RAD-MIB

File: RAD-MIB.mib (1910536 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-TC	IF-MIB
PerfHist-TC-MIB	SNMP-FRAMEWORK-MIB	Q-BRIDGE-MIB
DS3-MIB	IANAifType-MIB	DS1-MIB
BRIDGE-MIB	ATM-MIB	INET-ADDRESS-MIB
DISMAN-SCHEDULE-MIB	LLDP-MIB	DOT3-OAM-MIB
IEEE8021-CFM-MIB

Imported symbols

TimeTicks	enterprises	IpAddress
OBJECT-TYPE	Integer32	Counter32
Gauge32	OBJECT-IDENTITY	NOTIFICATION-TYPE
Unsigned32	Counter64	RowStatus
DateAndTime	TimeStamp	TEXTUAL-CONVENTION
DisplayString	MacAddress	RowPointer
TruthValue	InterfaceIndex	ifAlias
ifIndex	ifDescr	PerfCurrentCount
PerfIntervalCount	PerfTotalCount	SnmpAdminString
VlanId	PortList	dot1qVlanStaticEntry
dsx3LineStatus	dsx3LoopbackStatus	dsx3ConfigEntry
IANAifType	dsx1CurrentIndex	dsx1IntervalIndex
dsx1IntervalNumber	dsx1LineIndex	dsx1TotalIndex
dsx1LineStatus	dsx1LineStatusLastChange	dsx1LoopbackStatus
Timeout	BridgeId	dot1dBasePortEntry
atmVplVpi	atmVclVpi	atmVclVci
atmVpCrossConnectEntry	atmVcCrossConnectEntry	atmTrafficDescrParamEntry
InetAddressType	InetAddress	schedEntry
LldpPortIdSubtype	dot3OamEntry	dot3OamOperStatus
dot1agCfmMdIndex	dot1agCfmMaIndex	dot1agCfmMepIdentifier
dot1agCfmMepDbRMepIdentifier

Defined Types

MngEntry
SEQUENCE
	mngID	Integer32
	mngIP	IpAddress
	mngIPMask	IpAddress
	mngTrapMask	Integer32
	mngAlarmTrapMask	OCTET STRING
	mngSnmpTrapUdpPort	Unsigned32

TrapEntry
SEQUENCE
	trapID	Integer32
	trapVal	DisplayString
	trapTimeSinceOccurrence	TimeTicks
	trapNumeric	Integer32

IntSwdlEntry
SEQUENCE
	intSwdlObjIdx	Integer32
	intSwdlFileIdx	Integer32
	intSwdlFileName	DisplayString
	intSwdlFileSwVer	DisplayString
	intSwdlSwDate	DisplayString
	intSwdlSize	DisplayString
	intSwdlCmd	INTEGER
	intSwdlToSubSystem	OCTET STRING
	intSwdlCardType	INTEGER
	intSwdlFlashIdx	Integer32

SwdlStatusEntry
SEQUENCE
	swdlStatusTypeIdx	Integer32
	swdlStatusIdx	Integer32
	swdlStatusFileName	DisplayString
	swdlStatusSlot	DisplayString
	swdlStatusSubSystem	DisplayString
	swdlStatusStatus	Integer32
	swdlStatusTime	DisplayString

AutoFileTransferEntry
SEQUENCE
	autoFileTransferType	INTEGER
	autoFileTransferServerIp	IpAddress
	autoFileTransferFileName	SnmpAdminString
	autoFileTransferScheduling	INTEGER
	autoFileTransferTimeRecurrence	Integer32
	autoFileTransferOccurrenceRecurrence	Integer32

SchedXEntry
SEQUENCE
	schedYear	Unsigned32
	schedWeekInMonth	INTEGER
	schedParam	Integer32

PhysicalConnectorEntry
SEQUENCE
	portIdx	Integer32
	physicalConnector	INTEGER
	portOptWaveLength	INTEGER
	portOptMode	INTEGER
	portBalance	INTEGER
	portDdmSupport	INTEGER
	portMfgName	SnmpAdminString
	portTypicalMaxRange	Unsigned32
	physicalConnectorString	SnmpAdminString
	portVendorPartNo	SnmpAdminString

PrtSpEntry
SEQUENCE
	prtSupervisoryIndex	Integer32
	prtSupervisoryRate	INTEGER
	prtSupervisoryDataBits	INTEGER
	prtSupervisoryParity	INTEGER
	prtSupervisoryStopBits	INTEGER
	prtSupervisoryUsage	INTEGER
	prtSupervisoryInterface	INTEGER
	prtSupervisoryCTS	INTEGER
	prtSupervisoryDcdDelay	INTEGER
	prtSupervisoryDSR	INTEGER
	prtSupervisoryRoutProtocol	INTEGER

PrtPerfEntry
SEQUENCE
	prtPerfIdx	Integer32
	prtPerfPeriodRef	INTEGER
	prtPerfElapsedTime	Integer32
	prtPerfUAS	Integer32
	prtPerfES	Integer32
	prtPerfSES	Integer32
	prtPerfBBE	Integer32
	prtPerfBlocksPerSec	Integer32
	prtPerfTimeTag	TimeTicks
	prtPerfSaveAndResetCmd	INTEGER

PrtTestEntry
SEQUENCE
	prtTestIdx	Integer32
	prtTestCmdAndStatus	Integer32
	prtBertCounter	Integer32
	prtTestInitiator	INTEGER
	prtTestTimeout	Integer32
	prtTestVctRxResult	INTEGER
	prtTestVctTxResult	INTEGER
	prtTestVctRxDistance	Integer32
	prtTestVctTxDistance	Integer32
	prtTestVctCmd	INTEGER
	prtTestVctRxCrossPair	Integer32
	prtTestVctTxCrossPair	Integer32
	prtTestActivationDelay	Unsigned32
	prtTestMacSwapLoopDataMode	INTEGER
	prtTestMacSwapLoopVlanId	Integer32
	prtTestMacSwapLoopDirection	INTEGER
	prtTestMacSwapLoopDestAddr	MacAddress
	prtTestMacSwapLoopSrcAddr	MacAddress
	prtTestOamMinRoundTripDelay	Unsigned32
	prtTestOamMaxRoundTripDelay	Unsigned32
	prtTestOamAvgRoundTripDelay	Unsigned32
	prtTestOamTxInterval	Unsigned32
	prtTestDestinationIpAddress	IpAddress
	prtTestTTL	Unsigned32
	prtTestBwProfile	Unsigned32

PrtParamEntry
SEQUENCE
	prtParamIdx	Integer32
	prtControlCnfg	Integer32
	prtParamClkSrc	INTEGER
	prtParamPhantom	INTEGER
	prtParamResetStatsCmd	INTEGER
	prtParamLastResetStatsTime	TimeStamp
	prtParamInterfaceType	INTEGER
	prtParamClearAlarm	INTEGER
	prtParamLeds	OCTET STRING
	prtParamLineLength	INTEGER
	prtParamUsage	INTEGER
	prtParamMappingMode	INTEGER
	prtParamAlarmIndication	INTEGER
	prtParamClkQualityLevel	OCTET STRING
	prtParamClkWaveShape	INTEGER
	prtParamStatus	INTEGER
	prtParamSignalLevel	Integer32
	prtParamClkUserQualityLevel	OCTET STRING
	prtParamDataRate	Unsigned32
	prtParamLoopDetect	INTEGER
	prtParamActUponLoopDetect	OCTET STRING
	prtParamPSNLayer	INTEGER
	prtParamRxSsm	INTEGER
	prtParamClkSsmRxSource	INTEGER
	prtParamFarEndDevice	Unsigned32
	prtParamTxClk	INTEGER

PrtIpParamEntry
SEQUENCE
	prtIpParamConfigIdx	Integer32
	prtIpParamSlotIdx	Integer32
	prtIpParamIdx	Integer32
	prtIpParamHostIP	IpAddress
	prtIpParamHostMask	IpAddress
	prtIpParamDefaultGateway	IpAddress
	prtIpParamMediaMode	INTEGER
	prtIpParamMediaRate	INTEGER
	prtIpParamMngVlanSupport	INTEGER
	prtIpParamMngVlanId	Integer32
	prtIpParamMngVlanPriority	Integer32
	prtIpParamRingMode	INTEGER
	prtIpParamProtIpEnable	INTEGER
	prtIpParamTrafficPriority	INTEGER
	prtIpParamRemoteIP	IpAddress
	prtIpParamMaxTxBandwidth	INTEGER
	prtIpParamTos	Integer32
	prtIpParamConnect	INTEGER
	prtIpParamAgingTime	Integer32
	prtIpParamEncapsulationProt	INTEGER
	prtIpParamEncapProtPort	Integer32
	prtIpParamVlanSupport	INTEGER
	prtIpParamVlanId	Integer32
	prtIpParamVlanPriority	Integer32
	prtIpParamDoubleTagVlanId	Integer32
	prtIpParamDoubleTagVlanPriority	Integer32
	prtIpParamVlanTagging	INTEGER
	prtIpParamRateLimit	Integer32
	prtIpParamDefInterface	Integer32
	prtIpParamMng	INTEGER
	prtIpParamFloodedRateLimit	Integer32
	prtIpParamBurstSize	Unsigned32
	prtIpParamLimitPacketType	INTEGER
	prtIpParamKeepAliveInterval	Integer32
	prtIpParamKeepAliveThresh	Integer32
	prtIpParamP2pKeepAliveVlanId	Integer32
	prtIpParamP2pKeepAliveVlanPrio	Integer32
	prtIpParamRingAdjacentMacAddr	MacAddress

PrtClkSrcEntry
SEQUENCE
	prtClkSrcCnfgIdx	Integer32
	prtClkSrcPrtIdx	Integer32
	prtClkSrcIdx	INTEGER
	prtClkSrcMode	INTEGER
	prtClkSrcPrt	Integer32

OptPrtMonitorEntry
SEQUENCE
	optPrtMonitorPrtIdx	Integer32
	optPrtMonitorSample	INTEGER
	optPrtMonitorTxPower	Integer32
	optPrtMonitorLaserBias	Integer32
	optPrtMonitorLaserTemp	Integer32
	optPrtMonitorRxPower	Integer32
	optPrtMonitorSupplyVoltage	Integer32

OptPrtCnfgEntry
SEQUENCE
	optPrtCnfgIdx	Unsigned32
	optPrtCnfgPrtIdx	Unsigned32
	optPrtCnfgALS	INTEGER

SystemPsEntry
SEQUENCE
	systemPsIndex1	Integer32
	systemPsIndex2	Integer32
	systemPsType	INTEGER
	systemPsStatus	INTEGER
	systemPsHotSwap	INTEGER

XcEntry
SEQUENCE
	xcIndex	Integer32
	xcIfIndex1	Integer32
	xcVpi	Integer32
	xcVci	Integer32
	xcIfIndex2	Integer32
	xcRowStatus	RowStatus
	xcDescr	DisplayString
	xcAdminStatus	INTEGER
	xcOperStatus	INTEGER
	xcAttachedIfType	INTEGER
	xcInputPriority	Integer32
	xcBitMapping	Integer32

ModlParamEntry
SEQUENCE
	modlParamIndex	Integer32
	modlParamReset	INTEGER
	modlParamSwdlStatus	INTEGER
	modlParamLeds	OCTET STRING
	modlParamType	INTEGER
	modlParamSwVer	DisplayString

SysIfEntityType
INTEGER	other(1), ethernetLan(6), atm(37), fastEther(62), ipForward(142), teLink(200), bridge(209)

IfCreateEntry
SEQUENCE
	ifCreateEntityType	SysIfEntityType
	ifCreateEntityIdx	Integer32
	ifCreateNumber	Integer32
	ifCreateRowStatus	RowStatus
	ifCreateType	IANAifType
	ifCreateIndex	Integer32
	ifCreateConnectedTo	Integer32
	ifCreateParams	Unsigned32
	ifCreateConnectionPointer	RowPointer

IfPerfEntry
SEQUENCE
	ifPerfCounterType	Integer32
	ifPerfLowCounterPart	Unsigned32
	ifPerfHighCounterPart	Unsigned32
	ifPerfHCCounter	Counter64

SystemOamEntry
SEQUENCE
	systemOamCnfgIdx	Integer32
	systemOamFrequency	Integer32
	systemOamTimeoutCycles	Integer32
	systemOamLinkCheck	INTEGER

SystemOamDescrEntry
SEQUENCE
	systemOamDescrIdx	Integer32
	systemOamDescrRowStatus	RowStatus
	systemOamDescrMode	INTEGER
	systemOamDescrCCDirection	INTEGER
	systemOamDescrLoopbackOperation	INTEGER
	systemOamDescrLoopbackDestAddr	OCTET STRING
	systemOamDescrXcCounter	Gauge32

BitMappingEntry
SEQUENCE
	bitMappingLocation	Integer32
	bitMappingIndex	Integer32

HostEntry
SEQUENCE
	hostIndex	Integer32
	hostIP	IpAddress
	hostIPMask	IpAddress
	hostDefaultNextHop	IpAddress
	hostMode	Integer32
	hostParam1	Integer32
	hostParam2	Integer32
	hostParam3	Integer32
	hostRowStatus	RowStatus
	hostVlanTagging	INTEGER
	hostVlanId	Integer32
	hostVlanPriority	Integer32

InvNameXCEntry
SEQUENCE
	invNameXC	SnmpAdminString
	invNameXCType	OBJECT IDENTIFIER
	invNameXCIndex	Integer32

RowInfoEntry
SEQUENCE
	rowInfoTableId	OBJECT IDENTIFIER
	rowInfoCounter	Integer32
	rowInfoIndexNext	Integer32
	rowInfoMaxNoOfRows	Integer32

AgnFunctionEntry
SEQUENCE
	agnFunction	INTEGER
	agnFunctionActivation	INTEGER

AlarmForwardingEntry
SEQUENCE
	alarmForwardingFailPort	Integer32
	alarmForwardingToPort	Integer32
	alarmForwardingRowStatus	RowStatus
	alarmForwardingRecoveryTime	Integer32
	alarmForwardingGroupConditions	Integer32
	alarmForwardingCause	BITS
	alarmForwardingRecoveryMode	INTEGER
	alarmForwardingRecoveryCommand	INTEGER
	alarmForwardingDelay	Unsigned32
	alarmForwardingDirection	INTEGER
	alarmForwardingAction	BITS

AgnClkSrcPortEntry
SEQUENCE
	agnClkSrcPortCnfgIdx	Integer32
	agnClkSrcPortSrcIdx	INTEGER
	agnClkSrcPortIdx	Integer32
	agnClkSrcPort	Integer32
	agnClkSrcPortRowStatus	RowStatus
	agnClkSrcPortAdminStatus	INTEGER
	agnClkSrcPortType	INTEGER
	agnClkSrcPortQuality	INTEGER
	agnClkSrcPortNetType	INTEGER
	agnClkSrcPortState	INTEGER

AgnCurrClkEntry
SEQUENCE
	agnCurrClkObjIdx	Integer32
	agnCurrClkMode	INTEGER
	agnCurrClkSrc	INTEGER
	agnCurrClkPort	Integer32
	agnCurrClkHoldover	INTEGER
	agnCurrClkSsmBased	INTEGER
	agnCurrClkState	INTEGER
	agnCurrClkQualification	INTEGER

AgnClkCurrentEntry
SEQUENCE
	agnClkCurrentIndex	Unsigned32
	agnClkCurrentRxPackets	Gauge32
	agnClkCurrentLostPackets	Gauge32
	agnClkCurrentOutOfOrderPackets	Gauge32
	agnClkCurrentBufferUnderflow	Gauge32

AgnClkIntervalEntry
SEQUENCE
	agnClkIntervalIndex	Unsigned32
	agnClkIntervalNumber	Unsigned32
	agnClkIntervalRxPackets	Gauge32
	agnClkIntervalLostPackets	Gauge32
	agnClkIntervalOutOfOrderPackets	Gauge32
	agnClkIntervalBufferUnderflow	Gauge32

LagEntry
SEQUENCE
	lagCnfgIdx	Unsigned32
	lagIdx	Unsigned32
	lagPortMembers	PortList
	lagDistributionMethod	INTEGER
	lagRecoveryMode	INTEGER
	lagWaitToRestore	Unsigned32
	lagRowStatus	RowStatus
	lagShutDownDurationUponFlip	Unsigned32
	lagRdnMethod	INTEGER
	lagLacpEnable	INTEGER

LagStatEntry
SEQUENCE
	lagStatForcePort	Unsigned32
	lagStatActivePort	Unsigned32

GfpCnfgEntry
SEQUENCE
	gfpCnfgIdx	Unsigned32
	gfpPayloadFcs	INTEGER
	gfpRxTxScramble	INTEGER
	gfpVcatHeader	INTEGER

AgnGroupEntry
SEQUENCE
	agnGroupCnfgIdx	Unsigned32
	agnGroupIdx	Unsigned32
	agnGroupComponentIdx	Unsigned32
	agnGroupRowStatus	RowStatus

AgnStringToIndexEntry
SEQUENCE
	agnStringToIndexTableId	OBJECT IDENTIFIER
	agnStringToIndexUserName	SnmpAdminString
	agnStringToIndexTableIndex	Unsigned32

AgnRowPointerEntry
SEQUENCE
	agnRowPointerIndex	OBJECT IDENTIFIER
	agnRowPointerNoOfUsages	Unsigned32

RadTransportAddressType
A value that represents a transport domain. This is the enumerated version of the transport domain registrations in this MIB module. It was added in RAD MIB due to the fact that it is not defined in Standard MIB. The enumerated values have the following meaning: unknown(0) unknown transport address type efmOam (1) radTransportDomainSnmpEfmOam This textual convention can be used to represent transport domains in situations where a syntax of TransportDomain is unwieldy (for example, when used as an index). The usage of this textual convention implies that additional transport domains can only be supported by updating this MIB module.
TEXTUAL-CONVENTION
	INTEGER	unknown(0), efmOam(1)

RadTransportAddressEfmOam
Represents a transport address consisting of an EFM OAM port number.
TEXTUAL-CONVENTION
	OCTET STRING	Size(4)

RadBridgeMaskEntry
SEQUENCE
	radBridgeMaskType	INTEGER
	radBridgeMaskIfIndex	Integer32
	radBridgeMaskNum	Integer32
	radBridgeMaskDest	INTEGER
	radBridgeMaskPat1	OCTET STRING
	radBridgeMaskActiveBit1	OCTET STRING
	radBridgeMaskFrom1	INTEGER
	radBridgeMaskOffset1	Integer32
	radBridgeMaskCond1	INTEGER
	radBridgeMaskPat2	OCTET STRING
	radBridgeMaskActiveBit2	OCTET STRING
	radBridgeMaskFrom2	INTEGER
	radBridgeMaskOffset2	Integer32
	radBridgeMaskCond2	INTEGER
	radBridgeMaskPat3	OCTET STRING
	radBridgeMaskActiveBit3	OCTET STRING
	radBridgeMaskFrom3	INTEGER
	radBridgeMaskOffset3	Integer32
	radBridgeMaskCond3	INTEGER
	radBridgeMaskOper	INTEGER

RadBridgeCODEntry
SEQUENCE
	radBridgeCODIfIndex	Integer32
	radBridgeCODManualConnect	INTEGER
	radBridgeCODMode	INTEGER
	radBridgeCODConnectDelay	Integer32
	radBridgeCODisConnectDelay	Integer32
	radBridgeCODImplicitSwitch	INTEGER
	radBridgeCODNumAccess	Counter32
	radBridgeCODTotalConnecTime	Integer32

RadBridgeCODTimeTriggerEntry
SEQUENCE
	radBridgeCODTimeIfIndex	Integer32
	radBridgeCODDay	INTEGER
	radBridgeCODTimeTriggerNum	Integer32
	radBridgeCODTimeTriggerFrom	DisplayString
	radBridgeCODTimeTriggerTo	DisplayString
	radBridgeCODTimeTriggerStatus	INTEGER

RadBridgeCODTrafficEntry
SEQUENCE
	radBridgeCODProtocolType	INTEGER
	radBridgeCODTrafficTriggerStatus	INTEGER

RadBridgeCODCondEntry
SEQUENCE
	radBridgeCODCondIfIndex	Integer32
	radBridgeCODOriginateConnectCondition	INTEGER
	radBridgeCODOriginateDisConnectCondition	INTEGER
	radBridgeCODOriginateDisConnectDelay	Integer32
	radBridgeCODAnswerConnectCondition	INTEGER
	radBridgeCODSpecificOnTrafficOIDCondition	OBJECT IDENTIFIER
	radBridgeCODDisConnectMinimunFramesNumber	Integer32

RadBridgeIPXRipTableEntry
SEQUENCE
	radBridgeIPXRipDestNetwork	OCTET STRING
	radBridgeIPXRipPolicy	INTEGER
	radBridgeIPXRipForwardingRouter	OCTET STRING
	radBridgeIPXRipNIC	Integer32
	radBridgeIPXRipTickMetric	Integer32
	radBridgeIPXRipHopMetric	Integer32
	radBridgeIPXRipAgingTime	TimeTicks
	radBridgeIPXRipValueStatus	INTEGER
	radBridgeIPXRipForwardType	INTEGER

RadBridgeIPXRipInfEntry
SEQUENCE
	radBridgeIPXRipInfIfIndex	Integer32
	radBridgeIPXRipInfBcastUpdate	Integer32
	radBridgeIPXRipInfAgeMultiplier	Integer32

RadBridgeIPXSapTableEntry
SEQUENCE
	radBridgeIPXSapServerType	Integer32
	radBridgeIPXSapName	DisplayString
	radBridgeIPXSapNetwork	OCTET STRING
	radBridgeIPXSapNode	OCTET STRING
	radBridgeIPXSapSocket	Integer32
	radBridgeIPXSapHopsToServer	Integer32
	radBridgeIPXSapNIC	Integer32
	radBridgeIPXSapAgingTime	TimeTicks
	radBridgeIPXSapStatus	INTEGER

RadBridgeIPXSapInfEntry
SEQUENCE
	radBridgeIPXSapInfIfIndex	Integer32
	radBridgeIPXSapInfBcastUpdate	Integer32
	radBridgeIPXSapInfAgeMultiplier	Integer32

GenAddress
OCTET STRING	Size(12)

MaskingEntry
SEQUENCE
	maskingType	INTEGER
	maskingIfIndex	Integer32
	maskingIndex	Integer32
	maskingProtocolType	INTEGER
	maskingSmartMaskOID	OBJECT IDENTIFIER
	maskingFrameType	INTEGER
	maskingFrameTypeCondition	INTEGER
	maskingSourceAddress	GenAddress
	maskingSourceActiveBits	GenAddress
	maskingSourceMacOrNet	INTEGER
	maskingSourceCondition	INTEGER
	maskingDestAddress	GenAddress
	maskingDestActiveBits	GenAddress
	maskingDestMacOrNet	INTEGER
	maskingDestCondition	INTEGER
	maskingLowLevelProt	INTEGER
	maskingLowLevelProtCondition	INTEGER
	maskingHighLevelProt	Integer32
	maskingHighLevelProtCondition	INTEGER
	maskingPortNum	Integer32
	maskingPortNumCondition	INTEGER
	maskingOperation	INTEGER
	maskingSrcPortNum	Integer32
	maskingSrcPortNumCondition	INTEGER

RadBridgeCurrentEntry
SEQUENCE
	radBridgeCurrentIndex	Integer32
	radBridgeCurrentIngressFilteringDiscardedFrames	Gauge32
	radBridgeCurrentFrameTypeDiscardedFrames	Gauge32
	radBridgeCurrentRxCorrectFrames	Gauge32
	radBridgeCurrentRxCorrectBytes	Gauge32
	radBridgeCurrentRxCorrectBytesHCOverflow	Gauge32
	radBridgeCurrentRxBcastFrames	Gauge32
	radBridgeCurrentRxMcastFrames	Gauge32
	radBridgeCurrentTxCorrectFrames	Gauge32
	radBridgeCurrentTxCorrectBytes	Gauge32
	radBridgeCurrentTxCorrectBytesHCOverflow	Gauge32
	radBridgeCurrentTxBcastFrames	Gauge32
	radBridgeCurrentTxMcastFrames	Gauge32
	radBridgeCurrentTxDropFrames	Gauge32

RadBridgeIntervalEntry
SEQUENCE
	radBridgeIntervalIndex	Integer32
	radBridgeIntervalNumber	Integer32
	radBridgeIntervalIngressFilteringDiscardedFrames	Gauge32
	radBridgeIntervalFrameTypeDiscardedFrames	Gauge32
	radBridgeIntervalRxCorrectFrames	Gauge32
	radBridgeIntervalRxCorrectBytes	Gauge32
	radBridgeIntervalRxCorrectBytesHCOverflow	Gauge32
	radBridgeIntervalRxBcastFrames	Gauge32
	radBridgeIntervalRxMcastFrames	Gauge32
	radBridgeIntervalTxCorrectFrames	Gauge32
	radBridgeIntervalTxCorrectBytes	Gauge32
	radBridgeIntervalTxCorrectBytesHCOverflow	Gauge32
	radBridgeIntervalTxBcastFrames	Gauge32
	radBridgeIntervalTxMcastFrames	Gauge32
	radBridgeIntervalTxDropFrames	Gauge32

RadBridgePortBaseVlanEntry
SEQUENCE
	radBridgePortBaseVlanCnfgIdx	Integer32
	radBridgePortBaseVlanIdx	Integer32
	radBridgePortBaseVlanName	SnmpAdminString
	radBridgePortBaseVlanEgressPorts	PortList
	radBridgePortBaseVlanVirtualGroups	PortList
	radBridgePortBaseVlanRowStatus	RowStatus
	radBridgePortBaseVlanMng	INTEGER

RadBridgePortVlanMemberEntry
SEQUENCE
	radBridgePortVlanMemberBridgeIdx	Integer32
	radBridgePortVlanMemberPortIdx	Integer32
	radBridgePortVlanMemberVlanId	Integer32
	radBridgePortVlanMemberRowStatus	RowStatus

RadBridgeGenFlowEntry
SEQUENCE
	radBridgeGenFlowCnfgIdx	Integer32
	radBridgeGenFlowIdx	Integer32
	radBridgeGenFlowRowStatus	RowStatus
	radBridgeGenFlowFloodOrBcastMaxRate	Integer32
	radBridgeGenFlowQosMode	INTEGER
	radBridgeGenFlowSchedulingMode	INTEGER
	radBridgeGenFlowBasicClassification	INTEGER
	radBridgeGenFlowMulticastTrafficClass	Integer32
	radBridgeGenFlowBroadcastTrafficClass	Integer32
	radBridgeGenFlowUnkownUnicastTrafficClass	Integer32

RadBridgeDot1qVlanStaticEntry
SEQUENCE
	radBridgeDot1qVlanTaggedPorts	PortList
	radBridgeDot1qVlanUnmodifiedPorts	PortList
	radBridgeDot1qVlanSplitHorizon	INTEGER

RadBridgeInvBasePortEntry
SEQUENCE
	radBridgeInvBasePortIfIndex	Integer32
	radBridgeInvBasePort	Integer32

RadBridgeStpCnfgEntry
SEQUENCE
	radBridgeStpCnfgIdx1	Integer32
	radBridgeStpCnfgIdx2	Integer32
	radBridgeStpCnfgForwardDelay	Timeout
	radBridgeStpCnfgMaxAge	Timeout
	radBridgeStpCnfgHelloTime	Timeout
	radBridgeStpCnfgPriority	Integer32
	radBridgeStpCnfgStpVersion	INTEGER

RadBridgeStpStatEntry
SEQUENCE
	radBridgeStpStatIdx	Integer32
	radBridgeStpStatForwardDelay	Timeout
	radBridgeStpStatMaxAge	Timeout
	radBridgeStpStatHelloTime	Timeout
	radBridgeStpStatDesignatedRoot	BridgeId
	radBridgeStpStatRootCost	Integer32

RadBridgePortCnfgEntry
SEQUENCE
	radBridgePortCnfgIdx	Integer32
	radBridgePortCnfgPrtIdx	Integer32
	radBridgePortCnfgMaxMacAddr	Integer32
	radBridgePortCnfgMngFlow	INTEGER
	radBridgePortCnfgMcastMode	INTEGER
	radBridgePortCnfgDefaultVpi	Integer32
	radBridgePortCnfgDefaultVci	Integer32
	radBridgePortCnfgStatVlanId	Integer32
	radBridgePortCnfgIngressMtu	Integer32
	radBridgePortCnfgEgressMtu	Integer32
	radBridgePortCnfgDot1x	INTEGER

RadDot1qPortVlanEntry
SEQUENCE
	radDot1qPortStacking	INTEGER
	radDot1qPortCopyOriginVlanPriority	INTEGER
	radDot1qPortDefaultVlanPriority	Integer32
	radDot1qPortTagStripping	INTEGER
	radDot1qPortEgressTagHandling	INTEGER
	radDot1qPortIngressTagHandling	INTEGER
	radDot1qPortReplaceVlanPriority	INTEGER
	radDot1qPortVlanEthType	Unsigned32
	radDot1qPortVlanCnodeLevel1Agent	INTEGER

RadBridgeGenCfgEntry
SEQUENCE
	radBridgeGenCfgIdx	Integer32
	radBridgeGenCfgIdx2	Integer32
	radBridgeGenCfgBridgeAction	INTEGER
	radBridgeAgingTimeSec	INTEGER
	radBridgeMngVlanId	Unsigned32
	radBridgeLoopDetectVlanId	Unsigned32
	radBridgeSplitHorizon	INTEGER
	radBridgeEthType	Unsigned32

AgnSAlrEntry
SEQUENCE
	agnSAlrIdx	Integer32
	agnSAlrCodeDescription	DisplayString
	agnSAlrCode	Integer32
	agnSAlrSeverity	INTEGER
	agnSAlrState	INTEGER
	agnSAlrCounter	Integer32
	agnSAlrMask	INTEGER
	agnSAlrInvert	INTEGER

AgnSErrListEntry
SEQUENCE
	agnSErrIdx	Integer32
	agnSErrDescription	DisplayString

AgnSCnfgEntry
SEQUENCE
	agnSEntryIdx	Integer32
	agnSEntryIsValid	INTEGER

AgnCClkSrcEntry
SEQUENCE
	agnCClkCnfgIdx	Integer32
	agnCClkSrcIdx	Integer32
	agnCClkSrcMode	INTEGER
	agnCClkSrcSlt	INTEGER
	agnCClkSrcPrt	Integer32

AgnCnfgDataEntry
SEQUENCE
	agnCnfgIdx	Integer32
	agnCnfgDesc	DisplayString
	agnCnfgUpdDate	DisplayString
	agnCnfgUpdTime	DisplayString
	agnCnfgUpdMnger	IpAddress

AgnCnfgAlrEntry
SEQUENCE
	agnCnfgAlrCode	Integer32
	agnCnfgAlrSlot	INTEGER
	agnCnfgAlrPort	Integer32
	agnCnfgAlrMask	INTEGER
	agnCnfgAlrInvert	INTEGER
	agnCnfgAlrFilter	INTEGER
	agnCnfgAlrFilterSet	Integer32
	agnCnfgAlrFilterReset	Integer32
	agnCnfgAlrSeverity	INTEGER

AgnCnfgAlrReportEntry
SEQUENCE
	agnCnfgAlrReportType	INTEGER
	agnCnfgAlrStartReportOn	INTEGER
	agnCnfgAlrStartReportOff	INTEGER

AgnCT1E1RingEntry
SEQUENCE
	agnCT1E1RingCnfgIdx	Integer32
	agnCT1E1RingPrimeSlot	INTEGER
	agnCT1E1RingPrimePort	Integer32
	agnCT1E1RingSecSlot	INTEGER
	agnCT1E1RingSecPort	Integer32
	agnCT1E1RingRecTime	Integer32
	agnCT1E1RingRowStatus	RowStatus
	agnCT1E1RingWTR	Unsigned32
	agnCT1E1RingDualFailDetection	INTEGER

AgnCBuMlEntry
SEQUENCE
	agnCBuMlCnfgIdx	Integer32
	agnCBuMlRole	INTEGER
	agnCBuMlType	INTEGER
	agnCBuMlDefaultGateway	IpAddress
	agnCBuMlSubnetMask	IpAddress
	agnCBuMlOamFrequency	Integer32
	agnCBuMlOamTimeoutCycles	Integer32
	agnCBuMlWaitToRestore	Unsigned32

AgnCQ50Entry
SEQUENCE
	agnCQ50CnfgIdx	Integer32
	agnCQ50StopCallsThresh	Integer32
	agnCQ50DiscardPktThresh	Integer32
	agnCQ50BlockNewModemVbdCallsThresh	Integer32
	agnCQ50BlockNewModemRelayCallsThresh	Integer32

AgnCmprEntry
SEQUENCE
	agnCmprTypIdx	Integer32
	agnCmprCnfgIdx	Integer32
	agnCmprVersion	Integer32
	agnCmprObj	OCTET STRING

AgnDlciCmprEntry
SEQUENCE
	agnDlciCmprCnfgIdx	Integer32
	agnDlciCmprVersion	Integer32
	agnDlciCmprDlciIdx	Integer32
	agnDlciCmprObj	OCTET STRING

AgnAlarmsCmprEntry
SEQUENCE
	agnAlarmsCmprVersion	Integer32
	agnAlarmsCmprAlarmIdx	Integer32
	agnAlarmsCmprObj	OCTET STRING

AgnAlrBufCmprEntry
SEQUENCE
	agnAlrBufCmprVersion	Integer32
	agnAlrBufCmprAlarmIdx	Integer32
	agnAlrBufCmprObj	OCTET STRING

AgnSCmprErrListEntry
SEQUENCE
	agnSCmprErrVersion	Integer32
	agnSCmprErrIdx	Integer32
	agnSCmprErrObj	OCTET STRING

AgnTsCmprEntry
SEQUENCE
	agnTsCmprVerIdx	Integer32
	agnTsCmprCnfgIdx	Integer32
	agnTsCmprSlotIdx	Integer32
	agnTsCmprPortIdx	Integer32
	agnTsCmprPduIdx	Integer32
	agnTsCmprData	OCTET STRING

AgnXCmprEntry
SEQUENCE
	agnXCmprTypIdx	Integer32
	agnXCmprVersion	Integer32
	agnXCmprIdx3	Integer32
	agnXCmprIdx4	Integer32
	agnXCmprIdx5	Integer32
	agnXCmprIdx6	Integer32
	agnXCmprIdx7	Integer32
	agnXCmprObj	OCTET STRING

AgnLinkMapEntry
SEQUENCE
	mapLinkId	Integer32
	mapLinkSltIdx	INTEGER
	mapLinkPrtIdx	INTEGER
	mapLinkStatus	INTEGER

AlrBufEntry
SEQUENCE
	alrBufIdx	Integer32
	alrBufDescription	DisplayString
	alrBufCode	Unsigned32
	alrBufSlot	INTEGER
	alrBufPort	Unsigned32
	alrBufSeverity	INTEGER
	alrBufState	INTEGER

AgnCAgendaEntry
SEQUENCE
	agnCAgendaCnfgIdx	INTEGER
	agnCAgendaDayIdx	INTEGER
	agnCAgendaDayCategory	INTEGER

AgnCFlipNetEventsEntry
SEQUENCE
	agnCFlipNetEventsCnfgIdx	INTEGER
	agnCFlipNetEventIdx	Integer32
	agnCFlipNetEventActive	INTEGER
	agnCFlipNetEventType	INTEGER
	agnCFlipNetEventNo	Integer32
	agnCFlipNetEventSlot	INTEGER
	agnCFlipNetEventPort	Integer32
	agnCFlipNetEventISD	Integer32
	agnCFlipNetEventOSD	Integer32
	agnCFlipNetEventDayType	INTEGER
	agnCFlipNetEventStartTime	DisplayString
	agnCFlipNetEventEndTime	DisplayString

AgnCFlipEntry
SEQUENCE
	agnCFlipCnfgIdx	INTEGER
	agnCFlipIdx	Integer32
	agnCFlipActive	INTEGER
	agnCFlipLogicalExp	DisplayString
	agnCFlipDbNo	Integer32
	agnCFlipDiscardDe	INTEGER

AgnListDecodingEntry
SEQUENCE
	agnListDecodingType	INTEGER
	agnListDecodingCode	Integer32
	agnListDecodingDescription	DisplayString
	agnListDecodingDefState	INTEGER
	agnListDecodingSeverity	INTEGER
	agnListDecodingAcmRelaySlt	INTEGER
	agnListDecodingAcmRelayPrt	INTEGER

AgnDlciEntry
SEQUENCE
	agnDlciCnfgIdx	Integer32
	agnDlciLSltIdx	INTEGER
	agnDlciLPrtIdx	Integer32
	agnDlciLIdx	Integer32
	agnDlciHSltIdx	INTEGER
	agnDlciHPrtIdx	Integer32
	agnDlciHIdx	Integer32
	agnDlciTxBc	INTEGER
	agnDlciTxBe	INTEGER
	agnDlciRxBc	INTEGER
	agnDlciRxBe	INTEGER
	agnDlciPriority	Integer32
	agnDlciStatus	INTEGER
	agnDlciSpoofing	INTEGER
	agnDlciFunnelEnable	INTEGER
	agnDlciRoutingProtocol	INTEGER
	agnDlciRowStatus	RowStatus

AgnVoiceSwConfEntry
SEQUENCE
	agnVoiceSwConfIdx	INTEGER
	agnVoiceSwConfZoneId	DisplayString
	agnVoiceSwConfNodeId	DisplayString
	agnVoiceSwConfNoOfHops	Integer32
	agnVoiceSwConfSidt	Integer32
	agnVoiceSwConfLidt	Integer32
	agnVoiceSwConfDialPlan	INTEGER

AgnVoiceSwConfRtEntry
SEQUENCE
	agnVoiceSwConfRtDbId	INTEGER
	agnVoiceSwConfRtIdx	Integer32
	agnVoiceSwConfRtDigits	DisplayString
	agnVoiceSwConfRtAction	INTEGER
	agnVoiceSwConfRtData	DisplayString
	agnVoiceSwConfRtSlot	INTEGER
	agnVoiceSwConfRtPort	Integer32
	agnVoiceSwConfRtDlci	Integer32
	agnVoiceSwConfRtRowStatus	RowStatus
	agnVoiceSwConfRtMaxCalls	Integer32
	agnVoiceSwConfRtPriority	Integer32

AgnVoiceSwConfHGEntry
SEQUENCE
	agnVoiceSwConfHGdbIdx	INTEGER
	agnVoiceSwConfHGIdx	Integer32
	agnVoiceSwConfHGConnect	INTEGER
	agnVoiceSwConfHGExt	Integer32
	agnVoiceSwConfHGExtString	SnmpAdminString
	agnVoiceSwConfHGUserParams	SnmpAdminString
	agnVoiceSwConfHGStatus	INTEGER

AgnSigProfileEntry
SEQUENCE
	agnSigProfileCnfgIdx	Integer32
	agnSigProfileIdx	Integer32
	agnSigProfileRxTx	INTEGER
	agnSigProfileABCD	OCTET STRING

AgnSigProfEntry
SEQUENCE
	agnSigProfCnfgIdx	Integer32
	agnSigProfIdx	Integer32
	agnSigProfName	DisplayString
	agnSigProfType	INTEGER

SystemVoiceEntry
SEQUENCE
	systemVoiceConfIdx	Integer32
	systemVoiceNationalTone	INTEGER
	systemVoicePacketRate	Unsigned32
	systemVoiceFaxSupport	INTEGER
	systemVoiceFaxRate	INTEGER
	systemVoiceModemSupport	INTEGER
	systemVoiceCoderAndRate	INTEGER
	systemVoiceEchoCanceler	INTEGER
	systemVoiceTxGain	Integer32
	systemVoiceDtmfRelayMethod	INTEGER
	systemVoiceDtmfRelayRxPayloadType	Unsigned32
	systemVoiceDtmfRelayPayloadTypeNeg	INTEGER
	systemVoiceDtmfRelayTxPayloadType	Unsigned32

SystemVoiceCoderEntry
SEQUENCE
	systemVoiceCoderConfIdx	Unsigned32
	systemVoiceCoderPriority	Unsigned32
	systemVoiceCoderCoderAndRate	INTEGER

MdlSInstEntry
SEQUENCE
	mdlSInstSltIdx	INTEGER
	mdlSInstCardType	INTEGER
	mdlSHwVersion	DisplayString
	mdlSSwVersion	DisplayString
	mdlSAlrStatus	INTEGER
	mdlSAlrStatusAll	INTEGER
	mdlSMaskedAlrStat	INTEGER
	mdlSMaskedAlrStatAll	INTEGER
	mdlSTstStatusAll	INTEGER
	mdlSClearAlrCmd	INTEGER
	mdlSClearAllAlrCmd	INTEGER
	mdlSTemperature	Integer32

MdlSAlrEntry
SEQUENCE
	mdlSAlrSltIdx	INTEGER
	mdlSAlrIdx	Integer32
	mdlSAlrCodeDescription	DisplayString
	mdlSAlrCode	Integer32
	mdlSAlrSeverity	INTEGER
	mdlSAlrState	INTEGER
	mdlSAlrCounter	Integer32
	mdlSAlrMask	INTEGER
	mdlSAlrInvert	INTEGER

MdlCPrgEntry
SEQUENCE
	mdlCCnfgIdx	Integer32
	mdlCSltIdx	INTEGER
	mdlCPrgCardType	INTEGER
	mdlCNoOfExternPrt	Integer32
	mdlCNoOfInternPrt	Integer32
	mdlCWorkMode	INTEGER
	mdlCDhcpClientEnable	INTEGER
	mdlCRdnExists	INTEGER
	mdlCInterfaces	OCTET STRING

MdlCmprEntry
SEQUENCE
	mdlCmprTypIdx	Integer32
	mdlCmprCnfgIdx	Integer32
	mdlCmprVersion	Integer32
	mdlCmprSltIdx	INTEGER
	mdlCmprObj	OCTET STRING

MdlAlarmsCmprEntry
SEQUENCE
	mdlAlarmsCmprVersion	Integer32
	mdlAlarmsCmprAlarmSlot	Integer32
	mdlAlarmsCmprAlarmIdx	Integer32
	mdlAlarmsCmprObj	OCTET STRING

PrtSInstEntry
SEQUENCE
	prtSInstSltIdx	INTEGER
	prtSInstPrtIdx	Integer32
	prtSInstPrtType	INTEGER
	prtSInstIfIndex	Integer32
	prtSActiveStatus	INTEGER
	prtSAlrStatus	INTEGER
	prtSMaskedAlrStat	INTEGER
	prtSClearAlrCmd	INTEGER
	prtSTestMask	Integer32
	prtSTstCmd	INTEGER
	prtSTstDuration	Integer32
	prtSBertClrCmd	INTEGER
	prtSBertTstRslt	Integer32
	prtSInterfaceType	DisplayString
	prtSParamStatus	OCTET STRING
	prtSTestMaskXp	OCTET STRING
	prtSRdnStatus	INTEGER

PrtSAlrEntry
SEQUENCE
	prtSAlrSltIdx	INTEGER
	prtSAlrPrtIdx	Integer32
	prtSAlrIdx	Integer32
	prtSAlrCodeDescription	DisplayString
	prtSAlrCode	Integer32
	prtSAlrSeverity	INTEGER
	prtSAlrState	INTEGER
	prtSAlrCounter	Integer32
	prtSAlrMask	INTEGER
	prtSAlrInvert	INTEGER
	prtSAlrCardType	INTEGER

PrtFrStatisEntry
SEQUENCE
	prtFrStatisSltIdx	INTEGER
	prtFrStatisPrtIdx	INTEGER
	prtFrStatisInvIdx	INTEGER
	prtFrTimeElapsed	Integer32
	prtFrRxTotalFrames	Counter32
	prtFrTxTotalFrames	Counter32
	prtFrRxTotalBytes	Counter32
	prtFrTxTotalBytes	Counter32
	prtFrRxMngFrames	Counter32
	prtFrTxMngFrames	Counter32
	prtFrRxDeFrames	Counter32
	prtFrTxDeFrames	Counter32
	prtFrRxDcrdCongDeFr	Counter32
	prtFrTxDcrdCongDeFr	Counter32
	prtFrRxDcrdCongAllFr	Counter32
	prtFrTxDcrdCongAllFr	Counter32
	prtFrRxFecn	Counter32
	prtFrTxFecn	Counter32
	prtFrRxBecn	Counter32
	prtFrTxBecn	Counter32
	prtFrRxBeViol	Counter32
	prtFrTxBeViol	Counter32
	prtFrRxBcViol	Counter32
	prtFrTxBcViol	Counter32

PrtCrStatisEntry
SEQUENCE
	prtCrStatisSltIdx	INTEGER
	prtCrStatisPrtIdx	INTEGER
	prtCrStatisInvIdx	INTEGER
	prtCrTimeElapsed	Integer32
	prtCrRxTotalCells	Counter32
	prtCrTxTotalCells	Counter32
	prtCrRxDataCells	Counter32
	prtCrTxDataCells	Counter32

PrtDlciStatisEntry
SEQUENCE
	prtDlciSltIdx	INTEGER
	prtDlciPrtIdx	INTEGER
	prtDlciIdx	Integer32
	prtDlciRxDeFrames	Counter32
	prtDlciTxDeFrames	Counter32
	prtDlciRxDcrdCongDeFr	Counter32
	prtDlciTxDcrdCongDeFr	Counter32
	prtDlciRxDcrdCongAllFr	Counter32
	prtDlciTxDcrdCongAllFr	Counter32
	prtDlciTxFecn	Counter32
	prtDlciTxBecn	Counter32
	prtDlciRxBeViol	Counter32
	prtDlciTxBeViol	Counter32
	prtDlciRxBcViol	Counter32
	prtDlciTxBcViol	Counter32

PrtT1FdlMsgEntry
SEQUENCE
	prtT1FdlMsgSltIdx	INTEGER
	prtT1FdlMsgPrtIdx	INTEGER
	prtT1FdlMsgFdlTxRx	INTEGER
	prtT1FdlMsg	OCTET STRING

PrtExTsSplitEntry
SEQUENCE
	prtExTsCnfgIdx	Integer32
	prtExTsSltIdx	INTEGER
	prtExTsPrtIdx	Integer32
	prtExTsIdx	Integer32
	prtExTsBit	Integer32
	prtExTsIConSlot	INTEGER
	prtExTsIConPrt	Integer32
	prtExTsBitTest	INTEGER
	prtExTsTxSignaling	OCTET STRING
	prtExTsRxSignaling	OCTET STRING
	prtExTsTxIoSignaling	OCTET STRING
	prtExTsRxIoSignaling	OCTET STRING

PrtAgendaBehaviourEntry
SEQUENCE
	prtAgendaBehaviourCnfgIdx	Integer32
	prtAgendaBehaviourSltIdx	Integer32
	prtAgendaBehaviourPrtIdx	Integer32
	prtAgendaBehaviourOnOff	INTEGER

PrtCnfgAgendaEntry
SEQUENCE
	prtCnfgAgendaCnfgIdx	Integer32
	prtCnfgAgendaSltIdx	Integer32
	prtCnfgAgendaPrtIdx	Integer32
	prtCnfgAgendaDayIdx	INTEGER
	prtCnfgAgendaSesId	Integer32
	prtCnfgAgendaFrom	Integer32
	prtCnfgAgendaTo	Integer32

PrtGenCnfgEntry
SEQUENCE
	prtGenCnfgIdx	Integer32
	prtGenCnfgSltIdx	INTEGER
	prtGenCnfgPrtIdx	Integer32
	prtGenCnfgLinkToSlot	INTEGER
	prtGenCnfgLinkToPort	Integer32
	prtGenCnfgPortId	Integer32
	prtGenCnfgBusConnection	INTEGER
	prtGenCnfgInbandMng	INTEGER
	prtGenCnfgInbandMngRoutProt	INTEGER
	prtGenCnfgProtectionMode	INTEGER
	prtGenCnfgConnect	INTEGER
	prtGenCnfgSignalingType	INTEGER

PrtCmprEntry
SEQUENCE
	prtCmprTypIdx	Integer32
	prtCmprCnfgIdx	Integer32
	prtCmprVersion	Integer32
	prtCmprSltIdx	INTEGER
	prtCmprPrtIdx	Integer32
	prtCmprObj	OCTET STRING
	prtCmprStatisticObj	OCTET STRING

PrtDlciCmprEntry
SEQUENCE
	prtDlciCmprCnfgIdx	Integer32
	prtDlciCmprVersion	Integer32
	prtDlciCmprSltIdx	INTEGER
	prtDlciCmprPrtIdx	INTEGER
	prtDlciCmprDlciIdx	Integer32
	prtDlciCmprObj	OCTET STRING

PrtAlarmsCmprEntry
SEQUENCE
	prtAlarmsCmprVersion	Integer32
	prtAlarmsCmprAlarmSlot	Integer32
	prtAlarmsCmprAlarmPort	Integer32
	prtAlarmsCmprAlarmIdx	Integer32
	prtAlarmsCmprObj	OCTET STRING

PrtSExHsfStatEntry
SEQUENCE
	prtSExHsfSltIdx	INTEGER
	prtSExHsfPrtIdx	INTEGER
	prtSExHsfInterfaceTyp	INTEGER
	prtSExHsfRts	INTEGER

PrtIsdnStatusEntry
SEQUENCE
	prtIsdnStatusDspMode	INTEGER
	prtIsdnStatusCallState	INTEGER
	prtIsdnStatusCallingNumber	DisplayString
	prtIsdnStatusCalledNumber	DisplayString
	prtIsdnStatusCalledIP	IpAddress
	prtIsdnStatusCallDirection	INTEGER

MdlPbxFramerCnfgEntry
SEQUENCE
	mdlPbxFraCnfgIdx	Integer32
	mdlPbxFraSltIdx	INTEGER
	mdlPbxFraEnhEcho	INTEGER
	mdlPbxFraTSGroupAss	INTEGER
	mdlPbxFraSignalMode	INTEGER
	mdlPbxFraSignalVector	OCTET STRING
	mdlPbxFraSignalMask	OCTET STRING
	mdlPbxFraFramerSlot	INTEGER
	mdlPbxFraSignaling	INTEGER
	mdlPbxFraTransSigTs	Integer32

MdlProtIpEntry
SEQUENCE
	mdlProtIpCnfgIdx	Integer32
	mdlProtIpSlotIdx	INTEGER
	mdlProtIpAddress	IpAddress
	mdlProtIpRowStatus	RowStatus

MdlStatEntry
SEQUENCE
	mdlStatSltIdx	INTEGER
	mdlStatHostIP	IpAddress
	mdlStatHostMask	IpAddress
	mdlStatDefaultGateway	IpAddress

PrtExClCnfgEntry
SEQUENCE
	prtExClCnfgIdx	Integer32
	prtExClSltIdx	INTEGER
	prtExClPrtIdx	INTEGER
	prtExClUsage	INTEGER
	prtExClRate	INTEGER
	prtExClDataBits	INTEGER
	prtExClParity	INTEGER
	prtExClStopBits	INTEGER
	prtExClRoutingProtocol	INTEGER
	prtExClEnabled	INTEGER

PrtExPh1MlCnfgEntry
SEQUENCE
	prtExPh1MlCnfgIdx	Integer32
	prtExPh1MlSltIdx	INTEGER
	prtExPh1MlPrtIdx	INTEGER
	prtExPh1MlConnect	INTEGER
	prtExPh1MlLineType	INTEGER
	prtExPh1MlLineCode	INTEGER
	prtExPh1MlLineLen	INTEGER
	prtExPh1MlRestoreTime	INTEGER
	prtExPh1MlTxGain	INTEGER
	prtExPh1MlRxSensitivity	INTEGER
	prtExPh1MlIdleCode	Integer32
	prtExPh1MlTdmTrunk	INTEGER
	prtExPh1MlClkMode	INTEGER
	prtExPh1MlMfClkSrcSlt	INTEGER
	prtExPh1MlMfClkSrcPrt	INTEGER
	prtExPh1MlFdlType	INTEGER
	prtExPh1MlInbandMng	INTEGER
	prtExPh1MlInbandMngRate	INTEGER
	prtExPh1MlRedundType	INTEGER
	prtExPh1MlRedundSlot	INTEGER
	prtExPh1MlRedundPort	INTEGER
	prtExPh1MlRedundRecTime	Integer32
	prtExPh1MlInbandMngRoutProt	INTEGER
	prtExPh1MlIfType	INTEGER
	prtExPh1MlMultiplier	INTEGER
	prtExPh1MlSupportedTS	Integer32
	prtExPh1MlImpedance	INTEGER
	prtExPh1MlQ50BwControl	INTEGER
	prtExPh1MlQ50SignalPair	INTEGER
	prtExPh1MlInternalSwitch	INTEGER
	prtExPh1MlSigService	INTEGER
	prtExPh1MlFragmentSize	Integer32

PrtExPh1MlTsEntry
SEQUENCE
	prtExPh1MlTsCnfgIdx	Integer32
	prtExPh1MlTsSltIdx	INTEGER
	prtExPh1MlTsPrtIdx	INTEGER
	prtExPh1MlTsIdx	Integer32
	prtExPh1MlTsIConSlot	INTEGER
	prtExPh1MlTsIConPrt	Integer32
	prtExPh1MlTsIConTs	Integer32
	prtExPh1MlTsExt	OBJECT IDENTIFIER
	prtExPh1MlTsTest	INTEGER
	prtExPh1MlTsType	INTEGER
	prtExPh1MlTsBundle	Integer32
	prtExPh1MlTsTestDuration	Integer32
	prtExPh1MlTsSubChType	INTEGER
	prtExPh1MlTsSubChMask	Integer32
	prtExPh1MlTsChRate	INTEGER
	prtExPh1MlTsByteReversal	INTEGER
	prtExPh1MlTsSigProfile	INTEGER

PrtInPh1MlCnfgEntry
SEQUENCE
	prtInPh1MlCnfgIdx	Integer32
	prtInPh1MlSltType	INTEGER
	prtInPh1MlPrtIdx	Integer32
	prtInPh1MlConnect	INTEGER
	prtInPh1MlRate	INTEGER
	prtInPh1MlProtocol	INTEGER
	prtInPh1MlConnectionTyp	INTEGER
	prtInPh1MlCongResponse	INTEGER
	prtInPh1MlCongLevel	Integer32
	prtInPh1MlTc	INTEGER
	prtInPh1MlFlowControl	INTEGER
	prtInPh1MlSegment	INTEGER
	prtInPh1MlFrMngProt	INTEGER
	prtInPh1MlEnqPeriod	Integer32
	prtInPh1MlFullRptPeriod	Integer32
	prtInPh1MlFrWindowSize	Integer32
	prtInPh1MlErrorsThreshold	Integer32
	prtInPh1MlMaxIdleTime	Integer32
	prtInPh1MlBearerCh	INTEGER
	prtInPh1MlAssociatedExCh	INTEGER
	prtInPh1MlClockEncoding	INTEGER
	prtInPh1MlMinSeparators	Integer32
	prtInPh1MlCcittCrc	INTEGER
	prtInPh1MlFrameSeparator	INTEGER

PrtInPh1MlDlciEntry
SEQUENCE
	prtInPh1MlDlciCnfgIdx	Integer32
	prtInPh1MlDlciSltIdx	INTEGER
	prtInPh1MlDlciPrtIdx	INTEGER
	prtInPh1MlDlciIdx	Integer32
	prtInPh1MlDlciValid	INTEGER
	prtInPh1MlDlciIConSlt	INTEGER
	prtInPh1MlDlciIConPrt	INTEGER
	prtInPh1MlDlciIConDlci	Integer32
	prtInPh1MlDlciTxBc	INTEGER
	prtInPh1MlDlciTxBe	INTEGER
	prtInPh1MlDlciRxBc	INTEGER
	prtInPh1MlDlciRxBe	INTEGER
	prtInPh1MlDlciPriority	Integer32
	prtInPh1MlDlciStatus	INTEGER

PrtPhMlCnfgEntry
SEQUENCE
	prtPhMlCnfgIdx	Integer32
	prtPhMlSltIdx	INTEGER
	prtPhMlPrtIdx	INTEGER
	prtPhMlConnect	INTEGER
	prtPhMlRate	INTEGER
	prtPhMlCAS	INTEGER
	prtPhMlClockMode	INTEGER
	prtPhMlSatBuffer	INTEGER
	prtPhMlDialProcess	INTEGER
	prtPhMlSyncRestore	Integer32
	prtPhMlBus	INTEGER
	prtPhMlMfSyncSlot	INTEGER
	prtPhMlClockSource	INTEGER
	prtPhMlErrCorrection	INTEGER
	prtPhMlCorrectionMode	INTEGER
	prtPhMlControlSignals	INTEGER
	prtPhMlInterfaceType	INTEGER
	prtPhMlClockPolarity	INTEGER

PrtLogicalCnfgEntry
SEQUENCE
	prtLogicalCnfgIdx	Integer32
	prtLogicalSltIdx	INTEGER
	prtLogicalPrtIdx	Integer32
	prtLogicalConnect	INTEGER
	prtLogicalFunction	INTEGER
	prtLogicalRowStatus	RowStatus

LinkSelectorCnfgEntry
SEQUENCE
	linkSelectorCnfgIdx	Integer32
	linkSelectorSltIdx	INTEGER
	linkSelectorPrtIdx	Integer32
	linkSelectorMaxIdleTime	Integer32
	linkSelectorMode	INTEGER
	linkSelectorRevert	INTEGER
	linkSelectorMinBUSession	Integer32

LinkSelectorPLinkEntry
SEQUENCE
	pLinkCnfgIdx	Integer32
	pLinkSltIdx	INTEGER
	pLinkPrtIdx	Integer32
	pLinkIdx	Integer32
	pLinkSlotNu	INTEGER
	pLinkPortNu	Integer32
	pLinkPrioNu	Integer32
	pLinkVRate	INTEGER

PrtExPhPlCnfgEntry
SEQUENCE
	prtExPhPlCnfgIdx	Integer32
	prtExPhPlSltIdx	INTEGER
	prtExPhPlPrtIdx	INTEGER
	prtExPhPlConnect	INTEGER
	prtExPhPlHRate	INTEGER
	prtExPhPlLRate	INTEGER
	prtExPhPlProtocol	INTEGER
	prtExPhPlConnectionTyp	INTEGER
	prtExPhPlClkMode	INTEGER
	prtExPhPlDceClkSrc	INTEGER
	prtExPhPlCongResponse	INTEGER
	prtExPhPlCongLevel	Integer32
	prtExPhPlTc	INTEGER
	prtExPhPlFlowControl	INTEGER
	prtExPhPlDcdRts	INTEGER
	prtExPhPlDcdRtsControlPath	INTEGER
	prtExPhPlDataBits	INTEGER
	prtExPhPlParity	INTEGER
	prtExPhPlStopBits	INTEGER
	prtExPhPlLXon	Integer32
	prtExPhPlLXoff	Integer32
	prtExPhPlFrMngProt	INTEGER
	prtExPhPlEnqPeriod	Integer32
	prtExPhPlFullRptPeriod	Integer32
	prtExPhPlFrWindowSize	Integer32
	prtExPhPlErrorsThreshold	Integer32
	prtExPhPlPvcCreateMsg	INTEGER
	prtExPhPlCllmMsg	INTEGER
	prtExPhPlProtDelayLevel	INTEGER
	prtExPhPlClockEncoding	INTEGER
	prtExPhPlMinSeparators	Integer32
	prtExPhPlCcittCrc	INTEGER
	prtExPhPlFrameSeparator	INTEGER
	prtExPhPlIdleCode	Integer32
	prtExPhPlJitter	Integer32

PrtExPhPlDlciEntry
SEQUENCE
	prtExPhPlDlciCnfgIdx	Integer32
	prtExPhPlDlciSltIdx	INTEGER
	prtExPhPlDlciPrtIdx	INTEGER
	prtExPhPlDlciIdx	Integer32
	prtExPhPlDlciValid	INTEGER
	prtExPhPlDlciIConSlt	INTEGER
	prtExPhPlDlciIConPrt	INTEGER
	prtExPhPlDlciIConDlci	Integer32
	prtExPhPlDlciTxBc	INTEGER
	prtExPhPlDlciTxBe	INTEGER
	prtExPhPlDlciRxBc	INTEGER
	prtExPhPlDlciRxBe	INTEGER
	prtExPhPlDlciPriority	Integer32
	prtExPhPlDlciStatus	INTEGER

PrtExPhPlModemEntry
SEQUENCE
	prtExPhPlModemCnfgIdx	Integer32
	prtExPhPlModemSltIdx	INTEGER
	prtExPhPlModemPrtIdx	INTEGER
	prtExPhPlModemStatus	INTEGER
	prtExPhPlModemActivate	INTEGER
	prtExPhPlModemMaxIdleTime	Integer32
	prtExPhPlModemTimeBtwnCalls	Integer32
	prtExPhPlModemCallDelay	Integer32

PrtExLs2CnfgEntry
SEQUENCE
	prtExLs2CnfgIdx	Integer32
	prtExLs2SltIdx	INTEGER
	prtExLs2PrtIdx	INTEGER
	prtExLs2Connect	INTEGER
	prtExLs2Rate	INTEGER
	prtExLs2ClkMode	INTEGER
	prtExLs2Cts	INTEGER
	prtExLs2Dcd	INTEGER
	prtExLs2EnvIdx	Integer32

PrtInLs2CnfgEntry
SEQUENCE
	prtInLs2CnfgIdx	Integer32
	prtInLs2SltIdx	INTEGER
	prtInLs2PrtIdx	INTEGER
	prtInLs2Connect	INTEGER
	prtInLs2Group	Integer32
	prtInLs2Member	Integer32
	prtInLs2LinkTo	INTEGER
	prtInLs2EnvAssign	INTEGER

PrtVc2CnfgEntry
SEQUENCE
	prtVc2CnfgIdx	Integer32
	prtVc2SltIdx	INTEGER
	prtVc2PrtIdx	Integer32
	prtExVc2Connect	INTEGER
	prtExVc2TransGain	Integer32
	prtExVc2ReceiveGain	Integer32
	prtExVc2Wire	INTEGER
	prtExVc2CodingLaw	INTEGER
	prtExVc2Sig	INTEGER
	prtExVc2Oos	INTEGER
	prtExVc2LinkTo	INTEGER
	prtExVc2OperMode	INTEGER
	prtExVc2SigProfile	INTEGER
	prtExVc2CallEnable	INTEGER
	prtExVc2R2Delay	INTEGER
	prtExVc2CasStd	INTEGER
	prtExVc2EchoCanceler	INTEGER
	prtExVc2IfType	INTEGER
	prtExVc2Encoding	INTEGER
	prtExVc2TxBitCode	OCTET STRING
	prtExVc2RxBitOutput	OCTET STRING
	prtExVc2MeterRate	INTEGER
	prtExVc2IfSignaling	INTEGER
	prtExVc2SeizeAck	INTEGER
	prtExVc2EandMType	INTEGER
	prtExVc2RemType	INTEGER
	prtExVc2ConvTime	INTEGER
	prtExVc2SigFeedback	INTEGER
	prtExVc2EchoCancelerModule	INTEGER
	prtExVc2ReversePolarity	INTEGER
	prtExVc2RingerFrequency	INTEGER
	prtExVc2SigService	INTEGER
	prtExVc2CallerIdEnable	INTEGER
	prtExVc2CompressMethod	INTEGER
	prtExVc2ObMode	INTEGER
	prtExVc2VAD	INTEGER
	prtExVc2NoiseLevelForVAD	INTEGER
	prtExVc2WesternSigMode	INTEGER
	prtExVc2BusProtectionPoint	INTEGER
	prtExVc2ImpedanceStandard	INTEGER

PrtHsfCnfgEntry
SEQUENCE
	prtHsfCnfgIdx	Integer32
	prtHsfSltIdx	INTEGER
	prtHsfPrtIdx	INTEGER
	prtExHsfConnect	INTEGER
	prtExHsfRate	INTEGER
	prtExHsfClkMode	INTEGER
	prtExHsfCts	INTEGER
	prtExHsfFifoSize	INTEGER
	prtExHsfLinkTo	INTEGER
	prtExHsfOperMode	INTEGER
	prtExHsfInbandLoopback	INTEGER
	prtExHsfClkPolarity	INTEGER
	prtExHsfControlSignal	INTEGER
	prtExHsfBcastRingSrcPort	INTEGER

PrtExHs4CnfgEntry
SEQUENCE
	prtExHs4CnfgIdx	Integer32
	prtExHs4SltIdx	INTEGER
	prtExHs4PrtIdx	INTEGER
	prtExHs4Connect	INTEGER
	prtExHs4LineType	INTEGER
	prtExHs4LineCode	INTEGER
	prtExHs4LineLen	INTEGER
	prtExHs4RestoreT	INTEGER
	prtExHs4OosSig	INTEGER
	prtExHs4OosCode	INTEGER
	prtExHs4IdleCode	Integer32
	prtExHs4MfClkSrcSlt	INTEGER
	prtExHs4MfClkSrcPrt	INTEGER

PrtExHs4TsEntry
SEQUENCE
	prtExHs4TsCnfgIdx	Integer32
	prtExHs4TsSltIdx	INTEGER
	prtExHs4TsPrtIdx	INTEGER
	prtExHs4TsIdx	Integer32
	prtExHs4TsIConSlot	INTEGER
	prtExHs4TsIConPrt	INTEGER
	prtExHs4TsIConTs	Integer32

PrtExHsiCnfgEntry
SEQUENCE
	prtExHsiCnfgIdx	Integer32
	prtExHsiSltIdx	INTEGER
	prtExHsiPrtIdx	Integer32
	prtExHsiConnect	INTEGER
	prtExHsiRate	INTEGER
	prtExHsiLinkTo	INTEGER
	prtExHsiInterface	INTEGER
	prtExHsiActType	INTEGER

PrtInHsiCnfgEntry
SEQUENCE
	prtInHsiCnfgIdx	Integer32
	prtInHsiSltIdx	INTEGER
	prtInHsiPrtIdx	Integer32
	prtInHsiConnect	INTEGER
	prtInHsiRate	INTEGER
	prtInHsiConcentratedTo	Integer32

PrtExHsrCnfgEntry
SEQUENCE
	prtExHsrCnfgIdx	Integer32
	prtExHsrSltIdx	INTEGER
	prtExHsrPrtIdx	Integer32
	prtExHsrConnect	INTEGER
	prtExHsrProtocol	INTEGER
	prtExHsrRate	INTEGER
	prtExHsrDataBits	INTEGER
	prtExHsrParity	INTEGER
	prtExHsrStopBits	INTEGER
	prtExHsrCts	INTEGER
	prtExHsrClkMode	INTEGER
	prtExHsrLinkTo	INTEGER
	prtExHsrDcdDsr	INTEGER
	prtExHsrOperMode	INTEGER
	prtExHsrRtsDtr	INTEGER
	prtExHsrLlbEnable	INTEGER
	prtExHsrRlbEnable	INTEGER
	prtExHsrRateAdapt	INTEGER
	prtExHsrRemoteModem	INTEGER
	prtExHsrEncapsMode	INTEGER

PrtExMbeCnfgEntry
SEQUENCE
	prtExMbeCnfgIdx	Integer32
	prtExMbeSltIdx	INTEGER
	prtExMbePrtIdx	INTEGER
	prtExMbeLan	INTEGER

PrtInMbeCnfgEntry
SEQUENCE
	prtInMbeCnfgIdx	Integer32
	prtInMbeSltIdx	INTEGER
	prtInMbePrtIdx	INTEGER
	prtInMbeConnect	INTEGER
	prtInMbeRate	INTEGER
	prtInMbeLinkTo	INTEGER

PrtExTreCnfgEntry
SEQUENCE
	prtExTreCnfgIdx	Integer32
	prtExTreSltIdx	INTEGER
	prtExTrePrtIdx	INTEGER
	prtExTreLan	INTEGER
	prtExTreLanRate	INTEGER

PrtInTreCnfgEntry
SEQUENCE
	prtInTreCnfgIdx	Integer32
	prtInTreSltIdx	INTEGER
	prtInTrePrtIdx	INTEGER
	prtInTreConnect	INTEGER
	prtInTreRate	INTEGER
	prtInTreLinkTo	INTEGER

PrtExPVc4CnfgEntry
SEQUENCE
	prtExPVc4CnfgIdx	Integer32
	prtExPVc4SltIdx	INTEGER
	prtExPVc4PrtIdx	INTEGER
	prtExPVc4PrtType	INTEGER
	prtExPVc4Connect	INTEGER
	prtExPVc4IfType	INTEGER
	prtExPVc4TxGain	Integer32
	prtExPVc4RxGain	Integer32
	prtExPVc4MaxRate	INTEGER
	prtExPVc4Tc	INTEGER
	prtExPVc4Oos	INTEGER
	prtExPVc4EchoCanceler	INTEGER
	prtExPVc4VarDelay	Integer32
	prtExPVc4CongLevel	Integer32
	prtExPVc4Wire	INTEGER
	prtExPVc4ExtensionType	INTEGER
	prtExPVc4ExtensionNumber	DisplayString
	prtExPVc4OutPulsing	INTEGER
	prtExPVc4HuntGroupMb	INTEGER
	prtExPVc4HuntGroupIdx	Integer32
	prtExPVc4AutoFaxMode	INTEGER
	prtExPVc4FaxRate	INTEGER
	prtExPVc4SeizeAck	INTEGER
	prtExPVc4SignalingProtocol	INTEGER
	prtExPVc4DelayStart	Integer32
	prtExPVc4WinkMinDuration	Integer32
	prtExPVc4WinkMaxDuration	Integer32
	prtExPVc4GenerateTone	INTEGER
	prtExPVc4CodingLaw	INTEGER
	prtExPVc4GenerateRingBack	INTEGER
	prtExPVc4ChannelId	Integer32
	prtExPVc4PortConnection	INTEGER
	prtExPVc4CoderAndRate	INTEGER
	prtExPVc4DestinationNum	DisplayString
	prtExPVc4DtmfRelay	INTEGER
	prtExPVc4DiscOnSilence	Integer32
	prtExPVc4DynamicJitter	INTEGER
	prtExPVc4EandMType	INTEGER
	prtExPVc4Rate	Integer32
	prtExPVc4FrameSize	Integer32
	prtExPVc4MultiplexInterval	Integer32
	prtExPVc4TransportProtocol	INTEGER
	prtExPVc4MultiFreqRelay	INTEGER
	prtExPVc4MinPulseWidth	Integer32
	prtExPVc4MinPowerLevel	Integer32
	prtExPVc4SuperTandem	INTEGER
	prtExPVc4DestIp	IpAddress
	prtExPVc4DestBundle	Integer32
	prtExPVc4SrcIpAddress	IpAddress
	prtExPVc4SrcIpMask	IpAddress
	prtExPVc4DefaultGateway	IpAddress
	prtExPVc4SigPacketInterval	Unsigned32

PrtExPVc4DlciEntry
SEQUENCE
	prtExPVc4DlciCnfgIdx	Integer32
	prtExPVc4DlciSltIdx	INTEGER
	prtExPVc4DlciPrtIdx	INTEGER
	prtExPVc4DlciValid	INTEGER
	prtExPVc4DlciIConSlt	INTEGER
	prtExPVc4DlciIConPrt	INTEGER
	prtExPVc4DlciIConDlci	Integer32
	prtExPVc4DlciTxBc	INTEGER
	prtExPVc4DlciTxBe	INTEGER
	prtExPVc4DlciRxBc	INTEGER
	prtExPVc4DlciRxBe	INTEGER
	prtExPVc4DlciPriority	Integer32
	prtExPVc4DlciStatus	INTEGER

PrtExLs6CnfgEntry
SEQUENCE
	prtExLs6CnfgIdx	Integer32
	prtExLs6SltIdx	INTEGER
	prtExLs6PrtIdx	INTEGER
	prtExLs6Connect	INTEGER
	prtExLs6Protocol	INTEGER
	prtExLs6Rate	INTEGER
	prtExLs6ClkMode	INTEGER
	prtExLs6CtrlSignal	INTEGER
	prtExLs6DataBits	INTEGER
	prtExLs6Cts	INTEGER
	prtExLs6LinkToInternal	INTEGER

PrtExLs6VCnfgEntry
SEQUENCE
	prtExLs6VCnfgIdx	Integer32
	prtExLs6VSltIdx	INTEGER
	prtExLs6VPrtIdx	INTEGER
	prtExLs6VConnect	INTEGER
	prtExLs6VRate	INTEGER
	prtExLs6VEchoCanceler	INTEGER
	prtExLs6VIfType	INTEGER
	prtExLs6VTxGain	Integer32
	prtExLs6VRxGain	Integer32
	prtExLs6VOos	INTEGER

PrtInLs6CnfgEntry
SEQUENCE
	prtInLs6CnfgIdx	Integer32
	prtInLs6SltIdx	INTEGER
	prtInLs6PrtIdx	INTEGER
	prtInLs6Connect	INTEGER
	prtInLs6TandemMode	INTEGER
	prtInLs6Rate	INTEGER
	prtInLs6RemoteType	INTEGER
	prtInLs6LinkTo	INTEGER

PrtExVc3CnfgEntry
SEQUENCE
	prtExVc3CnfgIdx	Integer32
	prtExVc3SltIdx	INTEGER
	prtExVc3PrtIdx	INTEGER
	prtExVc3Connect	INTEGER
	prtExVc3TransGain	Integer32
	prtExVc3ReceiveGain	Integer32
	prtExVc3Wire	INTEGER
	prtExVc3Rate	INTEGER
	prtExVc3EchoCanceler	INTEGER

PrtInVc3CnfgEntry
SEQUENCE
	prtInVc3CnfgIdx	Integer32
	prtInVc3SltIdx	INTEGER
	prtInVc3PrtIdx	INTEGER
	prtInVc3Connect	INTEGER
	prtInVc3Rate	INTEGER
	prtInVc3Oos	INTEGER
	prtInVc3LinkTo	INTEGER

PrtExVcPbxCnfgEntry
SEQUENCE
	prtExVcPbxCnfgIdx	Integer32
	prtExVcPbxSltIdx	INTEGER
	prtExVcPbxPrtIdx	INTEGER
	prtExVcPbxConnect	INTEGER
	prtExVcPbxGroup	INTEGER
	prtExVcPbxTransparent	INTEGER
	prtExVcPbxTransSignalTs	Integer32
	prtExVcPbxFrame	INTEGER
	prtExVcPbxRestoreTime	INTEGER
	prtExVcPbxLineCode	INTEGER
	prtExVcPbxLineLength	INTEGER
	prtExVcPbxLinkTo	INTEGER
	prtExVcPbxSignalOper	INTEGER
	prtExVcPbxIdleCode	INTEGER

PrtIn1p6VcPbxCnfgEntry
SEQUENCE
	prtIn1p6VcPbxCnfgIdx	Integer32
	prtIn1p6VcPbxSltIdx	INTEGER
	prtIn1p6VcPbxPrtIdx	INTEGER
	prtIn1p6VcPbxConnect	INTEGER
	prtIn1p6VcPbxRate	INTEGER
	prtIn1p6VcPbxEchoCanceler	INTEGER
	prtIn1p6VcPbxPabxTs	Integer32

PrtIn7p8VcPbxCnfgEntry
SEQUENCE
	prtIn7p8VcPbxCnfgIdx	Integer32
	prtIn7p8VcPbxSltIdx	INTEGER
	prtIn7p8VcPbxPrtIdx	INTEGER
	prtIn7p8VcPbxConnect	INTEGER
	prtIn7p8VcPbxMode	INTEGER
	prtIn7p8VcPbxRate	INTEGER
	prtIn7p8VcPbxSignalMode	INTEGER
	prtIn7p8VcPbxOos	INTEGER
	prtIn7p8VcPbxLinkTo	INTEGER

PrtExVcPbxTsEntry
SEQUENCE
	prtExVcPbxTsCnfgIdx	Integer32
	prtExVcPbxTsSltIdx	INTEGER
	prtExVcPbxTsPrtIdx	INTEGER
	prtExVcPbxTsIdx	Integer32
	prtExVcPbxTsMode	INTEGER
	prtExVcPbxTsIConSlot	INTEGER
	prtExVcPbxTsIConPrt	INTEGER
	prtExVcPbxTsIConTs	Integer32
	prtExVcPbxTsRemPrt	INTEGER
	prtExVcPbxTsRemTs	Integer32
	prtExVcPbxTsRemConnID	Unsigned32
	prtExVcPbxTsSourceSlot	INTEGER
	prtExVcPbxTsSourcePrt	Unsigned32

PrtIsdnCnfgEntry
SEQUENCE
	prtIsdnCnfgIdx	Integer32
	prtIsdnSltIdx	INTEGER
	prtIsdnPrtIdx	Integer32
	prtIsdnConnect	INTEGER
	prtIsdnSignalingProtocol	INTEGER
	prtIsdnBasicRateLineTopology	INTEGER
	prtIsdnMode	INTEGER
	prtIsdnFilter	INTEGER
	prtIsdnSimultaneousCall	INTEGER
	prtIsdnNumOfAbstractTerm	Integer32
	prtIsdnSwitchMode	INTEGER
	prtIsdnAbSide	INTEGER
	prtIsdnQsigRole	INTEGER
	prtIsdnInterface	INTEGER
	prtIsdnCallMode	INTEGER
	prtIsdnCallBackTimeout	Integer32

PrtIsdnEndpointEntry
SEQUENCE
	prtIsdnEndpointCnfgIdx	Integer32
	prtIsdnEndpointSltIdx	INTEGER
	prtIsdnEndpointPrtIdx	Integer32
	prtIsdnEndpointIdx	INTEGER
	prtIsdnEndpointTeiType	INTEGER
	prtIsdnEndpointTeiValue	Integer32
	prtIsdnEndpointSpid	DisplayString
	prtIsdnEndpointBearerCh	INTEGER
	prtIsdnEndpointRowStatus	RowStatus

PrtIsdnDirectoryEntry
SEQUENCE
	prtIsdnDirectoryCnfgIdx	Integer32
	prtIsdnDirectorySltIdx	INTEGER
	prtIsdnDirectoryPrtIdx	Integer32
	prtIsdnDirectoryLocalAddr	DisplayString
	prtIsdnDirectoryLocalSubAddr	DisplayString
	prtIsdnDirectoryRemoteAddr	DisplayString
	prtIsdnDirectoryRemoteSubAddr	DisplayString
	prtIsdnDirectoryPrtNu	Integer32
	prtIsdnDirectoryTeiId	Integer32
	prtIsdnDirectoryRowStatus	RowStatus
	prtIsdnDirectoryLocalAddr2	DisplayString
	prtIsdnDirectoryLocalSubAddr2	DisplayString
	prtIsdnDirectoryRemoteAddr2	DisplayString
	prtIsdnDirectoryRemoteSubAddr2	DisplayString

PrtFrPlusCnfgEntry
SEQUENCE
	prtFrPlusCnfgIdx	Integer32
	prtFrPlusSltIdx	INTEGER
	prtFrPlusPrtIdx	Integer32
	prtFrPlusNotSegmentedPriorities	OCTET STRING

PrtMl4CnfgEntry
SEQUENCE
	prtMl4CnfgIdx	Integer32
	prtMl4SltIdx	INTEGER
	prtMl4PrtIdx	INTEGER
	prtMl4SigProfile	INTEGER
	prtMl4CGA	INTEGER
	prtMl4Oos	INTEGER
	prtMl4VoiceOos	OCTET STRING
	prtMl4DataOos	OCTET STRING
	prtMl4Service	INTEGER
	prtMl4IpAddress	IpAddress
	prtMl4IpMask	IpAddress
	prtMl4SignalingMode	INTEGER
	prtMl4EchoCanceler	INTEGER
	prtMl4OosErrorSource	INTEGER
	prtMl4OosEntryThreshold	Integer32
	prtMl4OosExitThreshold	Integer32
	prtMl4LogicalLinkId	Integer32
	prtMl4DedicatedTs	Integer32
	prtMl4RemCrc	INTEGER
	prtMl4CrossConnectLevel	INTEGER
	prtMl4PppEchoFailDetection	INTEGER

PrtAcmCnfgEntry
SEQUENCE
	prtAcmCnfgIdx	Integer32
	prtAcmSltIdx	INTEGER
	prtAcmPrtIdx	INTEGER
	prtAcmConnect	INTEGER
	prtAcmActiveState	INTEGER
	prtAcmAlrString	DisplayString

PrtE2CnfgEntry
SEQUENCE
	prtE2CnfgIdx	Integer32
	prtE2SltIdx	INTEGER
	prtE2PrtIdx	INTEGER
	prtE2Connect	INTEGER
	prtE2MngOnNationalBit	INTEGER

PrtLanWanCnfgEntry
SEQUENCE
	prtLanWanCnfgIdx	Integer32
	prtLanWanSltIdx	INTEGER
	prtLanWanPrtIdx	Integer32
	prtLanWanMode	INTEGER
	prtLanWanDestIf	Integer32
	prtLanWanEgressVlanMode	INTEGER
	prtLanWanL2Protocol	INTEGER
	prtLanWanStpPriority	Integer32
	prtLanWanStpCost	Integer32
	prtLanWanToLanVlanMode	INTEGER
	prtLanWanVlanId	Integer32
	prtLanWanVlanPriority	Integer32
	prtLanWanMtu	Integer32
	prtLanWanVlanType	INTEGER

Dsx1XCurrentEntry
SEQUENCE
	dsx1CurrentLOS	PerfCurrentCount
	dsx1CurrentLOF	PerfCurrentCount
	dsx1CurrentLOC	PerfCurrentCount
	dsx1CurrentAIS	PerfCurrentCount
	dsx1CurrentRAI	PerfCurrentCount
	dsx1CurrentLOMF	PerfCurrentCount
	dsx1CurrentFEBE	PerfCurrentCount
	dsx1CurrentStatus	OCTET STRING
	dsx1CurrentBPV	PerfCurrentCount
	dsx1CurrentLOCRCMF	PerfCurrentCount
	dsx1CurrentLOFC	PerfCurrentCount
	dsx1CurrentCRCErrors	PerfCurrentCount

Dsx1XIntervalEntry
SEQUENCE
	dsx1IntervalLOS	PerfIntervalCount
	dsx1IntervalLOF	PerfIntervalCount
	dsx1IntervalLOC	PerfIntervalCount
	dsx1IntervalAIS	PerfIntervalCount
	dsx1IntervalRAI	PerfIntervalCount
	dsx1IntervalLOMF	PerfIntervalCount
	dsx1IntervalFEBE	PerfIntervalCount
	dsx1IntervalStatus	OCTET STRING
	dsx1IntervalBPV	PerfIntervalCount
	dsx1IntervalLOCRCMF	PerfIntervalCount
	dsx1IntervalLOFC	PerfIntervalCount

Dsx1XTotalEntry
SEQUENCE
	dsx1TotalLOS	PerfTotalCount
	dsx1TotalBPV	PerfTotalCount
	dsx1TotalLOFC	PerfTotalCount

Dsx1DataStreamStatEntry
SEQUENCE
	dsx1DataStreamStatIfIndex	Integer32
	dsx1DataStreamStatIndex	Integer32
	dsx1DataStreamStatValid	TruthValue
	dsx1DataStreamStatInFrames	Counter32
	dsx1DataStreamStatInBytes	Counter32
	dsx1DataStreamStatInDiscards	Counter32
	dsx1DataStreamStatInErrors	Counter32
	dsx1DataStreamStatOutFrames	Counter32
	dsx1DataStreamStatOutBytes	Counter32
	dsx1DataStreamStatOutDiscards	Counter32
	dsx1DataStreamStatOutErrors	Counter32

Dsx1XConfigEntry
SEQUENCE
	dsx1IdleCode	Integer32
	dsx1LineMode	INTEGER
	dsx1dBTxGain	INTEGER
	dsx1RxSensitivity	INTEGER
	dsx1RestoreTime	INTEGER
	dsx1TcFirstSignal	Integer32
	dsx1TcSignal	Integer32
	dsx1TcPattern	Integer32
	dsx1Scramble	INTEGER
	dsx1LineAdaptiveTimingMode	INTEGER
	dsx1TxClockSource	INTEGER
	dsx1AisEnable	INTEGER
	dsx1TsEchoCancel	OCTET STRING
	dsx1EchoCancelerModule	INTEGER
	dsx1PortFunction	INTEGER
	dsx1PortMultiplier	INTEGER
	dsx1LeasedLine	INTEGER
	dsx1CsuLoop	INTEGER
	dsx1ClockSource	Integer32
	dsx1OosSignal	INTEGER
	dsx1BundleNextIndex	Integer32
	dsx1CRC6CalcMode	INTEGER
	dsx1SendUponFail	INTEGER

PrtDs3IfEntry
SEQUENCE
	prtDs3IfTimeElapsed	Integer32
	prtDs3IfValidIntervals	Integer32

PrtDs3CurrentEntry
SEQUENCE
	prtDs3CurrentLOS	Gauge32
	prtDs3CurrentOOF	Gauge32
	prtDs3CurrentLOC	Gauge32
	prtDs3CurrentAIS	Gauge32
	prtDs3CurrentRDI	Gauge32
	prtDs3CurrentUAS	Gauge32
	prtDs3CurrentBIP	Gauge32
	prtDs3CurrentFEBE	Gauge32
	prtDs3CurrentSLM	Gauge32
	prtDs3CurrentSES	Gauge32
	prtDs3CurrentES	Gauge32
	prtDs3CurrentBitParity	Gauge32
	prtDs3CurrentPlcpLOF	Gauge32
	prtDs3CurrentPlcpRAI	Gauge32
	prtDs3CurrentPlcpBIP	Gauge32
	prtDs3CurrentPlcpFEBE	Gauge32
	prtDs3CurrentBPV	Gauge32
	prtDs3CurrentLCE	Gauge32
	prtDs3CurrentStatus	OCTET STRING

PrtDs3IntervalEntry
SEQUENCE
	prtDs3IntervalNumber	Integer32
	prtDs3IntervalLOS	Gauge32
	prtDs3IntervalOOF	Gauge32
	prtDs3IntervalLOC	Gauge32
	prtDs3IntervalAIS	Gauge32
	prtDs3IntervalRDI	Gauge32
	prtDs3IntervalUAS	Gauge32
	prtDs3IntervalBIP	Gauge32
	prtDs3IntervalFEBE	Gauge32
	prtDs3IntervalSLM	Gauge32
	prtDs3IntervalSES	Gauge32
	prtDs3IntervalES	Gauge32
	prtDs3IntervalBitParity	Gauge32
	prtDs3IntervalPlcpLOF	Gauge32
	prtDs3IntervalPlcpRAI	Gauge32
	prtDs3IntervalPlcpBIP	Gauge32
	prtDs3IntervalPlcpFEBE	Gauge32
	prtDs3IntervalBPV	Gauge32
	prtDs3IntervalLCE	Gauge32
	prtDs3IntervalStatus	OCTET STRING

PrtDs3TotalEntry
SEQUENCE
	prtDs3TotalUAS	Gauge32
	prtDs3TotalBPV	Gauge32
	prtDs3TotalLCE	Gauge32
	prtDs3TotalSES	Gauge32

Dsx3XConfigEntry
SEQUENCE
	dsx3AisEnable	INTEGER
	dsx3TxClockSource	INTEGER

Dsx3MappingEntry
SEQUENCE
	dsx3MappingDs3Index	InterfaceIndex
	dsx3MappingNumber	Unsigned32
	dsx3MappingIfIndex	InterfaceIndex

AtmNteConfIfEntry
SEQUENCE
	atmConfIfTransmitClk	INTEGER
	atmConfIfLoopback	INTEGER
	atmConfIfFrameType	INTEGER
	atmConfIfCardType	INTEGER
	atmConfAtmIfVpiVciLimit	INTEGER
	atmConfIfHwFeatures	INTEGER
	atmConfIfOutputRate	Integer32
	atmConfIfInputRate	Integer32
	atmConfAlarmForwarding	INTEGER
	atmConfIfAllocatedBw	Integer32
	atmConfIfLowerVpi	Integer32
	atmConfIfOamMode	INTEGER
	atmConfIfOamFailureInd	INTEGER

AtmNteAlarmIfEntry
SEQUENCE
	atmInterfaceActiveAlarms	Integer32
	atmThresholdSectionBIP	Integer32
	atmThresholdLineBIP	Integer32
	atmThresholdLineFEBE	Integer32
	atmThresholdPathBIP	Integer32
	atmThresholdPathFEBE	Integer32
	atmThresholdErroredCells	Integer32
	atmThresholdLostCells	Integer32
	atmThresholdMisinsertedCells	Integer32
	atmInterfaceAlarmStatus	INTEGER
	atmInterfaceMaskAlarms	Integer32

AtmNteConfVpEntry
SEQUENCE
	atmConfVpPolicing	INTEGER
	atmConfVpCCAdminStatus	INTEGER
	atmConfVpLoopbackAdminStatus	INTEGER
	atmConfVpLoopbackSinkAddress	OCTET STRING
	atmConfVpCongestionControl	OCTET STRING
	atmConfVpCCDirection	INTEGER
	atmConfVpCreationTime	DateAndTime
	atmConfVpOamSupport	INTEGER
	atmConfVpCCOperStatus	INTEGER
	atmConfVpLoopbackTraffic	INTEGER
	atmConfVpLoopbackFailureInd	INTEGER
	atmConfVpLoopbackFailureThreshold	Integer32
	atmConfVpOamDirection	INTEGER
	atmConfVpOamDescrIndex	Integer32
	atmConfVpConnected	INTEGER

AtmNteAlarmVpEntry
SEQUENCE
	atmNteVpAlarmVpi	Integer32
	atmNteVpActiveAlarms	Integer32

AtmNteAlarmVcEntry
SEQUENCE
	atmNteVcAlarmVpi	Integer32
	atmNteVcAlarmVci	Integer32
	atmNteVcActiveAlarms	Integer32

AtmIfDataEntry
SEQUENCE
	atmIfTimeElapsed	Integer32
	atmIfValidIntervals	Integer32
	atmIfTxCells	Counter32
	atmIfRxCells	Counter32
	atmIfUncorrectedHecs	Counter32

AtmIfCurrentEntry
SEQUENCE
	atmIfCurrentTxCells	Gauge32
	atmIfCurrentRxCells	Gauge32
	atmIfCurrentCorrectedHecs	Gauge32
	atmIfCurrentUncorrectedHecs	Gauge32
	atmIfCurrentHecErrorSeconds	Gauge32

AtmIfIntervalEntry
SEQUENCE
	atmIfIntervalNumber	Integer32
	atmIfIntervalTxCells	Gauge32
	atmIfIntervalRxCells	Gauge32
	atmIfIntervalCorrectedHecs	Gauge32
	atmIfIntervalUncorrectedHecs	Gauge32
	atmIfIntervalHecErrorSeconds	Gauge32

AtmVpCurrentEntry
SEQUENCE
	atmVpCurrentVpi	Integer32
	atmVpCurrentRxCellsClp01	Gauge32
	atmVpCurrentRxCellsClp0	Gauge32
	atmVpCurrentGcra0Violations	Gauge32
	atmVpCurrentGcra1Violations	Gauge32
	atmVpCurrentRxAIS	Gauge32
	atmVpCurrentTxAIS	Gauge32
	atmVpCurrentRxRDI	Gauge32
	atmVpCurrentTxRDI	Gauge32
	atmVpCurrentContinuityLoss	Gauge32
	atmVpCurrentUAS	Gauge32
	atmVpCurrentSES	Gauge32
	atmVpCurrentCDC	Gauge32
	atmVpCurrentTotalDiscards	Gauge32
	atmVpCurrentClp0Discards	Gauge32
	atmVpCurrentTotalCellOuts	Gauge32
	atmVpCurrentClp0CellOuts	Gauge32
	atmVpCurrentTaggedOuts	Gauge32
	atmVpCurrentPCR	Gauge32
	atmVpCurrentSCR	Gauge32
	atmVpCurrentMCR	Gauge32
	atmVpCurrentShaperTotalDiscards	Gauge32
	atmVpCurrentShaperClp0Discards	Gauge32
	atmVpCurrentShaperClp1Discards	Gauge32

AtmVpPMCurrentEntry
SEQUENCE
	atmVpPMCurrentDir	INTEGER
	atmVpPMCurrentVpi	Integer32
	atmVpPMCurrentTxClp01	Gauge32
	atmVpPMCurrentTxClp0	Gauge32
	atmVpPMCurrentRxClp01	Gauge32
	atmVpPMCurrentRxClp0	Gauge32
	atmVpPMCurrentErroredCells	Gauge32
	atmVpPMCurrentLostCells	Gauge32
	atmVpPMCurrentMisinsertedCells	Gauge32
	atmVpPMCurrentECB	Gauge32
	atmVpPMCurrentSECB	Gauge32
	atmVpPMCurrentES	Gauge32
	atmVpPMCurrentSES	Gauge32
	atmVpPMCurrentUAS	Gauge32
	atmVpPMCurrentIntervalQuality	INTEGER
	atmVpPMCurrentLastDayQuality	INTEGER

AtmVpIntervalEntry
SEQUENCE
	atmVpIntervalVpi	Integer32
	atmVpIntervalNumber	Integer32
	atmVpIntervalRxCellsClp01	Gauge32
	atmVpIntervalRxCellsClp0	Gauge32
	atmVpIntervalGcra0Violations	Gauge32
	atmVpIntervalGcra1Violations	Gauge32
	atmVpIntervalRxAIS	Gauge32
	atmVpIntervalTxAIS	Gauge32
	atmVpIntervalRxRDI	Gauge32
	atmVpIntervalTxRDI	Gauge32
	atmVpIntervalContinuityLoss	Gauge32
	atmVpIntervalUAS	Gauge32
	atmVpIntervalSES	Gauge32
	atmVpIntervalCDC	Gauge32
	atmVpIntervalTotalDiscards	Gauge32
	atmVpIntervalClp0Discards	Gauge32
	atmVpIntervalTotalCellOuts	Gauge32
	atmVpIntervalClp0CellOuts	Gauge32
	atmVpIntervalTaggedOuts	Gauge32
	atmVpIntervalPCR	Gauge32
	atmVpIntervalSCR	Gauge32
	atmVpIntervalMCR	Gauge32
	atmVpIntervalShaperTotalDiscards	Gauge32
	atmVpIntervalShaperClp0Discards	Gauge32
	atmVpIntervalShaperClp1Discards	Gauge32

AtmVpPMIntervalEntry
SEQUENCE
	atmVpPMIntervalVpi	Integer32
	atmVpPMIntervalDir	INTEGER
	atmVpPMIntervalNumber	Integer32
	atmVpPMIntervalTxClp01	Gauge32
	atmVpPMIntervalTxClp0	Gauge32
	atmVpPMIntervalRxClp01	Gauge32
	atmVpPMIntervalRxClp0	Gauge32
	atmVpPMIntervalErroredCells	Gauge32
	atmVpPMIntervalLostCells	Gauge32
	atmVpPMIntervalMisinsertedCells	Gauge32
	atmVpPMIntervalECB	Gauge32
	atmVpPMIntervalSECB	Gauge32
	atmVpPMIntervalES	Gauge32
	atmVpPMIntervalSES	Gauge32
	atmVpPMIntervalUAS	Gauge32
	atmVpPMIntervalQuality	INTEGER
	atmVpPMIntervalLastDayQuality	INTEGER

AtmVpQoSEntry
SEQUENCE
	atmVpQoSPeriodRef	INTEGER
	atmVpQoSElapsedTime	Integer32
	atmVpQoSUAS	Gauge32

AtmVpPMQoSEntry
SEQUENCE
	atmVpPMQoSDirection	INTEGER
	atmVpPMQoSPeriodRef	INTEGER
	atmVpPMQoSCLR	Gauge32
	atmVpPMQoSCER	Gauge32
	atmVpPMQoSCMR	Gauge32

AtmVpShaperStatEntry
SEQUENCE
	atmVpShaperDiscarded	Counter32
	atmVpShaperOccupation	Integer32
	atmVpShaperMaxOccupation	Integer32
	atmVpShaperLevel	INTEGER
	atmVpShaperEpdDropped	Counter32
	atmVpShaperTotalEpdDropped	Counter32

AtmVcCurrentEntry
SEQUENCE
	atmVcCurrentVpi	Integer32
	atmVcCurrentVci	Integer32
	atmVcCurrentRxCellsClp01	Gauge32
	atmVcCurrentRxCellsClp0	Gauge32
	atmVcCurrentGcra0Violations	Gauge32
	atmVcCurrentGcra1Violations	Gauge32
	atmVcCurrentRxAIS	Gauge32
	atmVcCurrentTxAIS	Gauge32
	atmVcCurrentRxRDI	Gauge32
	atmVcCurrentTxRDI	Gauge32
	atmVcCurrentContinuityLoss	Gauge32
	atmVcCurrentUAS	Gauge32
	atmVcCurrentSES	Gauge32
	atmVcCurrentCDC	Gauge32
	atmVcCurrentTotalDiscards	Gauge32
	atmVcCurrentClp0Discards	Gauge32
	atmVcCurrentTotalCellOuts	Gauge32
	atmVcCurrentClp0CellOuts	Gauge32
	atmVcCurrentTaggedOuts	Gauge32
	atmVcCurrentPCR	Gauge32
	atmVcCurrentSCR	Gauge32
	atmVcCurrentMCR	Gauge32
	atmVcCurrentShaperTotalDiscards	Gauge32
	atmVcCurrentShaperClp0Discards	Gauge32
	atmVcCurrentShaperClp1Discards	Gauge32

AtmVcPMCurrentEntry
SEQUENCE
	atmVcPMCurrentVpi	Integer32
	atmVcPMCurrentVci	Integer32
	atmVcPMCurrentDir	Integer32
	atmVcPMCurrentTxClp01	Gauge32
	atmVcPMCurrentTxClp0	Gauge32
	atmVcPMCurrentRxClp01	Gauge32
	atmVcPMCurrentRxClp0	Gauge32
	atmVcPMCurrentErroredCells	Gauge32
	atmVcPMCurrentLostCells	Gauge32
	atmVcPMCurrentMisinsertedCells	Gauge32
	atmVcPMCurrentECB	Gauge32
	atmVcPMCurrentSECB	Gauge32
	atmVcPMCurrentES	Gauge32
	atmVcPMCurrentSES	Gauge32
	atmVcPMCurrentUAS	Gauge32
	atmVcPMCurrentIntervalQuality	INTEGER
	atmVcPMCurrentLastDayQuality	INTEGER

AtmVcIntervalEntry
SEQUENCE
	atmVcIntervalVpi	Integer32
	atmVcIntervalVci	Integer32
	atmVcIntervalNumber	Integer32
	atmVcIntervalRxCellsClp01	Gauge32
	atmVcIntervalRxCellsClp0	Gauge32
	atmVcIntervalGcra0Violations	Gauge32
	atmVcIntervalGcra1Violations	Gauge32
	atmVcIntervalRxAIS	Gauge32
	atmVcIntervalTxAIS	Gauge32
	atmVcIntervalRxRDI	Gauge32
	atmVcIntervalTxRDI	Gauge32
	atmVcIntervalContinuityLoss	Gauge32
	atmVcIntervalUAS	Gauge32
	atmVcIntervalSES	Gauge32
	atmVcIntervalCDC	Gauge32
	atmVcIntervalTotalDiscards	Gauge32
	atmVcIntervalClp0Discards	Gauge32
	atmVcIntervalTotalCellOuts	Gauge32
	atmVcIntervalClp0CellOuts	Gauge32
	atmVcIntervalTaggedOuts	Gauge32
	atmVcIntervalPCR	Gauge32
	atmVcIntervalSCR	Gauge32
	atmVcIntervalMCR	Gauge32
	atmVcIntervalShaperTotalDiscards	Gauge32
	atmVcIntervalShaperClp0Discards	Gauge32
	atmVcIntervalShaperClp1Discards	Gauge32

AtmVcPMIntervalEntry
SEQUENCE
	atmVcPMIntervalVpi	Integer32
	atmVcPMIntervalVci	Integer32
	atmVcPMIntervalDir	INTEGER
	atmVcPMIntervalNumber	Integer32
	atmVcPMIntervalTxClp01	Gauge32
	atmVcPMIntervalTxClp0	Gauge32
	atmVcPMIntervalRxClp01	Gauge32
	atmVcPMIntervalRxClp0	Gauge32
	atmVcPMIntervalErroredCells	Gauge32
	atmVcPMIntervalLostCells	Gauge32
	atmVcPMIntervalMisinsertedCells	Gauge32
	atmVcPMIntervalECB	Gauge32
	atmVcPMIntervalSECB	Gauge32
	atmVcPMIntervalES	Gauge32
	atmVcPMIntervalSES	Gauge32
	atmVcPMIntervalUAS	Gauge32
	atmVcPMIntervalQuality	INTEGER
	atmVcPMIntervalLastDayQuality	INTEGER

AtmVcQoSEntry
SEQUENCE
	atmVcQoSPeriodRef	INTEGER
	atmVcQoSElapsedTime	Integer32
	atmVcQoSUAS	Gauge32

AtmVcPMQoSEntry
SEQUENCE
	atmVcPMQoSDirection	INTEGER
	atmVcPMQoSPeriodRef	INTEGER
	atmVcPMQoSCLR	Gauge32
	atmVcPMQoSCER	Gauge32
	atmVcPMQoSCMR	Gauge32

AtmVcShaperStatEntry
SEQUENCE
	atmVcShaperDiscarded	Counter32
	atmVcShaperOccupation	Integer32
	atmVcShaperMaxOccupation	Integer32
	atmVcShaperLevel	INTEGER
	atmVcShaperEpdDropped	Counter32
	atmVcShaperTotalEpdDropped	Counter32

AtmIntervalDateEntry
SEQUENCE
	atmIntervalDateInterval	Integer32
	atmIntervalDateDate	DisplayString
	atmIntervalDateTime	DisplayString

AtmNteManagerEntry
SEQUENCE
	atmNteManagerIP	IpAddress
	atmNteManagerPvc	Integer32
	atmNteManagerIfIndex	Integer32
	atmNteManagerVpi	Integer32
	atmNteManagerVci	Integer32
	atmNteManagerTrapMask	Integer32
	atmNteManagerRowStatus	RowStatus
	atmNteManagerNextHop	IpAddress
	atmNteManagerVlanSupport	INTEGER
	atmNteManagerVlanIdentifier	Integer32
	atmNteManagerVlanFramePriority	Integer32
	atmNteManagerAlarmTrapMask	OCTET STRING
	atmNteManagerConfigPorts	Integer32

AtmNteConfOamIfEntry
SEQUENCE
	atmNteConfOamIfAisRdi	INTEGER

AtmNteHostIfEntry
SEQUENCE
	atmNteHostPvcIndex	Integer32
	atmNteHostIP	IpAddress
	atmNteHostMask	IpAddress
	atmNteHostAtmIfIndex	Integer32
	atmNteHostVpi	Integer32
	atmNteHostVci	Integer32
	atmNteHostRowStatus	RowStatus
	atmNteHostRdnVpi	Integer32
	atmNteHostRdnVci	Integer32
	atmNteHostDefaultNextHop	IpAddress
	atmNteHostVlanTagging	INTEGER
	atmNteHostDefaultVlanID	Integer32
	atmNteHostDefaultVlanPriority	Integer32

AtmNteOamEntry
SEQUENCE
	atmNteOamMode	INTEGER
	atmNteOamCellType	INTEGER
	atmNteOamLevel	INTEGER
	atmNteOamEnable	INTEGER

AtmAlarmForwardingEntry
SEQUENCE
	atmAlarmForwardingFailPort	Integer32
	atmAlarmForwardingToPort	Integer32
	atmAlarmForwardingRowStatus	RowStatus
	atmAlarmForwardingFailureLevel	BITS
	atmAlarmForwardingRecoveryMode	INTEGER
	atmAlarmForwardingRecoveryCommand	INTEGER
	atmAlarmForwardingTimeFilterWindow	Unsigned32

AtmVpCrossConnectExtenEntry
SEQUENCE
	atmVpCrossConnectName	SnmpAdminString

AtmVcCrossConnectExtenEntry
SEQUENCE
	atmVcCrossConnectName	SnmpAdminString

AtmTrafficDescrParamXEntry
SEQUENCE
	atmTrafficDescrParamMode	INTEGER

AtmNteIdEntry
SEQUENCE
	atmNteIdIndex	Integer32
	atmNteUnitId	Integer32
	atmNteUnitVersion	DisplayString
	atmNteCardType	INTEGER
	atmNteCardStatus	INTEGER
	atmNteCardCmd	INTEGER
	atmNteProgCardType	INTEGER

AtmSysIntervalEntry
SEQUENCE
	atmSysIntervalNumber	Integer32
	atmSysIntervalCdc	Gauge32

AtmLoopbackVpEntry
SEQUENCE
	atmLoopbackVpIfIndex	Integer32
	atmLoopbackVpVpi	Integer32
	atmLoopbackVpOperStatus	INTEGER
	atmLoopbackVpCDV	Integer32
	atmLoopbackVpAverageDelay	Integer32
	atmLoopbackVpMaxDelay	Integer32
	atmLoopbackVpMinDelay	Integer32
	atmLoopbackVpErrSessions	Integer32

AtmLoopbackVcEntry
SEQUENCE
	atmLoopbackVcIfIndex	Integer32
	atmLoopbackVcVpi	Integer32
	atmLoopbackVcVci	Integer32
	atmLoopbackVcOperStatus	INTEGER
	atmLoopbackVcCDV	Integer32
	atmLoopbackVcAverageDelay	Integer32
	atmLoopbackVcMaxDelay	Integer32
	atmLoopbackVcMinDelay	Integer32
	atmLoopbackVcErrSessions	Integer32

AtmLoopbackVpIvlEntry
SEQUENCE
	atmLoopbackVpIvlIfIndex	Integer32
	atmLoopbackVpIvlVpi	Integer32
	atmLoopbackVpIvlIvl	Integer32
	atmLoopbackVpIvlOperStatus	INTEGER
	atmLoopbackVpIvlCDV	Integer32
	atmLoopbackVpIvlAverageDelay	Integer32
	atmLoopbackVpIvlMaxDelay	Integer32
	atmLoopbackVpIvlMinDelay	Integer32
	atmLoopbackVpIvlErrSessions	Integer32

AtmLoopbackVcIvlEntry
SEQUENCE
	atmLoopbackVcIvlIfIndex	Integer32
	atmLoopbackVcIvlVpi	Integer32
	atmLoopbackVcIvlVci	Integer32
	atmLoopbackVcIvlIvl	Integer32
	atmLoopbackVcIvlOperStatus	INTEGER
	atmLoopbackVcIvlCDV	Integer32
	atmLoopbackVcIvlAverageDelay	Integer32
	atmLoopbackVcIvlMaxDelay	Integer32
	atmLoopbackVcIvlMinDelay	Integer32
	atmLoopbackVcIvlErrSessions	Integer32

AtmVpPmEntry
SEQUENCE
	atmVpPmIfIndex	Integer32
	atmVpPmVpi	Integer32
	atmVpPmAdminStatus	INTEGER
	atmVpPmDirection	INTEGER
	atmVpPmBlockSize	Integer32
	atmVpPmRowStatus	RowStatus
	atmVpPmSink	INTEGER
	atmVpPmSource	INTEGER

AtmVcPmEntry
SEQUENCE
	atmVcPmIfIndex	Integer32
	atmVcPmVpi	Integer32
	atmVcPmVci	Integer32
	atmVcPmAdminStatus	INTEGER
	atmVcPmDirection	INTEGER
	atmVcPmBlockSize	Integer32
	atmVcPmRowStatus	RowStatus
	atmVcPmSink	INTEGER
	atmVcPmSource	INTEGER

AtmNteMdlConfigEntry
SEQUENCE
	atmNteMdlSlotIndex	Integer32
	atmNteMdlPrtCpuSharing	INTEGER
	atmNteMdlInputPriorityMechanism	INTEGER

AtmGenSysSelfTestEntry
SEQUENCE
	atmGenSysSelfTestIndex	Integer32
	atmGenSysSelfTestResult	DisplayString
	atmGenSysSelfTestModule	DisplayString

AtmGenSysLogEntry
SEQUENCE
	atmGenSysLogIndex	Integer32
	atmGenSysLogMessage	DisplayString

AtmGenSysCxRefEntry
SEQUENCE
	atmGenSysCxRefIndex	Integer32
	atmGenSysCxRefCounter	Gauge32

Ip2IfEntry
SEQUENCE
	ip2IfChannelIndex	Integer32
	ip2IfRowStatus	RowStatus
	ip2IfOperStatus	INTEGER
	ip2IfAdminStatus	INTEGER
	ip2IfDestAddr	IpAddress
	ip2IfNextHop	IpAddress
	ip2IfDestPort	Integer32
	ip2IfMacAddr	MacAddress
	ip2IfJitterBuffer	Integer32
	ip2IfTos	Integer32
	ip2IfTDMBytesInFrame	Integer32
	ip2IfVlanSupport	INTEGER
	ip2IfVlanIdentifier	Integer32
	ip2IfVlanFramePriority	Integer32
	ip2IfExitPort	INTEGER
	ip2IfVoiceOos	OCTET STRING
	ip2IfDataOos	OCTET STRING
	ip2IfBundleUsage	Integer32
	ip2IfOAM	OCTET STRING
	ip2IfTDMoIpMode	INTEGER
	ip2IfTimeElapsed	Integer32
	ip2IfValidIntervals	Integer32
	ip2IfFarEndType	INTEGER
	ip2IfRdnState	INTEGER
	ip2IfSourceAddr	IpAddress
	ip2IfBandWidth	Integer32
	ip2IfMeasuredSilence	Integer32
	ip2IfPayloadType	INTEGER
	ip2IfProtocolVersion	INTEGER
	ip2IfTdmBackUpNextHop	IpAddress
	ip2IfOosTxEnable	INTEGER
	ip2IfConnCheckPktFrequency	Integer32
	ip2IfConnPktTimeOutCycles	Integer32
	ip2IfMfRelay	INTEGER
	ip2IfTxGain	Integer32
	ip2IfSuperTandem	INTEGER
	ip2IfSrcPort	Integer32
	ip2IfModemCalls	INTEGER
	ip2IfMinPulseWidth	Integer32
	ip2IfMinPowerLevel	Integer32
	ip2IfEchoCanceler	INTEGER
	ip2IfCodingLaw	INTEGER
	ip2IfCustomToneDetect	INTEGER
	ip2IfCallerIdDelay	Integer32
	ip2IfConnectivityMode	INTEGER
	ip2IfClockSourceEnable	INTEGER
	ip2IfNetworkType	INTEGER
	ip2IfMplsRxLabelEnable	INTEGER
	ip2IfMplsRxLabel	Integer32
	ip2IfMplsTxLabelEnable	INTEGER
	ip2IfMplsTxLabel	Integer32
	ip2IfMplsTxExpBits	Integer32
	ip2IfMfcSpoofing	INTEGER
	ip2IfToneAckInterval	Integer32
	ip2IfNextHopType	INTEGER
	ip2IfNoiseLevelForVAD	INTEGER
	ip2IfClockPreferences	INTEGER
	ip2IfConnectionMode	INTEGER
	ip2IfRingBack	INTEGER
	ip2IfReversePolarity	INTEGER
	ip2IfPulseMeter	INTEGER
	ip2IfPulseMeterFreq	INTEGER
	ip2IfPulseMeterPeriod	Integer32
	ip2IfOnHookDetect	INTEGER
	ip2IfComfortNoiseGen	INTEGER
	ip2IfExitChannel	Integer32
	ip2IfMaxVBDModemCalls	Integer32
	ip2IfMaxRelayModemCalls	Integer32
	ip2IfCustomToneFrequency	INTEGER
	ip2IfVadMethod	INTEGER
	ip2IfRxGain	Integer32
	ip2IfCallerIDType	INTEGER
	ip2IfPeerAddrType	INTEGER
	ip2IfVbdRate	INTEGER
	ip2IfDtmfDetection	INTEGER
	ip2IfNlpCutoffLevel	Unsigned32
	ip2IfDtdErlRatioCutoffQ3	Unsigned32
	ip2IfCASRedundancy	INTEGER
	ip2IfBundleSensitivity	INTEGER
	ip2IfOAMBundleIdent	INTEGER
	ip2IfMaxTxQueue	Unsigned32
	ip2IfMaxGprsTxQueue	Unsigned32
	ip2IfV23HD	INTEGER
	ip2IfModemProtocolMode	OCTET STRING
	ip2IfCdisCngDetectionTime	Unsigned32
	ip2IfSuperTandemBitMask	OCTET STRING
	ip2IfVbdSwitchbackTime	Unsigned32
	ip2IfCallerIdTxGain	Integer32
	ip2IfCallerIdRxGain	Integer32
	ip2IfUdpMuxMethod	INTEGER
	ip2IfCallerIdDetection	INTEGER
	ip2IfWap	INTEGER

Ip2IfStatEntry
SEQUENCE
	ip2IfStatChIndex	Integer32
	ip2IfStatSeqErrors	Integer32
	ip2IfStatBufUnderflows	Integer32
	ip2IfStatBufOverflows	Integer32
	ip2IfStatTxOnTimeInterval	Counter32
	ip2IfStatTxOnMaxSize	Counter32
	ip2IfStatRxSignaling	Counter32
	ip2IfStatRxVoice	Counter32
	ip2IfStatRxHdlc	Counter32
	ip2IfStatTxSignaling	Counter32
	ip2IfStatTxVoice	Counter32
	ip2IfStatTxHdlc	Counter32
	ip2IfStatRdnFlip	Counter32
	ip2IfFarEndTdmStatus	Integer32
	ip2IfStatPsnTxFrames	Counter32
	ip2IfStatPsnRxFrames	Counter32
	ip2IfStatMinJittBufLevel	Unsigned32
	ip2IfStatMaxJittBufLevel	Unsigned32
	ip2IfStatRecommendedJittBufSize	Unsigned32
	ip2IfStatPsnSeqErrors	Counter32
	ip2IfStatPsnReorderFrames	Counter32
	ip2IfStatMinRoundTripDelay	Unsigned32
	ip2IfStatMaxRoundTripDelay	Unsigned32
	ip2IfStatAvrRoundTripDelay	Unsigned32
	ip2IfStatFrameTrackDupDrop	Counter32
	ip2IfStatFrameTrackMissing	Counter32
	ip2IfStatFrameTrackLongSerMiss	Integer32
	ip2IfStatTxMeasuredSilence	Integer32
	ip2IfStatRxMeasuredSilence	Integer32
	ip2IfStatHdlcCrcErr	Counter32
	ip2IfStatHdlcAlignErr	Counter32
	ip2IfStatHdlcOversize	Counter32
	ip2IfStatHdlcUndersize	Counter32
	ip2IfStatHdlcAbort	Counter32
	ip2IfStatRxCorrectFrames	Counter32
	ip2IfStatHdlcErroredFrames	Counter32

Ip2IfPortEntry
SEQUENCE
	ip2IfPortIndex	Integer32
	ip2IfPortUsage	Integer32
	ip2IfPortMask	INTEGER
	ip2IfPortTotalThroughput	Integer32

Ip2IfCurrentStatEntry
SEQUENCE
	ip2IfCurrentStatSeqErrors	Counter32
	ip2IfCurrentStatBufUnderflows	Counter32
	ip2IfCurrentStatBufOverflows	Counter32
	ip2IfCurrentStatMaxDelayVar	Integer32
	ip2IfCurrentStatMinJittBufLevel	Unsigned32
	ip2IfCurrentStatMaxJittBufLevel	Unsigned32
	ip2IfCurrentStatTxErrFrameSec	Counter32

Ip2IfIntervalStatEntry
SEQUENCE
	ip2IfIntervalStatIndex	Integer32
	ip2IfIntervalStatSeqErrors	Counter32
	ip2IfIntervalStatBufUnderflows	Counter32
	ip2IfIntervalStatBufOverflows	Counter32
	ip2IfIntervalStatMaxDelayVar	Integer32
	ip2IfIntervalStatMinJittBufLevel	Unsigned32
	ip2IfIntervalStatMaxJittBufLevel	Unsigned32
	ip2IfIntervalStatTxErrFrameSec	Counter32

PrtBdbandIndEntry
SEQUENCE
	prtBdbandCnfgIdx	Integer32
	prtBdbandIdx	Integer32
	prtBdbandIndSig	INTEGER
	prtBdbandIndEvent	INTEGER
	prtBdbandIndSigEnable	INTEGER
	prtBdbandRowStatus	RowStatus

PrtPhyConfigEntry
SEQUENCE
	prtPhyTimeElapsed	Integer32
	prtPhyValidIntervals	Integer32

PrtPhyCurrentEntry
SEQUENCE
	prtPhyCurrentLOS	Gauge32
	prtPhyCurrentLSV	Gauge32
	prtPhyCurrentUAS	Gauge32
	prtPhyCurrentSES	Gauge32
	prtPhyCurrentES	Gauge32
	prtPhyCurrentStatus	OCTET STRING
	prtPhyCurrentLOF	Gauge32

PrtPhyIntervalEntry
SEQUENCE
	prtPhyIntervalNumber	Integer32
	prtPhyIntervalLOS	Gauge32
	prtPhyIntervalLSV	Gauge32
	prtPhyIntervalUAS	Gauge32
	prtPhyIntervalSES	Gauge32
	prtPhyIntervalES	Gauge32
	prtPhyIntervalStatus	OCTET STRING
	prtPhyIntervalLOF	Gauge32

WrDhcpEntry
SEQUENCE
	wrDhcpLowIpAddress	IpAddress
	wrDhcpHighIpAddress	IpAddress
	wrDhcpIpMaskAddress	IpAddress
	wrDhcpDefaultGateway	IpAddress
	wrDhcpPrimaryDNS	IpAddress
	wrDhcpSecondaryDNS	IpAddress
	wrDhcpInterface	INTEGER
	wrDhcpRowStatus	RowStatus
	wrDhcpIpAddressLeaseTime	Integer32
	wrDhcpPoolName	SnmpAdminString
	wrDhcpTftpServerIp	IpAddress
	wrDhcpConfigFileName	SnmpAdminString

DhcpPoolAllocEntry
SEQUENCE
	dhcpPoolAllocLowIpAddress	IpAddress
	dhcpPoolAllocLeasingIpAddress	IpAddress
	dhcpPoolAllocMacAddress	MacAddress
	dhcpPoolAllocTimeLeft	Integer32
	dhcpPoolAllocFlags	INTEGER
	dhcpPoolAllocFreeCmd	INTEGER

DhcpRelayEntry
SEQUENCE
	dhcpRelayAction	INTEGER
	dhcpRelayServerIpAddress	IpAddress
	dhcpRelayMaxHop	Integer32

DhcpClientEntry
SEQUENCE
	dhcpClientAction	INTEGER
	dhcpClientServerIpAddress	IpAddress
	dhcpClientLeaseExpirationTime	Integer32
	dhcpClientStatus	DisplayString

DhcpIfClientEntry
SEQUENCE
	dhcpIfClientIpAddress	IpAddress
	dhcpIfClientRowStatus	RowStatus

WrLanIpxNetEntry
SEQUENCE
	wrLanifIndex	Integer32
	wrLanIpxFrameType	INTEGER
	wrIpxNetAddress	IpAddress

RipSapIfConfEntry
SEQUENCE
	ripSapIfConfIfIndex	Integer32
	ripSapIfConfMode	INTEGER
	ripSapIfConfStatus	RowStatus

WrIpAddressEntry
SEQUENCE
	wrIpIfIndex	Integer32
	wrIpAddress	IpAddress
	wrIpMask	IpAddress
	wrIpRowStatus	RowStatus

WrSpoofingEntry
SEQUENCE
	wrSpoofingIfIndex	Integer32
	wrSpoofingAction	Integer32
	wrSpoofingAgingStation	Integer32
	wrSpoofingRowStatus	RowStatus

WrLanIfEntry
SEQUENCE
	wrLanIfIndex	Integer32
	wrLanBridgeRouterMode	INTEGER
	wrLanIfState	INTEGER
	wrLanIfRdnTimeout	Integer32

WrSyncCnfgEntry
SEQUENCE
	wrSyncIfIndex	Integer32
	wrSyncClkMode	INTEGER
	wrSyncClkRate	INTEGER

WrFrCnfgEntry
SEQUENCE
	wrFrDlciLearningMode	INTEGER
	wrFrCllmMessages	INTEGER

SysDclEntry
SEQUENCE
	sysDclCnfgIdx	Integer32
	sysDclRedundancy	INTEGER
	sysDclActiveCl	INTEGER
	sysDclFlipDelay	Integer32
	sysDclFlipUponStnClk	INTEGER
	sysDclChFailThreshold	Integer32
	sysDclChPriority	OCTET STRING
	sysDclConfigDownloadSrc	INTEGER
	sysDclSwDownloadSrc	INTEGER
	sysDclRedundancyStatus	BITS

SysDclCopyDbEntry
SEQUENCE
	sysDclCopyDbIdx	Integer32
	sysDclCopyDbCmd	INTEGER

SysSErrListEntry
SEQUENCE
	sysSErrType	INTEGER
	sysSErrIdx	Integer32
	sysSErrDescription	DisplayString

SysSRdnFlipEntry
SEQUENCE
	sysSRdnFlipIdx	Integer32
	sysSRdnFlipSlot	INTEGER
	sysSRdnFlipPort	Integer32
	sysSRdnFlipCause	DisplayString
	sysSRdnFlipDate	DisplayString
	sysSRdnFlipTime	DisplayString

SysSBusEntry
SEQUENCE
	sysSBusPortIdx	Integer32
	sysSBusStatus	INTEGER
	sysSBusCapturePort	Integer32
	sysSBusUtilization	Integer32

SysSAlrEntry
SEQUENCE
	sysSAlrIdx	Integer32
	sysSAlrCode	Integer32
	sysSAlrState	INTEGER
	sysSAlarmMask	INTEGER
	sysSAlarmInvert	INTEGER
	sysSAlarmOnOff	INTEGER
	sysSAlarmCounter	Integer32

SysBufferAlrEntry
SEQUENCE
	sysBufferAlrIdx	Integer32
	sysBufferAlrCode	Integer32
	sysBufferAlrState	INTEGER
	sysBufferAlrSlot	INTEGER
	sysBufferAlrPort	Integer32
	sysBufferAlrDate	DisplayString
	sysBufferAlrTime	DisplayString
	sysBufferAlrUpTime	TimeTicks
	sysBufferAlrInfo	SnmpAdminString

SysCClkSrcEntry
SEQUENCE
	sysCClkCnfgIdx	Integer32
	sysCClkSrcIdx	INTEGER
	sysCClkSrcMode	INTEGER
	sysCClkSrcPrt	Integer32
	sysCClkStationFreq	INTEGER
	sysCClkRevertiveTimeout	Integer32
	sysCClkStationIf	INTEGER
	sysCClkStationCableMode	INTEGER
	sysCClkStationOutState	INTEGER
	sysCClkSsmBased	INTEGER
	sysCClkSSubsystemSlot	INTEGER
	sysCClkRecoveredID	Unsigned32

SysCnfgEntry
SEQUENCE
	sysCnfgIdx	Integer32
	sysCMatrixMode	INTEGER
	sysCIsdnFormat	INTEGER
	sysCRoutingOnEth	INTEGER
	sysCAutoConfigEnable	INTEGER
	sysCIntTsAllocMode	INTEGER
	sysCBuPrimaryPort	INTEGER
	sysCEnableLanOverTdm	INTEGER
	sysCSs7FisuSuppression	Integer32
	sysCBuRecMode	INTEGER

SysCRdnEntry
SEQUENCE
	sysCRdnCnfgIdx	Integer32
	sysCRdnPrimeSlot	INTEGER
	sysCRdnPrimePort	Integer32
	sysCRdnSecSlot	INTEGER
	sysCRdnSecPort	Integer32
	sysCRdnMode	INTEGER
	sysCRdnRecMode	INTEGER
	sysCRdnRecTime	Integer32
	sysCRdnHwSwFlip	INTEGER
	sysCRdnRowStatus	RowStatus
	sysCRdnOnline	INTEGER
	sysCRdnSwitchingMode	INTEGER
	sysCRdnFlipUponEvent	Integer32
	sysCRdnLosOrLofTime	Integer32
	sysCRdnEventsTimeWindow	Integer32
	sysCRdnSequenceNumberThreshold	Integer32
	sysCRdnBufferErrorsThreshold	Integer32
	sysCRdnBuffUnderrunTime	Integer32
	sysCRdnPrimePriority	INTEGER
	sysCRdnSecPriority	INTEGER
	sysCRdnWTR	Unsigned32
	sysCRdnName	SnmpAdminString
	sysCRdnTxDownDurationUponFlip	Unsigned32

SysSRdnCmdEntry
SEQUENCE
	sysSRdnEnforcedChannel	INTEGER
	sysSRdnLockFlip	INTEGER
	sysSRdnManualFlip	INTEGER

SysDbaseFlipEntry
SEQUENCE
	sysDbaseFlipIdx	Integer32
	sysDbaseFlipTime	DisplayString
	sysDbaseFlipActivation	INTEGER

MdlSEntry
SEQUENCE
	mdlSSltIdx	INTEGER
	mdlSCardType	INTEGER
	mdlSHwVer	DisplayString
	mdlSSwVer	DisplayString
	mdlSAlarmStatus	INTEGER
	mdlSAlarmStatusAll	INTEGER
	mdlSTestStatus	INTEGER
	mdlSHwStatus	INTEGER
	mdlSActivity	INTEGER
	mdlSAlrClearCmd	INTEGER
	mdlSAlrClearAllCmd	INTEGER
	mdlSAlrMaskAll	INTEGER
	mdlSCmd	Integer32
	mdlSReset	INTEGER
	mdlSRebuildFrame	INTEGER
	mdlSBackupSwVer	DisplayString
	mdlSSecondaryBackupSwVer	DisplayString
	mdlSPiggybackVer	SnmpAdminString

MdlCEntry
SEQUENCE
	mdlCConfigIdx	Integer32
	mdlCSlotIdx	INTEGER
	mdlCProgCardType	INTEGER
	mdlCNoOfExtPrt	Integer32
	mdlCNoOfIntPrt	Integer32
	mdlCParam	Integer32

MdlAlrEntry
SEQUENCE
	mdlAlrSltIdx	INTEGER
	mdlAlrIdx	Integer32
	mdlAlrCode	Integer32
	mdlAlrState	INTEGER
	mdlAlarmMask	INTEGER
	mdlAlarmInvert	INTEGER
	mdlAlarmOnOff	INTEGER
	mdlAlarmCounter	Integer32

MdlAlrMaskEntry
SEQUENCE
	mdlAlrMaskSltIdx	INTEGER
	mdlAlrMask	OCTET STRING

MdlClEntry
SEQUENCE
	mdlClIdx	INTEGER
	mdlClSwchStatus	Integer32
	mdlClLastFlipDate	DisplayString
	mdlClLastFlipTime	DisplayString
	mdlClLastFlipCause	DisplayString

MdlPsEntry
SEQUENCE
	mdlPsIdx	INTEGER
	mdlPsStatus	INTEGER
	mdlPsTestResult	INTEGER

PrtGenEntry
SEQUENCE
	prtGenPrtIdx	Integer32
	prtGenSlt	INTEGER
	prtGenExtInt	INTEGER
	prtGenIfIndex	Integer32
	prtGenActiveStatus	INTEGER
	prtGenAlrStatus	INTEGER
	prtGenTestStatus	INTEGER
	prtGenTestMask	Integer32
	prtGenTestCmd	Integer32
	prtGenTestRunning	Integer32
	prtGenType	INTEGER
	prtGenInterfaceType	DisplayString
	prtGenAlrClearCmd	INTEGER
	prtGenAlrMaskAll	INTEGER
	prtGenParamStatus	OCTET STRING
	prtGenRdnStatus	INTEGER
	prtGenTestMaskXP	OCTET STRING
	prtGenTestCmdXP	OCTET STRING
	prtGenTestRunningXP	OCTET STRING

PrtGenTestDurationEntry
SEQUENCE
	prtGenTestPrtIdx	Integer32
	prtGenTestIdx	INTEGER
	prtGenTestDuration	Integer32

PrtGenTsEntry
SEQUENCE
	prtGenTsCnfgIdx	Integer32
	prtGenTsPrtIdx	Integer32
	prtGenTsIdx	Integer32
	prtGenTsType	INTEGER
	prtGenTsIConPrt	Integer32
	prtGenTsIConTs	Integer32

PrtSAlarmEntry
SEQUENCE
	prtSAlarmPrtIdx	Integer32
	prtSAlarmIdx	Integer32
	prtSAlarmCode	Integer32
	prtSAlarmState	INTEGER
	prtSAlarmMask	INTEGER
	prtSAlarmInvert	INTEGER
	prtSAlarmOnOff	INTEGER
	prtSAlarmCounter	Integer32

PrtAlrMaskEntry
SEQUENCE
	prtAlrMaskPrtIdx	Integer32
	prtAlrMask	OCTET STRING

PrtBertEntry
SEQUENCE
	prtBertPrtIdx	Integer32
	prtBertPattern	INTEGER
	prtBertInjectRate	INTEGER
	prtBertInjectErrRateCmd	INTEGER
	prtBertInjectSingleErrCmd	INTEGER
	prtBertRunTime	Integer32
	prtBertESs	Integer32
	prtBertSyncLoss	Integer32
	prtBertErrorBits	Integer32
	prtBertClearCounters	INTEGER
	prtBertSyncStatus	INTEGER
	prtBertTs	OCTET STRING
	prtBertResult	DisplayString
	prtBertTxBits	Integer32
	prtBertRxBits	Integer32
	prtBertTxErrorBits	Integer32

PrtMonEntry
SEQUENCE
	prtMonCnfgIdx	Integer32
	prtMonitoringIdx	Integer32
	prtMonitoringEnable	INTEGER
	prtMonitoringTSs	OCTET STRING
	prtMonitoredPort	Integer32
	prtMonitoredTSs	OCTET STRING

PrtCfgParamEntry
SEQUENCE
	prtCfgParamCnfgIdx	Integer32
	prtCfgParamIdx	Integer32
	prtCfgParamSlt	INTEGER
	prtCfgParamOperatedMl	INTEGER
	prtCfgParamMlAtoMlBPrio	INTEGER
	prtCfgParamMlBtoMlAPrio	INTEGER
	prtCfgParamInbandLoopDetection	INTEGER
	prtCfgParamInbandLoopPatternCfg	INTEGER
	prtCfgParamInbandLoopActPattern	DisplayString
	prtCfgParamInbandLoopDeactPattern	DisplayString

PrtT1E1StatEntry
SEQUENCE
	prtT1E1SPrtIdx	Integer32
	prtT1E1SSlt	INTEGER
	prtT1E1OosCount	Gauge32
	prtT1E1BpvLastMin	Gauge32
	prtT1E1BpvMax	Gauge32

PrtT1E1CnfgEntry
SEQUENCE
	prtT1E1CnfgIdx	Integer32
	prtT1E1PrtIdx	Integer32
	prtT1E1Slt	INTEGER
	prtT1E1LineType	INTEGER
	prtT1E1LineCode	INTEGER
	prtT1E1SignalMode	INTEGER
	prtT1E1Fdl	INTEGER
	prtT1E1FdlMode	INTEGER
	prtT1E1Sync	INTEGER
	prtT1E1CGA	INTEGER
	prtT1E1IdleCode	OCTET STRING
	prtT1E1OosSignal	INTEGER
	prtT1E1VoiceOos	OCTET STRING
	prtT1E1DataOos	OCTET STRING
	prtT1E1LineLengthMask	INTEGER
	prtT1E1TxGainMask	INTEGER
	prtT1E1InbandMng	INTEGER
	prtT1E1InbandMngRate	INTEGER
	prtT1E1DedicatedTs	Integer32
	prtT1E1InbandMngRoutProt	INTEGER
	prtT1E1LinkMode	INTEGER
	prtT1E1Multiplier	INTEGER
	prtT1E1RxGain	INTEGER
	prtT1E1RAI	INTEGER
	prtT1E1LineMode	INTEGER
	prtT1E1TS0SaBits	OCTET STRING
	prtT1E1ConnectedTS	INTEGER
	prtT1E1Ts0SaBit	INTEGER
	prtT1E1SameFeCnfg	INTEGER
	prtT1E1RemCrc4	INTEGER
	prtT1E1MaxTSs	Integer32
	prtT1E1EocTsConfig	INTEGER
	prtT1E1Role	INTEGER
	prtT1E1PppEchoFailDetection	INTEGER

