcRadiusGlobalSnmpReAuthenticateTimer		1.3.6.1.4.1.2272.1.29.4.3
Integer value representing Re-Authenticate Timer in seconds. Timer to be used to Re- Authenticate a SNMP Session.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	30..65535

rcRadiusGlobalSnmpAbortSessionTimer		1.3.6.1.4.1.2272.1.29.4.4
Integer value representing the time in seconds after which the snmp session is considered expired and Radius Accounting Stop message is sent.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	30..65535

rcRadiusGlobalSnmpUserName		1.3.6.1.4.1.2272.1.29.4.5
User name for Radius SNMP Accounting.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

rcRadiusEapLastRejMac		1.3.6.1.4.1.2272.1.29.4.6
Used to store the Last Rejected MAC address on an EAP enabled port.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rcRadiusPaePortNumber		1.3.6.1.4.1.2272.1.29.4.7
Used to store the Port Number on which the Mac Intrusion happened.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcRadiusEapLastAuthMac		1.3.6.1.4.1.2272.1.29.4.8
Used to store the Last Authenticated MAC address on an EAP enabled port.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rcTacacsGlobal		1.3.6.1.4.1.2272.1.65.1
OBJECT IDENTIFIER

rcTacacsGlobalEnable		1.3.6.1.4.1.2272.1.65.1.1
Enable/disable this feature.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcTacacsGlobalLastUserName		1.3.6.1.4.1.2272.1.65.1.2
The last user for which authentication was attempted using TACACS+.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(1..128)

rcTacacsGlobalLastAddressType		1.3.6.1.4.1.2272.1.65.1.3
The type of address for the TACACS+ server that was most recently accessed
Status: current	Access: read-only
OBJECT-TYPE
	InetAddressType

rcTacacsGlobalLastAddress		1.3.6.1.4.1.2272.1.65.1.4
The address of the TACACS+ server that was most recently accessed
Status: current	Access: read-only
OBJECT-TYPE
	InetAddress

rcTacacsAccounting		1.3.6.1.4.1.2272.1.65.1.5
Determines which application will be accounted by tacacs+.
Status: current	Access: read-write
OBJECT-TYPE
	BITS	cli(0), ppp(1)

rcTacacsAuthentication		2.1.3.6.1.4.1.2272.1.65.1.6
Determines which application will be authenticated by tacacs+.
Status: current	Access: read-write
OBJECT-TYPE
	BITS	cli(0), ppp(1), web(2)

rcTacacsServerTable		1.3.6.1.4.1.2272.1.65.2
The (conceptual) table listing the TACACS+ servers with which the client shares a secret.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcTacacsServerEntry

rcTacacsServerEntry		1.3.6.1.4.1.2272.1.65.2.1
An entry (conceptual row) representing a TACACS+ server with which the client shares a secret.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcTacacsServerEntry

rcTacacsServerAddressType		1.3.6.1.4.1.2272.1.65.2.1.1
Specifies the type of IP address used on the Tacacs+ server.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddressType

rcTacacsServerAddress		1.3.6.1.4.1.2272.1.65.2.1.2
The IP address of the TACACS+ server referred to in this table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddress

rcTacacsServerPortNumber		1.3.6.1.4.1.2272.1.65.2.1.3
The TCP port on which the client establishes a connection to the server. A value of 0 indicates that the system specified default value is used.
Status: current	Access: read-create
OBJECT-TYPE
	InetPortNumber

rcTacacsServerConnectionType		1.3.6.1.4.1.2272.1.65.2.1.4
Specifies TCP connection type between device and TACACS+ server. Either a single open connection between a device and server (SingleConnection), or open/close connection per communication session (PerSessionConnection).
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	singleConnection(1), perSessionConnection(2)

rcTacacsServerConnectionStatus		1.3.6.1.4.1.2272.1.65.2.1.5
Specifies status TCP connection type between device and TACACS+ server.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	connected(1), notConnected(2)

rcTacacsServerTimeout		1.3.6.1.4.1.2272.1.65.2.1.6
The maximum time (in seconds) to wait for this TACACS+ server to reply.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	10..30

rcTacacsServerKey		1.3.6.1.4.1.2272.1.65.2.1.7
Secret key to be shared with this TACACS+ server. If the key length is zero that indicates no encryption is being used.
Status: current	Access: read-create
OBJECT-TYPE
	OCTET STRING	Size(0..128)

rcTacacsServerSourceIpInterfaceEnabled		1.3.6.1.4.1.2272.1.65.2.1.8
Specifies whether source address specification is enabled.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcTacacsServerSourceIpInterfaceType		1.3.6.1.4.1.2272.1.65.2.1.9
Specifies the type of IP address used on the interface that connects to the Tacacs+ server. If this value is unknown(0), then a system-wide default value will be used.
Status: current	Access: read-create
OBJECT-TYPE
	InetAddressType

rcTacacsServerSourceIpInterface		1.3.6.1.4.1.2272.1.65.2.1.10
IP address of the interface to use with this server.
Status: current	Access: read-create
OBJECT-TYPE
	InetAddress

rcTacacsServerPriority		1.3.6.1.4.1.2272.1.65.2.1.11
Determines the order in which the TACACS+ servers will be used, when 1 is the highest priority. If more than one server share the same priority - they will be used in lexicographic order (the order of entries in this table).
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..65535

rcTacacsServerRowStatus		1.3.6.1.4.1.2272.1.65.2.1.12
The row status variable, can be set to destroy or createAndGo.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcIgmpInterfaceExtnTable		1.3.6.1.4.1.2272.1.30.1
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIgmpInterfaceExtnEntry

rcIgmpInterfaceExtnEntry		1.3.6.1.4.1.2272.1.30.1.1
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIgmpInterfaceExtnEntry

rcIgmpInterfaceExtnIfIndex		1.3.6.1.4.1.2272.1.30.1.1.1
ifindex.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcIgmpInterfaceExtnSnoopEnable		1.3.6.1.4.1.2272.1.30.1.1.2
enable snoop.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIgmpInterfaceExtnProxySnoopEnable		1.3.6.1.4.1.2272.1.30.1.1.3
enable proxy snoop.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIgmpInterfaceExtnMaxAdvertiseInterval		1.3.6.1.4.1.2272.1.30.1.1.4
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	2..180

rcIgmpInterfaceExtnMinAdvertiseInterval		1.3.6.1.4.1.2272.1.30.1.1.5
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	3..180

rcIgmpInterfaceExtnMaxInitialAdvertiseInterval		1.3.6.1.4.1.2272.1.30.1.1.6
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcIgmpInterfaceExtnMaxInitialAdvertments		1.3.6.1.4.1.2272.1.30.1.1.7
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcIgmpInterfaceExtnNeighborDeadInterval		1.3.6.1.4.1.2272.1.30.1.1.8
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcIgmpInterfaceExtnFastLeaveEnable		1.3.6.1.4.1.2272.1.30.1.1.9
Enable fast leave on this interface.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIgmpInterfaceExtnFastLeavePortMembers		1.3.6.1.4.1.2272.1.30.1.1.10
The set of ports that are enabled for fast leave.
Status: current	Access: read-write
OBJECT-TYPE
	PortSet

rcIgmpInterfaceExtnMrdiscEnable		1.3.6.1.4.1.2272.1.30.1.1.11
Enable/disable multicast router discovery.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIgmpInterfaceExtnDiscoveredRouterPorts		1.3.6.1.4.1.2272.1.30.1.1.12
list of ports that discovered by IGMP Multicast router discovery (MRDISC) protocol.
Status: current	Access: read-only
OBJECT-TYPE
	PortSet

rcIgmpInterfaceExtnSnoopMRouterPorts		1.3.6.1.4.1.2272.1.30.1.1.13
The set of ports in this interface that provide connectivity to an IP Multicast router.
Status: current	Access: read-write
OBJECT-TYPE
	PortSet

rcIgmpInterfaceExtnSnoopActiveMRouterPorts		1.3.6.1.4.1.2272.1.30.1.1.14
Active ports.
Status: current	Access: read-only
OBJECT-TYPE
	PortSet

rcIgmpInterfaceExtnSnoopMRouterExpiration		1.3.6.1.4.1.2272.1.30.1.1.15
Multicast querier router aging time out.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIgmpInterfaceExtnFlushAction		1.3.6.1.4.1.2272.1.30.1.1.16
IGMP flush action.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), flushGrpMember(2), flushMrouter(3), flushSender(4)

rcIgmpInterfaceExtnRouterAlertEnable		1.3.6.1.4.1.2272.1.30.1.1.17
Enable Router Alert Check.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIgmpInterfaceExtnSsmEnable		1.3.6.1.4.1.2272.1.30.1.1.18
enable SSM.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIgmpInterfaceExtnIgapEnable		1.3.6.1.4.1.2272.1.30.1.1.19
enable/disable IGAP.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIgmpInterfaceExtnAccntEnable		1.3.6.1.4.1.2272.1.30.1.1.20
enable/disable accounting.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIgmpInterfaceExtnAuthEnable		1.3.6.1.4.1.2272.1.30.1.1.21
enable/disable authentication.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIgmpInterfaceExtnStreamLimitEnable		1.3.6.1.4.1.2272.1.30.1.1.22
Stream Limitation enable/disable.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIgmpInterfaceExtnMaxStreams		1.3.6.1.4.1.2272.1.30.1.1.23
Maximum number of stream.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcIgmpInterfaceExtnNumStreams		1.3.6.1.4.1.2272.1.30.1.1.24
Current number of streams.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIgmpInterfaceExtnNewQuerier		1.3.6.1.4.1.2272.1.30.1.1.25
The address of the New IGMP Querier on the IP subnet to which this interface is attached.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIgmpInterfaceExtnSnoopQuerierEnable		1.3.6.1.4.1.2272.1.30.1.1.26
enable snoop querier.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIgmpInterfaceExtnSnoopQuerierAddr		1.3.6.1.4.1.2272.1.30.1.1.27
The pseudo address of the IGMP Snoop Querier.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcIgmpInterfaceExtnMvrEnable		1.3.6.1.4.1.2272.1.30.1.1.28
Enable or disable mcast-vlan-registration on a vlan, it is used to specified a vlan works as a mcast-vlan, maximum 16 mcast-vlan is supported.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIgmpInterfaceExtnMvrProxyEnable		1.3.6.1.4.1.2272.1.30.1.1.29
enable or disable mcast-vlan-registration proxy on a vlan, you must enable mcast-vlan-registration at first.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIgmpInterfaceExtnDynamicDowngradeEnable		1.3.6.1.4.1.2272.1.30.1.1.30
enable dynamic downgrade the IGMP version when older version query message was received.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIgmpInterfaceExtnCompatibilityModeEnable		1.3.6.1.4.1.2272.1.30.1.1.31
enable v2 v3 compatible mode, which will handle the IGMP v2 message in v3 interface.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIgmpInterfaceExtnOperVersion		1.3.6.1.4.1.2272.1.30.1.1.32
The operational version of IGMP which is running on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	version1(1), version2(2), version3(3)

rcIgmpStaticTable		1.3.6.1.4.1.2272.1.30.2
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIgmpStaticEntry

rcIgmpStaticEntry		1.3.6.1.4.1.2272.1.30.2.1
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIgmpStaticEntry

rcIgmpStaticIfIndex		1.3.6.1.4.1.2272.1.30.2.1.1
ifindex
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcIgmpStaticGrpAddr		1.3.6.1.4.1.2272.1.30.2.1.2
Ip multicast address. The GrpAddress holds the starting range for the address range. If the ToGrpAddress is not entered, the it is as good as entering a single address.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIgmpStaticMemberPorts		1.3.6.1.4.1.2272.1.30.2.1.3
egressing ports.
Status: current	Access: read-write
OBJECT-TYPE
	PortSet

rcIgmpStaticNotAllowedToJoin		1.3.6.1.4.1.2272.1.30.2.1.4
not allowed to join.
Status: current	Access: read-write
OBJECT-TYPE
	PortSet

rcIgmpStaticRowStatus		1.3.6.1.4.1.2272.1.30.2.1.5
Used to create/delete entries in the rcIgmpStaticEntry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIgmpStaticToGrpAddr		1.3.6.1.4.1.2272.1.30.2.1.6
To hold the range for the GrpAddress.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcIgmpAccessTable		1.3.6.1.4.1.2272.1.30.3
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIgmpAccessEntry

rcIgmpAccessEntry		1.3.6.1.4.1.2272.1.30.3.1
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIgmpAccessEntry

rcIgmpAccessIfIndex		1.3.6.1.4.1.2272.1.30.3.1.1
ifindex
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcIgmpAccessGrpAddr		1.3.6.1.4.1.2272.1.30.3.1.2
ip multicast addr.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIgmpAccessHostAddr		1.3.6.1.4.1.2272.1.30.3.1.3
host addr.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIgmpAccessMode		1.3.6.1.4.1.2272.1.30.3.1.4
denyTX(1), denyRX(2), denyBOTH(3).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	denyTX(1), denyRX(2), denyBOTH(3)

rcIgmpAccessRowStatus		1.3.6.1.4.1.2272.1.30.3.1.5
Used to create/delete entries in the rcIgmpAccessEntry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIgmpAccessHostMask		1.3.6.1.4.1.2272.1.30.3.1.6
host mask.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIgmpSenderTable		1.3.6.1.4.1.2272.1.30.4
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIgmpSenderEntry

rcIgmpSenderEntry		1.3.6.1.4.1.2272.1.30.4.1
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIgmpSenderEntry

rcIgmpSenderGrpAddr		1.3.6.1.4.1.2272.1.30.4.1.1
ip multicast addr.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIgmpSenderIfIndex		1.3.6.1.4.1.2272.1.30.4.1.2
ifindex
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcIgmpSenderMemberAddr		1.3.6.1.4.1.2272.1.30.4.1.3
host addr.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIgmpSenderAction		1.3.6.1.4.1.2272.1.30.4.1.4
none(0), flushEntry(1), flushGrp(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), flushEntry(1), flushGrp(2)

rcIgmpSenderTPort		1.3.6.1.4.1.2272.1.30.4.1.5
Igmp Sender Tport.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIgmpSenderState		1.3.6.1.4.1.2272.1.30.4.1.6
Indicates if a sender exists because of an IGMP access filter or not.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	filtered(1), notfiltered(2)

rcIgmpSsmGlobal		1.3.6.1.4.1.2272.1.30.5
OBJECT IDENTIFIER

rcIgmpSsmGlobalDynamicLearning		1.3.6.1.4.1.2272.1.30.5.1
Enable/disable dynamic learning or source/group pair from IGMPv3 report.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIgmpSsmGlobalAdminAction		1.3.6.1.4.1.2272.1.30.5.2
Set the admin status of all the Ssm entries to enable/disable at once.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), enableAll(2), disableAll(3)

rcIgmpSsmGlobalRangeGroup		1.3.6.1.4.1.2272.1.30.5.3
If multicast group address & RangeMask == RangeGroup, then RangeGroup is in Ssm Range. Else it is not in the range.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcIgmpSsmGlobalRangeMask		1.3.6.1.4.1.2272.1.30.5.4
Used with RangeGroup.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcIgmpSsmTable		1.3.6.1.4.1.2272.1.30.6
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIgmpSsmEntry

rcIgmpSsmEntry		1.3.6.1.4.1.2272.1.30.6.1
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIgmpSsmEntry

rcIgmpSsmIpMulticastGrp		1.3.6.1.4.1.2272.1.30.6.1.1
This is the IP multicast group address that has default range of 232/8. This parameter should be configured by the user.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIgmpSsmIpSource		1.3.6.1.4.1.2272.1.30.6.1.2
This is the Source's IP address that will be sending traffic to the group source. This parameter should be configured by the user.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcIgmpSsmLearningMode		1.3.6.1.4.1.2272.1.30.6.1.3
This is a read only field that provides information if the entry is statically configured entry (Static) or a dynamically learned entry from IGMPv3 (Dynamic). Note that Dynamic may not be used in the first step of the implementation.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	dynamic(1), static(2)

rcIgmpSsmActivity		1.3.6.1.4.1.2272.1.30.6.1.4
This is a read only field. It provides the activity on the corresponding (S,G). If the source is active and traffic is flowing to the switch, this field value should be Active, otherwise it should say non-active. This information is useful in knowing if the group has an active source or not when the group is joined by a member on the switch.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcIgmpSsmAdminState		1.3.6.1.4.1.2272.1.30.6.1.5
The admin state provides information on whether the entry is to be used or not. If the value of this field is Enabled (default), then the entry can be used. If the state is Disabled, then the entry will not be used, but will be saved for future use.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIgmpSsmRowStatus		1.3.6.1.4.1.2272.1.30.6.1.6
Used to create/delete entries.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIgmpNewAccessTable		1.3.6.1.4.1.2272.1.30.7
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIgmpNewAccessEntry

rcIgmpNewAccessEntry		1.3.6.1.4.1.2272.1.30.7.1
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIgmpNewAccessEntry

rcIgmpNewAccessIfIndex		1.3.6.1.4.1.2272.1.30.7.1.1
ifindex
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcIgmpNewAccessPrefixListId		1.3.6.1.4.1.2272.1.30.7.1.2
Prefix List ID.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

rcIgmpNewAccessPrefixListName		1.3.6.1.4.1.2272.1.30.7.1.3
Prefix List name.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rcIgmpNewAccessHostAddr		1.3.6.1.4.1.2272.1.30.7.1.4
host addr.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIgmpNewAccessHostMask		1.3.6.1.4.1.2272.1.30.7.1.5
host mask.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIgmpNewAccessActionMode		1.3.6.1.4.1.2272.1.30.7.1.6
action mode.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	denyTX(1), denyRX(2), denyBOTH(3), allowTX(4), allowRX(5), allowBOTH(6)

rcIgmpNewAccessRowStatus		1.3.6.1.4.1.2272.1.30.7.1.7
Used to create/delete entries in the rcIgmpNewAccessEntry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIgmpChannelLimitTable		1.3.6.1.4.1.2272.1.30.8
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIgmpChannelLimitEntry

rcIgmpChannelLimitEntry		1.3.6.1.4.1.2272.1.30.8.1
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIgmpChannelLimitEntry

rcIgmpChannelLimitIfIndex		1.3.6.1.4.1.2272.1.30.8.1.1
ifindex
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcIgmpChannelLimitPort		1.3.6.1.4.1.2272.1.30.8.1.2
The port belong to this vlan.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

rcIgmpChannelLimitMaxStreams		1.3.6.1.4.1.2272.1.30.8.1.3
Maximum number of stream.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..65535

rcIgmpChannelLimitNumStreams		1.3.6.1.4.1.2272.1.30.8.1.4
Current number of streams.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIgmpChannelLimitRowStatus		1.3.6.1.4.1.2272.1.30.8.1.5
Row Status.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcIgmpIgapServiceAbilityTable		1.3.6.1.4.1.2272.1.30.9
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIgmpIgapServiceAbilityEntry

rcIgmpIgapServiceAbilityEntry		1.3.6.1.4.1.2272.1.30.9.1
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIgmpIgapServiceAbilityEntry

rcIgmpIgapServiceAbilityIfIndex		1.3.6.1.4.1.2272.1.30.9.1.1
ifindex
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcIgmpIgapServiceAbilityAuthSuccess		1.3.6.1.4.1.2272.1.30.9.1.2
The port belong to this vlan.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcIgmpIgapServiceAbilityAuthReject		1.3.6.1.4.1.2272.1.30.9.1.3
Maximum number of stream.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcIgmpIgapServiceAbilityRespTimeout		1.3.6.1.4.1.2272.1.30.9.1.4
Current number of streams.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcIgmpIgapServiceAbilityPapJoinReq		1.3.6.1.4.1.2272.1.30.9.1.5
Row Status.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcIgmpIgapServiceAbilityBasicQuery		1.3.6.1.4.1.2272.1.30.9.1.6
Current number of streams.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcIgmpIgapServiceAbilityBasicLeave		1.3.6.1.4.1.2272.1.30.9.1.7
Row Status.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcIgmpIgapServiceAbilityClearStat		1.3.6.1.4.1.2272.1.30.9.1.8
Clear Counter.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIgmpIgapGlobal		1.3.6.1.4.1.2272.1.30.10
OBJECT IDENTIFIER

rcIgmpIgapGlobalClearAllStat		1.3.6.1.4.1.2272.1.30.10.1
Clear All IGAP Counters.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIgmpGlobalParams		1.3.6.1.4.1.2272.1.30.11
OBJECT IDENTIFIER

rcIgmpFastLeaveMode		1.3.6.1.4.1.2272.1.30.11.1
Set the fast-leave mode to be used by for all fast-leave enabled IGMP interfaces.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), multipleUser(1), oneUser(2)

rcIgmpCacheExtnTable		1.3.6.1.4.1.2272.1.30.12
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIgmpCacheExtnEntry

rcIgmpCacheExtnEntry		1.3.6.1.4.1.2272.1.30.12.1
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIgmpCacheExtnEntry

rcIgmpCacheExtnType		1.3.6.1.4.1.2272.1.30.12.1.1
It takes up either of the two values, dynamic or static depending upon whether the entry is learnt Dynamic or is added statically.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	dynamic(1), static(2)

rcIgmpCacheExtnStaticPorts		1.3.6.1.4.1.2272.1.30.12.1.2
It displays the static ports for the static joins, this would be null for the dynamic entry.
Status: current	Access: read-only
OBJECT-TYPE
	PortSet

rcIgmpSnoopTraceTable		1.3.6.1.4.1.2272.1.30.13
The table listing the multicast groups traversing the snoop enabled router
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIgmpSnoopTraceEntry

rcIgmpSnoopTraceEntry		1.3.6.1.4.1.2272.1.30.13.1
The entry listing the multicast groups traversing the snoop enabled router
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIgmpSnoopTraceEntry

rcIgmpSnoopGrpAddr		1.3.6.1.4.1.2272.1.30.13.1.1
ip mcast addr of grp traversing the router
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rcIgmpSnoopSrcAddr		1.3.6.1.4.1.2272.1.30.13.1.2
Ip src addr of the mcast grp address
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rcIgmpSnoopOutVlan		1.3.6.1.4.1.2272.1.30.13.1.3
Egress vlan id for the mcast group
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

rcIgmpSnoopInPort		1.3.6.1.4.1.2272.1.30.13.1.4
Ingress port for the mcast grp
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcIgmpSnoopInVlan		1.3.6.1.4.1.2272.1.30.13.1.5
Ingress vlan id for the mcast source
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcIgmpSnoopOutPort		1.3.6.1.4.1.2272.1.30.13.1.6
Egress port of the mcast grp
Status: current	Access: read-only
OBJECT-TYPE
	PortSet

rcIgmpNewGroupTable		1.3.6.1.4.1.2272.1.30.14
The (conceptual) table listing the multicast groups configured in the device.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIgmpNewGroupEntry

rcIgmpNewGroupEntry		1.3.6.1.4.1.2272.1.30.14.1
An entry (conceptual row) representing an Igmp group.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIgmpNewGroupEntry

rcIgmpNewGroupIpAddress		1.3.6.1.4.1.2272.1.30.14.1.1
Multicast group Address (Class D) that others want to join. A group address can be the same for many incoming ports.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rcIgmpNewGroupMembers		1.3.6.1.4.1.2272.1.30.14.1.2
IP Address of a source that has sent group report wishing to join this group.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rcIgmpNewGroupInPort		1.3.6.1.4.1.2272.1.30.14.1.3
An unique value to identify a physical interface or a logical interface (VLAN), which has received Group reports from various sources.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..65535

rcIgmpNewGroupExpiration		1.3.6.1.4.1.2272.1.30.14.1.4
Time left before the group report expired on this port. Only one of this variable port. This variable is updated upon receiving a group report.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIgmpNewGroupIfIndex		1.3.6.1.4.1.2272.1.30.14.1.5
An unique value to identify a physical interface or a logical interface (VLAN), which has received Group reports from various sources.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcIgmpNewGroupUserId		1.3.6.1.4.1.2272.1.30.14.1.6
User-id sending this group
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..32)

rcIgmpNewGroupMemberState		1.3.6.1.4.1.2272.1.30.14.1.7
Used for IGAP, to indicated member state.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	noState(1), auth(2), accStart(3), authAndAcctStart(4), authAndAcctDisabled(5)

rcIgmpNewGroupSessionTime		1.3.6.1.4.1.2272.1.30.14.1.8
Used for IGAP, to indicated the session time in seconds for the member. Session time is started after traffic is available to member. It can be also called AccountingTime since its values correspondes to the accounting duration of IGAP user session.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIgmpMvrGroupTable		1.3.6.1.4.1.2272.1.30.17
The (conceptual) table listing the mcast-vlan-registration groups.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIgmpMvrGroupEntry

rcIgmpMvrGroupEntry		1.3.6.1.4.1.2272.1.30.17.1
An entry (conceptual row) in the rcIgmpMvrGroupTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIgmpMvrGroupEntry

rcIgmpMvrGroupGroupAddress		1.3.6.1.4.1.2272.1.30.17.1.1
The group's multicast ip address.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rcIgmpMvrGroupVlanId		1.3.6.1.4.1.2272.1.30.17.1.2
The igmp snoop enabled vlan this group belongs to.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

rcIgmpMvrGroupIgmpVersion		1.3.6.1.4.1.2272.1.30.17.1.3
Version of this group.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIgmpMvrGroupLivingTime		1.3.6.1.4.1.2272.1.30.17.1.4
Living time of this group.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIgmpMvrVlanTable		1.3.6.1.4.1.2272.1.30.18
The (conceptual) table listing the mcast vlans in mcast-vlan-registration.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIgmpMvrVlanEntry

rcIgmpMvrVlanEntry		1.3.6.1.4.1.2272.1.30.18.1
An entry (conceptual row) in the rcIgmpMvrVlanTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIgmpMvrVlanEntry

rcIgmpMvrVlanMvrVlanId		1.3.6.1.4.1.2272.1.30.18.1.1
The id of mcast-vlan.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

rcIgmpMvrVlanMvrVlanProxy		1.3.6.1.4.1.2272.1.30.18.1.2
working mode of this mcast-vlan, proxy or not.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcIgmpMvrVlanSourcePort		1.3.6.1.4.1.2272.1.30.18.1.3
source port for this mcast-vlan.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIgmpMvrVlanSourceAddress		1.3.6.1.4.1.2272.1.30.18.1.4
querier address for the source in this mcast-vlan.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIgmpMvrReceiverTable		1.3.6.1.4.1.2272.1.30.19
The (conceptual) table listing the mcast vlans and receiver vlans in mcast-vlan-registration.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIgmpMvrReceiverEntry

rcIgmpMvrReceiverEntry		1.3.6.1.4.1.2272.1.30.19.1
An entry (conceptual row) in the rcIgmpMvrGroupTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIgmpMvrReceiverEntry

rcIgmpMvrReceiverVlanId		1.3.6.1.4.1.2272.1.30.19.1.1
The id of receiver vlan that bound to mcast-vlan.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

rcIgmpMvrReceiverRowStatus		1.3.6.1.4.1.2272.1.30.19.1.2
Used to create/delete entries.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcIgmpGenerateTrap		1.3.6.1.4.1.2272.1.30.11.2
Enabling the IGMP to generate trap.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIgmpGenerateLog		1.3.6.1.4.1.2272.1.30.11.3
Enabling the IGMP to generate log.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIgmpMvr		1.3.6.1.4.1.2272.1.30.11.4
Enabling mcast-vlan-registration globally.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcPlugOptModTable		1.3.6.1.4.1.2272.1.71.1
Gibc SFF diagnostic info table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPlugOptModEntry

rcPlugOptModEntry		1.3.6.1.4.1.2272.1.71.1.1
Entry containing info. for a particular port
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPlugOptModEntry

rcPlugOptModPortIndex		1.3.6.1.4.1.2272.1.71.1.1.1
An index value that uniquely identifies a port on a blade or line-card.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

rcPlugOptModDdmStatusMask		1.3.6.1.4.1.2272.1.71.1.1.2
Each bit other than ddm-ok represents a specific error. Any combination of error bits is allowed.
Status: current	Access: read-only
OBJECT-TYPE
	BITS	ddm-ok(0), ddm-checksum-error(1), ddm-i2c-read-error(2), ddm-threshold-error(3), ddm-calibration-error(4)

rcPlugOptModCalibration		1.3.6.1.4.1.2272.1.71.1.1.3
The identifier value indicates type of calibration.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	internal(1), external(2)

rcPlugOptModPowerMeasure		1.3.6.1.4.1.2272.1.71.1.1.4
The identifier value indicates type of external power.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	omi(1), average(2)

rcPlugOptModConnectorType		1.3.6.1.4.1.2272.1.71.1.1.5
The connector type is a 16 character field that contains ASCII characters, left-aligned and padded on the right with ASCII spaces. This is an assigned name that indicates some characteristic of the layer-1 interface.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(17)

rcPlugOptModVendorName		1.3.6.1.4.1.2272.1.71.1.1.6
The vendor name is a 16 character field that contains ASCII characters, left-aligned and padded on the right with ASCII spaces. The vendor name shall be the full name of the corporation, a commonly accepted abbreviation of the name, the SCSI company code, or the stock exchange code for the corporation.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(17)

rcPlugOptModVendorPartNumber		1.3.6.1.4.1.2272.1.71.1.1.7
The vendor part number is a 16 byte field that contains ASCII characters, left-aligned and padded on the right with ASCII spaces, defining the vendor part number or product name.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(17)

rcPlugOptModVendorRevNumber		1.3.6.1.4.1.2272.1.71.1.1.8
The vendor revision number is a 4-byte field that contains ASCII characters, left-aligned and padded on the right with ASCII spaces, defining the vendor product revision number.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(5)

rcPlugOptModVendorSN		1.3.6.1.4.1.2272.1.71.1.1.9
The vendor serial number is a 16 character field that contains ASCII characters, left-aligned and padded on the right with ASCII spaces, defining the vendor serial number for the transceiver.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(17)

rcPlugOptModVendorDateCode		1.3.6.1.4.1.2272.1.71.1.1.10
The date code is an 8-byte field that contains the vendor's date code in ASCII. This field is mandatory and takes the form: YYMMDDLC where YY is the 2 low order digits of the year (00=2000), MM is the month, 01 thru 12, DD is the day, 01 thru 31, and LC is an optional vendor specific lot code.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(9)

rcPlugOptModPEC		1.3.6.1.4.1.2272.1.71.1.1.11
This is a 16 byte left-justified ASCII field that records the Nortel Product Equipment Code order number for the module. Nortel part numbers are 9 bytes long, so the 10th through 16th byte should be NULL.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(17)

rcPlugOptModCLEI		1.3.6.1.4.1.2272.1.71.1.1.12
This is a 10 byte left-justified ASCII field that records the Nortel supplied Common Language Equipment Identifier code for the device. The CLEI code is a Telcordia human-readable representation of the 1D barcode.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(11)

rcPlugOptModSupportsDDM		1.3.6.1.4.1.2272.1.71.1.1.13
This boolean indicates whether or not the device supports the DDM capability.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcPlugOptModAux1Monitoring		1.3.6.1.4.1.2272.1.71.1.1.14
This value tells what Aux1 is measuring.The values are as follows: 0 Auxiliary monitoring not implemented 1 APD Bias Voltage mV (units of 10 mV) 2 Reserved 3 TEC Current (mA) 4 Laser Temperature 5 Laser Wavelength 6 +5V Supply Voltage 7 +3.3V Supply Voltage 8 +1.8V Supply Voltage 9 -5.2V Supply Voltage 10 +5.0V Supply Current (unit of 100 uA) 13 +3.3V Supply Current (unit of 100 uA) 14 +1.8V Supply Current (unit of 100 uA) 15 -5.2V Supply Current (unit of 100 uA)
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..15

rcPlugOptModAux2Monitoring		1.3.6.1.4.1.2272.1.71.1.1.15
This value tells you what AUX2 is measuring.The values are as follows: 0 Auxiliary monitoring not implemented 1 APD Bias Voltage mV (units of 10 mV) 2 Reserved 3 TEC Current (mA) 4 Laser Temperature 5 Laser Wavelength 6 +5V Supply Voltage 7 +3.3V Supply Voltage 8 +1.8V Supply Voltage 9 -5.2V Supply Voltage 10 +5.0V Supply Current (unit of 100 uA) 13 +3.3V Supply Current (unit of 100 uA) 14 +1.8V Supply Current (unit of 100 uA) 15 -5.2V Supply Current (unit of 100 uA)
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..15

rcPlugOptModWaveLength		1.3.6.1.4.1.2272.1.71.1.1.16
Nominal transmitter output wavelength at room temperature. It is expressed in nano-meters.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..65535

rcPlugOptModTemperature		1.3.6.1.4.1.2272.1.71.1.1.17
This value represents the internally measured module temperature. It is expressed in units of 1/256 of a degree Celsius and can range from -40C to +125C with 0.0001 accuracy.The most significant byte is the signed integer part of the number and the least significant byte is the fraction.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPlugOptModTemperatureHighAlarmThreshold		1.3.6.1.4.1.2272.1.71.1.1.18
This value represents the vendor specified high temperature threshold. If the device temperature exceeds this value, a temperature high is asserted. It is expressed in the same units as the measured temperature.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPlugOptModTemperatureLowAlarmThreshold		1.3.6.1.4.1.2272.1.71.1.1.19
This value represents the vendor specified low temperature threshold. If the device temperature falls below this value, a temperature low is asserted. It is expressed in the same units as the measured temperature.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPlugOptModTemperatureHighWarningThreshold		1.3.6.1.4.1.2272.1.71.1.1.20
This value represents the vendor specified high temperature warning threshold. If the device temperature exceeds this value, a temperature high warning is asserted. It is expressed in the same units as the measured temperature.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPlugOptModTemperatureLowWarningThreshold		1.3.6.1.4.1.2272.1.71.1.1.21
This value represents the vendor specified low temperature warning threshold. If the device temperature falls below this value, a temperature low warning is asserted. It is expressed in the same units as the measured temperature.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPlugOptModVoltage		1.3.6.1.4.1.2272.1.71.1.1.22
This value represents the internally measured supply voltage. It is a positive number expressed in microvolts and can range from 0 to 65535 mV.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPlugOptModVoltageHighAlarmThreshold		1.3.6.1.4.1.2272.1.71.1.1.23
This value represents the vendor specified high voltage threshold. If the measured voltage exceeds this value, a high voltage is asserted. It is a positive number expressed in microvolts.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPlugOptModVoltageLowAlarmThreshold		1.3.6.1.4.1.2272.1.71.1.1.24
This value represents the vendor specified low voltage threshold. If the measured voltage falls below this value, a low voltage is asserted. It is a positive number expressed in microvolts.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPlugOptModVoltageHighWarningThreshold		1.3.6.1.4.1.2272.1.71.1.1.25
This value represents the vendor specified high voltage warning threshold. If the measured voltage exceeds this value, a high voltage warning is asserted. It is a positive number expressed in microvolts.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPlugOptModVoltageLowWarningThreshold		1.3.6.1.4.1.2272.1.71.1.1.26
This value represents the vendor specified low voltage warning threshold. If the measured voltage falls below this value, a low voltage warning is asserted. It is a positive number expressed in microvolts.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPlugOptModBias		1.3.6.1.4.1.2272.1.71.1.1.27
This value represents the internally measured transmitter laser bias current. It is a positive number expressed in units of 2 microamps and can range from 0 to 131 mA with 0.0001 accuracy.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPlugOptModBiasHighAlarmThreshold		1.3.6.1.4.1.2272.1.71.1.1.28
This value represents the vendor specified high current threshold. If the measured bias current exceeds this value, a high current alarm is asserted. It is a positive number expressed in units of 2 microamps and can range from 0 to 131 mA with 0.0001 accuracy.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPlugOptModBiasLowAlarmThreshold		1.3.6.1.4.1.2272.1.71.1.1.29
This value represents the vendor specified low current threshold. If the measured bias current falls below this value, a low current is asserted. It is a positive number expressed in units of 2 microamps and can range from 0 to 131 mA with 0.0001 accuracy.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPlugOptModBiasHighWarningThreshold		1.3.6.1.4.1.2272.1.71.1.1.30
This value represents the vendor specified high current warning threshold. If the measured bias current exceeds this value, a high current warning is asserted. It is a positive number expressed in units of 2 microamps and can range from 0 to 131 mA with 0.0001 accuracy.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPlugOptModBiasLowWarningThreshold		1.3.6.1.4.1.2272.1.71.1.1.31
This value represents the vendor specified low current warning threshold. If the measured bias current falls below this value, a low current warning is asserted. It is a positive number expressed in units of 2 microamps and can range from 0 to 131 mA with 0.0001 accuracy.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPlugOptModTxPower		1.3.6.1.4.1.2272.1.71.1.1.32
This value represents the internally measured coupled TX output power. It is a positive number expressed in units of micro watts and can range from 0 to 65.535 mW (-40 to 18.16 dBm).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPlugOptModTxPowerHighAlarmThreshold		1.3.6.1.4.1.2272.1.71.1.1.33
This value represents the vendor specified high transmit power threshold. If the measured transmitter power exceeds this value, a transmitter power high is asserted. It is a positive number expressed in units of micro watts and can range from 0 to 65.535 mW (-40 to 18.16 dBm).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPlugOptModTxPowerLowAlarmThreshold		1.3.6.1.4.1.2272.1.71.1.1.34
This value represents the vendor specified low transmit power threshold. If the measured transmitter power falls below this value, a transmitter power low is asserted. It is a positive number expressed in units of micro watts and can range from 0 to 65.535 mW (-40 to 18.16 dBm).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPlugOptModTxPowerHighWarningThreshold		1.3.6.1.4.1.2272.1.71.1.1.35
This value represents the vendor specified high transmit power warning threshold. If the measured transmitter power exceeds this value, a transmitter power high warning is asserted. It is a positive number expressed in units of units of micro watts and can range from 0 to 65.535 mW (-40 to 18.16 dBm).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPlugOptModTxPowerLowWarningThreshold		1.3.6.1.4.1.2272.1.71.1.1.36
This value represents the vendor specified low transmit power warning threshold. If the measured transmitter power falls below this value, a transmitter power low warning is asserted. It is a positive number expressed in units of micro watts and can range from 0 to 65.535 mW (-40 to 18.16 dBm).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPlugOptModRxPower		1.3.6.1.4.1.2272.1.71.1.1.37
This value represents the internally measured received power. It is a positive number expressed in units of micro watts and can range from 0 to 65.535 mW (-40 to 18.16 dBm).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPlugOptModRxPowerHighAlarmThreshold		1.3.6.1.4.1.2272.1.71.1.1.38
This value represents the vendor specified high receiver power threshold. If the measured received power exceeds this value, a receiver power high is asserted. It is a positive number expressed in units of micro watts and can range from 0 to 65.535 mW (-40 to 18.16 dBm).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPlugOptModRxPowerLowAlarmThreshold		1.3.6.1.4.1.2272.1.71.1.1.39
This value represents the vendor specified low receiver power threshold. If the measured received power falls below this value, a receiver power low is asserted. It is a positive number expressed in units of micro watts and can range from 0 to 65.535 mW (-40 to 18.16 dBm).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPlugOptModRxPowerHighWarningThreshold		1.3.6.1.4.1.2272.1.71.1.1.40
This value represents the vendor specified high receiver power warning threshold. If the measured received power exceeds this value, a receiver power high warning is asserted. It is a positive number expressed in units of units of micro watts and can range from 0 to 65.535 uW (-40 to 18.16 dBm).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPlugOptModRxPowerLowWarningThreshold		1.3.6.1.4.1.2272.1.71.1.1.41
This value represents the vendor specified low receiver power warning threshold. If the measured received power falls below this value, a receiver power low warning is asserted. It is a positive number expressed in units of units of micro watts and can range from 0 to 65.535 mW (-40 to 18.16 dBm).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPlugOptModAux1		1.3.6.1.4.1.2272.1.71.1.1.42
This represents the internally measured A/D value specified.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPlugOptModAux1HighAlarmThreshold		1.3.6.1.4.1.2272.1.71.1.1.43
This value represents the vendor specified high Aux1 threshold.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPlugOptModAux1LowAlarmThreshold		1.3.6.1.4.1.2272.1.71.1.1.44
This value represents the vendor specified low Aux1 threshold.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPlugOptModAux1HighWarningThreshold		1.3.6.1.4.1.2272.1.71.1.1.45
This value represents the vendor specified high Aux1 warning threshold.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPlugOptModAux1LowWarningThreshold		1.3.6.1.4.1.2272.1.71.1.1.46
This value represents the vendor specified low Aux1 warning threshold.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPlugOptModAux2		1.3.6.1.4.1.2272.1.71.1.1.47
This represents the internally measured A/D value specified.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPlugOptModAux2HighAlarmThreshold		1.3.6.1.4.1.2272.1.71.1.1.48
This value represents the vendor specified high Aux1 threshold.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPlugOptModAux2LowAlarmThreshold		1.3.6.1.4.1.2272.1.71.1.1.49
This value represents the vendor specified low Aux1 threshold.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPlugOptModAux2HighWarningThreshold		1.3.6.1.4.1.2272.1.71.1.1.50
This value represents the vendor specified high Aux1 warning threshold.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPlugOptModAux2LowWarningThreshold		1.3.6.1.4.1.2272.1.71.1.1.51
This value represents the vendor specified low Aux1 warning threshold.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPlugOptModTemperatureStatus		1.3.6.1.4.1.2272.1.71.1.1.52
Used to indicate the current temperature status
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	normal(1), highWarning(2), highAlarm(3), lowWarning(4), lowAlarm(5)

rcPlugOptModVoltageStatus		1.3.6.1.4.1.2272.1.71.1.1.53
Used to indicate the current voltage status
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	normal(1), highWarning(2), highAlarm(3), lowWarning(4), lowAlarm(5)

rcPlugOptModBiasStatus		1.3.6.1.4.1.2272.1.71.1.1.54
Used to indicate the current laser bias status
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	normal(1), highWarning(2), highAlarm(3), lowWarning(4), lowAlarm(5)

rcPlugOptModTxPowerStatus		1.3.6.1.4.1.2272.1.71.1.1.55
Used to indicate the current transmitter power status
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	normal(1), highWarning(2), highAlarm(3), lowWarning(4), lowAlarm(5)

rcPlugOptModRxPowerStatus		1.3.6.1.4.1.2272.1.71.1.1.56
Used to indicate the current receiver power status
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	normal(1), highWarning(2), highAlarm(3), lowWarning(4), lowAlarm(5)

rcPlugOptModAux1Status		1.3.6.1.4.1.2272.1.71.1.1.57
Used to indicate the current Aux1 status
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	normal(1), highWarning(2), highAlarm(3), lowWarning(4), lowAlarm(5)

rcPlugOptModAux2Status		1.3.6.1.4.1.2272.1.71.1.1.58
Used to indicate the current Aux2 status
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	normal(1), highWarning(2), highAlarm(3), lowWarning(4), lowAlarm(5)

rcPlugOptModScalars		1.3.6.1.4.1.2272.1.71.2
OBJECT IDENTIFIER

rcPlugOptModDdmMonitor		1.3.6.1.4.1.2272.1.71.2.1
Enable/disable the global polling monitor for DDM
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcPlugOptModDdmMonitorInterval		1.3.6.1.4.1.2272.1.71.2.2
Indicate the interval in which the DDM alert registers is polled
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	5..60

rcPlugOptModDdmTrapSend		1.3.6.1.4.1.2272.1.71.2.3
Enable/disable the global ddm trap send to SNMP manager
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcPlugOptModDdmAlarmPortdown		1.3.6.1.4.1.2272.1.71.2.4
Enable/disable the global portdown option when ddm alarm occurs
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcVrrpMib		1.3.6.1.4.1.2272.1.73.1
OBJECT IDENTIFIER

rcVrrpObjects		1.3.6.1.4.1.2272.1.73.1.1
OBJECT IDENTIFIER

rcVrrpNotifications		1.3.6.1.4.1.2272.1.73.1.2
OBJECT IDENTIFIER

rcVrrpScalars		1.3.6.1.4.1.2272.1.73.1.1.1
OBJECT IDENTIFIER

rcVrrpPingVirtualAddrEnable		1.3.6.1.4.1.2272.1.73.1.1.1.1
Used to configure whether this device should respond to pings directed to a virtual router's IP address.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcVrrpTrapStateTransitionType		1.3.6.1.4.1.2272.1.73.1.1.1.2
Potential types of state transitions. Used by rcVrrpTrapStateTransition trap.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), masterToBackup(2), backupToMaster(3), initializeToMaster(4), masterToInitialize(5), initializeToBackup(6), backupToInitialize(7)

rcVrrpTrapStateTransitionCause		1.3.6.1.4.1.2272.1.73.1.1.1.3
Potential types of causes that will generate a rcVrrpTrapStateTransition trap.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), higherPriorityAdvertizeReceived(2), shutdownReceived(3), rcVrrpAddrAndPhysicalAddrMatch(4), masterDownInterval(5), preempted(6)

rcVrrpOperTable		1.3.6.1.4.1.2272.1.73.1.1.2
Operations table for a VRRP router which consists of a sequence (i.e., one or more conceptual rows) of 'rcVrrpOperEntry' items.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcVrrpOperEntry

rcVrrpOperEntry		1.3.6.1.4.1.2272.1.73.1.1.2.1
An entry in the rcVrrpOperTable containing the operational characteristics of a virtual router. On a VRRP router, a given virtual router is identified by a combination of the IF index and VRID.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcVrrpOperEntry

rcVrrpOperIfIndex		1.3.6.1.4.1.2272.1.73.1.1.2.1.1
port interface index.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndexOrZero

rcVrrpOperVrId		1.3.6.1.4.1.2272.1.73.1.1.2.1.2
This object contains the Virtual Router Identifier (VRID).
Status: current	Access: read-only
OBJECT-TYPE
	VrId

rcVrrpOperIpAddr		1.3.6.1.4.1.2272.1.73.1.1.2.1.3
The assigned IP addresses that a virtual router is responsible for backing up.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcVrrpOperVirtualMacAddr		1.3.6.1.4.1.2272.1.73.1.1.2.1.4
The virtual MAC address of the virtual router. This is derived as follows: 00-00-5E-00-01-. Where the first three octets consist of the IANA's OUI; The next two octets indicate the address block of the VRRP protocol; and the remaining octets consist of the VRID. Although this object can be derived from the 'rcVrrpOperVrId' object, it is included here, for completeness, so that it is easily obtainable by a management application and can be included in VRRP-related SNMP traps.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rcVrrpOperState		1.3.6.1.4.1.2272.1.73.1.1.2.1.5
The current state of the virtual router.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	initialize(1), backup(2), master(3)

rcVrrpOperControl		1.3.6.1.4.1.2272.1.73.1.1.2.1.6
This object will enable/disable the virtual router function. Setting the value to 'enabled', will transition the state of the router from 'initialize to 'backup'; Setting the value to 'disabled', will tranisition the router from 'master' or 'backup' to 'initialize'.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

rcVrrpOperPriority		1.3.6.1.4.1.2272.1.73.1.1.2.1.7
This object specifies the priority for the virtual router (e.g., master election) with respect to other virtual routers that are backing up a one or more associated IP addresses. Higher values imply higher priority. A priority of '0', although not settable, is used to indicate that this router has ceased to particpate in VRRP and a backup virtual router should transition \ to become a new master. A priority of 255 is used for the router that owns the associated IP address(es).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..255

rcVrrpOperIpAddrCount		1.3.6.1.4.1.2272.1.73.1.1.2.1.8
The number of IP addresses that are associated with this virtual router. This number is equal to the number of rows in the vrrpAssoIpAddrTable that correspond to a given IF index/VRID pair.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

rcVrrpOperMasterIpAddr		1.3.6.1.4.1.2272.1.73.1.1.2.1.9
The master router's real (primary) IP address. This is the IP address listed as the source in VRRP advertisement last received by this virtual router
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcVrrpOperAuthType		1.3.6.1.4.1.2272.1.73.1.1.2.1.10
Authentication type used for VRRP protocol exchanges between virtual routers.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noAuthentication(1), simpleTextPassword(2), ipAuthenticationHeader(3)

rcVrrpOperAuthKey		1.3.6.1.4.1.2272.1.73.1.1.2.1.11
The Authentication Key. If the virtual router's Authorization Type is 'simpleTextPassword', and the key length is shorter than 8 octets, the agent will left adjust and zero fill to 8 octets. When read, rcVrrpOperAuthKey always returns an Octet String of length zero.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(8)

rcVrrpOperHMACMD5Key		1.3.6.1.4.1.2272.1.73.1.1.2.1.12
The Authentication Key. If the virtual router's 'Authorization Type' is 'ipAuthenticationHeader', and the key length is shorter than 16 octets, the agent will left adjust and zero fill to 16 octets. When read, rcVrrpOperHMACMD5Key always returns an Octet String of length zero.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(16)

rcVrrpOperAdvertisementInterval		1.3.6.1.4.1.2272.1.73.1.1.2.1.13
This is the time interval, in seconds, between sending advertisement messages. Only the master router sends VRRP advertisements.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..255

rcVrrpOperPreemptMode		1.3.6.1.4.1.2272.1.73.1.1.2.1.14
Controls whether a higher priority virtual router will preempt a lower priority master.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	true(1), false(2)

rcVrrpOperVirtualRouterUpTime		1.3.6.1.4.1.2272.1.73.1.1.2.1.15
This is the time interval (in hundredths of a second) since this virtual router was initialized.
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

rcVrrpOperRowStatus		1.3.6.1.4.1.2272.1.73.1.1.2.1.16
The row status variable, used according to installation and removal conventions for conceptual rows. Setting this object to 'createAndGo' results in enabling the VRRP protocol for this virtual router. The information required to actually create the conceptual row may be included in the SET primitive or may be initialized by the agent on the virtual router. Destroying the entry or setting it to 'notInService' disables VRRP on this virtual router.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcVrrpOperCriticalIpAddr		1.3.6.1.4.1.2272.1.73.1.1.2.1.17
IP address of the interface that will cause a shutdown event.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcVrrpOperHoldDownTimer		1.3.6.1.4.1.2272.1.73.1.1.2.1.18
Used to configure the amount of time (in seconds) to wait before preempting the current vrrp master.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..21600

rcVrrpOperHoldDownState		1.3.6.1.4.1.2272.1.73.1.1.2.1.19
Used to indicate the hold-down state of this vrrp interface. If the hold-down timer is operational this variable will be set to 'active'. 'dormant' otherwise.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	dormant(1), active(2)

rcVrrpOperHoldDownTimeRemaining		1.3.6.1.4.1.2272.1.73.1.1.2.1.20
Used to indicate the amount of time (in seconds) left before the rcVrrpOperHoldDownTimer will expire.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..21600

rcVrrpOperAction		1.3.6.1.4.1.2272.1.73.1.1.2.1.21
Used to trigger an action on this vrrp interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), preemptHoldDownTimer(2)

rcVrrpOperCriticalIpAddrEnable		1.3.6.1.4.1.2272.1.73.1.1.2.1.22
Indicate if an user-defined critical IP address should be enabled. 'NO' = use the default IP address (0.0.0.0). No effect if an user-defined IP address does not exist.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcVrrpOperBackUpMaster		1.3.6.1.4.1.2272.1.73.1.1.2.1.23
Enable the backup VRRP switch traffic forwarding. This will reduce the traffic in IST link in the time of SMLT.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

rcVrrpOperBackUpMasterState		1.3.6.1.4.1.2272.1.73.1.1.2.1.24
Indicate whether backup VRRP switch traffic forwarding is enabled or not.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2)

rcVrrpOperFasterAdvInterval		1.3.6.1.4.1.2272.1.73.1.1.2.1.25
This is the faster advertisement interval, in milliseconds, between sending advertisement messages. When the faster advertisement interval enable is checked, the faster advertisement interval is being used instead of the regular advertisement interval
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	200..1000

rcVrrpOperFasterAdvIntervalEnable		1.3.6.1.4.1.2272.1.73.1.1.2.1.26
Used to indicate if the Faster Advertisement Interval should be used. 'Disable' means use regular Advertisement interval.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

rcVrrpTrapStateTransition		1.3.6.1.4.1.2272.1.73.1.2.1
A rcVrrpTrapStateTransition trap signifies a state transition has occurred on a particular vrrp interface. Implementation of this trap is optional.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcVrrpRouterStatsTable		1.3.6.1.4.1.2272.1.73.1.1.3
Table of virtual router statistics.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcVrrpRouterStatsEntry

rcVrrpRouterStatsEntry		1.3.6.1.4.1.2272.1.73.1.1.3.1
An entry in the table, containing statistics information about a given virtual router.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcVrrpRouterStatsEntry

rcVrrpStatsIfIndex		1.3.6.1.4.1.2272.1.73.1.1.3.1.1
port interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcVrrpStatsVrId		1.3.6.1.4.1.2272.1.73.1.1.3.1.2
This object contains the Virtual Router Identifier (VRID).
Status: current	Access: read-only
OBJECT-TYPE
	VrId

rcVrrpStatsBecomeMaster		1.3.6.1.4.1.2272.1.73.1.1.3.1.3
The total number of times that this virtual router's state has transitioned from BACKUP to MASTER.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcVrrpStatsAdvertiseRcvd		1.3.6.1.4.1.2272.1.73.1.1.3.1.4
The total number of VRRP advertisements received by this virtual router.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcVrrpStatsAdvertiseIntervalErrors		1.3.6.1.4.1.2272.1.73.1.1.3.1.5
The total number of VRRP advertisement packets received for which the advertisement interval is different than the one configured for the local virtual router.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcVrrpStatsPasswdSecurityViolations		1.3.6.1.4.1.2272.1.73.1.1.3.1.6
The total number of VRRP packets received that do not pass the simple text password authentification check.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcVrrpStatsHmacSecurityViolations		1.3.6.1.4.1.2272.1.73.1.1.3.1.7
The total number of VRRP packets received that do not pass the HMAC-MD5-96 authentification check.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcVrrpStatsIpTtlErrors		1.3.6.1.4.1.2272.1.73.1.1.3.1.8
The total number of VRRP packets received by the virtual router with IP TTL (Time-To-Live) not equal to 255.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcVrrpStatsPriorityZeroPktsRcvd		1.3.6.1.4.1.2272.1.73.1.1.3.1.9
The total number of VRRP packets received by the virtual router with a priority of '0'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcVrrpStatsPriorityZeroPktsSent		1.3.6.1.4.1.2272.1.73.1.1.3.1.10
The total number of VRRP packets sent by the virtual router with a priority of '0'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcVrrpStatsInvalidTypePktsRcvd		1.3.6.1.4.1.2272.1.73.1.1.3.1.11
The number of VRRP packets received by the virtual router with an invalid value in the 'type' field.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcVrrpStatsAddressListErrors		1.3.6.1.4.1.2272.1.73.1.1.3.1.12
Packets received address list the address list does not match the locally configured list for the virtual router.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcVrrpStatsUnknownAuthType		1.3.6.1.4.1.2272.1.73.1.1.3.1.13
Packets received with an unknown authentication type.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcVrrpStatsAuthTypeErrors		1.3.6.1.4.1.2272.1.73.1.1.3.1.14
Packets received with 'Auth Type' not equal to the locally configured authentication method ('vrrpOperAuthType').
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcUserSetTimeYear		1.3.6.1.4.1.2272.1.31.1
Year of the time.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1998..2097

rcUserSetTimeMonth		1.3.6.1.4.1.2272.1.31.2
Month of the time.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..12

rcUserSetTimeDate		1.3.6.1.4.1.2272.1.31.3
Date of the time.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..31

rcUserSetTimeHour		1.3.6.1.4.1.2272.1.31.4
Hour of the time.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..23

rcUserSetTimeMinute		1.3.6.1.4.1.2272.1.31.5
Minute of the time.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..59

rcUserSetTimeSecond		1.3.6.1.4.1.2272.1.31.6
Second of the time.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..59

rcL2RedundancyHaCpuState		1.3.6.1.4.1.2272.1.32.1
Indicate the Ha-CPU state. initialization - indicate the CPU is in this state. oneWayActive - Modules that need to be synchronized have registered with the framework (either locally or a message was received from remote CPU (1). twoWayActive - Modules that need to be synchronized have registered with the framework (either locally or a message was received from remote CPU (2). synchronized - Table based synchroniztion was completed on the current CPU (3). remoteIncompatible - CPUs framework version is incompatible with the remote CPU (4). error - If an invalid event is generated in a given state the CPU enters Error state (5). disabled - High Availability is not enabled (6). peerNotConnected - no peer connection is established (7). peerConnected - peer connection is established (8). lostPeerConnection - lost connection to peer/Standby CPU (9). notSynchronized - Table Sync is not complete (10).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	initialization(0), oneWayActive(1), twoWayActive(2), synchronized(3), remoteIncompatible(4), error(5), disabled(6), peerNotConnected(7), peerConnected(8), lostPeerConnection(9), notSynchronized(10)

rcL2RedundancyHaEvent		1.3.6.1.4.1.2272.1.32.2
Indicate the Ha event status. restart (0) - Causes the state machine to restart systemRegistrationDone (1)- Causes the CPU to transfer to One Way or Two Way Active state. Locally or message received from remote CPU. tableSynchronizationDone (2) - Causes the CPU to transfer to Synchronized state. versionIncompatible (3) - Causes the CPU to go to Remote Incompatible state noEvent (4) - Means no event has occured uptill now.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	restart(0), systemRegistrationDone(1), tableSynchronizationDone(2), versionIncompatible(3), noEvent(4)

rcL2RedundancyEnable		1.3.6.1.4.1.2272.1.32.3
Indicate the feature enable/disable.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcL2RedundancyStandbyCpu		1.3.6.1.4.1.2272.1.32.4
Indicate if the L2 Redundancy is enabled on the standby CPU.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	hotStandbyCPU(1), warmStandbyCPU(2), standbyCPUNotPresent(3)

rcNtpGlobal		1.3.6.1.4.1.2272.1.33.1
OBJECT IDENTIFIER

rcNtpGlobalEnable		1.3.6.1.4.1.2272.1.33.1.1
Enable/disable NTP feature
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcNtpGlobalInterval		1.3.6.1.4.1.2272.1.33.1.2
Time interval between successive NTP updates in minutes.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	10..1440

rcNtpServerTable		1.3.6.1.4.1.2272.1.33.2
The NTP server table. This table lists the information of a NTP server
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcNtpServerEntry

rcNtpServerEntry		1.3.6.1.4.1.2272.1.33.2.1
A NTP server table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcNtpServerEntry

rcNtpServerAddress		1.3.6.1.4.1.2272.1.33.2.1.1
Server IP address of NTP time source referred to in this table entry.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcNtpServerEnable		1.3.6.1.4.1.2272.1.33.2.1.2
Enable or disable this server for participation in time update.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcNtpServerAuthentication		1.3.6.1.4.1.2272.1.33.2.1.3
Enable or disable the MD5 Authentication on this serve.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcNtpServerKeyId		1.3.6.1.4.1.2272.1.33.2.1.4
Public Key used to generate MD5 digest for this server.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..2147483647

rcNtpServerAccessAttempts		1.3.6.1.4.1.2272.1.33.2.1.5
The number of NTP requests sent to this server
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcNtpServerAccessSuccess		1.3.6.1.4.1.2272.1.33.2.1.6
The number of times this server was selected to update the time
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcNtpServerAccessFailure		1.3.6.1.4.1.2272.1.33.2.1.7
The number of times this server was rejected from updating the time
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcNtpServerRowStatus		1.3.6.1.4.1.2272.1.33.2.1.8
Used to create/delete entries.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcNtpServerStratum		1.3.6.1.4.1.2272.1.33.2.1.9
Stratum of this server
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..16)

rcNtpServerVersion		1.3.6.1.4.1.2272.1.33.2.1.10
NTP version of this server
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..16)

rcNtpServerRootDelay		1.3.6.1.4.1.2272.1.33.2.1.11
Root Delay of this server
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..32)

rcNtpServerPrecision		1.3.6.1.4.1.2272.1.33.2.1.12
NTP precision of this server in seconds
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..32)

rcNtpServerReachable		1.3.6.1.4.1.2272.1.33.2.1.13
NTP Reachability of this server
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..16)

rcNtpServerSynchronized		1.3.6.1.4.1.2272.1.33.2.1.14
Status of synchronization with this server
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..16)

rcNtpKeyTable		1.3.6.1.4.1.2272.1.33.3
The NTP key table. This table lists the private key of the public key Id
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcNtpKeyEntry

rcNtpKeyEntry		1.3.6.1.4.1.2272.1.33.3.1
A NTP key table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcNtpKeyEntry

rcNtpKeyId		1.3.6.1.4.1.2272.1.33.3.1.1
Public Key used to generate MD5 digest
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..2147483647

rcNtpKeySecret		1.3.6.1.4.1.2272.1.33.3.1.2
Private Key used to generate MD5 Digest
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..8)

rcNtpKeyRowStatus		1.3.6.1.4.1.2272.1.33.3.1.3
Used to create/delete entries.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcSvlanGlobal		1.3.6.1.4.1.2272.1.35.1
OBJECT IDENTIFIER

rcSvlanActiveLevel		1.3.6.1.4.1.2272.1.35.1.1
Stacked Vlan active level.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..7

rcSvlanTable		1.3.6.1.4.1.2272.1.35.2
A list of possible levels and their corresponding ether type. The number of entries is eight.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcSvlanEntry

rcSvlanEntry		1.3.6.1.4.1.2272.1.35.2.1
A Stacked Vlan table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcSvlanEntry

rcSvlanId		1.3.6.1.4.1.2272.1.35.2.1.1
Row Index.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..8

rcSvlanLevel		1.3.6.1.4.1.2272.1.35.2.1.2
A value that identifies the switch level associated with this entry.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcSvlanEtherType		1.3.6.1.4.1.2272.1.35.2.1.3
The ether type value is used for svlan tagging.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rc2kChassis		1.3.6.1.4.1.2272.1.100.1
OBJECT IDENTIFIER

rc2kChassisPortOperStatus		1.3.6.1.4.1.2272.1.100.1.1
A bit array that contains the oper-status of the ports in the device. 2 bits are used for each port. The high order 2 bits of the first octet represent port #0, the next two bits are used for port #1, etc. The status is encoded with the following scheme : value meaning ----- ------- 0 no-link (admin=up, oper=down) 1 up (admin=up, oper=up) 2 down (admin=down, oper=down) 3 testing (admin=test, oper=test)
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(256)

rc2kChassisTemperature		1.3.6.1.4.1.2272.1.100.1.2
Used to indicate the core operating temperature of the chassis. This value represents the degree in celsius of the air inside the chassis.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rc2kChassisAmbientLowerTemperature		1.3.6.1.4.1.2272.1.100.1.3
Used to indicate the temperature of the air entering the fan at the lower half of the chassis.
Status: obsolete	Access: read-only
OBJECT-TYPE
	Gauge32

rc2kChassisAmbientUpperTemperature		1.3.6.1.4.1.2272.1.100.1.4
Used to indicate the temperature of the air entering the fan at the upper half of the chassis.
Status: obsolete	Access: read-only
OBJECT-TYPE
	Gauge32

rc2kChassisBaseMacAddr		1.3.6.1.4.1.2272.1.100.1.5
base mac addr
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rc2kChassisMacAddrCapacity		1.3.6.1.4.1.2272.1.100.1.6
Mac Address Capacity
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rc2kCpuEthernetPortTable		1.3.6.1.4.1.2272.1.100.2
2k CPU Ethernet Port table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Rc2kCpuEthernetPortEntry

rc2kCpuEthernetPortEntry		1.3.6.1.4.1.2272.1.100.2.1
Entry containing infomation of 2k CPU Ethernet Port
Status: current	Access: not-accessible
OBJECT-TYPE
	Rc2kCpuEthernetPortEntry

rc2kCpuEthernetPortIfIndex		1.3.6.1.4.1.2272.1.100.2.1.1
IfIndex of the port.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rc2kCpuEthernetPortDescr		1.3.6.1.4.1.2272.1.100.2.1.2
Port description
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..128)

rc2kCpuEthernetPortAdminStatus		1.3.6.1.4.1.2272.1.100.2.1.3
Used to configure the admininstrative status of the port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	up(1), down(2), unknown(3)

rc2kCpuEthernetPortOperStatus		1.3.6.1.4.1.2272.1.100.2.1.4
Used to indicate the administrative status of the port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2), unknown(3)

rc2kCpuEthernetPortAddr		1.3.6.1.4.1.2272.1.100.2.1.5
Used to configure the port's IP address
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rc2kCpuEthernetPortMask		1.3.6.1.4.1.2272.1.100.2.1.6
Used to configure the port's net mask
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rc2kCpuEthernetPortGateway		1.3.6.1.4.1.2272.1.100.2.1.7
Used to configure the the IP address of the gateway that should be used to forward IP traffic.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rc2kCpuEthernetPortNetwork		1.3.6.1.4.1.2272.1.100.2.1.8
Used to configure the network that can be used to remotely manage this device.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rc2kCpuEthernetPortAutoNegotiate		1.3.6.1.4.1.2272.1.100.2.1.9
Used to configure auto-negotiation on this port.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rc2kCpuEthernetPortAdminDuplex		1.3.6.1.4.1.2272.1.100.2.1.10
Used to configure the administrative duplex setting for this port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	half(1), full(2)

rc2kCpuEthernetPortOperDuplex		1.3.6.1.4.1.2272.1.100.2.1.11
Used to indicate the operational duplex setting for this port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	half(1), full(2)

rc2kCpuEthernetPortAdminSpeed		1.3.6.1.4.1.2272.1.100.2.1.12
Used to configure the administrative speed setting for this port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), mbps10(1), mbps100(2)

rc2kCpuEthernetPortOperSpeed		1.3.6.1.4.1.2272.1.100.2.1.13
Used to indicate the operational duplex setting for this port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(0), mbps10(1), mbps100(2), mbps1000(3)

rc2kCpuEthernetPortEnableBootp		1.3.6.1.4.1.2272.1.100.2.1.14
Used to enable/disable the Bootp feature on this port.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rc2kCpuEthernetPortMgmtMacAddr		1.3.6.1.4.1.2272.1.100.2.1.15
Used to indicate the mac addr for this port.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rc2kCpuSerialPortTable		1.3.6.1.4.1.2272.1.100.3
2k CPU Serial Port table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Rc2kCpuSerialPortEntry

rc2kCpuSerialPortEntry		1.3.6.1.4.1.2272.1.100.3.1
Entry containing infomation of 2k CPU Serial Port
Status: current	Access: not-accessible
OBJECT-TYPE
	Rc2kCpuSerialPortEntry

rc2kCpuSerialPortIfIndex		1.3.6.1.4.1.2272.1.100.3.1.1
IfIndex for this port.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rc2kCpuSerialPortDescr		1.3.6.1.4.1.2272.1.100.3.1.2
Port description.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..128)

rc2kCpuSerialPortMode		1.3.6.1.4.1.2272.1.100.3.1.3
Used to configure the mode this port should operate in.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	cli(1), slip(2), ppp(3)

rc2kCpuSerialPortAdminStatus		1.3.6.1.4.1.2272.1.100.3.1.4
Used to configure the administrative status setting for this port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	up(1), down(2), unknown(3)

rc2kCpuSerialPortOperStatus		1.3.6.1.4.1.2272.1.100.3.1.5
Used to indicate the operational status setting for this port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2), unknown(3)

rc2kCpuSerialPortBaudRate		1.3.6.1.4.1.2272.1.100.3.1.6
Used to configure the baud rate of this port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	baud2400(2400), baud4800(4800), baud9600(9600), baud19200(19200), baud38400(38400), baud57600(57600), baud115200(115200)

rc2kCpuSerialPortDataBits		1.3.6.1.4.1.2272.1.100.3.1.7
Used to configure the number of data bits, per byte of data, this port should send/receive.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	seven(1), eight(2)

rc2kCpuSerialPortMyAddr		1.3.6.1.4.1.2272.1.100.3.1.8
Used to configure this port's IP address. Used for both 'slip' and 'ppp' modes.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rc2kCpuSerialPortPeerAddr		1.3.6.1.4.1.2272.1.100.3.1.9
Used to configure the peer's IP address. Used for both 'slip' and 'ppp' modes.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rc2kCpuSerialPortSlipMtu		1.3.6.1.4.1.2272.1.100.3.1.10
Used to configure the MTU for this port. Used for slip only.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..224

rc2kCpuSerialPortSlipTxRxCompress		1.3.6.1.4.1.2272.1.100.3.1.11
Used to enable/disable compression of TCP/IP packet headers on this port. Used for slip only.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rc2kCpuSerialPortSlipRxCompress		1.3.6.1.4.1.2272.1.100.3.1.12
Used to enable/disable compression for receiving packets on this port. Used for slip only.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rc2kCpuSerialPortPppConfigFile		1.3.6.1.4.1.2272.1.100.3.1.13
Used to configure the configuration file to use for PPP.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..256)

rc2kDevice		1.3.6.1.4.1.2272.1.100.4
OBJECT IDENTIFIER

rc2kDeviceGlobalTable		1.3.6.1.4.1.2272.1.100.4.1
2k CPU Ethernet Port table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Rc2kDeviceGlobalEntry

rc2kDeviceGlobalEntry		1.3.6.1.4.1.2272.1.100.4.1.1
Entry containing infomation of 2k CPU Ethernet Port
Status: current	Access: not-accessible
OBJECT-TYPE
	Rc2kDeviceGlobalEntry

rc2kDeviceGlobalSlot		1.3.6.1.4.1.2272.1.100.4.1.1.1
slot number
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	3 | 5..6

rc2kDeviceGlobalFlashBytesUsed		1.3.6.1.4.1.2272.1.100.4.1.1.2
bytes used
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rc2kDeviceGlobalFlashBytesFree		1.3.6.1.4.1.2272.1.100.4.1.1.3
bytes free
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rc2kDeviceGlobalFlashNumFiles		1.3.6.1.4.1.2272.1.100.4.1.1.4
# files in flash
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rc2kDeviceGlobalPcmciaBytesUsed		1.3.6.1.4.1.2272.1.100.4.1.1.5
bytes used
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rc2kDeviceGlobalPcmciaBytesFree		1.3.6.1.4.1.2272.1.100.4.1.1.6
bytes free
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rc2kDeviceGlobalPcmciaNumFiles		1.3.6.1.4.1.2272.1.100.4.1.1.7
# files in pcmcia
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rc2kDeviceGlobalAction		1.3.6.1.4.1.2272.1.100.4.1.1.8
none(1), resetPcmcia(2), ..
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), resetPcmcia(2), pcmciaStop(3)

rc2kDeviceGlobalResult		1.3.6.1.4.1.2272.1.100.4.1.1.9
Used to indicate the result of the last action performed on one of the system's device.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), inProgress(2), success(3), fail(4)

rc2kDeviceSeparator1		1.3.6.1.4.1.2272.1.100.4.2
This leaf is used to provide a separation between tables. No meaningful information is stored in this variable.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rc2kDeviceFlashFileTable		1.3.6.1.4.1.2272.1.100.4.3
2k Flash table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Rc2kDeviceFlashFileEntry

rc2kDeviceFlashFileEntry		1.3.6.1.4.1.2272.1.100.4.3.1
Entry containing infomation of 2k CPU Serial Port
Status: current	Access: not-accessible
OBJECT-TYPE
	Rc2kDeviceFlashFileEntry

rc2kDeviceFlashFileSlot		1.3.6.1.4.1.2272.1.100.4.3.1.1
slot number
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	3 | 5..6

rc2kDeviceFlashFileName		1.3.6.1.4.1.2272.1.100.4.3.1.2
name of file
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..114)

rc2kDeviceFlashFileDate		1.3.6.1.4.1.2272.1.100.4.3.1.3
date
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..32)

rc2kDeviceFlashFileSize		1.3.6.1.4.1.2272.1.100.4.3.1.4
size in bytes
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rc2kDevicePcmciaPresent		1.3.6.1.4.1.2272.1.100.4.4
pcmcia is a slower device. This leaf is used to stop the access into pcmcia file table when it got the end of flash file table.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rc2kDevicePcmciaFileTable		1.3.6.1.4.1.2272.1.100.4.5
2k PCMCIA table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Rc2kDevicePcmciaFileEntry

rc2kDevicePcmciaFileEntry		1.3.6.1.4.1.2272.1.100.4.5.1
Entry containing infomation of 2k CPU Serial Port
Status: current	Access: not-accessible
OBJECT-TYPE
	Rc2kDevicePcmciaFileEntry

rc2kDevicePcmciaFileSlot		1.3.6.1.4.1.2272.1.100.4.5.1.1
slot number
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	3 | 5..6

rc2kDevicePcmciaFileName		1.3.6.1.4.1.2272.1.100.4.5.1.2
name of file
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..114)

rc2kDevicePcmciaFileDate		1.3.6.1.4.1.2272.1.100.4.5.1.3
date
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..32)

rc2kDevicePcmciaFileSize		1.3.6.1.4.1.2272.1.100.4.5.1.4
size in bytes
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rc2kDeviceSeparator2		1.3.6.1.4.1.2272.1.100.4.6
This leaf is used to provide a separation between tables. No meaningful information is stored in this variable.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rc2kBootConfigTable		1.3.6.1.4.1.2272.1.100.5
2k Boot Configuration table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Rc2kBootConfigEntry

rc2kBootConfigEntry		1.3.6.1.4.1.2272.1.100.5.1
Entry containing boot configuration information.
Status: current	Access: not-accessible
OBJECT-TYPE
	Rc2kBootConfigEntry

rc2kBootConfigSlot		1.3.6.1.4.1.2272.1.100.5.1.1
slot number, tattoo use 3 as cpu slot, 4 is not valid cpu slot number
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	3..6

rc2kBootConfigLastBootConfigSource		1.3.6.1.4.1.2272.1.100.5.1.2
boot config source
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

rc2kBootConfigLastRuntimeImageSource		1.3.6.1.4.1.2272.1.100.5.1.3
runtime image source
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

rc2kBootConfigLastRuntimeConfigSource		1.3.6.1.4.1.2272.1.100.5.1.4
runtime config source
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

rc2kBootConfigPrimaryImageSource		1.3.6.1.4.1.2272.1.100.5.1.5
image source
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

rc2kBootConfigPrimaryConfigSource		1.3.6.1.4.1.2272.1.100.5.1.6
config source
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

rc2kBootConfigSecondaryImageSource		1.3.6.1.4.1.2272.1.100.5.1.7
image source
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

rc2kBootConfigSecondaryConfigSource		1.3.6.1.4.1.2272.1.100.5.1.8
config source
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

rc2kBootConfigTertiaryImageSource		1.3.6.1.4.1.2272.1.100.5.1.9
image source
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

rc2kBootConfigTertiaryConfigSource		1.3.6.1.4.1.2272.1.100.5.1.10
config source
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

rc2kBootConfigEnableAutoBoot		1.3.6.1.4.1.2272.1.100.5.1.11
auto boot mode
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rc2kBootConfigEnableFactoryDefaults		1.3.6.1.4.1.2272.1.100.5.1.12
use factory default
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rc2kBootConfigEnableDebugMode		1.3.6.1.4.1.2272.1.100.5.1.13
debug mode
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rc2kBootConfigEnableHwWatchDogTimer		1.3.6.1.4.1.2272.1.100.5.1.14
hw watch dog timer
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rc2kBootConfigEnableRebootOnError		1.3.6.1.4.1.2272.1.100.5.1.15
reboot on error
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rc2kBootConfigEnableTelnetServer		1.3.6.1.4.1.2272.1.100.5.1.16
telnet server
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rc2kBootConfigEnableRloginServer		1.3.6.1.4.1.2272.1.100.5.1.17
rlogin server
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rc2kBootConfigEnableFtpServer		1.3.6.1.4.1.2272.1.100.5.1.18
ftp server
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rc2kBootConfigEnableTftpServer		1.3.6.1.4.1.2272.1.100.5.1.19
tftp server
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rc2kBootConfigSwVersion		1.3.6.1.4.1.2272.1.100.5.1.20
current sw version
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

rc2kBootConfigMulticastConfigProfile		1.3.6.1.4.1.2272.1.100.5.1.21
multicast config
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..6

rc2kBootConfigEnableSshServer		1.3.6.1.4.1.2272.1.100.5.1.22
ssh server
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rc2kBootConfigEnableAltLed		1.3.6.1.4.1.2272.1.100.5.1.23
Boot flag for enableing Alternate LED
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rc2kBootConfigPrimaryBackupConfigSource		1.3.6.1.4.1.2272.1.100.5.1.24
primary backup config source (safeconfig)
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

rc2kBootConfigSecondaryBackupConfigSource		1.3.6.1.4.1.2272.1.100.5.1.25
secondary backup config source (safeconfig)
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

rc2kBootConfigTertiaryBackupConfigSource		1.3.6.1.4.1.2272.1.100.5.1.26
tertiary backup config source (safeconfig)
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

rc2kBootConfigEnable8616ReAutoneg		1.3.6.1.4.1.2272.1.100.5.1.27
Enable re-autoneg for 8616SX Cards (Intel GMAC fix)
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rc2kBootConfigMezzImageSource		1.3.6.1.4.1.2272.1.100.5.1.28
Mezz image source
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

rc2kBootConfigEnableMezz		1.3.6.1.4.1.2272.1.100.5.1.29
Enable/disable Mezz Flag
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rc2kBootConfigPrimaryLicenseSource		1.3.6.1.4.1.2272.1.100.5.1.30
primary license file name
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

rc2kBootConfigSecondaryLicenseSource		1.3.6.1.4.1.2272.1.100.5.1.31
secondary license file name
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

rc2kBootConfigTertiaryLicenseSource		1.3.6.1.4.1.2272.1.100.5.1.32
tertiary license file name
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

rc2kBootConfigEnableCfPcCompat		1.3.6.1.4.1.2272.1.100.5.1.44
Enable/disable CF PC compatibility flag
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rc2kCardTable		1.3.6.1.4.1.2272.1.100.6
2k Card table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Rc2kCardEntry

rc2kCardEntry		1.3.6.1.4.1.2272.1.100.6.1
Entry containing information of 2k Card
Status: current	Access: not-accessible
OBJECT-TYPE
	Rc2kCardEntry

rc2kCardIndex		1.3.6.1.4.1.2272.1.100.6.1.1
slot number.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..10

rc2kCardFrontType		1.3.6.1.4.1.2272.1.100.6.1.2
Used to indicate card types in the Accelar 8000 product families. For Accelar 8000 devices, all cards use an encoded value according to the following rule: | 6 | 1 | 5 | 4 | 1 | 3 | 4 | 8 | +------+-------+-------+-------+------------+------+------+------+ bits : |31-26 | 25 | 24-20 | 19-16 | 15 | 14-12 | 11-8 | 7-0 | +------+-------+-------+-------+----+-------+------+------+------+ field : | a | b | c | d | e | f | g | h | +------+-------+-------+-------+----+-------+------+------+------+ a : Family type/Product line (6 bits (5 bits usuable) (was 4 bits)) MSB bit31 should not be used (MIB compiler fails) 0x0-00 = 0000-00 = Reserved 0x1-00 = 0001-00 = Monoploy non specific (e.g backplane, psu, fans) 0x2-00 = 0010-00 = Boardwalk 0x2-01 = 0010-01 = Power Ranger 0x3-00 = 0011-00 = Marvin Gardens 0x4-00 = 0100-00 = Thunderbolt (was Pacific) 0x5-00 = 0101-00 = PP8300 (was ParkPlace) 0x6-00 = 0110-00 = Central Office (only used in chassis) 0x7-00 = 0111-00 = Alteon WebSystems b : Interface / Device type variation: 1 bit (was 3 bits, 2 bits were stolen by faimly) MSB bit31 should not be used (MIB compiler fails) 0x0-00 = 0000-00 = Reserved 0x1-00 = 0001-00 = Monoploy non specific (e.g backplane, psu, fans) 0x2-00 = 0010-00 = Boardwalk 0x2-01 = 0010-01 = Power Ranger 0x3-00 = 0011-00 = Marvin Gardens 0x4-00 = 0100-00 = Thunderbolt (was Pacific) 0x5-00 = 0101-00 = PP8300 (was ParkPlace) 0x6-00 = 0110-00 = Central Office (only used in chassis) 0x7-00 = 0111-00 = Alteon WebSystems b : Interface / Device type variation: (Were 3 bits, 2 bits taken by family) 0x1 = 1 = M-module (128K RARU records) c : Interface / device type: (5 bits) 0x0 = 00000 = CPU 0x1 = 00001 = Switch fabric 0x2 = 00010 = Copper Ethernet 0x3 = 00011 = Fiber Ethernet 0x4 = 00100 = Sonet (Packets) 0x5 = 00101 = ATM 0x6 = 00110 = Token Ring 0x7 = 00111 = RMON 0x8 = 01000 = BFM (Frame or cells indicated by field 'a' above) 0x9 = 01001 = PSU 0xa = 01010 = Fan Tray 0xb = 01011 = Chassis/Backplane 0xc = 01100 = CPU Mezz 0xd = 01101 = SSL 0xe = 01110 = LaunchPad 0xf = 01111 = reserved for future 0x10 = 10000 = reserved for future 0x11 = 10001 = reserved for future 0x12 = 10010 = reserved for future 0x13 = 10011 = WSM Fiber Ethernet d : Maximum speed (highest negotiable speed) (4 bits) 0x0 = 0000 = 10 Mbit 0x1 = 0001 = 100 Mbit 0x2 = 0010 = 1 Gbit 0x3 = 0011 = 10 Gbit 0x4 = 0100 = OC-3 0x5 = 0101 = OC-12 0x6 = 0110 = OC-48 0x7 = 0111 = OC-92 0x8 = 1000 = OC-192 0x9 = 1001 = 4 Mbit (TR) 0xa = 1010 = 16 Mbit (TR) 0xb = 1011 = E3 0xc = 1100 = DS1 0xd = 1101 = DS3 0xe = 1110 = none (no PHY interfaces on board) 0xf = 1111 = Max speed indicated implicitly in field (c) (for expansion) e : AM&OM-06/28/2006: This bit was originally used to indicate port redundancy. For PR it is used as a differentiator between Boomslang (0) and Copperhead (1). 0=non-redundant, (1 bit) 1=redundant f : Card specific info. (3 bits) For Gigabit used as follows: 000=short-haul (SX) 010=long-haul (LX) 100=extra-distance (DX) 101=GBIC For 10 Gigabit used as follws 000 = 10GE WAN serial 1310nm (XLW) 001 = 10GE WAN serial 1550nm (XEW) 100 = 10GE LAN serial 1310nm (XLR) 101 = 10GE LAN serial 1550nm (XER) 011 = 10GE LAN/WAN (XZW) For ATM/Sonet used as follows 000 = multi mode 001 = single mode 010 = single or multimode 011 = not applicable (e.g., copper has no mode) For Marvin Gardens, indicates number of MDA slots 000 = none 001 = one option slots 010 = two option slots 011 = three option slots For Power Supplies: 000 = AC PSU 001 = DC PSU For CPU Mezz: 000 = MPC755/MPC107 Mezz For SSL: 000 = server offloading 001 = end to end encryption For WSM: 000 = WSM mode 001 = ASFM mode For 8003 (3 slot) chassis differentiation: 000 = ERS 8003 001 = MERS 8003-R (Triumph) 000: PP8300 48TX, 10/100/1000 without POL 001: PP8300 48TX, 10/100/1000 with POL 010: SFP 000: non SFP g : Chassis type (4 bits, possibly MSB 2 bits are extension of field b) 0x0 = 00-00 = work-group (single card switches, etc) 0x1 = 00-01 = back-bone (chassis based products) 0x2 = 00-10 = MDA (option modules) h : Number of ports (binary representation obmited) (8 bits) (for ACIM/BFM cards, this is number of octapids/blackbirds/dea) 0x00 = no ports (cpus, switch fabrics) 0x01 = 1-port, 0x02 = 2-port, 0x04 = 4-port, 0x06 = 6-port, 0x08 = 8-port, 0x0c = 12-port, 0x10 = 16-port, 0x18 = 24-port, 0x22 = 36-port, 0x30 = 48-port, 0x40 = 64-port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), rc2kCPU(537788672), rc2k48x100BaseTX(539033904), rc2k24x100BaseTX(539033880), rc2k32x100BaseTX(539033888), rc2k8x1000BaseT(539099400), rc2k16x1000BaseT(539099408), rc2k24x100BaseFX(540082456), rc2k8x1000BaseSXBB(540147976), rc2k16x1000BaseSXBB(540147984), rc2k8x1000BaseLXBB(540156168), rc2k8x1000BaseXDBB(540164360), rc2k4x1000BaseOPM(540168452), rc2k8x1000BaseIC(540168456), rc2k16x1000BaseIC(540168464), rc2k8x1000BaseSXRBB(540180744), rc2k8x1000BaseLXRBB(540188936), rc2k8xOC3(541327624), rc2k2xOC12(541393154), rc2k6xPOS(541401350), rc2k4xATM(542441732), rc2k8xATM(542441736), rc2kRMON(545128704), rc2k1x10GBaseLW(573767937), rc2k1x10GBaseLR(573784321), rc2k32x100BaseTXM(572588320), rc2k48x100BaseTXM(572588336), rc2k8x1000BaseTM(572653832), rc2k8x1000BaseSXBBM(573702408), rc2k8x1000BaseICM(573722888), rc2k6xPOSM(574955782), rc2k8xATMM(575996168), rc2kPR48X1000BaseTX(606208304), rc2kMg48x100BaseTX(807469360), rc2kMg32x100BaseTX(807473440), rc2kMg16x100BaseFX(808522000), rc2kMg8x1000BaseTX(808583432), rc2kMg8x1000BaseIC(808603912), rc2kMg48x100BaseTC(817955120), rc2kAlteonLP(1893859592), rc2kAlteonWSM(1899102468), rc2kAlteonASFM(1899106564), rc2k61AlteonSAM(1926365441), rc2k62AlteonSAM(1926369537), rc2kPP8300-CPU8x1000BaseSFP(1342316808), rc2kPP8300-24x1000BaseTX(1344405784), rc2kPP8300-48x100BaseTX(1344340272), rc2kPP8300-48x100BaseTXPOE(1344344368), rc2kPR30X1000BaseSXBB(607277342), rc2kPR3X10GBaseGbic(607338755), rc2kPR3X10GBaseXZW(607346947), rc2kPR48x1000BaseGBRS(607277360), rc2kPR48x1000BaseGTRS(606241072), rc2kPR12X10GBaseXLRS(607338764), rc2kPR34xXGRS(607277346), rc2kCPURed(537792768), rc2kPRE48x1000BaseGB(632443184), rc2kPRE48x1000BaseGT(631406896), rc2kPRE12X10GBaseXL(632504588), rc2kPRE34xXG(632443170)

rc2kCardFrontDescription		1.3.6.1.4.1.2272.1.100.6.1.3
description
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..20)

rc2kCardFrontAdminStatus		1.3.6.1.4.1.2272.1.100.6.1.4
Used to indicate the administrative status of this card
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	up(1), down(2), testing(3), reset(4)

rc2kCardFrontOperStatus		1.3.6.1.4.1.2272.1.100.6.1.5
Used to indicate the operational status of this card.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2), testing(3), unknown(4), dormant(5)

rc2kCardFrontSerialNum		1.3.6.1.4.1.2272.1.100.6.1.6
serial number of card
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..20)

rc2kCardFrontHwVersion		1.3.6.1.4.1.2272.1.100.6.1.7
hardware version
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..20)

rc2kCardFrontPartNumber		1.3.6.1.4.1.2272.1.100.6.1.8
part number
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..20)

rc2kCardFrontDateCode		1.3.6.1.4.1.2272.1.100.6.1.9
date code
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..20)

rc2kCardFrontDeviations		1.3.6.1.4.1.2272.1.100.6.1.10
deviations
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..20)

rc2kCardFrontMacAddr		1.3.6.1.4.1.2272.1.100.6.1.11
base mac address
Status: obsolete	Access: read-only
OBJECT-TYPE
	MacAddress

rc2kCardBackType		1.3.6.1.4.1.2272.1.100.6.1.12
Refer to rc2kCardFrontType for the encoding scheme
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), rc2kBackplane(536969472), rc2kSFM(538837248), rc2kBFM0(546177280), rc2kBFM2(546177282), rc2kBFM3(546177283), rc2kBFM4(1888354564), rc2kBFM6(546177286), rc2kBFM8(546177288), rc2kMGSFM(807272704), rc2kFSFM(605946112), rc2kDPM1(613351861), rc2kDPM2(613351682), rc2kDPM3(613351863), rc2kEDPM2(613351690), rc2kEDPM3(613351871), rc2kEEDPM2(630128906), rc2kEEDPM3(630129087)

rc2kCardBackDescription		1.3.6.1.4.1.2272.1.100.6.1.13
description
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..20)

rc2kCardBackSerialNum		1.3.6.1.4.1.2272.1.100.6.1.14
serial number of card
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..20)

rc2kCardBackHwVersion		1.3.6.1.4.1.2272.1.100.6.1.15
hardware version
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..20)

rc2kCardBackPartNumber		1.3.6.1.4.1.2272.1.100.6.1.16
part number
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..20)

rc2kCardBackDateCode		1.3.6.1.4.1.2272.1.100.6.1.17
date code
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..20)

rc2kCardBackDeviations		1.3.6.1.4.1.2272.1.100.6.1.18
deviations
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..20)

rc2kCardPCMCIAType		1.3.6.1.4.1.2272.1.100.6.1.19
Used to indicate the type of PCMCIA card currently installed in this CPU card, if any. For non-CPU cards, this variable has no meaning and will always be set to none(1).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), modemCard(2), ethernetCard(3), ataDisk(4)

rc2kCardPCMCIADescr		1.3.6.1.4.1.2272.1.100.6.1.20
PCMCIA descriptor
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..128)

rc2kCardASICDescr		1.3.6.1.4.1.2272.1.100.6.1.21
ASIC descriptor
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..128)

rc2kCardFrontMasterIO		1.3.6.1.4.1.2272.1.100.6.1.22
Used to indicate whether an IO card in a 8100 device is operating in the 'master' mode. This variable is not meaningful for non-IO cards and non-8100 devices.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rc2kCardSmltOnSingleCpSupported		1.3.6.1.4.1.2272.1.100.6.1.23
Used to indicate whether an IO card is updated to support SMLT on single Cp feature or not.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rc2kCardMezzCard		1.3.6.1.4.1.2272.1.100.6.1.24
Used to indicate the CPU Mezz card
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unsupported(1), notpresent(2), present(3), running(4)

rc2kCardMezzSerialNum		1.3.6.1.4.1.2272.1.100.6.1.26
Used to get the serial number of the mezz
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

rc2kCardMezzHwVersion		1.3.6.1.4.1.2272.1.100.6.1.27
Used to get the HW version of the mezz. The value of HW Version corresponds to the value of part number.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	undefined(0), e0(1), e1(2), e2(3), e3(4), e4(5), e5(6), e6(7), e7(8)

rc2kCardMezzPartNum		1.3.6.1.4.1.2272.1.100.6.1.28
Used to get the part number of the mezz. The value of part number corresponds to the value of HW Version.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	undefined(0), p120616(1), p120618(2), p120617(3), p120615(4), p120724(5), p120672(6), p120851(7), p120939(8)

rc2kCardSlotPriority		1.3.6.1.4.1.2272.1.100.6.1.29
Used to indicate the priority of the slot for power management. It will take effect only after reboot.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	critical(1), high(2), low(3)

rc2kCardSlotOriginalPriority		1.3.6.1.4.1.2272.1.100.6.1.30
Priority of the slot for power management which the swtich has currently booted with. It will remain the same until the next reboot.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	critical(1), high(2), low(3)

rc2kCardModuleSerialNum		1.3.6.1.4.1.2272.1.100.6.1.33
Module serial number. It is only applicable to the RS module. And it is not applicable to old version of the R module and CP
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..20)

rc2kCardModulePartNumber		1.3.6.1.4.1.2272.1.100.6.1.34
Module part number. It is only applicable to the RS module. And it is not applicable to old version of the R module and CP
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..20)

rc2kCardModuleAssemblyDate		1.3.6.1.4.1.2272.1.100.6.1.35
Module assemly date. It is only applicable to the RS module. And it is not applicable to old version of the R module and CP
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..20)

rc2kCopyFile		1.3.6.1.4.1.2272.1.100.7
OBJECT IDENTIFIER

rc2kCopyFileSource		1.3.6.1.4.1.2272.1.100.7.1
source file
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..256)

rc2kCopyFileDestination		1.3.6.1.4.1.2272.1.100.7.2
dest file
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..256)

rc2kCopyFileAction		1.3.6.1.4.1.2272.1.100.7.3
start or cancell
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), start(2)

rc2kCopyFileResult		1.3.6.1.4.1.2272.1.100.7.4
result
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), inProgress(2), success(3), fail(4), invalidSource(5), invalidDestination(6), outOfMemory(7), outOfSpace(8), fileNotFound(9)

rc2kQos		1.3.6.1.4.1.2272.1.100.8
OBJECT IDENTIFIER

rc2kQosQosTable		1.3.6.1.4.1.2272.1.100.8.1
This table is used to define the Quality Of Service(QOS) profiles for the system. The system can support eight different QOS levels. Each QOS level can be individually configured.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Rc2kQosQosEntry

rc2kQosQosEntry		1.3.6.1.4.1.2272.1.100.8.1.1
QOS profile entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	Rc2kQosQosEntry

rc2kQosQosRow		1.3.6.1.4.1.2272.1.100.8.1.1.1
Used to uniquely identify a row in this table.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..8

rc2kQosQosLevel		1.3.6.1.4.1.2272.1.100.8.1.1.2
QOS level
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..7

rc2kQosQosName		1.3.6.1.4.1.2272.1.100.8.1.1.3
Qos level name
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

rc2kQosQosAdminWeight		1.3.6.1.4.1.2272.1.100.8.1.1.4
Administrative transmit opportunity percentage
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rc2kQosQosOperWeight		1.3.6.1.4.1.2272.1.100.8.1.1.5
Operational transmit opportunity percentage
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rc2kQosOctapidMode		1.3.6.1.4.1.2272.1.100.8.1.1.6
Octapid mode
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	modeSingle(1), mode100(2)

rc2kQosQosAdminThreshold		1.3.6.1.4.1.2272.1.100.8.1.1.7
Administrative queue threshold
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), oneEight(1), oneQuarter(2), threeEight(3), halfSdram(4), fiveEight(5), threeQuarter(6), sevenEights(7), allSdram(8), notpresent(9)

rc2kQosQosOperThreshold		1.3.6.1.4.1.2272.1.100.8.1.1.8
Operational queue threshold
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(0), oneEight(1), oneQuarter(2), threeEight(3), halfSdram(4), fiveEight(5), threeQuarter(6), sevenEights(7), allSdram(8), notpresent(9)

rc2kQosPidMode		1.3.6.1.4.1.2272.1.100.8.1.1.9
Pid mode
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	modeSingle(1), mode100(2)

rc2kQosIngressTagToQosTable		1.3.6.1.4.1.2272.1.100.8.2
This table is used to specify the 802.1P to QOS (802.1P->QOS) mapping on packet ingress.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Rc2kQosIngressTagToQosEntry

rc2kQosIngressTagToQosEntry		1.3.6.1.4.1.2272.1.100.8.2.1
Entry containing infomation of 8021P->Qos mapping
Status: current	Access: not-accessible
OBJECT-TYPE
	Rc2kQosIngressTagToQosEntry

rc2kQosIngressTagToQosRow		1.3.6.1.4.1.2272.1.100.8.2.1.1
Used to uniquely identify a row in this table.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..8

rc2kQosIngressTagToQosInIeee8021P		1.3.6.1.4.1.2272.1.100.8.2.1.2
802.1P
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..7

rc2kQosIngressTagToQosQosLevel		1.3.6.1.4.1.2272.1.100.8.2.1.3
Qos level
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..7

rc2kQosIngressDsFieldToQosTable		1.3.6.1.4.1.2272.1.100.8.3
This table is used to specify the DSCP field to QOS (DsField->QOS) mapping on packet ingress.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Rc2kQosIngressDsFieldToQosEntry

rc2kQosIngressDsFieldToQosEntry		1.3.6.1.4.1.2272.1.100.8.3.1
Entry containing infomation of DsField->Qos mapping
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	Rc2kQosIngressDsFieldToQosEntry

rc2kQosIngressDsFieldToQosRow		1.3.6.1.4.1.2272.1.100.8.3.1.1
Used to uniquely identify a row in this table.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	1..64

rc2kQosIngressDsFieldToQosInDsField		1.3.6.1.4.1.2272.1.100.8.3.1.2
diffserv dsField
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	0..63

rc2kQosIngressDsFieldToQosQosLevel		1.3.6.1.4.1.2272.1.100.8.3.1.3
qos level
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	0..7

rc2kQosEgressQosToTagTable		1.3.6.1.4.1.2272.1.100.8.4
This table is used to specify the QOS to 802.1P (QOS->802.1P) mapping on packet egress.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Rc2kQosEgressQosToTagEntry

rc2kQosEgressQosToTagEntry		1.3.6.1.4.1.2272.1.100.8.4.1
Entry containing infomation of Qos->Qos mapping
Status: current	Access: not-accessible
OBJECT-TYPE
	Rc2kQosEgressQosToTagEntry

rc2kQosEgressQosToTagRow		1.3.6.1.4.1.2272.1.100.8.4.1.1
Used to uniquely identify a row in this table.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..8

rc2kQosEgressQosToTagQosLevel		1.3.6.1.4.1.2272.1.100.8.4.1.2
qos level
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..7

rc2kQosEgressQosToTagOutIeee8021P		1.3.6.1.4.1.2272.1.100.8.4.1.3
802.1P
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..7

rc2kQosEgressQosToDsFieldTable		1.3.6.1.4.1.2272.1.100.8.5
This table is used to specify the QOS to DSCP field (QOS->DsField) mapping on packet egress.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Rc2kQosEgressQosToDsFieldEntry

rc2kQosEgressQosToDsFieldEntry		1.3.6.1.4.1.2272.1.100.8.5.1
Entry containing infomation of Qos->Qos mapping
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	Rc2kQosEgressQosToDsFieldEntry

rc2kQosEgressQosToDsFieldRow		1.3.6.1.4.1.2272.1.100.8.5.1.1
Used to uniquely identify a row in this table.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	1..8

rc2kQosEgressQosToDsFieldQosLevel		1.3.6.1.4.1.2272.1.100.8.5.1.2
qos level
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	0..7

rc2kQosEgressQosToDsFieldOutDsField		1.3.6.1.4.1.2272.1.100.8.5.1.3
diffserv dsField
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	0..63

rc2kQosTrafficProfileTable		1.3.6.1.4.1.2272.1.100.8.6
This table is used to specify traffic profiles for the system. These traffic profiles are used for policying purposes to guarantee streams of traffic do not egress the system above a certain rate. These traffic profiles are applied in the 'rcIpFilterTable'.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Rc2kQosTrafficProfileEntry

rc2kQosTrafficProfileEntry		1.3.6.1.4.1.2272.1.100.8.6.1
Entry containing infomation of Qos->Qos mapping
Status: current	Access: not-accessible
OBJECT-TYPE
	Rc2kQosTrafficProfileEntry

rc2kQosTrafficProfileId		1.3.6.1.4.1.2272.1.100.8.6.1.1
Profile id
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..64

rc2kQosTrafficProfileName		1.3.6.1.4.1.2272.1.100.8.6.1.2
Profile name
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..32)

rc2kQosTrafficProfileEnable		1.3.6.1.4.1.2272.1.100.8.6.1.3
Enable this entry
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rc2kQosTrafficProfileTranslateDscpEnable		1.3.6.1.4.1.2272.1.100.8.6.1.4
Used to specify whether translation of the DSCP field should be performed. If enabled, the value in the DSCP field for packets that fall within the traffic profile will get translated to 'rc2kQosTrafficProfileInProfileDscp'. Packets that fall outside the traffic profile will get translated to 'rc2kQosTrafficProfileOutProfileDscp'. If disabled, no translation is performed.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rc2kQosTrafficProfileInProfileDscp		1.3.6.1.4.1.2272.1.100.8.6.1.5
Used to specify the DSCP value for 'good' packets.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(6)

rc2kQosTrafficProfileOutProfileDscp		1.3.6.1.4.1.2272.1.100.8.6.1.6
Used to specify the DSCP value for 'violation' packets.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(6)

rc2kQosTrafficProfileDiscardEnable		1.3.6.1.4.1.2272.1.100.8.6.1.7
Used to specify whether packets that fall outside the traffic profile should be discarded.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rc2kQosTrafficProfileAverageRate		1.3.6.1.4.1.2272.1.100.8.6.1.8
Average rate in packets per second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rc2kQosTrafficProfilePeakRate		1.3.6.1.4.1.2272.1.100.8.6.1.9
Peak rate in packets per second.
Status: deprecated	Access: read-write
OBJECT-TYPE
	Integer32

rc2kQosTrafficProfileRowStatus		1.3.6.1.4.1.2272.1.100.8.6.1.10
Used to create/delete entries.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rc2kQosIngressDscpToQosTable		1.3.6.1.4.1.2272.1.100.8.7
This table is used to specify the DSCP to QOS (Dscp->QOS) mapping on packet ingress.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Rc2kQosIngressDscpToQosEntry

rc2kQosIngressDscpToQosEntry		1.3.6.1.4.1.2272.1.100.8.7.1
Entry containing information of Dscp->Qos mapping
Status: current	Access: not-accessible
OBJECT-TYPE
	Rc2kQosIngressDscpToQosEntry

rc2kQosIngressDscpToQosRow		1.3.6.1.4.1.2272.1.100.8.7.1.1
Used to uniquely identify a row in this table.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..64

rc2kQosIngressDscpToQosInDscp		1.3.6.1.4.1.2272.1.100.8.7.1.2
A 6-bit value used to define the Differentiated Service Code Point(DSCP).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..63

rc2kQosIngressDscpToQosInDscpBinaryFormat		1.3.6.1.4.1.2272.1.100.8.7.1.3
The 'rc2kQosIngressDscpToQosInDscp' value shown in a binary format (network order).
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(6)

rc2kQosIngressDscpToQosQosLevel		1.3.6.1.4.1.2272.1.100.8.7.1.4
qos level
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..7

rc2kQosEgressQosToDscpTable		1.3.6.1.4.1.2272.1.100.8.8
This table is used to specify the QOS to DSCP field (QOS->DsField) mapping on packet egress.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Rc2kQosEgressQosToDscpEntry

rc2kQosEgressQosToDscpEntry		1.3.6.1.4.1.2272.1.100.8.8.1
Entry containing infomation of Qos->Qos mapping
Status: current	Access: not-accessible
OBJECT-TYPE
	Rc2kQosEgressQosToDscpEntry

rc2kQosEgressQosToDscpRow		1.3.6.1.4.1.2272.1.100.8.8.1.1
Used to uniquely identify a row in this table.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..8

rc2kQosEgressQosToDscpQosLevel		1.3.6.1.4.1.2272.1.100.8.8.1.2
qos level
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..7

rc2kQosEgressQosToDscpOutDscp		1.3.6.1.4.1.2272.1.100.8.8.1.3
A 6-bit value used to define the Differentiated Service Code Point(DSCP).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..63

rc2kQosEgressQosToDscpOutDscpBinaryFormat		1.3.6.1.4.1.2272.1.100.8.8.1.4
The 'rc2kQosEgressQosToDscpOutDscp' value show in a binary format (network order).
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(6)

rc2kAtm		1.3.6.1.4.1.2272.1.100.9
OBJECT IDENTIFIER

rc2kAtmGlobal		1.3.6.1.4.1.2272.1.100.9.1
OBJECT IDENTIFIER

rc2kAtmPortTable		1.3.6.1.4.1.2272.1.100.9.2
ATM port table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Rc2kAtmPortEntry

rc2kAtmPortEntry		1.3.6.1.4.1.2272.1.100.9.2.1
Entry containing infomation of ATM port
Status: current	Access: not-accessible
OBJECT-TYPE
	Rc2kAtmPortEntry

rc2kAtmPortIfIndex		1.3.6.1.4.1.2272.1.100.9.2.1.1
port number
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rc2kAtmPortNumVpiBits		1.3.6.1.4.1.2272.1.100.9.2.1.2
# of vpi bits. For OC3, the max number of vpibits is 6. However, for OC12, it is 8. Both media types share the same MIB object.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..8

rc2kAtmPortNumVciBits		1.3.6.1.4.1.2272.1.100.9.2.1.3
# of vci bits
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..16

rc2kAtmPortMediaType		1.3.6.1.4.1.2272.1.100.9.2.1.4
media type
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	smf(1), mmf(2), ds3(3)

rc2kAtmPortScrambleEnable		1.3.6.1.4.1.2272.1.100.9.2.1.5
enable scramble
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rc2kAtmPortFramingMode		1.3.6.1.4.1.2272.1.100.9.2.1.6
port framing mode
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	sonet(1), sdh(2), ds3CbitAdm(3), ds3CbitPlcp(4), ds3M23Adm(5), ds3M23Plcp(6)

rc2kAtmPortClockSource		1.3.6.1.4.1.2272.1.100.9.2.1.7
clock source
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	loopTimed(1), freeRunning(2)

rc2kAtmPortLineSpeed		1.3.6.1.4.1.2272.1.100.9.2.1.8
line speed
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	oc3c(1), oc12c(2), ds3(3)

rc2kAtmPortLoopBackMode		1.3.6.1.4.1.2272.1.100.9.2.1.9
loop back mode
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(1), internal(2), external(3), ds3PayloadLoop(4), ds3DiagLoop(5), ds3LineLoop(6)

rc2kAtmPortMacAddress		1.3.6.1.4.1.2272.1.100.9.2.1.10
XLR assigned MAC addr
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rc2kAtmPvcTable		1.3.6.1.4.1.2272.1.100.9.3
ATM Pvc table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Rc2kAtmPvcEntry

rc2kAtmPvcEntry		1.3.6.1.4.1.2272.1.100.9.3.1
Entry containing infomation of ATM Pvc
Status: current	Access: not-accessible
OBJECT-TYPE
	Rc2kAtmPvcEntry

rc2kAtmPvcIfIndex		1.3.6.1.4.1.2272.1.100.9.3.1.1
port number
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rc2kAtmPvcVpi		1.3.6.1.4.1.2272.1.100.9.3.1.2
vpi of this pvc
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..255

rc2kAtmPvcVci		1.3.6.1.4.1.2272.1.100.9.3.1.3
vci of this pvc
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..4095

rc2kAtmPvcPvcId		1.3.6.1.4.1.2272.1.100.9.3.1.4
internal pvc id
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rc2kAtmPvcName		1.3.6.1.4.1.2272.1.100.9.3.1.5
name of pvc
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rc2kAtmPvcEncapsulation		1.3.6.1.4.1.2272.1.100.9.3.1.6
encapsulation
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	null(1), llcSnap(2)

rc2kAtmPvcServiceType		1.3.6.1.4.1.2272.1.100.9.3.1.7
service type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ubr(1), vbr(2)

rc2kAtmPvcPeakCellRate		1.3.6.1.4.1.2272.1.100.9.3.1.8
Peak cell rate in cells per second. The maximum peak cell rate is half of the line rate. The peak cell rate for MDA type OC12 must be less than 733491. However, for OC3, it is less than 182783.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	86..733490

rc2kAtmPvcSustainedCellRate		1.3.6.1.4.1.2272.1.100.9.3.1.9
Sustained cell rate in cells per second. The maximum peak cell rate is half of the line rate. The peak cell rate for MDA type OC12 must be less than 733491. However, for OC3, it is less than 182783.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	86..733490

rc2kAtmPvcMaxBurstSize		1.3.6.1.4.1.2272.1.100.9.3.1.10
max burst size
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	2..255

rc2kAtmPvcRowStatus		1.3.6.1.4.1.2272.1.100.9.3.1.11
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rc2kAtmPvcOamLbMgmtEnable		1.3.6.1.4.1.2272.1.100.9.3.1.12
Indicate whether end-to-end F5 OAM loopback is enabled. When it is enabled, OAM loopback request is sent periodically
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rc2kAtmPvcOamLbSendFrequency		1.3.6.1.4.1.2272.1.100.9.3.1.13
Number of seconds between transmitting OAM loopback request
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..255

rc2kAtmPvcOamLbRetryFrequency		1.3.6.1.4.1.2272.1.100.9.3.1.14
Number of seconds between retry
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..255

rc2kAtmPvcOamLbUpCount		1.3.6.1.4.1.2272.1.100.9.3.1.15
Number of consecutive end-to-end F5 OAM loopback cell responses that must be received in order to change a PVC connection state to up
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..255

rc2kAtmPvcOamLbDownCount		1.3.6.1.4.1.2272.1.100.9.3.1.16
Number of consecutive end-to-end F5 OAM loopback cell responses that are not received in order to change a PVC state to down.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..255

rc2kAtmPvcOamTrapEnable		1.3.6.1.4.1.2272.1.100.9.3.1.17
Indicate whether OAM trap is enabled. When it is enabled, a trap is sent to the management station when rc2kAtmPvcOamVcStatus is going up or down.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rc2kAtmPvcOamVcStatus		1.3.6.1.4.1.2272.1.100.9.3.1.18
Indicate the status of PVC link. Not Managed--VC is not being managed by OAM. Down Verify --An OAM loopback failed. End-to-end F5 OAM loopback cells are sent at retry frequency to verify the VC is really down. After down-count unsuccessful retries, the VC goes to the down state (see definition of rc2kAtmPvcOamLoopbackDownCount). Down --VC has not received responses to by end-to-end F5 OAM loopback cells. Up Verify -- An OAM loopback was successful. End-to-end F5 OAM loopback cells are sent at retry frequency to verify the VC is really up. After up-count successive and successful loopback retries, the VC goes to the Up state (see definition of rc2kAtmPvcOamLoopbackUpCount). Up - End-to-end loopbacks are successful.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notManaged(1), downVerify(2), down(3), upVerify(4), up(5)

rc2kAtmPvcOamLbRequestSent		1.3.6.1.4.1.2272.1.100.9.3.1.19
Number of OAM loopback request sent
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rc2kAtmPvcOamLbReplySent		1.3.6.1.4.1.2272.1.100.9.3.1.20
Number of OAM loopback reply sent
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rc2kAtmPvcOamLbReplyReceived		1.3.6.1.4.1.2272.1.100.9.3.1.21
Number of OAM loopback reply received
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rc2kAtm1483ElanTable		1.3.6.1.4.1.2272.1.100.9.5
ATM 1483Elan table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Rc2kAtm1483ElanEntry

rc2kAtm1483ElanEntry		1.3.6.1.4.1.2272.1.100.9.5.1
Entry containing infomation of ATM 1483Elan
Status: current	Access: not-accessible
OBJECT-TYPE
	Rc2kAtm1483ElanEntry

rc2kAtm1483ElanIfIndex		1.3.6.1.4.1.2272.1.100.9.5.1.1
port number
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rc2kAtm1483ElanElanId		1.3.6.1.4.1.2272.1.100.9.5.1.2
Elan Id
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rc2kAtm1483ElanNumPvcIds		1.3.6.1.4.1.2272.1.100.9.5.1.3
# pvc-ids in list
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..64

rc2kAtm1483ElanPvcIds		1.3.6.1.4.1.2272.1.100.9.5.1.4
list of pvc-ids. each pvc-id is represented by a 32 bit value this field can contain a maximum of 64 pvc-ids.
Status: current	Access: read-write
OBJECT-TYPE
	IdList	Size(256)

rc2kAtm1483ElanVlanId		1.3.6.1.4.1.2272.1.100.9.5.1.5
vlan tag for this 1483
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..2147483647

rc2kAtm1483ElanRowStatus		1.3.6.1.4.1.2272.1.100.9.5.1.6
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rc2kAtm1483ElanConnectType		1.3.6.1.4.1.2272.1.100.9.5.1.7
connection type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	bridged(1), ip(2), ipx(3), muxIpIpx(4)

rc2kAtm1483ElanVlanMacAddress		1.3.6.1.4.1.2272.1.100.9.5.1.8
mac for vlan
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rc2kAtm1483ElanDummyMacAddress		1.3.6.1.4.1.2272.1.100.9.5.1.9
dummy mac for the other router
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rc2kAtm1483ElanLocalIpAddress		1.3.6.1.4.1.2272.1.100.9.5.1.10
local ip, if ConnectType is ip(2)
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rc2kAtm1483ElanRemoteIpAddress		1.3.6.1.4.1.2272.1.100.9.5.1.11
remote ip, if ConnectType is ip(2)
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rc2kAtm1483ElanInArpSendEnable		1.3.6.1.4.1.2272.1.100.9.5.1.12
enable arp sending on the port, if ConnectType is ip(2)
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rc2kAtm1483ElanInArpSendInterval		1.3.6.1.4.1.2272.1.100.9.5.1.13
interval of arp sending on the port, if ConnectType is ip(2)
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..60

rc2kAtm1483ElanIpxVlanEncapMethod		1.3.6.1.4.1.2272.1.100.9.5.1.14
vlan encapsulation method, if ConnectType is ipx(3)
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	llc(1), snap(2), ether-ii(3), raw(4)

rc2kAtm1483ElanIpxNetworkNum		1.3.6.1.4.1.2272.1.100.9.5.1.15
network number, if ConnectType is ipx(3)
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..2147483647

rc2kAtm1483ElanStgId		1.3.6.1.4.1.2272.1.100.9.5.1.16
An identifier used to identify a STG in the device, only in bridge mode
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rc2kAtm1483ElanrcStgTaggedBpduVlanId		1.3.6.1.4.1.2272.1.100.9.5.1.17
The VLAN ID to be used for tagging BPDUs, only in bridge mode.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rc2kAtm1483ElanIpxNetworkAddr		1.3.6.1.4.1.2272.1.100.9.5.1.18
network number, instead of rc2kAtm1483ElanIpxNetworkNum
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(4)

rc2kAtmSioCardConfigTable		1.3.6.1.4.1.2272.1.100.9.8
2kAtm Sio Card Config Table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Rc2kAtmSioCardConfigEntry

rc2kAtmSioCardConfigEntry		1.3.6.1.4.1.2272.1.100.9.8.1
Entry containing infomation of 2kAtm Sio Card Config.
Status: current	Access: not-accessible
OBJECT-TYPE
	Rc2kAtmSioCardConfigEntry

rc2kAtmSioCardConfigSlotIndex		1.3.6.1.4.1.2272.1.100.9.8.1.1
slot Index.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

rc2kAtmSioCardConfigAction		1.3.6.1.4.1.2272.1.100.9.8.1.2
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(0), reset(1)

rc2kAtmSioCardConfigTraceMode		1.3.6.1.4.1.2272.1.100.9.8.1.3
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(0), traceOn(1)

rc2kAtmSioCardConfigImageFileName		1.3.6.1.4.1.2272.1.100.9.8.1.4
ATM Image file name.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

rc2kAtmSioCardConfigElanStatsEnable		1.3.6.1.4.1.2272.1.100.9.8.1.5
Enable/Disable Elan Statistics collection
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

rc2kAtmSioCardConfigStatsPollPeriod		1.3.6.1.4.1.2272.1.100.9.8.1.6
Time interval after which Elan statistics would be polled
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	3..15

rc2kAtmElanStatsClearAll		1.3.6.1.4.1.2272.1.100.9.1.1
Clear all Elan Statistics
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rc2kAtmPortStatsTable		1.3.6.1.4.1.2272.1.100.9.10
ATM port statistics table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Rc2kAtmPortStatsEntry

rc2kAtmPortStatsEntry		1.3.6.1.4.1.2272.1.100.9.10.1
Entry containing infomation of ATM port statistics
Status: current	Access: not-accessible
OBJECT-TYPE
	Rc2kAtmPortStatsEntry

rc2kAtmPortStatsIfIndex		1.3.6.1.4.1.2272.1.100.9.10.1.1
port number
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rc2kAtmPortStatsInCells		1.3.6.1.4.1.2272.1.100.9.10.1.2
Number of Cells received from ATM interface
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rc2kAtmPortStatsOutCells		1.3.6.1.4.1.2272.1.100.9.10.1.3
Number of Cells transmitted by ATM interface
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rc2kAtmPortStatsOutIdleCells		1.3.6.1.4.1.2272.1.100.9.10.1.4
Number of Idle Cells transmitted
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rc2kAtmPortStatsInHecCorrected		1.3.6.1.4.1.2272.1.100.9.10.1.5
Number of received cells in which HCS was corrected
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rc2kAtmPortStatsInHecUncorrected		1.3.6.1.4.1.2272.1.100.9.10.1.6
Number of received cells dropped because HCS couldn't be corrected
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rc2kAtmPortStatsInUnknownProtos		1.3.6.1.4.1.2272.1.100.9.10.1.7
Number of received cells dropped with wrong VPI/VCI
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rc2kAtmPortStatsInPkts		1.3.6.1.4.1.2272.1.100.9.10.1.8
Number of AAL5 CPCS PDUs received
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rc2kAtmPortStatsOutPkts		1.3.6.1.4.1.2272.1.100.9.10.1.9
Number of AAL5 CPCS PDUs transmitted
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rc2kAtmPortStatsInDroppedPkts		1.3.6.1.4.1.2272.1.100.9.10.1.10
Number of AAL5 CPCS PDUs dropped due to resource exhaustion
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rc2kAtmPortStatsOutDroppedPkts		1.3.6.1.4.1.2272.1.100.9.10.1.11
Number of AAL5 CPCS PDUs dropped because the transmitter closed the channel
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rc2kAtmVPortStatsTable		1.3.6.1.4.1.2272.1.100.9.11
ATM Elan statistics table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Rc2kAtmVPortStatsEntry