PrtT1E1FdlMsgEntry
SEQUENCE
	prtT1E1FdlMsgPrtIdx	Integer32
	prtT1E1FdlMsgFdlType	INTEGER
	prtT1E1FdlMsgSlt	INTEGER
	prtT1E1FdlMsg	OCTET STRING

PrtHSParamEntry
SEQUENCE
	prtHSCnfgIdx	Integer32
	prtHSPrtIdx	Integer32
	prtHSSlt	INTEGER
	prtHSRate	INTEGER
	prtHSFifoSize	INTEGER
	prtHSClkMode	INTEGER
	prtHSCTS	INTEGER
	prtHSRtsState	INTEGER
	prtHSInbandLoopback	INTEGER
	prtHSInbandLoopPatternCfg	INTEGER
	prtHSInbandLoopActPattern	DisplayString
	prtHSInbandLoopDeactPattern	DisplayString
	prtHSDCD	INTEGER
	prtHSClkPolarity	INTEGER
	prtHSInterfaceType	INTEGER
	prtHSUnframed	INTEGER

PrtHSBertEntry
SEQUENCE
	prtHSBertPrtIdx	Integer32
	prtHSBertSlt	INTEGER
	prtHSBertCountClr	INTEGER
	prtHSBertTestResult	Integer32

PrtSpCnfgEntry
SEQUENCE
	prtSpCnfgIdx	Integer32
	prtSpPrtIdx	Integer32
	prtSpUsage	INTEGER
	prtSpRate	INTEGER
	prtSpDataBits	INTEGER
	prtSpParity	INTEGER
	prtSpCallOutMode	INTEGER
	prtSpInterface	INTEGER
	prtSpCTS	INTEGER
	prtSpDcdDelay	INTEGER
	prtSpDsr	INTEGER
	prtSpNoOfRetries	Integer32
	prtSpWaitForConnect	INTEGER
	prtSpDialMode	INTEGER
	prtSpAltNumMode	INTEGER
	prtSpPrimaryNum	DisplayString
	prtSpAltNum	DisplayString
	prtSpRoutProtocol	INTEGER
	prtSpCmd	OCTET STRING
	prtSpActCallOut	INTEGER
	prtSpAlrRelayMode	INTEGER
	prtSpStopBits	INTEGER

PrtDimCnfgEntry
SEQUENCE
	prtDimCnfgIdx	Integer32
	prtDimIdx	Integer32
	prtDimTxMode	INTEGER
	prtDimPolarity	INTEGER
	prtDimClkMode	INTEGER
	prtDimMaxDelay	INTEGER
	prtDimMng	INTEGER
	prtDimMngRoutProt	INTEGER

PrtDimDestEntry
SEQUENCE
	prtDestCnfgIdx	Integer32
	prtDestDimIdx	Integer32
	prtDestIdx	Integer32
	prtDest	Integer32
	prtDestConnect	INTEGER

PrtICnfgEntry
SEQUENCE
	prtICnfgIdx	Integer32
	prtIIdx	Integer32
	prtIRate	INTEGER
	prtIConnect	INTEGER

PrtHdslEntry
SEQUENCE
	prtHdslIdx	Integer32
	prtHdslMode	INTEGER
	prtHdslRptrType	INTEGER
	prtHdslMaxRate	INTEGER
	prtHdslLinkType	INTEGER
	prtHdslCompSwVer	DisplayString
	prtHdslCompHwVer	DisplayString

PrtT3E3CnfgEntry
SEQUENCE
	prtT3E3CnfgIdx	Integer32
	prtT3E3PrtIdx	Integer32
	prtT3E3Slt	INTEGER
	prtT3E3LineLength	INTEGER
	prtT3E3InbandMng	INTEGER
	prtT3E3AisFrame	INTEGER
	prtT3E3TxClockSource	INTEGER
	prtT3E3RoutProt	INTEGER
	prtT3E3AisTransmit	INTEGER

CmprEntry
SEQUENCE
	cmprTypeIdx	Integer32
	cmprCnfgIdx	Integer32
	cmprVersion	Integer32
	cmprSltIdx	INTEGER
	cmprPrtIdx	Integer32
	cmprObj	OCTET STRING

MapLinkEntry
SEQUENCE
	mapLinkIdx	Integer32
	mapLinkSlotIdx	INTEGER
	mapLinkPortIdx	Integer32
	mapLinkState	INTEGER

AlrGenEntry
SEQUENCE
	alrGenCode	Integer32
	alrGenDescription	DisplayString
	alrGenLevel	INTEGER
	alrGenSlotType	INTEGER
	alrGenSeverity	INTEGER
	alrGenDebounce	Integer32
	alrGenDefSeverity	INTEGER

WfqEntry
SEQUENCE
	wfqCnfgIdx	Integer32
	wfqPrtIdx	Integer32
	wfqTblIdx	Integer32
	wfqQueueIdx	Integer32
	wfqRowStatus	RowStatus
	wfqWeightValue	Integer32
	wfqSchedulingMode	INTEGER
	wfqMinRateAbsolute	Unsigned32
	wfqMaxPacketSize	Unsigned32

Dscp
A Differentiated Services Code-Point that may be used for marking a traffic stream.
TEXTUAL-CONVENTION
	Integer32	0..63

DscpMappingEntry
SEQUENCE
	dscpMappingCnfgIdx	Integer32
	dscpMappingDscpIdx	Dscp
	dscpMappingRegenPriority	Integer32

IfTeQosEntry
SEQUENCE
	ifTeQosIdx1	Integer32
	ifTeQosIdx2	Integer32
	ifTeQosIdx3	Integer32
	ifTeQosParam	OCTET STRING
	ifTeQosParam2	OCTET STRING
	ifTeQosStatus	INTEGER

PrtPriorityEntry
SEQUENCE
	prtPriorityIdx1	Integer32
	prtPriorityPrtIdx	Integer32
	prtPriorityIdx	Integer32
	prtPriorityIngressRateLimit	Integer32

PrtQosEntry
SEQUENCE
	prtQosIdx	Unsigned32
	prtQosPrtIdx	Unsigned32
	prtQosDirection	INTEGER
	prtQosRateLimitPacketType	INTEGER
	prtQosRateLimitCIR	Unsigned32
	prtQosRateLimitCBS	Unsigned32
	prtQosRateLimitEIR	Unsigned32
	prtQosRateLimitEBS	Unsigned32

PortTrafficClassEntry
SEQUENCE
	portTrafficClassIdx1	Integer32
	portTrafficClassPortIdx	Integer32
	portTrafficClass	Integer32

ServiceEntry
SEQUENCE
	flowIndex	Unsigned32
	serviceIndex	Unsigned32
	serviceRowStatus	RowStatus
	serviceName	SnmpAdminString
	serviceBwProfileId	Unsigned32

EvcCosEntry
SEQUENCE
	evcCosCnfgIdx	Unsigned32
	evcCosEvcIdx	Unsigned32
	evcCosRowStatus	RowStatus
	evcCosEvcName	SnmpAdminString
	evcCosSpVlanId	Unsigned32

ServiceStatEntry
SEQUENCE
	serviceStatDirection	INTEGER
	srvForwardGreenPackets	Gauge32
	srvForwardGreenPacktesOverflow	Gauge32
	srvForwardYellowPackets	Gauge32
	srvForwardYellowPacketsOverflow	Gauge32
	srvDiscardGreenPacket	Gauge32
	srvDiscardGreenPacketOverflow	Gauge32
	srvDiscardYellowRedPackets	Gauge32
	srvDiscardYellowRedPacketsOverflow	Gauge32
	srvForwardGreenBytes	Gauge32
	srvForwardGreenBytesOverflow	Gauge32
	srvForwardYellowBytes	Gauge32
	srvForwardYellowBytesOverflow	Gauge32
	srvDiscardGreenBytes	Gauge32
	srvDiscardGreenBytesOverflow	Gauge32
	srvDiscardYellowRedBytes	Gauge32
	srvDiscardYellowRedBytesOverflow	Gauge32
	srvResetStatsCmd	INTEGER
	srvDiscardYellowPackets	Gauge32
	srvDiscardYellowPacketsOverflow	Gauge32
	srvDiscardYellowBytes	Gauge32
	srvDiscardYellowBytesOverflow	Gauge32
	srvDiscardRedPackets	Gauge32
	srvDiscardRedPacketsOverflow	Gauge32
	srvDiscardRedBytes	Gauge32
	srvDiscardRedBytesOverflow	Gauge32

FlowMappingProfileEntry
SEQUENCE
	flowMappingProfileIndex	Unsigned32
	flowMappingProfilePriority	INTEGER
	flowMappingProfileRowStatus	RowStatus
	flowMappingProfileNumOfMaps	Unsigned32
	flowMappingProfileMapIndex	Unsigned32
	flowMappingProfileName	SnmpAdminString

QosFlowMappingEntry
SEQUENCE
	qosFlowMappingIdx1	Unsigned32
	qosFlowMappingIdx2	Unsigned32
	qosFlowMappingIdx3	Unsigned32
	qosFlowMappingRowStatus	RowStatus
	qosFlowMappingCriteria	BITS
	qosFlowMappingIeee802dot1p	Unsigned32
	qosFlowMappingTos	Unsigned32
	qosFlowMappingFromDscp	Unsigned32
	qosFlowMappingToDscp	Unsigned32
	qosFlowMappingFromVlanId	Unsigned32
	qosFlowMappingToVlanId	Unsigned32
	qosFlowMappingFromSrcMacAddr	MacAddress
	qosFlowMappingToSrcMacAddr	MacAddress
	qosFlowMappingFromDestMacAddr	MacAddress
	qosFlowMappingToDestMacAddr	MacAddress
	qosFlowMappingFromSrcIpAddr	IpAddress
	qosFlowMappingToSrcIpAddr	IpAddress
	qosFlowMappingFromDestIpAddr	IpAddress
	qosFlowMappingToDestIpAddr	IpAddress
	qosFlowMappingFromTcpSrcPort	Unsigned32
	qosFlowMappingToTcpSrcPort	Unsigned32
	qosFlowMappingFromTcpDestPort	Unsigned32
	qosFlowMappingToTcpDestPort	Unsigned32
	qosFlowMappingFromUdpSrcPort	Unsigned32
	qosFlowMappingToUdpSrcPort	Unsigned32
	qosFlowMappingFromUdpDestPort	Unsigned32
	qosFlowMappingToUdpDestPort	Unsigned32
	qosFlowMappingFromIpPrecedence	Unsigned32
	qosFlowMappingToIpPrecedence	Unsigned32
	qosFlowMappingInnerIeee802dot1p	Unsigned32
	qosFlowMappingFromInnerVlanId	Unsigned32
	qosFlowMappingToInnerVlanId	Unsigned32

CosProfileEntry
SEQUENCE
	cosProfileIndex	Unsigned32
	cosProfileRowStatus	RowStatus
	cosProfileCosMethod	INTEGER
	cosProfileName	SnmpAdminString
	cosProfileCosMapping	OCTET STRING

QProfileEntry
SEQUENCE
	qProfileIndex	Unsigned32
	qProfileRowStatus	RowStatus
	qProfileName	SnmpAdminString
	qProfileNumberOfInternalQ	Unsigned32
	qProfileInternalQProfile	OCTET STRING

QInternalProfileEntry
SEQUENCE
	qInternalProfileIndex	Unsigned32
	qInternalProfileRowStatus	RowStatus
	qInternalProfileScheduling	INTEGER
	qInternalProfileWFQWeight	Unsigned32
	qInternalProfileQueueLength	Unsigned32
	qInternalProfileWredStartDropThresh	Unsigned32
	qInternalProfileWredDropAllThresh	Unsigned32
	qInternalProfileWredDropProbability	Unsigned32
	qInternalProfileRateLimit	Unsigned32
	qInternalProfileShaperProfile	Unsigned32

QueueGroupEntry
SEQUENCE
	queueGroupName	SnmpAdminString
	queueGroupQBlockLevel	Unsigned32
	queueGroupQBlockIdx	Unsigned32
	queueGroupRowStatus	RowStatus
	queueGroupQBlockProfile	Unsigned32
	queueGroupQBlockShaperProfile	Unsigned32
	queueGroupPointToQBlock	SnmpAdminString
	queueGroupPointToInternalQueue	Unsigned32
	queueGroupQBlockName	SnmpAdminString

MarkingProfileEntry
SEQUENCE
	markingProfileIndex	Unsigned32
	markingProfileRowStatus	RowStatus
	markingProfileName	SnmpAdminString
	markingSpVlanPBit	OCTET STRING
	markingProfileMethod	INTEGER

EthIfEntry
SEQUENCE
	ethIfIdx	Integer32
	ethMode	INTEGER
	ethBridgingMode	INTEGER
	ethEncapsulationCRCMode	INTEGER
	ethBackPressure	INTEGER
	ethLimit4	INTEGER
	ethSkipInitReset	INTEGER
	ethMulticastBlock	INTEGER
	ethBroadcastBlock	INTEGER
	ethSpeed	INTEGER
	ethRip2	INTEGER
	ethPortPriority	INTEGER
	ethPortMngEnable	INTEGER
	ethFlowCtrlMacAddress	MacAddress
	ethRateLimit	Integer32
	ethJumboFrameEnable	INTEGER
	ethAutoMdiXEnable	INTEGER
	ethPortDataEnable	INTEGER
	ethIfUse	Integer32
	ethLineOam	INTEGER
	ethRoutingProtocol	INTEGER
	ethMdiXManualSwitch	INTEGER
	ethDot1xEnable	INTEGER
	ethPartnerRateMode	INTEGER
	ethDot1xPortRole	INTEGER

EthIfCurrentEntry
SEQUENCE
	ethIfCurrentIndex	Integer32
	ethIfCurrentStatus	OCTET STRING
	ethIfCurrentInFrames	Gauge32
	ethIfCurrentInOctets	Gauge32
	ethIfCurrentAlignmentErrors	Gauge32
	ethIfCurrentFCSErrors	Gauge32
	ethIfCurrentLengthError	Gauge32
	ethIfCurrentOutFrames	Gauge32
	ethIfCurrentOutOctets	Gauge32
	ethIfCurrentSingleCollisionFrames	Gauge32
	ethIfCurrentMultipleCollisionFrames	Gauge32
	ethIfCurrentDeferredTransmissions	Gauge32
	ethIfCurrentLateCollisions	Gauge32
	ethIfCurrentCarrierSenseErrors	Gauge32
	ethIfCurrentInputCongestionDropped	Gauge32
	ethIfCurrentOutputCongestionDropped	Gauge32
	ethIfCurrentOverflowInFrames	Gauge32
	ethIfCurrentOverflowInOctets	Gauge32
	ethIfCurrentOverflowFCSErrors	Gauge32
	ethIfCurrentOverflowOutFrames	Gauge32
	ethIfCurrentOverflowOutOctets	Gauge32
	ethIfCurrentOverflowMultipleCollisionFrames	Gauge32
	ethIfCurrentInUnicastFrames	Gauge32
	ethIfCurrentOutUnicastFrames	Gauge32
	ethIfCurrentInMulticastFrames	Gauge32
	ethIfCurrentOutMulticastFrames	Gauge32
	ethIfCurrentInBroadcastFrames	Gauge32
	ethIfCurrentOutBroadcastFrames	Gauge32
	ethIfCurrentInDiscardFrames	Gauge32
	ethIfCurrentOutDiscardFrames	Gauge32
	ethIfCurrentInPauseFrames	Gauge32
	ethIfCurrentOutPauseFrames	Gauge32
	ethIfCurrentOverflowInUnicastFrames	Gauge32
	ethIfCurrentOverflowOutUnicastFrames	Gauge32
	ethIfCurrentOverflowInMulticastFrames	Gauge32
	ethIfCurrentOverflowOutMulticastFrames	Gauge32
	ethIfCurrentOverflowInBroadcastFrames	Gauge32
	ethIfCurrentOverflowOutBroadcastFrames	Gauge32
	ethIfCurrentOverflowInDiscardFrames	Gauge32
	ethIfCurrentOverflowOutDiscardFrames	Gauge32
	ethIfCurrentOverflowInPauseFrames	Gauge32
	ethIfCurrentOverflowOutPauseFrames	Gauge32

EthIfIntervalEntry
SEQUENCE
	ethIfIntervalIndex	Integer32
	ethIfIntervalNumber	Integer32
	ethIfIntervalStatus	OCTET STRING
	ethIfIntervalInFrames	Gauge32
	ethIfIntervalInOctets	Gauge32
	ethIfIntervalAlignmentErrors	Gauge32
	ethIfIntervalFCSErrors	Gauge32
	ethIfIntervalLengthError	Gauge32
	ethIfIntervalOutFrames	Gauge32
	ethIfIntervalOutOctets	Gauge32
	ethIfIntervalSingleCollisionFrames	Gauge32
	ethIfIntervalMultipleCollisionFrames	Gauge32
	ethIfIntervalDeferredTransmissions	Gauge32
	ethIfIntervalLateCollisions	Gauge32
	ethIfIntervalCarrierSenseErrors	Gauge32
	ethIfIntervalInputCongestionDropped	Gauge32
	ethIfIntervalOutputCongestionDropped	Gauge32
	ethIfIntervalOverflowInFrames	Gauge32
	ethIfIntervalOverflowInOctets	Gauge32
	ethIfIntervalOverflowFCSErrors	Gauge32
	ethIfIntervalOverflowOutFrames	Gauge32
	ethIfIntervalOverflowOutOctets	Gauge32
	ethIfIntervalOverflowMultipleCollisionFrames	Gauge32
	ethIfIntervalInUnicastFrames	Gauge32
	ethIfIntervalOutUnicastFrames	Gauge32
	ethIfIntervalInMulticastFrames	Gauge32
	ethIfIntervalOutMulticastFrames	Gauge32
	ethIfIntervalInBroadcastFrames	Gauge32
	ethIfIntervalOutBroadcastFrames	Gauge32
	ethIfIntervalInDiscardFrames	Gauge32
	ethIfIntervalOutDiscardFrames	Gauge32
	ethIfIntervalInPauseFrames	Gauge32
	ethIfIntervalOutPauseFrames	Gauge32
	ethIfIntervalOverflowInUnicastFrames	Gauge32
	ethIfIntervalOverflowOutUnicastFrames	Gauge32
	ethIfIntervalOverflowInMulticastFrames	Gauge32
	ethIfIntervalOverflowOutMulticastFrames	Gauge32
	ethIfIntervalOverflowInBroadcastFrames	Gauge32
	ethIfIntervalOverflowOutBroadcastFrames	Gauge32
	ethIfIntervalOverflowInDiscardFrames	Gauge32
	ethIfIntervalOverflowOutDiscardFrames	Gauge32
	ethIfIntervalOverflowInPauseFrames	Gauge32
	ethIfIntervalOverflowOutPauseFrames	Gauge32

EthIfPerfEntry
SEQUENCE
	ethIfPerfInOkFrames	Gauge32
	ethIfPerfOutOkFrames	Gauge32
	ethIfPerfTotalCollisions	Gauge32
	ethIfPerfInOkOctets	Gauge32

RadMepEntry
SEQUENCE
	radOamIdx1	Unsigned32
	radOamEvcIdx	Unsigned32
	radMepIdx	Unsigned32
	radMepRowStatus	RowStatus
	radMepLocalMepId	Unsigned32
	radMepRemoteMepId	Unsigned32
	radMepOamMode	INTEGER
	radMepContinuityVerMode	INTEGER
	radMepMeLevel	Unsigned32
	radMepOamDestAddrType	INTEGER
	radMepOamDestMacAddr	MacAddress
	radMepDefaultPriority	Unsigned32
	radMepCcStatus	INTEGER
	radMepOamProtocol	INTEGER
	radMepMdId	Unsigned32
	radMepMaFormat	INTEGER
	radMepMaName	OCTET STRING
	radMepSpVlanId	Unsigned32
	radMepCcInterval	INTEGER
	radMepTransmitLbmDestMacAddress	MacAddress
	radMepTransmitLbmDestMepId	Unsigned32
	radMepTransmitLbmDestIsMepId	INTEGER
	radMepTransmitLbmMassages	Integer32
	radMepTransmitLbmVlanPriority	Unsigned32
	radMepTransmitLbmVlanDropEnable	INTEGER
	radMepLbrIn	Counter32
	radMepLbrInOutOfOrder	Counter32
	radMepLbmOut	Counter32
	radMepTransmitLtmTargetMacAddress	MacAddress
	radMepTransmitLtmTargetMepId	Unsigned32
	radMepTransmitLtmTargetIsMepId	INTEGER
	radMepTransmitLtmTtl	Unsigned32
	radMepTransmitLtmActivationCmd	INTEGER

EthOamServiceEntry
SEQUENCE
	ethOamServiceIdx	Unsigned32
	ethOamServiceRowStatus	RowStatus
	ethOamServicePriority	Unsigned32
	ethOamServicePmEnable	INTEGER
	ethOamServiceFrameLossRatioThresh	Integer32
	ethOamServiceDelayThresh	Integer32
	ethOamServiceDelayVarThresh	Integer32
	ethOamServiceUnavailRatioThresh	Integer32
	ethOamServiceTxFrames	Counter32
	ethOamServiceOverflowTxFrames	Counter32
	ethOamServiceFrameLoss	Counter32
	ethOamServiceOverflowFrameLoss	Counter32
	ethOamServiceFrameLossRatio	Unsigned32
	ethOamServiceElapsedTime	Counter32
	ethOamServiceUnavailSec	Counter32
	ethOamServiceUnavailRatio	Unsigned32
	ethOamServiceFramesAboveDelay	Counter32
	ethOamServiceOverflowFramesAboveDelay	Counter32
	ethOamServiceFramesAboveDelayVar	Counter32
	ethOamServiceOverflowFramesAboveDelayVar	Counter32

EthOamSvcCurrentStatEntry
SEQUENCE
	ethOamSvcCurrFramesAboveDelayThresh	PerfCurrentCount
	ethOamSvcCurrFramesBelowDelayThresh	PerfCurrentCount
	ethOamSvcCurrFramesAboveDVarThresh	PerfCurrentCount
	ethOamSvcCurrFramesBelowDVarThresh	PerfCurrentCount
	ethOamSvcCurrFramesTxCounter	PerfCurrentCount
	ethOamSvcCurrFramesLossCounter	PerfCurrentCount
	ethOamSvcCurrMinRoundTripDelay	Unsigned32
	ethOamSvcCurrMaxRoundTripDelay	Unsigned32
	ethOamSvcCurrAvgRoundTripDelay	Unsigned32
	ethOamSvcCurrMaxRoundTripDVar	Unsigned32
	ethOamSvcCurrAvgRoundTripDVar	Unsigned32
	ethOamSvcCurrElapsedTime	Integer32
	ethOamSvcCurrUnavailSec	PerfCurrentCount

EthOamSvcIntervalEntry
SEQUENCE
	ethOamSvcIntervalNum	Integer32
	ethOamSvcIntervalFramesAboveDelayThresh	PerfIntervalCount
	ethOamSvcIntervalFramesBelowDelayThresh	PerfIntervalCount
	ethOamSvcIntervalFramesAboveDVarThresh	PerfIntervalCount
	ethOamSvcIntervalFramesBelowDVarThresh	PerfIntervalCount
	ethOamSvcIntervalFramesTxCounter	PerfIntervalCount
	ethOamSvcIntervalFramesLossCounter	PerfIntervalCount
	ethOamSvcIntervalMinRoundTripDelay	Unsigned32
	ethOamSvcIntervalMaxRoundTripDelay	Unsigned32
	ethOamSvcIntervalAvgRoundTripDelay	Unsigned32
	ethOamSvcIntervalMaxRoundTripDVar	Unsigned32
	ethOamSvcIntervalAvgRoundTripDVar	Unsigned32
	ethOamSvcIntervalUnavailSec	PerfIntervalCount

EthOamSvcTotalEntry
SEQUENCE
	ethOamSvcTotalFramesAboveDelayThresh	PerfTotalCount
	ethOamSvcTotalFramesBelowDelayThresh	PerfTotalCount
	ethOamSvcTotalFramesAboveDVarThresh	PerfTotalCount
	ethOamSvcTotalFramesBelowDVarThresh	PerfTotalCount
	ethOamSvcTotalFramesTxCounter	PerfTotalCount
	ethOamSvcTotalFramesLossCounter	PerfTotalCount
	ethOamSvcTotalMinRoundTripDelay	Unsigned32
	ethOamSvcTotalMaxRoundTripDelay	Unsigned32
	ethOamSvcTotalAvgRoundTripDelay	Unsigned32
	ethOamSvcTotalMaxRoundTripDVar	Unsigned32
	ethOamSvcTotalAvgRoundTripDVar	Unsigned32
	ethOamSvcTotalUnavailSec	PerfTotalCount

RadMdEntry
SEQUENCE
	radMdIndex	Unsigned32
	radMdFormat	INTEGER
	radMdName	OCTET STRING
	radMdRowStatus	RowStatus

RadMepLtrEntry
SEQUENCE
	radMepLtrReceiveOrder	Unsigned32
	radMepLtrTtl	Unsigned32
	radMepLtrMacAddr	MacAddress
	radMepLtrRelay	INTEGER
	radMepLtrIngress	INTEGER
	radMepLtrIngressPortIdSubtype	LldpPortIdSubtype
	radMepLtrIngressPortId	OCTET STRING
	radMepLtrEgress	INTEGER
	radMepLtrEgressPortIdSubtype	LldpPortIdSubtype
	radMepLtrEgressPortId	OCTET STRING

RadMepCcStatusEntry
SEQUENCE
	radMepRemoteMepIdx	Unsigned32
	radMepCcStatusRemMepId	Unsigned32
	radMepCcStat	INTEGER
	radMepCcStatusMacAddr	MacAddress

Dot1agXCfmMdEntry
SEQUENCE
	dot1agXCfmMdProtocol	INTEGER

Dot1agXCfmMepEntry
SEQUENCE
	dot1agXCfmMepContinuityVerMode	INTEGER
	dot1agXCfmMepDestAddrType	INTEGER
	dot1agXCfmMepDestMacAddr	MacAddress

Dot1agXCfmMepDbEntry
SEQUENCE
	dot1agXCfmMepCcStat	INTEGER

EthIfRingEntry
SEQUENCE
	ethIfRingIdx	Unsigned32
	ethIfRingAdminStatus	INTEGER
	ethIfRingPorts	PortList
	ethIfRingOperStatus	INTEGER
	ethIfRingKeepAliveInterval	Unsigned32
	ethIfRingKeepAliveThresh	Unsigned32
	ethIfRingKeepAliveVlanId	Unsigned32
	ethIfRingMultiCastVlanId	Unsigned32
	ethIfRingRowStatus	INTEGER

EthIfStormEntry
SEQUENCE
	ethIfStormCnfgIdx	Unsigned32
	ethIfStormIfIdx	Unsigned32
	ethIfStormDirection	INTEGER
	ethIfStormPacketType	BITS
	ethIfStormCtrlEnable	INTEGER
	ethIfStormMaxRate	Unsigned32

Dot3OamDescrEntry
SEQUENCE
	dot3OamDescrId	Unsigned32
	dot3OamDescrRowStatus	RowStatus
	dot3OamDescrMode	INTEGER
	dot3OamDescrLbRxOperation	INTEGER
	dot3OamDescrRateLimit	Unsigned32

Dot3OamXEntry
SEQUENCE
	dot3OamXDescrId	Unsigned32
	dot3OamXPeerState	INTEGER

EthIfSrcMacCtrlEntry
SEQUENCE
	ethIfSrcMacCtrlIndex	Unsigned32
	ethIfSrcMacCtrlIdx2	Unsigned32
	ethIfSrcMacCtrl	INTEGER
	ethIfSrcMacCtrlMaxPermitAddr	Unsigned32
	ethIfSrcMacCtrlCurNumPermitAddr	Unsigned32
	ethIfSrcMacCtrlFlushAddrCmd	INTEGER
	ethIfSrcMacCtrlAging	Unsigned32
	ethIfSrcMacCtrlLocking	INTEGER
	ethIfSrcMacCtrlViolationAction	INTEGER
	ethIfSrcMacCtrlLastViolatingAddr	MacAddress
	ethIfSrcMacCtrlPortStatus	INTEGER

EthIfSrcMacCtrlAddrEntry
SEQUENCE
	ethIfSrcMacCtrlAddrIndex	Unsigned32
	ethIfSrcMacCtrlAddr	MacAddress
	ethIfSrcMacCtrlAddrIdx3	Unsigned32
	ethIfSrcMacCtrlAddrRowStatus	INTEGER
	ethIfSrcMacCtrlAddrStatus	INTEGER

Defined Values

rad		1.3.6.1.4.1.164
OBJECT IDENTIFIER

radTokenRing		1.3.6.1.4.1.164.1
OBJECT IDENTIFIER

radFddi		1.3.6.1.4.1.164.2
OBJECT IDENTIFIER

radWan		1.3.6.1.4.1.164.3
OBJECT IDENTIFIER

radBridges		1.3.6.1.4.1.164.4
OBJECT IDENTIFIER

radConverters		1.3.6.1.4.1.164.5
OBJECT IDENTIFIER

radGen		1.3.6.1.4.1.164.6
OBJECT IDENTIFIER

radStkHub		1.3.6.1.4.1.164.7
OBJECT IDENTIFIER

radAtm		1.3.6.1.4.1.164.12
OBJECT IDENTIFIER

radRouter		1.3.6.1.4.1.164.11
OBJECT IDENTIFIER

rtrBridge		1.3.6.1.4.1.164.11.7
OBJECT IDENTIFIER

systems		1.3.6.1.4.1.164.6.1
OBJECT IDENTIFIER

radSysTR		1.3.6.1.4.1.164.6.1.1
OBJECT IDENTIFIER

radRADring		1.3.6.1.4.1.164.6.1.1.1
OBJECT IDENTIFIER

radTMA		1.3.6.1.4.1.164.6.1.1.2
OBJECT IDENTIFIER

radRingMonitor		1.3.6.1.4.1.164.6.1.1.3
OBJECT IDENTIFIER

radSysFddi		1.3.6.1.4.1.164.6.1.2
OBJECT IDENTIFIER

radFDX100		1.3.6.1.4.1.164.6.1.2.1
OBJECT IDENTIFIER

radSysWan		1.3.6.1.4.1.164.6.1.3
OBJECT IDENTIFIER

radSysWanEvents		1.3.6.1.4.1.164.6.1.3.0
The events for RAD Wan products.
Status: current	Access: read-only
OBJECT-IDENTITY

radMP2100		1.3.6.1.4.1.164.6.1.3.1
OBJECT IDENTIFIER

radMP2104		1.3.6.1.4.1.164.6.1.3.2
OBJECT IDENTIFIER

radMP2100B		1.3.6.1.4.1.164.6.1.3.3
OBJECT IDENTIFIER

radMP2100F		1.3.6.1.4.1.164.6.1.3.4
OBJECT IDENTIFIER

radMP2100H		1.3.6.1.4.1.164.6.1.3.5
OBJECT IDENTIFIER

radMP2104H		1.3.6.1.4.1.164.6.1.3.6
OBJECT IDENTIFIER

radMP2200B		1.3.6.1.4.1.164.6.1.3.7
OBJECT IDENTIFIER

radMP2200F		1.3.6.1.4.1.164.6.1.3.8
OBJECT IDENTIFIER

radMX3000		1.3.6.1.4.1.164.6.1.3.9
OBJECT IDENTIFIER

radMX3004		1.3.6.1.4.1.164.6.1.3.10
OBJECT IDENTIFIER

radMX30		1.3.6.1.4.1.164.6.1.3.11
OBJECT IDENTIFIER

radMX300		1.3.6.1.4.1.164.6.1.3.12
OBJECT IDENTIFIER

radVOIP		1.3.6.1.4.1.164.6.1.3.13
OBJECT IDENTIFIER

radKM2100		1.3.6.1.4.1.164.6.1.3.15
OBJECT IDENTIFIER

radKM2104		1.3.6.1.4.1.164.6.1.3.16
OBJECT IDENTIFIER

radDXC30		1.3.6.1.4.1.164.6.1.3.20
OBJECT IDENTIFIER

radDXC10A		1.3.6.1.4.1.164.6.1.3.21
OBJECT IDENTIFIER

radDXC8R		1.3.6.1.4.1.164.6.1.3.22
OBJECT IDENTIFIER

radDXC30E		1.3.6.1.4.1.164.6.1.3.23
OBJECT IDENTIFIER

radDXC3000		1.3.6.1.4.1.164.6.1.3.24
OBJECT IDENTIFIER

radDXC8RNew		1.3.6.1.4.1.164.6.1.3.25
OBJECT IDENTIFIER

radFcdT1LC		1.3.6.1.4.1.164.6.1.3.26
OBJECT IDENTIFIER

radFcdE1LC		1.3.6.1.4.1.164.6.1.3.27
OBJECT IDENTIFIER

radFcdT1L		1.3.6.1.4.1.164.6.1.3.28
OBJECT IDENTIFIER

radFcdE1L		1.3.6.1.4.1.164.6.1.3.29
OBJECT IDENTIFIER

radFcdT1		1.3.6.1.4.1.164.6.1.3.30
OBJECT IDENTIFIER

radFcdE1		1.3.6.1.4.1.164.6.1.3.31
OBJECT IDENTIFIER

radFcdE1I		1.3.6.1.4.1.164.6.1.3.32
OBJECT IDENTIFIER

radFcdT1M		1.3.6.1.4.1.164.6.1.3.33
OBJECT IDENTIFIER

radFcdE1M		1.3.6.1.4.1.164.6.1.3.34
OBJECT IDENTIFIER

radFcdIP		1.3.6.1.4.1.164.6.1.3.35
OBJECT IDENTIFIER

radFcdT1A		1.3.6.1.4.1.164.6.1.3.36
OBJECT IDENTIFIER

radFcdE1A		1.3.6.1.4.1.164.6.1.3.37
OBJECT IDENTIFIER

radFcdW		1.3.6.1.4.1.164.6.1.3.38
OBJECT IDENTIFIER

radFcdSTM		1.3.6.1.4.1.164.6.1.3.39
OBJECT IDENTIFIER

radHtuE1Sa		1.3.6.1.4.1.164.6.1.3.40
OBJECT IDENTIFIER

radHtuE1		1.3.6.1.4.1.164.6.1.3.41
OBJECT IDENTIFIER

radHtu2Sa		1.3.6.1.4.1.164.6.1.3.42
OBJECT IDENTIFIER

radHtu2		1.3.6.1.4.1.164.6.1.3.43
OBJECT IDENTIFIER

radAsmi450R768Sa		1.3.6.1.4.1.164.6.1.3.44
OBJECT IDENTIFIER

radAsmi450R768		1.3.6.1.4.1.164.6.1.3.45
OBJECT IDENTIFIER

radAsmi450R1152Sa		1.3.6.1.4.1.164.6.1.3.46
OBJECT IDENTIFIER

radAsmi450R1152		1.3.6.1.4.1.164.6.1.3.47
OBJECT IDENTIFIER

radLrs12F		1.3.6.1.4.1.164.6.1.3.48
OBJECT IDENTIFIER

radLrs12B		1.3.6.1.4.1.164.6.1.3.49
OBJECT IDENTIFIER

radLrs52		1.3.6.1.4.1.164.6.1.3.50
OBJECT IDENTIFIER

radHcdE1Sa		1.3.6.1.4.1.164.6.1.3.51
OBJECT IDENTIFIER

radHcdE1		1.3.6.1.4.1.164.6.1.3.52
OBJECT IDENTIFIER

radHtuT1Sa		1.3.6.1.4.1.164.6.1.3.53
OBJECT IDENTIFIER

radHtuT1		1.3.6.1.4.1.164.6.1.3.54
OBJECT IDENTIFIER

radOptimux4E1		1.3.6.1.4.1.164.6.1.3.55
OBJECT IDENTIFIER

radOptimux4T1		1.3.6.1.4.1.164.6.1.3.56
OBJECT IDENTIFIER

radOptimuxXLE1		1.3.6.1.4.1.164.6.1.3.57
OBJECT IDENTIFIER

radOptimuxXLT1		1.3.6.1.4.1.164.6.1.3.58
OBJECT IDENTIFIER

radOptimuxXL16E1		1.3.6.1.4.1.164.6.1.3.59
OBJECT IDENTIFIER

radImx64		1.3.6.1.4.1.164.6.1.3.60
OBJECT IDENTIFIER

radImx6L		1.3.6.1.4.1.164.6.1.3.61
OBJECT IDENTIFIER

radImx2		1.3.6.1.4.1.164.6.1.3.62
OBJECT IDENTIFIER

radImx4T1		1.3.6.1.4.1.164.6.1.3.63
OBJECT IDENTIFIER

radImx4E1		1.3.6.1.4.1.164.6.1.3.64
OBJECT IDENTIFIER

radImx2T1E1		1.3.6.1.4.1.164.6.1.3.65
OBJECT IDENTIFIER

radImxi4		1.3.6.1.4.1.164.6.1.3.66
OBJECT IDENTIFIER

radOptimux155		1.3.6.1.4.1.164.6.1.3.67
OBJECT IDENTIFIER

radOptimux4T1L		1.3.6.1.4.1.164.6.1.3.68
OBJECT IDENTIFIER

radOptimux4E1L		1.3.6.1.4.1.164.6.1.3.69
OBJECT IDENTIFIER

radHtuE1SaV2		1.3.6.1.4.1.164.6.1.3.70
OBJECT IDENTIFIER

radHtuE1V2		1.3.6.1.4.1.164.6.1.3.71
OBJECT IDENTIFIER

radFomiE3		1.3.6.1.4.1.164.6.1.3.72
OBJECT IDENTIFIER

radFomiT3		1.3.6.1.4.1.164.6.1.3.73
OBJECT IDENTIFIER

radOpt4E1C		1.3.6.1.4.1.164.6.1.3.74
OBJECT IDENTIFIER

radOpt4T1C		1.3.6.1.4.1.164.6.1.3.75
OBJECT IDENTIFIER

radPrbiE3		1.3.6.1.4.1.164.6.1.3.76
OBJECT IDENTIFIER

radPrbiT3		1.3.6.1.4.1.164.6.1.3.77
OBJECT IDENTIFIER

radHcd4Sa		1.3.6.1.4.1.164.6.1.3.78
OBJECT IDENTIFIER

radOptimuxT3		1.3.6.1.4.1.164.6.1.3.79
OBJECT IDENTIFIER

radFRmon		1.3.6.1.4.1.164.6.1.3.80
OBJECT IDENTIFIER

radIpMux4		1.3.6.1.4.1.164.6.1.3.81
OBJECT IDENTIFIER

radIpMux1		1.3.6.1.4.1.164.6.1.3.82
OBJECT IDENTIFIER

radIpMux16		1.3.6.1.4.1.164.6.1.3.83
OBJECT IDENTIFIER

radIpMux1E		1.3.6.1.4.1.164.6.1.3.84
OBJECT IDENTIFIER

radVmux2100		1.3.6.1.4.1.164.6.1.3.85
OBJECT IDENTIFIER

radMP104		1.3.6.1.4.1.164.6.1.3.86
OBJECT IDENTIFIER

radMP204		1.3.6.1.4.1.164.6.1.3.87
OBJECT IDENTIFIER

radVmux110		1.3.6.1.4.1.164.6.1.3.88
OBJECT IDENTIFIER

radFcd155		1.3.6.1.4.1.164.6.1.3.90
OBJECT IDENTIFIER

radIpMux8		1.3.6.1.4.1.164.6.1.3.91
OBJECT IDENTIFIER

radOptimux155DS3		1.3.6.1.4.1.164.6.1.3.92
OBJECT IDENTIFIER

radOptimuxT3L		1.3.6.1.4.1.164.6.1.3.93
OBJECT IDENTIFIER

radGmux2000		1.3.6.1.4.1.164.6.1.3.94
OBJECT IDENTIFIER

radOp16E1L		1.3.6.1.4.1.164.6.1.3.95
OBJECT IDENTIFIER

radOp16E1LS		1.3.6.1.4.1.164.6.1.3.96
OBJECT IDENTIFIER

radPRBm20		1.3.6.1.4.1.164.6.1.3.97
OBJECT IDENTIFIER

radPRBm22		1.3.6.1.4.1.164.6.1.3.98
OBJECT IDENTIFIER

radAsmi52A		1.3.6.1.4.1.164.6.1.3.99
OBJECT IDENTIFIER

radOpXLE1		1.3.6.1.4.1.164.6.1.3.100
OBJECT IDENTIFIER

radOpXLT1		1.3.6.1.4.1.164.6.1.3.101
OBJECT IDENTIFIER

radOpXL16E1		1.3.6.1.4.1.164.6.1.3.102
OBJECT IDENTIFIER

radOp4E1		1.3.6.1.4.1.164.6.1.3.103
OBJECT IDENTIFIER

radOp4T1		1.3.6.1.4.1.164.6.1.3.104
OBJECT IDENTIFIER

radDxc4		1.3.6.1.4.1.164.6.1.3.105
OBJECT IDENTIFIER

radIpMux11		1.3.6.1.4.1.164.6.1.3.106
OBJECT IDENTIFIER

radIpMux14		1.3.6.1.4.1.164.6.1.3.107
OBJECT IDENTIFIER

radOp1550		1.3.6.1.4.1.164.6.1.3.108
OBJECT IDENTIFIER

radFdsl101		1.3.6.1.4.1.164.6.1.3.110
OBJECT IDENTIFIER

radFdsl201		1.3.6.1.4.1.164.6.1.3.111
OBJECT IDENTIFIER

radVmux120		1.3.6.1.4.1.164.6.1.3.112
OBJECT IDENTIFIER

radVmux2200		1.3.6.1.4.1.164.6.1.3.113
OBJECT IDENTIFIER

radVmux400		1.3.6.1.4.1.164.6.1.3.114
OBJECT IDENTIFIER

radIpMux116		1.3.6.1.4.1.164.6.1.3.115
OBJECT IDENTIFIER

radOp4E1LNew		1.3.6.1.4.1.164.6.1.3.116
OBJECT IDENTIFIER

radOp4T1LNew		1.3.6.1.4.1.164.6.1.3.117
OBJECT IDENTIFIER

radFcd155E		1.3.6.1.4.1.164.6.1.3.118
OBJECT IDENTIFIER

radFcd155ES		1.3.6.1.4.1.164.6.1.3.119
OBJECT IDENTIFIER

radMP4100		1.3.6.1.4.1.164.6.1.3.120
OBJECT IDENTIFIER

radAsmi52L		1.3.6.1.4.1.164.6.1.3.121
OBJECT IDENTIFIER

radVmux210		1.3.6.1.4.1.164.6.1.3.122
OBJECT IDENTIFIER

radOp34E1		1.3.6.1.4.1.164.6.1.3.123
OBJECT IDENTIFIER

radVmux312		1.3.6.1.4.1.164.6.1.3.124
OBJECT IDENTIFIER

radVmux404		1.3.6.1.4.1.164.6.1.3.125
OBJECT IDENTIFIER

radVmux420		1.3.6.1.4.1.164.6.1.3.126
OBJECT IDENTIFIER

radIpMux12		1.3.6.1.4.1.164.6.1.3.127
OBJECT IDENTIFIER

radOptimux4E1V3dot5		1.3.6.1.4.1.164.6.1.3.128
OBJECT IDENTIFIER

radOptimux4E1Mar06		1.3.6.1.4.1.164.6.1.3.129
OBJECT IDENTIFIER

radFcd155EwAPS		1.3.6.1.4.1.164.6.1.3.130
OBJECT IDENTIFIER

radOptimux4T1Mar06		1.3.6.1.4.1.164.6.1.3.131
OBJECT IDENTIFIER

radFcd155EwAPS2pdh		1.3.6.1.4.1.164.6.1.3.132
OBJECT IDENTIFIER

radVmux320		1.3.6.1.4.1.164.6.1.3.133
OBJECT IDENTIFIER

radMP2100VoIP		1.3.6.1.4.1.164.6.1.3.134
OBJECT IDENTIFIER

radMP2104VoIP		1.3.6.1.4.1.164.6.1.3.135
OBJECT IDENTIFIER

radIpMux24		1.3.6.1.4.1.164.6.1.3.136
OBJECT IDENTIFIER

radOp4E1NG1		1.3.6.1.4.1.164.6.1.3.137
OBJECT IDENTIFIER

radOp4T1NG1		1.3.6.1.4.1.164.6.1.3.138
OBJECT IDENTIFIER

radOp25		1.3.6.1.4.1.164.6.1.3.139
OBJECT IDENTIFIER

radAsmi54		1.3.6.1.4.1.164.6.1.3.140
OBJECT IDENTIFIER

radVmux314		1.3.6.1.4.1.164.6.1.3.141
OBJECT IDENTIFIER

radFcd622		1.3.6.1.4.1.164.6.1.3.142
OBJECT IDENTIFIER

radLrs22		1.3.6.1.4.1.164.6.1.3.143
OBJECT IDENTIFIER

radUNT20E1		1.3.6.1.4.1.164.6.1.3.144
OBJECT IDENTIFIER

radIpMux2L		1.3.6.1.4.1.164.6.1.3.145
OBJECT IDENTIFIER

radUNT20Fcd		1.3.6.1.4.1.164.6.1.3.146
OBJECT IDENTIFIER

radIpMux216		1.3.6.1.4.1.164.6.1.3.147
OBJECT IDENTIFIER

radLrs102		1.3.6.1.4.1.164.6.1.3.148
OBJECT IDENTIFIER

radGmux2004		1.3.6.1.4.1.164.6.1.3.149
OBJECT IDENTIFIER

radLrs102unbal		1.3.6.1.4.1.164.6.1.3.150
OBJECT IDENTIFIER

radLrs16		1.3.6.1.4.1.164.6.1.3.151
OBJECT IDENTIFIER

radVmux405		1.3.6.1.4.1.164.6.1.3.152
OBJECT IDENTIFIER

radVmux425		1.3.6.1.4.1.164.6.1.3.153
OBJECT IDENTIFIER

radMiniCVS		1.3.6.1.4.1.164.6.1.3.154
OBJECT IDENTIFIER

radSysBRG		1.3.6.1.4.1.164.6.1.4
OBJECT IDENTIFIER

radTRE1		1.3.6.1.4.1.164.6.1.4.1
OBJECT IDENTIFIER

radTRE1D		1.3.6.1.4.1.164.6.1.4.2
OBJECT IDENTIFIER

radTRE8		1.3.6.1.4.1.164.6.1.4.3
OBJECT IDENTIFIER

radTRE8D		1.3.6.1.4.1.164.6.1.4.4
OBJECT IDENTIFIER

radMBE1		1.3.6.1.4.1.164.6.1.4.5
OBJECT IDENTIFIER

radMBE1D		1.3.6.1.4.1.164.6.1.4.6
OBJECT IDENTIFIER

radMBE8		1.3.6.1.4.1.164.6.1.4.7
OBJECT IDENTIFIER

radMBE8D		1.3.6.1.4.1.164.6.1.4.8
OBJECT IDENTIFIER

radMLBT		1.3.6.1.4.1.164.6.1.4.9
OBJECT IDENTIFIER

radFEB4DAS		1.3.6.1.4.1.164.6.1.4.10
OBJECT IDENTIFIER

radTrimBrg10		1.3.6.1.4.1.164.6.1.4.11
OBJECT IDENTIFIER

radTrimBrg16		1.3.6.1.4.1.164.6.1.4.12
OBJECT IDENTIFIER

radRRTRE8		1.3.6.1.4.1.164.6.1.4.13
OBJECT IDENTIFIER

radRRTRE8D		1.3.6.1.4.1.164.6.1.4.14
OBJECT IDENTIFIER

radRRMLBT		1.3.6.1.4.1.164.6.1.4.15
OBJECT IDENTIFIER

radRRMLBTF		1.3.6.1.4.1.164.6.1.4.16
OBJECT IDENTIFIER

radRRTRE1D		1.3.6.1.4.1.164.6.1.4.17
OBJECT IDENTIFIER

radTRERAS		1.3.6.1.4.1.164.6.1.4.18
OBJECT IDENTIFIER

radTRERASa		1.3.6.1.4.1.164.6.1.4.19
OBJECT IDENTIFIER

radMBERAS		1.3.6.1.4.1.164.6.1.4.20
OBJECT IDENTIFIER

radMBERASa		1.3.6.1.4.1.164.6.1.4.21
OBJECT IDENTIFIER

radFEB4FDX		1.3.6.1.4.1.164.6.1.4.22
OBJECT IDENTIFIER

radFEB4SAS		1.3.6.1.4.1.164.6.1.4.23
OBJECT IDENTIFIER

radRRFTBDAS		1.3.6.1.4.1.164.6.1.4.24
OBJECT IDENTIFIER

radRRFTBSAS		1.3.6.1.4.1.164.6.1.4.25
OBJECT IDENTIFIER

radFTBDAS		1.3.6.1.4.1.164.6.1.4.26
OBJECT IDENTIFIER

radFTBSAS		1.3.6.1.4.1.164.6.1.4.27
OBJECT IDENTIFIER

radFastWay100		1.3.6.1.4.1.164.6.1.4.28
OBJECT IDENTIFIER

radSysCnvrtr		1.3.6.1.4.1.164.6.1.5
OBJECT IDENTIFIER

radSTC1		1.3.6.1.4.1.164.6.1.5.1
OBJECT IDENTIFIER

radSTC2		1.3.6.1.4.1.164.6.1.5.3
OBJECT IDENTIFIER

radSTC1UDP		1.3.6.1.4.1.164.6.1.5.4
OBJECT IDENTIFIER

radSTC2UDP		1.3.6.1.4.1.164.6.1.5.6
OBJECT IDENTIFIER

radFTC1		1.3.6.1.4.1.164.6.1.5.10
OBJECT IDENTIFIER

radFTC2		1.3.6.1.4.1.164.6.1.5.12
OBJECT IDENTIFIER

radFTC1UDP		1.3.6.1.4.1.164.6.1.5.13
OBJECT IDENTIFIER

radFTC2UDP		1.3.6.1.4.1.164.6.1.5.15
OBJECT IDENTIFIER

radSEC1		1.3.6.1.4.1.164.6.1.5.20
OBJECT IDENTIFIER

radSEC2		1.3.6.1.4.1.164.6.1.5.22
OBJECT IDENTIFIER

radSEC1UDP		1.3.6.1.4.1.164.6.1.5.23
OBJECT IDENTIFIER

radSEC2UDP		1.3.6.1.4.1.164.6.1.5.25
OBJECT IDENTIFIER

radFEC1		1.3.6.1.4.1.164.6.1.5.30
OBJECT IDENTIFIER

radFEC2		1.3.6.1.4.1.164.6.1.5.32
OBJECT IDENTIFIER

radFEC1UDP		1.3.6.1.4.1.164.6.1.5.33
OBJECT IDENTIFIER

radFEC2UDP		1.3.6.1.4.1.164.6.1.5.35
OBJECT IDENTIFIER

radRIC155		1.3.6.1.4.1.164.6.1.5.36
OBJECT IDENTIFIER

radRICE1		1.3.6.1.4.1.164.6.1.5.37
OBJECT IDENTIFIER

radETX102		1.3.6.1.4.1.164.6.1.5.38
OBJECT IDENTIFIER

radRIC155GE		1.3.6.1.4.1.164.6.1.5.39
OBJECT IDENTIFIER

radRiciT3		1.3.6.1.4.1.164.6.1.5.40
OBJECT IDENTIFIER

radRiciE3		1.3.6.1.4.1.164.6.1.5.41
OBJECT IDENTIFIER

radRiciT1		1.3.6.1.4.1.164.6.1.5.42
OBJECT IDENTIFIER

radETX202		1.3.6.1.4.1.164.6.1.5.43
OBJECT IDENTIFIER

radETX105		1.3.6.1.4.1.164.6.1.5.44
OBJECT IDENTIFIER

radETX205		1.3.6.1.4.1.164.6.1.5.45
OBJECT IDENTIFIER

radRiciSE		1.3.6.1.4.1.164.6.1.5.46
OBJECT IDENTIFIER

radRIC622GE		1.3.6.1.4.1.164.6.1.5.47
OBJECT IDENTIFIER

radSPH		1.3.6.1.4.1.164.6.1.5.48
OBJECT IDENTIFIER

radMiricE1T1		1.3.6.1.4.1.164.6.1.5.49
OBJECT IDENTIFIER

radMiricE3T3		1.3.6.1.4.1.164.6.1.5.50
OBJECT IDENTIFIER

radEthAccess		1.3.6.1.4.1.164.6.1.6
OBJECT IDENTIFIER

radETX510		1.3.6.1.4.1.164.6.1.6.1
OBJECT IDENTIFIER

radEGate100		1.3.6.1.4.1.164.6.1.6.2
OBJECT IDENTIFIER

radEGate20		1.3.6.1.4.1.164.6.1.6.3
OBJECT IDENTIFIER

radRici8E1		1.3.6.1.4.1.164.6.1.6.4
OBJECT IDENTIFIER

radRici8T1		1.3.6.1.4.1.164.6.1.6.5
OBJECT IDENTIFIER

radRici4E1		1.3.6.1.4.1.164.6.1.6.6
OBJECT IDENTIFIER

radRici4T1		1.3.6.1.4.1.164.6.1.6.7
OBJECT IDENTIFIER

radIMXI4		1.3.6.1.4.1.164.6.1.6.8
OBJECT IDENTIFIER

radETX550		1.3.6.1.4.1.164.6.1.6.9
OBJECT IDENTIFIER

radRici16		1.3.6.1.4.1.164.6.1.6.10
OBJECT IDENTIFIER

radETX102A		1.3.6.1.4.1.164.6.1.6.11
OBJECT IDENTIFIER

radETX202A		1.3.6.1.4.1.164.6.1.6.12
OBJECT IDENTIFIER

radETX201A		1.3.6.1.4.1.164.6.1.6.13
OBJECT IDENTIFIER

radETX201		1.3.6.1.4.1.164.6.1.6.14
OBJECT IDENTIFIER

radUNT20Ric		1.3.6.1.4.1.164.6.1.6.15
OBJECT IDENTIFIER

radRici4E1L		1.3.6.1.4.1.164.6.1.6.16
OBJECT IDENTIFIER

radRici8E1L		1.3.6.1.4.1.164.6.1.6.17
OBJECT IDENTIFIER

radRici155GE		1.3.6.1.4.1.164.6.1.6.18
OBJECT IDENTIFIER

radRici622GE		1.3.6.1.4.1.164.6.1.6.19
OBJECT IDENTIFIER

radETX208		1.3.6.1.4.1.164.6.1.6.20
OBJECT IDENTIFIER

radETX202AW		1.3.6.1.4.1.164.6.1.6.21
OBJECT IDENTIFIER

radETX102H		1.3.6.1.4.1.164.6.1.6.22
OBJECT IDENTIFIER

radETX202H		1.3.6.1.4.1.164.6.1.6.23
OBJECT IDENTIFIER

radSysStkHub		1.3.6.1.4.1.164.6.1.7
OBJECT IDENTIFIER

radRBHE		1.3.6.1.4.1.164.6.1.7.1
OBJECT IDENTIFIER

radRBHT		1.3.6.1.4.1.164.6.1.7.2
OBJECT IDENTIFIER

radRBHEEvents		1.3.6.1.4.1.164.6.1.7.1.0
The events for RAD Stackable products.
Status: current	Access: read-only
OBJECT-IDENTITY

radRBHTEvents		1.3.6.1.4.1.164.6.1.7.2.0
The events for RAD Stackable products.
Status: current	Access: read-only
OBJECT-IDENTITY

radETS4fddiDAS		1.3.6.1.4.1.164.6.1.7.3
OBJECT IDENTIFIER

radETS4fddiSAS		1.3.6.1.4.1.164.6.1.7.4
OBJECT IDENTIFIER

radSAHEMX		1.3.6.1.4.1.164.6.1.7.5
OBJECT IDENTIFIER

radSAHTM		1.3.6.1.4.1.164.6.1.7.6
OBJECT IDENTIFIER

radETS4		1.3.6.1.4.1.164.6.1.7.7
OBJECT IDENTIFIER

radSAHEMU		1.3.6.1.4.1.164.6.1.7.8
OBJECT IDENTIFIER

unknown		1.3.6.1.4.1.164.6.1.7.9
OBJECT IDENTIFIER

radSAH16Eint		1.3.6.1.4.1.164.6.1.7.10
OBJECT IDENTIFIER

radSAH16Tint		1.3.6.1.4.1.164.6.1.7.11
OBJECT IDENTIFIER

radSAH16Eext		1.3.6.1.4.1.164.6.1.7.12
OBJECT IDENTIFIER

radSAH16Text		1.3.6.1.4.1.164.6.1.7.13
OBJECT IDENTIFIER

radSysPS		1.3.6.1.4.1.164.6.1.8
OBJECT IDENTIFIER

radSysPSEvents		1.3.6.1.4.1.164.6.1.8.0
The events for RAD Packet Switch (PS) products.
Status: current	Access: read-only
OBJECT-IDENTITY

radSPS2		1.3.6.1.4.1.164.6.1.8.1
OBJECT IDENTIFIER

radSPS3		1.3.6.1.4.1.164.6.1.8.2
OBJECT IDENTIFIER

radSPS6		1.3.6.1.4.1.164.6.1.8.3
OBJECT IDENTIFIER

radSPS9		1.3.6.1.4.1.164.6.1.8.4
OBJECT IDENTIFIER

radSPS12		1.3.6.1.4.1.164.6.1.8.5
OBJECT IDENTIFIER

radAPD2		1.3.6.1.4.1.164.6.1.8.6
OBJECT IDENTIFIER

radAPD8		1.3.6.1.4.1.164.6.1.8.7
OBJECT IDENTIFIER

radAPS8		1.3.6.1.4.1.164.6.1.8.8
OBJECT IDENTIFIER

radAPS16		1.3.6.1.4.1.164.6.1.8.9
OBJECT IDENTIFIER

radAPS24		1.3.6.1.4.1.164.6.1.8.10
OBJECT IDENTIFIER

radSPS3S		1.3.6.1.4.1.164.6.1.8.11
OBJECT IDENTIFIER

radFPS8		1.3.6.1.4.1.164.6.1.8.12
OBJECT IDENTIFIER

radFPS12		1.3.6.1.4.1.164.6.1.8.13
OBJECT IDENTIFIER

radSPS3ScSL		1.3.6.1.4.1.164.6.1.8.14
OBJECT IDENTIFIER

radSPS3Sc2S		1.3.6.1.4.1.164.6.1.8.15
OBJECT IDENTIFIER

radFPS8c		1.3.6.1.4.1.164.6.1.8.16
OBJECT IDENTIFIER

radFPS4		1.3.6.1.4.1.164.6.1.8.17
OBJECT IDENTIFIER

radSPS4		1.3.6.1.4.1.164.6.1.8.18
OBJECT IDENTIFIER

radSysEth		1.3.6.1.4.1.164.6.1.9
OBJECT IDENTIFIER

radEP8T		1.3.6.1.4.1.164.6.1.9.1
OBJECT IDENTIFIER

radEP4TAUI		1.3.6.1.4.1.164.6.1.9.2
OBJECT IDENTIFIER

radEP4T2FL		1.3.6.1.4.1.164.6.1.9.3
OBJECT IDENTIFIER

radEP4TFL		1.3.6.1.4.1.164.6.1.9.4
OBJECT IDENTIFIER

radEP4FL		1.3.6.1.4.1.164.6.1.9.5
OBJECT IDENTIFIER

radEPR8T		1.3.6.1.4.1.164.6.1.9.7
OBJECT IDENTIFIER

radEPR4TAUI		1.3.6.1.4.1.164.6.1.9.8
OBJECT IDENTIFIER

radEPR4T2FL		1.3.6.1.4.1.164.6.1.9.9
OBJECT IDENTIFIER

radEPR4TFL		1.3.6.1.4.1.164.6.1.9.10
OBJECT IDENTIFIER

radEPR4FL		1.3.6.1.4.1.164.6.1.9.11
OBJECT IDENTIFIER

radSysRtr		1.3.6.1.4.1.164.6.1.11
OBJECT IDENTIFIER

radSysRtrEvents		1.3.6.1.4.1.164.6.1.11.0
The events for RAD Router products.
Status: current	Access: read-only
OBJECT-IDENTITY

radRTED		1.3.6.1.4.1.164.6.1.11.1
OBJECT IDENTIFIER

radRTEM		1.3.6.1.4.1.164.6.1.11.2
OBJECT IDENTIFIER

radRTEC		1.3.6.1.4.1.164.6.1.11.3
OBJECT IDENTIFIER

radWebRanger		1.3.6.1.4.1.164.6.1.11.4
OBJECT IDENTIFIER

radTinyRouter		1.3.6.1.4.1.164.6.1.11.5
OBJECT IDENTIFIER

radLA240		1.3.6.1.4.1.164.6.1.11.6
OBJECT IDENTIFIER

radSuperLan		1.3.6.1.4.1.164.6.1.11.7
OBJECT IDENTIFIER

radLA240I		1.3.6.1.4.1.164.6.1.11.8
OBJECT IDENTIFIER

radFcdIsdn		1.3.6.1.4.1.164.6.1.11.9
OBJECT IDENTIFIER

radEFcdIp		1.3.6.1.4.1.164.6.1.11.10
OBJECT IDENTIFIER

radFcdIpD		1.3.6.1.4.1.164.6.1.11.11
OBJECT IDENTIFIER

radFcdIpM		1.3.6.1.4.1.164.6.1.11.12
OBJECT IDENTIFIER

radFcdIpL		1.3.6.1.4.1.164.6.1.11.13
OBJECT IDENTIFIER

radSysAtm		1.3.6.1.4.1.164.6.1.12
OBJECT IDENTIFIER

radSysAtmEvents		1.3.6.1.4.1.164.6.1.12.0
The events for RAD ATM products.
Status: current	Access: read-only
OBJECT-IDENTITY

radStarSwitch		1.3.6.1.4.1.164.6.1.12.1
OBJECT IDENTIFIER

radStarSwitchATM25		1.3.6.1.4.1.164.6.1.12.1.1
OBJECT IDENTIFIER

radStarSwitchATM25L		1.3.6.1.4.1.164.6.1.12.1.2
OBJECT IDENTIFIER

radStarSwitchATM155		1.3.6.1.4.1.164.6.1.12.1.3
OBJECT IDENTIFIER

radAtmCsuDsu		1.3.6.1.4.1.164.6.1.12.2
OBJECT IDENTIFIER

radAmcdE1		1.3.6.1.4.1.164.6.1.12.2.1
OBJECT IDENTIFIER

radAmcdT1		1.3.6.1.4.1.164.6.1.12.2.2
OBJECT IDENTIFIER

radAce20E		1.3.6.1.4.1.164.6.1.12.2.3
OBJECT IDENTIFIER

radAce20T		1.3.6.1.4.1.164.6.1.12.2.4
OBJECT IDENTIFIER

radAce2005		1.3.6.1.4.1.164.6.1.12.2.5
OBJECT IDENTIFIER

radAce2002		1.3.6.1.4.1.164.6.1.12.2.6
OBJECT IDENTIFIER

radAce2002E		1.3.6.1.4.1.164.6.1.12.2.7
OBJECT IDENTIFIER

radAce2E		1.3.6.1.4.1.164.6.1.12.2.8
OBJECT IDENTIFIER

radAce2T		1.3.6.1.4.1.164.6.1.12.2.9
OBJECT IDENTIFIER

radMlAtmE1		1.3.6.1.4.1.164.6.1.12.2.10
OBJECT IDENTIFIER

radMlAtmT1		1.3.6.1.4.1.164.6.1.12.2.11
OBJECT IDENTIFIER

radAmc102		1.3.6.1.4.1.164.6.1.12.2.12
OBJECT IDENTIFIER

radAmc102c		1.3.6.1.4.1.164.6.1.12.2.13
OBJECT IDENTIFIER

radAce202		1.3.6.1.4.1.164.6.1.12.2.14
OBJECT IDENTIFIER

radAce		1.3.6.1.4.1.164.6.1.12.3
OBJECT IDENTIFIER

radAce101		1.3.6.1.4.1.164.6.1.12.3.1
OBJECT IDENTIFIER

radAce102		1.3.6.1.4.1.164.6.1.12.3.2
OBJECT IDENTIFIER

radAce50		1.3.6.1.4.1.164.6.1.12.3.3
OBJECT IDENTIFIER

radAce52		1.3.6.1.4.1.164.6.1.12.3.4
OBJECT IDENTIFIER

radAce52L		1.3.6.1.4.1.164.6.1.12.3.5
OBJECT IDENTIFIER

radAce201		1.3.6.1.4.1.164.6.1.12.3.7
OBJECT IDENTIFIER

radAce3200		1.3.6.1.4.1.164.6.1.12.3.8
OBJECT IDENTIFIER

radAce3100		1.3.6.1.4.1.164.6.1.12.3.9
OBJECT IDENTIFIER

radAce3400		1.3.6.1.4.1.164.6.1.12.3.10
OBJECT IDENTIFIER

radAce3402		1.3.6.1.4.1.164.6.1.12.3.11
OBJECT IDENTIFIER

radAce3100PSN		1.3.6.1.4.1.164.6.1.12.3.12
OBJECT IDENTIFIER

radAce3200PSN		1.3.6.1.4.1.164.6.1.12.3.13
OBJECT IDENTIFIER

radAce3400PSN		1.3.6.1.4.1.164.6.1.12.3.14
OBJECT IDENTIFIER

radAce3402PSN		1.3.6.1.4.1.164.6.1.12.3.15
OBJECT IDENTIFIER

radAce3600		1.3.6.1.4.1.164.6.1.12.3.16
OBJECT IDENTIFIER

radAce3205		1.3.6.1.4.1.164.6.1.12.3.17
OBJECT IDENTIFIER

radAce3105		1.3.6.1.4.1.164.6.1.12.3.18
OBJECT IDENTIFIER

radSysLA		1.3.6.1.4.1.164.6.1.13
OBJECT IDENTIFIER

radLA140		1.3.6.1.4.1.164.6.1.13.1
OBJECT IDENTIFIER

radLA110		1.3.6.1.4.1.164.6.1.13.2
OBJECT IDENTIFIER

radLA104		1.3.6.1.4.1.164.6.1.13.3
OBJECT IDENTIFIER

radLA130		1.3.6.1.4.1.164.6.1.13.4
OBJECT IDENTIFIER

radLA210		1.3.6.1.4.1.164.6.1.13.5
OBJECT IDENTIFIER

radSysTerminal		1.3.6.1.4.1.164.6.1.100
OBJECT IDENTIFIER

agnt		1.3.6.1.4.1.164.6.2
OBJECT IDENTIFIER

agnHwVersion		1.3.6.1.4.1.164.6.2.1
ASCII string for description and display of the agent hardware version, as it is known by the agent software.The user can update the version upon request when he changes components in the agent's module
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

agnTrapMask		1.3.6.1.4.1.164.6.2.2
The value of this attribute determines the type of traps the agent should mask and not send to the management console. The value is differently determined for different products. There are mainly two methods: - an integer number, specifying the traps' severity. - a sum of 2**n, where n is a bit assigned to a certain masked trap group. User should consult the product specification, to find out the method employed.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

agnTrapValue		1.3.6.1.4.1.164.6.2.3
The value of the trap decoded in internal RAD format. Full description is given in the Trap definition file
Status: deprecated	Access: read-only
OBJECT-TYPE
	OCTET STRING

agnChangeCnt		1.3.6.1.4.1.164.6.2.4
The number of changes in system configuration that were reported to the manager since last cold start
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

agnSpecific		1.3.6.1.4.1.164.6.2.5
Object identifier of entity containing additional information regarding this instance.
Status: current	Access: read-only
OBJECT-TYPE
	OBJECT IDENTIFIER

agnConfigMsg		1.3.6.1.4.1.164.6.2.6
Full configuration message coded in internal RAD application format. This entry describes agent's configuration. For MP-2200 R3, this object describes agent's support of the V5.1 feature: 1 octet ; bit 0 (LSB). '1' - V5.1 feature is supported '0' - V5.1 feature is not supported.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

mngTrapIpTable		1.3.6.1.4.1.164.6.2.7
This table indicates the destination address of the traps. Internally it will be limited to ten addresses.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MngEntry

mngEntry		1.3.6.1.4.1.164.6.2.7.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	MngEntry

mngID		1.3.6.1.4.1.164.6.2.7.1.1
This value indicates an index of a specific IP address
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

mngIP		1.3.6.1.4.1.164.6.2.7.1.2
This value indicates the destination address of the traps. IP 0.0.0.0 removes the entry.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

mngIPMask		1.3.6.1.4.1.164.6.2.7.1.3
This value indicates the mask of the destination addresses of the traps.
Status: deprecated	Access: read-write
OBJECT-TYPE
	IpAddress

mngTrapMask		1.3.6.1.4.1.164.6.2.7.1.4
The value of this attribute determines the type of traps the agent should mask and not send to this NMS. The value is differently determined for different products. There are mainly two methods: - an integer number, specifying the traps' severity. - a sum of 2**n, where n is a bit assigned to a certain masked trap group. User should consult the product specification, to find out the method employed.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

mngAlarmTrapMask		1.3.6.1.4.1.164.6.2.7.1.5
The value of this object determines the alarm traps that the agent should mask (not send to this manager). The value is an Octet String, where each bit is assigned to a certain trap. If the bit = 1, the trap will be masked. If the bit = 0, the trap will not be masked. For more details on the specific alarm traps masked, see product specification.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

mngSnmpTrapUdpPort		1.3.6.1.4.1.164.6.2.7.1.6
This variable enables to set the UDP port (socket) used for SNMP traps.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

agnIndication		1.3.6.1.4.1.164.6.2.8
Attribute describing the state of the entity the agent is responsible for. In case of a modular entity, the value of this attribute will be according to the component which is in the worst state. The order of severity (from top to bottom) is: critical-> major (or faulty)-> minor-> event-> warning-> normal (off).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	faulty(1), warning(2), normal(3), minor(4), major(5), event(6), critical(7)

agnMonitorModeCmd		1.3.6.1.4.1.164.6.2.9
Setting this attribute to ON, will enforce the agent to change its mode of operation to Monitor Mode
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), off(2), on(3)

agnLed		1.3.6.1.4.1.164.6.2.10
This entry specifies the LEDs status of the agent module . Each led will be represented by 4 bits where the first 2 bits (left) will specify the status : (00=NA, 01=OFF, 10=ON, 11=BLINK), and the next two bits (right) will specify the color : (00=GREEN, 01=RED, 10=YELLOW, 11=GRAY)
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

trapTable		1.3.6.1.4.1.164.6.2.11
This table may include the last few traps generated by the agent, for future retrieval. The table has a limited capacity. If traps are not retrieved in proper time, they will be over-written by new traps. For other devices, it can include generic variables that will be attached to traps as 'accessible-for-notify'.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TrapEntry

trapEntry		1.3.6.1.4.1.164.6.2.11.1
An entry in trapTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	TrapEntry

trapID		1.3.6.1.4.1.164.6.2.11.1.1
This object indicates an index of a specific trap. Can be used also for any trap, while trapVal is used as 'accessible-for-notify' or trapNumeric is used.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

trapVal		1.3.6.1.4.1.164.6.2.11.1.2
This object is the actual ASCII description of the trap. It can be used also as attached variable of traps, in order to detail in explicit ASCII text, data of the trap. In this case, it is used as 'accessible-for-notify'.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

trapTimeSinceOccurrence		1.3.6.1.4.1.164.6.2.11.1.3
This object indicates the amount of time passed since the occurrence of the event that triggered this trap.
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

trapNumeric		1.3.6.1.4.1.164.6.2.11.1.4
This object is a numeric general parameter, that can be attached to any trap. Values can be positive or negative.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

fileTransfer		1.3.6.1.4.1.164.6.2.12
OBJECT IDENTIFIER

fileServerIP		1.3.6.1.4.1.164.6.2.12.1
The IP address of the server from which the file is loaded
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

fileName		1.3.6.1.4.1.164.6.2.12.2
The name of the file to be loaded. For protection, read returns NULL.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

fileTransCmd		1.3.6.1.4.1.164.6.2.12.3
The command to be executed on fileName at fileServerIP.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	swDwnLoad(1), configDwnLoad(2), configUpLoad(3), coProcDwnLoad(4), stateUpLoad(5), dwnLoadUserFile(6), upLoadUserFile(7), swDwnLoadAndReset(8), swUpLoad(9), swDwnLoad2BkupStorage(10), bootDwnLoad(11), bootUpLoad(12), swUpLoadFromBkupStorage(13), licenseDwnLoad(14), configDwnLoadToDefaultFile(15), noOp(255)

tftpRetryTimeOut		1.3.6.1.4.1.164.6.2.12.4
General Retransmission time-out value (seconds)
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

tftpTotalTimeOut		1.3.6.1.4.1.164.6.2.12.5
Total Retransmission time-out value (seconds)
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

tftpStatus		1.3.6.1.4.1.164.6.2.12.6
Status of tftp session. When a session ended with success, the tftpStatus should be endedOk(6). Before restarting a tftp session, the NMS should set the tftpStatus to noOp(2). That's the reason of MAX-ACCESS read-write to this field.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noOp(2), connecting(3), transferringData(4), endedTimeOut(5), endedOk(6), error(7)

tftpError		1.3.6.1.4.1.164.6.2.12.7
The MSB represents the standard error code. The LSB represents the private error code. 0x0000 is No Error 0x0100 is File Not Found 0x0200 is Access violation 0x0300 is Disk full or allocation exceeded 0x0400 is Illegal TFTP operation 0x0500 is Unknown transfer ID 0x0600 is File already exists 0x0700 is No such user 0x0001 is Server Overflow 0x0002 is No empty UDP port 0x0003 is No empty connection 0x0004 is Illegal File Mode 0x0007 is Illegal PDU size 0x0008 is TFTP Server does not exist 0x0009 is Incorrect File 0x000A is Wrong License format 0x000B is License ID already used
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(2)

fileTransferToSubSystems		1.3.6.1.4.1.164.6.2.12.8
This object represents the sub-systems the fileTransCmd refers to. It should be used when a system is divided to sub-systems and each sub-system (or part of them) can have a different SW/Configuration. Each bit of this object will represent one of the sub-systems. Bit='1' - APPLY to respective sub-system Bit='0' - DO NOT APPLY to respective sub-system For the meaning of each bit, see product's specification. User will select the sub-systems envolved by filling-in the bits that represent these sub-systems. In this case, the file represented by 'fileName' will include several parts, each representing one of the sub-systems. The agent will refer only to the part/s indicated by this object. 0 Octet Strings = not applicable DEFVAL = 0h for the products that support this object.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

fileNameWithinProduct		1.3.6.1.4.1.164.6.2.12.9
The file name used by the product within the product file system.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

intSwdlTable		1.3.6.1.4.1.164.6.2.12.10
This parameters table is for internal Software down load. It also includes data about all files contained in the Object from which down-load is performed.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IntSwdlEntry

intSwdlEntry		1.3.6.1.4.1.164.6.2.12.10.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	IntSwdlEntry

intSwdlObjIdx		1.3.6.1.4.1.164.6.2.12.10.1.1
The index of the object from which down-load is performed.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

intSwdlFileIdx		1.3.6.1.4.1.164.6.2.12.10.1.2
The index of the files included in intSwdlObjIdx. One of these files can be selected to be internally downloaded.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

intSwdlFileName		1.3.6.1.4.1.164.6.2.12.10.1.3
The name of the file.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

intSwdlFileSwVer		1.3.6.1.4.1.164.6.2.12.10.1.4
The software version of the file.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

intSwdlSwDate		1.3.6.1.4.1.164.6.2.12.10.1.5
The software version date of the file.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

intSwdlSize		1.3.6.1.4.1.164.6.2.12.10.1.6
The size of the file.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

intSwdlCmd		1.3.6.1.4.1.164.6.2.12.10.1.7
The command to down-load a SW file to an object. The Agent will change the value of this MIB object to off(2) automatically, after accepting the command.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), off(2), on(3)

intSwdlToSubSystem		1.3.6.1.4.1.164.6.2.12.10.1.8
This object defines the subsystem for download. Bit='1'- APPLY to respective sub system. Bit='0'- DO NOT APPLY to respective sub system. For more details see product specification. For every octet bit0=LSB, bit7=MSB
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

intSwdlCardType		1.3.6.1.4.1.164.6.2.12.10.1.9
This object defines the Card type that this file is relevant for.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), gstm1(220), goc3(221), gstm1D(222), goc3D(223), serverE1(270), serverT1(271), serverE1Pw(272), serverT1Pw(273), gigabitEth(280), gigabitEth2(281), eth2(282), gigabitEth8(283), eth8(284), channelizedT3Pw1(290), cesT128(300), cesE128(301), cesT1Pw28(302), cesE1Pw28(303), vmxE1VeDe(310), vmxE1VeDi(311), vmxE1ViDe(312), vmxE1ViDi(313), vmxT1VeDe(314), vmxT1VeDi(315), vmxT1ViDe(316), vmxT1ViDi(317), vc12E1UeNe(318), vc12E1UeNi(319), vc12E1UiNe(320), vc12E1UiNi(321), vc12T1UeNe(322), vc12T1UeNi(323), vc12T1UiNe(324), vc12T1UiNi(325), vca16E1UeNe(326), vca16E1UeNi(327), vca16E1UiNe(328), vca16E1UiNi(329), vca16T1UeNe(330), vca16T1UeNi(331), vca16T1UiNe(332), vca16T1UiNi(333), vca12E1UeNe(334), vca12E1UeNi(335), vca12E1UiNe(336), vca12E1UiNi(337), vca12T1UeNe(338), vca12T1UeNi(339), vca12T1UiNe(340), vca12T1UiNi(341), vmg16E1Ue(342), vmg16E1Ui(343), vmg16T1Ue(344), vmg16T1Ui(345), vmg12E1Ue(346), vmg12E1Ui(347), vmg12T1Ue(348), vmg12T1Ui(349)

intSwdlFlashIdx		1.3.6.1.4.1.164.6.2.12.10.1.10
The index of the flash memory this file is stored in (1 or 2) (Example: 1= The file is stored in flash No.1). ASMi52 file will always be stored in Flash No.2 (intSwdlFlashIdx=2).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

swdlStatusTable		1.3.6.1.4.1.164.6.2.12.11
This parameters table is for software download status. It also includes data about the files down-loaded or attempted to be down-loaded.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwdlStatusEntry

swdlStatusEntry		1.3.6.1.4.1.164.6.2.12.11.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwdlStatusEntry

swdlStatusTypeIdx		1.3.6.1.4.1.164.6.2.12.11.1.1
The index of the down-load type (e.g. external (1) or internal (2)).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

swdlStatusIdx		1.3.6.1.4.1.164.6.2.12.11.1.2
The index of the status rows.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

swdlStatusFileName		1.3.6.1.4.1.164.6.2.12.11.1.3
The name of the file.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

swdlStatusSlot		1.3.6.1.4.1.164.6.2.12.11.1.4
The slot of the updated (or attempted to be updated) object.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

swdlStatusSubSystem		1.3.6.1.4.1.164.6.2.12.11.1.5
The subsystem that updated (or attempted to be updated).
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

swdlStatusStatus		1.3.6.1.4.1.164.6.2.12.11.1.6
The status of the down load process. Value: Fail (2), OK (3), InProcess (4).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

swdlStatusTime		1.3.6.1.4.1.164.6.2.12.11.1.7
This MIB parameter indicates the time SW download was finished. The format shuld be YYYY-MM-DD, hh:mm:ss
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

clearDwldStatusLog		1.3.6.1.4.1.164.6.2.12.12
This object clears the status log. Value: off(2), external(3), internal(4) The Agent will change the value of this MIB object to off(2) automatically, after accepting the command .
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

autoFileTransfer		1.3.6.1.4.1.164.6.2.12.13
OBJECT IDENTIFIER

autoFileTransferTable		1.3.6.1.4.1.164.6.2.12.13.1
Scheduling configuration table for Agent initiated file transfer.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AutoFileTransferEntry

autoFileTransferEntry		1.3.6.1.4.1.164.6.2.12.13.1.1
An entry in the table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AutoFileTransferEntry

autoFileTransferType		1.3.6.1.4.1.164.6.2.12.13.1.1.1
This object defines the type of file to be transferred by agent.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	alarmsBuffer(1)

autoFileTransferServerIp		1.3.6.1.4.1.164.6.2.12.13.1.1.2
This object defines the IP Address of the server to which the file is uploaded.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

autoFileTransferFileName		1.3.6.1.4.1.164.6.2.12.13.1.1.3
This object defines the name of the file to be uploaded.
Status: current	Access: read-write
OBJECT-TYPE
	SnmpAdminString

autoFileTransferScheduling		1.3.6.1.4.1.164.6.2.12.13.1.1.4
This object defines schedule for TFTP Automatic session(s) initiated by Agent, according to the value selected: now - initiate immediate single session. recurrence- initiate single session 'every M time units'. or 'every N occurrences' or upon both, (earliest event). Time reccurence period (M) is defined by fileTransferTimeRecurrence. Occurrence reccurence (N) is defined by fileTransferOccurrenceRecurrence. Zero value means that the object is not relevant (not taken into account for the recurrence). It is invalid that both will have zero values in our case (recurrence). When both are non zero, file is transferred upon earliest event
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), now(2), recurrence(3)

autoFileTransferTimeRecurrence		1.3.6.1.4.1.164.6.2.12.13.1.1.5
This object defines time reccurence interval, e.g. M can be 'every M days', 'every M hours' etc. Zero is used to indicate there's no time reccurence (0= notApplicable). This object is taken into account only if autoFileTransferScheduling = recurrence For LA-110 time units are days.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

autoFileTransferOccurrenceRecurrence		1.3.6.1.4.1.164.6.2.12.13.1.1.6
This object defines Occurrence reccurence interval, e.g N can be in 'every N alarms', 'every N log entries' etc. zero is used to indicate There's no Event Reccurence. (0= notApplicable) This object is taken into account only if autoFileTransferScheduling = recurrence Occurence Type (Alarms, etc.) is according to autoFileTransferType.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

fileTransferServerPort		1.3.6.1.4.1.164.6.2.12.14
Server Port number used for File Transfer. Applicable for SFTP. Valid values: 0..65535.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

fileTransferProtocol		1.3.6.1.4.1.164.6.2.12.15
File Transfer protocol used.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	tftp(1), sftp(2)

systemReset		1.3.6.1.4.1.164.6.2.13
Reset action to be performed on the system. - resetMapping - reset SDH/SONET mapping to default for all SDH/SONET links. - resetStandby(6) - can be used only by devices with redundancy on MAIN/CL.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3), resetConfig(4), resetMapping(5), resetStandby(6)

systemTiming		1.3.6.1.4.1.164.6.2.14
OBJECT IDENTIFIER

systemDate		1.3.6.1.4.1.164.6.2.14.1
System date.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

systemTime		1.3.6.1.4.1.164.6.2.14.2
System time.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

systemTimeElapsed		1.3.6.1.4.1.164.6.2.14.3
The number of seconds that have elapsed since the beginning of the current error-measurement period. Same for all ports of the device.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..899

systemNtp		1.3.6.1.4.1.164.6.2.14.4
OBJECT IDENTIFIER

systemNtpMode		1.3.6.1.4.1.164.6.2.14.4.1
This variable represents the NTP Mode.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(2), broadcastClient(3), unicastClient(4)

systemNtpGmt		1.3.6.1.4.1.164.6.2.14.4.2
This variable represents the NTP GMT (Greenwich Mean Time), Possible values range is -12..12. For new devices/versions this variable will be in minutes.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

systemNtpServerAddressType		1.3.6.1.4.1.164.6.2.14.4.3
This variable represents the NTP Server Address Type.
Status: current	Access: read-write
OBJECT-TYPE
	InetAddressType

systemNtpServerAddress		1.3.6.1.4.1.164.6.2.14.4.4
This variable represents the NTP Server Address.
Status: current	Access: read-write
OBJECT-TYPE
	InetAddress

systemNtpUpdateInterval		1.3.6.1.4.1.164.6.2.14.4.5
This variable represents the NTP Update Interval, measured in seconds.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

systemNtpCmd		1.3.6.1.4.1.164.6.2.14.4.6
This variable represents NTP possible commands. After the Agent accepts a command, it will automatically change the value to off(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), sendUpdateRequest(3)

schedXTable		1.3.6.1.4.1.164.6.2.14.5
An Augment to the Schedule table (schedTable in DISMAN-SCHEDULE-MIB; RFC-3231).
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SchedXEntry

schedXEntry		1.3.6.1.4.1.164.6.2.14.5.1
An entry in the table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SchedXEntry

schedYear		1.3.6.1.4.1.164.6.2.14.5.1.1
The year during which the scheduled action should take place.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

schedWeekInMonth		1.3.6.1.4.1.164.6.2.14.5.1.2
The week in month (schedMonth) during which the scheduled action should take place.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	first(1), second(2), third(3), fourth(4), last(5)

schedParam		1.3.6.1.4.1.164.6.2.14.5.1.3
A Parameter that might be used whenever the scheduled action takes place. For summer-time schedule - This variable represents the time offset (in minutes), meaning: the number of minutes that should be added for summer-time.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

systemPort		1.3.6.1.4.1.164.6.2.15
OBJECT IDENTIFIER

physicalConnectorTable		1.3.6.1.4.1.164.6.2.15.1
This table includes the connector type of ports or interfaces.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PhysicalConnectorEntry

physicalConnectorEntry		1.3.6.1.4.1.164.6.2.15.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PhysicalConnectorEntry

portIdx		1.3.6.1.4.1.164.6.2.15.1.1.1
This object is an index of the specific port or interface. For a port, the index will be as agreed between agent and application. For an interface, ifIndex may be used.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

physicalConnector		1.3.6.1.4.1.164.6.2.15.1.1.2
The connector of the port/interface. other - none of the specified connectors none - no connector.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), v35(2), rs530(3), x21(4), bnc(5), utp(6), aui(7), rs422(8), crossUtp(9), rj45(10), v24(11), g703(12), termBlock3AndRj45(13), terminalBlock3(14), terminalBlock5(15), terminalBlock7(16), db25(17), db15(18), rj45ethernet(19), termBlock5AndRj45(20), db9(21), g703E1(22), g703E1-LTU(23), sc(24), st(25), stl(26), fc(27), tb5w(28), termBlock6AndRj45(29), ethBnc(30), scsi26(31), eth4381(32), twoBnc(33), scsi50(34), twoMiniBnc(35), sf1(36), terminalBlock4(37), sf2(38), db25Balanced(39), v36(40), block4W(41), iripRj45(42), irEthQRj45(43), iripBnc(44), rs530WA(45), v35WA(46), irEthQBnc(47), v35Db25(48), rj11(49), mtrj(50), lc(51), terminalBlock2(52), irEth10s100(53), scsi68(54), sf3(55), fcLH(56), telco50(57), telco64(58), irEthQN(59), terminalBlock6(60), scLH(61), stLH(62), lcLH(63), sfpIn(64), sfpOut(65), db44(66), db62(67), v24Db9(68), scsi40(69), sf1NineRow(70), sf2NineRow(71), sf3NineRow(72), smartSerial26(73), miniUsb5(74), db26(75), none(255)

portOptWaveLength		1.3.6.1.4.1.164.6.2.15.1.1.3
Wave Length of an Optical interface/port in [nm] and specification if Laser or not. notApplicable - for non-optical ports.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), nm850(2), nm1310(3), nm1310Laser(4), nm1550Laser(5), nm1470Laser(6), nm1490Laser(7), nm1510Laser(8), nm1530Laser(9), nm1570Laser(10), nm1590Laser(11), nm1610Laser(12)

portOptMode		1.3.6.1.4.1.164.6.2.15.1.1.4
Laser Mode of an Optical Laser interface/port. notApplicable - for non-Laser ports.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), singleMode(2), multiMode(3)

portBalance		1.3.6.1.4.1.164.6.2.15.1.1.5
This object is according to the port Impedance. For T1 - always balanced. For E1 - there are different impedance values for balanced and unbalanced.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), unbalanced(2), balanced(3)

portDdmSupport		1.3.6.1.4.1.164.6.2.15.1.1.6
SFP (Small Form Pluggable) port -support Digital Diagnostics Monitoring.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), no(2), yes(3)

portMfgName		1.3.6.1.4.1.164.6.2.15.1.1.7
(SFP) Port Manufacturer name (Maximum - 16 characters).
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString

portTypicalMaxRange		1.3.6.1.4.1.164.6.2.15.1.1.8
Maximum range supported by SFP port, in meter units.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

physicalConnectorString		1.3.6.1.4.1.164.6.2.15.1.1.9
(SFP) connector type. It can be Vendor Specific (unknown in advance). Being a string, the object is not affected by any future new connectors. This object will usually not be used for drawing the connector.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString

portVendorPartNo		1.3.6.1.4.1.164.6.2.15.1.1.10
SFP Vendor Part Number. Being a string, the object is not affected by any future new SFPs.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString

prtSupervisory		1.3.6.1.4.1.164.6.2.15.2
OBJECT IDENTIFIER

prtSpTable		1.3.6.1.4.1.164.6.2.15.2.1
A table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtSpEntry

prtSpEntry		1.3.6.1.4.1.164.6.2.15.2.1.1
Supervisory port parameter table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtSpEntry

prtSupervisoryIndex		1.3.6.1.4.1.164.6.2.15.2.1.1.1
The SP port index. For some products, having modules (cards): The LS byte of the integer is the port index 1..255. The MS byte is different than 0 only if the port belongs to a module. In that case it is the module number. For other products' index see their specification.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtSupervisoryRate		1.3.6.1.4.1.164.6.2.15.2.1.1.2
This attribute indicates the operation rate (speed) of the port. auto - automatic rate selection, by the agent.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	auto(1), s300bps(2), s1200bps(3), s2400bps(4), s4800bps(5), s9600bps(6), s19200bps(7), s38400bps(8), s57600bps(9), s115200bps(10)

prtSupervisoryDataBits		1.3.6.1.4.1.164.6.2.15.2.1.1.3
This attribute indicates the number of data bits in an async frame
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	dataBits7(1), dataBits8(2)

prtSupervisoryParity		1.3.6.1.4.1.164.6.2.15.2.1.1.4
This attribute indicates the parity mode in an async frame
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), odd(2), even(3)

prtSupervisoryStopBits		1.3.6.1.4.1.164.6.2.15.2.1.1.5
This attribute indicates the parity mode in an async frame.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), stopBits1(2), stopBits1dot5(3), stopBits2(4)

prtSupervisoryUsage		1.3.6.1.4.1.164.6.2.15.2.1.1.6
This attribute indicates the usage of the SP port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unknown(1), noUse(2), terminal(3), nmsSlip(4), nmsPpp(5), muxSlip(6), muxPpp(7), dialOut(8)

prtSupervisoryInterface		1.3.6.1.4.1.164.6.2.15.2.1.1.7
This attribute indicates the supervisory port interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), dce(2), dte(3)

prtSupervisoryCTS		1.3.6.1.4.1.164.6.2.15.2.1.1.8
CTS line state.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), on(2), rts(3), dteWait(4), dteIgnore(5)

prtSupervisoryDcdDelay		1.3.6.1.4.1.164.6.2.15.2.1.1.9
DCD delay in msec.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), d0(2), d10(3), d50(4), d100(5), d200(6), d300(7)

prtSupervisoryDSR		1.3.6.1.4.1.164.6.2.15.2.1.1.10
DSR line state.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), on(2), dtr(3)

prtSupervisoryRoutProtocol		1.3.6.1.4.1.164.6.2.15.2.1.1.11
This attribute indicates the routing protocol of the port. notApplicable - for DP.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), none(2), proprietary(3), rip2(4)

prtPerformance		1.3.6.1.4.1.164.6.2.15.3
OBJECT IDENTIFIER

prtPerfTable		1.3.6.1.4.1.164.6.2.15.3.1
This table includes G.826 ports or interfaces.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtPerfEntry

prtPerfEntry		1.3.6.1.4.1.164.6.2.15.3.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtPerfEntry

prtPerfIdx		1.3.6.1.4.1.164.6.2.15.3.1.1.1
This object is an index of the specific port or interface. For a port, the index will be as agreed between agent and application. For an interface, ifIndex may be used.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtPerfPeriodRef		1.3.6.1.4.1.164.6.2.15.3.1.1.2
This object is an index that specifies which period of time, the next 5 objects refer to. currentPeriod - the period since last prtPerfSaveAndResetCmd received or since Start-up (if no prtPerfSaveAndResetCmd was received since Start-up) until now. lastPeriod - the period between last two commands of prtPerfSaveAndResetCmd. - If only one command occured since Start-up: the period between Start-up and last command. - If no command occured since Start-up: this period will not actually exist. In this case, he following 5 objects will be 0.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	currentPeriod(1), lastPeriod(2)

prtPerfElapsedTime		1.3.6.1.4.1.164.6.2.15.3.1.1.3
Elapsed Time in seconds. - for prtPerfPeriodRef=currentPeriod: The period since last prtPerfSaveAndResetCmd received or since Start-up (if no prtPerfSaveAndResetCmd was received since Start-up) until now. - for prtPerfPeriodRef=lastPeriod: The value of prtPerfElapsedTime when last prtPerfSaveAndResetCmd was received.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtPerfUAS		1.3.6.1.4.1.164.6.2.15.3.1.1.4
Number of Unavailable Seconds for the reference period (prtPerfPeriodRef).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtPerfES		1.3.6.1.4.1.164.6.2.15.3.1.1.5
Number of Errored Seconds for the reference period (prtPerfPeriodRef).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtPerfSES		1.3.6.1.4.1.164.6.2.15.3.1.1.6
Number of Severely Errored Seconds for the reference period (prtPerfPeriodRef).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtPerfBBE		1.3.6.1.4.1.164.6.2.15.3.1.1.7
Number of Background Block (or Frame) Errors for the reference period (prtPerfPeriodRef).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtPerfBlocksPerSec		1.3.6.1.4.1.164.6.2.15.3.1.1.8
Blocks per second (or frames per second) of the port/interface indicated by portIdx. This object is constant for a certain port/interface. It is not affected by the prtPerfPeriodRef index.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtPerfTimeTag		1.3.6.1.4.1.164.6.2.15.3.1.1.9
Time Tag of Last Period: sysUpTime when last prtPerfSaveAndResetCmd was executed. This object is applicable only for prtPerfPeriodRef=lastPeriod. For prtPerfPeriodRef=currentPeriod, the value will always be 0.
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

prtPerfSaveAndResetCmd		1.3.6.1.4.1.164.6.2.15.3.1.1.10
A command per port/interface, to Save data of Current Period in Last Period data-set and start a new counting period for Current Period. This object is applicable only for prtPerfPeriodRef=currentPeriod. Setting this object to on(3) for prtPerfPeriodRef=last, will cause the agent to return: Bad Value response. When setting validly this object to on(3), agent will perform the required command and will reset automatically the value of this object to off(2). Setting this object to off(2), will do nothing.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

prtTest		1.3.6.1.4.1.164.6.2.15.4
OBJECT IDENTIFIER

prtTestTable		1.3.6.1.4.1.164.6.2.15.4.1
This table includes test data for ports or interfaces.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtTestEntry

prtTestEntry		1.3.6.1.4.1.164.6.2.15.4.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtTestEntry

prtTestIdx		1.3.6.1.4.1.164.6.2.15.4.1.1.1
This object is an index of the specific port or interface. For a port, the index will be as agreed between agent and application. For an interface, ifIndex may be used.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtTestCmdAndStatus		1.3.6.1.4.1.164.6.2.15.4.1.1.2
Setting this object to a value as detailed further on (except 0) will initiate a test on the specific port. The test/s requested will be set according to the respective bit. The value of this object will be a sum of (2**n), where n is the Bit: TEST BIT VALUE ----------- --- ------ reserved 0 1 PayloadLoop=RLB 1 (=Remote Loopback) 2 LineLoop=DIG 2 (=Digital) 4 OtherLoop 3 8 InwardLoop=LLB 4 (=Local Loopback) 16 BERT 5 32 LC 6 64 ToneInjection 7 128 Inband 8 256 BERT Remote (or E1/T1 RLB) 9 512 Downstream-AIS (or E1/T1 LLB) 10 1024 Upstream-AIS 11 2048 Rem-Loop-on-Rem-Unit 12 4096 MacSwapLoop 13 8192 OamETHLoopback 14 16384 OamETHLinkTrace 15 32768 e.g : If the requested value is 20 -> 010100 -> Bits 2 & 4 are set -> the requested tests are : LineLoopback=DIG InwardLoopback=LLB Not all tests combinations are valid. For valid test combination, see each product's specification. For LRS52, only single test is allowed simultaneously The terminology and order of the first tests (except BERT) is according to the one used for Test Status of DS1 and DS3 standards. The notations : RLB, LLB, DIG are the most used in RAD's products, but they can be different. For exact definition see product's spec. Setting this object to stop (value=0 ; all bits are 0), will stop all the user requested tests running on the selected port. When no test is running on the port, the Get value (test status) will be 0. PayloadLoop=RLB The received signal at this interface is looped through the device. Typically the received signal is looped back for retransmission after it has passed through the device's framing function. LineLoop=DIG The received signal at this interface does not go through the device (minimum penetration) but is looped back out. OtherLoop Loopbacks that are not defined here. InwardLoop=LLB The sent signal at this interface is looped back through the device. LC This loop is applicable only for HSSI interface, towards the router . ToneInjection This loop is applicable for analog voice (like FXS). Downstream-AIS E1 AIS signal (all ones) is transmitted in the relevant channel toward the STM-1 line. Upstream-AIS E1 AIS signal (all ones) is generated in the relevant channel toward the local received tributary channel output Rem-Loop-on-Rem-Unit Request from far end device to activate remote loopback towards near-end device MacSwapLoop This loop is applicable for ethernet port. Loop is implemented by swapping the MAC addresses of the incoming message. OamETHLoopback Ethernet Loopback is used to verify connectivity of a MEP with a MIP or peer MEP(s) (ITU-T Y.1731, Clause 7.2). OamETHLinkTrace Ethernet Link Trace is an on-demand OAM function which can be used for the two following purposes: - Adjacent Relation Retrieval - Fault Localization (ITU-T Y.1731, Clause 7.3).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtBertCounter		1.3.6.1.4.1.164.6.2.15.4.1.1.3
This object indicates the number of BERT errors encountered during the BERT operation. It is valid only when BERT (Bit Error Rate Test) is active on the specific port. The Counter starts from zero (0) anytime BERT is initiated.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtTestInitiator		1.3.6.1.4.1.164.6.2.15.4.1.1.4
This object indicates who initiated this port's test/s.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), user(2), remoteUnit(3), dteRouter(4)

prtTestTimeout		1.3.6.1.4.1.164.6.2.15.4.1.1.5
This object is applicable only when a single test is running. It indicates the test activation timeout in minutes. For RICi-E1T1, RICi-E3T3 the measurement unit is in seconds. When the timeout expires, the test is stopped. Value of 0 indicates test may run Forever
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..4095

prtTestVctRxResult		1.3.6.1.4.1.164.6.2.15.4.1.1.6
This object indicates the result of the Vct on the cable connected to the RX connector.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), fail(2), normal(3), open(4), short(5), shortToCrossPair(6), coupleWithCrossPair(7)

prtTestVctTxResult		1.3.6.1.4.1.164.6.2.15.4.1.1.7
This object indicates the result of the Vct on the cable connected to the TX connector.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), fail(2), normal(3), open(4), short(5), shortToCrossPair(6), coupleWithCrossPair(7)

prtTestVctRxDistance		1.3.6.1.4.1.164.6.2.15.4.1.1.8
This object indicates the distance in Meters to the RX cable Open/ Short location discovered by the Vct. This parameter is applicable for Vct Result = Normal or Fail only, Else the value of this parameter will be equal to 0.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtTestVctTxDistance		1.3.6.1.4.1.164.6.2.15.4.1.1.9
This object indicates the distance in Meters to the TX cable Open/ Short location discovered by the Vct. This parameter is applicable for Vct Result = Normal or Fail only, Else the value of this parameter will be equal to 0.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtTestVctCmd		1.3.6.1.4.1.164.6.2.15.4.1.1.10
Vct command. on (3) = Start Vct on both cables connected to RX and TX connectors of this port. Agent will perform the required command and change automatically the value of this object to off(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

prtTestVctRxCrossPair		1.3.6.1.4.1.164.6.2.15.4.1.1.11
This object should be equal to the Index (prtTestIdx) of the Rx cross pair. This object is applicable only for Vct Result = shortToCrossPair or coupleWithCrossPair. This object was especially created for ETX-202. Currently not in use.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtTestVctTxCrossPair		1.3.6.1.4.1.164.6.2.15.4.1.1.12
This object should be equal to the Index (prtTestIdx) of the Tx cross pair. This object is applicable only for Vct Result = shortToCrossPair or coupleWithCrossPair.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtTestActivationDelay		1.3.6.1.4.1.164.6.2.15.4.1.1.13
This object is applicable only when a single test is running. It indicates test activation delay in seconds. A Value of 0 indicates that the test starts immediately.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

prtTestMacSwapLoopDataMode		1.3.6.1.4.1.164.6.2.15.4.1.1.14
This object defines which part of the data will be looped back.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	all(1), allExceptMng(2), specificVlan(3)

prtTestMacSwapLoopVlanId		1.3.6.1.4.1.164.6.2.15.4.1.1.15
This object specifies the VLAN ID for prtTestMacSwapLoopDataMode=specificVlan.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtTestMacSwapLoopDirection		1.3.6.1.4.1.164.6.2.15.4.1.1.16
This object defines the direction of the performed loopback. In ETX102 'local' corresponds to Ingress loop (either on User port or on Network port), and 'remote' corresponds to Egress loop (either on User port or on Network port).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	local(2), remote(3)

prtTestMacSwapLoopDestAddr		1.3.6.1.4.1.164.6.2.15.4.1.1.17
Configures the MAC address that will be sent in the Destination field of the packet in the outgoing direction.
Status: current	Access: read-write
OBJECT-TYPE
	MacAddress

prtTestMacSwapLoopSrcAddr		1.3.6.1.4.1.164.6.2.15.4.1.1.18
Configures the MAC address that will be sent in the Source field of the packet in the outgoing direction.
Status: current	Access: read-write
OBJECT-TYPE
	MacAddress

prtTestOamMinRoundTripDelay		1.3.6.1.4.1.164.6.2.15.4.1.1.19
The mininal value of round trip delay of loopback message for a session of OAM loopback.Units are msec.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

prtTestOamMaxRoundTripDelay		1.3.6.1.4.1.164.6.2.15.4.1.1.20
The maximum value of round trip delay of loopback message for a session of OAM loopback.Units are msec.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

prtTestOamAvgRoundTripDelay		1.3.6.1.4.1.164.6.2.15.4.1.1.21
The average round trip delay of loopback message for a session of OAM loopback.Units are msec.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

prtTestOamTxInterval		1.3.6.1.4.1.164.6.2.15.4.1.1.22
Indicates the interval between loopback sent messages.Units are msec.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

prtTestDestinationIpAddress		1.3.6.1.4.1.164.6.2.15.4.1.1.23
Indicates the destination IP Address in the transmitted messages that are looped back.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

prtTestTTL		1.3.6.1.4.1.164.6.2.15.4.1.1.24
Time-to-live.Number of hops the loopback message will go through the net before deciding to discard it.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

prtTestBwProfile		1.3.6.1.4.1.164.6.2.15.4.1.1.25
Indicates the BW profile (from bwProfileTable) that is assigned to the loopback test in order to limit the traffic that is looped back.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

prtParam		1.3.6.1.4.1.164.6.2.15.5
OBJECT IDENTIFIER

prtParamTable		1.3.6.1.4.1.164.6.2.15.5.1
This table includes general port parameters. The meaning is different for every product that supports it due to a general parameter - prtControlCnfg. For ACE2002: -This table is used as a mechanism to create the next interface index. The algorithm description: The NMS will send the agent the following get command: get(nextIfIndex.index), where index=interface on which the new index is dependent on. Upon this command the agent will generate and return the new index to the NMS. - This table is partially supported according to the interface type. Upon getNext function the irrelevant parameters will be skipped.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtParamEntry

prtParamEntry		1.3.6.1.4.1.164.6.2.15.5.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtParamEntry

prtParamIdx		1.3.6.1.4.1.164.6.2.15.5.1.1.1
This object is an index of the specific port or interface. For a port, the index will be as agreed between agent and application. For an interface, ifIndex may be used. For ACE2002: This parameter is the physical layer ifIndex of the slot on which the NMS requires the next interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtControlCnfg		1.3.6.1.4.1.164.6.2.15.5.1.1.2
This object may be used for port RW general parameter/s. For detailed meaning, see product's spec. Supported by: PRBi-E3/T3. For ACE2002: This parameter will include the value of the new index generated by agent. For Optimux-T3 and OP-155-1: This parameter will be used for Release Remote LLB Command: on=2= Set value only. Command to release LLB of Remote Unit. Agent will return automatically to 'off' value after performing the command. off=3=Get value only. For LA140 This parameter will be used as EchoCanceler per timeslot off = 2 Echo Canceler is disabled on = 3 Echo Canceler is enabled For FCD-155 This parameter will be used to select the port that is clock source for a PDH port, For E1/T1 PDH VC12/VT1.5 = 2 SDH/SONET = 3 For E3/T3 PDH VC3/DS3 = 2 SDH/SONET = 3 For ACE-52 This parameter will be used as Transmit Frame Type, i.e. which type of frame the corresponding bridge port will transmit: Untagged = 2 Tagged = 3 .
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtParamClkSrc		1.3.6.1.4.1.164.6.2.15.5.1.1.3
The source of Transmit Clock. 'loopTiming' or 'loopback' indicates that the recovered receive clock is used as the transmit clock. 'localTiming' or 'internal' indicates that a local clock source is used or when an external clock is attached to the box containing the interface. 'throughTiming' or 'external' indicates that recovered receive clock from another card or interface is used as the transmit clock. 'adaptive' indicates that the clock is recovered according to the received data flow rate. 'master' and 'fallback' values may be used RO to indicate active clock. 'station' - indicate clock received from station port is used as transmit clock.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	loopTiming(1), localTiming(2), throughTiming(3), adaptive(4), master(5), fallback(6), station(7), notApplicable(255)

prtParamPhantom		1.3.6.1.4.1.164.6.2.15.5.1.1.4
Power feeding to another device.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), enable(3)

prtParamResetStatsCmd		1.3.6.1.4.1.164.6.2.15.5.1.1.5
Reset statistics of the selected port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

prtParamLastResetStatsTime		1.3.6.1.4.1.164.6.2.15.5.1.1.6
The value of MIB II's sysUpTime object at the last time that prtParamResetStatsCmd was Set to on(3) for this port. If prtParamResetStatsCmd was never Set to on(3) since last re-initialization of the agent, then this object contains a zero value. This object enables calculating the running time of Statistics counters for this port, by: [sysUpTime-prtParamLastResetStatsTime]. For some devices other types of 'Reset' may affect this parameter
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

prtParamInterfaceType		1.3.6.1.4.1.164.6.2.15.5.1.1.7
The type of the port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), e1(2), t1(3), fr(4), hdlc(5), hdsl2(6), shdsl(7), adsl(8), adsl2(9), reAdsl2(10), mPair(11), efm(12), atmIma(13), ds1(14)

prtParamClearAlarm		1.3.6.1.4.1.164.6.2.15.5.1.1.8
Setting this attribute to ON, will enforce a clear operation on the Port Alarms. Upon completion, the value will automatically change to off(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

prtParamLeds		1.3.6.1.4.1.164.6.2.15.5.1.1.9
This entry specifies the LEDs status of the port. Each led is represented by 4 bits where the first 2 bits (left) specify the status : (00=NA, 01=OFF, 10=ON, 11=BLINK), and the next two bits (right) specify the color : (00=GREEN, 01=RED, 10=YELLOW, 11=GRAY). The order of the LEDS is from top to bottom, left to right: For each row starting from the top, the LEDS are returned from left to right.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

prtParamLineLength		1.3.6.1.4.1.164.6.2.15.5.1.1.10
Line Length of the line connected to this port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), long(2), normal(3), short(4)

prtParamUsage		1.3.6.1.4.1.164.6.2.15.5.1.1.11
Defines whether this port works as User port or as Network port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), user(2), network(3)

prtParamMappingMode		1.3.6.1.4.1.164.6.2.15.5.1.1.12
This object defines path protection on SONET/SDH link Auto - SONET/SDH mapping for port is copied automatically to same TU on the redundant SONET/SDH local (reside on same slot) link by agent. Manual - the user can configure the redundant mapping for port on the same link or to the other link on any TU Adjacent - similar to auto, but mapping is copied automatically by agent to link on adjacent slot .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), off(2), auto(3), manual(4), adjacent(5)

prtParamAlarmIndication		1.3.6.1.4.1.164.6.2.15.5.1.1.13
This object indicates status-aggregation of non-masked alarms associated with all interface layers, related to this physical port. When at least one non-masked alarm exists on any layer, value of this object is on (3). Indication will be off (2) only when there's no active non-masked alarm on any interface layer related to this port. Masking an Alarm, will consider it as not exist for this indication. Example: When a port has an ATM higher layer and at least one VC has alarm, value of this object will be on (3)
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), off(2), on(3)

prtParamClkQualityLevel		1.3.6.1.4.1.164.6.2.15.5.1.1.14
This parameter indicates quality level of clock signal. Quality is encoded according to SSM (Synchronization Status Messages) encoding. Bits 8 -5 of byte are encoded as follows (when bit1=0): Left most bit - MSB(8) ---> LSB(5) 8765 0000 Quality Unknown 0010 PRC (Primary Reference Clock) - Rec. G.811 0100 SSU-T (Sync. Source Unit-Transit)- Rec. G.812 Transit 1000 SSU-L (Sync. Source Unit Local) - Rec. G.812 Local 1011 SEC (SDH Equipment Clock) 1111 DNU (do not use for synchronization) 0001 PRS (=ST1 = Stratum 1 Traceable) 0111 ST2 (Stratum 2 Traceable) 1010 ST3 (Stratum 3 Traceable) 1100 SMC (SONET Minimum Clock Traceable) 1101 Stratum 3E Traceable bit1 = '1' - indicates all octet is Not Applicable
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(1)

prtParamClkWaveShape		1.3.6.1.4.1.164.6.2.15.5.1.1.15
Wave shape of station clock source signal.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), sine(2), square(3)

prtParamStatus		1.3.6.1.4.1.164.6.2.15.5.1.1.16
Station clock source Status.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), up(2), signalLoss(3), syncLoss(4)

prtParamSignalLevel		1.3.6.1.4.1.164.6.2.15.5.1.1.17
This object indicates signal level (in thenth of dB units) on selected port.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtParamClkUserQualityLevel		1.3.6.1.4.1.164.6.2.15.5.1.1.18
This parameter allows user to mark quality level of clock. Quality is encoded according to SSM (Synchronization Status Messages) encoding. Bits 8 -5 of byte are encoded as follows: Left most bit - MSB(8) ---> LSB(5) 8765 0000 Quality Unknown 0010 PRC (Primary Reference Clock) - Rec. G.811 0100 SSU-T (Sync. Source Unit-Transit) Rec. G.812 Transit 1000 SSU-L (Sync. Source Unit Local) - Rec. G.812 Local 1011 SEC (SDH Equipment Clock) 1111 DNU (do not use for synchronization)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(1)

prtParamDataRate		1.3.6.1.4.1.164.6.2.15.5.1.1.19
Rate of serial data port (V.11, V.24, V.35) in kbps units.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

prtParamLoopDetect		1.3.6.1.4.1.164.6.2.15.5.1.1.20
Enable/disable Loop Detection on a port. Examples of ports: physical, Channelized Bundle over TDM Uplink, Bridge Ports.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(2), enable(3)

prtParamActUponLoopDetect		1.3.6.1.4.1.164.6.2.15.5.1.1.21
This parameter is used to indicate which actions should be taken in case a loop is detected in the network the port is part of. Each action is represented by a bit. Currently defined (for RIC155GE/RIC622GE): Bit 0 - Transmit Shut Down Bit 1 - Forward Alarms If bit value = '1' then the action is taken. If bit value = '0' then the actions is not taken.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

prtParamPSNLayer		1.3.6.1.4.1.164.6.2.15.5.1.1.22
This object indicates the network layer from which clock is derived.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	l2(2), l3(3)

prtParamRxSsm		1.3.6.1.4.1.164.6.2.15.5.1.1.23
This object indicates if Station Clock SSM messages received will serve as criteria for clock selection.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(2), rx(3)

prtParamClkSsmRxSource		1.3.6.1.4.1.164.6.2.15.5.1.1.24
This object indicates the Sa-bit of the E1 frame, in which SSM messages are carried.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	sa4(2), sa5(3), sa6(4), sa7(5), sa8(6)

prtParamFarEndDevice		1.3.6.1.4.1.164.6.2.15.5.1.1.26
Programmed Far-End device connected to this port. This object is relevant for products having multiple DBs. It will enable configuring offline, the relevant data. For MP-4100, LRS-102 OP-108/106 cards, the options will be: 1 = None (when a port is not connected to any remote device) 2 = OP-108 3 = OP-108/ETH 4 = OP-106 5 = OP-106/ETH 6 = card of MP or LRS-102
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

prtParamTxClk		1.3.6.1.4.1.164.6.2.15.5.1.1.27
enable/disable station clock signal output.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), enable(3)

prtIP		1.3.6.1.4.1.164.6.2.15.6
OBJECT IDENTIFIER

prtIpParamTable		1.3.6.1.4.1.164.6.2.15.6.1
A table - Parameters for IP Ports.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtIpParamEntry

prtIpParamEntry		1.3.6.1.4.1.164.6.2.15.6.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtIpParamEntry

prtIpParamConfigIdx		1.3.6.1.4.1.164.6.2.15.6.1.1.1
This object indicates the Configuration number (1..255) referred. Value of 255 specifies the TmpCnfg (Scratch). For products having Agent and Edit configurations, Write operation for the table entries is allowed only to Config=255.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtIpParamSlotIdx		1.3.6.1.4.1.164.6.2.15.6.1.1.2
This object indicates a unique number of the slot position in which the module is inserted. notApplicable = 255 (for products that don't have slots). For KM: kmxMlA (103), kmxMlB (104).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtIpParamIdx		1.3.6.1.4.1.164.6.2.15.6.1.1.3
This object indicates a unique Port Index.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtIpParamHostIP		1.3.6.1.4.1.164.6.2.15.6.1.1.4
The host interface IP address.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

prtIpParamHostMask		1.3.6.1.4.1.164.6.2.15.6.1.1.5
The host interface subnet mask.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

prtIpParamDefaultGateway		1.3.6.1.4.1.164.6.2.15.6.1.1.6
Default Gateway's IP Address.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

prtIpParamMediaMode		1.3.6.1.4.1.164.6.2.15.6.1.1.7
This object indicates the real Media Mode.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), halfDuplex(2), fullDuplex(3)

prtIpParamMediaRate		1.3.6.1.4.1.164.6.2.15.6.1.1.8
This object indicates the real Media Rate (Mbps).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), r10Mbps(2), r100Mbps(3)

prtIpParamMngVlanSupport		1.3.6.1.4.1.164.6.2.15.6.1.1.9
Management VLAN support (Tagging). no - No support of VLAN Tagging. yes - 4 VLAN bytes will be added to the frame.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), no(2), yes(3)

prtIpParamMngVlanId		1.3.6.1.4.1.164.6.2.15.6.1.1.10
Management VLAN ID.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtIpParamMngVlanPriority		1.3.6.1.4.1.164.6.2.15.6.1.1.11
Management VLAN Frame priority.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtIpParamRingMode		1.3.6.1.4.1.164.6.2.15.6.1.1.12
This object indicates If Ring Mode is enabled or not.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), enable(3)

prtIpParamProtIpEnable		1.3.6.1.4.1.164.6.2.15.6.1.1.13
This object indicates whether a list of Protected IP Addresses is enabled or not. This object is applicable only if prtIpParamRingMode=enable.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), enable(3)

prtIpParamTrafficPriority		1.3.6.1.4.1.164.6.2.15.6.1.1.14
This object indicates the traffic priority of this port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), low(2), high(3)

prtIpParamRemoteIP		1.3.6.1.4.1.164.6.2.15.6.1.1.15
This is the IP Address of the remote device that is connected to the current device (Point to Point Application). It is used for sending OAM packets on the LAN to the remote side in order to check that the connection is OK.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

prtIpParamMaxTxBandwidth		1.3.6.1.4.1.164.6.2.15.6.1.1.16
This object shows the Max Bandwidth allowed on the LAN. Full - means that a Maximum of 100 Mega Byte Rate may go through the LAN. e1(3) means that the maximum is an E1 rate. t1(4) is for a maximum of a T1 rate.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	full(2), e1(3), t1(4)

prtIpParamTos		1.3.6.1.4.1.164.6.2.15.6.1.1.17
TOS = Type of Service transmitted. Valid values: 0..255.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtIpParamConnect		1.3.6.1.4.1.164.6.2.15.6.1.1.18
Port Connection.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), no(2), yes(3)

prtIpParamAgingTime		1.3.6.1.4.1.164.6.2.15.6.1.1.19
Aging Time in seconds.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtIpParamEncapsulationProt		1.3.6.1.4.1.164.6.2.15.6.1.1.20
Encapsulation Protocol.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), tcp(2), udp(3)

prtIpParamEncapProtPort		1.3.6.1.4.1.164.6.2.15.6.1.1.21
Encapsulation Protocol Port (TCP/UDP Port).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtIpParamVlanSupport		1.3.6.1.4.1.164.6.2.15.6.1.1.22
VLAN support (Tagging). 'no' - No support of VLAN Tagging. 'yes' - 4 VLAN bytes will be added to the frame.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), no(2), yes(3)

prtIpParamVlanId		1.3.6.1.4.1.164.6.2.15.6.1.1.23
VLAN Identifier.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtIpParamVlanPriority		1.3.6.1.4.1.164.6.2.15.6.1.1.24
VLAN Frame priority.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtIpParamDoubleTagVlanId		1.3.6.1.4.1.164.6.2.15.6.1.1.25
VLAN Identifier of the Double Tagging VLAN.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtIpParamDoubleTagVlanPriority		1.3.6.1.4.1.164.6.2.15.6.1.1.26
VLAN Frame priority of the Double Tagging VLAN.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtIpParamVlanTagging		1.3.6.1.4.1.164.6.2.15.6.1.1.27
VLAN Tagging. 'unmodified' - No change will be done to the Frame. 'tag' - Add Tag to Untagged Frames. 'doubleTag' - Add Tag to all Frames. 'doubleTagAndFallBack' - Double Tagging will have different rules for VLANs that this port is member in, than these it is not a member in. 'untag' - Remove Tag from tagged frames.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), unmodified(2), tag(3), doubleTag(4), doubleTagAndFallBack(5), untag(6)

prtIpParamRateLimit		1.3.6.1.4.1.164.6.2.15.6.1.1.28
The maximum rate permitted to transfer via this port, in Kbps.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtIpParamDefInterface		1.3.6.1.4.1.164.6.2.15.6.1.1.29
The Default Interface for packets with unresolved destination subnet. For internal-X port: 100 + X .
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtIpParamMng		1.3.6.1.4.1.164.6.2.15.6.1.1.30
This object indicates whether Management is enabled/disabled via this port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), enable(3)

prtIpParamFloodedRateLimit		1.3.6.1.4.1.164.6.2.15.6.1.1.31
The maximum rate permitted to transfer broadcast, multicast, and unicast flooded frames via this port, in Kbps. 0 - Disable. In Ipmux14 this parameter is applicable when prtIpParamRateLimit=0 (disable).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtIpParamBurstSize		1.3.6.1.4.1.164.6.2.15.6.1.1.32
The burst size that the port can support beyond rate limitation determined in prtIpParamRateLimit. Burst Size is measured in bytes.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

prtIpParamLimitPacketType		1.3.6.1.4.1.164.6.2.15.6.1.1.33
The packet type that will be rate limited. Rate limitation determined in prtIpParamRateLimit. all - All packet types are rate limited. broadMultiFloodedUnicast - Broadcast, Multicast and Flooded Unicast packets are rate limited. broadcastMulticast - Broadcast and Multicast packets are rate limited. broadcast - Broadcast packets are rate limited.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	all(1), broadMultiFloodedUnicast(2), broadcastMulticast(3), broadcast(4)

prtIpParamKeepAliveInterval		1.3.6.1.4.1.164.6.2.15.6.1.1.34
This parameter indicates the period of time (in msec.) between two consequent Keep Alive messages.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtIpParamKeepAliveThresh		1.3.6.1.4.1.164.6.2.15.6.1.1.35
This parameter indicates the maximum number of missed Keep Alive answer messages acceptable, after which link status will be failed.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtIpParamP2pKeepAliveVlanId		1.3.6.1.4.1.164.6.2.15.6.1.1.36
Dedicated VLAN ID for keep alive messages.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtIpParamP2pKeepAliveVlanPrio		1.3.6.1.4.1.164.6.2.15.6.1.1.37
VLAN priority for P2P keep alive messages .
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtIpParamRingAdjacentMacAddr		1.3.6.1.4.1.164.6.2.15.6.1.1.38
The MAC address of the adjacent NE connected to this port in an ETH ring. If the port is not a member of a ring, the value of this parameter will be 00-00-00-00-00-00.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

prtClkSrc		1.3.6.1.4.1.164.6.2.15.7
OBJECT IDENTIFIER

prtClkSrcTable		1.3.6.1.4.1.164.6.2.15.7.1
A table - Parameters for master and fallback clock source of ports .
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtClkSrcEntry

prtClkSrcEntry		1.3.6.1.4.1.164.6.2.15.7.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtClkSrcEntry

prtClkSrcCnfgIdx		1.3.6.1.4.1.164.6.2.15.7.1.1.1
This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..255

prtClkSrcPrtIdx		1.3.6.1.4.1.164.6.2.15.7.1.1.2
This object indicates a unique Port Index (receiving clock). Refer to device specification for port Index
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

prtClkSrcIdx		1.3.6.1.4.1.164.6.2.15.7.1.1.3
An index in the table. master - refers Master clock parameters fallback - refers Fallback clock parameters
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	master(1), fallback(2)

prtClkSrcMode		1.3.6.1.4.1.164.6.2.15.7.1.1.4
This entry indicates the source the nodal timing is locked to.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	internal(2), rxClk(3), notApplicable(255)

prtClkSrcPrt		1.3.6.1.4.1.164.6.2.15.7.1.1.5
This entry is valid only when working in rxClk mode. It specifies the port from which the clock willl be taken. Refer to device specification for source port Index
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

opticalPort		1.3.6.1.4.1.164.6.2.15.8
OBJECT IDENTIFIER

optPrtMonitorTable		1.3.6.1.4.1.164.6.2.15.8.1
A table - optical port (e.g SFP) monitoring parameters, according to SFF-8472 Specification for Diagnostic Monitoring Interface for Optical Xcvrs. and ITU-T rec. G.958
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		OptPrtMonitorEntry

optPrtMonitorEntry		1.3.6.1.4.1.164.6.2.15.8.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	OptPrtMonitorEntry

optPrtMonitorPrtIdx		1.3.6.1.4.1.164.6.2.15.8.1.1.1
This object indicates a unique (optical) Port Index . Refer to device specification for port Index.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

optPrtMonitorSample		1.3.6.1.4.1.164.6.2.15.8.1.1.2
This index indicates historic and current values - minimum, maximum and actual (current) value.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	actual(1), minimum(2), maximum(3)

optPrtMonitorTxPower		1.3.6.1.4.1.164.6.2.15.8.1.1.3
Transmitted optical power level. Value is given in units of hundredth (1/100) of dBm.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

optPrtMonitorLaserBias		1.3.6.1.4.1.164.6.2.15.8.1.1.4
LASER bias current level. Value is given in units of microAmper (uA).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

optPrtMonitorLaserTemp		1.3.6.1.4.1.164.6.2.15.8.1.1.5
LASER temperature level, in hundredth (1/100) (C) degrees.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

optPrtMonitorRxPower		1.3.6.1.4.1.164.6.2.15.8.1.1.6
Received optical power in units of hundredth (1/100) of dBm.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

optPrtMonitorSupplyVoltage		1.3.6.1.4.1.164.6.2.15.8.1.1.7
Supply voltage, in hundredth (1/100) of volts (V).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

optPrtCnfgTable		1.3.6.1.4.1.164.6.2.15.8.2
A table - optical port configuration
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		OptPrtCnfgEntry

optPrtCnfgEntry		1.3.6.1.4.1.164.6.2.15.8.2.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	OptPrtCnfgEntry

optPrtCnfgIdx		1.3.6.1.4.1.164.6.2.15.8.2.1.1
This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.x.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

optPrtCnfgPrtIdx		1.3.6.1.4.1.164.6.2.15.8.2.1.2
This object indicates a unique (optical) Port Index . Refer to device specification for port Index.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

optPrtCnfgALS		1.3.6.1.4.1.164.6.2.15.8.2.1.3
enable/disable Automatic Laser Shutdown
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), enable(3)

systemResetAllStatsCmd		1.3.6.1.4.1.164.6.2.16
Reset statistics of all ports and connections of the device.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

systemClearTablesCmd		1.3.6.1.4.1.164.6.2.17
tempCnfgTables - Set *RowStatus = destroy for all entries of some tables having *RowStatus object, for temporary configuration only! (255). For the relevant tables, see product's specification. This object should be used by WAN product applications before performing the Update operation, in order to clear old entries of these tables. For MP-104/204 the entries will be destroyed for cnfg=1. off - agent will automatically change to this value, after performing the command.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), tempCnfgTables(3)

systemParameter		1.3.6.1.4.1.164.6.2.18
This parameter can be used for different purposes: - TELNET session time-out in seconds. - Ace20: when trying to create row in a table that already has row with the same values, if set of values has to be unique in table, this attribute is set to the index of the existing row. - Optimux-T3: when CH interfaces are RJ-45, user can select via this object, the interface type for each Group of channels: T1 or E1: The selection will be a sum of the following Bits. '0' = T1 '1' = E1 Bit Group Value for each Bit having '1' 1 1 (CH-1..CH-8) 1 2 2 (CH-9..CH-12) 2 3 3 (CH-13..CH-20) 4 4 4 (CH-21..CH-28) 8 Examples: 15 = all Groups are selected to be E1 6 = Group 2 and Group 3 are selected to be E1 (Group 1 and Group 4 are T1). - FCD-A, FCD-M: user can select via this object the configuration used for Get values of MSDSL parameters that don't have configuration index. 1 =active configuration 255=temporary configuration. Set of this object should be done before Getting the MSDSL RW parameters. - Ace2002: This parameter indicates the number of intervals that were successfully uploaded upon statistics collection session. - FCD-IP, WR, FCD-IPD, LA-240: This parameter indicates whether Telnet Access is enabled/disabled: Values: 2 - Telnet Access is Disabled. 3 - Telnet Access is Enabled. -Vmux-110: This parameter value equals to maximum number of bundles. -Optimux-155: Simmilar usage to Optimux T3. user can select via this object, interface type T1 or E1 for each Group of channels (LIU): LIU group consists of 7 channels. Up to 12 LIUs are represented (84 T1 Channels). The selection will be a sum of the 2**n For each bit:'0' = T1 ,'1' = E1 Bit Group 1 1 (CH-1 .. CH-7) 2 2 (CH-8 .. CH-14) 3 3 (CH-15 ..CH-21) ... 9 9 (CH-56.. CH-63) ... 10 10 (CH-64..CH-70) 11 11 (CH-71..CH-77) 12 12 (CH-78..CH-84)
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

agnGlobalAlarmMask		1.3.6.1.4.1.164.6.2.19
The value of this attribute determines the alarm traps the agent should mask and not send to the managers. Each bit from a certain octet represents a certain alarm.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

alarmSeverity		1.3.6.1.4.1.164.6.2.20
This object specifies the severity of the alarms.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	event(3), minor(4), major(5), warning(6), critical(7)

alarmState		1.3.6.1.4.1.164.6.2.21
.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), on(3)

agnTestStatus		1.3.6.1.4.1.164.6.2.22
Indicates the current test status (for all levels: system, card, port). This attribute will be set to: on(3): when there is at least one test in progress on the system/card/port off(2): when there is NO test in progress on the system/card/port
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), on(3)

systemSaveAndResetAllStatsCmd		1.3.6.1.4.1.164.6.2.23
on - a command to Save data of Current Period in Last Period data-set and start a new counting period for Current Period. off - agent will automatically change to this value, after performing the command.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

systemDefaultGateway		1.3.6.1.4.1.164.6.2.24
Default Gateway's IP Address.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

systemPsTable		1.3.6.1.4.1.164.6.2.25
This table describes the PS types of a device. Usage of this table is specified in the device's NMS SRS
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SystemPsEntry

systemPsEntry		1.3.6.1.4.1.164.6.2.25.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SystemPsEntry

systemPsIndex1		1.3.6.1.4.1.164.6.2.25.1.1
First Index. In HUBs: 1 = PS-A slot 2 = PS-B slot 3 = PS-C slot. In SA units: 1 = PS1 2 = PS2 Default = 1
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

systemPsIndex2		1.3.6.1.4.1.164.6.2.25.1.2
Second Index. In HUBs: 1 always. In SA units: 1 = Local 2 = Remote Default = 1.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

systemPsType		1.3.6.1.4.1.164.6.2.25.1.3
The type of PS, for a stand-alone product. acDc - PS that supports both AC and DC. acPF - Power Feeding (phantom) box that is feeding another box by external AC. dcPF - Power Feeding (phantom) box that is feeding another box by external DC.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), ac(2), dc(3), acDc(4), acPF(5), dcPF(6)

systemPsStatus		1.3.6.1.4.1.164.6.2.25.1.4
The Status of the PS unit.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), failed(2), ok(3), degraded(4)

systemPsHotSwap		1.3.6.1.4.1.164.6.2.25.1.5
Is PS unit hot swap or fixed.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), fixed(2), hotSwap(3)

agnFans		1.3.6.1.4.1.164.6.2.26
This entry specifies the FANs existence and status. Each fan will be represented by 2 bits, where the first bit (right) will specify the existence: (0= Not exist, 1=exist), and the left bit will specify it's status (0= OK, 1=FAIL), so for each fan: 00 - FAN does not exist 01 - FAN exists and OK (Low Mode) 10 - High Mode (FAN OK) 11 - FAN exists and is Failed bits 0-1 are for first fan bits 2-3 are for 2nd fan (if exists) bits 4-5 are for 3nd fan (if exists) bits 6-7 are for 4nd fan (if exists) bits 8-9 are for 5nd fan (if exists) bits 10-11 are for 6nd fan (if exists) bits 12-13 are for 7nd fan (if exists) bits 14-15 are for 8nd fan (if exists).
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

agnSendTrapParameter		1.3.6.1.4.1.164.6.2.27
This object specifies if the agent will attach a specific parameter to a trap. For ACE2002 the agent will attach or not the openViewSeverity parameter according to the value of this parameter: 1 - will attach openViewSeverity. 0 - will not attach openViewSeverity.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

agnSensorsStatus		1.3.6.1.4.1.164.6.2.28
This entry specifies the Sensors (Temperature sensors or others) existence and status. Each sensor will be represented by 2 bits, where the first bit (right) will specify the existence: (0= Not exist, 1=exist), and the left bit will specify it's status (0= OK, 1=FAIL), so for each sensor: 00 - sensor does not exist 01 - sensor exists and status is OK 11 - sensor exists and status is not OK ( e.g. temperature exceeds pre-defined threshold) bits 0-1 are for first sensor bits 2-3 are for 2nd sensor (if exists) and so on... Bit 0 is the LSB.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

agnStationClockCard		1.3.6.1.4.1.164.6.2.29
This entry specifies the station clock card existence and status. notExist - station clock card (piggy) does not exist. notValid - station clock card exists but clock status is not valid. ok - station clock card exists, and its status is OK When the sepcific reason for clock status not being valid is known, it may be reported by lossOfSync or lossOfSignal values.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), notExist(2), notValid(3), ok(4)

xcIndexNext		1.3.6.1.4.1.164.6.2.30
This object contains an appropriate value to be used for xcIndex when creating entries in the xcTable. The value 0 indicates that no unassigned entries are available. To obtain the xcIndex value for a new entry, the manager issues a management protocol retrieval operation to obtain the current value of this object. After each retrieval, the agent should modify the value to the next unassigned index. After a manager retrieves a value the agent will determine through its local policy when this index value will be made available for reuse.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

xcTable		1.3.6.1.4.1.164.6.2.31
Configuration of system cross-connect entries. The table follows the behavior described in RFC 2515, RFC 1604 regarding the creation deletion and modification of an entry within the table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		XcEntry

xcEntry		1.3.6.1.4.1.164.6.2.31.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	XcEntry

xcIndex		1.3.6.1.4.1.164.6.2.31.1.1
Cross Connect Identifier.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

xcIfIndex1		1.3.6.1.4.1.164.6.2.31.1.2
The interface Index from the ifTable, which identify one side of the connection.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

xcVpi		1.3.6.1.4.1.164.6.2.31.1.3
The VPI value.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

xcVci		1.3.6.1.4.1.164.6.2.31.1.4
The VCI value.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

xcIfIndex2		1.3.6.1.4.1.164.6.2.31.1.5
The interface Index from the ifTable, which identifies the other side of the connection.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

xcRowStatus		1.3.6.1.4.1.164.6.2.31.1.6
This parameter allows NMS to create/delete entries of this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

xcDescr		1.3.6.1.4.1.164.6.2.31.1.7
A textual string containing information about the xc entry.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString

xcAdminStatus		1.3.6.1.4.1.164.6.2.31.1.8
The desired administrative status of this bi-directional cross-connect.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	up(1), down(2)

xcOperStatus		1.3.6.1.4.1.164.6.2.31.1.9
The operational status of this bi-directional cross-connect.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2), unknown(3)

xcAttachedIfType		1.3.6.1.4.1.164.6.2.31.1.10
This object indicates if the specific VCC is already attached to any interface, and indicates the type of the interface. This object's purpose is to ease the checking to the NMS. notApplicable - used for entries that are not LAN (as HDLC), or when the VCC was attached to a bridge, or when this parameter is irrelevant. free - the LAN VCC wasn't attached yet to any router interface. routerAtm - attached to an ATM router interface. lis - attached to a LIS interface.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), free(2), routerAtm(3), lis(4)

xcInputPriority		1.3.6.1.4.1.164.6.2.31.1.11
This object is the priority, by which the LAN frames will be internaly sent to the ATM HW. This parameter is applicable if atmNteMdlInputPriorityMechanism=enabled. 1 - Highest priority. Will be the first to be sent to the ATM HW. 4 - Lowest priority. Will be the last to be sent to the ATM HW.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..4

xcBitMapping		1.3.6.1.4.1.164.6.2.31.1.12
This object maps this entry to a bit of an octet string. For ACE2002 this object maps the LAN VCC to the bit of the VLAN Port Lists. If the value is '0' then it means that this VCC is not mapped to a port list or it may be an HDSL entry.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

systemModule		1.3.6.1.4.1.164.6.2.32
OBJECT IDENTIFIER

modlParam		1.3.6.1.4.1.164.6.2.32.1
OBJECT IDENTIFIER

modlParamTable		1.3.6.1.4.1.164.6.2.32.1.1
This table include parameters for system modules.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ModlParamEntry

modlParamEntry		1.3.6.1.4.1.164.6.2.32.1.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	ModlParamEntry

modlParamIndex		1.3.6.1.4.1.164.6.2.32.1.1.1.1
The module index. The index can be the slot number or any other module index as described in the specifications of the device. For Vmux-2100 device, the index will have values of: 1..4 for slots 1..4.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

modlParamReset		1.3.6.1.4.1.164.6.2.32.1.1.1.2
Reset action to be performed on the module. Set the parameter will be done always to on(3) or factory (4). After performing the Reset operation, Agent will automatically set the parameter to off(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3), factory(4)

modlParamSwdlStatus		1.3.6.1.4.1.164.6.2.32.1.1.1.3
This parameter indicates whatever the swdl is in process or not.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), off(2), inProcess(3)

modlParamLeds		1.3.6.1.4.1.164.6.2.32.1.1.1.4
This entry specifies the LEDs status of the module. Each led is represented by 4 bits where the first 2 bits (left) specify the status : (00=NA, 01=OFF, 10=ON, 11=BLINK), and the next two bits (right) specify the color : (00=GREEN, 01=RED, 10=YELLOW, 11=GRAY). The order of the LEDS is from top to bottom, left to right: For each row starting from the top, the LEDS are returned from left to right.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

modlParamType		1.3.6.1.4.1.164.6.2.32.1.1.1.5
This attribute indicates the Module Type.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(2), empty(3), miRicE1(4), miRicT1(5), miRicE3(6), miRicT3(7)

modlParamSwVer		1.3.6.1.4.1.164.6.2.32.1.1.1.6
This attribute indicates the Module's Software Version.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

agnNearFarConnection		1.3.6.1.4.1.164.6.2.33
This parameter describes the connection between near-end and far-end agents.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), disconnected(2), connected(3)

agnAccess		1.3.6.1.4.1.164.6.2.34
OBJECT IDENTIFIER

agnTelnetAccess		1.3.6.1.4.1.164.6.2.34.1
Enable/Disable accessing the device via Telnet. disable - no one will be allowed to access the device via Telnet. enable - all users are allowed Telnet Access. managersOnly - Only manager stations listed in the manager's list are allowed. enableSecure - same as 'enable' above + only Secure data will be accepted (SSH) managersOnlySecure - same as 'managersOnly' above + only Secure data will be accepted (SSH).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(2), enable(3), managersOnly(4), enableSecure(5), managersOnlySecure(6)

agnWebAccess		1.3.6.1.4.1.164.6.2.34.2
Enable/Disable accessing the device via Web. disable - no one will be allowed to access the device via Web. enable - all users are allowed Web Access. managersOnly - Only manager stations listed in the manager's list are allowed. enableSecure - same as 'enable' above + only Secure data will be accepted (SSL) managersOnlySecure - same as 'managersOnly' above + only Secure data will be accepted (SSL).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(2), enable(3), managersOnly(4), enableSecure(5), managersOnlySecure(6)

agnRadiusAccess		1.3.6.1.4.1.164.6.2.34.3
Enable/Disable authentication via RADIUS server.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(2), enable(3)

agnSshAccess		1.3.6.1.4.1.164.6.2.34.4
Enable/Disable accessing the device via SSH. disable - no one will be allowed to access the device via SSH. enable - all users are allowed SSH Access. managersOnly - Only manager stations listed in the manager's list are allowed.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(2), enable(3), managersOnly(4)

systemInterface		1.3.6.1.4.1.164.6.2.35
OBJECT IDENTIFIER

ifCreateTable		1.3.6.1.4.1.164.6.2.35.1
The Interface Configuration Table. This table enables to create interfaces of Entities.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IfCreateEntry

ifCreateEntry		1.3.6.1.4.1.164.6.2.35.1.1
An entry in the Interface Configuration table.
Status: current	Access: not-accessible
OBJECT-TYPE
	IfCreateEntry

ifCreateEntityType		1.3.6.1.4.1.164.6.2.35.1.1.1
This object indicates the Type of the Entity that exists above the created interface. For a Logical Port, this value can be: other (1) when there is no fixed entity above it.
Status: current	Access: read-only
OBJECT-TYPE
	SysIfEntityType

ifCreateEntityIdx		1.3.6.1.4.1.164.6.2.35.1.1.2
This object indicates the Index of the Entity that exists above the created interface. For a Logical Port, this value can be: 9999 - N/A when there is no fixed entity above it.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ifCreateNumber		1.3.6.1.4.1.164.6.2.35.1.1.3
This object indicates the number of the Interface that is created.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ifCreateRowStatus		1.3.6.1.4.1.164.6.2.35.1.1.4
This object enables the user to create/delete entries in this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

ifCreateType		1.3.6.1.4.1.164.6.2.35.1.1.5
This object indicates the Type of the Interface that is created.
Status: current	Access: read-create
OBJECT-TYPE
	IANAifType

ifCreateIndex		1.3.6.1.4.1.164.6.2.35.1.1.6
This object indicates the ifIndex of the created Interface. The ifIndex is assigned by the device.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ifCreateConnectedTo		1.3.6.1.4.1.164.6.2.35.1.1.7
This object indicates the entity connected to the created Interface. The value of this object can be ifIndex of the connected entity or any other number that can identify it.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

ifCreateParams		1.3.6.1.4.1.164.6.2.35.1.1.8
This object represents one or more parameters of the created Interface. Each group of bits (one or more bits) represents a specific parameter and its possible values. This object's mapping and interpretation will be specified in each device's specification documents. The parameter should be used within the create PDU assuming atomic operation.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

ifCreateConnectionPointer		1.3.6.1.4.1.164.6.2.35.1.1.9
This parameter represents the entity that is connected to this Interface. It can be used instead of ifCreateConnectedTo. It is an OBJECT IDENTIFIER. This parameter's SYNTAX allows the following possibilities: - can be simply used for entity that is not an interface - is not limited to include up to 32 bits The value of this parameter is a pointer to an existing row of a table, where the entity connected to this Interface is defined (i.e. the pointer uniquely identifies the connected entity). Examples: In case of an interface (from 2863.ifTable): points to 'ifEntry' of corresponding row = . In case of a VPI/VCI (from 2515.atmVclTable): points to 'atmVclEntry' of corresponding row = ..VPI.VCI In case no entity is connected, value = 0 .
Status: current	Access: read-create
OBJECT-TYPE
	RowPointer

interfacePerformance		1.3.6.1.4.1.164.6.2.35.2
OBJECT IDENTIFIER

ifPerfTable		1.3.6.1.4.1.164.6.2.35.2.1
Interface Performance Table. The propose of this table is to support statistics counters having 64 bit by using 2 parameters with syntax= Integer32. This is because SNMPv1 does not support Counter64 properly. For SNMPv3, ifPerfHCCounter (Counter64) may be supported.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IfPerfEntry

ifPerfEntry		1.3.6.1.4.1.164.6.2.35.2.1.1
An entry in the Interface Performance Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	IfPerfEntry

ifPerfCounterType		1.3.6.1.4.1.164.6.2.35.2.1.1.1
2nd index of the ifPerfTable. This parameter represents the Counter Type. Each application can have a different association between this object's value and counter type - see relevant application spec. For VPLS-MTU application use the following values: 1= Rx Octets, 2= Tx Octets, 3= Rx Frames, 4= Tx Frames, 5=Rx Dropped Frames, 6= Tx Dropped Frames. Optionally, counter type description appears in agnListDecodingTable
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

ifPerfLowCounterPart		1.3.6.1.4.1.164.6.2.35.2.1.1.2
In order to support Counters having 64 bit length, the performance counter is divided into two 32 bit parameters as follows: [ 64 bit parameter ] = [ High 32 bit parameter ][ Low 32 bit parameter ]. This parameter holds the Low 32 bits of the counter, while the following parameter holds the High 32 bits of the counter.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

ifPerfHighCounterPart		1.3.6.1.4.1.164.6.2.35.2.1.1.3
This parameter holds the High 32 bits of the counter (see description in the above parameter).
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

ifPerfHCCounter		1.3.6.1.4.1.164.6.2.35.2.1.1.4
This High Capacity counter holds whole 64 bits of the counter indicated by ifPerfCounterType (concatenates both counter parts ifPerfHighCounterPart&ifPerfLowCounterPart) This object can be supported only by agents using SNMPv2 or SNMPv3.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

systemOam		1.3.6.1.4.1.164.6.2.36
OBJECT IDENTIFIER

systemOamTable		1.3.6.1.4.1.164.6.2.36.1
The OAM Configuration Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SystemOamEntry

systemOamEntry		1.3.6.1.4.1.164.6.2.36.1.1
An entry in the OAM table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SystemOamEntry

systemOamCnfgIdx		1.3.6.1.4.1.164.6.2.36.1.1.1
This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..255

systemOamFrequency		1.3.6.1.4.1.164.6.2.36.1.1.2
Time in sec. between 2 OAM packets.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

systemOamTimeoutCycles		1.3.6.1.4.1.164.6.2.36.1.1.3
No. of cycles the agent will send OAM packets without receiving a response from the remote device before declaring that the connection to the remote side is down - Time Out.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

systemOamLinkCheck		1.3.6.1.4.1.164.6.2.36.1.1.4
This MIB object determines whether continuous connectivity Link checks will be performed by the device for uplinks. For Vmux-2100: enable (3) value can be set upon device installation. In this case, TDM Link Connectivity checks can be performed even before the user configures the Links of the device.If the value is enable (3) and there is no connection with the remote side, the Test LED will blink on the Main Board Module.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(2), enable(3)

systemOamDescrTable		1.3.6.1.4.1.164.6.2.36.2
The OAM Descriptors Configuration Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SystemOamDescrEntry

systemOamDescrEntry		1.3.6.1.4.1.164.6.2.36.2.1
An entry in the OAM table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SystemOamDescrEntry

systemOamDescrIdx		1.3.6.1.4.1.164.6.2.36.2.1.1
The OAM Descriptor Index.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

systemOamDescrRowStatus		1.3.6.1.4.1.164.6.2.36.2.1.2
Enables the user to create/delete entries in this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

systemOamDescrMode		1.3.6.1.4.1.164.6.2.36.2.1.3
The OAM Mode of the Descriptor.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	intermediate(1), segmentTermination(2), endToEndTermination(3)

systemOamDescrCCDirection		1.3.6.1.4.1.164.6.2.36.2.1.4
OAM Continuity Check function mode. both(2) - Agent sends OAM CC cells and checks received OAM CC cells. none(3) - Agent does not send and does not check received OAM CC cells. source(4)- Agent sends OAM CC cells. sink(5) - Agent checks received OAM CC cells.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	both(2), none(3), source(4), sink(5)

systemOamDescrLoopbackOperation		1.3.6.1.4.1.164.6.2.36.2.1.5
The OAM Loopback function mode. off(2) - Stop sending loopback OAM cells. on(3) - Start loopback OAM cells.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	off(2), on(3)

systemOamDescrLoopbackDestAddr		1.3.6.1.4.1.164.6.2.36.2.1.6
Loopback Destination Address.
Status: current	Access: read-create
OBJECT-TYPE
	OCTET STRING

systemOamDescrXcCounter		1.3.6.1.4.1.164.6.2.36.2.1.7
The number of connections that use this OAM Descriptor.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

agnDeviceView		1.3.6.1.4.1.164.6.2.37
This variable denotes the view of the device: Look: old look, new look or new look 2. Material: Plastic or Metal.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	oldLook(2), newLook(3), newLook2(4), plastic(5), metal(6)

bitMappingTable		1.3.6.1.4.1.164.6.2.38
This table maps bits of an octet string to an interface. For ACE-2002 this table is used to map bits of VLAN port lists to LAN VCC's. This table is the opposite view of the xcTable for xcBitMapping. It is used to ease the bit translation for the NMS.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		BitMappingEntry

bitMappingEntry		1.3.6.1.4.1.164.6.2.38.1
Each entry in the table describes a correlation of a bit location to an interface. For ACE-2002 - Upon creation of a new LAN VCC the agent will add an entry to this table that will define the bit location for that VCC.
Status: current	Access: not-accessible
OBJECT-TYPE
	BitMappingEntry

bitMappingLocation		1.3.6.1.4.1.164.6.2.38.1.1
The bit location in an octet string.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

bitMappingIndex		1.3.6.1.4.1.164.6.2.38.1.2
The interface index or any other index that should be mapped.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

bitMappingView		1.3.6.1.4.1.164.6.2.39
A view of the bitMappingTable in one object - each entry in the biMappingTable will have the corresponding Bit of this object (bitMappingLocation) = '1'. For ACE-2002 it is used to describe all the existing LAN VCC's So that the NMS can easily calculate which VCC's can be selected as members for a VLAN, instead of reading all the bitMapping Table.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

hostTable		1.3.6.1.4.1.164.6.2.40
Host interface table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HostEntry

hostEntry		1.3.6.1.4.1.164.6.2.40.1
An entry in the Host Table. The hostParam1, hostParam2, and hostParam3 entries may have different use in different applications.
Status: current	Access: not-accessible
OBJECT-TYPE
	HostEntry

hostIndex		1.3.6.1.4.1.164.6.2.40.1.1
The Host Table Index. This index can have the same value as Host No.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

hostIP		1.3.6.1.4.1.164.6.2.40.1.2
The host interface IP address.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

hostIPMask		1.3.6.1.4.1.164.6.2.40.1.3
The host interface subnet mask.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

hostDefaultNextHop		1.3.6.1.4.1.164.6.2.40.1.4
The host interface Default Next Hop address.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

hostMode		1.3.6.1.4.1.164.6.2.40.1.5
This parameter represents the Host mode of operation. There can be different values for each application. For example: Not Applicable = 1.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

hostParam1		1.3.6.1.4.1.164.6.2.40.1.6
This parameter represents the first Host parameter. There can be different values for each application. For example: Not Applicable = 1.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

hostParam2		1.3.6.1.4.1.164.6.2.40.1.7
This parameter represents the 2nd Host parameter. There can be different values for each application.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

hostParam3		1.3.6.1.4.1.164.6.2.40.1.8
This parameter represents the 3nd Host parameter. There can be different values for each application.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

hostRowStatus		1.3.6.1.4.1.164.6.2.40.1.9
Creation/Deletion of rows in the table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

hostVlanTagging		1.3.6.1.4.1.164.6.2.40.1.10
Host VLAN support (Tagging). untag - No support of VLAN Tagging. tag - 4 VLAN bytes will be added to the frame.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notApplicable(1), untag(2), tag(3)

hostVlanId		1.3.6.1.4.1.164.6.2.40.1.11
Host VLAN ID.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

hostVlanPriority		1.3.6.1.4.1.164.6.2.40.1.12
Host VLAN Frame priority.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

invNameXCTable		1.3.6.1.4.1.164.6.2.41
Inverse Name XC Table. This table can be used to ease the search for a connection first index by the connection name.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		InvNameXCEntry

invNameXCEntry		1.3.6.1.4.1.164.6.2.41.1
An entry in the table.
Status: current	Access: not-accessible
OBJECT-TYPE
	InvNameXCEntry

invNameXC		1.3.6.1.4.1.164.6.2.41.1.1
The unique Connection name, associated to a Cross-Connection.
Status: current	Access: not-accessible
OBJECT-TYPE
	SnmpAdminString	Size(1..64)

invNameXCType		1.3.6.1.4.1.164.6.2.41.1.2
The OBJECT IDENTIFIER of the respective XC Table. Examples: XC Table invNameXCType --------------------------------------------------- atmVpCrossConnectTable 1.3.6.1.2.1.37.1.9 atmVcCrossConnectTable 1.3.6.1.2.1.37.1.11 atmfCESConfTable 1.3.6.1.4.1.353.5.2.2.1.1 .
Status: current	Access: read-only
OBJECT-TYPE
	OBJECT IDENTIFIER

invNameXCIndex		1.3.6.1.4.1.164.6.2.41.1.3
The XC Table (invNameXCType) may include more than one index. This object represents the value of the first XC Index.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnDeviceCapabilities		1.3.6.1.4.1.164.6.2.42
Indicates the optional capabilities that are implemented by this device and are manageable through this MIB. For each capability 1 BIT is allocated in each Octet starting from the LSB. If the value of the BIT = 1, the capability is Enabled. If the value of the BIT = 0, the capability is Disabled. For bit assignment, refer to device specification. Capabilities example: Router - BIT 0 (0000 0001 = 01 Hex = 1 Decimal). The 2nd octet (MSB) will represent the maximum number of intervals that the Agent can keep in its DB (same for all ports). For Vmux, this object describes agent's support of LBRAD coder feature: 1 octet ; bit 0 (LSB). '1' - LBRAD feature is supported '0' - LBRAD feature is not supported.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

rowInfoTable		1.3.6.1.4.1.164.6.2.43
This table holds information of other tables.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RowInfoEntry

rowInfoEntry		1.3.6.1.4.1.164.6.2.43.1
An entry in the table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RowInfoEntry

rowInfoTableId		1.3.6.1.4.1.164.6.2.43.1.1
The OBJECT IDENTIFIER of the Table, which its information is held by this table (rowInfoTable). Examples: Table Name rowInfoTableId --------------------------------------------------- atmTrafficDescrParamTable 1.3.6.1.2.1.37.1.5 atmVpCrossConnectTable 1.3.6.1.2.1.37.1.9 atmVcCrossConnectTable 1.3.6.1.2.1.37.1.11 atmfCESConfTable 1.3.6.1.4.1.353.5.2.2.1.1 .
Status: current	Access: not-accessible
OBJECT-TYPE
	OBJECT IDENTIFIER

rowInfoCounter		1.3.6.1.4.1.164.6.2.43.1.2
The Number of rows in the table, indicated by rowInfoTableId.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rowInfoIndexNext		1.3.6.1.4.1.164.6.2.43.1.3
The First Free Index of the table, indicated by rowInfoTableId.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rowInfoMaxNoOfRows		1.3.6.1.4.1.164.6.2.43.1.4
The maximum possible number of rows in the table, indicated by rowInfoTableId.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnStoreCmd		1.3.6.1.4.1.164.6.2.44
Store command. inFlash(3) = store the current Agent configuration in Flash memory. asDefConfigFile(4) = store the current Agent configuration as Default Configuration file (e.g. 'DefConfig.cfg'). Agent will perform the required command and change automatically the value of this object to off(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), inFlash(3), asDefConfigFile(4)

agnFunctionTable		1.3.6.1.4.1.164.6.2.45
This table is used in order to activate/deactivate device functions. The index indicates the function. Each function can be Enabled or Disabled.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AgnFunctionEntry

agnFunctionEntry		1.3.6.1.4.1.164.6.2.45.1
An entry in the table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AgnFunctionEntry

agnFunction		1.3.6.1.4.1.164.6.2.45.1.1
This MIB object indicates the function that will be enabled or disabled in the device. alarmForwarding= Fault Propagation (usually towards user port). For Vmux: routing (2) - enable/disable Router backup (3) - enable/disable Backup between E1/T1/Serial Link and ETH. uplinkLoopDetect (5) - enable/disable Loop Detection on the TDM Uplink. systemClock (6) - enable/disable the System Clock.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	routing(2), backup(3), alarmForwarding(4), uplinkLoopDetect(5), systemClock(6)

agnFunctionActivation		1.3.6.1.4.1.164.6.2.45.1.2
This MIB object indicates the activation of the current function.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(2), enable(3)

agnManagerConfigPorts		1.3.6.1.4.1.164.6.2.46
This variable defines from which port/s this manager can manage the device. The value is a sum of 2**n, where n is a bit assigned to a certain port. For RIC-E1 and ETX 102 the value will be according to the ports combination: Network = bit 0 User= bit 1 For Example: All = 3.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

agnEgressRateRange		1.3.6.1.4.1.164.6.2.47
This variable defines the valid ranges of egress rate. For example, for ETX 102: range 1 (2)= 128KBPS - 8MBPS, range 2 (3)= 256KBPS - 16MBPS, range 3 (4)= 512KBPS - 32MBPS, range 4 (5)= 1MBPS - 64MBPS, range 5 (6)= 1.5MBPS - 80MBPS.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unlimited(1), range1(2), range2(3), range3(4), range4(5), range5(6), range6(7), range7(8)

agnNoOfCurrentConns		1.3.6.1.4.1.164.6.2.48
This variable indicates the number of connections currently configured for the agent.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnIngressRateRange		1.3.6.1.4.1.164.6.2.49
This variable defines the valid ranges of ingress rate. For example, for ETX 102: range 1 (2)= 128KBPS - 8MBPS, range 2 (3)= 256KBPS - 16MBPS, range 3 (4)= 512KBPS - 32MBPS, range 4 (5)= 1MBPS - 64MBPS, range 5 (6)= 1.5MBPS - 80MBPS.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unlimited(1), range1(2), range2(3), range3(4), range4(5), range5(6), range6(7), range7(8)

alarmForwardingTable		1.3.6.1.4.1.164.6.2.50
The Alarm Forwarding Mechanism will be operated for this table entries.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlarmForwardingEntry

alarmForwardingEntry		1.3.6.1.4.1.164.6.2.50.1
Each entry in this table is a pair of ports that the Alarm Forwarding Mechanism is determined for.
Status: current	Access: not-accessible
OBJECT-TYPE
	AlarmForwardingEntry

alarmForwardingFailPort		1.3.6.1.4.1.164.6.2.50.1.1
An Index of the port on which a fail occurs.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..2147483647

alarmForwardingToPort		1.3.6.1.4.1.164.6.2.50.1.2
An Index of the port that will be affected upon the failure of the alarmForwardingFailPort.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..2147483647

alarmForwardingRowStatus		1.3.6.1.4.1.164.6.2.50.1.3
Creation/ Deletion of rows in the table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

alarmForwardingRecoveryTime		1.3.6.1.4.1.164.6.2.50.1.4
This parameter defines the maximum time (sec) the affected port will hold the down state.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

alarmForwardingGroupConditions		1.3.6.1.4.1.164.6.2.50.1.5
This parameter is applicable when there is a group of interfaces in which a fault may occur, and one interface to which alarm is propagated (forwarded). 0 = All - Forwarding will take place only when all interfaces of the same group are faulty. 1 = Single - Forwarding will take place when at least one (single) interface of the same group (any of them) is faulty. n - forwarding will take place only when n (n < all) interfaces of the same group fail.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

alarmForwardingCause		1.3.6.1.4.1.164.6.2.50.1.6
Bit map representing the cause upon which alarm forwarding will take place. bit 0 - LOSS (LINE DOWN) bit 1 - AIS bit 2 - RDI bit 3 - PROTOCOL DOWN.
Status: current	Access: read-create
OBJECT-TYPE
	BITS	loss(0), ais(1), rdi(2), protocolDown(3)

alarmForwardingRecoveryMode		1.3.6.1.4.1.164.6.2.50.1.7
This parameter determines the Recovery Mode. manual - The user should stop the alarm forwarding by using the alarmForwardingRecoveryCommand. automatic - Alarm forwarding will be automatically stopped upon alarmForwardingFailPort recovery.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	manual(1), automatic(2)

alarmForwardingRecoveryCommand		1.3.6.1.4.1.164.6.2.50.1.8
This parameter is a command. It is applicable when alarmForwardingRecoveryMode = manual. on - Will stop alarm forwarding. After setting to 'On', the agent will set this parameter back to 'Off'.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	off(2), on(3)

alarmForwardingDelay		1.3.6.1.4.1.164.6.2.50.1.9
This parameter determines the period of time (in seconds) the alarm of the alarmForwardingFailPort should exist before starting alarm forwarding.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

alarmForwardingDirection		1.3.6.1.4.1.164.6.2.50.1.10
This parameter determines the Direction of the Alarm Forwarding. unidirectional - alarmForwardingFailPort affects the alarmForwardingToPort. bidirectional - alarmForwardingFailPort affects the alarmForwardingToPort AND vice-versa. For such cases, this value will be selected, instead of entering an additional unidirectional entry in the table, where the indexes are swapped.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	unidirectional(1), bidirectional(2)

alarmForwardingAction		1.3.6.1.4.1.164.6.2.50.1.11
Bit map representing the action to be performed when alarm forwarding will take place. bit 0 - No Action. '1' value - device should NOT perform any action, though other bits indicate the action to be taken. '0' value - device should perform the action/s indicated by rest of the bits. In this case, one of the other bits should be '1'. bit 1 - Interface Deactivation (of the affected Port: alarmForwardingToPort) bit 2 - OAM Signaling. Affected Port (alarmForwardingToPort) will send special OAM Signaling to the Far-End unit about the Failure. This object will be used only for devices that support Deactivation per entry OR can support more than one action.
Status: current	Access: read-create
OBJECT-TYPE
	BITS	noAction(0), interfaceDeactivation(1), oamSignaling(2)

agnSwVersionSwapCmd		1.3.6.1.4.1.164.6.2.51
SW switch command. mainAndBackup (3) = Swap between Main SW and the backup one. Agent will perform the required command and change automatically the value of this object to off(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), mainAndBackup(3)

agnClockSource		1.3.6.1.4.1.164.6.2.52
OBJECT IDENTIFIER

agnClkSrcPortTable		1.3.6.1.4.1.164.6.2.52.1
Pool of Ports for the Master/Fallback Clock Source and of Recovered IDs. For devices with more than one configuration: Set operation is valid only to the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AgnClkSrcPortEntry

agnClkSrcPortEntry		1.3.6.1.4.1.164.6.2.52.1.1
An entry in the table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AgnClkSrcPortEntry

agnClkSrcPortCnfgIdx		1.3.6.1.4.1.164.6.2.52.1.1.1
This object indicates the Idx of the Cnfg being accessed ; Idx of 255 relates to the TmpCnfg. For product supporting a single configuration, the value will be 1.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..2147483647

agnClkSrcPortSrcIdx		1.3.6.1.4.1.164.6.2.52.1.1.2
Clock Source Index. master - refers to Master clock fallback - refers to Fallback clock recovered - refers to Recovered clock.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	master(1), fallback(2), recovered(3)

agnClkSrcPortIdx		1.3.6.1.4.1.164.6.2.52.1.1.3
This object indicates the running Idx of the port that is to be used as Clock Source, for each agnClkSrcPortSrcIdx instance. In case of Recovered Clock - it indicates the Clock ID.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..2147483647

agnClkSrcPort		1.3.6.1.4.1.164.6.2.52.1.1.4
This object indicates the Port/Interface Index of the port that is to be used as Clock Source. In case of Recovered Clock - it indicates the PW number.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..2147483647

agnClkSrcPortRowStatus		1.3.6.1.4.1.164.6.2.52.1.1.5
This object enables Creation/ Deletion of rows in the table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

agnClkSrcPortAdminStatus		1.3.6.1.4.1.164.6.2.52.1.1.6
This object indicates the Recovered Clock Administrative Status.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notApplicable(1), down(2), up(3)

agnClkSrcPortType		1.3.6.1.4.1.164.6.2.52.1.1.7
This object is relevant only in case of Recovery Clock. It indicates the Clock Type.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notApplicable(1), adaptive(2), ieee1588v2(3), commonClock(4)

agnClkSrcPortQuality		1.3.6.1.4.1.164.6.2.52.1.1.8
This object indicates the Clock Source Quality.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notApplicable(1), stratum1(2), stratum2(3), stratum3(4), stratum3e(5), stratum4(6)

agnClkSrcPortNetType		1.3.6.1.4.1.164.6.2.52.1.1.9
This object is relevant only in case of Recovery Clock. It indicates the Clock Network Type, i.e. the PSN network characteristics and behavior.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notApplicable(1), typeA(2), typeB(3), typeC(4), typeD(5), typeE(6), typeF(7)

agnClkSrcPortState		1.3.6.1.4.1.164.6.2.52.1.1.10
This object indicates the Clock State. freeRun(1) - Clock recovery is not locked to any clock. frequencyAcquisition(2) - Adaptive clock recovery is learning the frequency. rapidPhaseLock(3) - Clock recovery is in training process till it reaches fine phase lock. finePhaseLock(4) - Clock is locked and clock recovery is qualified and stable. holdover(5) - Clock recovery is in holdover mode. notApplicable(6) - Clock recovery is not applicable. .
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	freeRun(1), frequencyAcquisition(2), rapidPhaseLock(3), finePhaseLock(4), holdover(5), notApplicable(6)

agnCurrClkTable		1.3.6.1.4.1.164.6.2.52.2
Current Clock Source.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AgnCurrClkEntry

agnCurrClkEntry		1.3.6.1.4.1.164.6.2.52.2.1
An entry in the table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AgnCurrClkEntry

agnCurrClkObjIdx		1.3.6.1.4.1.164.6.2.52.2.1.1
This MIB object identifies the object for which the Clock Source is used (System, Other System, Card).
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..2147483647

agnCurrClkMode		1.3.6.1.4.1.164.6.2.52.2.1.2
Current Clock Source Mode. master - refers Master clock fallback - refers Fallback clock internal - only when both Master and Fallback Sources failed
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	master(1), fallback(2), internal(3)

agnCurrClkSrc		1.3.6.1.4.1.164.6.2.52.2.1.3
This object indicates the Current Clock Source.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), internal(2), rxClk(3), station(4), lbt(5), ntr(6), adaptive(7), stationB(8), automatic(9), system(10), sSubsystem(11), notApplicable(255)

agnCurrClkPort		1.3.6.1.4.1.164.6.2.52.2.1.4
This object indicates the Port/Interface Index of the port that is Currently used as Clock Source.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..2147483647

agnCurrClkHoldover		1.3.6.1.4.1.164.6.2.52.2.1.5
Current Clock Holdover State. As a last resort, in the absence of higher quality timing: - a SONET/SDH object can enter 'holdover' state, until higher quality external timing becomes available again. In this state (value=yes) the SONET/SDH object uses its own timing circuits for clock of the SONET/SDH signal. - for other objects, the 'holdover'=yes state means that the object uses last available clock (stored by the object) for a pre-defined time, until another clock source is used.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), no(2), yes(3)

agnCurrClkSsmBased		1.3.6.1.4.1.164.6.2.52.2.1.6
This parameter indicates whether clock source is selected based on receive clock quality. Clock quality is indicated in S1 byte inside SONET/SDH overhead, (encoded as SSM - Synchronization Status Messaging).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), no(2), yes(3)

agnCurrClkState		1.3.6.1.4.1.164.6.2.52.2.1.7
This object indicates the Current Clock State. freeRun(1) - Current clock state machine is not locked and run from the internal oscillator. rapidPhaseLock(2) - Current clock state machine is locked. finePhaseLock(3) - Current clock state machine is in pre-locking. holdover(4) - Current clock state machine is in holdover mode (due to loss of event). .
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	freeRun(1), rapidPhaseLock(2), finePhaseLock(3), holdover(4)

agnCurrClkQualification		1.3.6.1.4.1.164.6.2.52.2.1.8
This object indicates the Current Clock Qualification and defines whether the PLL can locked according to the stratum definitions.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), disqualified(2), qualified(3)

agnClockMonitoring		1.3.6.1.4.1.164.6.2.52.3
OBJECT IDENTIFIER

agnClkCurrentTable		1.3.6.1.4.1.164.6.2.52.3.1
The Clock Current table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AgnClkCurrentEntry

agnClkCurrentEntry		1.3.6.1.4.1.164.6.2.52.3.1.1
An entry in the Clock Current table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AgnClkCurrentEntry

agnClkCurrentIndex		1.3.6.1.4.1.164.6.2.52.3.1.1.1
An Index that is uniquely represents the Clock.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

agnClkCurrentRxPackets		1.3.6.1.4.1.164.6.2.52.3.1.1.2
The counter associated with the number of Received Packets, encountered by a Bridge Port in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

agnClkCurrentLostPackets		1.3.6.1.4.1.164.6.2.52.3.1.1.3
The counter associated with the number of Lost Packets, encountered by a Bridge Port in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

agnClkCurrentOutOfOrderPackets		1.3.6.1.4.1.164.6.2.52.3.1.1.4
The counter associated with the number of times Out-of-Order Packets encountered by a Bridge Port in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

agnClkCurrentBufferUnderflow		1.3.6.1.4.1.164.6.2.52.3.1.1.5
The counter associated with the number of times Underflow event encountered by a Bridge Port in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

agnClkIntervalTable		1.3.6.1.4.1.164.6.2.52.3.2
The Clock Interval table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AgnClkIntervalEntry

agnClkIntervalEntry		1.3.6.1.4.1.164.6.2.52.3.2.1
An entry in the Clock Interval table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AgnClkIntervalEntry

agnClkIntervalIndex		1.3.6.1.4.1.164.6.2.52.3.2.1.1
An Index that is uniquely represents the Clock.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

agnClkIntervalNumber		1.3.6.1.4.1.164.6.2.52.3.2.1.2
A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals exist).
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

agnClkIntervalRxPackets		1.3.6.1.4.1.164.6.2.52.3.2.1.3
The counter associated with the number of Received Packets, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

agnClkIntervalLostPackets		1.3.6.1.4.1.164.6.2.52.3.2.1.4
The counter associated with the number of Lost Packets, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

agnClkIntervalOutOfOrderPackets		1.3.6.1.4.1.164.6.2.52.3.2.1.5
The counter associated with the number of times Out-of-Order Packets are detected, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

agnClkIntervalBufferUnderflow		1.3.6.1.4.1.164.6.2.52.3.2.1.6
The counter associated with the number of times Underflow event is detected, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

agnMaxNoOfConns		1.3.6.1.4.1.164.6.2.53
This variable indicates the maximum number of connections that can be configured for the agent.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

lag		1.3.6.1.4.1.164.6.2.54
OBJECT IDENTIFIER

lagTable		1.3.6.1.4.1.164.6.2.54.1
A table defining Link Aggregation Groups port association, and other parameters.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LagEntry

lagEntry		1.3.6.1.4.1.164.6.2.54.1.1
An entry in the LAG table.
Status: current	Access: not-accessible
OBJECT-TYPE
	LagEntry

lagCnfgIdx		1.3.6.1.4.1.164.6.2.54.1.1.1
This object indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..255

lagIdx		1.3.6.1.4.1.164.6.2.54.1.1.2
This object indicates LAG unique index.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

lagPortMembers		1.3.6.1.4.1.164.6.2.54.1.1.3
The set of ports which are permanently assigned to the Link Aggregation Group. The default value of this object is a string of zeros.
Status: current	Access: read-create
OBJECT-TYPE
	PortList

lagDistributionMethod		1.3.6.1.4.1.164.6.2.54.1.1.4
This object defines the criteria for the 802.3ad (LAG) to split the traffic between ports
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	portBased(2), oneToOne(3), sourceMac(4), destinationMac(5), sourceXorDestinationMac(6), sourceAndDestinationMac(7), sourceIp(8), destinationIp(9), sourceAndDestinationMacAndIp(10), roundRobin(11)

lagRecoveryMode		1.3.6.1.4.1.164.6.2.54.1.1.5
This object defines whether traffic will be returned to a port after its recovery. This object is applicable only when lagDistributionMethod= oneToOne (3).
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	nonRevertive(2), revertive(3)

lagWaitToRestore		1.3.6.1.4.1.164.6.2.54.1.1.6
This object defines traffic recovery time (in seconds) to the port after its recovery. This object is applicable only when lagRecoveryMode= revertive (3).
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..720

lagRowStatus		1.3.6.1.4.1.164.6.2.54.1.1.7
This object enables user to create/delete entries of this table. Note: When using LAG standard package, this table is static, hence, only the values active(1), notInService(2) are used.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

lagShutDownDurationUponFlip		1.3.6.1.4.1.164.6.2.54.1.1.8
This object defines the duration (in seconds) the active port transmission is shut down after LAG Flip occurs. The transmission is shut down and then opened again (after the duration defined by this object), in order to cause the other side to flip to the new active port. 0=no shut-down. This object is applicable only when lagDistributionMethod=oneToOne(3) and mainly when each of the Links of our device is connected to a different device.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..30

lagRdnMethod		1.3.6.1.4.1.164.6.2.54.1.1.9
This object defines the redundancy method.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	loadSharing(1), redundancy(2)

lagLacpEnable		1.3.6.1.4.1.164.6.2.54.1.1.10
Enabling/Disabling the LACP for a LAG. The LACP will be enabled for all ports belonging to this LAG.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	no(2), yes(3)

lagStatTable		1.3.6.1.4.1.164.6.2.54.2
A table defining Link Aggregation Groups Redundancy. This table is applicable only when lagDistributionMethod = oneToOne.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LagStatEntry

lagStatEntry		1.3.6.1.4.1.164.6.2.54.2.1
An entry in the LAG Status table.
Status: current	Access: not-accessible
OBJECT-TYPE
	LagStatEntry

lagStatForcePort		1.3.6.1.4.1.164.6.2.54.2.1.1
This object enables user to enforce the active port. 0 = No Enforcement; Otherwise the ifIndex of the port.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

lagStatActivePort		1.3.6.1.4.1.164.6.2.54.2.1.2
This object indicates the current active port. It is applicable only when lagDistributionMethod = oneToOne. The value is the ifIndex of the port. 0 = none of the ports is active.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

gfp		1.3.6.1.4.1.164.6.2.55
OBJECT IDENTIFIER

gfpCnfgTable		1.3.6.1.4.1.164.6.2.55.1
Configuration table for GFP (General Framing Protocol).
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		GfpCnfgEntry

gfpCnfgEntry		1.3.6.1.4.1.164.6.2.55.1.1
An entry in the GFP configuration table.
Status: current	Access: not-accessible
OBJECT-TYPE
	GfpCnfgEntry

gfpCnfgIdx		1.3.6.1.4.1.164.6.2.55.1.1.1
Index to GFP configuration table.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

gfpPayloadFcs		1.3.6.1.4.1.164.6.2.55.1.1.2
This object defines whether protocol header will include FCS.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(2), enable(3)

gfpRxTxScramble		1.3.6.1.4.1.164.6.2.55.1.1.3
This object defines whether transmission will be scrambled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noScramble(1), rxTxScramble(2), rxOnlyScramble(3), txOnlyScramble(4)

gfpVcatHeader		1.3.6.1.4.1.164.6.2.55.1.1.4
VCAT header is LCAS CONTROL packet as described in the G-7043. one control packet is transmitted in a period of 16 Multi frame
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), enable(3)

agnGroupTable		1.3.6.1.4.1.164.6.2.56
A table that enables associating components to Group/s (or removing components of a group). The Group Idx can then be used in other tables (e.g alarmForwardingTable).
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AgnGroupEntry

agnGroupEntry		1.3.6.1.4.1.164.6.2.56.1
An entry in the agnGroupTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	AgnGroupEntry

agnGroupCnfgIdx		1.3.6.1.4.1.164.6.2.56.1.1
This object indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..255

agnGroupIdx		1.3.6.1.4.1.164.6.2.56.1.2
This object indicates a unique Group Index.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

agnGroupComponentIdx		1.3.6.1.4.1.164.6.2.56.1.3
This object indicates a unique Component Index that belongs to the Group defined by agnGroupIdx.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

agnGroupRowStatus		1.3.6.1.4.1.164.6.2.56.1.4
This object enables user to create/delete entries of this table. destroy - If a Group is used in another table, Agent may not allow destroying the entry/ies that belong to this Group Index.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

agnStatNoOfUploadedIntervals		1.3.6.1.4.1.164.6.2.57
This parameter indicates the Number of Intervals that were successfully collected and uploaded in the last statistics collection session.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnSyslog		1.3.6.1.4.1.164.6.2.58
OBJECT IDENTIFIER

agnSyslogDeviceUdpPort		1.3.6.1.4.1.164.6.2.58.1
The UDP Port of the device, from which Syslog messages are sent. Default=514.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

agnSyslogFacility		1.3.6.1.4.1.164.6.2.58.2
A user defined SW module, task or function, from which Syslog messages are sent to the remote Server.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	local1(17), local2(18), local3(19), local4(20), local5(21), local6(22), local7(23)

agnSyslogSeverityLevel		1.3.6.1.4.1.164.6.2.58.3
Device will send events equal or exceeding this severity level (configured by user).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	critical(1), major(2), minor(3), warning(4), event(5), info(6), debug(7)

agnNetworkInterfaceType		1.3.6.1.4.1.164.6.2.59
This MIB object indicates the network interface type to be used by the device. It is used for devices that use only one network port type.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), t1(2), t3(3)

agnTrapDelay		1.3.6.1.4.1.164.6.2.60
This variable enables the user to set a delay (in seconds) before a trap is sent. This delay will be used only for traps that need to be sent during device initialization. It is needed because the device connected to our device starts transmitting traps later. The delay starts from the end of the Boot process. The device will keep the init traps in the correct order, and cancel those which clear former ones in the list. After this init delay, traps will be sent without a delay.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

agnStringToIndexTable		1.3.6.1.4.1.164.6.2.62
This table holds the conversions of tables from unique String to numeric index.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AgnStringToIndexEntry

agnStringToIndexEntry		1.3.6.1.4.1.164.6.2.62.1
An entry in the table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AgnStringToIndexEntry

agnStringToIndexTableId		1.3.6.1.4.1.164.6.2.62.1.1
The OBJECT IDENTIFIER of the Table, having as index numeric values. In this table, the value of agnStringToIndexUserName is an attribute.
Status: current	Access: not-accessible
OBJECT-TYPE
	OBJECT IDENTIFIER

agnStringToIndexUserName		1.3.6.1.4.1.164.6.2.62.1.2
This object indicates a unique name used by agnStringToIndexTableId, although it is not it's index.
Status: current	Access: not-accessible
OBJECT-TYPE
	SnmpAdminString	Size(1..64)

agnStringToIndexTableIndex		1.3.6.1.4.1.164.6.2.62.1.3
The numeric Index of agnStringToIndexTableId.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

agnRowPointerTable		1.3.6.1.4.1.164.6.2.63
This table holds information about a specific entry in a table. For example, number of usages of this row.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AgnRowPointerEntry

agnRowPointerEntry		1.3.6.1.4.1.164.6.2.63.1
An entry in the table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AgnRowPointerEntry

agnRowPointerIndex		1.3.6.1.4.1.164.6.2.63.1.1
The OBJECT IDENTIFIER of an entry in a table.
Status: current	Access: not-accessible
OBJECT-TYPE
	OBJECT IDENTIFIER

agnRowPointerNoOfUsages		1.3.6.1.4.1.164.6.2.63.1.2
The number of usages of specific entry in a table, which is pointed by agnRowPointerIndex.Usually, when the value of this counter is greater than 0,the entry cannot be removed.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

radTransport		1.3.6.1.4.1.164.6.4
OBJECT IDENTIFIER

radTransportDomains		1.3.6.1.4.1.164.6.4.1
OBJECT IDENTIFIER

radTransportDomainSnmpEfmOam		1.3.6.1.4.1.164.6.4.1.1
The SNMP over EFM OAM transport domain. The corresponding transport address is of type RadTransportAddressEfmOam for EFM OAM addresses (port).
Status: current	Access: read-only
OBJECT-IDENTITY

systemsEvents		1.3.6.1.4.1.164.6.1.0
The events for RAD products.
Status: current	Access: read-only
OBJECT-IDENTITY

tftpStatusChangeTrap		1.3.6.1.4.1.164.6.1.0.1
This trap is sent whenever the status of tftp changed.
Status: current	Access: read-only
NOTIFICATION-TYPE

agnStatusChangeTrap		1.3.6.1.4.1.164.6.1.0.2
This trap is sent whenever the state of the entity the agent is responsible for changed. TDM devices will send agnTestStatus variable to indicate the current test status.
Status: current	Access: read-only
NOTIFICATION-TYPE

prtStatusChangeTrap		1.3.6.1.4.1.164.6.1.0.3
This trap is sent whenever the state of a port changed. Attached, will be parameter/s that indicate the new port status. The attached variables will be specified in the specifications of the products supporting this trap.
Status: current	Access: read-only
NOTIFICATION-TYPE

swdlStatusResult		1.3.6.1.4.1.164.6.1.0.4
This notification is sent when Software Down Load is finished. The attached object indicates the File Name.
Status: current	Access: read-only
NOTIFICATION-TYPE

intSwdlSlotFileMismatch		1.3.6.1.4.1.164.6.1.0.5
This notification is sent when the card in the chosen slot doesn't match the chosen file. The attached object indicates the File Name.
Status: current	Access: read-only
NOTIFICATION-TYPE

agnCounterChange		1.3.6.1.4.1.164.6.1.0.6
This notification is sent when the value of a specific Counter is changed. Agent can send as attached object the updated Counter. For details about this Counter and attached object, see spec of the relevant application.
Status: current	Access: read-only
NOTIFICATION-TYPE

prtClkSrcChangeTrap		1.3.6.1.4.1.164.6.1.0.7
This trap is sent upon any port clock change.
Status: current	Access: read-only
NOTIFICATION-TYPE

moduleFailTrap		1.3.6.1.4.1.164.6.1.0.8
This trap is sent upon a module failure.
Status: current	Access: read-only
NOTIFICATION-TYPE

moduleInitFailTrap		1.3.6.1.4.1.164.6.1.0.9
This trap is sent upon a module initialization failure.
Status: current	Access: read-only
NOTIFICATION-TYPE

clkSrcChangeTrap		1.3.6.1.4.1.164.6.1.0.10
This trap is sent upon any change in Clock Source.
Status: current	Access: read-only
NOTIFICATION-TYPE

agnUploadDataTrap		1.3.6.1.4.1.164.6.1.0.11
This trap is sent upon an upload data session termination. For more details see product specification.
Status: current	Access: read-only
NOTIFICATION-TYPE

enrollmentTrap		1.3.6.1.4.1.164.6.1.0.12
This trap is a periodically trap, which sent to manager untill Agent get any response (Get or Set) from this manager.
Status: current	Access: read-only
NOTIFICATION-TYPE

agnPowerFailureTrap		1.3.6.1.4.1.164.6.1.0.13
This trap is sent upon power failure. It is applicable for the following devices: 1. Devices having one PS unit, which sense the failure in advance, and still have time to send this trap before it goes off. 2. Devices having 2 PS units and send this trap in order to notify a failure in one of the units.
Status: current	Access: read-only
NOTIFICATION-TYPE

agnFanFailureTrap		1.3.6.1.4.1.164.6.1.0.14
This trap is sent upon fan failure/recovery.
Status: current	Access: read-only
NOTIFICATION-TYPE

agnSystemParameterChangeTrap		1.3.6.1.4.1.164.6.1.0.15
This trap is sent upon any change of the systemParameter value.
Status: current	Access: read-only
NOTIFICATION-TYPE

agnConfigDBChecksumError		1.3.6.1.4.1.164.6.1.0.16
This trap indicates that the database currently stored in the non-volatile memory of the device is corrupted
Status: current	Access: read-only
NOTIFICATION-TYPE

agnAlarmBufferOverflow		1.3.6.1.4.1.164.6.1.0.17
This trap indicates that the quantity of alarm messages which have been written in the alarm buffer, since the last clear command, exceeds predefined threshold. (Buffer size) The new alarms are overwriting the oldest alarms (the first alarms written in the buffer). For LA-110,threshold value is 200 alarms.
Status: current	Access: read-only
NOTIFICATION-TYPE

agnAlarmBufferClear		1.3.6.1.4.1.164.6.1.0.18
This trap indicates that alarm buffer has been cleared.
Status: current	Access: read-only
NOTIFICATION-TYPE

agnParametersValueChanged		1.3.6.1.4.1.164.6.1.0.19
This trap indicates that due to software upgrade, some of the parameters are assigned new values
Status: current	Access: read-only
NOTIFICATION-TYPE

agnDriverSwMismatch		1.3.6.1.4.1.164.6.1.0.20
There is mismatch between the SW driver and the HW of the device uplink interface.
Status: current	Access: read-only
NOTIFICATION-TYPE

agnActualLowRate		1.3.6.1.4.1.164.6.1.0.21
The main link is synchronized at a rate lower than expected.
Status: current	Access: read-only
NOTIFICATION-TYPE

xModemFileTransferStatusTrap		1.3.6.1.4.1.164.6.1.0.22
This trap is sent in the following cases: - When an xModem File Transfer Session begins. In this case, the trapVal.1 string sent will be: 'Start'. - When an xModem File Transfer Session ends. In this case, the trapVal.1 string sent will be one of the following, according to the way the session ended : - 'End: OK' - 'End: Failed'
Status: current	Access: read-only
NOTIFICATION-TYPE

agnStationClkFailureTrap		1.3.6.1.4.1.164.6.1.0.23
This trap is sent upon Station Clock failure.
Status: current	Access: read-only
NOTIFICATION-TYPE

successfulLogin		1.3.6.1.4.1.164.6.1.0.24
This trap is sent when a user performed successful Login via Terminal/Telnet/Web. This trap is used when the device is located at End-User's premises while management is at Service Provider's premises.
Status: current	Access: read-only
NOTIFICATION-TYPE

failedLogin		1.3.6.1.4.1.164.6.1.0.25
This trap is sent when a user tried to Login via Terminal/Telnet/Web and failed. This trap is used when the device is located at End-User's premises while management is at Service Provider's premises.
Status: current	Access: read-only
NOTIFICATION-TYPE

modlChangeTrap		1.3.6.1.4.1.164.6.1.0.26
This trap is sent whenever a module is inserted or removed. The trap should include the new module type (e.g. modlParamType).
Status: current	Access: read-only
NOTIFICATION-TYPE

licenseUpdateTrap		1.3.6.1.4.1.164.6.1.0.27
This trap is sent whenever a license is successfully downloaded or whenever a license's demo duration is expired.
Status: current	Access: read-only
NOTIFICATION-TYPE

agnClkSrcStateChangeTrap		1.3.6.1.4.1.164.6.1.0.28
The trap is sent upon change in Recovery Clock State.
Status: current	Access: read-only
NOTIFICATION-TYPE

agnSelfTestResultChangeTrap		1.3.6.1.4.1.164.6.1.0.29
The trap is sent upon each change in the result of a Self State operation.
Status: current	Access: read-only
NOTIFICATION-TYPE

agnClkSrcFrequencyAlarmTrap		1.3.6.1.4.1.164.6.1.0.31
The trap is sent upon Recovered Clock Frequency alarm.
Status: current	Access: read-only
NOTIFICATION-TYPE

genBridge		1.3.6.1.4.1.164.4.1
OBJECT IDENTIFIER

radBridgeAction		1.3.6.1.4.1.164.4.1.1
This variable enables the operator to perform one of the specified actions on the tables maintained by the network device. Send actions are not currently implemented. Not all actions can be performed on all bridges.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	reset(1), sendNetworkTab(2), deleteNetworkTab(3), sendRoutingTab(4), deleteRoutinTab(5), sendLanTab(6), deleteLanTab(7), deleteArpTab(8), sendArpTab(9), deleteRouteTab(10), sendRouteTab(11), deactivateAllMasks(12), saveAllActiveMasks(13), loadAndActivateAllMasksFromNVRAM(14), clearAllMasksFromNVRAM(15), defaultConfig(16), resetNVRAM(17), clearIPNVRAM(18), noOp(255)

radBridgeInactiveArpTimeOut		1.3.6.1.4.1.164.4.1.2
This variable defines the maximum time period that can pass between ARP requests concerning an entry in the ARP table. After this time period, the entry is deleted from the table.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

radBridgeMaskTable		1.3.6.1.4.1.164.4.1.3
Mask tables enable definition of forwarding restrictions and control of message flow in the internetwork. Each entry in this table defines a mask statement consisting of up to three mask definitions and an action defined by radBridgeMaskOper. Different types of mask entries are supported, as defined by radBridgeMaskType.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RadBridgeMaskEntry

radBridgeMaskEntry		1.3.6.1.4.1.164.4.1.3.1
An entry in table radBridgeMaskTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	RadBridgeMaskEntry

radBridgeMaskType		1.3.6.1.4.1.164.4.1.3.1.1
Defines the type of mask entry.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	tx(1), rx(2), compress(3), priority(4), loadSharing(5), facs(6), codConnect(7), codDisconnect(8)

radBridgeMaskIfIndex		1.3.6.1.4.1.164.4.1.3.1.2
Specifies the if Index of the interface to which the mask is applied.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

radBridgeMaskNum		1.3.6.1.4.1.164.4.1.3.1.3
The Mask entry number, defined by its line number in the mask table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

radBridgeMaskDest		1.3.6.1.4.1.164.4.1.3.1.4
Specifies the type of destination address carried by the frame to which the mask will be applied. Unassigned-condition deactivates the mask entry.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unassigned-cond(1), broadcast-msge(2), multicast-msge(3), all-msge(4), none(5)

radBridgeMaskPat1		1.3.6.1.4.1.164.4.1.3.1.5
Describes the mask field which is either a 16 bit binary pattern, or four digit hexadecimal pattern.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

radBridgeMaskActiveBit1		1.3.6.1.4.1.164.4.1.3.1.6
Specifies the positions of the wild card characters (*) in the radBridgeMaskPat1 field.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

radBridgeMaskFrom1		1.3.6.1.4.1.164.4.1.3.1.7
Offset base of radBridgeMaskPat1 within the frame. Net can be in some cases the data start point.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	mac(1), llc(2), net(3)

radBridgeMaskOffset1		1.3.6.1.4.1.164.4.1.3.1.8
Specifies the radBridgeMaskPat1 offset within the frame (in bytes) from the base defined in by radBridgeMaskForm1.The mask offset is an even decimal number in the range of 0 to 1518.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

radBridgeMaskCond1		1.3.6.1.4.1.164.4.1.3.1.9
Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by radBridgeMaskOffset1 the packet contains data that matches the content of radBridgeMaskPat1. false - Condition is valid if at the position specified by radBridgeMaskOffset1 the packet contains data that does not match the content of radBridgeMaskPat1.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	false(1), true(2)

radBridgeMaskPat2		1.3.6.1.4.1.164.4.1.3.1.10
Describes the mask field which is either a 16 bit binary pattern, or four digit hexadecimal pattern.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

radBridgeMaskActiveBit2		1.3.6.1.4.1.164.4.1.3.1.11
Specifies the positions of the wild card characters (*) in the radBridgeMaskPat2 field.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

radBridgeMaskFrom2		1.3.6.1.4.1.164.4.1.3.1.12
Offset base of radBridgeMaskPat2 within the frame. Net can be in some cases the data start point.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	mac(1), llc(2), net(3)

radBridgeMaskOffset2		1.3.6.1.4.1.164.4.1.3.1.13
Specifies the radBridgeMaskPat2 offset within the frame (in bytes) from the base defined in by radBridgeMaskForm2.The mask offset is an even decimal number in the range of 0 to 1518.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

radBridgeMaskCond2		1.3.6.1.4.1.164.4.1.3.1.14
Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by radBridgeMaskOffset2 the packet contains data that matches the content of radBridgeMaskPat2. false - Condition is valid if at the position specified by radBridgeMaskOffset2 the packet contains data that does not match the content of radBridgeMaskPat2.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	false(1), true(2)

radBridgeMaskPat3		1.3.6.1.4.1.164.4.1.3.1.15
Describes the mask field which is either a 16 bit binary pattern, or four digit hexadecimal pattern.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

radBridgeMaskActiveBit3		1.3.6.1.4.1.164.4.1.3.1.16
Specifies the positions of the wild card characters (*) in the radBridgeMaskPat3 field.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

radBridgeMaskFrom3		1.3.6.1.4.1.164.4.1.3.1.17
Offset base of radBridgeMaskPat3 within the frame. Net can be in some cases the data start point.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	mac(1), llc(2), net(3)

radBridgeMaskOffset3		1.3.6.1.4.1.164.4.1.3.1.18
Specifies the radBridgeMaskPat3 offset within the frame (in bytes) from the base defined in by radBridgeMaskForm3. The mask offset is an even decimal number in the range of 0 to 1518.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

radBridgeMaskCond3		1.3.6.1.4.1.164.4.1.3.1.19
Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by radBridgeMaskOffset3 the packet contains data that matches the content of radBridgeMaskPat3 false - Condition is valid if at the position specified by radBridgeMaskOffset3 the packet contains data that does not match the content of radBridgeMaskPat3.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	false(1), true(2)

radBridgeMaskOper		1.3.6.1.4.1.164.4.1.3.1.20
The type of action to be taken if the frame meets the conditions of the mask. noOp = disabled (mask remains on list, but is not active) delete = mask is removed from the list.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	block(1), forward(2), route(3), forward-route(4), high-priority(5), noOp(6), delete(7)

radBridgeCOD		1.3.6.1.4.1.164.4.1.4
OBJECT IDENTIFIER

radBridgeCODParamTable		1.3.6.1.4.1.164.4.1.4.1
The table of COD parameters
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RadBridgeCODEntry

radBridgeCODEntry		1.3.6.1.4.1.164.4.1.4.1.1
Each radBridgeCODEntry consists of the following parameters
Status: current	Access: not-accessible
OBJECT-TYPE
	RadBridgeCODEntry

radBridgeCODIfIndex		1.3.6.1.4.1.164.4.1.4.1.1.1
The interface to which this COD entry is applicable.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

radBridgeCODManualConnect		1.3.6.1.4.1.164.4.1.4.1.1.2
The management station can start connection manually by setting this parameter
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	connect(1), disconnect(2)

radBridgeCODMode		1.3.6.1.4.1.164.4.1.4.1.1.3
In answer mode only one incoming call may be accepted at a time. Other nodes attempting to access the local modem will receive a busy signal until the connection is terminated. (Answer mode has no difficulty supporting multiple remote connections to one local port, as blocking multiple incoming calls is just a modem function. Originate mode, on the other hand will only support a single local port to remote port connection). The disable parameter disables the COD utility for this interface. Choosing any other mode will enable the COD utility.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	answer(1), originate(2), disable(3), answerAndOriginate(4)

radBridgeCODConnectDelay		1.3.6.1.4.1.164.4.1.4.1.1.4
The connect delay defines the minimum time period that the link must stay disconnected, between 2 succesive connections (in seconds).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

radBridgeCODisConnectDelay		1.3.6.1.4.1.164.4.1.4.1.1.5
The disconnect delay defines the minimum time period the link must stay connected, between 2 succesive disconnections (in seconds).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

radBridgeCODImplicitSwitch		1.3.6.1.4.1.164.4.1.4.1.1.6
The inplicit switch allows the user to ignore implicit triggers provided by the COD software.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

radBridgeCODNumAccess		1.3.6.1.4.1.164.4.1.4.1.1.7
The number of successful connections that have been established since the COD has been reset.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

radBridgeCODTotalConnecTime		1.3.6.1.4.1.164.4.1.4.1.1.8
The sum of all the connect time intervals since the COD was reset.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

radBridgeCODTimeTriggerTable		1.3.6.1.4.1.164.4.1.4.2
The table of COD parameters
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RadBridgeCODTimeTriggerEntry

radBridgeCODTimeTriggerEntry		1.3.6.1.4.1.164.4.1.4.2.1
Each radBridgeCODTimeTriggerEntry consists of the following parameters
Status: current	Access: not-accessible
OBJECT-TYPE
	RadBridgeCODTimeTriggerEntry

radBridgeCODTimeIfIndex		1.3.6.1.4.1.164.4.1.4.2.1.1
The interface to which this COD Time Trigger entry is applicable.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

radBridgeCODDay		1.3.6.1.4.1.164.4.1.4.2.1.2
The day of the week in which the dial up connection operates.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	mon(1), tue(2), wed(3), thu(4), fri(5), sat(6), sun(7)

radBridgeCODTimeTriggerNum		1.3.6.1.4.1.164.4.1.4.2.1.3
Every day of the week the user can configure 3 dial up connections.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..3

radBridgeCODTimeTriggerFrom		1.3.6.1.4.1.164.4.1.4.2.1.4
Time to start Dial Up connection, in format hh:mm.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

radBridgeCODTimeTriggerTo		1.3.6.1.4.1.164.4.1.4.2.1.5
Time to terminate Dial Up connection, in format HH:MM.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

radBridgeCODTimeTriggerStatus		1.3.6.1.4.1.164.4.1.4.2.1.6
The status of a table entry.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	valid(1), invalid(2)

radBridgeCODTraffic		1.3.6.1.4.1.164.4.1.4.3
OBJECT IDENTIFIER

radBridgeCODTrafficTable		1.3.6.1.4.1.164.4.1.4.3.1
The table of COD Traffic trigger
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RadBridgeCODTrafficEntry

radBridgeCODTrafficEntry		1.3.6.1.4.1.164.4.1.4.3.1.1
Each radBridgeCODTrafficEntry consists of the following parameters.
Status: current	Access: not-accessible
OBJECT-TYPE
	RadBridgeCODTrafficEntry

radBridgeCODProtocolType		1.3.6.1.4.1.164.4.1.4.3.1.1.1
The Protocol Type of the Traffic Table
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ip(1), ipx(2), other(3)

radBridgeCODTrafficTriggerStatus		1.3.6.1.4.1.164.4.1.4.3.1.1.2
Command of Status of the Protocol Traffic Trigger
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

radBridgeCODRemoteIPAddr		1.3.6.1.4.1.164.4.1.4.3.2
This is the Remote IP Address
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

radBridgeCODIPMask		1.3.6.1.4.1.164.4.1.4.3.3
This is the Mask of the Remote IP Address
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

radBridgeCODTrafficTriggerProtType		1.3.6.1.4.1.164.4.1.4.3.4
Protocol Type for the User Defined Protocol Traffic Trigger (3).
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

radBridgeCODCondTable		1.3.6.1.4.1.164.4.1.4.4
The table of COD Condition parameters
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RadBridgeCODCondEntry

radBridgeCODCondEntry		1.3.6.1.4.1.164.4.1.4.4.1
Each radBridgeCODCondEntry consists of the following parameters
Status: current	Access: not-accessible
OBJECT-TYPE
	RadBridgeCODCondEntry

radBridgeCODCondIfIndex		1.3.6.1.4.1.164.4.1.4.4.1.1
The interface, this COD entry is applicable to.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

radBridgeCODOriginateConnectCondition		1.3.6.1.4.1.164.4.1.4.4.1.2
This condition, allows the user to specify the condition under which the link is connected. The options are onPowerOn - On power on. whenAnyStationOnLan - When any station on lan. onTraffic - On traffic. The user can specify the condition/s for connection. The connection will be defined in CODSpecificOnTrafficConditionOID . onManualConnect - depends on radBridgeCODManualConnect OBJECT-TYPE (=connect).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	onPowerOn(1), whenAnyStationOnLan(2), onTraffic(3), onManualConnect(4)

radBridgeCODOriginateDisConnectCondition		1.3.6.1.4.1.164.4.1.4.4.1.3
This condition allows the user to specify the condition under which the link is disconnected. The options are: noStationOnLan - When there is no station on lan. Counts 15 minutes from the point the last frame from lan has been received. If no frame have been transmitted on lan by the end of this period, disconnect the connection. onTraffic - On traffic. The user can specify the condition/s for disconnection. The disconnection will be defined in CODSpecificOnTrafficConditionOID . onDelayFromConnectionOnRequest - On Delay From Connection On Request . The delay time period will be defined in CODOriginateDisConnectDelay . onManualDisConnect - depends on radBridgeCODManualConnect OBJECT-TYPE (=disconnect).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noStationOnLan(1), onTraffic(2), onDelayFromConnectionOnRequest(3), onManualDisConnect(4)

radBridgeCODOriginateDisConnectDelay		1.3.6.1.4.1.164.4.1.4.4.1.4
Delay time in seconds.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

radBridgeCODAnswerConnectCondition		1.3.6.1.4.1.164.4.1.4.4.1.5
CODCondAnswerConnect allows the user to specify the condition under which the link is connected. The options are: onPowerOn - On power on. whenAnyStationOnLan - When any station on lan. onTraffic - On traffic. The user can specify the condition/s for connection. The connection will be defined in CODSpecificOnTrafficConditionOID . onManualConnect - depends on radBridgeCODManualConnect OBJECT-TYPE .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	onPowerOn(1), whenAnyStationOnLan(2), onTraffic(3), onManualConnect(4)

radBridgeCODSpecificOnTrafficOIDCondition		1.3.6.1.4.1.164.4.1.4.4.1.6
A reference to a specific entry in the radBridgeMaskTable, which describes the particular COD condition . If Connect or Disconnect Conditions are not onTraffic, its value should be set to the OBJECT IDENTIFIER { 0 0 }.
Status: current	Access: read-only
OBJECT-TYPE
	OBJECT IDENTIFIER

radBridgeCODDisConnectMinimunFramesNumber		1.3.6.1.4.1.164.4.1.4.4.1.7
Frames rate.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

radBridgeIPX		1.3.6.1.4.1.164.4.1.5
OBJECT IDENTIFIER

radBridgeIPXdriver		1.3.6.1.4.1.164.4.1.5.1
OBJECT IDENTIFIER

radBridgeIPXRip		1.3.6.1.4.1.164.4.1.5.2
OBJECT IDENTIFIER

radBridgeIPXSap		1.3.6.1.4.1.164.4.1.5.3
OBJECT IDENTIFIER

radBridgeIPXForwarding		1.3.6.1.4.1.164.4.1.5.1.1
The indication of whether this entity is acting as an IPX gateway in respect to the forwarding of datagrams received by, but not addressed to, this entity. IPX gateways forward datagrams. IPX hosts do not. Note that changing this parameter requiers RESET of the router.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	forwarding(1), not-forwarding(2)

radBridgeIPXRipOutPackets		1.3.6.1.4.1.164.4.1.5.2.1
The total number of packets transmitted by RIP.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

radBridgeIPXRipInPackets		1.3.6.1.4.1.164.4.1.5.2.2
The total number of packets received by RIP. This will include any packets that are subsequently discarded.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

radBridgeIPXRipInDiscards		1.3.6.1.4.1.164.4.1.5.2.3
The number of received packets discarded by RIP.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

radBridgeIPXRipTblNoOfEntries		1.3.6.1.4.1.164.4.1.5.2.4
The max number of entries that exist in the RIP routing table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

radBridgeIPXRipTblBcastTrigUpdateInterval		1.3.6.1.4.1.164.4.1.5.2.5
The default time interval (in seconds)between triggered RIP updates on a broadcast type interface. A triggered update occurs when a change is detected in the routing database. This time interval delays the broadcasting of these updates so that changes on the network will not result in a lot of triggered updates.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

radBridgeIPXRipTable		1.3.6.1.4.1.164.4.1.5.2.6
The routing table used by RIP to calculate routes to remote desination networks.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RadBridgeIPXRipTableEntry

radBridgeIPXRipTableEntry		1.3.6.1.4.1.164.4.1.5.2.6.1
The routing information for one of this entity's destination networks.
Status: current	Access: not-accessible
OBJECT-TYPE
	RadBridgeIPXRipTableEntry

radBridgeIPXRipDestNetwork		1.3.6.1.4.1.164.4.1.5.2.6.1.1
The destination network address to which this entry's routing information pertains.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(4)

radBridgeIPXRipPolicy		1.3.6.1.4.1.164.4.1.5.2.6.1.2
A value specifying the precidence of the route. A value of zero means that the route is the best route, a value of one means that the route is the second best route and so on.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	main(1), alternate(2)

radBridgeIPXRipForwardingRouter		1.3.6.1.4.1.164.4.1.5.2.6.1.3
The IPX node address of the next hop (router) for the entry's associated destination network.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(6)

radBridgeIPXRipNIC		1.3.6.1.4.1.164.4.1.5.2.6.1.4
An interface identifier specifying what IPX interface the next hop can be found on.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

radBridgeIPXRipTickMetric		1.3.6.1.4.1.164.4.1.5.2.6.1.5
The metric, in terms of transit time, associated with the route given by the entry. This time is in terms of 1/18ths of a second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

radBridgeIPXRipHopMetric		1.3.6.1.4.1.164.4.1.5.2.6.1.6
The metric, in terms of distance , associated with the route given by the entry.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

radBridgeIPXRipAgingTime		1.3.6.1.4.1.164.4.1.5.2.6.1.7
The last time that the entry was updated. The time will be provided in terms of the MIB-I object sysUpTime.
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

radBridgeIPXRipValueStatus		1.3.6.1.4.1.164.4.1.5.2.6.1.8
The entry status value; whether the entry is permanent (added statically), reachable or unreachable. In the latter two cases it would be added by RIP. A semiDynamic entry is an entry enterd manualy by the user and can be updated by the router.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	static(1), dynamic(2), invalid(3), semiDynamic(4)

radBridgeIPXRipForwardType		1.3.6.1.4.1.164.4.1.5.2.6.1.9
The type of route. Note that local(2) refers to a route for which the next hop is the final destination; remote(3) refers to a route for which the next hop is not the final destination.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), local(2), remote(3)

radBridgeIPXRipInfTable		1.3.6.1.4.1.164.4.1.5.2.7
The RIP interface table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RadBridgeIPXRipInfEntry

radBridgeIPXRipInfEntry		1.3.6.1.4.1.164.4.1.5.2.7.1
Each entry corresponds to one ifindex.
Status: current	Access: not-accessible
OBJECT-TYPE
	RadBridgeIPXRipInfEntry

radBridgeIPXRipInfIfIndex		1.3.6.1.4.1.164.4.1.5.2.7.1.1
This value of Ifindex is same as radBridgeIPXIfIndex in the IPX Interface Table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

radBridgeIPXRipInfBcastUpdate		1.3.6.1.4.1.164.4.1.5.2.7.1.2
The RIP periodic update interval, in seconds. Zero value corresponds to infinite interval.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

radBridgeIPXRipInfAgeMultiplier		1.3.6.1.4.1.164.4.1.5.2.7.1.3
The holding multiplier for information received in RIP periodic updates. Zero value corresponds to infinite aging time.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

radBridgeIPXSapOutPackets		1.3.6.1.4.1.164.4.1.5.3.1
The total number of packets transmitted by SAP.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

radBridgeIPXSapInPackets		1.3.6.1.4.1.164.4.1.5.3.2
The total number of packets received by SAP. This will include any packets that are subsequently discarded.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

radBridgeIPXSapInDiscards		1.3.6.1.4.1.164.4.1.5.3.3
The number of received packets discarded by SAP.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

radBridgeIPXSapTblNoOfEntries		1.3.6.1.4.1.164.4.1.5.3.4
The max number of entries that exist in the SAP Server Information table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

radBridgeIPXSapTblBcastTrigUpdateInterval		1.3.6.1.4.1.164.4.1.5.3.5
The default time interval (in seconds) between triggered SAP updates on a broadcast style interface. A triggered update occurs when a change is detected in the service database. This time interval delays the transmission of these updates so that changes on the network will not result in a lot of triggered updates.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

radBridgeIPXSapTable		1.3.6.1.4.1.164.4.1.5.3.6
The Server Information table is used by SAP to store information of services which are available on the internetwork.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RadBridgeIPXSapTableEntry

radBridgeIPXSapTableEntry		1.3.6.1.4.1.164.4.1.5.3.6.1
The server information for one of this entity's server entries.
Status: current	Access: not-accessible
OBJECT-TYPE
	RadBridgeIPXSapTableEntry

radBridgeIPXSapServerType		1.3.6.1.4.1.164.4.1.5.3.6.1.1
The type of the server for which this entry pertains.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

radBridgeIPXSapName		1.3.6.1.4.1.164.4.1.5.3.6.1.2
The name of the server for which this entry pertains.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(48)

radBridgeIPXSapNetwork		1.3.6.1.4.1.164.4.1.5.3.6.1.3
The IPX network address of the host on which this server exists.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(4)

radBridgeIPXSapNode		1.3.6.1.4.1.164.4.1.5.3.6.1.4
The IPX node address of the host on which this server exists.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(6)

radBridgeIPXSapSocket		1.3.6.1.4.1.164.4.1.5.3.6.1.5
The IPX socket number that is being used by the server to which this entry pertains.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

radBridgeIPXSapHopsToServer		1.3.6.1.4.1.164.4.1.5.3.6.1.6
The number of hops to the entity on which this server exists.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..16

radBridgeIPXSapNIC		1.3.6.1.4.1.164.4.1.5.3.6.1.7
An Network Interface Card identifier specifying what IPX interface the next hop can be found on.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

radBridgeIPXSapAgingTime		1.3.6.1.4.1.164.4.1.5.3.6.1.8
The last time that the entry was updated. The time will be provided in terms of the MIB-I object sysUpTime.
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

radBridgeIPXSapStatus		1.3.6.1.4.1.164.4.1.5.3.6.1.9
The status of the entry.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	permanent(1), dynamic(2), invalid(3), semiDynamic(4)

radBridgeIPXSapInfTable		1.3.6.1.4.1.164.4.1.5.3.7
The Sap interface table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RadBridgeIPXSapInfEntry

radBridgeIPXSapInfEntry		1.3.6.1.4.1.164.4.1.5.3.7.1
Each entry corresponds to one ifindex.
Status: current	Access: not-accessible
OBJECT-TYPE
	RadBridgeIPXSapInfEntry

radBridgeIPXSapInfIfIndex		1.3.6.1.4.1.164.4.1.5.3.7.1.1
This value of Ifindex is same as radBridgeIPXIfIndex in the IPX Interface Table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

radBridgeIPXSapInfBcastUpdate		1.3.6.1.4.1.164.4.1.5.3.7.1.2
The SAP periodic update interval, in seconds. Zero value corresponds to infinite interval.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

radBridgeIPXSapInfAgeMultiplier		1.3.6.1.4.1.164.4.1.5.3.7.1.3
The holding multiplier for information received in SAP periodic updates. Zero value corresponds to infinite aging time.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

newMasking		1.3.6.1.4.1.164.4.1.6
OBJECT IDENTIFIER

maskingMaxEntries		1.3.6.1.4.1.164.4.1.6.1
The maximum number of entries in the masking table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

maskingCurrentEntries		1.3.6.1.4.1.164.4.1.6.2
The number of entries in the mask table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

maskingTable		1.3.6.1.4.1.164.4.1.6.3
This is the new masking scheme. Mask tables enable definition of forwarding restrictions and control of message flow in the internetwork. Each entry in this table defines a mask statement and an action defined by maskingOperation.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MaskingEntry

maskingEntry		1.3.6.1.4.1.164.4.1.6.3.1
Defines the contents of each line in the mask table.
Status: current	Access: not-accessible
OBJECT-TYPE
	MaskingEntry

maskingType		1.3.6.1.4.1.164.4.1.6.3.1.1
Defines the type of mask entry.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	tx(1), rx(2), compress(3), priority(4), loadSharing(5), facs(6), codConnect(7), codDisconnect(8)

maskingIfIndex		1.3.6.1.4.1.164.4.1.6.3.1.2
Specifies the ifIndex of the interface to which the mask is applied.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

maskingIndex		1.3.6.1.4.1.164.4.1.6.3.1.3
An index to the masking table. This number should not be greater than maskingMaxEntries
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

maskingProtocolType		1.3.6.1.4.1.164.4.1.6.3.1.4
The base protocol for masking. IPX, IP, others.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unknown(1), ip(2), ipx(3), sna(4), netbios(5), apple(6), dec(7), all(255)

maskingSmartMaskOID		1.3.6.1.4.1.164.4.1.6.3.1.5
A reference to a specific Smart mask table (old radBridgeMaskTable) which enables a more specific mask type. If this information is not available, its value should be set to the OBJECT IDENTIFIER { 0 0 }.
Status: current	Access: read-only
OBJECT-TYPE
	OBJECT IDENTIFIER

maskingFrameType		1.3.6.1.4.1.164.4.1.6.3.1.6
Enables the user to decide about frame type * all frame * just broadcast * just multicast.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unknown(1), all(2), broadcast(3), multicast(4)

maskingFrameTypeCondition		1.3.6.1.4.1.164.4.1.6.3.1.7
Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by maskingFrameType the packet contains data that matches the content of maskingFrameType. fa lse - Condition is valid if at the position specified by maskingFrameType the packet contains data that does not match the content of maskingFrameType.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	false(1), true(2)

maskingSourceAddress		1.3.6.1.4.1.164.4.1.6.3.1.8
The source address is according to the maskingMacOrNet and maskingProtocolType variables. In case of 'MAC' enter 6 bytes (48 bit) of source address. In case of 'NET' if the maskingProtocolType is IP, this is the IP address if the maskingProtocolType is IPX, this is the IPX address (nnnnmmmmmmss) nnnn - IPX net address mmmmmm - Node address (Mac) ss - IPX socket In case of 'Apple' nn - net address (4 nibbles) ss - socket (4 nibbles).
Status: current	Access: read-write
OBJECT-TYPE
	GenAddress

maskingSourceActiveBits		1.3.6.1.4.1.164.4.1.6.3.1.9
Specifies the positions of the wild card characters (*) in the maskingSourceAddress field. Only the 1's bit will be taken in considerations.
Status: current	Access: read-write
OBJECT-TYPE
	GenAddress

maskingSourceMacOrNet		1.3.6.1.4.1.164.4.1.6.3.1.10
The variable maskingSourceAddress and maskingSourceActiveBits will be treated as MAC, or NET address. - If maskingProtocolType = 'all', 'sna', 'netbios', dec or 'unknown', the maskingSourceMacOrNet can be macAddress only! - If maskingProtocolType = 'ip' the maskingSourceMacOrNet can be macAddress or netAddress or appleAddress. - If maskingProtocolType = 'ipx', the maskingSourceMacOrNet can be either macAddress or netAddress. - If maskingProtocolType = 'apple', the maskingSourceMacOrNet can be either macAddress or appleAddress.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	macAddress(1), netAddress(2), ipRange(3), appleAddress(4)

maskingSourceCondition		1.3.6.1.4.1.164.4.1.6.3.1.11
Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by maskingSourceAddress (in conjunction with maskingSourceActiveBits) the packet contains data that matches the content of maskingSourceAddress. false - Condition is valid if at the position specified by maskingSourceAddress (in conjunction with maskingSourceActiveBits) the packet contains data that does not match the content of maskingSourceAddress.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	false(1), true(2)

maskingDestAddress		1.3.6.1.4.1.164.4.1.6.3.1.12
If maskingFrameType = broadcast or multicast, this object is NOT APPLICABLE. If maskingFrameType = all or unknown, this object is applicable. The destination address is according to the maskingMacOrNet and maskingProtocolType variables. In case of 'MAC' enter 6 bytes (48 bit) of source address. In case of 'NET' if the maskingProtocolType is IP, this is the IP address if the maskingProtocolType is IPX, this is the IPX address (nnnnmmmmmmss) nnnn - IPX net address mmmmmm - Node address (Mac) ss - IPX socket. In case of 'Apple' nn - net address (4 nibbles) ss - socket (4 nibbles). The IPX socket entered here has priority over the value of maskingLowLevelProt, when it is ipxRip, ipxSap or ipxSpx, unless the entered IPX socket is don't care.
Status: current	Access: read-write
OBJECT-TYPE
	GenAddress

maskingDestActiveBits		1.3.6.1.4.1.164.4.1.6.3.1.13
If maskingFrameType = broadcast or multicast, this object is NOT APPLICABLE. If maskingFrameType = all or unknown, this object is applicable. Specifies the positions of the wild card characters (*) in the maskingDestAddress field. Only the 1's bit will be taken in considerations.
Status: current	Access: read-write
OBJECT-TYPE
	GenAddress

maskingDestMacOrNet		1.3.6.1.4.1.164.4.1.6.3.1.14
If maskingFrameType = broadcast or multicast, this object is NOT APPLICABLE. If maskingFrameType = all or unknown, this object is applicable. - If maskingProtocolType = 'all', 'sna', 'netbios', dec or 'unknown', the maskingDestMacOrNet can be macAddress only! - If maskingProtocolType = 'ip' the maskingDestMacOrNet can be macAddress or netAddress or appleAddress. - If maskingProtocolType = 'ipx', the maskingDestMacOrNet can be either macAddress or netAddress. - If maskingProtocolType = 'apple', the maskingDestMacOrNet can be either macAddress or appleAddress. The variable maskingDestAddress and maskingDestActiveBits will be treated as MAC, or NET address.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	macAddress(1), netAddress(2), ipRange(3), appleAddress(4)

maskingDestCondition		1.3.6.1.4.1.164.4.1.6.3.1.15
If maskingFrameType = broadcast or multicast, this object is NOT APPLICABLE. If maskingFrameType = all or unknown, this object is applicable. Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by maskingDestAddress (in conjunction with maskingDestActiveBits) the packet contains data that matches the content of maskingDestAddress. false - Condition is valid if at the position specified by maskingDestAddress (in conjunction with maskingDestActiveBits) the packet contains data that does not match the content of maskingDestAddress.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	false(1), true(2)

maskingLowLevelProt		1.3.6.1.4.1.164.4.1.6.3.1.16
This field is set in conjunction with the maskingProtocolType variable. This variable specifies the low level protocol. The IPX socket entered in maskingDestAddress has priority over the value of maskingLowLevelProt, when it is ipxRip, ipxSap or ipxSpx, unless the entered IPX socket is don't care.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unknown(1), ipxRip(2), ipxSap(3), ipxSpx(4), ipUdp(5), ipTcp(6), ipIcmp(7), ipxNcp(8), ipxWan(9), ipxEco(10), ipxErr(11), ipxPep(12)

maskingLowLevelProtCondition		1.3.6.1.4.1.164.4.1.6.3.1.17
Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by maskingLowLevelProt the packet contains data that matches the content of maskingLowLevelProt. false - Condition is valid if at the position specified by maskingLowLevelProt the packet contains data that does not match the content of maskingLowLevelProt.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	false(1), true(2)

maskingHighLevelProt		1.3.6.1.4.1.164.4.1.6.3.1.18
This field is set in connection to the maskingProtocolType variable. This variable specifies the high level protocols (application). As for today it supports just IP protocol stack. The object's value is a sum of the following instances values (selected by user): none (0), -- don't care ftp (1), ftpC (2), telnet (4), smtp (8), tftp (16), snmp (32), snmpTrap (64), ipRip (128), www (256), email (512), dns (1024), For Apple Protocol only: rtmp (2048), nbp (4096), atp (8192), aep (16384), zip (32768), adsp (65536), pap (131072), asp (262144) Example: if ftp(1), snmp(32) and snmpTrap(64) instances were selected, the value should be 97 (=1+32+64).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

maskingHighLevelProtCondition		1.3.6.1.4.1.164.4.1.6.3.1.19
Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by maskingHighLevelProt the packet contains data that matches the content of maskingHighLevelProt. false - Condition is valid if at the position specified by maskingHighLevelProt the packet contains data that does not match the content of maskingHighLevelProt.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	false(1), true(2)

maskingPortNum		1.3.6.1.4.1.164.4.1.6.3.1.20
The port number is the same as in high level protocol. It specifies the dest. port in IP case or the dest. socket in case of IPX & apple protocols. IP - This object is applicable only if none (0) value was selected in maskingHighLevelProt. IPX - This object is applicable only if the socket entered in maskingDestAddress is 'don't care'(00) AND maskingLowLevelProt is NOT ipxRip or ipxSap. Apple - This option is applicable only if the socket entered in maskingDestAddress is 'don't care'(00).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

maskingPortNumCondition		1.3.6.1.4.1.164.4.1.6.3.1.21
Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by maskingPortNum the packet contains data that matches the content of maskingPortNum. false - Condition is valid if at the position specified by maskingPortNum the packet contains data that does not match the content of maskingPortNum. This object is applicable only when maskingPortNum is applicable.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	false(1), true(2)

maskingOperation		1.3.6.1.4.1.164.4.1.6.3.1.22
The type of action to be taken if the frame meets the conditions of the mask. noOp = disabled (mask remains on list, but is not active) delete = mask is removed from the list. smartMask = the operation and destination of the mask will be determined by the objects of the Smart Table (old masking table: radBridgeMaskTable). If maskingType is codConnect, the 'block' value is NOT allowed. If maskingType is codDisconnect, the 'forward' value is NOT allowed.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	block(1), forward(2), route(3), forward-route(4), high-priority(5), noOp(6), delete(7), smartMask(8)

maskingSrcPortNum		1.3.6.1.4.1.164.4.1.6.3.1.23
The source port number. For IP: No Condition. For IPX: This object is applicable only if the socket entered in maskingSourceAddress is don't care (00) and maskingLowLevelProt is NOT ipxRip or ipxSap. For Apple:This object is applicable only if the socket entered in maskingSourceAddress is don't care (00).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

maskingSrcPortNumCondition		1.3.6.1.4.1.164.4.1.6.3.1.24
The same as 'maskingPortNumCondition'. Relates to source port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	false(1), true(2)

radBridgePerformance		1.3.6.1.4.1.164.4.1.7
OBJECT IDENTIFIER

radBridgeCurrentTable		1.3.6.1.4.1.164.4.1.7.1
The RAD Bridge Current table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RadBridgeCurrentEntry

radBridgeCurrentEntry		1.3.6.1.4.1.164.4.1.7.1.1
An entry in the RAD Bridge Current table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RadBridgeCurrentEntry

radBridgeCurrentIndex		1.3.6.1.4.1.164.4.1.7.1.1.1
The index of the Bridge interface or Bridge Port. It may be ifIndex.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

radBridgeCurrentIngressFilteringDiscardedFrames		1.3.6.1.4.1.164.4.1.7.1.1.2
The counter associated with the number of Discarded Frames upon Ingress Filtering, encountered by a Bridge interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

radBridgeCurrentFrameTypeDiscardedFrames		1.3.6.1.4.1.164.4.1.7.1.1.3
The counter associated with the number of Discarded Frames upon Frame Type and Tagging Mismatch, encountered by a Bridge interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

radBridgeCurrentRxCorrectFrames		1.3.6.1.4.1.164.4.1.7.1.1.4
The counter associated with the number of Received Correct Frames, encountered by a Bridge Port in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

radBridgeCurrentRxCorrectBytes		1.3.6.1.4.1.164.4.1.7.1.1.5
The counter associated with the number of Received Correct Bytes, encountered by a Bridge Port in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

radBridgeCurrentRxCorrectBytesHCOverflow		1.3.6.1.4.1.164.4.1.7.1.1.6
The counter associated with the number of times the associated radBridgeCurrentRxCorrectBytes counter has overflowed.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

radBridgeCurrentRxBcastFrames		1.3.6.1.4.1.164.4.1.7.1.1.7
The counter associated with the number of Received Broadcast Frames, encountered by a Bridge Port in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

radBridgeCurrentRxMcastFrames		1.3.6.1.4.1.164.4.1.7.1.1.8
The counter associated with the number of Received Multicast Frames, encountered by a Bridge Port in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

radBridgeCurrentTxCorrectFrames		1.3.6.1.4.1.164.4.1.7.1.1.9
The counter associated with the number of Transmitted Correct Frames, encountered by a Bridge Port in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

radBridgeCurrentTxCorrectBytes		1.3.6.1.4.1.164.4.1.7.1.1.10
The counter associated with the number of Transmitted Correct Bytes, encountered by a Bridge Port in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

radBridgeCurrentTxCorrectBytesHCOverflow		1.3.6.1.4.1.164.4.1.7.1.1.11
The counter associated with the number of times the associated radBridgeCurrentTxCorrectBytes counter has overflowed.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

radBridgeCurrentTxBcastFrames		1.3.6.1.4.1.164.4.1.7.1.1.12
The counter associated with the number of Transmitted Broadcast Frames, encountered by a Bridge Port in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

radBridgeCurrentTxMcastFrames		1.3.6.1.4.1.164.4.1.7.1.1.13
The counter associated with the number of Transmitted Multicast Frames, encountered by a Bridge Port in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

radBridgeCurrentTxDropFrames		1.3.6.1.4.1.164.4.1.7.1.1.14
The counter associated with the number of Transmitted Dropped Frames, encountered by a Bridge Port in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

radBridgeIntervalTable		1.3.6.1.4.1.164.4.1.7.2
The RAD Bridge Interval table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RadBridgeIntervalEntry

radBridgeIntervalEntry		1.3.6.1.4.1.164.4.1.7.2.1
An entry in the RAD Bridge Interval table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RadBridgeIntervalEntry

radBridgeIntervalIndex		1.3.6.1.4.1.164.4.1.7.2.1.1
The index of the bridge interface or Bridge Port. It may be ifIndex.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

radBridgeIntervalNumber		1.3.6.1.4.1.164.4.1.7.2.1.2
A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals exist).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..96

radBridgeIntervalIngressFilteringDiscardedFrames		1.3.6.1.4.1.164.4.1.7.2.1.3
The counter associated with the number of Discarded Frames upon Ingress Filtering, encountered by a Bridge interface in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

radBridgeIntervalFrameTypeDiscardedFrames		1.3.6.1.4.1.164.4.1.7.2.1.4
The counter associated with the number of Discarded Frames upon Frame Type and Tagging Mismatch, encountered by a Bridge interface in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

radBridgeIntervalRxCorrectFrames		1.3.6.1.4.1.164.4.1.7.2.1.5
The counter associated with the number of Received Correct Frames, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

radBridgeIntervalRxCorrectBytes		1.3.6.1.4.1.164.4.1.7.2.1.6
The counter associated with the number of Received Correct Bytes, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

radBridgeIntervalRxCorrectBytesHCOverflow		1.3.6.1.4.1.164.4.1.7.2.1.7
The counter associated with the number of times the associated radBridgeIntervalRxCorrectBytes counter has overflowed.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

radBridgeIntervalRxBcastFrames		1.3.6.1.4.1.164.4.1.7.2.1.8
The counter associated with the number of Received Broadcast Frames, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

radBridgeIntervalRxMcastFrames		1.3.6.1.4.1.164.4.1.7.2.1.9
The counter associated with the number of Received Multicast Frames, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

radBridgeIntervalTxCorrectFrames		1.3.6.1.4.1.164.4.1.7.2.1.10
The counter associated with the number of Transmitted Correct Frames, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

radBridgeIntervalTxCorrectBytes		1.3.6.1.4.1.164.4.1.7.2.1.11
The counter associated with the number of Transmitted Correct Bytes, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

radBridgeIntervalTxCorrectBytesHCOverflow		1.3.6.1.4.1.164.4.1.7.2.1.12
The counter associated with the number of times the associated radBridgeIntervalTxCorrectBytes counter has overflowed.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

radBridgeIntervalTxBcastFrames		1.3.6.1.4.1.164.4.1.7.2.1.13
The counter associated with the number of Transmitted Broadcast Frames, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

radBridgeIntervalTxMcastFrames		1.3.6.1.4.1.164.4.1.7.2.1.14
The counter associated with the number of Transmitted Multicast Frames, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

radBridgeIntervalTxDropFrames		1.3.6.1.4.1.164.4.1.7.2.1.15
The counter associated with the number of Transmitted Dropped Frames, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

radBridgePortBaseVlan		1.3.6.1.4.1.164.4.1.8
OBJECT IDENTIFIER

radBridgePortBaseVlanTable		1.3.6.1.4.1.164.4.1.8.1
A table containing static configuration information for each VLAN configured into the device by management. All entries are permanent and will be restored after the device is reset.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RadBridgePortBaseVlanEntry

radBridgePortBaseVlanEntry		1.3.6.1.4.1.164.4.1.8.1.1
Static information for a VLAN configured into the device by (local or network) management.
Status: current	Access: not-accessible
OBJECT-TYPE
	RadBridgePortBaseVlanEntry

radBridgePortBaseVlanCnfgIdx		1.3.6.1.4.1.164.4.1.8.1.1.1
This object indicates the Idx of the Agent Cnfg the following objects refer. 255=Temporary Cnfg (when relevant, Set is done only to this configuration). For Agents that support only one configuration, this object will be constant=1.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..255

radBridgePortBaseVlanIdx		1.3.6.1.4.1.164.4.1.8.1.1.2
Index of the port based VLAN.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

radBridgePortBaseVlanName		1.3.6.1.4.1.164.4.1.8.1.1.3
An administratively assigned string, which may be used to identify the the port based VLAN.
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString	Size(0..32)

radBridgePortBaseVlanEgressPorts		1.3.6.1.4.1.164.4.1.8.1.1.4
The set of ports which are permanently assigned to the egress list for this port based VLAN by management. The default value of this object is a string of zeros.
Status: current	Access: read-create
OBJECT-TYPE
	PortList

radBridgePortBaseVlanVirtualGroups		1.3.6.1.4.1.164.4.1.8.1.1.5
The set of Virtual Groups which are permanently assigned to this port based VLAN by management. (read Virtual Group instead of port in PortList Textual Convention) The default value of this object is a string of zeros.
Status: current	Access: read-create
OBJECT-TYPE
	PortList

radBridgePortBaseVlanRowStatus		1.3.6.1.4.1.164.4.1.8.1.1.6
This object enable user to create/delete entries in this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

radBridgePortBaseVlanMng		1.3.6.1.4.1.164.4.1.8.1.1.7
This object allows user to enable/disable management traffic on this VLAN. disable - only non-management data is allowed. enable - mixture of management traffic 0with other types of data is allowed.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), enable(3)

radBridgePortVlanMemberTable		1.3.6.1.4.1.164.4.1.8.2
The Bridge Ports-VLAN Membership table. This table enables the user to assign: - Several VLANs to a Port. - Several Ports to a VLAN.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RadBridgePortVlanMemberEntry

radBridgePortVlanMemberEntry		1.3.6.1.4.1.164.4.1.8.2.1
An entry in the Bridge Ports-VLANs Memebership table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RadBridgePortVlanMemberEntry

radBridgePortVlanMemberBridgeIdx		1.3.6.1.4.1.164.4.1.8.2.1.1
This object indicates the Bridge Index.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

radBridgePortVlanMemberPortIdx		1.3.6.1.4.1.164.4.1.8.2.1.2
This object indicates the Bridge's Port Index. For some cases, it can be used as the Port ofIndex.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

radBridgePortVlanMemberVlanId		1.3.6.1.4.1.164.4.1.8.2.1.3
This object indicates the VLAN ID.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

radBridgePortVlanMemberRowStatus		1.3.6.1.4.1.164.4.1.8.2.1.4
This object enables the user to create/delete entries in this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

radBridgeGenCnfg		1.3.6.1.4.1.164.4.1.9
OBJECT IDENTIFIER

radBridgeGenFlowTable		1.3.6.1.4.1.164.4.1.9.1
A table containing static configuration information for Bridge configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RadBridgeGenFlowEntry

radBridgeGenFlowEntry		1.3.6.1.4.1.164.4.1.9.1.1
Static information for a Bridge configured into the device by management.
Status: current	Access: not-accessible
OBJECT-TYPE
	RadBridgeGenFlowEntry

radBridgeGenFlowCnfgIdx		1.3.6.1.4.1.164.4.1.9.1.1.1
This object indicates the Idx of the Agent Cnfg the following objects refer. 255=Temporary Cnfg (when relevant Set is done only to this configuration). For Agents that support only one configuration, this object will be constant=1. This object can be used to carry additional indexing (e.g port index) when needed.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..2147483647

radBridgeGenFlowIdx		1.3.6.1.4.1.164.4.1.9.1.1.2
For Agent having more than one bridge, this index may be used as bridge index
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

radBridgeGenFlowRowStatus		1.3.6.1.4.1.164.4.1.9.1.1.3
This object enable user to create/delete entries in this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

radBridgeGenFlowFloodOrBcastMaxRate		1.3.6.1.4.1.164.4.1.9.1.1.4
This object controls maximum Flooding or Broadcast Rate: Max number of multicast along with unknown or flooded unicast frames allowed to enter any port. The number can be presented either as percentage of bandwidth, or bandwidth in Kbps. Once the limit is exceeded, any multicast or flooded frame entering from the port is discarded For RIC-155, and FCD-155 valid values are 3% , 6%, 12% and 100% = No Limit
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

radBridgeGenFlowQosMode		1.3.6.1.4.1.164.4.1.9.1.1.5
This object controls Quality of Service mode. User may select which field(s) (in case of fields - which one has precedence) will affect prioritization of data between egress queues.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notApplicable(1), vlanTag(2), dscp(3), dscpAndVlanTag(4), vlanTagAndDscp(5), none(6), tos(7), perPort(8), ipPrecedence(9), dsField(10), vlanTagAndTos(11), tosAndVlanTag(12), vlanTagAndIpPrecedence(13), ipPrecedenceAndVlanTag(14), vlanTagAndDsField(15), dsFieldAndVlanTag(16)

radBridgeGenFlowSchedulingMode		1.3.6.1.4.1.164.4.1.9.1.1.6
This object controls which scheduling mode is used: Weighted Fair Queuing (WFQ) scheme, Strict Priority (SP) or ATM CoS
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notApplicable(1), wfq(2), sp(3), atmCos(4)

radBridgeGenFlowBasicClassification		1.3.6.1.4.1.164.4.1.9.1.1.7
This object defines whether Classification based on Port should be taken into account (either as default, or in addition to other classifications).
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	none(2), port(3)

radBridgeGenFlowMulticastTrafficClass		1.3.6.1.4.1.164.4.1.9.1.1.8
The Traffic Class the received Multicast frame is mapped to.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

radBridgeGenFlowBroadcastTrafficClass		1.3.6.1.4.1.164.4.1.9.1.1.9
The Traffic Class the received Broadcast frame is mapped to.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

radBridgeGenFlowUnkownUnicastTrafficClass		1.3.6.1.4.1.164.4.1.9.1.1.10
The Traffic Class the received Unkonwn Unicast frame is mapped to.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

radBridgeDot1qVlanStaticTable		1.3.6.1.4.1.164.4.1.9.2
A table containing static configuration information for each VLAN configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RadBridgeDot1qVlanStaticEntry

radBridgeDot1qVlanStaticEntry		1.3.6.1.4.1.164.4.1.9.2.1
Static information for a VLAN configured into the device by (local or network) management.
Status: current	Access: not-accessible
OBJECT-TYPE
	RadBridgeDot1qVlanStaticEntry

radBridgeDot1qVlanTaggedPorts		1.3.6.1.4.1.164.4.1.9.2.1.1
The set of ports which should transmit egress packets for this VLAN as tagged.
Status: current	Access: read-create
OBJECT-TYPE
	PortList

radBridgeDot1qVlanUnmodifiedPorts		1.3.6.1.4.1.164.4.1.9.2.1.2
The set of ports which should transmit egress packets for this VLAN as unmodified.
Status: current	Access: read-create
OBJECT-TYPE
	PortList

radBridgeDot1qVlanSplitHorizon		1.3.6.1.4.1.164.4.1.9.2.1.3
When 'enable (3)', packets having this VLAN will not be switched back to other bridge ports which are members of this VLAN.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), enable(3)

radBridgeStatus		1.3.6.1.4.1.164.4.1.10
OBJECT IDENTIFIER

radBridgeInvBasePortTable		1.3.6.1.4.1.164.4.1.10.1
An inversed table to dot1dBasePortTable from RFC1493 with reduced information. This table index is known to the NMS and this way the needed information can be received by just one Get command, instead of searching the entire dot1dBasePortTable (where it is an attribute).
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RadBridgeInvBasePortEntry

radBridgeInvBasePortEntry		1.3.6.1.4.1.164.4.1.10.1.1
The bridge port number for each bridge port interface index.
Status: current	Access: not-accessible
OBJECT-TYPE
	RadBridgeInvBasePortEntry

radBridgeInvBasePortIfIndex		1.3.6.1.4.1.164.4.1.10.1.1.1
The value of the instance of the ifIndex object, defined in MIB-II, for the interface corresponding to this Bridge port.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

radBridgeInvBasePort		1.3.6.1.4.1.164.4.1.10.1.1.2
The Bridge port number.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

radBridgeStp		1.3.6.1.4.1.164.4.1.11
OBJECT IDENTIFIER

radBridgeStpCnfgTable		1.3.6.1.4.1.164.4.1.11.1
STP Configuration table. STP=Spanning Tree Protocol. It includes STP configurable parameters that in BRIDGE-MIB are scalars, while we need them per card/bridge/interface and per different configurations.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RadBridgeStpCnfgEntry

radBridgeStpCnfgEntry		1.3.6.1.4.1.164.4.1.11.1.1
An entry in the radBridgeStpCnfgTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	RadBridgeStpCnfgEntry

radBridgeStpCnfgIdx1		1.3.6.1.4.1.164.4.1.11.1.1.1
This object indicates the Index of the Agent Configuration the following objects refer to. For Agents that support more than one configuration: 255=Temporary Cnfg ; Set can be done only to this configuration. For Agents that support only one configuration, this object will be constant=1.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..255

radBridgeStpCnfgIdx2		1.3.6.1.4.1.164.4.1.11.1.1.2
For Agents having the table objects per Card/Bridge/Interface this will be the index of the Card/Bridge/Interface used.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

radBridgeStpCnfgForwardDelay		1.3.6.1.4.1.164.4.1.11.1.1.3
The value that the bridge of radBridgeStpCnfgIdx2 uses for Forward Delay when this bridge is acting as the root. Note that the range for this parameter is related to the value of radBridgeStpCnfgMaxAge (according to 802.1D-1990 for the similar scalars of BRIDGE-MIB). The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
Status: current	Access: read-write
OBJECT-TYPE
	Timeout	400..3000

radBridgeStpCnfgMaxAge		1.3.6.1.4.1.164.4.1.11.1.1.4
The value that the bridge of radBridgeStpCnfgIdx2 uses for MaxAge when this bridge is acting as the root. Note that the range for this parameter is related to the value of radBridgeStpCnfgHelloTime (according to 802.1D-1990 for the similar scalars of BRIDGE-MIB). The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
Status: current	Access: read-write
OBJECT-TYPE
	Timeout	600..4000

radBridgeStpCnfgHelloTime		1.3.6.1.4.1.164.4.1.11.1.1.5
The value that the bridge of radBridgeStpCnfgIdx2 uses for Hello Time when this bridge is acting as the root. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
Status: current	Access: read-write
OBJECT-TYPE
	Timeout	100..1000

radBridgeStpCnfgPriority		1.3.6.1.4.1.164.4.1.11.1.1.6
The value of the write-able portion of the Bridge ID, i.e., the first two octets of the (8 octet long) Bridge ID, per radBridgeStpCnfgIdx2 instance.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..65535

radBridgeStpCnfgStpVersion		1.3.6.1.4.1.164.4.1.11.1.1.7
This object determines the STP version used: stp - usual Spanning Tree Protocol. rstp - Rapid Spanning Tree Protocol.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), stp(2), rstp(3)

radBridgeStpStatTable		1.3.6.1.4.1.164.4.1.11.2
STP Status table. STP=Spanning Tree Protocol. It includes STP status parameters that in BRIDGE-MIB are scalars, while we need them per card/bridge/interface. For devices that have several configurations, this table is for Status of the Active configuration.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RadBridgeStpStatEntry

radBridgeStpStatEntry		1.3.6.1.4.1.164.4.1.11.2.1
An entry in the radBridgeStpStatTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	RadBridgeStpStatEntry

radBridgeStpStatIdx		1.3.6.1.4.1.164.4.1.11.2.1.1
For Agents having the table objects per Card/Bridge/Interface this will be the index of the Card/Bridge/Interface used.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

radBridgeStpStatForwardDelay		1.3.6.1.4.1.164.4.1.11.2.1.2
This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. [Note that this value is the one that this bridge is currently using, in contrast to radBridgeStpCnfgForwardDelay which is the value that this bridge would start using if/when this bridge were to become the root.]
Status: current	Access: read-only
OBJECT-TYPE
	Timeout

radBridgeStpStatMaxAge		1.3.6.1.4.1.164.4.1.11.2.1.3
The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.
Status: current	Access: read-only
OBJECT-TYPE
	Timeout

radBridgeStpStatHelloTime		1.3.6.1.4.1.164.4.1.11.2.1.4
The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using.
Status: current	Access: read-only
OBJECT-TYPE
	Timeout

radBridgeStpStatDesignatedRoot		1.3.6.1.4.1.164.4.1.11.2.1.5
The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
Status: current	Access: read-only
OBJECT-TYPE
	BridgeId

radBridgeStpStatRootCost		1.3.6.1.4.1.164.4.1.11.2.1.6
The cost of the path to the root as seen from this bridge.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

radBridgeForwardingMode		1.3.6.1.4.1.164.4.1.12
This object determines the Bridge Forwarding Mode: transparent - Forward all frames received (not dependent on VLAN). filter - Filter frames received according to MAC Address. filterTagged = Filter frames received according to VLAN. transparentTagged = VLAN aware + Transparent.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), transparent(2), filter(3), filterTagged(4), transparentTagged(5)

radBridgePort		1.3.6.1.4.1.164.4.1.13
OBJECT IDENTIFIER

radBridgePortCnfgTable		1.3.6.1.4.1.164.4.1.13.1
The Bridge Port Configuration Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RadBridgePortCnfgEntry

radBridgePortCnfgEntry		1.3.6.1.4.1.164.4.1.13.1.1
An entry in the table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RadBridgePortCnfgEntry

radBridgePortCnfgIdx		1.3.6.1.4.1.164.4.1.13.1.1.1
The first index of the table. It can serve for Configuration index, Bridge index or other.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

radBridgePortCnfgPrtIdx		1.3.6.1.4.1.164.4.1.13.1.1.2
This object indicates the Bridge Port index.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

radBridgePortCnfgMaxMacAddr		1.3.6.1.4.1.164.4.1.13.1.1.3
This object indicates the maximum number of total MAC Addresses (static and learned) supported by this Bridge Port.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

radBridgePortCnfgMngFlow		1.3.6.1.4.1.164.4.1.13.1.1.4
This object indicates whether this Bridge Port is dedicated for management flow.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(2), enable(3)

radBridgePortCnfgMcastMode		1.3.6.1.4.1.164.4.1.13.1.1.5
This object indicates this Bridge Port's Multicast Mode: flooding (1) - flood multicast MAC addresses forwarding (2) - forward multicast MAC addresses to the subnet indicated.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	flooding(1), forwarding(2)

radBridgePortCnfgDefaultVpi		1.3.6.1.4.1.164.4.1.13.1.1.6
This object indicates the VPI of this Bridge Port's Default VCL. An incoming frame with priority that is not assigned to any VCL will be transferred to the Default VCL.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

radBridgePortCnfgDefaultVci		1.3.6.1.4.1.164.4.1.13.1.1.7
This object indicates the VCI of this Bridge Port's Default VCL. An incoming frame with priority that is not assigned to any VCL will be transferred to the Default VCL.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

radBridgePortCnfgStatVlanId		1.3.6.1.4.1.164.4.1.13.1.1.8
This object indicates the selected VlanId of the bridge port on which statistics are being collected. 0=no Statistics collected for VLAN on this bridge port.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

radBridgePortCnfgIngressMtu		1.3.6.1.4.1.164.4.1.13.1.1.9
The size of the largest packet which can be received on the interface, specified in octets.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

radBridgePortCnfgEgressMtu		1.3.6.1.4.1.164.4.1.13.1.1.10
The size of the largest packet which can be sent on the interface, specified in octets.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

radBridgePortCnfgDot1x		1.3.6.1.4.1.164.4.1.13.1.1.11
This feature is currently supported via the variable ethIfTable.ethDot1xEnable. Determnines if the Port-Based Network Access Protocol (IEEE-802.1x)is enabled for the bridge Port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(2), enabled(3)

radDot1qPortVlanTable		1.3.6.1.4.1.164.4.1.9.3
A table containing control and status information for VLAN configuration per port.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RadDot1qPortVlanEntry

radDot1qPortVlanEntry		1.3.6.1.4.1.164.4.1.9.3.1
Information controlling VLAN configuration for a port. This is indexed by dot1dBasePort.
Status: current	Access: not-accessible
OBJECT-TYPE
	RadDot1qPortVlanEntry

radDot1qPortStacking		1.3.6.1.4.1.164.4.1.9.3.1.1
This object indicates the port stacking operation: unmodify (2) = Do not add Tag. tag (3) = Add Tag to Untagged Frames. stack (4) = Add Tag to all Frames.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), unmodify(2), tag(3), stack(4)

radDot1qPortCopyOriginVlanPriority		1.3.6.1.4.1.164.4.1.9.3.1.2
This object indicates whether use the original VLAN Priority of the frame, as the priority of the VLAN added by this port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), no(2), yes(3)

radDot1qPortDefaultVlanPriority		1.3.6.1.4.1.164.4.1.9.3.1.3
Default VLAN Frame priority of the VLAN added by this port.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

radDot1qPortTagStripping		1.3.6.1.4.1.164.4.1.9.3.1.4
This object indicates whether remove a tag from the frame on this port, frame with double tag will remain with one tag and frame with one tag will remain untagged.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), no(2), yes(3)

radDot1qPortEgressTagHandling		1.3.6.1.4.1.164.4.1.9.3.1.5
This object indicates how is the Egress VLAN Tag processed. It is mainly for use with Double Tagging.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(2), stacking(3), stripping(4)

radDot1qPortIngressTagHandling		1.3.6.1.4.1.164.4.1.9.3.1.6
This object indicates how is the Ingress VLAN Tag processed. It is mainly for use with Double Tagging.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(2), stacking(3), stripping(4)

radDot1qPortReplaceVlanPriority		1.3.6.1.4.1.164.4.1.9.3.1.7
This object indicates whether for each received tagged frame on this Bridge Port - VLAN Priority will be replaced by another Priority. no(2) = no repacement yes(3) = VLAN Priority will be replaced For Egate-100: When value is 'yes', the original Priority is replaced by the Default Priority.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), no(2), yes(3)

radDot1qPortVlanEthType		1.3.6.1.4.1.164.4.1.9.3.1.8
This object indicates the Ethernet Type. For some devices, it is applicable only when radDot1qPortStacking = stack.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

radDot1qPortVlanCnodeLevel1Agent		1.3.6.1.4.1.164.4.1.9.3.1.9
Specify if a Level 1 cNode agent is enabled or not for the bridge port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(2), enable(3)

radBridgeGenCfgTable		1.3.6.1.4.1.164.4.1.9.4
A table containing Bridge configuration parameters.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RadBridgeGenCfgEntry

radBridgeGenCfgEntry		1.3.6.1.4.1.164.4.1.9.4.1
Describes an entry in the radBridgeGenCfgTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	RadBridgeGenCfgEntry

radBridgeGenCfgIdx		1.3.6.1.4.1.164.4.1.9.4.1.1
This object indicates the Idx of the Agent Cnfg the following objects refer. 255=Temporary Cnfg. For Agents that support only one Configuration, this object will be constant=1.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..255

radBridgeGenCfgIdx2		1.3.6.1.4.1.164.4.1.9.4.1.2
For Agents having more than one bridge, this index may be used as bridge index
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

radBridgeGenCfgBridgeAction		1.3.6.1.4.1.164.4.1.9.4.1.3
This variable enables the operator to perform one of the specified actions on the tables maintained by the Bridge. After performing the action, Agent will automatically Set the value of this variable to noOp(255).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	deleteLanTab(7), noOp(255)

radBridgeAgingTimeSec		1.3.6.1.4.1.164.4.1.9.4.1.4
This variable duplicates scalar object dot1dTpAgingTimeThe of BRIDGE-MIB with configuration index and Bridge index. It defines the timeout period in seconds for aging out dynamically learned forwarding information. 802.1D-1990 recommends a default of 300 seconds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	10..1000000

radBridgeMngVlanId		1.3.6.1.4.1.164.4.1.9.4.1.5
This variable indicates the VLAN ID used for remote management traffic. 0 = Not Applicable.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

radBridgeLoopDetectVlanId		1.3.6.1.4.1.164.4.1.9.4.1.6
This variable indicates the VLAN ID used for Loop Detection packets. Valid values: 1 - 4095: VLAN ID 0 - Means that the Loop Detection is Disabled.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

radBridgeSplitHorizon		1.3.6.1.4.1.164.4.1.9.4.1.7
This object configure 'split horizon' switching between bridge Ports. - disable - normal (VLAN aware) bridge behavior. - enable - all packets, regardless their VLAN, coming from user side are blocked from being switched back to other user side bridge ports. - vlanBased - split horizon behavior is applicable only for specific VLANs, according to radBridgeDot1qVlanSplitHorizon.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), enabled(3), vlanBased(4)

radBridgeEthType		1.3.6.1.4.1.164.4.1.9.4.1.8
Value of Ethertype field in Ethernet frame. This field indicates which protocol is being transported in an ethernet frame.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

radBridgeAgingTime		1.3.6.1.4.1.164.4.1.9.5
This variable defines whether the Aging Time will be finite or infinite. When selecting the finite (3) value, the exact time will be determined by another variable of the standard MIB (ex. 1493.dot1dTpAgingTime). or by radBridgeAgingTime below.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), infinite(2), finite(3)

radBridgeMngFlow		1.3.6.1.4.1.164.4.1.9.6
This variable defines whether the Management Flow is passed through the bridge (enable) or not (disable).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(2), enable(3)

wanGen		1.3.6.1.4.1.164.3.1
OBJECT IDENTIFIER

muxHub		1.3.6.1.4.1.164.3.2
OBJECT IDENTIFIER

chasWanGen		1.3.6.1.4.1.164.3.1.1
OBJECT IDENTIFIER

agnWanGen		1.3.6.1.4.1.164.3.1.2
OBJECT IDENTIFIER

mdlWanGen		1.3.6.1.4.1.164.3.1.3
OBJECT IDENTIFIER

prtWanGen		1.3.6.1.4.1.164.3.1.4
OBJECT IDENTIFIER

mapWanGen		1.3.6.1.4.1.164.3.1.5
OBJECT IDENTIFIER

diverseIfWanGen		1.3.6.1.4.1.164.3.1.6
OBJECT IDENTIFIER

statAgnGen		1.3.6.1.4.1.164.3.1.2.1
OBJECT IDENTIFIER

cnfgAgnGen		1.3.6.1.4.1.164.3.1.2.2
OBJECT IDENTIFIER

cmprAgnGen		1.3.6.1.4.1.164.3.1.2.3
OBJECT IDENTIFIER

alrBuffGen		1.3.6.1.4.1.164.3.1.2.4
OBJECT IDENTIFIER

agnFlipDb		1.3.6.1.4.1.164.3.1.2.5
OBJECT IDENTIFIER

agnSa		1.3.6.1.4.1.164.3.1.2.6
OBJECT IDENTIFIER

agnListDecoding		1.3.6.1.4.1.164.3.1.2.7
OBJECT IDENTIFIER

agnSystemDlci		1.3.6.1.4.1.164.3.1.2.8
OBJECT IDENTIFIER

agnVoiceSwitching		1.3.6.1.4.1.164.3.1.2.9
OBJECT IDENTIFIER

agnSigProfile		1.3.6.1.4.1.164.3.1.2.10
OBJECT IDENTIFIER

agnSystemTs		1.3.6.1.4.1.164.3.1.2.11
OBJECT IDENTIFIER

systemVoice		1.3.6.1.4.1.164.3.1.2.12
OBJECT IDENTIFIER

statMdlGen		1.3.6.1.4.1.164.3.1.3.1
OBJECT IDENTIFIER

cnfgMdlGen		1.3.6.1.4.1.164.3.1.3.2
OBJECT IDENTIFIER

cmprMdlGen		1.3.6.1.4.1.164.3.1.3.3
OBJECT IDENTIFIER

statPrtGen		1.3.6.1.4.1.164.3.1.4.1
OBJECT IDENTIFIER

cnfgPrtGen		1.3.6.1.4.1.164.3.1.4.2
OBJECT IDENTIFIER

cmprPrtGen		1.3.6.1.4.1.164.3.1.4.3
OBJECT IDENTIFIER

agnMux		1.3.6.1.4.1.164.3.2.1
OBJECT IDENTIFIER

mdlMux		1.3.6.1.4.1.164.3.2.2
OBJECT IDENTIFIER

prtMux		1.3.6.1.4.1.164.3.2.3
OBJECT IDENTIFIER

statPrtMux		1.3.6.1.4.1.164.3.2.3.1
OBJECT IDENTIFIER

cnfgPrtMux		1.3.6.1.4.1.164.3.2.3.2
OBJECT IDENTIFIER

statisPrtGen		1.3.6.1.4.1.164.3.1.4.1.3
OBJECT IDENTIFIER

prtFrStatis		1.3.6.1.4.1.164.3.1.4.1.3.1
OBJECT IDENTIFIER

prtCrStatis		1.3.6.1.4.1.164.3.1.4.1.3.2
OBJECT IDENTIFIER

prtDlciStatis		1.3.6.1.4.1.164.3.1.4.1.3.3
OBJECT IDENTIFIER

prtT1Statis		1.3.6.1.4.1.164.3.1.4.1.3.4
OBJECT IDENTIFIER

prtClCnfg		1.3.6.1.4.1.164.3.2.3.2.1
OBJECT IDENTIFIER

prtPh1MlCnfg		1.3.6.1.4.1.164.3.2.3.2.2
OBJECT IDENTIFIER

prtPhPlCnfg		1.3.6.1.4.1.164.3.2.3.2.3
OBJECT IDENTIFIER

prtLs2Cnfg		1.3.6.1.4.1.164.3.2.3.2.4
OBJECT IDENTIFIER

prtHs4Cnfg		1.3.6.1.4.1.164.3.2.3.2.7
OBJECT IDENTIFIER

prtHsiCnfg		1.3.6.1.4.1.164.3.2.3.2.8
OBJECT IDENTIFIER

prtPVc4Cnfg		1.3.6.1.4.1.164.3.2.3.2.9
OBJECT IDENTIFIER

prtHsrCnfg		1.3.6.1.4.1.164.3.2.3.2.10
OBJECT IDENTIFIER

prtMbeCnfg		1.3.6.1.4.1.164.3.2.3.2.11
OBJECT IDENTIFIER

prtTreCnfg		1.3.6.1.4.1.164.3.2.3.2.12
OBJECT IDENTIFIER

prtLs6Cnfg		1.3.6.1.4.1.164.3.2.3.2.13
OBJECT IDENTIFIER

prtVc3Cnfg		1.3.6.1.4.1.164.3.2.3.2.14
OBJECT IDENTIFIER

prtVcPbxCnfg		1.3.6.1.4.1.164.3.2.3.2.15
OBJECT IDENTIFIER

prtIsdnCnfg		1.3.6.1.4.1.164.3.2.3.2.16
OBJECT IDENTIFIER

prtLogicalCnfg		1.3.6.1.4.1.164.3.2.3.2.17
OBJECT IDENTIFIER

prtFrPlusCnfg		1.3.6.1.4.1.164.3.2.3.2.18
OBJECT IDENTIFIER

prtMl4Cnfg		1.3.6.1.4.1.164.3.2.3.2.19
OBJECT IDENTIFIER

prtAcmCnfg		1.3.6.1.4.1.164.3.2.3.2.20
OBJECT IDENTIFIER

prtE2Cnfg		1.3.6.1.4.1.164.3.2.3.2.21
OBJECT IDENTIFIER

prtLanWanCnfg		1.3.6.1.4.1.164.3.2.3.2.22
OBJECT IDENTIFIER

chasVersion		1.3.6.1.4.1.164.3.1.1.1
An ASCII string for description and display of the agent chassis version.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

chasTotalNoOfSlt		1.3.6.1.4.1.164.3.1.1.2
This entry indicates the number of physical slots in the chassis.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

chasTotalNoOfIoSlt		1.3.6.1.4.1.164.3.1.1.3
This entry indicates the total number of physical IO slots in the chassis, (not all slots hardware should be occupied and active) .
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

chasTotalNoOfPsSlt		1.3.6.1.4.1.164.3.1.1.4
This entry indicates the number of physical Power Supply slots in the chassis.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

chasTotalNoOfClSlt		1.3.6.1.4.1.164.3.1.1.5
This entry indicates the number of physical Common Logic slots in the chassis.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnSDateFormat		1.3.6.1.4.1.164.3.1.2.1.1
This entry indicates the date and time format used for the agnSDateAndTimeCmd and for the alarm history report.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ddMMYYYY(1), mmDDYYYY(2), yyyyDDMM(3), yyyyMMDD(4)

agnSDateCmd		1.3.6.1.4.1.164.3.1.2.1.2
This entry indicates the current date as it is known by the agent using its own real-time clock. The format would be as specified by the agnSDateFormat. This parameter can be set for time synchronization between the NMS and the Agent.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

agnSTimeCmd		1.3.6.1.4.1.164.3.1.2.1.3
This entry indicates the current time as it is known by the agent using its own real-time clock. This parameter can be set for time synchronization between the NMS and the Agent.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

agnSActiveCnfg		1.3.6.1.4.1.164.3.1.2.1.4
This entry specifies the unique identifier of the configuration, that is currently active and running.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnSEditCnfg		1.3.6.1.4.1.164.3.1.2.1.5
This entry indicates the unique identifier of the configuration that is currently loaded into the tmp working space for manipulation and update operations. Value of 255 means no config. is under editing process.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnSLastCnfgFlipTime		1.3.6.1.4.1.164.3.1.2.1.6
This entry indicates the Date & Time of the last flip to the current configuration at the agent.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

agnSLastCnfgFlipCause		1.3.6.1.4.1.164.3.1.2.1.7
This entry describes the flip's cause.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

agnSEditBy		1.3.6.1.4.1.164.3.1.2.1.8
This entry indicates which MMI application is working on the edited config. The editing phase starts at the first modify operation and ends after an update(load) operation.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), snmp(2), terCon1(3), terCon2(4), terInbandCon1(5), terInbandCon2(6), lcd(7)

agnSClkSrc		1.3.6.1.4.1.164.3.1.2.1.9
This entry indicates the source of the system clock.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	master(1), fallback(2), internal(3)

agnSAlrStatus		1.3.6.1.4.1.164.3.1.2.1.10
Indicates the alarm state in the agent level, i.e. lower level (card/port) alarms not included. critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), event(3), minor(4), major(5), warning(6), critical(7)

agnSAlrStatusAll		1.3.6.1.4.1.164.3.1.2.1.11
Indicates the alarm state of the entire agent, i.e. including card and port alarms status. critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), event(3), minor(4), major(5), warning(6), critical(7)

agnSMaskedAlrStat		1.3.6.1.4.1.164.3.1.2.1.12
Indicates the alarm state in the agent level,[ i.e. lower level (card/port) alarms not included] including Masked alarms. critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), event(3), minor(4), major(5), warning(6), critical(7)

agnSMaskedAlrStatAll		1.3.6.1.4.1.164.3.1.2.1.13
Indicates the alarm state of the entire agent, i.e. including card and port alarms status,including Masked alarms. critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), event(3), minor(4), major(5), warning(6), critical(7)

agnSTstStatAll		1.3.6.1.4.1.164.3.1.2.1.14
on(3) - when there is at least one test in progress in one of the agent cards, otherwise the value will be off(2).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), on(3)

agnSAlrTable		1.3.6.1.4.1.164.3.1.2.1.15
List of agent related alarms and indications for alarms at system level.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AgnSAlrEntry

agnSAlrEntry		1.3.6.1.4.1.164.3.1.2.1.15.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AgnSAlrEntry

agnSAlrIdx		1.3.6.1.4.1.164.3.1.2.1.15.1.1
A unique number to identify an entry in the alarm status table of the agent.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnSAlrCodeDescription		1.3.6.1.4.1.164.3.1.2.1.15.1.2
This attribute is a full text description of the alarm . The alarm description includes the following information: alarm code, alarm text, alarm severity, Masked or Inverted flag and counter.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

agnSAlrCode		1.3.6.1.4.1.164.3.1.2.1.15.1.3
A code identifying the alarm of an entry in the alarm status table at system level.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnSAlrSeverity		1.3.6.1.4.1.164.3.1.2.1.15.1.4
The severity of the alarm.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	event(3), minor(4), major(5), warning(6), critical(7)

agnSAlrState		1.3.6.1.4.1.164.3.1.2.1.15.1.5
State of the alarm.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), on(3)

agnSAlrCounter		1.3.6.1.4.1.164.3.1.2.1.15.1.6
A counter - how many times the alarm occured since last clear operation. ON and OFF Alarm will be counted separately.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnSAlrMask		1.3.6.1.4.1.164.3.1.2.1.15.1.7
Alarm mask : on/off.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), on(3)

agnSAlrInvert		1.3.6.1.4.1.164.3.1.2.1.15.1.8
Alarm invert : on/off.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), on(3)

agnSClearAlrCmd		1.3.6.1.4.1.164.3.1.2.1.16
Setting this attribute to ON, enforce a clear operation on all the agent(general) events. General alarms are alarms which are not specific to a card or port. The clear operation will not be applied for masked/inverted alarms.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

agnSClearAllAlrCmd		1.3.6.1.4.1.164.3.1.2.1.17
Setting this attribute to ON, enforce a clear operation on all MUX alarm events at the levels of agent, slots and ports. The clear operation will not be applied for masked/inverted alarms.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

agnSSanityCheckStatus		1.3.6.1.4.1.164.3.1.2.1.18
Upon completion of the Sanity check process on the TmpCnfg this attribute will be set to: FAIL(2) - when there is at least one error encountered and possibly some warnings. WARNING(3) - when there are only warnings. otherwise, the value will be OK(4). The value will be UNKNOWN(1) if changes were made in the TmpCnfg following the last Sanity check.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), fail(2), warning(3), ok(4)

agnSNoOfSanityCheckErr		1.3.6.1.4.1.164.3.1.2.1.19
This entry indicates the number of errors/warnings discovered by the last SanityCheck process.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnSErrListTable		1.3.6.1.4.1.164.3.1.2.1.20
List of errors and warnings found during Sanity Check process.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AgnSErrListEntry

agnSErrListEntry		1.3.6.1.4.1.164.3.1.2.1.20.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AgnSErrListEntry

agnSErrIdx		1.3.6.1.4.1.164.3.1.2.1.20.1.1
Unique number to identify an entry in the error list table. The maximum entry value cannot exceed the value of 'agnSNoOfSanityCheckErr'.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnSErrDescription		1.3.6.1.4.1.164.3.1.2.1.20.1.2
This attribute is a full text description of the sanity check error including error code, slot and port numbers related to the code .
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

agnSMaxNoOfCnfg		1.3.6.1.4.1.164.3.1.2.1.21
Maximum number of configurations that can be defined and stored in the MUX. If the mux has a large capacity, the maximum will be limited to 254.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnSCnfgTable		1.3.6.1.4.1.164.3.1.2.1.22
This table contains an entry per configuration. It indicates if the configuration is valid.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AgnSCnfgEntry

agnSCnfgEntry		1.3.6.1.4.1.164.3.1.2.1.22.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AgnSCnfgEntry

agnSEntryIdx		1.3.6.1.4.1.164.3.1.2.1.22.1.1
Unique number to identify an entry in the configuration table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnSEntryIsValid		1.3.6.1.4.1.164.3.1.2.1.22.1.2
This attribute indicates whether the specific configuration is valid in the MUX . Value of NO indicates: no such configuration in the MUX.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	no(2), yes(3)

agnCSanityCheckCmd		1.3.6.1.4.1.164.3.1.2.2.1
Setting this attribute to on(3) will initiate the process of Sanity check on the TmpCnfg. Upon completion the value will automatically be changed to off(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

agnCSaveCnfgIdxCmd		1.3.6.1.4.1.164.3.1.2.2.2
This attribute specifies the Id of the target RealCnfg to which the TmpCnfg should be transferred. Upon set command the MUX will initiate the Sanity-Check process first. If successful, the actual transfer will be performed. If warnings are detected, the user will have to perform the command again to confirm the operation. Setting this object a second time to the same value without performing any change in the database, will cause the result: agnSSanityCheckStatus = unknown
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..100

agnCLoadCnfgIdxCmd		1.3.6.1.4.1.164.3.1.2.2.3
This attribute specifies the Id of the source Cnfg to be loaded into the TmpCnfg. Upon set operation the actual transfer will be initiated. The operation is valid only on Valid configurations (agnSEntryIsValid)
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..100

agnCClkSrcTable		1.3.6.1.4.1.164.3.1.2.2.4
All the entries of this table are identical (have the same value) for all the configurations (1..100) except the TmpCnfg. The write operation into the Table Objects is valid only for the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AgnCClkSrcEntry

agnCClkSrcEntry		1.3.6.1.4.1.164.3.1.2.2.4.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AgnCClkSrcEntry

agnCClkCnfgIdx		1.3.6.1.4.1.164.3.1.2.2.4.1.1
This attribute indicates the Idx of the Cnfg(1..100) being accessed and Idx 255 relates to the TmpCnfg.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

agnCClkSrcIdx		1.3.6.1.4.1.164.3.1.2.2.4.1.2
An index to the table. There are only two entries to this table. Index 1 points to the Master clock parameters and Index 2 points to the Fallback clock parameters
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..2

agnCClkSrcMode		1.3.6.1.4.1.164.3.1.2.2.4.1.3
The source of the nodal timing.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	internal(1), rxClk(2), adaptive(3)

agnCClkSrcSlt		1.3.6.1.4.1.164.3.1.2.2.4.1.4
This entry is valid only when we are working in rxClk mode. For an invalid entry, the return value will be '7fff'h.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