rc2kAtmVPortStatsEntry		1.3.6.1.4.1.2272.1.100.9.11.1
Entry containing infomation of ATM Elan statistics
Status: current	Access: not-accessible
OBJECT-TYPE
	Rc2kAtmVPortStatsEntry

rc2kAtmVPortStatsIfIndex		1.3.6.1.4.1.2272.1.100.9.11.1.1
port number
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rc2kAtmVPortStatsVlanId		1.3.6.1.4.1.2272.1.100.9.11.1.2
Vlan Id
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

rc2kAtmVPortStatsClear		1.3.6.1.4.1.2272.1.100.9.11.1.3
Clear Elan Stats
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(0), clear(1)

rc2kAtmVPortStatsInOctets		1.3.6.1.4.1.2272.1.100.9.11.1.4
AAL5 CPCS PDU octects received from ATM interface
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rc2kAtmVPortStatsOutOctets		1.3.6.1.4.1.2272.1.100.9.11.1.5
AAL5 CPCS PDU octects transmitted out of ATM interface
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rc2kAtmVPortStatsInErrors		1.3.6.1.4.1.2272.1.100.9.11.1.6
AAL5 CPCS PDUs received with errors from ATM interface. These errors include CRC-32 errors,SAR time-out errors And oversized SDU errors
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rc2kAtmVPortStatsOutErrors		1.3.6.1.4.1.2272.1.100.9.11.1.7
Number of AAL5 CPCS PDUs that couldn't be transmitted due to errors
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rc2kAtmVPortStatsInDiscards		1.3.6.1.4.1.2272.1.100.9.11.1.8
Number of received AAL5 CPCS PDUs discarded
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rc2kAtmVPortStatsOutDiscards		1.3.6.1.4.1.2272.1.100.9.11.1.9
Number of AAL5 CPCS PDUs which are to be transmitted but discarded
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rc2kAtmVPortStatsInUcastPkts		1.3.6.1.4.1.2272.1.100.9.11.1.10
Received ethernet/IP/IPX packets whose destination address is neither a multicast nor a broadcast address
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rc2kAtmVPortStatsOutUcastPkts		1.3.6.1.4.1.2272.1.100.9.11.1.11
Forwarded ethernet/IP/IPX packets whose destination address is neither a multicast nor a broadcast address
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rc2kAtmVPortStatsInMulticastPkts		1.3.6.1.4.1.2272.1.100.9.11.1.12
Received ethernet/IP/IPX packets whose destination MAC address(or IP address in case of IP ELAN type) is multicast MAC address or class D IP address (in case of IP ELAN type)
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rc2kAtmVPortStatsOutMulticastPkts		1.3.6.1.4.1.2272.1.100.9.11.1.13
Forwarded ethernet/IP/IPX packets whose destination MAC address(or IP address in case of IP ELAN type) is multicast MAC address or class D IP address (in case of IP ELAN type)
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rc2kAtmVPortStatsInBroadcastPkts		1.3.6.1.4.1.2272.1.100.9.11.1.14
Received ethernet/IP/IPX packets whose destination address in broadcast address
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rc2kAtmVPortStatsOutBroadcastPkts		1.3.6.1.4.1.2272.1.100.9.11.1.15
Forwarded ethernet/IP/IPX packets whose destination address in broadcast address
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rc2kMdaCardTable		1.3.6.1.4.1.2272.1.100.10
Mda card table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Rc2kMdaCardEntry

rc2kMdaCardEntry		1.3.6.1.4.1.2272.1.100.10.1
Entry containing infomation of Mda card
Status: current	Access: not-accessible
OBJECT-TYPE
	Rc2kMdaCardEntry

rc2kMdaCardSlotNum		1.3.6.1.4.1.2272.1.100.10.1.1
Slot number
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..10

rc2kMdaCardMdaNum		1.3.6.1.4.1.2272.1.100.10.1.2
MDA number within slot. MDAs are numbered from left to right.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4

rc2kMdaCardType		1.3.6.1.4.1.2272.1.100.10.1.3
Refer to rc2kCardFrontType for the encoding scheme
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), rc2k4x100BaseTX(807469572), rc2k2x100BaseFX(808518146), rc2k4x100BaseFX(808518148), rc2k1x1000BaseSXBB(808583681), rc2k1x1000BaseSXRBB(808616449), rc2k1x1000BaseLXBB(808591873), rc2k1x1000BaseLXRBB(808624641), rc2k4xOc3cBaseSM(542380548), rc2k4xOc3cBaseMM(542376452), rc2k4xOc3cBaseCOPPER(542388740), rc2k1x0c12cBaseSM(542446081), rc2k1x0c12cBaseMM(542441985), rc2k2xDs3(542970370), rc2k2xE3(542839298), rc2k2xOc3PosBaseMMF(541327874), rc2k2xOc3PosBaseSMF(541331970), rc2k1xOc12PosBaseMMF(541393409), rc2k1xOc12PosBaseSMF(541397505)

rc2kMdaCardDescription		1.3.6.1.4.1.2272.1.100.10.1.4
description of mda card
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

rc2kMdaCardAdminStatus		1.3.6.1.4.1.2272.1.100.10.1.5
administration status of mda card
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	up(0), down(1), testing(2), unknown(3)

rc2kMdaCardOperStatus		1.3.6.1.4.1.2272.1.100.10.1.6
operation status of mda card.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(0), down(1), testing(2), unknown(3)

rc2kMdaCardSerialNum		1.3.6.1.4.1.2272.1.100.10.1.7
serial number of mad card
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

rc2kMdaCardHwVersion		1.3.6.1.4.1.2272.1.100.10.1.8
hardware version of mda card
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

rc2kMdaCardPartNumber		1.3.6.1.4.1.2272.1.100.10.1.9
part number of mda card
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

rc2kMdaCardDateCode		1.3.6.1.4.1.2272.1.100.10.1.10
date code of mda card
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

rc2kMdaCardDeviations		1.3.6.1.4.1.2272.1.100.10.1.11
hardware deviation infomation of mda card
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

rc2kMdaCardMacAddr		1.3.6.1.4.1.2272.1.100.10.1.12
base mac address of mda card
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rc2kMdaCardNumPorts		1.3.6.1.4.1.2272.1.100.10.1.13
number of ports on mda card
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rc2kMdaCardFirstIfIndex		1.3.6.1.4.1.2272.1.100.10.1.14
first ifindex number on mda card
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rc2kMdaCardLastIfIndex		1.3.6.1.4.1.2272.1.100.10.1.15
last ifindex number on mda card
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rc2kCpuEthernetPortRouteTable		1.3.6.1.4.1.2272.1.100.11
2k CPU Ethernet Port Route table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Rc2kCpuEthernetPortRouteEntry

rc2kCpuEthernetPortRouteEntry		1.3.6.1.4.1.2272.1.100.11.1
Entry containing infomation of 2k CPU Ethernet Port
Status: current	Access: not-accessible
OBJECT-TYPE
	Rc2kCpuEthernetPortRouteEntry

rc2kCpuEthernetPortRouteNetwork		1.3.6.1.4.1.2272.1.100.11.1.1
Used to configure the network that can be used to remotely manage this device.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rc2kCpuEthernetPortRouteGateway		1.3.6.1.4.1.2272.1.100.11.1.2
Used to configure the the IP address of the gateway that should be used to forward IP traffic.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rc2kCpuEthernetPortRouteRowStatus		1.3.6.1.4.1.2272.1.100.11.1.3
row status
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rc2kCPUTypeGeneralGroup		1.3.6.1.4.1.2272.1.100.12
OBJECT IDENTIFIER

rc2kCPUTypePrimary		1.3.6.1.4.1.2272.1.100.12.1
Used to identify the type of primary CPU
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	cpu8690Default(1), cpu8690Upgrade(2), cpu8691Default(3), cpu8691Upgrade(4), cpu8692Default(5), cpu8692SuperMezz(6), cpu8695Default(7), cpu8895Default(8), undefined(255)

rc2kCPUTypeSecondary		1.3.6.1.4.1.2272.1.100.12.2
Used to identify the type of secondary CPU
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	cpu8690Default(1), cpu8690Upgrade(2), cpu8691Default(3), cpu8691Upgrade(4), cpu8692Default(5), cpu8692SuperMezz(6), cpu8695Default(7), cpu8895Default(8), undefined(255)

rc2kCPUTypePrimaryMemory		1.3.6.1.4.1.2272.1.100.12.3
Used to get the memory size of Primary CPU
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	mem64MB(1), mem128MB(2), mem256MB(3), mem512MB(4), mem1024MB(5), undefined(255)

rc2kCPUTypeSecondaryMemory		1.3.6.1.4.1.2272.1.100.12.4
Used to get the memory size of Secondary CPU
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	mem64MB(1), mem128MB(2), mem256MB(3), mem512MB(4), mem1024MB(5), undefined(255)

rc2kCpuEthernetPortIpv6RouteTable		1.3.6.1.4.1.2272.1.100.13
2k CPU Ethernet Port Route table for Ipv6
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Rc2kCpuEthernetPortIpv6RouteEntry

rc2kCpuEthernetPortIpv6RouteEntry		1.3.6.1.4.1.2272.1.100.13.1
Entry containing information of 2k CPU Ethernet Port Ipv6
Status: current	Access: not-accessible
OBJECT-TYPE
	Rc2kCpuEthernetPortIpv6RouteEntry

rc2kCpuEthernetPortIpv6RouteNetwork		1.3.6.1.4.1.2272.1.100.13.1.1
Used to configure the ipv6 network that can be used to remotely manage this device.
Status: current	Access: not-accessible
OBJECT-TYPE
	Ipv6Address

rc2kCpuEthernetPortIpv6RoutePrefixLength		1.3.6.1.4.1.2272.1.100.13.1.2
The length of the prefix (in bits).
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	0..128

rc2kCpuEthernetPortIpv6RouteGateway		1.3.6.1.4.1.2272.1.100.13.1.3
Used to configure the the IPv6 address of the gateway that should be used to forward IPv6 traffic.
Status: current	Access: not-accessible
OBJECT-TYPE
	Ipv6Address

rc2kCpuEthernetPortIpv6RouteRowStatus		1.3.6.1.4.1.2272.1.100.13.1.4
row status
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcTengEnetStats		1.3.6.1.4.1.2272.1.50.1
OBJECT IDENTIFIER

rcWisTrap		1.3.6.1.4.1.2272.1.50.2
OBJECT IDENTIFIER

rcWisSonetTrapType		1.3.6.1.4.1.2272.1.50.2.1
Used to indicate a particular type of 10GE Sonet trap.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	sectionAlarm(1), lineAlarm(2), pathAlarm(3)

rcWisSonetTrapIndication		1.3.6.1.4.1.2272.1.50.2.2
Used to indicate an indication for a 10GE Sonet trap.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	noDefect(1), sectionLossOfSignal(2), sectionLossOfFrame(3), lineAlarmIndication(4), lineRemoteDefectIndication(5), pathLossOfPointer(6), pathAlarmIndication(7), pathRemoteDefectIndication(8), pathUnequipped(9), pathSignalLabelMismatch(10), pathTraceMismatch(11)

rcTengDot3StatsTable		1.3.6.1.4.1.2272.1.50.1.1
Statistics for a collection of ethernet-like interfaces attached to a particular system.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcTengDot3StatsEntry

rcTengDot3StatsEntry		1.3.6.1.4.1.2272.1.50.1.1.1
Statistics for a particular interface to an ethernet-like medium.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcTengDot3StatsEntry

rcTengDot3StatsIndex		1.3.6.1.4.1.2272.1.50.1.1.1.1
An index value that uniquely identifies an interface to an ethernet-like medium. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

rcTengDot3StatsAlignmentErrors		1.3.6.1.4.1.2272.1.50.1.1.1.2
A count of frames received on a particular interface that are not an integral number of octets in length and do not pass the FCS check. The count represented by an instance of this object is incremented when the alignmentError status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions obtain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcTengDot3StatsFCSErrors		1.3.6.1.4.1.2272.1.50.1.1.1.3
A count of frames received on a particular interface that are an integral number of octets in length but do not pass the FCS check. The count represented by an instance of this object is incremented when the frameCheckError status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions obtain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcTengDot3StatsSingleCollisionFrames		1.3.6.1.4.1.2272.1.50.1.1.1.4
A count of successfully transmitted frames on a particular interface for which transmission is inhibited by exactly one collision. A frame that is counted by an instance of this object is also counted by the corresponding instance of either the ifOutUcastPkts, ifOutMulticastPkts, or ifOutBroadcastPkts, and is not counted by the corresponding instance of the dot3StatsMultipleCollisionFrames object.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcTengDot3StatsMultipleCollisionFrames		1.3.6.1.4.1.2272.1.50.1.1.1.5
A count of successfully transmitted frames on a particular interface for which transmission is inhibited by more than one collision. A frame that is counted by an instance of this object is also counted by the corresponding instance of either the ifOutUcastPkts, ifOutMulticastPkts, or ifOutBroadcastPkts, and is not counted by the corresponding instance of the dot3StatsSingleCollisionFrames object.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcTengDot3StatsSQETestErrors		1.3.6.1.4.1.2272.1.50.1.1.1.6
A count of times that the SQE TEST ERROR message is generated by the PLS sublayer for a particular interface. The SQE TEST ERROR message is defined in section 7.2.2.2.4 of ANSI/IEEE 802.3-1985 and its generation is described in section 7.2.4.6 of the same document.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcTengDot3StatsDeferredTransmissions		1.3.6.1.4.1.2272.1.50.1.1.1.7
A count of frames for which the first transmission attempt on a particular interface is delayed because the medium is busy. The count represented by an instance of this object does not include frames involved in collisions.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcTengDot3StatsLateCollisions		1.3.6.1.4.1.2272.1.50.1.1.1.8
The number of times that a collision is detected on a particular interface later than 512 bit-times into the transmission of a packet. Five hundred and twelve bit-times corresponds to 51.2 microseconds on a 10 Mbit/s system. A (late) collision included in a count represented by an instance of this object is also considered as a (generic) collision for purposes of other collision-related statistics.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcTengDot3StatsExcessiveCollisions		1.3.6.1.4.1.2272.1.50.1.1.1.9
A count of frames for which transmission on a particular interface fails due to excessive collisions.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcTengDot3StatsInternalMacTransmitErrors		1.3.6.1.4.1.2272.1.50.1.1.1.10
A count of frames for which transmission on a particular interface fails due to an internal MAC sublayer transmit error. A frame is only counted by an instance of this object if it is not counted by the corresponding instance of either the rcTengDot3StatsLateCollisions object, the rcTengDot3StatsExcessiveCollisions object, or the rcTengDot3StatsCarrierSenseErrors object. The precise meaning of the count represented by an instance of this object is implementation- specific. In particular, an instance of this object may represent a count of transmission errors on a particular interface that are not otherwise counted.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcTengDot3StatsCarrierSenseErrors		1.3.6.1.4.1.2272.1.50.1.1.1.11
The number of times that the carrier sense condition was lost or never asserted when attempting to transmit a frame on a particular interface. The count represented by an instance of this object is incremented at most once per transmission attempt, even if the carrier sense condition fluctuates during a transmission attempt.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcTengDot3StatsFrameTooLongs		1.3.6.1.4.1.2272.1.50.1.1.1.13
A count of frames received on a particular interface that exceed the maximum permitted frame size. The count represented by an instance of this object is incremented when the frameTooLong status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions obtain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcTengDot3StatsInternalMacReceiveErrors		1.3.6.1.4.1.2272.1.50.1.1.1.16
A count of frames for which reception on a particular interface fails due to an internal MAC sublayer receive error. A frame is only counted by an instance of this object if it is not counted by the corresponding instance of either the rcTengDot3StatsFrameTooLongs object, the rcTengDot3StatsAlignmentErrors object, or the rcTengDot3StatsFCSErrors object. The precise meaning of the count represented by an instance of this object is implementation- specific. In particular, an instance of this object may represent a count of receive errors on a particular interface that are not otherwise counted.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcTengDot3StatsEtherChipSet		1.3.6.1.4.1.2272.1.50.1.1.1.17
This object contains an OBJECT IDENTIFIER which identifies the chipset used to realize the interface. Ethernet-like interfaces are typically built out of several different chips. The MIB implementor is presented with a decision of which chip to identify via this object. The implementor should identify the chip which is usually called the Medium Access Control chip. If no such chip is easily identifiable, the implementor should identify the chip which actually gathers the transmit and receive statistics and error indications. This would allow a manager station to correlate the statistics and the chip generating them, giving it the ability to take into account any known anomalies in the chip.
Status: current	Access: read-only
OBJECT-TYPE
	OBJECT IDENTIFIER

rcTengDot3StatsLinkFailures		1.3.6.1.4.1.2272.1.50.1.1.1.18
The total number of link failures enCounter32ed on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcTengDot3StatsPacketErrors		1.3.6.1.4.1.2272.1.50.1.1.1.19
The total number of packet errors enCounter32ed on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcTengDot3StatsCarrierErrors		1.3.6.1.4.1.2272.1.50.1.1.1.20
The total number of carrier errors enCounter32ed on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcTengDot3StatsLinkInactiveErrors		1.3.6.1.4.1.2272.1.50.1.1.1.21
The total number of link inactive errors enCounter32ed on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcTengDot3StatsInFlowCtrlPkts		1.3.6.1.4.1.2272.1.50.1.1.1.22
The total number of flow control packets received by this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcTengDot3StatsOutFlowCtrlPkts		1.3.6.1.4.1.2272.1.50.1.1.1.23
The total number of flow control packets transmitted by this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcTengDot3StatsFrameTooShorts		1.3.6.1.4.1.2272.1.50.1.1.1.24
The total number of frames that are too short that were enCounter32ed on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcTengStatTable		1.3.6.1.4.1.2272.1.50.1.2
A table used to store port statistics.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcTengStatEntry

rcTengStatEntry		1.3.6.1.4.1.2272.1.50.1.2.1
interface Counter32s
Status: current	Access: not-accessible
OBJECT-TYPE
	RcTengStatEntry

rcTengStatIndex		1.3.6.1.4.1.2272.1.50.1.2.1.1
An index value that uniquely identifies a port. This value is similar to ifIndex in MIB2.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

rcTengStatBridgeInUnicastFrames		1.3.6.1.4.1.2272.1.50.1.2.1.2
The total number of incoming unicast frames that were bridged.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcTengStatBridgeInMulticastFrames		1.3.6.1.4.1.2272.1.50.1.2.1.3
The total number of incoming multicast frames that were bridged.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcTengStatBridgeInBroadcastFrames		1.3.6.1.4.1.2272.1.50.1.2.1.4
The total number of incoming broadcast frames that were bridged.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcTengStatBridgeInDiscards		1.3.6.1.4.1.2272.1.50.1.2.1.5
The total number of frames that were discarded by the bridging entity.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcTengStatBridgeOutUnicastFrames		1.3.6.1.4.1.2272.1.50.1.2.1.6
The total number of outgoing unicast frames that were bridged.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcTengStatBridgeOutMulticastFrames		1.3.6.1.4.1.2272.1.50.1.2.1.7
The total number of outgoing multicast frames that were bridged.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcTengStatBridgeOutBroadcastFrames		1.3.6.1.4.1.2272.1.50.1.2.1.8
The total number of outgoing broadcast frames that were bridged.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcTengStatRouteInUnicastFrames		1.3.6.1.4.1.2272.1.50.1.2.1.9
The total number of incoming unicast frames that were routed.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcTengStatRouteInMulticastFrames		1.3.6.1.4.1.2272.1.50.1.2.1.10
The total number of incoming multicast frames that were routed.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcTengStatRouteInDiscards		1.3.6.1.4.1.2272.1.50.1.2.1.11
The total number of frames that were discarded by the routing entity.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcTengStatRouteOutUnicastFrames		1.3.6.1.4.1.2272.1.50.1.2.1.12
The total number of outgoing unicast frames that were routed.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcTengStatRouteOutMulticastFrames		1.3.6.1.4.1.2272.1.50.1.2.1.13
The total number of outgoing multicast frames that were routed.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcTengStatStgForwardTransitions		1.3.6.1.4.1.2272.1.50.1.2.1.14
The number of times this port has transitioned from the Learning state to the Forwarding state.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcTengStatStgInConfigBpdus		1.3.6.1.4.1.2272.1.50.1.2.1.15
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcTengStatStgInTcnBpdus		1.3.6.1.4.1.2272.1.50.1.2.1.16
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcTengStatStgInBadBpdus		1.3.6.1.4.1.2272.1.50.1.2.1.17
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcTengStatStgOutConfigBpdus		1.3.6.1.4.1.2272.1.50.1.2.1.18
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcTengStatStgOutTcnBpdus		1.3.6.1.4.1.2272.1.50.1.2.1.19
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcTengStatBridgeOutFrames		1.3.6.1.4.1.2272.1.50.1.2.1.20
Used by the Accelar 8000 product family to account for all transmitted bridge unicast, broadcast, and multicast packets. The individual Counter32s are not supported.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcTengIfTable		1.3.6.1.4.1.2272.1.50.1.3
A list of interface entries. The number of entries is given by the value of engIfNumber.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcTengIfEntry

rcTengIfEntry		1.3.6.1.4.1.2272.1.50.1.3.1
An entry containing management information applicable to a particular interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcTengIfEntry

rcTengIfIndex		1.3.6.1.4.1.2272.1.50.1.3.1.1
A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcTengIfDescr		1.3.6.1.4.1.2272.1.50.1.3.1.2
A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the interface hardware/software.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

rcTengIfType		1.3.6.1.4.1.2272.1.50.1.3.1.3
The type of interface. Additional values for IfType are assigned by the Internet Assigned Numbers Authority (IANA), through updating the syntax of the IANAifType textual convention.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), regular1822(2), hdh1822(3), ddnX25(4), rfc877x25(5), ethernetCsmacd(6), iso88023Csmacd(7), iso88024TokenBus(8), iso88025TokenRing(9), iso88026Man(10), starLan(11), proteon10Mbit(12), proteon80Mbit(13), hyperchannel(14), fddi(15), lapb(16), sdlc(17), ds1(18), e1(19), basicISDN(20), primaryISDN(21), propPointToPointSerial(22), ppp(23), softwareLoopback(24), eon(25), ethernet3Mbit(26), nsip(27), slip(28), ultra(29), ds3(30), sip(31), frameRelay(32), rs232(33), para(34), arcnet(35), arcnetPlus(36), atm(37), miox25(38), sonet(39), x25ple(40), iso88022llc(41), localTalk(42), smdsDxi(43), frameRelayService(44), v35(45), hssi(46), hippi(47), modem(48), aal5(49), sonetPath(50), sonetVT(51), smdsIcip(52), propVirtual(53), propMultiplexor(54)

rcTengIfMtu		1.3.6.1.4.1.2272.1.50.1.3.1.4
The size of the largest packet which can be sent/received on the interface, specified in octets. For interfaces that are used for transmitting network datagrams, this is the size of the largest network datagram that can be sent on the interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcTengIfSpeed		1.3.6.1.4.1.2272.1.50.1.3.1.5
An estimate of the interface's current bandwidth in bits per second. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this object should contain the nominal bandwidth. If the bandwidth of the interface is greater than the maximum value reportable by this object then this object should report its maximum value (4,294,967,295) and ifHighSpeed must be used to report the interace's speed. For a sub-layer which has no concept of bandwidth, this object should be zero.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcTengIfPhysAddress		1.3.6.1.4.1.2272.1.50.1.3.1.6
The interface's address at its protocol sub-layer. The interface's media-specific MIB must define the bit and byte ordering and format of the value contained by this object. For interfaces which do not have such an address (e.g., a serial line), this object should contain an octet string of zero length.
Status: current	Access: read-only
OBJECT-TYPE
	PhysAddress

rcTengIfAdminStatus		1.3.6.1.4.1.2272.1.50.1.3.1.7
The desired state of the interface. The testing(3) state indicates that no operational packets can be passed. When a managed system initializes, all interfaces start with IfAdminStatus in the down(2) state. As a result of either explicit management action or per configuration information retained by the managed system, IfAdminStatus is then changed to either the up(1) or testing(3) states (or remains in the down(2) state).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	up(1), down(2), testing(3)

rcTengIfOperStatus		1.3.6.1.4.1.2272.1.50.1.3.1.8
The current operational state of the interface. The testing(3) state indicates that no operational packets can be passed. If IfAdminStatus is down(2) then IfOperStatus should be down(2). If IfAdminStatus is changed to up(1) then ifOperStatus should change to up(1) if the interface is ready to transmit and receive network traffic; it should change to dormant(5) if the interface is waiting for external actions (such as a serial line waiting for an incomming connection); it should remain in the down(2) state if and only if there is a fault that prevents if from going to the up(1) state.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2), testing(3), unknown(4), dormant(5)

rcTengIfLastChange		1.3.6.1.4.1.2272.1.50.1.3.1.9
The value of sysUpTime at the time the interface entered its current operational state. If the current state was entered prior to the last re-initialization of the local network management subsystem, then this object contains a zero value.
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

rcTengIfInOctets		1.3.6.1.4.1.2272.1.50.1.3.1.10
The total number of octets received on the interface, including framing characters.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcTengIfInUcastPkts		1.3.6.1.4.1.2272.1.50.1.3.1.11
The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were not addressed to a multicast or broadcast address at this sub-layer.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcTengIfInNUcastPkts		1.3.6.1.4.1.2272.1.50.1.3.1.12
The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast or broadcast address at this sub-layer. This object is deprecated in favour of IfInMulticastPkts and IfInBroadcastPkts.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter64

rcTengIfInDiscards		1.3.6.1.4.1.2272.1.50.1.3.1.13
The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcTengIfInErrors		1.3.6.1.4.1.2272.1.50.1.3.1.14
For packet-oriented interfaces, the number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. For character-oriented or fixed-length interfaces, the number of inbound transmission units that contained errors preventing them from being deliverable to a higher-layer protocol.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcTengIfInUnknownProtos		1.3.6.1.4.1.2272.1.50.1.3.1.15
For packet-oriented interfaces, the number of packets received via the interface which were discarded because of an unknown or unsupported protocol. For character-oriented or fixed-length interfaces which support protocol multiplexing the number of transmission units received via the interface which were discarded because of an unknown or unsupported protocol. For any interface which does not support protocol multiplexing, this counter will always be 0.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcTengIfOutOctets		1.3.6.1.4.1.2272.1.50.1.3.1.16
The total number of octets transmitted out of the interface, including framing characters.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcTengIfOutUcastPkts		1.3.6.1.4.1.2272.1.50.1.3.1.17
The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcTengIfOutNUcastPkts		1.3.6.1.4.1.2272.1.50.1.3.1.18
The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent. This object is deprecated in favour of IfOutMulticastPkts and IfOutBroadcastPkts.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter64

rcTengIfOutDiscards		1.3.6.1.4.1.2272.1.50.1.3.1.19
The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcTengIfOutErrors		1.3.6.1.4.1.2272.1.50.1.3.1.20
For packet-oriented interfaces, the number of outbound packets that could not be transmitted because of errors. For character-oriented or fixed-length interfaces, the number of outbound transmission units that could not be transmitted because of errors.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcTengIfOutQLen		1.3.6.1.4.1.2272.1.50.1.3.1.21
The length of the output packet queue (in packets).
Status: deprecated	Access: read-only
OBJECT-TYPE
	Gauge32

rcTengIfSpecific		1.3.6.1.4.1.2272.1.50.1.3.1.22
A reference to MIB definitions specific to the particular media being used to realize the interface. It is recommended that this value point to an instance of a MIB object in the media-specific MIB, i.e., that this object have the semantics associated with the InstancePointer textual convention defined in RFC 1443. In fact, it is recommended that the media- specific MIB specify what value ifSpecific should/can take for values of ifType. If no MIB definitions specific to the particular media are available, the value should be set to the OBJECT IDENTIFIER { 0 0 }.
Status: deprecated	Access: read-only
OBJECT-TYPE
	OBJECT IDENTIFIER

rcTengIfXTable		1.3.6.1.4.1.2272.1.50.1.4
A list of interface entries. The number of entries is given by the value of ifNumber. This table contains additional objects for the interface table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcTengIfXEntry

rcTengIfXEntry		1.3.6.1.4.1.2272.1.50.1.4.1
An entry containing additional management information applicable to a particular interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcTengIfXEntry

rcTengIfXIndex		1.3.6.1.4.1.2272.1.50.1.4.1.1
A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcTengIfName		1.3.6.1.4.1.2272.1.50.1.4.1.2
The textual name of the interface. The value of this object should be the name of the interface as assigned by the local device and should be suitable for use in commands entered at the device's `console'. This might be a text name, such as `le0' or a simple port number, such as `1', depending on the interface naming syntax of the device. If several entries in the rcTengIfTable together represent a single interface as named by the device, then each will have the same value of rcTengIfName. If there is no local name, or this object is otherwise not applicable, then this object contains a 0-length string.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

rcTengIfInMulticastPkts		1.3.6.1.4.1.2272.1.50.1.4.1.3
The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast address at this sub-layer. For a MAC layer protocol, this includes both Group and Functional addresses.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcTengIfInBroadcastPkts		1.3.6.1.4.1.2272.1.50.1.4.1.4
The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcTengIfOutMulticastPkts		1.3.6.1.4.1.2272.1.50.1.4.1.5
The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast address at this sub-layer, including those that were discarded or not sent. For a MAC layer protocol, this includes both Group and Functional addresses.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcTengIfOutBroadcastPkts		1.3.6.1.4.1.2272.1.50.1.4.1.6
The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a broadcast address at this sub-layer, including those that were discarded or not sent.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcTengIfHCInOctets		1.3.6.1.4.1.2272.1.50.1.4.1.7
The total number of octets received on the interface, including framing characters. This object is a 64-bit version of rcTengIfInOctets.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcTengIfHCInUcastPkts		1.3.6.1.4.1.2272.1.50.1.4.1.8
The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were not addressed to a multicast or broadcast address at this sub-layer. This object is a 64-bit version of rcTengIfInUcastPkts.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcTengIfHCInMulticastPkts		1.3.6.1.4.1.2272.1.50.1.4.1.9
The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast address at this sub-layer. For a MAC layer protocol, this includes both Group and Functional addresses. This object is a 64-bit version of rcTengIfInMulticastPkts.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcTengIfHCInBroadcastPkts		1.3.6.1.4.1.2272.1.50.1.4.1.10
The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer. This object is a 64-bit version of IfInBroadcastPkts.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcTengIfHCOutOctets		1.3.6.1.4.1.2272.1.50.1.4.1.11
The total number of octets transmitted out of the interface, including framing characters. This object is a 64-bit version of rcTengIfOutOctets.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcTengIfHCOutUcastPkts		1.3.6.1.4.1.2272.1.50.1.4.1.12
The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent. This object is a 64-bit version of rcTengIfOutUcastPkts.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcTengIfHCOutMulticastPkts		1.3.6.1.4.1.2272.1.50.1.4.1.13
The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast address at this sub-layer, including those that were discarded or not sent. For a MAC layer protocol, this includes both Group and Functional addresses. This object is a 64-bit version of rcTengIfOutMulticastPkts.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcTengIfHCOutBroadcastPkts		1.3.6.1.4.1.2272.1.50.1.4.1.14
The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a broadcast address at this sub-layer, including those that were discarded or not sent. This object is a 64-bit version of rcTengIfOutBroadcastPkts.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcTengIfLinkUpDownTrapEnable		1.3.6.1.4.1.2272.1.50.1.4.1.15
Indicates whether linkUp/linkDown traps should be generated for this interface. By default, this object should have the value enabled(1) for interfaces which do not operate on 'top' of any other interface (as defined in the rcTengIfStackTable), and disabled(2) otherwise.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

rcTengIfHighSpeed		1.3.6.1.4.1.2272.1.50.1.4.1.16
An estimate of the interface's current bandwidth in units of 1,000,000 bits per second. If this object reports a value of `n' then the speed of the interface is somewhere in the range of `n-500,000' to `n+499,999'. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this object should contain the nominal bandwidth. For a sub-layer which has no concept of bandwidth, this object should be zero.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

rcTengIfPromiscuousMode		1.3.6.1.4.1.2272.1.50.1.4.1.17
This object has a value of false(2) If this interface only accepts packets/frames that are addressed to this station. This object has a value of true(1) when the station accepts all packets/frames transmitted on the media. The value true(1) is only legal on certain types of media. If legal, setting this object to a value of true(1) may require the interface to be reset before becoming effective. The value of rcTengIfPromiscuousMode does not affect the reception of broadcast and multicast packets/frames by the interface.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcTengIfConnectorPresent		1.3.6.1.4.1.2272.1.50.1.4.1.18
This object has the value 'true(1)' if the interface sublayer has a physical connector and the value 'false(2)' otherwise.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcRecReservTable		1.3.6.1.4.1.2272.1.51.1
This table would display the statistics of several HW record type used. This will also let the user reserve certain number of records for each type.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcRecReservEntry

rcRecReservTablEntry		1.3.6.1.4.1.2272.1.51.1.1
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	RcRecReservEntry

rcRecReservRecordType		1.3.6.1.4.1.2272.1.51.1.1.1
.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	filter(1), ipmc(2), local(3), mac(4), static(5), vrrp(6)

rcRecReservUsed		1.3.6.1.4.1.2272.1.51.1.1.2
Displayes the number of HW records actually usee by the recordType.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcRecReservReserved		1.3.6.1.4.1.2272.1.51.1.1.3
Displayes the number of HW records reserved for the recordType.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcRecReservNewReserved		1.3.6.1.4.1.2272.1.51.1.1.4
Displayes the number of HW records that w ill be reserved for this recordType after reset if the configuration is saved.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcRecReservDefReserved		1.3.6.1.4.1.2272.1.51.1.1.5
Number of records reserved for this recordType if loaded with factory default.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcSshGlobal		1.3.6.1.4.1.2272.1.34.1
OBJECT IDENTIFIER

rcSshGlobalVersion		1.3.6.1.4.1.2272.1.34.1.1
SSH version
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	v2only(1), both(2)

rcSshGlobalPort		1.3.6.1.4.1.2272.1.34.1.2
SSH connection port.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcSshGlobalMaxSession		1.3.6.1.4.1.2272.1.34.1.3
Number of session allowed.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..8

rcSshGlobalTimeout		1.3.6.1.4.1.2272.1.34.1.4
SSH connection timeout in seconds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..120

rcSshGlobalRsaKeySize		1.3.6.1.4.1.2272.1.34.1.5
SSH Rsa key size.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	512..1024

rcSshGlobalDsaKeySize		1.3.6.1.4.1.2272.1.34.1.6
SSH Dsa key size.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	512..1024

rcSshGlobalRsaAuth		1.3.6.1.4.1.2272.1.34.1.7
Enable/disable SSH RSA authentication
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcSshGlobalDsaAuth		1.3.6.1.4.1.2272.1.34.1.8
Enable/disable SSH DSA authentication
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcSshGlobalPassAuth		1.3.6.1.4.1.2272.1.34.1.9
Enable/disable SSH RSA authentication
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcSshGlobalKeyAction		1.3.6.1.4.1.2272.1.34.1.10
SSH key action.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), generateDsa(1), generateRsa(2), deleteDsa(3), deleteRsa(4)

rcSshGlobalEnable		1.3.6.1.4.1.2272.1.34.1.11
Enable/disable, or securely enable SSH. Securely enable turns off other daemon flag, and it takes ffect afte reboot
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	false(0), true(1), secure(2)

rcLicenseNumber		1.3.6.1.4.1.2272.1.56.1
Bit position number of license bitmap
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	bit8600BASE(0), bitPP8300BASE(2), bitdellBASE(3), bit8xx4BASE(4), bit8xx5BASE(5), bit8xx6BASE(6), bit8xx7BASE(7), bit8xx8BASE(8), bit8xx9BASE(9), bit8x10BASE(10), bit8x11BASE(11), bit8x12BASE(12), bit8x13BASE(13), bit8x14BASE(14), bit8x15BASE(15), bit8x16BASE(16), bit8x17BASE(17), bit8x18BASE(18), bit8x19BASE(19), bit8x20BASE(20), bit8x21BASE(21), bit8x22BASE(22), bit8x23BASE(23), bit8x24BASE(24), bit8x25BASE(25), bit8x26BASE(26), bit8x27BASE(27), bit8x28BASE(28), bit8x29BASE(29), bit8x30BASE(30), bit8x31BASE(31), bitpackageStart(32), bitBASIC(33), bitUNICAST(34), bitMULTICAST(35), bitTOOL(36), bitADVANCED(37), bitPREMIER(39), bitpackageEnd(255), bitfeature(256), bitrc2kCopyFileGrp(257), bitrc2kDeviceGlobalTbl(258), bitrcCliCustomGrp(259), bitrcCliGrp(260), bitrcCliGrpWsm(261), bitrcDiagMacConvSteeringTbl(262), bitrcDiagMirrorByPortTbl(263), bitrcDiagPortConvSteeringTbl(264), bitrcSysAccPolicyTbl(265), bitrcSysGrp(266), bitrcSysTrapTbl(267), bitrcUserSetTimeGrp(268), bitrcPortLock(269), bitrcSyslogGlobalGrp(270), bitrcSyslogHostTbl(271), bitrcWebGrp(272), bitdot1dStaticEntry(273), bitsnmpCommunityTbl(274), bitrcLoadModule(275), bitrcMltGrp(276), bitrcMltTbl(277), bitsmltMacTblSend(278), bitrc2kQosEgressQosToDscpTbl(279), bitrc2kQosEgressQosToTagTbl(280), bitrc2kQosIngressDscpToQosTbl(281), bitrc2kQosIngressTagToQosTbl(282), bitrc2kQosQosTbl(283), bitrcBridgeAutoLearnTbl(284), bitrcBridgeManualEditTbl(285), bitrcBridgeUnknownMacDiscardTbl(286), bitrcBridgeStaticMulticastTbl(287), bitrcSvlanGlobalGrp(288), bitrcSvlanTbl(289), bitrcVlanMacTbl(290), bitrcVlanPortTbl(291), bitrcVlanTbl(292), bitvlanTbl(293), bitrc2kBootConfigTbl(294), bitrc2kCpuEthernetPortRouteTbl(295), bitrc2kCpuEthernetPortTbl(296), bitrc2kCpuSerialPortTbl(297), bitrc2kCardTbl(298), bitrc2kMdaCardTbl(299), bitrcChassisGrp(300), bitrcL2RedundancyGrp(301), bitrcRecReservTbl(302), bitrcTftpGrp(303), bitrcFdbTbl(304), bitrcFilterTbl(305), bitrcStaticTbl(306), bitmgMirror(307), bitifTbl(308), bitifTestTbl(309), bitrcChassisPort(310), bitrcRateLimitTbl(311), bitrcTengIfTbl(312), bitrcLinkFlapDetectGrp(313), bitifTblMlt(314), bitposIfTbl(315), bitpppBridgeConfigTbl(316), bitpppIpConfigTbl(317), bitpppLinkConfigTbl(318), bitpppLqrConfigTbl(319), bitrcPosLineConfigTbl(320), bitrcPosPppIpxTbl(321), bitrcPosSioCardConfigTbl(322), bitrcPosSonetTbl(323), bitatm1483ElanTbl(324), bitatmPortTbl(325), bitatmPvcTbl(326), bitrc2kAtm1483ElanTbl(327), bitrc2kAtmPortTbl(328), bitrc2kAtmPvcTbl(329), bitrc2kAtmSioCardConfigTbl(330), bitbrdgStp(331), bitbrdgStpPortTbl(332), bitrcStg(333), bitrcStgPortTbl(334), bitrcStgTbl(335), bitigmpInterfaceTbl(336), bitrcIgmpAccessTbl(337), bitrcIgmpInterfaceExtnTbl(338), bitrcIgmpSenderTbl(339), bitrcIgmpStaticTbl(340), bitipfFilterModifyDs(341), bitrc2kQosTrafficProfileTbl(342), bitrcIpFilterBaseListTbl(343), bitrcIpFilterGlobalListTbl(344), bitrcIpFilterMediaDevTbl(345), bitrcIpFilterMediaStreamTbl(346), bitrcIpFilterPortTbl(347), bitrcIpFilterTbl(348), bitrcIpMulticastSoftwareForwardingGrp(349), bitrcIpMulticastTimedPruneTbl(350), bitrcMltMcastDistributionGrp(351), bitipMRouteInterfaceTbl(352), bitdvmrpInterfaceTbl(353), bitpimCandidateRPTbl(354), bitpimGrp(355), bitpimInterfaceTbl(356), bitrcNtpGlobalGrp(357), bitrcNtpKeyTbl(358), bitrcNtpServerTbl(359), bitospfAreaAggregateTbl(360), bitospfAreaTbl(361), bitospfGeneralGrp(362), bitospfHostTbl(363), bitospfIfMetricTbl(364), bitospfIfTbl(365), bitospfNbrTbl(366), bitospfStubAreaTbl(367), bitospfVirtIfTbl(368), bitwfPgmGrp(369), bitwfPgmIfTbl(370), bitwfPgmSessionTbl(371), bitrcRadiusGlobalGrp(372), bitrcRadiusServerTbl(373), bitrcIpFlowTbl(374), bitrcIpConfDhcpTbl(375), bitrcIpDhcpForwardTbl(376), bitrcIpConfDvmrpTbl(377), bitrcIpDvmrpGrp(378), bitrcArpExtTbl(379), bitrcIpAddrTbl(380), bitrcIpConfGlobalGrp(381), bitrcIpConfIcmpRdiscTbl(382), bitrcIpConfTbl(383), bitrcIpMulticastArpTbl(384), bitrcIpRoutePrefTbl(385), bitrcRipExtTbl(386), bitrcIpConfOspfAreaAggregateTbl(387), bitrcIpConfOspfAreaTbl(388), bitrcIpConfOspfTbl(389), bitrcIpPimGlobalGrp(390), bitrcIpPimStaticRPTbl(391), bitrcIpPimTbl(392), bitrcIpRipInterfaceTbl(393), bitrcIpRouteTbl(394), bitrcIpStaticRouteTbl(395), bittcpConnTbl(396), bitrcIpUdpConfBroadcastIntfTbl(397), bitrcIpUdpPortFwdListTbl(398), bitrcIpUdpPortFwdTbl(399), bitrcIpUdpProtocolTbl(400), bitvrrpAssoIpAddrTbl(401), bitvrrpOperTbl(402), bitvrrpOperationsGrp(403), bitvrrpRouterStatsTbl(404), bitrcIpxAddrTbl(405), bitrcIpxBrouterTbl(406), bitrcIpxGrp(407), bitrcIpxPolicyListTbl(408), bitrcIpxPolicyNetTbl(409), bitrcIpxPolicyServTbl(410), bitrcIpxRipInFilterTbl(411), bitrcIpxRipInterfaceTbl(412), bitrcIpxRipOutFilterTbl(413), bitrcIpxSapInFilterTbl(414), bitrcIpxSapInterfaceTbl(415), bitrcIpxSapOutFilterTbl(416), bitvlanEncap(417), bitrcIpAsPathAccessListTbl(418), bitrcIpCommunityAccessListTbl(419), bitrcIpGenPolicyGrp(420), bitrcIpOspfInFilterTbl(421), bitrcIpPrefixListTbl(422), bitrcIpRedistributeTbl(423), bitrcIpRoutePolicyStrEnt(424), bitrcIpRoutePolicyTbl(425), bits5EnMsTopInfoGrp(426), bitbgpPeerTbl(427), bitrcIpBgpAggregateTbl(428), bitrcIpBgpConfederationGrp(429), bitrcIpBgpGeneralGrp(430), bitrcIpBgpNetworkTbl(431), bitrcIpBgpPeerGroupTbl(432), bitrcIpBgpPeerTbl(433), bitrcIpBgpRouteReflectorGrp(434), bitrcStatBgpGrp(435), bitrcStatBgpPeerTbl(436), bitrcSshGlobalGrp(437), bitrcDiagPcapAdvancedFilterTbl(438), bitrcDiagPcapFilterTbl(439), bitrcDiagPcapGrp(440), bitrcPortPcapTbl(441), bitrcArpExtEntDoProxy(442), bitrcIpConfGlobalRouteDiscovery(443), bitSuperNetEnable(444), bitospfCli(445), bitTreeCli(446), bitShowCmdCli(447), bitInfoCmdCli(448), bitrcIgmpChannelLimitTbl(449), bitrcIgmpSsmTbl(450), bitrcIgmpSsmGlobalGrp(451), bitrcIgmpIgapGlobalGrp(452), bitrcIgmpGlobalParamsGrp(453), bitrcRadiusGlobalSnmpGrp(454), bitrcSltPortTbl(455), bitrcErrorGrp(456), bitrcIgmpIgapServiceAbilityTbl(457), bitrcVlanDsapSsapTbl(458), bitrcIpArpCliClearPortCli(459), bitrcIpArpCliClearVlanCli(460), bitrcIpArpCliAddCli(461), bitrcIpArpCliDeleteCli(462), bitrcIpMulticastMacFloodingCliEnableCli(463), bitcliMacFlapTimeLimitSetCli(464), bitcliWriteRtcCli(465), bitipfCliClearStatsCli(466), bitipxCliDisableGnsCli(467), bitipxCliDisableRipCli(468), bitipxCliDisableRouteCli(469), bitipxCliDisableSapCli(470), bitipxCliRipSetDefDelayTimerCli(471), bitipxCliRipSetHoldMultiplierCli(472), bitipxCliRipSetDefIntervalTimerCli(473), bitipxCliEnableGnsCli(474), bitipxCliEnableRipCli(475), bitipxCliEnableSapCli(476), bitipxCliDisableRoute(477), bitipxCliEnableRouteCli(478), bitipxCliRipStateCli(479), bitipxCliRipSetDelayTimerCli(480), bitipxCliRipSetIntervalTimerCli(481), bitipxCliSapAddStaticEntryCli(482), bitipxCliSapDeleteStaticEntryCli(483), bitipxCliSapSetDefDelayTimerCli(484), bitipxCliSapSetDefHoldMultiplierCli(485), bitipxCliSapSetDefIntervalTimerCli(486), bitipxCliSapSetHoldMultiplierCli(487), bitipxCliSapSetGnsTieBreakerCli(488), bitipxCliSapStateCli(489), bitipxCliSapSetDelayTimerCli(490), bitipxCliSapSetIntervalTimerCli(491), bitipxCliAddRouteEntryCli(492), bitipxCliDeleteRouteEntryCli(493), bitipxCliSetMaxRouteCli(494), bitipxCliSetMaxSapCli(495), bitipxCliSetMaxStaticRouteCli(496), bitipxCliSetMaxStaticSapCli(497), bitipxCliSetNetBiosEnableDisableCli(498), bitipxCliSetLearnAfterIncrementEnableDisableCli(499), bitcliPasswordROCli(500), bitcliPasswordRWL1Cli(501), bitcliPasswordRWL2Cli(502), bitcliPasswordRWL3Cli(503), bitcliPasswordRWCli(504), bitcliPasswordRWACli(505), bitcliPasswordSLBOPERCli(506), bitcliPasswordL4OPERCli(507), bitcliPasswordOPERCli(508), bitcliPasswordSLBADMINCli(509), bitcliPasswordL4ADMINCli(510), bitcliPasswordSSLADMINCli(511), bitcliMonitorDurationCli(512), bitcliMonitorIntervalCli(513), bitcliDefaultBannerCli(514), bitcliDisplayMotdCli(515), bitcliDefaultLoginCli(516), bitcliDefaultPasswordCli(517), bitcliMoreCli(518), bitcliRloginLimitCli(519), bitcliScrsizeCli(520), bitcliTelnetLimitCli(521), bitcliTimeoutCli(522), bitlogCliHostCreateCli(523), bitlogCliSetTransferFileNameCli(524), bitlogCliHostDeleteCli(525), bitlogcliLevelCli(526), bitlogcliScreenCli(527), bitlogCliMsgOnPcmciaCli(528), bitcliAddTraceModuleCli(529), bitsetAutoTraceStatusCli(530), bitsetAutoTraceHighTrackDurationCli(531), bitsetAutoTraceLowPercentageCli(532), bitsetAutoTraceLowTrackDurationCli(533), bitcliRemTraceModuleCli(534), bitrcIpxCliPolicyTraceRipOutFilterAddCli(535), bitrcIpxCliPolicyTraceRipOutFilterDeleteCli(536), bitrcIpxCliPolicyTraceRipInFilterAddCli(537), bitrcIpxCliPolicyTraceRipInFilterDeleteCli(538), bitrcIpxCliPolicyTraceSapOutFilterAddCli(539), bitrcIpxCliPolicyTraceSapOutFilterDelete(540), bitrcIpxCliPolicyTraceSapInFilterAddCli(541), bitrcIpxCliPolicyTraceSapInFilterDeleteCli(542), bittracecliClearCli(543), bittracecliLevelCli(544), bittracecliOffCli(545), bittracecliFilterCli(546), bittracecliGrepStringCli(547), bittraceCliPolicyCli(548), bitdebugcliSlotXCli(549), bitripCliSetDefImportMetCli(550), bitripCliDisableCli(551), bitripCliDomainCli(552), bitripCliEnableCli(553), bitripCliSetIfDomainCli(554), bitripCliSetIfRxModeCli(555), bitripCliSetIfTxModeCli(556), bitripCliSetHoldDownCli(557), bitripCliReceiveCli(558), bitripCliSendCli(559), bitsysCliSetRmonAlarmCreateCli(560), bitsysCliSetRmonAlarmDeleteCli(561), bitsysCliSetRmonEventCreateCli(562), bitsysCliSetRmonEventDeleteCli(563), bitsysCliSetRmonHistoryCreateCli(564), bitsysCliSetRmonHistoryDeleteCli(565), bitsysCliSetRmonEtherCreateCli(566), bitsysCliSetRmonEtherDeleteCli(567), bitsysCliSetRmonEtherOwnerCli(568), bitcliStartAtmConsoleCli(569), bitrebootcliCli(570), bittoptreeCli(571), bitconvert11configCli(572), bitcopyimageCli(573), bitcwccliCli(574), bitshowdateCli(575), bitdirectoryCli(576), bitshowDumpAsicAddrCli(577), bitshowHwDumpAllCli(578), bitshowIcmpStatCli(579), bitshowInetStatCli(580), bitshowInspectCli(581), bitcliinstallCli(582), bitreloginCli(583), bitshowopDumpErrorRegsCli(584), bitshowOspfDumpAllCli(585), bitshowOspfDumpSpfInfoCli(586), bitpeercliCli(587), bitpingcliCli(588), bitipxCliPingCli(589), bitpwccliCli(590), bitshowrarDumpRegsCli(591), bitshowRarCheckStatsCli(592), bitshowRarErrorCountCli(593), bitshowrcDumpIfIndexCli(594), bitdeleteimageCli(595), bitresetcliCli(596), bitrlogincliCli(597), bitrshcliCli(598), bitsavecliCli(599), bitVxshellCli(600), bitclisourceCli(601), bitshowSpyReportCli(602), bitshowSwipDumpCli(603), bittelnetcliCli(604), bittracerouteCli(605), bitshowTaskTraceCli(606), bitrcIpRouteCliClearPortCli(607), bitrcIpRouteCliClearVlanCli(608), bitdumpcliArCli(609), bitmltCliClearIstStatsCli(610), bitportCliClearStatsCli(611), bitcliResetConsoleShellCli(612), bitcliKillTelnetSessionCli(613), bitatmCliClearVPortStatsCli(614), bitatmCliClearF5StatsCli(615), bitatmCliClearPortStatsCli(616), bitatmCliCardResetCli(617), bitatmCliEnableVPortStatsCli(618), bitatmCliSetDebugCli(619), bitatmCliVPortStatsIntervalCli(620), bitatmCliLaneCreateCli(621), bitatmCliLaneDeleteCli(622), bitatmCliStateCli(623), bitigmpOldCliDelAccessListCli(624), bitigmpOldCliSetAccessModeCli(625), bitposCliCardResetCli(626), bitposCliSetDebugCli(627), bitposCliSetPosConsoleCli(628), bitportCliSetLinktrapCli(629), bitportCliFlushIgmpCli(630), bitsysCliAccessEnableCli(631), bitvlanCliIeeeDiscardRecordAgingCli(632), bitvlanCliIeeeAgingDisableCli(633), bitvlanCliIeeeAgingEnableCli(634), bitsysCliSetSnmpForceTrapSenderCli(635), bitsysResetWebPasswdCli(636), bitsysResetSnmpCommStringsCli(637), bitsysCliSetMgmtVirtualIpCli(638), bitsysCliSetContactCli(639), bitsysCliSetHighPerformanceCli(640), bitsysCliSetLocationCli(641), bitsysCliSetMessageControlCli(642), bitsysCliSetChassisMTUCli(643), bitcliPromptCli(644), bitsysCliSetOctapidResetThresholdCli(645), bitsysCliSetSmltPortUnlockTimeoutCli(646), bitsysCliSetUdpSourceCli(647), bitvlanCliFlushIeeeVlanDiscardRecordsCli(648), bitposCliSetLEDCli(649), bitvlanCliRipManualTrigCli(650), bitvlanCliChangeIpxEncapCli(651), bitvlanCliSetFdbTimeOutCli(652), bitvlanCliSyncFdbCli(653), bitportCliRipManualTrigCli(654), bitportCliSetCpLimitCli(655), bitportCliSetClockSourceCli(656), bitportCliSetFlowControlCli(657), bitportCliSetFlowControlPause0Cli(658), bitportCliSetFlowControlPauseTimeCli(659), bitportCliSetSffdCli(660), bitsetMgmtIpCli(661), bitsetWsmAutoResetCli(662), bitreadWSMCommunityCli(663), bitwriteWSMCommunityCli(664), bittrapWSMCommunityCli(665), bitauthTrapWSMCli(666), bitlinkTrapWSMCli(667), bittelnetWsmCli(668), bitsyslogFacilityCli(669), bitwsmResetCli(670), bitwsmSaveCli(671), bitwsmBootChoiceCli(672), bitwsmDumpCardDBCli(673), bitwsmDumpIPTableCli(674), bitwsmDumpTableCli(675), bithiddenModeCli(676), bitresetSamCli(677), bitsamBootBackupCli(678), bitsamShowClusterCli(679), bitoldieCli(680), bitipCliSetBgpRedistApplyCli(681), bitrcBgpPeerCli(682), bitCliConfigIpBgpMaxInitPeersCli(683), bitCliConfigIpBgpMaxTxQueueLenCli(684), bitCliConfigIpBgpDebugScreenCli(685), bitpolicySetOspfAcceptPrecedenceCli(686), bitpolicySetOspfAnnouncePrecedenceCli(687), bitpolicySetRipAcceptPrecedenceCli(688), bitpolicySetRipAcceptRipIfListCli(689), bitpolicySetRipAnnounceOutIfListCli(690), bitpolicySetRipAnnouncePrecedenceCli(691), bitpolicyRipAnnounceRemoveFromRtSrcCli(692), bitospfCliModRangeEffectCli(693), bitospfCliModRangeMetricCli(694), bitospfCliSetVirtIfMd5KeyTxCli(695), bitospfCliSetIfMd5KeyCli(696), bitospfCliSetMd5KeyTxCli(697), bitospfCliDelIfMd5KeyCli(698), bitipCliSetOspfAcceptApplyCli(699), bitospfCliSetDefMetricGrpCli(700), bitospfCliSetSpfHoldDownTimeCli(701), bitospfCliSetSpfRunCli(702), bitospfCliSetTrapCli(703), bitrcIpVrrpCliClearPortCli(704), bitrcIpVrrpCliClearVlanCli(705), bitrcIpResourceUsageGlobalGrp(706), bitrcIpPimInterfaceTbl(707), bitipmcCliSetDvmGlobDisCli(708), bitipmcCliSetDvmGlobEnlCli(709), bitipmcCliSetDvmGlobLeafTimeoutCli(710), bitipmcCliSetDvmGlobNbrTimeoutCli(711), bitipmcCliSetDvmGlobNbrProbeIntCli(712), bitipmcCliSetDvmGlobTrigUpdateIntervalCli(713), bitipmcCliSetDvmGlobUpdateIntervalCli(714), bitipmcCliSetDvmGlobFwdCacheTimeoutCli(715), bitipmcCliSetDvmGlobRouteExpireTimeoutCli(716), bitipmcCliSetDvmGlobRouteDiscTimeoutCli(717), bitipmcCliSetDvmGlobRouteSwitchTimeoutCli(718), bitipmcCliSetDvmGlobShowNextHopTableCli(719), bitipCliSetPimdebugAssertCli(720), bitipCliSetPimdebugBootstrapCli(721), bitipCliSetPimdebugGroupCli(722), bitipCliSetPimdebugHelloCli(723), bitipCliSetPimdebugJoinpruneCli(724), bitipCliSetPimDbgTraceCli(725), bitipCliSetPimDbgLogCli(726), bitipCliSetPimdebugRegisterCli(727), bitipCliSetPimdebugRegStopCli(728), bitipCliSetPimdebugRpadvCli(729), bitipCliSetPimdebugSendCli(730), bitipCliSetPimdebugRcvCli(731), bitipClienabletraceforSGentryCli(732), bitipClidisabletraceforSGentryCli(733), bitipCliSetPimGlobBrDisCli(734), bitipCliSetPimGlobBrEnlCli(735), bitportCliSetPimIfCreateCli(736), bitportCliSetPimIfTypeCli(737), bitdiagCliPingSnoopAddPortsCli(738), bitdiagCliPingSnoopCreateCli(739), bitdiagCliPingSnoopDeleteCli(740), bitdiagCliPingSnoopEnaDisCli(741), bitdiagCliPingSnoopRemPortsCli(742), bitrcIpBgpPeerCli(743), bitospfCliSetVirtIfMd5KeyCli(744), bitospfCliDelVirtIfMd5KeyCli(745), bitipSetOspfRedistApplyCli(746), bitospfSetAutoVlinkCli(747), bitospfSetTrapCli(748), bitipSetPimdebugSourceCli(749), bitportCliSetLoopDetectCli(750), bitlogcliClearCli(751), bitlogcliWriteCli(752), bitsetAutoTraceHighPercentageCli(753), bittracecliScreenCli(754), bitripCliCliSetIfRxModeCli(755), bitripSetIfTxModeCli(756), bitripUpdateCli(757), bitsysCliSetSendTrapConfigCli(758), bitclilsCli(759), bitclimkdirCli(760), bittelnetSamCli(761), bitsysCliV3UserSetCli(762), bitsysCliV3GrpSetCli(763), bitsysCliV3AccessSetCli(764), bitsysCliV3NotifySetCli(765), bitsysCliV3ViewSetCli(766), bitsysCliV3TargetSetCli(767), bitsysCliV3TargetParamsSetCli(768), bitsnmpCliViewSetCli(769), bitBcli8100Cli(770), bitBcliAgentHacpuCli(771), bitBcliAttribCli(772), bitBcliAutobootCli(773), bitBcliAutonegotiateCli(774), bitBcliBaudCli(775), bitBcliBootCli(776), bitBcliBootpCli(777), bitBcliCdCli(778), bitBcliCfgfileCli(779), bitBcliCopyCli(780), bitBcliCpCli(781), bitBcliCwcCli(782), bitBcliDatabitsCli(783), bitBcliDcdebugCli(784), bitBcliDebugcfgCli(785), bitBcliDebugmodeCli(786), bitBcliDelayCli(787), bitBcliWlandesiredssidCli(788), bitBcliDirCli(789), bitBcliDosChkdskCli(790), bitBcliDosFormatCli(791), bitBcliDstCli(792), bitBcliDstendCli(793), bitBcliDstnameCli(794), bitBcliDstoffCli(795), bitBcliDststartCli(796), bitBcliDumpspromCli(797), bitBcliEditCli(798), bitBcliEgressloopCli(799), bitBcliFactorydefaultsCli(800), bitBcliFmmdebugCli(801), bitBcliFmmFormatCli(802), bitBcliFtpdCli(803), bitBcliFtpdebugCli(804), bitBcliFullduplexCli(805), bitBcliGrepCli(806), bitBcliHacpuCli(807), bitBcliI2cdebugCli(808), bitBcliImagefileCli(809), bitBcliLsCli(810), bitBcliMasterCli(811), bitBcliMcpCli(812), bitBcliMfgburninCli(813), bitBcliMfgdCli(814), bitBcliMfgledCli(815), bitBcliMfgmCli(816), bitBcliMgmtrouteCli(817), bitBcliMkdirCli(818), bitBcliMnetipCli(819), bitBcliMoreCli(820), bitBcliMoreflagCli(821), bitBcliMulticastCli(822), bitBcliMvCli(823), bitBcliNetenableCli(824), bitBcliNetipCli(825), bitBcliNetrestartCli(826), bitBcliNetspeedCli(827), bitBcliPcdebugCli(828), bitBcliPclogCli(829), bitBcliPctraceCli(830), bitBcliPeerCli(831), bitBcliPingCli(832), bitBcliProgrambootCli(833), bitBcliPromptCli(834), bitBcliPwcCli(835), bitBcliPwdCli(836), bitBcliRarudipsvCli(837), bitBcliRarudrecCli(838), bitBcliReadspromCli(839), bitBcliRebootonerrorCli(840), bitBcliResetCli(841), bitBcliResetPasswordCli(842), bitBcliRloginCli(843), bitBcliRlogindCli(844), bitBcliRloginlimitCli(845), bitBcliRmCli(846), bitBcliRshCli(847), bitBcliSaveCli(848), bitBcliSavetostandbyCli(849), bitBcliScrsizeCli(850), bitBcliSetbootpimagenameCli(851), bitBcliSioenableCli(852), bitBcliSiomodeCli(853), bitBcliSiomtuCli(854), bitBcliSiomyipCli(855), bitBcliSiopeeripCli(856), bitBcliSiopppfileCli(857), bitBcliSiorestartCli(858), bitBcliSioslipcomCli(859), bitBcliSiosliprxcomCli(860), bitBcliSnmpdCli(861), bitBcliSourceCli(862), bitBcliSshdCli(863), bitBcliTelnetCli(864), bitBcliTelnetdCli(865), bitBcliTelnetlimitCli(866), bitBcliTestCli(867), bitBcliTestspromCli(868), bitBcliTftpdCli(869), bitBcliTftpdebugCli(870), bitBcliTftphashCli(871), bitBcliTftphostCli(872), bitBcliTftprexmitCli(873), bitBcliTftptimeoutCli(874), bitBcliTimeoutCli(875), bitBcliTupleCli(876), bitBcliTzCli(877), bitBcliTzoffCli(878), bitBcliUpdatebootCli(879), bitBcliVerifycfgCli(880), bitBcliVxataCli(881), bitBcliVxdcCli(882), bitBcliVxdosCli(883), bitBcliVxinetCli(884), bitBcliVxiosCli(885), bitBcliVxmemCli(886), bitBcliVxpasswordCli(887), bitBcliVxpppCli(888), bitBcliVxtiCli(889), bitBcliVxuserCli(890), bitBcliWdtCli(891), bitBcliWlanCli(892), bitBcliWlanconfigureCli(893), bitBcliWriteRtcCli(894), bitBcliWritespromCli(895), bitBootPCliSetImageNameCli(896), bitBootPCliSettingCli(897), bitExitTreeCli(898), bitMacUpgradeCli(899), bitPcmciaStopCli(900), bitBcliPrivilegeCli(901), bitBcliReadRtcCli(902), bitShowHelpCli(903), bitShowHistoryCli(904), bitOpTreeCli(905), bitUpOneTreeCli(906), bitBcliHiSecureFlagCli(907), bitBoxCli(908), bitBcliBlockSwitchOverCli(909), bitBcliCtrlRecOptimizeCli(910), bitBcliLogParmsCli(911), bitPasswordAgeCli(912), bitLicenseLoadCli(913), bitportCliUnknownMacDiscAddAllowMacCli(914), bitBootpCliSetImageNameCli(915), bitdot3adAggTbl(916), bitdot3adAggPortTbl(917), bitrcLacpGlobalGrp(918), bitrcPortLacpTbl(919), bitrcPortVLacpTbl(920), bitdot1xPaeSystemGrp(921), bitdot1xAuthConfigTbl(922), bitdot1xPaePortTbl(923), bitdot3adrcPortLacpTbl(924), bitrcPortRemoteMirroringTbl(925), bitrcIpRsmltCli(926), bitsysCliV3NotifyFilterSetCli(927), bitsysCliV3NotifyProfileSetCli(928), bitsysCliSetSnmpServerCli(929), bitrcIpConfRsmltTbl(930), bitrcIpxRsmltOperTbl(931), bitcliLogCli(932), bitipmcCliSetDvmGlobTrapEnlCli(933), bitipmcCliSetDvmGlobLogEnlCli(934), bitDismanPingTraceroute(935), bitNaapCli(974), bitBcliAltLedEnableCli(975), bitBcliBackupCfgfileCli(976), bitrcBridgeFdbProtectTbl(977), bitrcSysDnsServer(978), bitBcli8616ReAutonegCli(979), bitBcliBootpImageNameSetCli(980), bitBcliMezzImageNameSetCli(981), bitBcliMacUpgradeCli(982), bitLoadConfigCli(983), bitBcliBootpImageNameInfo(984), bitospfCliSetRfc1583CompatibilityCli(985), bitShExecuteCli(986), bitsysCliSetHighThroughputModeCli(987), bitsysCliSetUdpChecksumCli(988), bitBcliMaintCommand(989), bitExtCpLimit(990), bitDumpCircuitcli(991), bitcppStatscli(992), bitfbuffDumpcli(993), bitmemShowcli(994), bitcheckStackcli(995), bitrcDumpSnmpcli(996), bitppeGetPortIsLinkUpcli(997), bitshowPpcli(998), bitdumpFacli(999), bitpimVirtualNbrTbl(1012), bitcliPasswordLockoutCli(1015), bitcliPasswordHistoryCli(1016), bitcliPasswordDefLockoutCli(1017), bitAutoRecoverSet(1019), bitAccessLevelEnDisCli(1020), bitrcTacacsGlobalGrp(1021), bitrcTacacsServerTbl(1022), bitPortCliSetSpoofDetectCli(1023), bitBcliMd5Cli(1024), bitBcliDumpfhCli(1025), bitBcliMezzCardBootEnableCli(1027), bitPasswordLenCli(1029), bitBcliCheckSrcRouteCli(1030), bitBcliLicensefileCli(1129), bitrcCfmGlobalsGrp(1053), bitrcIsisCircuitTbl(1055), bitisisCircTbl(1056), bitisisCircLevelTbl(1057), bitisisManAreaAddrTbl(1058), bitisisSummAddrTbl(1059), bitrcIsisGlobalGrp(1060), bitisisSysObjectGrp(1061), bitisisSysLevelTbl(1062), bitipCliSetIsisRedistApply(1063), bitisisCliClearStatsCli(1076), bitLbmCmdCli(1091), bitLtmCmdCli(1092), bitrcCfmMaintenanceDomainTbl(1125), bitrcCfmMaintenanceAssociationTbl(1126), bitrcCfmMaintenanceEndPointTbl(1127), bitBcliBootpSecImageNameSetCli(1148), bitrcMplsNotificationObjectsGrp(1149), bitmplsLsrObjectsGrp(1150), bitmplsTeObjectsGrp(1151), bitmplsTunnelHopTbl(1152), bitmplsTunnelTbl(1153), bitmplsTunnelResourceTbl(1154), bitrcMplsIpStaticFecTbl(1155), bitmplsClearLspLdpRsvpStats(1156), bitrcIpVpnRouteDistTbl(1157), bitrcIpVpnRouteTargetTbl(1158), bitrcVrfIpVpnTbl(1159), bitrcIpBgpPeerTblIpvpnLiteCap(1160), bitrcIpBgpPeerTblVpnv4Address(1161), bitmplspingcli(1162), bitrcPlsbGlobalGrp(1164), bitrcIsisPlsbTbl(1165), bitrcIsisCircuitPlsbTbl(1166), bitrcIsidEndptCvidClientMipTbl(1168), bitisisCliClearLsdbCli(1169), bitL2PingCmdCli(1175), bitL2TraceCmdCli(1176), bitL2TraceReplyCmdCli(1177), bitDebugL2vpnCmdCli(1178), bitDebugIsisCmdCli(1179), bitcardType(1536), bitrc2kCPU(1537), bitrc2k48x100BaseTX(1538), bitrc2k24x100BaseTX(1539), bitrc2k24x100BaseFX(1540), bitrc2k2xOC12(1541), bitrc2k8xATM(1542), bitrc2kRMON(1543), bitrc2k8x1000BaseSXBB(1544), bitrc2k8x1000BaseLXBB(1545), bitrc2k8x1000BaseSXRBB(1546), bitrc2k8x1000BaseLXRBB(1547), bitrc2k8x1000BaseXDBB(1548), bitrc2k8xOC3(1549), bitrc2kMg32x100BaseTX(1550), bitrc2kMg48x100BaseTX(1551), bitrc2kMg16x100BaseFX(1552), bitrc2kMg8x1000BaseIC(1553), bitrc2k8x1000BaseIC(1554), bitrc2kMg48x100BaseTC(1555), bitrc2k6xPOS(1556), bitrc2k16x1000BaseSXBB(1557), bitrc2k8x1000BaseT(1558), bitrc2k32x100BaseTX(1559), bitrc2k1x10GBaseLW(1560), bitrc2k16x1000BaseT(1561), bitrc2k1x10GBaseLR(1562), bitrc2kAlteonWSM(1563), bitrc2k48x100BaseTXM(1564), bitrc2k32x100BaseTXM(1565), bitrc2k8x1000BaseICM(1566), bitrc2k8x1000BaseSXBBM(1567), bitrc2k8x1000BaseTM(1568), bitrc2k8xATMM(1569), bitrc2k6xPOSM(1570), bitrc2kPP8300-CPU8x1000BaseSFP(1579), bitrc2kPP8300-24x1000BaseTX(1580), bitrc2kPP8300-48x100BaseTX(1581), bitrc2kPP8300-48x100BaseTXPOE(1582), bitrc2kAlteonLP(1583), bitrc2kAlteonASFM(1584), bitrc2k61AlteonSAM(1585), bitrc2k62AlteonSAM(1586), bitrcMplsGlobalGrp(1603), bitrcIpMplsInterfaceTbl(1604), bitrcVrfConfigTbl(1605), bitrcVrfIfConfigTbl(1606), bitrcIpv6InterfaceTbl(1607), bitrcIpv6AddrTbl(1608), bitrcIpv6PrefixTbl(1609), bitrcIpv6RouterAdvertTbl(1610), bitrcIpv6StaticRouteTbl(1611), bitrcIpv6NetToPhysicalTbl(1612), bitrcIpv6Scalars(1613), bitrcPrFilterAceIpv6SrcAddrTbl(1614), bitrcPrFilterAceIpv6DstAddrTbl(1615), bitrcPrFilterAceIpv6NextHdr(1616), bitrc2kCpuEthernetPortIpv6RouteTbl(1617), bitrcIpv6PimGlobalGrp(1618), bitrcIpv6PimTbl(1619), bitrcIpv6PimStaticRPTbl(1620), bitrcIpv6pimVirtualNbrTbl(1621), bitrcIpv6MulticastTimedPruneTbl(1622), bitrcIpv6MulticastSoftwareForwarding(1623), bitrcIpv6PimInterfaceTbl(1624), bitrcIpv6MltMcastDistributionGrp(1625), bitrcIpv6ResourceUsageGlobalGrp(1626), bitIpv6InterfaceTbl(1627), bitIpv6RouteTbl(1628), bitIpv6NetToMediaTbl(1629), bitIpv6MIBObjects(1630), bittunnelIfTbl(1631), bittunnelInetConfigTbl(1632), bitmldInterfaceTbl(1633), bitmldCacheTbl(1634), bitrcIpv6Ospfv3NbmaNbrTbl(1635), bitrcIpv6Ospfv3IfTbl(1636), bitrcIpv6Ospfv3VirtIf(1637), bitrcIpv6Ospfv3AreaAggregateTbl(1638), bitrcIpv6Ospfv3AreaTbl(1639), bitrcIpv6Ospfv3GeneralGrp(1640), bitrc2kPR48X1000BaseTX(1641), bitrc2kPR30X1000BaseSXBB(1642), bitrc2kPR3X10GBaseXZW(1643), bitrc2kPR3X10GBaseGbic(1644), bitrcIpfixConfGlobalGrp(1645), bitrcIpfixConfSlotTbl(1646), bitrcIpfixCollectorTbl(1647), bitrcIpfixConfPortTbl(1648), bitrcIpfixHashStatsTbl(1649), bitrcIpfixExporterStatsTbl(1650), bitTreeSnmp(1654), bitInfoCmdSnmp(1655), bitShowCmdSnmp(1656), bitsnmpLogSnmp(1657), bitrc2kPR48x1000BaseGBRS(1658), bitrc2kPR48x1000BaseGTRS(1659), bitrc2kPR12X10GBaseXLRS(1660), bitrc2kPR34xXGRS(1661), bitrcPrQosEgressQosToExpTbl(1662), bitrcPrQosIngressExpToQosTbl(1663), bitrcPomConfGlobalGrp(1664), bitrcIpv6DhcpForwardTbl(1672), bitrcIpv6ConfDhcpTbl(1673), bitrcIpv6VrrpOperTbl(1674), bitrcVrrpExtScalarsGrp(1675), bitrcVrrpTmpOperationsGrp(1676), bitrcIpMulticastSquareSmltGrp(1677), bitrcIpv6RsmltOperTbl(1678), bitrc2kCPURed(1679), bitrc2kPRE48x1000BaseGB(1680), bitrc2kPRE48x1000BaseGT(1681), bitrc2kPRE12X10GBaseXL(1682), bitrc2kPRE34xXG(1683), bitrcIpConfBfdTbl(1709), bitrcIpBfdGeneralGrp(1710), bitbasicrcIpBgpPeerTbl(1711), bitbasicbgpPeerTbl(1712), bitbasicrcIpBgpGeneralGrp(1713), bitbasicrcIpBgpAggregateTbl(1714), bitbasicrcIpBgpConfederationGrp(1715), bitbasicrcIpBgpRouteReflectorGrp(1716), bitbasicrcStatBgpGrp(1717), bitbasicrcStatBgpPeerTbl(1718), bitbasicrcIpBgpPeerGroupTbl(1719), bitbasicrcIpBgpNetworkTbl(1720), bitrcIpRedistributeTblIsis(1721), bitlastbitnum(2047)