agnCClkSrcPrt		1.3.6.1.4.1.164.3.1.2.2.4.1.5
This entry is valid only when we are working in rxClk or adaptive mode. For an invalid entry, the return value will be '7fff'h. - For rxClk mode, the values can be: exPrt1 (1) , exPrt2 (2) , exPrt3 (3) , exPrt4 (4) , exPrt5 (5) , exPrt6 (6) , exPrt7 (7) , exPrt8 (8) , exPrt9 (9) , exPrt10 (10) , exPrt11 (11) , exPrt12 (12) , notApplicable (100), inPrt1 (101) , inPrt2 (102) , inPrt3 (103) , inPrt4 (104) - For adaptive mode, the value will be the ifIndex of the selected IP Bundle.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

agnCDeleteCnfgIdxCmd		1.3.6.1.4.1.164.3.1.2.2.5
Setting this attribute will delete the requested DB from the NVRAM .
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..100

agnCDefaultCnfgIdxCmd		1.3.6.1.4.1.164.3.1.2.2.6
Setting this attribute will define the desired working configuration when no conditions of the Flip DB Table are fulfilled and no Net GO command was issued. This command will be accepted only if the Configuration number exists (agnSEntryIsValid=yes).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..100

agnCnfgDataTable		1.3.6.1.4.1.164.3.1.2.2.7
This table contains data about the agent configurations. The table will support only data about valid configurations of the agent.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AgnCnfgDataEntry

agnCnfgDataEntry		1.3.6.1.4.1.164.3.1.2.2.7.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AgnCnfgDataEntry

agnCnfgIdx		1.3.6.1.4.1.164.3.1.2.2.7.1.1
This object indicates the Idx of the agent' Cnfg the following objects refer. 255=Temporary Cnfg (Set is done only to this configuration).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

agnCnfgDesc		1.3.6.1.4.1.164.3.1.2.2.7.1.2
This object is a description of the Configuration, entered by user, to enhance Cnfg recognition.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..30)

agnCnfgUpdDate		1.3.6.1.4.1.164.3.1.2.2.7.1.3
This object indicates the date when last update of this configuration was performed, as it is known by the agent using its own real-time clock. The format would be as specified by the agnSDateFormat. When update is performed, the agent should save the date.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

agnCnfgUpdTime		1.3.6.1.4.1.164.3.1.2.2.7.1.4
This object indicates the time when last update of this configuration was performed, as it is known by the agent using its own real-time clock. When update is performed, the agent should save the time.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

agnCnfgUpdMnger		1.3.6.1.4.1.164.3.1.2.2.7.1.5
This object indicates the IP Address of the Manager who performed the last update of this configuration. When update is performed, the agent should save the IP Address of the Manager who commanded the update. That will enable a manager to know if he performed the last update, or another manager did.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

agnCnfgAlarm		1.3.6.1.4.1.164.3.1.2.2.8
OBJECT IDENTIFIER

agnCnfgAlrFilterWindow		1.3.6.1.4.1.164.3.1.2.2.8.1
Window of time, in seconds. During this Window, the alarms filter is performed. Same Window for all agent alarms that need filtering. Upon end of the Window, the state of the alarm is updated and a new Window starts. If no alarm needs filtering, this object's value will not be used.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..255

agnCnfgAlrTable		1.3.6.1.4.1.164.3.1.2.2.8.2
This table enables the user to set attributes to each alarm. Setting for a non-existing entry agnCnfgAlrMask, agnCnfgAlrInvert or agnCnfgAlrFilter to 'yes'(or yesAndSave for Mask) will add this new entry to the table. Setting for an existing entry agnCnfgAlrMask/ agnCnfgAlrInvert/agnCnfgAlrFilter (one or more) to 'no' (noAndSave for Mask) so that ALL these objects' values are 'no' , will delete this entry from the table. For agnCnfgAlrMask, only if [(last saved value=noAndSave) AND (new value is 'no' or 'noAndSave')] the object's value is considered 'no' for deleting the entry. For some products (like MP, MPH, Vmux2100) the Active Alarms are always part of the table and cannot be removed even if their Mask/Invert/Filter are No.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AgnCnfgAlrEntry

agnCnfgAlrEntry		1.3.6.1.4.1.164.3.1.2.2.8.2.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AgnCnfgAlrEntry

agnCnfgAlrCode		1.3.6.1.4.1.164.3.1.2.2.8.2.1.1
The alarm code. The following attributes refer this code.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnCnfgAlrSlot		1.3.6.1.4.1.164.3.1.2.2.8.2.1.2
The alarm slot. The following attributes apply for the alarm code and slot selected. all = the attributes apply to all slots. notApplicable = the selected alarm is for system level. For the Vmux2100 Main Board clA (3) is used.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	psA(1), psB(2), clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), all(200), notApplicable(255)

agnCnfgAlrPort		1.3.6.1.4.1.164.3.1.2.2.8.2.1.3
The alarm port. The following attributes apply for the alarm code,slot and port selected. 200 = all = the attributes apply to all ports of the selected slot. When selected Slot is 'all', only 'all' or 'notApplicable' are valid Port selections. notApplicable = the selected alarm is for system or card level. =255 for MP =100 for DXC - For MP: - valid cards' ports are: exPrt1(1)..exPrt16(16) inPrt1(101)..inPrt48 (148) - IP Bundles - For DXC, the port index will include the Slot, as for all DXC tables: [(IO Slot+10)&n] ; n=odd for external ports n=even for internal ports.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnCnfgAlrMask		1.3.6.1.4.1.164.3.1.2.2.8.2.1.4
An attribute defining the desired Mask state of an alarm . no - unmask (this command is not saved in agent's common database) noAndSave - unmask ; this command is saved in agent's common database yes - mask (this command is not saved in agent's common database) yesAndSave - mask ; this command is saved in agent's common database. Commands that are not saved, will be lost upon power-up or selected card removal.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), noAndSave(2), yes(3), yesAndSave(4)

agnCnfgAlrInvert		1.3.6.1.4.1.164.3.1.2.2.8.2.1.5
An attribute defining the desired Invert state of an alarm . no - not inverted. yes - inverted. For MP, it is not applicable for alarms that are currently OFF.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3)

agnCnfgAlrFilter		1.3.6.1.4.1.164.3.1.2.2.8.2.1.6
An attribute defining if Filter is desired for the alarm . no - no filter. yes - filter activate. This filter is activated within a window of time defined by agnCnfgAlrFilterWindow. Its purpose is to avoid frequent changes of an alarm between ON/OFF states.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3)

agnCnfgAlrFilterSet		1.3.6.1.4.1.164.3.1.2.2.8.2.1.7
This is a top threshold causing the alarm that passes it, to be declared Set (ON) at the end of the respective window of time. - For alarms defined by default as state alarms (minor,major) this value will be in [%]. - For alarms defined by default as events, this value will be an integer meaning how many times this event should appear at least, during the window in order to be considered ON. The maximum value will be 255. This value should be greater than the one of agnCnfgAlrFilterReset. Agents that do not support Alarms Filter, will return 0.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

agnCnfgAlrFilterReset		1.3.6.1.4.1.164.3.1.2.2.8.2.1.8
This is a bottom threshold causing the alarm that does not pass it, to be declared Reset (ON) at the end of the respective window of time. - For alarms defined by default as state alarms (minor,major) this value will be in [%]. - For alarms defined by default as events, this value will be an integer meaning how many times this event should appear at most, during the window, in order to be considered OFF. This value should be less than the one of agnCnfgAlrFilterSet. Agents that do not support Alarms Filter, will return 0.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

agnCnfgAlrSeverity		1.3.6.1.4.1.164.3.1.2.2.8.2.1.9
An attribute defining desired severity of an alarm code per slot/port
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	event(3), minor(4), major(5), warning(6), critical(7)

agnCnfgAlrReportTable		1.3.6.1.4.1.164.3.1.2.2.8.3
This table enables the user to configure the desired Alarm Reports according to alarms severity.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AgnCnfgAlrReportEntry

agnCnfgAlrReportEntry		1.3.6.1.4.1.164.3.1.2.2.8.3.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AgnCnfgAlrReportEntry

agnCnfgAlrReportType		1.3.6.1.4.1.164.3.1.2.2.8.3.1.1
The alarm report type. trap - traps will be sent only for alarms having the selected On/Off severity or higher. buffer - only alarms having the selected On/Off severity and higher, will be reported to the buffer. relay - relay contact will be activated only for alarms having the selected On severity or higher. For products having 2 relays, this is the R1 Relay. alrLedOn/alrLedBlink - user should select a higher severity (ReportOn) for alrLedBlink than for alrLedOn (Blinking Led means a more severe alarm than steady ON Led). alrLedOn - MTCL-1 Alarm Led will be ON only when agnSAlrStatusAll equals the selected severity or higher, but lower severity than that selected for 'alrLedBlink'. For products having 2 LEDs, this is the Minor LED. alrLedBlink - MTCL-1 Alarm Led will Blink only when agnSAlrStatusAll equals the selected severity or higher. For products having 2 LEDs, this is the Major LED. relay2 - relay 2 contact will be activated only for alarms having the selected On severity or higher. This is the R2 Relay.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	trap(1), buffer(2), relay(3), alrLedOn(4), alrLedBlink(5), relay2(6)

agnCnfgAlrStartReportOn		1.3.6.1.4.1.164.3.1.2.2.8.3.1.2
This object specifies the severity from which alarms will be reported. Alarms having this severity or higher, will be reported. This object specifies the report severity only for alarms that turn to ON state. noReport - no Report at all (for any severity).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noReport(2), event(3), minor(4), major(5), warning(6), critical(7)

agnCnfgAlrStartReportOff		1.3.6.1.4.1.164.3.1.2.2.8.3.1.3
This object specifies the severity from which alarms will be reported. Alarms having this severity or higher, will be reported. This object specifies the report severity only for alarms that turn to OFF state. notApplicable - for 'relay','alrLedOn','alrLedBlink', 'relay2' report types, in MP. noReport - no Report at all (for any severity).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), noReport(2), event(3), minor(4), major(5), warning(6), critical(7)

agnCOffsetCmd		1.3.6.1.4.1.164.3.1.2.2.9
An object defining special user request. notApplicable - is RO value for products that do not support this object. normal - nothing special u1 - user 1 - for all Voice cards, the DISPLAYED Tx and Rx Levels will have the following Offsets: - 2 Wires port: Tx Level: the base value (for 0dBm) = 0 Rx Level: the base value (for 0dBm) = -2 - 4 Wires port: Tx Level: the base value (for 0dBm) = -16 Rx Level: the base value (for 0dBm) = 7 The MIB and application DB will use the values without Offset.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), normal(2), u1(3)

agnCT1E1RingTable		1.3.6.1.4.1.164.3.1.2.2.10
Configuration of all T1/E1 Ring ML cards and ports. The write operation into the table objects is valid only for the TmpCnfg. A Slot/Port that does not participate in the T1/E1 Ring, will not exist in this table. A ML port that exists in this table, cannot exist at the same time in the IO Redundancy table (sysCRdnTable).
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AgnCT1E1RingEntry

agnCT1E1RingEntry		1.3.6.1.4.1.164.3.1.2.2.10.1
An Entry in table agnCT1E1RingTable
Status: current	Access: not-accessible
OBJECT-TYPE
	AgnCT1E1RingEntry

agnCT1E1RingCnfgIdx		1.3.6.1.4.1.164.3.1.2.2.10.1.1
This object indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnCT1E1RingPrimeSlot		1.3.6.1.4.1.164.3.1.2.2.10.1.2
The slot number of the Primary card of the Ring Pair.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

agnCT1E1RingPrimePort		1.3.6.1.4.1.164.3.1.2.2.10.1.3
The port number in the Primary Card. For external ports, the value will be as that of the port in the card. Example: external-3 -> 3 external-4 -> 4 For internal ports, the value will be 100 + the port in the card. Example: internal-1 -> 101 internal-4 -> 104
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnCT1E1RingSecSlot		1.3.6.1.4.1.164.3.1.2.2.10.1.4
The slot number of the Secondary card of the Ring Pair.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

agnCT1E1RingSecPort		1.3.6.1.4.1.164.3.1.2.2.10.1.5
The port number in the Secondary Card. For external ports, the value will be as that of the port in the card. Example: external-3 -> 3 external-4 -> 4 For internal ports, the value will be 100 + the port in the card. Example: internal-1 -> 101 internal-4 -> 104
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

agnCT1E1RingRecTime		1.3.6.1.4.1.164.3.1.2.2.10.1.6
T1/E1 Ring Recovery Time (sec). Valid Values: 1..99, 65535. 65535=NA.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

agnCT1E1RingRowStatus		1.3.6.1.4.1.164.3.1.2.2.10.1.7
This parameter allows NMS to create/delete entries of this table. The only possible supported RowStatus vaules are active (1) and destroy (6).
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

agnCT1E1RingWTR		1.3.6.1.4.1.164.3.1.2.2.10.1.8
T1/E1 Ring Wait to Restore (sec). Valid Values: 0..999, 65535. 65535=NA. When the value <> 65535, the value of agnCT1E1RingRecTime must be 65535.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

agnCT1E1RingDualFailDetection		1.3.6.1.4.1.164.3.1.2.2.10.1.9
T1/E1 Ring - Dual Failure Detection enable/disable.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disable(2), enable(3)

agnCMainExitPort		1.3.6.1.4.1.164.3.1.2.2.11
An object defining the Main Exit Port for the Data of the device. In the Vmux-120 Device the Data can Exit via one of the 2 existing ports: 1. Ethernet port (2) 2. A port that can be E1 or T1 or a Serial Link (3).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), eth(2), e1T1SerialLink(3)

agnCBuMlTable		1.3.6.1.4.1.164.3.1.2.2.12
Configuration for Primary, Secondary and Third Link. These are used for Link Backup.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AgnCBuMlEntry

agnCBuMlEntry		1.3.6.1.4.1.164.3.1.2.2.12.1
An Entry in table agnCBuMlTable
Status: current	Access: not-accessible
OBJECT-TYPE
	AgnCBuMlEntry

agnCBuMlCnfgIdx		1.3.6.1.4.1.164.3.1.2.2.12.1.1
This object indicates the Index of the Configuration database (1..255) being accessed. Index of 255 relates to the Temporary Configuration.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

agnCBuMlRole		1.3.6.1.4.1.164.3.1.2.2.12.1.2
The Role of the Link. Primary Link is the Link that should usually work. If the Primary Link fails, the data will go through the Secondary Link. If both Primary and Secondary Links fail, the data will go through the Third Link, provided it is up.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	primary(2), secondary(3), third(4), fourth(5)

agnCBuMlType		1.3.6.1.4.1.164.3.1.2.2.12.1.3
The Type of the Link. For E1/T1 the Link can be Link A - e1T1a or Link B - e1T1b.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(2), e1T1a(3), e1T1b(4), eth(5)

agnCBuMlDefaultGateway		1.3.6.1.4.1.164.3.1.2.2.12.1.4
Default Gateway's IP Address.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

agnCBuMlSubnetMask		1.3.6.1.4.1.164.3.1.2.2.12.1.5
The Link subnet mask.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

agnCBuMlOamFrequency		1.3.6.1.4.1.164.3.1.2.2.12.1.6
Time in sec. between 2 OAM packets.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

agnCBuMlOamTimeoutCycles		1.3.6.1.4.1.164.3.1.2.2.12.1.7
No. of cycles the Link will send OAM packets without receiving a response from the remote Link before switching to the Backup Link.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

agnCBuMlWaitToRestore		1.3.6.1.4.1.164.3.1.2.2.12.1.8
This object defines traffic recovery time (in milliseconds) of the link after its recovery. This object is applicable only when Recovery Mode is revertive.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

agnCQ50Table		1.3.6.1.4.1.164.3.1.2.2.13
Table for the device Q50 parameters. Q50 is a Signaling protocol used between PBX devices. It is possible to control the initiation of calls using Q.50. This is useful for devices when there is a congestion.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AgnCQ50Entry

agnCQ50Entry		1.3.6.1.4.1.164.3.1.2.2.13.1
An Entry in table agnCQ50Table
Status: current	Access: not-accessible
OBJECT-TYPE
	AgnCQ50Entry

agnCQ50CnfgIdx		1.3.6.1.4.1.164.3.1.2.2.13.1.1
This object indicates the Index of the Configuration database (1..255) being accessed. Index of 255 relates to the Temporary Configuration.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

agnCQ50StopCallsThresh		1.3.6.1.4.1.164.3.1.2.2.13.1.2
This object indicates the Bandwidth Threshold percent (%) above which new Calls from the PBX will be disabled.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

agnCQ50DiscardPktThresh		1.3.6.1.4.1.164.3.1.2.2.13.1.3
This object indicates the Bandwidth Threshold percent (%) above which voice packets will be discarded. Usually, the value selected should be higher than the value of agnCQ50StopCallsThresh.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

agnCQ50BlockNewModemVbdCallsThresh		1.3.6.1.4.1.164.3.1.2.2.13.1.4
This object indicates the Modem VBD Calls Threshold percent (%) above which new modem calls will be rejected.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

agnCQ50BlockNewModemRelayCallsThresh		1.3.6.1.4.1.164.3.1.2.2.13.1.5
This object indicates the Modem Relay Calls Threshold percent (%) above which new modem calls will be rejected.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

agnCmprTable		1.3.6.1.4.1.164.3.1.2.3.1
A table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AgnCmprEntry

agnCmprEntry		1.3.6.1.4.1.164.3.1.2.3.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AgnCmprEntry

agnCmprTypIdx		1.3.6.1.4.1.164.3.1.2.3.1.1.1
This attribute indicates the Type of the Compressed being referred.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnCmprCnfgIdx		1.3.6.1.4.1.164.3.1.2.3.1.1.2
This attribute indicates the configuration to which the Compressed information is related.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnCmprVersion		1.3.6.1.4.1.164.3.1.2.3.1.1.3
This attribute indicates the version of the internal format of the Compressed data
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnCmprObj		1.3.6.1.4.1.164.3.1.2.3.1.1.4
This attribute is the compressed information itself.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

agnDlciCmprTable		1.3.6.1.4.1.164.3.1.2.3.2
A table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AgnDlciCmprEntry

agnDlciCmprEntry		1.3.6.1.4.1.164.3.1.2.3.2.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AgnDlciCmprEntry

agnDlciCmprCnfgIdx		1.3.6.1.4.1.164.3.1.2.3.2.1.1
This attribute indicates the configuration to which the Compressed information is related.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnDlciCmprVersion		1.3.6.1.4.1.164.3.1.2.3.2.1.2
This attribute indicates the version of the internal format of the Compressed data
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnDlciCmprDlciIdx		1.3.6.1.4.1.164.3.1.2.3.2.1.3
This attribute indicates a unique identifier of the Dlci, the compressed information relates to. The values are between 16 - 991.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnDlciCmprObj		1.3.6.1.4.1.164.3.1.2.3.2.1.4
This attribute is the compressed information itself.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

agnAlarmsCmprTable		1.3.6.1.4.1.164.3.1.2.3.3
A table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AgnAlarmsCmprEntry

agnAlarmsCmprEntry		1.3.6.1.4.1.164.3.1.2.3.3.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AgnAlarmsCmprEntry

agnAlarmsCmprVersion		1.3.6.1.4.1.164.3.1.2.3.3.1.1
This attribute indicates the version of the internal format of the Compressed data
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnAlarmsCmprAlarmIdx		1.3.6.1.4.1.164.3.1.2.3.3.1.2
A unique number to identify an entry in the alarm status table of the agent.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnAlarmsCmprObj		1.3.6.1.4.1.164.3.1.2.3.3.1.3
This attribute is the compressed information itself.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

agnAlrBufCmprTable		1.3.6.1.4.1.164.3.1.2.3.4
A table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AgnAlrBufCmprEntry

agnAlrBufCmprEntry		1.3.6.1.4.1.164.3.1.2.3.4.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AgnAlrBufCmprEntry

agnAlrBufCmprVersion		1.3.6.1.4.1.164.3.1.2.3.4.1.1
This attribute indicates the version of the internal format of the Compressed data
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnAlrBufCmprAlarmIdx		1.3.6.1.4.1.164.3.1.2.3.4.1.2
A unique number to identify an entry in the history alarms buffer of the agent.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnAlrBufCmprObj		1.3.6.1.4.1.164.3.1.2.3.4.1.3
This attribute is the compressed information itself.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

agnSCmprErrListTable		1.3.6.1.4.1.164.3.1.2.3.5
A table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AgnSCmprErrListEntry

agnSCmprErrListEntry		1.3.6.1.4.1.164.3.1.2.3.5.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AgnSCmprErrListEntry

agnSCmprErrVersion		1.3.6.1.4.1.164.3.1.2.3.5.1.1
The version of the compressed data
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnSCmprErrIdx		1.3.6.1.4.1.164.3.1.2.3.5.1.2
Unique number to identify an entry in the errors list table. The maximum entry value cannot exceed the value of 'agnSNoOfSanityCheckErr'.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnSCmprErrObj		1.3.6.1.4.1.164.3.1.2.3.5.1.3
This attribute is a full text description of the error, including: error code, slot and port numbers related to the code .
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

agnTsCmprTable		1.3.6.1.4.1.164.3.1.2.3.6
A table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AgnTsCmprEntry

agnTsCmprEntry		1.3.6.1.4.1.164.3.1.2.3.6.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AgnTsCmprEntry

agnTsCmprVerIdx		1.3.6.1.4.1.164.3.1.2.3.6.1.1
This object indicates the version of the internal format of the Compressed data.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnTsCmprCnfgIdx		1.3.6.1.4.1.164.3.1.2.3.6.1.2
This object indicates the configuration to which the Compressed information is related. 255=temporary configuration. Set can be performed only to the temporary configuration.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnTsCmprSlotIdx		1.3.6.1.4.1.164.3.1.2.3.6.1.3
This object indicates the Slot to which the Compressed information is related. For MP-2100: IO-1..IO-12 = (5).. (16) For DXC-30 : IO-1..IO-15 = (5).. (19). NA=255.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnTsCmprPortIdx		1.3.6.1.4.1.164.3.1.2.3.6.1.4
This object indicates the Port within the Slot, to which the Compressed information is related. For Port Index see each product's spec.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnTsCmprPduIdx		1.3.6.1.4.1.164.3.1.2.3.6.1.5
This object indicates the PDU index within the same port. That provides for the case when one PDU is not sufficient for all TS Assignment data of the same port.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnTsCmprData		1.3.6.1.4.1.164.3.1.2.3.6.1.6
This object is the compressed information itself. It provides information about all TSs of a port.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

agnXCmprTable		1.3.6.1.4.1.164.3.1.2.3.7
A table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AgnXCmprEntry

agnXCmprEntry		1.3.6.1.4.1.164.3.1.2.3.7.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AgnXCmprEntry

agnXCmprTypIdx		1.3.6.1.4.1.164.3.1.2.3.7.1.1
This attribute indicates the Type of the Compressed being referred. One of the types is V5.1 Variant data.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnXCmprVersion		1.3.6.1.4.1.164.3.1.2.3.7.1.2
This attribute indicates the version of the internal format of the Compressed data.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnXCmprIdx3		1.3.6.1.4.1.164.3.1.2.3.7.1.3
3rd index - can be used for any purpose according to the agnXCmprTypIdx. Example: for V5.1 Variant, this attribute indicates the configuration to which the Compressed information is related. 255=temporary configuration. Set can be performed only to the temporary configuration.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnXCmprIdx4		1.3.6.1.4.1.164.3.1.2.3.7.1.4
4th index - can be used for any purpose according to the agnXCmprTypIdx. Example: for V5.1 Variant,this attribute indicates a unique number of the slot position where the card is inserted. Valid values: psA(1),psB(2),clA(3),clB(4),io1(5)..io12(16); notApplicable=255.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnXCmprIdx5		1.3.6.1.4.1.164.3.1.2.3.7.1.5
5th index - can be used for any purpose according to the agnXCmprTypIdx. Example: for V5.1 Variant,this attribute indicates a unique identifier of the port the compressed information relates to. Valid values: exPrt1 (1) .. exPrt12 (12) , inPrt1 (101) .. inPrt48 (148).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnXCmprIdx6		1.3.6.1.4.1.164.3.1.2.3.7.1.6
6th index - can be used for any purpose according to the agnXCmprTypIdx. Example: for V5.1 Variant,this attribute indicates the Variant index. Valid values are: 0..127, 255 (= temp cnfg).Set can be performed only to the temporary configuration.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnXCmprIdx7		1.3.6.1.4.1.164.3.1.2.3.7.1.7
7th index - can be used for any purpose according to the agnXCmprTypIdx. Example: for V5.1 Variant,this attribute is not needed. Therefore, its value will be always 255=notApplicable.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnXCmprObj		1.3.6.1.4.1.164.3.1.2.3.7.1.8
This attribute is the compressed information itself.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

agnLinkMapTable		1.3.6.1.4.1.164.3.1.5.1
A table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AgnLinkMapEntry

agnLinkMapEntry		1.3.6.1.4.1.164.3.1.5.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AgnLinkMapEntry

mapLinkId		1.3.6.1.4.1.164.3.1.5.1.1.1
A unique identifier of the link
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

mapLinkSltIdx		1.3.6.1.4.1.164.3.1.5.1.1.2
This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries clA(3), io6(10)..io12(16) are not valid.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noConnect(2), clA(3), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

mapLinkPrtIdx		1.3.6.1.4.1.164.3.1.5.1.1.3
This attribute indicates a unique port number.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), exPrt5(5), exPrt6(6), exPrt7(7), exPrt8(8), exPrt9(9), exPrt10(10), exPrt11(11), exPrt12(12), noConnect(100), inPrt1(101), inPrt2(102), inPrt3(103), inPrt4(104), inPrt5(105), inPrt6(106), inPrt7(107), inPrt8(108), inPrt9(109), inPrt10(110), inPrt11(111), inPrt12(112)

mapLinkStatus		1.3.6.1.4.1.164.3.1.5.1.1.4
This attribute indicates the status of the link between the two muxes
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), down(2), up(3)

alrBufTable		1.3.6.1.4.1.164.3.1.2.4.1
A table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlrBufEntry

alrBufEntry		1.3.6.1.4.1.164.3.1.2.4.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AlrBufEntry

alrBufIdx		1.3.6.1.4.1.164.3.1.2.4.1.1.1
This attribute indicates a unique number to identify this entry
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

alrBufDescription		1.3.6.1.4.1.164.3.1.2.4.1.1.2
This entry is a unique text description of the alarm in the buffer. The alarm description includes the following information: alarm code, slot id, card type, channel id , alarm text, alarm status, masked flag and event counter
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

alrBufCode		1.3.6.1.4.1.164.3.1.2.4.1.1.3
A code identifying the alarm of an entry in the alarm buffer table.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

alrBufSlot		1.3.6.1.4.1.164.3.1.2.4.1.1.4
The slot number this alarm refers to. When the alarm refers to a system alarm, the value will be 'notApplicable(255)'.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	psA(1), psB(2), clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), notApplicable(255)

alrBufPort		1.3.6.1.4.1.164.3.1.2.4.1.1.5
The port number this alarm refers to. If the port number is irrelevant to this alarm (if it is a system/card level alarm) the value will be 9999.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

alrBufSeverity		1.3.6.1.4.1.164.3.1.2.4.1.1.6
The severity of the alarm.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	event(3), minor(4), major(5), warning(6), critical(7)

alrBufState		1.3.6.1.4.1.164.3.1.2.4.1.1.7
State of the alarm (On/Off).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), on(3)

alrBufferClearCmd		1.3.6.1.4.1.164.3.1.2.4.2
Setting this attribute to ON, will enforce a clear operation on the Alarms Buffer. Upon completion, the value will automatically change to off(2). For MP-2100/2200, this command will not really erase the Alarm Buffer, but is only an ACK of seeing the Buffer. It marks a pointer of the last entry's alrBufIdx, in order to allow view of new alarms entered after this pointer (alrBufIdxUponLastAck).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

alrBufIdxUponLastAck		1.3.6.1.4.1.164.3.1.2.4.3
This attribute indicates the value of alrBufIdx for the last existing entry of alrBufTable, when alrBufferClearCmd was last Set to on(3). That will enable a user to see only Alarms that entered the alrBufTable after last Set of alrBufferClearCmd, by GetNext of alrBufDescription with this index.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

agnCAgendaTable		1.3.6.1.4.1.164.3.1.2.5.1
This table devides the week days into categories needed for DB flip consideration.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AgnCAgendaEntry

agnCAgendaEntry		1.3.6.1.4.1.164.3.1.2.5.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AgnCAgendaEntry

agnCAgendaCnfgIdx		1.3.6.1.4.1.164.3.1.2.5.1.1.1
Active or Temporary Agenda Table. Both configurations can be read but only the Temporary can be written to.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	active(1), temporary(255)

agnCAgendaDayIdx		1.3.6.1.4.1.164.3.1.2.5.1.1.2
Day of week
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	sunday(1), monday(2), tuesday(3), wednesday(4), thursday(5), friday(6), saturday(7)

agnCAgendaDayCategory		1.3.6.1.4.1.164.3.1.2.5.1.1.3
The Category of the Day
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	fullWorkday(1), partialWorkday(2), weekend(3)

agnCFlipNetEventsTable		1.3.6.1.4.1.164.3.1.2.5.2
This table holds the Net Events the MUX should trace
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AgnCFlipNetEventsEntry

agnCFlipNetEventsEntry		1.3.6.1.4.1.164.3.1.2.5.2.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AgnCFlipNetEventsEntry

agnCFlipNetEventsCnfgIdx		1.3.6.1.4.1.164.3.1.2.5.2.1.1
Active or Temporary Net Events Table. Both configurations can be read but only the Temporary can be written to.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	active(1), temporary(255)

agnCFlipNetEventIdx		1.3.6.1.4.1.164.3.1.2.5.2.1.2
Entry within the table
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..10

agnCFlipNetEventActive		1.3.6.1.4.1.164.3.1.2.5.2.1.3
Indicates if the entry is valid. In order to Add/Modify parameters of an entry, this object should be set to Yes. In order to delete an entry, this object should be Set to No.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3)

agnCFlipNetEventType		1.3.6.1.4.1.164.3.1.2.5.2.1.4
The Net Event type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	time(1), linkDown(2), congestion(3)

agnCFlipNetEventNo		1.3.6.1.4.1.164.3.1.2.5.2.1.5
The Net Event No. (Bit Index)
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..512

agnCFlipNetEventSlot		1.3.6.1.4.1.164.3.1.2.5.2.1.6
The slot to which the net event relates . Not applicable for time event
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

agnCFlipNetEventPort		1.3.6.1.4.1.164.3.1.2.5.2.1.7
The port within the relevant slot. Valid values: - extPrt1(1)..exPrt16(16) - notApplicable(100) - inPrt1(101)..inPrt84(184)
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

agnCFlipNetEventISD		1.3.6.1.4.1.164.3.1.2.5.2.1.8
The time in seconds since the Net Event was reported as ON until it is considered as ON. Not relevant for time events.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..999

agnCFlipNetEventOSD		1.3.6.1.4.1.164.3.1.2.5.2.1.9
The time in seconds since the net event was reported as OFF until it is considered as OFF. Not relevant for time events.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..999

agnCFlipNetEventDayType		1.3.6.1.4.1.164.3.1.2.5.2.1.10
The time event relates to all days defined in this category in the agnCAgendaTable. Applicable only for time event
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), fullWorkday(2), partialWorkday(3), weekend(4)

agnCFlipNetEventStartTime		1.3.6.1.4.1.164.3.1.2.5.2.1.11
The time event will be activated at this time. The format is hh:mm.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(5)

agnCFlipNetEventEndTime		1.3.6.1.4.1.164.3.1.2.5.2.1.12
The time event will be deactivated at this time. The format is hh:mm.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(5)

agnCFlipTable		1.3.6.1.4.1.164.3.1.2.5.3
The DB Flip Decisions Table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AgnCFlipEntry

agnCFlipEntry		1.3.6.1.4.1.164.3.1.2.5.3.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AgnCFlipEntry

agnCFlipCnfgIdx		1.3.6.1.4.1.164.3.1.2.5.3.1.1
Active or Temporary Flip Decisions Table. Both configurations can be read but only the Temporary can be written to.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	active(1), temporary(255)

agnCFlipIdx		1.3.6.1.4.1.164.3.1.2.5.3.1.2
Entry number within the table
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..10

agnCFlipActive		1.3.6.1.4.1.164.3.1.2.5.3.1.3
Indicates if the entry is valid. In order to Add/Modify parameters of an entry this object should be Set to Yes. In order to delete an entry, this object should be Set to No.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3)

agnCFlipLogicalExp		1.3.6.1.4.1.164.3.1.2.5.3.1.4
A logical expression composed of events numbers (which were configured in the 'AgnCFlipNetEvantsTable') and logical operators ('|', '&', '!', '(', ')') between them. e.g - (1 & !2) | (121 & 230)
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(1..20)

agnCFlipDbNo		1.3.6.1.4.1.164.3.1.2.5.3.1.5
The ID of the required DB
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..10

agnCFlipDiscardDe		1.3.6.1.4.1.164.3.1.2.5.3.1.6
Indicates whether the Mux should start discarding all DE. (MP3000 Only).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), no(2), yes(3)

agnFlipDbControls		1.3.6.1.4.1.164.3.1.2.5.4
OBJECT IDENTIFIER

agnCFlipDbSanityCheckCmd		1.3.6.1.4.1.164.3.1.2.5.4.1
Setting this attribute to on(3) will initiate the process of Sanity check on the Temp Flip Db and automatically be changed to off(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

agnCSaveFlipDbCmd		1.3.6.1.4.1.164.3.1.2.5.4.2
Setting this attribute to on(3) will initiate the process of Sanity check on the Temp Flip Db and if it is OK, it will save the Flip Db in the NVRAM, activating the new Flip DB . If check detects errors, the save will not be performed. Afterwards, the object's value will change automatically to off(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

agnCSaveNetCnfgIdxCmd		1.3.6.1.4.1.164.3.1.2.5.4.3
This attribute specifies the Id of the target NVRAM Cnfg to which the TmpCnfg should be transferred. Upon set command the MUX will initiate the Sanity-Check process first. If successful, the actual transfer will be performed. If warnings are detected, the user will have to perform the command again to confirm the operation. Setting this object a second time to the same value without performing any change in the database, will cause the result: agnSSanityCheckStatus = unknown. This attribute doesn't cause actual Flip.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..10

agnCSaveNetFlipDbCmd		1.3.6.1.4.1.164.3.1.2.5.4.4
Setting this attribute to on(3) will save the Temp Flip DB Into the NVRAM without actual flip.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

agnCNetGoCmd		1.3.6.1.4.1.164.3.1.2.5.4.5
Setting this attribute to On will broadcast a 'GO' command to the network. When a Mux receives a 'GO' command it issues a delay for 'agnCNetDelay' seconds and then activates the DB which was pre-defined by one of the commands : 'agnCSaveNetCnfgIdxCmd' or 'agnCSaveNetFlipDbCmd'.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

agnCNetDelay		1.3.6.1.4.1.164.3.1.2.5.4.6
This attribute determines the period of time in seconds that takes for a message to be transferred over all the network. After a 'GO' command the MUX issues a delay of 'agnCNetDelay' before activating the appropriate DB. The delay will be applied only after performing agnCSaveFlipDbCmd.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..999

agnCNetEventsBcast		1.3.6.1.4.1.164.3.1.2.5.4.7
This object determines if the Net Events will be Broadcasted to other Muxes of the Net or not. disabled - Net Events will NOT be Broadcasted enabled - Net Events will be Broadcasted. Default=disabled. The value will be applied only after performing agnCSaveFlipDbCmd.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(2), enabled(3)

agnCNetEventsBcastInterval		1.3.6.1.4.1.164.3.1.2.5.4.8
When agnCNetEventsBcast is enabled, this object determines the interval of time in seconds, between two consecutive Net Events transferred over the network. Default=40 sec. The interval will be applied only after performing agnCSaveFlipDbCmd.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	10..60

agnSaSwchStatus		1.3.6.1.4.1.164.3.1.2.6.1
This object indicates the status of the switches on the stand-alone unit. Each switch is represented by a bit. The status is a sum of 2**n, according to the bits: bit 0 NMS (LSB) bit 1 Terminal '1' = forces the DCE to be terminal with Rate=9600bps, Data bits=8, Stop bits=1 bit 2 Xray bit 3 SW-Load '1' = when SW is loaded bit 4 DBS Default of all bits=0 When the status of these switches is unknown, the value of this object is 255.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnListDecodingTable		1.3.6.1.4.1.164.3.1.2.7.1
A decoding table . For each type of list, a description is given for each existing code.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AgnListDecodingEntry

agnListDecodingEntry		1.3.6.1.4.1.164.3.1.2.7.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AgnListDecodingEntry

agnListDecodingType		1.3.6.1.4.1.164.3.1.2.7.1.1.1
The type of list the decoding data refers to. alr - Alarms list sanity - Sanity Check Error list. counter - Counter type of ifPerfCounterType
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	alr(1), sanity(2), counter(3)

agnListDecodingCode		1.3.6.1.4.1.164.3.1.2.7.1.1.2
The specific code for which decoding is needed.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnListDecodingDescription		1.3.6.1.4.1.164.3.1.2.7.1.1.3
The description fitting the specific code and type of list required.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

agnListDecodingDefState		1.3.6.1.4.1.164.3.1.2.7.1.1.4
This object is applicable only for agnListDecodingType=alr. It reports the default state/severity of each alarm. User can change the severity of the alarms defined by this default via the agnListDecodingSeverity object.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), event(3), minor(4), major(5), warning(6), critical(7)

agnListDecodingSeverity		1.3.6.1.4.1.164.3.1.2.7.1.1.5
This object is applicable only for agnListDecodingType=alr. It enables the user to select a severity for each alarm. The severity is set per alarm code (same for all slots/ports using this code). event - can be set only for an alarm that is defined by default as 'event'. User can change the severity of the alarms defined by default as minor or major. The severity of an event may be set to another severity, but the change will actually happen only if the event threshold is active and passed the Set/ON condition. An event alarm that passed the threshold and changed its severity, will return automatically to event severity when meeting its Reset/OFF condition.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), event(3), minor(4), major(5), warning(6), critical(7)

agnListDecodingAcmRelaySlt		1.3.6.1.4.1.164.3.1.2.7.1.1.6
This object indicates the ACM slot, desired for outbound relay (report) for the selected alarm. In the ?004 Unit the entries io6(10)..io12(16) are not valid. none - when agnListDecodingType=alr AND the selected alarm should not be reported by an ACM card. notApplicable - when agnListDecodingType=sanity OR when [agnListDecodingType=alr and there is no ACM card installed in the Mux].
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

agnListDecodingAcmRelayPrt		1.3.6.1.4.1.164.3.1.2.7.1.1.7
This object indicates the ACM port within the slot, desired for outbound relay (report) for the selected alarm. notApplicable - when agnListDecodingType=sanity OR when agnListDecodingAcmRelaySlt=notApplicable.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), notApplicable(255)

agnDlciTable		1.3.6.1.4.1.164.3.1.2.8.1
The write operation into the Table Objects is valid only to the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AgnDlciEntry

agnDlciEntry		1.3.6.1.4.1.164.3.1.2.8.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AgnDlciEntry

agnDlciCnfgIdx		1.3.6.1.4.1.164.3.1.2.8.1.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

agnDlciLSltIdx		1.3.6.1.4.1.164.3.1.2.8.1.1.2
This attribute indicates a unique slot position where the card is inserted. This is the Source Slot of the DLCI. vs=Voice Switching In the ?004 Unit the entries io6(10)..io16) are not valid. For ISDN BRI ports of MX300/30 units: io1(5) = isdn1(5) and io2(6) = isdn2(6) LSlotIdx is defined according one of the following possiblities: 1. LSlotIdx is < HSlotIdx. 2. LSlotIdx is = HSlotIdx and LPrtIdx is < HPrtIdx. 3. LSlotIdx is = HSlotIdx and LPrtIdx is = HPrtIdx but LIdx is < HIdx.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	cl(3), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), vs(254), notApplicable(255)

agnDlciLPrtIdx		1.3.6.1.4.1.164.3.1.2.8.1.1.3
This attribute indicates a unique external or internal port number, including linkSelector or encapsulator. This is the Source Port of the DLCI. 100=noConnect (for voice switching) LPrtIdx is defined according one of the following possiblities: 1. LSlotIdx is < HSlotIdx. 2. LSlotIdx is = HSlotIdx and LPrtIdx is < HPrtIdx. 3. LSlotIdx is = HSlotIdx and LPrtIdx is = HPrtIdx but LIdx is < HIdx.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnDlciLIdx		1.3.6.1.4.1.164.3.1.2.8.1.1.4
This attribute indicates a unique index for each possible used DLCI(16..991). This is the Source Side of the DLCI. 0=notApplicable (for voice switching) LIdx is defined according one of the following possiblities: 1. LSlotIdx is < HSlotIdx. 2. LSlotIdx is = HSlotIdx and LPrtIdx is < HPrtIdx. 3. LSlotIdx is = HSlotIdx and LPrtIdx is = HPrtIdx but LIdx is < HIdx.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..991

agnDlciHSltIdx		1.3.6.1.4.1.164.3.1.2.8.1.1.5
This attribute indicates a unique slot position In the Mux where the DLCI is routed to - Destination Slot. For ISDN BRI ports of MX300/30 units: io1(5) = isdn1(5) and io2(6) = isdn2(6) In the ?004 Unit the entries io6(10)..io16) are not valid
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	cl(3), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

agnDlciHPrtIdx		1.3.6.1.4.1.164.3.1.2.8.1.1.6
This attribute indicates a unique port number where the DLCI is routed to - Destination Port.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnDlciHIdx		1.3.6.1.4.1.164.3.1.2.8.1.1.7
This attribute indicates a unique internal connection DLCI number where the Source DLCI is routed to - the Destination Side of the DLCI.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..991

agnDlciTxBc		1.3.6.1.4.1.164.3.1.2.8.1.1.8
This attribute indicates a unique Tx committed bandwidth on the user transmit line or at the port receive line.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	full(1), zero(2), txBc5100bps(3), txBc6400bps(4), txBc8300bps(5), txBc9600bps(6), txBc14400bps(7), txBc19200bps(8), txBc28800bps(9), txBc32000bps(10), txBc38400bps(11), txBc48000bps(12), txBc56000bps(13), txBc57600bps(14), txBc64Kbps(15), txBc128Kbps(16), txBc192Kbps(17), txBc256Kbps(18), txBc320Kbps(19), txBc384Kbps(20), txBc448Kbps(21), txBc512Kbps(22), txBc768Kbps(23), txBc896Kbps(24), txBc1024Kbps(25), txBc1152Kbps(26), txBc1280Kbps(27), txBc1344Kbps(28), txBc1472Kbps(29), txBc1600Kbps(30), txBc1728Kbps(31), txBc1856Kbps(32), txBc1920Kbps(33), txBc1984Kbps(34), txBc2048Kbps(35), txBc16000bps(36), txBc112Kbps(37), txBc168Kbps(38), txBc224Kbps(39), txBc336Kbps(40), txBc672Kbps(41), txBc1536Kbps(42), txBc1792Kbps(43)

agnDlciTxBe		1.3.6.1.4.1.164.3.1.2.8.1.1.9
This attribute indicates a unique Tx excess bandwidth on the user transmit line or at the port receive line.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	full(1), zero(2), txBe5100bps(3), txBe6400bps(4), txBe8300bps(5), txBe9600bps(6), txBe14400bps(7), txBe19200bps(8), txBe28800bps(9), txBe32000bps(10), txBe38400bps(11), txBe48000bps(12), txBe56000bps(13), txBe57600bps(14), txBe64Kbps(15), txBe128Kbps(16), txBe192Kbps(17), txBe256Kbps(18), txBe320Kbps(19), txBe384Kbps(20), txBe448Kbps(21), txBe512Kbps(22), txBe768Kbps(23), txBe896Kbps(24), txBe1024Kbps(25), txBe1152Kbps(26), txBe1280Kbps(27), txBe1344Kbps(28), txBe1472Kbps(29), txBe1600Kbps(30), txBe1728Kbps(31), txBe1856Kbps(32), txBe1920Kbps(33), txBe1984Kbps(34), txBe2048Kbps(35), txBe16000bps(36), txBe112Kbps(37), txBe168Kbps(38), txBe224Kbps(39), txBe336Kbps(40), txBe672Kbps(41), txBe1536Kbps(42), txBe1792Kbps(43)

agnDlciRxBc		1.3.6.1.4.1.164.3.1.2.8.1.1.10
This attribute indicates a unique Rx committed bandwidth on the user receive line or at the port transmit line.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	full(1), zero(2), rxBc5100bps(3), rxBc6400bps(4), rxBc8300bps(5), rxBc9600bps(6), rxBc14400bps(7), rxBc19200bps(8), rxBc28800bps(9), rxBc32000bps(10), rxBc38400bps(11), rxBc48000bps(12), rxBc56000bps(13), rxBc57600bps(14), rxBc64Kbps(15), rxBc128Kbps(16), rxBc192Kbps(17), rxBc256Kbps(18), rxBc320Kbps(19), rxBc384Kbps(20), rxBc448Kbps(21), rxBc512Kbps(22), rxBc768Kbps(23), rxBc896Kbps(24), rxBc1024Kbps(25), rxBc1152Kbps(26), rxBc1280Kbps(27), rxBc1344Kbps(28), rxBc1472Kbps(29), rxBc1600Kbps(30), rxBc1728Kbps(31), rxBc1856Kbps(32), rxBc1920Kbps(33), rxBc1984Kbps(34), rxBc2048Kbps(35), rxBc16000bps(36), rxBc112Kbps(37), rxBc168Kbps(38), rxBc224Kbps(39), rxBc336Kbps(40), rxBc672Kbps(41), rxBc1536Kbps(42), rxBc1792Kbps(43)

agnDlciRxBe		1.3.6.1.4.1.164.3.1.2.8.1.1.11
This attribute indicates a unique Rx excess bandwidth on the user receive line or at the port transmit line.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	full(1), zero(2), rxBe5100bps(3), rxBe6400bps(4), rxBe8300bps(5), rxBe9600bps(6), rxBe14400bps(7), rxBe19200bps(8), rxBe28800bps(9), rxBe32000bps(10), rxBe38400bps(11), rxBe48000bps(12), rxBe56000bps(13), rxBe57600bps(14), rxBe64Kbps(15), rxBe128Kbps(16), rxBe192Kbps(17), rxBe256Kbps(18), rxBe320Kbps(19), rxBe384Kbps(20), rxBe448Kbps(21), rxBe512Kbps(22), rxBe768Kbps(23), rxBe896Kbps(24), rxBe1024Kbps(25), rxBe1152Kbps(26), rxBe1280Kbps(27), rxBe1344Kbps(28), rxBe1472Kbps(29), rxBe1600Kbps(30), rxBe1728Kbps(31), rxBe1856Kbps(32), rxBe1920Kbps(33), rxBe1984Kbps(34), rxBe2048Kbps(35), rxBe16000bps(36), rxBe112Kbps(37), rxBe168Kbps(38), rxBe224Kbps(39), rxBe336Kbps(40), rxBe672Kbps(41), rxBe1536Kbps(42), rxBe1792Kbps(43)

agnDlciPriority		1.3.6.1.4.1.164.3.1.2.8.1.1.12
This attribute indicates a unique priority of the pcv. 1 is the lowest priority and 7 is the highest priority.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..8

agnDlciStatus		1.3.6.1.4.1.164.3.1.2.8.1.1.13
This attribute indicates the status of the pvc. The status is disconnected(1) when one of the sides is programmed as not connected
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	disconnected(1), connected(2)

agnDlciSpoofing		1.3.6.1.4.1.164.3.1.2.8.1.1.14
This object refers to sending of RIP messages: - yes : RIP messages will be sent ONLY if there is a change in the Net. - no : RIP messages will be always sent. This object is relevant only when one side of the DLCI is a CL-NMS interface. Default=no.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	no(2), yes(3)

agnDlciFunnelEnable		1.3.6.1.4.1.164.3.1.2.8.1.1.15
This object selects Funnel activation: - disabled: Funnel operation will be disabled. The agnDlciTxBe and agnDlciTxBc values are not used for funneling. - enabled : Funnel operation will be enabled both for Source and Destination of the DLCI. The agnDlciTxBe and agnDlciTxBc values are used for funneling calculations. - source: Funnel operation will be enabled only for the Source of the DLCI. - destination:Funnel operation will be enabled only for the Destination of the DLCI. This object is relevant only for an encapsulating DLCI. In case of a Link Selector DLCI, the agnDlciTxBe and agnDlciTxBc values are used for bandwidth of Link Selector. Default=disabled.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disabled(2), enabled(3), source(4), destination(5)

agnDlciRoutingProtocol		1.3.6.1.4.1.164.3.1.2.8.1.1.16
This object is relevant only when one side of the DLCI is a CL-NMS interface. It defines which Routing Protocol will be used for management via CL-NMS port. notApplicable will be used for all slots but CL. rip is a proprietary rip protocol. Default=rip.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notApplicable(1), rip(2), rip2(3), none(4)

agnDlciRowStatus		1.3.6.1.4.1.164.3.1.2.8.1.1.17
This attribute allows to create/delete a row in this table. For creating a row, the NMS should set agnRowStatus.255.id2.id3.id4.id5.id6.id7 = active(1). For destroying a row, the NMS should set: agnRowStatus.255.id2.id3.id4.id5.id6.id7 = destroy(6). Only rows with status active(1) are relevant. The only possible supported RowStatus vaules are active (1) and destroy (6).
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

agnVoiceSwConfTable		1.3.6.1.4.1.164.3.1.2.9.1
MXcess Configuration for Voice Switching.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AgnVoiceSwConfEntry

agnVoiceSwConfEntry		1.3.6.1.4.1.164.3.1.2.9.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AgnVoiceSwConfEntry

agnVoiceSwConfIdx		1.3.6.1.4.1.164.3.1.2.9.1.1.1
Active or Temporary Table. Both configurations can be read but only the Temporary can be written to.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	active(1), temporary(255)

agnVoiceSwConfZoneId		1.3.6.1.4.1.164.3.1.2.9.1.1.2
1 or 2 digits, (0-9)(1-9).
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(1..2)

agnVoiceSwConfNodeId		1.3.6.1.4.1.164.3.1.2.9.1.1.3
1, 2 or 3 digits, (1-9),(0-9),(0-9).
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(1..3)

agnVoiceSwConfNoOfHops		1.3.6.1.4.1.164.3.1.2.9.1.1.4
Number of hops the frame will go through the net before deciding to discard the frame (like time-to-live in IP). 0 = notApplicable Default=20 .
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..20

agnVoiceSwConfSidt		1.3.6.1.4.1.164.3.1.2.9.1.1.5
SIDT: Short Inter Digit Timeout used as timer (in sec.) between digits after routing is completed. The timeout indicates end of dialing and the call can then be setup. 0 = notApplicable Default=2 sec.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..30

agnVoiceSwConfLidt		1.3.6.1.4.1.164.3.1.2.9.1.1.6
LIDT: Long Inter Digit Timeout used as timer between digits before routing is completed. If no digits were dialed and LIDT expired then the user will get an error tone and the call will be disconnected. 0 = notApplicable Default=15 sec.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..30

agnVoiceSwConfDialPlan		1.3.6.1.4.1.164.3.1.2.9.1.1.7
This is the Dialing Plan method that will be used in the Voice Switching. Static Dialing Plan - Routing is defined by the current device Zone and Node ID in the Network. Static Dialing Plan Plus - Includes the Static Dialing Plan but contains an addition of defining the number of dialed digits. Flexible Dialing Plan - Routing is defined in a flexible form. In this plan the user can configure the extension number of a local voice channel, Route a call to a remote destination and enter the Number of Digits for a specific dial prefix.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	staticDialPlan(2), staticDialPlanPlus(3), flexDialPlan(4)

agnVoiceSwConfRtTable		1.3.6.1.4.1.164.3.1.2.9.2
Routing Table for Voice Switching.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AgnVoiceSwConfRtEntry

agnVoiceSwConfRtEntry		1.3.6.1.4.1.164.3.1.2.9.2.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AgnVoiceSwConfRtEntry

agnVoiceSwConfRtDbId		1.3.6.1.4.1.164.3.1.2.9.2.1.1
Active or Temporary Table. Both configurations can be read but only the Temporary can be written to.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	active(1), temporary(255)

agnVoiceSwConfRtIdx		1.3.6.1.4.1.164.3.1.2.9.2.1.2
The Index of the row.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnVoiceSwConfRtDigits		1.3.6.1.4.1.164.3.1.2.9.2.1.3
Dialed digits: Series of digits 0...9, '*', '#' or '%'. The '*' and '#' can have many uses according to the user's decision. For example, they can be used as part of the Dialed Number, they exist on the phone number panel. '*' can also be used instead of a series of numbers. The '%' means any digits (wildcard) and is used without a series of digits. When the agnVoiceSwConfRtAction is del (7), the series of digits that are configured via this MIB object will be deleted from the prefix of the dialed number.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(1..7)

agnVoiceSwConfRtAction		1.3.6.1.4.1.164.3.1.2.9.2.1.4
Action that the system should perform for the digits: agnVoiceSwConfRtDigits. The action that is allowed depends on the Dialing Plan. Here is the list of the allowed actions: For Static Dialing Plan - zone, node, in, shortDialing, hgr, del, rep For Static Dialing Plan Plus - zone, node, in, shortDialing, hgr, del, rep, numDigDP For Flexible Dialing Plan - hgr, del, rep, numDigDP, route, ext
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notApplicable(1), zone(2), node(3), shortDialing(4), in(5), hgr(6), del(7), rep(8), pri(9), bri(10), numDigDP(11), route(12), ext(13)

agnVoiceSwConfRtData		1.3.6.1.4.1.164.3.1.2.9.2.1.5
This field is relevant for actions hgr(6), and rep(8), numDigDP(11) and contains the following information: For hgr - the number of the Hunt Group. For rep - the number of digits to be replaced with. For numDigDP - the number of digits collected before establishing the call. 0 indicates no defined length. In this case SIDT will be used.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(1..7)

agnVoiceSwConfRtSlot		1.3.6.1.4.1.164.3.1.2.9.2.1.6
Routing Slot- Relevant for actions zone(2), node(3), shortDialing(4), route(12), ext(13).
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	noConnect(2), cl(3), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

agnVoiceSwConfRtPort		1.3.6.1.4.1.164.3.1.2.9.2.1.7
Routing Port- Relevant for actions zone(2), node(3), shortDialing(4), route(12), ext(13). 100=noConnect (for non-routing case).
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

agnVoiceSwConfRtDlci		1.3.6.1.4.1.164.3.1.2.9.2.1.8
Routing DLCI- Relevant for actions zone(2), node(3), shortDialing(4), route(12), ext(13). Valid values: 0=notApplicable (for non-routing case). 1, 16..991
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

agnVoiceSwConfRtRowStatus		1.3.6.1.4.1.164.3.1.2.9.2.1.9
Status of the row for creating/deleting entries in the table. The only possible supported RowStatus vaules are active (1), notInService (2), notReady(3), createAndGo(4), createAndWait(5) and destroy(6).
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

agnVoiceSwConfRtMaxCalls		1.3.6.1.4.1.164.3.1.2.9.2.1.10
Maximum no. of simultaneous voice calls that are allowed in the direction defined by the current entry. Default=0 (No Limit).
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

agnVoiceSwConfRtPriority		1.3.6.1.4.1.164.3.1.2.9.2.1.11
This attribute indicates a unique priority of the Voice Switching Route. 1 is the lowest priority and 7 is the highest priority. 0 means N/A
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

agnVoiceSwConfHGTable		1.3.6.1.4.1.164.3.1.2.9.5
Table of Hunt Groups.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AgnVoiceSwConfHGEntry

agnVoiceSwConfHGEntry		1.3.6.1.4.1.164.3.1.2.9.5.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AgnVoiceSwConfHGEntry

agnVoiceSwConfHGdbIdx		1.3.6.1.4.1.164.3.1.2.9.5.1.1
Active or Temporary Table. Both configurations can be read but only the Temporary can be written to.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	active(1), temporary(255)

agnVoiceSwConfHGIdx		1.3.6.1.4.1.164.3.1.2.9.5.1.2
For Vmux-300 devices - This object represents a combination of - Hunt Group number and Extension number OR - Port number and Extension number. For other devices (e.g. MXcess, MP-2100H) - There may be up to 10 Hunt Groups per MXcess. That's the index of the hunt group relevant to this row.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnVoiceSwConfHGConnect		1.3.6.1.4.1.164.3.1.2.9.5.1.3
This attribute indicates whether the hunt group should be considered in any of the mux algorithms.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3)

agnVoiceSwConfHGExt		1.3.6.1.4.1.164.3.1.2.9.5.1.4
This is the extension number of the hunt group. 0 is for not valid. The allowed range is 10 - 99.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..99

agnVoiceSwConfHGExtString		1.3.6.1.4.1.164.3.1.2.9.5.1.5
This is the extension string of the hunt group. This string is a combination of digits, * and #.
Status: current	Access: read-write
OBJECT-TYPE
	SnmpAdminString

agnVoiceSwConfHGUserParams		1.3.6.1.4.1.164.3.1.2.9.5.1.6
This object indicates the User's parameters.
Status: current	Access: read-write
OBJECT-TYPE
	SnmpAdminString

agnVoiceSwConfHGStatus		1.3.6.1.4.1.164.3.1.2.9.5.1.7
This object enables the user to create/delete entries in this table. Its usage for values (1)..(6) should be identical to RowStatus SYNTAX. notApplicable(255) - should be used when the table is static (i.e. whenever create/delete entries is not allowed).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	active(1), notInService(2), notReady(3), createAndGo(4), createAndWait(5), destroy(6), notApplicable(255)

agnSigProfileTable		1.3.6.1.4.1.164.3.1.2.10.1
- For products supporting more than one configuration, the write operation into the Table is valid only to the TmpCnfg entry. - For products that do not support configurations, the write operation into the Table will be to agnSigProfileCnfgIdx=1. The table includes signaling profile parameters for Legacy Profiles.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AgnSigProfileEntry

agnSigProfileEntry		1.3.6.1.4.1.164.3.1.2.10.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AgnSigProfileEntry

agnSigProfileCnfgIdx		1.3.6.1.4.1.164.3.1.2.10.1.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. For products supporting more than one configuration,the write operation is valid only to the TmpCnfg. For Gmux2000 the range limitation (1..255) was discarded since the Idx is computed as: x 1000 + 255.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

agnSigProfileIdx		1.3.6.1.4.1.164.3.1.2.10.1.1.2
This attribute indicates the Signaling Profile (1..5). For MP-104/204, only Profile=1 will exist.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..5

agnSigProfileRxTx		1.3.6.1.4.1.164.3.1.2.10.1.1.3
This attribute indicates if the following objects refer to: Rx or Tx translation. Rx : ML->IO Tx : IO->ML . For MP-104/204, that means: Rx : Signaling to FXS CH Tx : Signaling to E1 Link.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	rx(1), tx(2)

agnSigProfileABCD		1.3.6.1.4.1.164.3.1.2.10.1.1.4
For MP-2100/MP-2200 and for MP-104/204 from R2: This object represents 6 parameters, by 3 Octets : Busy Code-MSB nibble, - applicable only for Rx translation Idle Code- nibble, - applicable only for Rx translation D Bit Code- nibble, C Bit Code- nibble, B Bit Code- nibble, A Bit Code-LSB nibble. Each of Busy and Idle Code nibble will have the valid values: 0000 .. FFFF. Each of A,B,C,D Bit Code nibble represents: 0 hex = 0000 = 0 1 hex = 0001 = 1 2 hex = 0010 = A bit 3 hex = 0011 = B bit 4 hex = 0100 = C bit 5 hex = 0101 = D bit 6 hex = 0110 = A bit inverse 7 hex = 0111 = B bit inverse 8 hex = 1000 = C bit inverse 9 hex = 1001 = D bit inverse A-F hex - not used (invalid values) For MP-104/204 R1: This object represents 3 parameters, by 2 Octets : Bit 1 = Bit A - OFF Hook for Tx ; Ring for Rx (LSB) Bit 2 = Bit B - OFF Hook for Tx ; Ring for Rx Bit 3 = Bit C - OFF Hook for Tx ; Ring for Rx Bit 4 = Bit D - OFF Hook for Tx ; Ring for Rx Bit 5 = Bit A - ON Hook for Tx ; Idle for Rx Bit 6 = Bit B - ON Hook for Tx ; Idle for Rx Bit 7 = Bit C - ON Hook for Tx ; Idle for Rx Bit 8 = Bit D - ON Hook for Tx ; Idle for Rx Bit 9 = Bit A - OOS State for both Tx and Rx Bit 10 = Bit B - OOS State for both Tx and Rx Bit 11 = Bit C - OOS State for both Tx and Rx Bit 12 = Bit D - OOS State for both Tx and Rx Bit 13 = Spare (always 0) Bit 14 = Spare (always 0) Bit 15 = Spare (always 0) Bit 16 = Spare (always 0) (MSB) When the object is not applicable, the Octet String will have 0 bytes.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

agnSigProfTable		1.3.6.1.4.1.164.3.1.2.10.2
The write operation into the Table Objects is valid only to the TmpCnfg entry. This is the general table of signaling profiles.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AgnSigProfEntry

agnSigProfEntry		1.3.6.1.4.1.164.3.1.2.10.2.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AgnSigProfEntry

agnSigProfCnfgIdx		1.3.6.1.4.1.164.3.1.2.10.2.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. The write operation is valid only to the TmpCnfg.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

agnSigProfIdx		1.3.6.1.4.1.164.3.1.2.10.2.1.2
This attribute indicates the Signaling Profile (1..5).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..5

agnSigProfName		1.3.6.1.4.1.164.3.1.2.10.2.1.3
Profile Name given by user.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..12)

agnSigProfType		1.3.6.1.4.1.164.3.1.2.10.2.1.4
Profile Type. legacy - usual signaling. The parameters for the Legacy Profiles are detailed in the agnSigProfileTable, above. r2Cas - R2 signaling. The parameters for the R2 Profiles are detailed in the r2 ProfileCnfg tables (belong to r2If).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), legacy(2), r2Cas(3)

systemVoiceTable		1.3.6.1.4.1.164.3.1.2.12.1
General Parameters for voice - system level.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SystemVoiceEntry

systemVoiceEntry		1.3.6.1.4.1.164.3.1.2.12.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SystemVoiceEntry

systemVoiceConfIdx		1.3.6.1.4.1.164.3.1.2.12.1.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed - Active or Temporary Configurations. Idx 255 relates to the temporary TmpCnfg. All configurations can be read but only the Temporary can be written to.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

systemVoiceNationalTone		1.3.6.1.4.1.164.3.1.2.12.1.1.2
Tone Characteristics (Amplitude, Frequency, delays etc.). These characteristics are defined according to the country.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), usa(2), australia(3), brazil(4), canada(5), france(6), germany(7), israel(8), mexico(9), portugal(10), russia(11), spain(12), unitedKingdom(13), czech(14), china(15)

systemVoicePacketRate		1.3.6.1.4.1.164.3.1.2.12.1.1.3
This object indicates the G.729 and G.711 Coders transmitted Packet Rate in milliseconds.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

systemVoiceFaxSupport		1.3.6.1.4.1.164.3.1.2.12.1.1.4
This object allows the user to Disable/Enable Fax support.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), faxRelayT38(3), vbdPassThrou(4)

systemVoiceFaxRate		1.3.6.1.4.1.164.3.1.2.12.1.1.5
This object indicates the Fax Rate limit. It is irrelevant when Fax support is NA or disabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notConnected(1), r4800bps(2), r9600bps(4), r14400bps(6)

systemVoiceModemSupport		1.3.6.1.4.1.164.3.1.2.12.1.1.6
This object allows the user to Disable/Enable Modem support.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), vbdV152(3), vbdPassThrou(4)

systemVoiceCoderAndRate		1.3.6.1.4.1.164.3.1.2.12.1.1.7
This object indicates the Coder and Rate for the Voice Compression.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), g711aLAW(5), g711uLAW(6)

systemVoiceEchoCanceler		1.3.6.1.4.1.164.3.1.2.12.1.1.8
This object indicates the Echo Canceler activation.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), enable(3)

systemVoiceTxGain		1.3.6.1.4.1.164.3.1.2.12.1.1.9
This object indicates the Transmit Gain (volume) in dB.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

systemVoiceDtmfRelayMethod		1.3.6.1.4.1.164.3.1.2.12.1.1.10
This object indicates the DTMF Relay Method that is used to transmit DTMF tones. rfc2833(1) - inband DTMF relay according to RFC-2833. sipInfo(2) - out of band DTMF relay using SIP INFO method.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	rfc2833(1), sipInfo(2)

systemVoiceDtmfRelayRxPayloadType		1.3.6.1.4.1.164.3.1.2.12.1.1.11
This object indicates the Rx Payload Type for DTMF relay RTP packets. It is relevant only when DTMF Relay Method is RFC-2833.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

systemVoiceDtmfRelayPayloadTypeNeg		1.3.6.1.4.1.164.3.1.2.12.1.1.12
This object indicates whether Payload Type Negotiation is used (according to RFC-2833) or not. It is relevant only when DTMF Relay Method is RFC-2833.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), enable(3)

systemVoiceDtmfRelayTxPayloadType		1.3.6.1.4.1.164.3.1.2.12.1.1.13
This object indicates the Tx Payload Type for DTMF relay RTP packets. It is relevant only when the Payload Type Negotiation is disabled.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

systemVoiceCoderTable		1.3.6.1.4.1.164.3.1.2.12.2
Voice Coders table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SystemVoiceCoderEntry

systemVoiceCoderEntry		1.3.6.1.4.1.164.3.1.2.12.2.1
An entry in Voice Coders table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SystemVoiceCoderEntry

systemVoiceCoderConfIdx		1.3.6.1.4.1.164.3.1.2.12.2.1.1
The first index of the table. This object might represent the Configuration Index (1..100) being accessed; Index=255 relates to the TmpCnfg. For devices with multiple configurations, Set is permitted to TmpCnfg(255) only. Not-Applicable = 1.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

systemVoiceCoderPriority		1.3.6.1.4.1.164.3.1.2.12.2.1.2
This object indicates the Coder's Priority.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

systemVoiceCoderCoderAndRate		1.3.6.1.4.1.164.3.1.2.12.2.1.3
This object indicates the Coder and Rate for the Voice Compression.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), g7231r6300BPS(2), g7231r5300BPS(3), g729A8KBPS(4), g711aLAW(5), g711uLAW(6), none(255)

mdlSInstTable		1.3.6.1.4.1.164.3.1.3.1.1
A table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MdlSInstEntry

mdlSInstEntry		1.3.6.1.4.1.164.3.1.3.1.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	MdlSInstEntry

mdlSInstSltIdx		1.3.6.1.4.1.164.3.1.3.1.1.1.1
A unique number to identify a slot position in the mux. In the ?004 Unit the entries PsB(2),ClB(4),io6(10)..io(16) are not valid. For the Vmux2100 Main Board clA (3) is used.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	psA(1), psB(2), clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

mdlSInstCardType		1.3.6.1.4.1.164.3.1.3.1.1.1.2
This attribute indicates the type of card installed in the specific slot position. Only PS cards are possible in the PS slots. Only CL cards are possible in the CL slots. Only IO cards are possible in the IO slots.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), empty(2), acm(9), ps60W(10), ps100W(11), ps(17), cl1(20), clEth(21), cl2(22), cl2Eth(23), cl3(24), cl3Eth(25), cl1Clk(26), mPh1(31), mPh3(32), mPh1T1DSU(33), mPh1T1CSU(34), mPh1E1DSU(35), mPh1E1LTU(36), mtmlFT1(37), mtmlFE1(38), mtmlH4E1(39), mtmlH4E12W(40), mtmlH4T1(41), mtmlH4T12W(42), mtHsh4E1(43), mtHsh4E12W(44), mtHsh4T1(45), mtHsh4T12W(46), mtmlH2E1(47), mtmlH2E12W(48), mtmlH2T1(49), mtmlH2T12W(50), hsh2E1(51), hsh2E12W(52), hsh2T1(53), hsh2T12W(54), mlIp(55), mtml4Ip(56), ml20N1(57), ml20N2(58), mPl6(60), mPl3(61), vf24T1(62), vf30E1(63), vf48T1(64), vf60E1(65), ml2E1(68), ml4E1(69), ml2T1(70), ml4T1(71), mPv4(72), vc16A(73), vc8EandM(74), vc8Fxo(75), vc8Fxs(76), vc16EandM(77), vc16Fxo(78), vc16Fxs(79), vf3EandM(80), vf3Fxs(81), vf3Fxo(82), vfPbx(83), vfPbxT1(84), vfPbxE1(85), mtMlE2S(86), mtMlE2D(87), mtMlF2T1(88), mtMlF2E1(89), mtMlT1Fiber(90), mtMlE1Fiber(91), mtMlT1FiberFb(92), mtMlE1FiberFb(93), mtmlHE1(94), mtmlH1E1(95), mtmlHSE1(96), ml20(97), mtMl4T1(98), mtMl4E1(99), mtMl1T1DSU(100), mtMl1T1CSU(101), mtMl1E1DSU(102), mtMl1E1LTU(103), mtMl1T1DSUfb(104), mtMl1T1CSUfb(105), mtMl1E1DSUfb(106), mtMl1E1LTUfb(107), mtMl2T1(108), mtMl2E1(109), ls2CcittX50(110), ls2CcittX58(111), ls2ATandTSdm(112), ls2ACcittX50(113), ls2ACcittX58(114), ls2AATandTSdm(115), ls2A2Ts(116), ls2M(117), mtMlT1(118), mtMlE1(119), hs2(120), hs3(121), hsq(122), hs703(123), hsQM(124), hsqN(125), hs6(126), hs12(127), hsDp(128), hsp(129), hs4T1(130), hs4E1(131), hs4(132), hsEth(133), ml8T1(134), ml8E1(135), vc2E1(136), vc4E1(137), vc2T1(138), vc4T1(139), vc2EandM(140), vc2Fxs1Plar(141), vc2Fxo1(142), vc2Fxs2(143), vc2Fxo2(144), vc2Fxs3(145), vc2Fxo3(146), vc26EandM(147), mtvc2(148), vc2R2Fxs(149), hsu(150), mbeA(151), mbeB(152), mbeU(153), tre(154), hsuI(155), hsr(156), hss(157), hsu1(158), ls12(159), ls6(160), ls6V1EandM(161), ls6V1Fxo(162), ls6V1Fxs(163), ls6V2EandM(164), ls6V2Fxo(165), ls6V2Fxs(166), ls6VfEandM(167), ls6VfFxo(168), ls6VfFxs(169), vc3EandM(170), vc3Fxo(171), vc3Fxs(172), vcPbx(173), vcPbxT1(174), vcPbxE1(175), vc6EandM(176), vc6Fxo(177), vc6Fxs(178), vcq(179), ls6n(180), mhs1V36(181), mhs1V35(182), mhs1G703(183), mhs1DDS(184), mhs3(185), mhs1X21(186), mhs1V24(187), mhs4(188), mhsE1Hs(189), mhsT1Hs(190), mhsHyE1Hs(191), mhsHyT1Hs(192), mlfHybE1Hs(193), mlfHybT1Hs(194), mhs2e1(195), mhs2t1(196), mhsHy2e1(197), mhsHy2t1(198), mlfHybE12(199), mls6(200), mls3(201), mlHybAtmE1(202), mlHybAtmT1(203), mlfHybT12(204), mvc8(205), mvc8PbxE1(206), mvc8PbxT1Dsu(207), mvc8PbxT1Csu(208), mvc8PbxE1Slave(209), mvc4(210), mvc4PbxE1(211), mvc4PbxT1Dsu(212), mvc4PbxT1Csu(213), mvc4PbxE1Slave(214), mvc4PbxT1Slave(215), mvc8PbxT1Slave(216), mvc8ExtAnalog(217), mvcE1(218), mvcT1(219), mhsS(220), mhsU(221), mhsPriE1(222), mhsPriT1(223), hsEthSwitch(224), mPriE1FramerCcs(225), mPriT1FramerCcs(226), mPriE1SlaveCcs(227), mPriT1SlaveCcs(228), mDualBri(229), vc12EandM(230), vc12Fxo(231), vc12Fxs(232), vc6aEandM(233), vc6aFxo(234), vc6aFxs(235), vc6AgFxo(236), vc6AgFxs(237), vc6a4LB(238), vid(239), hsu12(240), hsu6(241), hss12(242), hss6(243), hsDp3(244), hsDp6(245), hsf1(246), mhsHyE1(247), mhsHyT1(248), mhsIp(249), mlIpHs(250), mlHybIpE1(251), mlHybIpT1(252), mvg1Lan(253), mvg2Lan(254), vc4Fxs(255), vc4EandM(256), vc4Fxo(257), hsf2(258), mvgSwitch4Lan(260), msl4E1W2(261), msl4E1W4(262), msl8E1W2(263), msl4E1W2Eth(264), msl8E1W2Eth(265), asmi54cE1AndEth(266), asmi54cT1AndEth(267), hs6N(271), hs12N(272), hsNRZ(273), evc2E1(281), evc4E1(282), evc2T1(283), evc4T1(284), vc2E1Pri(285), vc4E1Pri(286), vc4OmniEandM(291), vc4OmniWestern(292), clx1(301), clx1GbE(302), clx1S155(303), clx1S155GbE(304), ml8T1Eth(305), ml8E1Eth(306), op106cEth(307), op108cEth(308), op106cEthT1(309), op108cEthE1(310), op108cEthE1Unbal(311), mpw1(312), vfs24T1(321), vfs30E1(322), vfs48T1(323), vfs60E1(324), mm4E1(325), mm4T1(326), mm8E1(327), mm8T1(328), mm12E1(329), mm12T1(330), mm16E1(331), mm16T1(332)

mdlSHwVersion		1.3.6.1.4.1.164.3.1.3.1.1.1.3
This attribute indicates the Hardware version of the installed card in the specific slot position.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

mdlSSwVersion		1.3.6.1.4.1.164.3.1.3.1.1.1.4
This attribute indicates the Software version of the installed card in the specific slot position.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

mdlSAlrStatus		1.3.6.1.4.1.164.3.1.3.1.1.1.5
Indicates the alarm state at module level, i.e. lower level (port alarms) status is not included. This attribute will be set to: critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), event(3), minor(4), major(5), warning(6), critical(7)

mdlSAlrStatusAll		1.3.6.1.4.1.164.3.1.3.1.1.1.6
Indicates the alarm state in the module-all level, i.e. lower level (port alarms) included. This attribute will be set to: critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), event(3), minor(4), major(5), warning(6), critical(7)

mdlSMaskedAlrStat		1.3.6.1.4.1.164.3.1.3.1.1.1.7
Indicates the alarm state at module level, [i.e. lower level (port alarms) status is not included],including Masked alarms. This attribute will be set to: critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), event(3), minor(4), major(5), warning(6), critical(7)

mdlSMaskedAlrStatAll		1.3.6.1.4.1.164.3.1.3.1.1.1.8
Indicates the alarm state in the module-all level, i.e. lower level (port alarms) included, including Masked alarms. This attribute will be set to: critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), event(3), minor(4), major(5), warning(6), critical(7)

mdlSTstStatusAll		1.3.6.1.4.1.164.3.1.3.1.1.1.9
This attribute will be set to on(3) when there is at least one test in progress on a channel of the card, otherwise the value will be off(2).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), on(3)

mdlSClearAlrCmd		1.3.6.1.4.1.164.3.1.3.1.1.1.10
Setting this command to ON, enforces a clear of all the alarms in the given slot, excluding alarms of port level. The clear operation will not be applied for masked/inverted alarms.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

mdlSClearAllAlrCmd		1.3.6.1.4.1.164.3.1.3.1.1.1.11
Setting this command to ON, enforces a clear of all the alarms in the given slot, including all its ports alarms. The clear operation will not be applied for masked/inverted alarms.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

mdlSTemperature		1.3.6.1.4.1.164.3.1.3.1.1.1.12
Temperature of the card, in Celsius degrees.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

mdlSAlrTable		1.3.6.1.4.1.164.3.1.3.1.2
The list of card agent alarms ; includes also an alarm indicating existence of alarms on its ports if there are any.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MdlSAlrEntry

mdlSAlrEntry		1.3.6.1.4.1.164.3.1.3.1.2.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	MdlSAlrEntry

mdlSAlrIdx		1.3.6.1.4.1.164.3.1.3.1.2.1.1
A unique number to identify an entry in the alarm status table. Users should use the get next function to read this table because the indexes are not consecutive.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

mdlSAlrSltIdx		1.3.6.1.4.1.164.3.1.3.1.2.1.2
This attribute indicates the desired slot position. In the ?004 Unit the entries PsB(2),ClB(4),io6(10)..io12(16) are not valid. For the Vmux2100 Main Board clA (3) is used.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	psA(1), psB(2), clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

mdlSAlrCodeDescription		1.3.6.1.4.1.164.3.1.3.1.2.1.3
This attribute is a full text description of the alarm . The alarm description includes the following information: alarm code, alarm text, alarm severity, Masked or Inverted flag and counter.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

mdlSAlrCode		1.3.6.1.4.1.164.3.1.3.1.2.1.4
A code identifying the alarm of an entry in the alarm status table at card level.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

mdlSAlrSeverity		1.3.6.1.4.1.164.3.1.3.1.2.1.5
The severity of the alarm.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	event(3), minor(4), major(5), warning(6), critical(7)

mdlSAlrState		1.3.6.1.4.1.164.3.1.3.1.2.1.6
State of the alarm.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), on(3)

mdlSAlrCounter		1.3.6.1.4.1.164.3.1.3.1.2.1.7
A counter - how many times the alarm occured since last clear operation. ON and OFF Alarm will be counted separately.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

mdlSAlrMask		1.3.6.1.4.1.164.3.1.3.1.2.1.8
Alarm mask : on/off.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), on(3)

mdlSAlrInvert		1.3.6.1.4.1.164.3.1.3.1.2.1.9
Alarm invert : on/off.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), on(3)

mdlCPrgTable		1.3.6.1.4.1.164.3.1.3.2.1
A table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MdlCPrgEntry

mdlCPrgEntry		1.3.6.1.4.1.164.3.1.3.2.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	MdlCPrgEntry

mdlCCnfgIdx		1.3.6.1.4.1.164.3.1.3.2.1.1.1
This attribute indicates the Idx of the Cnfg(1..100) being referred. Value 255 specifies the TmpCnfg
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

mdlCSltIdx		1.3.6.1.4.1.164.3.1.3.2.1.1.2
This attribute indicates a unique number of the slot position where the card is inserted. In the ?004 Unit the entries psB(2),clB(4),io6(10)..io(16) are not valid.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	psA(1), psB(2), clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

mdlCPrgCardType		1.3.6.1.4.1.164.3.1.3.2.1.1.3
This attribute indicates the type of card assigned to the specific slot in the common configuration. This object is identical in all the configurations (1..100). Only the TmpCnf(255) may have different value. The write operation is valid only to the TmpCnfg entry.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unknown(1), empty(2), acm(9), ps48x60W(10), ps48x100W(11), ps110x60W(12), ps110x100W(13), ps220x60W(14), ps220x100W(15), ps180W(16), ps(17), cl1(20), clEth(21), cl2(22), cl2Eth(23), cl3(24), cl3Eth(25), cl1Clk(26), mPh1(31), mPh3(32), mPh1T1DSU(33), mPh1T1CSU(34), mPh1E1DSU(35), mPh1E1LTU(36), mtmlFT1(37), mtmlFE1(38), mtmlH4E1(39), mtmlH4E12W(40), mtmlH4T1(41), mtmlH4T12W(42), mtHsh4E1(43), mtHsh4E12W(44), mtHsh4T1(45), mtHsh4T12W(46), mtmlH2E1(47), mtmlH2E12W(48), mtmlH2T1(49), mtmlH2T12W(50), hsh2E1(51), hsh2E12W(52), hsh2T1(53), hsh2T12W(54), mlIp(55), mtml4Ip(56), ml20N1(57), ml20N2(58), mPl6(60), vf24T1(62), vf30E1(63), vf48T1(64), vf60E1(65), ml2E1(68), ml4E1(69), ml2T1(70), ml4T1(71), vc16A(73), vc8EandM(74), vc8Fxo(75), vc8Fxs(76), vc16EandM(77), vc16Fxo(78), vc16Fxs(79), vf3EandM(80), vf3Fxs(81), vf3Fxo(82), vfPbx(83), vfPbxT1(84), vfPbxE1(85), mtMlE2S(86), mtMlE2D(87), mtMlF2T1(88), mtMlF2E1(89), mtMlT1Fiber(90), mtMlE1Fiber(91), mtMlT1FiberFb(92), mtMlE1FiberFb(93), mtmlHE1(94), mtmlH1E1(95), mtmlHSE1(96), ml20(97), mtMl4T1(98), mtMl4E1(99), mtMl1T1DSU(100), mtMl1T1CSU(101), mtMl1E1DSU(102), mtMl1E1LTU(103), mtMl1T1DSUfb(104), mtMl1T1CSUfb(105), mtMl1E1DSUfb(106), mtMl1E1LTUfb(107), mtMl2T1(108), mtMl2E1(109), ls2CcittX50(110), ls2CcittX58(111), ls2ATandTSdm(112), ls2ACcittX50(113), ls2ACcittX58(114), ls2AATandTSdm(115), ls2A2Ts(116), ls2M(117), mtMlT1(118), mtMlE1(119), hs2(120), hs3(121), hsq(122), hs703(123), hsQM(124), hsqN(125), hs6(126), hs12(127), hsDp(128), hsp(129), hs4T1(130), hs4E1(131), hsEth(133), ml8T1(134), ml8E1(135), vc2E1(136), vc4E1(137), vc2T1(138), vc4T1(139), vc2EandM(140), vc2Fxs1Plar(141), vc2Fxo1(142), vc2Fxs2(143), vc2Fxo2(144), vc2Fxs3(145), vc2Fxo3(146), vc26EandM(147), mtvc2(148), vc2R2Fxs(149), hsu(150), mbeA(151), mbeB(152), mbeU(153), tre(154), hsuI(155), hsr(156), hss(157), hsu1(158), ls12(159), ls6(160), ls6V1EandM(161), ls6V1Fxo(162), ls6V1Fxs(163), ls6V2EandM(164), ls6V2Fxo(165), ls6V2Fxs(166), ls6VfEandM(167), ls6VfFxo(168), ls6VfFxs(169), vc3EandM(170), vc3Fxo(171), vc3Fxs(172), vcPbx(173), vcPbxT1(174), vcPbxE1(175), vc6EandM(176), vc6Fxo(177), vc6Fxs(178), vcq(179), ls6n(180), mhs1V36(181), mhs1V35(182), mhs1G703(183), mhs1DDS(184), mhs3(185), mhs1X21(186), mhs1V24(187), mhs4(188), mhsE1Hs(189), mhsT1Hs(190), mhsHyE1Hs(191), mhsHyT1Hs(192), mlfHybE1Hs(193), mlfHybT1Hs(194), mhs2e1(195), mhs2t1(196), mhsHy2e1(197), mhsHy2t1(198), mlfHybE12(199), mls6(200), mls3(201), mlHybAtmE1(202), mlHybAtmT1(203), mlfHybT12(204), mvc8(205), mvc8PbxE1(206), mvc8PbxT1Dsu(207), mvc8PbxT1Csu(208), mvc8PbxE1Slave(209), mvc4(210), mvc4PbxE1(211), mvc4PbxT1Dsu(212), mvc4PbxT1Csu(213), mvc4PbxE1Slave(214), mvc4PbxT1Slave(215), mvc8PbxT1Slave(216), mvc8ExtAnalog(217), mvcE1(218), mvcT1(219), mhsS(220), mhsU(221), mhsPriE1(222), mhsPriT1(223), hsEthSwitch(224), mPriE1FramerCcs(225), mPriT1FramerCcs(226), mpriE1SlaveCcs(227), mpriT1SlaveCcs(228), mDualBri(229), vc12EandM(230), vc12Fxo(231), vc12Fxs(232), vc6aEandM(233), vc6aFxo(234), vc6aFxs(235), vc6AgFxo(236), vc6AgFxs(237), vc6a4LB(238), vid(239), hsu12(240), hsu6(241), hss12(242), hss6(243), hsDp3(244), hsDp6(245), hsf1(246), mhsHyE1(247), mhsHyT1(248), mhsIp(249), mlIpHs(250), mlHybIpE1(251), mlHybIpT1(252), mvg1Lan(253), mvg2Lan(254), vc4Fxs(255), vc4EandM(256), vc4Fxo(257), hsf2(258), mvgSwitch4Lan(260), msl4E1W2(261), msl4E1W4(262), msl8E1W2(263), msl4E1W2Eth(264), msl8E1W2Eth(265), asmi54cE1AndEth(266), asmi54cT1AndEth(267), hs6N(271), hs12N(272), hsNRZ(273), evc2E1(281), evc4E1(282), evc2T1(283), evc4T1(284), vc2E1Pri(285), vc4E1Pri(286), vc4OmniEandM(291), vc4OmniWestern(292), clx1(301), clx1GbE(302), clx1S155(303), clx1S155GbE(304), ml8T1Eth(305), ml8E1Eth(306), op106cEth(307), op108cEth(308), op106cEthT1(309), op108cEthE1(310), op108cEthE1Unbal(311), mpw1(312), vfs24T1(321), vfs30E1(322), vfs48T1(323), vfs60E1(324)

mdlCNoOfExternPrt		1.3.6.1.4.1.164.3.1.3.2.1.1.4
Number of external ports in the programmed card of the specific slot position
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

mdlCNoOfInternPrt		1.3.6.1.4.1.164.3.1.3.2.1.1.5
Number of internal ports in the programmed card of the specific slot position.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

mdlCWorkMode		1.3.6.1.4.1.164.3.1.3.2.1.1.6
Working mode of the card. The user may configure the card to work in a stand alone mode or integrated with the device. Example for use in MHS-IP cards: - standAlone - in this mode, the router works so that data is received via the LAN (Eth) port and is transmitted via the WAN (HS) external port without going through the MPH device. - integrated - in this mode, the router works so that it is integrated in the MPH and routes DLCIs into the device.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), standAlone(2), integrated(3)

mdlCDhcpClientEnable		1.3.6.1.4.1.164.3.1.3.2.1.1.7
Enable/Disable the feature of DHCP Client for the selected card.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), enable(3)

mdlCRdnExists		1.3.6.1.4.1.164.3.1.3.2.1.1.8
This object indicates whether any port of the programmed card is configured to be part of a Redundancy/APS pair. If at least one port of the programmed card is configured to be part of a Redundancy/APS pair, the value will be 'yes'. Otherwise, it will be 'no'.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	no(2), yes(3)

mdlCInterfaces		1.3.6.1.4.1.164.3.1.3.2.1.1.9
Octet string which indicates 'present' interfaces in card. Each '0' bit stands for non-present interface. Each '1' bit stands for present interface. For ASMi54C card of LRS-102 and MP-4100 notPresent interfaces may be: - SHDSL Line ID with no wire pairs assigned to it (does not exist in ifTable) - PCS without SHDSL Line binded to it, (exist in ifTable, with ifOperStatus= notPresent) - External DS1 when its LIU is used by an Internal DS1 of the same card - Internal DS1 when single bearer is not TDM. In each octet, MS bit represents port 1 and LS bit represents port 8 MSB LSB 1 0 0 0 1 0 0 0 -- Example: Port # 1 and 5 are present. Port 1 2 3 4 5 6 7 8 1st Octet (MSB octet) represents SDHSL Lines 2nd Octet represents PCS 3rd Octet represents External DS1 4th Octet represents Internal DS1 5th and 6th Octets are reserved for future Internal DS1. For OP-108/106 cards of LRS-102 and MP-4100 notPresent interfaces may be: - External DS1 when its 'associated' Int-DS1 port is connected to another card - Internal DS1 when its 'associated' Ext-DS1 port is connected to another card (Both may be 'present' when inter-connected). 1st Octet represents External DS1 2nd Octet represents Internal DS1 Bit representation, same as for ASMi-54C card.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

mdlCmprTable		1.3.6.1.4.1.164.3.1.3.3.1
A table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MdlCmprEntry

mdlCmprEntry		1.3.6.1.4.1.164.3.1.3.3.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	MdlCmprEntry

mdlCmprTypIdx		1.3.6.1.4.1.164.3.1.3.3.1.1.1
This attribute indicates the Type of the Compressed being referred.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

mdlCmprCnfgIdx		1.3.6.1.4.1.164.3.1.3.3.1.1.2
This attribute indicates the configuration to which the Compressed information is related.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

mdlCmprVersion		1.3.6.1.4.1.164.3.1.3.3.1.1.3
This attribute indicates the version of the internal format of the Compressed data
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

mdlCmprSltIdx		1.3.6.1.4.1.164.3.1.3.3.1.1.4
This attribute indicates a unique number of the slot position where the card is inserted. In the ?004 Unit the entries psB(2),clB(4),io6(10)..io(16) are not valid.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	psA(1), psB(2), clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

mdlCmprObj		1.3.6.1.4.1.164.3.1.3.3.1.1.5
This attribute is the compressed information itself.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

mdlAlarmsCmprTable		1.3.6.1.4.1.164.3.1.3.3.2
A table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MdlAlarmsCmprEntry

mdlAlarmsCmprEntry		1.3.6.1.4.1.164.3.1.3.3.2.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	MdlAlarmsCmprEntry

mdlAlarmsCmprVersion		1.3.6.1.4.1.164.3.1.3.3.2.1.1
This attribute indicates the version of the internal format of the Compressed data
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

mdlAlarmsCmprAlarmSlot		1.3.6.1.4.1.164.3.1.3.3.2.1.2
This attribute indicates the desired slot position. In the ?004 Unit the entries PsB(2),ClB(4),io6(10)..io(16) are not valid.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

mdlAlarmsCmprAlarmIdx		1.3.6.1.4.1.164.3.1.3.3.2.1.3
A unique number to identify an entry in the alarm status table of the agent.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

mdlAlarmsCmprObj		1.3.6.1.4.1.164.3.1.3.3.2.1.4
This attribute is the compressed information itself.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

prtSInstTable		1.3.6.1.4.1.164.3.1.4.1.1
A table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtSInstEntry

prtSInstEntry		1.3.6.1.4.1.164.3.1.4.1.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtSInstEntry

prtSInstSltIdx		1.3.6.1.4.1.164.3.1.4.1.1.1.1
This attribute indicates a unique number to identify the slot where the card is inserted. In the ?004 Unit the entries io6(10)..io(16) are not valid. For the Vmux2100 Main Board clA (3) is used.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

prtSInstPrtIdx		1.3.6.1.4.1.164.3.1.4.1.1.1.2
This attribute indicates a unique number to identify a port in a specific card. The valid ports depend on the installed card: the valid external ports (interfaces) are (1..mdlCNoOfExternPrt) if any, and the valid internal ports are (101..100+mdlCNoOfInternPrt) if any. Generally, for MP-2100/2200: exPrt1 (1) .. exPrt16 (16),inPrt1(101) .. inPrt48 (148) For the Vmux-2100 device: This index will have values of 1...4 for the physical ports & values of ifIndex for the bundles. For other products, see product's spec.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtSInstPrtType		1.3.6.1.4.1.164.3.1.4.1.1.1.3
This attribute describes the type of the designated port. In MX 3000 only external & internal options are used. All the other options are only for MX 30/300 which need special handling. In order to support interface types in MX 3000, return an ascii string for prtSInterfaceType in this table or support the general RAD value of physicalConnector. External port - is a port with a physical connector. Internal port - might be of two types: a) A composite port which collects a few external ports data into a common bandwidth (usually routed through DS1 link) b) A port which gets only part of the external ports (usually a few DS0's) The following types are used when all ports are external/ internal and the connector/interface type is necessary (for example, stand-alone units): High Speed port types Low Speed port types Voice port types, CL port types. ISDN Voice in MX 30/300 Phase 4: voiceS0 (16), voiceU (17) should be used. ISDN Voice in MX 30/300 Phase 5: voiceQsigS(18), voiceQsigU (19) should be used.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	external(2), internal(3), highSpeedV35(4), highSpeedV24(5), highSpeedV36(6), highSpeedX21(7), highSpeedG703(8), highSpeedDDS(9), lowSpeed(10), voice(11), cl(12), isdns(13), isdnu(14), ethernet(15), voiceS0(16), voiceU(17), voiceQsigS(18), voiceQsigU(19)

prtSInstIfIndex		1.3.6.1.4.1.164.3.1.4.1.1.1.4
This attribute indicates the unique interface number assigned to the port. The specific interface of this attribute is the same as the interface identified by the value of ifindex in MIB-II.If there is no interface for the specific prtIdx the value will be '7fffffff'h.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtSActiveStatus		1.3.6.1.4.1.164.3.1.4.1.1.1.5
This attribute describes the activity status of the port. unknown(1) indicates that the information is not supported. notUsed(2) indicates that the ch is not connected according to the active config. offLine(3) indicates that the ch is down (not working) because of any problem. onLine(4) indicates that the ch is up (working) offLineRedundancy(5) indicates that the ch is down, because it is redundant port. onLineRedundancy(6) indicates that the ch is up, and it is the active link
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), notUsed(2), offLine(3), onLine(4), offLineRedundancy(5), onLineRedundancy(6)

prtSAlrStatus		1.3.6.1.4.1.164.3.1.4.1.1.1.6
Indicates the alarm state in the port(ch) agent level. This attribute will be set to: critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), event(3), minor(4), major(5), warning(6), critical(7)

prtSMaskedAlrStat		1.3.6.1.4.1.164.3.1.4.1.1.1.7
Indicates the alarm state in the port(ch) agent level, including Masked alarms. This attribute will be set to: critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), event(3), minor(4), major(5), warning(6), critical(7)

prtSClearAlrCmd		1.3.6.1.4.1.164.3.1.4.1.1.1.8
Setting this attribute to on(3) enforces a clear operation of the alarm status events in the given port. The clear operation will not be applied for masked/inverted alarms.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

prtSTestMask		1.3.6.1.4.1.164.3.1.4.1.1.1.9
This is a mask which indicates which tests from the 'prtSTstCmd' list are allowed for the requested port. If a specific test is allowed, its respective bit will be SET in the mask : TEST BIT ----------- --- local-loop 1 remote-loop 2 loc-and-rem-main-loops 3 remote-analog-loop 4 remote-digital-loop 5 rem-loop-on-ext-unit 6 bert 7 tone-injection 8 dlci local-loop 9 all dlci local-loop 10 dlci remote-loop 11 all dlci remote-loop 12 bert-and-rem-loop-on-rem-unit 13 rem-loop-on-rem-unit 14 block 15 backward-tone-inject 16 llb 17 rlb 18 ft1Enable 21 lbbd 22 --for 2B+D lb1 23 --for B1 lb2 24 --for B2 llb-on-rem-unit 25 bert-on-rem-unit 26 bert-on-rem-and-llb-on-rem-unit 27 local-and-bert-on-rem-unit 28 local-loop-on-rem-unit 29 localBert 30 --towards IO ports test-per-TS 31 e.g : If the return value is 3 -> 0000000000000011 -> Bits 1 & 2 are set -> the allowed tests are : local-loop remote-loop
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtSTstCmd		1.3.6.1.4.1.164.3.1.4.1.1.1.10
Setting this attribute to any of the above values will initiate a test on the specific port if the operation is legal. If the operation is not legal, the mux will ignore the operation. testPerTS(31) - when this test is selected, the selection of tests for each TS is done via the prtExPh1MlTsTest object. If a test time out is needed, the test will be set with a default timeout of 2 minutes until the user will set the parameter 'prtSTstDuration' to the required time out. If no time out is needed , the test will be set with infinite timeout until the user will set the parameter 'prtSTstDuration' to the required time out.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), localLoop(2), remoteLoop(3), locAndRemMainLoops(4), remoteAnalogLoop(5), remoteDigitalLoop(6), remLoopOnExtUnit(7), bert(8), toneInjection(9), dlciLocalLoop(10), allDlciLocalLoop(11), dlciRemoteLoop(12), allDlciRemoteLoop(13), extInitLocalLoop(14), bertAndRemLoopOnRemUnit(15), remLoopOnRemUnit(16), block(17), backwardToneInject(18), llb(19), rlb(20), ft1Enable(21), lbbd(22), lb1(23), lb2(24), llbOnRemUnit(25), bertOnRemUnit(26), bertOnRemAndLlbOnRemUnit(27), localAndBertOnRemUnit(28), localLoopOnRemUnit(29), localBert(30), testPerTS(31), csuLoopAndBert(32), dsuLoopAndBert(33), remoteOcuLoopAndBert(34), remoteCsuLoopAndBert(35), remoteDsuLoopAndBert(36)

prtSTstDuration		1.3.6.1.4.1.164.3.1.4.1.1.1.11
This attribute indicates the maximum duration of executing a test on the specific port. This entry applies to all the test operations. The resolution will be a minute, and the maximum duration is limited to 30 minutes. For Vmux devices, the values are in seconds. A zero value specifies no time limitation. When the test isn't active, the agent initiates this object to 2 when the duration is needed and to 0 if its not required. The user should set this parameter after setting the 'prtSTstCmd' parameter.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtSBertClrCmd		1.3.6.1.4.1.164.3.1.4.1.1.1.12
Setting this attribute initiates bert count clear operation. It is valid only when bert test is active on the specific port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

prtSBertTstRslt		1.3.6.1.4.1.164.3.1.4.1.1.1.13
This attribute indicates the number of Bit Error Rate indicated during the BERT operation. It is valid only when bert test is active on the specific port.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtSInterfaceType		1.3.6.1.4.1.164.3.1.4.1.1.1.14
This attribute indicates a unique HW interface type of the selected port.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

prtSParamStatus		1.3.6.1.4.1.164.3.1.4.1.1.1.15
This object indicates Status of parameters specific to the selected port. - For a port that has no special status or is supported by prtSExHsfStatTable - 1 Octet: 00hex - For VC-6, VC-6A, VC-6AG, VC-6A/4LB, VC-12, VC-12/6, external ports - 1 Octet : Bit 7 (MSB)..Bit 2 = 0 (NA) Bit 1: Tx Signaling '1'=On ; '0'=Off Bit 0 (LSB): Rx Signaling '1'=On ; '0'=Off - For VC-2/R2(FXS) external ports - 1 Octet : Bit - 7 6 5 4 3 2 1 0 |_| |_________| Call Call State Direction Bit 7 (MSB) and Bit 6 : Call Direction 00 - Incoming 01 - Outgoing Bit 5..Bit 0: Call State 000000 - Idle 000001 - Seized 000010 - Both-Way Conflict 000011 - Seizure Ack 000100 - Answered 000101 - Clear Backward 000110 - Clear Forward 000111 - Blocked 001000 - Fault 001001 - Fault 3 001010 - Fault 4 001011 - Fault 5 001100 - Fault 6 001101 - Fault 7 - For ML-20 external port - 3 Octets : - 1 MS Octet will represent the Real Rate used: Bit - 7 6 5 4 3 2 1 0 |___| |_______| spare Rate Valid values: 0..31, meaning 0..31x64Kbps Invalid values: 32..255. - 2 LS Octets will represent the Status of 7 Control Signals: Signal - --- CTS DSR DCD RJ TM DTR RTS Bit - 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 Octet - 2 3 (LS) '---' will always have the value 00 Rest of the Signals (2 bits each) can have the following values: 00=NA ; 01=unused ; 10=Off ; 11=On - For ML-H/E1, ML-H/1/E1, ML-H/S/E1 internal port - 1 Octet Bit - 7 6 5 4 3 2 1 0 |___________| spare Mode of Operation Mode of Operation: '1'=Central ; '0'=Remote - For ACM external port - 1 Octet Bit - 7 6 5 4 3 2 1 0 |_________| spare Alarm State Alarm State: according to bits 1,0: 00=NA ; 01=unused ; 10=Off ; 11=On - For HS-U/1 external port - 1 Octet Bit 7 6 5 4 3 2 1 0 LSB |________| |__| |__| spare modem sync modem: 00 = other sync: 00 = not sync 01 = unknown 01 = sync 10 = ASMi-31/2 10 = reserved 11 = reserved 11 = reserved - For MTML-2/4 external ports, ML-8 externalports, ML-IP (MTML-IP) internal ports and MTML-E2 internal ports - 1 Octet : Bit 7 6 5 4 3 2 1 0 LSB | BERT State BERT State (Bit 0): 0 = OFF (BERT is not running on this port or any of its TSs/Bits) 1 = ON (BERT is running on this port OR on one of its TSs/Bits) - For ML-20N external ports - 4 Octets - 1 MS Octet will represent the Actual Link Rate: Bit - 7 6 5 4 3 2 1 0 |_| |_________| spare Rate Valid values: 0..34, meaning: 0..32 = (0..32)x64Kbps 33 = Invalid Rate 34 = not applicable (when Rate is not Auto) 35 = 0 Kbps Invalid values: 36..255. - 2 middle Octets will represent the Status of 4 Control Signals: - LS Octet - Bits 3-0: RTS/C (Command, for X.21 interface) Bits 7-4: DCD/I (Indication for X.21 interface) - MS Octet - Bits 3-0: DTR Bits 7-4: DSR Each 4 Bits are divided as follows: - 2 MS bits: DCE - 2 LS bits: DTE For each 2 bits (DCE/DTE): 00=NA ; 01=unused ; 10=Off ; 11=On. - LS Octet: (as for MTML-2): Bit 7 6 5 4 3 2 1 0 LSB | BERT State BERT State (Bit 0): 0 = OFF (BERT is not running on this port or any of its TSs/Bits) 1 = ON (BERT is running on this port OR on one of its TSs/Bits) - For MP-2100/2200 MSL-4/E1, MSL-8/E1 External ports - 3 Octets - MS octet: far-end modem channel interface - Middle octet: Material (plastic/metal), far-end modem type, synchronization with far-end modem - LS octet: BERT state (at port/TS/Bit level) - MS octet: 0000 0000 = no interface 0000 0001 = db15 (X21) 0000 0010 = IR-IP 0000 0011 = IR-ETH-Q 0000 0100 = V35 0000 0101 = ETH-RJ45 0000 0110 = G703 0000 0111 = db25 (RS530) 0000 1000 = ETH-BNC 0000 1001 = E1(Balanced) 0000 1010 = E1(Unbalanced) 0000 1011 = IR-ETH-QN Rest of the combinations: reserved - Middle octet: Bit 7 6 5 4 3 2 1 0 LSB | |___________| |__| Box material modem sync Box material modem: 00000 = other sync: 00 = not sync (for ASMi-52 SA) 00001 = unknown 01 = sync 0=metal 00010 = reserved 10 = reserved 1=plastic 00011 = reserved 11 = reserved 00100 = reserved 00101 = reserved 00110 = ASMi-52 SA/2W/Slave 00111 = ASMi-52 SA/2W/Master 01000 = ASMi-52/CQ card of LRS-24 01001 = ASMi-52/CD card of LRS-24 01010 = D16GSDSL card of DXC-3000 01011 = LRS-52 01100 = FCD-IP 01101 = FCD-IPM 01110 = D8SL card of DXC-30 01111 = ASMi-52A 10000 = MP card (SHDSL) 10001 = ASMi-52L Rest = reserved - LS Octet: (as for MTML-2): Bit 7 6 5 4 3 2 1 0 LSB | BERT State BERT State (Bit 0): 0 = OFF (BERT is not running on this port or any of its TSs) 1 = ON (BERT is running on this port OR on one of its TSs) - For MP-4100 MSL card Links - 4 Octets - MS octet: far-end modem DTE2 interface (same as for MP-2100 MSL cards) - after MS octet: far-end modem DTE1 interface (same as for MP-2100 MSL cards) - before LS octet: Material (plastic/metal), far-end modem type, synchronization with far-end modem (same as for MP-2100 MSL cards) - LS octet: BERT state (at port/TS/Bit level)- same as for MP-2100 MSL cards - For MP-4100, LRS-102 OP-108/106 Links - 3 Octets - MS octet: far-end PS type and state - Middle octet: synchronization with far-end device - LS octet: BERT state (at port/TS level) - same as for MP-2100 MSL cards - MS octet: Bit 7 6 5 4 3 2 1 0 LSB |__| |__| |__| |__| PS-A PS-A PS-B PS-B PS Type PS State PS Type PS State 00=None 00=None 01=AC-DC 01=OK 10=DC 10=Fail - Middle octet: Bit 7 6 5 4 3 2 1 0 LSB |__| sync: 00 = not sync 01 = sync 10 = reserved 11 = reserved Rest = reserved
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

prtSTestMaskXp		1.3.6.1.4.1.164.3.1.4.1.1.1.16
This is an Expanded test mask of the prtSTestMask object. The prtSTestMask object reached its maximum, being an Integer with 32 bits. This object indicates which tests from the 'prtSTstCmdXP' list are allowed for the selected port. If a specific test is allowed, its respective bit will be SET in the mask : TEST BIT ----------- --- local-loop 1 remote-loop 2 loc-and-rem-main-loops 3 remote-analog-loop 4 remote-digital-loop 5 rem-loop-on-ext-unit 6 bert 7 tone-injection 8 dlci local-loop 9 all dlci local-loop 10 dlci remote-loop 11 all dlci remote-loop 12 bert-and-rem-loop-on-rem-unit 13 rem-loop-on-rem-unit 14 block 15 backward-tone-inject 16 llb 17 rlb 18 ft1Enable 21 lbbd 22 --for 2B+D lb1 23 --for B1 lb2 24 --for B2 llb-on-rem-unit 25 bert-on-rem-unit 26 bert-on-rem-and-llb-on-rem-unit 27 local-and-bert-on-rem-unit 28 local-loop-on-rem-unit 29 localBert 30 --towards IO ports test-per-TS 31 csuLoopAndBert 32 dsuLoopAndBert 33 remoteOcuLoopAndBert 34 remoteCsuLoopAndBert 35 remoteDsuLoopAndBert 36 e.g : If the return value is 00000003 hex -> Bits 1 & 2 are set -> the allowed tests are : local-loop remote-loop
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

prtSRdnStatus		1.3.6.1.4.1.164.3.1.4.1.1.1.17
Redundancy Status of this port. noRdn - this port is not part of a Redundancy pair/group. offline - this port is offline from Redundancy point of view. online - this port is online from Redundancy point of view.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	noRdn(1), offline(2), online(3)

prtSAlrTable		1.3.6.1.4.1.164.3.1.4.1.2
The list of port agent alarms.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtSAlrEntry

prtSAlrEntry		1.3.6.1.4.1.164.3.1.4.1.2.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtSAlrEntry

prtSAlrIdx		1.3.6.1.4.1.164.3.1.4.1.2.1.1
A unique number to identify an entry in the alarm status table. Users should use the get next function to read this table because the indexes are not consecutive
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtSAlrSltIdx		1.3.6.1.4.1.164.3.1.4.1.2.1.2
This attribute indicates a unique identifier of the slot where the card is inserted. In the ?004 Unit the entries PsB(2),ClB(4),io6(10)..io12(16) are not valid. For the Vmux2100 Main Board clA (3) is used.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	psA(1), psB(2), clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

prtSAlrPrtIdx		1.3.6.1.4.1.164.3.1.4.1.2.1.3
This attribute indicates a unique identifier of the port the alarm applies to. All the values are valid. No alarms exist for a port which does not exist. Valid valuesfor MP-2100/2200: exPrt1 (1) .. exPrt16 (16) , inPrt1 (101) .. inPrt48 (148), IP Bundles. For other products, see product's spec.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtSAlrCodeDescription		1.3.6.1.4.1.164.3.1.4.1.2.1.4
This attribute is a full text description of the alarm. The alarm description includes the following information: alarm code, alarm text, alarm severity, Masked or Inverted flag and counter.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

prtSAlrCode		1.3.6.1.4.1.164.3.1.4.1.2.1.5
A code identifying the alarm of an entry in the alarm status table at port level.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtSAlrSeverity		1.3.6.1.4.1.164.3.1.4.1.2.1.6
The severity of the alarm.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	event(3), minor(4), major(5), warning(6), critical(7)

prtSAlrState		1.3.6.1.4.1.164.3.1.4.1.2.1.7
State of the alarm.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), on(3)

prtSAlrCounter		1.3.6.1.4.1.164.3.1.4.1.2.1.8
A counter - how many times the alarm occured since last clear operation. ON and OFF Alarm will be counted separately.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtSAlrMask		1.3.6.1.4.1.164.3.1.4.1.2.1.9
Alarm mask : on/off.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), on(3)

prtSAlrInvert		1.3.6.1.4.1.164.3.1.4.1.2.1.10
Alarm invert : on/off.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), on(3)

prtSAlrCardType		1.3.6.1.4.1.164.3.1.4.1.2.1.11
This attribute indicates the type of card installed in the specific slot position. The enumeration is according to mdlSInstCardType.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), empty(2), ps(17), cl1(20), cl1Clk(26), vf24T1(62), vf30E1(63), vf48T1(64), vf60E1(65), vc8EandM(74), vc8Fxo(75), vc8Fxs(76), vc16EandM(77), vc16Fxo(78), vc16Fxs(79), ml8T1(134), ml8E1(135), hsr(156), ls12(159), ls6n(180), hsEthSwitch(224), hsu12(240), hsu6(241), vc4Fxs(255), vc4EandM(256), vc4Fxo(257), msl4E1W2(261), msl8E1W2(263), msl4E1W2Eth(264), msl8E1W2Eth(265), asmi54cE1AndEth(266), asmi54cT1AndEth(267), hs6N(271), hs12N(272), clx1(301), clx1GbE(302), clx1S155(303), clx1S155GbE(304), ml8T1Eth(305), ml8E1Eth(306), op106cEth(307), op108cEth(308), op106cEthT1(309), op108cEthE1(310), op108cEthE1Unbal(311), mpw1(312), vfs24T1(321), vfs30E1(322), vfs48T1(323), vfs60E1(324)

prtFrStatisTable		1.3.6.1.4.1.164.3.1.4.1.3.1.1
This table is applicable only for an active port running an FR protocol .
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtFrStatisEntry

prtFrStatisEntry		1.3.6.1.4.1.164.3.1.4.1.3.1.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtFrStatisEntry

prtFrStatisSltIdx		1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.1
This attribute indicates a unique slot position where the module is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid. For stand-alone units this index will be notApplicable (255).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

prtFrStatisPrtIdx		1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.2
This attribute indicates a unique port number.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), exPrt5(5), exPrt6(6)

prtFrStatisInvIdx		1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.3
The Interval of 15 min. for which the following statistics counters are applicable.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	currentInv(1), last(2)

prtFrTimeElapsed		1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.4
The number of seconds that have elapsed since the beginning of the current error-measurement interval. This object is applicable mainly for the current interval. For other interval: - if data is available: value will be 899. - if data is not available: value will be 0.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..899

prtFrRxTotalFrames		1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.5
The total number of frames received by this port during the selected interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prtFrTxTotalFrames		1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.6
The total number of frames sent by this port during the selected interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prtFrRxTotalBytes		1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.7
The total number of bytes received by this port during the selected interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prtFrTxTotalBytes		1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.8
The total number of bytes sent by this port during the selected interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prtFrRxMngFrames		1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.9
The management number of frames received by this port during the selected interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prtFrTxMngFrames		1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.10
The management number of frames sent by this port during the selected interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prtFrRxDeFrames		1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.11
The number of De frames received by this port during the selected interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prtFrTxDeFrames		1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.12
The number of De frames sent by this port during the selected interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prtFrRxDcrdCongDeFr		1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.13
The number of De frames discarded due to congestion, received by this port during the selected interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prtFrTxDcrdCongDeFr		1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.14
The number of De frames discarded due to congestion, sent by this port during the selected interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prtFrRxDcrdCongAllFr		1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.15
All the frames discarded due to congestion, received by this port during the selected interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prtFrTxDcrdCongAllFr		1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.16
All the frames discarded due to congestion, sent by this port during the selected interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prtFrRxFecn		1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.17
Number of frames received by this port during the selected interval, indicating forward congestion.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prtFrTxFecn		1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.18
Number of frames sent by this port during the selected interval, indicating forward congestion.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prtFrRxBecn		1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.19
Number of frames received by this port during the selected interval, indicating backward congestion.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prtFrTxBecn		1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.20
Number of frames sent by this port during the selected interval, indicating backward congestion.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prtFrRxBeViol		1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.21
Number of data frames received by this port during the selected interval, exceeding the Burst Excess value.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prtFrTxBeViol		1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.22
Number of data frames sent by this port during the selected interval, exceeding the Burst Excess value.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prtFrRxBcViol		1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.23
Number of data frames received by this port during the selected interval, exceeding the Burst Committed value.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prtFrTxBcViol		1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.24
Number of data frames sent by this port during the selected interval, exceeding the Burst Committed value.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prtCrStatisTable		1.3.6.1.4.1.164.3.1.4.1.3.2.1
This table is applicable only for an active port running a CR protocol .
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtCrStatisEntry

prtCrStatisEntry		1.3.6.1.4.1.164.3.1.4.1.3.2.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtCrStatisEntry

prtCrStatisSltIdx		1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.1
This attribute indicates a unique slot position where the module is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid. For stand-alone units this index will be notApplicable (255).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

prtCrStatisPrtIdx		1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.2
This attribute indicates a unique port number.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), exPrt5(5), exPrt6(6)

prtCrStatisInvIdx		1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.3
The Interval of 15 min. for which the following statistics counters are applicable.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	currentInv(1), last(2)

prtCrTimeElapsed		1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.4
The number of seconds that have elapsed since the beginning of the current error-measurement interval. This object is applicable mainly for the current interval. For other interval: - if data is available: value will be 899. - if data is not available: value will be 0.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..899

prtCrRxTotalCells		1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.5
The total number of cells received by this port during the selected interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prtCrTxTotalCells		1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.6
The total number of cells sent by this port during the selected interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prtCrRxDataCells		1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.7
The number of Data Cells received by this port during the selected interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prtCrTxDataCells		1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.8
The number of Data Cells sent by this port during the selected interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prtDlciStatisTable		1.3.6.1.4.1.164.3.1.4.1.3.3.1
This table is applicable only for an active port running an FR, FR+ or CR protocol, with valid DLCIs .
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtDlciStatisEntry

prtDlciStatisEntry		1.3.6.1.4.1.164.3.1.4.1.3.3.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtDlciStatisEntry

prtDlciSltIdx		1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.1
This attribute indicates a unique slot position where the module is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid. For stand-alone units this index will be notApplicable (255).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

prtDlciPrtIdx		1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.2
This attribute indicates a unique port number.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), exPrt5(5), exPrt6(6)

prtDlciIdx		1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.3
This attribute indicates a unique DLCI index for each valid DLCI (16..991).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..991

prtDlciRxDeFrames		1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.4
The number of De frames received by this DLCI.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prtDlciTxDeFrames		1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.5
The number of De frames sent by this DLCI.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prtDlciRxDcrdCongDeFr		1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.6
The number of De frames discarded due to congestion, received by this DLCI.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prtDlciTxDcrdCongDeFr		1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.7
The number of De frames discarded due to congestion, sent by this DLCI.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prtDlciRxDcrdCongAllFr		1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.8
All the frames discarded due to congestion, received by this DLCI.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prtDlciTxDcrdCongAllFr		1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.9
All the frames discarded due to congestion, sent by this DLCI.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prtDlciTxFecn		1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.10
Number of frames sent by this DLCI, indicating forward congestion.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prtDlciTxBecn		1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.11
Number of frames sent by this DLCI, indicating backward congestion.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prtDlciRxBeViol		1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.12
Number of data frames received by this DLCI, exceeding the Burst Excess value.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prtDlciTxBeViol		1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.13
Number of data frames sent by this DLCI, exceeding the Burst Excess value.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prtDlciRxBcViol		1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.14
Number of data frames received by this DLCI, exceeding the Burst Committed value.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prtDlciTxBcViol		1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.15
Number of data frames sent by this DLCI, exceeding the Burst Committed value.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prtT1FdlMsgTable		1.3.6.1.4.1.164.3.1.4.1.3.4.1
This table is applicable for a T1 interface with 'esf' LineType .
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtT1FdlMsgEntry

prtT1FdlMsgEntry		1.3.6.1.4.1.164.3.1.4.1.3.4.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtT1FdlMsgEntry

prtT1FdlMsgSltIdx		1.3.6.1.4.1.164.3.1.4.1.3.4.1.1.1
This attribute indicates a unique slot position where the module is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

prtT1FdlMsgPrtIdx		1.3.6.1.4.1.164.3.1.4.1.3.4.1.1.2
This attribute indicates a unique port number. MTML-1/T1 modules have just one external interface.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	exPrt1(1)

prtT1FdlMsgFdlTxRx		1.3.6.1.4.1.164.3.1.4.1.3.4.1.1.3
The Fdl tx/rx reference of the Fdl message.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	tx(1), rx(2)

prtT1FdlMsg		1.3.6.1.4.1.164.3.1.4.1.3.4.1.1.4
FDL message.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

prtExTsSplitTable		1.3.6.1.4.1.164.3.1.4.2.1
The write operation into the Table Objects is valid only to the TmpCnfg entry, except prtExTsBitTest that will be written directly to the Active Configuration.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtExTsSplitEntry

prtExTsSplitEntry		1.3.6.1.4.1.164.3.1.4.2.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtExTsSplitEntry

prtExTsCnfgIdx		1.3.6.1.4.1.164.3.1.4.2.1.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtExTsSltIdx		1.3.6.1.4.1.164.3.1.4.2.1.1.2
This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid. notApplicable - for stand-alone units.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

prtExTsPrtIdx		1.3.6.1.4.1.164.3.1.4.2.1.1.3
This attribute indicates a unique port number. Most ML cards have only one external interface. inPrt1 - for MTML-H/E1 cards. For other products' index see their specification.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtExTsIdx		1.3.6.1.4.1.164.3.1.4.2.1.1.4
This attribute indicates a unique time slot position. The valid time slots are: 1..24 for T1 Card and 1..31 for E1 interface. In G732S-E1 lines, time slot 16 is not valid for data, it is dedicated to multiframe synchronization bits and voice signaling.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtExTsBit		1.3.6.1.4.1.164.3.1.4.2.1.1.5
This attribute indicates a unique Bit within the time slot. The valid Bits are: 1..8. 255=NA.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtExTsIConSlot		1.3.6.1.4.1.164.3.1.4.2.1.1.6
This attribute indicates whether the specified time slot is connected/routed internally in the Agent and to which card it is connected. In the ?004 Unit the entries io6(10)..io12(16) are not valid. notApplicable - for stand-alone units.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noConnect(2), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

prtExTsIConPrt		1.3.6.1.4.1.164.3.1.4.2.1.1.7
This attribute indicates the internally (In Mux) connected/routed port. For other products' index see their specification.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtExTsBitTest		1.3.6.1.4.1.164.3.1.4.2.1.1.8
This attribute indicates a test to be activated on the selected Bit. It is applicable only when prtExPh1MlTsTest=split(254). none - no test is applied for the selected Bit. notApplicable - when prtExPh1MlTsTest is NOT split(254).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), remoteBert(8), localBert(30), notApplicable(255)

prtExTsTxSignaling		1.3.6.1.4.1.164.3.1.4.2.1.1.9
Link - Tx Signaling per TS, for TSs having TS Type=Voice (agnTsType=voice(2)). It monitors what is sent to Link for the selected TS, for A,B,C,D Signaling Bits. Bit 1= LSB Bit 8= MSB Bit 1-2 = A Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 3-4 = B Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 5-6 = C Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 7-8 = D Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

prtExTsRxSignaling		1.3.6.1.4.1.164.3.1.4.2.1.1.10
Link - Rx Signaling per TS, for TSs having TS Type=Voice (agnTsType=voice(2)). It monitors what is received from Link for the selected TS, for A,B,C,D Signaling Bits. Bit 1= LSB Bit 8= MSB Bit 1-2 = A Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 3-4 = B Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 5-6 = C Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 7-8 = D Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

prtExTsTxIoSignaling		1.3.6.1.4.1.164.3.1.4.2.1.1.11
IO - Tx Signaling per TS, for TSs having TS Type=Voice (agnTsType=voice(2)). It monitors what is sent to IO port for the selected TS, for A,B,C,D Signaling Bits. Bit 1= LSB Bit 8= MSB Bit 1-2 = A Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 3-4 = B Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 5-6 = C Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 7-8 = D Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

prtExTsRxIoSignaling		1.3.6.1.4.1.164.3.1.4.2.1.1.12
IO - Rx Signaling per TS, for TSs having TS Type=Voice (agnTsType=voice(2)). It monitors what is received from IO port for the selected TS, for A,B,C,D Signaling Bits. Bit 1= LSB Bit 8= MSB Bit 1-2 = A Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 3-4 = B Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 5-6 = C Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 7-8 = D Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

prtCnfgAgenda		1.3.6.1.4.1.164.3.1.4.2.2
OBJECT IDENTIFIER

prtAgendaBehaviourTable		1.3.6.1.4.1.164.3.1.4.2.2.1
The write operation into the Table Objects is valid only to the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtAgendaBehaviourEntry

prtAgendaBehaviourEntry		1.3.6.1.4.1.164.3.1.4.2.2.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtAgendaBehaviourEntry

prtAgendaBehaviourCnfgIdx		1.3.6.1.4.1.164.3.1.4.2.2.1.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtAgendaBehaviourSltIdx		1.3.6.1.4.1.164.3.1.4.2.2.1.1.2
This parameter should be: - slot number for MX3000 - 255 = N/A for MX300/30.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtAgendaBehaviourPrtIdx		1.3.6.1.4.1.164.3.1.4.2.2.1.1.3
This parameter should be: - port number for MX300/30 - 100 = N/A for MX3000.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtAgendaBehaviourOnOff		1.3.6.1.4.1.164.3.1.4.2.2.1.1.4
Setting this command to on(3) enables the agenda function at module (3000) or port (300/30) level.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), off(2), on(3)

prtCnfgAgendaTable		1.3.6.1.4.1.164.3.1.4.2.2.2
This table allows the user to schedule the time a session is active per week basis.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtCnfgAgendaEntry

prtCnfgAgendaEntry		1.3.6.1.4.1.164.3.1.4.2.2.2.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtCnfgAgendaEntry

prtCnfgAgendaCnfgIdx		1.3.6.1.4.1.164.3.1.4.2.2.2.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtCnfgAgendaSltIdx		1.3.6.1.4.1.164.3.1.4.2.2.2.1.2
This attribute is equal to: -slot number for MX3000 -255 = N/A for MX300/30
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtCnfgAgendaPrtIdx		1.3.6.1.4.1.164.3.1.4.2.2.2.1.3
This attribute is equal to: - port number for MX300/30 - port number for MX3000. For example 1-4 in MHS-4 cards. - 100 = N/A for MX3000 when not used.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtCnfgAgendaDayIdx		1.3.6.1.4.1.164.3.1.4.2.2.2.1.4
This attribute for which day of the week this row applies.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	monday(1), tuesday(2), wednesday(3), thursday(4), friday(5), saturday(6), sunday(7)

prtCnfgAgendaSesId		1.3.6.1.4.1.164.3.1.4.2.2.2.1.5
The user may define 4 different active intervals per day.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..4

prtCnfgAgendaFrom		1.3.6.1.4.1.164.3.1.4.2.2.2.1.6
Start from time interval in seconds.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..86400

prtCnfgAgendaTo		1.3.6.1.4.1.164.3.1.4.2.2.2.1.7
To time interval in seconds.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..86400

prtGenCnfgTable		1.3.6.1.4.1.164.3.1.4.2.3
This table allows the user to configure general port parameters.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtGenCnfgEntry

prtGenCnfgEntry		1.3.6.1.4.1.164.3.1.4.2.3.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtGenCnfgEntry

prtGenCnfgIdx		1.3.6.1.4.1.164.3.1.4.2.3.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. The write operation is valid only to the TmpCnfg.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtGenCnfgSltIdx		1.3.6.1.4.1.164.3.1.4.2.3.1.2
This attribute indicates a unique slot position where the card is inserted.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

prtGenCnfgPrtIdx		1.3.6.1.4.1.164.3.1.4.2.3.1.3
This attribute indicates a unique external or internal port number. For MP: exPrt1 (1) .. exPrt16 (16) , notApplicable(100), inPrt1 (101) .. inPrt84 (184)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtGenCnfgLinkToSlot		1.3.6.1.4.1.164.3.1.4.2.3.1.4
This attribute indicates the slot of the ML card to which the IO port is mapped.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

prtGenCnfgLinkToPort		1.3.6.1.4.1.164.3.1.4.2.3.1.5
This attribute indicates the port in the prtGenCnfgLinkToSlot of the ML card to which the IO port is mapped. For MP: exPrt1 (1) , exPrt2 (2) , exPrt3 (3) , exPrt4 (4) , exPrt5 (5) , exPrt6 (6) , exPrt7 (7) , exPrt8 (8) , inPrt1 (101) , inPrt2 (102) , inPrt3 (103) , inPrt4 (104) , inPrt5 (105) , inPrt6 (106) , inPrt7 (107) , inPrt8 (108) , inPrt9 (109), inPrt10 (110), inPrt11 (111), inPrt12 (112), inPrt13 (113), inPrt14 (114), inPrt15 (115), inPrt16 (116), inPrt17 (117), inPrt18 (118), inPrt19 (119), inPrt20 (120), inPrt21 (121), inPrt22 (122), inPrt23 (123), inPrt24 (124), inPrt25 (125), inPrt26 (126), inPrt27 (127), inPrt28 (128), inPrt29 (129), inPrt30 (130), inPrt31 (131), inPrt32 (132), inPrt33 (133), inPrt34 (134), inPrt35 (135), inPrt36 (136), inPrt37 (137), inPrt38 (138), inPrt39 (139), inPrt40 (140), inPrt41 (141), inPrt42 (142), inPrt43 (143), inPrt44 (144), inPrt45 (145), inPrt46 (146), inPrt47 (147), inPrt48 (148), inPrt49 (149), inPrt50 (150), inPrt51 (151), inPrt52 (152), inPrt53 (153), inPrt54 (154), inPrt55 (155), inPrt56 (156), inPrt57 (157), inPrt58 (158), inPrt59 (159), inPrt60 (160), inPrt61 (161), inPrt62 (162), inPrt63 (163), inPrt64 (164), inPrt65 (165), inPrt66 (166), inPrt67 (167), inPrt68 (168), inPrt69 (169), inPrt70 (170), inPrt71 (171), inPrt72 (172), inPrt73 (173), inPrt74 (174), inPrt75 (175), inPrt76 (176), inPrt77 (177), inPrt78 (178), inPrt79 (179), inPrt80 (180), inPrt81 (181), inPrt82 (182), inPrt83 (183), inPrt84 (184), notApplicable (255)
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtGenCnfgPortId		1.3.6.1.4.1.164.3.1.4.2.3.1.6
IO Port Id for V5.1 use. This object is applicable only for part of the PSTN and ISDN IO ports. Generally, 0 is a valid value. Nevertheless, for ports that do not support this object, the value will be: notApplicable= 0
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..16777215

prtGenCnfgBusConnection		1.3.6.1.4.1.164.3.1.4.2.3.1.7
This object indicates the support of the card regarding Bus Connection. Same value for all ports of the card. partial = 2 Buses (AB) full = 4 Buses (ABCD) partial CD = 2 Buses CD Actually the support depends on the card's HW. But, since CL has to assign data on Buses even when the card is not installed, this object has to be configured. If the actual card installed will not match the value configured, an Alarm will be issued.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), partial(2), full(3), partialCD(4)

prtGenCnfgInbandMng		1.3.6.1.4.1.164.3.1.4.2.3.1.8
This object indicates whether Inband Management is used over the link.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), off(2), on(3)

prtGenCnfgInbandMngRoutProt		1.3.6.1.4.1.164.3.1.4.2.3.1.9
This object indicates the Inband Mng Routing Protocol of the port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), rip2(2), proprietaryRip(3), notApplicable(255)

prtGenCnfgProtectionMode		1.3.6.1.4.1.164.3.1.4.2.3.1.10
This object indicates the Protection Mode of the port. notApplicable- when Bus Protection Point=No. For VC-4/Omni card this object is supported RO.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), secondary(2), primary(3)

prtGenCnfgConnect		1.3.6.1.4.1.164.3.1.4.2.3.1.11
This object indicates whether the port should be considered in any of the mux algorithms.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3)

prtGenCnfgSignalingType		1.3.6.1.4.1.164.3.1.4.2.3.1.12
This object selects the Type of Signaling used by the port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	legacy(3), abcd(4), none(5)

prtCmprTable		1.3.6.1.4.1.164.3.1.4.3.1
A table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtCmprEntry

prtCmprEntry		1.3.6.1.4.1.164.3.1.4.3.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtCmprEntry

prtCmprTypIdx		1.3.6.1.4.1.164.3.1.4.3.1.1.1
This attribute indicates the Type of the Compressed being referred.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtCmprCnfgIdx		1.3.6.1.4.1.164.3.1.4.3.1.1.2
This attribute indicates the configuration to which the Compressed information is related.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtCmprVersion		1.3.6.1.4.1.164.3.1.4.3.1.1.3
This attribute indicates the version of the internal format of the Compressed data
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtCmprSltIdx		1.3.6.1.4.1.164.3.1.4.3.1.1.4
This attribute indicates a unique number of the slot position where the card is inserted. In the ?004 Unit the entries psB(2),clB(4),io6(10)..io(16) are not valid.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	psA(1), psB(2), clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

prtCmprPrtIdx		1.3.6.1.4.1.164.3.1.4.3.1.1.5
This attribute indicates a unique identifier of the port the compressed information relates to. Valid values: exPrt1 (1) .. exPrt16 (16) , inPrt1 (101) .. inPrt48 (148).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtCmprObj		1.3.6.1.4.1.164.3.1.4.3.1.1.6
This attribute is the compressed information itself.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

prtCmprStatisticObj		1.3.6.1.4.1.164.3.1.4.3.1.1.7
This attribute is the compressed statistics information itself.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

prtDlciCmprTable		1.3.6.1.4.1.164.3.1.4.3.2
A table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtDlciCmprEntry

prtDlciCmprEntry		1.3.6.1.4.1.164.3.1.4.3.2.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtDlciCmprEntry

prtDlciCmprCnfgIdx		1.3.6.1.4.1.164.3.1.4.3.2.1.1
This attribute indicates the configuration to which the Compressed information is related.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtDlciCmprVersion		1.3.6.1.4.1.164.3.1.4.3.2.1.2
This attribute indicates the version of the internal format of the Compressed data
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtDlciCmprSltIdx		1.3.6.1.4.1.164.3.1.4.3.2.1.3
This attribute indicates a unique number of the slot position where the module is inserted. In the ?004 Unit the entries psB(2),clB(4),io6(10)..io(16) are not valid.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

prtDlciCmprPrtIdx		1.3.6.1.4.1.164.3.1.4.3.2.1.4
This attribute indicates a unique identifier of the port the compressed information relates to. All the values are valid.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), exPrt5(5), exPrt6(6), exPrt7(7), exPrt8(8), exPrt9(9), exPrt10(10), inPrt1(101), inPrt2(102), inPrt3(103), inPrt4(104), inPrt5(105), inPrt6(106), inPrt7(107), inPrt8(108), inPrt9(109), inPrt10(110), inPrt11(111), inPrt12(112)

prtDlciCmprDlciIdx		1.3.6.1.4.1.164.3.1.4.3.2.1.5
This attribute indicates a unique identifier of the Dlci the compressed information relates to. The values are between 16 - 991.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtDlciCmprObj		1.3.6.1.4.1.164.3.1.4.3.2.1.6
This attribute is the compressed information itself.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

prtAlarmsCmprTable		1.3.6.1.4.1.164.3.1.4.3.3
A table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtAlarmsCmprEntry

prtAlarmsCmprEntry		1.3.6.1.4.1.164.3.1.4.3.3.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtAlarmsCmprEntry

prtAlarmsCmprVersion		1.3.6.1.4.1.164.3.1.4.3.3.1.1
This attribute indicates the version of the internal format of the Compressed data
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtAlarmsCmprAlarmSlot		1.3.6.1.4.1.164.3.1.4.3.3.1.2
This attribute indicates the desired slot position. In the ?004 Unit the entries PsB(2),ClB(4),io6(10)..io(16) are not valid. For Stand-alone units, notApplicable(255) will appear.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtAlarmsCmprAlarmPort		1.3.6.1.4.1.164.3.1.4.3.3.1.3
This attribute indicates a unique identifier of the port the alarm applies to. All the values are valid. No alarms exist for a non-existing port. IP Bundles are considered a port too, for this matter.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtAlarmsCmprAlarmIdx		1.3.6.1.4.1.164.3.1.4.3.3.1.4
A unique number to identify an entry in the alarm status table of the agent.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtAlarmsCmprObj		1.3.6.1.4.1.164.3.1.4.3.3.1.5
This attribute is the compressed information itself.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

prtSExHsfStatTable		1.3.6.1.4.1.164.3.2.3.1.6
A table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtSExHsfStatEntry

prtSExHsfStatEntry		1.3.6.1.4.1.164.3.2.3.1.6.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtSExHsfStatEntry

prtSExHsfSltIdx		1.3.6.1.4.1.164.3.2.3.1.6.1.1
This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

prtSExHsfPrtIdx		1.3.6.1.4.1.164.3.2.3.1.6.1.2
This attribute indicates a unique port number.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), exPrt5(5), exPrt6(6), exPrt7(7), exPrt8(8), exPrt9(9), exPrt10(10), exPrt11(11), exPrt12(12)

prtSExHsfInterfaceTyp		1.3.6.1.4.1.164.3.2.3.1.6.1.3
This attribute indicates a unique interface type of a selected port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), v35(2), rs422(3)

prtSExHsfRts		1.3.6.1.4.1.164.3.2.3.1.6.1.4
This attribute indicates a unique RTS control signal state.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), notActive(2), active(3)

prtIsdnStatusTable		1.3.6.1.4.1.164.3.2.3.1.16
This table contains ISDN Statistics parameters that do not appear in the standard MIBs or for agents that don't support the standard Index of Call Set Up Time.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtIsdnStatusEntry

prtIsdnStatusEntry		1.3.6.1.4.1.164.3.2.3.1.16.1
Entries for ISDN Statistics parameters that do not appear in the standard MIBs or for agents that don't support the standard Index of Call Set Up Time.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtIsdnStatusEntry

prtIsdnStatusDspMode		1.3.6.1.4.1.164.3.2.3.1.16.1.1
The DSP can be in one of the following Modes: Voice, Idle, Fax, Voice Band Data (VBD)- Modem.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	voice(2), idle(3), fax(4), vbd(5)

prtIsdnStatusCallState		1.3.6.1.4.1.164.3.2.3.1.16.1.2
The state that the current call is in.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	present(2), overlapReceive(3), incoming(4), receive(5), initiated(6), overlapSend(7), outGoingProceed(8), callDeliver(9), active(10), disconnectIndicate(11), releaseRequest(12), disconnectReq(13), notActive(14)

prtIsdnStatusCallingNumber		1.3.6.1.4.1.164.3.2.3.1.16.1.3
This is the local Number (ISDN Address) associated with this entry.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

prtIsdnStatusCalledNumber		1.3.6.1.4.1.164.3.2.3.1.16.1.4
This is the remote Number (ISDN Address) associated with this entry.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

prtIsdnStatusCalledIP		1.3.6.1.4.1.164.3.2.3.1.16.1.5
This is the remote IP Address associated with this entry.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

prtIsdnStatusCallDirection		1.3.6.1.4.1.164.3.2.3.1.16.1.6
Attribute indicating the Direction of the Call. The value of notApplicable will be used for example when prtIsdnStatusCallState = notActive(14).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), incoming(2), outgoing(3)

cnfgMdlMux		1.3.6.1.4.1.164.3.2.2.1
OBJECT IDENTIFIER

mdlPbxFramerCnfg		1.3.6.1.4.1.164.3.2.2.1.1
OBJECT IDENTIFIER

mdlPbxFramerCnfgTable		1.3.6.1.4.1.164.3.2.2.1.1.1
This table contains parameters relevant to a module belonging to a digital voice system, except mdlPbxFraEnhEcho which is relevant also for analog cards.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MdlPbxFramerCnfgEntry

mdlPbxFramerCnfgEntry		1.3.6.1.4.1.164.3.2.2.1.1.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	MdlPbxFramerCnfgEntry

mdlPbxFraCnfgIdx		1.3.6.1.4.1.164.3.2.2.1.1.1.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

mdlPbxFraSltIdx		1.3.6.1.4.1.164.3.2.2.1.1.1.1.2
The slot relevant to this module.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

mdlPbxFraEnhEcho		1.3.6.1.4.1.164.3.2.2.1.1.1.1.3
Refers to external ports of an analogue module and to the internal ports of the other mvc4 types of modules. ms16(3) means that the four voice ports have enhanced echo of 16ms. ms32(4) means that the two first ports have enhanced echo of 32 ms while the last two ports have no enhanced echo.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), disabled(2), ms16(3), ms32(4)

mdlPbxFraTSGroupAss		1.3.6.1.4.1.164.3.2.2.1.1.1.1.4
In case of T1 modules: group1=(1,2,3,4), ...., group6=(21,22,23,24) while in case of E1 modules: - If prtExPh1MlLineType=g732sE1 or g732sE1CRC: group1=(1,2,3,4),..,group4=(13,14,15,17), group5=(18,19,20,21),...,group7=(26,27,28,29) group8=(30,31). - If prtExPh1MlLineType=g732nE1 or g732nE1CRC: group1=(1,2,3,4),..,group4=(13,14,15,16), group5=(17,18,19,20),...,group7=(25,26,27,28) group8=(29,30,31).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	group1(1), group2(2), group3(3), group4(4), group5(5), group6(6), group7(7), group8(8), notApplicable(255)

mdlPbxFraSignalMode		1.3.6.1.4.1.164.3.2.2.1.1.1.1.5
Refers to the signaling mode of the Framer module. tieTrunk(2), tieInvert(3), casTrans(4) are standard coding of the signaling protocol. casTrans(4) is Channel Associated Signaling (the signaling is within the channels time slot). ccsTrans(6) is Transparent Common Channel Signaling (the signaling is not within the channels time slot - a TS for signaling is used). userDefined(5) allows the user to define the signaling protocol he wants. In this case, the next two MIB fields are relevant.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), tieTrunk(2), tieInvert(3), casTrans(4), userDefined(5), ccsTrans(6), noSignaling(7)

mdlPbxFraSignalVector		1.3.6.1.4.1.164.3.2.2.1.1.1.1.6
In the case of mdlPbxFraSignalMode = userDefined(5), this field defines the A,B,C Bits. D bit is supplied for future versions. Bit 1 = Bit A ON Hook - Local Bit 2 = Bit B ON Hook - Local Bit 3 = Bit C ON Hook - Local Bit 4 = Bit D ON Hook - Local Bit 5 = Bit A OFF Hook - Local Bit 6 = Bit B OFF Hook - Local Bit 7 = Bit C OFF Hook - Local Bit 8 = Bit D OFF Hook - Local Bit 9 = Bit A ON Hook - Remote Bit 10 = Bit B ON Hook - Remote Bit 11 = Bit C ON Hook - Remote Bit 12 = Bit D ON Hook - Remote Bit 13 = Bit A OFF Hook - Remote Bit 14 = Bit B OFF Hook - Remote Bit 15 = Bit C OFF Hook - Remote Bit 16 = Bit D OFF Hook - Remote In conjunction with the Mask, mdlPbxFraSignalMask, it is possible to compute the signal mode.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

mdlPbxFraSignalMask		1.3.6.1.4.1.164.3.2.2.1.1.1.1.7
In the case of mdlPbxFraSignalMode = userDefined(5), this field defines the 'don't care' A,B,C Bits. D bit is supplied for future versions. Bit 1 = Bit A ON Hook - Local Bit 2 = Bit B ON Hook - Local Bit 3 = Bit C ON Hook - Local Bit 4 = Bit D ON Hook - Local Bit 5 = Bit A OFF Hook - Local Bit 6 = Bit B OFF Hook - Local Bit 7 = Bit C OFF Hook - Local Bit 8 = Bit D OFF Hook - Local Bit 9 = Bit A ON Hook - Remote Bit 10 = Bit B ON Hook - Remote Bit 11 = Bit C ON Hook - Remote Bit 12 = Bit D ON Hook - Remote Bit 13 = Bit A OFF Hook - Remote Bit 14 = Bit B OFF Hook - Remote Bit 15 = Bit C OFF Hook - Remote Bit 16 = Bit D OFF Hook - Remote.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

mdlPbxFraFramerSlot		1.3.6.1.4.1.164.3.2.2.1.1.1.1.8
Slot where is sitting the Framer.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

mdlPbxFraSignaling		1.3.6.1.4.1.164.3.2.2.1.1.1.1.9
Signaling - describes the way the signaling ABCD bits pass from the local extension to the remote extension and vice-versa. endToEnd = the signaling ABCD bits pass without change from local to remote extension. localTermination = the signaling ABCD bits received from the local extension are translated to different ON Hook/OFF Hook bit values and then passed to remote extension. This is relevant when the Local and Remote ON Hook/OFF Hook values are different.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), endToEnd(2), localTermination(3)

mdlPbxFraTransSigTs		1.3.6.1.4.1.164.3.2.2.1.1.1.1.10
This is the Time Slot that is used for Transparent CCS signaling. The values of this TS are 1-24 for T1 & 1-31 for E1. The default for E1 is 16 & for T1 it is 24. If no signaling is used then the TS should be 255 (None).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

mdlProtIpTable		1.3.6.1.4.1.164.3.2.2.1.2
This table contains Protected IP Addresses for ML-IP cards when working in IP Ring Mode.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MdlProtIpEntry

mdlProtIpEntry		1.3.6.1.4.1.164.3.2.2.1.2.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	MdlProtIpEntry

mdlProtIpCnfgIdx		1.3.6.1.4.1.164.3.2.2.1.2.1.1
This attribute indicates the Idx of the Cnfg being accessed. Idx 255 relates to the TmpCnfg. For Agents having several configuration, Write operation is allowed only to the Temporary Configuration.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

mdlProtIpSlotIdx		1.3.6.1.4.1.164.3.2.2.1.2.1.2
This attribute indicates a unique slot position where the module is inserted. In the 2104 Unit the entries io6(10)..io16) are not valid.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

mdlProtIpAddress		1.3.6.1.4.1.164.3.2.2.1.2.1.3
A Protected IP address.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

mdlProtIpRowStatus		1.3.6.1.4.1.164.3.2.2.1.2.1.4
This parameter allows creating/deleting entries of this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

statMdlMux		1.3.6.1.4.1.164.3.2.2.2
OBJECT IDENTIFIER

mdlStatTable		1.3.6.1.4.1.164.3.2.2.2.1
A table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MdlStatEntry

mdlStatEntry		1.3.6.1.4.1.164.3.2.2.2.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	MdlStatEntry

mdlStatSltIdx		1.3.6.1.4.1.164.3.2.2.2.1.1.1
A unique number to identify a slot position in the mux. In the 2104 Unit the entries psB(2),clB(4),io6(10)..io12(16) are not valid.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	psA(1), psB(2), clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

mdlStatHostIP		1.3.6.1.4.1.164.3.2.2.2.1.1.2
The host interface IP address when DHCP Client=Yes. This object is relevant only when DHCP Client=Yes
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

mdlStatHostMask		1.3.6.1.4.1.164.3.2.2.2.1.1.3
The host interface subnet mask when DHCP Client=Yes. This object is relevant only when DHCP Client=Yes
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

mdlStatDefaultGateway		1.3.6.1.4.1.164.3.2.2.2.1.1.4
Default Gateway's IP Address when DHCP Client=Yes. This object is relevant only when DHCP Client=Yes
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

prtExClCnfgTable		1.3.6.1.4.1.164.3.2.3.2.1.1
A table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtExClCnfgEntry

prtExClCnfgEntry		1.3.6.1.4.1.164.3.2.3.2.1.1.1
All the entries at this table are identical (have the same value) for all the configurations (1..100) except the TmpCnfg. The write operation into the Table Objects is valid only to the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtExClCnfgEntry

prtExClCnfgIdx		1.3.6.1.4.1.164.3.2.3.2.1.1.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtExClSltIdx		1.3.6.1.4.1.164.3.2.3.2.1.1.1.2
This attribute indicates a unique slot position where the card is inserted. Because the second Cl is only for redundancy, all the parameters are identical in the two modules, i.e. change of any parameter in one module will change automatically the value of the other module.. In the ?004 Unit the entry clB(4) is not valid.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	clA(3), clB(4), notApplicable(255)

prtExClPrtIdx		1.3.6.1.4.1.164.3.2.3.2.1.1.1.3
This attribute indicates a unique port number.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	exPrt1(1), exPrt2(2)

prtExClUsage		1.3.6.1.4.1.164.3.2.3.2.1.1.1.4
This attribute indicates what is the usage of the port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), noUse(2), nmsSlip(3), nmsPpp(4), muxSlip(5), muxPpp(6), terminal(7)

prtExClRate		1.3.6.1.4.1.164.3.2.3.2.1.1.1.5
This attribute indicates the operation rate of the port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	r300Bps(1), r1200Bps(2), r2400Bps(3), r4800Bps(4), r9600Bps(5), r19200Bps(6), r38400Bps(7), r57600Bps(8), r115200Bps(9)

prtExClDataBits		1.3.6.1.4.1.164.3.2.3.2.1.1.1.6
This attribute indicates the number of data bits in async frame
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	dataBits7Bits(1), dataBits8Bits(2)

prtExClParity		1.3.6.1.4.1.164.3.2.3.2.1.1.1.7
This attribute indicates if the parity operation mode in async frame
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	odd(1), even(2), none(3)

prtExClStopBits		1.3.6.1.4.1.164.3.2.3.2.1.1.1.8
This attribute indicates the minimum number of stop bits in the tx async frame
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	stopBits1Bit(1), stopBits1dot5Bits(2), stopBits2Bits(3)

prtExClRoutingProtocol		1.3.6.1.4.1.164.3.2.3.2.1.1.1.9
This attribute indicates the routing protocol of the port. When prtExClUsage is nmsSlip or nmsPpp - all values are applicable . Else - only 'none' is applicable.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), rip2(2)

prtExClEnabled		1.3.6.1.4.1.164.3.2.3.2.1.1.1.10
This attribute indicates if Ethernet port of CL is enabled or not for management. It is applicable only on the ETH port of the CL, when the MP includes an ML-IP card. disabled - will happen when there is Inband Management via the ML-IP link/s enabled - will happen when ML-IP link/s is not used for Inband Management, but CL's ETH port .
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), disabled(2), enabled(3)

prtExPh1MlCnfgTable		1.3.6.1.4.1.164.3.2.3.2.2.1
- For products supporting more than one configuration, the write operation into the Table is valid only to the TmpCnfg entry. - For products that do not support configurations, the write operation into the Table will be to prtExPh1MlCnfgIdx=1.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtExPh1MlCnfgEntry

prtExPh1MlCnfgEntry		1.3.6.1.4.1.164.3.2.3.2.2.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtExPh1MlCnfgEntry

prtExPh1MlCnfgIdx		1.3.6.1.4.1.164.3.2.3.2.2.1.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtExPh1MlSltIdx		1.3.6.1.4.1.164.3.2.3.2.2.1.1.2
This attribute indicates a unique slot position where the module is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid. For the Vmux2100 Main Board notApplicable (1) is used.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

prtExPh1MlPrtIdx		1.3.6.1.4.1.164.3.2.3.2.2.1.1.3
This attribute indicates a unique port number. MP-2100/2200: MTML-1/E1 and MTML-1/T1 cards have only one external interface. inPrt1, inPrt2 - for MTML-H/2E1 and HSH cards. inPrt1..inPrt4 - for MTML-E2 and MSL-4 cards. exPrt2..exPrt4 - for MTML-4 cards and others exPrt1..exPrt8 - for ML-8 cards. inPrt1..inPrt8 - for MSL-8 and VF-30 card family. MP-104/204: only exPrt3 (3) is applicable. MP-4100: intPrt1...intPrt84 - for CLX cards. For other products' index see their specification.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), exPrt5(5), exPrt6(6), exPrt7(7), exPrt8(8), exPrt9(9), exPrt10(10), exPrt11(11), exPrt12(12), exPrt13(13), exPrt14(14), exPrt15(15), exPrt16(16), exPrt17(17), exPrt18(18), inPrt1(101), inPrt2(102), inPrt3(103), inPrt4(104), inPrt5(105), inPrt6(106), inPrt7(107), inPrt8(108), inPrt9(109), inPrt10(110), inPrt11(111), inPrt12(112), inPrt13(113), inPrt14(114), inPrt15(115), inPrt16(116), inPrt17(117), inPrt18(118), inPrt19(119), inPrt20(120), inPrt21(121), inPrt22(122), inPrt23(123), inPrt24(124), inPrt25(125), inPrt26(126), inPrt27(127), inPrt28(128), inPrt29(129), inPrt30(130), inPrt31(131), inPrt32(132), inPrt33(133), inPrt34(134), inPrt35(135), inPrt36(136), inPrt37(137), inPrt38(138), inPrt39(139), inPrt40(140), inPrt41(141), inPrt42(142), inPrt43(143), inPrt44(144), inPrt45(145), inPrt46(146), inPrt47(147), inPrt48(148), inPrt49(149), inPrt50(150), inPrt51(151), inPrt52(152), inPrt53(153), inPrt54(154), inPrt55(155), inPrt56(156), inPrt57(157), inPrt58(158), inPrt59(159), inPrt60(160), inPrt61(161), inPrt62(162), inPrt63(163), inPrt64(164), inPrt65(165), inPrt66(166), inPrt67(167), inPrt68(168), inPrt69(169), inPrt70(170), inPrt71(171), inPrt72(172), inPrt73(173), inPrt74(174), inPrt75(175), inPrt76(176), inPrt77(177), inPrt78(178), inPrt79(179), inPrt80(180), inPrt81(181), inPrt82(182), inPrt83(183), inPrt84(184)

prtExPh1MlConnect		1.3.6.1.4.1.164.3.2.3.2.2.1.1.4
This attribute indicates whether the port should be considered in any of the mux algorithms. It also affects all the card considerations because it may indicate that the module has only one physical interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3)

prtExPh1MlLineType		1.3.6.1.4.1.164.3.2.3.2.2.1.1.5
This attribute is the line type parameter for T1/E1 interface. The user should select only the values which are relevant to the specific port: (2),(3), (8) - for T1 port (4)..(7), (9) - for E1 port. (101) framed - This value does not exist in standard MIB and is used for a non-standard E1 port that doesn't has real framer. Note: for old devices, g732unframed(8) was used as E1 Unframed. That was because at the time this value did not exist in the standard MIB (RFC-1406), so we added it in private MIB. Now that it was added to standard MIB, private MIB was updated as well. This parameter has the same values as dsx1LineType in DS1 MIB (RFC-3895). The parameters in dsx1LineType are: other (1) esfT1 dsx1ESF (2) sfT1 dsx1D4 (3) g732nE1 dsx1E1 (4) g732nE1CRC dsx1E1-CRC (5) g732sE1 dsx1E1-MF (6) g732sE1CRC dsx1E1-MF-CRC (7) g732unframed dsx1Unframed (8) --from RFC-3895 e1Unframed dsx1E1Unframed (9) --from RFC-3895
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	esfT1(2), sfT1(3), g732nE1(4), g732nE1CRC(5), g732sE1(6), g732sE1CRC(7), g732unframed(8), e1Unframed(9), framed(101)

prtExPh1MlLineCode		1.3.6.1.4.1.164.3.2.3.2.2.1.1.6
This attribute is the line code parameter used for T1/E1 interface. The user should select only the parameters which are relevant to the specific card: T1 line code parameters for MPH.1/T1 E1 line code parameters for MPH.1/E1. This parameter has the same values as dsx1LineCoding in T1/E1 MIB (RFC-1406). The parameters in dsx1LineCoding are: dsx1JBZS (1) dsx1B8ZS (2) dsx1HDB3 (3) dsx1ZBTSI (4) dsx1AMI (5) other (6)
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	b7T1(1), b8zsT1(2), transT1(3), hdb3E1(4), notApplicable(255)

prtExPh1MlLineLen		1.3.6.1.4.1.164.3.2.3.2.2.1.1.7
This attribute is the line length parameter used only for T1/DSU interfaces. lenXXXpXXXft = len-XXX-XXXft.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unknown(1), len0p133ft(2), len134p266ft(3), len267p399ft(4), len400p533ft(5), len534p655ft(6), lenFcc68(7), notApplicable(255)

prtExPh1MlRestoreTime		1.3.6.1.4.1.164.3.2.3.2.2.1.1.8
The time passing from the disappearance of the loss of synchronization condition (red alarm) to the restoration of normal service. The options 1secFast(2) and 10sec62411(3) for E1 interfaces are proprietary implementation of the T1 standard to the E1 interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	restoreT1secFast(2), restoreT10sec62411(3), ccittE1(4)

prtExPh1MlTxGain		1.3.6.1.4.1.164.3.2.3.2.2.1.1.9
This attribute is the tx gain parameter used only for T1/CSU interfaces.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), txGain0db(2), txGain7dot5db(3), txGain15db(4), txGain22dot5db(5)

prtExPh1MlRxSensitivity		1.3.6.1.4.1.164.3.2.3.2.2.1.1.10
This attribute is the rx line sensitivity parameter. low26dBm, high36dBm - applicable for T1-CSU shortHaul, longHaul - applicable for MTML-4 cards low15dbm was added for vmux110/210 T1 ports.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), low26dBm(2), high36dBm(3), shortHaul(4), longHaul(5), low15dbm(6)

prtExPh1MlIdleCode		1.3.6.1.4.1.164.3.2.3.2.2.1.1.11
Determines the code for transmission in empty time slots. Type value(00-FFH), Excluding 0H,8H,10H,12H,21H,24H,42H,49H, 84H,92H
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtExPh1MlTdmTrunk		1.3.6.1.4.1.164.3.2.3.2.2.1.1.12
This attribute indicates whether the port is used to transfer TDM cards data and through which Bus.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	linkA(1), linkB(2), none(3), notApplicable(255)

prtExPh1MlClkMode		1.3.6.1.4.1.164.3.2.3.2.2.1.1.13
Defines the clock operation mode of the T1/E1 interface. Ports that are connected to the TDM Buses must be in nodalTiming(3) clock mode.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	internalLocal(1), loopBackLocal(2), nodalTiming(3), loopBackFromLink(4), loopBackFromChannel(5), loopbackFromSystem(6)

prtExPh1MlMfClkSrcSlt		1.3.6.1.4.1.164.3.2.3.2.2.1.1.14
This attribute indicates whether the port Tx multiframe is synchronized with Rx multiframe of another port and the slot position of that port. This operation is required in order to bypass signaling of PCM voice channels. Its value is always local(2) when the port isn't connected to any TDM bus. When it's value is local(2) there is no meaning to 'prtExPh1MlMfClkSrcPrt' parameter. In the ?004 Unit the entries io6(10)..io16) are not valid
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), local(2), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

prtExPh1MlMfClkSrcPrt		1.3.6.1.4.1.164.3.2.3.2.2.1.1.15
A unique number to identify a port position in the mux. It has no effect when the prtExPh1MlMfClkSrcSlt selected is Local. inPrt1 - for MTML-H/E1 cards.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	exPrt1(1), exPrt2(2), inPrt1(101), notApplicable(255)

prtExPh1MlFdlType		1.3.6.1.4.1.164.3.2.3.2.2.1.1.16
A unique number to identify the side of the FDL operation. Normal: 'response' for the user side and 'command' for the PTT side. Applicable only when working with ESF-T1 link
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), response(2), command(3)

prtExPh1MlInbandMng		1.3.6.1.4.1.164.3.2.3.2.2.1.1.17
A unique number to identify an Inband management over the link.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), fdlOrTs0(3), dedicatedTs(4), dedicatedPpp(5), dedicatedFr(6), notApplicable(255)

prtExPh1MlInbandMngRate		1.3.6.1.4.1.164.3.2.3.2.2.1.1.18
A unique number to identify the rate of the Inband management (Kbps). E1 port - it is not applicable when prtExPh1MlInbandMng selected is off. T1 port - it is not applicable when prtExPh1MlInbandMng selected is off OR fdlOrTs0.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), r4k(2), r8k(3), r12k(4), r16k(5), r32k(6), r64k(7), r20k(8)

prtExPh1MlRedundType		1.3.6.1.4.1.164.3.2.3.2.2.1.1.19
This object determines the ML redundancy type: none - no ML redundacy dualCableAIS - each ML card is connected by a separate dualCableParallelTx cable to the other MUX (two cables connect two MUXes). There are two types of dual redundancy. yCable - Y cable is connected to both ML cards (one cable connects two MUXes). Default=none When only one ML card exists, the type can be only 'none'. The value should be the same for both ML slots.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), dualCableAIS(2), yCable(3), dualCableParallelTx(4)

prtExPh1MlRedundSlot		1.3.6.1.4.1.164.3.2.3.2.2.1.1.20
This object indicates the slot containing the redundacy ML card, coupled with the current ML (prtExPh1MlSltIdx). When prtExPh1MlRedundType=none (no ML redundancy) this object will be 'notApplicable'. In the ?004 Unit the entries io6(10)..io12(16) are not valid When value is not 'none', it should be mutual to the redundant ML slot.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

prtExPh1MlRedundPort		1.3.6.1.4.1.164.3.2.3.2.2.1.1.21
This object indicates the redundacy ML port, coupled with the current ML port (prtExPh1MlPrtIdx). When prtExPh1MlRedundType=none (no ML redundancy) this object will be 'notApplicable'. When value is not 'none', it should be mutual to the redundant ML port. inPrt1 - for MTML-H/E1 cards. inPrt1..inPrt4 - for MTML-E2 cards. exPrt2..exPrt4 - for MTML-4 cards.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), inPrt1(101), inPrt2(102), inPrt3(103), inPrt4(104), notApplicable(255)

prtExPh1MlRedundRecTime		1.3.6.1.4.1.164.3.2.3.2.2.1.1.22
Redundancy Recovery Time (sec). After switching the ML card to the current (prtExPh1MlSltIdx), the next ML switch can be performed only after a minimum time, indicated by this object.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..99

prtExPh1MlInbandMngRoutProt		1.3.6.1.4.1.164.3.2.3.2.2.1.1.23
This attribute indicates the Inband Mng routing protocol of the port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), rip2(2), proprietary(3), proprietaryNoNmsTx(4)

prtExPh1MlIfType		1.3.6.1.4.1.164.3.2.3.2.2.1.1.24
Interface type of the port. For T1 - csu, dsu are the valid values For E1 - dsu, ltu are the valid values.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), csu(2), dsu(3), ltu(4)

prtExPh1MlMultiplier		1.3.6.1.4.1.164.3.2.3.2.2.1.1.25
The data rate of each TS. The multiplier values can be 56 kbps or 64 kbps.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), br56(2), br64(3)

prtExPh1MlSupportedTS		1.3.6.1.4.1.164.3.2.3.2.2.1.1.26
Number of Supported Time Slots by the agent. For Vmux-110 there is HW that supports less than 31/24 Time Slots for the E1/T1 port.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtExPh1MlImpedance		1.3.6.1.4.1.164.3.2.3.2.2.1.1.27
The Line Impedance. For T1 (always balanced), impedance is 100 ohm. For E1: - balanced = 120 ohm - unbalanced = 75 ohm.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), unbalanced(2), balanced(3)

prtExPh1MlQ50BwControl		1.3.6.1.4.1.164.3.2.3.2.2.1.1.28
This object enables configuration of Q.50 Bandwidth Control on the port. If the bandwidth exceeds a certain threshold it is possible to disable new calls in the PBX via Q.50 protocol. Q.50 supports only E1 ports with Line Types: E1-MF (G.732S), E1-CRC-MF(G.732SCRC ) It does not support T1 ports. Annex A - the basic type of Q.50 which focuses only on the bandwidth control. Can use one of the following pairs of signaling bits: A&B or C&D. Annex B - Expansion of Annex A which includes also call release messages and Maintenance Messages. Uses A&B bits only.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(2), annexA(3), annexB(4)

prtExPh1MlQ50SignalPair		1.3.6.1.4.1.164.3.2.3.2.2.1.1.29
Q.50 Signaling bits Pair that is currently in use: A&B bits or C&D bits. For Annex B it will always be: aAndB (2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), aAndB(2), cAndD(3)

prtExPh1MlInternalSwitch		1.3.6.1.4.1.164.3.2.3.2.2.1.1.30
This parameter shows whether the data will be transferred from one port to the other port within the same group of 2 ports. The default value is: Enable. Disable value might be necessary for security implementations or for ring applications. For Vmux-2100 device this parameter is used on the Channelized Cards. Both ports in each group should have the same value for this parameter.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(2), enable(3)

prtExPh1MlSigService		1.3.6.1.4.1.164.3.2.3.2.2.1.1.31
Signaling Service given by this link. notApplicable - for T1 links normal - usual Signaling advanced - V5 Signaling.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), normal(2), advanced(3)

prtExPh1MlFragmentSize		1.3.6.1.4.1.164.3.2.3.2.2.1.1.32
This parameter indicates the maximum number of bytes permitted in a packet send over the Link. Exceeding this size will cause packet fragmentation.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtExPh1MlTsTable		1.3.6.1.4.1.164.3.2.3.2.2.2
The write operation into the Table Objects is valid only to the TmpCnfg entry, except prtExPh1MlTsTest that will be written directly to the Active Configuration.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtExPh1MlTsEntry

prtExPh1MlTsEntry		1.3.6.1.4.1.164.3.2.3.2.2.2.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtExPh1MlTsEntry

prtExPh1MlTsCnfgIdx		1.3.6.1.4.1.164.3.2.3.2.2.2.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtExPh1MlTsSltIdx		1.3.6.1.4.1.164.3.2.3.2.2.2.1.2
This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid. For the Vmux2100 Main Board notApplicable (255) is used.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

prtExPh1MlTsPrtIdx		1.3.6.1.4.1.164.3.2.3.2.2.2.1.3
This attribute indicates a unique port number. MPH.1/E1 and MPH.1/T1 cards have only one external interface. exPrt2 - for ME1-2, MT1-2 and mhsPri cards. exPrt3, exPrt4 - for mhsPri cards. inPrt1 - for MTML-H/E1 cards.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), exPrt5(5), exPrt6(6), exPrt7(7), exPrt8(8), exPrt9(9), exPrt10(10), exPrt11(11), exPrt12(12), exPrt13(13), exPrt14(14), exPrt15(15), exPrt16(16), exPrt17(17), exPrt18(18), inPrt1(101), inPrt2(102), inPrt3(103), inPrt4(104), inPrt5(105), inPrt6(106), inPrt7(107), inPrt8(108), inPrt9(109), inPrt10(110), inPrt11(111), inPrt12(112), inPrt13(113), inPrt14(114), inPrt15(115), inPrt16(116), inPrt17(117), inPrt18(118), inPrt19(119), inPrt20(120)

prtExPh1MlTsIdx		1.3.6.1.4.1.164.3.2.3.2.2.2.1.4
This attribute indicates a unique time slot position. The valid time slots are 1..24 for T1 Card and 1..31 for E1 interface. In G732S-E1 lines time slot 16 is not valid for data, it is dedicated for multiframe synchronization bits and voice signaling.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtExPh1MlTsIConSlot		1.3.6.1.4.1.164.3.2.3.2.2.2.1.5
This attribute indicates whether the specified time slot is connected/routed internally in the Agent and to which card it is connected. In the ?004 Unit the entries io6(10)..io16) are not valid. split - will be used when the Src TS is connected to more than one slot OR more than one port (each needing less than a whole TS).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unknown(1), noConnect(2), split(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

prtExPh1MlTsIConPrt		1.3.6.1.4.1.164.3.2.3.2.2.2.1.6
This attribute indicates the internally (In Mux) connected/routed port. For MP, the values will be: { exPrt1 (1) , exPrt2 (2) , exPrt3 (3) , exPrt4 (4) , exPrt5 (5) , exPrt6 (6) , exPrt7 (7) , exPrt8 (8) , exPrt9 (9) , exPrt10 (10) , exPrt11 (11) , exPrt12 (12) , noConnect (100), inPrt1 (101) , inPrt2 (102) , inPrt3 (103) , inPrt4 (104) , inPrt5 (105) , inPrt6 (106) , inPrt7 (107) , inPrt8 (108) , inPrt9 (109) , inPrt10 (110) , inPrt11 (111) , inPrt12 (112) } For other products see specific values at spec.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtExPh1MlTsIConTs		1.3.6.1.4.1.164.3.2.3.2.2.2.1.7
This attribute indicates a unique time slot position. The valid time slots are 1..24 for T1 Card and 1..31 for E1 interface. In G732S-E1 lines time slot 16 is not valid for data, it is dedicated to multiframe synchronization and voice signaling.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtExPh1MlTsExt		1.3.6.1.4.1.164.3.2.3.2.2.2.1.8
A pointer to an extension of this table: prtExTsSplitTable. - If prtExPh1MlTsIConSlot='split', its value should be set to the OBJECT IDENTIFIER of the prtExTsSplitTable, with its relevant CnfgIdx, SltIdx, PrtIdx, TsIdx and 1st TsBit. - If prtExPh1MlTsIConSlot is not 'split', its value should be set to the OBJECT IDENTIFIER { 0 0 }.
Status: current	Access: read-only
OBJECT-TYPE
	OBJECT IDENTIFIER

prtExPh1MlTsTest		1.3.6.1.4.1.164.3.2.3.2.2.2.1.9
This attribute indicates a test to be activated on the selected TS. It is applicable only when prtSTstCmd=testPerTS(31). notApplicable - when prtSTstCmd is NOT testPerTS(31). none - no test is applied for the selected TS. split - when the tests are per Bit of the selected TS.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), localLoop(2), remoteLoop(3), remoteBert(8), localToneInjection(9), remoteToneInjection(18), localBert(30), split(254), notApplicable(255)

prtExPh1MlTsType		1.3.6.1.4.1.164.3.2.3.2.2.2.1.10
The Time Slot Type. Transparent - means that the Time Slot will be Rx/Tx as is without processing it. If the device requires more than 1 unique data or ss7 Time Slot, options with numbers can be used like: data...data4. Each numbered Type can go to a different destination. ss7n2 - means the 2nd group of ss7 Time Slots. data2,data3, data4 mean group 2,3,4 of Data Time Slots. subCh1...subCh8 mean Sub Channel 1...8, respectively. trau, qmux, dynamic, signaling - are used by GSM devices.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noConnect(2), data(3), voice(4), cas(5), ss7(6), transparent(7), data2(8), data3(9), data4(10), ss7n2(11), hdlcV2Compatible(12), subCh1(13), subCh2(14), subCh3(15), subCh4(16), subCh5(17), subCh6(18), subCh7(19), subCh8(20), trau(21), qmux(22), dynamic(23), signaling(24), notApplicable(255)

prtExPh1MlTsBundle		1.3.6.1.4.1.164.3.2.3.2.2.2.1.11
The number of the bundle containing this Time Slot. If no bundle exists for this TS or the bundle number is irrelevant, the value will be 0.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtExPh1MlTsTestDuration		1.3.6.1.4.1.164.3.2.3.2.2.2.1.12
This attribute indicates the maximum duration of executing a test on the specific TS. This entry applies to all the test operations. For the Vmux2100 the values are: 0 - 60 seconds. A zero value specifies no time limitation. When the test isn't active, the agent initiates this object to 2 when the duration is needed and to 0 if its not required. The user should set this parameter after setting the 'prtExPh1MlTsTest' parameter.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtExPh1MlTsSubChType		1.3.6.1.4.1.164.3.2.3.2.2.2.1.13
The Time Slot Sub-Channel Type. This variable is relevant only when Time-Slot Type is SubCh (e.g. prtExPh1MlTsType = subCh1...subCh8).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	hdlc(1), transparent(2), notApplicable(255)

prtExPh1MlTsSubChMask		1.3.6.1.4.1.164.3.2.3.2.2.2.1.14
The Sub-Channel Type Mask. This variable is relevant only when Time-Slot Type is SubCh (e.g. prtExPh1MlTsType = subCh1...subCh8).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtExPh1MlTsChRate		1.3.6.1.4.1.164.3.2.3.2.2.2.1.15
The Rate of the Signaling Channel. notApplicable(1) when TS Type is other than Signaling or Transparent
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), r16Kbps(2), r32Kbps(3), r64Kbps(4), r8Kbps(5), auto(6)

prtExPh1MlTsByteReversal		1.3.6.1.4.1.164.3.2.3.2.2.2.1.16
Byte Reversal. This variable defines whether the LSB or MSB is transmitted first. no(2) - MSB is transmitted first yes(3) - LSB is transmitted first.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), no(2), yes(3)

prtExPh1MlTsSigProfile		1.3.6.1.4.1.164.3.2.3.2.2.2.1.17
This object indicates the Signaling Profile of the port. It is applicable only when prtMl4SigProfile=perTS. p1 = profile 1 p2 = profile 2 p3 = profile 3 p4 = profile 4 p5 = profile 5
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), p1(3), p2(4), p3(5), p4(6), p5(7)

prtInPh1MlCnfgTable		1.3.6.1.4.1.164.3.2.3.2.2.3
The write operation into the Table Objects is valid only to the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtInPh1MlCnfgEntry

prtInPh1MlCnfgEntry		1.3.6.1.4.1.164.3.2.3.2.2.3.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtInPh1MlCnfgEntry

prtInPh1MlCnfgIdx		1.3.6.1.4.1.164.3.2.3.2.2.3.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtInPh1MlSltType		1.3.6.1.4.1.164.3.2.3.2.2.3.1.2
This attribute indicates a unique slot position where the card is inserted. For ISDN BRI port of MX300/30: io1(5) = isdn1(5) and io2(6) = isdn2(6) In the ?004 Unit the entries io6(10)..io12(16) are not valid
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

prtInPh1MlPrtIdx		1.3.6.1.4.1.164.3.2.3.2.2.3.1.3
This attribute indicates a unique port number. MPH.1/E1 and MPH.1/T1 cards have three internal interfaces. MX3000 modules may have up to 50 internal ports.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtInPh1MlConnect		1.3.6.1.4.1.164.3.2.3.2.2.3.1.4
This attribute indicates whether the port should be considered in any of the mux algorithms.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3)

prtInPh1MlRate		1.3.6.1.4.1.164.3.2.3.2.2.3.1.5
This attribute indicates the port speed.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	r1x56eq56Kbps(1), r1x64eq64Kbps(2), r2x56eq112Kbps(3), r2x64eq128Kbps(4), r3x56eq168Kbps(5), r3x64eq192Kbps(6), r4x56eq224Kbps(7), r4x64eq256Kbps(8), r5x56eq280Kbps(9), r5x64eq320Kbps(10), r6x56eq336Kbps(11), r6x64eq384Kbps(12), r7x56eq392Kbps(13), r7x64eq448Kbps(14), r8x56eq448Kbps(15), r8x64eq512Kbps(16), r9x56eq504Kbps(17), r9x64eq576Kbps(18), r10x56eq560Kbps(19), r10x64eq640Kbps(20), r11x56eq616Kbps(21), r11x64eq704Kbps(22), r12x56eq672Kbps(23), r12x64eq768Kbps(24), r13x56eq728Kbps(25), r13x64eq832Kbps(26), r14x56eq784Kbps(27), r14x64eq896Kbps(28), r15x56eq840Kbps(29), r15x64eq960Kbps(30), r16x56eq896Kbps(31), r16x64eq1024Kbps(32), r17x56eq952Kbps(33), r17x64eq1088Kbps(34), r18x56eq1008Kbps(35), r18x64eq1152Kbps(36), r19x56eq1064Kbps(37), r19x64eq1216Kbps(38), r20x56eq1120Kbps(39), r20x64eq1280Kbps(40), r21x56eq1176Kbps(41), r21x64eq1344Kbps(42), r22x56eq1232Kbps(43), r22x64eq1408Kbps(44), r23x56eq1288Kbps(45), r23x64eq1472Kbps(46), r24x56eq1344Kbps(47), r24x64eq1536Kbps(48), r25x56eq1400Kbps(49), r25x64eq1600Kbps(50), r26x56eq1456Kbps(51), r26x64eq1664Kbps(52), r27x56eq1512Kbps(53), r27x64eq1728Kbps(54), r28x56eq1568Kbps(55), r28x64eq1792Kbps(56), r29x56eq1624Kbps(57), r29x64eq1856Kbps(58), r30x56eq1680Kbps(59), r30x64eq1920Kbps(60), r31x56eq1736Kbps(61), r31x64eq1984Kbps(62), r32x56eq1792Kbps(63), r32x64eq2048Kbps(64), r1x1dot5eq1dot5M(65), r2x1dot5eq3M(66), r3x1dot5eq4dot5M(67), r4x1dot5eq6M(68), r5x1dot5eq7dot5M(69), r6x1dot5eq9M(70), r7x1dot5eq10dot5M(71), r8x1dot5eq12M(72), r1x2Meq2M(73), r2x2Meq4M(74), r3x2Meq6M(75), r4x2Meq8M(76), r5x2Meq10M(77), r6x2Meq12M(78), r7x2Meq14M(79), r8x2Meq16M(80), noRate(100)

prtInPh1MlProtocol		1.3.6.1.4.1.164.3.2.3.2.2.3.1.6
This attribute indicates the applied protocol.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	fr(1), frPlus(2), pCellRelay(3), hdlcSdlc(4), transparentHdlc(5), ciscoBridgedEth(6)

prtInPh1MlConnectionTyp		1.3.6.1.4.1.164.3.2.3.2.2.3.1.7
This attribute indicates the link connection type. It is required for three reasons: FR/CR Inband management operation (LMI,CLMM...). CIR check. NMS network management. SameNetManaged - indicates network internal line. SameNetNotMana - indicates network internal line, but the remote mux is not managed by the nms. User - User to Network Interface. OtherNet - Network To Network Interfce. PubNet - Access Mux To PubNet Interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	sameNetManaged(1), sameNetNotMana(2), user(3), otherNet(4), pubNet(5), notApplicable(255)

prtInPh1MlCongResponse		1.3.6.1.4.1.164.3.2.3.2.2.3.1.8
This attribute indicates how to handle the congestion indication to/from the mux internal connection side (for example transmit/receive becn to/from the network). no - do nothing FlowControl - translate the congestion indication between the port and the internal connection port according to the definition of the prtInPh1MlFlowControl parameters. The operation is done in both directions.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), flowControl(3)

prtInPh1MlCongLevel		1.3.6.1.4.1.164.3.2.3.2.2.3.1.9
This attribute indicates the level of delayed data in precents of the total available dynamic memory, for which the port will start to operate . The resolution of the parameter is 5 percent. Valid values: 10..70, 255. 255=notApplicable.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtInPh1MlTc		1.3.6.1.4.1.164.3.2.3.2.2.3.1.10
This attribute indicates the Tc parameter which is the time period of the sliding window in which the Bc/Be are tested. The value of this parameter is identical for all the ports in the specific card. 255=notApplicable.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	tc1sec(1), tc2sec(2), tc3sec(3), tc4sec(4), notApplicable(255)

prtInPh1MlFlowControl		1.3.6.1.4.1.164.3.2.3.2.2.3.1.11
This attribute indicates the required flow control betweeen the port and the remote equipment.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(2), fecnBecn(3)

prtInPh1MlSegment		1.3.6.1.4.1.164.3.2.3.2.2.3.1.12
This object is the Segmentation in Bytes. In protocol FR+, ISDN internals, MX 30/300 the segmentation is: 50 (2) ,158 (3) ,266 (4) ,376 (5), 484 (6) In MX 3000/4: For protocol FR+ (internal ISDN ports of MHS.S, MHS.U, MHS.E1, MHS.T1 cards) segmentation values are: 236 (7),472 (8), 708 (9), 944 (10) ,1180 (11)
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), s36Byte(2), s150Byte(3), s264Byte(4), s378Byte(5), s492Byte(6), s236Byte(7), s472Byte(8), s708Byte(9), s944Byte(10), s1180Byte(11)

prtInPh1MlFrMngProt		1.3.6.1.4.1.164.3.2.3.2.2.3.1.13
This object indicates the Frame-Relay management protocol. ansiT1 = ANSI T1.617 Annex D (this is the default value). This parameter is applicable only for FR and FR+ protocols. When prtInPh1MlConnectionTyp = sameNetManaged, this object will be RO (internally determined).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), none(2), lmi(3), ansiT1(4), annexA(5)

prtInPh1MlEnqPeriod		1.3.6.1.4.1.164.3.2.3.2.2.3.1.14
This object is the Status Enquiry Period, in seconds. It determines the frequency of the Status Enquiry message as sent by the FR user side. At the FR network side, it determines the timeout for this message reception. Default = 4 seconds. This parameter is applicable only for FR and FR+ protocols AND only when prtInPh1MlFrMngProt is NOT (notApplicable or none). 0=notApplicable.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..30

prtInPh1MlFullRptPeriod		1.3.6.1.4.1.164.3.2.3.2.2.3.1.15
This object is the Full Report Frequency. It determines the number of the Status Enquiry messages sent by the FR user side, before a Full Report Request is sent. The units are : Status Enquiry messages (periods). Valid values: 1 .. 255. 255 = infinite (never sent). This parameter is applicable only for FR and FR+ protocols AND only when prtInPh1MlFrMngProt is NOT (notApplicable or none). 0=notApplicable.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..255

prtInPh1MlFrWindowSize		1.3.6.1.4.1.164.3.2.3.2.2.3.1.16
This object is the FR Window Size. It determines the number of samplings in the sliding window that counts the errors. This parameter is applicable only for FR and FR+ protocols AND only when prtInPh1MlFrMngProt is NOT (notApplicable or none). 0=notApplicable.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..10

prtInPh1MlErrorsThreshold		1.3.6.1.4.1.164.3.2.3.2.2.3.1.17
This object is the Max Errors. It determines the number of Status Enquiry Errors that occured within the FR sliding window, before this port is considered DOWN (threshold). This parameter is applicable only for FR and FR+ protocols AND only when prtInPh1MlFrMngProt is NOT (notApplicable or none). 0=notApplicable.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..10

prtInPh1MlMaxIdleTime		1.3.6.1.4.1.164.3.2.3.2.2.3.1.18
Move to higher prioritized connected link after this period of seconds of silence on the current link. 0=Never. Never move to higher prioritized connected link. UNIT is seconds. Valid values are: 0, 1, 2, 3, 4, 5, 10, 20, 30, 40, 50, 60, 120, 180, 240, 300, 360, 420, 480, 540, 600, 900, 1200, 1500, 1800. Attempt to Set an invalid value will result in getting the default value.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..1800

prtInPh1MlBearerCh		1.3.6.1.4.1.164.3.2.3.2.2.3.1.19
Defines which B (bearer) channels are used for transferring ISDN data. Default value is: none (255). anyChannel (2) is skipped because it is not in use here.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), channelB1(3), channelB2(4), chB1andchB2(5), none(255)

prtInPh1MlAssociatedExCh		1.3.6.1.4.1.164.3.2.3.2.2.3.1.20
This object indicates the external port associated to this internal port. At present, it is used by the Hybrid (mp2100h), MHS-4 cards which can have up to 64 dynamic internal ports associated with External ports. For ISDN cards, the value will be: notApplicable (255). The associated external of an ISDN internal port is represented by the MIB object: prtIsdnDirectoryPrtNu.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), notApplicable(255)

prtInPh1MlClockEncoding		1.3.6.1.4.1.164.3.2.3.2.2.3.1.21
This object is the Encoding type of the Line. This parameter is applicable only for FR and FR+ protocols.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), nrz(2), nrzI(3), fm0(4), manchester(5), diffManchester(6)

prtInPh1MlMinSeparators		1.3.6.1.4.1.164.3.2.3.2.2.3.1.22
Minimum number of bytes separating between two adjacent frames (HDLC item). 0 = notApplicable
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..16

prtInPh1MlCcittCrc		1.3.6.1.4.1.164.3.2.3.2.2.3.1.23
This object indicates how many Bits are used for CRC (HDLC item).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), crc16(2), crc32(3)

prtInPh1MlFrameSeparator		1.3.6.1.4.1.164.3.2.3.2.2.3.1.24
This object indicates what should be transferred on the line when there are no frames to pass (HDLC item). idles: mean that FF will pass on the line flags: mean that 7E will pass on the line.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), idles(2), flags(3)

prtInPh1MlDlciTable		1.3.6.1.4.1.164.3.2.3.2.2.4
The write operation into the Table Objects is valid only to the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtInPh1MlDlciEntry

prtInPh1MlDlciEntry		1.3.6.1.4.1.164.3.2.3.2.2.4.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtInPh1MlDlciEntry

prtInPh1MlDlciCnfgIdx		1.3.6.1.4.1.164.3.2.3.2.2.4.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtInPh1MlDlciSltIdx		1.3.6.1.4.1.164.3.2.3.2.2.4.1.2
This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

prtInPh1MlDlciPrtIdx		1.3.6.1.4.1.164.3.2.3.2.2.4.1.3
This attribute indicates a unique internal port number. MPH.1/E1 and MPH.1/T1 cards have three internal ports.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	inPrt1(101), inPrt2(102), inPrt3(103)

prtInPh1MlDlciIdx		1.3.6.1.4.1.164.3.2.3.2.2.4.1.4
This attribute indicates a unique index for each possible used dlci(16..991). When the protocol is not Multiplexing protocol, then its type is 'user' and the only valid index is 1.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..991

prtInPh1MlDlciValid		1.3.6.1.4.1.164.3.2.3.2.2.4.1.5
This attribute indicates whether the attributes in this entry are valid or not. The user can add/delete pvc (dlci to dlci connection) by modifing this object
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3)

prtInPh1MlDlciIConSlt		1.3.6.1.4.1.164.3.2.3.2.2.4.1.6
This attribute indicates a unique slot position In the Mux (Agent) where the dlci is routed to. In the ?004 Unit the entries io6(10)..io16) are not valid
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noConnect(2), cl(3), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

prtInPh1MlDlciIConPrt		1.3.6.1.4.1.164.3.2.3.2.2.4.1.7
This attribute indicates a unique port id which the dlci is routed to.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), exPrt5(5), exPrt6(6), exPrt7(7), exPrt8(8), exPrt9(9), exPrt10(10), clNMS(99), noConnect(100), inPrt1(101), inPrt2(102), inPrt3(103), inPrt4(104), inPrt5(105), inPrt6(106), inPrt7(107), inPrt8(108), inPrt9(109), inPrt10(110), inPrt11(111), inPrt12(112)

prtInPh1MlDlciIConDlci		1.3.6.1.4.1.164.3.2.3.2.2.4.1.8
This attribute indicates a unique internal connection dlci number which the src dlci is routed to.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..991

prtInPh1MlDlciTxBc		1.3.6.1.4.1.164.3.2.3.2.2.4.1.9
This attribute indicates a unique Tx committed bandwidth on the user transmit line or at the port receive line.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	full(1), zero(2), txBc9600bps(3), txBc14200bps(4), txBc19200bps(5), txBc28800bps(6), txBc32000bps(7), txBc38400bps(8), txBc48000bps(9), txBc56000bps(10), txBc57600bps(11), txBc64Kbps(12), txBc128Kbps(13), txBc192Kbps(14), txBc256Kbps(15), txBc320Kbps(16), txBc384Kbps(17), txBc448Kbps(18), txBc512Kbps(19), txBc768Kbps(20), txBc1024Kbps(21)

prtInPh1MlDlciTxBe		1.3.6.1.4.1.164.3.2.3.2.2.4.1.10
This attribute indicates a unique Tx excess bandwidth on the user transmit line or at the port receive line.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	full(1), zero(2), txBe9600bps(3), txBe14200bps(4), txBe19200bps(5), txBe28800bps(6), txBe32000bps(7), txBe38400bps(8), txBe48000bps(9), txBe56000bps(10), txBe57600bps(11), txBe64Kbps(12), txBe128Kbps(13), txBe192Kbps(14), txBe256Kbps(15), txBe320Kbps(16), txBe384Kbps(17), txBe448Kbps(18), txBe512Kbps(19), txBe768Kbps(20), txBe1024Kbps(21)

prtInPh1MlDlciRxBc		1.3.6.1.4.1.164.3.2.3.2.2.4.1.11
This attribute indicates a unique Rx committed bandwidth on the user receive line or at the port transmit line.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	full(1), zero(2), rxBc9600bps(3), rxBc14200bps(4), rxBc19200bps(5), rxBc28800bps(6), rxBc32000bps(7), rxBc38400bps(8), rxBc48000bps(9), rxBc56000bps(10), rxBc57600bps(11), rxBc64Kbps(12), rxBc128Kbps(13), rxBc192Kbps(14), rxBc256Kbps(15), rxBc320Kbps(16), rxBc384Kbps(17), rxBc448Kbps(18), rxBc512Kbps(19), rxBc768Kbps(20), rxBc1024Kbps(21)

prtInPh1MlDlciRxBe		1.3.6.1.4.1.164.3.2.3.2.2.4.1.12
This attribute indicates a unique Rx excess bandwidth on the user receive line or at the port transmit line.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	full(1), zero(2), rxBe9600bps(3), rxBe14200bps(4), rxBe19200bps(5), rxBe28800bps(6), rxBe32000bps(7), rxBe38400bps(8), rxBe48000bps(9), rxBe56000bps(10), rxBe57600bps(11), rxBe64Kbps(12), rxBe128Kbps(13), rxBe192Kbps(14), rxBe256Kbps(15), rxBe320Kbps(16), rxBe384Kbps(17), rxBe448Kbps(18), rxBe512Kbps(19), rxBe768Kbps(20), rxBe1024Kbps(21)

prtInPh1MlDlciPriority		1.3.6.1.4.1.164.3.2.3.2.2.4.1.13
This attribute indicates a unique priority of the pcv. 1 is the lowest priority and 8 is the highest priority.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..8

prtInPh1MlDlciStatus		1.3.6.1.4.1.164.3.2.3.2.2.4.1.14
This attribute indicates the status of the pvc. The status is disconnected(1) when one of the sides is programmed as not connected
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	disconnected(1), connected(2)

prtPhMlCnfgTable		1.3.6.1.4.1.164.3.2.3.2.2.5
The write operation into the Table Objects is valid only to the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtPhMlCnfgEntry

prtPhMlCnfgEntry		1.3.6.1.4.1.164.3.2.3.2.2.5.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtPhMlCnfgEntry

prtPhMlCnfgIdx		1.3.6.1.4.1.164.3.2.3.2.2.5.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtPhMlSltIdx		1.3.6.1.4.1.164.3.2.3.2.2.5.1.2
This attribute indicates a unique slot position where the module is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid. For the Vmux2100 Main Board notApplicable (1) is used.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

prtPhMlPrtIdx		1.3.6.1.4.1.164.3.2.3.2.2.5.1.3
This attribute indicates a unique port number. ML-20 cards have just one external interface.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	exPrt1(1)

prtPhMlConnect		1.3.6.1.4.1.164.3.2.3.2.2.5.1.4
This attribute indicates whether the port should be considered in any of the mux algorithms.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3)

prtPhMlRate		1.3.6.1.4.1.164.3.2.3.2.2.5.1.5
This attribute indicates the configured port speed. auto - rate is adapted automatically to the attached modem rate.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	r1x64eq64Kbps(2), r2x64eq128Kbps(4), r3x64eq192Kbps(6), r4x64eq256Kbps(8), r5x64eq320Kbps(10), r6x64eq384Kbps(12), r7x64eq448Kbps(14), r8x64eq512Kbps(16), r9x64eq576Kbps(18), r10x64eq640Kbps(20), r11x64eq704Kbps(22), r12x64eq768Kbps(24), r13x64eq832Kbps(26), r14x64eq896Kbps(28), r15x64eq960Kbps(30), r16x64eq1024Kbps(32), r17x64eq1088Kbps(34), r18x64eq1152Kbps(36), r19x64eq1216Kbps(38), r20x64eq1280Kbps(40), r21x64eq1344Kbps(42), r22x64eq1408Kbps(44), r23x64eq1472Kbps(46), r24x64eq1536Kbps(48), r25x64eq1600Kbps(50), r26x64eq1664Kbps(52), r27x64eq1728Kbps(54), r28x64eq1792Kbps(56), r29x64eq1856Kbps(58), r30x64eq1920Kbps(60), r31x64eq1984Kbps(62), r32x64eq2048Kbps(64), auto(70)

prtPhMlCAS		1.3.6.1.4.1.164.3.2.3.2.2.5.1.6
This attribute indicates whether Channel Associated Signaling (CAS) is used.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3)

prtPhMlClockMode		1.3.6.1.4.1.164.3.2.3.2.2.5.1.7
Clock mode.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	dce(2), ext-dce(3), dte(4)

prtPhMlSatBuffer		1.3.6.1.4.1.164.3.2.3.2.2.5.1.8
Satellite Buffer (+/- 256).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), no(2), yes(3)

prtPhMlDialProcess		1.3.6.1.4.1.164.3.2.3.2.2.5.1.9
Dial Process.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), no(2), callIn(3), callOut(4)

prtPhMlSyncRestore		1.3.6.1.4.1.164.3.2.3.2.2.5.1.10
Sync Restoration time, in seconds. notApplicable=0.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..10

prtPhMlBus		1.3.6.1.4.1.164.3.2.3.2.2.5.1.11
The TDM BUS this port is linked to.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), busA(2), busB(3)

prtPhMlMfSyncSlot		1.3.6.1.4.1.164.3.2.3.2.2.5.1.12
This attribute indicates whether the sync is synchronized according to a certain card and the slot of this card. This operation is required in order to bypass signaling of PCM voice channels. In the ?004 Unit the entries io6(10)..io12(16) are not valid
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(2), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

prtPhMlClockSource		1.3.6.1.4.1.164.3.2.3.2.2.5.1.13
The Clock Source: TC (Tx Clock) or RC (Rx Clock) signals.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), txClock(2), rxClock(3)

prtPhMlErrCorrection		1.3.6.1.4.1.164.3.2.3.2.2.5.1.14
This object indicates if Error Correction mechanism should be applied or not. It will be applicable only if the interface HW includes the Error Correction chip.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), no(2), yes(3)

prtPhMlCorrectionMode		1.3.6.1.4.1.164.3.2.3.2.2.5.1.15
This object is applicable only when prtPhMlErrCorrection=yes. random - enables to correct up to 3 random errors in an 23 bit frame built from 12 data bits and 11 appended parity bits. bursty - interleaving 3 frames, allows correcting bursts of 9 bit length.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), random(2), bursty(3)

prtPhMlControlSignals		1.3.6.1.4.1.164.3.2.3.2.2.5.1.16
This object shows whether the Port will ignore or implement the control signals like DCD, CTS, DTR.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), ignore(2), implement(3)

prtPhMlInterfaceType		1.3.6.1.4.1.164.3.2.3.2.2.5.1.17
The SW Configurable Interface Type.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), v35(2), x21(3), rs232(4), rs449(5), ei530(6), ei530a(7)

prtPhMlClockPolarity		1.3.6.1.4.1.164.3.2.3.2.2.5.1.18
This object indicates the clock polarity.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), normal(2), inverted(3)

prtLogicalCnfgTable		1.3.6.1.4.1.164.3.2.3.2.17.1
The write operation into the Table Objects is valid only to the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtLogicalCnfgEntry

prtLogicalCnfgEntry		1.3.6.1.4.1.164.3.2.3.2.17.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtLogicalCnfgEntry

prtLogicalCnfgIdx		1.3.6.1.4.1.164.3.2.3.2.17.1.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtLogicalSltIdx		1.3.6.1.4.1.164.3.2.3.2.17.1.1.2
Slot Index. For ISDN BRI Ports of MX300/30, io1(5) = isdn1(5) and io2(6) = isdn2(6).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

prtLogicalPrtIdx		1.3.6.1.4.1.164.3.2.3.2.17.1.1.3
This attribute indicates a unique port number. This port number should be an internal port number: inPrt1(101)->inPrt50(150), linkSel1(200)->linkSel50(250), encaps1(300)-> encaps50(350), huntGr1(101) -> huntGr10(110).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtLogicalConnect		1.3.6.1.4.1.164.3.2.3.2.17.1.1.4
This attribute indicates whether the port should be considered in any of the mux algorithms.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	no(2), yes(3)

prtLogicalFunction		1.3.6.1.4.1.164.3.2.3.2.17.1.1.5
This parameter defines the function of the relevant channel.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notApplicable(1), linkSelector(2), encapsulator(3), huntGroup(4)

prtLogicalRowStatus		1.3.6.1.4.1.164.3.2.3.2.17.1.1.6
This parameter allows the NMS to create/delete logical ports. The only possible supported RowStatus vaules are active (1) and destroy (6).
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

linkSelectorCnfgTable		1.3.6.1.4.1.164.3.2.3.2.17.2
The write operation into the Table Objects is valid only to the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LinkSelectorCnfgEntry

linkSelectorCnfgEntry		1.3.6.1.4.1.164.3.2.3.2.17.2.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	LinkSelectorCnfgEntry

linkSelectorCnfgIdx		1.3.6.1.4.1.164.3.2.3.2.17.2.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

linkSelectorSltIdx		1.3.6.1.4.1.164.3.2.3.2.17.2.1.2
Slot Index
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

linkSelectorPrtIdx		1.3.6.1.4.1.164.3.2.3.2.17.2.1.3
This attribute indicates a unique port number. This port number should be internal port number: higher or equal to linkSeL1(201).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

linkSelectorMaxIdleTime		1.3.6.1.4.1.164.3.2.3.2.17.2.1.4
Move to higher prioritized connected link after this period of seconds of silence on the current link. 0=move immediately to higher prioritized connected link. UNIT is seconds.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..255

linkSelectorMode		1.3.6.1.4.1.164.3.2.3.2.17.2.1.5
If the link selector is in mode: backup(2)=then the link with the lower priority will be used in case of failure of the higher priority link, bod(3)=bandwidth on demand or dynamic bandwidth allocation means that links with lower priority will be used whenever additional bandwidth is required.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), backup(2), bod(3)

linkSelectorRevert		1.3.6.1.4.1.164.3.2.3.2.17.2.1.6
If the link selector is in mode backup: auto(2)=return automatically to Main link when it is OK. manual(3)=stays connected to backup link.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), auto(2), manual(3)

linkSelectorMinBUSession		1.3.6.1.4.1.164.3.2.3.2.17.2.1.7
Minimum duration of a backup session before returning to Main Link. Relevant in Backup Mode and when Revert is auto(2). Value 255 is for NEVER which means never return to Main Link. UNIT is minutes.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..255

linkSelectorPLinkTable		1.3.6.1.4.1.164.3.2.3.2.17.3
The write operation into the Table Objects is valid only to the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LinkSelectorPLinkEntry

linkSelectorPLinkEntry		1.3.6.1.4.1.164.3.2.3.2.17.3.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	LinkSelectorPLinkEntry

pLinkCnfgIdx		1.3.6.1.4.1.164.3.2.3.2.17.3.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

pLinkSltIdx		1.3.6.1.4.1.164.3.2.3.2.17.3.1.2
Slot Index
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

pLinkPrtIdx		1.3.6.1.4.1.164.3.2.3.2.17.3.1.3
This attribute indicates a unique port number. This port number should be the link selector number.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	200..250

pLinkIdx		1.3.6.1.4.1.164.3.2.3.2.17.3.1.4
This index is the row number.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..8

pLinkSlotNu		1.3.6.1.4.1.164.3.2.3.2.17.3.1.5
The slot of the prioritized link. For ISDN BRI ports of MX300/30, io1(5) = isdn1(5) and io2(6) = isdn2(6).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noConnect(2), cl(3), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

pLinkPortNu		1.3.6.1.4.1.164.3.2.3.2.17.3.1.6
The port of the prioritized link. Value 100 is for noConnect.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

pLinkPrioNu		1.3.6.1.4.1.164.3.2.3.2.17.3.1.7
The priority of the prioritized link. MIN=1...., MAX=8.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..8

pLinkVRate		1.3.6.1.4.1.164.3.2.3.2.17.3.1.8
The rate to use with this link.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	r1x56eq56Kbps(1), r1x64eq64Kbps(2), r2x56eq112Kbps(3), r2x64eq128Kbps(4), r3x56eq168Kbps(5), r3x64eq192Kbps(6), r4x56eq224Kbps(7), r4x64eq256Kbps(8), r5x56eq280Kbps(9), r5x64eq320Kbps(10), r6x56eq336Kbps(11), r6x64eq384Kbps(12), r7x56eq392Kbps(13), r7x64eq448Kbps(14), r8x56eq448Kbps(15), r8x64eq512Kbps(16), r9x56eq504Kbps(17), r9x64eq576Kbps(18), r10x56eq560Kbps(19), r10x64eq640Kbps(20), r11x56eq616Kbps(21), r11x64eq704Kbps(22), r12x56eq672Kbps(23), r12x64eq768Kbps(24), r13x56eq728Kbps(25), r13x64eq832Kbps(26), r14x56eq784Kbps(27), r14x64eq896Kbps(28), r15x56eq840Kbps(29), r15x64eq960Kbps(30), r16x56eq896Kbps(31), r16x64eq1024Kbps(32), r17x56eq952Kbps(33), r17x64eq1088Kbps(34), r18x56eq1008Kbps(35), r18x64eq1152Kbps(36), r19x56eq1064Kbps(37), r19x64eq1216Kbps(38), r20x56eq1120Kbps(39), r20x64eq1280Kbps(40), r21x56eq1176Kbps(41), r21x64eq1344Kbps(42), r22x56eq1232Kbps(43), r22x64eq1408Kbps(44), r23x56eq1288Kbps(45), r23x64eq1472Kbps(46), r24x56eq1344Kbps(47), r24x64eq1536Kbps(48), r25x56eq1400Kbps(49), r25x64eq1600Kbps(50), r26x56eq1456Kbps(51), r26x64eq1664Kbps(52), r27x56eq1512Kbps(53), r27x64eq1728Kbps(54), r28x56eq1568Kbps(55), r28x64eq1792Kbps(56), r29x56eq1624Kbps(57), r29x64eq1856Kbps(58), r30x56eq1680Kbps(59), r30x64eq1920Kbps(60), r31x56eq1736Kbps(61), r31x64eq1984Kbps(62), noRate(100)

prtExPhPlCnfgTable		1.3.6.1.4.1.164.3.2.3.2.3.1
The write operation into the Table Objects is valid only to the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtExPhPlCnfgEntry

prtExPhPlCnfgEntry		1.3.6.1.4.1.164.3.2.3.2.3.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtExPhPlCnfgEntry

prtExPhPlCnfgIdx		1.3.6.1.4.1.164.3.2.3.2.3.1.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtExPhPlSltIdx		1.3.6.1.4.1.164.3.2.3.2.3.1.1.2
This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

prtExPhPlPrtIdx		1.3.6.1.4.1.164.3.2.3.2.3.1.1.3
This attribute indicates a unique port number. In case of PH.1 card, only exPrt(1) is valid.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), exPrt5(5), exPrt6(6)

prtExPhPlConnect		1.3.6.1.4.1.164.3.2.3.2.3.1.1.4
This attribute indicates whether the port should be considered in any of the mux algorithms.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3)

prtExPhPlHRate		1.3.6.1.4.1.164.3.2.3.2.3.1.1.5
This attribute indicates the port speed for HIGH speed cards. The card has limitations about the maximum sigma channel speeds and about the possible rates for each clock mode . N - The rate is valid for DCE and EXT-DCE Nodal clock mode. L - The rate is valid for DCE and EXT-DCE Local clock mode. E - The rate is valid for DTE External clock mode. 'r9d6KbpsNLE' means rate of 9.6 Kbps ('d'=dot). Note: Some rate attributes have been changed. As the MIB was already released with the old attributes, the names of the options were not changed. The new names + attributes are in a comment. Example: r2048KbpsE (63), -- r2048KbpsNLE
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), r32KbpsNLE(2), r48KbpsNLE(3), r56KbpsNLE(4), r64KbpsNLE(5), r112KbpsNLE(6), r128KbpsNLE(7), r168KbpsNLE(8), r192KbpsNLE(9), r224KbpsNLE(10), r256KbpsNLE(11), r280KbpsE(12), r320KbpsE(13), r336KbpsNLE(14), r384KbpsNLE(15), r392KbpsE(16), r448KbpsNLE(17), r504KbpsLE(18), r512KbpsE(19), r560KbpsE(20), r576KbpsLE(21), r616KbpsE(22), r640KbpsE(23), r672KbpsNLE(24), r704KbpsE(25), r728KbpsE(26), r768KbpsNLE(27), r784KbpsE(28), r832KbpsE(29), r840KbpsE(30), r896KbpsNLE(31), r952KbpsE(32), r960KbpsE(33), r1008KbpsLE(34), r1024KbpsE(35), r1064KbpsE(36), r1088KbpsE(37), r1120KbpsE(38), r1152KbpsLE(39), r1176KbpsE(40), r1216KbpsE(41), r1232KbpsE(42), r1280KbpsE(43), r1288KbpsE(44), r1344KbpsNLE(45), r1400KbpsE(46), r1408KbpsE(47), r1456KbpsE(48), r1472KbpsE(49), r1512KbpsE(50), r1536KbpsE(51), r1568KbpsE(52), r1600KbpsE(53), r1624KbpsE(54), r1664KbpsE(55), r1680KbpsE(56), r1728KbpsE(57), r1736KbpsE(58), r1792KbpsNLE(59), r1856KbpsE(60), r1920KbpsE(61), r1984KbpsE(62), r2048KbpsE(63), r9d6KbpsNLE(65), r14d4KbpsNLE(66), r16KbpsNLE(67), r19d2KbpsNLE(68), r28d8KbpsNLE(69), r38d4KbpsNLE(70), r57d6KbpsNLE(71), r115d2KbpsNLE(72), r24000bps(73)

prtExPhPlLRate		1.3.6.1.4.1.164.3.2.3.2.3.1.1.6
This attribute indicates the port speed for LOW speed cards. The card has limitations about the possible rates for each clock mode. N - The rate is valid for DCE and EXT-DCE Nodal clock mode. L - The rate is valid for DCE and EXT-DCE Local clock mode. E - The rate is valid for DTE External clock mode. Note: Some rate attributes have been changed. As the MIB was already released with the old attributes, the names of the options were not changed. The new names + attributes are in a comment. Example: r57600bpsLE (16), -- r57600bpsNLE
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), r300bpsNLE(2), r600bpsNLE(3), r800bpsNLE(4), r1200bpsNLE(5), r2400bpsNLE(6), r4800bpsNLE(7), r9600bpsNLE(8), r14400bpsLE(9), r19200bpsNLE(10), r28800bpsLE(11), r32000bpsNLE(12), r38400bpsNLE(13), r48000bpsNLE(14), r56000bpsNLE(15), r57600bpsLE(16), r64000bpsNLE(17), r112000bps(18), r115200bps(19), r16000bpsNLE(20), r100bpsNLE(21), r128000bps(22), r24000bps(23)

prtExPhPlProtocol		1.3.6.1.4.1.164.3.2.3.2.3.1.1.7
This object indicates the applied protocol.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	fr(1), frPlus(2), pCellRelay(3), hdlcSdlc(4), transparentHdlc(5), async(6), asyncReliable(7), activePPP(8), slip(9), pppAgent(10), slipAgent(11), transparent(12), sna(13), ft1Dot2(14)

prtExPhPlConnectionTyp		1.3.6.1.4.1.164.3.2.3.2.3.1.1.8
This attribute indicates the link connection type. It is required for three reasons: FR/CR Inband management opration (LMI,CLMM...). CIR check. NMS network management. SameNetManaged - indicates network internal line. SameNetMotMana - indicates network internal line, but the remote mux is not managed by the NMS. User - User to Network Interface. OtherNet - Network To Network Interface. PubNet - Access Mux To PubNet Interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	sameNetManaged(1), sameNetNotMana(2), user(3), otherNet(4), pubNet(5), notApplicable(255)

prtExPhPlClkMode		1.3.6.1.4.1.164.3.2.3.2.3.1.1.9
Clock mode.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	dce(1), extDce(2), dte(3), int(4), lbt(5)

prtExPhPlDceClkSrc		1.3.6.1.4.1.164.3.2.3.2.3.1.1.10
This attribute indicates the source of the clock when working in dce or ext-dce clock mode. notApplicable(1) - is applied for dte(3) and lbt(5) clock modes. When clock mode is dte, the clock source is always external, therefore this object's value is notApplicable. local(2) and nodalTiming(3) - are valid in dce(1), extDce(2) or int(4) clock modes. The recommended clock source is local(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), local(2), nodalTiming(3)

prtExPhPlCongResponse		1.3.6.1.4.1.164.3.2.3.2.3.1.1.11
This attribute indicates how to handle the congestion indication to/from the mux internal connection side (for example transmit/received becn to/from the network). no - do nothing flowControl - translates the congestion indication between the port and the internal connection port according to the definition of the prtInPh1MlFlowControl parameters. The operation is done on both directions. toFlowControl- translates the backward congestion indication received from the internal connection port (normally the network side) to flow control and do nothing in the other direction.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), flowControl(3), toFlowControl(4)

prtExPhPlCongLevel		1.3.6.1.4.1.164.3.2.3.2.3.1.1.12
This attribute indicates the level of delayed data in precents of total available dynamic memory, for which the port will start to operate as congested. The resolution of the parameter is 5 percent.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..70

prtExPhPlTc		1.3.6.1.4.1.164.3.2.3.2.3.1.1.13
This attribute indicates the Tc parameter which is the time period of the sliding window in which the Bc/Be are tested. The value of this parameter is identical for all the ports of a specific card .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	tc1sec(1), tc2sec(2), tc3sec(3), tc4sec(4), notApplicable(255)

prtExPhPlFlowControl		1.3.6.1.4.1.164.3.2.3.2.3.1.1.14
This attribute indicates the required flow control betweeen the port and the remote equipment. fecnBecn - is valid only for FR, FR+ and CR protocols. xonXoff,dtrCts - are valid only for Async protocols. speedReduction - is valid only for DLC protocol when the Clock Mode is DCE and the Clock Source is Local.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(2), fecnBecn(3), xonXoff(4), dtrCts(5), speedReduction(6)

prtExPhPlDcdRts		1.3.6.1.4.1.164.3.2.3.2.3.1.1.15
Protocol may require end to end connect indication over the network. End to end link connection establishment over the FR network will be indicated to the user by using DCD or RTS control signals, depending on the clock mode: DCE or DTE respectively. The options are : - On : DCD(DCE)/RTS(DTE) will be constantly ON no matter if the End to End connection is established or not. - End to End: The DCD(DCE)/RTS(DTE) will be according to the status of the End to End connection.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), on(2), endToEnd(3)

prtExPhPlDcdRtsControlPath		1.3.6.1.4.1.164.3.2.3.2.3.1.1.16
Protocol may require end to end connect indication over the network. This parameter defines whether to take the user connection status (RTS(DCE)/DCD(DTE)) and forward it to the network side. - on : Transmit active connection to the network regardless the RTS/DCD control lines status. - off: Transmit active connection to the network according to the status of the RTS/DCD pin.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), off(2), on(3)

prtExPhPlDataBits		1.3.6.1.4.1.164.3.2.3.2.3.1.1.17
This attribute indicates the number of data bits in async frame. It is relevant only for Async protocols.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), dataBits7Bits(2), dataBits8Bits(3)

prtExPhPlParity		1.3.6.1.4.1.164.3.2.3.2.3.1.1.18
This attribute indicates the parity operation mode in async frame. It is relevant only for Async protocols.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), odd(2), even(3), none(4)

prtExPhPlStopBits		1.3.6.1.4.1.164.3.2.3.2.3.1.1.19
This attribute indicates the minimum number of stop bits in the tx async frame. It is relevant only for Async protocols.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), sb1Bit(2), sb1dot5Bits(3), sb2Bits(4)

prtExPhPlLXon		1.3.6.1.4.1.164.3.2.3.2.3.1.1.20
This attribute indicates the character used as X-On to notify receive enable. This parameter is valid only for async protocols. Valid values: 0..255. The value 256 indicates that it's not applicable
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtExPhPlLXoff		1.3.6.1.4.1.164.3.2.3.2.3.1.1.21
This attribute indicates the character used as X-Off to notify receive disable. This parameter is valid only for async protocols. Valid values: 0..255. The value 256 indicates that it's not applicable
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtExPhPlFrMngProt		1.3.6.1.4.1.164.3.2.3.2.3.1.1.22
This object indicates the Frame-Relay management protocol. ansiT1 = ANSI T1.617 Annex D (this is the default value). This parameter is applicable only for FR and FR+ protocols. When prtExPhPlConnectionTyp = sameNetManaged, this object will be RO (internally determined).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), none(2), lmi(3), ansiT1(4), annexA(5)

prtExPhPlEnqPeriod		1.3.6.1.4.1.164.3.2.3.2.3.1.1.23
This object is the Status Enquiry Period, in seconds. It determines the frequency of the Status Enquiry message as sent by the FR user side. At the FR network side, it determines the timeout for this message reception. Default = 4 seconds. This parameter is applicable only for FR and FR+ protocols AND only when prtExPhPlFrMngProt is NOT (notApplicable or none).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..30

prtExPhPlFullRptPeriod		1.3.6.1.4.1.164.3.2.3.2.3.1.1.24
This object is the Full Report Frequency. It determines the number of the Status Enquiry messages sent by the FR user side, before a Full Report Request is sent. The units are : Status Enquiry messages (periods). Valid values: 1 .. 255. 255 = infinite. This parameter is applicable only for FR and FR+ protocols AND only when prtExPhPlFrMngProt is NOT (notApplicable or none).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..255

prtExPhPlFrWindowSize		1.3.6.1.4.1.164.3.2.3.2.3.1.1.25
This object is the FR Window Size. It determines the number of samplings in the sliding window that counts the errors. This parameter is applicable only for FR and FR+ protocols AND only when prtExPhPlFrMngProt is NOT (notApplicable or none).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..10

prtExPhPlErrorsThreshold		1.3.6.1.4.1.164.3.2.3.2.3.1.1.26
This object is the Max Errors. It determines the number of Status Enquiry Errors that occured within the FR sliding window, before this port is considered DOWN (threshold). This parameter is applicable only for FR and FR+ protocols AND only when prtExPhPlFrMngProt is NOT (notApplicable or none).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..10

prtExPhPlPvcCreateMsg		1.3.6.1.4.1.164.3.2.3.2.3.1.1.27
This object is Update Message (if required or not). It determines whether a message of a New PVC Creation is requested or not (yes/no). Default = no. This parameter is applicable only for FR and FR+ protocols AND only when prtExPhPlFrMngProt is NOT (notApplicable or none).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), no(2), yes(3)

prtExPhPlCllmMsg		1.3.6.1.4.1.164.3.2.3.2.3.1.1.28
This object is CLLM Message (if required or not). It determines whether to send (or not) a congestion message when the port is Rx congested. Default = no. This parameter is applicable only for FR and FR+ protocols AND only when prtExPhPlFrMngProt is NOT (notApplicable or none).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), no(2), yes(3)

prtExPhPlProtDelayLevel		1.3.6.1.4.1.164.3.2.3.2.3.1.1.29
This object is the Segmentation in Bytes. In some cases, the enumerated values will mean other segmentation values than specified: Product: MX-3000 MX-3000 MX-300/MX-30 Protocol: FR+ Transparent FR+ ----------------------------------------------------- level 1 50 Bytes 44 Bytes 50 Bytes level 2 158 Bytes 155 Bytes 158 Bytes level 3 266 Bytes 266 Bytes 266 Bytes level 4 376 Bytes 377 Bytes 376 Bytes level 5 484 Bytes 488 Bytes 484 Bytes Defval=level 1 value This parameter is applicable only for FR+ and transparent protocols.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), s36Byte(2), s150Byte(3), s264Byte(4), s378Byte(5), s492Byte(6)

prtExPhPlClockEncoding		1.3.6.1.4.1.164.3.2.3.2.3.1.1.30
This object is the Encoding type of the Line. This parameter is applicable only for FR and FR+ protocols. For MAXCESS 3000 & MP2100H: when setting to nrzI (3) the nrzI works as nrzI Mark. For MAXCESS 30/300 when setting to nrzI (3) the nrzI works as nrzI Space.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), nrz(2), nrzI(3), fm0(4), manchester(5), diffManchester(6), nrzISpace(7), nrzIMark(8)

prtExPhPlMinSeparators		1.3.6.1.4.1.164.3.2.3.2.3.1.1.31
Minimum number of bytes separating between two adjacent frames (HDLC item). 0 = notApplicable
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..16

prtExPhPlCcittCrc		1.3.6.1.4.1.164.3.2.3.2.3.1.1.32
This object indicates how many Bits are used for CRC (HDLC item).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), crc16(2), crc32(3)

prtExPhPlFrameSeparator		1.3.6.1.4.1.164.3.2.3.2.3.1.1.33
This object indicates what should be transferred on the line when there are no frames to pass (HDLC item). idles: mean that FF will pass on the line flags: mean that 7E will pass on the line.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), idles(2), flags(3)

prtExPhPlIdleCode		1.3.6.1.4.1.164.3.2.3.2.3.1.1.34
Determines the code for transmission when there are no frames to transmit on the line. The value should be 0 to FFH.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtExPhPlJitter		1.3.6.1.4.1.164.3.2.3.2.3.1.1.35
Maximum variant delay of the FR network, in msec.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..1000

prtExPhPlDlciTable		1.3.6.1.4.1.164.3.2.3.2.3.2
The write operation into the Table Objects is valid only at the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtExPhPlDlciEntry

prtExPhPlDlciEntry		1.3.6.1.4.1.164.3.2.3.2.3.2.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtExPhPlDlciEntry

prtExPhPlDlciCnfgIdx		1.3.6.1.4.1.164.3.2.3.2.3.2.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtExPhPlDlciSltIdx		1.3.6.1.4.1.164.3.2.3.2.3.2.1.2
This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

prtExPhPlDlciPrtIdx		1.3.6.1.4.1.164.3.2.3.2.3.2.1.3
This attribute indicates a unique internal port number. PH.1/E1 and PH.1/T1 cards have three internal ports. Stand-alone units may have six such ports.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), exPrt5(5), exPrt6(6)

prtExPhPlDlciIdx		1.3.6.1.4.1.164.3.2.3.2.3.2.1.4
This attribute indicates a unique index for each possible used dlci(16..991). When the protocol is not Multiplexing protocol, its type is 'user' and the only valid index is 1.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..991

prtExPhPlDlciValid		1.3.6.1.4.1.164.3.2.3.2.3.2.1.5
This attribute indicates whether the attributes in this entry are valid or not. The user can add/delete pvc (dlci to dlci connection) by modifing this object
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3)

prtExPhPlDlciIConSlt		1.3.6.1.4.1.164.3.2.3.2.3.2.1.6
This attribute indicates a unique slot position In the Mux (Agent) where the dlci is routed to. cl - will represent any of the CL slots. This value can be selected for multiple DLCIs of the product. In the ?004 Unit the entries io6(10)..io16) are not valid
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noConnect(2), cl(3), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

prtExPhPlDlciIConPrt		1.3.6.1.4.1.164.3.2.3.2.3.2.1.7
This attribute indicates a unique port id which the dlci is routed to. clNMS - will be used for NMS SNMP messages. It can be any port of the CL card. This value will be selectable only if prtExPhPlDlciIConSlt='cl' or 'notApplicable'.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), exPrt5(5), exPrt6(6), exPrt7(7), exPrt8(8), exPrt9(9), exPrt10(10), clNMS(99), noConnect(100), inPrt1(101), inPrt2(102), inPrt3(103), inPrt4(104), inPrt5(105), inPrt6(106), inPrt7(107), inPrt8(108), inPrt9(109), inPrt10(110)

prtExPhPlDlciIConDlci		1.3.6.1.4.1.164.3.2.3.2.3.2.1.8
This attribute indicates a unique internal connection dlci number, the dlci is routed to.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..991

prtExPhPlDlciTxBc		1.3.6.1.4.1.164.3.2.3.2.3.2.1.9
This attribute indicates a unique Tx committed bandwidth on the user transmit line (or at the port receive line).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	full(1), zero(2), txBc9600bps(3), txBc14400bps(4), txBc19200bps(5), txBc28800bps(6), txBc32000bps(7), txBc38400bps(8), txBc48000bps(9), txBc56000bps(10), txBc57600bps(11), txBc64Kbps(12), txBc128Kbps(13), txBc192Kbps(14), txBc256Kbps(15), txBc320Kbps(16), txBc384Kbps(17), txBc448Kbps(18), txBc512Kbps(19), txBc768Kbps(20), txBc1024Kbps(21), txBc16000bps(25), txBc112Kbps(26)

prtExPhPlDlciTxBe		1.3.6.1.4.1.164.3.2.3.2.3.2.1.10
This attribute indicates a unique Tx excess bandwidth on the user transmit line (or at the port receive line).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	full(1), zero(2), txBe9600bps(3), txBe14400bps(4), txBe19200bps(5), txBe28800bps(6), txBe32000bps(7), txBe38400bps(8), txBe48000bps(9), txBe56000bps(10), txBe57600bps(11), txBe64Kbps(12), txBe128Kbps(13), txBe192Kbps(14), txBe256Kbps(15), txBe320Kbps(16), txBe384Kbps(17), txBe448Kbps(18), txBe512Kbps(19), txBe768Kbps(20), txBe1024Kbps(21), txBc16000bps(25), txBc112Kbps(26)

prtExPhPlDlciRxBc		1.3.6.1.4.1.164.3.2.3.2.3.2.1.11
This attribute indicates a unique Rx committed bandwidth on the user receive line (or at the port transmit line).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	full(1), zero(2), rxBc9600bps(3), rxBc14400bps(4), rxBc19200bps(5), rxBc28800bps(6), rxBc32000bps(7), rxBc38400bps(8), rxBc48000bps(9), rxBc56000bps(10), rxBc57600bps(11), rxBc64Kbps(12), rxBc128Kbps(13), rxBc192Kbps(14), rxBc256Kbps(15), rxBc320Kbps(16), rxBc384Kbps(17), rxBc448Kbps(18), rxBc512Kbps(19), rxBc768Kbps(20), rxBc1024Kbps(21), rxBc16000bps(25), rxBc112Kbps(26)

prtExPhPlDlciRxBe		1.3.6.1.4.1.164.3.2.3.2.3.2.1.12
This attribute indicates a unique Rx excess bandwidth on the user receive line (or at the port transmit line).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	full(1), zero(2), rxBe9600bps(3), rxBe14400bps(4), rxBe19200bps(5), rxBe28800bps(6), rxBe32000bps(7), rxBe38400bps(8), rxBe48000bps(9), rxBe56000bps(10), rxBe57600bps(11), rxBe64Kbps(12), rxBe128Kbps(13), rxBe192Kbps(14), rxBe256Kbps(15), rxBe320Kbps(16), rxBe384Kbps(17), rxBe448Kbps(18), rxBe512Kbps(19), rxBe768Kbps(20), rxBe1024Kbps(21), rxBc16000bps(25), rxBc112Kbps(26)

prtExPhPlDlciPriority		1.3.6.1.4.1.164.3.2.3.2.3.2.1.13
This attribute indicates a unique priority of the pcv. 1 is the lowest priority and 8 is the highest priority.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..8

prtExPhPlDlciStatus		1.3.6.1.4.1.164.3.2.3.2.3.2.1.14
This attribute indicates the status of the pvc. The status is disconnected(1) when one of the sides is programmed as not connected
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	disconnected(1), connected(2)

prtExPhPlModemTable		1.3.6.1.4.1.164.3.2.3.2.3.3
External Modem Parameters. The write operation into the Table Objects is valid only for the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtExPhPlModemEntry

prtExPhPlModemEntry		1.3.6.1.4.1.164.3.2.3.2.3.3.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtExPhPlModemEntry

prtExPhPlModemCnfgIdx		1.3.6.1.4.1.164.3.2.3.2.3.3.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtExPhPlModemSltIdx		1.3.6.1.4.1.164.3.2.3.2.3.3.1.2
This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

prtExPhPlModemPrtIdx		1.3.6.1.4.1.164.3.2.3.2.3.3.1.3
This attribute indicates a unique port number. In case of PH.1 card, only exPrt(1) is valid.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), exPrt5(5), exPrt6(6)

prtExPhPlModemStatus		1.3.6.1.4.1.164.3.2.3.2.3.3.1.4
This object indicates whether a Dial Up Modem is enabled on this port. Default: disable For Vmux devices this object shows whether there is Modem Relay support.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(2), enable(3), relay(4)

prtExPhPlModemActivate		1.3.6.1.4.1.164.3.2.3.2.3.3.1.5
This object indicates whether the Dial Up Modem is activated when the first frame is received or it is always activated. Default: onFirstFrame
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	onFirstFrame(2), always(3), notApplicable(255)

prtExPhPlModemMaxIdleTime		1.3.6.1.4.1.164.3.2.3.2.3.3.1.6
Max Time allowed in Seconds without any traffic before the line is disconnected. Legal Values are: 1 sec, 2 sec .. 5 sec, 10 sec, 20 sec.. 1 min, 2 min .. 10 min, 15 min, 20 min, 25 min, 30 min. 65535 sec. means that this parameter is not applicable. Default: 1 sec.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtExPhPlModemTimeBtwnCalls		1.3.6.1.4.1.164.3.2.3.2.3.3.1.7
Minimum Time in Seconds which is required after a call was disconnected. In this time no other call will be initiated from this Modem port even if there were frames transmitted to this port. This time is required for some Modems which have initializations that take a few seconds. Legal Values are: 0 sec. - 30 sec., 1-5 min. 65535 sec. means that this parameter is not applicable. Default: 0 sec
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtExPhPlModemCallDelay		1.3.6.1.4.1.164.3.2.3.2.3.3.1.8
Time in Seconds that the device will wait before dialing to the remote device. This feature is mostly used when there is a backup modem to the main link and the main link is down. In this case it is important to prevent the 2 devices from dialing through the backup modems to each other at the same time. It is advised to configure one side with a small call delay and the other side with a large call delay. Legal Values are: 0 - 30, 60, 120, 180, 240, 300, 600, 900, 1200, 1500, 1800 . 65535 sec. means that this parameter is not applicable. Default: 0 sec
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtExLs2CnfgTable		1.3.6.1.4.1.164.3.2.3.2.4.1
The write operation into the Table Objects is valid only to the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtExLs2CnfgEntry

prtExLs2CnfgEntry		1.3.6.1.4.1.164.3.2.3.2.4.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtExLs2CnfgEntry

prtExLs2CnfgIdx		1.3.6.1.4.1.164.3.2.3.2.4.1.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtExLs2SltIdx		1.3.6.1.4.1.164.3.2.3.2.4.1.1.2
This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

prtExLs2PrtIdx		1.3.6.1.4.1.164.3.2.3.2.4.1.1.3
This attribute indicates a unique port index. For the Ls2/X.58 exPrt(7)..exPrt(10) are not valid.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), exPrt5(5), exPrt6(6), exPrt7(7), exPrt8(8), exPrt9(9), exPrt10(10)

prtExLs2Connect		1.3.6.1.4.1.164.3.2.3.2.4.1.1.4
This attribute indicates whether the port should be considered in any of the mux algorithms.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3)

prtExLs2Rate		1.3.6.1.4.1.164.3.2.3.2.4.1.1.5
Port rates.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	r2400bps(2), r4800bps(3), r9600bps(4), r19200bps(5)

prtExLs2ClkMode		1.3.6.1.4.1.164.3.2.3.2.4.1.1.6
This attribute indicates a unique port operation clock mode.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	dce(1), ext-dce(2), dte(3)

prtExLs2Cts		1.3.6.1.4.1.164.3.2.3.2.4.1.1.7
CTS.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	on(2), rts-min(3), rts-max(4)

prtExLs2Dcd		1.3.6.1.4.1.164.3.2.3.2.4.1.1.8
DCD.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	on(2), card-sync(3)

prtExLs2EnvIdx		1.3.6.1.4.1.164.3.2.3.2.4.1.1.9
Envelope Index. When prtInLs2EnvAssign=auto, the value is 0 (not applicable).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..24

prtInLs2CnfgTable		1.3.6.1.4.1.164.3.2.3.2.4.2
The write operation into the Table Objects is valid only to the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtInLs2CnfgEntry

prtInLs2CnfgEntry		1.3.6.1.4.1.164.3.2.3.2.4.2.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtInLs2CnfgEntry

prtInLs2CnfgIdx		1.3.6.1.4.1.164.3.2.3.2.4.2.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtInLs2SltIdx		1.3.6.1.4.1.164.3.2.3.2.4.2.1.2
This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

prtInLs2PrtIdx		1.3.6.1.4.1.164.3.2.3.2.4.2.1.3
This attribute indicates a unique internal port index.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	inPrt1(101), inPrt2(102)

prtInLs2Connect		1.3.6.1.4.1.164.3.2.3.2.4.2.1.4
This attribute indicates whether the port should be considered in any of the mux algorithms. It also affects all the module considerations because the module has only one Internal interface which is the composite channel.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3)

prtInLs2Group		1.3.6.1.4.1.164.3.2.3.2.4.2.1.5
This attribute indicates the group number of the port. LS-2 internal ports with the same group number share the same Time slot of the main link
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..12

prtInLs2Member		1.3.6.1.4.1.164.3.2.3.2.4.2.1.6
This attribute indicates the group member id of the port. This parameter is for the automatic envelope assignment algorithm.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..4

prtInLs2LinkTo		1.3.6.1.4.1.164.3.2.3.2.4.2.1.7
It indicates the slot of the main link card to which the LS2 card is mapped. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

prtInLs2EnvAssign		1.3.6.1.4.1.164.3.2.3.2.4.2.1.8
Envelope assignment type.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	auto(2), manual(3)

prtVc2CnfgTable		1.3.6.1.4.1.164.3.2.3.2.5
- For products supporting more than one configuration, the write operation into the Table is valid only to the TmpCnfg entry. - For products that do not support configurations, the write operation into the Table will be to prtVc2CnfgIdx=1.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtVc2CnfgEntry

prtVc2CnfgEntry		1.3.6.1.4.1.164.3.2.3.2.5.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtVc2CnfgEntry

prtVc2CnfgIdx		1.3.6.1.4.1.164.3.2.3.2.5.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtVc2SltIdx		1.3.6.1.4.1.164.3.2.3.2.5.1.2
This attribute indicates a unique slot position where the card is inserted. For Stand Alone products like WR: notApplicable (255)
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

prtVc2PrtIdx		1.3.6.1.4.1.164.3.2.3.2.5.1.3
A unique identifier of the port, within the card. For MP-2100/2200 card ports, Web Ranger and FCD-IP Voice ports the values will be: exPrt1 (1) exPrt2 (2) exPrt3 (3) exPrt4 (4) exPrt5 (5) exPrt6 (6) exPrt7 (7) exPrt8 (8) exPrt9 (9) exPrt10 (10) exPrt11 (11) exPrt12 (12) exPrt13 (13) exPrt14 (14) exPrt15 (15) exPrt16 (16) For LA-240: The index for fixed voice ports will be - exPrt6 (6) exPrt7 (7) exPrt8 (8) exPrt9 (9) The index for voice card ports will be - Slot number * 100 + ch (for IO-1: 101..104, for IO-2: 201..204). For other products' index see their specification.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtExVc2Connect		1.3.6.1.4.1.164.3.2.3.2.5.1.4
This attribute indicates whether the port should be considered in any of the mux algorithms.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3), v51(4), v52(5)

prtExVc2TransGain		1.3.6.1.4.1.164.3.2.3.2.5.1.5
Transmit gain in dBm. For ports of MP-104/204, MP-2100/2200 VC-6A, VC-6AG, VC-8 VC-4/Omni and VC-16 cards, the units will be 0.1dBm because valid values can be in 0.5dBm steps.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtExVc2ReceiveGain		1.3.6.1.4.1.164.3.2.3.2.5.1.6
Receive gain in dBm. For ports of MP-104/204, MP-2100/2200 VC-6A, VC-6AG, VC-8 VC-4/Omni and VC-16 cards, the units will be 0.1dBm because valid values can be in 0.5dBm steps.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtExVc2Wire		1.3.6.1.4.1.164.3.2.3.2.5.1.7
For some cards, this object is equal for all the ports in the specific card because of HW limitations. For FXO & FXS this parameter is not applicable.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	w2wire(1), w4wire(2), notApplicable(255)

prtExVc2CodingLaw		1.3.6.1.4.1.164.3.2.3.2.5.1.8
This attribute indicates the Method/Law for decoding/encoding the voice information. aLaw(1) is the standard Law for E1 links. uLaw(2) is the standard Law for T1 links. This object is equal for all the ports in the specific module because of HW limitations
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	aLAW(1), uLAW(2)

prtExVc2Sig		1.3.6.1.4.1.164.3.2.3.2.5.1.9
This attribute indicates the method for decoding/encoding the signaling information(on/off hook). noSignaling (1) - not using signaling (only voice). robbedBitMultiFrame(2) - is the standard method for T1 links and proprietary method for E1 links. chAssociatedE1 (3) - is valid only for E1 G.732S links. robbedBitFrame (4) - is proprietary method implimenting 7 bit for the voice and 1 bit dedicated for signaling. For some cards, this object is equal for all the ports in the specific module because of HW limitations.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noSignaling(1), robbedBitMultiFrame(2), chAssociatedE1(3), robbedBitFrame(4)

prtExVc2Oos		1.3.6.1.4.1.164.3.2.3.2.5.1.10
This object is equal for all the ports in the specific card because of HW limitations
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	forcedIdle(1), forcedBusy(2), busyIdle(3), idleBusy(4), notApplicable(5)

prtExVc2LinkTo		1.3.6.1.4.1.164.3.2.3.2.5.1.11
This attribute indicates the slot of the ML card to which the VC card is mapped. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

prtExVc2OperMode		1.3.6.1.4.1.164.3.2.3.2.5.1.12
This object indicates the operation mode of the port. normal = bi-directional (Tx/Rx) unidirectRx = unidirectional Rx. broadcast = Tx upon request.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	normal(2), unidirectRx(3), broadcast(4)

prtExVc2SigProfile		1.3.6.1.4.1.164.3.2.3.2.5.1.13
This object indicates the Signaling Profile of the port. notApplicable - for VC-2 family and when prtExVc2Sig=noSignaling(1) p1 = profile 1 p2 = profile 2 p3 = profile 3 p4 = profile 4
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), manual(2), p1(3), p2(4), p3Fxo3S3(5), reversePolarity(6), meteringPulse(7), p4(8)

prtExVc2CallEnable		1.3.6.1.4.1.164.3.2.3.2.5.1.14
This object indicates the Enabled Call direction. notApplicable - for all cards except VC-2/R2. both - incoming + outgoing.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), incoming(2), outgoing(3), both(4)

prtExVc2R2Delay		1.3.6.1.4.1.164.3.2.3.2.5.1.15
This object indicates the R2 Delay. notApplicable - for all cards except VC-2/R2.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), terrestrial(2), satellite(3)

prtExVc2CasStd		1.3.6.1.4.1.164.3.2.3.2.5.1.16
This object indicates the CAS (Channel Associated Signaling) Standard. notApplicable - for all cards except VC-2/R2.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), r2Q422(2), specialA(3), specialB(4), specialC(5), specialD(6), specialE(7), specialF(8), specialG(9)

prtExVc2EchoCanceler		1.3.6.1.4.1.164.3.2.3.2.5.1.17
Echo canceler activation. notApplicable - for VC-2 and VC-6 cards.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), off(2), on(3)

prtExVc2IfType		1.3.6.1.4.1.164.3.2.3.2.5.1.18
Interface Type.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), w2Em(2), w4Em(3), fxo(4), fxs(5)

prtExVc2Encoding		1.3.6.1.4.1.164.3.2.3.2.5.1.19
Voice Encoding Mode. linear - is relevant only for the ports of VC-16A card.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), pcm(2), adpcm(3), linear(4)

prtExVc2TxBitCode		1.3.6.1.4.1.164.3.2.3.2.5.1.20
- - - For MP & FCD - - - This object represents 4 parameters, by 2 Octets : Tx D Bit Code-MSB nibble, Tx C Bit Code- nibble, Tx B Bit Code- nibble, Tx A Bit Code-LSB nibble. Each nibble: 0 hex = 0000 = Not Applicable 1 hex = 0001 = M lead 2 hex = 0010 = M lead inverse 3 hex = 0011 = Reverse Polarity 4 hex = 0100 = Metering Pulse 5 hex = 0101 = Forced 1 6 hex = 0110 = Forced 0 7-F hex - not used (invalid values) This object will be RO if prtExVc2SigProfile is NOT manual. - - - For WR II - - - This object represents the following 4 parameters by 2 Octets: 1. On/Off hook signaling transmission mode from the FXS towards the T1/E1 (MSB nibble 1). 2. Default signaling bits that are not in use (nibble 2). 3. Ring Detection signaling transmission mode from the FXO towards the T1/E1(nibble 3). 4. M (Mouth) Signaling transmission mode from the E&M towards the T1/E1(LSB nibble 4). Each nibble: --------------------------------------------------------------------------------------- Value On/Off Hook Default sig. Ring Detect. M (Mouth) --------------------------------------------------------------------------------------- 0 hex = 0000 Not Applicable Not Applicable. Not Applicable Not Applicable 1 hex = 0001 Tx A bit Values 1-3 are Tx A bit Tx A bit 2 hex = 0010 Tx A bit inverse for On/Off Hook Tx A bit inv. Tx A bit inv. 3 hex = 0011 Tx B bit A,B,A Inv,B Inv. Tx B bit Tx B bit 4 hex = 0100 Tx B bit inverse Values 4-7 are Tx B bit inv. Tx B bit inv. 5 hex = 0101 not Used-invalid for On/Off Hook not Used-invalid not Used-invalid 6 hex = 0110 not Used-invalid A, A Inverse. not Used-invalid not Used-invalid 7 hex = 0111 not Used-invalid not Used-invalid not Used-invalid 8 hex = 1000 not Used-invalid Values 8-11 are not Used-invalid not Used-invalid 9 hex = 1001 not Used-invalid for On/Off Hook not Used-invalid not Used-invalid A hex = 1010 not used-invalid B, B Inverse. not Used-invalid not Used-invalid B hex = 1011 not used-invalid The Bits order: not Used-invalid not Used-invalid C-F hex not used-invalid ABCD not Used-invalid not Used-invalid Default value: 11 11
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

prtExVc2RxBitOutput		1.3.6.1.4.1.164.3.2.3.2.5.1.21
- - - For MP (VC-Q card only) & FCD - - - This object represents 3 parameters by 2 Octets: Spare -MSB nibble, always=0 hex E Lead Output - nibble, Reverse Polarity Output- nibble, Metering Pulse Output -LSB nibble. Each nibble: 0 hex = 0000 = Not Applicable 1 hex = 0001 = Rx A bit 2 hex = 0010 = Rx A bit inverse 3 hex = 0011 = Rx B bit 4 hex = 0100 = Rx B bit inverse 5 hex = 0101 = Rx C bit 6 hex = 0110 = Rx C bit inverse 7 hex = 0111 = Rx D bit 8 hex = 1000 = Rx D bit inverse 9 hex = 1001 = none A-F hex - not used (invalid values) This object will be RO if prtExVc2SigProfile is NOT manual. - - - For MP (VC-8, VC-16, VC-16A cards) - - - This object represents 4 parameters, by 2 Octets : Tx D Bit Code-MSB nibble, Tx C Bit Code- nibble, Tx B Bit Code- nibble, Tx A Bit Code-LSB nibble. Each nibble: 0 hex = 0000 = Not Applicable 1 hex = 0001 = not used (invalid value) 2 hex = 0010 = not used (invalid value) 3 hex = 0011 = not used (invalid value) 4 hex = 0100 = not used (invalid value) 5 hex = 0101 = Forced 1 6 hex = 0110 = Forced 0 7-F hex - not used (invalid values) This object will be RO. - - - For WR II - - - This object represents the following 2 parameters in 1 Octet: 1. On/Off hook signaling receive mode from the T1/E1 into the FXS/FXO (MSB nibble 1). 2. E (Ear) Signaling receive mode from the T1/E1 into the E&M (LSB nibble 2). Each nibble: --------------------------------------------------------------------------------------- Value On/Off Hook E (Ear) --------------------------------------------------------------------------------------- 0 hex = 0000 Not Applicable Not Applicable 1 hex = 0001 Rx A bit Rx A bit 2 hex = 0010 Rx A bit inverse Rx A bit inverse 3 hex = 0011 Rx B bit Rx B bit 4 hex = 0100 Rx B bit inverse Rx B bit inverse 5-F hex not used-invalid not Used-invalid Default value: 11
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

prtExVc2MeterRate		1.3.6.1.4.1.164.3.2.3.2.5.1.22
This entry is applicable only for VC-6A/FXO, VC-6A/FXS, VC-8/FXO, VC-8/FXS, VC-16/FXO and VC-16/FXS. Meter Rate means rate of Call Meter in Public Phones, in KHz units. For some cards, the value must be the same for all card's ports.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), r16Khz(2), r12Khz(3), disabled(4)

prtExVc2IfSignaling		1.3.6.1.4.1.164.3.2.3.2.5.1.23
This entry is applicable only for VC-6A, VC-6AG, VC-8/FXO, VC-8/FXS, VC-16/FXO and VC-16/FXS cards. Interface Analog Signaling. Must be the same for all card's ports. loopStart - for the usual trunk/phone types. groundStart - for trunks that need Ground signaling . winkStart - for trunks that need Reverse Polarity.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), loopStart(2), groundStart(3), winkStart(4)

prtExVc2SeizeAck		1.3.6.1.4.1.164.3.2.3.2.5.1.24
This parameter shows whether the device will acknowledge a seize signal (On/Off Hook). When the value is set to yes(3) & the device receives an on/off hook signal it will transmit back an on/off hook signal. When the value is set to no(2) & the device receives an on/off hook signal it will NOT transmit back an on/off hook signal. Default value for WR FXO: no(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), no(2), yes(3)

prtExVc2EandMType		1.3.6.1.4.1.164.3.2.3.2.5.1.25
This is the signaling type on the E&M analog side. The analog signaling includes voltage, no. of pins and other parameters.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), type1(2), type2(3), type3(4), type5(5)

prtExVc2RemType		1.3.6.1.4.1.164.3.2.3.2.5.1.26
Remote Type. Applicable for VC-6A/4LB card & for IPMUX-1E Far End Type - E1,T1(T1-ESF) or T1-D4 .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), lb(2), pbx(3), e1(4), t1(5), t1D4(6)

prtExVc2ConvTime		1.3.6.1.4.1.164.3.2.3.2.5.1.27
Conversation Time in minutes. Applicable for VC-6A/4LB card.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), m2(2), m3(3), m5(4), unlimited(5)

prtExVc2SigFeedback		1.3.6.1.4.1.164.3.2.3.2.5.1.28
Signaling Feedback. Applicable for VC-8/FXO and VC-16/FXO cards.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), no(2), yes(3)

prtExVc2EchoCancelerModule		1.3.6.1.4.1.164.3.2.3.2.5.1.29
This parameter indicates whether Echo canceler module exists for this port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), notExist(2), exist(3)

prtExVc2ReversePolarity		1.3.6.1.4.1.164.3.2.3.2.5.1.30
This object Enables/Disables Reverse Polarity for this port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), disabled(2), enabled(3)

prtExVc2RingerFrequency		1.3.6.1.4.1.164.3.2.3.2.5.1.31
This object selects the Ringer Frequency (Hz) for this port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), f20Hz(2), f25Hz(3), f50Hz(4)

prtExVc2SigService		1.3.6.1.4.1.164.3.2.3.2.5.1.32
Signaling Service. advanced - is relevant only for ports of VC-8, VC-16 FXS cards. It is used for Signaling Services of V5.1 or R2.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), normal(2), advanced(3)

prtExVc2CallerIdEnable		1.3.6.1.4.1.164.3.2.3.2.5.1.33
This object Enables/Disables Receiving the Caller Id number from the remote side, for this port/channel.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), disabled(2), enabled(3)

prtExVc2CompressMethod		1.3.6.1.4.1.164.3.2.3.2.5.1.34
This object is applicable only when prtExVc2Encoding=adpcm. It defines which method is used for Compression. g726 - for 4 bits (the standard method). g726 - for 3 bits. It is especially needed for T1 applications with signaling.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), g726(2), g727(3)

prtExVc2ObMode		1.3.6.1.4.1.164.3.2.3.2.5.1.35
This object defines the Net operation mode of the Omni-Bus card's port. pointToPoint - only 2 end-point ports talk; like any other voice card omniBus - many talk and listen. Like conference call. All can listen to all. pointToMultiPointSrc - There is one Master who can be heard by all. All can talk, but only the Master can hear all. Others can hear only the Master. This port is of the Master (Src). pointToMultiPointDst - There is one Master who can be heard by all. All can talk, but only the Master can hear all. Others can hear only the Master. This port is of a Destination (NOT Master).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	pointToPoint(1), omniBus(2), pointToMultiPointSrc(3), pointToMultiPointDst(4)

prtExVc2VAD		1.3.6.1.4.1.164.3.2.3.2.5.1.36
This object defines whether Voice Activation Detector (VAD) will be On or Off. off - will be usually selected when a Modem is connected to the port; not a phone. notApplicable - when prtExVc2DspMode=pointToPoint.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), off(2), on(3)

prtExVc2NoiseLevelForVAD		1.3.6.1.4.1.164.3.2.3.2.5.1.37
This object defines the Level of Noise on the line, the Voice Activation Detector (VAD) will have to deal with. notApplicable - when prtExVc2VAD=off.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), low(2), medium(3), high(4)

prtExVc2WesternSigMode		1.3.6.1.4.1.164.3.2.3.2.5.1.38
This object defines the Western Signaling Mode. detector - detects signal and passes it as is. generator - generates the signal. notApplicable - when Western HW is not installed.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), detector(2), generator(3)

prtExVc2BusProtectionPoint		1.3.6.1.4.1.164.3.2.3.2.5.1.39
This object defines if the port is Bus Protection Point or not. notApplicable - when prtExVc2DspMode=pointToPoint. When we have a chain of devices where the edge devices ports are the Bus Protection Point, user must configure one of these ports as 'first' and the other as 'last'. It does not matter which one, it just matters that they will be different.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), no(2), first(3), last(4)

prtExVc2ImpedanceStandard		1.3.6.1.4.1.164.3.2.3.2.5.1.40
This object defines the Standard used for Impedance. -G.712 - 600 Ohm - used in USA and other countries. -Q552/ETSI - used in some countries in Europe -Q522/Italy - used in Italy.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	g712(1), q552ETSI(2), q522Italy(3)

prtHsfCnfgTable		1.3.6.1.4.1.164.3.2.3.2.6
The write operation into the Table Objects is valid only to the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtHsfCnfgEntry

prtHsfCnfgEntry		1.3.6.1.4.1.164.3.2.3.2.6.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtHsfCnfgEntry

prtHsfCnfgIdx		1.3.6.1.4.1.164.3.2.3.2.6.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relate to the TmpCnfg.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtHsfSltIdx		1.3.6.1.4.1.164.3.2.3.2.6.1.2
This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

prtHsfPrtIdx		1.3.6.1.4.1.164.3.2.3.2.6.1.3
This attribute indicates a unique external port index. Hs2 has only two ports (exPrt1,exPrt2). Hs3 has three ports (exPrt1,exPrt2,exPrt3). Hsq and hsqN has four ports. Hs6 has six external ports. Hs12 has twelve external ports. inPrt1, inPrt2 - are relevant for VID card.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), exPrt5(5), exPrt6(6), exPrt7(7), exPrt8(8), exPrt9(9), exPrt10(10), exPrt11(11), exPrt12(12), inPrt1(101), inPrt2(102)

prtExHsfConnect		1.3.6.1.4.1.164.3.2.3.2.6.1.4
This attribute indicates whether the port should be considered in any of the mux algorithms.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3)

prtExHsfRate		1.3.6.1.4.1.164.3.2.3.2.6.1.5
This attribute indicates the port speed.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	r1x56eq56Kbps(1), r1x64eq64Kbps(2), r2x56eq112Kbps(3), r2x64eq128Kbps(4), r3x56eq168Kbps(5), r3x64eq192Kbps(6), r4x56eq224Kbps(7), r4x64eq256Kbps(8), r5x56eq280Kbps(9), r5x64eq320Kbps(10), r6x56eq336Kbps(11), r6x64eq384Kbps(12), r7x56eq392Kbps(13), r7x64eq448Kbps(14), r8x56eq448Kbps(15), r8x64eq512Kbps(16), r9x56eq504Kbps(17), r9x64eq576Kbps(18), r10x56eq560Kbps(19), r10x64eq640Kbps(20), r11x56eq616Kbps(21), r11x64eq704Kbps(22), r12x56eq672Kbps(23), r12x64eq768Kbps(24), r13x56eq728Kbps(25), r13x64eq832Kbps(26), r14x56eq784Kbps(27), r14x64eq896Kbps(28), r15x56eq840Kbps(29), r15x64eq960Kbps(30), r16x56eq896Kbps(31), r16x64eq1024Kbps(32), r17x56eq952Kbps(33), r17x64eq1088Kbps(34), r18x56eq1008Kbps(35), r18x64eq1152Kbps(36), r19x56eq1064Kbps(37), r19x64eq1216Kbps(38), r20x56eq1120Kbps(39), r20x64eq1280Kbps(40), r21x56eq1176Kbps(41), r21x64eq1344Kbps(42), r22x56eq1232Kbps(43), r22x64eq1408Kbps(44), r23x56eq1288Kbps(45), r23x64eq1472Kbps(46), r24x56eq1344Kbps(47), r24x64eq1536Kbps(48), r25x56eq1400Kbps(49), r25x64eq1600Kbps(50), r26x56eq1456Kbps(51), r26x64eq1664Kbps(52), r27x56eq1512Kbps(53), r27x64eq1728Kbps(54), r28x56eq1568Kbps(55), r28x64eq1792Kbps(56), r29x56eq1624Kbps(57), r29x64eq1856Kbps(58), r30x56eq1680Kbps(59), r30x64eq1920Kbps(60), r31x56eq1736Kbps(61), r31x64eq1984Kbps(62), r32Kbps(63)

prtExHsfClkMode		1.3.6.1.4.1.164.3.2.3.2.6.1.6
This attribute indicates a unique port operation clock mode.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	dce(1), ext-dce(2), dte(3), none(4)

prtExHsfCts		1.3.6.1.4.1.164.3.2.3.2.6.1.7
This attribute indicates a unique CTS control line operation mode.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), on(2), rts(3)

prtExHsfFifoSize		1.3.6.1.4.1.164.3.2.3.2.6.1.8
Size in bits.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	auto(2), s16bits(3), s30bits(4), s52bits(5), s72bits(6)

prtExHsfLinkTo		1.3.6.1.4.1.164.3.2.3.2.6.1.9
This attribute indicates a slot of Main Link module, that the port is linked to. This object is the same for all the ports in the specific card because of HW limitations. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

prtExHsfOperMode		1.3.6.1.4.1.164.3.2.3.2.6.1.10
This object indicates the operation mode of the port. normal = bi-directional (Tx/Rx) unidirectRx = unidirectional Rx. broadcast = Tx upon request. bidirBcastRing = Bidirectional Broadcast Ring. When this value is selected, AND RTS=On, the port opens its transmission channel.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	normal(2), unidirectRx(3), broadcast(4), bidirBcastRing(5)

prtExHsfInbandLoopback		1.3.6.1.4.1.164.3.2.3.2.6.1.11
This object indicates if Inband Loopback from the Network should be enabled or disabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), disabled(2), ft1Enabled(3)

prtExHsfClkPolarity		1.3.6.1.4.1.164.3.2.3.2.6.1.12
This object indicates the clock polarity. For FCD-M this object will be applicable only for the fixed HS port (the fixed port on the device).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), normal(2), invert(3)

prtExHsfControlSignal		1.3.6.1.4.1.164.3.2.3.2.6.1.13
This object indicates the Control Signal according to G.797 ITU-T standard. For FCD-M this object will be applicable for the fixed HS port (the fixed port on the device) and HS-Q/N channels. Local and End to End are applicable only when channel Interface type is RS-530, else it will be Not Applicable.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), local(2), endToEnd(3)

prtExHsfBcastRingSrcPort		1.3.6.1.4.1.164.3.2.3.2.6.1.14
This object is applicable only when prtExHsfOperMode= bidirBcastRing. In this case, the values mean: - none - this port will be connected to ML in TSA as usual. - exPrt1.. exPrtX ; X=maximum ports of the card in focus : it means that the same TS that is assigned in TSA to this port is actually connected also to this port, for Broadcast Ring mode. Therefore, this port should NOT be connected to ML in TSA.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), exPrt5(5), exPrt6(6), exPrt7(7), exPrt8(8), exPrt9(9), exPrt10(10), exPrt11(11), exPrt12(12), none(100), notApplicable(255)

prtExHs4CnfgTable		1.3.6.1.4.1.164.3.2.3.2.7.1
The write operation into the Table Objects is valid only to the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtExHs4CnfgEntry

prtExHs4CnfgEntry		1.3.6.1.4.1.164.3.2.3.2.7.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtExHs4CnfgEntry

prtExHs4CnfgIdx		1.3.6.1.4.1.164.3.2.3.2.7.1.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtExHs4SltIdx		1.3.6.1.4.1.164.3.2.3.2.7.1.1.2
This attribute indicates a unique slot position where the card is inserted.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

prtExHs4PrtIdx		1.3.6.1.4.1.164.3.2.3.2.7.1.1.3
A unique identifier of the port, within the card.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	exPrt1(1)

prtExHs4Connect		1.3.6.1.4.1.164.3.2.3.2.7.1.1.4
This attribute indicates whether the port should be considered in any of the mux algorithm. It also affects all the module considerations because the card has only one external (physical) interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3)

prtExHs4LineType		1.3.6.1.4.1.164.3.2.3.2.7.1.1.5
This attribute is the line type parameter for T1/E1 interface. The user should select only the parameters relevant to the specific card: T1 line code parameters for the HS-4/1 and E1 line code parameters for the HS-4/2. This parameter has the same values as dsx1LineType in T1/E1 MIB (RFC-1406). The parameters in dsx1LineType are: other (1) dsx1ESF (2) dsx1D4 (3) dsx1E1 (4) dsx1E1-CRC (5) dsx1E1-MF (6) dsx1E1-MF-CRC (7)
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	esfT1(2), sfT1(3), g732nE1(4), g732nE1CRC(5), g732sE1(6), g732sE1CRC(7)

prtExHs4LineCode		1.3.6.1.4.1.164.3.2.3.2.7.1.1.6
This attribute is the line code parameter used for T1/E1 interface. The user should select only the parameters relevant to the specific card: T1 line code parameters for the MPH.1/T1 and E1 line code parameters for the MPH.1/E1. This parameter has the same values as dsx1LineCoding in T1/E1 MIB (RFC-1406). The parameters in dsx1LineCoding are: dsx1JBZS (1) dsx1B8ZS (2) dsx1HDB3 (3) dsx1ZBTSI (4) dsx1AMI (5) other (6)
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	b7T1(1), b8zsT1(2), hdb3E1(4)

prtExHs4LineLen		1.3.6.1.4.1.164.3.2.3.2.7.1.1.7
This attribute is the line length parameter used only for T1 interfaces. len399p533ft=len-399-533ft
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unknown(1), len0p133ft(2), len134p266ft(3), len267p399ft(4), len400p533ft(5), len534p655ft(6), fcc68(7)

prtExHs4RestoreT		1.3.6.1.4.1.164.3.2.3.2.7.1.1.8
Time passing from the disappearance of the loss of synchronization condition (red alarm), to the restoration of normal service.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	restoreT1secFast(2), restoreT10sec62411(3), ccittE1(4)

prtExHs4OosSig		1.3.6.1.4.1.164.3.2.3.2.7.1.1.9
Out of Service signal type.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notsupported(2), forcedIdle(3), forcedBusy(4), busyIdle(5), idleBusy(6)

prtExHs4OosCode		1.3.6.1.4.1.164.3.2.3.2.7.1.1.10
OOS Code
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notsupported(2), oosCode00H(3), oosCode1aH(4), oosCode54H(5), oosCode7eH(6), oosCode7fH(7), oosCode98H(8), oosCode9eH(9), oosCoded5H(10), oosCodee4H(11), oosCodeffH(12)

prtExHs4IdleCode		1.3.6.1.4.1.164.3.2.3.2.7.1.1.11
Type value(00 - FF HEX), excluding 0H,8H,10H,12H,21H,24H, 42H,49H,84H,92H
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtExHs4MfClkSrcSlt		1.3.6.1.4.1.164.3.2.3.2.7.1.1.12
This attribute indicates whether the port Tx is multiframe synchronized with Rx multiframe of another port and the slot position of that port. This opration is required in order to bypass signaling of PCM voice channels. When its value is Local(2) there is no meaning to 'prtExHs4MfClkSrcPrt' parameter. In the ?004 Unit the entries io6(10)..io16) are not valid
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	local(2), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

prtExHs4MfClkSrcPrt		1.3.6.1.4.1.164.3.2.3.2.7.1.1.13
A unique number to identify a port position in the mux if the MultiFrame clock source is valid (YES). inPrt1 - for MTML-H/E1 cards.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	exPrt1(1), exPrt2(2), inPrt1(101)

prtExHs4TsCnfgTable		1.3.6.1.4.1.164.3.2.3.2.7.2
The write operation into the Table Objects is valid only to the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtExHs4TsEntry

prtExHs4TsEntry		1.3.6.1.4.1.164.3.2.3.2.7.2.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtExHs4TsEntry

prtExHs4TsCnfgIdx		1.3.6.1.4.1.164.3.2.3.2.7.2.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtExHs4TsSltIdx		1.3.6.1.4.1.164.3.2.3.2.7.2.1.2
This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

prtExHs4TsPrtIdx		1.3.6.1.4.1.164.3.2.3.2.7.2.1.3
This attribute indicates a unique port number. Hs4/T1 and Hs4/T1 cards have only one external interface.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	exPrt1(1)

prtExHs4TsIdx		1.3.6.1.4.1.164.3.2.3.2.7.2.1.4
This attribute indicates a unique time slot position. The valid time slots are: 1..24 for T1 Card and 1..31 for E1 interface. In G732S-E1 lines, time slot 16 is not valid for data, it is dedicated to multiframe synchronization bits and voice signaling.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtExHs4TsIConSlot		1.3.6.1.4.1.164.3.2.3.2.7.2.1.5
This attribute indicates whether the specified time slot is connected/routed internally in the Agent and to which card it is connected. In the ?004 Unit the entries io6(10)..io16) are not valid. split - will be used when the Src TS is connected to more than one slot OR more than one port (each needing less than a whole TS).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noConnect(2), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), split(100)

prtExHs4TsIConPrt		1.3.6.1.4.1.164.3.2.3.2.7.2.1.6
This attribute indicates the internally (In Mux) connected/routed port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), exPrt5(5), exPrt6(6), exPrt7(7), exPrt8(8), exPrt9(9), exPrt10(10), exPrt11(11), exPrt12(12), noConnect(100)

prtExHs4TsIConTs		1.3.6.1.4.1.164.3.2.3.2.7.2.1.7
This attribute indicates a unique time slot position. The valid time slots are: 1..24 for T1 Module and 1..31 for E1 interface. In G732S-E1 lines time slot 16 is not valid for data, it is dedicated for multiframe synchronization bits and voice signaling.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtExHsiCnfgTable		1.3.6.1.4.1.164.3.2.3.2.8.1
The write operation into the Table Objects is valid only to the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtExHsiCnfgEntry

prtExHsiCnfgEntry		1.3.6.1.4.1.164.3.2.3.2.8.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtExHsiCnfgEntry

prtExHsiCnfgIdx		1.3.6.1.4.1.164.3.2.3.2.8.1.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtExHsiSltIdx		1.3.6.1.4.1.164.3.2.3.2.8.1.1.2
This attribute indicates a unique slot position where the card is inserted.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), notApplicable(255)

prtExHsiPrtIdx		1.3.6.1.4.1.164.3.2.3.2.8.1.1.3
A unique port identifier within the card. For MP : 1..12 For DXC: 111 .. 2531. See DXC R6 spec for port index convention. For FCD-A, 'S' Interface external ports: 131, 141, 151, 161.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtExHsiConnect		1.3.6.1.4.1.164.3.2.3.2.8.1.1.4
This attribute indicates whether the port should be considered in any of the mux algorithms. v51 - this port is connected to a V5.1 interface. All rest of the values will be 'notApplicable' in this case. V5 MIB will be used instead. v52 - this port is connected to a V5.2 interface. All rest of the values will be 'notApplicable' in this case. V5 MIB will be used instead.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3), v51(4), v52(5)

prtExHsiRate		1.3.6.1.4.1.164.3.2.3.2.8.1.1.5
This attribute indicates the port speed.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	r600bps(2), r1200bps(3), r2400bps(4), r4800bps(5), r9600bps(6), r19200bps(7), r38400bps(8), r48kbps(9), r56kbps(10), r64kbps(11), r128kbps(12), notApplicable(255)

prtExHsiLinkTo		1.3.6.1.4.1.164.3.2.3.2.8.1.1.6
It indicates the slot of the main link card to which the HS-? card is mapped. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

prtExHsiInterface		1.3.6.1.4.1.164.3.2.3.2.8.1.1.7
It indicates the interface type: lt = line termination nt = network termination te = terminal equipment. lt1 - for ASMi-31 connection (not ISDN) For MP: For HS-U/I only 'lt' and 'nt' are applicable. For HS-U/1 only 'lt' is applicable. For HS-S , only 'te' and 'nt' are applicable. For HS-U, this object is not applicable. For HS-U6, HS-U12, are applicable: 'lt'=lt-i,'nt'=nt-i, lt1. For DXC: For HS-U8, HS-U16, are applicable: 'lt'=LT-I,'nt'=NT-I, 'lt1'=LT-1.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	lt(1), nt(2), te(3), lt1(4), notApplicable(255)

prtExHsiActType		1.3.6.1.4.1.164.3.2.3.2.8.1.1.8
It indicates the Activation Type. Activation Type is the Synchronization type towards the PBX. It is applicable only when prtExHsiInterface=nt. notApplicable - for cards that do not support this object, or when prtExHsiInterface is NOT nt.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), type1(2), type2(3), type3(4)

prtInHsiCnfgTable		1.3.6.1.4.1.164.3.2.3.2.8.2
The write operation into the Table Objects is valid only to the TmpCnfg entry. This table is not applicable for MP-2100 HS-U card type.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtInHsiCnfgEntry

prtInHsiCnfgEntry		1.3.6.1.4.1.164.3.2.3.2.8.2.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtInHsiCnfgEntry

prtInHsiCnfgIdx		1.3.6.1.4.1.164.3.2.3.2.8.2.1.1
This object indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtInHsiSltIdx		1.3.6.1.4.1.164.3.2.3.2.8.2.1.2
This object indicates a unique slot position where the card is inserted.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), notApplicable(255)

prtInHsiPrtIdx		1.3.6.1.4.1.164.3.2.3.2.8.2.1.3
A unique port identifier within the card. Valid values for MP: inPrt1 (101) .. inPrt48 (148). Valid values for DXC: 11012.. 25316. See DXC R6 spec for port index convention.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtInHsiConnect		1.3.6.1.4.1.164.3.2.3.2.8.2.1.4
This attribute indicates whether the port should be considered in any of the mux algorithms.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3)

prtInHsiRate		1.3.6.1.4.1.164.3.2.3.2.8.2.1.5
This object indicates the port speed. For HS-U/I and HS-S ports: 2 bit - up to 9600bps 4 bit - 19200bps 8 bit - 38400bps .. 64kbps. concentrated - this D channel goes to a Concentration channel, that represents many channels that this value was selected for them. The Concentrated channel is an Internal D Channel of the same card. This value is applicable only for D channels, except Concentration channel itself. --for HS-S and HS-U/I cards the Concentration channel will always be: internal-13 --for MP-2200 HS-S12, HS-S6, HS-U12, HS-U6 and DXC HS-U8 and HS-U16 cards, the Concentration channel is selected via the prtInHsiConcentratedTo object. notConnected - same as prtInHsiConnect=no.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	r600bps(2), r1200bps(3), r2400bps(4), r4800bps(5), r9600bps(6), r19200bps(7), r38400bps(8), r48kbps(9), r56kbps(10), r64kbps(11), r128kbps(12), concentrated(13), notConnected(100), notApplicable(255)

prtInHsiConcentratedTo		1.3.6.1.4.1.164.3.2.3.2.8.2.1.6
The Concentration D Channel of the prtInHsiPrtIdx port. The port always belongs to the same card as prtInHsiPrtIdx port. This object is applicable only when prtInHsiRate=concentrated. Valid values: - notApplicable: 255 - for MP-2200: HS-S12, HS-U12 cards: inPrt37 (137) .. inPrt48 (148). HS-S6, HS-U6 cards: inPrt19 (119) .. inPrt24 (124). - for DXC: HS-U8 cards: 112 .. 254 HS-U16 cards: 112 .. 258. See DXC R6 spec for port index convention.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtExHsrCnfgTable		1.3.6.1.4.1.164.3.2.3.2.10.1
The write operation into the Table Objects is valid only to the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtExHsrCnfgEntry

prtExHsrCnfgEntry		1.3.6.1.4.1.164.3.2.3.2.10.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtExHsrCnfgEntry

prtExHsrCnfgIdx		1.3.6.1.4.1.164.3.2.3.2.10.1.1.1
This object indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtExHsrSltIdx		1.3.6.1.4.1.164.3.2.3.2.10.1.1.2
This object indicates a unique slot position where the card is inserted.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19)

prtExHsrPrtIdx		1.3.6.1.4.1.164.3.2.3.2.10.1.1.3
A unique prt identifier within the card. Valid values: For MP: - For HS-R cards: exPrt1 (1) .. exPrt4 (4) - For HS-U/1 cards: inPrt1 (101) .. inPrt4 (104) - For HS-S12, HS-S6, HS-U12, HS-U6 cards: exPrt1 (1) .. exPrt12 (12). This MIB table is used only for LT-1 interface. For DXC: - For HS-U8, HS-U16 cards: 111 .. 2531 (See DXC R6 spec for port index convention). This MIB table is used only for LT-1 interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtExHsrConnect		1.3.6.1.4.1.164.3.2.3.2.10.1.1.4
This object indicates whether the port should be considered in any of the mux algorithms.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3)

prtExHsrProtocol		1.3.6.1.4.1.164.3.2.3.2.10.1.1.5
This object indicates the protocol.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	sync(2), async(3)

prtExHsrRate		1.3.6.1.4.1.164.3.2.3.2.10.1.1.6
This object indicates the port speed. The 16,32,48,56,64 and 128 kbps rates are applicable only for Sync protocol. The 57.6 and 115.2 kbps rates are applicable only for Async protocol. notConnected= 0 rate.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	r600bps(2), r1200bps(3), r2400bps(4), r4800bps(5), r9600bps(6), r19200bps(7), r38400bps(8), r48kbps(9), r56kbps(10), r64kbps(11), r16000bps(12), r32000bps(13), r57600bps(14), r115200bps(15), r128000bps(16), r7200bps(17), r14400bps(18), r28800bps(19), notConnected(100)

prtExHsrDataBits		1.3.6.1.4.1.164.3.2.3.2.10.1.1.7
Data Bits. This object is applicable for Async protocol only.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	d5bits(1), d6bits(2), d7bits(3), d8bits(4), notApplicable(255)

prtExHsrParity		1.3.6.1.4.1.164.3.2.3.2.10.1.1.8
- For HS-R card, this object indicates if the parity bit is needed or not. Therefore, the 'no' and 'yes; values are applicable. - For HS-S12, HS-U12, the parity type is selected: no, odd, even. This object is applicable for Async protocol only.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3), odd(4), even(5), notApplicable(255)

prtExHsrStopBits		1.3.6.1.4.1.164.3.2.3.2.10.1.1.9
This object indicates the minimum number of stop bits in the tx async frame. This object is applicable for Async protocol only.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	stopBits1Bit(1), stopBits2Bits(2), notApplicable(255)