rcLicenseBitMap		1.3.6.1.4.1.2272.1.56.2
License bit map. Bitmap number is defined in rcLicenseNumber
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(256)

rcSshGlobalHostIpAddr		1.3.6.1.4.1.2272.1.34.1.12
current remote ip addr
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcSslMipTable		1.3.6.1.4.1.2272.1.34.2
This table would display the MIP of the SSL blade according to the slot number.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcSslMipEntry

rcSslMipTableEntry		1.3.6.1.4.1.2272.1.34.2.1
This table get the MIP of the SSL blade on which the blade is in different cluster.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcSslMipEntry

rcSslMipSlot		1.3.6.1.4.1.2272.1.34.2.1.1
Used as an index to find out the MIP of SSL blade.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

rcSslMipMip		1.3.6.1.4.1.2272.1.34.2.1.2
Master IP of the SSL blade.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

rcLacpGlobal		1.3.6.1.4.1.2272.1.53.1
OBJECT IDENTIFIER

rcLacpGlobalEnable		1.3.6.1.4.1.2272.1.53.1.1
globally enable/disable LACP
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcLacpGlobalSystemPriority		1.3.6.1.4.1.2272.1.53.1.2
set system priority to all the LACP enabled aggregators and prots
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcLacpGlobalFastPeriodicTime		1.3.6.1.4.1.2272.1.53.1.3
The number of miliseconds between periodic transmissions using Short Timeouts. Set this value to all LACP enabled ports.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	200..20000

rcLacpGlobalSlowPeriodicTime		1.3.6.1.4.1.2272.1.53.1.4
The number of miliseconds between periodic transmissions using LONG Timeouts. Set this value to all LACP enabled ports.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	10000..30000

rcLacpGlobalTimeoutScale		1.3.6.1.4.1.2272.1.53.1.5
Scalar value used to calculate timeout time from periodic time. Set this value to all LACP enabled ports.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..10

rcLacpGlobalAggrWaitTime		1.3.6.1.4.1.2272.1.53.1.6
The number of mili seconds to delay aggregation to allow multiple links to aggregate simultaneously.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	200..2000

rcLacpGlobalVlacpEnable		1.3.6.1.4.1.2272.1.53.1.7
globally enable/disable Virtual LACP
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcLacpGlobalFastPeriodicTimeOper		1.3.6.1.4.1.2272.1.53.1.9
The operating value of global fast periodic timer.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	200..20000

rcLacpGlobalSlowPeriodicTimeOper		1.3.6.1.4.1.2272.1.53.1.10
The operating value of global show periodic time.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	10000..30000

rcLacpGlobalTimeoutScaleOper		1.3.6.1.4.1.2272.1.53.1.11
The operating value of global timeout scale.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..10

rcLacpGlobalAggrWaitTimeOper		1.3.6.1.4.1.2272.1.53.1.12
The operating value of global aggregate wait time.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	200..2000

rcLacpGlobalSmltSysId		1.3.6.1.4.1.2272.1.53.1.13
LACP system ID for SMLT
Status: current	Access: read-write
OBJECT-TYPE
	MacAddress

rcLacpGlobalVlacpHoldTime		1.3.6.1.4.1.2272.1.53.1.15
The number of seconds to hold down all vlacp enabled links
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..60

rcGlobalMacFilterTable		1.3.6.1.4.1.2272.1.60.1
A list of Global Mac filter entries.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcGlobalMacFilterEntry

rcGlobalMacFilterEntry		1.3.6.1.4.1.2272.1.60.1.1
this entry is used for global mac filtering.Any Mac address configured here will be discarded globally by the switch.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcGlobalMacFilterEntry

rcGlobalMacFilterAddress		1.3.6.1.4.1.2272.1.60.1.1.1
A MAC address which will be discarded globally by the switch
Status: current	Access: not-accessible
OBJECT-TYPE
	MacAddress

rcGlobalMacFilterRowStatus		1.3.6.1.4.1.2272.1.60.1.1.2
Used to create/delete entries in rcGlobalMacFilterTable.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcPowerRangerMib		1.3.6.1.4.1.2272.1.202.1
OBJECT IDENTIFIER

rcPowerRangerNotifications		1.3.6.1.4.1.2272.1.202.1.0
OBJECT IDENTIFIER

rcPowerRangerObjects		1.3.6.1.4.1.2272.1.202.1.1
OBJECT IDENTIFIER

rcPrQos		1.3.6.1.4.1.2272.1.202.1.1.1
OBJECT IDENTIFIER

rcPrFilter		1.3.6.1.4.1.2272.1.202.1.1.2
OBJECT IDENTIFIER

rcPrQosScalars		1.3.6.1.4.1.2272.1.202.1.1.1.1
OBJECT IDENTIFIER

rcPrQosPolicyNumPolicies		1.3.6.1.4.1.2272.1.202.1.1.1.1.1
A list of Global Policer (GPID) entries. The number of entries is given by rcPrQosPolicyNumPolicies.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..12288

rcPrQosTxQueueNumTemplates		1.3.6.1.4.1.2272.1.202.1.1.1.1.2
The number of egress queue templates currently defined in the switch.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..383

rcPrQosPolicyTable		1.3.6.1.4.1.2272.1.202.1.1.1.2
A list of GPID entries. The number of entries is given by rcPrQosPolicyNumPolicies.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrQosPolicyEntry

rcPrQosPolicyEntry		1.3.6.1.4.1.2272.1.202.1.1.1.2.1
Entry containing configuration information for a particular global policer.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrQosPolicyEntry

rcPrQosPolicyGpId		1.3.6.1.4.1.2272.1.202.1.1.1.2.1.1
A value that uniquely identifies Global Policer associated with this entry.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..16383

rcPrQosPolicyName		1.3.6.1.4.1.2272.1.202.1.1.1.2.1.2
An administratively-assigned name for this Global Policer.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..32)

rcPrQosPolicyPeakRate		1.3.6.1.4.1.2272.1.202.1.1.1.2.1.3
Global Policer Peak Rate in Kilobit/sec.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..10000000

rcPrQosPolicySvcRate		1.3.6.1.4.1.2272.1.202.1.1.1.2.1.4
Global Policer Service Rate in Kilobit/sec.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..10000000

rcPrQosPolicyLaneMembers		1.3.6.1.4.1.2272.1.202.1.1.1.2.1.5
The set of lanes that are members of this Global Policer. The string is 4 octets long, for a total of 32 bits. Each bit corresponds to a laneId. Each I/O slot has 4 laneIds. When a bit has the value one(1), the corresponding laneId is a member of the set. When a bit has the value zero(0), the corresponding laneId is not a member of the set. The encoding is such that the most significant bit of octet #1 corresponds to laneId 0, while the least significant bit of octet #4 corresponds to laneId 31.
Status: current	Access: read-write
OBJECT-TYPE
	LaneSet

rcPrQosPolicyRowStatus		1.3.6.1.4.1.2272.1.202.1.1.1.2.1.6
Create/delete operations for this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcPrQosLocalPolicyTable		1.3.6.1.4.1.2272.1.202.1.1.1.3
A list of local (aka physical) policer entries.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrQosLocalPolicyEntry

rcPrQosLocalPolicyEntry		1.3.6.1.4.1.2272.1.202.1.1.1.3.1
An entry containing configuration information for a particular local policer.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrQosLocalPolicyEntry

rcPrQosLocalPolicyGpId		1.3.6.1.4.1.2272.1.202.1.1.1.3.1.1
A value of Global Policer ID corresponding to this local policer.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..16383

rcPrQosLocalPolicyIndex		1.3.6.1.4.1.2272.1.202.1.1.1.3.1.2
A value that uniquely identifies the local Policer associated with this entry. Concatenation of tap.lane.lpid.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..16383

rcPrQosLocalPolicyPeakRate		1.3.6.1.4.1.2272.1.202.1.1.1.3.1.3
Local Policer Peak Rate in Kilobit/sec. Equals to that of corresponding Global Policer ID.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..10000000

rcPrQosLocalPolicySvcRate		1.3.6.1.4.1.2272.1.202.1.1.1.3.1.4
Local Policer Service Rate in Kilobit/sec. Equals to that of corresponding Global Policer ID.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..10000000

rcPrQosLocalPolicyTotalPkts		1.3.6.1.4.1.2272.1.202.1.1.1.3.1.5
Local Policer Total Packets Count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcPrQosLocalPolicyTotalBytes		1.3.6.1.4.1.2272.1.202.1.1.1.3.1.6
Local Policer Total Bytes Count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcPrQosLocalPolicyBytesOverPeak		1.3.6.1.4.1.2272.1.202.1.1.1.3.1.7
Local Policer Bytes over Peak Rate Count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcPrQosLocalPolicyBytesOverSvc		1.3.6.1.4.1.2272.1.202.1.1.1.3.1.8
Local Policer Bytes over Service Rate Count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcPrQosLocalPolicyTotalPktsDropped		1.3.6.1.4.1.2272.1.202.1.1.1.3.1.9
The count of Local Policer Total Packets dropped due to reasons other than policing, e.g. congestion.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcPrQosLocalPolicyLaneMember		1.3.6.1.4.1.2272.1.202.1.1.1.3.1.10
The lane that this Gpid has a local policing account on
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..4)

rcPrQosTxQueueTemplateTable		1.3.6.1.4.1.2272.1.202.1.1.1.4
A list of egress queue templates. The number of templates is given by rcPrQosTxQueueNumTemplates.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrQosTxQueueTemplateEntry

rcPrQosTxQueueTemplateEntry		1.3.6.1.4.1.2272.1.202.1.1.1.4.1
Entry containing configuration information for a particular egress queue template. Queue is a set of egress queues.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrQosTxQueueTemplateEntry

rcPrQosTxQueueTemplateId		1.3.6.1.4.1.2272.1.202.1.1.1.4.1.1
A value that uniquely identifies Egress Queue Template.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..386

rcPrQosTxQueueTemplateName		1.3.6.1.4.1.2272.1.202.1.1.1.4.1.2
An administratively-assigned name for this egress Queue Template.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..32)

rcPrQosTxQueueTemplateMaxQueues		1.3.6.1.4.1.2272.1.202.1.1.1.4.1.3
Maximum number of queues in this Template.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	eight(8), sixtyfour(64)

rcPrQosTxQueueTemplateBalancedQueues		1.3.6.1.4.1.2272.1.202.1.1.1.4.1.4
Total number of Balanced Queues in this Template.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..48

rcPrQosTxQueueTemplateHiPriQueues		1.3.6.1.4.1.2272.1.202.1.1.1.4.1.5
Total number of High Priority Queues in this Template.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..64

rcPrQosTxQueueTemplateLoPriQueues		1.3.6.1.4.1.2272.1.202.1.1.1.4.1.6
Total number of Low Priority Queues in this Template.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..8

rcPrQosTxQueueTemplateTotalQueues		1.3.6.1.4.1.2272.1.202.1.1.1.4.1.7
Total number of queues in this Template.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPrQosTxQueueTemplateBalancedQList		1.3.6.1.4.1.2272.1.202.1.1.1.4.1.8
List of Balanced Queues in this Template.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..200)

rcPrQosTxQueueTemplateHiPriQList		1.3.6.1.4.1.2272.1.202.1.1.1.4.1.9
List of High Priority Queues in this Template.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..200)

rcPrQosTxQueueTemplateLoPriQList		1.3.6.1.4.1.2272.1.202.1.1.1.4.1.10
List of Low Priority Queues in this Template.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..200)

rcPrQosTxQueueTemplateTotalQLists		1.3.6.1.4.1.2272.1.202.1.1.1.4.1.11
List of Total Physical Queues in this Template.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..600)

rcPrQosTxQueueTemplateMinRateTotal		1.3.6.1.4.1.2272.1.202.1.1.1.4.1.12
Sum of minimum rate guarantees for this template.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..100

rcPrQosTxQueueTemplateMaxRateHiPri		1.3.6.1.4.1.2272.1.202.1.1.1.4.1.13
Sum of maximum rate guarantees for high priority queues of this template.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..100

rcPrQosTxQueueTemplatePortMembers		1.3.6.1.4.1.2272.1.202.1.1.1.4.1.14
Port members of this template.
Status: current	Access: read-write
OBJECT-TYPE
	PortSet

rcPrQosTxQueueTemplateFlags		1.3.6.1.4.1.2272.1.202.1.1.1.4.1.15
Bitset indicated template state.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	created(1), committed(2), modified(3)

rcPrQosTxQueueTemplateApply		1.3.6.1.4.1.2272.1.202.1.1.1.4.1.16
When apply is issued by the administrator, the Egress Queue Set attributes are committed.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcPrQosTxQueueTemplateRowStatus		1.3.6.1.4.1.2272.1.202.1.1.1.4.1.17
Create/delete operations for this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcPrQosTxQueueTable		1.3.6.1.4.1.2272.1.202.1.1.1.5
A list of elementary Egress queue entries.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrQosTxQueueEntry

rcPrQosTxQueueEntry		1.3.6.1.4.1.2272.1.202.1.1.1.5.1
Entry containing configuration information for a particular elementary egress queue.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrQosTxQueueEntry

rcPrQosTxQueueTid		1.3.6.1.4.1.2272.1.202.1.1.1.5.1.1
Template ID of the template this queue belongs to.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..386

rcPrQosTxQueueQid		1.3.6.1.4.1.2272.1.202.1.1.1.5.1.2
Queue Offset from the base queue for this port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..63

rcPrQosTxQueueName		1.3.6.1.4.1.2272.1.202.1.1.1.5.1.3
An NNSC name for this egress queue. Allowed only for 8 NNSC queues.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..32)

rcPrQosTxQueueStyle		1.3.6.1.4.1.2272.1.202.1.1.1.5.1.4
Egress queue style.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	hipri(1), balanced(2), lopri(3)

rcPrQosTxQueueWeight		1.3.6.1.4.1.2272.1.202.1.1.1.5.1.5
Egress queue weight. Applicable for balanced queues and lo-pri queues only.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPrQosTxQueueMaxRate		1.3.6.1.4.1.2272.1.202.1.1.1.5.1.6
Egress queue maximum rate, Kbs
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcPrQosTxQueueMinRate		1.3.6.1.4.1.2272.1.202.1.1.1.5.1.7
Egress queue minimun rate guarantee, Kbs. Applicable for balanced queues and lo-pri queues only.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcPrQosTxQueueBquantum		1.3.6.1.4.1.2272.1.202.1.1.1.5.1.8
Bandwidth allocation unit. Applicable for balanced queues and lo-pri queues only.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPrQosTxQueueMaxLength		1.3.6.1.4.1.2272.1.202.1.1.1.5.1.9
Maximum queue length.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcPrQosTxQueueWredCurveSet		1.3.6.1.4.1.2272.1.202.1.1.1.5.1.10
Random Early Detection Number.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	tailDrop(1), lowDrop(2), mediumDrop(3), highDrop(4)

rcPrQosTxQueueRowStatus		1.3.6.1.4.1.2272.1.202.1.1.1.5.1.11
Create/delete operations for this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcPrQosTxQueueStatsTable		1.3.6.1.4.1.2272.1.202.1.1.1.6
A list of elementary Egress queue stats entries.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrQosTxQueueStatsEntry

rcPrQosTxQueueStatsEntry		1.3.6.1.4.1.2272.1.202.1.1.1.6.1
Entry containing statistics information for a particular elementary egress queue.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrQosTxQueueStatsEntry

rcPrQosTxQueueStatsPort		1.3.6.1.4.1.2272.1.202.1.1.1.6.1.1
Port index of the stats table.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcPrQosTxQueueStatsQid		1.3.6.1.4.1.2272.1.202.1.1.1.6.1.2
Queue Offset from the base queue for this port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..63

rcPrQosTxQueueStatsTotalPages		1.3.6.1.4.1.2272.1.202.1.1.1.6.1.3
Total pages offered to the queue.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcPrQosTxQueueStatsDroppedPages		1.3.6.1.4.1.2272.1.202.1.1.1.6.1.4
Total pages dropped by the queue.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcPrQosTxQueueStatsUtilization		1.3.6.1.4.1.2272.1.202.1.1.1.6.1.5
Utilization percentage of the queue.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..100

rcPrQosIngressExpToQosTable		1.3.6.1.4.1.2272.1.202.1.1.1.7
This table is used to specify the Mpls EXP to QOS (Exp bit->QOS) mapping on packet ingress.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrQosIngressExpToQosEntry

rcPrQosIngressExpToQosEntry		1.3.6.1.4.1.2272.1.202.1.1.1.7.1
Entry containing information of Exp bit->Qos mapping
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrQosIngressExpToQosEntry

rcPrQosIngressExpToQosIndex		1.3.6.1.4.1.2272.1.202.1.1.1.7.1.1
Used to uniquely identify a row in this table.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..8

rcPrQosIngressExpToQosMplsExp		1.3.6.1.4.1.2272.1.202.1.1.1.7.1.2
The Mpls Exp bit level.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..7

rcPrQosIngressExpToQosLevel		1.3.6.1.4.1.2272.1.202.1.1.1.7.1.3
qos level
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..7

rcPrQosIngressExpToQosRowStatus		1.3.6.1.4.1.2272.1.202.1.1.1.7.1.4
Create/delete operations for this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcPrQosEgressQosToExpTable		1.3.6.1.4.1.2272.1.202.1.1.1.8
This table is used to specify the QOS to Mpls EXP bit field (QOS->Exp bit) mapping on packet egress.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrQosEgressQosToExpEntry

rcPrQosEgressQosToExpEntry		1.3.6.1.4.1.2272.1.202.1.1.1.8.1
Entry containing infomation of Qos->Exp bit mapping
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrQosEgressQosToExpEntry

rcPrQosEgressQosToExpIndex		1.3.6.1.4.1.2272.1.202.1.1.1.8.1.1
Used to uniquely identify a row in this table.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..8

rcPrQosEgressQosToExpQosLevel		1.3.6.1.4.1.2272.1.202.1.1.1.8.1.2
qos level
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..7

rcPrQosEgressQosToExpMplsExp		1.3.6.1.4.1.2272.1.202.1.1.1.8.1.3
The Mpls EXP bit level.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..7

rcPrQosEgressQosToExpRowStatus		1.3.6.1.4.1.2272.1.202.1.1.1.8.1.4
Create/delete operations for this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcPrFilterScalars		1.3.6.1.4.1.2272.1.202.1.1.2.1
OBJECT IDENTIFIER

rcPrFilterActTableSize		1.3.6.1.4.1.2272.1.202.1.1.2.1.1
Used to indicate the number of Act entries in the rcPrFilterActTable. Default table size is 0 until the administrator configures any Act entries.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4096

rcPrFilterAclTableSize		1.3.6.1.4.1.2272.1.202.1.1.2.1.2
Used to indicate the number of Acl entries in the rcPrFilterAclTable. Default table size is 0 until the administrator configures any Acl entries.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4096

rcPrFilterAceTableSize		1.3.6.1.4.1.2272.1.202.1.1.2.1.3
Used to indicate the number of Ace entries in the rcPrFilterAceTable. Default table size is 0 until the administrator configures any Ace entries. The maximum size is # of Acls multiplied by # of Aces.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..10000

rcPrFilterAct		1.3.6.1.4.1.2272.1.202.1.1.2.2
OBJECT IDENTIFIER

rcPrFilterActTable		1.3.6.1.4.1.2272.1.202.1.1.2.2.1
A table of Acts to store information of each Act entry. This table is indexed by the Act Id.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrFilterActEntry

rcPrFilterActEntry		1.3.6.1.4.1.2272.1.202.1.1.2.2.1.1
One Act Entry holding Act information.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrFilterActEntry

rcPrFilterActId		1.3.6.1.4.1.2272.1.202.1.1.2.2.1.1.1
A table of Acts to store information of each Act. This table is indexed by the Act Id.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4096

rcPrFilterActName		1.3.6.1.4.1.2272.1.202.1.1.2.2.1.1.2
A descriptive name chosen by the administrator for the Act Entry.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..32)

rcPrFilterActArpAttrs		1.3.6.1.4.1.2272.1.202.1.1.2.2.1.1.3
Value is one or multiple (logical 'OR' of the following): none(0), operation(1) none: No Arp Attrs are selected or to clear other choices. operation: Only valid option for Arp attributes.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..1

rcPrFilterActEthernetAttrs		1.3.6.1.4.1.2272.1.202.1.1.2.2.1.1.4
Value is one or multiple of the following: none(0), srcMac(1), dstMac(2), etherType(4), port(8), vlan(16), vlanTagPrio(32) none: If selected then unselect all other selections.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..63

rcPrFilterActIpAttrs		1.3.6.1.4.1.2272.1.202.1.1.2.2.1.1.5
Value is one or multiple of the following: none(0), srcIp(1), dstIp(2), ipFragFlag(4), ipOptions(8), ipProtoType(16), dscp(32) none: If selected then unselect all other selections.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..63

rcPrFilterActProtocolAttrs		1.3.6.1.4.1.2272.1.202.1.1.2.2.1.1.6
Value is one or multiple of the following: none(0), tcpSrcPort(1), udpSrcPort(2), tcpDstPort(4), udpDstPort(8), tcpFlags(16), icmpMsgType(32) none: If selected then unselect all other selections.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..63

rcPrFilterActApply		1.3.6.1.4.1.2272.1.202.1.1.2.2.1.1.7
When apply is issued by the administrator, the ACT attributes cannot be modified.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcPrFilterActRowStatus		1.3.6.1.4.1.2272.1.202.1.1.2.2.1.1.8
Create/delete operations for this entry. The entry cannot be modified or deleted while there are Acls configured with this Act entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcPrFilterActIpv6Attrs		1.3.6.1.4.1.2272.1.202.1.1.2.2.1.1.9
Value is one or multiple of the following: none(0), srcIpv6(1), dstIpv6(4), nextHdr(16), none: If selected then unselect all other selections.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..63

rcPrFilterActPatternTable		1.3.6.1.4.1.2272.1.202.1.1.2.2.2
A table of user-defined parameters of Acls to store information of each Acl. This table is indexed by the Act Id and PatternIndex.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrFilterActPatternEntry

rcPrFilterActPatternEntry		1.3.6.1.4.1.2272.1.202.1.1.2.2.2.1
Entry containing Configuration information for a particular Act.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrFilterActPatternEntry

rcPrFilterActPatternActId		1.3.6.1.4.1.2272.1.202.1.1.2.2.2.1.1
An index to the ActPatternEntry, a unique identifier for Act entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4096

rcPrFilterActPatternIndex		1.3.6.1.4.1.2272.1.202.1.1.2.2.2.1.2
Indexes each user defined field pattern in an Acl entry. In this release only 3 patterns are allowed per ACT but we can have multiple patterns per ACL.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..16

rcPrFilterActPatternName		1.3.6.1.4.1.2272.1.202.1.1.2.2.2.1.3
A descriptive name chosen by the administrator for the Acl Pattern Entry.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..32)

rcPrFilterActPatternBase		1.3.6.1.4.1.2272.1.202.1.1.2.2.2.1.4
User defined fields from headers to be used in the Aces of the Acl.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), etherBegin(1), macDstBegin(2), macSrcBegin(3), ethTypeLenBegin(4), arpBegin(5), ipHdrBegin(6), ipOptionsBegin(7), ipPayloadBegin(8), ipTosBegin(9), ipProtoBegin(10), ipSrcBegin(11), ipDstBegin(12), tcpBegin(13), tcpSrcportBegin(14), tcpDstportBegin(15), tcpFlagsEnd(16), udpBegin(17), udpSrcportBegin(18), udpDstportBegin(19), etherEnd(20), ipHdrEnd(21), icmpMsgBegin(22), tcpEnd(23), udpEnd(24), ipv6HdrBegin(25)

rcPrFilterActPatternOffset		1.3.6.1.4.1.2272.1.202.1.1.2.2.2.1.5
Set Offset in bits to the beginning offset of the user defined field with selected header option as base.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..76800

rcPrFilterActPatternLength		1.3.6.1.4.1.2272.1.202.1.1.2.2.2.1.6
The number of bits to extract beginning from the offset is set in rcPrFilterActPatternLength. Only 1-56 are valid.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..56

rcPrFilterActPatternRowStatus		1.3.6.1.4.1.2272.1.202.1.1.2.2.2.1.7
Create/delete operations for this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcPrFilterAcl		1.3.6.1.4.1.2272.1.202.1.1.2.3
OBJECT IDENTIFIER

rcPrFilterAclTable		1.3.6.1.4.1.2272.1.202.1.1.2.3.1
A table of Acls to store information of each Acl. This table is indexed by the Acl Id.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrFilterAclEntry

rcPrFilterAclEntry		1.3.6.1.4.1.2272.1.202.1.1.2.3.1.1
Entry containing Configuration information for a particular Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrFilterAclEntry

rcPrFilterAclId		1.3.6.1.4.1.2272.1.202.1.1.2.3.1.1.1
A unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4096

rcPrFilterAclActId		1.3.6.1.4.1.2272.1.202.1.1.2.3.1.1.2
A unique identifier for Act entry in the range of Table Size.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..4096

rcPrFilterAclName		1.3.6.1.4.1.2272.1.202.1.1.2.3.1.1.3
A descriptive name chosen by the administrator for the Acl Entry.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..32)

rcPrFilterAclType		1.3.6.1.4.1.2272.1.202.1.1.2.3.1.1.4
An Acl can be vlan-based or port-based. An Ace has a capability to match packets classified as 'ingress' and 'egress'. An ingress packet is assigned a value 'in' and an egress packet is assigned a value 'out'.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	inVlan(1), outVlan(2), inPort(3), outPort(4)

rcPrFilterAclAceListSize		1.3.6.1.4.1.2272.1.202.1.1.2.3.1.1.5
Indicates the number of Aces in a particular Acl.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..1000

rcPrFilterAclDefaultAction		1.3.6.1.4.1.2272.1.202.1.1.2.3.1.1.6
Indicates action to be taken when none of the Aces in the Acl match.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	deny(1), permit(2)

rcPrFilterAclGlobalAction		1.3.6.1.4.1.2272.1.202.1.1.2.3.1.1.7
Indicates action is applied to all Aces that match in an Acl.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), mirror(2), count(3), mirror-count(4), ipfix(5), mirror-ipfix(6), count-ipfix(7), mirror-count-ipfix(8)

rcPrFilterAclState		1.3.6.1.4.1.2272.1.202.1.1.2.3.1.1.8
Enables/Disables the state of all Aces in the Acl
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcPrFilterAclVlanList		1.3.6.1.4.1.2272.1.202.1.1.2.3.1.1.9
An array used to indicate all the VLANs to be associated with this Acl Entry. At present, only 4k Vlans are supported.
Status: current	Access: read-write
OBJECT-TYPE
	IdList	Size(0..4096)

rcPrFilterAclPortList		1.3.6.1.4.1.2272.1.202.1.1.2.3.1.1.10
Indicates the ports to be added to this Acl Entry.
Status: current	Access: read-write
OBJECT-TYPE
	PortSet

rcPrFilterAclRowStatus		1.3.6.1.4.1.2272.1.202.1.1.2.3.1.1.11
Create/delete operations for the entry. Deleting a non-empty Acl results in deletion of member Aces and then the Acl.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcPrFilterAclNumVlanIds		1.3.6.1.4.1.2272.1.202.1.1.2.3.1.1.12
Used to Indicate the number of VLAN ID's that are stored in the rcPrFilterAclVlanList.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4096

rcPrFilterAclPktType		1.3.6.1.4.1.2272.1.202.1.1.2.3.1.1.13
Indicates the packet type that thsi ACL is applicable to.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ipv4(1), ipv6(2)

rcPrFilterAclStatsTable		1.3.6.1.4.1.2272.1.202.1.1.2.3.2
A table of Acls Statistics entries to store the Default Acl statistics for each Acl. This table is indexed by the Acl Id.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrFilterAclStatsEntry

rcPrFilterAclStatsEntry		1.3.6.1.4.1.2272.1.202.1.1.2.3.2.1
Entry containing default statistics information for a particular Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrFilterAclStatsEntry

rcPrFilterAclStatsAclId		1.3.6.1.4.1.2272.1.202.1.1.2.3.2.1.1
A unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4096

rcPrFilterAclStatsMatchDefaultCounterPkts		1.3.6.1.4.1.2272.1.202.1.1.2.3.2.1.2
Packet count of traffic not matching any of the Ace rules or hit the Default Action that have the count bit turned on in Acl Global Action.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcPrFilterAclStatsMatchDefaultOctets		1.3.6.1.4.1.2272.1.202.1.1.2.3.2.1.3
Byte count of traffic not matching any of the Ace rules or hit the Default Action that have the count bit turned on in Acl Global Action.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcPrFilterAclStatsClear		1.3.6.1.4.1.2272.1.202.1.1.2.3.2.1.4
Clear default statistics for ACL Filters.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcPrFilterAce		1.3.6.1.4.1.2272.1.202.1.1.2.4
OBJECT IDENTIFIER

rcPrFilterAceTable		1.3.6.1.4.1.2272.1.202.1.1.2.4.1
A table of Aces to store information of each Ace in context of its parent Acl. This is indexed by AclId and AceId.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrFilterAceEntry

rcPrFilterAceEntry		1.3.6.1.4.1.2272.1.202.1.1.2.4.1.1
One Ace entry holding Ace information. Ace is a member of one Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrFilterAceEntry

rcPrFilterAceAclId		1.3.6.1.4.1.2272.1.202.1.1.2.4.1.1.1
An index to the AceEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4096

rcPrFilterAceId		1.3.6.1.4.1.2272.1.202.1.1.2.4.1.1.2
AceId uniquely identifies one Ace entry.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1000

rcPrFilterAceName		1.3.6.1.4.1.2272.1.202.1.1.2.4.1.1.3
A descriptive name chosen by the administrator. System automatically assigns a name if the user has not assigned one.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..32)

rcPrFilterAceMode		1.3.6.1.4.1.2272.1.202.1.1.2.4.1.1.4
Operating Mode associated with the Ace is effective on the packets matching this Ace.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), deny(1), permit(2)

rcPrFilterAceRemarkDscp		1.3.6.1.4.1.2272.1.202.1.1.2.4.1.1.5
The 6-bit DSCP field from the ToS byte in Ipv4 header encodes the PHB information per DiffServ standards (Refer to DiffServ RFCs 2474). Set the Dscp to PHB (like EF) or PHB-class(like AF1 which includes AF11, AF12,AF13) to mark specific diffserv class traffic. Set the field value to desired integer dscp code for rcPrFilterAceRemarkDscp field to mark non-standard traffic classes and local use PHBs.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	phbcs0(0), phbcs1(8), phbaf11(10), phbaf12(12), phbaf13(14), phbcs2(16), phbaf21(18), phbaf22(20), phbaf23(22), phbcs3(24), phbaf31(26), phbaf32(28), phbaf33(30), phbcs4(32), phbaf41(34), phbaf42(36), phbaf43(38), phbcs5(40), phbef(46), phbcs6(48), phbcs7(56), disable(256)

rcPrFilterAceRemarkDot1Priority		1.3.6.1.4.1.2272.1.202.1.1.2.4.1.1.6
Dot1 Priority as described by Layer 2 standards, 802.1Q, 802.1P.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	zero(0), one(1), two(2), three(3), four(4), five(5), six(6), seven(7), disable(8)

rcPrFilterAceRedirectNextHop		1.3.6.1.4.1.2272.1.202.1.1.2.4.1.1.7
Redirect matching IP traffic to the next hop.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcPrFilterAceRedirectUnreach		1.3.6.1.4.1.2272.1.202.1.1.2.4.1.1.8
Set the desired behavior for redirected traffic in case the specified next-hop is not reachable.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	deny(1), permit(2)

rcPrFilterAcePolice		1.3.6.1.4.1.2272.1.202.1.1.2.4.1.1.9
Policing profile Identifier. Set the desired policing profile identifier. Set the value to 0 when policing is not desired.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..16383

rcPrFilterAceAdminState		1.3.6.1.4.1.2272.1.202.1.1.2.4.1.1.10
Value indicating whether the Ace is enabled. An Ace can only be modified if it is disabled.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcPrFilterAceOperState		1.3.6.1.4.1.2272.1.202.1.1.2.4.1.1.11
The current operational state of the Ace.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2)

rcPrFilterAceEgressQueue		1.3.6.1.4.1.2272.1.202.1.1.2.4.1.1.12
Indicates the Egress Queue for 10/100 card. If only 1 value is specified then this value is applied to Queue1g and Queue10g as well. If 2 values are specified then the first value is applied to 10/100 card and the second value is applied to 1gig and 10gig cards. If all three values are specified, then all three values are applied respectively to the appropriate Egress Queue. If value is greater than 8, it will not be applied to the 10/100 card as it only has 8 queues. However, the value will be applied to the 1gig and 10gig card types.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..64

rcPrFilterAceEgressQueue1g		1.3.6.1.4.1.2272.1.202.1.1.2.4.1.1.13
Indicates the Egress Queue for 1gig card.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..64

rcPrFilterAceEgressQueue10g		1.3.6.1.4.1.2272.1.202.1.1.2.4.1.1.14
Indicates the Egress Queue for 10gig card.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..64

rcPrFilterAceEgressQueueNNSC		1.3.6.1.4.1.2272.1.202.1.1.2.4.1.1.15
Ace Egress Queue NNSC.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	platinum(0), gold(1), silver(2), bronze(3), standard(4), custom(5), premium(6), critical(7), disable(8)

rcPrFilterAceFlags		1.3.6.1.4.1.2272.1.202.1.1.2.4.1.1.16
Bitmask for the flags: none(0): Default value for the flags. stopOnMatch(1): set desired behavior for flag whether to stop or continue in case an Ace matching the packet is found. When this Ace is hit, match on other Aces with a lower priority is not attempted. count(2): set desired behavior for flag i.e. to enable/disable counting in case a packet matching the ace is found. copyToPrimaryCp(4): set to enable/disable copying of matching packets to primary CP. copyToSecondaryCp(8): set to enable/disable copying of matching packets to secondary CP. mirror(16): set to enable/disable mirroring the matching packets to an interface. System can mirror one port or mirror to 1 port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..31

rcPrFilterAceStopOnMatch		1.3.6.1.4.1.2272.1.202.1.1.2.4.1.1.17
Value indicating whether stop-on-match option on the Ace is enabled.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcPrFilterAceMltIndex		1.3.6.1.4.1.2272.1.202.1.1.2.4.1.1.18
If this action is specified, it will basically override the mlt-index picked by the mlt algorithm, when a packet is being sent out on MLT ports.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..8

rcPrFilterAceRowStatus		1.3.6.1.4.1.2272.1.202.1.1.2.4.1.1.19
Create/delete operations for this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcPrFilterAceIpfixState		1.3.6.1.4.1.2272.1.202.1.1.2.4.1.1.20
Value indicating whether ipfix option on the Ace is enabled.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcPrFilterAceRedirectNextHopIpv6		1.3.6.1.4.1.2272.1.202.1.1.2.4.1.1.21
Redirect matching IPv6 traffic to the next hop.
Status: current	Access: read-write
OBJECT-TYPE
	Ipv6Address

rcPrFilterAceDstPortList		1.3.6.1.4.1.2272.1.202.1.1.2.4.1.1.22
Destination Port List for mirroring the packets.
Status: current	Access: read-create
OBJECT-TYPE
	PortSet

rcPrFilterAceDstVlanId		1.3.6.1.4.1.2272.1.202.1.1.2.4.1.1.23
Destination Vlan to mirror the packets.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..4094

rcPrFilterAceDstMltId		1.3.6.1.4.1.2272.1.202.1.1.2.4.1.1.24
Destination Mlt to mirror the packets.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..256

rcPrFilterAceEthSrcAddrTable		1.3.6.1.4.1.2272.1.202.1.1.2.4.2
A table of Aces to store Ethernet Source MAC Address Header information of each Ace in context of its parent Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrFilterAceEthSrcAddrEntry

rcPrFilterAceEthSrcAddrEntry		1.3.6.1.4.1.2272.1.202.1.1.2.4.2.1
One Ace entry holding Ace Ethernet Source MAC Address information. An Ace is a member of one Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrFilterAceEthSrcAddrEntry

rcPrFilterAceEthSrcAddrAclId		1.3.6.1.4.1.2272.1.202.1.1.2.4.2.1.1
An index to the AceEthernetEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4096

rcPrFilterAceEthSrcAddrAceId		1.3.6.1.4.1.2272.1.202.1.1.2.4.2.1.2
An index to the AceEthernetEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1000

rcPrFilterAceEthSrcAddrList		1.3.6.1.4.1.2272.1.202.1.1.2.4.2.1.3
The list of ethernet source address to match.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..1500)

rcPrFilterAceEthSrcAddrListCount		1.3.6.1.4.1.2272.1.202.1.1.2.4.2.1.4
Count to store the number of discrete ranges entered for the ethernet src address.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..100

rcPrFilterAceEthSrcAddrOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.2.1.5
Operators for Ace Ethernet Source MAC Address.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	eq(1), ne(2), le(3), ge(4)

rcPrFilterAceEthSrcAddrRowStatus		1.3.6.1.4.1.2272.1.202.1.1.2.4.2.1.6
Create/delete operations for this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcPrFilterAceEthDstAddrTable		1.3.6.1.4.1.2272.1.202.1.1.2.4.3
A table of Aces to store Ethernet Destination MAC Address Header information of each Ace in context of its parent Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrFilterAceEthDstAddrEntry

rcPrFilterAceEthDstAddrEntry		1.3.6.1.4.1.2272.1.202.1.1.2.4.3.1
One Ace entry holding Ace Ethernet Destination MAC Address information. An Ace is a member of one Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrFilterAceEthDstAddrEntry

rcPrFilterAceEthDstAddrAclId		1.3.6.1.4.1.2272.1.202.1.1.2.4.3.1.1
An index to the AceEthDstAddrEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4096

rcPrFilterAceEthDstAddrAceId		1.3.6.1.4.1.2272.1.202.1.1.2.4.3.1.2
An index to the AceEthDstAddrEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1000

rcPrFilterAceEthDstAddrList		1.3.6.1.4.1.2272.1.202.1.1.2.4.3.1.3
List of ethernet destination address to match.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..1500)

rcPrFilterAceEthDstAddrListCount		1.3.6.1.4.1.2272.1.202.1.1.2.4.3.1.4
Count to store the number of discrete ranges entered for the ethernet dst address.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..100

rcPrFilterAceEthDstAddrOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.3.1.5
Operators for Ace Ethernet Destination MAC Address.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	eq(1), ne(2), le(3), ge(4)

rcPrFilterAceEthDstAddrRowStatus		1.3.6.1.4.1.2272.1.202.1.1.2.4.3.1.6
Create/delete operations for this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcPrFilterAceEthEtherTable		1.3.6.1.4.1.2272.1.202.1.1.2.4.4
A table of Aces to store Ethernet Ether Header information of each Ace in context of its parent Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrFilterAceEthEtherEntry

rcPrFilterAceEthEtherEntry		1.3.6.1.4.1.2272.1.202.1.1.2.4.4.1
One Ace entry holding Ace Ethernet Ether information. An Ace is a member of one Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrFilterAceEthEtherEntry

rcPrFilterAceEthEtherAclId		1.3.6.1.4.1.2272.1.202.1.1.2.4.4.1.1
An index to the AceEthEtherEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4096

rcPrFilterAceEthEtherAceId		1.3.6.1.4.1.2272.1.202.1.1.2.4.4.1.2
An index to the AceEthEtherEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1000

rcPrFilterAceEthEtherTypeList		1.3.6.1.4.1.2272.1.202.1.1.2.4.4.1.3
EtherType value from ethernet header. For example ARP uses 0x0806, IP uses 0x0800. The platform support determines the behavior for 802.1Q/p tagged packets. The EtherType for 802.1Q tagged frames is 0x8100. Valid range for the 16-bit Ether-type is 0..65535 and the attribute supports lists/ranges of values. Invalid ether-type value 65536 is interpreted as field is not desired in match criteria.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..1500)

rcPrFilterAceEthEtherTypeListCount		1.3.6.1.4.1.2272.1.202.1.1.2.4.4.1.4
Count to store the number of discrete ranges entered for the ethernet types.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..100

rcPrFilterAceEthEtherTypeOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.4.1.5
Ethernet Type Operators.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	eq(1), ne(2)

rcPrFilterAceEthEtherRowStatus		1.3.6.1.4.1.2272.1.202.1.1.2.4.4.1.6
Create/delete operations for this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcPrFilterAceEthVlanTagPrioTable		1.3.6.1.4.1.2272.1.202.1.1.2.4.5
A table of Aces to store Ethernet Vlan Tag Priority Header information of each Ace in context of its parent Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrFilterAceEthVlanTagPrioEntry

rcPrFilterAceEthVlanTagPrioEntry		1.3.6.1.4.1.2272.1.202.1.1.2.4.5.1
One Ace entry holding Ace Ethernet Vlan Tag Priority information. An Ace is a member of one Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrFilterAceEthVlanTagPrioEntry

rcPrFilterAceEthVlanTagPrioAclId		1.3.6.1.4.1.2272.1.202.1.1.2.4.5.1.1
An index to the AceEthVlanTagPrioEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4096

rcPrFilterAceEthVlanTagPrioAceId		1.3.6.1.4.1.2272.1.202.1.1.2.4.5.1.2
An index to the AceEthVlanTagPrioEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1000

rcPrFilterAceEthVlanTagPrioVlanTagPrio		1.3.6.1.4.1.2272.1.202.1.1.2.4.5.1.3
Priority bits (3-bit field) from the 802.1Q/p tag.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	zero(0), one(1), two(2), three(3), four(4), five(5), six(6), seven(7)

rcPrFilterAceEthVlanTagPrioOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.5.1.4
Operators for Ace Ethernet Vlan Tag Priority.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	eq(1), ne(2)

rcPrFilterAceEthVlanTagPrioRowStatus		1.3.6.1.4.1.2272.1.202.1.1.2.4.5.1.5
Create/delete operations for this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcPrFilterAceEthPortTable		1.3.6.1.4.1.2272.1.202.1.1.2.4.6
A table of Aces to store Ethernet Port Header information of each Ace in context of its parent Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrFilterAceEthPortEntry

rcPrFilterAceEthPortEntry		1.3.6.1.4.1.2272.1.202.1.1.2.4.6.1
One Ace entry holding Ace Ethernet Port information. An Ace is a member of one Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrFilterAceEthPortEntry

rcPrFilterAceEthPortAclId		1.3.6.1.4.1.2272.1.202.1.1.2.4.6.1.1
An index to the AceEthPortEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4096

rcPrFilterAceEthPortAceId		1.3.6.1.4.1.2272.1.202.1.1.2.4.6.1.2
An index to the AceEthPortEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1000

rcPrFilterAceEthPortPort		1.3.6.1.4.1.2272.1.202.1.1.2.4.6.1.3
Port Number or Port List to match on.
Status: current	Access: read-write
OBJECT-TYPE
	PortSet

rcPrFilterAceEthPortOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.6.1.4
Operator for Ace Ethernet Port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	eq(1), ne(2)

rcPrFilterAceEthPortRowStatus		1.3.6.1.4.1.2272.1.202.1.1.2.4.6.1.5
Create/delete operations for this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcPrFilterAceEthVlanIdTable		1.3.6.1.4.1.2272.1.202.1.1.2.4.7
A table of Aces to store Ethernet Vlan Id Header information of each Ace in context of its parent Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrFilterAceEthVlanIdEntry

rcPrFilterAceEthVlanIdEntry		1.3.6.1.4.1.2272.1.202.1.1.2.4.7.1
One Ace entry holding Ace Ethernet Vlan Id information. An Ace is a member of one Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrFilterAceEthVlanIdEntry

rcPrFilterAceEthVlanIdAclId		1.3.6.1.4.1.2272.1.202.1.1.2.4.7.1.1
An index to the AceEthVlanIdEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4096

rcPrFilterAceEthVlanIdAceId		1.3.6.1.4.1.2272.1.202.1.1.2.4.7.1.2
An index to the AceEthVlanIdEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1000

rcPrFilterAceEthVlanIdVlanIdList		1.3.6.1.4.1.2272.1.202.1.1.2.4.7.1.3
Vlan Id to match on.
Status: current	Access: read-write
OBJECT-TYPE
	IdList	Size(4096)

rcPrFilterAceEthVlanIdOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.7.1.4
Operator for Ace Ethernet VlanId.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	eq(1), ne(2)

rcPrFilterAceEthVlanIdRowStatus		1.3.6.1.4.1.2272.1.202.1.1.2.4.7.1.5
Create/delete operations for this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcPrFilterAceArpTable		1.3.6.1.4.1.2272.1.202.1.1.2.4.8
A table of Aces to store Arp Header information of each Ace in context of its parent Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrFilterAceArpEntry

rcPrFilterAceArpEntry		1.3.6.1.4.1.2272.1.202.1.1.2.4.8.1
One Ace entry holding Ace Arp Header information. Ace is a member of one Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrFilterAceArpEntry

rcPrFilterAceArpAclId		1.3.6.1.4.1.2272.1.202.1.1.2.4.8.1.1
An index to the AceArpEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4096

rcPrFilterAceArpAceId		1.3.6.1.4.1.2272.1.202.1.1.2.4.8.1.2
An index to the AceArpEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1000

rcPrFilterAceArpType		1.3.6.1.4.1.2272.1.202.1.1.2.4.8.1.3
Ace Arp Operation.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	operation(1)

rcPrFilterAceArpOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.8.1.4
Operator for Ace Arp Operation.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	eq(1)

rcPrFilterAceArpValue		1.3.6.1.4.1.2272.1.202.1.1.2.4.8.1.5
Ace Arp can be a request or a response.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	arpRequest(1), arpResponse(2)

rcPrFilterAceArpRowStatus		1.3.6.1.4.1.2272.1.202.1.1.2.4.8.1.6
Create/delete operations for this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcPrFilterAceIpSrcAddrTable		1.3.6.1.4.1.2272.1.202.1.1.2.4.9
A table of Aces to store IP Source Address Header information of each Ace in context of its parent Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrFilterAceIpSrcAddrEntry

rcPrFilterAceIpSrcAddrEntry		1.3.6.1.4.1.2272.1.202.1.1.2.4.9.1
One Ace entry holding Ace IP Source Address Header information. An Ace is a member of one Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrFilterAceIpSrcAddrEntry

rcPrFilterAceIpSrcAddrAclId		1.3.6.1.4.1.2272.1.202.1.1.2.4.9.1.1
An index to the AceIpSrcAddrEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4096

rcPrFilterAceIpSrcAddrAceId		1.3.6.1.4.1.2272.1.202.1.1.2.4.9.1.2
An index to the AceIpSrcAddrEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1000

rcPrFilterAceIpSrcAddrList		1.3.6.1.4.1.2272.1.202.1.1.2.4.9.1.3
The list of ip source address to match from IP header.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..1500)

rcPrFilterAceIpSrcAddrListCount		1.3.6.1.4.1.2272.1.202.1.1.2.4.9.1.4
Count to store the number of discrete ranges entered for the ip src address.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..100

rcPrFilterAceIpSrcAddrOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.9.1.5
Operators for Ace Ip Source Address.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	eq(1), ne(2), le(3), ge(4), prefix(8)

rcPrFilterAceIpSrcAddrRowStatus		1.3.6.1.4.1.2272.1.202.1.1.2.4.9.1.6
Create/delete operations for this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcPrFilterAceIpDstAddrTable		1.3.6.1.4.1.2272.1.202.1.1.2.4.10
A table of Aces to store IP Destination Address Header information of each Ace in context of its parent Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrFilterAceIpDstAddrEntry

rcPrFilterAceIpDstAddrEntry		1.3.6.1.4.1.2272.1.202.1.1.2.4.10.1
One Ace entry holding Ace IP Destination Address Header information. An Ace is a member of one Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrFilterAceIpDstAddrEntry

rcPrFilterAceIpDstAddrAclId		1.3.6.1.4.1.2272.1.202.1.1.2.4.10.1.1
An index to the AceIpDstAddrEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4096

rcPrFilterAceIpDstAddrAceId		1.3.6.1.4.1.2272.1.202.1.1.2.4.10.1.2
An index to the AceIpDstAddrEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1000

rcPrFilterAceIpDstAddrList		1.3.6.1.4.1.2272.1.202.1.1.2.4.10.1.3
The list of ip dst address to match from IP header.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..1500)

rcPrFilterAceIpDstAddrListCount		1.3.6.1.4.1.2272.1.202.1.1.2.4.10.1.4
Count to store the number of discrete ranges entered for the IP Destination Address.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..100

rcPrFilterAceIpDstAddrOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.10.1.5
Operators for Ace IP Destination Address.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	eq(1), ne(2), le(3), ge(4), prefix(8)

rcPrFilterAceIpDstAddrRowStatus		1.3.6.1.4.1.2272.1.202.1.1.2.4.10.1.6
Create/delete operations for this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcPrFilterAceIpDscpTable		1.3.6.1.4.1.2272.1.202.1.1.2.4.11
A table of Aces to store IP Dscp Header information of each Ace in context of its parent Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrFilterAceIpDscpEntry

rcPrFilterAceIpDscpEntry		1.3.6.1.4.1.2272.1.202.1.1.2.4.11.1
One Ace entry holding Ace IP Dscp Header information. An Ace is a member of one Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrFilterAceIpDscpEntry

rcPrFilterAceIpDscpAclId		1.3.6.1.4.1.2272.1.202.1.1.2.4.11.1.1
An index to the AceIpDscpEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4096

rcPrFilterAceIpDscpAceId		1.3.6.1.4.1.2272.1.202.1.1.2.4.11.1.2
An index to the AceIpDscpEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1000

rcPrFilterAceIpDscpList		1.3.6.1.4.1.2272.1.202.1.1.2.4.11.1.3
The 6-bit DSCP field from the ToS byte in Ipv4 header encodes the PHB information per DiffServ standards (Refer to DiffServ RFCs 2474). Set the Dscp to PHB (like EF) or PHB-class(like AF1 which includes AF11, AF12,AF13) to match specific diffserv class traffic. Set the field value to desired dscp code for 'rcPrFilterAceIpDscp' field to match non-standard traffic classes and local use PHBs.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..1500)

rcPrFilterAceIpDscpListCount		1.3.6.1.4.1.2272.1.202.1.1.2.4.11.1.4
Count to store the number of discrete ranges entered for the dscp values.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..100

rcPrFilterAceIpDscpOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.11.1.5
Operators for Ace Ip Dscp.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	eq(1), ne(2)

rcPrFilterAceIpDscpRowStatus		1.3.6.1.4.1.2272.1.202.1.1.2.4.11.1.6
Create/delete operations for this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcPrFilterAceIpProtoTable		1.3.6.1.4.1.2272.1.202.1.1.2.4.12
A table of Aces to store IP Proto Header information of each Ace in context of its parent Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrFilterAceIpProtoEntry

rcPrFilterAceIpProtoEntry		1.3.6.1.4.1.2272.1.202.1.1.2.4.12.1
One Ace entry holding Ace IP Proto Header information. An Ace is a member of one Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrFilterAceIpProtoEntry

rcPrFilterAceIpProtoAclId		1.3.6.1.4.1.2272.1.202.1.1.2.4.12.1.1
An index to the AceIpProtoEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4096

rcPrFilterAceIpProtoAceId		1.3.6.1.4.1.2272.1.202.1.1.2.4.12.1.2
An index to the AceIpProtoEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1000

rcPrFilterAceIpProtoList		1.3.6.1.4.1.2272.1.202.1.1.2.4.12.1.3
Ip protocol Type from the ip header to be matched. Valid Ip protocol range is 0..255. Few of the Protocol Types are enumerated above. In case the desired protocol number is not available in the enumerated list set protocol to desired integer value
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..1500)

rcPrFilterAceIpProtoListCount		1.3.6.1.4.1.2272.1.202.1.1.2.4.12.1.4
Count to store the number of discrete ranges entered for the ethernet protocol ids.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..100

rcPrFilterAceIpProtoOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.12.1.5
Operators for Ace Ip Protocols.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	eq(1), ne(2)

rcPrFilterAceIpProtoRowStatus		1.3.6.1.4.1.2272.1.202.1.1.2.4.12.1.6
Create/delete operations for this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcPrFilterAceIpOptionsTable		1.3.6.1.4.1.2272.1.202.1.1.2.4.13
A table of Aces to store IP Options Header information of each Ace in context of its parent Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrFilterAceIpOptionsEntry

rcPrFilterAceIpOptionsEntry		1.3.6.1.4.1.2272.1.202.1.1.2.4.13.1
One Ace entry holding Ace IP Options Header information. An Ace is a member of one Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrFilterAceIpOptionsEntry

rcPrFilterAceIpOptionsAclId		1.3.6.1.4.1.2272.1.202.1.1.2.4.13.1.1
An index to the AceIpOptionsEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4096

rcPrFilterAceIpOptionsAceId		1.3.6.1.4.1.2272.1.202.1.1.2.4.13.1.2
An index to the AceIpOptionsEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1000

rcPrFilterAceIpOptionsOptions		1.3.6.1.4.1.2272.1.202.1.1.2.4.13.1.3
Ip options to be matched from the IP Header.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noOperation(1), recordRoute(7), experimentalMeasurement(10), mtuProbe(11), mtuReply(12), encode(15), timestamp(68), traceroute(82), baseSecurity(130), looseSourceRoute(131), extendedSecurity(133), commercialSecurity(134), streamID(136), strictSourceRouting(137), experimentalAccessControl(142), imiTrafficDescriptor(144), extendedIP(145), addressExtension(147), routeAlert(148), selectiveDirectedBroadcast(149), nsapAddresses(150), dynamicPacketState(151), upstreamMulticastPacket(152), experimentalFlowControl(205)

rcPrFilterAceIpOptionsOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.13.1.4
Logical Operator - only 'any' is valid at present.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	any(5)

rcPrFilterAceIpOptionsRowStatus		1.3.6.1.4.1.2272.1.202.1.1.2.4.13.1.5
Create/delete operations for this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcPrFilterAceIpFragTable		1.3.6.1.4.1.2272.1.202.1.1.2.4.14
A table of Aces to store IP Fragmentation Header information of each Ace in context of its parent Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrFilterAceIpFragEntry

rcPrFilterAceIpFragEntry		1.3.6.1.4.1.2272.1.202.1.1.2.4.14.1
One Ace entry holding Ace IP Fragmentation Header information. An Ace is a member of one Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrFilterAceIpFragEntry

rcPrFilterAceIpFragAclId		1.3.6.1.4.1.2272.1.202.1.1.2.4.14.1.1
An index to the AceIpFragEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4096

rcPrFilterAceIpFragAceId		1.3.6.1.4.1.2272.1.202.1.1.2.4.14.1.2
An index to the AceIpFragEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1000

rcPrFilterAceIpFragFragmentation		1.3.6.1.4.1.2272.1.202.1.1.2.4.14.1.3
Ip Fragmentation bits to be matched from the IP Header.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noFragment(0), anyFragment(1), moreFragment(2), unused3(3), lastFragment(4), unused5(5), unused6(6), unused7(7)

rcPrFilterAceIpFragOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.14.1.4
Operator for Ip fragmentation.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	eq(1)

rcPrFilterAceIpFragRowStatus		1.3.6.1.4.1.2272.1.202.1.1.2.4.14.1.5
Create/delete operations for this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcPrFilterAceProtoTcpSrcPortTable		1.3.6.1.4.1.2272.1.202.1.1.2.4.15
A table of Aces to store TCP Source Port information of each Ace in context of its parent Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrFilterAceProtoTcpSrcPortEntry

rcPrFilterAceProtoTcpSrcPortEntry		1.3.6.1.4.1.2272.1.202.1.1.2.4.15.1
One entry holding Ace Protocol TCP Source Port information. An Ace is a member of one Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrFilterAceProtoTcpSrcPortEntry

rcPrFilterAceProtoTcpSrcPortAclId		1.3.6.1.4.1.2272.1.202.1.1.2.4.15.1.1
An index to the AceProtoTcpSrcPortEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4096

rcPrFilterAceProtoTcpSrcPortAceId		1.3.6.1.4.1.2272.1.202.1.1.2.4.15.1.2
An index to the AceProtoTcpSrcPortEntry, a unique identifier for Ace entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1000

rcPrFilterAceProtoTcpSrcPortPort		1.3.6.1.4.1.2272.1.202.1.1.2.4.15.1.3
Port Number or Port List to match on.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..1500)

rcPrFilterAceProtoTcpSrcPortCount		1.3.6.1.4.1.2272.1.202.1.1.2.4.15.1.4
Count to store the number of discrete ranges entered for the TCP source port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..100

rcPrFilterAceProtoTcpSrcPortOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.15.1.5
Operator for Ace Protocol TcpSrcPort.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	eq(1), ne(2), le(3), ge(4)

rcPrFilterAceProtoTcpSrcPortRowStatus		1.3.6.1.4.1.2272.1.202.1.1.2.4.15.1.6
Create/delete operations for this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcPrFilterAceProtoUdpSrcPortTable		1.3.6.1.4.1.2272.1.202.1.1.2.4.16
A table of Aces to store UDP Source Port information of each Ace in context of its parent Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrFilterAceProtoUdpSrcPortEntry

rcPrFilterAceProtoUdpSrcPortEntry		1.3.6.1.4.1.2272.1.202.1.1.2.4.16.1
One entry holding Ace Protocol UDP Source Port information. An Ace is a member of one Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrFilterAceProtoUdpSrcPortEntry

rcPrFilterAceProtoUdpSrcPortAclId		1.3.6.1.4.1.2272.1.202.1.1.2.4.16.1.1
An index to the AceProtoUdpSrcPortEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4096

rcPrFilterAceProtoUdpSrcPortAceId		1.3.6.1.4.1.2272.1.202.1.1.2.4.16.1.2
An index to the AceProtoUdpSrcPortEntry, a unique identifier for Ace entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1000

rcPrFilterAceProtoUdpSrcPortPort		1.3.6.1.4.1.2272.1.202.1.1.2.4.16.1.3
Port Number or Port List to match on.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..1500)

rcPrFilterAceProtoUdpSrcPortCount		1.3.6.1.4.1.2272.1.202.1.1.2.4.16.1.4
Count to store the number of discrete ranges entered for the UDP source port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..100

rcPrFilterAceProtoUdpSrcPortOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.16.1.5
Operator for Ace Protocol UdpSrcPort.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	eq(1), ne(2), le(3), ge(4)

rcPrFilterAceProtoUdpSrcPortRowStatus		1.3.6.1.4.1.2272.1.202.1.1.2.4.16.1.6
Create/delete operations for this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcPrFilterAceProtoTcpDstPortTable		1.3.6.1.4.1.2272.1.202.1.1.2.4.17
A table of Aces to store TCP Dest Port information of each Ace in context of its parent Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrFilterAceProtoTcpDstPortEntry

rcPrFilterAceProtoTcpDstPortEntry		1.3.6.1.4.1.2272.1.202.1.1.2.4.17.1
One entry holding Ace Protocol TCP Dest Port information. An Ace is a member of one Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrFilterAceProtoTcpDstPortEntry

rcPrFilterAceProtoTcpDstPortAclId		1.3.6.1.4.1.2272.1.202.1.1.2.4.17.1.1
An index to the AceProtoTcpDstPortEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4096

rcPrFilterAceProtoTcpDstPortAceId		1.3.6.1.4.1.2272.1.202.1.1.2.4.17.1.2
An index to the AceProtoTcpDstPortEntry, a unique identifier for Ace entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1000

rcPrFilterAceProtoTcpDstPortPort		1.3.6.1.4.1.2272.1.202.1.1.2.4.17.1.3
Port Number or Port List to match on.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..1500)

rcPrFilterAceProtoTcpDstPortCount		1.3.6.1.4.1.2272.1.202.1.1.2.4.17.1.4
Count to store the number of discrete ranges entered for the TCP dest port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..100

rcPrFilterAceProtoTcpDstPortOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.17.1.5
Operator for Ace Protocol TcpDstPort.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	eq(1), ne(2), le(3), ge(4)

rcPrFilterAceProtoTcpDstPortRowStatus		1.3.6.1.4.1.2272.1.202.1.1.2.4.17.1.6
Create/delete operations for this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcPrFilterAceProtoUdpDstPortTable		1.3.6.1.4.1.2272.1.202.1.1.2.4.18
A table of Aces to store UDP Dest Port information of each Ace in context of its parent Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrFilterAceProtoUdpDstPortEntry

rcPrFilterAceProtoUdpDstPortEntry		1.3.6.1.4.1.2272.1.202.1.1.2.4.18.1
One entry holding Ace Protocol UDP Dest Port information. An Ace is a member of one Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrFilterAceProtoUdpDstPortEntry

rcPrFilterAceProtoUdpDstPortAclId		1.3.6.1.4.1.2272.1.202.1.1.2.4.18.1.1
An index to the AceProtoUdpDstPortEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4096

rcPrFilterAceProtoUdpDstPortAceId		1.3.6.1.4.1.2272.1.202.1.1.2.4.18.1.2
An index to the AceProtoUdpDstPortEntry, a unique identifier for Ace entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1000

rcPrFilterAceProtoUdpDstPortPort		1.3.6.1.4.1.2272.1.202.1.1.2.4.18.1.3
Port Number or Port List to match on.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..1500)

rcPrFilterAceProtoUdpDstPortCount		1.3.6.1.4.1.2272.1.202.1.1.2.4.18.1.4
Count to store the number of discrete ranges entered for the UDP dest port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..100

rcPrFilterAceProtoUdpDstPortOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.18.1.5
Operator for Ace Protocol UdpDstPort.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	eq(1), ne(2), le(3), ge(4)

rcPrFilterAceProtoUdpDstPortRowStatus		1.3.6.1.4.1.2272.1.202.1.1.2.4.18.1.6
Create/delete operations for this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcPrFilterAceProtoIcmpMsgTypeTable		1.3.6.1.4.1.2272.1.202.1.1.2.4.19
A table of Aces to store ICMP message type information of each Ace in context of its parent Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrFilterAceProtoIcmpMsgTypeEntry

rcPrFilterAceProtoIcmpMsgTypeEntry		1.3.6.1.4.1.2272.1.202.1.1.2.4.19.1
One entry holding Ace ICMP message type information. An Ace is a member of one Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrFilterAceProtoIcmpMsgTypeEntry

rcPrFilterAceProtoIcmpMsgTypeAclId		1.3.6.1.4.1.2272.1.202.1.1.2.4.19.1.1
An index to the AceProtoIcmpMsgTypeEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4096

rcPrFilterAceProtoIcmpMsgTypeAceId		1.3.6.1.4.1.2272.1.202.1.1.2.4.19.1.2
An index to the AceProtoIcmpMsgTypeEntry, a unique identifier for Ace entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1000

rcPrFilterAceProtoIcmpMsgTypeList		1.3.6.1.4.1.2272.1.202.1.1.2.4.19.1.3
One or a list of Icmp messages to be matched. Need to provide strings, number of protocol header types (pre-defined values plus user-defined headers). Valid range is 0 to 255 (reserved).
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..1500)

rcPrFilterAceProtoIcmpMsgTypeCount		1.3.6.1.4.1.2272.1.202.1.1.2.4.19.1.4
Count to store the number of discrete ranges entered for the ICMP message types.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..100

rcPrFilterAceProtoIcmpMsgTypeOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.19.1.5
Operator for Ace Protocol IcmpMsgTypes.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	eq(1), ne(2)

rcPrFilterAceProtoIcmpMsgTypeRowStatus		1.3.6.1.4.1.2272.1.202.1.1.2.4.19.1.6
Create/delete operations for this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcPrFilterAceProtoTcpFlagsTable		1.3.6.1.4.1.2272.1.202.1.1.2.4.20
A table of Aces to store TCP Flags information of each Ace in context of its parent Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrFilterAceProtoTcpFlagsEntry

rcPrFilterAceProtoTcpFlagsEntry		1.3.6.1.4.1.2272.1.202.1.1.2.4.20.1
One entry holding Ace Protocol TCP flags information. An Ace is a member of one Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrFilterAceProtoTcpFlagsEntry

rcPrFilterAceProtoTcpFlagsAclId		1.3.6.1.4.1.2272.1.202.1.1.2.4.20.1.1
An index to the rcPrFilterAceProtoTcpFlagsEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4096

rcPrFilterAceProtoTcpFlagsAceId		1.3.6.1.4.1.2272.1.202.1.1.2.4.20.1.2
An index to the rcPrFilterAceProtoTcpFlagsEntry, a unique identifier for Ace entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1000

rcPrFilterAceProtoTcpFlagsList		1.3.6.1.4.1.2272.1.202.1.1.2.4.20.1.3
One or a list of Tcp flags to be matched. Need to provide strings, number of protocol header types (pre-defined values plus user-defined headers). Valid range is 0 to 63
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..1500)

rcPrFilterAceProtoTcpFlagsCount		1.3.6.1.4.1.2272.1.202.1.1.2.4.20.1.4
Count to store the number of discrete ranges entered for the TCP flags.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..100

rcPrFilterAceProtoTcpFlagsOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.20.1.5
Operator for Ace Protocol TcpFlags.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	matchAny(6), matchAll(7)

rcPrFilterAceProtoTcpFlagsRowStatus		1.3.6.1.4.1.2272.1.202.1.1.2.4.20.1.6
Create/delete operations for this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcPrFilterAcePattern1Table		1.3.6.1.4.1.2272.1.202.1.1.2.4.21
A table of pattern fields for Aces to manage the settings for each user defined field.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrFilterAcePattern1Entry

rcPrFilterAcePattern1Entry		1.3.6.1.4.1.2272.1.202.1.1.2.4.21.1
One Ace entry holding Ace User Defined Pattern information. Ace is a member of one Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrFilterAcePattern1Entry

rcPrFilterAcePattern1AclId		1.3.6.1.4.1.2272.1.202.1.1.2.4.21.1.1
An index to the AcePatternEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4096

rcPrFilterAcePattern1AceId		1.3.6.1.4.1.2272.1.202.1.1.2.4.21.1.2
An index to the AcePatternEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1000

rcPrFilterAcePattern1Name		1.3.6.1.4.1.2272.1.202.1.1.2.4.21.1.3
A descriptive name chosen by the administrator for the Ace Pattern Entry.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..32)

rcPrFilterAcePattern1Value		1.3.6.1.4.1.2272.1.202.1.1.2.4.21.1.4
Set the pattern value as numeric string. The numeric value of each byte is encoded in one octet of the string. Unused bytes are left at the trailing end of string. The number of bytes to extract from this string is set in rcPrFilterActPatternLength.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..1500)

rcPrFilterAcePattern1Oper		1.3.6.1.4.1.2272.1.202.1.1.2.4.21.1.5
Operators for Ace Pattern.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	eq(1), le(3), ge(4)

rcPrFilterAcePattern1RowStatus		1.3.6.1.4.1.2272.1.202.1.1.2.4.21.1.6
Create/delete operations for this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcPrFilterAcePattern2Table		1.3.6.1.4.1.2272.1.202.1.1.2.4.22
A table of pattern fields for Aces to manage the settings for each user defined field.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrFilterAcePattern2Entry

rcPrFilterAcePattern2Entry		1.3.6.1.4.1.2272.1.202.1.1.2.4.22.1
One Ace entry holding Ace User Defined Pattern information. Ace is a member of one Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrFilterAcePattern2Entry

rcPrFilterAcePattern2AclId		1.3.6.1.4.1.2272.1.202.1.1.2.4.22.1.1
An index to the AcePatternEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4096

rcPrFilterAcePattern2AceId		1.3.6.1.4.1.2272.1.202.1.1.2.4.22.1.2
An index to the AcePatternEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1000

rcPrFilterAcePattern2Name		1.3.6.1.4.1.2272.1.202.1.1.2.4.22.1.3
A descriptive name chosen by the administrator for the Ace Pattern Entry.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..32)

rcPrFilterAcePattern2Value		1.3.6.1.4.1.2272.1.202.1.1.2.4.22.1.4
Set the pattern value as numeric string. The numeric value of each byte is encoded in one octet of the string. Unused bytes are left at the trailing end of string. The number of bytes to extract from this string is set in rcPrFilterActPatternLength.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..1500)

rcPrFilterAcePattern2Oper		1.3.6.1.4.1.2272.1.202.1.1.2.4.22.1.5
Operators for Ace Pattern.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	eq(1), le(3), ge(4)

rcPrFilterAcePattern2RowStatus		1.3.6.1.4.1.2272.1.202.1.1.2.4.22.1.6
Create/delete operations for this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcPrFilterAcePattern3Table		1.3.6.1.4.1.2272.1.202.1.1.2.4.23
A table of pattern fields for Aces to manage the settings for each user defined field.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrFilterAcePattern3Entry

rcPrFilterAcePattern3Entry		1.3.6.1.4.1.2272.1.202.1.1.2.4.23.1
One Ace entry holding Ace User Defined Pattern information. Ace is a member of one Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrFilterAcePattern3Entry

rcPrFilterAcePattern3AclId		1.3.6.1.4.1.2272.1.202.1.1.2.4.23.1.1
An index to the AcePatternEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4096

rcPrFilterAcePattern3AceId		1.3.6.1.4.1.2272.1.202.1.1.2.4.23.1.2
An index to the AcePatternEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1000

rcPrFilterAcePattern3Name		1.3.6.1.4.1.2272.1.202.1.1.2.4.23.1.3
A descriptive name chosen by the administrator for the Ace Pattern Entry.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..32)

rcPrFilterAcePattern3Value		1.3.6.1.4.1.2272.1.202.1.1.2.4.23.1.4
Set the pattern value as numeric string. The numeric value of each byte is encoded in one octet of the string. Unused bytes are left at the trailing end of string. The number of bytes to extract from this string is set in rcPrFilterActPatternLength.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..1500)

rcPrFilterAcePattern3Oper		1.3.6.1.4.1.2272.1.202.1.1.2.4.23.1.5
Operators for Ace Pattern.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	eq(1), le(3), ge(4)

rcPrFilterAcePattern3RowStatus		1.3.6.1.4.1.2272.1.202.1.1.2.4.23.1.6
Create/delete operations for this entry.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcPrFilterAceStatsTable		1.3.6.1.4.1.2272.1.202.1.1.2.4.24
A table of ACE Statistics Entries to store per-ACE-per-Port Statistics
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrFilterAceStatsEntry

rcPrFilterAceStatsEntry		1.3.6.1.4.1.2272.1.202.1.1.2.4.24.1
Ace Statistics entry holding per-ACE-per-port Statistics
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrFilterAceStatsEntry

rcPrFilterAceStatsAclId		1.3.6.1.4.1.2272.1.202.1.1.2.4.24.1.1
An index to the AceStatsEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4096

rcPrFilterAceStatsAceId		1.3.6.1.4.1.2272.1.202.1.1.2.4.24.1.2
An index to the AceStatsEntry, a unique identifier for ACE entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1000

rcPrFilterAceStatsPortId		1.3.6.1.4.1.2272.1.202.1.1.2.4.24.1.3
An index to the AceStatsEntry, a unique identifier of the portId
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..703

rcPrFilterAceStatsMatchCountPkts		1.3.6.1.4.1.2272.1.202.1.1.2.4.24.1.4
Count of packets that match this particular Ace on this particular port.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcPrFilterAceStatsMatchCountOctets		1.3.6.1.4.1.2272.1.202.1.1.2.4.24.1.5
Byte count of traffic that match this particular Ace on this particular port
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcPrFilterAceStatsClear		1.3.6.1.4.1.2272.1.202.1.1.2.4.24.1.6
Clear Per-ACE-Per-Port statistics.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcPrFilterAceEthShowTable		1.3.6.1.4.1.2272.1.202.1.1.2.4.25
A table of Aces to store Ethernet Header information of each Ace in context of its parent Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrFilterAceEthShowEntry

rcPrFilterAceEthShowEntry		1.3.6.1.4.1.2272.1.202.1.1.2.4.25.1
One Ace entry holding Ace Ethernet information. Ace is a member of one Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrFilterAceEthShowEntry

rcPrFilterAceEthShowAclId		1.3.6.1.4.1.2272.1.202.1.1.2.4.25.1.1
An index to the AceEthernetEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4096

rcPrFilterAceEthShowAceId		1.3.6.1.4.1.2272.1.202.1.1.2.4.25.1.2
An index to the AceEthernetEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1000

rcPrFilterAceEthShowSrcAddrList		1.3.6.1.4.1.2272.1.202.1.1.2.4.25.1.3
The list of ethernet source address to match.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..1500)

rcPrFilterAceEthShowSrcAddrOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.25.1.4
Operators for Ace Ethernet Source MAC Address.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	eq(1), ne(2), le(3), ge(4), any(255)

rcPrFilterAceEthShowDstAddrList		1.3.6.1.4.1.2272.1.202.1.1.2.4.25.1.5
List of ethernet destination address to match.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..1500)

rcPrFilterAceEthShowDstAddrOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.25.1.6
Operators for Ace Ethernet Destination MAC Address.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	eq(1), ne(2), le(3), ge(4), any(255)

rcPrFilterAceEthShowEtherTypeList		1.3.6.1.4.1.2272.1.202.1.1.2.4.25.1.7
EtherType value from ethernet header. For example ARP uses 0x0806, IP uses 0x0800. The platform support determines the behavior for 802.1Q/p tagged packets. The EtherType for 802.1Q tagged frames is 0x8100. Valid range for the 16-bit Ether-type is 0..65535 and the attribute supports lists/ranges of values. Invalid ether-type value 65536 is interpreted as field is not desired in match criteria.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..1500)

rcPrFilterAceEthShowEtherTypeOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.25.1.8
Ethernet Type Operators.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	eq(1), ne(2), any(255)

rcPrFilterAceEthShowVlanTagPrio		1.3.6.1.4.1.2272.1.202.1.1.2.4.25.1.9
Priority bits (3-bit field) from the 802.1Q/p tag.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	zero(0), one(1), two(2), three(3), four(4), five(5), six(6), seven(7)

rcPrFilterAceEthShowVlanTagPrioOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.25.1.10
Operators for Ace Ethernet Vlan Tag Priority.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	eq(1), ne(2), any(255)

rcPrFilterAceEthShowPort		1.3.6.1.4.1.2272.1.202.1.1.2.4.25.1.11
Port Number or Port List to match on.
Status: current	Access: read-only
OBJECT-TYPE
	PortSet

rcPrFilterAceEthShowPortOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.25.1.12
Operator for Ace Ethernet Port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	eq(1), ne(2), any(255)

rcPrFilterAceEthShowVlanIdList		1.3.6.1.4.1.2272.1.202.1.1.2.4.25.1.13
Vlan Id to match on.
Status: current	Access: read-only
OBJECT-TYPE
	IdList	Size(0..4096)

rcPrFilterAceEthShowVlanIdOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.25.1.14
Operator for Ace Ethernet VlanId.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	eq(1), ne(2), any(255)

rcPrFilterAceIpShowTable		1.3.6.1.4.1.2272.1.202.1.1.2.4.26
A table of Aces to store IP Header information of each Ace in context of its parent Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrFilterAceIpShowEntry

rcPrFilterAceIpShowEntry		1.3.6.1.4.1.2272.1.202.1.1.2.4.26.1
One Ace entry holding Ace IP information. Ace is a member of one Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrFilterAceIpShowEntry

rcPrFilterAceIpShowAclId		1.3.6.1.4.1.2272.1.202.1.1.2.4.26.1.1
An index to the AceIpShowEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4096

rcPrFilterAceIpShowAceId		1.3.6.1.4.1.2272.1.202.1.1.2.4.26.1.2
An index to the AceIpShowEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1000

rcPrFilterAceIpShowSrcAddrList		1.3.6.1.4.1.2272.1.202.1.1.2.4.26.1.3
The list of ip source address to match from IP header.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..1500)

rcPrFilterAceIpShowSrcAddrOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.26.1.4
Operators for Ace Ip Source Address.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	eq(1), ne(2), le(3), ge(4), prefix(8), any(255)

rcPrFilterAceIpShowDstAddrList		1.3.6.1.4.1.2272.1.202.1.1.2.4.26.1.5
The list of ip dst address to match from IP header.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..1500)

rcPrFilterAceIpShowDstAddrOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.26.1.6
Operators for Ace Ip Destination Address.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	eq(1), ne(2), le(3), ge(4), prefix(8), any(255)

rcPrFilterAceIpShowDscpList		1.3.6.1.4.1.2272.1.202.1.1.2.4.26.1.7
The 6-bit DSCP field from the ToS byte in Ipv4 header encodes the PHB information per DiffServ standards (Refer to DiffServ RFCs 2474). Set the Dscp to PHB (like EF) or PHB-class(like AF1 which includes AF11, AF12,AF13) to match specific diffserv class traffic. Set the field value to desired dscp code for 'rcPrFilterAceIpDscp' field to match non-standard traffic classes and local use PHBs.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..1500)

rcPrFilterAceIpShowDscpOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.26.1.8
Operators for Ace Ip Dscp.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	eq(1), ne(2), any(255)

rcPrFilterAceIpShowProtoList		1.3.6.1.4.1.2272.1.202.1.1.2.4.26.1.9
Ip protocol Type from the ip header to be matched. Valid Ip protocol range is 0..255. Few of the Protocol Types are enumerated above. In case the desired protocol number is not available in the enumerated list set protocol to desired integer value
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..1500)

rcPrFilterAceIpShowProtoOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.26.1.10
Operators for Ace Ip Protocols.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	eq(1), ne(2), any(255)

rcPrFilterAceIpShowOptions		1.3.6.1.4.1.2272.1.202.1.1.2.4.26.1.11
Ip options to be matched from the IP Header.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	noOperation(1), recordRoute(7), experimentalMeasurement(10), mtuProbe(11), mtuReply(12), encode(15), timestamp(68), traceroute(82), baseSecurity(130), looseSourceRoute(131), extendedSecurity(133), commercialSecurity(134), streamID(136), strictSourceRouting(137), experimentalAccessControl(142), imiTrafficDescriptor(144), extendedIP(145), addressExtension(147), routeAlert(148), selectiveDirectedBroadcast(149), nsapAddresses(150), dynamicPacketState(151), upstreamMulticastPacket(152), experimentalFlowControl(205)

rcPrFilterAceIpShowOptionsOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.26.1.12
Logical Operator - only 'any' is valid at present.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	any(5)

rcPrFilterAceIpShowFragmentation		1.3.6.1.4.1.2272.1.202.1.1.2.4.26.1.13
Ip Fragmentation bits to be matched from the IP Header.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	noFragment(0), anyFragment(1), moreFragment(2), unused3(3), lastFragment(4), unused5(5), unused6(6), unused7(7)

rcPrFilterAceIpShowFragOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.26.1.14
Operator for Ip fragmentation.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	eq(1), any(255)

rcPrFilterAceProtoShowTable		1.3.6.1.4.1.2272.1.202.1.1.2.4.27
A table of Aces to store Protocol Header information of each Ace in context of its parent Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrFilterAceProtoShowEntry

rcPrFilterAceProtoShowEntry		1.3.6.1.4.1.2272.1.202.1.1.2.4.27.1
One Ace entry holding Ace Ethernet information. Ace is a member of one Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrFilterAceProtoShowEntry

rcPrFilterAceProtoShowAclId		1.3.6.1.4.1.2272.1.202.1.1.2.4.27.1.1
An index to the AceProtoShowEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4096

rcPrFilterAceProtoShowAceId		1.3.6.1.4.1.2272.1.202.1.1.2.4.27.1.2
An index to the AceProtoShowEntry, a unique identifier for Ace entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1000

rcPrFilterAceProtoShowTcpSrcPort		1.3.6.1.4.1.2272.1.202.1.1.2.4.27.1.3
Port Number or Port List to match on.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..1500)

rcPrFilterAceProtoShowTcpSrcPortOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.27.1.4
Operator for Ace Protocol TcpSrcPort.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	eq(1), ne(2), le(3), ge(4), any(255)

rcPrFilterAceProtoShowUdpSrcPort		1.3.6.1.4.1.2272.1.202.1.1.2.4.27.1.5
Port Number or Port List to match on.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..1500)

rcPrFilterAceProtoShowUdpSrcPortOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.27.1.6
Operator for Ace Protocol UdpSrcPort.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	eq(1), ne(2), le(3), ge(4), any(255)

rcPrFilterAceProtoShowTcpDstPort		1.3.6.1.4.1.2272.1.202.1.1.2.4.27.1.7
Port Number or Port List to match on.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..1500)

rcPrFilterAceProtoShowTcpDstPortOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.27.1.8
Operator for Ace Protocol TcpDstPort.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	eq(1), ne(2), le(3), ge(4), any(255)

rcPrFilterAceProtoShowUdpDstPort		1.3.6.1.4.1.2272.1.202.1.1.2.4.27.1.9
Port Number or Port List to match on.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..1500)

rcPrFilterAceProtoShowUdpDstPortOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.27.1.10
Operator for Ace Protocol UdpDstPort.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	eq(1), ne(2), le(3), ge(4), any(255)

rcPrFilterAceProtoShowIcmpMsgTypeList		1.3.6.1.4.1.2272.1.202.1.1.2.4.27.1.11
One or a list of Icmp messages to be matched. Need to provide strings, number of protocol header types (pre-defined values plus user-defined headers). Valid range is 0 to 255 (reserved).
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..1500)

rcPrFilterAceProtoShowIcmpMsgTypeOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.27.1.12
Operator for Ace Protocol IcmpMsgTypes.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	eq(1), ne(2), any(255)

rcPrFilterAceProtoShowTcpFlagsList		1.3.6.1.4.1.2272.1.202.1.1.2.4.27.1.13
One or a list of Tcp flags to be matched. Need to provide strings, number of protocol header types (pre-defined values plus user-defined headers). Valid range is 0 to 63
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..1500)

rcPrFilterAceProtoShowTcpFlagsOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.27.1.14
Operator for Ace Protocol TcpFlags.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	matchAny(6), matchAll(7), any(255)

rcPrFilterAcePatternShowTable		1.3.6.1.4.1.2272.1.202.1.1.2.4.28
A table of Aces to store Pattern 1, 2, 3 Header information of each Ace in context of its parent Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrFilterAcePatternShowEntry

rcPrFilterAcePatternShowEntry		1.3.6.1.4.1.2272.1.202.1.1.2.4.28.1
One Ace entry holding Ace Pattern 1, 2, 3 information. Ace is a member of one Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrFilterAcePatternShowEntry

rcPrFilterAcePatternShowAclId		1.3.6.1.4.1.2272.1.202.1.1.2.4.28.1.1
An index to the AcePatternEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4096

rcPrFilterAcePatternShowAceId		1.3.6.1.4.1.2272.1.202.1.1.2.4.28.1.2
An index to the AcePatternEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1000

rcPrFilterAcePatternShowPattern1Name		1.3.6.1.4.1.2272.1.202.1.1.2.4.28.1.3
A descriptive name chosen by the administrator for the Ace Pattern Entry.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..32)

rcPrFilterAcePatternShowPattern1Value		1.3.6.1.4.1.2272.1.202.1.1.2.4.28.1.4
Set the pattern value as numeric string. The numeric value of each byte is encoded in one octet of the string. Unused bytes are left at the trailing end of string. The number of bytes to extract from this string is set in rcPrFilterActPatternLength.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..1500)

rcPrFilterAcePatternShowPattern1Oper		1.3.6.1.4.1.2272.1.202.1.1.2.4.28.1.5
Operators for Ace Pattern.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	eq(1), le(3), ge(4), any(255)

rcPrFilterAcePatternShowPattern2Name		1.3.6.1.4.1.2272.1.202.1.1.2.4.28.1.6
A descriptive name chosen by the administrator for the Ace Pattern Entry.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..32)

rcPrFilterAcePatternShowPattern2Value		1.3.6.1.4.1.2272.1.202.1.1.2.4.28.1.7
Set the pattern value as numeric string. The numeric value of each byte is encoded in one octet of the string. Unused bytes are left at the trailing end of string. The number of bytes to extract from this string is set in rcPrFilterActPatternLength.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..1500)

rcPrFilterAcePatternShowPattern2Oper		1.3.6.1.4.1.2272.1.202.1.1.2.4.28.1.8
Operators for Ace Pattern.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	eq(1), le(3), ge(4), any(255)

rcPrFilterAcePatternShowPattern3Name		1.3.6.1.4.1.2272.1.202.1.1.2.4.28.1.9
A descriptive name chosen by the administrator for the Ace Pattern Entry.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..32)

rcPrFilterAcePatternShowPattern3Value		1.3.6.1.4.1.2272.1.202.1.1.2.4.28.1.10
Set the pattern value as numeric string. The numeric value of each byte is encoded in one octet of the string. Unused bytes are left at the trailing end of string. The number of bytes to extract from this string is set in rcPrFilterActPatternLength.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..1500)

rcPrFilterAcePatternShowPattern3Oper		1.3.6.1.4.1.2272.1.202.1.1.2.4.28.1.11
Operators for Ace Pattern.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	eq(1), le(3), ge(4), any(255)

rcPrFilterAceIpv6SrcAddrTable		1.3.6.1.4.1.2272.1.202.1.1.2.4.29
A table of Aces to store IPv6 Source Address Header information of each Ace in context of its parent Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrFilterAceIpv6SrcAddrEntry

rcPrFilterAceIpv6SrcAddrEntry		1.3.6.1.4.1.2272.1.202.1.1.2.4.29.1
One Ace entry holding Ace IPv6 Source Address Header information. An Ace is a member of one Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrFilterAceIpv6SrcAddrEntry

rcPrFilterAceIpv6SrcAddrAclId		1.3.6.1.4.1.2272.1.202.1.1.2.4.29.1.1
An index to the AceIpv6SrcAddrEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4096

rcPrFilterAceIpv6SrcAddrAceId		1.3.6.1.4.1.2272.1.202.1.1.2.4.29.1.2
An index to the AceIpv6SrcAddrEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1000

rcPrFilterAceIpv6SrcAddrList		1.3.6.1.4.1.2272.1.202.1.1.2.4.29.1.3
The list of ipv6 source address to match from IPv6 header.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..1500)

rcPrFilterAceIpv6SrcAddrListCount		1.3.6.1.4.1.2272.1.202.1.1.2.4.29.1.4
Count to store the number of discrete ranges entered for the ipv6 src address.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..100

rcPrFilterAceIpv6SrcAddrOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.29.1.5
Operators for Ace Ipv6 Source Address.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	eq(1), ne(2)

rcPrFilterAceIpv6SrcAddrRowStatus		1.3.6.1.4.1.2272.1.202.1.1.2.4.29.1.6
Create/delete operations for this entry.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcPrFilterAceIpv6DstAddrTable		1.3.6.1.4.1.2272.1.202.1.1.2.4.30
A table of Aces to store IPv6 Destination Address Header information of each Ace in context of its parent Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrFilterAceIpv6DstAddrEntry

rcPrFilterAceIpv6DstAddrEntry		1.3.6.1.4.1.2272.1.202.1.1.2.4.30.1
One Ace entry holding Ace IPv6 Destination Address Header information. An Ace is a member of one Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrFilterAceIpv6DstAddrEntry

rcPrFilterAceIpv6DstAddrAclId		1.3.6.1.4.1.2272.1.202.1.1.2.4.30.1.1
An index to the AceIpv6DstAddrEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4096

rcPrFilterAceIpv6DstAddrAceId		1.3.6.1.4.1.2272.1.202.1.1.2.4.30.1.2
An index to the AceIpv6DstAddrEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1000

rcPrFilterAceIpv6DstAddrList		1.3.6.1.4.1.2272.1.202.1.1.2.4.30.1.3
The list of ipv6 dst address to match from IPv6 header.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..1500)

rcPrFilterAceIpv6DstAddrListCount		1.3.6.1.4.1.2272.1.202.1.1.2.4.30.1.4
Count to store the number of discrete ranges entered for the IPv6 Destination Address.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..100

rcPrFilterAceIpv6DstAddrOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.30.1.5
Operators for Ace IPv6 Destination Address.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	eq(1), ne(2)

rcPrFilterAceIpv6DstAddrRowStatus		1.3.6.1.4.1.2272.1.202.1.1.2.4.30.1.6
Create/delete operations for this entry.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcPrFilterAceIpv6NextHdrTable		1.3.6.1.4.1.2272.1.202.1.1.2.4.31
A table of Aces to store IPv6 Next header Header information of each Ace in context of its parent Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrFilterAceIpv6NextHdrEntry

rcPrFilterAceIpv6NextHdrEntry		1.3.6.1.4.1.2272.1.202.1.1.2.4.31.1
One Ace entry holding Ace IPv6 Next header information. An Ace is a member of one Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrFilterAceIpv6NextHdrEntry

rcPrFilterAceIpv6NextHdrAclId		1.3.6.1.4.1.2272.1.202.1.1.2.4.31.1.1
An index to the AceIpv6NextHdrEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4096

rcPrFilterAceIpv6NextHdrAceId		1.3.6.1.4.1.2272.1.202.1.1.2.4.31.1.2
An index to the AceIpv6NextHdrEntry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1000

rcPrFilterAceIpv6NextHdrNextHdr		1.3.6.1.4.1.2272.1.202.1.1.2.4.31.1.3
The ipv6 next header to look for.
Status: current	Access: read-write
OBJECT-TYPE
	Ipv6NextHdr

rcPrFilterAceIpv6NextHdrOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.31.1.4
Operators for Ace IPv6 Next header.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	eq(1), ne(2)

rcPrFilterAceIpv6NextHdrRowStatus		1.3.6.1.4.1.2272.1.202.1.1.2.4.31.1.5
Create/delete operations for this entry.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcPrFilterAceIpv6ShowTable		1.3.6.1.4.1.2272.1.202.1.1.2.4.32
A table of Aces to display ipv6 information of each Ace in context of its parent Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPrFilterAceIpv6ShowEntry

rcPrFilterAceIpv6ShowEntry		1.3.6.1.4.1.2272.1.202.1.1.2.4.32.1
One Ace entry holding Ace ipv6 information. Ace is a member of one Acl.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPrFilterAceIpv6ShowEntry

rcPrFilterAceIpv6ShowAclId		1.3.6.1.4.1.2272.1.202.1.1.2.4.32.1.1
An index to the AceIpv6Entry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4096

rcPrFilterAceIpv6ShowAceId		1.3.6.1.4.1.2272.1.202.1.1.2.4.32.1.2
An index to the AceIpv6Entry, a unique identifier for Acl entry in the range of Table Size.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1000

rcPrFilterAceIpv6ShowSrcAddrList		1.3.6.1.4.1.2272.1.202.1.1.2.4.32.1.3
The list of v6 source address to display.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..1500)

rcPrFilterAceIpv6ShowSrcAddrOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.32.1.4
Operators for Ace v6 Source Address.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	eq(1), ne(2), any(255)

rcPrFilterAceIpv6ShowDstAddrList		1.3.6.1.4.1.2272.1.202.1.1.2.4.32.1.5
List of v6 destination address to display.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..1500)

rcPrFilterAceIpv6ShowDstAddrOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.32.1.6
Operators for Ace v6 Destination Address.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	eq(1), ne(2), any(255)

rcPrFilterAceIpv6ShowNxtHdrNxtHdr		1.3.6.1.4.1.2272.1.202.1.1.2.4.32.1.7
v6 next hdr to display.
Status: current	Access: read-only
OBJECT-TYPE
	Ipv6NextHdr

rcPrFilterAceIpv6ShowNxtHdrOper		1.3.6.1.4.1.2272.1.202.1.1.2.4.32.1.8
Operator for Ace v6 next hdr.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	eq(1), ne(2), any(255)

rcVrfMib		1.3.6.1.4.1.2272.1.203.1
OBJECT IDENTIFIER

rcVrfNotifications		1.3.6.1.4.1.2272.1.203.1.0
OBJECT IDENTIFIER

rcVrfObjects		1.3.6.1.4.1.2272.1.203.1.1
OBJECT IDENTIFIER

rcVrfNotificationObjects		1.3.6.1.4.1.2272.1.203.1.2
OBJECT IDENTIFIER

rcVrfConfig		1.3.6.1.4.1.2272.1.203.1.1.1
OBJECT IDENTIFIER

rcVrfConfigScalars		1.3.6.1.4.1.2272.1.203.1.1.1.1
OBJECT IDENTIFIER

rcVrfConfigNextAvailableVrfId		1.3.6.1.4.1.2272.1.203.1.1.1.1.1
The next available Virtual Router Id (index). This object provides a hint for the rcVrfId value to use when administratively creating a new rcVrfConfigEntry. A GET of this object returns the next available rcVrfId value to be used to create an entry in the associated rcVrfConfigTable; or zero, if no valid rcVrfId value is available. A value of zero(0) indicates that it is not possible to create a new rcVrfConfigEntry. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously. Unless specified otherwise by its MAX-ACCESS and DESCRIPTION clauses, an object of this type is read-only, and a SET of such an object returns a notWritable error.
Status: current	Access: read-only
OBJECT-TYPE
	VrfIdentifier

rcVrfConfigTable		1.3.6.1.4.1.2272.1.203.1.1.1.2
This table is for creating the new Virtual Routers.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcVrfConfigEntry

rcVrfConfigEntry		1.3.6.1.4.1.2272.1.203.1.1.1.2.1
The entries in this table can be added/deleted using the rcVrfRowStatus.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcVrfConfigEntry

rcVrfId		1.3.6.1.4.1.2272.1.203.1.1.1.2.1.1
The unique id of this virtual router instance. A Virtual Router cannot not be created with rcVrfId = 0. VRFID 0 is reserved for the Administrative VRF.
Status: current	Access: not-accessible
OBJECT-TYPE
	VrfIdentifier

rcVrfRowStatus		1.3.6.1.4.1.2272.1.203.1.1.1.2.1.2
The status column has three defined values: - `active', which indicates that the conceptual row is available for use by the managed device; - `createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - `destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcVrfName		1.3.6.1.4.1.2272.1.203.1.1.1.2.1.3
The Name of the Virtual Router.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..64)

rcVrfContextName		1.3.6.1.4.1.2272.1.203.1.1.1.2.1.4
The SNMPv2 Community String or SNMPv3 contextName denotes the VRF 'context' and is used to logically separate the MIB module management.
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString	Size(0..32)

rcVrfTrapEnable		1.3.6.1.4.1.2272.1.203.1.1.1.2.1.5
This objects is used to enable the generation of the VrfUp and VrfDown traps. true(1) - VRF Traps Enabled false(2) - VRF Traps Disabled
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcVrfMaxRoutes		1.3.6.1.4.1.2272.1.203.1.1.1.2.1.6
This object specifies the maximum number of routes that this VRF can support. The default value is 10000.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

rcVrfAdminStatus		1.3.6.1.4.1.2272.1.203.1.1.1.2.1.7
The administrative state of the Virtual Router.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	up(1), down(2), testing(3), unknown(4)

rcVrfVpnId		1.3.6.1.4.1.2272.1.203.1.1.1.2.1.8
The Virtual Private Network Identifier of the Virtual Router.
Status: current	Access: read-create
OBJECT-TYPE
	VPNId

rcVrfRpTrigger		8.13.1.3.6.1.4.1.2272.1.203.1.1.1.2.1.9
This object represents Routing Protocol (RP) Triggers on a Virtual Router and it meant to be used to initiate or shutdown routing protocols on a VRF. Multiple RPs can be acted on simultaneously. Also, individual RPs can be brought up in steps, which should not affect the RPs that were running. The BITS represent an Action-code that specifies what action is to be performed for the RPs. The actions are: initiate(1) or shutdown(0). The running status of an RP shall be available in the VRF stats table's rcVrfRpStatus, which has a similar format, but represents the status. Bits 0-3 may be specified in any combination. Individual routing protocols may be enabled and disabled independently. Protocols are enabled by setting the respective BIT and are disabled by resetting the BIT. So, for example, to enable RIP and BGP protocols the rcVrfRpTrigger bits 0 and 2 need to be set, and as encoded as 10100000. All zeros should be interpreted as all protocols disable.
Status: current	Access: read-create
OBJECT-TYPE
	VrfRpTriggerBitCode

rcVrfMaxRoutesTrapEnable		1.3.6.1.4.1.2272.1.203.1.1.1.2.1.10
This objects is used to enable the generation of the VRF Max Routes Exceeded traps. true(1) - VRF Max Routes Exceeded Traps Enabled false(2) - VRF Max Routes Exceeded Traps Disabled
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcVrfStat		1.3.6.1.4.1.2272.1.203.1.1.2
OBJECT IDENTIFIER

rcVrfStatScalars		1.3.6.1.4.1.2272.1.203.1.1.2.1
OBJECT IDENTIFIER

rcVrfConfiguredVRFs		1.3.6.1.4.1.2272.1.203.1.1.2.1.1
The number of VRFs configured on this network element.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcVrfActiveVRFs		1.3.6.1.4.1.2272.1.203.1.1.2.1.2
The number of VRFs that are active on the network element. These are VRFs for which the rcVrfStatOperStatus = up(1)
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcVrfStatTable		1.3.6.1.4.1.2272.1.203.1.1.2.2
This table contains statistics for the Virtual Router.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcVrfStatEntry

rcVrfStatEntry		1.3.6.1.4.1.2272.1.203.1.1.2.2.1
Entries in this table are per rcVrfId.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcVrfStatEntry

rcVrfStatRouteEntries		1.3.6.1.4.1.2272.1.203.1.1.2.2.1.1
Total number of routes for this VRF.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcVrfStatFIBEntries		1.3.6.1.4.1.2272.1.203.1.1.2.2.1.2
Total number of FIB Entries for this VRF.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcVrfStatUpTime		1.3.6.1.4.1.2272.1.203.1.1.2.2.1.3
The time in (in hundredths of a second) since this VRF entry has been operational.
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

rcVrfOperStatus		1.3.6.1.4.1.2272.1.203.1.1.2.2.1.4
The operational status of the Virtual Router.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2), unknown(3)

rcVrfRpStatus		1.3.6.1.4.1.2272.1.203.1.1.2.2.1.5
This object represents the status of Routing Protocols on this VRF corresponding to the list of RP specified in rcVrfRpTrigger. The BITS represent an Action-code that specifies the status of the RPs. The status are: initiated (1) or shutdown (0). Initiated status is indicated when the respective BIT value is 1 and indicates shutdown when the respective BIT value is 0. Bits 0-3 may appear in any combination to indicate that RPs may be enabled and disabled independently or that multiple RP are acted on simultaneously.
Status: current	Access: read-only
OBJECT-TYPE
	VrfRpTriggerBitCode

rcVrfRouterAddressType		1.3.6.1.4.1.2272.1.203.1.1.2.2.1.6
Router Address Type of this VRF.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddressType

rcVrfRouterAddress		1.3.6.1.4.1.2272.1.203.1.1.2.2.1.7
Router Address of this VRF. It is derived from one of the interfaces. If loopback interface is present, the loopback interface address can be used. However, loopback interface is optional.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddress

rcIpfixMib		1.3.6.1.4.1.2272.1.66.1
OBJECT IDENTIFIER

rcIpfixConfGlobal		1.3.6.1.4.1.2272.1.66.1.1
OBJECT IDENTIFIER

rcIpfixTable		1.3.6.1.4.1.2272.1.66.1.2
OBJECT IDENTIFIER

rcIpfixConfState		1.3.6.1.4.1.2272.1.66.1.1.1
Enables/Disables the state of ipfix on the box.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpfixConfSlotTable		1.3.6.1.4.1.2272.1.66.1.2.1
A table to store the configuration details for IPFIX for each slot. This table is indexed by slot number.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpfixConfSlotEntry

rcIpfixConfSlotEntry		1.3.6.1.4.1.2272.1.66.1.2.1.1
One Entry holding IPFIX config information on slot basis.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpfixConfSlotEntry

rcIpfixConfSlotNum		1.3.6.1.4.1.2272.1.66.1.2.1.1.1
Slot number
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..10

rcIpfixConfSlotAgingIntv		1.3.6.1.4.1.2272.1.66.1.2.1.1.2
Flow record aging interval (Value in seconds).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	10..3600

rcIpfixConfSlotActiveTimeout		1.3.6.1.4.1.2272.1.66.1.2.1.1.3
Flow record active timeout value (Value in mins).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..60

rcIpfixConfSlotExportIntv		1.3.6.1.4.1.2272.1.66.1.2.1.1.4
Frequency of flow export to collector (Value in sec).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	10..3600