prtExHsrCts		1.3.6.1.4.1.164.3.2.3.2.10.1.1.10
CTS. This object is applicable for Async protocol only.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	on(2), rts(3), notApplicable(255)

prtExHsrClkMode		1.3.6.1.4.1.164.3.2.3.2.10.1.1.11
Clock mode. This object is applicable for Sync protocol only.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	dce(1), extDce(2), notApplicable(255)

prtExHsrLinkTo		1.3.6.1.4.1.164.3.2.3.2.10.1.1.12
It indicates the slot of the main link card to which the HS-R card is mapped. notApplicable - for HS-U/1 internal ports. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

prtExHsrDcdDsr		1.3.6.1.4.1.164.3.2.3.2.10.1.1.13
DCD & DSR.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), local(2), endToEnd(3)

prtExHsrOperMode		1.3.6.1.4.1.164.3.2.3.2.10.1.1.14
This object indicates the operation mode of the port. normal = bi-directional (Tx/Rx) unidirectRx = unidirectional Rx. broadcast = Tx upon request.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	normal(2), unidirectRx(3), broadcast(4)

prtExHsrRtsDtr		1.3.6.1.4.1.164.3.2.3.2.10.1.1.15
RTS & DTR.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), local(2), endToEnd(3)

prtExHsrLlbEnable		1.3.6.1.4.1.164.3.2.3.2.10.1.1.16
Enable/Disable LLB.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), disabled(2), enabled(3)

prtExHsrRlbEnable		1.3.6.1.4.1.164.3.2.3.2.10.1.1.17
Enable/Disable RLB.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), disabled(2), enabled(3)

prtExHsrRateAdapt		1.3.6.1.4.1.164.3.2.3.2.10.1.1.18
Rate Adaptation - takes a low rate and adapts it to 64Kbps. This object specifies the means this adaptation is done by.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), proprietary(2), v110(3)

prtExHsrRemoteModem		1.3.6.1.4.1.164.3.2.3.2.10.1.1.19
Remote modem. asmi31s2 = ASMi-31/2
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), asmi31(2), asmi31s2(3)

prtExHsrEncapsMode		1.3.6.1.4.1.164.3.2.3.2.10.1.1.20
Low Speed encapsulation method over PCM. When Encapsulation mode is Latency optimized, only rates up to 19.2 are supported. In this case a double number of bits occupy the Time Slot. For up to 9.6 Kbps - 4 bits are occupied. For 14.4 & 19.2 Kbps - 8 bits are occupied. When Encapsulation Mode is Bandwidth Optimized: For up to 9.6 Kbps - 2 bits are occupied. For 14.4 & 19.2 Kbps - 4 bits are occupied. For higher rates - 8 bits are occupied.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), bwOptimized(2), latencyOptimized(3), asmi31(4)

prtExMbeCnfgTable		1.3.6.1.4.1.164.3.2.3.2.11.1
The write operation into the Table Objects is valid only to the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtExMbeCnfgEntry

prtExMbeCnfgEntry		1.3.6.1.4.1.164.3.2.3.2.11.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtExMbeCnfgEntry

prtExMbeCnfgIdx		1.3.6.1.4.1.164.3.2.3.2.11.1.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtExMbeSltIdx		1.3.6.1.4.1.164.3.2.3.2.11.1.1.2
This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

prtExMbePrtIdx		1.3.6.1.4.1.164.3.2.3.2.11.1.1.3
A unique port identifier within the card.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	exPrt1(1)

prtExMbeLan		1.3.6.1.4.1.164.3.2.3.2.11.1.1.4
This attribute indicates whether the MBE port is operated as main or remote bridge.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	remote(1), main(2)

prtInMbeCnfgTable		1.3.6.1.4.1.164.3.2.3.2.11.2
The write operation into the Table Objects is valid only to the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtInMbeCnfgEntry

prtInMbeCnfgEntry		1.3.6.1.4.1.164.3.2.3.2.11.2.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtInMbeCnfgEntry

prtInMbeCnfgIdx		1.3.6.1.4.1.164.3.2.3.2.11.2.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtInMbeSltIdx		1.3.6.1.4.1.164.3.2.3.2.11.2.1.2
This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

prtInMbePrtIdx		1.3.6.1.4.1.164.3.2.3.2.11.2.1.3
A unique port identifier within the card.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	inPrt1(101)

prtInMbeConnect		1.3.6.1.4.1.164.3.2.3.2.11.2.1.4
This attribute indicates whether the port should be considered in any of the mux algorithms.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3)

prtInMbeRate		1.3.6.1.4.1.164.3.2.3.2.11.2.1.5
This attribute indicates the port speed.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	r1x64eq64Kbps(1), r2x64eq128Kbps(2), r3x64eq192Kbps(3), r4x64eq256Kbps(4), r5x64eq320Kbps(5), r6x64eq384Kbps(6), r7x64eq448Kbps(7), r8x64eq512Kbps(8), r9x64eq576Kbps(9), r10x64eq640Kbps(10), r11x64eq704Kbps(11), r12x64eq768Kbps(12), r13x64eq832Kbps(13), r14x64eq896Kbps(14), r15x64eq960Kbps(15), r16x64eq1024Kbps(16), r17x64eq1088Kbps(17), r18x64eq1152Kbps(18), r19x64eq1216Kbps(19), r20x64eq1280Kbps(20), r21x64eq1344Kbps(21), r22x64eq1408Kbps(22), r23x64eq1472Kbps(23), r24x64eq1536Kbps(24)

prtInMbeLinkTo		1.3.6.1.4.1.164.3.2.3.2.11.2.1.6
It indicates the slot of the main link card to which the MBE card is mapped. In the ?004 Unit the entries io6(10)..io16) are not valid. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

prtExTreCnfgTable		1.3.6.1.4.1.164.3.2.3.2.12.1
The write operation into the Table Objects is valid only to the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtExTreCnfgEntry

prtExTreCnfgEntry		1.3.6.1.4.1.164.3.2.3.2.12.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtExTreCnfgEntry

prtExTreCnfgIdx		1.3.6.1.4.1.164.3.2.3.2.12.1.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtExTreSltIdx		1.3.6.1.4.1.164.3.2.3.2.12.1.1.2
This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

prtExTrePrtIdx		1.3.6.1.4.1.164.3.2.3.2.12.1.1.3
A unique port identifier within the card.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	exPrt1(1)

prtExTreLan		1.3.6.1.4.1.164.3.2.3.2.12.1.1.4
This attribute indicates whether the TRE port is operated as main or remote bridge. Default=remote.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	remote(1), main(2)

prtExTreLanRate		1.3.6.1.4.1.164.3.2.3.2.12.1.1.5
This attribute indicates the Rate of the TRE port in Mbit/sec. Default-r4M.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	r4M(1), r16M(2)

prtInTreCnfgTable		1.3.6.1.4.1.164.3.2.3.2.12.2
The write operation into the Table Objects is valid only to the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtInTreCnfgEntry

prtInTreCnfgEntry		1.3.6.1.4.1.164.3.2.3.2.12.2.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtInTreCnfgEntry

prtInTreCnfgIdx		1.3.6.1.4.1.164.3.2.3.2.12.2.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtInTreSltIdx		1.3.6.1.4.1.164.3.2.3.2.12.2.1.2
This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

prtInTrePrtIdx		1.3.6.1.4.1.164.3.2.3.2.12.2.1.3
A unique port identifier within the card.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	inPrt1(101)

prtInTreConnect		1.3.6.1.4.1.164.3.2.3.2.12.2.1.4
This attribute indicates whether the port should be considered in any of the mux algorithms.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3)

prtInTreRate		1.3.6.1.4.1.164.3.2.3.2.12.2.1.5
This attribute indicates the port speed.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	r1x56eq56Kbps(1), r1x64eq64Kbps(2), r2x56eq112Kbps(3), r2x64eq128Kbps(4), r3x56eq168Kbps(5), r3x64eq192Kbps(6), r4x56eq224Kbps(7), r4x64eq256Kbps(8), r5x56eq280Kbps(9), r5x64eq320Kbps(10), r6x56eq336Kbps(11), r6x64eq384Kbps(12), r7x56eq392Kbps(13), r7x64eq448Kbps(14), r8x56eq448Kbps(15), r8x64eq512Kbps(16), r9x56eq504Kbps(17)

prtInTreLinkTo		1.3.6.1.4.1.164.3.2.3.2.12.2.1.6
It indicates the slot of the main link card to which the MBE card is mapped. In the ?004 Unit the entries io6(10)..io16) are not valid. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

prtExPVc4CnfgTable		1.3.6.1.4.1.164.3.2.3.2.9.1
The write operation into the Table Objects is valid only to the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtExPVc4CnfgEntry

prtExPVc4CnfgEntry		1.3.6.1.4.1.164.3.2.3.2.9.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtExPVc4CnfgEntry

prtExPVc4CnfgIdx		1.3.6.1.4.1.164.3.2.3.2.9.1.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtExPVc4SltIdx		1.3.6.1.4.1.164.3.2.3.2.9.1.1.2
This attribute indicates a unique slot position where the card is inserted.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

prtExPVc4PrtIdx		1.3.6.1.4.1.164.3.2.3.2.9.1.1.3
This object indicates the port number in the selected card (slot).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), inPrt1(101), inPrt2(102), inPrt3(103), inPrt4(104), inPrt5(105), inPrt6(106), inPrt7(107), inPrt8(108)

prtExPVc4PrtType		1.3.6.1.4.1.164.3.2.3.2.9.1.1.4
This object indicates the type of the selected port. In Mx 30/300 phase 4: s0 & u are for Voice over ISDN. In MX 30/300 phase 5: sQsig & uQsig are used for Voice over ISDN with Qsig option. In MX MVC4 voice cards, each pair of ports 1-2, 3-4 may have a different type: E&M, FXO, FXS. In MVC4 compressed voice cards ports 1..4 have the same interface for all ports. In MVC8 compressed voice cards each group of ports 1..4, 5..8 may have a different type: E&M, FXO, FXS.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	eAndM(1), fxo(2), fxs(3), internal(4), s0(5), u(6), sQsig(7), uQsig(8)

prtExPVc4Connect		1.3.6.1.4.1.164.3.2.3.2.9.1.1.5
This attribute indicates whether the port should be considered in any of the mux algorithms.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3)

prtExPVc4IfType		1.3.6.1.4.1.164.3.2.3.2.9.1.1.6
This attribute indicates the interface type of the port. eAndM4wires and eAndM2wires - are valid only for E&M port type eAndM4wires - means 2/4 wires fxoGnd and fxoLoop - are valid only for FXO port type fxsGnd and fxsLoop - are valid only for FXS port type e1Framer, e1Slave, t1Framer, t1Slave - are applicable for the mvc4Pbx cards only.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unknown(1), eAndM4wires(2), eAndM2wires(3), fxoGnd(4), fxoLoop(5), fxsGnd(6), fxsLoop(7), e1Framer(8), e1Slave(9), t1Framer(10), t1Slave(11)

prtExPVc4TxGain		1.3.6.1.4.1.164.3.2.3.2.9.1.1.7
Transmission gain in dB.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtExPVc4RxGain		1.3.6.1.4.1.164.3.2.3.2.9.1.1.8
Reception gain in dBm.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtExPVc4MaxRate		1.3.6.1.4.1.164.3.2.3.2.9.1.1.9
Voice rate.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notConnected(1), r4800bps(2), r7200bps(3), r9600bps(4), notApplicatble(255)

prtExPVc4Tc		1.3.6.1.4.1.164.3.2.3.2.9.1.1.10
Time interval for CIR control, in seconds. The value will be the same for all cards' ports.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	t1sec(1), t2sec(2), t3sec(3), t4sec(4)

prtExPVc4Oos		1.3.6.1.4.1.164.3.2.3.2.9.1.1.11
Handling type, when connection is lost.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notSupported(2), forcedIdle(3), forcedBusy(4), busyIdle(5), idleBusy(6)

prtExPVc4EchoCanceler		1.3.6.1.4.1.164.3.2.3.2.9.1.1.12
Echo canceler activation.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

prtExPVc4VarDelay		1.3.6.1.4.1.164.3.2.3.2.9.1.1.13
Maximum variant delay of the FR network, in msec.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..300

prtExPVc4CongLevel		1.3.6.1.4.1.164.3.2.3.2.9.1.1.14
This object indicates the level of delayed data in precents of total available dynamic memory, for which the port will start to operate as congested. The resolution of the parameter is 5%.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..70

prtExPVc4Wire		1.3.6.1.4.1.164.3.2.3.2.9.1.1.15
This object indicates the wiring of the E&M port. It is applicable only for E&M card type.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	w2wire(1), w4wire(2), notApplicable(255)

prtExPVc4ExtensionType		1.3.6.1.4.1.164.3.2.3.2.9.1.1.16
This object indicates the type of extension relevant for this port. ipForceConnect (6) is used for automatic connection or automatic dialing when the phone is off hook (hot line). permanentDial (7) means that the call is established upon power up. The hook may be on or off. Permanent Dialing can be used when there is no signaling. autoAccept (8) means that the called party in the Permanent Dialing will accept the call from the remote side automatically upon on or off hook.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), forceConnect(2), voiceSwitching(3), transparent(4), transparentPlus(5), ipForceConnect(6), permanentDial(7), autoAccept(8)

prtExPVc4ExtensionNumber		1.3.6.1.4.1.164.3.2.3.2.9.1.1.17
This is the extension number of this port. This field is relevant only when the extension type is voice switching and is read only if the port is member of a hunt group.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(2)

prtExPVc4OutPulsing		1.3.6.1.4.1.164.3.2.3.2.9.1.1.18
This field indicates whether to outpulse the received digits. It is notApplicable(1) when the extension type is forceConnect(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), no(2), yes(3)

prtExPVc4HuntGroupMb		1.3.6.1.4.1.164.3.2.3.2.9.1.1.19
This object indicates if this port belongs to an hunt group.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), no(2), yes(3)

prtExPVc4HuntGroupIdx		1.3.6.1.4.1.164.3.2.3.2.9.1.1.20
If it belongs to an hunt group, this fields indicates the index of the relevant hunt group. 0 = notApplicable
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..10

prtExPVc4AutoFaxMode		1.3.6.1.4.1.164.3.2.3.2.9.1.1.21
This object indicates if the system will switch automatically to FAX mode when detecting FAX activity. Default=Yes.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), no(2), yes(3)

prtExPVc4FaxRate		1.3.6.1.4.1.164.3.2.3.2.9.1.1.22
FAX initial rate. Default=9600 bps.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notConnected(1), r4800bps(2), r7200bps(3), r9600bps(4), r12000bps(5), r14400bps(6), r2400bps(7), vbdFax(8)

prtExPVc4SeizeAck		1.3.6.1.4.1.164.3.2.3.2.9.1.1.23
This parameter shows whether the device will acknowledge a seize signal (On/Off Hook). When the value is set to yes(3) & the device receives an on/off hook signal it will transmit back an on/off hook signal. When the value is set to no(2) & the device receives an on/off hook signal it will NOT transmit back an on/off hook signal. Example: If Seize Ack Parameter = YES, when the MVC.4 receives a seize signal (Off Hook) from the PBX it will send an Off Hook to the PBX. The Seize Parameter is relevant for all the following cards: MVC-4 MVC-4/E1-Framer MVC-4/T1-DSU-Framer MVC-4/T1-CSU-Framer MVC-4/E1-SLAVE MVC-4/T1-SLAVE Default values: Analog FXS - No (value can't be changed). Analog FXO - Yes (value can't be changed). Analog E&M - No (values NO/YES). Digital E1/T1 Framer & Slave - No.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3)

prtExPVc4SignalingProtocol		1.3.6.1.4.1.164.3.2.3.2.9.1.1.24
The signaling protocol that will be used between the PABX & the voice port. Delay Start Protocol: the line is seized by sending an Off hook signal and after a delay, if the called party is available (On hook) DTMF (Dual Tone Multi Frequency) digits are sent towards the called party. Immediate Start Protocol: the line is seized by sending an Off Hook signal and immediately DTMF digits are sent towards the called party. Wink start protocol: the line is seized by sending an Off Hook signal and then the called party sends a short Off Hook wink signal. Now the calling party starts sending DTMF digits.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	delayStart(2), immediateStart(3), winkStart(4)

prtExPVc4DelayStart		1.3.6.1.4.1.164.3.2.3.2.9.1.1.25
This parameter is used only for Delay Protocol. This is the time that the calling party will wait after sending an Off hook signal and before sending DTMF digits to the called party. The delay values are 100..5000 msec in intervals of 100 msec.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtExPVc4WinkMinDuration		1.3.6.1.4.1.164.3.2.3.2.9.1.1.26
This parameter is used only for Wink Protocol. Min Duration of the Wink Signal (off hook duration from the called party). Legal values: 40..400 msec in intervals of 10 msec.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtExPVc4WinkMaxDuration		1.3.6.1.4.1.164.3.2.3.2.9.1.1.27
This parameter is used only for Wink Protocol. Max Duration of the Wink Signal (off hook duration from the called party). Legal values: 40..400 msec in intervals of 10 msec.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtExPVc4GenerateTone		1.3.6.1.4.1.164.3.2.3.2.9.1.1.28
This parameter indicates whether the device (MX or MPH) should generate dial tones for the channel. If the value is yes (3), it generates dial tones. If the value is no (2), the connected equipment will generate dial tones. For example for some ISDN sets the dial tone is generated by the phone itself while for others sets it is generated by the MX.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), no(2), yes(3)

prtExPVc4CodingLaw		1.3.6.1.4.1.164.3.2.3.2.9.1.1.29
This attribute indicates the Method/Law for decoding/encoding the voice information. aLaw(1) is the standard Law for E1 links. uLaw(2) is the standard Law for T1 links. This object is equal for all the ports in the specific module because of HW limitations
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	aLAW(1), uLAW(2)

prtExPVc4GenerateRingBack		1.3.6.1.4.1.164.3.2.3.2.9.1.1.30
Determines whether the Ring Back tone is generated locally or from the remote end. The default is - NO (Meaning coming from the remote end). Yes means that the Ring Back Tone is generated locally. Applicable only for Force Connect.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), no(2), yes(3)

prtExPVc4ChannelId		1.3.6.1.4.1.164.3.2.3.2.9.1.1.31
Channel Identifier. According to FRF11 each voice port that works as force connect should add a CH Id after the DLCI in the frame header. Default : 1 Applicable only for Force Connect. Not Applicable value will be 0.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..256

prtExPVc4PortConnection		1.3.6.1.4.1.164.3.2.3.2.9.1.1.32
Port connection determines whether the port is connected to a PABX (Trunk) or to Telephone set (Line) . It determines whether to send certain messages to the port or not. If the type is LINE then the port generates a ring back tone , if TRUNK it doesn't (The PBX does it).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), line(2), trunk(3)

prtExPVc4CoderAndRate		1.3.6.1.4.1.164.3.2.3.2.9.1.1.33
Coder and Rate for the Voice Compression. In MPH: Relevant for MVC-8 card only.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), g7231r6300BPS(2), g7231r5300BPS(3), g729A8KBPS(4), g711aLAW(5), g711uLAW(6), g726r16KBPS(7), g726r24KBPS(8), g726r32KBPS(9), g726r40KBPS(10), g727r16KBPS(11), g727r24r16KBPS(12), g727r24KBPS(13), g727r16r32KBPS(14), g727r32r24KBPS(15), g727r32KBPS(16), g727r40r16KBPS(17), g727r40r24KBPS(18), g727r40r32KBPS(19), transparent(20), netcoder6400BPS(21), netcoder7200BPS(22), netcoder8KBPS(23), netcoder8800BPS(24), netcoder9600BPS(25), lowBitRateR2660BPS(26), amr4750BPS(27), amr5150BPS(28), amr5900BPS(29), amr6700BPS(30), amr7400BPS(31), amr7950BPS(32), amr10200BPS(33), amr12200BPS(34)

prtExPVc4DestinationNum		1.3.6.1.4.1.164.3.2.3.2.9.1.1.34
The destination phone number: 0 to 22 digits. Applicable for Auto Dial - ipForceConnect(6), Permanent Dial and Auto Accept Extension Types. Default: Null String
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

prtExPVc4DtmfRelay		1.3.6.1.4.1.164.3.2.3.2.9.1.1.35
When DTMF RELAY is disabled, the DTMF digits (dialed by the user) are transmitted as compressed voice and in the remote unit are decompressed. When DTMF RELAY is enabled, the DTMF digits are detected at the near side and not transmitted as voice. Instead, only an indication of what digits were dialed are transmitted and in the far end the tone is regenerated.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(2), enable(3)

prtExPVc4DiscOnSilence		1.3.6.1.4.1.164.3.2.3.2.9.1.1.36
No. of silenced seconds after which the call will be disconected. A value of 0 means that there will be no disconnect when there is silence. Possible values: 0 - 900 sec.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtExPVc4DynamicJitter		1.3.6.1.4.1.164.3.2.3.2.9.1.1.37
The MVC8 uses two mechanisms to overcome the network delay. The first one is a static jitter buffer which holds a constant buffer of up to 300 Msec and can be controled by the JITTER parameter (prtExPVc4VarDelay). The second one is the dynamic jitter which calculates, in real time, the network delay and handles a jitter buffer dynamically. The dynamic mechanism that is implemented in MVC8, was intended to overcome network delay yet when the network bursts, the MVC8 dynamic mechanism is not able to overcome the delay. Therefore it is better not to use the dynamic jitter (DISABLE - should be the default) where bursts may occur often.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(2), enable(3)

prtExPVc4EandMType		1.3.6.1.4.1.164.3.2.3.2.9.1.1.38
This is the signaling type on the E&M analog side. The analog signaling includes voltage, no. of pins and other parameters.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), type1(2), type2(3), type3(4), ssdc5(5)

prtExPVc4Rate		1.3.6.1.4.1.164.3.2.3.2.9.1.1.39
This is the Rate of the port in TS units. It is used by VF-30 card family. 0 = NA = port is not intended to be connected; therefore, no Rate.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..31

prtExPVc4FrameSize		1.3.6.1.4.1.164.3.2.3.2.9.1.1.40
Defines the maximum size in Bytes of the multiplexed frame. In some cases this must be limited to avoid IP fragmentation, which makes the multiplexing useless, and can also decrease the damage in case of frame loss. Valid range: 100..1461. notApplicable=0.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtExPVc4MultiplexInterval		1.3.6.1.4.1.164.3.2.3.2.9.1.1.41
Defines the maximum amout of time (msec.) between multiplexed frames that are sent. For Vmux-400/420 devices: It defines the Payload Packetizing Interval. Valid values: 10-90 msec. notApplicable=0.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtExPVc4TransportProtocol		1.3.6.1.4.1.164.3.2.3.2.9.1.1.42
Transport Protocol. ptp = point to point. aal2oMpls = AAL2 over MPLS.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), ptp(2), aal2oMpls(3)

prtExPVc4MultiFreqRelay		1.3.6.1.4.1.164.3.2.3.2.9.1.1.43
This object enables/disables Multi Frequency Signaling Detection.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), enable(3)

prtExPVc4MinPulseWidth		1.3.6.1.4.1.164.3.2.3.2.9.1.1.44
Defines the minimum Pulse Width in msec. Valid values: 45-100 msec. notApplicable=0.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtExPVc4MinPowerLevel		1.3.6.1.4.1.164.3.2.3.2.9.1.1.45
Defines the minimum Power Level in dBm. Valid values: -1..-35 dBm.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtExPVc4SuperTandem		1.3.6.1.4.1.164.3.2.3.2.9.1.1.46
The Super Tandem feature provides end to end compression over multiple hops, solving the double compression problem detected in Voice compressing systems. The Super Tandem, when enabled, allows transmission of compressed voice between a few devices and eliminates the need to decompress an recompress it over each voice card and PBX, thus improving voice quality and reducing delay.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), enable(3)

prtExPVc4DestIp		1.3.6.1.4.1.164.3.2.3.2.9.1.1.47
This object defines the destination IP Address.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

prtExPVc4DestBundle		1.3.6.1.4.1.164.3.2.3.2.9.1.1.48
This object defines the destination Bundle at the far-end device.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtExPVc4SrcIpAddress		1.3.6.1.4.1.164.3.2.3.2.9.1.1.49
This object defines the Source IP Address.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

prtExPVc4SrcIpMask		1.3.6.1.4.1.164.3.2.3.2.9.1.1.50
This object defines the Source IP Mask.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

prtExPVc4DefaultGateway		1.3.6.1.4.1.164.3.2.3.2.9.1.1.51
This object defines the Default Gateway for this interface.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

prtExPVc4SigPacketInterval		1.3.6.1.4.1.164.3.2.3.2.9.1.1.52
Defines the Signaling Packetizing Interval, which is the maximum time interval, measured in msec (milliseconds), between multiplexed signaling frames.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

prtExPVc4DlciTable		1.3.6.1.4.1.164.3.2.3.2.9.2
The write operation into the Table Objects is valid only at the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtExPVc4DlciEntry

prtExPVc4DlciEntry		1.3.6.1.4.1.164.3.2.3.2.9.2.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtExPVc4DlciEntry

prtExPVc4DlciCnfgIdx		1.3.6.1.4.1.164.3.2.3.2.9.2.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtExPVc4DlciSltIdx		1.3.6.1.4.1.164.3.2.3.2.9.2.1.2
This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

prtExPVc4DlciPrtIdx		1.3.6.1.4.1.164.3.2.3.2.9.2.1.3
This attribute indicates a unique internal port number. VC4 cards have four external ports.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4)

prtExPVc4DlciValid		1.3.6.1.4.1.164.3.2.3.2.9.2.1.4
This attribute indicates whether the attributes in this entry are valid or not. The user can add/delete pvc (dlci to dlci connection) by modifing this object
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3)

prtExPVc4DlciIConSlt		1.3.6.1.4.1.164.3.2.3.2.9.2.1.5
This attribute indicates a unique slot position In the Mux (Agent) where the dlci is routed to. In the ?004 Unit the entries io6(10)..io16) are not valid
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noConnect(2), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

prtExPVc4DlciIConPrt		1.3.6.1.4.1.164.3.2.3.2.9.2.1.6
This attribute indicates a unique port id which the dlci is routed to.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), exPrt5(5), exPrt6(6), exPrt7(7), exPrt8(8), exPrt9(9), exPrt10(10), noConnect(100), inPrt1(101), inPrt2(102), inPrt3(103), inPrt4(104), inPrt5(105), inPrt6(106), inPrt7(107), inPrt8(108), inPrt9(109), inPrt10(110), inPrt11(111), inPrt12(112)

prtExPVc4DlciIConDlci		1.3.6.1.4.1.164.3.2.3.2.9.2.1.7
This attribute indicates a unique internal connection dlci number, the dlci is routed to.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..991

prtExPVc4DlciTxBc		1.3.6.1.4.1.164.3.2.3.2.9.2.1.8
This attribute indicates a unique Tx committed bandwidth on the user transmit line (or at the port receive line).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	full(1), zero(2), txBc9600bps(3), txBc14400bps(4), txBc19200bps(5), txBc28800bps(6), txBc32000bps(7), txBc38400bps(8), txBc48000bps(9), txBc56000bps(10), txBc57600bps(11), txBc64Kbps(12), txBc128Kbps(13), txBc192Kbps(14), txBc256Kbps(15), txBc320Kbps(16), txBc384Kbps(17), txBc448Kbps(18), txBc512Kbps(19), txBc768Kbps(20), txBc1024Kbps(21), txBc16000bps(25), txBc112Kbps(26)

prtExPVc4DlciTxBe		1.3.6.1.4.1.164.3.2.3.2.9.2.1.9
This attribute indicates a unique Tx excess bandwidth on the user transmit line (or at the port receive line).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	full(1), zero(2), txBe9600bps(3), txBe14400bps(4), txBe19200bps(5), txBe28800bps(6), txBe32000bps(7), txBe38400bps(8), txBe48000bps(9), txBe56000bps(10), txBe57600bps(11), txBe64Kbps(12), txBe128Kbps(13), txBe192Kbps(14), txBe256Kbps(15), txBe320Kbps(16), txBe384Kbps(17), txBe448Kbps(18), txBe512Kbps(19), txBe768Kbps(20), txBe1024Kbps(21), txBc16000bps(25), txBc112Kbps(26)

prtExPVc4DlciRxBc		1.3.6.1.4.1.164.3.2.3.2.9.2.1.10
This attribute indicates a unique Rx committed bandwidth on the user receive line (or at the port transmit line).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	full(1), zero(2), rxBc9600bps(3), rxBc14400bps(4), rxBc19200bps(5), rxBc28800bps(6), rxBc32000bps(7), rxBc38400bps(8), rxBc48000bps(9), rxBc56000bps(10), rxBc57600bps(11), rxBc64Kbps(12), rxBc128Kbps(13), rxBc192Kbps(14), rxBc256Kbps(15), rxBc320Kbps(16), rxBc384Kbps(17), rxBc448Kbps(18), rxBc512Kbps(19), rxBc768Kbps(20), rxBc1024Kbps(21), rxBc16000bps(25), rxBc112Kbps(26)

prtExPVc4DlciRxBe		1.3.6.1.4.1.164.3.2.3.2.9.2.1.11
This attribute indicates a unique Rx excess bandwidth on the user receive line (or at the port transmit line).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	full(1), zero(2), rxBe9600bps(3), rxBe14400bps(4), rxBe19200bps(5), rxBe28800bps(6), rxBe32000bps(7), rxBe38400bps(8), rxBe48000bps(9), rxBe56000bps(10), rxBe57600bps(11), rxBe64Kbps(12), rxBe128Kbps(13), rxBe192Kbps(14), rxBe256Kbps(15), rxBe320Kbps(16), rxBe384Kbps(17), rxBe448Kbps(18), rxBe512Kbps(19), rxBe768Kbps(20), rxBe1024Kbps(21), rxBc16000bps(25), rxBc112Kbps(26)

prtExPVc4DlciPriority		1.3.6.1.4.1.164.3.2.3.2.9.2.1.12
This attribute indicates a unique priority of the pvc. 6 is the lowest priority and 8 is the highest priority.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	6..8

prtExPVc4DlciStatus		1.3.6.1.4.1.164.3.2.3.2.9.2.1.13
This attribute indicates the status of the pvc. The status is disconnected(1) when one of the sides is programmed as not connected
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	disconnected(1), connected(2)

prtExLs6CnfgTable		1.3.6.1.4.1.164.3.2.3.2.13.1
The write operation into the Table Objects is valid only to the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtExLs6CnfgEntry

prtExLs6CnfgEntry		1.3.6.1.4.1.164.3.2.3.2.13.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtExLs6CnfgEntry

prtExLs6CnfgIdx		1.3.6.1.4.1.164.3.2.3.2.13.1.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtExLs6SltIdx		1.3.6.1.4.1.164.3.2.3.2.13.1.1.2
This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

prtExLs6PrtIdx		1.3.6.1.4.1.164.3.2.3.2.13.1.1.3
This attribute indicates a unique port index.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), exPrt5(5), exPrt6(6), exPrt7(7), exPrt8(8), exPrt9(9), exPrt10(10), exPrt11(11), exPrt12(12)

prtExLs6Connect		1.3.6.1.4.1.164.3.2.3.2.13.1.1.4
This attribute indicates whether the port should be considered in any of the mux algorithms.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3)

prtExLs6Protocol		1.3.6.1.4.1.164.3.2.3.2.13.1.1.5
This attribute indicates the protocol. async - can be selected only for ports 1-2.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	sync(2), async(3)

prtExLs6Rate		1.3.6.1.4.1.164.3.2.3.2.13.1.1.6
Port rates in bps. g1 - contains the values : (2)-(6),(9),(12),(16) g2 - contains the values : (7),(10),(14),(19) g3 - contains the values : (8),(11),(13),(15),(17),(18),(20); it is not applicable when using Async protocol. Rates of pair ports (1-2, 3-4, 5-6) must be from the same group.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	r300bps(2), r600bps(3), r1200bps(4), r2400bps(5), r4800bps(6), r7200bps(7), r8000bps(8), r9600bps(9), r14400bps(10), r16000bps(11), r19200bps(12), r24000bps(13), r28800bps(14), r32000bps(15), r38400bps(16), r48000bps(17), r56000bps(18), r57600bps(19), r64000bps(20)

prtExLs6ClkMode		1.3.6.1.4.1.164.3.2.3.2.13.1.1.7
This attribute indicates a unique port operation clock mode. It is applicable for Sync protocol only .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	dce(1), extDce(2), dte1(3), notApplicable(255)

prtExLs6CtrlSignal		1.3.6.1.4.1.164.3.2.3.2.13.1.1.8
Control Signal.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	local(2), rts(3), dtrAndRts(4)

prtExLs6DataBits		1.3.6.1.4.1.164.3.2.3.2.13.1.1.9
Data Bits. This object is applicable for Async protocol only.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	d6bits(1), d7bits(2), d8bits(3), d9bits(4), notApplicable(255)

prtExLs6Cts		1.3.6.1.4.1.164.3.2.3.2.13.1.1.10
This object indicates the CTS control line operation mode.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), on(2), rts(3)

prtExLs6LinkToInternal		1.3.6.1.4.1.164.3.2.3.2.13.1.1.11
This object indicates which internal port of the card, the external port is linked to.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	inPrt1(101), inPrt2(102), notApplicable(255)

prtExLs6VCnfgTable		1.3.6.1.4.1.164.3.2.3.2.13.2
The write operation into the Table Objects is valid only to the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtExLs6VCnfgEntry

prtExLs6VCnfgEntry		1.3.6.1.4.1.164.3.2.3.2.13.2.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtExLs6VCnfgEntry

prtExLs6VCnfgIdx		1.3.6.1.4.1.164.3.2.3.2.13.2.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtExLs6VSltIdx		1.3.6.1.4.1.164.3.2.3.2.13.2.1.2
This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

prtExLs6VPrtIdx		1.3.6.1.4.1.164.3.2.3.2.13.2.1.3
A unique identifier of the port, within the card.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	exPrt7(7), exPrt8(8)

prtExLs6VConnect		1.3.6.1.4.1.164.3.2.3.2.13.2.1.4
This attribute indicates whether the port should be considered in any of the mux algorithms.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3)

prtExLs6VRate		1.3.6.1.4.1.164.3.2.3.2.13.2.1.5
Rate (bps) used for FAX transmission and Voice coding.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	r6400bps(2), r7200bps(3), r8000bps(4), r9600bps(5), r16000bps(6), r24000bps(7), r32000bps(8), r64000bps(9)

prtExLs6VEchoCanceler		1.3.6.1.4.1.164.3.2.3.2.13.2.1.6
Echo canceler activation.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

prtExLs6VIfType		1.3.6.1.4.1.164.3.2.3.2.13.2.1.7
This attribute indicates the interface type of the port. w4wire - is applicable only for E&M port type.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	w2wire(1), w4wire(2)

prtExLs6VTxGain		1.3.6.1.4.1.164.3.2.3.2.13.2.1.8
Transmit gain in dBm. E&M - values range: -17 .. 8 FXO - values range: -16 .. 4 FXS - values range: -13 .. 8
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtExLs6VRxGain		1.3.6.1.4.1.164.3.2.3.2.13.2.1.9
Receive gain in dBm. E&M - values range: -17 .. 2 FXO - values range: -17 .. -1 FXS - values range: -17 .. 2
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtExLs6VOos		1.3.6.1.4.1.164.3.2.3.2.13.2.1.10
Out of Service signaling mode.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	forcedIdle(1), forcedBusy(2), busyIdle(3), idleBusy(4)

prtInLs6CnfgTable		1.3.6.1.4.1.164.3.2.3.2.13.3
The write operation into the Table Objects is valid only to the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtInLs6CnfgEntry

prtInLs6CnfgEntry		1.3.6.1.4.1.164.3.2.3.2.13.3.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtInLs6CnfgEntry

prtInLs6CnfgIdx		1.3.6.1.4.1.164.3.2.3.2.13.3.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtInLs6SltIdx		1.3.6.1.4.1.164.3.2.3.2.13.3.1.2
This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

prtInLs6PrtIdx		1.3.6.1.4.1.164.3.2.3.2.13.3.1.3
This attribute indicates a unique internal port index.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	inPrt1(101), inPrt2(102)

prtInLs6Connect		1.3.6.1.4.1.164.3.2.3.2.13.3.1.4
This attribute indicates whether the port should be considered in any of the mux algorithms. It also affects all the module considerations because the module has only one Internal interface which is the composite channel.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3)

prtInLs6TandemMode		1.3.6.1.4.1.164.3.2.3.2.13.3.1.5
This object indicates the Tandem Mode. tandemSlave - is valid only for an LS-6 card having on the (current slot-1) an LS-6 card with 'tandemMaster' mode.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noTandem(1), tandemMaster(2), tandemSlave(3)

prtInLs6Rate		1.3.6.1.4.1.164.3.2.3.2.13.3.1.6
Main Rate in Kbps.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	r32Kbps(1), r56Kbps(2), r64Kpbs(3), r128Kbps(4), r256Kbps(5), r384Kbps(6), r192Kbps(7), r512Kbps(8), r768Kbps(9), r14400bps(10)

prtInLs6RemoteType		1.3.6.1.4.1.164.3.2.3.2.13.3.1.7
Remote Type. notApplicable - when prtInLs6TandemMode=tandemSlave
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ls6(1), km2kSlave(2), km2kStandalone(3), notApplicable(255)

prtInLs6LinkTo		1.3.6.1.4.1.164.3.2.3.2.13.3.1.8
It indicates the slot of the main link card to which the Ls6 card is mapped. In the ?004 Unit the entries io6(10)..io12(16) are not valid. notApplicable - when prtInLs6TandemMode=tandemSlave. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

prtExVc3CnfgTable		1.3.6.1.4.1.164.3.2.3.2.14.1
The write operation into the Table Objects is valid only to the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtExVc3CnfgEntry

prtExVc3CnfgEntry		1.3.6.1.4.1.164.3.2.3.2.14.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtExVc3CnfgEntry

prtExVc3CnfgIdx		1.3.6.1.4.1.164.3.2.3.2.14.1.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtExVc3SltIdx		1.3.6.1.4.1.164.3.2.3.2.14.1.1.2
This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

prtExVc3PrtIdx		1.3.6.1.4.1.164.3.2.3.2.14.1.1.3
A unique identifier of the port, within the card.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	exPrt1(1), exPrt2(2), exPrt3(3)

prtExVc3Connect		1.3.6.1.4.1.164.3.2.3.2.14.1.1.4
This attribute indicates whether the port should be considered in any of the mux algorithms.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3)

prtExVc3TransGain		1.3.6.1.4.1.164.3.2.3.2.14.1.1.5
Transmit gain in dBm.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtExVc3ReceiveGain		1.3.6.1.4.1.164.3.2.3.2.14.1.1.6
Receive gain in dBm.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtExVc3Wire		1.3.6.1.4.1.164.3.2.3.2.14.1.1.7
This object is equal for all the ports in the specific card because of HW limitations
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	w2wire(1), w4wire(2)

prtExVc3Rate		1.3.6.1.4.1.164.3.2.3.2.14.1.1.8
Rate in bps.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	r9600bps(1), r4800bps(2)

prtExVc3EchoCanceler		1.3.6.1.4.1.164.3.2.3.2.14.1.1.9
Echo canceler activation. The value will be the same for all the card's external ports.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

prtInVc3CnfgTable		1.3.6.1.4.1.164.3.2.3.2.14.2
The write operation into the Table Objects is valid only to the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtInVc3CnfgEntry

prtInVc3CnfgEntry		1.3.6.1.4.1.164.3.2.3.2.14.2.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtInVc3CnfgEntry

prtInVc3CnfgIdx		1.3.6.1.4.1.164.3.2.3.2.14.2.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtInVc3SltIdx		1.3.6.1.4.1.164.3.2.3.2.14.2.1.2
This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

prtInVc3PrtIdx		1.3.6.1.4.1.164.3.2.3.2.14.2.1.3
A unique identifier of the port, within the card.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	inPrt1(101)

prtInVc3Connect		1.3.6.1.4.1.164.3.2.3.2.14.2.1.4
This attribute indicates whether the port should be considered in any of the mux algorithms.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3)

prtInVc3Rate		1.3.6.1.4.1.164.3.2.3.2.14.2.1.5
Rate in bps.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	r32000bps(1), r16000bps(2)

prtInVc3Oos		1.3.6.1.4.1.164.3.2.3.2.14.2.1.6
This object is equal for all the ports in the specific card because of HW limitations
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	forcedIdle(1), forcedBusy(2), busyIdle(3), idleBusy(4)

prtInVc3LinkTo		1.3.6.1.4.1.164.3.2.3.2.14.2.1.7
This attribute indicates the slot of the ML card to which the VC card is mapped. In the ?004 Unit the entries io6(10)..io12(16) are not valid. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

prtExVcPbxCnfgTable		1.3.6.1.4.1.164.3.2.3.2.15.1
The write operation into the Table Objects is valid only to the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtExVcPbxCnfgEntry

prtExVcPbxCnfgEntry		1.3.6.1.4.1.164.3.2.3.2.15.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtExVcPbxCnfgEntry

prtExVcPbxCnfgIdx		1.3.6.1.4.1.164.3.2.3.2.15.1.1.1
This object indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtExVcPbxSltIdx		1.3.6.1.4.1.164.3.2.3.2.15.1.1.2
This object indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

prtExVcPbxPrtIdx		1.3.6.1.4.1.164.3.2.3.2.15.1.1.3
A unique identifier of the port, within the card.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	exPrt1(1)

prtExVcPbxConnect		1.3.6.1.4.1.164.3.2.3.2.15.1.1.4
This object indicates whether the port should be considered in any of the mux algorithms.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3)

prtExVcPbxGroup		1.3.6.1.4.1.164.3.2.3.2.15.1.1.5
The group object links together several VC-PBX cards, concerning compression of the same input T1/E1 link time-slots. When ports of different slots have the same group, they are linked. When ports have a different group, they are not linked. For VC-PBX/T1 and E1 cards, this object is - their own IO Slot. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

prtExVcPbxTransparent		1.3.6.1.4.1.164.3.2.3.2.15.1.1.6
This object indicates whether the Transparent transfer of Time-Slots is required or not. Time-Slots transferred by Transparent, will not be compressed. no - applicable only for VC-PBX/T1 and VC-PBX/E1 cards yes - applicable only for VC-PBX/T1 and VC-PBX/E1 cards notApplicable - only for VC-PBX cards.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3), notApplicable(255)

prtExVcPbxTransSignalTs		1.3.6.1.4.1.164.3.2.3.2.15.1.1.7
This object specifies the ML Time-Slot dedicated to the signaling of the PABX Transparent TSs. None = 255. When prtExVcPbxTransparent=no this object's value=None (255) When prtExVcPbxTransparent=notApplicable, this object's value=None (255). When prtExVcPbxTransparent=yes: - for VC-PBX/T1 ports, this object's valid values are 1..16 or None (255). - for VC-PBX/E1 ports, this object's value will be 16 or None (255).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtExVcPbxFrame		1.3.6.1.4.1.164.3.2.3.2.15.1.1.8
This object is the frame parameter for T1/E1 interface. The user should select only the parameters which are relevant to the specific card: T1 values for the VC-PBX/T1 card. E1 values for the VC-PBX/E1 card. notApplicable - for the VC-PBX card. This parameter has the same values as dsx1LineType in T1/E1 MIB (RFC-1406). The parameters in dsx1LineType are: other (1) esfT1 dsx1ESF (2) sfT1 dsx1D4 (3) g732nE1 dsx1E1 (4) g732nE1CRC dsx1E1-CRC (5) g732sE1 dsx1E1-MF (6) g732sE1CRC dsx1E1-MF-CRC (7)
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	esfT1(2), sfT1(3), g732nE1(4), g732nE1CRC(5), g732sE1(6), g732sE1CRC(7), notApplicable(255)

prtExVcPbxRestoreTime		1.3.6.1.4.1.164.3.2.3.2.15.1.1.9
The time passing from the disappearance of the loss of synchronization condition (red alarm) to the restoration of normal service. The options 1secFast(2) and 10sec62411(3) for E1 interfaces are proprietary implementation of the T1 standard to the E1 interface. ccittE1 - is applicable only for VC-PBX/E1 card notApplicable - is applicable for VC-PBX card
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	restoreT1secFast(2), restoreT10sec62411(3), ccittE1(4), notApplicable(255)

prtExVcPbxLineCode		1.3.6.1.4.1.164.3.2.3.2.15.1.1.10
This object is the line code parameter used for T1/E1 interface. The user should select only the parameters which are relevant to the specific card: T1 line code parameters for VC-PBX/T1 E1 line code parameters for VC-PBX/E1 notApplicable - for VC-PBX This parameter has the same values as dsx1LineCoding in T1/E1 MIB (RFC-1406). The parameters in dsx1LineCoding are: dsx1JBZS (1) dsx1B8ZS (2) dsx1HDB3 (3) dsx1ZBTSI (4) dsx1AMI (5) other (6)
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	b7zsT1(1), b8zsT1(2), transT1(3), hdb3E1(4), notApplicable(255)

prtExVcPbxLineLength		1.3.6.1.4.1.164.3.2.3.2.15.1.1.11
This object is the line length parameter. It is applicable only for the VC-PBX/T1 card. notApplicable - for the VC-PBX and VC-PBX/E1 card. lenXXXpXXXft = len-XXX-XXXft.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unknown(1), len0p133ft(2), len134p266ft(3), len267p399ft(4), len400p533ft(5), len534p655ft(6), notApplicable(255)

prtExVcPbxLinkTo		1.3.6.1.4.1.164.3.2.3.2.15.1.1.12
This object indicates the slot of the ML card to which the VC-PBX/T1, VC-PBX/E1 card Transparent TSs are mapped. notApplicable - for VC-PBX card AND for VC-PBX/T1, VC-PBX/E1 cards, when prtExVcPbxTransparent=no . In the ?004 Unit the entries io6(10)..io12(16) are not valid. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

prtExVcPbxSignalOper		1.3.6.1.4.1.164.3.2.3.2.15.1.1.13
This object indicates the Signaling Operation of the VC-PBX/T1, VC-PBX/E1 external port. notApplicable - for VC-PBX card normal - all 4 signaling bits are transferred. bEqA - copy the A bit into the B bit. Applicable only for VC-PBX/T1.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), normal(2), bEqA(3), inverseA(4)

prtExVcPbxIdleCode		1.3.6.1.4.1.164.3.2.3.2.15.1.1.14
Determines the code for transmission in empty time slots. notApplicable - for VC-PBX card .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), hff(2), he4(3), hd5(4), h9e(5), h98(6), h7f(7), h7e(8), h54(9), h1a(10)

prtIn1p6VcPbxCnfgTable		1.3.6.1.4.1.164.3.2.3.2.15.2
The write operation into the Table Objects is valid only to the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtIn1p6VcPbxCnfgEntry

prtIn1p6VcPbxCnfgEntry		1.3.6.1.4.1.164.3.2.3.2.15.2.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtIn1p6VcPbxCnfgEntry

prtIn1p6VcPbxCnfgIdx		1.3.6.1.4.1.164.3.2.3.2.15.2.1.1
This object indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtIn1p6VcPbxSltIdx		1.3.6.1.4.1.164.3.2.3.2.15.2.1.2
This object indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

prtIn1p6VcPbxPrtIdx		1.3.6.1.4.1.164.3.2.3.2.15.2.1.3
A unique identifier of the port, within the card.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	inPrt1(101), inPrt2(102), inPrt3(103), inPrt4(104), inPrt5(105), inPrt6(106)

prtIn1p6VcPbxConnect		1.3.6.1.4.1.164.3.2.3.2.15.2.1.4
This object indicates whether the port should be considered in any of the mux algorithms.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3)

prtIn1p6VcPbxRate		1.3.6.1.4.1.164.3.2.3.2.15.2.1.5
This object indicates the port Rate. For Normal mode (prtIn7p8VcPbxMode=normal), only part of the values are valid (constant rate). For Server mode (prtIn7p8VcPbxMode=server), all values are applicable (user can select the desired compression rate).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	r4800bps(1), r6400bps(2), r7200bps(3), r8000bps(4), r9600bps(5), r12800bps(6)

prtIn1p6VcPbxEchoCanceler		1.3.6.1.4.1.164.3.2.3.2.15.2.1.6
Echo canceler activation.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

prtIn1p6VcPbxPabxTs		1.3.6.1.4.1.164.3.2.3.2.15.2.1.7
This object defines the PABX Time-Slot assigned to this internal port. For a T1 link, the valid values are: 1 .. 24. For an E1 link, the valid values are: 1 .. 31. This object is NOT applicable when prtIn1p6VcPbxConnect=no. This object is applicable for all cards of VC-PBX family. Default=the internal port index (1..6).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..31

prtIn7p8VcPbxCnfgTable		1.3.6.1.4.1.164.3.2.3.2.15.3
The write operation into the Table Objects is valid only to the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtIn7p8VcPbxCnfgEntry

prtIn7p8VcPbxCnfgEntry		1.3.6.1.4.1.164.3.2.3.2.15.3.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtIn7p8VcPbxCnfgEntry

prtIn7p8VcPbxCnfgIdx		1.3.6.1.4.1.164.3.2.3.2.15.3.1.1
This object indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtIn7p8VcPbxSltIdx		1.3.6.1.4.1.164.3.2.3.2.15.3.1.2
This object indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

prtIn7p8VcPbxPrtIdx		1.3.6.1.4.1.164.3.2.3.2.15.3.1.3
A unique identifier of the port, within the card.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	inPrt7(107), inPrt8(108)

prtIn7p8VcPbxConnect		1.3.6.1.4.1.164.3.2.3.2.15.3.1.4
This object indicates whether the port should be considered in any of the mux algorithms.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3)

prtIn7p8VcPbxMode		1.3.6.1.4.1.164.3.2.3.2.15.3.1.5
This object indicates the working mode of the port: - normal - the compressed voice will be sent to an MTML card inside the Mux. - server - the compressed voice will be sent to the Digital Voice connector, as a service to an outside user.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	normal(1), server(2)

prtIn7p8VcPbxRate		1.3.6.1.4.1.164.3.2.3.2.15.3.1.6
This object indicates the port Main Rate. For Server mode (prtIn7p8VcPbxMode=server), the value will be notApplicable.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	r32Kbps(1), r16Kbps(2), notApplicable(255)

prtIn7p8VcPbxSignalMode		1.3.6.1.4.1.164.3.2.3.2.15.3.1.7
This object indicates the Signal Mode. For Server mode (prtIn7p8VcPbxMode=server), the only valid values are: - none - aBit
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), aBit(2), abcBit(3), abcdBit(4)

prtIn7p8VcPbxOos		1.3.6.1.4.1.164.3.2.3.2.15.3.1.8
Out of service Signaling mode.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	forcedIdle(1), forcedBusy(2)

prtIn7p8VcPbxLinkTo		1.3.6.1.4.1.164.3.2.3.2.15.3.1.9
This object indicates the slot of the ML card to which the VC card is mapped. In the ?004 Unit the entries io6(10)..io12(16) are not valid. For Server mode (prtIn7p8VcPbxMode=server), this object is not applicable. Both ports, 7 and 8 should be linked to the same Slot. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort.
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

prtExVcPbxTsTable		1.3.6.1.4.1.164.3.2.3.2.15.4
The write operation into the table objects is valid only to the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtExVcPbxTsEntry

prtExVcPbxTsEntry		1.3.6.1.4.1.164.3.2.3.2.15.4.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtExVcPbxTsEntry

prtExVcPbxTsCnfgIdx		1.3.6.1.4.1.164.3.2.3.2.15.4.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtExVcPbxTsSltIdx		1.3.6.1.4.1.164.3.2.3.2.15.4.1.2
This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

prtExVcPbxTsPrtIdx		1.3.6.1.4.1.164.3.2.3.2.15.4.1.3
This attribute indicates a unique port number. VCPBX/E1, VCPBX/T1, VFPBX/E1, VFPBX/T1, VF-24/T1 and VF-30 cards have only one external interface. VF-48/T1 and VF-60/E1 cards have two external interfaces. VFS cards have also internal ports.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	exPrt1(1), exPrt2(2), inPrt9(109), inPrt10(110)

prtExVcPbxTsIdx		1.3.6.1.4.1.164.3.2.3.2.15.4.1.4
This attribute indicates a unique PABX time slot position. The valid time slots are 1..24 for T1 cards and 1..31 for E1 cards.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtExVcPbxTsMode		1.3.6.1.4.1.164.3.2.3.2.15.4.1.5
This attribute indicates the usage, process and way of the specific PABX TS towards its destination: unused - the TS is not used (no processing, no destination). compressed - the TS is used, sent for compression to an internal port (for VF-PBX cards: 1..6 for of either the same card or a VF-PBX card of the same group). For VF-24/30/48/60 - 'compressed' represents 'compressed Voice' (to differentiate it from 'compressedCcs'). In this case, the TS is compressed by an internal port (1..8). transparent - the TS is used; no processing. It is sent directly for Bypass to a ML card the VF port/TS is linked to. compressedCcs - supported only by VF-24/30/48/60 cards. The TS is used; sent for compression to the CPU. mng - the TS is used for Management (this option is used when the external port is connected to another product that has to be managed via this dedicated TS. ccs1..ccs8 - supported only by VF-24/30/48/60 cards. Compressed TS that comes from a bundle of V5.1 or V5.2 PBX. ss7n1..ss7n8 - supported only by VF-24/30/48/60 cards. Compressed TS that comes from a bundle of V5.1 or V5.2 PBX. ss7n1 can work versus Vmux having prtExPh1MlTsType=ss7(6).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unused(1), compressed(2), transparent(3), compressedCcs(4), mng(5), ccs1(11), ccs2(12), ccs3(13), ccs4(14), ccs5(15), ccs6(16), ccs7(17), ccs8(18), ss7n1(41), ss7n2(42), ss7n3(43), ss7n4(44), ss7n5(45), ss7n6(46), ss7n7(47), ss7n8(48)

prtExVcPbxTsIConSlot		1.3.6.1.4.1.164.3.2.3.2.15.4.1.6
For VF-PBX cards, the io1..io12 values are applicable only when prtExVcPbxTsMode=compressed. Otherwise, its value should be noConnect. For VF-24/30/48/60 cards: - when prtExVcPbxTsMode=transparent or voiceTransparent, the io1..io12 values are applicable, indicating the ML Slot this TS is connected to. - when prtExVcPbxTsMode=compressed or compressedCcs, the value will be the same as prtExVcPbxTsSltIdx, since the compression is done within the same card. - for rest of the prtExVcPbxTsMode values, the value will be: noConnect. This object indicates whether the specified compressed/transparent time slot is connected/routed internally in the Agent and to which card it is connected. For VF-PBX card, the valid selectable slots are either the current one, (prtExVcPbxTsSltIdx), or a slot containing a VF-PBX card. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noConnect(2), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

prtExVcPbxTsIConPrt		1.3.6.1.4.1.164.3.2.3.2.15.4.1.7
This attribute indicates the port to which this TS is connected. For VF-PBX cards, only inPrt1..inPrt6 ports are valid. For VF-24/30/48/60 cards: - for prtExVcPbxTsMode=transparent or voiceTransparent, the valid ports are ML ports (exPrt1.. exPrt8, inPrt1.. inPrt8) - for prtExVcPbxTsMode=compressed or compressedCcs, the valid ports are internal ports of the same card (inPrt1..inPrt8) noConnect - when prtExVcPbxTsIConSlot=noConnect.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), exPrt5(5), exPrt6(6), exPrt7(7), exPrt8(8), noConnect(100), inPrt1(101), inPrt2(102), inPrt3(103), inPrt4(104), inPrt5(105), inPrt6(106), inPrt7(107), inPrt8(108)

prtExVcPbxTsIConTs		1.3.6.1.4.1.164.3.2.3.2.15.4.1.8
This attribute indicates the ML TS to which this TS is connected. This object is not applicable for VF-PBX cards. For VF-24/30/48/60 cards it is applicable only when prtExVcPbxTsMode=transparent or voiceTransparent. The valid time slots are 1..24 for ML T1 cards and 1..31 for ML E1 cards. notApplicable - 255.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..255

prtExVcPbxTsRemPrt		1.3.6.1.4.1.164.3.2.3.2.15.4.1.9
This attribute indicates the end-point port on the Remote unit. VF-24/T1 and VF-30/E1 cards have one external interface. VF-48/T1 and VF-60/E1 cards have two external interfaces. noConnect - when prtExVcPbxTsMode=unused, transparent, voiceTransparent or mng.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	exPrt1(1), exPrt2(2), noConnect(100)

prtExVcPbxTsRemTs		1.3.6.1.4.1.164.3.2.3.2.15.4.1.10
This attribute indicates the end-point TS on the Remote unit. The valid time slots are 1..24 for T1 ports and 1..31 for E1 ports. notApplicable - 255.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtExVcPbxTsRemConnID		1.3.6.1.4.1.164.3.2.3.2.15.4.1.11
This attribute indicates the Connection ID with the Remote unit. notApplicable = 0.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

prtExVcPbxTsSourceSlot		1.3.6.1.4.1.164.3.2.3.2.15.4.1.12
For VFS cards. These cards offer Compresed Voice Services for Analog Voice ports of the MP. This object indicates the Source Slot of the Analog Voice port we want to compress. io1..io12 values are applicable only when prtExVcPbxTsMode=compressed(voice). Otherwise, its value should be noConnect. In the ?004 Unit the entries io6(10)..io12(16) are not valid.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noConnect(2), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

prtExVcPbxTsSourcePrt		1.3.6.1.4.1.164.3.2.3.2.15.4.1.13
For VFS cards. These cards offer Compresed Voice Services for Analog Voice ports of the MP. This object indicates the Source Port within the Slot of the Analog Voice Card, we want to compress. exPrt1 - exPrt16 = 1 - 16 noConnect=100 - when prtExVcPbxTsCvServiceSlot=noConnect.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

prtIsdnCnfgTable		1.3.6.1.4.1.164.3.2.3.2.16.1
The write operation into the table objects is valid only to the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtIsdnCnfgEntry

prtIsdnCnfgEntry		1.3.6.1.4.1.164.3.2.3.2.16.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtIsdnCnfgEntry

prtIsdnCnfgIdx		1.3.6.1.4.1.164.3.2.3.2.16.1.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtIsdnSltIdx		1.3.6.1.4.1.164.3.2.3.2.16.1.1.2
This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid For KM2100/4 Valid entries are 'kmxMlA ' or 'kmxMlB'
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), kmxMlA(103), kmxMlB(104), notApplicable(255)

prtIsdnPrtIdx		1.3.6.1.4.1.164.3.2.3.2.16.1.1.3
This attribute indicates a unique port number. For MAXcess the values will be: exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), For KM-2100 the port index is calculated as follows: 100*Slot+Ch
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtIsdnConnect		1.3.6.1.4.1.164.3.2.3.2.16.1.1.4
This attribute indicates if the port is connected.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3)

prtIsdnSignalingProtocol		1.3.6.1.4.1.164.3.2.3.2.16.1.1.5
This attribute fixes which signaling protocol is used at this port (D-Channel). It is equivalent to isdnSignalingProtocol in the isdn MIB.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), etsi(3), ess4(5), ess5(6), dms100(7), ni1(9), ni2(10), ins64(17), ins1500(18), qsig(21), notApplicable(255)

prtIsdnBasicRateLineTopology		1.3.6.1.4.1.164.3.2.3.2.16.1.1.6
This attribute is relevant for ISDN BRI only. It is equivalent to isdnBasicRateLineTopology in the isdn MIB.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	pointToPoint(1), pointToMultipoint(2), notApplicable(255)

prtIsdnMode		1.3.6.1.4.1.164.3.2.3.2.16.1.1.7
This attribute allows the user to configure the port as leased(2) in case of connection to a TDM network.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	dialup(1), leased(2), syncLeased(3), notApplicable(255)

prtIsdnFilter		1.3.6.1.4.1.164.3.2.3.2.16.1.1.8
This attribute allows the user to configure the port: answerAll(2): accept all incoming calls, rejectAll(3): reject all incoming calls, selective(4): accept or reject according directory table. callBack (5): In this mode the ISDN Ch will reject incoming calls and will initiate call back to the rejected phone number.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), answerAll(2), rejectAll(3), selective(4), callBack(5)

prtIsdnSimultaneousCall		1.3.6.1.4.1.164.3.2.3.2.16.1.1.9
In case of simultaneous call (local,remote and remote,local): accept(2): accept the incoming call, reject(3): reject the incoming call.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), accept(2), reject(3)

prtIsdnNumOfAbstractTerm		1.3.6.1.4.1.164.3.2.3.2.16.1.1.10
An object for KM2100/4 agents. 255=Not Applicable When ISDN Standard = ETSI or NTT (European) the value should be 255 (NotApplicable) else If ML speed is 64Kbps value should be 1. If ML speed is 128Kbps value can be either 1 or 2 (user selection).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtIsdnSwitchMode		1.3.6.1.4.1.164.3.2.3.2.16.1.1.11
For KM2100. auto - The call is initiated automatically by one of the IO cards connected to KML.10(ISDN card) having ISDN Switch Mode. manual - The call is initiated by the user manually, for KML.10 having ISDN Switch Mode (via mdlSCmd). connect- The call is initiated 'immediately', for KML.10 having ISDN Switch Mode. 'immediately'- means: immediately after power-up (when product performed Reset) OR, since this value appears in the active configuration. In this case, the call can be disconnected only by power-off of the product or by changing this object to another value (or actual Remove of the KML.10 relevant card). notApplicable - For other card types.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), auto(2), manual(3), connect(4)

prtIsdnAbSide		1.3.6.1.4.1.164.3.2.3.2.16.1.1.12
This parameter indicates the QSIG side in layer 3. This definition is from the QSIG Standard.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), aSide(2), bSide(3)

prtIsdnQsigRole		1.3.6.1.4.1.164.3.2.3.2.16.1.1.13
This parameter indicates the QSIG side in layer 1 & 2.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), slave(2), master(3)

prtIsdnInterface		1.3.6.1.4.1.164.3.2.3.2.16.1.1.14
It indicates the interface type: lt = line termination nt = network termination te = terminal equipment.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	lt(1), nt(2), te(3), notApplicable(255)

prtIsdnCallMode		1.3.6.1.4.1.164.3.2.3.2.16.1.1.15
This object indicates the acceptance of incoming calls. Initiate - Callout Listen - Callin.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), initiate(2), listen(3)

prtIsdnCallBackTimeout		1.3.6.1.4.1.164.3.2.3.2.16.1.1.16
This object is applicable only if 'prtIsdnFilter' is 'CallBack' and determines how long to wait from receiving the incoming call until initiating the call back call. The vaules range should be '1..20 sec' and the default 10 sec.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtIsdnEndpointTable		1.3.6.1.4.1.164.3.2.3.2.16.2
The write operation into the table objects is valid only to the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtIsdnEndpointEntry

prtIsdnEndpointEntry		1.3.6.1.4.1.164.3.2.3.2.16.2.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtIsdnEndpointEntry

prtIsdnEndpointCnfgIdx		1.3.6.1.4.1.164.3.2.3.2.16.2.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtIsdnEndpointSltIdx		1.3.6.1.4.1.164.3.2.3.2.16.2.1.2
This attribute indicates a unique slot position where the card is inserted. In ?004 Unit the entries io6(10)..io12(16) are not valid For KM2100/4 Valid entries are 'kmxMlA ' or 'kmxMlB'
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), kmxMlA(103), kmxMlB(104), notApplicable(255)

prtIsdnEndpointPrtIdx		1.3.6.1.4.1.164.3.2.3.2.16.2.1.3
This attribute indicates a unique port number. For MAXcess the values will be: exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), For KM-2100 the port index is calculated as follows: 100*Slot+Ch
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtIsdnEndpointIdx		1.3.6.1.4.1.164.3.2.3.2.16.2.1.4
Since more than one endpoint may be defined per isdn entity, this field is a simple index. It corresponds to isdnEndpointIdx in the isdn MIB.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	atei1(1), atei2(2)

prtIsdnEndpointTeiType		1.3.6.1.4.1.164.3.2.3.2.16.2.1.5
The type of TEI (Terminal Endpoint Identifier) used for this Terminal Endpoint. In case of dynamic(1), the TEI value is selected by the switch. In case of static(2), a valid TEI value has to be entered in the isdnEndpointTeiValue object. interface type as well as the Terminal Endpoint type. static(2). On Basic Rate interfaces the default value is dynamic(1) for isdn(63) Terminal Endpoints. It corresponds to isdnEndpointTeiType in the isdn MIB.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	dynamic(1), static(2), notApplicable(255)

prtIsdnEndpointTeiValue		1.3.6.1.4.1.164.3.2.3.2.16.2.1.6
When the TEI Type is static, the value of the TEI should be between 0 and 63. Else, it is not selectable by user. 255 = notApplicable. It corresponds to isdnEndpointTeiValue in the isdn MIB
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

prtIsdnEndpointSpid		1.3.6.1.4.1.164.3.2.3.2.16.2.1.7
The Service profile IDentifier (SPID) information for this Terminal Endpoint. It is is composed of 9-20 numeric characters. It corresponds to isdnEndpointSpid in the isdn MIB.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString

prtIsdnEndpointBearerCh		1.3.6.1.4.1.164.3.2.3.2.16.2.1.8
This is the selected dialing channel. anyChannel - the system selects the dialing channel.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notApplicable(1), anyChannel(2), channelB1(3), channelB2(4)

prtIsdnEndpointRowStatus		1.3.6.1.4.1.164.3.2.3.2.16.2.1.9
This field indicates whether to consider this endpoint or not. The only possible supported RowStatus vaules are active (1) and destroy (6).
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

prtIsdnDirectoryTable		1.3.6.1.4.1.164.3.2.3.2.16.3
The write operation into the table objects is valid only to the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtIsdnDirectoryEntry

prtIsdnDirectoryEntry		1.3.6.1.4.1.164.3.2.3.2.16.3.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtIsdnDirectoryEntry

prtIsdnDirectoryCnfgIdx		1.3.6.1.4.1.164.3.2.3.2.16.3.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtIsdnDirectorySltIdx		1.3.6.1.4.1.164.3.2.3.2.16.3.1.2
This attribute indicates a unique slot position where the card is inserted. For MX300/30 ports: io1(5) = isdn1(5) and io2(6) = isdn2(6). In ?004 Unit the entries io6(10)..io12(16) are not valid For KM2100/4 Valid entries are 'kmxMlA ' or 'kmxMlB'
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), kmxMlA(103), kmxMlB(104), notApplicable(255)

prtIsdnDirectoryPrtIdx		1.3.6.1.4.1.164.3.2.3.2.16.3.1.3
For MAXcess this is the internal port number: 101, 102,.... For KM-2100 the port index is calculated as follows: 100*Slot+Ch
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtIsdnDirectoryLocalAddr		1.3.6.1.4.1.164.3.2.3.2.16.3.1.4
This is the local address associated with this entry. - For MX: Size=17 , Default=0 (17 characters) - For KM: Size=20, Default=blank (20 characters)
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(17..20)

prtIsdnDirectoryLocalSubAddr		1.3.6.1.4.1.164.3.2.3.2.16.3.1.5
This is the local subaddress associated with this entry. - For MX: Size=6 , Default=0 (6 characters) - For KM: Size=4 , Default=blank (4 characters)
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(4..6)

prtIsdnDirectoryRemoteAddr		1.3.6.1.4.1.164.3.2.3.2.16.3.1.6
This is the remote address associated with this entry. - For MX: Size=17 , Default=0 (17 characters) - For KM: Size=20, Default=blank (20 characters)
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(17..20)

prtIsdnDirectoryRemoteSubAddr		1.3.6.1.4.1.164.3.2.3.2.16.3.1.7
This is the remote subaddress associated with this entry. - For MX: Size=6 , Default=0 (6 characters) - For KM: Size=4 , Default=blank (4 characters)
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(4..6)

prtIsdnDirectoryPrtNu		1.3.6.1.4.1.164.3.2.3.2.16.3.1.8
This is the external port number connected to this entry.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

prtIsdnDirectoryTeiId		1.3.6.1.4.1.164.3.2.3.2.16.3.1.9
This is the abstract terminal id if relevant, connected to this entry.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

prtIsdnDirectoryRowStatus		1.3.6.1.4.1.164.3.2.3.2.16.3.1.10
This is the status for the row. It allows to know whether to consider this row or not. The only possible supported RowStatus vaules are active (1) and destroy (6).
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

prtIsdnDirectoryLocalAddr2		1.3.6.1.4.1.164.3.2.3.2.16.3.1.11
This is the second local address associated with this entry. - For MX: Size=17 , Default=0 (17 characters) - For KM: Size=20, Default=blank (20 characters)
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(17..20)

prtIsdnDirectoryLocalSubAddr2		1.3.6.1.4.1.164.3.2.3.2.16.3.1.12
This is the second local subaddress associated with this entry. - For MX: Size=6 , Default=0 (6 characters) - For KM: Size=4 , Default=blank (4 characters)
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(4..6)

prtIsdnDirectoryRemoteAddr2		1.3.6.1.4.1.164.3.2.3.2.16.3.1.13
This is the second remote address associated with this entry. - For MX: Size=17 , Default=0 (17 characters) - For KM: Size=20, Default=blank(20 characters)
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(17..20)

prtIsdnDirectoryRemoteSubAddr2		1.3.6.1.4.1.164.3.2.3.2.16.3.1.14
This is the second remote subaddress associated with this entry. - For MX: Size=6 , Default=0 (6 characters) - For KM: Size=4 , Default=blank (4 characters)
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(4..6)

prtFrPlusCnfgTable		1.3.6.1.4.1.164.3.2.3.2.18.1
The write operation into the Table Objects is valid only to the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtFrPlusCnfgEntry

prtFrPlusCnfgEntry		1.3.6.1.4.1.164.3.2.3.2.18.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtFrPlusCnfgEntry

prtFrPlusCnfgIdx		1.3.6.1.4.1.164.3.2.3.2.18.1.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtFrPlusSltIdx		1.3.6.1.4.1.164.3.2.3.2.18.1.1.2
Slot Index. For ISDN BRI Ports of MX300/30, io1(5) = isdn1(5) and io2(6) = isdn2(6).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

prtFrPlusPrtIdx		1.3.6.1.4.1.164.3.2.3.2.18.1.1.3
This attribute indicates a unique port number. This port number should be: - for ISDN cards: inPrt1(101)->inPrt50(150) - for MHS1 card : exPrt1(1) - for MHS3, MLS3 cards: exPrt1(1)->exPrt3(3) - for MLS6 cards: exPrt1(1)->exPrt6(6).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtFrPlusNotSegmentedPriorities		1.3.6.1.4.1.164.3.2.3.2.18.1.1.4
This parameter is relevant only for FR+ protocol and asks the MXcess NOT to segment data with specified priorities: from LSB: bit 1 is for priority 1, bit 2 is for priority 2, .... till bit 7 for priority 7. - a priority selected to be segmented : its bit will be '0' - a priority not to be segmented : its bit will be '1' Default is 00000000; i.e, segment all priorities.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(1)

prtMl4CnfgTable		1.3.6.1.4.1.164.3.2.3.2.19.1
This is an extension table for MTML-4 card parameters.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtMl4CnfgEntry

prtMl4CnfgEntry		1.3.6.1.4.1.164.3.2.3.2.19.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtMl4CnfgEntry

prtMl4CnfgIdx		1.3.6.1.4.1.164.3.2.3.2.19.1.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. The write operation is valid only to the TmpCnfg.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtMl4SltIdx		1.3.6.1.4.1.164.3.2.3.2.19.1.1.2
This attribute indicates a unique slot position where the module is inserted.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

prtMl4PrtIdx		1.3.6.1.4.1.164.3.2.3.2.19.1.1.3
This attribute indicates a unique port number.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), exPrt5(5), exPrt6(6), exPrt7(7), exPrt8(8), inPrt1(101), inPrt2(102), inPrt3(103), inPrt4(104), inPrt5(105), inPrt6(106), inPrt7(107), inPrt8(108), inPrt9(109), inPrt10(110), inPrt11(111), inPrt12(112), inPrt13(113), inPrt14(114), inPrt15(115), inPrt16(116), inPrt17(117), inPrt18(118), inPrt19(119), inPrt20(120), inPrt21(121), inPrt22(122), inPrt23(123), inPrt24(124), inPrt25(125), inPrt26(126), inPrt27(127), inPrt28(128), inPrt29(129), inPrt30(130), inPrt31(131), inPrt32(132), inPrt33(133), inPrt34(134), inPrt35(135), inPrt36(136), inPrt37(137), inPrt38(138), inPrt39(139), inPrt40(140), inPrt41(141), inPrt42(142), inPrt43(143), inPrt44(144), inPrt45(145), inPrt46(146), inPrt47(147), inPrt48(148), inPrt49(149), inPrt50(150), inPrt51(151), inPrt52(152), inPrt53(153), inPrt54(154), inPrt55(155), inPrt56(156), inPrt57(157), inPrt58(158), inPrt59(159), inPrt60(160), inPrt61(161), inPrt62(162), inPrt63(163), inPrt64(164), inPrt65(165), inPrt66(166), inPrt67(167), inPrt68(168), inPrt69(169), inPrt70(170), inPrt71(171), inPrt72(172), inPrt73(173), inPrt74(174), inPrt75(175), inPrt76(176), inPrt77(177), inPrt78(178), inPrt79(179), inPrt80(180), inPrt81(181), inPrt82(182), inPrt83(183), inPrt84(184)

prtMl4SigProfile		1.3.6.1.4.1.164.3.2.3.2.19.1.1.4
This object indicates the Signaling Profile of the port. none - when the Frame is G732N (no MF) or Unframed. p1 = profile 1 p2 = profile 2 p3 = profile 3 p4 = profile 4 p5 = profile 5 perTS = when Signaling Profile is selected per TS.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), none(2), p1(3), p2(4), p3(5), p4(6), p5(7), perTS(8)

prtMl4CGA		1.3.6.1.4.1.164.3.2.3.2.19.1.1.5
This object selects the method used to signal the CGA state to the other end, through the main link. 'none' - non-transparent mode. When one of the links (main) will be in Out Of Service state, both 'Data/Voice Oos' and 'Oos' will be transmitted to the other end. 'trans' - when one of the links (main) will be in Out Of Service state, 'Data/Voice Oos' will be transmitted to the other end. 'full' - fully-transparent mode. When one of the links (main) will be in Out Of Service state, neither 'Data/Voice Oos' nor 'Oos' will be transmitted to the other end.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), trans(2), full(3)

prtMl4Oos		1.3.6.1.4.1.164.3.2.3.2.19.1.1.6
'idle' = '0' = on-hook, idle state 'busy' = '1' = off-hook, busy state 'forcedIdle' = SP = both A and B signaling bits are forced to '0' during out-of-service periods. 'forcedBusy' = MK = both A and B signaling bits are forced to '1' during out-of-service periods. 'busyIdle' = MK_SP = A and B bits are forced to '1' for 2.5 seconds; then they are switched to '0' until out-of-service condition disappears. 'idleBusy' = SP_MK = A and B bits are forced to '0' for 2.5 seconds; then they are switched to '1' until out-of-service condition disappears. - for T1: '0'=0 ; '1'=1 - for E1: '0'=1 ; '1'=0
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notSupported(2), forcedIdle(3), forcedBusy(4), busyIdle(5), idleBusy(6)

prtMl4VoiceOos		1.3.6.1.4.1.164.3.2.3.2.19.1.1.7
Voice Out-Of-Service code. Valid range: (0 - FF HEX). For agents that do not support this feature, the value will always be 0.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..4)

prtMl4DataOos		1.3.6.1.4.1.164.3.2.3.2.19.1.1.8
Data Out-Of-Service code. Valid range: (0 - FF HEX). For agents that do not support this feature, the value will always be 0.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..4)

prtMl4Service		1.3.6.1.4.1.164.3.2.3.2.19.1.1.9
Link Service. leasedLine - usual TDM interface. v51 - V5.1 interface. v52Master - V5.2 Link to Local Exchange. v52Slave - a ML that is transferred to the v52Master.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), leasedLine(2), v51(3), v52Master(4), v52Slave(5)

prtMl4IpAddress		1.3.6.1.4.1.164.3.2.3.2.19.1.1.10
IP Address of the port.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

prtMl4IpMask		1.3.6.1.4.1.164.3.2.3.2.19.1.1.11
IP subnet mask of the port.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

prtMl4SignalingMode		1.3.6.1.4.1.164.3.2.3.2.19.1.1.12
Refers to the signaling mode of the port (or framer module). notApplicable(1)- means that no framer is needed for this port (no signaling), or that this object is not relevant. cas(2) means Channel Associated Signaling. Used for E1 Links. ccs(3) is the Common Channel Signaling (the signaling is not within the channels time slot - a TS for signaling is used). robbedBit(4) is a method implementing 7 bits for the voice and 1 bit dedicated for signaling. Used for T1 Links. other (5)- Signaling generally exists though not specifically according to one of the values listed ; this port uses a framer in this case.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), cas(2), ccs(3), robbedBit(4), other(5)

prtMl4EchoCanceler		1.3.6.1.4.1.164.3.2.3.2.19.1.1.13
Echo canceler activation.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), off(2), on(3)

prtMl4OosErrorSource		1.3.6.1.4.1.164.3.2.3.2.19.1.1.14
OOS (Out-of-Service) Error Source. This object is applicable for T1 ports only.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), none(2), framing(3), bpv(4)

prtMl4OosEntryThreshold		1.3.6.1.4.1.164.3.2.3.2.19.1.1.15
This object defines the number of Errors per Second that determine the minimum unacceptable noise level. This value will be the Entry Threshold to the OOS (Out-of-Service) state. This object is applicable only when prtMl4OosErrorSource=framing(3) or bpv(4). 0=notApplicable.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..999

prtMl4OosExitThreshold		1.3.6.1.4.1.164.3.2.3.2.19.1.1.16
This object defines the number of consecutive Error-Free-Seconds before going from OOS state to Normal state. This value will be the Exit Threshold from the OOS (Out-of-Service) state. Units=seconds This object is applicable only when prtMl4OosErrorSource=framing(3) or bpv(4). 0=notApplicable.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..99

prtMl4LogicalLinkId		1.3.6.1.4.1.164.3.2.3.2.19.1.1.17
This object defines for a V5.2 Master ML the Logical Link Id. Valid values are: 0..256. NA=257.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..257

prtMl4DedicatedTs		1.3.6.1.4.1.164.3.2.3.2.19.1.1.18
A unique number to identify Dedicated TS of the E1 port (V5.2). It is applicable only when prtMl4Service=v52Slave and prtExPh1MlInbandMng selected is dedicatedTs, dedicatedPpp or dedicatedFr. 1..31 - Dedicated TS of E1 255 - notApplicable Other values are invalid.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..255

prtMl4RemCrc		1.3.6.1.4.1.164.3.2.3.2.19.1.1.19
This object indicates whether the E1 of the Remote device connected to this E1 port, will have CRC-4 or not.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), no(2), yes(3)

prtMl4CrossConnectLevel		1.3.6.1.4.1.164.3.2.3.2.19.1.1.20
This object indicates whether the cross connect is on DS1 or DS0 (time-slots) level. When cross connect level is ds1, Destination Slot is indicated by prtGenCnfgLinkToSlot, Destination Port is indicated by prtGenCnfgLinkToPort. For Unframed Line Type, cross connect level can be either notApplicable (NC=not connected) or DS1. Otherwise, default value is ds0.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), ds0(2), ds1(3)

prtMl4PppEchoFailDetection		1.3.6.1.4.1.164.3.2.3.2.19.1.1.21
This object indicates whether the PPP Echo is taken into account for its Fail Detection. This object is relevant when Inband Mng between devices is Dedicated TS PPP. Default=Disable. Enable - will be selected mainly when a T1/E1 Ring exists and between 2 adjacent Ring devices there is another device or Net, that causes these Ring devices not to sense that the PPP connection between them is lost. In this case, Echo Request should be initiated by the port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), enable(3)

prtAcmCnfgTable		1.3.6.1.4.1.164.3.2.3.2.20.1
This is a table for ACM port parameters.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtAcmCnfgEntry

prtAcmCnfgEntry		1.3.6.1.4.1.164.3.2.3.2.20.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtAcmCnfgEntry

prtAcmCnfgIdx		1.3.6.1.4.1.164.3.2.3.2.20.1.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. The write operation is valid only to the TmpCnfg.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtAcmSltIdx		1.3.6.1.4.1.164.3.2.3.2.20.1.1.2
This attribute indicates a unique slot position where the module is inserted.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255)

prtAcmPrtIdx		1.3.6.1.4.1.164.3.2.3.2.20.1.1.3
This attribute indicates a unique port number.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), exPrt5(5), exPrt6(6), exPrt7(7), exPrt8(8), exPrt9(9), exPrt10(10), exPrt11(11), exPrt12(12)

prtAcmConnect		1.3.6.1.4.1.164.3.2.3.2.20.1.1.4
This attribute indicates whether the port should be connected or not. Only a connected port can perform activity.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3)

prtAcmActiveState		1.3.6.1.4.1.164.3.2.3.2.20.1.1.5
This attribute indicates the Electric Active State of the port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	low(2), high(3)

prtAcmAlrString		1.3.6.1.4.1.164.3.2.3.2.20.1.1.6
Alarm string selected by user for the Inbound ports. This object is applicable only for the Inbound Ports: ext-5..ext-12. For the Outbound Ports (ext-1..ext-4), the size of this string will be 0.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..35)

prtE2CnfgTable		1.3.6.1.4.1.164.3.2.3.2.21.1
This is a table for E2 port parameters.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtE2CnfgEntry

prtE2CnfgEntry		1.3.6.1.4.1.164.3.2.3.2.21.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtE2CnfgEntry

prtE2CnfgIdx		1.3.6.1.4.1.164.3.2.3.2.21.1.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. The write operation is valid only to the TmpCnfg.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtE2SltIdx		1.3.6.1.4.1.164.3.2.3.2.21.1.1.2
This attribute indicates a unique slot position where the module is inserted.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

prtE2PrtIdx		1.3.6.1.4.1.164.3.2.3.2.21.1.1.3
This attribute indicates a unique port number.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	exPrt1(1), exPrt2(2)

prtE2Connect		1.3.6.1.4.1.164.3.2.3.2.21.1.1.4
This attribute indicates whether the port should be connected or not. Only a connected port can perform activity.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3)

prtE2MngOnNationalBit		1.3.6.1.4.1.164.3.2.3.2.21.1.1.5
This attribute indicates whether National Bit will be used for Management or not.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3)

prtLanWanCnfgTable		1.3.6.1.4.1.164.3.2.3.2.22.1
This is a table for Lan-Wan port parameters.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtLanWanCnfgEntry

prtLanWanCnfgEntry		1.3.6.1.4.1.164.3.2.3.2.22.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtLanWanCnfgEntry

prtLanWanCnfgIdx		1.3.6.1.4.1.164.3.2.3.2.22.1.1.1
This object indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. The write operation is valid only to the TmpCnfg.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..255

prtLanWanSltIdx		1.3.6.1.4.1.164.3.2.3.2.22.1.1.2
This object indicates a unique slot position where the module is inserted.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	notApplicable(1), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16)

prtLanWanPrtIdx		1.3.6.1.4.1.164.3.2.3.2.22.1.1.3
This object indicates a unique number to identify a port in a specific card. Generally, for MP-210X/2200, the Port Index will be according to the external/internal port number: - exPrtX : X - inPrtX : 100 + X For FCD-155, refer to device specification
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

prtLanWanMode		1.3.6.1.4.1.164.3.2.3.2.22.1.1.4
This object determines the working mode of this port. For FCD155, layer3SubnetSwitch is not applicable
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), bridge(2), bridgeAndStp(3), layer3SubnetSwitch(4)

prtLanWanDestIf		1.3.6.1.4.1.164.3.2.3.2.22.1.1.5
This object determines the Destination Interface for the frames received by this port. - Switching Table = 100 (it means that the destination interface will be determined by the Switching Table) - inPrtX (internal-X port): 100 + X . For FCD-155 this object is not applicable =0
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtLanWanEgressVlanMode		1.3.6.1.4.1.164.3.2.3.2.22.1.1.6
This object determines what to do with the VLAN frames that exit via the WAN side of the port. This object is not applicable when prtLanWanMode=l3SubnetSwitch(4).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), unmodified(2), tag(3), doubleTag(4), untag(5)

prtLanWanL2Protocol		1.3.6.1.4.1.164.3.2.3.2.22.1.1.7
L2 Protocol. When prtLanWanMode=l3SubnetSwitch(4), the only valid value is ppp(3).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), none(2), ppp(3), hdlc(4), pppoHdlc(5), mlppp(6)

prtLanWanStpPriority		1.3.6.1.4.1.164.3.2.3.2.22.1.1.8
The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..255

prtLanWanStpCost		1.3.6.1.4.1.164.3.2.3.2.22.1.1.9
The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1990 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..65535

prtLanWanToLanVlanMode		1.3.6.1.4.1.164.3.2.3.2.22.1.1.10
This object determines what to do with the VLAN frames that come from WAN side of the port and exit towards one of the LAN ports. This object is applicable only when prtLanWanDestIf=100 or 101 (Switching Table or inPrt1).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), unmodified(2), tag(3), doubleTag(4), untag(5)

prtLanWanVlanId		1.3.6.1.4.1.164.3.2.3.2.22.1.1.11
This is the VLAN Id attached to a frame, when the relevant Vlan Mode (prtLanWanEgressVlanMode or prtLanWanToLanVlanMode) is tag or doubleTag. 0=not applicable.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..4095

prtLanWanVlanPriority		1.3.6.1.4.1.164.3.2.3.2.22.1.1.12
This is the VLAN Priority attached to a frame, when the relevant Vlan Mode (prtLanWanEgressVlanMode or prtLanWanToLanVlanMode) is tag or doubleTag. Valid values: 0..7 255=not applicable.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtLanWanMtu		1.3.6.1.4.1.164.3.2.3.2.22.1.1.13
The size of the largest packet which can be sent/received on the interface, specified in octets. Valid values change per device. 0=not applicable.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtLanWanVlanType		1.3.6.1.4.1.164.3.2.3.2.22.1.1.14
This oject indicates type of VLAN this port is assigned to. Port Base Vlan parameters are defined by objects under radBridgePortBaseVlan
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), portBasedVlan(2), ieee802dot1q(3), ieee802dot1qTaggedOnly(4)

muxHubEvents		1.3.6.1.4.1.164.3.2.0
The events for .
Status: current	Access: read-write
OBJECT-IDENTITY

alarmsTrap		1.3.6.1.4.1.164.3.2.0.1
This trap is sent whenever alarm occurs in the agent.
Status: current	Access: read-write
NOTIFICATION-TYPE

sanityTrap		1.3.6.1.4.1.164.3.2.0.2
This trap is sent after a data base update. It returns the sanity result status and the configuration no. checked. If the result is of Flip DB Sanity Check, the configuration no. sent will be 0. If the result is of Variant Sanity Check, the configuration no. sent will be 100.
Status: current	Access: read-write
NOTIFICATION-TYPE

cnfgFlipTrap		1.3.6.1.4.1.164.3.2.0.3
This trap is sent upon change of the active Configuration DB. Attached, is the new active Configuration no.
Status: current	Access: read-write
NOTIFICATION-TYPE

flipDbChangeTrap		1.3.6.1.4.1.164.3.2.0.4
This trap is sent upon change of the active Flip tables (Flip DB).
Status: current	Access: read-write
NOTIFICATION-TYPE

statusChangedTrap		1.3.6.1.4.1.164.3.2.0.5
This trap is sent upon any change of the LEDs status.
Status: current	Access: read-write
NOTIFICATION-TYPE

ds1Interface		1.3.6.1.4.1.164.3.1.6.4
OBJECT IDENTIFIER

prtDS1Events		1.3.6.1.4.1.164.3.1.6.4.0
OBJECT IDENTIFIER

prtDs1PerfHistory		1.3.6.1.4.1.164.3.1.6.4.1
OBJECT IDENTIFIER

dsx1XCurrentTable		1.3.6.1.4.1.164.3.1.6.4.1.2
A list of current statistics entries. This table contains additional objects for the current table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Dsx1XCurrentEntry

dsx1XCurrentEntry		1.3.6.1.4.1.164.3.1.6.4.1.2.1
An entry containing additional statistical counters applicable to a particular current table.
Status: current	Access: not-accessible
OBJECT-TYPE
	Dsx1XCurrentEntry

dsx1CurrentLOS		1.3.6.1.4.1.164.3.1.6.4.1.2.1.1
The counter associated with the number of LOS seconds, encountered by a DS1 interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCurrentCount

dsx1CurrentLOF		1.3.6.1.4.1.164.3.1.6.4.1.2.1.2
The counter associated with the number of LOF seconds, encountered by a DS1 interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCurrentCount

dsx1CurrentLOC		1.3.6.1.4.1.164.3.1.6.4.1.2.1.3
Loss Of Cell delineation. Counts number of cells the ATM UNI cells receiver lost cells delineation .
Status: current	Access: read-only
OBJECT-TYPE
	PerfCurrentCount

dsx1CurrentAIS		1.3.6.1.4.1.164.3.1.6.4.1.2.1.4
The counter associated with the number of AIS seconds, encountered by a DS1 interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCurrentCount

dsx1CurrentRAI		1.3.6.1.4.1.164.3.1.6.4.1.2.1.5
Remote Alarm Indication: Transmitted in the outgoing direction (toward the PABX) over FDL bits when the DS1 device detected an incoming Loss Of Frame. Received from the far end (PABX) over FDL when it detects a Loss of frame.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCurrentCount

dsx1CurrentLOMF		1.3.6.1.4.1.164.3.1.6.4.1.2.1.6
Loss of Multi-Frame sequence in E1 time slot 16.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCurrentCount

dsx1CurrentFEBE		1.3.6.1.4.1.164.3.1.6.4.1.2.1.7
Far End Block Errors, as reported in the first bit of frames 13 and 15, on multiframe E1 lines with CRC4, in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCurrentCount

dsx1CurrentStatus		1.3.6.1.4.1.164.3.1.6.4.1.2.1.8
The statuses of the current interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was partialy out. 4 - notValid - module is out.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(4)

dsx1CurrentBPV		1.3.6.1.4.1.164.3.1.6.4.1.2.1.9
The counter associated with the number of BPVs (Bi-Polar Violations) encountered by a DS1 interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCurrentCount

dsx1CurrentLOCRCMF		1.3.6.1.4.1.164.3.1.6.4.1.2.1.10
Loss of CRC4 Multi-Frame sequence in E1. encountered in the current 15 minute interval
Status: current	Access: read-only
OBJECT-TYPE
	PerfCurrentCount

dsx1CurrentLOFC		1.3.6.1.4.1.164.3.1.6.4.1.2.1.11
Counts the number of loss of frame events measured. encountered in the current 15 minute interval
Status: current	Access: read-only
OBJECT-TYPE
	PerfCurrentCount

dsx1CurrentCRCErrors		1.3.6.1.4.1.164.3.1.6.4.1.2.1.12
Counts the number of CRC error events, encountered in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCurrentCount

dsx1XIntervalTable		1.3.6.1.4.1.164.3.1.6.4.1.3
A list of Interval entries. This table contains additional objects for the interval table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Dsx1XIntervalEntry

dsx1XIntervalEntry		1.3.6.1.4.1.164.3.1.6.4.1.3.1
An entry containing additional statistical counters applicable to a particular interval table.
Status: current	Access: not-accessible
OBJECT-TYPE
	Dsx1XIntervalEntry

dsx1IntervalLOS		1.3.6.1.4.1.164.3.1.6.4.1.3.1.1
The counter associated with the number of LOS seconds , encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	PerfIntervalCount

dsx1IntervalLOF		1.3.6.1.4.1.164.3.1.6.4.1.3.1.2
The counter associated with the number of OOF seconds, encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	PerfIntervalCount

dsx1IntervalLOC		1.3.6.1.4.1.164.3.1.6.4.1.3.1.3
Loss Of Cell delineation. Counts number of cells the ATM UNI cells receiver lost cells delineation .
Status: current	Access: read-only
OBJECT-TYPE
	PerfIntervalCount

dsx1IntervalAIS		1.3.6.1.4.1.164.3.1.6.4.1.3.1.4
The counter associated with the number of AIS seconds, encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	PerfIntervalCount

dsx1IntervalRAI		1.3.6.1.4.1.164.3.1.6.4.1.3.1.5
Remote Alarm Indication: Transmitted in the outgoing direction (toward the PABX) over FDL bits when the DS1 device detected an incoming Loss Of Frame. Received from the far end (PABX) over FDL when it detects a Loss of frame.
Status: current	Access: read-only
OBJECT-TYPE
	PerfIntervalCount

dsx1IntervalLOMF		1.3.6.1.4.1.164.3.1.6.4.1.3.1.6
Loss of Multi-Frame sequence in E1 time slot 16.
Status: current	Access: read-only
OBJECT-TYPE
	PerfIntervalCount

dsx1IntervalFEBE		1.3.6.1.4.1.164.3.1.6.4.1.3.1.7
Far End Block Errors, as reported in the first bit of frames 13 and 15, on multiframe E1 lines with CRC4, in one of the previous 96, individual, 15 minute intervals.
Status: current	Access: read-only
OBJECT-TYPE
	PerfIntervalCount

dsx1IntervalStatus		1.3.6.1.4.1.164.3.1.6.4.1.3.1.8
The statuses of the current interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was partialy out. 4 - notValid - module is out.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(4)

dsx1IntervalBPV		1.3.6.1.4.1.164.3.1.6.4.1.3.1.9
The counter associated with the number of BPV (Bi-Polar Violations) encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	PerfIntervalCount

dsx1IntervalLOCRCMF		1.3.6.1.4.1.164.3.1.6.4.1.3.1.10
Loss of CRC4 Multi-Frame sequence in E1.
Status: current	Access: read-only
OBJECT-TYPE
	PerfIntervalCount

dsx1IntervalLOFC		1.3.6.1.4.1.164.3.1.6.4.1.3.1.11
Counts the number of loss of frame events measured in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	PerfIntervalCount

dsx1XTotalTable		1.3.6.1.4.1.164.3.1.6.4.1.4
A list of Total statistics entries. This table contains additional objects for the Total table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Dsx1XTotalEntry

dsx1XTotalEntry		1.3.6.1.4.1.164.3.1.6.4.1.4.1
An entry containing additional statistical counters applicable to a particular current table.
Status: current	Access: not-accessible
OBJECT-TYPE
	Dsx1XTotalEntry

dsx1TotalLOS		1.3.6.1.4.1.164.3.1.6.4.1.4.1.1
The counter associated with the number of LOS (Loss of Signal) seconds encountered by a DS1 interface in the previous 24 hour interval. Invalid 15 minute intervals count as 0.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

dsx1TotalBPV		1.3.6.1.4.1.164.3.1.6.4.1.4.1.9
The counter associated with the number of BPV (Bi-Polar Violations) encountered by a DS1 interface in the previous 24 hour interval. Invalid 15 minute intervals count as 0.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

dsx1TotalLOFC		1.3.6.1.4.1.164.3.1.6.4.1.4.1.11
The counter associated with the number loss of frames encountered by a DS1 interface in the previous 24 hour interval. Invalid 15 minute intervals count as 0.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

dsx1DataStreamStatTable		1.3.6.1.4.1.164.3.1.6.4.1.5
The DS1 Data Stream Statistics table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Dsx1DataStreamStatEntry

dsx1DataStreamStatEntry		1.3.6.1.4.1.164.3.1.6.4.1.5.1
An entry in the DS1 Data Stream Statistics table.
Status: current	Access: not-accessible
OBJECT-TYPE
	Dsx1DataStreamStatEntry

dsx1DataStreamStatIfIndex		1.3.6.1.4.1.164.3.1.6.4.1.5.1.1
The index of the DS1 interface. It may be ifIndex.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

dsx1DataStreamStatIndex		1.3.6.1.4.1.164.3.1.6.4.1.5.1.2
The DS1 Data Stream Index. For Vmux - the following indices are used: 1 for Transparent 2-3 for SS71-SS72 (respectively) 4-7 for Data1-Data4 (respectively) 8 for HDLC Ph2 Compatible 9-16 for Sub-CH1-1...Sub-CH1-8 (respectively).
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

dsx1DataStreamStatValid		1.3.6.1.4.1.164.3.1.6.4.1.5.1.3
Indicates whether this Data Stream is valid or not. When invalid - all counters are irrelevant.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

dsx1DataStreamStatInFrames		1.3.6.1.4.1.164.3.1.6.4.1.5.1.4
The counter associated with the number of received frames, encountered by the DS1 Data Stream.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

dsx1DataStreamStatInBytes		1.3.6.1.4.1.164.3.1.6.4.1.5.1.5
The counter associated with the number of received bytes, encountered by the DS1 Data Stream.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

dsx1DataStreamStatInDiscards		1.3.6.1.4.1.164.3.1.6.4.1.5.1.6
The counter associated with the number of Discarded incoming frames, encountered by the DS1 Data Stream.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

dsx1DataStreamStatInErrors		1.3.6.1.4.1.164.3.1.6.4.1.5.1.7
The counter associated with the number of received Errored frames, encountered by the DS1 Data Stream.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

dsx1DataStreamStatOutFrames		1.3.6.1.4.1.164.3.1.6.4.1.5.1.8
The counter associated with the number of transmitted frames, encountered by the DS1 Data Stream.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

dsx1DataStreamStatOutBytes		1.3.6.1.4.1.164.3.1.6.4.1.5.1.9
The counter associated with the number of transmitted bytes, encountered by the DS1 Data Stream.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

dsx1DataStreamStatOutDiscards		1.3.6.1.4.1.164.3.1.6.4.1.5.1.10
The counter associated with the number of Discarded outgoing frames, encountered by the DS1 Data Stream.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

dsx1DataStreamStatOutErrors		1.3.6.1.4.1.164.3.1.6.4.1.5.1.11
The counter associated with the number of errored transmitted frames, encountered by the DS1 Data Stream.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

dsx1XConfigTable		1.3.6.1.4.1.164.3.1.6.4.2
An extension to the DS1 Configuration table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Dsx1XConfigEntry

dsx1XConfigEntry		1.3.6.1.4.1.164.3.1.6.4.2.1
An entry containing additional configuration parameters.
Status: current	Access: not-accessible
OBJECT-TYPE
	Dsx1XConfigEntry

dsx1IdleCode		1.3.6.1.4.1.164.3.1.6.4.2.1.1
Byte pattern of the data received/transmitted in the E1T1 framer idle timeslots. Valid range: (0 - FF HEX).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

dsx1LineMode		1.3.6.1.4.1.164.3.1.6.4.2.1.2
T1 device operation mode. Valid for T1 only.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	csu(1), dsu(2)

dsx1dBTxGain		1.3.6.1.4.1.164.3.1.6.4.2.1.3
Transmit line Gain for T1 CSU line mode.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), neg75dB(2), neg15dB(3), neg225dB(4), zerodB(5)

dsx1RxSensitivity		1.3.6.1.4.1.164.3.1.6.4.2.1.4
Low Sensitivity is considered Short Haul while High Sensitivity is considered Long Haul. The actual values depend on the LIU. Examples: - E1: -12dB is considered Short Haul ; -43dB is considered Long Haul - T1: -12dB is considered Short Haul ; -36dB is considered Long Haul.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), longHaul(2), shortHaul(3)

dsx1RestoreTime		1.3.6.1.4.1.164.3.1.6.4.2.1.5
Used to change the sync. algorithms to reduce the time required for the port to return to normal operation after a RED alarm. 'sec1' = Fast, 'sec10' = TR-6211, 'immediate' = CCITT
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), sec1(2), sec10(3), immediate(4)

dsx1TcFirstSignal		1.3.6.1.4.1.164.3.1.6.4.2.1.6
Trunk conditioning signal - value to be sent as a signal during the first 2.5 seconds after alarm detection. Range is 0x0..0xF. 0xFF is a NULL value. This variable is used also for Space Signaling Code (in this case 0xFF is not NULL).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

dsx1TcSignal		1.3.6.1.4.1.164.3.1.6.4.2.1.7
Trunk conditioning signal value after alarm detection. Range is 0x1..0xF for E1, and 0x0..0xF for T1. This variable is used also for Space Signaling Code (E1 and T1).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

dsx1TcPattern		1.3.6.1.4.1.164.3.1.6.4.2.1.8
Trunk conditioning data pattern to be sent upon a DS0 fail. Range is 0x0..0xFF. This variable used also for Out of Service Code.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

dsx1Scramble		1.3.6.1.4.1.164.3.1.6.4.2.1.9
Scrambling is an operation that randomizes the bits of the payload of the ATM cell by a polynom. This operation helps with the error detection mechanism of the HEC. Not applicable for E1. active - will scramble/descramble the payload ATM cell notActive - will not scramble/descramble.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), notActive(2), active(3)

dsx1LineAdaptiveTimingMode		1.3.6.1.4.1.164.3.1.6.4.2.1.10
Enables end to end clock synchronization. Default value - off.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(1), on(2)

dsx1TxClockSource		1.3.6.1.4.1.164.3.1.6.4.2.1.11
The source of Transmit Clock. 'loopTiming' indicates that the recovered receive clock is used as the transmit clock. 'localTiming' indicates that a local clock source is used or when an external clock is attached to the box containing the interface. 'throughTiming' indicates that recovered receive clock from another interface is used as the transmit clock. 'adaptive' indicates that the clock is recovered according to the received data flow rate. 'system' indicates that the system clock is used as the transmit clock.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	loopTiming(1), localTiming(2), throughTiming(3), adaptive(4), system(5)

dsx1AisEnable		1.3.6.1.4.1.164.3.1.6.4.2.1.12
Enable/ disable AIS transmit when Ethernet cable (for TDMoIP) is out (disconnected).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), enable(3)

dsx1TsEchoCancel		1.3.6.1.4.1.164.3.1.6.4.2.1.13
This parameter defines for each TS whether Echo-Cancellation is on. Each bit represents one TS as follow: First octet bit'0' = TS#1, bit'7' = TS#8, .. 2nd octet bit'0' = TS#9,.., 4th octet bit'7' = TS#32. Octets and bits order is from left to right: [31,30,..24] [23..16] [15..8] [7..0] MSB LSB MSB LSB MSB LSB MSB LSB For each bit values are: 0 - Echo-Cancellation off. 1 - Echo-Cancellation on.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(4)

dsx1EchoCancelerModule		1.3.6.1.4.1.164.3.1.6.4.2.1.14
This parameter indicates whether echo-cancellation module exists for this line.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notExist(2), exist(3)

dsx1PortFunction		1.3.6.1.4.1.164.3.1.6.4.2.1.15
This object determines the ATM Mode over the physical port. uni - The port will function as an ATM UNI. ces - The port will function as a CES. ima - The port will function as an IMA-ATM. cesPsn - The port will function as a CES-PSN. abis - The port will function as an Abis.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), uni(2), ces(3), ima(4), cesPsn(5), abis(6)

dsx1PortMultiplier		1.3.6.1.4.1.164.3.1.6.4.2.1.16
This object determines the data rate of each TS (Kbps units). This parameter is applicable for T1 only.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), r56(2), r64(3)

dsx1LeasedLine		1.3.6.1.4.1.164.3.1.6.4.2.1.17
This parameter defines whether Line mode is regular (non Leased Line mode) or transparent (Leased Line mode).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), enable(3)

dsx1CsuLoop		1.3.6.1.4.1.164.3.1.6.4.2.1.18
This parameter defines where the CSU loop will be done: local - locally (by IPmux) towards the TDM device transparent - transferred to Remote Device that will send it to its connected TDM device. remote - Remote Device will close the loop towards the Local Device.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), local(2), transparent(3), remote(4)

dsx1ClockSource		1.3.6.1.4.1.164.3.1.6.4.2.1.19
This entry specifies the source from which the clock will be taken. Refer to device specification for source Index
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

dsx1OosSignal		1.3.6.1.4.1.164.3.1.6.4.2.1.20
This parameter defines the value to be sent as a signal after alarm detection: 'Space' = both A and B signaling bits are forced to '0' during out-of-service periods. 'Mark' = both A and B signaling bits are forced to '1' during out-of-service periods. 'spaceMark' = A and B bits are forced to '0' for 2.5 seconds; then they are switched to '1' until out-of-service condition disappears. 'markSpace' = A and B bits are forced to '1' for 2.5 seconds; then they are switched to '0' until out-of-service condition disappears. - '0'= 0 for T1, 1 for E1, or user defined value for Space - '1'= 1 for T1, 0 for E1, or user defined value for Mark.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), space(2), mark(3), spaceMark(4), markSpace(5)

dsx1BundleNextIndex		1.3.6.1.4.1.164.3.1.6.4.2.1.21
This parameter indicates the Next free Bundle Index for this DS1 port.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

dsx1CRC6CalcMode		1.3.6.1.4.1.164.3.1.6.4.2.1.22
This object determines the CRC6 Calculation mode. jtG704 =JT-G704 = the Japanese standard ituG704=ITU-G704 = the International standard This parameter is applicable for J1 only.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	jtG704(1), ituG704(2)

dsx1SendUponFail		1.3.6.1.4.1.164.3.1.6.4.2.1.23
This object determines which notification will be sent to the other side upon fail of another interface. In Ipmux14 the notification is sent upon failure of the Ethernet link.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	oosCode(2), ais(3)

ds1LocalMultiframeAlarmTrap		1.3.6.1.4.1.164.3.1.6.4.0.1
This trap indicates near end (Local) Loss of Multiframe Alignment, of the user E1 interface.
Status: current	Access: read-write
NOTIFICATION-TYPE

ds1RemoteMultiframeAlarmTrap		1.3.6.1.4.1.164.3.1.6.4.0.2
This trap indicates that the far end (remote) unit, connected to the user E1 interface, reports Loss of Multiframe Alignment.
Status: current	Access: read-write
NOTIFICATION-TYPE

ds1LinkFrameSlipTrap		1.3.6.1.4.1.164.3.1.6.4.0.3
This trap indicates that a Frame Slip occurred at the user DS1 interface. This usually indicates timing problems (incorrect selection of timing reference), on the user DS1 link.
Status: current	Access: read-write
NOTIFICATION-TYPE

ds1BpvErrorTrap		1.3.6.1.4.1.164.3.1.6.4.0.4
This trap indicates a Bipolar Violation (BPV) error has been detected at the user DS1 interface.
Status: current	Access: read-write
NOTIFICATION-TYPE

ds1ExcessiveBpvTrap		1.3.6.1.4.1.164.3.1.6.4.0.5
This trap indicates excessive number of Bipolar Violation errors (BPV) detected by the user DS1 interface
Status: current	Access: read-write
NOTIFICATION-TYPE

ds1Crc4ErrorTrap		1.3.6.1.4.1.164.3.1.6.4.0.6
This trap indicates that a frame with CRC-4 error has been detected at the user DS1 interface.
Status: current	Access: read-write
NOTIFICATION-TYPE

ds1ExcessiveErrorRatioTrap		1.3.6.1.4.1.164.3.1.6.4.0.7
This trap indicates that the error rate, detected at the user DS1 interface, on the frame synchronization bits is high, as defined by ITU-T Rec. G.732.
Status: current	Access: read-write
NOTIFICATION-TYPE

ds1RemoteSyncLossTrap		1.3.6.1.4.1.164.3.1.6.4.0.8
This trap indicates that the far-end (remote) unit, connected to user DS1 interface, reports Loss of Frame Alignment (Sync Loss).
Status: current	Access: read-write
NOTIFICATION-TYPE

ds1LocalSyncLossTrap		1.3.6.1.4.1.164.3.1.6.4.0.9
This trap indicates near end (Local) Loss of Frame Alignment failure (Sync Loss), of the user DS1 interface
Status: current	Access: read-write
NOTIFICATION-TYPE

ds1AisSyncLossTrap		1.3.6.1.4.1.164.3.1.6.4.0.10
This trap indicates near end (Local) Loss of Frame Alignment (Sync Loss), caused by the reception of AIS at the user DS1 interface.
Status: current	Access: read-write
NOTIFICATION-TYPE

ds1AisTrap		1.3.6.1.4.1.164.3.1.6.4.0.11
This trap indicates AIS being received at the user DS1 interface.
Status: current	Access: read-write
NOTIFICATION-TYPE

ds1NetworkRemoteLoopTrap		1.3.6.1.4.1.164.3.1.6.4.0.12
This trap indicates that a remote loopback has been activated, on the local uplink interface.
Status: current	Access: read-write
NOTIFICATION-TYPE

ds1RemoteLoopTrap		1.3.6.1.4.1.164.3.1.6.4.0.13
This trap indicates that a remote loopback has been activated, on the local user port.
Status: current	Access: read-write
NOTIFICATION-TYPE

ds1LocalLoopTrap		1.3.6.1.4.1.164.3.1.6.4.0.14
This trap indicates that a local loopback has been activated on the user port.
Status: current	Access: read-write
NOTIFICATION-TYPE

ds1ExcessiveFrameSlipTrap		1.3.6.1.4.1.164.3.1.6.4.0.15
This trap indicates that the number of Frame Slips detected at the user DS1 interface, during the last minute exceeds threshold. For LA-110, threshold value is 10. This usually indicates timing problems (incorrect selection of timing reference) on the user DS1.
Status: current	Access: read-write
NOTIFICATION-TYPE

ds1ExcessiveCrc4ErrorTrap		1.3.6.1.4.1.164.3.1.6.4.0.16
This trap indicates that the error rate detected on the CRC-4 bits at the user DS1 interface, is high.
Status: current	Access: read-write
NOTIFICATION-TYPE

ds1ExcessiveLocalMfAlarmTrap		1.3.6.1.4.1.164.3.1.6.4.0.17
This trap indicates that the number of local Loss of Multiframe Alignment events, detected at the user E1 interface during the last minute exceeds threshold. For LA-110, threshold value is 10.
Status: current	Access: read-write
NOTIFICATION-TYPE

ds1ExcessiveRemoteMfAlarmTrap		1.3.6.1.4.1.164.3.1.6.4.0.18
This trap indicates that the number of Loss of multiframe alignment events reported by the remote unit connected to the user E1 interface during the last minute exceeds threshold. For LA-110, threshold value is 10.
Status: current	Access: read-write
NOTIFICATION-TYPE

ds1ExcessiveRemoteSyncLossTrap		1.3.6.1.4.1.164.3.1.6.4.0.19
This trap indicates that the number of far end (remote) Loss of Synchronization alarms, reported by the user DS1 interface during the last minute, exceeds threshold. For LA-110, threshold value is 10.
Status: current	Access: read-write
NOTIFICATION-TYPE

ds1ExcessiveLocalSyncLossTrap		1.3.6.1.4.1.164.3.1.6.4.0.20
This trap indicates that the number of Loss of local Synchronization alarms reported by the user DS1 interface during the last minute, exceeds threshold. For LA-110, threshold value is 10.
Status: current	Access: read-write
NOTIFICATION-TYPE

ds1SignalLossTrap		1.3.6.1.4.1.164.3.1.6.4.0.21
This trap indicates Signal Loss. (possible reason - cable disconnection. etc.)
Status: current	Access: read-write
NOTIFICATION-TYPE

ds3Interface		1.3.6.1.4.1.164.3.1.6.3
OBJECT IDENTIFIER

prtDs3PerfHistory		1.3.6.1.4.1.164.3.1.6.3.1
OBJECT IDENTIFIER

prtSDs3IfTable		1.3.6.1.4.1.164.3.1.6.3.1.1
The DS3 interface table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtDs3IfEntry

prtDs3IfEntry		1.3.6.1.4.1.164.3.1.6.3.1.1.1
An entry in the DS3 interface table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtDs3IfEntry

prtDs3IfTimeElapsed		1.3.6.1.4.1.164.3.1.6.3.1.1.1.1
The number of seconds that have elapsed since the beginning of the near end current error- measurement period.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..899

prtDs3IfValidIntervals		1.3.6.1.4.1.164.3.1.6.3.1.1.1.2
The number of previous near end intervals for which valid data was collected. The value will be 96 unless the interface was brought online within the last 24 hours, in which case the value will be the number of complete 15 minute near end intervals since the interface has been online.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..96

prtDs3CurrentTable		1.3.6.1.4.1.164.3.1.6.3.1.2
The DS3 Current table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtDs3CurrentEntry

prtDs3CurrentEntry		1.3.6.1.4.1.164.3.1.6.3.1.2.1
An entry in the DS3 Current table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtDs3CurrentEntry

prtDs3CurrentLOS		1.3.6.1.4.1.164.3.1.6.3.1.2.1.1
The counter associated with the number of LOS seconds, encountered by a DS3 interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtDs3CurrentOOF		1.3.6.1.4.1.164.3.1.6.3.1.2.1.2
The counter associated with the number of OOF seconds, encountered by a DS3 interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtDs3CurrentLOC		1.3.6.1.4.1.164.3.1.6.3.1.2.1.3
The counter associated with the number of LOC seconds, encountered by a DS3 interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtDs3CurrentAIS		1.3.6.1.4.1.164.3.1.6.3.1.2.1.4
The counter associated with the number of AIS seconds, encountered by a DS3 interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtDs3CurrentRDI		1.3.6.1.4.1.164.3.1.6.3.1.2.1.5
The counter associated with the number of RDI seconds, encountered by a DS3 interface.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtDs3CurrentUAS		1.3.6.1.4.1.164.3.1.6.3.1.2.1.6
The counter associated with the number of UAS, encountered by a SONET interface.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtDs3CurrentBIP		1.3.6.1.4.1.164.3.1.6.3.1.2.1.7
The counter associated with the number of BIP errors, encountered by a DS3 interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtDs3CurrentFEBE		1.3.6.1.4.1.164.3.1.6.3.1.2.1.8
The counter associated with the number of FEBE errors, encountered by a DS3 interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtDs3CurrentSLM		1.3.6.1.4.1.164.3.1.6.3.1.2.1.9
The counter associated with the number of SLM seconds, encountered by an E3 (only ) interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtDs3CurrentSES		1.3.6.1.4.1.164.3.1.6.3.1.2.1.10
The counter associated with the number of SES encountered by a E3 interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtDs3CurrentES		1.3.6.1.4.1.164.3.1.6.3.1.2.1.11
The number of Errored Seconds, encountered by a DS3 interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtDs3CurrentBitParity		1.3.6.1.4.1.164.3.1.6.3.1.2.1.12
Bit Parity Error counter. Relevant to T3 only.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtDs3CurrentPlcpLOF		1.3.6.1.4.1.164.3.1.6.3.1.2.1.13
The counter associated with the number of LOF seconds, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals. This counter is relevant for plcpInternal(5) or plcpExternal(6) configuration If frame types only.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtDs3CurrentPlcpRAI		1.3.6.1.4.1.164.3.1.6.3.1.2.1.14
Receiving Yellow/Remote Alarm Indication. This counter is relevant for PLCP (external/internal) frame types only.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtDs3CurrentPlcpBIP		1.3.6.1.4.1.164.3.1.6.3.1.2.1.15
The counter associated with the number of BIP errors, encountered by a DS3 interface in the current 15 minute interval. This counter is relevant for PLCP (external/internal) frame types only.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtDs3CurrentPlcpFEBE		1.3.6.1.4.1.164.3.1.6.3.1.2.1.16
The counter associated with the number of FEBE errors, encountered by a DS3 interface in the current 15 minute interval. This counter is relevant for PLCP (external/internal) frame types only.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtDs3CurrentBPV		1.3.6.1.4.1.164.3.1.6.3.1.2.1.17
Number of BPVs (Bi-Polar Violations) , encountered by a DS3 interface in the current 15 minute interval. This object is relevant only for Electrical Line of Fomi-E3/T3.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtDs3CurrentLCE		1.3.6.1.4.1.164.3.1.6.3.1.2.1.18
Number of LCE (Link Code Errors) encountered by a DS3 interface in the current 15 minute interval. This object is relevant only for Optical Links of Fomi-E3/T3.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtDs3CurrentStatus		1.3.6.1.4.1.164.3.1.6.3.1.2.1.19
The statuses of the current interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was partialy out. 4 - notValid - module is out.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(4)

prtDs3IntervalTable		1.3.6.1.4.1.164.3.1.6.3.1.3
The DS3 Interval table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtDs3IntervalEntry

prtDs3IntervalEntry		1.3.6.1.4.1.164.3.1.6.3.1.3.1
An entry in the DS3 Interval table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtDs3IntervalEntry

prtDs3IntervalNumber		1.3.6.1.4.1.164.3.1.6.3.1.3.1.1
A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..96

prtDs3IntervalLOS		1.3.6.1.4.1.164.3.1.6.3.1.3.1.2
The counter associated with the number of LOS seconds , encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtDs3IntervalOOF		1.3.6.1.4.1.164.3.1.6.3.1.3.1.3
The counter associated with the number of OOF seconds, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtDs3IntervalLOC		1.3.6.1.4.1.164.3.1.6.3.1.3.1.4
The counter associated with the number of LOC seconds, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtDs3IntervalAIS		1.3.6.1.4.1.164.3.1.6.3.1.3.1.5
The counter associated with the number of AIS seconds, encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtDs3IntervalRDI		1.3.6.1.4.1.164.3.1.6.3.1.3.1.6
The counter associated with the number of RDI seconds, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtDs3IntervalUAS		1.3.6.1.4.1.164.3.1.6.3.1.3.1.7
The counter associated with the number of UAS, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtDs3IntervalBIP		1.3.6.1.4.1.164.3.1.6.3.1.3.1.8
The counter associated with the number of BIP errors, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtDs3IntervalFEBE		1.3.6.1.4.1.164.3.1.6.3.1.3.1.9
The counter associated with the number of FEBE errors, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtDs3IntervalSLM		1.3.6.1.4.1.164.3.1.6.3.1.3.1.10
The counter associated with the number of SLM seconds, encountered by an E3 interface in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtDs3IntervalSES		1.3.6.1.4.1.164.3.1.6.3.1.3.1.11
The counter associated with the number of SES encountered by a E3 interface in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtDs3IntervalES		1.3.6.1.4.1.164.3.1.6.3.1.3.1.12
The number of Errored Seconds, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtDs3IntervalBitParity		1.3.6.1.4.1.164.3.1.6.3.1.3.1.13
Bit Parity Error counter. Relevant to T3 only.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtDs3IntervalPlcpLOF		1.3.6.1.4.1.164.3.1.6.3.1.3.1.14
The counter associated with the number of LOF seconds, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals. This counter is relevant for plcpInternal(5) or plcpExternal(6) configuration If frame types only.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtDs3IntervalPlcpRAI		1.3.6.1.4.1.164.3.1.6.3.1.3.1.15
Receiving Yellow/Remote Alarm Indication. This counter is relevant for PLCP (external/internal) frame types only.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtDs3IntervalPlcpBIP		1.3.6.1.4.1.164.3.1.6.3.1.3.1.16
The counter associated with the number of BIP errors, encountered by a DS3 interface in the current 15 minute interval. This counter is relevant for PLCP (external/internal) frame types only.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtDs3IntervalPlcpFEBE		1.3.6.1.4.1.164.3.1.6.3.1.3.1.17
The counter associated with the number of FEBE errors, encountered by a DS3 interface in the current 15 minute interval. This counter is relevant for PLCP (external/internal) frame types only.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtDs3IntervalBPV		1.3.6.1.4.1.164.3.1.6.3.1.3.1.18
Number of BPVs (Bi-Polar Violations) , encountered by a DS3 interface in the specified 15 minute interval. This object is relevant only for Electrical Line of Fomi-E3/T3.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtDs3IntervalLCE		1.3.6.1.4.1.164.3.1.6.3.1.3.1.19
Number of LCE (Link Code Errors) encountered by a DS3 interface in the specified 15 minute interval. This object is relevant only for Optical Links of Fomi-E3/T3.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtDs3IntervalStatus		1.3.6.1.4.1.164.3.1.6.3.1.3.1.20
The statuses of the current interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was partialy out. 4 - notValid - module is out.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(4)

prtDs3TotalTable		1.3.6.1.4.1.164.3.1.6.3.1.4
A list of Total entries.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtDs3TotalEntry

prtDs3TotalEntry		1.3.6.1.4.1.164.3.1.6.3.1.4.1
An entry of Total table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtDs3TotalEntry

prtDs3TotalUAS		1.3.6.1.4.1.164.3.1.6.3.1.4.1.6
Number of UASs (Unavailable Seconds) , encountered by a DS3 interface in the previous 96 intervals. Invalid 15 minute intervals count as 0.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtDs3TotalBPV		1.3.6.1.4.1.164.3.1.6.3.1.4.1.17
Number of BPVs (Bi-Polar Violations) , encountered by a DS3 interface in the previous 96 intervals. Invalid 15 minute intervals count as 0.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtDs3TotalLCE		1.3.6.1.4.1.164.3.1.6.3.1.4.1.18
Number of LCE (Link Code Errors) encountered by a DS3 interface in the previous 96 intervals. Invalid 15 minute intervals count as 0.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtDs3TotalSES		1.3.6.1.4.1.164.3.1.6.3.1.4.1.19
Number of SES (Severely Errored Seconds) encountered by a DS3 interface in the previous 96 intervals. Invalid 15 minute intervals count as 0.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

dsx3XConfigTable		1.3.6.1.4.1.164.3.1.6.3.2
An extension to the DS3 Configuration table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Dsx3XConfigEntry

dsx3XConfigEntry		1.3.6.1.4.1.164.3.1.6.3.2.1
An entry containing additional configuration parameters.
Status: current	Access: not-accessible
OBJECT-TYPE
	Dsx3XConfigEntry

dsx3AisEnable		1.3.6.1.4.1.164.3.1.6.3.2.1.1
Enable/ disable AIS transmit when Ethernet (for TDMoIP) line is disconnected.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), enable(3)

dsx3TxClockSource		1.3.6.1.4.1.164.3.1.6.3.2.1.2
The source of Transmit Clock. loopTiming indicates that the recovered receive clock is used as the transmit clock. localTiming indicates that a local clock source is used or that an external clock is attached to the box containing the interface. throughTiming indicates that transmit clock is derived from the recovered receive clock of another DS3 interface. 'system' indicates that the system clock is used as the transmit clock.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	loopTiming(1), localTiming(2), throughTiming(3), system(4)

dsx3MappingTable		1.3.6.1.4.1.164.3.1.6.3.3
The DS3/E3 mapping table associates DS3/E3 channels with logical or physical interfaces. For example, consider a DS3 device with 16 T1's and 1 VCG. There are 28 logical/internal channels, numbered 1 through 28 but only 17 are actually connected. We might describe the allocation of channels, in the dsx3MappingTable, as follows: dsx3MappingIfIndex.1. 1 = 1001 dsx3MappingIfIndex.1.15 = 1015 dsx3MappingIfIndex.1. 2 = 1002 dsx3MappingIfIndex.1.16 = 1016 dsx3MappingIfIndex.1. 3 = 1003 dsx3MappingIfIndex.1.17 = 1017 dsx3MappingIfIndex.1. 4 = 1004 dsx3MappingIfIndex.1.18 = 0 dsx3MappingIfIndex.1. 5 = 1005 dsx3MappingIfIndex.1.19 = 0 dsx3MappingIfIndex.1. 6 = 1006 dsx3MappingIfIndex.1.20 = 0 dsx3MappingIfIndex.1. 7 = 1007 dsx3MappingIfIndex.1.21 = 0 dsx3MappingIfIndex.1. 8 = 1008 dsx3MappingIfIndex.1.22 = 0 dsx3MappingIfIndex.1. 9 = 1009 dsx3MappingIfIndex.1.23 = 0 dsx3MappingIfIndex.1.10 = 1010 dsx3MappingIfIndex.1.24 = 0 dsx3MappingIfIndex.1.11 = 1011 dsx3MappingIfIndex.1.25 = 0 dsx3MappingIfIndex.1.12 = 1012 dsx3MappingIfIndex.1.26 = 0 dsx3MappingIfIndex.1.13 = 1013 dsx3MappingIfIndex.1.27 = 0 dsx3MappingIfIndex.1.14 = 1014 dsx3MappingIfIndex.1.28 = 0 Note that in the case above all channels are mapped to one T3 port with ifIndex = 1. The Channels 1...28 are represented via the 2nd index. The values of 1001...1016 are the T1 interface ifIndexes. The value of 1017 is the ifIndex of the VCG. Unconnected channels have a value of 0.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Dsx3MappingEntry

dsx3MappingEntry		1.3.6.1.4.1.164.3.1.6.3.3.1
An entry in the DS3 mapping table.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	Dsx3MappingEntry

dsx3MappingDs3Index		1.3.6.1.4.1.164.3.1.6.3.3.1.1
The index value which uniquely identifies the DS3/E3 interface to which this entry is applicable. This value is also equal to dsx3LineIndex used in dsx3ConfigEntry. For RICi-16 this is the ifIndex of the T3 interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

dsx3MappingNumber		1.3.6.1.4.1.164.3.1.6.3.3.1.2
The channel number for this entry. For RICi-16 this is the channel number 1...28.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

dsx3MappingIfIndex		1.3.6.1.4.1.164.3.1.6.3.3.1.3
An index value that uniquely identifies a logical or physical interface mapped to a DS3/E3 channel. If no interface is currently using a channel, the value should be zero. If a single interface occupies more than one channel, that ifIndex value will be found in multiple channels. For RICi-16 this is the ifIndex of the T1 or VCG interface.
Status: current	Access: read-write
OBJECT-TYPE
	InterfaceIndex

atmNte		1.3.6.1.4.1.164.12.3
OBJECT IDENTIFIER

atmNtePrt		1.3.6.1.4.1.164.12.3.2
OBJECT IDENTIFIER

atmNtePrtConfig		1.3.6.1.4.1.164.12.3.2.1
OBJECT IDENTIFIER

atmNteEvents		1.3.6.1.4.1.164.12.3.0
The events for RAD ATM products.
Status: current	Access: read-write
OBJECT-IDENTITY

atmNteConfIfTable		1.3.6.1.4.1.164.12.3.2.1.1
The Physical interface configuration table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmNteConfIfEntry

atmNteConfIfEntry		1.3.6.1.4.1.164.12.3.2.1.1.1
An entry in the Physical interface configuration table. The ifIndex is of the lowest physical layer.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmNteConfIfEntry

atmConfIfTransmitClk		1.3.6.1.4.1.164.12.3.2.1.1.1.1
The transmit clock of the port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	internal(2), external(3), loopback(4), adaptive(5)

atmConfIfLoopback		1.3.6.1.4.1.164.12.3.2.1.1.1.2
Interface Loopback.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	internal(2), external(3), disable(4)

atmConfIfFrameType		1.3.6.1.4.1.164.12.3.2.1.1.1.3
The frame type. Valid values for a 155M interface: sonet(2), sdh(3). Valid values for a T3 interface: direct(4), plcpInternal(5), plcpExternal(6), directNoScrmbling(10), plcpInternalNoScrmbling(11), plcpExternalNoScrmbling(12). Valid values for Ethernet interface: ethCrcTrans (8), ethCrcNotTrans(9). (DS1 interfaces frame type is specified in the DSX1 mib).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), sonet(2), sdh(3), direct(4), plcpInternal(5), plcpExternal(6), e3(7), ethCrcTrans(8), ethCrcNotTrans(9), directNoScrmbling(10), plcpInternalNoScrmbling(11), plcpExternalNoScrmbling(12)

atmConfIfCardType		1.3.6.1.4.1.164.12.3.2.1.1.1.4
The card type.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), sc13m-155(2), st13s-155(3), st13l-155(4), utp-155(5), cx-bnc-155(6), e3(7), t3(8), e1(9), e1-ltu(10), fc13l-155(11), fc13lh-155(12), fc15lh-155(13), fc13l-e3(14), fc13lh-e3(15), fc15lh-e3(16), fc13l-t3(17), fc13lh-t3(18), fc15lh-t3(19)

atmConfAtmIfVpiVciLimit		1.3.6.1.4.1.164.12.3.2.1.1.1.5
The limit on the sum of the VPI+VCI bits for this interface.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	bits15(2), bits17(3)

atmConfIfHwFeatures		1.3.6.1.4.1.164.12.3.2.1.1.1.6
HW features command.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

atmConfIfOutputRate		1.3.6.1.4.1.164.12.3.2.1.1.1.7
This parameter indicates the output rate in cells/sec, which is supported per port. Successfully setting this parameter is dependent on all other ports values calculations, which are described in the NMS SRS.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmConfIfInputRate		1.3.6.1.4.1.164.12.3.2.1.1.1.8
This parameter indicates the input rate in cells/sec, which is supported per port. Successfully setting this parameter is dependent on all other ports values calculations, which are described in the NMS SRS.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmConfAlarmForwarding		1.3.6.1.4.1.164.12.3.2.1.1.1.9
Enables Path AIS Alarm forwarding upon a failure detection. The following might be considered as a failure: LOS, LOF, LOC, SLM, LOP, Path AIS and Line AIS. disable(2) - will not forward an alarm upon a failure on this port. enable(3) - will forward an alarm upon a failure on this port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(2), enable(3)

atmConfIfAllocatedBw		1.3.6.1.4.1.164.12.3.2.1.1.1.10
Total VC Bandwidth Allocation.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmConfIfLowerVpi		1.3.6.1.4.1.164.12.3.2.1.1.1.11
The Lower possible VPI.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmConfIfOamMode		1.3.6.1.4.1.164.12.3.2.1.1.1.12
OAM support Mode, which determines the interface's location in a segment wise.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	segmentTermination(2), endToEndTermination(3)

atmConfIfOamFailureInd		1.3.6.1.4.1.164.12.3.2.1.1.1.13
This object allows user to define the type of indication (if any) that will be created upon a LB cell failure, for all VCs on which OAM loopback traffic is activated. disabled(2) - no indication will be created. ais(3) - will cause Tx of AIS. rdi(4) - will cause Tx of RDI. aisAndRdi(5) - will cause Tx of AIS & RDI. For LA-110, indication will be sent only for VCs with atmConfVcLoopbackFailureInd <> disabled
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(2), ais(3), rdi(4), aisAndRdi(5)

atmNteAlarmIfTable		1.3.6.1.4.1.164.12.3.2.1.2
The interface Alarm table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmNteAlarmIfEntry

atmNteAlarmIfEntry		1.3.6.1.4.1.164.12.3.2.1.2.1
An entry in the interface Alarm table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmNteAlarmIfEntry

atmInterfaceActiveAlarms		1.3.6.1.4.1.164.12.3.2.1.2.1.1
A Bit String of the active alarms on this interface. An up bit (1) means there is an active alarm of this type. A down bit (0) means there is no such alarm. The meaning of the bits is as follows: 1 - LOS 2 - LOF 3 - Line AIS (SONET)/ PLCP LOF (DS3) 4 - LOP 5 - Path AIS 6 - SLM 7 - LCD 8 - Line RDI (SONET)/ PLCP Yellow (DS3) 9 - Path RDI (SONET)/ RDI (DS3) 10 - Section BIP (SONET)/ P1/P2 (DS3) > Threshold 11 - Line BIP (SONET)/ PLCP BIP (DS3) > Threshold 12 - Line FEBE (SONET)/ PLCP FEBE (DS3) > Threshold 13 - Path BIP > Threshold 14 - Path FEBE > Threshold 15 - HW Failure
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmThresholdSectionBIP		1.3.6.1.4.1.164.12.3.2.1.2.1.2
When Section BIPs are greater than this threshold, an active alarm is raised. N/A for ds3/e3 interface.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmThresholdLineBIP		1.3.6.1.4.1.164.12.3.2.1.2.1.3
When Line BIPs are greater than this threshold, an active alarm is raised. N/A for ds3/e3 interface.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmThresholdLineFEBE		1.3.6.1.4.1.164.12.3.2.1.2.1.4
When Line FEBEs are greater than this threshold, an active alarm is raised. N/A for ds3/e3 interface.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmThresholdPathBIP		1.3.6.1.4.1.164.12.3.2.1.2.1.5
When Path BIPs are greater than this threshold, an active alarm is raised.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmThresholdPathFEBE		1.3.6.1.4.1.164.12.3.2.1.2.1.6
When Path FEBEs are greater than this threshold, an active alarm is raised.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmThresholdErroredCells		1.3.6.1.4.1.164.12.3.2.1.2.1.7
When Errored Cells are greater than this threshold, an active alarm is raised.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmThresholdLostCells		1.3.6.1.4.1.164.12.3.2.1.2.1.8
When Lost Cells are greater than this threshold, an active alarm is raised.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmThresholdMisinsertedCells		1.3.6.1.4.1.164.12.3.2.1.2.1.9
When Misinserted Cells are greater than this threshold, an active alarm is raised.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmInterfaceAlarmStatus		1.3.6.1.4.1.164.12.3.2.1.2.1.10
The variable is on(3) when there is any active alarm on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), on(3)

atmInterfaceMaskAlarms		1.3.6.1.4.1.164.12.3.2.1.2.1.11
A Bit String of alarms mask on this interface. An up bit (1) means that the respective alarm is masked. A down bit (0) means no mask. The mask is supported for the following alarms: 1 - LOS
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmNteConfVpTable		1.3.6.1.4.1.164.12.3.2.1.3
The ATM VP configuration table. The table is an extension to the atmVplTable of RFC-1695.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmNteConfVpEntry

atmNteConfVpEntry		1.3.6.1.4.1.164.12.3.2.1.3.1
An entry in the ATM VP configuration table. ifIndex of the ATM layer.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmNteConfVpEntry

atmConfVpPolicing		1.3.6.1.4.1.164.12.3.2.1.3.1.1
Policing method desired for this VPL.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), police(2), monitor(3), shaping(4), policingAndShaping(5)

atmConfVpCCAdminStatus		1.3.6.1.4.1.164.12.3.2.1.3.1.2
up(2) - Activate Continuity Check (CC). down(3) - Deactivate CC. source(4) - Activate OAM CC(Continuity Check) of local agent ( start sending Oam cells to the remote side ). sink(5) - Activate CC of remote agent ( start receiving Oam cells from remote side ). listenToActivationCells (6) - Passive listener till gets an activation request originateActivationCells(7) - Sands Activation cell according to atmConfVcCCDirection.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	up(2), down(3), source(4), sink(5), listenToActivationCells(6), originateActivationCells(7)

atmConfVpLoopbackAdminStatus		1.3.6.1.4.1.164.12.3.2.1.3.1.3
up(2) - Start loopback OAM cells. down(3) - Stop sending loopback OAM cells. For ace2002: up(2) - Transmitting LB cells with llid all ones (i.e. FFFF..FF) down(3) - Not transmitting LB cells. llid(4) - Transmitting LB cells with llid indicated in the address field. segment(5) - Transmitting Segment LB cells with llid all ones. endToEnd(6) - Transmitting End to End LB cells with llid all ones. segmentLlid(7) - Transmitting Segment LB cells with llid indicated in the address field. endToEndLlid(8) - Transmitting LB cells with llid indicated in the address field. This parameter value might be in conflict with atmConfVpOamSupport value, since this parameter is for LB, while atmConfVpOamSupport is for any other OAM cells.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	up(2), down(3), llid(4), segment(5), endToEnd(6), segmentLlid(7), endToEndLlid(8)

atmConfVpLoopbackSinkAddress		1.3.6.1.4.1.164.12.3.2.1.3.1.4
Destination address. For ace101: 2 bytes are used. For ace2002: 16 bytes are used.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..20)

atmConfVpCongestionControl		1.3.6.1.4.1.164.12.3.2.1.3.1.5
Each bit indicates a selection of one option as the following description. All combinations are possible and legal. The codes are: 1 - EPD 2 - CLP 4 - EFCI
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

atmConfVpCCDirection		1.3.6.1.4.1.164.12.3.2.1.3.1.6
both(2) - Agent send OAM CC cells and check received OAM CC cells source(4)- Agent send OAM CC cells. sink(5) - Agent checks received OAM CC cells.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	both(2), source(4), sink(5)

atmConfVpCreationTime		1.3.6.1.4.1.164.12.3.2.1.3.1.7
A date-time in which the VP was created.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

atmConfVpOamSupport		1.3.6.1.4.1.164.12.3.2.1.3.1.8
OAM support mode, which determines the device location in a segment wise.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	intermediate(1), segmentTermination(2), endToEndTermination(3)

atmConfVpCCOperStatus		1.3.6.1.4.1.164.12.3.2.1.3.1.9
initial(1) - The CC activation process is not started. source(4) - Agent sends OAM CC cells. sink(5) - Agent checks received OAM CC cells. both (8) - OAM CC of local and remote agents activation. timeout (9) - Timeout occured on receiving answer from the remote agent. denied (10) - CC activation process rejected by remote agent. conflict (11) - local and remote sides requested activation simultaneously. manual (12) - OAM CC of local agent activated manually.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	initial(1), source(4), sink(5), both(8), timeout(9), denied(10), conflict(11), manual(12)

atmConfVpLoopbackTraffic		1.3.6.1.4.1.164.12.3.2.1.3.1.10
This parameter has both command and status meanings: off(2) - Set to 'Off' will Stop traffic loop. Getting this value means that the loop is not running. on (3) - Set to 'On' will start traffic loop. Getting this value means that the loop is currently running.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

atmConfVpLoopbackFailureInd		1.3.6.1.4.1.164.12.3.2.1.3.1.11
This object allows user to define the Indication that will be created upon a LB cell failure. disabled(2) - no indication will be created. segmentAis(3) - will cause Tx of a segment AIS. segmentRdi(4) - will cause Tx of a segment RDI. segmentAisAndRdi(5) - will cause Tx of a segment AIS & RDI. endToEndAis(6) - will cause Tx of an End to End AIS. endToEndRdi(7) - will cause Tx of an End to End RDI. endToEndAisAndRdi(8) - will cause Tx of an End to End AIS & RDI. Default: disabled(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(2), segmentAis(3), segmentRdi(4), segmentAisAndRdi(5), endToEndAis(6), endToEndRdi(7), endToEndAisAndRdi(8)

atmConfVpLoopbackFailureThreshold		1.3.6.1.4.1.164.12.3.2.1.3.1.12
The number of the LB failures before starting transmission of the Indication defined by atmConfVcLoopbackFailureInd. Range: 1..16. Default: 1.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmConfVpOamDirection		1.3.6.1.4.1.164.12.3.2.1.3.1.13
The direction of OAM cell insertion. downStream(2) - The OAM cell will be inserted in downStream. upStream(3) - The OAM cell will be inserted in upStream.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), downStream(2), upStream(3)

atmConfVpOamDescrIndex		1.3.6.1.4.1.164.12.3.2.1.3.1.14
This parameter indicates the VPL's OAM Descriptor index, according to the OAM Descriptor Configuration Table.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmConfVpConnected		1.3.6.1.4.1.164.12.3.2.1.3.1.15
This object indicates whether this VP is connected and if connected, what is it connected to.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notConnected(1), mng(2), bridgePort(3), ds0Bundle(4), atm(5), pw(6)

atmNteAlarmVpTable		1.3.6.1.4.1.164.12.3.2.1.5
The ATM VP Alarm table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmNteAlarmVpEntry

atmNteAlarmVpEntry		1.3.6.1.4.1.164.12.3.2.1.5.1
An entry in the ATM VP Alarm table. ifIndex of the ATM layer.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmNteAlarmVpEntry

atmNteVpAlarmVpi		1.3.6.1.4.1.164.12.3.2.1.5.1.1
The VPI on which there is an active alarm.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmNteVpActiveAlarms		1.3.6.1.4.1.164.12.3.2.1.5.1.2
A Bit String of the active alarms on this VP. An up bit (1) means there is an active alarm of this type. A down bit (0) means there is no such alarm. The meaning of the bits is as follows: 1 - VP AIS 2 - VP Loss Of Continuity 3 - VP RDI Reception 4 - VP Errored Cells > Threshold 5 - VP Lost Cells > Threshold 6 - VP Misinserted Cells > Threshold 9 - VP Loopback Failure
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmNteAlarmVcTable		1.3.6.1.4.1.164.12.3.2.1.6
The ATM VC Alarm table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmNteAlarmVcEntry

atmNteAlarmVcEntry		1.3.6.1.4.1.164.12.3.2.1.6.1
An entry in the ATM VC Alarm table. ifIndex of the ATM layer.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmNteAlarmVcEntry

atmNteVcAlarmVpi		1.3.6.1.4.1.164.12.3.2.1.6.1.1
The VPI of the VC on which there is an active alarm.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmNteVcAlarmVci		1.3.6.1.4.1.164.12.3.2.1.6.1.2
The VCI of the VC on which there is an active alarm.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmNteVcActiveAlarms		1.3.6.1.4.1.164.12.3.2.1.6.1.3
A Bit String of the active alarms on this VC. An up bit (1) means there is an active alarm of this type. A down bit (0) means there is no such alarm. The meaning of the bits is as follows: 1 - VC AIS 2 - VC Loss Of Continuity 3 - VC RDI 4 - VC Errored Cells > Threshold 5 - VC Lost Cells > Threshold 6 - VC Misinserted Cells > Threshold 7 - Tx VC AIS 8 - Tx VC RDI 9 - VC Loopback Failure
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmGen		1.3.6.1.4.1.164.12.2
OBJECT IDENTIFIER

atmPerfHistory		1.3.6.1.4.1.164.12.2.1
OBJECT IDENTIFIER

atmIfPerformance		1.3.6.1.4.1.164.12.2.1.1
OBJECT IDENTIFIER

atmIfDataTable		1.3.6.1.4.1.164.12.2.1.1.1
The ATM interface Data table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmIfDataEntry

atmIfDataEntry		1.3.6.1.4.1.164.12.2.1.1.1.1
An entry in the ATM interface Data table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmIfDataEntry

atmIfTimeElapsed		1.3.6.1.4.1.164.12.2.1.1.1.1.1
The number of seconds that have elapsed since the beginning of the near end current error- measurement period.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..899

atmIfValidIntervals		1.3.6.1.4.1.164.12.2.1.1.1.1.2
The number of previous near end intervals for which valid data was collected. The value will be 96 unless the interface was brought online within the last 24 hours, in which case the value will be the number of complete 15 minute near end intervals since the interface has been online.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..96

atmIfTxCells		1.3.6.1.4.1.164.12.2.1.1.1.1.3
The counter associated with the total number of transmitted cells, encountered by an ATM interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

atmIfRxCells		1.3.6.1.4.1.164.12.2.1.1.1.1.4
The counter associated with the total number of received cells, encountered by an ATM interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

atmIfUncorrectedHecs		1.3.6.1.4.1.164.12.2.1.1.1.1.5
The counter associated with the total number of cells with uncorrected HEC errors, encountered by an ATM interface.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

atmIfCurrentTable		1.3.6.1.4.1.164.12.2.1.1.2
The ATM interface Current table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmIfCurrentEntry

atmIfCurrentEntry		1.3.6.1.4.1.164.12.2.1.1.2.1
An entry in the ATM interface Current table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmIfCurrentEntry

atmIfCurrentTxCells		1.3.6.1.4.1.164.12.2.1.1.2.1.1
The counter associated with the number of transmitted cells, encountered by an ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmIfCurrentRxCells		1.3.6.1.4.1.164.12.2.1.1.2.1.2
The counter associated with the number of received cells, encountered by an ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmIfCurrentCorrectedHecs		1.3.6.1.4.1.164.12.2.1.1.2.1.3
The counter associated with the number of cells with corrected HEC errors, encountered by an ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmIfCurrentUncorrectedHecs		1.3.6.1.4.1.164.12.2.1.1.2.1.4
The counter associated with the number of cells with uncorrected HEC errors, encountered by an ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmIfCurrentHecErrorSeconds		1.3.6.1.4.1.164.12.2.1.1.2.1.5
The counter associated with the number of seconds with HEC errors, encountered by an ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmIfIntervalTable		1.3.6.1.4.1.164.12.2.1.1.3
The ATM interface Interval table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmIfIntervalEntry

atmIfIntervalEntry		1.3.6.1.4.1.164.12.2.1.1.3.1
An entry in the ATM interface Interval table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmIfIntervalEntry

atmIfIntervalNumber		1.3.6.1.4.1.164.12.2.1.1.3.1.1
A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..96

atmIfIntervalTxCells		1.3.6.1.4.1.164.12.2.1.1.3.1.2
The counter associated with the number of transmitted cells , encountered by an ATM interface in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmIfIntervalRxCells		1.3.6.1.4.1.164.12.2.1.1.3.1.3
The counter associated with the number of received cells, encountered by an ATM interface in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmIfIntervalCorrectedHecs		1.3.6.1.4.1.164.12.2.1.1.3.1.4
The counter associated with the number of cells with corrected HEC errors, encountered by an ATM interface in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmIfIntervalUncorrectedHecs		1.3.6.1.4.1.164.12.2.1.1.3.1.5
The counter associated with the number of cells with uncorrected HEC errors, encountered by an ATM interface in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmIfIntervalHecErrorSeconds		1.3.6.1.4.1.164.12.2.1.1.3.1.6
The counter associated with the number of seconds with HEC errors, encountered by an ATM interface in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmPvcPerformance		1.3.6.1.4.1.164.12.2.1.2
OBJECT IDENTIFIER

atmVpPerformance		1.3.6.1.4.1.164.12.2.1.2.1
OBJECT IDENTIFIER

atmVpCurrentTable		1.3.6.1.4.1.164.12.2.1.2.1.1
The ATM VP Current table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmVpCurrentEntry

atmVpCurrentEntry		1.3.6.1.4.1.164.12.2.1.2.1.1.1
An entry in the ATM VP Current table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmVpCurrentEntry

atmVpCurrentVpi		1.3.6.1.4.1.164.12.2.1.2.1.1.1.1
The VPI of the VPL.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmVpCurrentRxCellsClp01		1.3.6.1.4.1.164.12.2.1.2.1.1.1.2
The counter associated with the number of transmitted cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpCurrentRxCellsClp0		1.3.6.1.4.1.164.12.2.1.2.1.1.1.3
The counter associated with the number of received cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpCurrentGcra0Violations		1.3.6.1.4.1.164.12.2.1.2.1.1.1.4
The counter associated with the number of cells violating GCRA0, encountered by the VPL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpCurrentGcra1Violations		1.3.6.1.4.1.164.12.2.1.2.1.1.1.5
The counter associated with the number of cells violating GCRA1, encountered by the VPL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpCurrentRxAIS		1.3.6.1.4.1.164.12.2.1.2.1.1.1.6
The counter associated with the number of received AIS cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpCurrentTxAIS		1.3.6.1.4.1.164.12.2.1.2.1.1.1.7
The counter associated with the number of transmitted AIS cells, encountered by the VPL of this ATM interface in the current 15 minute interval. Not Supported in the first phase.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpCurrentRxRDI		1.3.6.1.4.1.164.12.2.1.2.1.1.1.8
The counter associated with the number of received RDI cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpCurrentTxRDI		1.3.6.1.4.1.164.12.2.1.2.1.1.1.9
The counter associated with the number of transmitted RDI cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpCurrentContinuityLoss		1.3.6.1.4.1.164.12.2.1.2.1.1.1.10
The counter associated with the number of loss of continuity cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpCurrentUAS		1.3.6.1.4.1.164.12.2.1.2.1.1.1.11
The counter associated with the number of Unavailable Seconds, encountered by the VPL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpCurrentSES		1.3.6.1.4.1.164.12.2.1.2.1.1.1.12
The counter associated with the number of Severerly Errored Seconds, encountered by the VPL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpCurrentCDC		1.3.6.1.4.1.164.12.2.1.2.1.1.1.13
Amount of cells dropped in the current 15 minute interval of the VP connection.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpCurrentTotalDiscards		1.3.6.1.4.1.164.12.2.1.2.1.1.1.14
The total number of valid ATM cells discarded by the traffic policing entity. This includes cells originally received with CLP=0 and CLP=1.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpCurrentClp0Discards		1.3.6.1.4.1.164.12.2.1.2.1.1.1.15
The total number of valid ATM cells received with CLP=0 and discarded by the traffic policing entity.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpCurrentTotalCellOuts		1.3.6.1.4.1.164.12.2.1.2.1.1.1.16
The total number of valid ATM cells transmitted by this VPL. This includes both CLP=0 and CLP=1 cells.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpCurrentClp0CellOuts		1.3.6.1.4.1.164.12.2.1.2.1.1.1.17
The total number of valid ATM cells transmitted with CLP=0 by this VPL.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpCurrentTaggedOuts		1.3.6.1.4.1.164.12.2.1.2.1.1.1.18
The total number of valid ATM cells tagged by the traffic policing entity from CLP=0 to CLP=1 and transmitted by this VPL.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpCurrentPCR		1.3.6.1.4.1.164.12.2.1.2.1.1.1.19
The maximum traffic rate encountered in the last interval of the VP connection (monitored once a second).
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpCurrentSCR		1.3.6.1.4.1.164.12.2.1.2.1.1.1.20
The average traffic rate during the last interval of the VP connection.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpCurrentMCR		1.3.6.1.4.1.164.12.2.1.2.1.1.1.21
MCR - The minimum traffic rate encountered in the last interval of the VP connection (monitored once a second).
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpCurrentShaperTotalDiscards		1.3.6.1.4.1.164.12.2.1.2.1.1.1.22
The total number of cells (CLP0 and CLP1) discarded due to congestion by the traffic shaper.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpCurrentShaperClp0Discards		1.3.6.1.4.1.164.12.2.1.2.1.1.1.23
The total number of CLP0 cells discarded due to congestion by the traffic shaper.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpCurrentShaperClp1Discards		1.3.6.1.4.1.164.12.2.1.2.1.1.1.24
The total number of CLP1 cells discarded due to congestion by the traffic shaper.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpPMCurrentTable		1.3.6.1.4.1.164.12.2.1.2.1.2
The ATM VP Current table for Performance Management.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmVpPMCurrentEntry

atmVpPMCurrentEntry		1.3.6.1.4.1.164.12.2.1.2.1.2.1
An entry in the ATM VP Current table for Performance Management.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmVpPMCurrentEntry

atmVpPMCurrentVpi		1.3.6.1.4.1.164.12.2.1.2.1.2.1.1
The VPI of the VPL.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmVpPMCurrentDir		1.3.6.1.4.1.164.12.2.1.2.1.2.1.2
The direction of performance management.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	forward(2), backward(3)

atmVpPMCurrentTxClp01		1.3.6.1.4.1.164.12.2.1.2.1.2.1.3
The counter associated with the number of transmitted CLP 0+1 cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpPMCurrentTxClp0		1.3.6.1.4.1.164.12.2.1.2.1.2.1.4
The counter associated with the number of transmitted CLP 0 cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpPMCurrentRxClp01		1.3.6.1.4.1.164.12.2.1.2.1.2.1.5
The counter associated with the number of received CLP 0+1 cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpPMCurrentRxClp0		1.3.6.1.4.1.164.12.2.1.2.1.2.1.6
The counter associated with the number of received CLP 0 cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpPMCurrentErroredCells		1.3.6.1.4.1.164.12.2.1.2.1.2.1.7
The counter associated with the number of errored cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpPMCurrentLostCells		1.3.6.1.4.1.164.12.2.1.2.1.2.1.8
The counter associated with the number of lost cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpPMCurrentMisinsertedCells		1.3.6.1.4.1.164.12.2.1.2.1.2.1.9
The counter associated with the number of misinserted cells, encountered by the VPL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpPMCurrentECB		1.3.6.1.4.1.164.12.2.1.2.1.2.1.10
The counter associated with the number of ECB, encountered by the VPL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpPMCurrentSECB		1.3.6.1.4.1.164.12.2.1.2.1.2.1.11
The counter associated with the number of SECB, encountered by the VPL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpPMCurrentES		1.3.6.1.4.1.164.12.2.1.2.1.2.1.12
The counter associated with the number of Errored Seconds, encountered by the VPL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpPMCurrentSES		1.3.6.1.4.1.164.12.2.1.2.1.2.1.13
The counter associated with the number of Severely Errored Seconds, encountered by the VPL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpPMCurrentUAS		1.3.6.1.4.1.164.12.2.1.2.1.2.1.14
The counter associated with the number of Unavailable Seconds, encountered by the VPL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpPMCurrentIntervalQuality		1.3.6.1.4.1.164.12.2.1.2.1.2.1.15
If the number of errors per interval is superior to the atmNteUPLTCR value, the quality of service of the interval is declared as unacceptable.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	normal(2), unacceptable(3)

atmVpPMCurrentLastDayQuality		1.3.6.1.4.1.164.12.2.1.2.1.2.1.16
If the number of errors per 24 hours is superior to the atmNteDPLTCR value, the quality of service of the day is declared as degraded.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	normal(2), degraded(4)

atmVpIntervalTable		1.3.6.1.4.1.164.12.2.1.2.1.3
The ATM Vp Interval table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmVpIntervalEntry

atmVpIntervalEntry		1.3.6.1.4.1.164.12.2.1.2.1.3.1
An entry in the ATM Vp Interval table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmVpIntervalEntry

atmVpIntervalVpi		1.3.6.1.4.1.164.12.2.1.2.1.3.1.1
The VPI of the VPL.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmVpIntervalNumber		1.3.6.1.4.1.164.12.2.1.2.1.3.1.2
A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..96

atmVpIntervalRxCellsClp01		1.3.6.1.4.1.164.12.2.1.2.1.3.1.3
The counter associated with the number of transmitted cells , encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpIntervalRxCellsClp0		1.3.6.1.4.1.164.12.2.1.2.1.3.1.4
The counter associated with the number of received cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpIntervalGcra0Violations		1.3.6.1.4.1.164.12.2.1.2.1.3.1.5
The counter associated with the number of cells violating GCRA0, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpIntervalGcra1Violations		1.3.6.1.4.1.164.12.2.1.2.1.3.1.6
The counter associated with the number of cells violating GCRA1, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpIntervalRxAIS		1.3.6.1.4.1.164.12.2.1.2.1.3.1.7
The counter associated with the number of received AIS cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpIntervalTxAIS		1.3.6.1.4.1.164.12.2.1.2.1.3.1.8
The counter associated with the number of transmitted AIS cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals. Not supported in the first phase.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpIntervalRxRDI		1.3.6.1.4.1.164.12.2.1.2.1.3.1.9
The counter associated with the number of received RDI cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpIntervalTxRDI		1.3.6.1.4.1.164.12.2.1.2.1.3.1.10
The counter associated with the number of transmitted RDI cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpIntervalContinuityLoss		1.3.6.1.4.1.164.12.2.1.2.1.3.1.11
The counter associated with the number of Continuity Loss cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpIntervalUAS		1.3.6.1.4.1.164.12.2.1.2.1.3.1.12
The counter associated with the number of Unavailable Seconds, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpIntervalSES		1.3.6.1.4.1.164.12.2.1.2.1.3.1.13
The counter associated with the number of Severerly Errored Seconds, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpIntervalCDC		1.3.6.1.4.1.164.12.2.1.2.1.3.1.14
Amount of cells dropped in the 15 minute interval of the VP connection.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpIntervalTotalDiscards		1.3.6.1.4.1.164.12.2.1.2.1.3.1.15
The total number of valid ATM cells discarded by the traffic policing entity. This includes cells originally received with CLP=0 and CLP=1.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpIntervalClp0Discards		1.3.6.1.4.1.164.12.2.1.2.1.3.1.16
The total number of valid ATM cells received with CLP=0 an discarded by the traffic policing entity.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpIntervalTotalCellOuts		1.3.6.1.4.1.164.12.2.1.2.1.3.1.17
The total number of valid ATM cells transmitted by this VPL. This includes both CLP=0 and CLP=1 cells.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpIntervalClp0CellOuts		1.3.6.1.4.1.164.12.2.1.2.1.3.1.18
The total number of valid ATM cells transmitted with CLP=0 by this VPL.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpIntervalTaggedOuts		1.3.6.1.4.1.164.12.2.1.2.1.3.1.19
The total number of valid ATM cells tagged by the traffic policing entity from CLP=0 to CLP=1 and transmitted by this VPL.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpIntervalPCR		1.3.6.1.4.1.164.12.2.1.2.1.3.1.20
The maximum traffic rate encountered in the last interval of the VP connection (monitored once a second) encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpIntervalSCR		1.3.6.1.4.1.164.12.2.1.2.1.3.1.21
The average traffic rate during the last interval of the VP connection , encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpIntervalMCR		1.3.6.1.4.1.164.12.2.1.2.1.3.1.22
MCR - The minimum traffic rate encountered in the last interval of the VP connection (monitored once a second) encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpIntervalShaperTotalDiscards		1.3.6.1.4.1.164.12.2.1.2.1.3.1.23
The total number of cells (CLP0 and CLP1) discarded due to congestion by the traffic shaper.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpIntervalShaperClp0Discards		1.3.6.1.4.1.164.12.2.1.2.1.3.1.24
The total number of CLP0 cells discarded due to congestion by the traffic shaper.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpIntervalShaperClp1Discards		1.3.6.1.4.1.164.12.2.1.2.1.3.1.25
The total number of CLP1 cells discarded due to congestion by the traffic shaper.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpPMIntervalTable		1.3.6.1.4.1.164.12.2.1.2.1.4
The ATM Vp Interval table for Performance Management.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmVpPMIntervalEntry

atmVpPMIntervalEntry		1.3.6.1.4.1.164.12.2.1.2.1.4.1
An entry in the ATM Vp Interval table for Performance Management.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmVpPMIntervalEntry

atmVpPMIntervalVpi		1.3.6.1.4.1.164.12.2.1.2.1.4.1.1
The VPI of the VPL.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmVpPMIntervalDir		1.3.6.1.4.1.164.12.2.1.2.1.4.1.2
The direction of performance management.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	forward(2), backward(3)

atmVpPMIntervalNumber		1.3.6.1.4.1.164.12.2.1.2.1.4.1.3
A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..96

atmVpPMIntervalTxClp01		1.3.6.1.4.1.164.12.2.1.2.1.4.1.4
The counter associated with the number of transmitted CLP 0+1 cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpPMIntervalTxClp0		1.3.6.1.4.1.164.12.2.1.2.1.4.1.5
The counter associated with the number of transmitted CLP 0 cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpPMIntervalRxClp01		1.3.6.1.4.1.164.12.2.1.2.1.4.1.6
The counter associated with the number of received CLP 0+1 cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpPMIntervalRxClp0		1.3.6.1.4.1.164.12.2.1.2.1.4.1.7
The counter associated with the number of received CLP 0 cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpPMIntervalErroredCells		1.3.6.1.4.1.164.12.2.1.2.1.4.1.8
The counter associated with the number of Errored cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpPMIntervalLostCells		1.3.6.1.4.1.164.12.2.1.2.1.4.1.9
The counter associated with the number of Lost cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpPMIntervalMisinsertedCells		1.3.6.1.4.1.164.12.2.1.2.1.4.1.10
The counter associated with the number of Misinserted cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpPMIntervalECB		1.3.6.1.4.1.164.12.2.1.2.1.4.1.11
The counter associated with the number of ECBs encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpPMIntervalSECB		1.3.6.1.4.1.164.12.2.1.2.1.4.1.12
The counter associated with the number of SECBs encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpPMIntervalES		1.3.6.1.4.1.164.12.2.1.2.1.4.1.13
The counter associated with the number of Errored Seconds, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpPMIntervalSES		1.3.6.1.4.1.164.12.2.1.2.1.4.1.14
The counter associated with the number of Severely Errored Seconds, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpPMIntervalUAS		1.3.6.1.4.1.164.12.2.1.2.1.4.1.15
The counter associated with the number of Unavailable Seconds, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpPMIntervalQuality		1.3.6.1.4.1.164.12.2.1.2.1.4.1.16
If the number of errors per interval is superior to the atmNteUPLTCR value, the quality of service of the interval is declared as unacceptable.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	normal(2), unacceptable(3)

atmVpPMIntervalLastDayQuality		1.3.6.1.4.1.164.12.2.1.2.1.4.1.17
If the number of errors per 24 hours is superior to the atmNteDPLTCR value, the quality of service of the day is declared as degraded.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	normal(2), degraded(4)

atmVpQoSTable		1.3.6.1.4.1.164.12.2.1.2.1.5
The VP QoS table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmVpQoSEntry

atmVpQoSEntry		1.3.6.1.4.1.164.12.2.1.2.1.5.1
.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmVpQoSEntry

atmVpQoSPeriodRef		1.3.6.1.4.1.164.12.2.1.2.1.5.1.1
This object is an index that specifies which period of time, the next 2 objects refer to. currentPeriod - the period since last systemResetAllStatsCmd received or since Start-up (if no systemResetAllStatsCmd was received since Start-up) until now. lastPeriod - the period between last two commands of systemResetAllStatsCmd. - If only one command occurred since Start-up: the period between Start-up and last command. - If no command occurred since Start-up: this period will not actually exist. In this case, he following 5 objects will be 0.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	currentPeriod(1), lastPeriod(2)

atmVpQoSElapsedTime		1.3.6.1.4.1.164.12.2.1.2.1.5.1.2
Elapsed Time in seconds. - for atmVpQoSPeriodRef = currentPeriod: The period since last systemResetAllStatsCmd received or since Start-up (if no systemResetAllStatsCmd was received since Start-up) until now. - for atmVpQoSPeriodRef = lastPeriod: The value of atmVpQoSElapsedTime when last systemResetAllStatsCmd was received.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmVpQoSUAS		1.3.6.1.4.1.164.12.2.1.2.1.5.1.3
Number of Unavailable Seconds for the reference period (atmVpQoSPeriodRef).
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpPMQoSTable		1.3.6.1.4.1.164.12.2.1.2.1.6
The PM VP QoS table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmVpPMQoSEntry

atmVpPMQoSEntry		1.3.6.1.4.1.164.12.2.1.2.1.6.1
.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmVpPMQoSEntry

atmVpPMQoSDirection		1.3.6.1.4.1.164.12.2.1.2.1.6.1.1
The direction of performance management.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	forward(2), backward(3)

atmVpPMQoSPeriodRef		1.3.6.1.4.1.164.12.2.1.2.1.6.1.2
This object is an index that specifies which period of time, the next 5 objects refer to. currentPeriod - the period since last systemResetAllStatsCmd received or since Start-up (if no systemResetAllStatsCmd was received since Start-up) until now. lastPeriod - the period between last two commands of systemResetAllStatsCmd. - If only one command occurred since Start-up: the period between Start-up and last command. - If no command occurred since Start-up: this period will not actually exist. In this case, he following 5 objects will be 0.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	currentPeriod(1), lastPeriod(2)

atmVpPMQoSCLR		1.3.6.1.4.1.164.12.2.1.2.1.6.1.3
Cell Loss Ratio counter for the reference period (atmVpPMQoSPeriodRef)- defined in accordance with I.356 , in %. The value will be multipuled by 100.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpPMQoSCER		1.3.6.1.4.1.164.12.2.1.2.1.6.1.4
Cell Error Ratio counter for the reference period (atmVpPMQoSPeriodRef) defined in accordance with I.356 , in %. The value will be multipuled by 100.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpPMQoSCMR		1.3.6.1.4.1.164.12.2.1.2.1.6.1.5
Cell Misinsertion Ratio counter for the reference period (atmVpPMQoSPeriodRef) defined in accordance with I.356 , cells/sec .
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVpShaperStatTable		1.3.6.1.4.1.164.12.2.1.2.1.7
The ATM VP shaper statistics table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmVpShaperStatEntry

atmVpShaperStatEntry		1.3.6.1.4.1.164.12.2.1.2.1.7.1
An entry in the ATM VP shaper statistics table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmVpShaperStatEntry

atmVpShaperDiscarded		1.3.6.1.4.1.164.12.2.1.2.1.7.1.1
The number of Cells that were discarded in the shaper on that VPC due to buffer overflow. This counter counts till it reaches its MAX value (20 bits) and then rolls over.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

atmVpShaperOccupation		1.3.6.1.4.1.164.12.2.1.2.1.7.1.2
The number of Cells that are currently stored in the buffer. This parameter is limited to 20 bits.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmVpShaperMaxOccupation		1.3.6.1.4.1.164.12.2.1.2.1.7.1.3
The Maximum number of Cells that were stored in the buffer, since this VP was activated. This parameter is limited to 20 bits.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmVpShaperLevel		1.3.6.1.4.1.164.12.2.1.2.1.7.1.4
The occupation of the buffer according to a predefined threshold. empty - buffer is Empty full - buffer is Full below - buffer is Below the threshold above - buffer is Above the threshold. This is also the trigger to start EPD\PPD mechanism, if set for the VPC.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	empty(1), full(2), below(3), above(4)

atmVpShaperEpdDropped		1.3.6.1.4.1.164.12.2.1.2.1.7.1.5
The number of Cells that were dropped in the shaper on that VPC due to EPD\PPD mechanism in the last second. This parameter is limited to 24 bits. Applicable for a EPD/PPD VP only.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

atmVpShaperTotalEpdDropped		1.3.6.1.4.1.164.12.2.1.2.1.7.1.6
The Total number of Cells that were dropped in the shaper on that VPC due to EPD\PPD mechanism in the last 15 minutes. This counter automatically reset itself every 15 minutes. Applicable for a EPD/PPD VP only.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

atmVcPerformance		1.3.6.1.4.1.164.12.2.1.2.2
OBJECT IDENTIFIER

atmVcCurrentTable		1.3.6.1.4.1.164.12.2.1.2.2.1
The ATM VC Current table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmVcCurrentEntry

atmVcCurrentEntry		1.3.6.1.4.1.164.12.2.1.2.2.1.1
An entry in the ATM VC Current table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmVcCurrentEntry

atmVcCurrentVpi		1.3.6.1.4.1.164.12.2.1.2.2.1.1.1
The VPI of the VCL.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmVcCurrentVci		1.3.6.1.4.1.164.12.2.1.2.2.1.1.2
The VCI of the VCL.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmVcCurrentRxCellsClp01		1.3.6.1.4.1.164.12.2.1.2.2.1.1.3
The counter associated with the number of transmitted cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcCurrentRxCellsClp0		1.3.6.1.4.1.164.12.2.1.2.2.1.1.4
The counter associated with the number of received cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcCurrentGcra0Violations		1.3.6.1.4.1.164.12.2.1.2.2.1.1.5
The counter associated with the number of cells violating GCRA0, encountered by the VCL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcCurrentGcra1Violations		1.3.6.1.4.1.164.12.2.1.2.2.1.1.6
The counter associated with the number of cells violating GCRA1, encountered by the VCL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcCurrentRxAIS		1.3.6.1.4.1.164.12.2.1.2.2.1.1.7
The counter associated with the number of received AIS cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcCurrentTxAIS		1.3.6.1.4.1.164.12.2.1.2.2.1.1.8
The counter associated with the number of transmitted AIS cells, encountered by the VCL of this ATM interface in the current 15 minute interval. Not Supported in the first phase.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcCurrentRxRDI		1.3.6.1.4.1.164.12.2.1.2.2.1.1.9
The counter associated with the number of received RDI cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcCurrentTxRDI		1.3.6.1.4.1.164.12.2.1.2.2.1.1.10
The counter associated with the number of transmitted RDI cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcCurrentContinuityLoss		1.3.6.1.4.1.164.12.2.1.2.2.1.1.11
The counter associated with the number of loss of continuity cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcCurrentUAS		1.3.6.1.4.1.164.12.2.1.2.2.1.1.12
The counter associated with the number of Unavailable Seconds, encountered by the VCL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcCurrentSES		1.3.6.1.4.1.164.12.2.1.2.2.1.1.13
The counter associated with the number of Severerly Errored Seconds, encountered by the VCL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcCurrentCDC		1.3.6.1.4.1.164.12.2.1.2.2.1.1.14
Amount of cells dropped in the current 15 minute interval of the VC connection.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcCurrentTotalDiscards		1.3.6.1.4.1.164.12.2.1.2.2.1.1.15
The total number of valid ATM cells discarded by the traffic policing entity. This includes cells originally received with CLP=0 and CLP=1.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcCurrentClp0Discards		1.3.6.1.4.1.164.12.2.1.2.2.1.1.16
The total number of valid ATM cells received with CLP=0 an discarded by the traffic policing entity.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcCurrentTotalCellOuts		1.3.6.1.4.1.164.12.2.1.2.2.1.1.17
The total number of valid ATM cells transmitted by this VPL. This includes both CLP=0 and CLP=1 cells.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcCurrentClp0CellOuts		1.3.6.1.4.1.164.12.2.1.2.2.1.1.18
The total number of valid ATM cells transmitted with CLP=0 by this VPL.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcCurrentTaggedOuts		1.3.6.1.4.1.164.12.2.1.2.2.1.1.19
The total number of valid ATM cells tagged by the traffic policing entity from CLP=0 to CLP=1 and transmitted by this VPL.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcCurrentPCR		1.3.6.1.4.1.164.12.2.1.2.2.1.1.20
The maximum traffic rate encountered in the last interval of the VC connection (monitored once a second).
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcCurrentSCR		1.3.6.1.4.1.164.12.2.1.2.2.1.1.21
The average traffic rate during the last interval of the VC connection.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcCurrentMCR		1.3.6.1.4.1.164.12.2.1.2.2.1.1.22
MCR - The minimum traffic rate encountered in the last interval of the VC connection (monitored once a second).
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcCurrentShaperTotalDiscards		1.3.6.1.4.1.164.12.2.1.2.2.1.1.23
The total number of cells (CLP0 and CLP1) discarded due to congestion by the traffic shaper.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcCurrentShaperClp0Discards		1.3.6.1.4.1.164.12.2.1.2.2.1.1.24
The total number of CLP0 cells discarded due to congestion by the traffic shaper.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcCurrentShaperClp1Discards		1.3.6.1.4.1.164.12.2.1.2.2.1.1.25
The total number of CLP1 cells discarded due to congestion by the traffic shaper.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcPMCurrentTable		1.3.6.1.4.1.164.12.2.1.2.2.2
The ATM VC Current table for Performance Management.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmVcPMCurrentEntry

atmVcPMCurrentEntry		1.3.6.1.4.1.164.12.2.1.2.2.2.1
An entry in the ATM VC Current table for Performance Management.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmVcPMCurrentEntry

atmVcPMCurrentVpi		1.3.6.1.4.1.164.12.2.1.2.2.2.1.1
The VPI of the VCL.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmVcPMCurrentVci		1.3.6.1.4.1.164.12.2.1.2.2.2.1.2
The VCI of the VCL.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmVcPMCurrentDir		1.3.6.1.4.1.164.12.2.1.2.2.2.1.3
The direction of Performance Management.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmVcPMCurrentTxClp01		1.3.6.1.4.1.164.12.2.1.2.2.2.1.4
The counter associated with the number of transmitted CLP 0+1 cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcPMCurrentTxClp0		1.3.6.1.4.1.164.12.2.1.2.2.2.1.5
The counter associated with the number of transmitted CLP 0 cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcPMCurrentRxClp01		1.3.6.1.4.1.164.12.2.1.2.2.2.1.6
The counter associated with the number of received CLP 0+1 cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcPMCurrentRxClp0		1.3.6.1.4.1.164.12.2.1.2.2.2.1.7
The counter associated with the number of received CLP 0 cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcPMCurrentErroredCells		1.3.6.1.4.1.164.12.2.1.2.2.2.1.8
The counter associated with the number of errored cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcPMCurrentLostCells		1.3.6.1.4.1.164.12.2.1.2.2.2.1.9
The counter associated with the number of lost cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcPMCurrentMisinsertedCells		1.3.6.1.4.1.164.12.2.1.2.2.2.1.10
The counter associated with the number of misinserted cells, encountered by the VCL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcPMCurrentECB		1.3.6.1.4.1.164.12.2.1.2.2.2.1.11
The counter associated with the number of ECBs encountered by the VCL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcPMCurrentSECB		1.3.6.1.4.1.164.12.2.1.2.2.2.1.12
The counter associated with the number of SECBs encountered by the VCL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcPMCurrentES		1.3.6.1.4.1.164.12.2.1.2.2.2.1.13
The counter associated with the number of Errored Seconds, encountered by the VCL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcPMCurrentSES		1.3.6.1.4.1.164.12.2.1.2.2.2.1.14
The counter associated with the number of Severely Errored Seconds, encountered by the VCL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcPMCurrentUAS		1.3.6.1.4.1.164.12.2.1.2.2.2.1.15
The counter associated with the number of Severely Errored Seconds, encountered by the VCL of this ATM interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcPMCurrentIntervalQuality		1.3.6.1.4.1.164.12.2.1.2.2.2.1.16
If the number of errors per interval is superior to the atmNteUPLTCR value, the quality of service of the interval is declared as unacceptable.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	normal(2), unacceptable(3)

atmVcPMCurrentLastDayQuality		1.3.6.1.4.1.164.12.2.1.2.2.2.1.17
If the number of errors per 24 hours is superior to the atmNteDPLTCR value, the quality of service of the day is declared as degraded.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	normal(2), degraded(4)

atmVcIntervalTable		1.3.6.1.4.1.164.12.2.1.2.2.3
The ATM Vc Interval table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmVcIntervalEntry

atmVcIntervalEntry		1.3.6.1.4.1.164.12.2.1.2.2.3.1
An entry in the ATM Vc Interval table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmVcIntervalEntry

atmVcIntervalVpi		1.3.6.1.4.1.164.12.2.1.2.2.3.1.1
The VPI of the VCL.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmVcIntervalVci		1.3.6.1.4.1.164.12.2.1.2.2.3.1.2
The VCI of the VCL.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmVcIntervalNumber		1.3.6.1.4.1.164.12.2.1.2.2.3.1.3
A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..96

atmVcIntervalRxCellsClp01		1.3.6.1.4.1.164.12.2.1.2.2.3.1.4
The counter associated with the number of transmitted cells , encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcIntervalRxCellsClp0		1.3.6.1.4.1.164.12.2.1.2.2.3.1.5
The counter associated with the number of received cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcIntervalGcra0Violations		1.3.6.1.4.1.164.12.2.1.2.2.3.1.6
The counter associated with the number of cells violating GCRA0, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcIntervalGcra1Violations		1.3.6.1.4.1.164.12.2.1.2.2.3.1.7
The counter associated with the number of cells violating GCRA1, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcIntervalRxAIS		1.3.6.1.4.1.164.12.2.1.2.2.3.1.8
The counter associated with the number of received AIS cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcIntervalTxAIS		1.3.6.1.4.1.164.12.2.1.2.2.3.1.9
The counter associated with the number of transmitted AIS cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals. Not supported in the first phase.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcIntervalRxRDI		1.3.6.1.4.1.164.12.2.1.2.2.3.1.10
The counter associated with the number of received RDI cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcIntervalTxRDI		1.3.6.1.4.1.164.12.2.1.2.2.3.1.11
The counter associated with the number of transmitted RDI cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcIntervalContinuityLoss		1.3.6.1.4.1.164.12.2.1.2.2.3.1.12
The counter associated with the number of Continuity Loss cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcIntervalUAS		1.3.6.1.4.1.164.12.2.1.2.2.3.1.13
The counter associated with the number of Unavailable Seconds, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcIntervalSES		1.3.6.1.4.1.164.12.2.1.2.2.3.1.14
The counter associated with the number of Severerly Errored Seconds, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcIntervalCDC		1.3.6.1.4.1.164.12.2.1.2.2.3.1.15
Amount of cells dropped in the 15 minute interval of the VC connection.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcIntervalTotalDiscards		1.3.6.1.4.1.164.12.2.1.2.2.3.1.16
The total number of valid ATM cells discarded by the traffic policing entity. This includes cells originally received with CLP=0 and CLP=1.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcIntervalClp0Discards		1.3.6.1.4.1.164.12.2.1.2.2.3.1.17
The total number of valid ATM cells received with CLP=0 an discarded by the traffic policing entity.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcIntervalTotalCellOuts		1.3.6.1.4.1.164.12.2.1.2.2.3.1.18
The total number of valid ATM cells transmitted by this VPL. This includes both CLP=0 and CLP=1 cells.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcIntervalClp0CellOuts		1.3.6.1.4.1.164.12.2.1.2.2.3.1.19
The total number of valid ATM cells transmitted with CLP=0 by this VPL.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcIntervalTaggedOuts		1.3.6.1.4.1.164.12.2.1.2.2.3.1.20
The total number of valid ATM cells tagged by the traffic policing entity from CLP=0 to CLP=1 and transmitted by this VPL.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcIntervalPCR		1.3.6.1.4.1.164.12.2.1.2.2.3.1.21
The maximum traffic rate encountered in the last interval of the VC connection (monitored once a second) encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcIntervalSCR		1.3.6.1.4.1.164.12.2.1.2.2.3.1.22
The average traffic rate during the last interval of the VC connection, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcIntervalMCR		1.3.6.1.4.1.164.12.2.1.2.2.3.1.23
MCR - The minimum traffic rate encountered in the last interval of the VC connection (monitored once a second) encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcIntervalShaperTotalDiscards		1.3.6.1.4.1.164.12.2.1.2.2.3.1.24
The total number of cells (CLP0 and CLP1) discarded due to congestion by the traffic shaper.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcIntervalShaperClp0Discards		1.3.6.1.4.1.164.12.2.1.2.2.3.1.25
The total number of CLP0 cells discarded due to congestion by the traffic shaper.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcIntervalShaperClp1Discards		1.3.6.1.4.1.164.12.2.1.2.2.3.1.26
The total number of CLP1 cells discarded due to congestion by the traffic shaper.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcPMIntervalTable		1.3.6.1.4.1.164.12.2.1.2.2.4
The ATM Vc Interval table for Performance Management.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmVcPMIntervalEntry

atmVcPMIntervalEntry		1.3.6.1.4.1.164.12.2.1.2.2.4.1
An entry in the ATM Vc Interval table for Performance Management.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmVcPMIntervalEntry

atmVcPMIntervalVpi		1.3.6.1.4.1.164.12.2.1.2.2.4.1.1
The VPI of the VCL.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmVcPMIntervalVci		1.3.6.1.4.1.164.12.2.1.2.2.4.1.2
The VCI of the VCL.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmVcPMIntervalDir		1.3.6.1.4.1.164.12.2.1.2.2.4.1.3
The direction of Performance Management.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	forward(2), backward(3)

atmVcPMIntervalNumber		1.3.6.1.4.1.164.12.2.1.2.2.4.1.4
A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..96

atmVcPMIntervalTxClp01		1.3.6.1.4.1.164.12.2.1.2.2.4.1.5
The counter associated with the number of transmitted CLP 0+1 cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcPMIntervalTxClp0		1.3.6.1.4.1.164.12.2.1.2.2.4.1.6
The counter associated with the number of transmitted CLP 0 cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcPMIntervalRxClp01		1.3.6.1.4.1.164.12.2.1.2.2.4.1.7
The counter associated with the number of received CLP 0+1 cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcPMIntervalRxClp0		1.3.6.1.4.1.164.12.2.1.2.2.4.1.8
The counter associated with the number of received CLP 0 cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcPMIntervalErroredCells		1.3.6.1.4.1.164.12.2.1.2.2.4.1.9
The counter associated with the number of Errored cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcPMIntervalLostCells		1.3.6.1.4.1.164.12.2.1.2.2.4.1.10
The counter associated with the number of Lost cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcPMIntervalMisinsertedCells		1.3.6.1.4.1.164.12.2.1.2.2.4.1.11
The counter associated with the number of Misinserted cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcPMIntervalECB		1.3.6.1.4.1.164.12.2.1.2.2.4.1.12
The counter associated with the number of ECBs encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcPMIntervalSECB		1.3.6.1.4.1.164.12.2.1.2.2.4.1.13
The counter associated with the number of SECBs encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcPMIntervalES		1.3.6.1.4.1.164.12.2.1.2.2.4.1.14
The counter associated with the number of Errored Seconds, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcPMIntervalSES		1.3.6.1.4.1.164.12.2.1.2.2.4.1.15
The counter associated with the number of Severely Errored Seconds, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcPMIntervalUAS		1.3.6.1.4.1.164.12.2.1.2.2.4.1.16
The counter associated with the number of Unavailable Seconds, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcPMIntervalQuality		1.3.6.1.4.1.164.12.2.1.2.2.4.1.17
If the number of errors per interval is superior to the atmNteUPLTCR value, the quality of service of the interval is declared as unacceptable.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	normal(2), unacceptable(3)

atmVcPMIntervalLastDayQuality		1.3.6.1.4.1.164.12.2.1.2.2.4.1.18
If the number of errors per 24 hours is superior to the atmNteDPLTCR value, the quality of service of the day is declared as degraded.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	normal(2), degraded(4)

atmVcQoSTable		1.3.6.1.4.1.164.12.2.1.2.2.6
The ATM VP QoS table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmVcQoSEntry

atmVcQoSEntry		1.3.6.1.4.1.164.12.2.1.2.2.6.1
An entry in the ATM VP table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmVcQoSEntry

atmVcQoSPeriodRef		1.3.6.1.4.1.164.12.2.1.2.2.6.1.1
This object is an index that specifies which period of time, the next 2 objects refer to. currentPeriod - the period since last systemResetAllStatsCmd received or since Start-up (if no systemResetAllStatsCmd was received since Start-up) until now. lastPeriod - the period between last two commands of systemResetAllStatsCmd. - If only one command occurred since Start-up: the period between Start-up and last command. - If no command occurred since Start-up: this period will not actually exist. In this case, he following 5 objects will be 0.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	currentPeriod(1), lastPeriod(2)

atmVcQoSElapsedTime		1.3.6.1.4.1.164.12.2.1.2.2.6.1.2
Elapsed Time in seconds. - for atmVcQoSPeriodRef = currentPeriod: The period since last systemResetAllStatsCmd received or since Start-up (if no systemResetAllStatsCmd was received since Start-up) until now. - for atmVcQoSPeriodRef = lastPeriod: The value of atmVcQoSElapsedTime when last systemResetAllStatsCmd was received.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmVcQoSUAS		1.3.6.1.4.1.164.12.2.1.2.2.6.1.3
Number of Unavailable Seconds for the reference period (atmVcQoSPeriodRef).
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcPMQoSTable		1.3.6.1.4.1.164.12.2.1.2.2.7
The PM VC QoS table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmVcPMQoSEntry

atmVcPMQoSEntry		1.3.6.1.4.1.164.12.2.1.2.2.7.1
An entry in the VC PM QoS table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmVcPMQoSEntry

atmVcPMQoSDirection		1.3.6.1.4.1.164.12.2.1.2.2.7.1.1
The direction of performance management.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	forward(2), backward(3)

atmVcPMQoSPeriodRef		1.3.6.1.4.1.164.12.2.1.2.2.7.1.2
This object is an index that specifies which period of time, the next 5 objects refer to. currentPeriod - the period since last systemResetAllStatsCmd received or since Start-up (if no systemResetAllStatsCmd was received since Start-up) until now. lastPeriod - the period between last two commands of systemResetAllStatsCmd. - If only one command occurred since Start-up: the period between Start-up and last command. - If no command occurred since Start-up: this period will not actually exist. In this case, he following 5 objects will be 0.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	currentPeriod(1), lastPeriod(2)

atmVcPMQoSCLR		1.3.6.1.4.1.164.12.2.1.2.2.7.1.3
Cell Loss Ratio counter for the reference period (atmVcPMQoSPeriodRef)- defined in accordance with I.356 , in %. The value will be multipuled by 100.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcPMQoSCER		1.3.6.1.4.1.164.12.2.1.2.2.7.1.4
Cell Error Ratio counter for the reference period (atmVcPMQoSPeriodRef) defined in accordance with I.356 , in %. The value will be multipuled by 100.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcPMQoSCMR		1.3.6.1.4.1.164.12.2.1.2.2.7.1.5
Cell Miss-insertion Ratio counter for the reference period (atmVcPMQoSPeriodRef) defined in accordance with I.356 , cells/sec .
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmVcShaperStatTable		1.3.6.1.4.1.164.12.2.1.2.2.8
The ATM VC shaper statistics table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmVcShaperStatEntry

atmVcShaperStatEntry		1.3.6.1.4.1.164.12.2.1.2.2.8.1
An entry in the ATM VC shaper statistics table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmVcShaperStatEntry

atmVcShaperDiscarded		1.3.6.1.4.1.164.12.2.1.2.2.8.1.1
The number of Cells that were discarded in the shaper on that VCC due to buffer overflow. This counter counts till it reaches its MAX value (20 bits) and then rolls over.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

atmVcShaperOccupation		1.3.6.1.4.1.164.12.2.1.2.2.8.1.2
The number of Cells that are currently stored in the buffer. This parameter is limited to 20 bits.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmVcShaperMaxOccupation		1.3.6.1.4.1.164.12.2.1.2.2.8.1.3
The Maximum number of Cells that were stored in the buffer, since this VC was activated. This parameter is limited to 20 bits.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmVcShaperLevel		1.3.6.1.4.1.164.12.2.1.2.2.8.1.4
The occupation of the buffer according to a predefined threshold. empty - buffer is Empty full - buffer is Full below - buffer is Below the threshold above - buffer is Above the threshold. This is also the trigger to start EPD\PPD mechanism, if set for the VCC.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	empty(1), full(2), below(3), above(4)

atmVcShaperEpdDropped		1.3.6.1.4.1.164.12.2.1.2.2.8.1.5
The number of Cells that were dropped in the shaper on that VCC due to EPD\PPD mechanism in the last second. This parameter is limited to 24 bits. Applicable for a EPD/PPD VC only.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

atmVcShaperTotalEpdDropped		1.3.6.1.4.1.164.12.2.1.2.2.8.1.6
The Total number of Cells that were dropped in the shaper on that VPC due to EPD\PPD mechanism in the last 15 minutes. This counter automatically reset itself every 15 minutes. Applicable for a EPD/PPD VC only.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

atmIntervalDateTable		1.3.6.1.4.1.164.12.2.1.3
The agent will keep in this group the date & time corresponding to each interval.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmIntervalDateEntry

atmIntervalDateEntry		1.3.6.1.4.1.164.12.2.1.3.1
The date & time for the given interval.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmIntervalDateEntry

atmIntervalDateInterval		1.3.6.1.4.1.164.12.2.1.3.1.1
The interval number defining this entry.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..96

atmIntervalDateDate		1.3.6.1.4.1.164.12.2.1.3.1.2
The date corresponding to this interval.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

atmIntervalDateTime		1.3.6.1.4.1.164.12.2.1.3.1.3
The time corresponding to this interval.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

atmNteSys		1.3.6.1.4.1.164.12.3.1
OBJECT IDENTIFIER

atmNteSysConfig		1.3.6.1.4.1.164.12.3.1.1
OBJECT IDENTIFIER

atmNteManagerTable		1.3.6.1.4.1.164.12.3.1.1.1
The Manager Table includes all the NMSs that receive traps from this agent. A single manager can receive traps on more than one PVC. The agent will set implicitly the correct ifIndex, VPI, VCI values to all relevant entries in the table when the user changes them for one of the PVCs.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmNteManagerEntry

atmNteManagerEntry		1.3.6.1.4.1.164.12.3.1.1.1.1
A single manager and the PVC for receiving traps.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmNteManagerEntry

atmNteManagerIP		1.3.6.1.4.1.164.12.3.1.1.1.1.1
The IP address of the NMS.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

atmNteManagerPvc		1.3.6.1.4.1.164.12.3.1.1.1.1.2
A PVC index. The range is 1..8. There are four PVCs on the User Port and four PVCs on the Network Port. The default VPI, VCI values are specified below.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmNteManagerIfIndex		1.3.6.1.4.1.164.12.3.1.1.1.1.3
The ATM interface index of the management port.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

atmNteManagerVpi		1.3.6.1.4.1.164.12.3.1.1.1.1.4
The VPI of the management VCL. Default: 0.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

atmNteManagerVci		1.3.6.1.4.1.164.12.3.1.1.1.1.5
The VCI of the management VCL. Defaults: 32,33,34,35.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

atmNteManagerTrapMask		1.3.6.1.4.1.164.12.3.1.1.1.1.6
The value of this attribute determines the type of traps the agent should mask and not send to this NMS. The value is differently determined for different products. There are mainly two methods: - an integer number, specifying the traps' severity. - a sum of 2**n, where n is a bit assigned to a certain masked trap group. User should consult the product specification, to find out the method employed.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

atmNteManagerRowStatus		1.3.6.1.4.1.164.12.3.1.1.1.1.7
Creation/Deletion of rows in the table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

atmNteManagerNextHop		1.3.6.1.4.1.164.12.3.1.1.1.1.8
This parameter is relevant to Ethernet out of band host only (PVC=10). The Next Hop IP address of the entry route.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

atmNteManagerVlanSupport		1.3.6.1.4.1.164.12.3.1.1.1.1.9
VLAN support (Tagging). no - No support to VLAN. yes - 4 VLAN bytes will be added to the frame.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	no(2), yes(3)

atmNteManagerVlanIdentifier		1.3.6.1.4.1.164.12.3.1.1.1.1.10
VLAN ID. Range is 0..4095.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

atmNteManagerVlanFramePriority		1.3.6.1.4.1.164.12.3.1.1.1.1.11
VLAN Frame priority.Range is 0..7.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

atmNteManagerAlarmTrapMask		1.3.6.1.4.1.164.12.3.1.1.1.1.12
The value of this object determines the alarm traps that the agent should mask and not send to this NMS. The value is an Octet String, where each bit is assigned to a certain trap. If the bit = 1, the trap will be masked. If the bit = 0, the trap will not be masked. More details on the masked traps exist in the product specification. For products that do not mask specific traps, the value of the bits will be 0.
Status: current	Access: read-create
OBJECT-TYPE
	OCTET STRING

atmNteManagerConfigPorts		1.3.6.1.4.1.164.12.3.1.1.1.1.13
This variable defines from which port/s this manager can configure the device. For IPmux 11 the value of this variable will be according to the ports combination: Network =1 User1=2 User2=4 (For Example: All ports = 7).
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

atmNteUPLTCR		1.3.6.1.4.1.164.12.3.1.1.2
The Unacceptable ES Limit threshold for Performance Management.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmNteDPLTCR		1.3.6.1.4.1.164.12.3.1.1.3
The Degraded ES Limit threshold for Performance Management.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmNteSysLogClearAll		1.3.6.1.4.1.164.12.3.1.1.4
Setting the variable to clear(3) removes all entries in the Log Buffer of the agent. The agent will immediately reset the variable to off(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), clear(3)

atmNteUSESLTCR		1.3.6.1.4.1.164.12.3.1.1.5
The Unacceptable SES Limit threshold for Performance Management.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmNteDSESLTCR		1.3.6.1.4.1.164.12.3.1.1.6
The Degraded ES Limit threshold for Performance Management.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmNteProtection		1.3.6.1.4.1.164.12.3.1.1.8
OBJECT IDENTIFIER

atmNteProtectionMode		1.3.6.1.4.1.164.12.3.1.1.8.1
Protection Mode. MspOn - Multiplex section protection. pathOn - High order path protection. mspUniOn - Multiplex section Uni-directional protection. mspOneToN - Multiplex section protection.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(1), mspOn(2), pathOn(3), mspUniOn(4), mspOneToN(5)

atmNteProtectionWorkingLink		1.3.6.1.4.1.164.12.3.1.1.8.2
Selects the working link when atmNteProtectionMode is off.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	trunk1(2), trunk2(3)

atmNteProtectionSwitchLink		1.3.6.1.4.1.164.12.3.1.1.8.3
ForceSwitch - will force Switching from the working link to the backup link. Afterwards the agent will set atmNteProtectionSwitchLink back to off(1). atmNteProtectionMode must be either mspOn or pathOn.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(1), forceSwitch(2)

atmNteConfOam		1.3.6.1.4.1.164.12.3.1.1.9
OBJECT IDENTIFIER

atmNteConfOamSupport		1.3.6.1.4.1.164.12.3.1.1.9.1
OAM support mode, which determines the device location in a segment wise.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	intermediate(1), segmentTermination(2), endToEndTermination(3), vpEndToEndVcSegment(4)

atmNteConfOamTransmission		1.3.6.1.4.1.164.12.3.1.1.9.2
OBJECT IDENTIFIER

atmNteConfOamAIS		1.3.6.1.4.1.164.12.3.1.1.9.2.1
Defines if a F4 segment OAM cell is transmitted due to problems in the other port, i.e. physical layer alarm or F4 defect. This is valid only when the ACE101 has ATM UNI interfaces in both sides and is configured for 'Non-Intrusive' mode. none - AIS is not sent to any of the ports. user - F4 AIS will be sent toward the user when defect is detected in the network port. network - F4 AIS will be sent toward the network when defect is detected in the user port. both - F4 AIS will be sent toward the network when defect is detected in the user port and toward the user when defect is detected in the network port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), user(2), network(3), both(4)

atmNteConfOamRDI		1.3.6.1.4.1.164.12.3.1.1.9.2.2
Defines if an F4 OAM RDI cell is transmitted due to physical layer problems in the port (in addition to F4 RDI cells transmitted due to ATM layer problems). The type of F4 RDI (Segment or End-to-End) is according to the ACE-101 OAM mode. For example, If it is enabled for Network port, then physical layer defect will initiate the transmission of F4 RDI cell back to the trunk.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), user(2), network(3), both(4)

atmNteConfOamAddressing		1.3.6.1.4.1.164.12.3.1.1.9.3
OBJECT IDENTIFIER

atmNteConfLoopbackAddMode		1.3.6.1.4.1.164.12.3.1.1.9.3.1
Loopback addressing mode. on - will enable loopback addressing. off - will disable loopback addressing.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(1), on(2)

atmNteConfLoopbackSourceAdd		1.3.6.1.4.1.164.12.3.1.1.9.3.2
Loopback source address. This field is relevant when atmNteConfOamAddMode is on.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(2..20)

atmNteConfOamIfTable		1.3.6.1.4.1.164.12.3.1.1.9.4
OAM support per ATM interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmNteConfOamIfEntry

atmNteConfOamIfEntry		1.3.6.1.4.1.164.12.3.1.1.9.4.1
.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmNteConfOamIfEntry

atmNteConfOamIfAisRdi		1.3.6.1.4.1.164.12.3.1.1.9.4.1.1
This parameter controls the generation of F4/F5 AIS and RDI due to lower order problems such as physical layer problems. For AIS: Defines if F4/F5 AIS cell is transmitted due to problems such as physical layer alarm or F4/F5 defect. This is applicable for all ports . off - Problems in this port will not trigger F4/F5 AIS transmition to the ajacent port (e.g. from USER to NETWORK) of a VPC/VCC. on - Problems in this port will trigger F4/F5 AIS transmition to the ajacent port (e.g. from USER to NETWORK) of a VPC/VCC. For RDI: Defines if F4/F5 RDI cell will be transmitted due to physical layer problems in that port (in addition to F4/F5 RDI cells transmitted due to ATM layer problems). For example, If it is enabled for Network port, then physical layer defect will initiate the transmission of F4/F5 RDI cell back to the trunk. The type of F4/F5 (Segment or End-to-End) is according to the configuration of the VPC/VCC.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(1), on(2)

atmNteConfCAC		1.3.6.1.4.1.164.12.3.1.1.10
OBJECT IDENTIFIER

atmNteConfCACMode		1.3.6.1.4.1.164.12.3.1.1.10.1
CAC support mode. For ACE2002, the following are the applicable values: disable(1), enable(2), 10 - 1000.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

atmNteHostIfTable		1.3.6.1.4.1.164.12.3.1.1.11
Host IP interface table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmNteHostIfEntry

atmNteHostIfEntry		1.3.6.1.4.1.164.12.3.1.1.11.1
.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmNteHostIfEntry

atmNteHostPvcIndex		1.3.6.1.4.1.164.12.3.1.1.11.1.1
A PVC index. The range is 1..10.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmNteHostIP		1.3.6.1.4.1.164.12.3.1.1.11.1.2
The host interface IP address.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

atmNteHostMask		1.3.6.1.4.1.164.12.3.1.1.11.1.3
The host interface subnet mask.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

atmNteHostAtmIfIndex		1.3.6.1.4.1.164.12.3.1.1.11.1.4
ATM interface index. Will be 1 for user port, and 2 for network port.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

atmNteHostVpi		1.3.6.1.4.1.164.12.3.1.1.11.1.5
VPI of the PVC connected to that host interface.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

atmNteHostVci		1.3.6.1.4.1.164.12.3.1.1.11.1.6
VCI of the PVC connected to that host interface.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

atmNteHostRowStatus		1.3.6.1.4.1.164.12.3.1.1.11.1.7
Creation/Deletion of rows in the table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

atmNteHostRdnVpi		1.3.6.1.4.1.164.12.3.1.1.11.1.8
The VPI of the redundant management VCL. This parameter is applicable only if atmNteRdnManagement=enable(3).
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

atmNteHostRdnVci		1.3.6.1.4.1.164.12.3.1.1.11.1.9
The VCI of the redundant management VCL. This parameter is applicable only if atmNteRdnManagement=enable(3).
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

atmNteHostDefaultNextHop		1.3.6.1.4.1.164.12.3.1.1.11.1.10
The host interface Default Next Hop address. This address will be used as default next hop for every Bundle mapped to this Host.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

atmNteHostVlanTagging		1.3.6.1.4.1.164.12.3.1.1.11.1.11
VLAN Tag support. no - No support to VLAN. yes - 4 VLAN bytes will be added to each frame connected to this Host.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	no(2), yes(3)

atmNteHostDefaultVlanID		1.3.6.1.4.1.164.12.3.1.1.11.1.12
Default VLAN ID of this Host.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

atmNteHostDefaultVlanPriority		1.3.6.1.4.1.164.12.3.1.1.11.1.13
Default VLAN priority for this Host.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

atmNteShaperMode		1.3.6.1.4.1.164.12.3.1.1.12
Shaper Mode. vpInbandMng - Vcc within a Vp for management.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	normal(1), group(2), aggregate(3), vpInbandMng(4)

atmNteOutputRate		1.3.6.1.4.1.164.12.3.1.1.13
Aggregate shaping output rate in Cells per Seconds units. Default value is the Network port rate.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmNteTosMode		1.3.6.1.4.1.164.12.3.1.1.14
TOS Mode.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), enable(3)

atmNteTosMask		1.3.6.1.4.1.164.12.3.1.1.15
This parameter determines the seqence of bits that will be used for TOS. For ACE101 this parameter is applicable only if atmNteTosMode = enable. Valid only for IP-TOS process.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(1)

atmNteTosHighPriority		1.3.6.1.4.1.164.12.3.1.1.16
Priorities options are High or Low. High priority will be represented by bit = 1. Low priority will be represented by bit = 0. Each TOS value will be represented by the bit location. For example, the string for TOS 2, 9, 15 with High priority, will be: |0000 0000|... ...|0000 0000|1000 0010|0000 0100| ...98 7654 3210 (Bit #) 8 ... 3 2 1 (Byte #).
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(8)

atmNtePlugAndPlayActivity		1.3.6.1.4.1.164.12.3.1.1.17
Activity control for Manager Plug And Play. disable - disable the feature. offline - Automatic learn IP address into offline memory. online - Automatic learn IP address into online memory.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), offline(2), online(3)

atmNteSlotUsage		1.3.6.1.4.1.164.12.3.1.1.18
Applicable to ace2002. Slot 2 might be configured as user slot or as network slot.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), user(2), network(3)

atmNteConnectionsMaxNumber		1.3.6.1.4.1.164.12.3.1.1.19
The MAX number of connections supported by system. Setting this parameter will affect the number of MAX intervals supported. This parameter will affect the system only after reset. Changing this parameter from high value to a low value, will be accepted by agent only if the actual used connection <= the desired connection Max number. Applicable to ace2002.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), max1024(2), max2048(3)

atmNteDefaultVpi		1.3.6.1.4.1.164.12.3.1.1.20
Default Vpi for management.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmNteDefaultVci		1.3.6.1.4.1.164.12.3.1.1.21
Default Vci for management.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmNteReservedVpi		1.3.6.1.4.1.164.12.3.1.1.22
Internal use VPI, where shaperMode=vpInbandMng.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..255

atmNteRdnManagement		1.3.6.1.4.1.164.12.3.1.1.23
The redundancy management status.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(2), enabled(3)

atmNtePlugAndPlayIfIndex		1.3.6.1.4.1.164.12.3.1.1.24
The ifIndex of the Plug and Play VCC.
Status: current	Access: read-write
OBJECT-TYPE
	InterfaceIndex

atmNteLoopbackTimeout		1.3.6.1.4.1.164.12.3.1.1.25
The Loopback state timeout in minutes. A value of zero means no timeout (for ever). Default is 5 min.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmNteOamTable		1.3.6.1.4.1.164.12.3.1.1.26
This table is a static table, which is created by agent once upon initialization. The created entries are actually, only the supported OAM features. This table enables addition of new features by adding new entries rather than adding scalar parameters. An OAM feature is defined by the indexes values combination.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmNteOamEntry

atmNteOamEntry		1.3.6.1.4.1.164.12.3.1.1.26.1
An entry in the OAM table. Each entry in this table will indicate a special OAM.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmNteOamEntry

atmNteOamMode		1.3.6.1.4.1.164.12.3.1.1.26.1.1
The OAM cell path. endToEnd(1) - the entire path.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	endToEnd(1)

atmNteOamCellType		1.3.6.1.4.1.164.12.3.1.1.26.1.2
This object indicates a unique Indication Signal. aisAndRdi(1) - Alarm Indication Signal (AIS) and Remote Defect Indication (RDI) cell. loopback(2) - Loopback cell.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	aisAndRdi(1), loopback(2)

atmNteOamLevel		1.3.6.1.4.1.164.12.3.1.1.26.1.3
The level of the OAM cell. -- f4 (2) - VP level, f5 (3) - VC level.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	f5(3)

atmNteOamEnable		1.3.6.1.4.1.164.12.3.1.1.26.1.4
This parameter determines if the specified OAM cells will be enabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(2), enable(3)

atmNteDefaultLoopbackThreshold		1.3.6.1.4.1.164.12.3.1.1.27
The Default OAM Loopback Failure Threshold value that will be used for configuration.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmNteMaxBurstSize		1.3.6.1.4.1.164.12.3.1.1.28
The Maximum allowed burst size (cell units). This object is applicable for each Physical port.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmNteGranularityFactor		1.3.6.1.4.1.164.12.3.1.1.29
This parameter affects the granularity of the guaranteed Rate (SCR+MCR) in spaced connection (cell/sec units). It is also defines the minimum guaranteed rate in spaced connection.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmNteTotalInputRate		1.3.6.1.4.1.164.12.3.1.1.30
This parameter indicates the total input rate of the device in cells/sec.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmNteTotalOutputRate		1.3.6.1.4.1.164.12.3.1.1.31
This parameter indicates the total output rate of the device in cells/sec.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmAlarmForwardingTable		1.3.6.1.4.1.164.12.3.1.1.32
The Alarm Forwarding Mechanism will be operated for this table entries.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmAlarmForwardingEntry

atmAlarmForwardingEntry		1.3.6.1.4.1.164.12.3.1.1.32.1
Each entry in this table is a pair of ports that the Alarm Forwarding Mechanism is determined for.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmAlarmForwardingEntry

atmAlarmForwardingFailPort		1.3.6.1.4.1.164.12.3.1.1.32.1.1
An Index of the port on which a fail occurs.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

atmAlarmForwardingToPort		1.3.6.1.4.1.164.12.3.1.1.32.1.2
An Index of the port that will be affected upon the failure of the atmAlarmForwardingFailPort.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

atmAlarmForwardingRowStatus		1.3.6.1.4.1.164.12.3.1.1.32.1.3
Creation/Deletion of rows in the table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

atmAlarmForwardingFailureLevel		1.3.6.1.4.1.164.12.3.1.1.32.1.4
This parameter determines the level of failure that will operate the Alarm Forwarding Mechanism.
Status: current	Access: read-create
OBJECT-TYPE
	BITS	physical(0), atm(1)

atmAlarmForwardingRecoveryMode		1.3.6.1.4.1.164.12.3.1.1.32.1.5
This parameter determines the Recovery Mode. manual - The user should stop the RDI transmission by using the atmAlarmForwardingRecoveryCommand. automatic - The RDI transmission will be automatically stopped upon atmAlarmForwardingFailPort recovery.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	manual(1), automatic(2)

atmAlarmForwardingRecoveryCommand		1.3.6.1.4.1.164.12.3.1.1.32.1.6
This parameter is a command. It is applicable when atmAlarmForwardingRecoveryMode = manual. on - Will stop the RDI transmission. After setting to 'On' the agent will set this parameter back to 'Off'.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	off(2), on(3)

atmAlarmForwardingTimeFilterWindow		1.3.6.1.4.1.164.12.3.1.1.32.1.7
This parameter determines the Time Filter Window, meaning: how much time (in seconds) should the alarm exist in order to start the Alarm Forwarding operation.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

atmSysConfigCellTest		1.3.6.1.4.1.164.12.3.1.1.33
OBJECT IDENTIFIER

atmSysConfigCellTestPort		1.3.6.1.4.1.164.12.3.1.1.33.1
An Index of the port on which the cell test will be sent.
Status: current	Access: read-write
OBJECT-TYPE
	InterfaceIndex

atmSysConfigCellTestVpi		1.3.6.1.4.1.164.12.3.1.1.33.2
The VPI on which the cell test will be sent.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmSysConfigCellTestVci		1.3.6.1.4.1.164.12.3.1.1.33.3
The VCI on which the cell test will be sent.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atmSysConfigCellTestPti		1.3.6.1.4.1.164.12.3.1.1.33.4
The cell type.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	user(1), oamSegment(2), oamEndToEnd(3)

atmSysConfigCellTestClp		1.3.6.1.4.1.164.12.3.1.1.33.5
The type of the Cell.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	clp0(1), clp1(2)

atmSysConfigCellTestOamType		1.3.6.1.4.1.164.12.3.1.1.33.6
The OAM type of the Cell. This object is applicable if atmSysConfigCellTestPti = oamSegment/oamEndToEnd .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ais(1), rdi(2), cc(3), lb(4)

atmSysConfigCellTestPayload		1.3.6.1.4.1.164.12.3.1.1.33.7
The payload of the cell. For OAM cell the payload is set automatically to 6A.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(1)

atmSysConfigCellTestQuantity		1.3.6.1.4.1.164.12.3.1.1.33.8
Quantity of cells to send.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..10000

atmSysConfigCellTestSendCmd		1.3.6.1.4.1.164.12.3.1.1.33.9
Setting the variable to send(3) perfroms cell test. The agent will immediately reset the variable to off(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), send(3)

atmVpCrossConnectExtenTable		1.3.6.1.4.1.164.12.3.1.1.34
An extension to the ATM VP Cross Connect table (RFC2515 - atmVpCrossConnectTable).
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmVpCrossConnectExtenEntry

atmVpCrossConnectExtenEntry		1.3.6.1.4.1.164.12.3.1.1.34.1
An entry in the table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmVpCrossConnectExtenEntry

atmVpCrossConnectName		1.3.6.1.4.1.164.12.3.1.1.34.1.1
The Connection's name.
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString	Size(1..64)

atmVcCrossConnectExtenTable		1.3.6.1.4.1.164.12.3.1.1.35
An extension to the ATM VC Cross Connect table (RFC2515 - atmVcCrossConnectTable).
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmVcCrossConnectExtenEntry

atmVcCrossConnectExtenEntry		1.3.6.1.4.1.164.12.3.1.1.35.1
An entry in the table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmVcCrossConnectExtenEntry

atmVcCrossConnectName		1.3.6.1.4.1.164.12.3.1.1.35.1.1
The Connection's name.
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString	Size(1..64)

atmNteQosMode		1.3.6.1.4.1.164.12.3.1.1.37
This variable defines the QoS Mode. disable(1) - QoS is disabled. multipleVc(2) - QoS is enabled and multiple VCs can be bound per bridge port. singleVc(3) - QoS is enabled and only single VC can be bound per bridge port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), multipleVc(2), singleVc(3)

atmTrafficDescrParamXTable		1.3.6.1.4.1.164.12.3.1.1.38
An Augment to ATM Traffic Descriptor Parameter Table (atmTrafficDescrParamTable in ATM-MIB; RFC-2515).
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmTrafficDescrParamXEntry

atmTrafficDescrParamXEntry		1.3.6.1.4.1.164.12.3.1.1.38.1
An entry in the table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmTrafficDescrParamXEntry

atmTrafficDescrParamMode		1.3.6.1.4.1.164.12.3.1.1.38.1.1
The Mode of the Traffic Descriptor.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	scheduling(1), schedulingAndShaping(2), policing(3)

atmNteSysInfo		1.3.6.1.4.1.164.12.3.1.2
OBJECT IDENTIFIER

atmNteIdTable		1.3.6.1.4.1.164.12.3.1.2.1
The IDs of the cards and of the system.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmNteIdEntry

atmNteIdEntry		1.3.6.1.4.1.164.12.3.1.2.1.1
.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmNteIdEntry

atmNteIdIndex		1.3.6.1.4.1.164.12.3.1.2.1.1.1
An Index of the Unit ID table. The following units have IDs in this table: 1 - System 2 - ATM Board 3 - User Card 4 - Trunk 1 card 5 - Trunk 2 card 6 - Shaper 7 - Clock Unit 8 - Slot 1 card 9 - Slot 2 card 10 - Slot 3 card 11 - Slot 4 card 12 - Fan1 13 - Fan2 14 - Control Unit.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmNteUnitId		1.3.6.1.4.1.164.12.3.1.2.1.1.2
The ID of the Unit. For index = 6, the id will describe the validity of a shaper in the system: 0 - Shaper Not exist 1 - Shaper exist. For index = 7, the id will describe the validity of a clock in the system: 0 - Clock Not exist 1 - Clock exist. 2- Clock exist but failed. For index = 12,13 the id will describe the functionality of a FAN1 : 0 - OK 1 - Failed.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmNteUnitVersion		1.3.6.1.4.1.164.12.3.1.2.1.1.3
Hardware and Software version of the module.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

atmNteCardType		1.3.6.1.4.1.164.12.3.1.2.1.1.4
The card type.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), sc13mR155(2), st13sR155(3), st13lR155(4), utpR155(5), cxBncR155(6), e3(7), t3(8), e1(9), e1Ltu(10), fc13lR155(11), fc13lhR155(12), fc15lhR155(13), fc13lE3(14), fc13lhE3(15), fc15lhE3(16), fc13lT3(17), fc13lhT3(18), fc15lhT3(19), t1(20), eth(21), ethE1CesBnc(22), ethE1CesRj45(23), ethT1CesRj45(24), e1CesRj45(25), e1CesBnc(26), t1CesRj45(27), e14Ces(28), e14CesRj45(29), t14CesRj45(30), hdlc4port(31), hdlcE14CesBnc(32), hdlcE14CesRj45(33), hdlcT14CesRj45(34), e1Rj45(35), e1Bnc(36), ethE14CesBnc(37), ethE14CesRj45(38), ethT14CesRj45(39), hdlc1portHssi(40), hdlcHssiE14CesBnc(41), hdlcHssiE14CesRj45(42), hdlcHssiT14CesRj45(43), e14ImaRj45(44), e14ImaBnc(45), t14ImaRj45(46), ethE3CesBnc(47), ethT3CesBnc(48), smSf1R155(49), smSf2R155(50), sc13sR155(51), sc13lR155(52), utp25(53), sc13lhR155(54), sc15lhR155(55), sc13ljR155(56), sc13lhjR155(57), sc15lhjR155(58), e18Ces(59), e18CesRj45(60), t18CesRj45(61), sc13mR622(62), sc13lR622(73), sc13lhR622(74), sc15lhR622(75), fr4Port(76), t3j(77), fr1Port(78), hdlc1Port(79), sc13mR155D(80), sc13lR155D(81), fc13lR155D(82), st13lR155D(83), sc13lhR155D(84), fc13lhR155D(85), st13lhR155D(86), e18ImaBnc(87), e18ImaRj45(88), t18ImaRj45(89), lanUtpE(90), lanLc13lE(91), lanLc13mE(92), e14ImaRj45CfgMode(93), e14ImaBncCfgMode(94), t14ImaRj45CfgMode(95), sc13mR155R(96), sc13lR155R(97), fc13lR155R(98), st13lR155R(99), sc13lhR155R(100), fc13lhR155R(101), st13lhR155R(102), fEthUtpD(103), fEthSmD(104), fEthMmD(105), e14CesRj45Unbal(106), sc13mR155n(107), sc13lR155n(108), sc13lhR155n(109), sc15lhR155n(110), fc13lR155n(111), fc13lhR155n(112), fc15lhR155n(113), st13lR155n(114), lanUtp(115), lanLc13l(116), lanLc13m(117), e1FrHdlc(118), e1FrHdlcUnbal(119), t1FrHdlc(120), channelizedT3(121), fc15lhR155D(122), sc15lhR155D(123), smSf1R155D(124), smSf2R155D(125), smSf3R155D(126), fc15lhR155R(127), sc15lhR155R(128), smSf1R155R(129), smSf2R155R(130), smSf3R155R(131), st13lhR155n(132), smSf1R155n(133), smSf2R155n(134), smSf3R155n(135), t18CesNg(136), e18CesUnbalNg(137), e18CesBalNg(138), t14CesNg(139), e14CesUnbalNg(140), e14CesBalNg(141), t18ImaUniNg(142), e18ImaUniUnbalNg(143), e18ImaUniBalNg(144), t14ImaUniNg(145), e14ImaUniUnbalNg(146), e14ImaUniBalNg(147), t1Ces(148), e1CesUnbal(149), e1CesBal(150), switchedLan(151), channelizedSts1(152), st13mR155(153), st13lhR155(154), st15lhR155(155), gigabitEthUtp(156), gigabitEthSfp(157), fastEthUtp(158), fourStm1oc3SingleGbe(159), main8Atm155TwoEth(249), mainChannelized155(250), main(251), control(252), fan(253), unknown(254), empty(255)

atmNteCardStatus		1.3.6.1.4.1.164.12.3.1.2.1.1.5
Status of the card in the selected slot. notActive - Connections are in NotReady state. No configuration is available for the card. The access to the card HW is blocked. This state is relevant for an extracted card, and for a case in which the card was deactivated. active - The module installed and functions. A card that in this state can be configured. inProgress - The status during proccessing of a command from atmNteCardCmd. empty - No information is valid for the selected slot. This status is relevant to a case in which the card configaration was deleted, or in case in which a slot was empty since the device startup.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), notActive(2), active(3), inProgress(4), empty(5)

atmNteCardCmd		1.3.6.1.4.1.164.12.3.1.2.1.1.6
Command on the card that is installed in the selected slot. The commands are applicable according to the value of atmNteCardStatus. See the specification document for details. deleteConfig - Deletes the card configuration. deactivate - All the connections state will be changed to NotReady. The card configuration will be blocked. activate - Does the same as done upon card insertion: Initiates the relevant parameters, activates the physical layer, ATM layer and logical layer.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), deleteConfig(2), deactivate(3), activate(4)

atmNteProgCardType		1.3.6.1.4.1.164.12.3.1.2.1.1.7
The programmed card type.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	fourStm1oc3SingleGbe(159), main8Atm155TwoEth(249), mainChannelized155(250), main(251), control(252), fan(253), empty(255), atm155(1001), eth(1002), channelized155(1003)

atmSysPSunits		1.3.6.1.4.1.164.12.3.1.2.2
The number of power supply units.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSysPSunitsInUse		1.3.6.1.4.1.164.12.3.1.2.3
The main power supply in this unit.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ps1(2), ps2(3)

atmSysFanUnits		1.3.6.1.4.1.164.12.3.1.2.4
The number of fan units.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSysNetPrts		1.3.6.1.4.1.164.12.3.1.2.5
The number of network ports.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmSysNetPrtInUse		1.3.6.1.4.1.164.12.3.1.2.6
The network port in use.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	trunk1(2), trunk2(3)

atmNteBridgingMode		1.3.6.1.4.1.164.12.3.1.2.7
Bridging mode can be one of the following: ATM <> Ethernet - Bridging is between the Ethernet port and the ATM port (there is no bridging between VCs). ATM <> Ethernet + ATM - Bridging is done both between the Ethernet port and the ATM port and also between VCs.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	accessOnly(1), accessAndSwitching(2)

atmSysStats		1.3.6.1.4.1.164.12.3.1.2.8
OBJECT IDENTIFIER

atmSysCurrentCdc		1.3.6.1.4.1.164.12.3.1.2.8.1
Seconds in which cells dropped was occured in the current 15 minutes interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmSysIntervalTable		1.3.6.1.4.1.164.12.3.1.2.8.2
The system level Interval table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmSysIntervalEntry

atmSysIntervalEntry		1.3.6.1.4.1.164.12.3.1.2.8.2.1
.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmSysIntervalEntry

atmSysIntervalNumber		1.3.6.1.4.1.164.12.3.1.2.8.2.1.1
A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..96

atmSysIntervalCdc		1.3.6.1.4.1.164.12.3.1.2.8.2.1.2
Seconds in which cells dropped was occured in 15 minutes interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmNteEventType		1.3.6.1.4.1.164.12.3.1.2.9
This parameter identifies the event. On - the problem exist. Off - the problem not exist. InvalidLogin - Invalid login on local console. CorrectLogin - Successful login operation.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ps1NotActive(3), ps1Active(4), ps2NotActive(5), ps2Active(6), heatAlarmOff(7), heatAlarmOn(8), inputAlarm1Off(9), inputAlarm1On(10), inputAlarm2Off(11), inputAlarm2On(12), inputAlarm3Off(13), inputAlarm3On(14), inputAlarm4Off(15), inputAlarm4On(16), fan1Ok(17), fan1Fail(18), fan2Ok(19), fan2Fail(20), invalidLogin(21), validLogin(22), powerFailure(23), writeToFlashFailure(24)

atmNteIntervalMaxNumber		1.3.6.1.4.1.164.12.3.1.2.10
The MAX number of connections intervals supported by system. This parameter value is a function of atmNteConnectionsMaxNumber parameter. This parameter should affect the threshold values selected by user. Applicable to ace2002.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..96

atmNteAlarmType		1.3.6.1.4.1.164.12.3.1.2.11
This object specifies the type of the alarm.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), ais(2), rdi(3), continuityLoss(4), loopback(5)

atmNteLevel		1.3.6.1.4.1.164.12.3.1.2.12
This object specifies the ATM level.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	vp(2), vc(3)

atmNteConnectionsNumber		1.3.6.1.4.1.164.12.3.1.2.13
This object specifies a quantity of connections.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmNteTotalLb		1.3.6.1.4.1.164.12.3.1.2.14
This parameter counts the total number of end-points that were configured with Loopback (LB).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmNteTotalCc		1.3.6.1.4.1.164.12.3.1.2.15
This parameter counts the total number of end-points that were configured with Continuity Check (CC).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmNteTotalPm		1.3.6.1.4.1.164.12.3.1.2.16
This parameter counts the total number of end-points that were configured with PM.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmNteLoopback		1.3.6.1.4.1.164.12.3.2.2
OBJECT IDENTIFIER

atmLoopbackVpTable		1.3.6.1.4.1.164.12.3.2.2.1
This table contains parameters for an OAM VP loopback test.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmLoopbackVpEntry

atmLoopbackVpEntry		1.3.6.1.4.1.164.12.3.2.2.1.1
An entry in table atmLoopbackVpTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmLoopbackVpEntry

atmLoopbackVpIfIndex		1.3.6.1.4.1.164.12.3.2.2.1.1.1
The interface index of the ATM layer.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmLoopbackVpVpi		1.3.6.1.4.1.164.12.3.2.2.1.1.2
The VPI of the OAM VPL.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmLoopbackVpOperStatus		1.3.6.1.4.1.164.12.3.2.2.1.1.3
-noActive(1) means that the loopback test has not been activated for this VP. -inProgress(2) means that the test has been activated and there is currently no problem. -failed(3) means there was problem during the test or after having stopped it -endSuccessfully(4) means that the test was stopped and all was OK.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	noActive(1), inProgress(2), failed(3), endSuccessfully(4)

atmLoopbackVpCDV		1.3.6.1.4.1.164.12.3.2.2.1.1.4
Cell Delay Variation for this sampling.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmLoopbackVpAverageDelay		1.3.6.1.4.1.164.12.3.2.2.1.1.5
Average delay without including lost cells.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmLoopbackVpMaxDelay		1.3.6.1.4.1.164.12.3.2.2.1.1.6
Maximum delay without including lost cells.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmLoopbackVpMinDelay		1.3.6.1.4.1.164.12.3.2.2.1.1.7
Minimum delay.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmLoopbackVpErrSessions		1.3.6.1.4.1.164.12.3.2.2.1.1.8
Errored Sessions. Will be updated once in 5 seconds.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmLoopbackVcTable		1.3.6.1.4.1.164.12.3.2.2.2
This table contains parameters for an OAM VC loopback test.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmLoopbackVcEntry

atmLoopbackVcEntry		1.3.6.1.4.1.164.12.3.2.2.2.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmLoopbackVcEntry

atmLoopbackVcIfIndex		1.3.6.1.4.1.164.12.3.2.2.2.1.1
The interface index of the ATM layer.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmLoopbackVcVpi		1.3.6.1.4.1.164.12.3.2.2.2.1.2
The VPI of the OAM VCL.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmLoopbackVcVci		1.3.6.1.4.1.164.12.3.2.2.2.1.3
The VCI of the OAM VCL.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmLoopbackVcOperStatus		1.3.6.1.4.1.164.12.3.2.2.2.1.4
-noActive(1) means that the loopback test has not been activated for this VP. -inProgress(2) means that the test has been activated and there is currently no problem. -failed(3) means there was problem during the test or after having stopped it -endSuccessfully(4) means that the test was stopped and all was OK.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	noActive(1), inProgress(2), failed(3), endSuccessfully(4)

atmLoopbackVcCDV		1.3.6.1.4.1.164.12.3.2.2.2.1.5
Cell Delay Variation for this sampling.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmLoopbackVcAverageDelay		1.3.6.1.4.1.164.12.3.2.2.2.1.6
Average delay without including lost cells.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmLoopbackVcMaxDelay		1.3.6.1.4.1.164.12.3.2.2.2.1.7
The maximum delay without including lost cells.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmLoopbackVcMinDelay		1.3.6.1.4.1.164.12.3.2.2.2.1.8
The minimum delay.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmLoopbackVcErrSessions		1.3.6.1.4.1.164.12.3.2.2.2.1.9
Errored Sessions. Will be updated once in 5 seconds.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmLoopbackVpIvlTable		1.3.6.1.4.1.164.12.3.2.2.3
This table contains parameters for an OAM VP loopback test, according interval number.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmLoopbackVpIvlEntry

atmLoopbackVpIvlEntry		1.3.6.1.4.1.164.12.3.2.2.3.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmLoopbackVpIvlEntry

atmLoopbackVpIvlIfIndex		1.3.6.1.4.1.164.12.3.2.2.3.1.1
The interface index of the ATM layer.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmLoopbackVpIvlVpi		1.3.6.1.4.1.164.12.3.2.2.3.1.2
The VPI of the OAM VPL.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmLoopbackVpIvlIvl		1.3.6.1.4.1.164.12.3.2.2.3.1.3
The relevant interval number.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..96

atmLoopbackVpIvlOperStatus		1.3.6.1.4.1.164.12.3.2.2.3.1.4
-noActive(1) means that the loopback test has not been activated for this VP during this interval. -inProgress(2) has no meaning for an ended interval. -failed(3) means there was problem during the test or after having stopped it -endSuccessfully(4) means that the test was OK.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	noActive(1), inProgress(2), failed(3), endSuccessfully(4)

atmLoopbackVpIvlCDV		1.3.6.1.4.1.164.12.3.2.2.3.1.5
Cell Delay Variation for this interval.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmLoopbackVpIvlAverageDelay		1.3.6.1.4.1.164.12.3.2.2.3.1.6
Average delay without including lost cells for this interval.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmLoopbackVpIvlMaxDelay		1.3.6.1.4.1.164.12.3.2.2.3.1.7
The maximum delay without including lost cells for this interval.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmLoopbackVpIvlMinDelay		1.3.6.1.4.1.164.12.3.2.2.3.1.8
The minimum delay for this interval.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmLoopbackVpIvlErrSessions		1.3.6.1.4.1.164.12.3.2.2.3.1.9
Errored Sessions. Will be updated once in 5 seconds.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmLoopbackVcIvlTable		1.3.6.1.4.1.164.12.3.2.2.4
This table contains parameters for an OAM VC loopback test.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmLoopbackVcIvlEntry

atmLoopbackVcIvlEntry		1.3.6.1.4.1.164.12.3.2.2.4.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmLoopbackVcIvlEntry

atmLoopbackVcIvlIfIndex		1.3.6.1.4.1.164.12.3.2.2.4.1.1
The interface index of the ATM layer.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmLoopbackVcIvlVpi		1.3.6.1.4.1.164.12.3.2.2.4.1.2
The VPI of the OAM VCL.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmLoopbackVcIvlVci		1.3.6.1.4.1.164.12.3.2.2.4.1.3
The VCI of the OAM VCL.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmLoopbackVcIvlIvl		1.3.6.1.4.1.164.12.3.2.2.4.1.4
The relevant interval number.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..96

atmLoopbackVcIvlOperStatus		1.3.6.1.4.1.164.12.3.2.2.4.1.5
-noActive(1) means that the loopback test has not been activated for this VC during this interval. -inProgress(2) has no meaning per interval. -failed(3) means there was problem for this test during this interval. -endSuccessfully(4) means that the test was OK.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	noActive(1), inProgress(2), failed(3), endSuccessfully(4)

atmLoopbackVcIvlCDV		1.3.6.1.4.1.164.12.3.2.2.4.1.6
Cell Delay Variation for this interval.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmLoopbackVcIvlAverageDelay		1.3.6.1.4.1.164.12.3.2.2.4.1.7
Average delay without including lost cells.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmLoopbackVcIvlMaxDelay		1.3.6.1.4.1.164.12.3.2.2.4.1.8
The maximum delay without including lost cells.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmLoopbackVcIvlMinDelay		1.3.6.1.4.1.164.12.3.2.2.4.1.9
The minimum delay.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmLoopbackVcIvlErrSessions		1.3.6.1.4.1.164.12.3.2.2.4.1.10
Errored Sessions. Will be updated once in 5 seconds.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmNtePM		1.3.6.1.4.1.164.12.3.2.3
OBJECT IDENTIFIER

atmVpPmTable		1.3.6.1.4.1.164.12.3.2.3.1
This table contains parameters for VP performance monitoring.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmVpPmEntry

atmVpPmEntry		1.3.6.1.4.1.164.12.3.2.3.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmVpPmEntry

atmVpPmIfIndex		1.3.6.1.4.1.164.12.3.2.3.1.1.1
The interface index of the ATM layer.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmVpPmVpi		1.3.6.1.4.1.164.12.3.2.3.1.1.2
The VPI of the Performance Monitoring VPL.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmVpPmAdminStatus		1.3.6.1.4.1.164.12.3.2.3.1.1.3
up(2) - Activate PM. down(3) - Deactivate PM. listenToActivationCells(4) - . originateActivationCells(5) - .
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	up(2), down(3), listenToActivationCells(4), originateActivationCells(5)

atmVpPmDirection		1.3.6.1.4.1.164.12.3.2.3.1.1.4
The direction of PM.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	source(2), destination(3), bidirectional(4)

atmVpPmBlockSize		1.3.6.1.4.1.164.12.3.2.3.1.1.5
Valid block sizes (in cells): 128, 256, 512, 1024, 2048, 4096, 8192, 16384, 32768.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

atmVpPmRowStatus		1.3.6.1.4.1.164.12.3.2.3.1.1.6
Creation/Deletion of rows in the table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

atmVpPmSink		1.3.6.1.4.1.164.12.3.2.3.1.1.7
off (1) - Deactivate PM. fwd (2) - Activate Forward PM only. fwdAndBwdReport(3) - Activate Forward PM and Backward reporting.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	off(1), fwd(2), fwdAndBwdReport(3)

atmVpPmSource		1.3.6.1.4.1.164.12.3.2.3.1.1.8
off (1) - Deactivate PM. fwd (2) - Activate Forward PM only. fwdAndBwdReport(3) - Activate Forward PM and Backward reporting.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	off(1), fwd(2), fwdAndBwdReport(3)

atmVcPmTable		1.3.6.1.4.1.164.12.3.2.3.2
This table contains parameters for VC performance monitoring.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmVcPmEntry

atmVcPmEntry		1.3.6.1.4.1.164.12.3.2.3.2.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmVcPmEntry

atmVcPmIfIndex		1.3.6.1.4.1.164.12.3.2.3.2.1.1
The interface index of the ATM layer.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmVcPmVpi		1.3.6.1.4.1.164.12.3.2.3.2.1.2
The VPI of the Performance Monitoring VCL.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmVcPmVci		1.3.6.1.4.1.164.12.3.2.3.2.1.3
The VCI of the PM VCL.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmVcPmAdminStatus		1.3.6.1.4.1.164.12.3.2.3.2.1.4
up(2) - Activate PM. down(3) - Deactivate PM. listenToActivationCells(4) - . originateActivationCells(5) - .
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	up(2), down(3), listenToActivationCells(4), originateActivationCells(5)

atmVcPmDirection		1.3.6.1.4.1.164.12.3.2.3.2.1.5
The direction of PM.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	source(2), destination(3), bidirectional(4)

atmVcPmBlockSize		1.3.6.1.4.1.164.12.3.2.3.2.1.6
Valid block sizes (in cells): 128, 256, 512, 1024, 2048, 4096, 8192, 16384, 32768.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

atmVcPmRowStatus		1.3.6.1.4.1.164.12.3.2.3.2.1.7
Creation/Deletion of rows in the table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

atmVcPmSink		1.3.6.1.4.1.164.12.3.2.3.2.1.8
off (1) - Deactivate PM. fwd (2) - Activate Forward PM only. fwdAndBwdReport(3) - Activate Forward PM and Backward reporting.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	off(1), fwd(2), fwdAndBwdReport(3)

atmVcPmSource		1.3.6.1.4.1.164.12.3.2.3.2.1.9
off (1) - Deactivate PM. fwd (2) - Activate Forward PM only. fwdAndBwdReport(3) - Activate Forward PM and Backward reporting.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	off(1), fwd(2), fwdAndBwdReport(3)

atmNteMdl		1.3.6.1.4.1.164.12.3.3
OBJECT IDENTIFIER

atmNteMdlConfig		1.3.6.1.4.1.164.12.3.3.1
OBJECT IDENTIFIER

atmNteMdlConfigTable		1.3.6.1.4.1.164.12.3.3.1.1
Module configuration table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmNteMdlConfigEntry

atmNteMdlConfigEntry		1.3.6.1.4.1.164.12.3.3.1.1.1
There is an entry in this table just for those modules that have parameters that are relevant to module level only.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmNteMdlConfigEntry

atmNteMdlSlotIndex		1.3.6.1.4.1.164.12.3.3.1.1.1.1
The slot number.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..4

atmNteMdlPrtCpuSharing		1.3.6.1.4.1.164.12.3.3.1.1.1.2
This object lets the user decide what will be the CPU sharing between the ports of the module. This object is applicable for modules in which the same CPU handles the traffic of all ports. equal - All ports will have the same CPU resource. port1 - Port 1 will have higher priority than the other ports.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	equal(2), port1(3)

atmNteMdlInputPriorityMechanism		1.3.6.1.4.1.164.12.3.3.1.1.1.3
This object allows the user to Enable/Disable the Input priority mechanism. This object is applicable for modules with more than one port, in which the total ports input may be greater than the port output. disabled - all LAN VCCs will be transmitted through the same queue (queue 1). Upon congestion frames will be dropped randomly. enabled - the user should configure each port/connection priority. Upon congestion frames will be dropped according to priority.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(2), enabled(3)

atmGenSystem		1.3.6.1.4.1.164.12.2.2
OBJECT IDENTIFIER

atmGenSysGen		1.3.6.1.4.1.164.12.2.2.1
OBJECT IDENTIFIER

atmGenSysSelfTestTable		1.3.6.1.4.1.164.12.2.2.1.1
A table containing the results of the initial testing of the device.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmGenSysSelfTestEntry

atmGenSysSelfTestEntry		1.3.6.1.4.1.164.12.2.2.1.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmGenSysSelfTestEntry

atmGenSysSelfTestIndex		1.3.6.1.4.1.164.12.2.2.1.1.1.1
A running index for the table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmGenSysSelfTestResult		1.3.6.1.4.1.164.12.2.2.1.1.1.2
The results of the initial testing of the device.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

atmGenSysSelfTestModule		1.3.6.1.4.1.164.12.2.2.1.1.1.3
The name of module on which the test was performed.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

atmGenSysLogClearAll		1.3.6.1.4.1.164.12.2.2.1.2
Setting the variable to clear(3) removes all entries in the Log Buffer of the agent. The agent will immediately reset the variable to off(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), clear(3)

atmGenSysLogTable		1.3.6.1.4.1.164.12.2.2.1.3
A copy of the log buffer.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmGenSysLogEntry

atmGenSysLogEntry		1.3.6.1.4.1.164.12.2.2.1.3.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmGenSysLogEntry

atmGenSysLogIndex		1.3.6.1.4.1.164.12.2.2.1.3.1.1
The index of the log buffer.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..2048

atmGenSysLogMessage		1.3.6.1.4.1.164.12.2.2.1.3.1.2
The log buffer entry message text.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(80)

atmGenSysSetDefaultConfg		1.3.6.1.4.1.164.12.2.2.1.4
When set to on(3), the agent will set all the configuration parameters to their default values. The variable is then reset to off(2) by the agent. The agent must be reset for the default configuration to apply.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

atmGenSysCxRefTable		1.3.6.1.4.1.164.12.2.2.1.5
A Cross Reference table. The table maintains an index of an object which is also the table index, and a counter that indicates how many times this object was referenced. When using this table for more than one referenced table, which uses the same range of indexes, then the index should be shifted by a unique offset per table. In ACE2002 this table is used for TD and for FR Desc. Thus, the index for FR Descriptor is: FR Descriptor index + offset. The offset is described in the ACE2002 NMS SRS.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmGenSysCxRefEntry

atmGenSysCxRefEntry		1.3.6.1.4.1.164.12.2.2.1.5.1
The entries will be added by the agent upon an entry addition in the referenced tables (TD table, FR Descriptor etc.)
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmGenSysCxRefEntry

atmGenSysCxRefIndex		1.3.6.1.4.1.164.12.2.2.1.5.1.1
The index specifies an entry in the table of the object.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

atmGenSysCxRefCounter		1.3.6.1.4.1.164.12.2.2.1.5.1.2
The counter counts the number of references that have been made to the object .
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

atmAceStatusChange		1.3.6.1.4.1.164.12.3.0.1
The trap is sent every time there is a change in the state of one of the LEDs.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmTrap		1.3.6.1.4.1.164.12.3.0.2
The trap is sent whenever there is a transition from a no alarm state to a state with at least one active alarm. An active alarm state exists if: 1) The atmInterfaceActiveAlarms vector is different than 0. 2) The atmNteAlarmVpTable contains entries. 3) The atmNteAlarmVcTable contains entries. The trap is also sent when a transition into the no alarm state occurs. The second variable will be atmInterfaceActiveAlarms to indicate the kind of the alarm. The trap is not sent more than once in a 10 second interval.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceModuleChangeTrap		1.3.6.1.4.1.164.12.3.0.3
The trap is sent every time a module is changed (Hot swapping). The second variable will be atmNteCardType to indicate the type of card that was inserted. The value empty(255) indicates that a card was taken out.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceRedundancyTrap		1.3.6.1.4.1.164.12.3.0.4
The trap is sent upon change in link as a result of redundancy. The ifIndex parameter indicates the current active link.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceModuleMismatchTrap		1.3.6.1.4.1.164.12.3.0.5
The trap is sent upon starting or stopping of a module mismatch state. A possible mismatch is when the inserted module is other than the programmed one.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceSystemTrap		1.3.6.1.4.1.164.6.1.12.0.6
This trap alerts of major problems in the device.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmForwardingTrap		1.3.6.1.4.1.164.6.1.12.0.7
This trap is sent upon starting or stopping Alarm Forwarding Mechanism.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceDateAndTimeRequest		1.3.6.1.4.1.164.6.1.12.0.8
This trap is sent upon restart. Upon recieving this trap the NMS will set the device's date and time. This trap's purpose is to fix a problem in ACE2002, ACE-2002E, ACE-202. The problem is that the Date and Time is stored in the NVRAM, and when the NVRAM's battery is empty, the device loses this information.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmLOS		1.3.6.1.4.1.164.6.1.12.0.16
This trap indicates Loss Of Signal.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmLOF		1.3.6.1.4.1.164.6.1.12.0.17
This trap indicates Loss Of Frame.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmLCD		1.3.6.1.4.1.164.6.1.12.0.18
This trap indicates Loss of Cell Delineation.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmSLM		1.3.6.1.4.1.164.6.1.12.0.19
This trap indicates Signal Line Mismatch.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmLOP		1.3.6.1.4.1.164.6.1.12.0.20
This trap indicates Loss of Pointer.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmLineAIS		1.3.6.1.4.1.164.6.1.12.0.21
This trap indicates Line AIS.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmPathAIS		1.3.6.1.4.1.164.6.1.12.0.22
This trap indicates Path AIS.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmLineRDI		1.3.6.1.4.1.164.6.1.12.0.23
This trap indicates Line RDI.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmPathRDI		1.3.6.1.4.1.164.6.1.12.0.24
This trap indicates Path RDIand Path RAI(Yellow) for DS1 interfaces.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmSectionBIP		1.3.6.1.4.1.164.6.1.12.0.25
This trap indicates Section Bit Interleave Parity.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmLineBIP		1.3.6.1.4.1.164.6.1.12.0.26
This trap indicates Line Bit Interleave Parity.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmPathBIP		1.3.6.1.4.1.164.6.1.12.0.27
This trap indicates Path Bit Interleave Parity.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmLineFEBE		1.3.6.1.4.1.164.6.1.12.0.28
This trap indicates Line Far End Block Error.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmPathFEBE		1.3.6.1.4.1.164.6.1.12.0.29
This trap indicates Path Far End Block Error.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmPlcpLOF		1.3.6.1.4.1.164.6.1.12.0.30
This trap indicates T3 PLCP Loss Of Frame.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmPlcpYELLOW		1.3.6.1.4.1.164.6.1.12.0.31
This trap indicates T3 Plcp Yellow.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmPlcpBIP		1.3.6.1.4.1.164.6.1.12.0.32
This trap indicates T3 Plcp Bit Interleave Parity.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmPlcpFEBE		1.3.6.1.4.1.164.6.1.12.0.33
This trap indicates T3 Plcp Far End Block Error.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmPlcpP1P2		1.3.6.1.4.1.164.6.1.12.0.34
This trap indicates T3 Plcp Parity errors in P1/P2 bytes.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmUAS		1.3.6.1.4.1.164.6.1.12.0.35
This trap is sent upon UAS start or end per port.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmCluster		1.3.6.1.4.1.164.6.1.12.0.36
This trap is sent upon atmNteAlarmType start or end, for a cluster of VPs/VCs (according to atmNteLevel) with the same alarm on the same physical port. This trap replaces sending the same alarm for a big quantity (the quantity described in the product specification document) of VPs/VCs in order to prevent flooding the NMS and the network with traps.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceHwFailure		1.3.6.1.4.1.164.6.1.12.0.37
This trap is sent upon HW failure per port.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceUnavailableBwTrap		1.3.6.1.4.1.164.6.1.12.0.38
This trap is sent when Bandwidth allocation is > max possible value for the installed card. For ACE2002 this trap will be sent for the following cases: Card insertion - if the total Input and/or Output Bandwidth is over allocated, then the specific card rate will be set to 0 and this trap will be sent with the Input/Output rates values. Upgrade from former version - when an over allocated Bandwidth is detected, this trap will be sent with atmConfIfInputRate=atmConfIfOutputRate=0xFFFFFFFF.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmVpContinuityLoss		1.3.6.1.4.1.164.6.1.12.0.40
This trap indicates Loss of Continuity Check on a VP Connection.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmVpAISReception		1.3.6.1.4.1.164.6.1.12.0.41
This trap indicates AIS Reception on a VP Connection.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmVpRDIReception		1.3.6.1.4.1.164.6.1.12.0.42
This trap indicates RDI Reception on a VP Connection.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmVpErroredCells		1.3.6.1.4.1.164.6.1.12.0.43
This trap indicates Errored Cells on a VP Connection reported by PM.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmVpLostCells		1.3.6.1.4.1.164.6.1.12.0.44
This trap indicates Lost Cells on a VP Connection reported by PM.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmVpMisinsertedCells		1.3.6.1.4.1.164.6.1.12.0.45
This trap indicates Misinserted Cells on a VP Connection reported by PM.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmVpUAS		1.3.6.1.4.1.164.6.1.12.0.46
This trap is sent upon UAS start or end per VP.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmVpLoopback		1.3.6.1.4.1.164.6.1.12.0.47
This trap is sent upon OAM LoopBack fail status per VP.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmVpGCRAViolation		1.3.6.1.4.1.164.6.1.12.0.48
This trap indicates GCRA violation on a VP Connection reported by UPC device.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmVcContinuityLoss		1.3.6.1.4.1.164.6.1.12.0.56
This trap indicates Loss of Continuity Check on a VC Connection.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmVcAISReception		1.3.6.1.4.1.164.6.1.12.0.57
This trap indicates AIS Reception on a VC.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmVcRDIReception		1.3.6.1.4.1.164.6.1.12.0.58
This trap indicates RDI Reception on a VC Connection.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmVcErroredCells		1.3.6.1.4.1.164.6.1.12.0.59
This trap indicates Errored Cells on a VC Connection reported by PM.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmVcLostCells		1.3.6.1.4.1.164.6.1.12.0.60
This trap indicates Lost Cells on a VC Connection reported by PM.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmVcMisinsertedCells		1.3.6.1.4.1.164.6.1.12.0.61
This trap indicates Misinserted Cells on a VC Connection reported by PM.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmVcUnexpectedCell		1.3.6.1.4.1.164.6.1.12.0.62
This trap indicates an unexpected cell from user or network port.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmVcUAS		1.3.6.1.4.1.164.6.1.12.0.63
This trap is sent upon UAS start or end per VC.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmVcLoopback		1.3.6.1.4.1.164.6.1.12.0.64
This trap is sent upon OAM LoopBack fail status per VC.
Status: current	Access: read-only
NOTIFICATION-TYPE

atmAceAlarmVcGCRAViolation		1.3.6.1.4.1.164.6.1.12.0.65
This trap indicates GCRA violation on a VC Connection reported by UPC device.
Status: current	Access: read-only
NOTIFICATION-TYPE

ip2If		1.3.6.1.4.1.164.3.1.6.7
OBJECT IDENTIFIER

ip2IfTable		1.3.6.1.4.1.164.3.1.6.7.1
Channels Configuration Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Ip2IfEntry

ip2IfEntry		1.3.6.1.4.1.164.3.1.6.7.1.1
Application layer configuration per link
Status: current	Access: not-accessible
OBJECT-TYPE
	Ip2IfEntry

ip2IfChannelIndex		1.3.6.1.4.1.164.3.1.6.7.1.1.1
The channel index, which is actualy the bundle ID.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ip2IfRowStatus		1.3.6.1.4.1.164.3.1.6.7.1.1.2
This parameter allows NMS to create/delete entries of this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

ip2IfOperStatus		1.3.6.1.4.1.164.3.1.6.7.1.1.3
The actual link status. remoteFail - No Rx. localFail - No Tx. unavailable - No echo replay or replay with invalid code or when connection is in Test state. valiodationFail - Connection is in not valid state. standby - offline (can be in pre-sync mode). tdmFail - oper status is down cause of failure in the tdm. hwMismatch - the bundle exists on a card that is not installed or has a different type than the programmed card.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	down(2), up(3), disabled(4), remoteFail(5), localFail(6), unavailable(7), validationFail(8), standby(9), tdmFail(10), hwMismatch(11)

ip2IfAdminStatus		1.3.6.1.4.1.164.3.1.6.7.1.1.4
The desired state of the link.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	down(2), up(3)

ip2IfDestAddr		1.3.6.1.4.1.164.3.1.6.7.1.1.5
The destination IP address.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

ip2IfNextHop		1.3.6.1.4.1.164.3.1.6.7.1.1.6
The next hop to which the frame should be sent. Default value - 0.0.0.0. Upon setting the default value the frame is sent to the default Gateway.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

ip2IfDestPort		1.3.6.1.4.1.164.3.1.6.7.1.1.7
The destination Bundle at the far-end device.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

ip2IfMacAddr		1.3.6.1.4.1.164.3.1.6.7.1.1.8
The Destination MAC address of the next hop or destination station.
Status: current	Access: read-create
OBJECT-TYPE
	MacAddress

ip2IfJitterBuffer		1.3.6.1.4.1.164.3.1.6.7.1.1.9
The maximum cell arrival jitter in 10 usec that the reassembly process will tolerate in the cell stream, without producing errors on the CBR service interface. For KM2100: KML.11 - The range that will be used is 3...300 msec in steps of 1 msec. For Vmux: The range that will be used is 20...100 msec in steps of 10 msec.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

ip2IfTos		1.3.6.1.4.1.164.3.1.6.7.1.1.10
The TOS (Type of Service) value: 0..255. In Vmux-2100/110 devices versions 3.1 and up, in Vmux-210 and in Vmux-4x0: LSB 8 bits - 00 00 00 XX will be used for Signaling packets TOS. Next 8 bits - 00 00 XX 00 will be used for Media packets TOS. Next 16 bits - will be 0. XX = Hex values: 0..FF For mixed packets, TOS of Media Packets will be used. Signaling packets are for example: Keep alive packets and ABCD signaling bits. Media packets are for example: voice, fax, HDLC, payload packets.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

ip2IfTDMBytesInFrame		1.3.6.1.4.1.164.3.1.6.7.1.1.11
The number of TDM bytes to be placed in a single IP frame payload. For ip2IfTDMoIpMode = cesOverPsn this parameter indicates the number of IP frames, calculated as: 1440/.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

ip2IfVlanSupport		1.3.6.1.4.1.164.3.1.6.7.1.1.12
VLAN support (Tagging). no - No support to VLAN. yes - 4 VLAN bytes will be added to the frame.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	no(2), yes(3)

ip2IfVlanIdentifier		1.3.6.1.4.1.164.3.1.6.7.1.1.13
VLAN ID.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

ip2IfVlanFramePriority		1.3.6.1.4.1.164.3.1.6.7.1.1.14
VLAN Frame priority.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

ip2IfExitPort		1.3.6.1.4.1.164.3.1.6.7.1.1.15
This object determines to which external port the traffic will be sent. auto - the device will decide automatically the exit port. If there is an option for Tx via more than one ETH card then use ext1 (1) and ext2(2) for ETH card #1 (ex. LAN1 or Ggabit-ETH1) and use card2Ext1(5) and card2Ext2(6) for card #2 (ex. LAN1 or Ggabit-ETH1). In Vmux-110/210 ext5 is used for ETH-NET, ext 6 is used for E1/T1 link and ext7 is used for Serial Link. In Vmux-2100 Main Board: ext 5 is used for ETH-NET, ext 6 is used for E1/T1 link A, prtE1T1B is used for E1/T1 link B and prtEthUser is used for ETH-User. prt17(10) - prt20(13) values were added in order to support Gmux2000 VMX Card.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notApplicable(1), ext1(2), ext2(3), auto(4), card2Ext1(5), card2Ext2(6), ext5(7), ext7(8), ext6(9), prt17(10), prt18(11), prt19(12), prt20(13), prtE1T1B(14), prtEthUser(15), card3Ext1(16), card3Ext2(17), card3Ext3(18), card3Ext4(19), card4Ext1(20), card4Ext2(21), card4Ext3(22), card4Ext4(23), card1Ext3(24), card1Ext4(25), card1Ext5(26), card1Ext6(27), card1Ext7(28), card1Ext8(29), card2Ext3(30), card2Ext4(31), card2Ext5(32), card2Ext6(33), card2Ext7(34), card2Ext8(35)

ip2IfVoiceOos		1.3.6.1.4.1.164.3.1.6.7.1.1.16
Voice Out-Of-Service code. Valid range: (0 - FF HEX). For agents that do not support this feature, the value will always be 0.
Status: current	Access: read-create
OBJECT-TYPE
	OCTET STRING

ip2IfDataOos		1.3.6.1.4.1.164.3.1.6.7.1.1.17
Data Out-Of-Service code. Valid range: (0 - FF HEX). For agents that do not support this feature, the value will always be 0.
Status: current	Access: read-create
OBJECT-TYPE
	OCTET STRING

ip2IfBundleUsage		1.3.6.1.4.1.164.3.1.6.7.1.1.18
The Bundle Resource usage in Kbps.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ip2IfOAM		1.3.6.1.4.1.164.3.1.6.7.1.1.19
This parameter determine the OAM configuration. The LSB (Bit 0 the most right one) is used for OAM connectivity. Values: 0 = disable, 1= enable.
Status: current	Access: read-create
OBJECT-TYPE
	OCTET STRING

ip2IfTDMoIpMode		1.3.6.1.4.1.164.3.1.6.7.1.1.20
The TDMoIP Mode configuration. Static- means TS can Tx any time. dynamicLES - means TS can Tx only when line is enabled according to LES protocol. dynamicCAS - means TS can Tx only when line is enabled according to CAS protocol. cesOverIp - use for information that this bundle is used for CES Over IP. voiceOverMpls - Voice over Multi Protocol Label Switching. hdlc - High Level Data Link. voIpComprHeader - indicates proprietary compressed IP header packets. voMplsComprHeader - indicates proprietary compressed MPLS header packets.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notApplicable(1), static(2), dynamicLES(3), dynamicCAS(4), cesOverIp(5), voiceOverMpls(6), hdlc(7), voIpComprHeader(8), voMplsComprHeader(9), satop(10), cesOverPsn(11), hdlcOverPsn(12)

ip2IfTimeElapsed		1.3.6.1.4.1.164.3.1.6.7.1.1.21
The number of seconds that have elapsed since the beginning of the current error-measurement period. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..899

ip2IfValidIntervals		1.3.6.1.4.1.164.3.1.6.7.1.1.22
The number of previous intervals for which data was collected. The value will be 96 unless the interface was brought online within the last 24 hours, in which case the value will be the number of complete 15 minute intervals since the interface has been online.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..96

ip2IfFarEndType		1.3.6.1.4.1.164.3.1.6.7.1.1.23
This object defines the type of the Far-End device. This data is important for signaling and DS0 format. For Vmux: e1 (2) value is used for a PBX in the Far End. fxs (5) is used for Phone. Other values are not used.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notApplicable(1), e1(2), t1Esf(3), t1D4(4), fxs(5), serialLink(6), t1Unframed(7)

ip2IfRdnState		1.3.6.1.4.1.164.3.1.6.7.1.1.24
This object defines the role this bundle plays in the redundancy scheme: none(2) - means this bundle is not part of redundancy pair. primary/ secondary - means this bundle is not part of redundancy pair, and that is the primary bundle or the secondary bunle.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), none(2), primary(3), secondary(4)

ip2IfSourceAddr		1.3.6.1.4.1.164.3.1.6.7.1.1.25
Source IP Address of the bundle.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

ip2IfBandWidth		1.3.6.1.4.1.164.3.1.6.7.1.1.26
Defines the Bandwidth of the bundle. For TDM bundles - it is the Number of Time Slots in The Bundle. - For T1 the value will be: 1..24 - For E1 the value will be: 1..31 - For T3 the value will be: 1..84 - For E3 the value will be: 1..63 This parameter is required for devices like Emux where the bandwidth of the bundles is unknown. The bundles that are received should be transmitted without any change in the bandwidth. It is the user's responsibility to enter the correct bandwidth. For Ethernet bundles - it is the bandwidth, measured in Kbps.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

ip2IfMeasuredSilence		1.3.6.1.4.1.164.3.1.6.7.1.1.27
This object shows the percentage of Silence that was measured by the device for the current bundle in the transmitted payload. Relevant values: 0..100, 255. Default value is 50. 0 means that there is no silence on the line. 100 means that there is only silence. In this case, there might be no traffic. 255 - value for not applicable or unknown.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ip2IfPayloadType		1.3.6.1.4.1.164.3.1.6.7.1.1.28
This object defines the TDMoIP payload type.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notApplicable(1), data(2), voice(3), voiceAndCas(4)

ip2IfProtocolVersion		1.3.6.1.4.1.164.3.1.6.7.1.1.29
This object defines the TDMoIP protocol Version.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notApplicable(1), v1(2), v2(3)

ip2IfTdmBackUpNextHop		1.3.6.1.4.1.164.3.1.6.7.1.1.30
Defines the TDM bundle default router in case there was a switch from the Primary Link (for example an ETH port) to a TDM backup Link like E1, T1 or Serial Link. This parameter is relevant only when a Backup Link is configured. When a Backup Link is not configured the value will be: 0.0.0.0
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

ip2IfOosTxEnable		1.3.6.1.4.1.164.3.1.6.7.1.1.31
This object defines whether OOS will be Transmitted. Note that for IPmux1000 the Lbit is always sent, but the OOS will be sent according to user selection in this parameter.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), enable(3)

ip2IfConnCheckPktFrequency		1.3.6.1.4.1.164.3.1.6.7.1.1.32
Time in sec. between 2 Bundle Connectivity Check packets. Valid values: 0..60. 0 = Not Applicable.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

ip2IfConnPktTimeOutCycles		1.3.6.1.4.1.164.3.1.6.7.1.1.33
No. of cycles the agent will send Bundle Connectivity packets without receiving a response from the remote device before declaring that the bundle connection to the remote side is down - Time Out. Valid values: 0..5. 0 = Not Applicable.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

ip2IfMfRelay		1.3.6.1.4.1.164.3.1.6.7.1.1.34
Multi Frequency Signaling Detection.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), enable(3)

ip2IfTxGain		1.3.6.1.4.1.164.3.1.6.7.1.1.35
Transmit gain in dBm.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

ip2IfSuperTandem		1.3.6.1.4.1.164.3.1.6.7.1.1.36
The Super Tandem feature provides end to end compression over multiple hops, solving the double compression problem detected in Voice compressing systems. The Super Tandem allows transmission of compressed voice between a few Vmux 2100 hubs, and eliminates the need to decompress an recompress it over each voice card and PBX, thus improving voice quality and reducing delay.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), enable(3)

ip2IfSrcPort		1.3.6.1.4.1.164.3.1.6.7.1.1.37
The source Bundle at the local device, this parameter used for cases where there is no match between ip2IfChannelIndex and the Source Bundle ID.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

ip2IfModemCalls		1.3.6.1.4.1.164.3.1.6.7.1.1.38
This MIB object shows whether Modem Calls are enabled via the bundle. relay option (3) means that the bundle will send to the network only modulated data.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disable(2), enable(3), relay(4)

ip2IfMinPulseWidth		1.3.6.1.4.1.164.3.1.6.7.1.1.39
Indicates the minimum width in milliseconds of the MF (Multi Frequency) tone transmitted by the switch. Valid values: 45-300 msec. notApplicable=0.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

ip2IfMinPowerLevel		1.3.6.1.4.1.164.3.1.6.7.1.1.40
Indicates the minimum power level in dBm of the MF (Multi Frequency) tone transmitted by the switch. Valid values: -1...-35 dBm.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

ip2IfEchoCanceler		1.3.6.1.4.1.164.3.1.6.7.1.1.41
Echo canceler activation.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	off(2), on(3)

ip2IfCodingLaw		1.3.6.1.4.1.164.3.1.6.7.1.1.42
This attribute indicates the Method/Law for decoding/encoding the voice information. aLaw(1) is the standard Law for E1 links. uLaw(2) is the standard Law for T1 links.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	aLAW(1), uLAW(2)

ip2IfCustomToneDetect		1.3.6.1.4.1.164.3.1.6.7.1.1.43
Custom Tone Detection (COT) is a Control operation of a 2Khz tone detector. This tone is sent between PBX devices in order to check that the line status is OK. When the COT is enabled the device will not compress/decompress the tone. In this case, if the tone is initiated by the local PBX, the Device runs a 2Khz detector tone and once detected by the Remote Device, if the COT is enabled in the Remote Device, the Remote Device will generate a 2khz tone to the remote PBX.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disable(2), enable(3)

ip2IfCallerIdDelay		1.3.6.1.4.1.164.3.1.6.7.1.1.44
Time in msec between CLID (Caller ID) signal detection on the line and CLID signal transmission. The CLID must be sent between ringing signals and the value of the delay is used for synchronizing the CLID transmission with the ringing signals transmission. Valid values: 0 - 3000 msec.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

ip2IfConnectivityMode		1.3.6.1.4.1.164.3.1.6.7.1.1.45
This MIB object shows whether to send Pings or OAM frames over the bundle.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	ping(2), oam(3)

ip2IfClockSourceEnable		1.3.6.1.4.1.164.3.1.6.7.1.1.46
This MIB object defines whether this bundle can be a clock source.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), enable(3)

ip2IfNetworkType		1.3.6.1.4.1.164.3.1.6.7.1.1.47
This MIB object defines the network over which the Bundle PSN (Packet Switching Network)is transported. In Gmux2000: ipComprHeader indicates proprietary compressed IP header packets. mplsComprHeader indicates proprietary compressed MPLS header packets.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notApplicable(1), ip(2), mplsEth(3), mac(4), ipComprHeader(5), mplsComprHeader(6), udp(7)

ip2IfMplsRxLabelEnable		1.3.6.1.4.1.164.3.1.6.7.1.1.48
This MIB object defines whether there is user defined inner (Rx.) label for this Bundle.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), enable(3)

ip2IfMplsRxLabel		1.3.6.1.4.1.164.3.1.6.7.1.1.49
This MIB object defines the MPLS Rx. Label for this Bundle.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

ip2IfMplsTxLabelEnable		1.3.6.1.4.1.164.3.1.6.7.1.1.50
This MIB object defines whether there is user defined outer (Tx.) label for this Bundle.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), enable(3)

ip2IfMplsTxLabel		1.3.6.1.4.1.164.3.1.6.7.1.1.51
This MIB object defines the MPLS Tx. Label for this Bundle.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

ip2IfMplsTxExpBits		1.3.6.1.4.1.164.3.1.6.7.1.1.52
The MPLS Network priority (EXP bits) used for this bundle.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..7

ip2IfMfcSpoofing		1.3.6.1.4.1.164.3.1.6.7.1.1.53
This MIB object defines whether the MFC (Multi Frequency Compelled) protocol spoofing will exist in the bundle. When the MFC Spoofing is used, the Local and Remote PBXs will send MFC Signaling to each other. The Vmuxes between the PBXs will send proprietary signaling to each other. They will however create and send MFC tones to their local PBX. The PBXs will not know that the actual signaling was not sent from a PBX but from a Vmux.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), enable(3)

ip2IfToneAckInterval		1.3.6.1.4.1.164.3.1.6.7.1.1.54
Time Interval in milli seconds from the time a Vmux sends tone/s to a local PBX until it receives an acknowledgement from this PBX. Valid values: 60...400 in steps of 20.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

ip2IfNextHopType		1.3.6.1.4.1.164.3.1.6.7.1.1.55
This MIB object defines the Bundle next Hop Address Type.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notApplicable(1), ipAddress(2), macAddress(3)

ip2IfNoiseLevelForVAD		1.3.6.1.4.1.164.3.1.6.7.1.1.56
This object defines the Level of Noise on the line, the Voice Activation Detector (VAD) will have to handle.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	low(2), high(3), off(4)

ip2IfClockPreferences		1.3.6.1.4.1.164.3.1.6.7.1.1.57
The Clock preferences: accurateness (2) = Accurate clock is more important than Constant Delay. constantDelay (3)= Constant Delay is more important than Accurate clock .
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	accurateness(2), constantDelay(3)

ip2IfConnectionMode		1.3.6.1.4.1.164.3.1.6.7.1.1.58
The Connection Mode: tdmOIpCe (2) = TDMOiP (CE) = Circuit Emulation. tdmOIpCv (3)= TDMOiP (CV) = Compressed Voice.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	tdmOIpCe(2), tdmOIpCv(3)

ip2IfRingBack		1.3.6.1.4.1.164.3.1.6.7.1.1.59
Enables or disable Ring Back.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disable(2), enable(3)

ip2IfReversePolarity		1.3.6.1.4.1.164.3.1.6.7.1.1.60
Enables or disable Reverse polarity synthesis.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disable(2), enable(3)

ip2IfPulseMeter		1.3.6.1.4.1.164.3.1.6.7.1.1.61
Enables or disable Pulse metering synthesis.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disable(2), enable(3)

ip2IfPulseMeterFreq		1.3.6.1.4.1.164.3.1.6.7.1.1.62
Frequency of synthesized pulse metering for this bundle.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	rate12Khz(2), rate16Khz(3)

ip2IfPulseMeterPeriod		1.3.6.1.4.1.164.3.1.6.7.1.1.63
Duration of synthesized pulse metering. current values are: 100-250.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

ip2IfOnHookDetect		1.3.6.1.4.1.164.3.1.6.7.1.1.64
Enables or disable immediate reaction to On-Hook bits from network in Ringing.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disable(2), enable(3)

ip2IfComfortNoiseGen		1.3.6.1.4.1.164.3.1.6.7.1.1.65
Enable or disable Comfort Noise Generation (CNG). When this parameter is enabled and no voice payload exists on the line for some time period during the call (moments of silence), the device will generate a soft background noise which assures the user that the connection is still alive (CNG). When this parameter is disabled and no voice payload exists on the line, absolute silence will be heard (Comfort Noise will not be generated).
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disable(2), enable(3)

ip2IfExitChannel		1.3.6.1.4.1.164.3.1.6.7.1.1.66
The channelized bundle that the voice bundle exits through. In Gmux2000 it is the ifIndex of the Channelized Bundle (sub-channel) that the Voice Bundle exits through. The ifIndex contains the Slot+Prt+Channelized Bundle No.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

ip2IfMaxVBDModemCalls		1.3.6.1.4.1.164.3.1.6.7.1.1.67
Maximum VBD modem calls for this bundle.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

ip2IfMaxRelayModemCalls		1.3.6.1.4.1.164.3.1.6.7.1.1.68
Maximum Relay modem calls for this bundle.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

ip2IfCustomToneFrequency		1.3.6.1.4.1.164.3.1.6.7.1.1.69
This is the frequency of the Custom Tone that is sent between PBXs in order to check that the line status is OK. When the Custom Tone Detection is enabled the device will not compress/decompress this tone. The custom tone that is received from the local PBX will be sent to the remote PBX with the same frequency it was received. When the Custom Tone Frequency is f1780Plus2000Hz (4), the device will not compress/decompress any tone with frequencies of 1780Hz or 2000 Hz.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notApplicable(1), f1780Hz(2), f2000Hz(3), f1780Plus2000Hz(4)

ip2IfVadMethod		1.3.6.1.4.1.164.3.1.6.7.1.1.70
Voice Activity Detection (VAD) method. proprietary (2) - non standard VAD based only on power measurement. It is very sensitive to background noise. internalITUT (3) - standard ITU-T VAD. It is a robust method.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	proprietary(2), internalITUT(3)

ip2IfRxGain		1.3.6.1.4.1.164.3.1.6.7.1.1.71
Receive gain in dBm.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

ip2IfCallerIDType		1.3.6.1.4.1.164.3.1.6.7.1.1.72
Caller ID Type used by the DSP for this bundle. Bellcore type is used by the American method. V.23 type is used by the European method.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	bellcoreType1(2), v23(3)

ip2IfPeerAddrType		1.3.6.1.4.1.164.3.1.6.7.1.1.73
This MIB object defines the peer Address Type.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notApplicable(1), ipAddress(2), macAddress(3)

ip2IfVbdRate		1.3.6.1.4.1.164.3.1.6.7.1.1.74
Voice Band Data (VBD) rate for this bundle.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	r64KbpsIn5msecIntervalsG711(2), r64KbpsIn10msecIntervalsG711(3), r32KbpsG726(4), r24KbpsG726(5)

ip2IfDtmfDetection		1.3.6.1.4.1.164.3.1.6.7.1.1.75
Enable/Disable DTMF (Dual Tone Multi Frequency) detectors for this bundle.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), enable(3)