rcIpfixConfSlotExportState		1.3.6.1.4.1.2272.1.66.1.2.1.1.5
State of exporter.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpfixConfSlotTempRefIntvSec		1.3.6.1.4.1.2272.1.66.1.2.1.1.6
Template refresh timeout. Template is sent out to the collector at least every x seconds or every y exported packets, whichever occurs first.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	300..3600

rcIpfixConfSlotTempRefIntvPkts		1.3.6.1.4.1.2272.1.66.1.2.1.1.7
Template refresh timeout. Template is sent out to the collector at least every x seconds or every y exported packets, whichever occurs first.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	10000..100000

rcIpfixCollectorTable		1.3.6.1.4.1.2272.1.66.1.2.2
Table to store the configuration details for IPFIX collector for each slot. This table is indexed by slot number and ip address.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpfixCollectorEntry

rcIpfixCollectorEntry		1.3.6.1.4.1.2272.1.66.1.2.2.1
One entry holds IPFIX collector config information based on slot info and collector ip address.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpfixCollectorEntry

rcIpfixCollectorSlotNum		1.3.6.1.4.1.2272.1.66.1.2.2.1.1
Slot number. An index to the CollectorEntry.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..10

rcIpfixCollectorAddressType		1.3.6.1.4.1.2272.1.66.1.2.2.1.2
IP address type of the collector. An index to the CollectorEntry.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddressType

rcIpfixCollectorAddress		1.3.6.1.4.1.2272.1.66.1.2.2.1.3
IP address of the collector. An index to the CollectorEntry.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddress

rcIpfixCollectorProtocol		1.3.6.1.4.1.2272.1.66.1.2.2.1.4
Protocol for export data from exporter to collector .
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	udp(1), tcp(2), sctp(3)

rcIpfixCollectorDestPort		1.3.6.1.4.1.2272.1.66.1.2.2.1.5
Dest port to send the requests.
Status: current	Access: read-create
OBJECT-TYPE
	InetPortNumber

rcIpfixCollectorExporterIpType		1.3.6.1.4.1.2272.1.66.1.2.2.1.6
Ip address type of the exporter for collector.
Status: current	Access: read-create
OBJECT-TYPE
	InetAddressType

rcIpfixCollectorExporterIp		1.3.6.1.4.1.2272.1.66.1.2.2.1.7
Ip address of the exporter for collector.
Status: current	Access: read-create
OBJECT-TYPE
	InetAddress

rcIpfixCollectorProtoVer		1.3.6.1.4.1.2272.1.66.1.2.2.1.8
This specifies the protocol version for ipfix.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	ipfix(1), preipfixv9(2), preipfixv5(3)

rcIpfixCollectorState		1.3.6.1.4.1.2272.1.66.1.2.2.1.9
State of the particular collector. Enable is true by default.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcIpfixCollectorRowStatus		1.3.6.1.4.1.2272.1.66.1.2.2.1.10
Used to create/delete entries.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcIpfixConfPortTable		1.3.6.1.4.1.2272.1.66.1.2.3
A table to store the configuration details for IPFIX for each port. This table is indexed by port number.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpfixConfPortEntry

rcIpfixConfPortEntry		1.3.6.1.4.1.2272.1.66.1.2.3.1
Entry holding IPFIX config information per port.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpfixConfPortEntry

rcIpfixConfPortId		1.3.6.1.4.1.2272.1.66.1.2.3.1.1
An index to the IpfixConfPortEntry, a unique identifier of the portId
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

rcIpfixConfPortSampleRate		1.3.6.1.4.1.2272.1.66.1.2.3.1.2
Used to configure the sampling rate. Sample one in every N packets.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..100000

rcIpfixConfPortHashPolyCoeffs		1.3.6.1.4.1.2272.1.66.1.2.3.1.3
Command to set hash polynomial coeffs.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	000401..FFFFFF

rcIpfixConfPortHashPolySeed		1.3.6.1.4.1.2272.1.66.1.2.3.1.4
Command to set hash polynomial seed.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	000000..FFFFFF

rcIpfixConfPortFlush		1.3.6.1.4.1.2272.1.66.1.2.3.1.5
This is used to delete all records stored in COP, or to initiate an export of all records and delete data base after the export is finished.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), flush(2), exportAndFlush(3)

rcIpfixConfPortAllTraffic		1.3.6.1.4.1.2272.1.66.1.2.3.1.6
This is used to enable/disable ipfix on all trafiic, for the specified port.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcIpfixConfPortHashKeyId		1.3.6.1.4.1.2272.1.66.1.2.3.1.7
hash key id.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	hashKeyOne(1), hashKeyTwo(2), hashKeyThree(3), hashKeyFour(4)

rcIpfixConfPortDynamicSampRate		1.3.6.1.4.1.2272.1.66.1.2.3.1.8
Indicates the dynamic sampling rate.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..100000

rcIpfixHashStatsTable		1.3.6.1.4.1.2272.1.66.1.2.4
A table of hash Statistics entries to store the statistics for each slot. This table is indexed by the slot number.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpfixHashStatsEntry

rcIpfixHashStatsEntry		1.3.6.1.4.1.2272.1.66.1.2.4.1
Entry containing hash statistics information for a particular slot.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpfixHashStatsEntry

rcIpfixHashStatsSlotNum		1.3.6.1.4.1.2272.1.66.1.2.4.1.1
A unique identifier for the table.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..10

rcIpfixHashStatsHashOverflows		1.3.6.1.4.1.2272.1.66.1.2.4.1.2
Count of hash overflows per slot.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcIpfixHashStatsHashDrops		1.3.6.1.4.1.2272.1.66.1.2.4.1.3
Count of hash drops per slot.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcIpfixHashStatsClear		1.3.6.1.4.1.2272.1.66.1.2.4.1.4
Setting this object will clear hash statistics for a slot.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	clear(1)

rcIpfixHashStatsClearTime		1.3.6.1.4.1.2272.1.66.1.2.4.1.5
The value of sysUpTime when the hash statistics were last cleared.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

rcIpfixExporterStatsTable		1.3.6.1.4.1.2272.1.66.1.2.5
A table of Exporter Statistics entries to store the statistics for each slot, each collector. This table is indexed by the slot number and collector address.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpfixExporterStatsEntry

rcIpfixExporterStatsEntry		1.3.6.1.4.1.2272.1.66.1.2.5.1
Entry containing Exporter statistics information for a particular slot and particular collector.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpfixExporterStatsEntry

rcIpfixExporterStatsSlotNum		1.3.6.1.4.1.2272.1.66.1.2.5.1.1
Index for the table, slot number.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..10

rcIpfixExporterStatsCollectorType		1.3.6.1.4.1.2272.1.66.1.2.5.1.2
Collector IP address type. This is an index for the table.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddressType

rcIpfixExporterStatsCollector		1.3.6.1.4.1.2272.1.66.1.2.5.1.3
Index for the table, collector address.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddress

rcIpfixExporterStatsOutPkts		1.3.6.1.4.1.2272.1.66.1.2.5.1.4
Number of Packets sent.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcIpfixExporterStatsOutOctets		1.3.6.1.4.1.2272.1.66.1.2.5.1.5
Number of Bytes sent.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcIpfixExporterStatsPktsLoss		1.3.6.1.4.1.2272.1.66.1.2.5.1.6
Number of Records lost.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcIpfixExporterStatsClear		1.3.6.1.4.1.2272.1.66.1.2.5.1.7
Setting this object will clear exporter statistics.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	clear(1)

rcIpfixExporterStatsClearTime		1.3.6.1.4.1.2272.1.66.1.2.5.1.8
The value of sysUpTime when exporter statistics were last cleared.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

rcIpVpn		1.3.6.1.4.1.2272.1.8.27
OBJECT IDENTIFIER

rcIpVpnRouteDistinguisherTableSize		1.3.6.1.4.1.2272.1.8.27.1
Size of Route Distinguisher Table
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpVpnRouteDistinguisherTable		1.3.6.1.4.1.2272.1.8.27.2
The Route Distinguisher Table is a table of entries.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpVpnRouteDistinguisherEntry

rcIpVpnRouteDistinguisherEntry		1.3.6.1.4.1.2272.1.8.27.2.1
The table contains route distinguisher entry for ipvpn. A route distinguisher entry can be of two types: Type 0 and Type 1. Each type is comprised as follows: Type 0 is made of the 2-byte Autonomous System Number (globally unique) as administrator field followed by a 4-byte locally assigned number field.Type 1 is made of a 4 byte IP address globally unique followed by a 2-byte locally assigned number.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpVpnRouteDistinguisherEntry

rcIpVpnVrfId		1.3.6.1.4.1.2272.1.8.27.2.1.1
The VrfId is the unique identifier of the rcIpVpnRouteDistinguisherTable. It is unique because there is only one Route-Distinguisher per Vrf i.e. there is a one-to-one mapping between the route-distinguisher and the Vrf.
Status: current	Access: not-accessible
OBJECT-TYPE
	VrfIdentifier

rcIpVpnRouteDistinguisherType		1.3.6.1.4.1.2272.1.8.27.2.1.2
The route distinguisher can be of the type Ipaddress or AS number (Autonomous System) number.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(0), asnum(1), ipaddr(2)

rcIpVpnRouteDistinguisherAddress		1.3.6.1.4.1.2272.1.8.27.2.1.3
The IpAddress is required along with the Assigned number to create a route-distinguisher entry.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

rcIpVpnRouteDistinguisherAsNumber		1.3.6.1.4.1.2272.1.8.27.2.1.4
The AS (Autonomous System) number is required along with the Assigned number to create a route-distinguisher entry.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..65535

rcIpVpnRouteDistinguisherAssignedNum		1.3.6.1.4.1.2272.1.8.27.2.1.5
The assigned number is used in combination with the IpAddress or the AS number to create an entry for the route-distinguisher.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..2147483647

rcIpVpnRouteDistinguisherRowStatus		1.3.6.1.4.1.2272.1.8.27.2.1.6
Row Status for the Route Distinguisher Table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcIpVpnRouteTargetTableSize		1.3.6.1.4.1.2272.1.8.27.3
Size of Route Target Table
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIpVpnRouteTargetTable		1.3.6.1.4.1.2272.1.8.27.4
This table specifies per-VRF route target association.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIpVpnRouteTargetEntry

rcIpVpnRouteTargetEntry		1.3.6.1.4.1.2272.1.8.27.4.1
An entry in this table is created for each route target configured for a VRF supporting a MPLS/BGP VPN instance.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIpVpnRouteTargetEntry

rcIpVpnRouteTargetIndex		1.3.6.1.4.1.2272.1.8.27.4.1.1
The Route Target Index is a unique value for the rcIpVpnRouteTargetTable. It is an incremental integer value.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..10000

rcIpVpnRouteTargetType		1.3.6.1.4.1.2272.1.8.27.4.1.2
The route target entry is identified on the basis of ipaddress for Autonomous System number.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(0), asnum(1), ipaddr(2)

rcIpVpnRouteTargetIpAddress		1.3.6.1.4.1.2272.1.8.27.4.1.3
The IpAddress is required along with the Assigned number to create a route-target entry.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

rcIpVpnRouteTargetAsNumber		1.3.6.1.4.1.2272.1.8.27.4.1.4
The AS (Autonomous System) number is required along with the Assigned number to create a route-target entry.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..65535

rcIpVpnRouteTargetAssignedNum		1.3.6.1.4.1.2272.1.8.27.4.1.5
The assigned number is used in combination with the IpAddress or the AS number to create an entry for the route-target table.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..2147483647

rcIpVpnRouteTargetRowStatus		1.3.6.1.4.1.2272.1.8.27.4.1.6
Table Row Status.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcVrfIpVpnTableSize		1.3.6.1.4.1.2272.1.203.1.1.3
Size of Vrf IpVpn Table
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcVrfIpVpnTable		1.3.6.1.4.1.2272.1.203.1.1.4
Table required to configure vpn under ip.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcVrfIpVpnTableEntry

rcVrfIpVpnTableEntry		1.3.6.1.4.1.2272.1.203.1.1.4.1
Entries in this table are per rcVrfId.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcVrfIpVpnTableEntry

rcVrfIpVpnVrfId		1.3.6.1.4.1.2272.1.203.1.1.4.1.1
The VrfId serves as the Index for the rcIpVpnVrfTable and also for the rcIpVpnRouteDistinguisherTable. It allows to connect to the vrf table to obtain other attributes like the vrf name, rcVrfMaxRoutesTrapEnable etc.
Status: current	Access: not-accessible
OBJECT-TYPE
	VrfIdentifier

rcVrfIpVpnStatus		1.3.6.1.4.1.2272.1.203.1.1.4.1.2
The status of IpVpn.
Status: current	Access: read-create
OBJECT-TYPE
	EnableValue

rcVrfIpVpnImportRTList		1.3.6.1.4.1.2272.1.203.1.1.4.1.3
The Import RT list is a list of all the route-targets attached to a particular vrf behaving in the import mode.
Status: current	Access: read-create
OBJECT-TYPE
	IdList

rcVrfIpVpnExportRTList		1.3.6.1.4.1.2272.1.203.1.1.4.1.4
The Export RT list is a list of all the route-targets attached to a particular vrf in the export mode.
Status: current	Access: read-create
OBJECT-TYPE
	IdList

rcVrfIpVpnSvcLblAllocOpt		1.3.6.1.4.1.2272.1.203.1.1.4.1.5
The service label allocation option for the ipvpn
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	perVrfperNexthop(1), perVrf(2)

rcVrfIpVpnRowStatus		1.3.6.1.4.1.2272.1.203.1.1.4.1.6
RowStatus for the Vpn Entry.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcVrfIpVpnIsidNumber		1.3.6.1.4.1.2272.1.203.1.1.4.1.7
IP VPN I-SID number.Default 0 value indicates that no i-sid has been assinged.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..16777215

rcSlppMib		1.3.6.1.4.1.2272.1.64.1
OBJECT IDENTIFIER

rcSlppNotifications		1.3.6.1.4.1.2272.1.64.1.0
OBJECT IDENTIFIER

rcSlppObjects		1.3.6.1.4.1.2272.1.64.1.1
OBJECT IDENTIFIER

rcSlppNotificationObjects		1.3.6.1.4.1.2272.1.64.1.2
OBJECT IDENTIFIER

rcSlppScalars		1.3.6.1.4.1.2272.1.64.1.1.1
OBJECT IDENTIFIER

rcSlppGlobalEnable		1.3.6.1.4.1.2272.1.64.1.1.1.1
Global enable/disable for the simple loop prevention protocol.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcSlppTransmissionInterval		1.3.6.1.4.1.2272.1.64.1.1.1.2
The interval (in seconds) for which loop detection occurs.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	500..5000

rcSlppEtherType		1.3.6.1.4.1.2272.1.64.1.1.1.3
SLPP Protocol Identification. The value is normally in Hex.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rcSlppVlanTable		1.3.6.1.4.1.2272.1.64.1.1.2
Table of VLANs for which simple loop detection occur on.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcSlppVlanEntry

rcSlppVlanEntry		1.3.6.1.4.1.2272.1.64.1.1.2.1
SLPP VLAN entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcSlppVlanEntry

rcSlppVlanVlanId		1.3.6.1.4.1.2272.1.64.1.1.2.1.1
Vlan id for which simple loop detection occurs on.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..4094

rcSlppVlanSlppEnable		1.3.6.1.4.1.2272.1.64.1.1.2.1.2
Flag to indicate whether the VLAN entry is active or not for SLPP.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcSlppVlanRowStatus		1.3.6.1.4.1.2272.1.64.1.1.2.1.3
Used to create/delete entries.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

rcSlppPortTable		1.3.6.1.4.1.2272.1.64.1.1.3
Table of ports for which simple loop detection occurs on.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcSlppPortEntry

rcSlppPortEntry		1.3.6.1.4.1.2272.1.64.1.1.3.1
SLPP Port entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcSlppPortEntry

rcSlppPortIfIndex		1.3.6.1.4.1.2272.1.64.1.1.3.1.1
Port on which simple loop detection occurs on.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

rcSlppPortPktRxThreshold		1.3.6.1.4.1.2272.1.64.1.1.3.1.2
Once the number of SLPP packets received on this port reaches this threshold action will be taken.Normally, the port will be shutdown.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..500

rcSlppPortSlppEnable		1.3.6.1.4.1.2272.1.64.1.1.3.1.3
Flag to indicate whether the port entry is active or not for SLPP.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcSlppPortIncomingVlanId		1.3.6.1.4.1.2272.1.64.1.1.3.1.5
Vlan id of the classified packet on the port brought down by SLPP.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..4094

rcSlppPortSrcNodeType		1.3.6.1.4.1.2272.1.64.1.1.3.1.6
The src node type of the received slpp Pkt.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(0), local(1), peer(2)

rcSlppIncomingVlanId		1.3.6.1.4.1.2272.1.64.1.2.1
Vlan id of the classified packet on the port brought down by SLPP.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	INTEGER	1..4094

rcSlppSrcMacAddress		1.3.6.1.4.1.2272.1.64.1.2.2
Source MAC address in the classified packet on the port brought down by SLPP.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	MacAddress

rcSlppRxPortIndex		1.3.6.1.4.1.2272.1.64.1.2.3
Port on which the SLPP packet is received.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	InterfaceIndex

rcSlppRxVlanId		1.3.6.1.4.1.2272.1.64.1.2.4
Vlan on which the SLPP packet is received.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	INTEGER	1..4094

rcnSlppPortDownEvent		1.3.6.1.4.1.2272.1.64.1.0.1
A port down event that has occurred due to SLPP. The user is notified of the expected Vlan ID along with the Vlan ID and source MAC address of the packet coming in on the port identified. The first two objects can be used to lookup instance info for port id and vlan id.
Status: obsolete	Access: accessible-for-notify
NOTIFICATION-TYPE

rcnSlppPortDownEventNew		1.3.6.1.4.1.2272.1.64.1.0.2
A port down event that has occurred due to SLPP. The trap includes the port and its Vlan which receives the packet, and along with the Vlan ID and source MAC address of the packet coming in on the port identified.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

rcMplsMib		1.3.6.1.4.1.2272.1.74.1
OBJECT IDENTIFIER

rcMplsNotifications		1.3.6.1.4.1.2272.1.74.1.0
OBJECT IDENTIFIER

rcMplsObjects		1.3.6.1.4.1.2272.1.74.1.1
OBJECT IDENTIFIER

rcMplsNotificationObjects		1.3.6.1.4.1.2272.1.74.1.2
OBJECT IDENTIFIER

rcMplsGlobalGroup		1.3.6.1.4.1.2272.1.74.1.1.1
OBJECT IDENTIFIER

rcMplsGlobalScalars		1.3.6.1.4.1.2272.1.74.1.1.1.1
OBJECT IDENTIFIER

rcMplsRouterId		1.3.6.1.4.1.2272.1.74.1.1.1.1.1
IP address of the circuitless interface to be used as router-id
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

rcMplsLdpAdminStatus		1.3.6.1.4.1.2272.1.74.1.1.1.1.2
State of global LDP - enabled or disabled
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcMplsLdpPenultimateHopPop		1.3.6.1.4.1.2272.1.74.1.1.1.1.3
State of global LDP Penultimate Hop Popping.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	implicit-null(1), explicit-null(2), disabled(3)

rcMplsLdpHelloHoldTimer		1.3.6.1.4.1.2272.1.74.1.1.1.1.4
The global Hello Hold Time in seconds.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	5..65535

rcMplsLdpSessionKeepAlive		1.3.6.1.4.1.2272.1.74.1.1.1.1.5
The global Session Keep alive in seconds.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	15..65535

rcMplsLdpPathVectorLimit		1.3.6.1.4.1.2272.1.74.1.1.1.1.6
The global path vector limit.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..255

rcMplsLdpHopCountLimit		1.3.6.1.4.1.2272.1.74.1.1.1.1.7
The global loop detect hop count limit.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..255

rcMplsLdpEgressPolicyStatus		1.3.6.1.4.1.2272.1.74.1.1.1.1.8
State of LDP Egress-policy enabled or disabled
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcMplsRsvpAdminStatus		1.3.6.1.4.1.2272.1.74.1.1.1.1.9
State of global RSVP - enabled or disabled
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcMplsRsvpPenultimateHopPop		1.3.6.1.4.1.2272.1.74.1.1.1.1.10
State of global RSVP Penultimate Hop Popping.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	implicit-null(1), explicit-null(2), disabled(3)

rcMplsRsvpHelloInterval		1.3.6.1.4.1.2272.1.74.1.1.1.1.11
The global RSVP hello interval.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0..65535

rcMplsRsvpRefreshReduction		1.3.6.1.4.1.2272.1.74.1.1.1.1.12
State of global RSVP refresh reduction - enabled or disabled
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcMplsRsvpRefreshInterval		1.3.6.1.4.1.2272.1.74.1.1.1.1.13
The global value for RSVP refresh interval.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	1..65535

rcMplsRsvpRefreshMultiplier		1.3.6.1.4.1.2272.1.74.1.1.1.1.14
The global value for RSVP refresh multiplier.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	1..255

rcMplsRsvpMessageBundling		1.3.6.1.4.1.2272.1.74.1.1.1.1.15
State of global RSVP message bundling - enabled or disabled
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcMplsLspIngressStartLabel		1.3.6.1.4.1.2272.1.74.1.1.1.1.16
The global ingress rsp start label.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..1048576

rcMplsLspEgressStartLabel		1.3.6.1.4.1.2272.1.74.1.1.1.1.17
The global egress rsp start label.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..1048576

rcMplsLspIngressPktEnable		1.3.6.1.4.1.2272.1.74.1.1.1.1.18
Enable/Disable ingress rsp pkt lsp stats
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcMplsLspEgressPktEnable		1.3.6.1.4.1.2272.1.74.1.1.1.1.19
Enable/Disable egress rsp pkt lsp stats
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcMplsLdpClearStats		1.3.6.1.4.1.2272.1.74.1.1.1.1.20
Clear global LDP Statistics.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcMplsRsvpClearStats		1.3.6.1.4.1.2272.1.74.1.1.1.1.21
Clear global RSVP Statistics.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcMplsLspClearStats		1.3.6.1.4.1.2272.1.74.1.1.1.1.22
Clear 'transmit' or 'receive' lsp statistics.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), transmit(1), receive(2)

rcMplsIpStaticFecTable		1.3.6.1.4.1.2272.1.74.1.1.1.2
This is the table of ip-static fec mappings for both RSVP and LDP .
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcMplsIpStaticFecEntry

rcMplsIpStaticFecEntry		1.3.6.1.4.1.2272.1.74.1.1.1.2.1
A static fec mapping to an rsvp lsp or ldp egress IP address.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcMplsIpStaticFecEntry

rcMplsIpStaticFecDest		1.3.6.1.4.1.2272.1.74.1.1.1.2.1.1
The statically-configured destination IP address.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rcMplsIpStaticFecMask		1.3.6.1.4.1.2272.1.74.1.1.1.2.1.2
The statically-configured destination IP mask.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rcMplsIpStaticFecTunnelName		1.3.6.1.4.1.2272.1.74.1.1.1.2.1.3
The rsvp lsp tunnel name associated with rcMplsIpStaticFecTunnelId. This field will be null if the value of rcMplsIpStaticFecTunnelId is 0.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..33)

rcMplsIpStaticFecTunnelId		1.3.6.1.4.1.2272.1.74.1.1.1.2.1.4
The rsvp lsp tunnel index (from mplsTunnelTable defined in rfc3812) if this is an rsvp Ip statically mapped address. This field will be 0 if this is an LDP Egress Address mapping.
Status: current	Access: read-create
OBJECT-TYPE
	MplsTunnelIndex

rcMplsIpStaticFecEgressAddr		1.3.6.1.4.1.2272.1.74.1.1.1.2.1.5
The LDP Egress IP Address. This field will be 0 if this is an rsvp tunnel fec mapping.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

rcMplsIpStaticFecEgressMask		1.3.6.1.4.1.2272.1.74.1.1.1.2.1.6
The LDP Egress IP Mask. This field will be 0 if this is an rsvp tunnel fec mapping.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

rcMplsIpStaticFecState		1.3.6.1.4.1.2272.1.74.1.1.1.2.1.7
Indicates the actual operational status of this static fec.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2)

rcMplsIpStaticFecRowStatus		1.3.6.1.4.1.2272.1.74.1.1.1.2.1.8
This variable is used to create, modify, and/or delete a row in this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcMplsIpFtnTable		1.3.6.1.4.1.2272.1.74.1.1.1.3
This is the table of mpls Ip FTN.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcMplsIpFtnEntry

rcMplsIpFtnEntry		1.3.6.1.4.1.2272.1.74.1.1.1.3.1
An mpls FTN entry .
Status: current	Access: not-accessible
OBJECT-TYPE
	RcMplsIpFtnEntry

rcMplsIpFtnDest		1.3.6.1.4.1.2272.1.74.1.1.1.3.1.1
The FTN destination IP address.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rcMplsIpFtnMask		1.3.6.1.4.1.2272.1.74.1.1.1.3.1.2
The FTN destination IP mask.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rcMplsIpFtnType		1.3.6.1.4.1.2272.1.74.1.1.1.3.1.3
The FTN next hop label type.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	rsvp-static(1), ldp-static(2), ldp-dynamic(3)

rcMplsIpFtnOutLabel		1.3.6.1.4.1.2272.1.74.1.1.1.3.1.4
The FTN outgoing label.
Status: current	Access: read-only
OBJECT-TYPE
	MplsLabel

rcMplsIpFtnOutIfIndex		1.3.6.1.4.1.2272.1.74.1.1.1.3.1.5
The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcMplsIpFtnNextHop		1.3.6.1.4.1.2272.1.74.1.1.1.3.1.6
The FTN next hop Ip Address.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcMplsIpIlmTable		1.3.6.1.4.1.2272.1.74.1.1.1.4
This is the table of mpls Incoming Label Mapping.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcMplsIpIlmEntry

rcMplsIpIlmEntry		1.3.6.1.4.1.2272.1.74.1.1.1.4.1
An mpls Incoming Label Map entry .
Status: current	Access: not-accessible
OBJECT-TYPE
	RcMplsIpIlmEntry

rcMplsIpIlmInLabel		1.3.6.1.4.1.2272.1.74.1.1.1.4.1.1
The Incoming Label.
Status: current	Access: not-accessible
OBJECT-TYPE
	MplsLabel

rcMplsIpIlmInIfIndex		1.3.6.1.4.1.2272.1.74.1.1.1.4.1.2
The index value which uniquely identifies the incoming interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcMplsIpIlmOutLabel		1.3.6.1.4.1.2272.1.74.1.1.1.4.1.3
The Outgoing Label.
Status: current	Access: read-only
OBJECT-TYPE
	MplsLabel

rcMplsIpIlmOutIfIndex		1.3.6.1.4.1.2272.1.74.1.1.1.4.1.4
The index value which uniquely identifies the outgoing interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcMplsIpIlmNextHop		1.3.6.1.4.1.2272.1.74.1.1.1.4.1.5
The next hop Ip Address.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcMplsIngressLspStatTable		1.3.6.1.4.1.2272.1.74.1.1.1.5
This is the table of mpls Incoming Label Stats.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcMplsIngressLspStatEntry

rcMplsIngressLspStatEntry		1.3.6.1.4.1.2272.1.74.1.1.1.5.1
An mpls Incoming Label Stat entry .
Status: current	Access: not-accessible
OBJECT-TYPE
	RcMplsIngressLspStatEntry

rcMplsIngressLspPort		1.3.6.1.4.1.2272.1.74.1.1.1.5.1.1
The incoming port for the lsp.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	64..687

rcMplsIngressLspLabel		1.3.6.1.4.1.2272.1.74.1.1.1.5.1.2
The Incoming Lsp Label.
Status: current	Access: not-accessible
OBJECT-TYPE
	MplsLabel

rcMplsIngressLspPkts		1.3.6.1.4.1.2272.1.74.1.1.1.5.1.3
Count of incoming packets for the corresponding lsp and port.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcMplsEgressLspStatTable		1.3.6.1.4.1.2272.1.74.1.1.1.6
This is the table of mpls OutGoing Label Stats.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcMplsEgressLspStatEntry

rcMplsEgressLspStatEntry		1.3.6.1.4.1.2272.1.74.1.1.1.6.1
An mpls OutGoing Label Stat entry .
Status: current	Access: not-accessible
OBJECT-TYPE
	RcMplsEgressLspStatEntry

rcMplsEgressLspPort		1.3.6.1.4.1.2272.1.74.1.1.1.6.1.1
The OutGoing port for the lsp.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	64..687

rcMplsEgressLspLabel		1.3.6.1.4.1.2272.1.74.1.1.1.6.1.2
The OutGoing Lsp Label.
Status: current	Access: not-accessible
OBJECT-TYPE
	MplsLabel

rcMplsEgressLspPkts		1.3.6.1.4.1.2272.1.74.1.1.1.6.1.3
Count of outgoing packets for the corresponding lsp and port.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcMplsRsvpGroup		1.3.6.1.4.1.2272.1.74.1.1.2
OBJECT IDENTIFIER

rcMplsRsvpSummaryGroup		1.3.6.1.4.1.2272.1.74.1.1.2.1
OBJECT IDENTIFIER

rcMplsRsvpSummaryVersion		1.3.6.1.4.1.2272.1.74.1.1.2.1.1
This is the RSVP version number.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcMplsRsvpSummaryState		1.3.6.1.4.1.2272.1.74.1.1.2.1.2
This is the RSVP protocol state.
Status: current	Access: read-only
OBJECT-TYPE
	EnableValue

rcMplsRsvpSummaryLSPRetryTimer		1.3.6.1.4.1.2272.1.74.1.1.2.1.3
This is the retry timer (secs) for the LSPs starting from this node, in case of failure. A value of zero means no retry on LSPs.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcMplsRsvpSummaryLSPRetryLimit		1.3.6.1.4.1.2272.1.74.1.1.2.1.4
This is the retry limit for the LSPs starting from this node. It indicates how many times an LSP is retried before giving up. A value of zero means try infinitely.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcMplsRsvpSummaryLSPDecayRate		1.3.6.1.4.1.2272.1.74.1.1.2.1.5
This is the decay rate (percent) for LSPs starting on this node.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcMplsRsvpSummaryPHP		1.3.6.1.4.1.2272.1.74.1.1.2.1.6
This is the configured RSVP PHP support on this node. Possible values are implicit-null, explicit-null, or disabled.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	implicit-null(1), explicit-null(2), disabled(3)

rcMplsRsvpTunnelExtTable		1.3.6.1.4.1.2272.1.74.1.1.2.2
This is the table of mpls rsvp tunnels. This table supplements the mplsTunnelTable from rfc3812.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcMplsRsvpTunnelExtEntry

rcMplsRsvpTunnelExtEntry		1.3.6.1.4.1.2272.1.74.1.1.2.2.1
An entry in the mpls tunnel table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcMplsRsvpTunnelExtEntry

rcMplsRsvpTunnelExtIndex		1.3.6.1.4.1.2272.1.74.1.1.2.2.1.1
The Tunnel Index. The value of this object should mimic the value of mplsTunnelIndex of the MplsTunnelEntry of the mpls tunnel for which this extended tunnel table entry row applies.
Status: current	Access: not-accessible
OBJECT-TYPE
	MplsTunnelIndex

rcMplsRsvpTunnelExtInstance		1.3.6.1.4.1.2272.1.74.1.1.2.2.1.2
The Tunnel Instance. The value of this object should mimic the value of mplsTunnelInstance of the MplsTunnelEntry of the mpls tunnel for which this extended tunnel table entry row applies.
Status: current	Access: not-accessible
OBJECT-TYPE
	MplsTunnelInstanceIndex

rcMplsRsvpTunnelExtIngressLSRId		1.3.6.1.4.1.2272.1.74.1.1.2.2.1.3
The Rsvp Tunnel Ingress LSR Id. The value of this object should mimic the value of the mplsTunnelIngressLSRId of the MplsTunnelEntry of the mpls tunnel for which this extended tunnel table entry row applies.
Status: current	Access: not-accessible
OBJECT-TYPE
	MplsExtendedTunnelId

rcMplsRsvpTunnelExtEgressLSRId		1.3.6.1.4.1.2272.1.74.1.1.2.2.1.4
The Rsvp Tunnel Egress LSR Id. The value of this object should mimic the value of the mplsTunnelEgressLSRId of the MplsTunnelEntry of the mpls tunnel for which this extended tunnel table entry row applies.
Status: current	Access: not-accessible
OBJECT-TYPE
	MplsExtendedTunnelId

rcMplsRsvpTunnelExtName		1.3.6.1.4.1.2272.1.74.1.1.2.2.1.5
The Name of the tunnel associated with this LSP.
Status: current	Access: read-write
OBJECT-TYPE
	SnmpAdminString

rcMplsRsvpTunnelExtSwitchover		1.3.6.1.4.1.2272.1.74.1.1.2.2.1.6
Switch this LSP from active status to inactive status or vice versa.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcMplsRsvpTunnelExtActiveStatus		1.3.6.1.4.1.2272.1.74.1.1.2.2.1.7
This is 'true' if this is the active LSP of the tunnel.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcMplsRsvpTunnelExtResStyle		1.3.6.1.4.1.2272.1.74.1.1.2.2.1.8
This is the reservation style of the tunnel.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString	Size(10)

rcMplsRsvpTunnelExtLspId		1.3.6.1.4.1.2272.1.74.1.1.2.2.1.9
This is the LSP Id of this LSP.
Status: current	Access: read-only
OBJECT-TYPE
	MplsLSPID

rcMplsRsvpTunnelExtERO		1.3.6.1.4.1.2272.1.74.1.1.2.2.1.10
This is the Explicit Route associated with this LSP.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString	Size(100)

rcMplsRsvpTunnelExtRRO		1.3.6.1.4.1.2272.1.74.1.1.2.2.1.11
This is the Recorded Route associated with this LSP.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString	Size(100)

rcMplsRsvpTunnelExtInIfIndex		1.3.6.1.4.1.2272.1.74.1.1.2.2.1.12
This is the incoming interface for the LSP. This applies to rows with mplsTunnelRole set to transit(2) or tail(3).
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcMplsRsvpTunnelExtInLabel		1.3.6.1.4.1.2272.1.74.1.1.2.2.1.13
This is the incoming Mpls Label. This applies to rows with mplsTunnelRole set to transit(2) or tail(3).
Status: current	Access: read-only
OBJECT-TYPE
	MplsLabel

rcMplsRsvpTunnelExtInNeighbor		1.3.6.1.4.1.2272.1.74.1.1.2.2.1.14
This address of the previous-hop (upstream) router. This applies to rows with mplsTunnelRole set to transit(2) or tail(3).
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcMplsRsvpTunnelExtOutIfIndex		1.3.6.1.4.1.2272.1.74.1.1.2.2.1.15
This is the outgoing interface for the LSP. This applies to rows with mplsTunnelRole set to head(1) or transit(2).
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcMplsRsvpTunnelExtOutLabel		1.3.6.1.4.1.2272.1.74.1.1.2.2.1.16
This is the outgoing Mpls Label. This applies to rows with mplsTunnelRole set to head(1) or transit(2).
Status: current	Access: read-only
OBJECT-TYPE
	MplsLabel

rcMplsRsvpTunnelExtOutNeighbor		1.3.6.1.4.1.2272.1.74.1.1.2.2.1.17
This address of the next-hop (downstream) router. This applies to rows with applies to rows with mplsTunnelRole set to head(1) or transit(2).
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcMplsRsvpTunnelExtTSpecRate		1.3.6.1.4.1.2272.1.74.1.1.2.2.1.18
This is the primary LSP TSpec Rate. This applies to rows with mplsTunnelRole set to transit(2) or tail(3).
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcMplsRsvpTunnelExtTSpecSize		1.3.6.1.4.1.2272.1.74.1.1.2.2.1.19
This is the primary LSP TSpec Size. This applies to rows with mplsTunnelRole set to transit(2) or tail(3).
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcMplsRsvpTunnelExtTSpecPeak		1.3.6.1.4.1.2272.1.74.1.1.2.2.1.20
This is the primary LSP TSpec Peak. This applies to rows with mplsTunnelRole set to transit(2) or tail(3).
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcMplsRsvpTunnelExtTSpecMin		1.3.6.1.4.1.2272.1.74.1.1.2.2.1.21
This is the primary LSP TSpec Min. This applies to rows with mplsTunnelRole set to transit(2) or tail(3).
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcMplsRsvpTunnelExtTSpecMax		1.3.6.1.4.1.2272.1.74.1.1.2.2.1.22
This is the primary lsp TSpec Max. This applies to rows with mplsTunnelRole set to transit(2) or tail(3).
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcMplsRsvpTunnelExtInstanceUpTime		1.3.6.1.4.1.2272.1.74.1.1.2.2.1.23
This is the time (in 100ths of a second) that this instance has been in the Oper 'Up' state. When the instance transitions out of the Oper 'Up' state the time is reset to zero.
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

rcMplsRsvpTunnelExtLSPUpTime		1.3.6.1.4.1.2272.1.74.1.1.2.2.1.24
This is the time (in 100ths of a second) that all instances of this LSP have been in the Oper Up state. The time is calculated based on the create time of the first instance of the LSP to go to the Oper 'Up' state. When all instances of this LSP have transitioned out of the Oper 'Up' state the time is reset to zero.
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

rcMplsRsvpNeighborTable		1.3.6.1.4.1.2272.1.74.1.1.2.3
This is the table of mpls rsvp neighbors.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcMplsRsvpNeighborEntry

rcMplsRsvpNeighborEntry		1.3.6.1.4.1.2272.1.74.1.1.2.3.1
An entry in the mpls rsvp tunnel table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcMplsRsvpNeighborEntry

rcMplsRsvpNeighborAddress		1.3.6.1.4.1.2272.1.74.1.1.2.3.1.1
This is the address of a learned neighbor.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rcMplsRsvpNeighborHelloState		1.3.6.1.4.1.2272.1.74.1.1.2.3.1.2
This is the state of hello exchange with the neighbor.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString	Size(20)

rcMplsRsvpNeighborIfIndex		1.3.6.1.4.1.2272.1.74.1.1.2.3.1.3
This is the interface index of the neighbor.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcMplsRsvpNeighborTime		1.3.6.1.4.1.2272.1.74.1.1.2.3.1.4
This is the time the neighbor was learned.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcMplsRsvpNeighborPeriod		1.3.6.1.4.1.2272.1.74.1.1.2.3.1.5
This is the RSVP Hello Interval.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcMplsRsvpNeighborSendCnt		1.3.6.1.4.1.2272.1.74.1.1.2.3.1.6
This is the number of Hello packets sent to the neighbor.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcMplsRsvpNeighborRcvCnt		1.3.6.1.4.1.2272.1.74.1.1.2.3.1.7
This is the number of Hellp packets received from the neighbor.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcMplsRsvpNeighborLocalInstance		1.3.6.1.4.1.2272.1.74.1.1.2.3.1.8
This is the identification sent to the remote router during Hello message exchange.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcMplsRsvpNeighborRemoteInstance		1.3.6.1.4.1.2272.1.74.1.1.2.3.1.9
This is the identification provided by the remote router during Hello message exchange.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcMplsRsvpNeighborCreationTime		1.3.6.1.4.1.2272.1.74.1.1.2.3.1.10
This is the time the neighbor instance was created.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcMplsRsvpNeighborLastPktRxTime		1.3.6.1.4.1.2272.1.74.1.1.2.3.1.11
This is the time that the last Hello message was received from the remote router.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcMplsRsvpNeighborRefReduction		1.3.6.1.4.1.2272.1.74.1.1.2.3.1.12
This is the refresh-reduction status between the local router and the neighbor.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString	Size(50)

rcMplsRsvpInterfaceTable		1.3.6.1.4.1.2272.1.74.1.1.2.4
This is the table of mpls rsvp interfaces.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcMplsRsvpInterfaceEntry

rcMplsRsvpInterfaceEntry		1.3.6.1.4.1.2272.1.74.1.1.2.4.1
An entry in the mpls rsvp interface table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcMplsRsvpInterfaceEntry

rcMplsRsvpInterfaceIfIndex		1.3.6.1.4.1.2272.1.74.1.1.2.4.1.1
This is the interface index.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

rcMplsRsvpInterfaceAddress		1.3.6.1.4.1.2272.1.74.1.1.2.4.1.2
This is the address of the interface.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcMplsRsvpInterfaceRefreshInterval		1.3.6.1.4.1.2272.1.74.1.1.2.4.1.3
This is the RSVP refresh interval for the interface(seconds).
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcMplsRsvpInterfaceRefreshMult		1.3.6.1.4.1.2272.1.74.1.1.2.4.1.4
This is the configured RSVP refresh multiplier for the interface(seconds).
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcMplsRsvpInterfaceHelloInterval		1.3.6.1.4.1.2272.1.74.1.1.2.4.1.5
This is the configured RSVP Hello Interval of the interface (seconds).
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcMplsRsvpInterfaceRefreshReduction		1.3.6.1.4.1.2272.1.74.1.1.2.4.1.6
This is the configured RSVP refresh reduction support on the interface.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcMplsRsvpInterfaceMessageBundling		1.3.6.1.4.1.2272.1.74.1.1.2.4.1.7
This indicates state of message bundling on the interface.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcMplsRsvpStatsTable		1.3.6.1.4.1.2272.1.74.1.1.2.5
This is the table of mpls rsvp statistics.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcMplsRsvpStatsEntry

rcMplsRsvpStatsEntry		1.3.6.1.4.1.2272.1.74.1.1.2.5.1
An entry in the mpls rsvp statistics table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcMplsRsvpStatsEntry

rcMplsRsvpStatsIfIndex		1.3.6.1.4.1.2272.1.74.1.1.2.5.1.1
This is the interface index. This value can be 0 or a valid interface index. When 0 the global rsvp statistics are retrieved.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

rcMplsRsvpStatsPathRcv		1.3.6.1.4.1.2272.1.74.1.1.2.5.1.2
This is the path received count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsRsvpStatsPathSent		1.3.6.1.4.1.2272.1.74.1.1.2.5.1.3
This is the path sent count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsRsvpStatsPathErrRcv		1.3.6.1.4.1.2272.1.74.1.1.2.5.1.4
This is the path error receives count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsRsvpStatsPathErrSent		1.3.6.1.4.1.2272.1.74.1.1.2.5.1.5
This is the path error sent count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsRsvpStatsPathTearRcv		1.3.6.1.4.1.2272.1.74.1.1.2.5.1.6
This is the path tear receives count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsRsvpStatsPathTearSent		1.3.6.1.4.1.2272.1.74.1.1.2.5.1.7
This is the path tear sent count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsRsvpStatsResvRcv		1.3.6.1.4.1.2272.1.74.1.1.2.5.1.8
This is the reservation received count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsRsvpStatsResvSent		1.3.6.1.4.1.2272.1.74.1.1.2.5.1.9
This is the reservation sent count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsRsvpStatsResvErrRcv		1.3.6.1.4.1.2272.1.74.1.1.2.5.1.10
This is the reservation error receives count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsRsvpStatsResvErrSent		1.3.6.1.4.1.2272.1.74.1.1.2.5.1.11
This is the reservation error sent count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsRsvpStatsResvTearRcv		1.3.6.1.4.1.2272.1.74.1.1.2.5.1.12
This is the resv tear receives count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsRsvpStatsResvTearSent		1.3.6.1.4.1.2272.1.74.1.1.2.5.1.13
This is the resv tear sent count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsRsvpStatsConfTearRcv		1.3.6.1.4.1.2272.1.74.1.1.2.5.1.14
This is the conf tear receives count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsRsvpStatsConfTearSent		1.3.6.1.4.1.2272.1.74.1.1.2.5.1.15
This is the conf tear sent count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsRsvpStatsAckRcv		1.3.6.1.4.1.2272.1.74.1.1.2.5.1.16
This is the acks receives count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsRsvpStatsAckSent		1.3.6.1.4.1.2272.1.74.1.1.2.5.1.17
This is the acks sent count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsRsvpStatsSRefreshRcv		1.3.6.1.4.1.2272.1.74.1.1.2.5.1.18
This is the summary refresh receives count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsRsvpStatsSRefreshSent		1.3.6.1.4.1.2272.1.74.1.1.2.5.1.19
This is the summary refresh sent count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsRsvpStatsHelloReqRcv		1.3.6.1.4.1.2272.1.74.1.1.2.5.1.20
This is the hello request receives count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsRsvpStatsHelloReqSent		1.3.6.1.4.1.2272.1.74.1.1.2.5.1.21
This is the hello request sent count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsRsvpStatsHelloAckRcv		1.3.6.1.4.1.2272.1.74.1.1.2.5.1.22
This is the hello ack receives count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsRsvpStatsHelloAckSent		1.3.6.1.4.1.2272.1.74.1.1.2.5.1.23
This is the hello ack sent count.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsRsvpStatsBadIpHdr		1.3.6.1.4.1.2272.1.74.1.1.2.5.1.24
This is the count of pkts with bad IP Header.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsRsvpStatsBadVersion		1.3.6.1.4.1.2272.1.74.1.1.2.5.1.25
This is the count of pkts with Bad Version.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsRsvpStatsBadRsvpLen		1.3.6.1.4.1.2272.1.74.1.1.2.5.1.26
This is the count of pkts with Bad Rsvp length.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsRsvpStatsBadCksum		1.3.6.1.4.1.2272.1.74.1.1.2.5.1.27
This is the count of pkts with Bad Checksum.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsRsvpStatsBadMsgType		1.3.6.1.4.1.2272.1.74.1.1.2.5.1.28
This is the count of pkts with Bad Message type.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsRsvpStatsBadMsgForm		1.3.6.1.4.1.2272.1.74.1.1.2.5.1.29
This is the count of pkts with Bad Message Form.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsRsvpStatsBadIntf		1.3.6.1.4.1.2272.1.74.1.1.2.5.1.30
This is the count of pkts received on a Bad Interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsRsvpStatsClear		1.3.6.1.4.1.2272.1.74.1.1.2.5.1.31
Clear RSVP Statistics for the interface.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcMplsLdpGroup		1.3.6.1.4.1.2272.1.74.1.1.3
OBJECT IDENTIFIER

rcMplsLdpSummaryGroup		1.3.6.1.4.1.2272.1.74.1.1.3.1
OBJECT IDENTIFIER

rcMplsLdpSummaryIntAdjCount		1.3.6.1.4.1.2272.1.74.1.1.3.1.1
This is the LDP summary index.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcMplsLdpSummaryExtAdjCount		1.3.6.1.4.1.2272.1.74.1.1.3.1.2
This is the LDP summary index.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcMplsLdpSummarySessionCount		1.3.6.1.4.1.2272.1.74.1.1.3.1.3
This is the LDP summary session count.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcMplsLdpSummaryRouteCount		1.3.6.1.4.1.2272.1.74.1.1.3.1.4
This is the LDP summary route count.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcMplsLdpSummaryLdpId		1.3.6.1.4.1.2272.1.74.1.1.3.1.5
This is the LDP summary Local LDP Id.
Status: current	Access: read-only
OBJECT-TYPE
	MplsLdpIdentifier

rcMplsLdpSummaryLspCount		1.3.6.1.4.1.2272.1.74.1.1.3.1.6
This is the LDP summary LSP count.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcMplsLdpSummaryInSegCount		1.3.6.1.4.1.2272.1.74.1.1.3.1.7
This is the LDP summary in segment count.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcMplsLdpSummaryOutSegCount		1.3.6.1.4.1.2272.1.74.1.1.3.1.8
This is the LDP summary out segment count.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcMplsLdpSummaryRedistConn		1.3.6.1.4.1.2272.1.74.1.1.3.1.9
This is the LDP policy redist enable flag.
Status: current	Access: read-only
OBJECT-TYPE
	EnableValue

rcMplsLdpDiscoveryTable		1.3.6.1.4.1.2272.1.74.1.1.3.2
This is the table of mpls ldp discoveries.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcMplsLdpDiscoveryEntry

rcMplsLdpDiscoveryEntry		1.3.6.1.4.1.2272.1.74.1.1.3.2.1
An entry in the mpls ldp discovery table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcMplsLdpDiscoveryEntry

rcMplsLdpDiscoveryIfIndex		1.3.6.1.4.1.2272.1.74.1.1.3.2.1.1
This is the interface index.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

rcMplsLdpDiscoveryPeerLdpId		1.3.6.1.4.1.2272.1.74.1.1.3.2.1.2
This is the peer ldp id.
Status: current	Access: not-accessible
OBJECT-TYPE
	MplsLdpIdentifier

rcMplsLdpDiscoveryPeerTransportAddr		1.3.6.1.4.1.2272.1.74.1.1.3.2.1.3
This is the peer transport address to which an LDP session has been provisioned.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcMplsLdpDiscoveryNegotiatedHoldTime		1.3.6.1.4.1.2272.1.74.1.1.3.2.1.4
This is the hold time negotiated between peers.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcMplsLdpDiscoveryConfSeqNum		1.3.6.1.4.1.2272.1.74.1.1.3.2.1.5
This is the configured sequence number sent by the peer.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcMplsLdpDiscoveryExtendedDiscovery		1.3.6.1.4.1.2272.1.74.1.1.3.2.1.6
If set to 1, extended discovery is enabled. If set to 0, basic discovery is enabled.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcMplsLdpPathTable		1.3.6.1.4.1.2272.1.74.1.1.3.3
This is the table of mpls LDP Paths between a local peer and a remote peer .
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcMplsLdpPathEntry

rcMplsLdpPathEntry		1.3.6.1.4.1.2272.1.74.1.1.3.3.1
An entry in the mpls ldp path table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcMplsLdpPathEntry

rcMplsLdpPathType		1.3.6.1.4.1.2272.1.74.1.1.3.3.1.1
This is the path type. ATG_NHR_LDP_FEC_TYPE_NONE 0 ATG_NHR_LDP_FEC_TYPE_HOST 1 ATG_NHR_LDP_FEC_TYPE_PREFIX 2 ATG_NHR_LDP_FEC_TYPE_VC 3 ATG_NHR_LDP_FEC_TYPE_VC_GEN_ID 4.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	none(0), host(1), prefix(2), vc(3), vcgenid(4)

rcMplsLdpPathAddrType		1.3.6.1.4.1.2272.1.74.1.1.3.3.1.2
This is the path address type.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddressType

rcMplsLdpPathAddrPrefixLength		1.3.6.1.4.1.2272.1.74.1.1.3.3.1.3
This is the path address prefix length.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddressPrefixLength

rcMplsLdpPathAddr		1.3.6.1.4.1.2272.1.74.1.1.3.3.1.4
This is the path address.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddress

rcMplsLdpPathInLabel		1.3.6.1.4.1.2272.1.74.1.1.3.3.1.5
This is the path address prefix length.
Status: current	Access: read-only
OBJECT-TYPE
	MplsLabel

rcMplsLdpPathRemotePeerTable		1.3.6.1.4.1.2272.1.74.1.1.3.4
This is the table of LDP paths to a given remote peer.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcMplsLdpPathRemotePeerEntry

rcMplsLdpPathRemotePeerEntry		1.3.6.1.4.1.2272.1.74.1.1.3.4.1
An entry in the mpls ldp path remote peer table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcMplsLdpPathRemotePeerEntry

rcMplsLdpPathRemotePeerType		1.3.6.1.4.1.2272.1.74.1.1.3.4.1.1
This is the path type. ATG_NHR_LDP_FEC_TYPE_NONE 0 ATG_NHR_LDP_FEC_TYPE_HOST 1 ATG_NHR_LDP_FEC_TYPE_PREFIX 2 ATG_NHR_LDP_FEC_TYPE_VC 3 ATG_NHR_LDP_FEC_TYPE_VC_GEN_ID 4.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	none(0), host(1), prefix(2), vc(3), vcgenid(4)

rcMplsLdpPathRemotePeerAddrType		1.3.6.1.4.1.2272.1.74.1.1.3.4.1.2
This is the type of the path address.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddressType

rcMplsLdpPathRemotePeerAddrPrefixLength		1.3.6.1.4.1.2272.1.74.1.1.3.4.1.3
This is the path address prefix length.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddressPrefixLength

rcMplsLdpPathRemotePeerAddr		1.3.6.1.4.1.2272.1.74.1.1.3.4.1.4
This is the path address.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddress

rcMplsLdpPathRemotePeerId		1.3.6.1.4.1.2272.1.74.1.1.3.4.1.5
This is the Id of the remote peer of the path.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..8

rcMplsLdpPathRemotePeerLdpId		1.3.6.1.4.1.2272.1.74.1.1.3.4.1.6
This is the LDP Id of the remote peer of the path.
Status: current	Access: read-only
OBJECT-TYPE
	MplsLdpIdentifier

rcMplsLdpPathRemotePeerOutLabel		1.3.6.1.4.1.2272.1.74.1.1.3.4.1.7
This is the Out Label for this instance of the Remote Peer Id.
Status: current	Access: read-only
OBJECT-TYPE
	MplsLabel

rcMplsLdpPathRemotePeerState		1.3.6.1.4.1.2272.1.74.1.1.3.4.1.8
This is the state of the remote peer.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	active(1), inactive(2)

rcMplsLdpRouteTable		1.3.6.1.4.1.2272.1.74.1.1.3.5
This is the table of mpls ldp routes.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcMplsLdpRouteEntry

rcMplsLdpRouteEntry		1.3.6.1.4.1.2272.1.74.1.1.3.5.1
An entry in the mpls ldp route table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcMplsLdpRouteEntry

rcMplsLdpRouteType		1.3.6.1.4.1.2272.1.74.1.1.3.5.1.1
This is the route type. ATG_NHR_LDP_FEC_TYPE_NONE 0 ATG_NHR_LDP_FEC_TYPE_HOST 1 ATG_NHR_LDP_FEC_TYPE_PREFIX 2 ATG_NHR_LDP_FEC_TYPE_VC 3 ATG_NHR_LDP_FEC_TYPE_VC_GEN_ID 4.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	none(0), host(1), prefix(2), vc(3), vcgenid(4)

rcMplsLdpRouteAddrType		1.3.6.1.4.1.2272.1.74.1.1.3.5.1.2
This is the route address prefix length.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddressType

rcMplsLdpRouteAddrPrefixLength		1.3.6.1.4.1.2272.1.74.1.1.3.5.1.3
This is the route address prefix length.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddressPrefixLength

rcMplsLdpRouteAddr		1.3.6.1.4.1.2272.1.74.1.1.3.5.1.4
This is the route address.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddress

rcMplsLdpRouteIfIndex		1.3.6.1.4.1.2272.1.74.1.1.3.5.1.5
This is the interface index of the route entry.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcMplsLdpRouteNextHopAddrType		1.3.6.1.4.1.2272.1.74.1.1.3.5.1.6
This is the address type of the next hop.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddressType

rcMplsLdpRouteNextHopAddr		1.3.6.1.4.1.2272.1.74.1.1.3.5.1.7
This is the address of the next hop.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddress

rcMplsLdpSessionTable		1.3.6.1.4.1.2272.1.74.1.1.3.6
This is the table of mpls ldp sessions.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcMplsLdpSessionEntry

rcMplsLdpSessionEntry		1.3.6.1.4.1.2272.1.74.1.1.3.6.1
An entry in the mpls ldp session table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcMplsLdpSessionEntry

rcMplsLdpSessionEntityLdpId		1.3.6.1.4.1.2272.1.74.1.1.3.6.1.1
This is the entity LDP ID for the session.
Status: current	Access: not-accessible
OBJECT-TYPE
	MplsLdpIdentifier

rcMplsLdpSessionEntityIndex		1.3.6.1.4.1.2272.1.74.1.1.3.6.1.2
This is the entity LDP ID for the session.
Status: current	Access: not-accessible
OBJECT-TYPE
	IndexInteger

rcMplsLdpSessionPeerLdpId		1.3.6.1.4.1.2272.1.74.1.1.3.6.1.3
This is the peer LDP ID for the session.
Status: current	Access: not-accessible
OBJECT-TYPE
	MplsLdpIdentifier

rcMplsLdpSessionStateLastChange		1.3.6.1.4.1.2272.1.74.1.1.3.6.1.4
The time this Session entered its current state as denoted by the rcMplsLdpSessionState object.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcMplsLdpSessionState		1.3.6.1.4.1.2272.1.74.1.1.3.6.1.5
The current state of the session, all of the states 1 to 5 are based on the state machine for session negotiation behavior 1- nonexistent, 2- initialized, 3- openrec, 4- opensent, 5- operational.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	nonexistent(1), initialized(2), openrec(3), opensent(4), operational(5)

rcMplsLdpSessionRole		1.3.6.1.4.1.2272.1.74.1.1.3.6.1.6
During session establishment the LSR/LER takes either the active role or the passive role based on address comparisons. This object indicates whether this LSR/LER was behaving in an active role or passive role during this session's establishment, 1- unknown, 2- active, 3- passive. The value of unknown(1), indicates that the role is not able to be determined at the present time.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), active(2), passive(3)

rcMplsLdpSessionProtocolVersion		1.3.6.1.4.1.2272.1.74.1.1.3.6.1.7
This is the protocol version.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcMplsLdpSessionKeepAliveHoldTimeRem		1.3.6.1.4.1.2272.1.74.1.1.3.6.1.8
This is the session keep alive hold time remaining.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcMplsLdpSessionKeepAliveTime		1.3.6.1.4.1.2272.1.74.1.1.3.6.1.9
This is the session keep alive time.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcMplsLdpSessionMaxPduLength		1.3.6.1.4.1.2272.1.74.1.1.3.6.1.10
This is the session's max pdu length.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcMplsLdpSessionDiscontinuityTime		1.3.6.1.4.1.2272.1.74.1.1.3.6.1.11
This is the session's discontinuity time.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcMplsLdpSessionHoldTime		1.3.6.1.4.1.2272.1.74.1.1.3.6.1.12
This is the session's hold time.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcMplsLdpSessionUpTime		1.3.6.1.4.1.2272.1.74.1.1.3.6.1.13
This is the session's up time.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcMplsLdpSessionMessagesSent		1.3.6.1.4.1.2272.1.74.1.1.3.6.1.14
This is the session total messages sent.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpSessionMessagesRecv		1.3.6.1.4.1.2272.1.74.1.1.3.6.1.15
This is the session total messages received.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpInterfaceTable		1.3.6.1.4.1.2272.1.74.1.1.3.7
This is the table of mpls ldp interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcMplsLdpInterfaceEntry

rcMplsLdpInterfaceEntry		1.3.6.1.4.1.2272.1.74.1.1.3.7.1
An entry in the mpls ldp interface table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcMplsLdpInterfaceEntry

rcMplsLdpInterfaceIfIndex		1.3.6.1.4.1.2272.1.74.1.1.3.7.1.1
This is the LDP interface if index.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

rcMplsLdpInterfaceNbrCount		1.3.6.1.4.1.2272.1.74.1.1.3.7.1.2
This is the number of neighbors.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcMplsLdpInterfaceNextHello		1.3.6.1.4.1.2272.1.74.1.1.3.7.1.3
This is the next hello time.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcMplsLdpInterfaceConfHoldTime		1.3.6.1.4.1.2272.1.74.1.1.3.7.1.4
This is the configured hello hold time.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcMplsLdpInterfaceNegHoldTime		1.3.6.1.4.1.2272.1.74.1.1.3.7.1.5
This is the negotiated hello hold time.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcMplsLdpInterfaceHelloInterval		1.3.6.1.4.1.2272.1.74.1.1.3.7.1.6
This is one third of the negotiated hello hold time.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcMplsLdpStatsTable		1.3.6.1.4.1.2272.1.74.1.1.3.8
This is the table of mpls ldp statistics.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcMplsLdpStatsEntry

rcMplsLdpStatsEntry		1.3.6.1.4.1.2272.1.74.1.1.3.8.1
An entry in the mpls ldp statistics table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcMplsLdpStatsEntry

rcMplsLdpStatsPeerAddress		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.1
This is the LDP Peer Address key for search. This value can be a valid peer address or 0.0.0.0. If 0.0.0.0 then global LDP statistics are retrieved.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rcMplsLdpStatsNotifyRecv		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.2
This is the count of notifications received.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpStatsNotifySent		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.3
This is the count of notifications sent.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpStatsHelloRecv		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.4
This is the count of hellos received.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpStatsHelloSent		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.5
This is the count of hellos sent.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpStatsInitRecv		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.6
This is the count of initializations received.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpStatsInitSent		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.7
This is the count of initializations sent.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpStatsKeepRecv		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.8
This is the count of keep alives received.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpStatsKeepSent		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.9
This is the count of keep alives sent.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpStatsAddrRecv		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.10
This is the count of addrs received.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpStatsAddrSent		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.11
This is the count of addrs sent.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpStatsAddrWdrRecv		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.12
This is the count of addr withdraws received.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpStatsAddrWdrSent		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.13
This is the count of addr withdraws sent.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpStatsLabelMapRecv		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.14
This is the count of label maps received.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpStatsLabelMapSent		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.15
This is the count of label maps sent.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpStatsLabelReqRecv		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.16
This is the count of label reqs received.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpStatsLabelReqSent		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.17
This is the count of label reqs sent.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpStatsLabelWdrRecv		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.18
This is the count of label withdraws received.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpStatsLabelWdrSent		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.19
This is the count of label withdraws sent.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpStatsLabelRelRecv		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.20
This is the count of label withdraws received.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpStatsLabelRelSent		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.21
This is the count of label withdraws sent.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpStatsLabelAbrRecv		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.22
This is the count of label aborts received.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpStatsLabelAbrSent		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.23
This is the count of label aborts sent.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpStatsSessionUp		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.24
This is the count of session up.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpStatsSessionDown		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.25
This is the count of session down.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpStatsBadLdpIdentifierErrors		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.26
This is the count of bad LDP ID errors.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpStatsBadPduLengthErrors		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.27
This is the count of Bad PDU length errors.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpStatsBadMessageLengthErrors		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.28
This is the count of bad message length errors.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpStatsUnknownMessageErrors		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.29
This is the count of unknown message errors.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpStatsUnknownTlvErrors		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.30
This is the count of unknown TLV errors.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpStatsBadTlvLengthErrors		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.31
This is the count of bad TLV Length errors.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpStatsMalformedTlvValueErrors		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.32
This is the count of Malinformed TLV value errors.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpStatsHoldTimerExpErrors		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.33
This is the count of hold time expired errors.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpStatsSessionRejectedNoHelloErrors		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.34
This is the count of session reject - no hello errors.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpStatsSessionRejectedBadParmAdvErrors		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.35
This is the count of session reject - bad parameter advertisement errors.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpStatsSessionRejectedMaxPduErrors		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.36
This is the count of session reject - Max PDU Errors.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpStatsSessionRejectedBadLabelRangeErrors		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.37
This is the count of session reject - Bad Label Range errors.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpStatsSessionRejectedSetupAbortErrors		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.38
This is the count of session reject - Setup Abort errors.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpStatsSessionRejectedBadKeepaliveErrors		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.39
This is the count of session reject - Bad Keepalive Errors.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpStatsSessionOtherErrors		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.40
This is the count of other errors.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMplsLdpStatsClear		1.3.6.1.4.1.2272.1.74.1.1.3.8.1.41
Clear LDP Statistics for the Peer.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcMplsLdpStatusNotificationEnable		1.3.6.1.4.1.2272.1.74.1.2.1
If this object is true, then it enables the generation of LDP Session Up or Down Traps, otherwise these traps are not emitted.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcMplsLdpSessionThresholdNotificationEnable		1.3.6.1.4.1.2272.1.74.1.2.2
If this object is true, then it enables the generation of LDP Session Threshold Exceeded Traps, otherwise these traps are not emitted.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcMplsLdpPathVectorLimitNotificationEnable		1.3.6.1.4.1.2272.1.74.1.2.3
If this object is true, then it enables the generation of LDP Path Vector Limit Exceeded Traps, otherwise these traps are not emitted.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcMsdpMib		1.3.6.1.4.1.2272.1.80.1
OBJECT IDENTIFIER

rcMsdpNotifications		1.3.6.1.4.1.2272.1.80.1.0
OBJECT IDENTIFIER

rcMsdpObjects		1.3.6.1.4.1.2272.1.80.1.1
OBJECT IDENTIFIER

rcMsdpNotificationObjects		1.3.6.1.4.1.2272.1.80.1.2
OBJECT IDENTIFIER

rcMsdpScalars		1.3.6.1.4.1.2272.1.80.1.1.1
OBJECT IDENTIFIER

rcMsdpRouteMapName		1.3.6.1.4.1.2272.1.80.1.1.1.1
Route map name. Transmit only the SA messages that meet the match criteria in the route map name with a permit keyword. It is used as the policy of the redistribute filter. It can not be set when redistribute filter is disabled.
Status: current	Access: read-write
OBJECT-TYPE
	SnmpAdminString	Size(0..64)

rcMsdpRedistributeFilterEnabled		1.3.6.1.4.1.2272.1.80.1.1.1.2
To enable or disable the redistribute filter. This filter is used to filter the (S,G,RP) entries provided by PIM to MSDP.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcMsdpRedistributeFilterApply		1.3.6.1.4.1.2272.1.80.1.1.1.3
Each time when making changes to the redistribute filter, it will not take effect until it is applied.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcMsdpImplicitDefaultPeerEnabled		1.3.6.1.4.1.2272.1.80.1.1.1.4
To enable or disable the implicit default peer of MSDP. If enabled,it will accept SA messages even if the Peer RPF(Reverse Path Forwarding) rules fails, condition is that there should be only one peer configured.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcMsdpSACacheStatsClear		1.3.6.1.4.1.2272.1.80.1.1.1.5
Clear foreign SA-Cache entries.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcMsdpPeerTable		1.3.6.1.4.1.2272.1.80.1.1.2
A table that augments the management information in the standard IETF msdpPeerTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcMsdpPeerEntry

rcMsdpPeerEntry		1.3.6.1.4.1.2272.1.80.1.1.2.1
A set of additional management information augmenting that of the standard IETF msdpPeerEntry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcMsdpPeerEntry

rcMsdpPeerAsNumber		1.3.6.1.4.1.2272.1.80.1.1.2.1.1
The AS number of the remote Peer. Value -1 indicates that AS number is not configured.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	-1..65535

rcMsdpPeerTooShortMessages		1.3.6.1.4.1.2272.1.80.1.1.2.1.2
The number of Short messages received from this peer.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMsdpPeerInBadMessages		1.3.6.1.4.1.2272.1.80.1.1.2.1.3
The number of Bad MSDP messages received from this peer.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMsdpPeerInKeepAliveMessages		1.3.6.1.4.1.2272.1.80.1.1.2.1.4
The number of keep alive messages received from this peer.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMsdpPeerOutKeepAliveMessages		1.3.6.1.4.1.2272.1.80.1.1.2.1.5
The number of keep alive messages transmitted to this peer.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMsdpPeerInSAFilterEnabled		1.3.6.1.4.1.2272.1.80.1.1.2.1.6
To enable or disable the in SA filter of a peer.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcMsdpPeerInSAFilterRouteMapName		1.3.6.1.4.1.2272.1.80.1.1.2.1.7
The route Map name of IN SA Filter. If route map name is configured, it Accepts only the SA messages that meet the match criteria in the route map map-name with a permit keyword. If access route map name is not configured, all inbound SA messages from this peer will be blocked.
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString	Size(0..64)

rcMsdpPeerOutSAFilterEnabled		1.3.6.1.4.1.2272.1.80.1.1.2.1.8
To enable or disable the out SA filter of a peer.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcMsdpPeerOutSAFilterRouteMapName		1.3.6.1.4.1.2272.1.80.1.1.2.1.9
The route Map name of OUT SA Filter. If route map name is configured, it sends only the SA messages that meet the match criteria in the route map map-name with a permit keyword. If access route map name is not configured, all outbound SA messages sent to this peer will be blocked
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString	Size(0..64)

rcMsdpPeerDescription		1.3.6.1.4.1.2272.1.80.1.1.2.1.10
Peer specific description. It is used to make the peer easier to be identified.
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString

rcMsdpPeerSALimit		1.3.6.1.4.1.2272.1.80.1.1.2.1.11
The SA Cache limit for this peer.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..6144

rcMsdpPeerMd5AuthEnabled		1.3.6.1.4.1.2272.1.80.1.1.2.1.12
The MD5 Authentication status of this peer.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcMsdpPeerMd5AuthPassword		1.3.6.1.4.1.2272.1.80.1.1.2.1.13
The MD5 Authentication password of this peer.
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString	Size(0..80)

rcMsdpPeerSAsLearnedFromThisPeer		1.3.6.1.4.1.2272.1.80.1.1.2.1.14
The total number of SAs learned from this peer.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMsdpPeerSAsAdvertisedToThisPeer		1.3.6.1.4.1.2272.1.80.1.1.2.1.15
The total number of SAs advertised to this peer.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcMsdpPeerUpOrDownTime		1.3.6.1.4.1.2272.1.80.1.1.2.1.16
MSDP Peer Up or Down duration.
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

rcMsdpPeerConnAndStatsClearedTime		1.3.6.1.4.1.2272.1.80.1.1.2.1.17
The duration of connection and statistics cleared ago.
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

rcMsdpPeerRouteMapName		1.3.6.1.4.1.2272.1.80.1.1.2.1.18
Route map name for default peer.
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString	Size(0..64)

rcMsdpPeerAdminEnabled		1.3.6.1.4.1.2272.1.80.1.1.2.1.19
The admin status of this peer.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcMsdpPeerOperEnabled		1.3.6.1.4.1.2272.1.80.1.1.2.1.20
The operational status of this peer.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcMsdpPeerDefaultPeerState		1.3.6.1.4.1.2272.1.80.1.1.2.1.21
The default peer has two state: Configured and Operational. MSDP node only accept SA messages from the Operational default peer. These is only one default peer can become Operational, all the Configured default peers are for redundancy.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	configured(1), operational(2)

rcMsdpPeerDefaultPeer		1.3.6.1.4.1.2272.1.80.1.1.2.1.22
It is used to indicate whether a peer is a default peer or not.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcMsdpSACacheTable		1.3.6.1.4.1.2272.1.80.1.1.3
SA (Source Active) - Cache Table. This table contains foreign as well as local SA Cache entries. Foreign SA Cache entries from this table will have corresponding entries in the standard table msdpSACacheTable
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcMsdpSACacheEntry

rcMsdpSACacheEntry		1.3.6.1.4.1.2272.1.80.1.1.3.1
SA Cache Entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcMsdpSACacheEntry

rcMsdpSACacheGroupAddr		1.3.6.1.4.1.2272.1.80.1.1.3.1.1
The group address of the SA Cache entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rcMsdpSACacheSourceAddr		1.3.6.1.4.1.2272.1.80.1.1.3.1.2
The source address of the SA Cache entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rcMsdpSACacheOriginRP		1.3.6.1.4.1.2272.1.80.1.1.3.1.3
The RP of the SA Cache entry. This field is in the INDEX in order to catch multiple RP's advertising the same source and group.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rcMsdpSACacheTypeInformation		1.3.6.1.4.1.2272.1.80.1.1.3.1.4
This object describes the SA cache type. It can be either local cache or foreign cache.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	local(1), foreign(2)

rcMsdpSACacheOriginatorAsNumber		1.3.6.1.4.1.2272.1.80.1.1.3.1.5
The AS number of the originator.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..65535

rcMsdpSACacheRouteType		1.3.6.1.4.1.2272.1.80.1.1.3.1.6
The owner of the route that is used for rpf checking.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	rip(1), ospf(2), static(3), bgp(4)

rcnMsdpMaxSACacheWarnSet		1.3.6.1.4.1.2272.1.80.1.0.1
This event is generated when the SA entries in the cache database exceeds 85 % of maximum value (6K) in local cache or in foreign cache.
Status: current	Access: read-only
NOTIFICATION-TYPE

rcnMsdpMaxSACacheWarnClear		1.3.6.1.4.1.2272.1.80.1.0.2
This event is generated when the Sa entries in the cache database drops to 80 % of the maximum value (6K).
Status: current	Access: read-only
NOTIFICATION-TYPE

rcnMsdpMaxSACacheErrorSet		1.3.6.1.4.1.2272.1.80.1.0.3
This event is generated when the SA entries in the cache database hits 100 % of the maximum value (6K).
Status: current	Access: read-only
NOTIFICATION-TYPE

rcnMsdpMaxSACacheErrorClear		1.3.6.1.4.1.2272.1.80.1.0.4
This event is generated when the SA entries in the cache database drops to 95% of the maximum value.
Status: current	Access: read-only
NOTIFICATION-TYPE

rcnMsdpMaxPeerSACacheWarnSet		1.3.6.1.4.1.2272.1.80.1.0.5
This event is generated when the SA entries for this peer exceeds 85 % of maximum value configured for this peer.
Status: current	Access: read-only
NOTIFICATION-TYPE

rcnMsdpMaxPeerSACacheWarnClear		1.3.6.1.4.1.2272.1.80.1.0.6
This event is generated when the SA entries for this peer drops to 80 % of the maximum value configured for this peer.
Status: current	Access: read-only
NOTIFICATION-TYPE

rcnMsdpMaxPeerSACacheErrorSet		1.3.6.1.4.1.2272.1.80.1.0.7
This event is generated when the SA entries for this peer hits 100 % of the peer SA limit.
Status: current	Access: read-only
NOTIFICATION-TYPE

rcnMsdpMaxPeerSACacheErrorClear		1.3.6.1.4.1.2272.1.80.1.0.8
This event is generated when the SA entries for this peer drops to 95% of the peer SA limit.
Status: current	Access: read-only
NOTIFICATION-TYPE

rcnMsdpEstablished		1.3.6.1.4.1.2272.1.80.1.0.9
The MSDP Established event is generated when the MSDP FSM enters the ESTABLISHED state.
Status: current	Access: read-only
NOTIFICATION-TYPE

rcnMsdpBackwardTransition		1.3.6.1.4.1.2272.1.80.1.0.10
The MSDPBackwardTransition Event is generated when the MSDP FSM moves from a higher-numbered state to a lower-numbered state.
Status: current	Access: read-only
NOTIFICATION-TYPE

rcMsdpSACacheType		1.3.6.1.4.1.2272.1.80.1.2.1
This object describes the SA cache type.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	INTEGER	local(1), foreign(2)

rcMsdpVrfId		1.3.6.1.4.1.2272.1.80.1.2.2
VRF ID for the MSDP.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	VrfIdentifier

rcVrrpTmpMib		1.3.6.1.4.1.2272.1.206.1
OBJECT IDENTIFIER

rcVrrpTmpOperations		1.3.6.1.4.1.2272.1.206.1.1
OBJECT IDENTIFIER

rcVrrpTmpStatistics		1.3.6.1.4.1.2272.1.206.1.2
OBJECT IDENTIFIER

rcVrrpTmpNotificationCntl		1.3.6.1.4.1.2272.1.206.1.1.2
Indicates whether the VRRP-enabled router will generate SNMP notifications for events defined in this MIB. 'Enabled' results in SNMP notifications; 'disabled', no notifications are sent.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

rcVrrpTmpOperationsTable		1.3.6.1.4.1.2272.1.206.1.1.7
Unified Operations table for a VRRP router which consists of a sequence (i.e., one or more conceptual rows) of 'rcVrrpTmpOperationsEntry' items which describe the operational characteristics of a virtual router.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcVrrpTmpOperationsEntry

rcVrrpTmpOperationsEntry		1.3.6.1.4.1.2272.1.206.1.1.7.1
An entry in the rcVrrpTmpOperationsTable containing the operational characteristics of a virtual router. On a VRRP router, a given virtual router is identified by a combination of the IP version, VRID and ifIndex. ifIndex represents a physical interface of the router. Note that rows in this table can be distinguished on a multi-stacked device running VRRP over IPv4 and IPv6 on the same physical interface. Rows in the table cannot be modified unless the value of 'rcVrrpTmpOperationsState' has transitioned to 'initialize'
Status: current	Access: not-accessible
OBJECT-TYPE
	RcVrrpTmpOperationsEntry

rcVrrpTmpOperationsIfIndex		1.3.6.1.4.1.2272.1.206.1.1.7.1.1
port interface index.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

rcVrrpTmpOperationsInetAddrType		1.3.6.1.4.1.2272.1.206.1.1.7.1.2
The IP address type of RcVrrpTmpOperationsEntry. This value applies to both rcVrrpTmpOperationsMasterIpAddr and rcVrrpTmpOperationsPrimaryIpAddr.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddressType

rcVrrpTmpOperationsVrId		1.3.6.1.4.1.2272.1.206.1.1.7.1.3
This object contains the Virtual Router Identifier (VRID).
Status: current	Access: not-accessible
OBJECT-TYPE
	VrId

rcVrrpTmpOperationsVirtualMacAddr		1.3.6.1.4.1.2272.1.206.1.1.7.1.4
The virtual MAC address of the virtual router. Although this object can be derived from the 'rcVrrpTmpOperationsVrId' object, it is defined so that it is easily obtainable by a management application and can be included in VRRP-related SNMP notifications.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rcVrrpTmpOperationsState		1.3.6.1.4.1.2272.1.206.1.1.7.1.5
The current state of the virtual router. This object has three defined values: - `initialize', which indicates that the virtual router is waiting for a startup event. - `backup', which indicates the virtual router is monitoring the availability of the master router. - `master', which indicates that the virtual router is forwarding packets for IP addresses that are associated with this router.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	initialize(1), backup(2), master(3)

rcVrrpTmpOperationsPriority		1.3.6.1.4.1.2272.1.206.1.1.7.1.6
This object specifies the priority to be used for the virtual router master election process. Higher values imply higher priority. A priority of '0', although not settable, is sent by the master router to indicate that this router has ceased to participate in VRRP and a backup virtual router should transition to become a new master. A priority of 255 is used for the router that owns the associated IP address(es) for VRRP over IPv4 and hence not settable. A 'badValue(3)' should be returned when a user tries to set 0 or 255 for this object.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..255

rcVrrpTmpOperationsAddrCount		1.3.6.1.4.1.2272.1.206.1.1.7.1.7
The number of IP addresses that are associated with this virtual router. This number is equal to the number of rows in the rcVrrpTmpAssociatedAddrTable that correspond to a given IP version/VRID/ifIndex.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..255

rcVrrpTmpOperationsMasterIpAddr		1.3.6.1.4.1.2272.1.206.1.1.7.1.8
The master router's real IP address. Master router would set this address to rcVrrpTmpOperationsPrimaryIpAddr while transitioning to master state. For backup routers, this is the IP address listed as the source in VRRP advertisement last received by this virtual router.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddress

rcVrrpTmpOperationsPrimaryIpAddr		1.3.6.1.4.1.2272.1.206.1.1.7.1.9
In the case where there are more than one IP Address (associated IP addresses) for a given `ifIndex', this object is used to specify the IP address that will become the rcVrrpTmpOperationsMasterIpAddr', should the virtual router transition from backup state to master.
Status: current	Access: read-create
OBJECT-TYPE
	InetAddress

rcVrrpTmpOperationsAdvInterval		1.3.6.1.4.1.2272.1.206.1.1.7.1.10
The time interval, in centiseconds, between sending advertisement messages. Only the master router sends VRRP advertisements.
Status: current	Access: read-create
OBJECT-TYPE
	TimeInterval	1..4096

rcVrrpTmpOperationsPreemptMode		1.3.6.1.4.1.2272.1.206.1.1.7.1.11
Controls whether a higher priority virtual router will preempt a lower priority master.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcVrrpTmpOperationsAcceptMode		1.3.6.1.4.1.2272.1.206.1.1.7.1.12
Controls whether a virtual router in Master state will accept packets addressed to the address owner's IPv6 address as its own if it is not the IPv6 address owner. Default is False. This object is not relevant for rows representing VRRP over IPv4 and should be set to false.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcVrrpTmpOperationsUpTime		1.3.6.1.4.1.2272.1.206.1.1.7.1.13
This is the value of the `sysUpTime' object when this virtual router (i.e., the `rcVrrpTmpOperationsState') transitioned out of `initialized'.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

rcVrrpTmpOperationsStorageType		1.3.6.1.4.1.2272.1.206.1.1.7.1.14
The storage type for this conceptual row. Write access is not required. It is optional to support nonVolatile StorageType enumeration.
Status: current	Access: read-create
OBJECT-TYPE
	StorageType

rcVrrpTmpOperationsRowStatus		1.3.6.1.4.1.2272.1.206.1.1.7.1.15
The RowStatus variable should be used in accordance to installation and removal conventions for conceptual rows. When `rcVrrpTmpOperationsRowStatus' is set to active(1), no other objects in the conceptual row can be modified. To create a row in this table, a manager sets this object to either createAndGo(4) or createAndWait(5). Until instances of all corresponding columns are appropriately configured, the value of the corresponding instance of the `rcVrrpTmpOperationsRowStatus' column will be read as notReady(3). In particular, a newly created row cannot be made active(1) until (minimally) the corresponding instance of rcVrrpTmpOperationsInetAddrType, rcVrrpTmpOperationsVrId and rcVrrpTmpOperationsPrimaryIpAddr has been set and there is at least one active row in the `rcVrrpTmpAssociatedIpAddrTable' defining an associated IP address. notInService(2) should be used to administratively bring the row down. A typical order of operation to add a row is: 1. Create a row in rcVrrpTmpOperationsTable with createAndWait(5). 2. Create one or more corresponding rows in rcVrrpTmpAssociatedIpAddrTable. 3. Populate the rcVrrpTmpOperationsEntry. 4. set rcVrrpTmpOperationsRowStatus to active(1). A typical order of operation to delete an entry is: 1. Set rcVrrpTmpOperationsRowStatus to notInService(2). 2. Set the corresponding rows in rcVrrpTmpAssociatedIpAddrTable to destroy(6) to delete the entry. 3. set rcVrrpTmpOperationsRowStatus to destroy(6) to delete the entry.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcVrrpTmpAssociatedIpAddrTable		1.3.6.1.4.1.2272.1.206.1.1.8
The table of addresses associated with this virtual router.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcVrrpTmpAssociatedIpAddrEntry

rcVrrpTmpAssociatedIpAddrEntry		1.3.6.1.4.1.2272.1.206.1.1.8.1
An entry in the table contains an IP address that is associated with a virtual router. The number of rows for a given IP version, VrID and ifIndex will equal the number of IP addresses associated (e.g., backed up) by the virtual router (equivalent to 'rcVrrpTmpOperationsIpAddrCount'). Rows in the table cannot be modified unless the value of `rcVrrpTmpOperationsState' has transitioned to `initialize'.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcVrrpTmpAssociatedIpAddrEntry

rcVrrpTmpAssociatedIpAddr		1.3.6.1.4.1.2272.1.206.1.1.8.1.1
The assigned IP addresses that a virtual router is responsible for backing up. The size of this object is either 4 or 16 depending on rcVrrpTmpOperationsInetAddrType.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddress	Size(0|4|16)

rcVrrpTmpAssociatedIpAddrPrefixLength		1.3.6.1.4.1.2272.1.206.1.1.8.1.2
The length of the prefix (in bits).
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddressPrefixLength

rcVrrpTmpAssociatedStorageType		1.3.6.1.4.1.2272.1.206.1.1.8.1.3
The storage type for this conceptual row. Write access is not required. It is optional to support nonVolatile StorageType enumeration.
Status: current	Access: read-create
OBJECT-TYPE
	StorageType

rcVrrpTmpAssociatedIpAddrRowStatus		1.3.6.1.4.1.2272.1.206.1.1.8.1.4
The RowStatus variable, used according to installation and removal conventions for conceptual rows. To create a row in this table, a manager sets this object to either createAndGo(4) or createAndWait(5). Setting this object to active(1) results in the addition of an associated address for a virtual router. Setting this object to notInService(2) results in administratively bringing down the row. Destroying the entry or setting it to destroy(6) removes the associated address from the virtual router. The use of other values is implementation-dependent. Only rcVrrpTmpAssociatedStorageType can be modified when the row is in active(1) state for Implementations supporting write access to rcVrrpTmpAssociatedStorageType Implementations should not allow deletion of the last row corresponding to an active row in rcVrrpTmpOperationsTable. Refer to description of rcVrrpTmpOperationsRowStatus for a typical row creation and deletion scenarios.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcVrrpTmpRouterChecksumErrors		1.3.6.1.4.1.2272.1.206.1.2.1
The total number of VRRP packets received with an invalid VRRP checksum value.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcVrrpTmpRouterVersionErrors		1.3.6.1.4.1.2272.1.206.1.2.2
The total number of VRRP packets received with an unknown or unsupported version number.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcVrrpTmpRouterVrIdErrors		1.3.6.1.4.1.2272.1.206.1.2.3
The total number of VRRP packets received with an invalid VRID for this virtual router.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcVrrpTmpRouterStatisticsTable		1.3.6.1.4.1.2272.1.206.1.2.5
Table of virtual router statistics.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcVrrpTmpRouterStatisticsEntry

rcVrrpTmpRouterStatisticsEntry		1.3.6.1.4.1.2272.1.206.1.2.5.1
An entry in the table, containing statistics information about a given virtual router.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcVrrpTmpRouterStatisticsEntry

rcVrrpTmpStatisticsMasterTransitions		1.3.6.1.4.1.2272.1.206.1.2.5.1.1
The total number of times that this virtual router's state has transitioned to MASTER. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of rcVrrpTmpStatisticsDiscontinuityTime.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcVrrpTmpStatisticsRcvdAdvertisements		1.3.6.1.4.1.2272.1.206.1.2.5.1.2
The total number of VRRP advertisements received by this virtual router. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of rcVrrpTmpStatisticsDiscontinuityTime.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcVrrpTmpStatisticsAdvIntervalErrors		1.3.6.1.4.1.2272.1.206.1.2.5.1.3
The total number of VRRP advertisement packets received for which the advertisement interval is different than the one configured for the local virtual router. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of rcVrrpTmpStatisticsDiscontinuityTime.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcVrrpTmpStatisticsIpTtlErrors		1.3.6.1.4.1.2272.1.206.1.2.5.1.4
The total number of VRRP packets received by the Virtual router with IPv4 TTL (for VRRP over IPv4) or IPv6 Hop Limit (for VRRP over IPv6) not equal to 255. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of rcVrrpTmpStatisticsDiscontinuityTime.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcVrrpTmpStatisticsRcvdPriZeroPackets		1.3.6.1.4.1.2272.1.206.1.2.5.1.5
The total number of VRRP packets received by the virtual router with a priority of '0'. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of rcVrrpTmpStatisticsDiscontinuityTime.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcVrrpTmpStatisticsSentPriZeroPackets		1.3.6.1.4.1.2272.1.206.1.2.5.1.6
The total number of VRRP packets sent by the virtual router with a priority of '0'. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of rcVrrpTmpStatisticsDiscontinuityTime.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcVrrpTmpStatisticsRcvdInvalidTypePkts		1.3.6.1.4.1.2272.1.206.1.2.5.1.7
The number of VRRP packets received by the virtual router with an invalid value in the 'type' field. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of rcVrrpTmpStatisticsDiscontinuityTime.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcVrrpTmpStatisticsAddressListErrors		1.3.6.1.4.1.2272.1.206.1.2.5.1.8
The total number of packets received for which the address list does not match the locally configured list for the virtual router. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of rcVrrpTmpStatisticsDiscontinuityTime.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcVrrpTmpStatisticsPacketLengthErrors		1.3.6.1.4.1.2272.1.206.1.2.5.1.9
The total number of packets received with a packet length less than the length of the VRRP header. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of rcVrrpTmpStatisticsDiscontinuityTime.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcVrrpTmpStatisticsRcvdInvalidAuthentications		1.3.6.1.4.1.2272.1.206.1.2.5.1.10
The total number of packets received with an unknown authentication type.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcVrrpTmpStatisticsDiscontinuityTime		1.3.6.1.4.1.2272.1.206.1.2.5.1.11
The value of sysUpTime on the most recent occasion at which any one or more of this entry's counters suffered a discontinuity. If no such discontinuities have occurred since the last re-initialization of the local management subsystem, then this object contains a zero value.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

rcVrrpTmpStatisticsRefreshRate		1.3.6.1.4.1.2272.1.206.1.2.5.1.12
The minimum reasonable polling interval for this entry. This object provides an indication of the minimum Amount of time required to update the counters in this entry.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcVrrpTmpNotifications		1.3.6.1.4.1.2272.1.206.1.0
OBJECT IDENTIFIER

rcVrrpTmpNewMasterReason		1.3.6.1.4.1.2272.1.206.1.1.9
This indicates the reason for rcVrrpTmpNewMaster trap. Used by rcVrrpTmpTrapNewMaster trap. The object can be polled if the rcVrrpTmpNewMaster trap is lost to identify the reason for transmission. Backup router should return notmaster(0) when pooled.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notmaster(0), priority(1), preempted(2), masterNoResponse(3)

rcVrrpTmpTrapProtoErrReason		1.3.6.1.4.1.2272.1.206.1.1.10
This indicates the reason for protocol error trap. Used by rcVrrpTmpTrapProtoError trap.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	INTEGER	hopLimitError(0), versionError(1), checksumError(2), vridError(3)

rcVrrpTmpTrapNewMaster		1.3.6.1.4.1.2272.1.206.1.0.1
The newMaster trap indicates that the sending agent has transitioned to 'Master' state.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

rcVrrpTmpTrapProtoError		1.3.6.1.4.1.2272.1.206.1.0.3
The error trap indicates that the sending agent has encountered the protocol error indicated by rcVrrpTmpTrapProtoErrorReason.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

rcVrrpExtMib		1.3.6.1.4.1.2272.1.206.2
OBJECT IDENTIFIER

rcVrrpExtObjects		1.3.6.1.4.1.2272.1.206.2.1
OBJECT IDENTIFIER

rcVrrpExtNotifications		1.3.6.1.4.1.2272.1.206.2.2
OBJECT IDENTIFIER

rcVrrpExtOperations		1.3.6.1.4.1.2272.1.206.2.3
OBJECT IDENTIFIER

rcVrrpExtScalars		1.3.6.1.4.1.2272.1.206.2.1.1
OBJECT IDENTIFIER

rcVrrpExtPingVirtualAddrEnable		1.3.6.1.4.1.2272.1.206.2.1.1.1
Used to configure whether this device should respond to pings directed to a virtual router's IPv6 address.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcVrrpExtVersionNumber		1.3.6.1.4.1.2272.1.206.2.1.1.2
The version number of Vrrp for IPv6 is 3.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	version3(3)

rcVrrpExtTrapStateTransitionType		1.3.6.1.4.1.2272.1.206.2.1.1.3
Potential types of state transitions.Used by rcVrrpv3TrapStateTransition trap.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), masterToBackup(2), backupToMaster(3), initializeToMaster(4), masterToInitialize(5), initializeToBackup(6), backupToInitialize(7)

rcVrrpExtTrapStateTransitionCause		1.3.6.1.4.1.2272.1.206.2.1.1.4
Potential types of causes that will generate a rcVrrpExtTrapStateTransition trap.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), higherPriorityAdvertizeReceived(2), shutdownReceived(3), rcVrrpAddrAndPhysicalAddrMatch(4), masterDownInterval(5), preempted(6)

rcVrrpExtOperationsVrId		1.3.6.1.4.1.2272.1.206.2.1.1.5
This object contains the Virtual Router Identifier (VRID).This is used in rcVrrpExtTrapStateTransition.
Status: current	Access: read-only
OBJECT-TYPE
	VrId

rcVrrpExtTrapStateTransition		1.3.6.1.4.1.2272.1.206.2.2.1
A rcVrrpExtTrapStateTransition trap signifies a state transition has occurred on a particular vrrp interface. Implementation of this trap is optional.
Status: current	Access: read-only
NOTIFICATION-TYPE

rcVrrpExtOperationsTable		1.3.6.1.4.1.2272.1.206.2.3.11
Unified Operations table for a VRRP router which consists of a sequence (i.e., one or more conceptual rows) of 'rcVrrpExtOperationsEntry'and 'rcVrrpTmpOperationsEntry' items which describe the operational characteristics of a virtual router. This table is an extention of 'rcVrrpTmpOperationsTable'.It contains the mib objects that are Nortel specific.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcVrrpExtOperationsEntry

rcVrrpExtOperationsEntry		1.3.6.1.4.1.2272.1.206.2.3.11.1
An entry in the rcVrrpExtOperationsTable containing the operational characteristics of a virtual router. On a VRRP router, a given virtual router is identified by a combination of the IP version, VRID and ifIndex. ifIndex represents a physical interface of the router. Note that rows in this table can be distinguished on a multi-stacked device running VRRP over IPv4 and IPv6 on the same physical interface. Rows in the table cannot be modified unless the value of 'rcVrrpTmpOperationsState' has transitioned to 'initialize'.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcVrrpExtOperationsEntry

rcVrrpExtOperationsAction		1.3.6.1.4.1.2272.1.206.2.3.11.1.1
Used to trigger an action on this vrrp interface.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	none(1), preemptHoldDownTimer(2)

rcVrrpExtOperationsBackUpMaster		1.3.6.1.4.1.2272.1.206.2.3.11.1.2
Enable the backup VRRP switch traffic forwarding. This will reduce the traffic in IST link in the time of SMLT.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

rcVrrpExtOperationsBackUpMasterState		1.3.6.1.4.1.2272.1.206.2.3.11.1.3
Indicate whether backup VRRP switch traffic forwarding is enabled or not.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2)

rcVrrpExtOperationsCriticalIpAddr		1.3.6.1.4.1.2272.1.206.2.3.11.1.4
IP address of the interface that will cause a shutdown event.Only IPv6 address is supported as of now.
Status: current	Access: read-create
OBJECT-TYPE
	InetAddress

rcVrrpExtOperationsCriticalIpAddrEnabled		1.3.6.1.4.1.2272.1.206.2.3.11.1.5
Indicate if an user-defined critical IP address should be enabled. 'NO' = use the default IP address (::). No effect if an user-defined IP address does not exist.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcVrrpExtOperationsControl		1.3.6.1.4.1.2272.1.206.2.3.11.1.6
This object will enable/disable the virtual router function. Setting the value to 'enabled', will transition the state of the router from 'initialize to 'backup'; Setting the value to 'disabled', will tranisition the router from 'master' or 'backup' to 'initialize'.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

rcVrrpExtOperationsHoldDownTimer		1.3.6.1.4.1.2272.1.206.2.3.11.1.7
Used to configure the amount of time (in seconds) to wait before preempting the current vrrp master.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..21600

rcVrrpExtOperationsHoldDownState		1.3.6.1.4.1.2272.1.206.2.3.11.1.8
Used to indicate the hold-down state of this vrrp interface. If the hold-down timer is operational this variable will be set to 'active'. 'dormant' otherwise.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	dormant(1), active(2)

rcVrrpExtOperationsHoldDownTimeRemaining		1.3.6.1.4.1.2272.1.206.2.3.11.1.9
Used to indicate the amount of time (in seconds) left before the rcVrrpExtOperationsHoldDownTimer will expire.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..21600

rcVrrpExtOperationsFasterAdvInterval		1.3.6.1.4.1.2272.1.206.2.3.11.1.10
This is the faster advertisement interval, in milliseconds, between sending advertisement messages. When the faster advertisement interval enable is checked, the faster advertisement interval is being used instead of the regular advertisement interval.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	200..1000

rcVrrpExtOperationsFasterAdvIntervalEnabled		1.3.6.1.4.1.2272.1.206.2.3.11.1.11
Used to indicate if the Faster Advertisement Interval should be used.'Disable' means use regular Advertisement interval.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

rcVrrpExtOperationsLinkLocalAddr		1.3.6.1.4.1.2272.1.206.2.3.11.1.12
The assigned Linklocal addresses to the virtual router interface. This mib object support only IPv6 address as of now.
Status: current	Access: read-create
OBJECT-TYPE
	InetAddress

rcVrrpExtOperationsGlobalIpAddr		1.3.6.1.4.1.2272.1.206.2.3.11.1.13
The assigned Global addresses to the virtual router interface. This mib object support only IPv6 address as of now.
Status: current	Access: read-create
OBJECT-TYPE
	InetAddress

rcIsis		1.3.6.1.4.1.2272.1.63
OBJECT IDENTIFIER

rcIsisGlobalGroup		1.3.6.1.4.1.2272.1.63.1
OBJECT IDENTIFIER

rcIsisGlobalAreaAuthType		1.3.6.1.4.1.2272.1.63.1.1
The authentication type for the area
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), simple(1), hmac-md5(2)

rcIsisGlobalAreaKeyId		1.3.6.1.4.1.2272.1.63.1.2
Authentication key-id for the area. This is required if the auth-type is hmac-md5 else it is not required.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..255

rcIsisGlobalAreaAuthKey		1.3.6.1.4.1.2272.1.63.1.3
Authentication key, this key will be used to authenticate the LSP's received on the area
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..255)

rcIsisGlobalDomainAuthType		1.3.6.1.4.1.2272.1.63.1.4
The authentication type for the domain
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), simple(1), hmac-md5(2)

rcIsisGlobalDomainKeyId		1.3.6.1.4.1.2272.1.63.1.5
The authentication key-id for the domain. This is required if the auth-type is hmac-md5 else it is not required.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..255

rcIsisGlobalDomainAuthKey		1.3.6.1.4.1.2272.1.63.1.6
Authentication key, this key will be used to authenticate the LSP's received on the domain
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..255)

rcIsisGlobalCsnpInt		1.3.6.1.4.1.2272.1.63.1.7
Interval of time, in seconds, between periodic transmission of a complete set of CSNPs on multiaccess networks if this router is the designated router at this level. This object follows the resettingTimer behavior. For ResettingTimer description see the ISIS MIB
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..600

rcIsisGlobalRxmtLspInt		1.3.6.1.4.1.2272.1.63.1.8
Minimum interval, in seconds, between re-transmission of a LSP at this level. This object follows the resettingTimer behavior. For ResettingTimer description see the ISIS MIB
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..300

rcIsisGlobalPSNPInterval		1.3.6.1.4.1.2272.1.63.1.9
Minimum interval in seconds between sending Partial Sequence Number PDUs at this level. This object follows the resettingTimer behavior. For ResettingTimer description see the ISIS MIB
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..120

rcIsisGlobalHostName		1.3.6.1.4.1.2272.1.63.1.10
The hostname listed in LSP, or the system name if host name is not configured.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..255)

rcIsisGlobalSpfDelay		1.3.6.1.4.1.2272.1.63.1.11
ISIS SPF delay in miliseconds
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..5000

rcIsisGlobalControlVlan		1.3.6.1.4.1.2272.1.63.1.12
ISIS control vlan ID
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..4094

rcIsisGlobalIpSourceAddress		1.3.6.1.4.1.2272.1.63.1.13
ISIS PLSB IP address. Define an existing router interface for management (ping/traceroute)
Status: current	Access: read-write
OBJECT-TYPE
	InetAddress

rcIsisGlobalIpSourceAddressType		1.3.6.1.4.1.2272.1.63.1.14
The type of address for existing router interface for management (ping/traceroute)
Status: current	Access: read-write
OBJECT-TYPE
	InetAddressType

rcIsisCircuitTable		1.3.6.1.4.1.2272.1.63.2
Table of IS-IS Circuit, this is extension to the isisCircTable defined in ISIS MIB
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIsisCircuitEntry

rcIsisCircuitEntry		1.3.6.1.4.1.2272.1.63.2.1
An entry of rcIsisCircuit Table. A Entry in table exists for each ISIS circuit created
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIsisCircuitEntry

rcIsisCircuitIndex		1.3.6.1.4.1.2272.1.63.2.1.1
The identifier of this circuit, unique within the Intermediate System. This object follows the index behavior. This is for SNMP Indexing purposes only and need not have any relation to any protocol value.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

rcIsisCircuitType		1.3.6.1.4.1.2272.1.63.2.1.2
ISIS circuit type this is an extention to ISIS circuit table, this was required a standard MIB circuit type does not support passive type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	bcast(1), ptpt(2), passive(3)

rcIsisCircuitAuthType		1.3.6.1.4.1.2272.1.63.2.1.3
Authentication type for IIH to be sent/reveived on the circuit/interface
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), simple(1), hmac-md5(2)

rcIsisCircuitKeyId		1.3.6.1.4.1.2272.1.63.2.1.4
Authentication key id related to IIH key This can be set only if the auth-type is hmac-md5
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..255

rcIsisCircuitAuthKey		1.3.6.1.4.1.2272.1.63.2.1.5
Authentication key to be used to authenticate IIH sent/reveived on the circuit/interface
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..255)

rcIsisCircuitAddr		1.3.6.1.4.1.2272.1.63.2.1.6
IP address associated with the interface
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIsisCircuitMask		1.3.6.1.4.1.2272.1.63.2.1.7
IP mask associated with the interface
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

rcIsisCircuitOperState		1.3.6.1.4.1.2272.1.63.2.1.8
This variable tells the operating state of circ
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(0), up(1), down(2)

rcIsisCircuitNumAdj		1.3.6.1.4.1.2272.1.63.2.1.9
NUmber of adjacencies
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIsisCircuitNumUpAdj		1.3.6.1.4.1.2272.1.63.2.1.10
Number of adjancencies which are UP
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIsisStats		1.3.6.1.4.1.2272.1.63.3
OBJECT IDENTIFIER

rcIsisStatsClearErrorCounters		1.3.6.1.4.1.2272.1.63.3.1
Clear ISIS global and interface error counters.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIsisStatsClearPacketCounters		1.3.6.1.4.1.2272.1.63.3.2
Clear IS-IS control packets sent and received at each level on all the interface/circuits.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcIsisPlsbTable		1.3.6.1.4.1.2272.1.63.4
Table of PLSB under IS-IS
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIsisPlsbEntry

rcIsisPlsbEntry		1.3.6.1.4.1.2272.1.63.4.1
An entry of rcIsisPlsb Table. A Entry in table exists for each plsb instance created
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIsisPlsbEntry

rcIsisPlsbId		1.3.6.1.4.1.2272.1.63.4.1.1
PLSB instance ID
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..100

rcIsisPlsbRowStatus		1.3.6.1.4.1.2272.1.63.4.1.2
The state of the rcIsisPlsbEntry.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcIsisPlsbNodeNickName		1.3.6.1.4.1.2272.1.63.4.1.3
PLSB node's nickname is used to calculate ISID multicast mac address.
Status: current	Access: read-create
OBJECT-TYPE
	IsisPlsbNodeNickName

rcIsisPlsbVlans		1.3.6.1.4.1.2272.1.63.4.1.4
PLSB ISIS vlans for a PLSB instance.
Status: current	Access: read-create
OBJECT-TYPE
	OCTET STRING	Size(512)

rcIsisPlsbLsdbTrap		1.3.6.1.4.1.2272.1.63.4.1.5
isis PLSB lsdb update trap enable on this plsb instance
Status: current	Access: read-create
OBJECT-TYPE
	EnableValue

rcIsisPlsbState		1.3.6.1.4.1.2272.1.63.4.1.6
enable/disable PLSB.
Status: current	Access: read-create
OBJECT-TYPE
	EnableValue

rcIsisPlsbIpShortcut		1.3.6.1.4.1.2272.1.63.4.1.7
ISIS PLSB IP shortcut enabled
Status: current	Access: read-create
OBJECT-TYPE
	EnableValue

rcIsisPlsbPrimaryVlan		1.3.6.1.4.1.2272.1.63.4.1.8
Primary Vlan Id for this plsb instance.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..4094

rcIsisPlsbSmltSplitBEB		1.3.6.1.4.1.2272.1.63.4.1.9
ISIS PLSB SMLT split BEB for this plsb instance.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	primary(1), secondary(2)

rcIsisPlsbSmltBmac		1.3.6.1.4.1.2272.1.63.4.1.10
ISIS PLSB SMLT virtual MAC for this plsb instance.
Status: current	Access: read-create
OBJECT-TYPE
	MacAddress

rcIsisPlsbSmltPeerSysId		1.3.6.1.4.1.2272.1.63.4.1.11
ISIS PLSB SMLT Peer's system-id for this plsb instance.
Status: current	Access: read-create
OBJECT-TYPE
	IsisSystemID

rcIsisCircuitPlsbTable		1.3.6.1.4.1.2272.1.63.5
Table of IS-IS Circuit PLSB instance
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIsisCircuitPlsbEntry

rcIsisCircuitPlsbEntry		1.3.6.1.4.1.2272.1.63.5.1
An entry of rcIsisCircuitPlsb Table. A Entry in table exists for each PLSB instance under a ISIS circuit created
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIsisCircuitPlsbEntry

rcIsisCircuitPlsbIndex		1.3.6.1.4.1.2272.1.63.5.1.1
The identifier of this circuit, unique within the Intermediate System. This object follows the index behavior. This is for SNMP Indexing purposes only and need not have any relation to any protocol value.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

rcIsisCircuitPlsbId		1.3.6.1.4.1.2272.1.63.5.1.2
PLSB instance ID
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..100

rcIsisCircuitPlsbRowStatus		1.3.6.1.4.1.2272.1.63.5.1.3
The state of the rcIsisCircuitPlsbEntry.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcIsisCircuitPlsbState		1.3.6.1.4.1.2272.1.63.5.1.4
PLSB functionality enable on this Plsb instance at this port
Status: current	Access: read-create
OBJECT-TYPE
	EnableValue

rcIsisCircuitPlsbType		1.3.6.1.4.1.2272.1.63.5.1.5
ISIS circuit type this is an extention to ISIS circuit table, this was required a standard MIB circuit type does not support passive type
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	bcast(1), ptpt(2)

rcIsisCircuitPlsbL1Metric		1.3.6.1.4.1.2272.1.63.5.1.6
The metric value of this circuit for this level.
Status: current	Access: read-create
OBJECT-TYPE
	IsisDefaultL1Metric

rcIsisCircuitPlsbWideL1Metric		1.3.6.1.4.1.2272.1.63.5.1.7
The metric value of this circuit for this level.
Status: current	Access: read-create
OBJECT-TYPE
	IsisWideL1Metric

rcIsisPlsbUnicastFibTable		1.3.6.1.4.1.2272.1.63.6
Table of IS-IS PLSB Unicast FIB
Status: obsolete	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIsisPlsbUnicastFibEntry

rcIsisPlsbUnicastFibEntry		1.3.6.1.4.1.2272.1.63.6.1
An entry of rcIsisPlsbUnicastFib Table. A Entry in table exists for each PLSB unicast forwarding entry generated by ISIS SPF computation
Status: obsolete	Access: not-accessible
OBJECT-TYPE
	RcIsisPlsbUnicastFibEntry

rcIsisPlsbUnicastFibDestinationMacAddr		1.3.6.1.4.1.2272.1.63.6.1.1
Destination Mac Address of the unicast FIB entry
Status: obsolete	Access: not-accessible
OBJECT-TYPE
	MacAddress

rcIsisPlsbUnicastFibVlan		1.3.6.1.4.1.2272.1.63.6.1.2
Vlan of the unicast FIB entry
Status: obsolete	Access: not-accessible
OBJECT-TYPE
	Integer32	1..4094

rcIsisPlsbUnicastFibSysId		1.3.6.1.4.1.2272.1.63.6.1.3
System ID of the node where unicast FIB entry come from
Status: obsolete	Access: not-accessible
OBJECT-TYPE
	OCTET STRING	Size(6)

rcIsisPlsbUnicastFibOutgoingPort		1.3.6.1.4.1.2272.1.63.6.1.4
Outgoing port of the unicast Fib entry.
Status: obsolete	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcIsisPlsbMulticastFibTable		1.3.6.1.4.1.2272.1.63.7
Table of IS-IS PLSB Multicast FIB
Status: obsolete	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIsisPlsbMulticastFibEntry

rcIsisPlsbMulticastFibEntry		1.3.6.1.4.1.2272.1.63.7.1
An entry of rcIsisPlsbmulticastFib Table. A Entry in table exists for each PLSB Multicast forwarding entry generated by ISIS SPF computation
Status: obsolete	Access: not-accessible
OBJECT-TYPE
	RcIsisPlsbMulticastFibEntry

rcIsisPlsbMulticastFibMcastDestMacAddr		1.3.6.1.4.1.2272.1.63.7.1.1
Multicast destination Mac Address of the multicast FIB entry
Status: obsolete	Access: not-accessible
OBJECT-TYPE
	MacAddress

rcIsisPlsbMulticastFibVlan		1.3.6.1.4.1.2272.1.63.7.1.2
Vlan of the multicast FIB entry
Status: obsolete	Access: not-accessible
OBJECT-TYPE
	Integer32	1..4094

rcIsisPlsbMulticastFibSysId		1.3.6.1.4.1.2272.1.63.7.1.3
System ID of the node where multicast FIB entry come from
Status: obsolete	Access: not-accessible
OBJECT-TYPE
	OCTET STRING	Size(6)

rcIsisPlsbMulticastFibIsid		1.3.6.1.4.1.2272.1.63.7.1.4
Isid id of the multicast FIB entry
Status: obsolete	Access: read-only
OBJECT-TYPE
	Integer32	1..16777215

rcIsisPlsbMulticastFibOutgoingPorts		1.3.6.1.4.1.2272.1.63.7.1.5
Nni port of the multicast Fib entry.
Status: obsolete	Access: read-only
OBJECT-TYPE
	DisplayString

rcIsisPlsbIsidTable		1.3.6.1.4.1.2272.1.63.8
Table of IS-IS PLSB ISID
Status: obsolete	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIsisPlsbIsidEntry

rcIsisPlsbIsidEntry		1.3.6.1.4.1.2272.1.63.8.1
An entry of rcIsisPlsbIsid Table. A Entry in table exists for each PLSB i-sid configed or discovered by IS-IS
Status: obsolete	Access: not-accessible
OBJECT-TYPE
	RcIsisPlsbIsidEntry

rcIsisPlsbIsidSourceName		1.3.6.1.4.1.2272.1.63.8.1.1
nick name of node where this i-sid got configed or discovered
Status: obsolete	Access: not-accessible
OBJECT-TYPE
	Integer32	1..16777215

rcIsisPlsbIsidId		1.3.6.1.4.1.2272.1.63.8.1.2
IS-IS PLSB Isid id
Status: obsolete	Access: not-accessible
OBJECT-TYPE
	Integer32	1..16777215

rcIsisPlsbIsidSysId		1.3.6.1.4.1.2272.1.63.8.1.3
System ID of the node where multicast FIB entry come from
Status: obsolete	Access: not-accessible
OBJECT-TYPE
	OCTET STRING	Size(6)

rcIsisPlsbIsidType		1.3.6.1.4.1.2272.1.63.8.1.4
PLSB i-sid type
Status: obsolete	Access: read-only
OBJECT-TYPE
	INTEGER	config(1), discover(2)

rcIsisTrap		1.3.6.1.4.1.2272.1.63.9
OBJECT IDENTIFIER

rcIsisLocalLspId		1.3.6.1.4.1.2272.1.63.9.1
The 8 byte Local LSP ID, consisting of the SystemID, Circuit ID, and Fragment Number.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(17)

rcIsisLocall1Metric		1.3.6.1.4.1.2272.1.63.9.2
l1-metric for ISIS interface on local Node.
Status: current	Access: read-only
OBJECT-TYPE
	IsisDefaultL1Metric

rcIsisNgbLspId		1.3.6.1.4.1.2272.1.63.9.3
The 8 byte neighbor LSP ID, consisting of the SystemID, Circuit ID, and Fragment Number.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(17)

rcIsisNgbl1Metric		1.3.6.1.4.1.2272.1.63.9.4
l1-metric for ISIS interface on neighbor Node.
Status: current	Access: read-only
OBJECT-TYPE
	IsisDefaultL1Metric

rcIsisPlsbTrapType		1.3.6.1.4.1.2272.1.63.9.5
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	metricMismatch(1), duplicateSysid(2), lsdbUpdate(3), duplicateNickname(4), bvidMismatch(5), smltVirtBmacMismatch(6), smltPeerBmacMismatch(7), adjState(8), smltSplitBebMismatch(9), multiLinkAdj(10)

rcIsisLocalSysId		1.3.6.1.4.1.2272.1.63.9.6
ISIS local node system-id.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(14)

rcIsisLocalInterface		1.3.6.1.4.1.2272.1.63.9.7
ISIS local interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIsisTrapIndicator		1.3.6.1.4.1.2272.1.63.9.8
indicates that an alarm has been Raised, or an alarm has been cleared.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	alarm(1), clear(2)

rcIsisLocalNickname		1.3.6.1.4.1.2272.1.63.9.9
ISIS local node nick-name.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(7)

rcIsisNgbNickname		1.3.6.1.4.1.2272.1.63.9.10
ISIS neighbor node nick-name.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(7)

rcIsisNgbSysId		1.3.6.1.4.1.2272.1.63.9.11
ISIS neighbor node system-id.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(14)

rcIsisLocalPrimaryBvid		1.3.6.1.4.1.2272.1.63.9.12
ISIS local primary B-VID.
Status: current	Access: read-only
OBJECT-TYPE
	IsisPlsbBvid

rcIsisLocalPrimaryTieBrkAlg		1.3.6.1.4.1.2272.1.63.9.13
The tie breaking algorithm applied to local primary B-VID.
Status: current	Access: read-only
OBJECT-TYPE
	IsisPlsbBvidTieBrkAlg

rcIsisLocalSecondaryBvid		1.3.6.1.4.1.2272.1.63.9.14
ISIS local secondary B-VID.
Status: current	Access: read-only
OBJECT-TYPE
	IsisPlsbBvid

rcIsisLocalSecondaryTieBrkAlg		1.3.6.1.4.1.2272.1.63.9.15
The tie breaking algorithm applied to local seconday B-VID.
Status: current	Access: read-only
OBJECT-TYPE
	IsisPlsbBvidTieBrkAlg

rcIsisNgbPrimaryBvid		1.3.6.1.4.1.2272.1.63.9.16
ISIS neighbor primary B-VID.
Status: current	Access: read-only
OBJECT-TYPE
	IsisPlsbBvid

rcIsisNgbPrimaryTieBrkAlg		1.3.6.1.4.1.2272.1.63.9.17
The neighbor tie breaking algorithm applied to primary B-VID.
Status: current	Access: read-only
OBJECT-TYPE
	IsisPlsbBvidTieBrkAlg

rcIsisNgbSecondaryBvid		1.3.6.1.4.1.2272.1.63.9.18
ISIS neighbor secondary B-VID.
Status: current	Access: read-only
OBJECT-TYPE
	IsisPlsbBvid

rcIsisNgbSecondaryTieBrkAlg		1.3.6.1.4.1.2272.1.63.9.19
The neighbor tie breaking algorithm applied to secondary B-VID.
Status: current	Access: read-only
OBJECT-TYPE
	IsisPlsbBvidTieBrkAlg

rcIsisLocalVirtualBmac		1.3.6.1.4.1.2272.1.63.9.20
The SMLT Virtual BMAC configured in the local IST switch.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rcIsisPeerVirtualBmac		1.3.6.1.4.1.2272.1.63.9.21
The SMLT Virtual BMAC configured in the IST Peer.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rcIsisSysId		1.3.6.1.4.1.2272.1.63.9.22
The isis system id configured in the local switch or IST peer.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(14)

rcIsisSmltPeerSysId		1.3.6.1.4.1.2272.1.63.9.23
The SMLT Peer system-id configured in the local switch or IST Peer.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(14)

rcIsisAdjState		1.3.6.1.4.1.2272.1.63.9.24
indicate different ISIS adjacency states.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	init(2), up(3), down(4)

rcIsisDuplicateNnameCounter		1.3.6.1.4.1.2272.1.63.9.25
indicate how many nodes in the network share the nick-name.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

rcIsisLocalBvidCounter		1.3.6.1.4.1.2272.1.63.9.26
indicate how many b-vid configured on local nodes.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

rcIsisNgbBvidCounter		1.3.6.1.4.1.2272.1.63.9.27
indicate how many b-vid configured on a neighbor nodes.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

rcIsisLocalSmltSplitBeb		1.3.6.1.4.1.2272.1.63.9.28
The SMLT Split-BEB configured in the local IST switch.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	primary(1), secondary(2)

rcIsisPeerSmltSplitBeb		1.3.6.1.4.1.2272.1.63.9.29
The SMLT Split-BEB configured in the IST Peer switch.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	primary(1), secondary(2)

rcIsisLocalHostName		1.3.6.1.4.1.2272.1.63.9.30
ISIS local host name.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..255)

rcIsisNgbHostName		1.3.6.1.4.1.2272.1.63.9.31
ISIS neighbor host name.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..255)

rcIsisPrevInterface		1.3.6.1.4.1.2272.1.63.9.32
ISIS local interface index for previously found adj.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIsisAdjTable		1.3.6.1.4.1.2272.1.63.10
Table of IS-IS Adjacency, this is extension to the isisISAdjTable defined in ISIS MIB
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIsisAdjEntry

rcIsisAdjEntry		1.3.6.1.4.1.2272.1.63.10.1
An entry of rcIsisAdj Table. A Entry in table exists for each ISIS adjacency
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIsisAdjEntry

rcIsisAdjCircIndex		1.3.6.1.4.1.2272.1.63.10.1.1
The identifier of this circuit, unique within the Intermediate System. This object follows the index behavior. This is for SNMP Indexing purposes only and need not have any relation to any protocol value.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

rcIsisAdjIndex		1.3.6.1.4.1.2272.1.63.10.1.2
A unique value identifying the IS adjacency from all other such adjacencies on this circuit. This value is automatically assigned by the system when the adjacency is created.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..2147483647

rcIsisAdjHostName		1.3.6.1.4.1.2272.1.63.10.1.3
The hostname listed in LSP, or the system name if host name is not configured.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..255)

rcIsisAdjIfIndex		1.3.6.1.4.1.2272.1.63.10.1.4
The value of ifIndex for the interface to which this circuit corresponds.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcIsisLSPTable		1.3.6.1.4.1.2272.1.63.11
Table of IS-IS LSP, this is extension to the isisLSPSummaryTable defined in ISIS MIB
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIsisLSPEntry

rcIsisLSPEntry		1.3.6.1.4.1.2272.1.63.11.1
An entry of rcIsisLSP Table. A Entry in table exists for each ISIS LSP
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIsisLSPEntry

rcIsisLSPLevel		1.3.6.1.4.1.2272.1.63.11.1.1
At which level does this LSP appear?
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	area(1), domain(2)

rcIsisLSPID		1.3.6.1.4.1.2272.1.63.11.1.2
The 8 byte LSP ID, consisting of the SystemID, Circuit ID, and Fragment Number.
Status: current	Access: not-accessible
OBJECT-TYPE
	OCTET STRING	Size(8)

rcIsisLSPSeq		1.3.6.1.4.1.2272.1.63.11.1.3
The sequence number for this LSP.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcIsisLSPHostName		1.3.6.1.4.1.2272.1.63.11.1.4
The hostname listed in LSP, or the system name if host name is not configured.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..255)

rcIsisLSPNickName		1.3.6.1.4.1.2272.1.63.11.1.5
PLSB node's nickname
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..16777215

rcIsisLSPLifetimeRemain		1.3.6.1.4.1.2272.1.63.11.1.6
The remaining lifetime in seconds for this LSP.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rcIsisPlsbIpUnicastFibTable		1.3.6.1.4.1.2272.1.63.12
Table of IS-IS PLSB IP Unicast FIB
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIsisPlsbIpUnicastFibEntry

rcIsisPlsbIpUnicastFibEntry		1.3.6.1.4.1.2272.1.63.12.1
An entry of rcIsisPlsbIpUnicastFib Table. A Entry in table exists for each PLSB IP unicast forwarding entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIsisPlsbIpUnicastFibEntry

rcIsisPlsbIpUnicastFibVrfId		1.3.6.1.4.1.2272.1.63.12.1.1
VRF ID of the IP unicast FIB entry, 0 indicates NRE.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

rcIsisPlsbIpUnicastFibDestinationIpAddrType		1.3.6.1.4.1.2272.1.63.12.1.2
The address type of destination IP Address.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddressType

rcIsisPlsbIpUnicastFibDestinationIpAddr		1.3.6.1.4.1.2272.1.63.12.1.3
Destination IP Address of the IP unicast FIB entry. Support ipv4 size(4) and ipv6 size(16)
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddress	Size(4|16)

rcIsisPlsbIpUnicastFibDestinationMask		1.3.6.1.4.1.2272.1.63.12.1.4
Destination IP mask of the IP unicast FIB entry
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddressPrefixLength

rcIsisPlsbIpUnicastFibNextHopBmac		1.3.6.1.4.1.2272.1.63.12.1.5
the nexthop BMAC of the IP unicast FIB entry
Status: current	Access: not-accessible
OBJECT-TYPE
	MacAddress

rcIsisPlsbIpUnicastFibVlan		1.3.6.1.4.1.2272.1.63.12.1.6
Vlan of the IP unicast FIB entry
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..4094

rcIsisPlsbIpUnicastFibIsid		1.3.6.1.4.1.2272.1.63.12.1.7
ISID of the IP unicast FIB entry
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIsisPlsbIpUnicastFibNextHopName		1.3.6.1.4.1.2272.1.63.12.1.8
the nexthop hostname of the IP unicast FIB entry
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

rcIsisPlsbIpUnicastFibOutgoingPort		1.3.6.1.4.1.2272.1.63.12.1.9
Outgoing port of the IP unicast Fib entry.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcIsisPlsbIpUnicastFibPrefixCost		1.3.6.1.4.1.2272.1.63.12.1.10
prefix cost of the IP unicast FIB entry
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcIsisPlsbIpUnicastFibSpbmCost		1.3.6.1.4.1.2272.1.63.12.1.11
bmac cost of the IP unicast FIB entry
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcIsisPlsbUcastFibTable		1.3.6.1.4.1.2272.1.63.13
Table of IS-IS PLSB Unicast FIB
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIsisPlsbUcastFibEntry

rcIsisPlsbUcastFibEntry		1.3.6.1.4.1.2272.1.63.13.1
An entry of rcIsisPlsbUcastFib Table. A Entry in table exists for each PLSB unicast forwarding entry generated by ISIS SPF computation
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIsisPlsbUcastFibEntry

rcIsisPlsbUcastFibSysId		1.3.6.1.4.1.2272.1.63.13.1.1
System ID of the node where unicast FIB entry come from
Status: current	Access: not-accessible
OBJECT-TYPE
	OCTET STRING	Size(6)

rcIsisPlsbUcastFibVlan		1.3.6.1.4.1.2272.1.63.13.1.2
Vlan of the unicast FIB entry
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..4094

rcIsisPlsbUcastFibDestinationMacAddr		1.3.6.1.4.1.2272.1.63.13.1.3
Destination Mac Address of the unicast FIB entry
Status: current	Access: not-accessible
OBJECT-TYPE
	MacAddress

rcIsisPlsbUcastFibOutgoingPort		1.3.6.1.4.1.2272.1.63.13.1.4
Outgoing port of the unicast Fib entry.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcIsisPlsbUcastFibHostName		1.3.6.1.4.1.2272.1.63.13.1.5
Host name of the node where unicast FIB entry come from
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..255)

rcIsisPlsbUcastFibCost		1.3.6.1.4.1.2272.1.63.13.1.6
unicast FIB cost
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcIsisPlsbMcastFibTable		1.3.6.1.4.1.2272.1.63.14
Table of IS-IS PLSB Multicast FIB
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIsisPlsbMcastFibEntry

rcIsisPlsbMcastFibEntry		1.3.6.1.4.1.2272.1.63.14.1
An entry of rcIsisPlsbMcastFib Table. A Entry in table exists for each PLSB Multicast forwarding entry generated by ISIS SPF computation
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIsisPlsbMcastFibEntry

rcIsisPlsbMcastFibSysId		1.3.6.1.4.1.2272.1.63.14.1.1
System ID of the node where multicast FIB entry come from
Status: current	Access: not-accessible
OBJECT-TYPE
	OCTET STRING	Size(6)

rcIsisPlsbMcastFibVlan		1.3.6.1.4.1.2272.1.63.14.1.2
Vlan of the multicast FIB entry
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..4094

rcIsisPlsbMcastFibMcastDestMacAddr		1.3.6.1.4.1.2272.1.63.14.1.3
Multicast destination Mac Address of the multicast FIB entry
Status: current	Access: not-accessible
OBJECT-TYPE
	MacAddress

rcIsisPlsbMcastFibIsid		1.3.6.1.4.1.2272.1.63.14.1.4
Isid id of the multicast FIB entry
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..16777215

rcIsisPlsbMcastFibNickName		1.3.6.1.4.1.2272.1.63.14.1.5
nick name of node where this i-sid got configured or discovered
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..16777215

rcIsisPlsbMcastFibType		1.3.6.1.4.1.2272.1.63.14.1.6
PLSB i-sid type
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	config(1), discover(2)

rcIsisPlsbMcastFibOutgoingPorts		1.3.6.1.4.1.2272.1.63.14.1.7
Nni port of the multicast Fib entry.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

rcIsisPlsbMcastFibHostName		1.3.6.1.4.1.2272.1.63.14.1.8
Host name of the node where multicast FIB entry come from
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..255)

rcIsisPlsbNodeTable		1.3.6.1.4.1.2272.1.63.15
Table of IS-IS PLSB Node
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIsisPlsbNodeEntry

rcIsisPlsbNodeEntry		1.3.6.1.4.1.2272.1.63.15.1
An entry of rcIsisPlsbNode Table. A Entry in table exists for each node running PLSB ISIS in the setup.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIsisPlsbNodeEntry

rcIsisPlsbNodeSysId		1.3.6.1.4.1.2272.1.63.15.1.1
System ID of the PLSB node entry
Status: current	Access: not-accessible
OBJECT-TYPE
	OCTET STRING	Size(6)

rcIsisPlsbNodePrimaryParentSysId		1.3.6.1.4.1.2272.1.63.15.1.2
System ID of parent node of the PLSB node entry for primary bvlan
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(6)

rcIsisPlsbNodePrimaryBvlan		1.3.6.1.4.1.2272.1.63.15.1.3
spbm primary b-vlan
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..4094

rcIsisPlsbNodeSecondaryParentSysId		1.3.6.1.4.1.2272.1.63.15.1.4
System ID of parent node of the PLSB node entry for secondary bvlan
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(6)

rcIsisPlsbNodeSecondaryBvlan		1.3.6.1.4.1.2272.1.63.15.1.5
spbm secondary b-vlan
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..4094

rcIsisSpbmPortDropStatsTable		1.3.6.1.4.1.2272.1.63.16
Table of IS-IS SPBM port drop-stats by port index and SPBM b-vlan
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcIsisSpbmPortDropStatsEntry

rcIsisSpbmPortDropStatsEntry		1.3.6.1.4.1.2272.1.63.16.1
SPBM port based frame drop counters.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcIsisSpbmPortDropStatsEntry

rcIsisSpbmPortDropStatsPortIndex		1.3.6.1.4.1.2272.1.63.16.1.1
An index value that uniquely identifies a port. This value is similar to ifIndex in MIB2.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

rcIsisSpbmPortDropStatsVlanId		1.3.6.1.4.1.2272.1.63.16.1.2
A value that uniquely identifies the SPBM Virtual LAN associated with this entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..4094

rcIsisSpbmPortDropStatsVlanType		1.3.6.1.4.1.2272.1.63.16.1.3
Indicates the type of SPBM bvlan
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	primary(1), secondary(2)

rcIsisSpbmPortDropStatsUnknownUcastSrcAddr		1.3.6.1.4.1.2272.1.63.16.1.4
The total number of SPBM unknown unicast SA packets dropped on SPBM bvlan.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcIsisSpbmPortDropStatsRpfcUcastSrcAddr		1.3.6.1.4.1.2272.1.63.16.1.5
The total number of SPBM reverse path forwarding check (RPFC) unicast SA packets dropped on SPBM bvlan.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcIsisSpbmPortDropStatsUnknownUcastDestAddr		1.3.6.1.4.1.2272.1.63.16.1.6
The total number of SPBM unknown unicast DA packets dropped on SPBM bvlan.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcIsisSpbmPortDropStatsUnknownMcastDestAddr		1.3.6.1.4.1.2272.1.63.16.1.7
The total number of SPBM unknown multicast DA packets dropped on SPBM bvlan.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcIsisSpbmPortDropStatsRpfcMcastSrcAddr		1.3.6.1.4.1.2272.1.63.16.1.8
The total number of SPBM reverse path forwarding check (RPFC) multicast SA packets dropped on SPBM bvlan.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

rcIsisSpbmPortDropStatsLastDropMac		1.3.6.1.4.1.2272.1.63.16.1.9
The DA or SA last dropped on SPBM bvlan.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rcIsisSpbmPortDropStatsIsMacDestAddr		1.3.6.1.4.1.2272.1.63.16.1.10
The last dropped mac on SPBM bvlan is DA or not.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcIsisSpbmPortDropStatsLastDropMacHostName		1.3.6.1.4.1.2272.1.63.16.1.11
The host name of the nodes where last dropped SA or DA on SPBM bvlan belongs
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..255)

rcPlsbGlobal		1.3.6.1.4.1.2272.1.78.1
OBJECT IDENTIFIER

rcPlsbGlobalVlans		1.3.6.1.4.1.2272.1.78.1.1
PLSB vlan entry.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(512)

rcPlsbGlobalEnable		1.3.6.1.4.1.2272.1.78.1.2
Enable/Disable PLSB global flag.
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcPlsbGlobalMsti		1.3.6.1.4.1.2272.1.78.1.3
MSTI instance ID for PLSB VLANS
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..63

rcPlsbGlobalEtherType		1.3.6.1.4.1.2272.1.78.1.4
SPBM Ethertype
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..FFFF

rcCfmMaintenanceDomainTable		1.3.6.1.4.1.2272.1.69.1
Connectivity Fault Management Maintenance Domain table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcCfmMaintenanceDomainEntry

rcCfmMaintenanceDomainEntry		1.3.6.1.4.1.2272.1.69.1.1
Connectivity Fault Management Maintenance Domain entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcCfmMaintenanceDomainEntry

rcCfmMaintenanceDomainIndex		1.3.6.1.4.1.2272.1.69.1.1.1
Maintenance Domain index
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..2147483647

rcCfmMaintenanceDomainName		1.3.6.1.4.1.2272.1.69.1.1.2
Maintenance Domain Name
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(1..22)

rcCfmMaintenanceDomainRowStatus		1.3.6.1.4.1.2272.1.69.1.1.3
Used to create/delete entries
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcCfmMaintenanceDomainNumOfMa		1.3.6.1.4.1.2272.1.69.1.1.4
Used to indicate the number of MAs belong to this maintenance domain
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcCfmMaintenanceDomainLevel		1.3.6.1.4.1.2272.1.69.1.1.6
To set the maintenance level in this domain
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..7

rcCfmMaintenanceDomainNumOfMip		1.3.6.1.4.1.2272.1.69.1.1.7
Used to indicate the number of Mips belong to this maintenance domain
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcCfmMaintenanceDomainType		1.3.6.1.4.1.2272.1.69.1.1.8
To indicate the type of domain
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(0), trunk(1), sg(2), endpt(3), vlan(4), port(5), mimencapvlan(6), nodal(7)

rcCfmMaintenanceAssociationTable		1.3.6.1.4.1.2272.1.69.2
Connectivity Fault Management Maintenance Association table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcCfmMaintenanceAssociationEntry

rcCfmMaintenanceAssociationEntry		1.3.6.1.4.1.2272.1.69.2.1
Connectivity Fault Management Maintenance Association entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcCfmMaintenanceAssociationEntry

rcCfmMaintenanceAssociationDomainIndex		1.3.6.1.4.1.2272.1.69.2.1.1
Maintenance Association Domain Index
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..2147483647

rcCfmMaintenanceAssociationAssociationIndex		1.3.6.1.4.1.2272.1.69.2.1.2
Maintenance Association Index
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..2147483647

rcCfmMaintenanceAssociationDomainName		1.3.6.1.4.1.2272.1.69.2.1.3
Maintenance Association Domain Name
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..22)

rcCfmMaintenanceAssociationAssociationName		1.3.6.1.4.1.2272.1.69.2.1.4
Maintenance Association Name
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(1..22)

rcCfmMaintenanceAssociationAdminState		1.3.6.1.4.1.2272.1.69.2.1.5
Administratively enable or disable a maintenance association.
Status: current	Access: read-create
OBJECT-TYPE
	EnableValue

rcCfmMaintenanceAssociationRowStatus		1.3.6.1.4.1.2272.1.69.2.1.6
Used to create/delete entries
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcCfmMaintenanceAssociationNumOfMep		1.3.6.1.4.1.2272.1.69.2.1.12
Used to indicate the number of MEPs belong to this maintenance association
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcCfmMaintenanceEndPointTable		1.3.6.1.4.1.2272.1.69.3
Connectivity Fault Management Maintenance Association table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcCfmMaintenanceEndPointEntry

rcCfmMaintenanceEndPointEntry		1.3.6.1.4.1.2272.1.69.3.1
Connectivity Fault Management Maintenance EndPoint entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcCfmMaintenanceEndPointEntry

rcCfmMaintenanceEndPointDomainIndex		1.3.6.1.4.1.2272.1.69.3.1.1
Maintenance Domain Name
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..2147483647

rcCfmMaintenanceEndPointAssociationIndex		1.3.6.1.4.1.2272.1.69.3.1.2
Maintenance Association Name
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..2147483647

rcCfmMaintenanceEndPointId		1.3.6.1.4.1.2272.1.69.3.1.3
Maintenance EndPoint ID
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..8191

rcCfmMaintenanceEndPointDomainName		1.3.6.1.4.1.2272.1.69.3.1.4
Maintenance Domain Name
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..22)

rcCfmMaintenanceEndPointAssociationName		1.3.6.1.4.1.2272.1.69.3.1.5
Maintenance Association Name
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..22)

rcCfmMaintenanceEndPointAdminState		1.3.6.1.4.1.2272.1.69.3.1.6
Administratively enable or disable a maintenance EndPoint.
Status: current	Access: read-create
OBJECT-TYPE
	EnableValue

rcCfmMaintenanceEndPointRowStatus		1.3.6.1.4.1.2272.1.69.3.1.7
Used to create/delete entries
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcCfmMaintenanceEndPointMepType		1.3.6.1.4.1.2272.1.69.3.1.11
Mep Type
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	trunk(1), sg(2), endpt(4), unused(8), vlan(16), port(32), endptClient(64), nodal(3145728), remotetrunk(32769), remotesg(32770), remoteendpt(32772), remoteVlan(32784), remotePort(32800), remoteEndptClient(32832)

rcCfmMaintenanceEndPointServiceDescription		1.3.6.1.4.1.2272.1.69.3.1.13
Used to specify what service this mep assigned to
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..48)

rcCfmMaintenanceEndPointMepStatus		1.3.6.1.4.1.2272.1.69.3.1.15
Indicating if the mep status is active or inactive. Only Dual-Home Ring endpoint client meps can have active/inactive status. All other mep types have active status.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	active(1), inactive(2)

rcCfmGlobals		1.3.6.1.4.1.2272.1.69.10
OBJECT IDENTIFIER

rcCfmGlobalsEtherType		1.3.6.1.4.1.2272.1.69.10.1
CFM Ether Type
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..FFFF

rcCfmGlobalsSpbmAdminState		1.3.6.1.4.1.2272.1.69.10.8
Enable/Disable global cfm support for SPBM VLANs
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcCfmGlobalsSpbmLevel		1.3.6.1.4.1.2272.1.69.10.9
Used to set the global cfm maintenance level for SPBM VLANs
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..7

rcCfmGlobalsSpbmMepId		1.3.6.1.4.1.2272.1.69.10.10
Set the global cfm Maintenance End Point ID value for SPBM VLANs
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..8191

rcCfmGlobalsCmacAdminState		1.3.6.1.4.1.2272.1.69.10.11
Enable/Disable global cfm support for C-VLANs
Status: current	Access: read-write
OBJECT-TYPE
	EnableValue

rcCfmGlobalsCmacLevel		1.3.6.1.4.1.2272.1.69.10.12
Used to set the global cfm maintenance level for C-VLANs
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..7

rcCfmGlobalsCmacMepId		1.3.6.1.4.1.2272.1.69.10.13
Set the global cfm Maintenance End Point ID value for C-VLANs
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..8191

rcCfmTransmitLbmTable		1.3.6.1.4.1.2272.1.69.17
Connectivity Fault Management transmit LBM table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcCfmTransmitLbmEntry

rcCfmTransmitLbmEntry		1.3.6.1.4.1.2272.1.69.17.1
Connectivity Fault Management Maintenance EndPoint LBM entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcCfmTransmitLbmEntry

rcCfmTransmitLbmDomainIndex		1.3.6.1.4.1.2272.1.69.17.1.1
Maintenance Domain Name
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..2147483647

rcCfmTransmitLbmAssociationIndex		1.3.6.1.4.1.2272.1.69.17.1.2
Maintenance Association Name
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..2147483647

rcCfmTransmitLbmIndex		1.3.6.1.4.1.2272.1.69.17.1.3
Maintenance EndPoint Index
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..8191

rcCfmTransmitLbmDomainName		1.3.6.1.4.1.2272.1.69.17.1.4
Maintenance Domain Name
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..22)

rcCfmTransmitLbmAssociationName		1.3.6.1.4.1.2272.1.69.17.1.5
Maintenance Association Name
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..22)

rcCfmTransmitLbmDestMacAddress		1.3.6.1.4.1.2272.1.69.17.1.6
An indication of the target MAC Address Field to be transmitted, either: A unicast destination MAC address.
Status: current	Access: read-write
OBJECT-TYPE
	MacAddress

rcCfmTransmitLbmDestMepId		1.3.6.1.4.1.2272.1.69.17.1.7
An indication of the target MAC Address Field to be transmitted, either: The Maintenance Assiciation End Point identifier of another MEP in the same Maintenance Association
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..8191

rcCfmTransmitLbmDestIsMepId		1.3.6.1.4.1.2272.1.69.17.1.8
True indicates that MepId of the target MEP is used for Loopback transmission. False indicates that unicast destination MAC address of the target MEP is used for Loopback transmission.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcCfmTransmitLbmMessages		1.3.6.1.4.1.2272.1.69.17.1.9
The number of loopback messages to be transmitted.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..10000

rcCfmTransmitLbmVlanPriority		1.3.6.1.4.1.2272.1.69.17.1.11
Priority. 3 bit value to be used in the VLAN tsg, if present in the transmitted frame.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..7

rcCfmTransmitLbmVlanDropEnable		1.3.6.1.4.1.2272.1.69.17.1.12
Drop Enable bit value to be used in the VLAN tag, if present in the transmitted frame.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcCfmTransmitLbmSeqNumber		1.3.6.1.4.1.2272.1.69.17.1.13
The transaction identifier/sequence number of the first loopback message (to be) sent.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcCfmTransmitLbmResultOk		1.3.6.1.4.1.2272.1.69.17.1.14
Indicates the result of the operation: -true. The Loopback Message(s) will be (or have been) sent. -false. The Loopback Message(s) will not be sent.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcCfmTransmitLbmStatus		1.3.6.1.4.1.2272.1.69.17.1.15
Status of the transmit loopback service: -ready. The service is available. -transmit. The service is transmitting, or about to transmit, the Loopback messages. -abort The service is aborted or about to abort the Loopback messages. This column will also be used to avoid concurrency or race condition problems that could occur if two or more management entities try to use the service at the same time.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ready(1), transmit(2), abort(3)

rcCfmTransmitLbmResult		1.3.6.1.4.1.2272.1.69.17.1.16
Display the LBM result.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..799)

rcCfmTransmitLbmTimeoutInt		1.3.6.1.4.1.2272.1.69.17.1.18
The interval to wait for an LBM time-out with a range of (1..10) seconds with a default value of 3 seconds.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..10

rcCfmTransmitLbmInterFrameInt		1.3.6.1.4.1.2272.1.69.17.1.19
The interval between LBM frames with a range of (0..1000) msecs with a default value of 500 msecs. The value of 0 msecs indicates to send the frames as fast as possible.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..1000

rcCfmTransmitLbmTestPattern		1.3.6.1.4.1.2272.1.69.17.1.20
The test pattern to use in the LBM PDU with range of values namely allZero, allZeroCrc, pseudoRandomBitSequence and pseudoRandomBitSequenceCrc and with a default value of allZero. value meaning -------- ------- allZero(1) Null signal without CRC-32 allZeroCrc(2) Null signal with CRC-32 pseudoRandomBitSequence(3) PRBS 1/2^31-1 without CRC-32 pseudoRandomBitSequenceCrc(4) PBRS 1/2^31-1 with CRC-32
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	allZero(1), allZeroCrc(2), pseudoRandomBitSequence(3), pseudoRandomBitSequenceCrc(4)

rcCfmTransmitLbmDataSize		1.3.6.1.4.1.2272.1.69.17.1.21
An arbitrary amount of data to be included in the data TLV, if the Data Size is selected to be sent.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..400

rcCfmTransmitLbmFrameSize		1.3.6.1.4.1.2272.1.69.17.1.22
If the frame size is specified then the data size shall be internally calculated and the calculated data size shall be included in the data TLV.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..9600

rcCfmTransmitLbmSourceMode		1.3.6.1.4.1.2272.1.69.17.1.23
Source modes of the transmit loopback service.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nodal(1), smltVirtual(2), noVlanMac(3)

rcCfmTransmitLtmTable		1.3.6.1.4.1.2272.1.69.18
Connectivity Fault Management transmit LTM table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcCfmTransmitLtmEntry

rcCfmTransmitLtmEntry		1.3.6.1.4.1.2272.1.69.18.1
Connectivity Fault Management Maintenance EndPoint LTM entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcCfmTransmitLtmEntry

rcCfmTransmitLtmDomainIndex		1.3.6.1.4.1.2272.1.69.18.1.1
Maintenance Domain Name
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..2147483647

rcCfmTransmitLtmAssociationIndex		1.3.6.1.4.1.2272.1.69.18.1.2
Maintenance Association Name
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..2147483647

rcCfmTransmitLtmIndex		1.3.6.1.4.1.2272.1.69.18.1.3
Maintenance EndPoint Index
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..8191

rcCfmTransmitLtmDomainName		1.3.6.1.4.1.2272.1.69.18.1.4
Maintenance Domain Name
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..22)

rcCfmTransmitLtmAssociationName		1.3.6.1.4.1.2272.1.69.18.1.5
Maintenance Association Name
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..22)

rcCfmTransmitLtmVlanPriority		1.3.6.1.4.1.2272.1.69.18.1.6
Priority. 3 bit value to be used in the VLAN tag, if present in the transmitted frame.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..7

rcCfmTransmitLtmDestMacAddress		1.3.6.1.4.1.2272.1.69.18.1.7
An indication of the target MAC Address Field to be transmitted, either: A unicast destination MAC address.
Status: current	Access: read-write
OBJECT-TYPE
	MacAddress

rcCfmTransmitLtmDestMepId		1.3.6.1.4.1.2272.1.69.18.1.8
An indication of the target MAC Address Field to be transmitted, either: The Maintenance Assiciation End Point identifier of another MEP in the same Maintenance Association
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..8191

rcCfmTransmitLtmDestIsMepId		1.3.6.1.4.1.2272.1.69.18.1.9
True indicates that MepId of the target MEP is used for Loopback transmission. False indicates that unicast destination MAC address of the target MEP is used for Loopback transmission.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcCfmTransmitLtmTtl		1.3.6.1.4.1.2272.1.69.18.1.10
The number of hops remaining to this LTM. Decremented by 1 by each Bridge that handles the LTM. The decremented value is returned in the LTR. If 0 on output, the LTM is not transmitted to the next hop. The value of the TTL Field in the LTM transmitted by the originating MEP is controlled by a Managed Object; The default value if none is specified is 64.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..255

rcCfmTransmitLtmSeqNumber		1.3.6.1.4.1.2272.1.69.18.1.11
The transaction identifier/sequence number of the first loopback message (to be) sent.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcCfmTransmitLtmResultOk		1.3.6.1.4.1.2272.1.69.18.1.12
Indicates the result of the operation: -true. The Loopback Message(s) will be (or have been) sent. -false. The Loopback Message(s) will not be sent.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcCfmTransmitLtmStatus		1.3.6.1.4.1.2272.1.69.18.1.13
Status of the transmit loopback service: -ready. The service is available. -transmit. The service is transmitting, or about to transmit, the Loopback messages. -abort. The service is aborted, or about to abort the LTM message This column will also be used to avoid concurrency or race condition problems that could occur if two or more management entities try to use the service at the same time.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ready(1), transmit(2), abort(3)

rcCfmTransmitLtmResult		1.3.6.1.4.1.2272.1.69.18.1.14
Display the LTM result.
Status: obsolete	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..1023)

rcCfmTransmitLtmFlag		1.3.6.1.4.1.2272.1.69.18.1.15
LTM result flag indicating LTM status or error code. Each enum value represents a status or error case. 1 - No error 2 - Ltm Internal Error 3 - Unknown Remote Maintenance End Point 4 - Invalid Remote Maintenance End Point Mac Address 5 - Unset Remote Maintenance End Point Mac Address 6 - Mep must be enabled in order to perform LTM 7 - No Ltr response received 8 - Linktrace to own Mep MAC is not sent 9 - Endpoint must be enabled in order to perform LTM 10 - Pbt-trunk must be enabled in order to perform LTM 11 - LTM completed 12 - LTM leaf node
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), internalError(2), noRemoteMep(3), invalidRemoteMepMac(4), noRemoteMepMacLearned(5), mepDisabled(6), noLtrResponse(7), ltmToOwnMepMac(8), epDisabled(9), trunkDisabled(10), ltmComplete(11), ltmLeafNode(12)

rcCfmTransmitLtmSourceMode		1.3.6.1.4.1.2272.1.69.18.1.16
Source modes of the transmit linktrace service.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nodal(1), smltVirtual(2), noVlanMac(3)

rcCfmLtrReplyTable		1.3.6.1.4.1.2272.1.69.33
This table contains a list of Linktrace replies received by a specific MEP in response to a linktrace message.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcCfmLtrReplyEntry

rcCfmLtrReplyEntry		1.3.6.1.4.1.2272.1.69.33.1
The Linktrace Reply table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcCfmLtrReplyEntry

rcCfmLtrReplyDomainIndex		1.3.6.1.4.1.2272.1.69.33.1.1
Maintenance Domain Index
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..2147483647

rcCfmLtrReplyAssociationIndex		1.3.6.1.4.1.2272.1.69.33.1.2
Maintenance Association Index
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..2147483647

rcCfmLtrReplyMepId		1.3.6.1.4.1.2272.1.69.33.1.3
Maintenance EndPoint ID
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..8191

rcCfmLtrReplySeqNumber		1.3.6.1.4.1.2272.1.69.33.1.4
The transaction identifier/sequence number returned by a previous transmit linktrace message command, indicating which LTM's response is going to be returned.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..2147483647

rcCfmLtrReplyHop		1.3.6.1.4.1.2272.1.69.33.1.5
The number of hops away from LTM initiator
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..255

rcCfmLtrReplyReceiveOrder		1.3.6.1.4.1.2272.1.69.33.1.6
An index to distinguish among multiple LTRs with the same LTR Transaction Identifier field value. This value is assigned sequentially from 1, in the order that the Linktrace Initiator received the LTRs.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..2147483647

rcCfmLtrReplyTtl		1.3.6.1.4.1.2272.1.69.33.1.7
Ttl field value for a returned LTR.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..255

rcCfmLtrReplyDomainName		1.3.6.1.4.1.2272.1.69.33.1.8
Maintenance Domain Name
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..22)

rcCfmLtrReplyAssociationName		1.3.6.1.4.1.2272.1.69.33.1.9
Maintenance Association Name
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..22)

rcCfmLtrReplyForwarded		1.3.6.1.4.1.2272.1.69.33.1.10
Indicates if a LTM was forwarded by the responding MP, as returned in the 'FwdYes' flag of the flags field.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcCfmLtrReplyTerminalMep		1.3.6.1.4.1.2272.1.69.33.1.11
A boolean value stating whether the forwarded LTM reached a MEP enclosing its MA, as returned in the Terminal MEP flag of the Flags field.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcCfmLtrReplyLastEgressIdentifier		1.3.6.1.4.1.2272.1.69.33.1.12
An octet field holding the Last Egress Identifier returned in the LTR Egress Identifier TLV of the LTR. The Last Egress Identifier identifies the MEP Linktrace Indicator that originated, or the Linktrace Responder that forwarded, the LTM to which this LTR is the response. This is the same value as the Egress Identifier TLV of that LTM.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(8)

rcCfmLtrReplyNextEgressIdentifier		1.3.6.1.4.1.2272.1.69.33.1.13
An octet field holding the Next Egress Identifier returned in the LTR Egress Identifier TLV of the LTR. The Next Egress Identifier Identifies the Linktrace Responder that transmitted this LTR, and can forward the LTM to the next hop. This is the same value as the Egress Identifier TLV of the forwarded LTM, if any. If the FwdYes bit of the Flags field is false, the contents of this field are undefined, and the field is ignored by the receiver.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(8)

rcCfmLtrReplyRelayAction		1.3.6.1.4.1.2272.1.69.33.1.14
Value returned in the Relay Action field.
Status: current	Access: read-only
OBJECT-TYPE
	CfmRelayActionFieldValue

rcCfmLtrReplySrcMac		1.3.6.1.4.1.2272.1.69.33.1.15
Mac address of the MP that respond to the LTM request for this LTR
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rcCfmLtrReplyIngressAction		1.3.6.1.4.1.2272.1.69.33.1.16
The value returned in the Ingress Action Field of the LTM. The value ingNoTlv(5) indicates that no Reply Ingress TLV was returned in the LTM.
Status: current	Access: read-only
OBJECT-TYPE
	CfmIngressActionFieldValue

rcCfmLtrReplyIngressMac		1.3.6.1.4.1.2272.1.69.33.1.17
Mac address returned in the ingress MAC address field. If the rcCfmLtrReplyIngress object contains the value ingNoTlv(5), then the contents of this object are meaningless.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rcCfmLtrReplyIngressPortIdSubtype		1.3.6.1.4.1.2272.1.69.33.1.18
Format of the Ingress Port ID. If the rcCfmLtrReplyIngress object contains the value ingNoTlv(5), then the contents of this object are meaningless.
Status: current	Access: read-only
OBJECT-TYPE
	LldpPortIdSubtype

rcCfmLtrReplyIngressPortId		1.3.6.1.4.1.2272.1.69.33.1.19
Ingress Port ID. The format of this object is determined by the value of the rcCfmLtrReplyIngressPortIdSubtype object. If the rcCfmLtrReplyIngress object contains the value ingNoTlv(5), then the contents of this object are meaningless.
Status: current	Access: read-only
OBJECT-TYPE
	LldpPortId

rcCfmLtrReplyEgressAction		1.3.6.1.4.1.2272.1.69.33.1.20
The value returned in the Egress Action Field of the LTM. The value egrNoTlv(5) indicates that no Reply Egress TLV was returned in the LTM.
Status: current	Access: read-only
OBJECT-TYPE
	CfmEgressActionFieldValue

rcCfmLtrReplyEgressMac		1.3.6.1.4.1.2272.1.69.33.1.21
Mac address returned in the egress MAC address field. If the rcCfmLtrReplyEgress object contains the value egrNoTlv(5), then the contents of this object are meaningless.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rcCfmLtrReplyEgressPortIdSubtype		1.3.6.1.4.1.2272.1.69.33.1.22
Format of the Egress Port ID. If the rcCfmLtrReplyEgress object contains the value egrNoTlv(5), then the contents of this object are meaningless.
Status: current	Access: read-only
OBJECT-TYPE
	LldpPortIdSubtype

rcCfmLtrReplyEgressPortId		1.3.6.1.4.1.2272.1.69.33.1.23
Egress Port ID. The format of this object is determined by the value of the rcCfmLtrReplyEgressPortIdSubtype object. If the rcCfmLtrReplyEgress object contains the value egrNoTlv(5), then the contents of this object are meaningless.
Status: current	Access: read-only
OBJECT-TYPE
	LldpPortId

rcCfmTransmitL2PingTable		1.3.6.1.4.1.2272.1.69.34
Connectivity Fault Management transmit L2Ping table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcCfmTransmitL2PingEntry

rcCfmTransmitL2PingEntry		1.3.6.1.4.1.2272.1.69.34.1
Connectivity Fault Management Maintenance EndPoint L2Ping entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcCfmTransmitL2PingEntry

rcCfmTransmitL2PingVlanId		1.3.6.1.4.1.2272.1.69.34.1.1
A value that uniquely identifies the Customer Vlan
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..4094

rcCfmTransmitL2PingDestMacAddress		1.3.6.1.4.1.2272.1.69.34.1.2
An indication of the target MAC Address field to be transmitted
Status: current	Access: read-write
OBJECT-TYPE
	MacAddress

rcCfmTransmitL2PingHostName		1.3.6.1.4.1.2272.1.69.34.1.3
The target host name
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..255)

rcCfmTransmitL2PingDestIsHostName		1.3.6.1.4.1.2272.1.69.34.1.4
True indicates that the host name is used for L2Ping transmission
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcCfmTransmitL2PingMessages		1.3.6.1.4.1.2272.1.69.34.1.5
The number of L2Ping messages to be transmitted.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..200

rcCfmTransmitL2PingPriority		1.3.6.1.4.1.2272.1.69.34.1.6
Priority. 3 bit value to be used in the VLAN hdr, if present in the transmitted frame.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..7

rcCfmTransmitL2PingTimeoutInt		1.3.6.1.4.1.2272.1.69.34.1.7
The interval to wait for an L2Ping time-out with a range of (1..10) seconds with a default value of 3 seconds.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..10

rcCfmTransmitL2PingTestPattern		1.3.6.1.4.1.2272.1.69.34.1.8
The test pattern to use in the L2Ping PDU with range of values namely allZero, allZeroCrc, pseudoRandomBitSequence and pseudoRandomBitSequenceCrc and with a default value of allZero. value meaning -------- ------- allZero(1) Null signal without CRC-32 allZeroCrc(2) Null signal with CRC-32 pseudoRandomBitSequence(3) PRBS 1/2^31-1 without CRC-32 pseudoRandomBitSequenceCrc(4) PBRS 1/2^31-1 with CRC-32
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	allZero(1), allZeroCrc(2), pseudoRandomBitSequence(3), pseudoRandomBitSequenceCrc(4)

rcCfmTransmitL2PingDataSize		1.3.6.1.4.1.2272.1.69.34.1.9
An arbitrary amount of data to be included in the data TLV, if the Data Size is selected to be sent.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..400

rcCfmTransmitL2PingFrameSize		1.3.6.1.4.1.2272.1.69.34.1.10
If the frame size is specified then the data size shall be internally calculated and the calculated data size shall be included in the data TLV.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..9600

rcCfmTransmitL2PingSourceMode		1.3.6.1.4.1.2272.1.69.34.1.11
Source modes of the transmit loopback service.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nodal(1), smltVirtual(2), noVlanMac(3)

rcCfmTransmitL2PingSeqNumber		1.3.6.1.4.1.2272.1.69.34.1.12
The transaction identifier/sequence number of the first loopback message (to be) sent.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcCfmTransmitL2PingResultOk		1.3.6.1.4.1.2272.1.69.34.1.13
Indicates the result of the operation: -true. The L2Ping Message(s) will be (or have been) sent. -false. The L2Ping Message(s) will not be sent.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcCfmTransmitL2PingStatus		1.3.6.1.4.1.2272.1.69.34.1.14
Status of the transmit loopback service: -ready. The service is available. -transmit. The service is transmitting, or about to transmit, the L2Ping messages. -abort The service is aborted or about to abort the L2Ping messages. This column will also be used to avoid concurrency or race condition problems that could occur if two or more management entities try to use the service at the same time.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ready(1), transmit(2), abort(3)

rcCfmTransmitL2PingResult		1.3.6.1.4.1.2272.1.69.34.1.15
Display the L2Ping result.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..799)

rcCfmTransmitL2TraceTable		1.3.6.1.4.1.2272.1.69.35
Connectivity Fault Management transmit L2Trace table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcCfmTransmitL2TraceEntry

rcCfmTransmitL2TraceEntry		1.3.6.1.4.1.2272.1.69.35.1
Connectivity Fault Management Maintenance EndPoint L2Trace entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcCfmTransmitL2TraceEntry

rcCfmTransmitL2TraceVlanId		1.3.6.1.4.1.2272.1.69.35.1.1
A value that uniquely identifies the Customer Vlan
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..4094

rcCfmTransmitL2TracePriority		1.3.6.1.4.1.2272.1.69.35.1.2
Priority. 3 bit value to be used in the VLAN hdr, if present in the transmitted frame.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..7

rcCfmTransmitL2TraceDestMacAddress		1.3.6.1.4.1.2272.1.69.35.1.3
An indication of the target MAC Address field to be transmitted
Status: current	Access: read-write
OBJECT-TYPE
	MacAddress

rcCfmTransmitL2TraceHostName		1.3.6.1.4.1.2272.1.69.35.1.4
The target host name
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..255)

rcCfmTransmitL2TraceIsid		1.3.6.1.4.1.2272.1.69.35.1.5
Isid Id
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..16777215

rcCfmTransmitL2TraceNickName		1.3.6.1.4.1.2272.1.69.35.1.6
Local Node nick name
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(7)

rcCfmTransmitL2TraceDestIsHostName		1.3.6.1.4.1.2272.1.69.35.1.7
True indicates that the host name is used for L2Trace transmission
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcCfmTransmitL2TraceIsidTree		1.3.6.1.4.1.2272.1.69.35.1.8
True indicates that the multicast tree will be traced. False indicates that the unicast path will be traced
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcCfmTransmitL2TraceTtl		1.3.6.1.4.1.2272.1.69.35.1.9
The number of hops remaining to this L2Trace. Decremented by 1 by each Bridge that handles the L2Trace. The decremented value is returned in the L2Trace. If 0 on output, the L2Trace is not transmitted to the next hop. The value of the TTL Field in the L2Trace transmitted by the originating MEP is controlled by a Managed Object; The default value if none is specified is 64.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..255

rcCfmTransmitL2TraceSourceMode		1.3.6.1.4.1.2272.1.69.35.1.10
Source modes of the transmit loopback service.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nodal(1), smltVirtual(2), noVlanMac(3)

rcCfmTransmitL2TraceSeqNumber		1.3.6.1.4.1.2272.1.69.35.1.11
The transaction identifier/sequence number of the first loopback message (to be) sent.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcCfmTransmitL2TraceResultOk		1.3.6.1.4.1.2272.1.69.35.1.12
Indicates the result of the operation: -true. The L2Trace Message(s) will be (or have been) sent. -false. The L2Trace Message(s) will not be sent.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcCfmTransmitL2TraceStatus		1.3.6.1.4.1.2272.1.69.35.1.13
Status of the transmit loopback service: -ready. The service is available. -transmit. The service is transmitting, or about to transmit, the L2Trace messages. -abort The service is aborted or about to abort the L2Trace messages. This column will also be used to avoid concurrency or race condition problems that could occur if two or more management entities try to use the service at the same time.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ready(1), transmit(2), abort(3)

rcCfmTransmitL2TraceFlag		1.3.6.1.4.1.2272.1.69.35.1.14
L2Trace result flag indicating L2Trace status or error code. Each enum value represents a status or error case. 1 - No error 2 - L2Trace Internal Error 3 - Invalid Mac Address 4 - Mep must be enabled in order to perform L2Trace 5 - No L2Trace response received 6 - L2Trace to own Mep MAC is not sent 7 - L2Trace completed 8 - Lookup failure for L2Trace 9 - On a leaf node in the i-sid tree 10 - Not in the i-sid tree 11 - Requested SMLT Source from Non-Primary Node
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), internalError(2), invalidMac(3), mepDisabled(4), noL2TraceResponse(5), l2TraceToOwnMepMac(6), l2TraceComplete(7), l2TraceLookupFailure(8), l2TraceLeafNode(9), l2TraceNotInTree(10), l2TraceSmltNotPrimary(11)

rcCfmL2TraceReplyTable		1.3.6.1.4.1.2272.1.69.36
This table contains a list of l2trace replies received by a specific MEP in response to a linktrace message.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcCfmL2TraceReplyEntry

rcCfmL2TraceReplyEntry		1.3.6.1.4.1.2272.1.69.36.1
The Linktrace Reply table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcCfmL2TraceReplyEntry

rcCfmL2TraceReplyVlanId		1.3.6.1.4.1.2272.1.69.36.1.1
A value that uniquely identifies the Customer Vlan
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..4094

rcCfmL2TraceReplySeqNumber		1.3.6.1.4.1.2272.1.69.36.1.2
The transaction identifier/sequence number returned by a previous transmit linktrace message command, indicating which L2Trace's response is going to be returned.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..2147483647

rcCfmL2TraceReplyHop		1.3.6.1.4.1.2272.1.69.36.1.3
The number of hops away from L2Trace initiator.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..255

rcCfmL2TraceReplyReceiveOrder		1.3.6.1.4.1.2272.1.69.36.1.4
An index to distinguish among multiple L2Trace responses with the same Transaction Identifier field value. This value is assigned sequentially from 1, in the order that the Linktrace Initiator received the responses.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..2147483647

rcCfmL2TraceReplyTtl		1.3.6.1.4.1.2272.1.69.36.1.5
Ttl field value for a returned L2Trace response.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..255

rcCfmL2TraceReplySrcMac		1.3.6.1.4.1.2272.1.69.36.1.6
Mac address of the MP that respond to the L2Trace request for this L2traceReply
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rcCfmL2TraceReplyHostName		1.3.6.1.4.1.2272.1.69.36.1.7
The host name of the replying node
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..255)

rcCfmL2TraceReplyLastSrcMac		1.3.6.1.4.1.2272.1.69.36.1.8
The MAC address of the node that forwarded the L2Trace to the responding node
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rcCfmL2TraceReplyLastHostName		1.3.6.1.4.1.2272.1.69.36.1.9
The host name of the node that forwarded the L2Trace to the responding node
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..255)

rcCfmTransmitL2IpPingTable		1.3.6.1.4.1.2272.1.69.37
Connectivity Fault Management transmit L2IpPing table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcCfmTransmitL2IpPingEntry

rcCfmTransmitL2IpPingEntry		1.3.6.1.4.1.2272.1.69.37.1
L2IpPing entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcCfmTransmitL2IpPingEntry

rcCfmTransmitL2IpPingIpAddrType		1.3.6.1.4.1.2272.1.69.37.1.1
The address type of destination IP Address
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddressType

rcCfmTransmitL2IpPingIpAddr		1.3.6.1.4.1.2272.1.69.37.1.2
Destination IP Address. Support ipv4 at this time
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddress

rcCfmTransmitL2IpPingVrfId		1.3.6.1.4.1.2272.1.69.37.1.3
VRF ID
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcCfmTransmitL2IpPingVrfName		1.3.6.1.4.1.2272.1.69.37.1.4
The Name of the Virtual Router
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..64)

rcCfmTransmitL2IpPingMessages		1.3.6.1.4.1.2272.1.69.37.1.5
The number of L2IpPing messages to be transmitted per mac/vlan pair.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..200

rcCfmTransmitL2IpPingTimeoutInt		1.3.6.1.4.1.2272.1.69.37.1.6
The interval to wait for an L2IpPing time-out with a range of (1..10) seconds with a default value of 3 seconds.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..10

rcCfmTransmitL2IpPingTestPattern		1.3.6.1.4.1.2272.1.69.37.1.7
The test pattern to use in the L2IpPing PDUs with range of values namely allZero, allZeroCrc, pseudoRandomBitSequence and pseudoRandomBitSequenceCrc and with a default value of allZero. value meaning -------- ------- allZero(1) Null signal without CRC-32 allZeroCrc(2) Null signal with CRC-32 pseudoRandomBitSequence(3) PRBS 1/2^31-1 without CRC-32 pseudoRandomBitSequenceCrc(4) PBRS 1/2^31-1 with CRC-32
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	allZero(1), allZeroCrc(2), pseudoRandomBitSequence(3), pseudoRandomBitSequenceCrc(4)

rcCfmTransmitL2IpPingDataSize		1.3.6.1.4.1.2272.1.69.37.1.8
An arbitrary amount of data to be included in the data TLV, if the Data Size is selected to be sent.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..400

rcCfmTransmitL2IpPingStatus		1.3.6.1.4.1.2272.1.69.37.1.9
Status of the transmit loopback service: -ready. The service is available. -transmit. The service is transmitting, or about to transmit, the L2IpPing messages. -abort The service is aborted or about to abort the L2IpPing messages. This column will also be used to avoid concurrency or race condition problems that could occur if two or more management entities try to use the service at the same time.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	ready(1), transmit(2), abort(3)

rcCfmTransmitL2IpPingResultOk		1.3.6.1.4.1.2272.1.69.37.1.10
Indicates the result of the operation: -true. L2IpPing Message(s) will be/have been sent. -false. L2IpPing Message(s) will not be sent.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcCfmTransmitL2IpPingPathsFound		1.3.6.1.4.1.2272.1.69.37.1.11
The number of paths found to execute l2ping command
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcCfmTransmitL2IpPingRowStatus		1.3.6.1.4.1.2272.1.69.37.1.12
Used to create/delete entries in the rcCfmTransmitL2IpPingTable. Deletion of an entry in this table results in corresponding rcCfmL2IpPingReplyTable entries being deleted.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcCfmL2IpPingReplyTable		1.3.6.1.4.1.2272.1.69.38
This table contains a list of l2 ip ping replies received
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcCfmL2IpPingReplyEntry

rcCfmL2IpPingReplyEntry		1.3.6.1.4.1.2272.1.69.38.1
The L2 Ip Ping Reply table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcCfmL2IpPingReplyEntry

rcCfmL2IpPingReplyIpAddrType		1.3.6.1.4.1.2272.1.69.38.1.1
The address type of destination IP Address
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddressType

rcCfmL2IpPingReplyIpAddr		1.3.6.1.4.1.2272.1.69.38.1.2
Destination IP Address. Support ipv4 at this time
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddress

rcCfmL2IpPingReplySendOrder		1.3.6.1.4.1.2272.1.69.38.1.3
An index to distinguish among multiple L2Ping sessions This value is assigned sequentially from 1. It denotes order that sessions were sent. It correlates to the number of paths found and stored in the rcCfmTransmitL2IpPingEntry.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..2147483647

rcCfmL2IpPingReplyVrfId		1.3.6.1.4.1.2272.1.69.38.1.4
VRF ID
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcCfmL2IpPingReplyVlanId		1.3.6.1.4.1.2272.1.69.38.1.5
Vlan found from L3 lookup and used for transmission
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..4094

rcCfmL2IpPingReplyDestMacAddress		1.3.6.1.4.1.2272.1.69.38.1.6
An indication of the target MAC Address transmitted
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rcCfmL2IpPingReplyPortNum		1.3.6.1.4.1.2272.1.69.38.1.7
Either the value '0', or the port number of the port used for the l2ping.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcCfmL2IpPingReplyDestHostName		1.3.6.1.4.1.2272.1.69.38.1.8
The host name of the responding node
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..255)

rcCfmL2IpPingReplySize		1.3.6.1.4.1.2272.1.69.38.1.9
The number of bytes of data sent
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..9600

rcCfmL2IpPingReplyPktsTx		1.3.6.1.4.1.2272.1.69.38.1.10
Number of Packets transmitted for this vlan/mac
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcCfmL2IpPingReplyPktsRx		1.3.6.1.4.1.2272.1.69.38.1.11
Number of Packets received for this vlan/mac
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcCfmL2IpPingReplyPercentLossWhole		1.3.6.1.4.1.2272.1.69.38.1.12
Percentage of packet loss for this vlan/mac
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..100

rcCfmL2IpPingReplyPercentLossFract		1.3.6.1.4.1.2272.1.69.38.1.13
Percentage of packet loss for this vlan/mac
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..100

rcCfmL2IpPingReplyMinRoundTrip		1.3.6.1.4.1.2272.1.69.38.1.14
Min time for round-trip for this vlan/mac in us
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcCfmL2IpPingReplyMaxRoundTrip		1.3.6.1.4.1.2272.1.69.38.1.15
Max time for round-trip for this vlan/mac in us
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcCfmL2IpPingReplyRttAvgWhole		1.3.6.1.4.1.2272.1.69.38.1.16
Average time for round-trip for this vlan/mac in us
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcCfmL2IpPingReplyRttAvgFract		1.3.6.1.4.1.2272.1.69.38.1.17
Fractional portion of Average time for round-trip
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcCfmL2IpPingReplyFlag		1.3.6.1.4.1.2272.1.69.38.1.18
Result flag indicating status or error code. Each enum value represents a status or error case. 1 - No error 2 - Internal Error 3 - Invalid Ip 4 - L2Trace completed 5 - Lookup failure for IP (no vlan/mac entries)
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), internalError(2), invalidMac(3), mepDisabled(4), invalidMD(5), invalidMA(6), noMepFound(7), unknownServiceInstance(8), l2PingToOwnMepMac(9), l2PingComplete(10)

rcCfmTransmitL2IpTraceTable		1.3.6.1.4.1.2272.1.69.39
Connectivity Fault Management transmit L2IpTrace table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcCfmTransmitL2IpTraceEntry

rcCfmTransmitL2IpTraceEntry		1.3.6.1.4.1.2272.1.69.39.1
L2IpTrace entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcCfmTransmitL2IpTraceEntry

rcCfmTransmitL2IpTraceIpAddrType		1.3.6.1.4.1.2272.1.69.39.1.1
The address type of destination IP Address
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddressType

rcCfmTransmitL2IpTraceIpAddr		1.3.6.1.4.1.2272.1.69.39.1.2
Destination IP Address. Support ipv4 at this time
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddress

rcCfmTransmitL2IpTraceVrfId		1.3.6.1.4.1.2272.1.69.39.1.3
VRF ID
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcCfmTransmitL2IpTraceVrfName		1.3.6.1.4.1.2272.1.69.39.1.4
The Name of the Virtual Router
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..64)

rcCfmTransmitL2IpTraceTtl		1.3.6.1.4.1.2272.1.69.39.1.5
The number of hops remaining to this L2Trace. Decremented by 1 by each Bridge that handles the L2Trace. The decremented value is returned in the L2Trace. If 0 on output, the L2Trace is not transmitted to the next hop. The value of the TTL Field in the L2Trace transmitted by the originating MEP is controlled by a Managed Object; The default value if none is specified is 64.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..255

rcCfmTransmitL2IpTraceStatus		1.3.6.1.4.1.2272.1.69.39.1.6
Status of the transmit loopback service: -ready. The service is available. -transmit. The service is transmitting, or about to transmit, the L2Trace messages. -abort The service is aborted or about to abort the L2Trace messages. This column will also be used to avoid concurrency or race condition problems that could occur if two or more management entities try to use the service at the same time.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	ready(1), transmit(2), abort(3)

rcCfmTransmitL2IpTraceResultOk		1.3.6.1.4.1.2272.1.69.39.1.7
Indicates the result of the operation: -true. The Trace Message(s) will be/have been sent. -false. The Trace Message(s) will not be sent.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rcCfmTransmitL2IpTracePathsFound		1.3.6.1.4.1.2272.1.69.39.1.8
The number of paths found to execute l2trace command
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcCfmTransmitL2IpTraceRowStatus		1.3.6.1.4.1.2272.1.69.39.1.9
Used to create/delete entries in the rcCfmTransmitL2IpTraceTable. Deletion of an entry in this table results in corresponding rcCfmL2IpTraceReplyTable entries being deleted.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

rcCfmL2IpTraceReplyTable		1.3.6.1.4.1.2272.1.69.40
This table contains a list of l2 ip trace replies received by a specific MEP in response to a linktrace message.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcCfmL2IpTraceReplyEntry

rcCfmL2IpTraceReplyEntry		1.3.6.1.4.1.2272.1.69.40.1
The L2 Ip Trace Reply table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcCfmL2IpTraceReplyEntry

rcCfmL2IpTraceReplyIpAddrType		1.3.6.1.4.1.2272.1.69.40.1.1
The address type of destination IP Address
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddressType

rcCfmL2IpTraceReplyIpAddr		1.3.6.1.4.1.2272.1.69.40.1.2
Destination IP Address. Support ipv4 at this time
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddress

rcCfmL2IpTraceReplySendOrder		1.3.6.1.4.1.2272.1.69.40.1.3
An index to distinguish among multiple L2Trace sessions This value is assigned sequentially from 1. It denotes order that sessions were sent. It correlates to the number of paths found and stored in the rcCfmTransmitL2IpTraceEntry.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..2147483647

rcCfmL2IpTraceReplyHop		1.3.6.1.4.1.2272.1.69.40.1.4
The number of L2 hops away from L2Trace initiator.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..255

rcCfmL2IpTraceReplyReceiveOrder		1.3.6.1.4.1.2272.1.69.40.1.5
An index to distinguish among multiple L2Trace responses with the same Send Transaction Identifier field value. This value is assigned sequentially from 1, in the order that the Linktrace Initiator received the responses. A zero value may be seen in error conditions
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..2147483647

rcCfmL2IpTraceReplyTtl		1.3.6.1.4.1.2272.1.69.40.1.6
Ttl field value for a returned L2Trace response.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..255

rcCfmL2IpTraceReplyVrfId		1.3.6.1.4.1.2272.1.69.40.1.7
VRF ID
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcCfmL2IpTraceReplyVlanId		1.3.6.1.4.1.2272.1.69.40.1.8
Vlan found from L3 lookup and used for transmission
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..4094

rcCfmL2IpTraceReplyDestMacAddress		1.3.6.1.4.1.2272.1.69.40.1.9
An indication of the target MAC Address transmitted
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rcCfmL2IpTraceReplySeqNumber		1.3.6.1.4.1.2272.1.69.40.1.10
The transaction identifier/sequence number used in linktrace message packet
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

rcCfmL2IpTraceReplyPortNum		1.3.6.1.4.1.2272.1.69.40.1.11
Either the value '0', or the port number of the port used for the l2trace.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

rcCfmL2IpTraceReplySrcMac		1.3.6.1.4.1.2272.1.69.40.1.12
Mac address of the MP that responded to L2Trace request for this L2traceReply
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rcCfmL2IpTraceReplyHostName		1.3.6.1.4.1.2272.1.69.40.1.13
The host name of the replying node
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..255)

rcCfmL2IpTraceReplyLastSrcMac		1.3.6.1.4.1.2272.1.69.40.1.14
The MAC address of the node that forwarded the L2Trace to the responding node
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rcCfmL2IpTraceReplyLastHostName		1.3.6.1.4.1.2272.1.69.40.1.15
The host name of the node that forwarded the L2Trace to the responding node
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..255)

rcCfmL2IpTraceReplyFlag		1.3.6.1.4.1.2272.1.69.40.1.16
L2Trace result flag indicating status or error code. Each enum value represents a status or error case. 1 - No error 2 - L2Trace Internal Error 3 - Invalid Mac Address 4 - Mep must be enabled in order to perform L2Trace 5 - No L2Trace response received 6 - L2Trace to own Mep MAC is not sent 7 - L2Trace completed 8 - Lookup failure for L2Trace
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), internalError(2), invalidMac(3), mepDisabled(4), noL2TraceResponse(5), l2TraceToOwnMepMac(6), l2TraceComplete(7), l2TraceLookupFailure(8)