ip2IfNlpCutoffLevel		1.3.6.1.4.1.164.3.1.6.7.1.1.76
Non Linear Processor (NLP) Cutoff Level for this bundle. This parameter is used by the echo canceller. It is the maximum absolute linear PCM amplitude of the near-end signal that will cause the NLP module to be active and to mute low level residual echo & noisy surroundings.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

ip2IfDtdErlRatioCutoffQ3		1.3.6.1.4.1.164.3.1.6.7.1.1.77
The DTD ERL cutoff level is used in order to determine whether the near-end is talking or not. This parameter is used by the echo canceller when echo exists and there is voice with low volume on the line. DTD means Double Talk Detection. ERL means Echo Return Loss. It is the power difference [dB] between the far-end signal to the echo returned. The cutoff level is calculated for the value entering Q.3. This value will be divided by 2^3=8 in order to get the linear ratio.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

ip2IfCASRedundancy		1.3.6.1.4.1.164.3.1.6.7.1.1.78
Enable/Disable CAS signaling redundancy. This parameter is useful when there are problems with the network and applicable only for CAS signaling: E1-MF (G.732S) or E1-CRC-MF (G.732SCRC ). enable (3) - means that each packet containing CAS signaling will be triplicated into 3 packets. disable (2)- No redundancy will exist. Only 1 packet containing CAS will be transmitted.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), enable(3)

ip2IfBundleSensitivity		1.3.6.1.4.1.164.3.1.6.7.1.1.79
Denotes if the bundle is sensitive to delay in the network, or is sensitive to data errors in the network. Voice bundles are sensitive to delay; Non-voice bundles are sensitive to data errors.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	delaySensitive(2), dataSensitive(3)

ip2IfOAMBundleIdent		1.3.6.1.4.1.164.3.1.6.7.1.1.80
Denotes if an OAM bundle is identified according to the Bundle Number (0x3fff), or according to the value of the first nibble in the VCCV control word sent in the frame. controlWord - applicable only when ip2IfProtocolVersion = v2(2). When ip2IfProtocolVersion = v1(1), only bundleNumber is applicable.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	bundleNumber(2), vccvCtrlWord(3)

ip2IfMaxTxQueue		1.3.6.1.4.1.164.3.1.6.7.1.1.81
Max Tx Queue buffer size, measured in msec (milliseconds). Low buffer size may cause the buffer to overflow and discard packets in case of burst of packets on the network. High buffer size allows to store this burst and not lose packets.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

ip2IfMaxGprsTxQueue		1.3.6.1.4.1.164.3.1.6.7.1.1.82
Max GPRS Tx Queue buffer size, measured in msec (milliseconds). Low buffer size may cause the buffer to overflow and discard packets in case of burst of packets on the network. High buffer size allows to store this burst and not lose packets.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

ip2IfV23HD		1.3.6.1.4.1.164.3.1.6.7.1.1.83
This parameter shows whether V.23 Half Duplex Modem Protocol is enabled on the bundle.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), enable(3)

ip2IfModemProtocolMode		1.3.6.1.4.1.164.3.1.6.7.1.1.84
This octet string contains the mode of each Modem Protocol used on the bundle. For each protocol one octet will be used. Octet #1 will be used for V.22 Protocol. Octet #2, #3, #4... are reserved for future protocols. Octet #1 values: 0 - Not Applicable 1 - VBD: Voice Band Data. 2 - Relay: Pulse Code Modulated (PCM) data is sent via the bundle. For V.22: This MIB object is relevant only when ip2IfModemCalls = relay (4).
Status: current	Access: read-create
OBJECT-TYPE
	OCTET STRING

ip2IfCdisCngDetectionTime		1.3.6.1.4.1.164.3.1.6.7.1.1.85
When working with CDIS (Call DIScrimination method) or CNG (Comfort Noise Generation): The time in msec that the device will detect 1100Hz & 2100Hz signals on the line before switching to modem or fax. For Vmux: the values will be in steps of 10 msec.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

ip2IfSuperTandemBitMask		1.3.6.1.4.1.164.3.1.6.7.1.1.86
This MIB object enables controlling the Time Slot/Channel rate. Valid values: 1 - FF HEX Each BIT represents 1/8 of the TS. Example: 7E (0111 1110) means that 6/8 of the TS (the center ones) are masked and data will be Tx/Rx only through them. This MIB object is relevant only when Super Tandem is enabled.
Status: current	Access: read-create
OBJECT-TYPE
	OCTET STRING

ip2IfVbdSwitchbackTime		1.3.6.1.4.1.164.3.1.6.7.1.1.87
Time in msec required for the DSP to switch back from VBD (Voice Band Data) to Voice. For Vmux: the values will be in steps of 30 msec.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

ip2IfCallerIdTxGain		1.3.6.1.4.1.164.3.1.6.7.1.1.88
The gain value in dBm units used for transmitting the Caller ID signal on the bundle.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

ip2IfCallerIdRxGain		1.3.6.1.4.1.164.3.1.6.7.1.1.89
The gain value in dBm units of the Caller ID signal received on the bundle.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

ip2IfUdpMuxMethod		1.3.6.1.4.1.164.3.1.6.7.1.1.90
This parameter determines according to which field the multiplexing is made: srcPort (2) - multiplexing according to the UDP Source Port (Dest=0x085e). This should be the default value, for backwards compatibility. destPort (3) - multiplexing according to the UDP Destination Port (standard multiplexing). The UDP Source and Destination ports' range is determined according to ip2IfUdpMuxMethod value: For srcPort (2) the range is 1-7000 For destPort (3) the range is 49152-65535.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	srcPort(2), destPort(3)

ip2IfCallerIdDetection		1.3.6.1.4.1.164.3.1.6.7.1.1.91
Enable/Disable Caller ID Detection for this bundle.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), enable(3)

ip2IfWap		1.3.6.1.4.1.164.3.1.6.7.1.1.92
Enable/Disable WAP (Wireless Application Protocol) for this bundle. WAP allows users to access the internet from wireless devices.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), enable(3)

ip2IfTDMFrameBytes		1.3.6.1.4.1.164.3.1.6.7.2
The number of TDM bytes to be placed in a single IP frame payload.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

ip2IfTosValue		1.3.6.1.4.1.164.3.1.6.7.3
The TOS value to write in the IP frame.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

ip2IfVlanTagging		1.3.6.1.4.1.164.3.1.6.7.4
VLAN support. no - No support to VLAN. yes - 4 VLAN bytes will be added to the frame.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(1), yes(2)

ip2IfVlanID		1.3.6.1.4.1.164.3.1.6.7.5
VLAN ID.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

ip2IfVlanPriority		1.3.6.1.4.1.164.3.1.6.7.6
Frame priority.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

ip2IfStatTable		1.3.6.1.4.1.164.3.1.6.7.7
Channels (Bundles) Statistics Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Ip2IfStatEntry

ip2IfStatEntry		1.3.6.1.4.1.164.3.1.6.7.7.1
IP Statistics per bundle
Status: current	Access: not-accessible
OBJECT-TYPE
	Ip2IfStatEntry

ip2IfStatChIndex		1.3.6.1.4.1.164.3.1.6.7.7.1.1
The channel index, which is actualy the bundle ID.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ip2IfStatSeqErrors		1.3.6.1.4.1.164.3.1.6.7.7.1.2
Number of events that the sequence number of an incoming Frame causes a transition from the 'sync' state to the 'out of sequence' state.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ip2IfStatBufUnderflows		1.3.6.1.4.1.164.3.1.6.7.7.1.3
Number of events that the buffer underflows. This records the count of the number of events the Receive (Eth to TDM) buffer underflows. In the case of a continuous underflow caused by a loss of Frame flow, a single buffer underflow should be counted.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ip2IfStatBufOverflows		1.3.6.1.4.1.164.3.1.6.7.7.1.4
Number of events that the buffer overflows. This records the count of the number of events the Receive (Eth to TDM) buffer overflows.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ip2IfStatTxOnTimeInterval		1.3.6.1.4.1.164.3.1.6.7.7.1.5
Number of frames that were transmitted due to time interval elapse. The user can choose to Tx the Frame when it reaches the Max size or when the packetizing time interval elapses. The packetizing time interval is the interval in msec that it takes to build a Max. size frame.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ip2IfStatTxOnMaxSize		1.3.6.1.4.1.164.3.1.6.7.7.1.6
Number of frames that were transmitted due to reaching max. frame size. The user can choose to Tx the Frame when it reaches the Max size or when the packetizing time interval elapses.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ip2IfStatRxSignaling		1.3.6.1.4.1.164.3.1.6.7.7.1.7
Number of signaling frames that were received.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ip2IfStatRxVoice		1.3.6.1.4.1.164.3.1.6.7.7.1.8
Number of voice frames that were received.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ip2IfStatRxHdlc		1.3.6.1.4.1.164.3.1.6.7.7.1.9
Number of HDLC frames that were received.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ip2IfStatTxSignaling		1.3.6.1.4.1.164.3.1.6.7.7.1.10
Number of signaling frames that were transmitted.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ip2IfStatTxVoice		1.3.6.1.4.1.164.3.1.6.7.7.1.11
Number of voice frames that were transmitted.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ip2IfStatTxHdlc		1.3.6.1.4.1.164.3.1.6.7.7.1.12
Number of HDLC frames that were transmitted.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ip2IfStatRdnFlip		1.3.6.1.4.1.164.3.1.6.7.7.1.13
Number of redundancy flips occured. This parameter counts only flips from this bundle to the other bundle in the redundancy couple.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ip2IfFarEndTdmStatus		1.3.6.1.4.1.164.3.1.6.7.7.1.14
This variable indicates the Status of the Far-End TDM Line. It contains failure state information. The variable is a bit map represented as a sum, therefore, it can represent multiple failures simultaneously. The farEndTdmNoDefect must be set if and only if no other flag is set. The various bit positions are: 1 farEndTdmNoDefect 2 farEndTdmAIS Alarm Indication Signal 4 farEndTdmRDI Remote Defect Indication
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..6

ip2IfStatPsnTxFrames		1.3.6.1.4.1.164.3.1.6.7.7.1.15
Number of frames that were transmitted to PSN.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ip2IfStatPsnRxFrames		1.3.6.1.4.1.164.3.1.6.7.7.1.16
Number of frames that were recieved from PSN.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ip2IfStatMinJittBufLevel		1.3.6.1.4.1.164.3.1.6.7.7.1.17
The Minimum jitter buffer level (in msec).
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

ip2IfStatMaxJittBufLevel		1.3.6.1.4.1.164.3.1.6.7.7.1.18
The Maximum jitter buffer level (in msec).
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

ip2IfStatRecommendedJittBufSize		1.3.6.1.4.1.164.3.1.6.7.7.1.19
The Recommended jitter buffer Size (in msec). 0= not applicable.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

ip2IfStatPsnSeqErrors		1.3.6.1.4.1.164.3.1.6.7.7.1.20
Number of times that the sequence number of an incoming Frame indicates Loss of Frame or Out of order occured in PSN.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ip2IfStatPsnReorderFrames		1.3.6.1.4.1.164.3.1.6.7.7.1.21
Number of times that Frames had been reordered in PSN.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ip2IfStatMinRoundTripDelay		1.3.6.1.4.1.164.3.1.6.7.7.1.22
The minimum Round Trip delay (in msec). 0= not applicable.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

ip2IfStatMaxRoundTripDelay		1.3.6.1.4.1.164.3.1.6.7.7.1.23
The maximum Round Trip delay (in msec). 0= not applicable.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

ip2IfStatAvrRoundTripDelay		1.3.6.1.4.1.164.3.1.6.7.7.1.24
The avarage Round Trip delay (in msec). 0= not applicable.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

ip2IfStatFrameTrackDupDrop		1.3.6.1.4.1.164.3.1.6.7.7.1.25
The number of packets dropped due to being duplicated. (duplicated packet means a packet that has the same sequential number as a packet being received previously).
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ip2IfStatFrameTrackMissing		1.3.6.1.4.1.164.3.1.6.7.7.1.26
The number of packets that are missing. (Missing packet means an expected packet- according to the current sequential number - that was not received).
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ip2IfStatFrameTrackLongSerMiss		1.3.6.1.4.1.164.3.1.6.7.7.1.27
The longest series of consecutive missing sequential numbers. Missing sequential numbers represent missing packets that was expected to be received successively.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ip2IfStatTxMeasuredSilence		1.3.6.1.4.1.164.3.1.6.7.7.1.28
This object shows the percentage of Silence that was measured by the device for the current bundle in the transmitted payload. Relevant values: 0..100, 255. Default value is 50. 0 means that there is no silence on the line. 100 means that there is only silence. In this case, there might be no traffic. 255 - value for not applicable or unknown.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ip2IfStatRxMeasuredSilence		1.3.6.1.4.1.164.3.1.6.7.7.1.29
This object shows the percentage of Silence that was measured by the device for the current bundle in the received payload. Relevant values: 0..100, 255. Default value is 50. 0 means that there is no silence on the line. 100 means that there is only silence. In this case, there might be no traffic. 255 - value for not applicable or unknown.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ip2IfStatHdlcCrcErr		1.3.6.1.4.1.164.3.1.6.7.7.1.30
This counter indicates the number of received HDLC frames with CRC errors.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ip2IfStatHdlcAlignErr		1.3.6.1.4.1.164.3.1.6.7.7.1.31
This counter indicates the number of received HDLC frames with alignment errors.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ip2IfStatHdlcOversize		1.3.6.1.4.1.164.3.1.6.7.7.1.32
This counter indicates the number of received HDLC frames longer than 1470.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ip2IfStatHdlcUndersize		1.3.6.1.4.1.164.3.1.6.7.7.1.33
This counter indicates the number of received HDLC frames shorter than 4.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ip2IfStatHdlcAbort		1.3.6.1.4.1.164.3.1.6.7.7.1.34
This counter indicates the number of received HDLC frames with abort indication.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ip2IfStatRxCorrectFrames		1.3.6.1.4.1.164.3.1.6.7.7.1.35
Number of received correct frames.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ip2IfStatHdlcErroredFrames		1.3.6.1.4.1.164.3.1.6.7.7.1.36
Number of received errored HDLC frames.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ip2IfRateLimit		1.3.6.1.4.1.164.3.1.6.7.8
The maximum rate permitted to transfer via the network portin Mbps.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

ip2IfPortTable		1.3.6.1.4.1.164.3.1.6.7.9
Port Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Ip2IfPortEntry

ip2IfPortEntry		1.3.6.1.4.1.164.3.1.6.7.9.1
Application layer configuration per Port
Status: current	Access: not-accessible
OBJECT-TYPE
	Ip2IfPortEntry

ip2IfPortIndex		1.3.6.1.4.1.164.3.1.6.7.9.1.1
The Port index, which is actualy the ifIndex.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ip2IfPortUsage		1.3.6.1.4.1.164.3.1.6.7.9.1.2
This parameter indicates the usage of the port (percents).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ip2IfPortMask		1.3.6.1.4.1.164.3.1.6.7.9.1.3
This parameter defines whether Agent will mask port's alarms and statistics or not.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), dontMask(2), mask(3)

ip2IfPortTotalThroughput		1.3.6.1.4.1.164.3.1.6.7.9.1.4
This parameter indicates the total Throughput of the port in bps.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ip2IfCurrentStatTable		1.3.6.1.4.1.164.3.1.6.7.10
Channels (Bundles) Current Statistics Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Ip2IfCurrentStatEntry

ip2IfCurrentStatEntry		1.3.6.1.4.1.164.3.1.6.7.10.1
IP Current Statistics per bundle
Status: current	Access: not-accessible
OBJECT-TYPE
	Ip2IfCurrentStatEntry

ip2IfCurrentStatSeqErrors		1.3.6.1.4.1.164.3.1.6.7.10.1.1
Number of seconds that the sequence number of an incoming Frame causes a transition from the 'sync' state to the 'out of sequence' state in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ip2IfCurrentStatBufUnderflows		1.3.6.1.4.1.164.3.1.6.7.10.1.2
Number of seconds that the buffer underflows in the current interval. This records the count of the number of seconds the Receive (Eth to TDM) buffer underflows in the current interval. In the case of a continuous underflow caused by a loss of Frame flow, a single buffer underflow should be counted.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ip2IfCurrentStatBufOverflows		1.3.6.1.4.1.164.3.1.6.7.10.1.3
Number of seconds that the buffer overflows in the current interval. This records the count of the number of seonds the Receive (Eth to TDM) buffer overflows in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ip2IfCurrentStatMaxDelayVar		1.3.6.1.4.1.164.3.1.6.7.10.1.4
The maximum deviation from the center of the buffer (in msec) for the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ip2IfCurrentStatMinJittBufLevel		1.3.6.1.4.1.164.3.1.6.7.10.1.5
The Minimum jitter buffer level (in msec) for the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

ip2IfCurrentStatMaxJittBufLevel		1.3.6.1.4.1.164.3.1.6.7.10.1.6
The Maximum jitter buffer level (in msec) for the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

ip2IfCurrentStatTxErrFrameSec		1.3.6.1.4.1.164.3.1.6.7.10.1.7
The number of seconds in which errored frames were transmitted during the current interval. The error may be one of the following: CRC error, Alignment error, Oversized frame, Undersized frame, Aborted frame.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ip2IfIntervalStatTable		1.3.6.1.4.1.164.3.1.6.7.11
Channels (Bundles) Interval Statistics Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Ip2IfIntervalStatEntry

ip2IfIntervalStatEntry		1.3.6.1.4.1.164.3.1.6.7.11.1
IP Interval Statistics per bundle
Status: current	Access: not-accessible
OBJECT-TYPE
	Ip2IfIntervalStatEntry

ip2IfIntervalStatIndex		1.3.6.1.4.1.164.3.1.6.7.11.1.1
The Interval index, which is actualy the Interval number.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ip2IfIntervalStatSeqErrors		1.3.6.1.4.1.164.3.1.6.7.11.1.2
Number of seconds that the sequence number of an incoming Frame causes a transition from the 'sync' state to the 'out of sequence' state in the selected interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ip2IfIntervalStatBufUnderflows		1.3.6.1.4.1.164.3.1.6.7.11.1.3
Number of seconds that the buffer underflows in the selected interval. This records the count of the number of seconds the Receive (Eth to TDM) buffer underflows in the selected interval. In the case of a continuous underflow caused by a loss of Frame flow, a single buffer underflow should be counted.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ip2IfIntervalStatBufOverflows		1.3.6.1.4.1.164.3.1.6.7.11.1.4
Number of seconds that the buffer overflows in the selected interval. This records the count of the number of seconds the Receive (Eth to TDM) buffer overflows in the selected interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ip2IfIntervalStatMaxDelayVar		1.3.6.1.4.1.164.3.1.6.7.11.1.5
The maximum size of the buffer (in 10's of usec) in the selected interval.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ip2IfIntervalStatMinJittBufLevel		1.3.6.1.4.1.164.3.1.6.7.11.1.6
The Minimum jitter buffer level (in msec) for the selected interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

ip2IfIntervalStatMaxJittBufLevel		1.3.6.1.4.1.164.3.1.6.7.11.1.7
The Maximum jitter buffer level (in msec) for the selected interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

ip2IfIntervalStatTxErrFrameSec		1.3.6.1.4.1.164.3.1.6.7.11.1.8
The number of seconds in which errored frames were transmitted during the selected interval. The error may be one of the following: CRC error, Alignment error, Oversized frame, Undersized frame, Aborted frame.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ip2IfLogEvents		1.3.6.1.4.1.164.3.1.6.7.12
This parameter defines whether all Jitter Buffer and Sequence Number events will enter to Log File, or enter those events to Log file in one minute steps.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), all(2), oneMinStep(3)

ip2IfEthSwitchMode		1.3.6.1.4.1.164.3.1.6.7.13
This parameter defines whether Eth Switch is in VLAN Tagged mode.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), unTagged(2), tagged(3)

alarmStatusTrap		1.3.6.1.4.1.164.6.1.3.0.5
The trap is sent whenever there is a transition from a no alarm state to a state with at least one active alarm.
Status: current	Access: read-write
NOTIFICATION-TYPE

systemTrap		1.3.6.1.4.1.164.6.1.3.0.6
This trap alerts of major problems in the device.
Status: current	Access: read-write
NOTIFICATION-TYPE

alarmLOS		1.3.6.1.4.1.164.6.1.3.0.7
This trap indicates Loss Of Signal.
Status: current	Access: read-write
NOTIFICATION-TYPE

alarmLOF		1.3.6.1.4.1.164.6.1.3.0.8
This trap indicates Loss Of Frame.
Status: current	Access: read-write
NOTIFICATION-TYPE

channelOperStatusTrap		1.3.6.1.4.1.164.6.1.3.0.9
This trap is sent upon any change in one or more channels.
Status: current	Access: read-write
NOTIFICATION-TYPE

alarmAIS		1.3.6.1.4.1.164.6.1.3.0.10
This trap indicates AIS.
Status: current	Access: read-write
NOTIFICATION-TYPE

alarmRDI		1.3.6.1.4.1.164.6.1.3.0.11
This trap indicates RDI.
Status: current	Access: read-write
NOTIFICATION-TYPE

alarmFEBE		1.3.6.1.4.1.164.6.1.3.0.12
This trap indicates FEBE.
Status: current	Access: read-write
NOTIFICATION-TYPE

localConnStatusTrap		1.3.6.1.4.1.164.6.1.3.0.13
This trap is sent upon a change in Local connectivity of Bundle connection.
Status: current	Access: read-write
NOTIFICATION-TYPE

remoteConnStatusTrap		1.3.6.1.4.1.164.6.1.3.0.14
This trap is sent upon a change in Remote connectivity of Bundle connection.
Status: current	Access: read-write
NOTIFICATION-TYPE

bundleConnectionStatusTrap		1.3.6.1.4.1.164.6.1.3.0.15
This trap is sent upon any change in the connectivity status of a Bundle (ip2IfOperStatus). The ifAlias index is the ifIndex of the bundle that its status has been changed.
Status: current	Access: read-write
NOTIFICATION-TYPE

broadbandIf		1.3.6.1.4.1.164.3.1.6.8
OBJECT IDENTIFIER

bdbandConfig		1.3.6.1.4.1.164.3.1.6.8.1
OBJECT IDENTIFIER

prtPhyPerfHistory		1.3.6.1.4.1.164.3.1.6.8.2
OBJECT IDENTIFIER

prtBdbandIndTable		1.3.6.1.4.1.164.3.1.6.8.1.1
The Indication Signal table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtBdbandIndEntry

prtBdbandIndEntry		1.3.6.1.4.1.164.3.1.6.8.1.1.1
An entry in the Indication Signal table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtBdbandIndEntry

prtBdbandCnfgIdx		1.3.6.1.4.1.164.3.1.6.8.1.1.1.1
This object indicates the Idx of the Agent Cnfg the following objects refer. 255=Temporary Cnfg (when relevant, Set is done only to this configuration). For Agents that support only one configuration, this object will be constant=1.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtBdbandIdx		1.3.6.1.4.1.164.3.1.6.8.1.1.1.2
This object indicates a unique port or interface number. For numbering, see product's spec. For some products, the numbering can equal ifIndex.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtBdbandIndSig		1.3.6.1.4.1.164.3.1.6.8.1.1.1.3
This object indicates a unique Indication Signal. ais(1) = AIS = Alarm Indication Signal. rdi(2) = RDI = Remote Defect Indication.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ais(1), rdi(2), aisAndRdi(3)

prtBdbandIndEvent		1.3.6.1.4.1.164.3.1.6.8.1.1.1.4
This object indicates a unique Event that can cause the Indication Signal. slm(2) = SLM = Signal Label Mismatch eed(4) = EED = Excessive Error Defect pathTrace(5) = the end-to-end source/destination of information is wrong. lom(6) = LOM = Loss of Multiframe. lop(7) = LOP = Loss of Pointer. slu(8) = SLU = Signal Label Unequipped.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), slm(2), fail(3), eed(4), pathTrace(5), lom(6), lop(7), slu(8)

prtBdbandIndSigEnable		1.3.6.1.4.1.164.3.1.6.8.1.1.1.5
This object allows user to define if the event specified by prtBdbandIndEvent will cause creation of the Indication Signal specified by prtBdbandIndSig or not. disable - will not enable causing the signal enable - will enable causing the signal.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), enable(3)

prtBdbandRowStatus		1.3.6.1.4.1.164.3.1.6.8.1.1.1.6
Creation/Deletion of rows in the table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

prtPhyConfigTable		1.3.6.1.4.1.164.3.1.6.8.1.2
The Phy Config table. Used now for Phy25.6 Mbps.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtPhyConfigEntry

prtPhyConfigEntry		1.3.6.1.4.1.164.3.1.6.8.1.2.1
An entry in the Phy Config table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtPhyConfigEntry

prtPhyTimeElapsed		1.3.6.1.4.1.164.3.1.6.8.1.2.1.1
The number of seconds that have elapsed since the beginning of the current error-measurement period.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..899

prtPhyValidIntervals		1.3.6.1.4.1.164.3.1.6.8.1.2.1.2
The number of previous intervals for which valid data was collected. The value will be 96 unless the interface was brought online within the last 24 hours, in which case the value will be the number of complete 15 minute since the interface has been online.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..96

prtPhyCurrentTable		1.3.6.1.4.1.164.3.1.6.8.2.1
The 25.6 Mbps Section/Line Current table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtPhyCurrentEntry

prtPhyCurrentEntry		1.3.6.1.4.1.164.3.1.6.8.2.1.1
An entry in the 25.6 Mbps Line Current table. ifIndex of the line 25.6 Mbps layer of type 25.6 Mbps.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtPhyCurrentEntry

prtPhyCurrentLOS		1.3.6.1.4.1.164.3.1.6.8.2.1.1.1
The counter associated with the number of Loss Of Sync seconds, encountered by a 25.6 Mbps interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtPhyCurrentLSV		1.3.6.1.4.1.164.3.1.6.8.2.1.1.2
The counter associated with the number of Line symbol violation seconds, encountered by a 25.6 Mbps interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtPhyCurrentUAS		1.3.6.1.4.1.164.3.1.6.8.2.1.1.3
The counter associated with the number of UAS encountered by a 25.6 Mbps interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtPhyCurrentSES		1.3.6.1.4.1.164.3.1.6.8.2.1.1.4
The counter associated with the number of SES encountered by a 25.6 Mbps interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtPhyCurrentES		1.3.6.1.4.1.164.3.1.6.8.2.1.1.5
The number of Errored Seconds, encountered by a 25.6 Mbps interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtPhyCurrentStatus		1.3.6.1.4.1.164.3.1.6.8.2.1.1.6
The statuses of the current interval: 0 - O.K. 1 - The link has been switched by a redundancy mechanism. 2 - Module is in/out. 4 - Empty - card is out.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(4)

prtPhyCurrentLOF		1.3.6.1.4.1.164.3.1.6.8.2.1.1.7
The number of Loss of Frames, encountered by an interface in the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtPhyIntervalTable		1.3.6.1.4.1.164.3.1.6.8.2.2
The Line Interval table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtPhyIntervalEntry

prtPhyIntervalEntry		1.3.6.1.4.1.164.3.1.6.8.2.2.1
An entry in the 25.6 Mbps Line Interval table. ifIndex of the line 25.6 Mbps layer of type 25.6 Mbps.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtPhyIntervalEntry

prtPhyIntervalNumber		1.3.6.1.4.1.164.3.1.6.8.2.2.1.1
A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..96

prtPhyIntervalLOS		1.3.6.1.4.1.164.3.1.6.8.2.2.1.2
The counter associated with the number of Loss Of Sync seconds , encountered by a 25.6 Mbps interface in one of the previous 96, individual 15 minute intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtPhyIntervalLSV		1.3.6.1.4.1.164.3.1.6.8.2.2.1.3
The counter associated with the number of line symbol violation seconds , encountered by a 25.6 Mbps interface in one of the previous 96, individual 15 minute intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtPhyIntervalUAS		1.3.6.1.4.1.164.3.1.6.8.2.2.1.4
The counter associated with the number of UAS encountered by a 25.6 Mbps interface in one of the previous 96, individual 15 minute intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtPhyIntervalSES		1.3.6.1.4.1.164.3.1.6.8.2.2.1.5
The counter associated with the number of SES encountered by a 25.6 Mbps interface in one of the previous 96, individual 15 minute intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtPhyIntervalES		1.3.6.1.4.1.164.3.1.6.8.2.2.1.6
The number of Errored Seconds, encountered by a 25.6 Mbps interface in one of the previous 96, individual 15 minute intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtPhyIntervalStatus		1.3.6.1.4.1.164.3.1.6.8.2.2.1.7
The statuses of the current interval: 0 - O.K. 1 - The link has been switched by a redundancy mechanism. 2 - Module is in/out. 4 - Empty - card is out.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(4)

prtPhyIntervalLOF		1.3.6.1.4.1.164.3.1.6.8.2.2.1.8
The number of Loss of Frames, encountered by an interface in one of the previous 96, individual 15 minute intervals.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

webranger		1.3.6.1.4.1.164.11.7.2
OBJECT IDENTIFIER

wrSysConfig		1.3.6.1.4.1.164.11.7.2.1
OBJECT IDENTIFIER

wrBraodcastCtrlCmd		1.3.6.1.4.1.164.11.7.2.1.1
This parameter is a command to the webranger CPU. It enables blocking or forwarding broadcast frames, which may cause a trigger to a connection. block (1) - blocks the broadcast frames. forward (2) - forwards the broadcast frames. blockLinkPropagation (3) - blocks the broadcast frames to the links, tx to the LAN.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	block(1), forward(2), blockLinkPropagation(3)

wrFrSelfLearningMode		1.3.6.1.4.1.164.11.7.2.1.2
This parameter enables the webranger to learn the DLCi's configuration and maintanance protocol. off - will get the configuration by setting it. on - disables configuration and start self learning.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(1), on(2)

wrGratuitousArp		1.3.6.1.4.1.164.11.7.2.1.3
This parameter enables/disables the Gratuitous ARP feature. When enabled, the feature means: when receiving ARP with sender's Source IP Address that already exists in the ARP table - replace MAC Address with sender's Source MAC Address.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(2), enable(3)

wrIpRouterInfo		1.3.6.1.4.1.164.11.7.2.2
OBJECT IDENTIFIER

wrConfigIpDhcp		1.3.6.1.4.1.164.11.7.2.2.1
OBJECT IDENTIFIER

wrConfigIpDNS		1.3.6.1.4.1.164.11.7.2.2.2
OBJECT IDENTIFIER

wrDhcpAction		1.3.6.1.4.1.164.11.7.2.2.1.1
Activating (disable/enable) DHCP server operation. Since DHCP Server and DHCP Relay cannot reside in same device, DHCP Relay may be enabled (per interface), only if server action is disabled. For some devices, this object is used in order to enable/disable the DHCP Client. See device SDS.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(2), enable(3)

wrDhcpTable		1.3.6.1.4.1.164.11.7.2.2.1.2
A list of DHCP entries. The number of entries is up to DHCP current entries, according to the WEBRANger model.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WrDhcpEntry

wrDhcpEntry		1.3.6.1.4.1.164.11.7.2.2.1.2.1
DHCP parameters per entry of the DHCP table.
Status: current	Access: not-accessible
OBJECT-TYPE
	WrDhcpEntry

wrDhcpLowIpAddress		1.3.6.1.4.1.164.11.7.2.2.1.2.1.1
DHCP Low Ip Address.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

wrDhcpHighIpAddress		1.3.6.1.4.1.164.11.7.2.2.1.2.1.2
DHCP High Ip Address.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

wrDhcpIpMaskAddress		1.3.6.1.4.1.164.11.7.2.2.1.2.1.3
IP mask Address.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

wrDhcpDefaultGateway		1.3.6.1.4.1.164.11.7.2.2.1.2.1.4
Default Gateway's IP Address.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

wrDhcpPrimaryDNS		1.3.6.1.4.1.164.11.7.2.2.1.2.1.5
Primary DNS.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

wrDhcpSecondaryDNS		1.3.6.1.4.1.164.11.7.2.2.1.2.1.6
Secondary DNS.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

wrDhcpInterface		1.3.6.1.4.1.164.11.7.2.2.1.2.1.7
The IP addresse allocation is done according to the interface type from which the DHCP request arrives.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	all(1), lan1(2), lan2(3), anyLan(4), wan(5)

wrDhcpRowStatus		1.3.6.1.4.1.164.11.7.2.2.1.2.1.8
This attribute allows to create/delete a row in this table. For creating a row, the NMS should set wrDhcpRowStatus.id = active(1). For destroying a row, the NMS should set: wrDhcpStatus.id = destroy(6). Only rows with status active(1) are relevant. The only possible supported RowStatus vaules are active (1) and destroy (6).
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

wrDhcpIpAddressLeaseTime		1.3.6.1.4.1.164.11.7.2.2.1.2.1.9
Allocated IP Address lease time in seconds. A zero value specifies no time limitation.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

wrDhcpPoolName		1.3.6.1.4.1.164.11.7.2.2.1.2.1.10
DHCP pool name - string with max length of 10 characters
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString	Size(1..10)

wrDhcpTftpServerIp		1.3.6.1.4.1.164.11.7.2.2.1.2.1.11
DHCP pool - TFTP-server IP Address.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

wrDhcpConfigFileName		1.3.6.1.4.1.164.11.7.2.2.1.2.1.12
TFTP-name of the configuration File Name for DHCP pool.
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString	Size(1..50)

dhcpPoolAllocTable		1.3.6.1.4.1.164.11.7.2.2.1.3
A list of DHCP Pool Allocation entries. Each entry (row) consist of a single IP Address belonging to DHCP pool whose lowest IP address is dhcpPoolAllocLowIpAddress. This IP address may be offered for leasing, or may already be leased (in use) by Host it's MacAddress is dhcpPoolAllocMacAddress. Time left for leasing period is indicated by dhcpPoolAllocTimeLeft. All posible statuses of IP address are indicated and controlled by dhcpPoolAllocFlags
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DhcpPoolAllocEntry

dhcpPoolAllocEntry		1.3.6.1.4.1.164.11.7.2.2.1.3.1
DHCP Pool Allocation parameters per entry of the DHCP Pool Allocation table.
Status: current	Access: not-accessible
OBJECT-TYPE
	DhcpPoolAllocEntry

dhcpPoolAllocLowIpAddress		1.3.6.1.4.1.164.11.7.2.2.1.3.1.1
Lowest IP address of this pool, value eqaul to wrDhcpLowIpAddress for the pool.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

dhcpPoolAllocLeasingIpAddress		1.3.6.1.4.1.164.11.7.2.2.1.3.1.2
Single IP Address belonging to dhcp pool whose Lowest Ip Address is dhcpPoolAllocLowIpAddress. This IP address may be offered for leasing or may be leased by Host its MacAddress is dhcpPoolAllocMacAddress. All posible statuses of IP address are indicated by dhcpPoolAllocFlags
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

dhcpPoolAllocMacAddress		1.3.6.1.4.1.164.11.7.2.2.1.3.1.3
MAC Address to which the IP address has been leased
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

dhcpPoolAllocTimeLeft		1.3.6.1.4.1.164.11.7.2.2.1.3.1.4
IP address leasing time left in seconds
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

dhcpPoolAllocFlags		1.3.6.1.4.1.164.11.7.2.2.1.3.1.5
These flags indicates status of each IP address. User may change value to free, via dhcpPoolAllocFreeCmd
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), free(2), inUse(3), offered(4), forbidden(5)

dhcpPoolAllocFreeCmd		1.3.6.1.4.1.164.11.7.2.2.1.3.1.6
Setting this attribute to On (3), will enforce the agent to Free this entry. The Agent will change the value of this MIB object to off(2) automatically, after performing the command. Setting this object to off(2), will do nothing
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

dhcpRelayTable		1.3.6.1.4.1.164.11.7.2.2.1.4
A list of DHCP relay entries.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DhcpRelayEntry

dhcpRelayEntry		1.3.6.1.4.1.164.11.7.2.2.1.4.1
DHCP Relay parameters per entry of the DHCP relay table.
Status: current	Access: not-accessible
OBJECT-TYPE
	DhcpRelayEntry

dhcpRelayAction		1.3.6.1.4.1.164.11.7.2.2.1.4.1.1
Setting this attribute to enable (3), will enable DHCP Relay action for this interface (Only if DHCP Server is disabled for device - wrDhcpAction=disable). dhcpRelayServerIpAddressaddress should not be 0.0.0.0 when enable is set
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(2), enable(3)

dhcpRelayServerIpAddress		1.3.6.1.4.1.164.11.7.2.2.1.4.1.2
DHCP Server IP Address.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

dhcpRelayMaxHop		1.3.6.1.4.1.164.11.7.2.2.1.4.1.3
Maximum number of hops till DHCP Server. upper limit is 16 hops
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

wrDhcpPort		1.3.6.1.4.1.164.11.7.2.2.1.5
This parameter defines the port that DHCP flow will be actiavted.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), all(2), outOfBand(3), lan1(4), lan2(5)

dhcpClientTable		1.3.6.1.4.1.164.11.7.2.2.1.6
A list of DHCP client entries.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DhcpClientEntry

dhcpClientEntry		1.3.6.1.4.1.164.11.7.2.2.1.6.1
DHCP Client parameters per entry of the DHCP Client table.
Status: current	Access: not-accessible
OBJECT-TYPE
	DhcpClientEntry

dhcpClientAction		1.3.6.1.4.1.164.11.7.2.2.1.6.1.1
This parameter default value is enable(3). Setting this attribute to disable (2), will disable DHCP Client action for this interface. This parameter can be changed to disable (2) only (it cannot be changed from disable to enable).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(2), enable(3)

dhcpClientServerIpAddress		1.3.6.1.4.1.164.11.7.2.2.1.6.1.2
DHCP Server IP Address.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

dhcpClientLeaseExpirationTime		1.3.6.1.4.1.164.11.7.2.2.1.6.1.3
This parameter holds the time (in minutes) left until lease expiration.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

dhcpClientStatus		1.3.6.1.4.1.164.11.7.2.2.1.6.1.4
This parametr displays the DHCP status.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

dhcpIfClientTable		1.3.6.1.4.1.164.11.7.2.2.1.7
DHCP client entries for each Interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DhcpIfClientEntry

dhcpIfClientEntry		1.3.6.1.4.1.164.11.7.2.2.1.7.1
DHCP Clients per entry of the DHCP Interface Client table.
Status: current	Access: not-accessible
OBJECT-TYPE
	DhcpIfClientEntry

dhcpIfClientIpAddress		1.3.6.1.4.1.164.11.7.2.2.1.7.1.2
DHCP Client IP Address.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

dhcpIfClientRowStatus		1.3.6.1.4.1.164.11.7.2.2.1.7.1.3
The row status used for creating, modifying, and deleting instances of the columnar objects in the dhcpIfClientTable. For Vmux Devices, it will be possible only to Delete instances. The addition of Clients will be done automatically by the Server according to Network messages that are sent by the Clients; not via SNMP. In order to Delete a Client, this MIB object should be set to: destroy (6).
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

dhcpServerAction		1.3.6.1.4.1.164.11.7.2.2.1.8
This variable enables the operator to perform one of the specified actions on the Server. deleteAllClients (3) is an option that is used for a device functioning as a server. It will remove all the clients from all the interfaces of the device. When the operation is complete, the agent will return a noOp (2) value.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noOp(2), deleteAllClients(3)

wrDNSRelayAction		1.3.6.1.4.1.164.11.7.2.2.2.1
When Enabled, device will act as a DNS Relay: whenever the device receives a DNS request from its host, it will forward it to the DNS server as if the request was initiated by the device itself. The reply from the DNS server is forwarded by the device to the host as if the device was answering the request.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), enable(3)

wrConfigIpxRouterInfo		1.3.6.1.4.1.164.11.7.2.3
OBJECT IDENTIFIER

wrAutoLearnLanIpxNets		1.3.6.1.4.1.164.11.7.2.3.1
Activating (disable/enable) the auto-learn operation.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(2), enable(3)

wrLanIpxNetTable		1.3.6.1.4.1.164.11.7.2.3.2
Lan IPX nets Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WrLanIpxNetEntry

wrLanIpxNetEntry		1.3.6.1.4.1.164.11.7.2.3.2.1
IPX Nets per frame type & LAN port. The table entries will be created by the agent
Status: current	Access: not-accessible
OBJECT-TYPE
	WrLanIpxNetEntry

wrLanifIndex		1.3.6.1.4.1.164.11.7.2.3.2.1.1
LAN port ifIndex.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

wrLanIpxFrameType		1.3.6.1.4.1.164.11.7.2.3.2.1.2
Frame Type
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	t8023(1), ethernet(2), t8022(3), snap(4)

wrIpxNetAddress		1.3.6.1.4.1.164.11.7.2.3.2.1.3
Net address per Frame Type & LAN port.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

wrDialInIpxNet		1.3.6.1.4.1.164.11.7.2.3.3
Net address through a link.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

ripSapIfConfTable		1.3.6.1.4.1.164.11.7.2.3.4
A list of Interfaces which require separate configuration in RIP/SAP.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RipSapIfConfEntry

ripSapIfConfEntry		1.3.6.1.4.1.164.11.7.2.3.4.1
A Single Routing Domain in a single Subnet.
Status: current	Access: not-accessible
OBJECT-TYPE
	RipSapIfConfEntry

ripSapIfConfIfIndex		1.3.6.1.4.1.164.11.7.2.3.4.1.1
The interface ifIndex.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ripSapIfConfMode		1.3.6.1.4.1.164.11.7.2.3.4.1.2
The ifIndex RIP/SAP mode.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	off(1), on(2)

ripSapIfConfStatus		1.3.6.1.4.1.164.11.7.2.3.4.1.3
This attribute allows to create/delete a row in this table. For creating a row, the NMS should set ripSapIfConfStatus.id1 = active(1). For destroying a row, the NMS should set: ripSapIfConfStatus.id1 = destroy(6). Only rows with status active(1) are relevant. The only possible supported RowStatus vaules are active (1) and destroy (6).
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

wrInterface		1.3.6.1.4.1.164.11.7.2.4
OBJECT IDENTIFIER

wrIpAddressTable		1.3.6.1.4.1.164.11.7.2.4.1
Link IP addresses Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WrIpAddressEntry

wrIpAddressEntry		1.3.6.1.4.1.164.11.7.2.4.1.1
Ip Address per Link
Status: current	Access: not-accessible
OBJECT-TYPE
	WrIpAddressEntry

wrIpIfIndex		1.3.6.1.4.1.164.11.7.2.4.1.1.1
Port interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

wrIpAddress		1.3.6.1.4.1.164.11.7.2.4.1.1.2
Link IP Address.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

wrIpMask		1.3.6.1.4.1.164.11.7.2.4.1.1.3
Link IP mask Address.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

wrIpRowStatus		1.3.6.1.4.1.164.11.7.2.4.1.1.4
This attribute allows to create/delete a row in this table. For creating a row, the NMS should set wrIpRowStatus.id1 = active(1). For destroying a row, the NMS should set: wrIpRowStatus.id1 = destroy(6). Only rows with status active(1) are relevant. The only possible supported RowStatus vaules are active (1) and destroy (6).
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

wrSpoofingTable		1.3.6.1.4.1.164.11.7.2.4.2
Spoofing Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WrSpoofingEntry

wrSpoofingEntry		1.3.6.1.4.1.164.11.7.2.4.2.1
Spoofing per Link
Status: current	Access: not-accessible
OBJECT-TYPE
	WrSpoofingEntry

wrSpoofingIfIndex		1.3.6.1.4.1.164.11.7.2.4.2.1.1
Port interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

wrSpoofingAction		1.3.6.1.4.1.164.11.7.2.4.2.1.2
Spoofing action is applied by bit code: enable : bit 0 set (disable: bit 0 is 0) keepAlive : bit 1 ... : bit 2 and so on. For the above example, to set spoofing to keepAlive action, the object's value will be 3 = [ 2**0 + 2**1 ] Only the Remote WEBRANger will accept this object ! -------
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

wrSpoofingAgingStation		1.3.6.1.4.1.164.11.7.2.4.2.1.3
Aging time of stations list, in min. The agent 'translates' the time entered in minutes, to 10 min. resolution, as follows: 1..10 min - 10 min 11..20 min - 20 min and so on... 0 is not a valid value. Only the Remote WEBRANger will accept this object ! ----------------
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

wrSpoofingRowStatus		1.3.6.1.4.1.164.11.7.2.4.2.1.4
This attribute allows to create/delete a row in this table. For creating a row, the NMS should set wrSpoofingRowStatus.id1 = active(1). For destroying a row, the NMS should set: wrSpoofingRowStatus.id1 = destroy(6). Only rows with status active(1) are relevant. The only possible supported RowStatus vaules are active (1) and destroy (6).
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

wrLanIfTable		1.3.6.1.4.1.164.11.7.2.4.3
Link IP addresses Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WrLanIfEntry

wrLanIfEntry		1.3.6.1.4.1.164.11.7.2.4.3.1
Ip Address per Link
Status: current	Access: not-accessible
OBJECT-TYPE
	WrLanIfEntry

wrLanIfIndex		1.3.6.1.4.1.164.11.7.2.4.3.1.1
Port interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

wrLanBridgeRouterMode		1.3.6.1.4.1.164.11.7.2.4.3.1.2
This parameter indicates whether the link is Bridge or Router and specifies the Router's type.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unknown(1), bridge(2), ipRouter(3), ipxRouter(4), ipAndIpxRouter(5), bRouter(6), ipBrouter(7), ipxBrouter(8), ipAndIpxBrouter(9), bridgeAndStp(10)

wrLanIfState		1.3.6.1.4.1.164.11.7.2.4.3.1.3
The LAN is disabled or enabled. For LAN 2 it can be also 'redundancy'.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(2), enable(3), redundancy(4)

wrLanIfRdnTimeout		1.3.6.1.4.1.164.11.7.2.4.3.1.4
LAN Redundancy Timeout in seconds. Applicable when wrLanIfState=redundancy.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

wrSyncCnfgTable		1.3.6.1.4.1.164.11.7.2.4.4
Configuration table for Async interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WrSyncCnfgEntry

wrSyncCnfgEntry		1.3.6.1.4.1.164.11.7.2.4.4.1
Configuration table
Status: current	Access: not-accessible
OBJECT-TYPE
	WrSyncCnfgEntry

wrSyncIfIndex		1.3.6.1.4.1.164.11.7.2.4.4.1.1
Sync interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

wrSyncClkMode		1.3.6.1.4.1.164.11.7.2.4.4.1.2
Clock Mode.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), manual(2), program(3)

wrSyncClkRate		1.3.6.1.4.1.164.11.7.2.4.4.1.3
Clock Rate in. Rate can be changed if Clock Mode is Program only.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), r16(2), r32(3), r48(4), r64(5), r96(6), r128(7), r256(8), r768(9)

wrFrCnfgTable		1.3.6.1.4.1.164.11.7.2.4.5
Configuration table for Fr parameters that do not exist in RFC2115.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WrFrCnfgEntry

wrFrCnfgEntry		1.3.6.1.4.1.164.11.7.2.4.5.1
Configuration entry for Fr parameters that do not exist in RFC2115.
Status: current	Access: not-accessible
OBJECT-TYPE
	WrFrCnfgEntry

wrFrDlciLearningMode		1.3.6.1.4.1.164.11.7.2.4.5.1.1
This parameter enables the webranger to learn the DLCi's configuration and maintanance protocol for the current interface. off - the WR will read the user's configuration for this interface. on - the WR will begin self learning of the current interface's maintanance protocol and DLCIs.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

wrFrCllmMessages		1.3.6.1.4.1.164.11.7.2.4.5.1.2
This parameter enables/disables the Webranger to Tx/Rx CLLM (Consolidated Link Layer Management) messages via DLCI 1023. The CLLM messages are link layer control messages. They can be used for example in cases of congestion. The CLLM message contains a code for cause of congestion and list of all DLCIs that should act to reduce data transmission.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(2), enable(3)

dacsMux		1.3.6.1.4.1.164.3.3
OBJECT IDENTIFIER

systemDacsMux		1.3.6.1.4.1.164.3.3.1
OBJECT IDENTIFIER

mdlDacsMux		1.3.6.1.4.1.164.3.3.2
OBJECT IDENTIFIER

prtDacsMux		1.3.6.1.4.1.164.3.3.3
OBJECT IDENTIFIER

genDacsMux		1.3.6.1.4.1.164.3.3.4
OBJECT IDENTIFIER

sysSa		1.3.6.1.4.1.164.3.3.1.1
OBJECT IDENTIFIER

sysHub		1.3.6.1.4.1.164.3.3.1.2
OBJECT IDENTIFIER

sysStatus		1.3.6.1.4.1.164.3.3.1.3
OBJECT IDENTIFIER

sysCurrentAlr		1.3.6.1.4.1.164.3.3.1.4
OBJECT IDENTIFIER

sysBufferAlr		1.3.6.1.4.1.164.3.3.1.5
OBJECT IDENTIFIER

sysConfig		1.3.6.1.4.1.164.3.3.1.6
OBJECT IDENTIFIER

sysDbase		1.3.6.1.4.1.164.3.3.1.7
OBJECT IDENTIFIER

sysSaSwchStatus		1.3.6.1.4.1.164.3.3.1.1.1
This object indicates the status of the switches on the SA unit. Each switch is represented by a bit. The status is a sum of 2**n, according to the bits. For SMODs products see modem's specification. For DXC product see the following: There are 4 switches: bit 0 SP-PAR (LSB) '1' - Default parameters bit 1 PSWRD '1' - Password=default '0' - Password=user selected bit 2 DB-INIT '1' - DB initiated with default '0' - DB initiated with NVRAM contents bit 3 PC-SP (MSB) '1' - Management by terminal only '0' - Management by NMS Example: If SP-PAR and PSWRD bits are set ('1'), the value will be 3 (2**1 + 2**0). When the status of the switches is unknown, the value of this object will be 255.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysSaSwRevision		1.3.6.1.4.1.164.3.3.1.1.2
This object indicates the Software revision of the system.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

sysSaHwVersion		1.3.6.1.4.1.164.3.3.1.1.3
This object indicates the Hardware version of the system.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

sysSaPorts		1.3.6.1.4.1.164.3.3.1.1.4
This object indicates the ports that are present in the system. Each possible port is represented by a bit. The value of this object is a sum of 2**n, n=number of bits. '1' - means that the port exists '0' - means that the port does not exist For detailed bit assignment, see product's spec. Bit 0 = LSB When this object is not relevant, the value will be 0. In some cases, this object may represent ports configuration of the system AND its far-end unit.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysSaReadSwch		1.3.6.1.4.1.164.3.3.1.1.5
This object indicates wether the configuration will be read from the DIP switches on the SA (stand alone) unit. Each switch is represented by a bit. If the bit is 1: the configuration will be read from the HW switch position. If the bit is 0: the configuration will be read from the SW user configuration. The DIP switches are different in each of the RAD devices. In the Tiny Router (starting from the LSB) the following switches exist: Bit 0: WAN Loop Bit 1: LAN Full Duplex (When LAN AUI connector, it is SQE) Bit 2: PPP (When WAN 4 Wire connector, it is LONG) Bit 3: IP Learn
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

sysSaBuActivePort		1.3.6.1.4.1.164.3.3.1.1.6
This object shows through which port the traffic is flowing (the current Active Port) when the Backup mechanism exists. When No Backup exists in the device, the value should be: notApplicable(1).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), e1T1orSerial(2), eth(3), primary(4), secondary(5), third(6), fourth(7)

sysChas		1.3.6.1.4.1.164.3.3.1.2.1
OBJECT IDENTIFIER

chassTotalNoOfSlt		1.3.6.1.4.1.164.3.3.1.2.1.1
This object indicates the number of physical slots in the Hub chassis.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

chassTotalNoOfIoSlt		1.3.6.1.4.1.164.3.3.1.2.1.2
This object indicates the total number of physical IO slots in the chassis, (not all slots must be occupied and active).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

chassTotalNoOfPsSlt		1.3.6.1.4.1.164.3.3.1.2.1.3
This object indicates the number of physical Power Supply slots in the chassis.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

chassTotalNoOfClSlt		1.3.6.1.4.1.164.3.3.1.2.1.4
This object indicates the number of physical Common Logic slots in the chassis.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

chassTotalNoOfMlSlt		1.3.6.1.4.1.164.3.3.1.2.1.5
This object indicates the number of physical Main Link slots in the chassis (Kmux).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysDcl		1.3.6.1.4.1.164.3.3.1.2.2
OBJECT IDENTIFIER

sysDclTable		1.3.6.1.4.1.164.3.3.1.2.2.1
All the entries of this table are identical (have the same value) for all the configurations (1..255) except the TmpCnfg. The write operation into the Table Objects is valid only for the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SysDclEntry

sysDclEntry		1.3.6.1.4.1.164.3.3.1.2.2.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SysDclEntry

sysDclCnfgIdx		1.3.6.1.4.1.164.3.3.1.2.2.1.1.1
This object indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg. This object is identical for all the configurations (1..255). Only the TmpCnf(255) might have a different value. For devices that work on line with NMS (no Temp configuration in NMS), Get and Set will be performed with index value of sysDclCnfgIdx = 1.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

sysDclRedundancy		1.3.6.1.4.1.164.3.3.1.2.2.1.1.2
DCL redundancy desired state.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

sysDclActiveCl		1.3.6.1.4.1.164.3.3.1.2.2.1.1.3
Active desired DCL. When 'auto' is selected, the system automatically selects the active DCL.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	auto(1), dclA(2), dclB(3)

sysDclFlipDelay		1.3.6.1.4.1.164.3.3.1.2.2.1.1.4
If one DCL flip occurred and a second one should be performed, the time from the previous flip is checked. If the time is shorter than the delay specified here, the system should delay the flip operation until time reaches the specified delay. For DXC the values are 1 minute to 4 minutes (1..4). For Optimux-155-1 and Optimux-155-3 the values are: 0...60 Sec. 0 means No Delay.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

sysDclFlipUponStnClk		1.3.6.1.4.1.164.3.3.1.2.2.1.1.5
This object allows user to decide (yes/no) if Agent should Flip from one DCL card to another, when there is Station Clock Fail in the Online DCL card.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), no(2), yes(3)

sysDclChFailThreshold		1.3.6.1.4.1.164.3.3.1.2.2.1.1.6
This object indicates the number of failed channels that will trigger the redundancy procedure.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

sysDclChPriority		1.3.6.1.4.1.164.3.3.1.2.2.1.1.7
This object indicates the Priority for all the channels in the Main Access (Common Logic) card. Each channel is represented by 1 bit. The order of the bits in each byte is from Right to Left (LSB Bit to MSB) starting from BIT 0: 7 6 5 4 3 2 1 0 Channel no. 1 is represented by bit 0. Channel no. 2 is represented by bit 1. Channel no. n is represented by bit n-1. The value of the bit shows the priority. For bit value = 1, Priority = High. For bit value = 0, Priority = Low.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysDclConfigDownloadSrc		1.3.6.1.4.1.164.3.3.1.2.2.1.1.8
In case of mismatch between the 2 CL card's configuration, the user can decide which card has the suitable configuration. The selected configuration will be downloaded from card A to card B if the value is dclA(2) or from card B to card A if the value is dclB(3). off(1) is used by part of the devices. In this case, after operation ends - value should be automatically set to off(1), which is the default state.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(1), dclA(2), dclB(3)

sysDclSwDownloadSrc		1.3.6.1.4.1.164.3.3.1.2.2.1.1.9
In case of mismatch between the 2 CL card's software, the user can decide which card has the suitable SW. The selected SW will be downloaded from card A to card B if the value is dclA(2) or from card B to card A if the value is dclB(3). off(1) is used by part of the devices. In this case, after operation ends - value should be automatically set to off(1), which is the default state.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(1), dclA(2), dclB(3)

sysDclRedundancyStatus		1.3.6.1.4.1.164.3.3.1.2.2.1.1.10
Bit map representing current Redundancy Status. bit 0 - Indicates mismatch between the 2 CL cards' Configuration bit 1 - Indicates mismatch between the 2 CL cards' Software. bit 2 - Indicates CL card A Absence. bit 3 - Indicates CL card B Absence. bit 4 - Indicates Loss of Communication between the 2 CL cards. bit 5 - Indicates mismatch between the 2 CL cards' Hardware. bit 6 - Indicates Configuraton update is in process. bit 7 - Indicates Software update is in process.
Status: current	Access: read-only
OBJECT-TYPE
	BITS	cnfgMismatch(0), swMismatch(1), cardAAbsent(2), cardBAbsent(3), lossOfCommunication(4), hwMismatch(5), cnfgUpdate(6), swUpdate(7)

sysDclOnline		1.3.6.1.4.1.164.3.3.1.2.2.2
The active Dcl card of the agent.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	dclA(1), dclB(2)

sysDclCopyDbTable		1.3.6.1.4.1.164.3.3.1.2.2.3
This table enables to copy a cofiguration from the Offline Dcl to the Online Dcl.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SysDclCopyDbEntry

sysDclCopyDbEntry		1.3.6.1.4.1.164.3.3.1.2.2.3.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SysDclCopyDbEntry

sysDclCopyDbIdx		1.3.6.1.4.1.164.3.3.1.2.2.3.1.1
This object indicates the Idx of the Cnfg(1..255) being accessed.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

sysDclCopyDbCmd		1.3.6.1.4.1.164.3.3.1.2.2.3.1.2
When this command is sent to the agent, on(3), the Database specified (Db Idx), will be copied from the Offline Dcl to the Online Dcl. Afterwards the value of this object will automatically change to off(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

sysDclFlipCmd		1.3.6.1.4.1.164.3.3.1.2.2.4
When the 'flip(3)' command is received by Agent, it will flip (switch) between Offline Dcl and Online Dcl cards. Afterwards the value of this object will automatically change to off(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), flip(3)

sysSDateFormat		1.3.6.1.4.1.164.3.3.1.3.1
This object indicates the date and time format used for the sysSDateAndTimeCmd and for the alarm buffer report.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ddMMYYYY(1), mmDDYYYY(2), yyyyMMDD(4)

sysSDateCmd		1.3.6.1.4.1.164.3.3.1.3.2
This object indicates the current date as it is known by the agent using its own real-time clock. The format would be as specified by the sysSDateFormat. This parameter can be set for time synchronization between the NMS and the Agent. * For KM-2100 V1 and FCD-T1/E1 - the string should contain '/' signs between day, month and year. Example: 12/08/1998. * For DXC and rest of the products - the string should contain '-' signs between day, month and year. Example: 12-08-1998. The day value will be in the range: 1..31. The month value will be in the range: 1..12. The year value will be in the range: 1996..2050 for products supporting the '-' format.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

sysSTimeCmd		1.3.6.1.4.1.164.3.3.1.3.3
This object indicates the current time as it is known by the agent using its own real-time clock. This parameter can be set for time synchronization between the NMS and the Agent. The string should contain ':' signs between hour, minute and second. Example: 11:05:58.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

sysSActiveCnfg		1.3.6.1.4.1.164.3.3.1.3.4
This object specifies the configuration number, that is currently active and running.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysSEditCnfg		1.3.6.1.4.1.164.3.3.1.3.5
This object indicates the unique configuration number that is currently loaded into the tmp working space for manipulation and update operations. Value of 255 means no config. is under editing process.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysSEditBy		1.3.6.1.4.1.164.3.3.1.3.6
This entry indicates which MMI application is working on the edited config. The editing phase starts at the first modify operation and ends after a load operation.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), snmp(2), terCon1(3), terCon2(4), terInbandCon1(5), terInbandCon2(6), lcd(7)

sysSClkSrc		1.3.6.1.4.1.164.3.3.1.3.7
This entry indicates the source of the system clock.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	master(1), fallback(2), internal(3), ml(4)

sysSAlrStatus		1.3.6.1.4.1.164.3.3.1.3.8
Indicates the current alarm state only for system level. This object will be : - critical(7): when there is at least one active (ON) critical alarm . - major (3): when there is no active critical alarm, but there is at least one active (ON) major alarm . - minor (4): when there is no active major or critical alarm, but there is at least one active minor alarm. - warning (6): when there is no active major, critical or minor alarm, but there is at least one active warning alarm. - event (5): when there is no active alarm of another type, but there is at least one active event alarm. - off(2): when there is no active (ON) alarm (since last clear operation).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), major(3), minor(4), event(5), warning(6), critical(7)

sysSAlrStatusAll		1.3.6.1.4.1.164.3.3.1.3.9
Indicates the current alarm state including all levels: system, card, port. - critical(7): when there is at least one active (ON) critical alarm . - major (3): when there is no active critical alarm, but there is at least one active (ON) major alarm . - minor (4): when there is no active major or critical alarm, but there is at least one active minor alarm. - warning (6): when there is no active major, critical or minor alarm, but there is at least one active warning alarm. - event (5): when there is no active alarm of another type, but there is at least one active event alarm. - off(2): when there is no active (ON) alarm (since last clear operation).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), major(3), minor(4), event(5), warning(6), critical(7)

sysSTestStatus		1.3.6.1.4.1.164.3.3.1.3.10
Indicates the current test status (for all levels: system, card, port). This attribute will be set to: - on(3): when there is at least one test in progress on the system/card/port otherwise the value will be off(2).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), on(3)

sysSSanityCheckStatus		1.3.6.1.4.1.164.3.3.1.3.11
Upon completion of the Sanity Check process on the TmpCnfg this object will be set to: - fail(2): when there is at least one error (which is not just a warning) encountered otherwise, - warning(3): when there are only warnings otherwise, - ok(4). The value should be unknown(1), if the TmpCnfg was changed after the last Sanity check.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), fail(2), warning(3), ok(4)

sysSNoOfSanityCheckErr		1.3.6.1.4.1.164.3.3.1.3.12
This object indicates the number of errors/warnings discovered by the last Sanity Check process.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysSErrListTable		1.3.6.1.4.1.164.3.3.1.3.13
A table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SysSErrListEntry

sysSErrListEntry		1.3.6.1.4.1.164.3.3.1.3.13.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SysSErrListEntry

sysSErrType		1.3.6.1.4.1.164.3.3.1.3.13.1.1
The errors are recorded in the agent, in two separate lists, according to their type: error or warning.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	error(1), warning(2)

sysSErrIdx		1.3.6.1.4.1.164.3.3.1.3.13.1.2
Unique index number to identify an entry in the error or warning list . The maximum value cannot exceed the value of 'sysSNoOfSanityCheckErr' (actually, the sum of the Errors list max. index and the Warning list max. index should equal the value of'sysSNoOfSanityCheckErr').
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysSErrDescription		1.3.6.1.4.1.164.3.3.1.3.13.1.3
This object is a full text description of the sanity check error including error code, IO slot and port numbers related to the code .
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

sysSMaxNoOfCnfg		1.3.6.1.4.1.164.3.3.1.3.14
Maximum number of configurations that can be defined and stored in the DACS agent. If the DACS agent has a large capacity, the maximum will be limited to 254.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysSSelfTestResult		1.3.6.1.4.1.164.3.3.1.3.15
The test is performed by the active Common Logic card. The result will be a sum of 2**n according to the following bit convention: For DXC: bit 0 Database 1 Checksum Error (LSB) bit 1 Database 2 Checksum Error bit 2 I/O Expander Error bit 3 Counter Error bit 4 Matrix DPR Error bit 5 PS-A 5 Volt Error bit 6 PS-A 12 Volt Error bit 7 PS-B 5 Volt Error bit 8 PS-B 12 Volt Error bit 9 EPROM Failure For FCD: bit 0 I/O Expander Error (LSB) bit 1 Counter Error bit 2 EPROM Failure bit 3 Illegal Sys Config bit 4 SFIFO bit 5 EPIC Failure (ISDN) bit 6 XL Flash Fail -- for MSDSL interface bit 7 XL MITEL Fail -- for MSDSL interface bit 8 XL Framer Fail -- for MSDSL interface bit 9 XL DSP Fail -- for MSDSL interface For LRS52 - refer to product's spec When a bit is ('1'), the error exists. When NO ERROR is encountered, this object's value will be 0.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysSRelayState		1.3.6.1.4.1.164.3.3.1.3.16
Indicates the current state of the alarm relay. notApplicable - for agents that do not support this object.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), off(2), on(3)

sysSInvertedAlr		1.3.6.1.4.1.164.3.3.1.3.17
Indicates if there is any Inverted alarm at any level of the system (sys, card, port). notApplicable - for agents that do not support this object.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), no(2), yes(3)

sysSRdnFlipTable		1.3.6.1.4.1.164.3.3.1.3.18
This table includes all the Flip events due to I/O Redundancy since last Clear command of this table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SysSRdnFlipEntry

sysSRdnFlipEntry		1.3.6.1.4.1.164.3.3.1.3.18.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SysSRdnFlipEntry

sysSRdnFlipIdx		1.3.6.1.4.1.164.3.3.1.3.18.1.1
Unique index number to identify an entry in the Redundancy Flip list.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysSRdnFlipSlot		1.3.6.1.4.1.164.3.3.1.3.18.1.2
The slot number from which Flip was performed.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), notApplicable(255)

sysSRdnFlipPort		1.3.6.1.4.1.164.3.3.1.3.18.1.3
The port number from which Flip was performed. For DXC: For external ports the convention used will be: - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . For internal ports the convention used will be: - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . For MP: For external ports, the value will be as that of the port in the card. Example: external-3 -> 3 external-4 -> 4 For internal ports, the value will be 100 + the port in the card. Example: internal-1 -> 101 internal-4 -> 104 100=notApplicable (when Redundancy is at card level).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysSRdnFlipCause		1.3.6.1.4.1.164.3.3.1.3.18.1.4
The last cause that caused the Flip from the Slot (Port) of sysSRdnSlot, sysSRdnPort.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

sysSRdnFlipDate		1.3.6.1.4.1.164.3.3.1.3.18.1.5
Flip event Date. The format will be the one selected by user for sysSDateFormat.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

sysSRdnFlipTime		1.3.6.1.4.1.164.3.3.1.3.18.1.6
Flip event Time. The format will be hh:mm:ss.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

sysSRdnFlipTableClearCmd		1.3.6.1.4.1.164.3.3.1.3.19
This command, when Set to 'on', clears the Redundancy Flip table (sysSRdnFlipTable). After clear is performed, the agent will turn the value to 'off' automatically.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

sysSRdnFlipCmd		1.3.6.1.4.1.164.3.3.1.3.20
This object enables the user to send a command to the Agent, to Flip from a current Online IO card to its Redundant card. The value sent will be an Object Identifier of an entry in the sysCRdnTable. This entry defines the Redundant couple of Slots on which the Flip is applied. Setting this object, will cause the Agent to Flip from current Online card to its Redundant card. This manual flip command is applicable only for entries having Redundancy Mode=Y Cable. For Vmux: This command will cause flipping from Secondary or Third Link to the Primary Link. If the active link is the primary link, the agent will flip to the secondary link. The value sent will be the Object Identifier of the following Table: agnCBuMlTable. Agent will send the value 0 for Get.
Status: current	Access: read-write
OBJECT-TYPE
	OBJECT IDENTIFIER

sysSBusTable		1.3.6.1.4.1.164.3.3.1.3.21
This table includes data and status about the internal DXC BUS.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SysSBusEntry

sysSBusEntry		1.3.6.1.4.1.164.3.3.1.3.21.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SysSBusEntry

sysSBusPortIdx		1.3.6.1.4.1.164.3.3.1.3.21.1.1
The DXC BUS port number: - first two digits will be: (IO slot number+10) - last one/two digits will be the Bus port number, in odd numbers: port1 = 1 port2 = 3 Example: port2 of IO slot 11 will be: 213.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysSBusStatus		1.3.6.1.4.1.164.3.3.1.3.21.1.2
The Status of sysSBusPortIdx. free - not used physical - captured by the port of the card physically installed virtual - captured virtually by another port. Example: DIM port (by Destination) or by Transparent T3/E3 port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	free(1), physical(2), virtual(3)

sysSBusCapturePort		1.3.6.1.4.1.164.3.3.1.3.21.1.3
The Port that Captured the sysSBusPortIdx. - if sysSBusStatus=free, the value will be 'none'=0 - else, if sysSBusStatus=fixed, the value will be: sysSBusPortIdx - else, the value will be according to the port index that captured this Bus Port (according to DXC port index convention): - xx1, xx3, xx11, xx13, xx31, xx33, xx2..xx56(even numbers) - xx = (IO slot number+10)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysSBusUtilization		1.3.6.1.4.1.164.3.3.1.3.21.1.4
Utilization of sysSBusPortIdx resources, in percent [%].
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysSAlrAttrIndication		1.3.6.1.4.1.164.3.3.1.3.23
This object indicates the status of the Alarm Attributes for the whole device. It is a sum of 2**(Bit-1). A Bit will be '1', when any alarm in the device is Filtered/Masked/Inverted (respectively). The Bit assignment is: Bit 1: Filter (LSB) Bit 2: Mask Bit 3: Invert (MSB). Examples: - Alarms are filtered and masked but not inverted: value=3 - Alarm is Inverted (not filtered or masked): value=4 - Alarm is masked (not inverted or filtered): value=2
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysSAlrTable		1.3.6.1.4.1.164.3.3.1.4.1
List of system level current existing alarms .
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SysSAlrEntry

sysSAlrEntry		1.3.6.1.4.1.164.3.3.1.4.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SysSAlrEntry

sysSAlrIdx		1.3.6.1.4.1.164.3.3.1.4.1.1.1
An index number of the current system alarms.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysSAlrCode		1.3.6.1.4.1.164.3.3.1.4.1.1.2
This object indicates a code related to a specific alarm description. The list of codes and their related descriptions will be sent to NMS request (for display purpose) by alrGenTable.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysSAlrState		1.3.6.1.4.1.164.3.3.1.4.1.1.3
This object indicates the alarm Severity.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	event(3), minor(4), major(5), warning(6), critical(7)

sysSAlarmMask		1.3.6.1.4.1.164.3.3.1.4.1.1.4
Alarm Mask is : on/off.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), on(3)

sysSAlarmInvert		1.3.6.1.4.1.164.3.3.1.4.1.1.5
Alarm Invert is : on/off.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), on(3)

sysSAlarmOnOff		1.3.6.1.4.1.164.3.3.1.4.1.1.6
Alarm state is : on/off.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), on(3)

sysSAlarmCounter		1.3.6.1.4.1.164.3.3.1.4.1.1.7
A counter - how many times the alarm occured (ON) since last clear operation or since last Reset.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysSAlrClearCmd		1.3.6.1.4.1.164.3.3.1.4.2
Setting this attribute to ON, will enforce a clear operation on the system level alarms . Upon completion, the value will automatically change to off(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

sysSAlrClearAllCmd		1.3.6.1.4.1.164.3.3.1.4.3
Setting this attribute to ON, will enforce a clear operation on all levels alarms . Upon completion, the value will automatically change to off(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

sysSAlrMaskAll		1.3.6.1.4.1.164.3.3.1.4.4
on(3) - will cause masking of all the system level alarms. These alarms will not be sent to NMS and will not be taken into account for Alarms Status. off(2) - will unmask all system level alarms except those masked via the sysSAlrMask.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

sysSAlrMask		1.3.6.1.4.1.164.3.3.1.4.5
This object is a mask that indicates which system level alarms are masked. The masked alarms (their bit is set to '1') are neither sent to the manager, nor taken into account for alarm status and LEDs. Bit no. = Alarm code The bits that do not belong to the system level will be 0. This object is applicable only when sysSAlrMaskAll=off (otherwise all system alarms are masked). Example: When Alarms having the codes 6 and 11 are masked, the value of this object will be 840 (hex).
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(8)

sysSAlrDataUpdateCmd		1.3.6.1.4.1.164.3.3.1.4.6
on(3) - will cause Update of the Alarms Severity, Attributes and Report tables. off(2) - Upon completion, the value will automatically change to off(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

sysBufferAlrTable		1.3.6.1.4.1.164.3.3.1.5.1
List of current existing alarms (of all levels).
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SysBufferAlrEntry

sysBufferAlrEntry		1.3.6.1.4.1.164.3.3.1.5.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SysBufferAlrEntry

sysBufferAlrIdx		1.3.6.1.4.1.164.3.3.1.5.1.1.1
An index number of the current alarms.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysBufferAlrCode		1.3.6.1.4.1.164.3.3.1.5.1.1.2
This object indicates a code related to a specific alarm description. The list of codes and thir related descriptions will be known by the NMS (for display purpose) and will appear in the unit's user manual.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysBufferAlrState		1.3.6.1.4.1.164.3.3.1.5.1.1.3
This object indicates the alarm type. minor/major/warning/critical - indicates appearance of the problem and the type. event - indicates occurence of an event. off - indicates disappearance of an alarm.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), event(3), minor(4), major(5), warning(6), critical(7)

sysBufferAlrSlot		1.3.6.1.4.1.164.3.3.1.5.1.1.4
The slot number this alarm refers to. When the alarm refers to a system function OR the DACS agent is a stand-alone unit, the value will be 'notApplicable(255)'. local/remote - for OP-4 device.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	psA(1), psB(2), clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), local(20), psC(21), kmxPsA(101), kmxPsB(102), kmxMlA(103), kmxMlB(104), kmxCl(105), kmxOpt(106), kmxIO1(107), kmxIO2(108), kmxIO3(109), kmxIO4(110), kmxIO5(111), kmxIO6(112), kmxIO7(113), kmxIO8(114), kmxIO9(115), kmxIO10(116), kmxIO11(117), kmxIO12(118), remote(120), notApplicable(255)

sysBufferAlrPort		1.3.6.1.4.1.164.3.3.1.5.1.1.5
The port number this alarm refers to. If the port number is irrelevant to this alarm (if it is a system/card level alarm) the value will be 9999.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysBufferAlrDate		1.3.6.1.4.1.164.3.3.1.5.1.1.6
The date when the alarm occured. The format will be according to sysSDateFormat.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

sysBufferAlrTime		1.3.6.1.4.1.164.3.3.1.5.1.1.7
The time when the alarm occured.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

sysBufferAlrUpTime		1.3.6.1.4.1.164.3.3.1.5.1.1.8
The time when the alarm occured. This parameter holds the sysUpTime value when the alarm occured.
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

sysBufferAlrInfo		1.3.6.1.4.1.164.3.3.1.5.1.1.9
This parameter includes information about the alarm (additional to the Description).
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString

sysBufferAlrClearCmd		1.3.6.1.4.1.164.3.3.1.5.2
Setting this attribute to ON, will enforce a clear operation on the Alarms Buffer. Upon completion, the value will automatically change to off(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

sysCClkSrcTable		1.3.6.1.4.1.164.3.3.1.6.1
All the entries of this table are identical (have the same value) for all the configurations (1..255) except the TmpCnfg. For devices with more than one configuration: The write operation into the Table Objects is valid only for the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SysCClkSrcEntry

sysCClkSrcEntry		1.3.6.1.4.1.164.3.3.1.6.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SysCClkSrcEntry

sysCClkCnfgIdx		1.3.6.1.4.1.164.3.3.1.6.1.1.1
This attribute indicates the Idx of the Cnfg being accessed ; Idx of 255 relates to the TmpCnfg. It can be also a combination of the configuration number and the Card/Port/Other System index.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..2147483647

sysCClkSrcIdx		1.3.6.1.4.1.164.3.3.1.6.1.1.2
An index in the table. There are only two entries in the table. master - refers Master clock parameters fallback - refers Fallback clock parameters
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	master(1), fallback(2)

sysCClkSrcMode		1.3.6.1.4.1.164.3.3.1.6.1.1.3
This entry indicates the source the nodal timing is locked to. none - is an invalid option for Master clock. internal - is an invalid option for Fallback clock . station - is an invalid option for a stand-alone unit. lbt - loop-back timing ntr - Network Time Reference adaptive - clock locking is achieved by altering the clock according to the data load system - irrelevant when sysCClkCnfgIdx refers to System Clock. sSubSystem - SONET/SDH Sub System. recovered - clock recovery. notApplicable - for ML source of Kmux or ML Timing combinations when Master/Fallback clock are not applicable.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), internal(2), rxClk(3), station(4), lbt(5), ntr(6), adaptive(7), stationB(8), automatic(9), system(10), sSubSystem(11), recovered(12), notApplicable(255)

sysCClkSrcPrt		1.3.6.1.4.1.164.3.3.1.6.1.1.4
This entry is valid only when working in rxClk mode (for IPmux1000 this entry will be valid whe working in LBT mode). For ACE2002 in case of invalid entry the return value will be 0. For other products in case of invalid entry the return value will be 9999. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside, SP. * The SP ports will be numbered as follows: - SP port 1 : 1 - SP port 2 : 2 For external ports the convention used will be (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . For internal ports the convention used will be (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . For Kmux, the port will be according to : Slot*100+Ch. For ACE2002, LA140 and IPmux1000 (GMUX), the port will be ifIndex.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

sysCClkStationFreq		1.3.6.1.4.1.164.3.3.1.6.1.1.5
This entry indicates the frequency of the station clock when the source is 'station'. The value will be applicable only when the sysCClkSrcMode is 'station'.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), f1544Khz(2), f2048Khz(3)

sysCClkRevertiveTimeout		1.3.6.1.4.1.164.3.3.1.6.1.1.6
The time in seconds in which the system will monitor the higher level clock source, before decision to revert to that clock. In case the time is zero, revertive mode will be disabled.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

sysCClkStationIf		1.3.6.1.4.1.164.3.3.1.6.1.1.7
This entry indicates the electrical interface connected to the station clock, when the source is 'station'. The value will be applicable only when the sysCClkSrcMode is 'station'.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), g703(2), rs422(3), g703E1Unbalanced(4), g703T1(5), rs422T1(6)

sysCClkStationCableMode		1.3.6.1.4.1.164.3.3.1.6.1.1.8
This parameter indicates whether both Station clocks get their clock from the same source (Y Cable)or each one get its clock independently. The value will be applicable only when the sysCClkSrcMode is 'station'.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), normal(2), yCable(3)

sysCClkStationOutState		1.3.6.1.4.1.164.3.3.1.6.1.1.9
This parameter indicates whether station clock can send its clock to another device. The value will be applicable only when the sysCClkSrcMode is 'station'.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), disabled(2), enabled(3)

sysCClkSsmBased		1.3.6.1.4.1.164.3.3.1.6.1.1.10
This parameter indicates whether clock source will be selected based on receive clock quality, indicated in S1 byte inside SONET/SDH overhead, (encoded as SSM - Synchronization Status Messaging). It is relevant only for sysCClkSrcIdx=master. When the value is Yes, sysCClkSrcMode must be notApplicable.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), no(2), yes(3)

sysCClkSSubsystemSlot		1.3.6.1.4.1.164.3.3.1.6.1.1.11
This entry indicates the Slot from which the S Subsytem Source will be taken. The value will be applicable only when the sysCClkSrcMode is 'sSubsystem'.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), clA(3), clB(4)

sysCClkRecoveredID		1.3.6.1.4.1.164.3.3.1.6.1.1.12
This entry indicates the Recovered Clock ID. The value will be applicable only when sysCClkSrcMode is 'recovered'.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

sysCnfgTable		1.3.6.1.4.1.164.3.3.1.6.2
All the entries of this table are identical (have the same value) for all the configurations (1..255) except the TmpCnfg. The write operation into the Table Objects is valid only for the TmpCnfg entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SysCnfgEntry

sysCnfgEntry		1.3.6.1.4.1.164.3.3.1.6.2.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SysCnfgEntry

sysCnfgIdx		1.3.6.1.4.1.164.3.3.1.6.2.1.1
This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg. For Gmux2000 the range limitation (1..255) was discarded since the Idx is computed as: x 1000 + 255.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysCMatrixMode		1.3.6.1.4.1.164.3.3.1.6.2.1.2
Indicates the TS Matrix Mode: bidirectional - TS Assignment Matrix is symmetric. unidirectional - TS Assignment Matrix can be asymmetric. notApplicable - for agents that do not support this feature.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), bidirectional(2), unidirectional(3)

sysCIsdnFormat		1.3.6.1.4.1.164.3.3.1.6.2.1.3
ISDN format. This parameter controls the operation mode of the ISDN ports. te - ISDN timing is derived from the signal received from the equipment it is connected to. nt - timing of the transmit path is locked to the nodal timing source. notApplicable - for agents that do not support this feature.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), te(2), nt(3)

sysCRoutingOnEth		1.3.6.1.4.1.164.3.3.1.6.2.1.4
Mng Routing Protocol on the online CL Ethernet port, or on device Ethernet port dedicated for mangement.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), none(2), proprietary(3), rip2(4), rip1(5), rip1and2(6)

sysCAutoConfigEnable		1.3.6.1.4.1.164.3.3.1.6.2.1.5
This object enables user to enable/disable activating the Auto Configuration. When Auto Configuration is activated, the device learns its configuration Automatically from the Net it is connected to.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), enable(3)

sysCIntTsAllocMode		1.3.6.1.4.1.164.3.3.1.6.2.1.6
This object enables user to select the mode of Internal TS Allocation. static - user has to select for each Dynamic card port, the Maximum TSs expected to be connected (including future growth). This number will be allocated to the ports, so that if number of connected TSs will grow within the limits of this Maximum TS limit, no disruption of data flow will occur for other ports. dynamic- TS allocation is done dynamically according to the connected TSs. No future reservations are done. This mode may cause data disruption on other ports/slots if user will want to change the number of connected TSs for a Dynamic card port. staticOneToOne - user has to select for each Dynamic card port, the Maximum TSs expected to be connected (including future growth). In addition, the TSs themselves cannot be higher than this defined Maximum (e.g if Maximum TSs=5 user cannot selects TSs higher than 5). This mode ensures that if number of TSs grow within the limits of this Maximum TS limit, no disruption of data flow will occur for other ports AND for the selected port itself. Default=static(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), static(2), dynamic(3), staticOneToOne(4)

sysCBuPrimaryPort		1.3.6.1.4.1.164.3.3.1.6.2.1.7
This object enables the user to configure a Backup mechanism. If a backup mechanism exists, it is possible to configure the primary port. The traffic will flow via the primary port when the port functionality is OK. In Vmux-2100 device the backup mechanism is relevant for the Main Board only. The primary port can be the E1/T1/Serial port or the ETH port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noBackup(2), e1T1orSerial(3), eth(4)

sysCEnableLanOverTdm		1.3.6.1.4.1.164.3.3.1.6.2.1.8
This object enables/disables transferring traffic from the LAN port to the TDM port. It is possible to enable only part of the traffic on the TDM port for security reasons or in order to minimize the bandwidth .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enableAll(2), enableVoiceOnly(3), enableVoiceAndMng(4)

sysCSs7FisuSuppression		1.3.6.1.4.1.164.3.3.1.6.2.1.9
SS7 Suppresion is used for SS7 Spoofing. The SS7 spoofing terminates the keep alive messages from the local VMUX without sending them over the network, thus improving the bandwidth utilization. FISU means Fill in Service Unit - Keep alive that is sent when no one is talking on the line. This object enables the configuration of the SS7 Keep Alive packet % that will be discarded. Legal Values: 0 - No Suppression, 10%, 20%, 30% .. 90% Example: For a value of 10, 1 keep alive packet will be discarded out of 10 keep alive packets that were supposed to be sent over the network.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

sysCBuRecMode		1.3.6.1.4.1.164.3.3.1.6.2.1.10
Recovery Mode. This object determines if after recovery of the Primary Link (used in Vmux) it will become on-line again or not: auto - automatic. In this case, the failed Link will become on-line again after recovery, automatically. manual - In this case, the failed Link will not become on-line again after recovery but user can manually flip to this Link.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	auto(2), manual(3)

sysCRdnTable		1.3.6.1.4.1.164.3.3.1.6.3
Configuration of all Redundant I/O cards and ports. The write operation into the table objects is valid only for the TmpCnfg. A Slot/Port that have no Redundancy, will not exist in this table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SysCRdnEntry

sysCRdnEntry		1.3.6.1.4.1.164.3.3.1.6.3.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SysCRdnEntry

sysCRdnCnfgIdx		1.3.6.1.4.1.164.3.3.1.6.3.1.1
This object indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysCRdnPrimeSlot		1.3.6.1.4.1.164.3.3.1.6.3.1.2
The slot number of the Primary card of Redundancy. The Primary card should be the card that user wishes to be the online card (usually the more important one). For some Redundancy modes the importance of the redundant cards/ports is the same.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), notApplicable(255)

sysCRdnPrimePort		1.3.6.1.4.1.164.3.3.1.6.3.1.3
The port number. For DXC: For external ports the convention used will be: - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . For internal ports the convention used will be: - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . For MP: For external ports, the value will be as that of the port in the card. Example: external-3 -> 3 external-4 -> 4 For internal ports, the value will be 100 + the port in the card. Example: internal-1 -> 101 internal-4 -> 104 For IP Bundles, the value will be the Bundle ifIndex. For an IP Bundle that is in an External Device (not in this MP), the value will be: 70,000 + ifIndex of Secondary Bundle. For other products - refer to product specification. 100=notApplicable (when Redundancy is at card level).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

sysCRdnSecSlot		1.3.6.1.4.1.164.3.3.1.6.3.1.4
The slot number of the Secondary card of Redundancy matching the Primary slot.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), notApplicable(255)

sysCRdnSecPort		1.3.6.1.4.1.164.3.3.1.6.3.1.5
The port number. For DXC: For external ports the convention used will be: - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . For internal ports the convention used will be: - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . For MP: For external ports, the value will be as that of the port in the card. Example: external-3 -> 3 external-4 -> 4 For internal ports, the value will be 100 + the port in the card. Example: internal-1 -> 101 internal-4 -> 104 For IP Bundles, the value will be the Bundle ifIndex. For an IP Bundle that is in an External Device (not in this MP), the value will be: 0. For other products - refer to product specification. 100=notApplicable (when Redundancy is at card level).
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

sysCRdnMode		1.3.6.1.4.1.164.3.3.1.6.3.1.6
Redundancy Mode. DXC supports: yCable(3), singleSlotProtection(6) and dualCableParallelTx(4) MP supports: yCable(3), dualCableParallelTx(4), onePlusOne(7) and oneToOne(8). (dualCableAIS and backup were planned for MP but were not implemented). backup - will be used when a port is backup of more than one port. IPmux: onePlusOne(7) and oneToOne(8) are used for Bundle redundancy.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	dualCableAIS(2), yCable(3), dualCableParallelTx(4), backup(5), singleSlotProtection(6), onePlusOne(7), oneToOne(8), linkAggregation(9), manual(10)

sysCRdnRecMode		1.3.6.1.4.1.164.3.3.1.6.3.1.7
Recovery Mode. This object determines if after recovery of the failed Primary card/port it will become on-line again or not: auto - automatic . In this case, the failed card/port will become on-line again after recovery, automatically. manual - In this case, the failed card/port will not become on-line again after recovery. But, user can manually flip to this card/port. nonRevertive - same as manual, but here user CANNOT manually flip to this card/port. It will become on-line again, only if the Secondary/Backup card/port will fail.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	auto(2), manual(3), nonRevertive(4)

sysCRdnRecTime		1.3.6.1.4.1.164.3.3.1.6.3.1.8
Redundancy Recovery Time (sec). After switching to the current online card, the next switch can be performed only after a minimum time, indicated by this object. Valid Values: 0..300, 65535. 65535=NA. This object is applicable only when sysCRdnRecMode=auto.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

sysCRdnHwSwFlip		1.3.6.1.4.1.164.3.3.1.6.3.1.9
HW or SW decision for Redundancy Flip. This object is applicable only for sysCRdnMode=singleSlotProtection. HW - decision is by I/O card SW - decision is by CL SW.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notApplicable(1), hw(2), sw(3)

sysCRdnRowStatus		1.3.6.1.4.1.164.3.3.1.6.3.1.10
This parameter allows NMS to create/delete entries of this table. The possible supported RowStatus values are active (1) and destroy (6). For Vmux-2100 the supported values are: active (1), createAndGo (4) and destroy (6).
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

sysCRdnOnline		1.3.6.1.4.1.164.3.3.1.6.3.1.11
Status - who is the Online (current) Redundancy Slot/Port. This object shows only the Online Slot/Port regarding the Redundancy. mdlSActivity or prtGenActiveStatus of the same Slot/Port may be Offline.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), primary(2), secondary(3)

sysCRdnSwitchingMode		1.3.6.1.4.1.164.3.3.1.6.3.1.12
This object defines which Self Healing Ring (SHR) SDH ring is used: Uni Directional or BiDirectional. The type of the ring is defined according to the direction of traffic flow under normal working conditions. In Bi Directional ring, the duplex traffic is on the same path and transverses the same set of nodes for both directions of transmission. In Uni Directional ring, the duplex traffic travels over opposite path (per direction) and all the node of the ring are involved. For Uni Directional SHR Protection Switching (Single Ended Switching) is controlled by one node of the SDH ring, and does not require a protocol. For Bi Directional SHR Protection Switching (Dual Ended switching) is controlled by some nodes of the ring and requires a protocol
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notApplicable(1), biDirectional(2), uniDirectional(3), linkAggregation(4)

sysCRdnFlipUponEvent		1.3.6.1.4.1.164.3.3.1.6.3.1.13
This object allows user to define if Flip to the other port will be performed (or not), for certain possible events. Each event is represented by a bit. The value of the object is a sum of 2**n, according to the bits having '1' value. '1' - means that Flip should occur due to this event. Bit 0 (LSB) = SD (Signal Degraded). For IPmux: Bit 0 (LSB) = TDM Line LOS/LOF. Bit 1 = Sequence Number. Bit 2 = Jitter Buffer errors.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

sysCRdnLosOrLofTime		1.3.6.1.4.1.164.3.3.1.6.3.1.14
This parameter determines how much time to wait before switching, after LOF or LOS are detected on the TDM Line. For Ipmux time is counted in msec.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

sysCRdnEventsTimeWindow		1.3.6.1.4.1.164.3.3.1.6.3.1.15
This parameter determines the time window in which to count events to trigger protection switching. For Ipmux time is counted in seconds.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

sysCRdnSequenceNumberThreshold		1.3.6.1.4.1.164.3.3.1.6.3.1.16
This parameter determines the number of Sequence Number errors that should occur in the time window in order to cause switching.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

sysCRdnBufferErrorsThreshold		1.3.6.1.4.1.164.3.3.1.6.3.1.17
This parameter determines the number of Buffer undeflow/ overflow events occured in the time window that cause switching.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

sysCRdnBuffUnderrunTime		1.3.6.1.4.1.164.3.3.1.6.3.1.18
This parameter determines how much time to wait before switching, after jitter buffer underrun. Switching occurs if no frame arrives within that time. For Ipmux time is counted in msec.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

sysCRdnPrimePriority		1.3.6.1.4.1.164.3.3.1.6.3.1.19
The Primary port priority. In ETX2xx/2xxA: When selecting sysCRdnMode = manual (10), this parameter determines the forced active port: low - means that the secondary port is selected to be active high - means that the primary port is selected to be active.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notApplicable(1), low(2), high(3)

sysCRdnSecPriority		1.3.6.1.4.1.164.3.3.1.6.3.1.20
The Secondary port priority.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	notApplicable(1), low(2), high(3)

sysCRdnWTR		1.3.6.1.4.1.164.3.3.1.6.3.1.21
Redundancy Wait to Restore (sec). Valid Values: 0..999, 65535. 65535=NA. When the value <> 65535, the value of sysCRdnRecTime must be 65535.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

sysCRdnName		1.3.6.1.4.1.164.3.3.1.6.3.1.22
A textual name for the redundancy group.
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString

sysCRdnTxDownDurationUponFlip		1.3.6.1.4.1.164.3.3.1.6.3.1.23
This object defines the duration (in seconds) the active port transmission is shut down after flip occurs. The transmission is shut down and then opened again (after the duration defined by this object), in order to cause the other side to flip to the new active port. 0 = no shut-down. This object is applicable only when sysCRdnMode = oneToOne(8) and mainly when each of the links of our device is connected to a different device.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..30

sysSRdnCmdTable		1.3.6.1.4.1.164.3.3.1.3.22
This table includes commands used for IO Redundancy.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SysSRdnCmdEntry

sysSRdnCmdEntry		1.3.6.1.4.1.164.3.3.1.3.22.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SysSRdnCmdEntry

sysSRdnEnforcedChannel		1.3.6.1.4.1.164.3.3.1.3.22.1.1
This is a command to override all switching considerations and enforce use of primary/ secondary connection only. noEnforcement - cancels the state of override and goes back to usual switching considerations. Default = noEnforcement(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), noEnforcement(2), primary(3), secondary(4)

sysSRdnLockFlip		1.3.6.1.4.1.164.3.3.1.3.22.1.2
This is a command to lock the Redundancy flip for this redundancy couple. Default = off(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), off(2), on(3)

sysSRdnManualFlip		1.3.6.1.4.1.164.3.3.1.3.22.1.3
This is a command to move to manual Redundancy flip mode for this redundancy couple. Default = off(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), off(2), on(3)

sysDbaseSanityCheckCmd		1.3.6.1.4.1.164.3.3.1.7.1
Setting this attribute to on(3) will initiate the process of Sanity check on the TmpCnfg. Upon completion, the value will automatically change to off(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

sysDbaseDownloadCnfgIdxCmd		1.3.6.1.4.1.164.3.3.1.7.2
This attribute specifies the Id of the target RealCnfg to which the TmpCnfg should be transferred. Upon set command, the DACS agent will initiate the Sanity-Check process. If successful, the actual transfer will be performed. If there will be errors, the user will have to perform the command again after errors correction. The operation is valid only on configuration numbers that do not exceed sysSMaxNoOfCnfg.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..255

sysDbaseUploadCnfgIdxCmd		1.3.6.1.4.1.164.3.3.1.7.3
This attribute specifies the Id of the source Cnfg to be loaded into the TmpCnfg. Upon set operation the actual transfer will be initiated. The operation is valid only on configuration numbers that do not exceed sysSMaxNoOfCnfg.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..255

sysDbaseFlipTable		1.3.6.1.4.1.164.3.3.1.7.4
Dbase Flip time and activation for every configuration.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SysDbaseFlipEntry

sysDbaseFlipEntry		1.3.6.1.4.1.164.3.3.1.7.4.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SysDbaseFlipEntry

sysDbaseFlipIdx		1.3.6.1.4.1.164.3.3.1.7.4.1.1
This attribute indicates the Idx of the Cnfg being the target Configuration.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

sysDbaseFlipTime		1.3.6.1.4.1.164.3.3.1.7.4.1.2
This attribute indicates the time (HH:MM) when this data base will start being used by the Tmp config.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

sysDbaseFlipActivation		1.3.6.1.4.1.164.3.3.1.7.4.1.3
This attribute indicates if the Dbase flip will be activated at the time specified for this configuration (enable) or not (disable). No more than one flip should be enabled for the same time.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

mdlGen		1.3.6.1.4.1.164.3.3.2.1
OBJECT IDENTIFIER

mdlCl		1.3.6.1.4.1.164.3.3.2.2
OBJECT IDENTIFIER

mdlPs		1.3.6.1.4.1.164.3.3.2.3
OBJECT IDENTIFIER

mdlSTable		1.3.6.1.4.1.164.3.3.2.1.1
A table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MdlSEntry

mdlSEntry		1.3.6.1.4.1.164.3.3.2.1.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	MdlSEntry

mdlSSltIdx		1.3.6.1.4.1.164.3.3.2.1.1.1.1
A unique number to identify a slot position in the DACS. The Kilomux should use enumerated values starting with kmx. For IPmux100 use values 1-13, 20.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	psA(1), psB(2), clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), psC(20), kmxPsA(101), kmxPsB(102), kmxMlA(103), kmxMlB(104), kmxCl(105), kmxOpt(106), kmxIO1(107), kmxIO2(108), kmxIO3(109), kmxIO4(110), kmxIO5(111), kmxIO6(112), kmxIO7(113), kmxIO8(114), kmxIO9(115), kmxIO10(116), kmxIO11(117), kmxIO12(118), notApplicable(255)

mdlSCardType		1.3.6.1.4.1.164.3.3.2.1.1.1.2
This attribute indicates the type of the card installed in the specific slot position. Only PS's are possible in the PS slots. Only CL's are possible in the CL slots. Only IO modules are possible in the IO slots. Kmux card type start with the letter k. LA card type start with the letters la.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), empty(2), psAC(10), psDC(11), gCl1(18), gCl2(19), dCl(20), kCl(21), dcl2(22), dcl2Eth(23), kClEth(24), dcl3(25), dcl3Eth(26), d4T1(28), d8T1(29), dT1DSU(30), dT1CSU(31), dE1DSU(32), dE1LTU(33), dE1aDSU(34), dE1aLTU(35), dT1F(36), dE1F(37), d4E1(38), d8E1(39), dE1Hdsl(40), dT1Hdsl(41), dE1HdslS(42), dT1HdslS(43), d16gsdsl(44), d8sl(45), d4slStuC(46), d4slStuR(47), kML1(50), kML2(51), kML3(52), kML4(53), kML5(54), kML6(55), kML7(56), kML8(57), kML10(59), kMLF(60), kML10New(61), kML11RJ45(62), kML11FO(63), kLS1(70), kLS1New(71), kLS2(72), kTRE(80), kMBE(81), kMBENew(82), fLAN(83), kai(90), kdi(91), kdiCH(92), dHS2(100), d8U(101), d16U(102), d4HS(103), d8HS(104), kHS1(110), kHS2(111), kHSU1(112), kHSU2(113), kHS703(114), kVC1EM(130), kVC1FXO(131), kVC1FXS(132), kVC1MEM(133), kVC1MFXO(134), kVC1MFXS(135), kVC1MFXSW(136), kVC2EM(137), kVC2FXO(138), kVC2FXS(139), kVC2s1EM(140), kVC2s1FXO(141), kVC2s1FXS(142), kVC3EM(143), kVC3FXO(144), kVC3FXS(145), kVC3S0(146), kVF1EM(170), kVF1FXO(171), kVF1FXS(172), kVF3EM(173), kVF3FXO(174), kVF3FXS(175), kVF4EM(176), kVF4FXO(177), kVF4FXS(178), kVF4FXSW(179), kVF4S0(180), kVF5PbxE1(181), kVF5E1PbxSlave(182), kVF5PbxT1(183), kVF5T1PbxSlave(184), kVF5PbxE1New(185), kVF5E1PbxSlaveNew(186), kVF5PbxT1New(187), kVF5T1PbxSlaveNew(188), kVF4FXO3(189), kVF4FXS3(190), kVF4NS0(191), kVF6E1s16(192), kVF6E1s31(193), kVF6T1s12(194), kVF6T1s24(195), kVF8EM(196), kVF8FXO(197), kVF8FXS(198), dimETUR(200), dimV35(201), dimRS422(202), dimRS530(203), dimHssi(204), dimX21(205), dim10BaseT(206), dimE1(207), dim100(208), dt3G747(209), dt3(210), dt3f(211), de3(212), de3f(213), dstm1s1(214), dstm1s2(215), fSTM1(216), dstm1(217), dstm1R(218), f2stm1(219), gstm1(220), goc3(221), gstm1D(222), goc3D(223), laSUB(230), laVEM(231), laVFXO(232), laVFXS(233), laV11(234), laV24(235), laV35(236), laT1(237), laT1Vxx(238), laE1(239), laE1Vxx(240), laISDN(241), laVxx(242), laEth(243), laISDNwBU(244), laIsdnNT(245), laIsdnNTwBU(246), laIsdnTE(247), laFXSwBU(248), laFXSs(249), laFXSwBUs(250), laIsdnNTs(251), laIsdnNTwBUs(252), laIsdnTEs(253), laDp(254), laSdsl(255), laSdslDp(256), laAdslA(257), laAdslADp(258), laAdslB(259), laAdslBDp(260), laShdsl(261), laShdslDp(262), laT1b(263), laT1bDp(264), laIsdnTEwBU(265), laIsdnTEwBUs(266), laShdsl4w(267), laShdsl4wDp(268), laEthSwitch(269), serverE1(270), serverT1(271), serverE1Pw(272), serverT1Pw(273), gigabitEth(280), gigabitEth2(281), eth2(282), gigabitEth8(283), eth8(284), channelizedT3Pw1(290), cesT128(300), cesE128(301), cesT1Pw28(302), cesE1Pw28(303), vmxE1VeDe(310), vmxE1VeDi(311), vmxE1ViDe(312), vmxE1ViDi(313), vmxT1VeDe(314), vmxT1VeDi(315), vmxT1ViDe(316), vmxT1ViDi(317), vc12E1UeNe(318), vc12E1UeNi(319), vc12E1UiNe(320), vc12E1UiNi(321), vc12T1UeNe(322), vc12T1UeNi(323), vc12T1UiNe(324), vc12T1UiNi(325), vca16E1UeNe(326), vca16E1UeNi(327), vca16E1UiNe(328), vca16E1UiNi(329), vca16T1UeNe(330), vca16T1UeNi(331), vca16T1UiNe(332), vca16T1UiNi(333), vca12E1UeNe(334), vca12E1UeNi(335), vca12E1UiNe(336), vca12E1UiNi(337), vca12T1UeNe(338), vca12T1UeNi(339), vca12T1UiNe(340), vca12T1UiNi(341), vmg16E1Ue(342), vmg16E1Ui(343), vmg16T1Ue(344), vmg16T1Ui(345), vmg12E1Ue(346), vmg12E1Ui(347), vmg12T1Ue(348), vmg12T1Ui(349)

mdlSHwVer		1.3.6.1.4.1.164.3.3.2.1.1.1.3
This attribute indicates the Hardware version of the card installed in the specific slot position.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

mdlSSwVer		1.3.6.1.4.1.164.3.3.2.1.1.1.4
This attribute indicates the Software version of the card installed in the specific slot position.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

mdlSAlarmStatus		1.3.6.1.4.1.164.3.3.2.1.1.1.5
Indicates the current alarm state only for card level. This object will be set to: - critical(7): when there is at least one active (ON) critical alarm . - major (3): when there is no active critical alarm, but there is at least one active (ON) major alarm . - minor (4): when there is no active major or critical alarm, but there is at least one active minor alarm. - warning (6): when there is no active major, critical or minor alarm, but there is at least one active warning alarm. - event (5): when there is no active alarm of another type, but there is at least one active event alarm. - off(2): when there is no active (ON) alarm (since last clear operation).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), major(3), minor(4), event(5), warning(6), critical(7)

mdlSAlarmStatusAll		1.3.6.1.4.1.164.3.3.2.1.1.1.6
Indicates the current card alarm state including the lower level: card, port. This object will be set to: - critical(7): when there is at least one active (ON) critical alarm . - major (3): when there is no active critical alarm, but there is at least one active (ON) major alarm . - minor (4): when there is no active major or critical alarm, but there is at least one active minor alarm. - warning (6): when there is no active major, critical or minor alarm, but there is at least one active warning alarm. - event (5): when there is no active alarm of another type, but there is at least one active event alarm. - off(2): when there is no active (ON) alarm (since last clear operation).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), major(3), minor(4), event(5), warning(6), critical(7)

mdlSTestStatus		1.3.6.1.4.1.164.3.3.2.1.1.1.7
This attribute will be on(3) when there is at least one test running on a port of the module; otherwise the value will be off(2).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), on(3)

mdlSHwStatus		1.3.6.1.4.1.164.3.3.2.1.1.1.8
This attribute will be fail(2) when a HW FAIL exists on this module (discovered by periodic self test); otherwise the value will be ok(3).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	fail(2), ok(3)

mdlSActivity		1.3.6.1.4.1.164.3.3.2.1.1.1.9
notApplicable - when the slot is empty (no module) offline(1) - when the module is not active (redundant) online (2) - when the module is active .
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), offline(2), online(3)

mdlSAlrClearCmd		1.3.6.1.4.1.164.3.3.2.1.1.1.10
Setting this attribute to ON, will enforce a clear operation on the card level alarms . Upon completion, the value will automatically change to off(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

mdlSAlrClearAllCmd		1.3.6.1.4.1.164.3.3.2.1.1.1.11
Setting this attribute to ON, will enforce a clear operation on card and port level alarms . Upon completion, the value will automatically change to off(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

mdlSAlrMaskAll		1.3.6.1.4.1.164.3.3.2.1.1.1.12
on(3) - will cause masking of all the card level alarms. These alarms will not be sent to NMS and will not be taken into account for Alarms Status. off(2) - will unmask all card level alarms except those masked via the mdlAlrMaskTable.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

mdlSCmd		1.3.6.1.4.1.164.3.3.2.1.1.1.13
General object for any special command at card level. 0=NotApplicable, for cards that don't support this object. For KML.10(ISDN) card of KM-2100, the object will indicate Manual Call Command in Switch mode. It is applicable only when for KML.10, prtIsdnSwitchMode=manual. KML.10 valid values: '1' = noOp, will be used by agents that do not support this feature or object (old KM agents) '2' = off, Set call command mode to disconnect state. Disconnects the call. '3' = on, Set call command mode to connect state. Connects the call. For DXC IO cards, the object will be used for IO Card Reset HW command: '2' = off, this will be always the Get value for these cards. '3' = on, this is the Set command used to Reset the IO card. Upon completing the operation, the value will automatically change to off(2), by Agent. For Slots that are NOT IO Slots and for empty IO Slots, the Get value will be always '0' (NotApplicable).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

mdlSReset		1.3.6.1.4.1.164.3.3.2.1.1.1.14
Reset action to be performed on the module.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

mdlSRebuildFrame		1.3.6.1.4.1.164.3.3.2.1.1.1.15
Applicable only for KiloMux Main Link cards only. '2' = off, this will be always the Get value. '3' = on, this is the Set command used to Rebuild the Frame. Upon completing the operation, the value will automatically change to off(2), by Agent.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), off(2), on(3)

mdlSBackupSwVer		1.3.6.1.4.1.164.3.3.2.1.1.1.16
This attribute indicates the Backup Software version of the card installed in the specific slot position.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

mdlSSecondaryBackupSwVer		1.3.6.1.4.1.164.3.3.2.1.1.1.17
This attribute indicates the Secondary Backup Software version of the card installed in the specific slot position.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

mdlSPiggybackVer		1.3.6.1.4.1.164.3.3.2.1.1.1.18
This attribute indicates the Piggyback version of the card installed in the specific slot position.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString	Size(0..255)

mdlCTable		1.3.6.1.4.1.164.3.3.2.1.2
A table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MdlCEntry

mdlCEntry		1.3.6.1.4.1.164.3.3.2.1.2.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	MdlCEntry

mdlCConfigIdx		1.3.6.1.4.1.164.3.3.2.1.2.1.1
This object indicates the Configuration number (1..255) referred. Value of 255 specifies the TmpCnfg (Scratch).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

mdlCSlotIdx		1.3.6.1.4.1.164.3.3.2.1.2.1.2
This object indicates a unique number of the slot position in which the module is inserted. The Kilomux should use enumerated values starting with kmx.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	psA(1), psB(2), clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), psC(20), kmxPsA(101), kmxPsB(102), kmxMlA(103), kmxMlB(104), kmxCl(105), kmxOpt(106), kmxIO1(107), kmxIO2(108), kmxIO3(109), kmxIO4(110), kmxIO5(111), kmxIO6(112), kmxIO7(113), kmxIO8(114), kmxIO9(115), kmxIO10(116), kmxIO11(117), kmxIO12(118), notApplicable(255)

mdlCProgCardType		1.3.6.1.4.1.164.3.3.2.1.2.1.3
This object indicates the card type assigned to the specific slot in the common configuration. This object is identical for all the configurations (1..255). Only the TmpCnf(255) might have a different value. The write operation is valid only for the TmpCnfg entry.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unknown(1), empty(2), psAC(10), psDC(11), gCl1(18), gCl2(19), dCl(20), kCl(21), dcl2(22), dcl2Eth(23), kClEth(24), dcl3(25), dcl3Eth(26), d4T1(28), d8T1(29), dT1DSU(30), dT1CSU(31), dE1DSU(32), dE1LTU(33), dE1aDSU(34), dE1aLTU(35), dT1F(36), dE1F(37), d4E1(38), d8E1(39), dE1Hdsl(40), dT1Hdsl(41), dE1HdslS(42), dT1HdslS(43), d16gsdsl(44), d8sl(45), d4slStuC(46), d4slStuR(47), kML1(50), kML2(51), kML3(52), kML4(53), kML5(54), kML6(55), kML7(56), kML8(57), kML10(59), kMLF(60), kML10New(61), kML11RJ45(62), kML11FO(63), kLS1(70), kLS1New(71), kLS2(72), kTRE(80), kMBE(81), kMBENew(82), fLAN(83), kai(90), kdi(91), kdiCH(92), dHS2(100), d8U(101), d16U(102), d4HS(103), d8HS(104), kHS1(110), kHS2(111), kHSU1(112), kHSU2(113), kHS703(114), kVC1EM(130), kVC1FXO(131), kVC1FXS(132), kVC1MEM(133), kVC1MFXO(134), kVC1MFXS(135), kVC1MFXSW(136), kVC2EM(137), kVC2FXO(138), kVC2FXS(139), kVC2s1EM(140), kVC2s1FXO(141), kVC2s1FXS(142), kVC3EM(143), kVC3FXO(144), kVC3FXS(145), kVC3S0(146), kVF1EM(170), kVF1FXO(171), kVF1FXS(172), kVF3EM(173), kVF3FXO(174), kVF3FXS(175), kVF4EM(176), kVF4FXO(177), kVF4FXS(178), kVF4FXSW(179), kVF4S0(180), kVF5PbxE1(181), kVF5E1PbxSlave(182), kVF5PbxT1(183), kVF5T1PbxSlave(184), kVF5PbxE1New(185), kVF5E1PbxSlaveNew(186), kVF5PbxT1New(187), kVF5T1PbxSlaveNew(188), kVF4FXO3(189), kVF4FXS3(190), kVF4NS0(191), kVF6E1s16(192), kVF6E1s31(193), kVF6T1s12(194), kVF6T1s24(195), kVF8EM(196), kVF8FXO(197), kVF8FXS(198), dimETUR(200), dimV35(201), dimRS422(202), dimRS530(203), dimHssi(204), dimX21(205), dim10BaseT(206), dimE1(207), dim100(208), dt3G747(209), dt3(210), dt3f(211), de3(212), de3f(213), dstm1s1(214), dstm1s2(215), fstm1(216), dstm1(217), dstm1R(218), f2stm1(219), gstm1(220), goc3(221), gstm1D(222), goc3D(223), serverE1(270), serverT1(271), serverE1Pw(272), serverT1Pw(273), gigabitEth(280), gigabitEth2(281), eth2(282), gigabitEth8(283), eth8(284), channelizedT3Pw1(290), cesT128(300), cesE128(301), cesT1Pw28(302), cesE1Pw28(303), vmxE1VeDe(310), vmxE1VeDi(311), vmxE1ViDe(312), vmxE1ViDi(313), vmxT1VeDe(314), vmxT1VeDi(315), vmxT1ViDe(316), vmxT1ViDi(317), vc12E1UeNe(318), vc12E1UeNi(319), vc12E1UiNe(320), vc12E1UiNi(321), vc12T1UeNe(322), vc12T1UeNi(323), vc12T1UiNe(324), vc12T1UiNi(325), vca16E1UeNe(326), vca16E1UeNi(327), vca16E1UiNe(328), vca16E1UiNi(329), vca16T1UeNe(330), vca16T1UeNi(331), vca16T1UiNe(332), vca16T1UiNi(333), vca12E1UeNe(334), vca12E1UeNi(335), vca12E1UiNe(336), vca12E1UiNi(337), vca12T1UeNe(338), vca12T1UeNi(339), vca12T1UiNe(340), vca12T1UiNi(341), vmg16E1Ue(342), vmg16E1Ui(343), vmg16T1Ue(344), vmg16T1Ui(345), vmg12E1Ue(346), vmg12E1Ui(347), vmg12T1Ue(348), vmg12T1Ui(349)

mdlCNoOfExtPrt		1.3.6.1.4.1.164.3.3.2.1.2.1.4
Number of external ports in the programmed module of the specific slot position
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

mdlCNoOfIntPrt		1.3.6.1.4.1.164.3.3.2.1.2.1.5
Number of internal ports in the programmed module of the specific slot position.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

mdlCParam		1.3.6.1.4.1.164.3.3.2.1.2.1.6
General configuration object at card level (per configuration). NotApplicable=0, for cards that don't support this object. For D8U and D16U cards of DXC, the object will indicate the port on which BERT will be performed. The port can be one of the external ports, any of its associated B1, B2, D ports or no port of the card (None=0). For port indexes see DXC R6 spec. For Gmux-2000, this parameter used for determining the Gigabit ETH exit port
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

mdlAlr		1.3.6.1.4.1.164.3.3.2.1.3
OBJECT IDENTIFIER

mdlAlrTable		1.3.6.1.4.1.164.3.3.2.1.3.1
The list of card alarms.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MdlAlrEntry

mdlAlrEntry		1.3.6.1.4.1.164.3.3.2.1.3.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	MdlAlrEntry

mdlAlrIdx		1.3.6.1.4.1.164.3.3.2.1.3.1.1.1
A unique number to identify an entry in the alarm status table. Users should use the get next function to read this table because the indexes are not consecutive
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

mdlAlrSltIdx		1.3.6.1.4.1.164.3.3.2.1.3.1.1.2
This attribute indicates the desired slot position. The Kilomux should use enumerated values starting with kmx.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	psA(1), psB(2), clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), psC(20), kmxPsA(101), kmxPsB(102), kmxMlA(103), kmxMlB(104), kmxCl(105), kmxOpt(106), kmxIO1(107), kmxIO2(108), kmxIO3(109), kmxIO4(110), kmxIO5(111), kmxIO6(112), kmxIO7(113), kmxIO8(114), kmxIO9(115), kmxIO10(116), kmxIO11(117), kmxIO12(118)

mdlAlrCode		1.3.6.1.4.1.164.3.3.2.1.3.1.1.3
This object indicates a code related to a specific alarm description. The list of codes and their related descriptions will be sent to NMS request (for display purpose) by alrGenTable.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

mdlAlrState		1.3.6.1.4.1.164.3.3.2.1.3.1.1.4
This object indicates the card alarm severity.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	event(3), minor(4), major(5), warning(6), critical(7)

mdlAlarmMask		1.3.6.1.4.1.164.3.3.2.1.3.1.1.5
Alarm Mask is : on/off.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), on(3)

mdlAlarmInvert		1.3.6.1.4.1.164.3.3.2.1.3.1.1.6
Alarm Invert is : on/off.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), on(3)

mdlAlarmOnOff		1.3.6.1.4.1.164.3.3.2.1.3.1.1.7
Alarm state is : on/off.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), on(3)

mdlAlarmCounter		1.3.6.1.4.1.164.3.3.2.1.3.1.1.8
A counter - how many times the alarm occured (ON) since last clear operation or since last Reset.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

mdlAlrMaskTable		1.3.6.1.4.1.164.3.3.2.1.3.2
The list of card masked alarms.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MdlAlrMaskEntry

mdlAlrMaskEntry		1.3.6.1.4.1.164.3.3.2.1.3.2.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	MdlAlrMaskEntry

mdlAlrMaskSltIdx		1.3.6.1.4.1.164.3.3.2.1.3.2.1.1
This attribute indicates the desired slot position. The Kilomux should use enumerated values starting with kmx.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	psA(1), psB(2), clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), psC(20), kmxPsA(101), kmxPsB(102), kmxMlA(103), kmxMlB(104), kmxCl(105), kmxOpt(106), kmxIO1(107), kmxIO2(108), kmxIO3(109), kmxIO4(110), kmxIO5(111), kmxIO6(112), kmxIO7(113), kmxIO8(114), kmxIO9(115), kmxIO10(116), kmxIO11(117), kmxIO12(118)

mdlAlrMask		1.3.6.1.4.1.164.3.3.2.1.3.2.1.2
This object is a mask that indicates which card level alarms are masked. The masked alarms (their bit is set to '1') are neither sent to the manager, nor taken into account for alarm status and LEDs. Bit no. = Alarm code The bits that do not belong to the card level will be 0. This object is applicable only when mdlSAlrMaskAll=off (otherwise all card alarms are masked). Example: When Alarm having the code 8 is masked, the value of this object will be 100 (hex).
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(8..10)

mdlClTable		1.3.6.1.4.1.164.3.3.2.2.1
A table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MdlClEntry

mdlClEntry		1.3.6.1.4.1.164.3.3.2.2.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	MdlClEntry

mdlClIdx		1.3.6.1.4.1.164.3.3.2.2.1.1.1
This object indicates the Cl slot referred.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	clA(3), clB(4)

mdlClSwchStatus		1.3.6.1.4.1.164.3.3.2.2.1.1.2
This object indicates the status of the switches on the referred DCL card. Each switch is represented by a bit. The status is a sum of 2**n, according to the bits. There are 4 switches: bit 0 SP-PAR (LSB) '1' - Default parameters bit 1 PSWRD '1' - Password=default '0' - Password=user selected bit 2 DB-INIT '1' - DB initiated with default '0' - DB initiated with NVRAM contents bit 3 PC-SP (MSB) '1' - Management by terminal only '0' - Management by NMS Example: If SP-PAR and PSWRD bits are set ('1'), the value will be 3 (2**1 + 2**0). When the status of the switches is unknown, the value of this object will be 255.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

mdlClLastFlipDate		1.3.6.1.4.1.164.3.3.2.2.1.1.3
Date when last flip occured. The format would be as specified by the sysSDateFormat.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

mdlClLastFlipTime		1.3.6.1.4.1.164.3.3.2.2.1.1.4
Time when last flip occured.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

mdlClLastFlipCause		1.3.6.1.4.1.164.3.3.2.2.1.1.5
The cause of last flip.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

mdlPsTable		1.3.6.1.4.1.164.3.3.2.3.1
A table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MdlPsEntry

mdlPsEntry		1.3.6.1.4.1.164.3.3.2.3.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	MdlPsEntry

mdlPsIdx		1.3.6.1.4.1.164.3.3.2.3.1.1.1
This object indicates the PS card referred.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	psA(1), psB(2)

mdlPsStatus		1.3.6.1.4.1.164.3.3.2.3.1.1.2
This object indicates the status of the PS card.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notActive(1), active(2)

mdlPsTestResult		1.3.6.1.4.1.164.3.3.2.3.1.1.3
This object indicates the result of the PS card test. ok (1) - the test passed successfully. f12V (2) - 12V FAIL was detected f5V (3) - 5V FAIL was detected.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ok(1), f12V(2), f5V(3)

prtGen		1.3.6.1.4.1.164.3.3.3.1
OBJECT IDENTIFIER

prtT1E1		1.3.6.1.4.1.164.3.3.3.2
OBJECT IDENTIFIER

prtHS		1.3.6.1.4.1.164.3.3.3.3
OBJECT IDENTIFIER

prtSP		1.3.6.1.4.1.164.3.3.3.4
OBJECT IDENTIFIER

prtDim		1.3.6.1.4.1.164.3.3.3.5
OBJECT IDENTIFIER

prtI		1.3.6.1.4.1.164.3.3.3.6
OBJECT IDENTIFIER

prtHdsl		1.3.6.1.4.1.164.3.3.3.7
OBJECT IDENTIFIER

prtT3E3		1.3.6.1.4.1.164.3.3.3.8
OBJECT IDENTIFIER

prtGenParamTable		1.3.6.1.4.1.164.3.3.3.1.1
A table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtGenEntry

prtGenEntry		1.3.6.1.4.1.164.3.3.3.1.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtGenEntry

prtGenPrtIdx		1.3.6.1.4.1.164.3.3.3.1.1.1.1
This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside/external, inside/internal. In the Kilomux, the port index is calculated as follows: 100*Slot+Ch. The external Ch numbers are 1..10, and the internal Ch numbers are 11..20. In the DXC : - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: * For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 .
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtGenSlt		1.3.6.1.4.1.164.3.3.3.1.1.1.2
This attribute indicates a unique number to identify the slot where the card is inserted in. When the unit is stand-alone, this object is not applicable and 255 will be used. The Kilomux should use the enumerated starting with kmx.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), kmxMlA(103), kmxMlB(104), kmxCl(105), kmxOpt(106), kmxIO1(107), kmxIO2(108), kmxIO3(109), kmxIO4(110), kmxIO5(111), kmxIO6(112), kmxIO7(113), kmxIO8(114), kmxIO9(115), kmxIO10(116), kmxIO11(117), kmxIO12(118), standAlone(255)

prtGenExtInt		1.3.6.1.4.1.164.3.3.3.1.1.1.3
This attribute describes the type of the designated port. Exteral port is a port with a physical connector. Internal port might be of two types, one is a composite port which collects data of a few external ports into a common bandwidth (usually routed trough DS1 link); the other type is internal ports which get only part of external port data (usually a few DS0's). In the Kilomux-2100, the internal(3) value is used for composite channels or sub-channels of an ISDN Ch.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	external(2), internal(3)

prtGenIfIndex		1.3.6.1.4.1.164.3.3.3.1.1.1.4
This attribute indicates the unique interface number assigned to the port. The specific interface of this attribute is the same as the interface identified by the value of ifindex in MIB-II.If there is no interface for the specific prtIdx, the value will be '7fffffff'h.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtGenActiveStatus		1.3.6.1.4.1.164.3.3.3.1.1.1.5
This attribute describes the activity status of the port. unknown(1) indicates that the information is not supported. notUsed(2) indicates that the port is not connected according to the active config. offLine(3) indicates that the port is down (not working) due to any problem. onLine (4) indicates that the port is up (working) offLineRedundancy(5) indicates that the port is down because it is a redundant port. onLineRedundancy (6) indicates that this is a redundant port which is up and works as the active link.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), notUsed(2), offLine(3), onLine(4), offLineRedundancy(5), onLineRedundancy(6)

prtGenAlrStatus		1.3.6.1.4.1.164.3.3.3.1.1.1.6
Indicates the alarm state at port (ch) agent level. This object will be: - critical(7): when there is at least one active (ON) critical alarm . - major (3): when there is no active critical alarm, but there is at least one active (ON) major alarm . - minor (4): when there is no active major or critical alarm, but there is at least one active minor alarm. - warning (6): when there is no active major, critical or minor alarm, but there is at least one active warning alarm. - event (5): when there is no active alarm of another type, but there is at least one active event alarm. - off(2): when there is no active (ON) alarm (since last clear operation).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), major(3), minor(4), event(5), warning(6), critical(7)

prtGenTestStatus		1.3.6.1.4.1.164.3.3.3.1.1.1.7
This attribute will be on(3) when there is at least one test in progress (running) on the port; otherwise the value will be off(2).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), on(3)

prtGenTestMask		1.3.6.1.4.1.164.3.3.3.1.1.1.8
This is a mask which indicates which tests from the 'prtGenTestCmd' list are allowed for the selected port. If a specific test is allowed, its respective bit will be SET in the mask : TEST BIT ----------- --- localLoop 1 remoteLoop 2 bert 3 plb 4 inband 5 prbs 8 loop2-v54 (RLB) 9 loop3-v54 (LLB) 10 Tone injection 13 Tx-plb 14 Tx-llb 15 DTE loop (HSSI) 16 HDSL-Tx-Inband 20 HDSL-Rx-Inband 21 Monitor 22 (test port) User Line Loopback 23 Rem-Loop-on-Rem-Unit 25 LBBD 26 LB1 27 LB2 28 BERT-on-Rem-Unit 29 TS Remote Loop 30 LLB-on-Rem-Unit 31 e.g : If the return value is 3 -> 0000000000000011 -> Bits 1 & 2 are set -> the allowed tests are : local-loop remote-loop
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtGenTestCmd		1.3.6.1.4.1.164.3.3.3.1.1.1.9
Setting this object to a value as detailed furter on (except 0) will initiate a test on the specific port, if the operation is allowed (according to TestMask). If the operation is not allowed, the mux will ignore the operation. The test/s requested will be set according to the respective bit: TEST BIT ----------- --- localLoop 1 remoteLoop 2 bert 3 plb 4 inband 5 prbs 8 loop2-v54 (RLB) 9 loop3-v54 (LLB) 10 Tone injection 13 Tx-plb 14 Tx-llb 15 DTE loop (HSSI) 16 HDSL-Tx-Inband 20 HDSL-Rx-Inband 21 Monitor 22 (test port) User Line Loopback 23 Rem-Loop-on-Rem-Unit 25 LBBD 26 LB1 27 LB2 28 BERT-on-Rem-Unit 29 TS Remote Loop 30 LLB-on-Rem-Unit 31 e.g : If the requested value is 3 -> 0000000000000011 -> Bits 1 & 2 are set -> the requested tests are : local-loop remote-loop Setting this object to stop (value=0 ; all bits are 0), will stop all the user requested tests running on the selected port; it will NOT stop the tests initiated by the system.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtGenTestRunning		1.3.6.1.4.1.164.3.3.3.1.1.1.10
This object indicates which tests are running currently on the selected port (initiated by user and/or by the system). If a specific test is currently running on the port, its respective bit will be SET: TEST BIT ----------- --- localLoop 1 remoteLoop 2 bert 3 plb 4 llb 5 txInband 6 rxInband 7 prbs 8 loop2-v54 (RLB) 9 loop3-v54 (LLB) 10 DDS DSU loop 11 DDS CSU loop 12 Tone injection 13 Tx-plb 14 Tx-llb 15 DTE loop (HSSI) 16 Local DTE loop (HSSI)17 Local Line loop (HSSI)18 Remote Line loop (HSSI)19 HDSL-Tx-Inband 20 HDSL-Rx-Inband 21 Monitor 22 (test port) User Line Loopback 23 Network Line Loopback 24 Rem-Loop-on-Rem-Unit 25 LBBD 26 LB1 27 LB2 28 BERT-on-Rem-Unit 29 TS Remote Loop 30 LLB-on-Rem-Unit 31 e.g : If the return value is 3 -> 0000000000000011 -> Bits 1 & 2 are set -> the running tests are : local-loop remote-loop llb (Bit 5) - can be initiated by system only!
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtGenType		1.3.6.1.4.1.164.3.3.3.1.1.1.11
This object describes the type of the selected port. idsl - applicable for external ports of HS-U cards (of DXC) when interface is LT-1.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), t1(2), e1(3), hs(4), t1Csu(5), t1Dsu(6), e1Ltu(7), e1Dsu(8), hdsl(9), sp(10), t1F(11), e1F(12), dim(13), isdn(14), t3(15), e3(16), t3f(17), e3f(18), idsl(19), stm1(20), vc4(21), vc12(22), msdsl(23), vc11(24), vc3(25), soh(26), eth(27), shdsl(28), other(255)

prtGenInterfaceType		1.3.6.1.4.1.164.3.3.3.1.1.1.12
This attribute indicates a unique HW interface type of the selected port. Examples: - for T1 cards: DSU, CSU - for E1 cards: DSU, LTU - for HS cards: v35, rs422, x21 etc...
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

prtGenAlrClearCmd		1.3.6.1.4.1.164.3.3.3.1.1.1.13
Setting this attribute to ON, will enforce a clear operation on the port level alarms . Upon completion, the value will automatically change to off(2). noOp - will be used by agents that do not support this feature or object.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noOp(1), off(2), on(3)

prtGenAlrMaskAll		1.3.6.1.4.1.164.3.3.3.1.1.1.14
on(3) - will mask all the alarms of the selected port off(2)- will unmask all alarms of the selected port except the ones selected by the prtAlrMaskTable. noOp - will be used by agents that do not support this feature or object.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noOp(1), off(2), on(3)

prtGenParamStatus		1.3.6.1.4.1.164.3.3.3.1.1.1.15
This object indicates Status of parameters specific to the selected port. - For a port that has no special status or is supported by prtSExHsfStatTable - 1 Octet: 00hex - For HS cards (Dxc cards) - 1 octet: Bit 7 (MSB)..Bit 2 = 0 (NA) Bit 0 and 1 indicates RTS control signal state: Bit 1: '1'=active ; '0'=notActive Bit 0 (LSB): '1'=unknown ; '0'=NA - For HS-U/1 external port (MP card, used in FCD-M) - 1 Octet: Bit 7 6 5 4 3 2 1 0 LSB |________| |__| |__| spare modem sync modem: 00 = other sync: 00 = not sync 01 = unknown 01 = sync 10 = ASMi-31/2 10 = reserved 11 = reserved 11 = reserved - For VC-6, VC-12, VC-12/6 external ports - 1 Octet : Bit 7 (MSB)..Bit 2 = 0 (NA) Bit 1: Tx Signaling '1'=On ; '0'=Off Bit 0 (LSB): Rx Signaling '1'=On ; '0'=Off - For VC-2/R2(FXS) external ports - 1 Octet : Bit - 7 6 5 4 3 2 1 0 |_| |_________| Call Call State Direction Bit 7 (MSB) and Bit 6 : Call Direction 00 - Incoming 01 - Outgoing Bit 5..Bit 0: Call State 000000 - Idle 000001 - Seized 000010 - Both-Way Conflict 000011 - Seizure Ack 000100 - Answered 000101 - Clear Backward 000110 - Clear Forward 000111 - Blocked 001000 - Fault 001001 - Fault 3 001010 - Fault 4 001011 - Fault 5 001100 - Fault 6 001101 - Fault 7 - For ML-20 external port - 3 Octets : - 1 MS Octet will represent the Real Rate used: Bit - 7 6 5 4 3 2 1 0 |___| |_______| spare Rate Valid values: 0..31, meaning 0..31x64Kbps Invalid values: 32..255. - 2 LS Octets will represent the Status of 7 Control Signals: Signal - --- CTS DSR DCD RJ TM DTR RTS Bit - 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 Octet - 2 3 (LS) '---' will always have the value 00 Rest of the Signals (2 bits each) can have the following values: 00=NA ; 01=Unused ; 10=Off ; 11=On - For ML-H/E1, ML-H/1/E1, ML-H/S/E1 internal port - 1 Octet Bit - 7 6 5 4 3 2 1 0 |___________| spare Mode of Operation Mode of Operation: '1'=Central ; '0'=Remote - For KM2100, KVF.5 cards - indicates the status of A and B signaling for each internal channel. 1 Octet: Bit - 7 6 5 4 3 2 1 0 |_____| |_| |_| spare B A Bit 0 (LSB) and Bit 1 : A status Bit 2 and Bit 3 : B status 00 - Off 01 - On 11 - Unknown - For FCD-W, NETWORK and USER ports - 1 Octet Status of Control Signals: '1'=On ; '0'=Off or when not applicable Bit - 7 6 5 4 3 2 1 0 Bit 7 (MSB) - Signal Loss (applicable only for G.703 interface) Bit 6 - CONTROL (applicable only for X.21 interface) Bit 5 - INDICATION (applicable only for X.21 interface) Bit 4 - DSR (applicable only for V.35 interface) Bit 3 - RTS (applicable only for V.35 interface) Bit 2 - CTS (applicable only for V.35 interface) Bit 1 - DTR (applicable only for V.35 interface) Bit 0 - DCD (applicable only for V.35 interface) - For DXC R6 , D8U, D16U External ports - 1 Octet Bit 7 6 5 4 3 2 1 0 LSB |________| |__| |__| spare modem sync modem: 00 = other sync: 00 = not sync 01 = unknown 01 = sync 10 = ASMi-31/2 10 = reserved 11 = reserved 11 = reserved - For DXC DE1-HDSL, DT1-HDSL, D16GSDSL, D8SL External ports - 2 Octets MSB octet: far-end modem channel interface LSB octet: Sub Link existence (Y/N), far-end modem type, synchronization with far-end modem MSB octet: 0000 0000 = no interface 0000 0001 = db15 (X21) 0000 0010 = IR-IP 0000 0011 = IR-ETH-Q 0000 0100 = V35 0000 0101 = ETH-RJ45 0000 0110 = G703 0000 0111 = db25 (RS530) 0000 1000 = ETH-BNC 0000 1001 = E1(Balanced) 0000 1010 = E1(Unbalanced) 0000 1011 = IR-ETH-QN Rest of the combinations: reserved LSB octet: Bit 7 6 5 4 3 2 1 0 LSB | |___________| |__| SL modem sync or Box material SL: modem: 00000 = other sync: 00 = not sync 0=not exist 00001 = unknown 01 = sync 1=exists 00010 = ASMi-31/2 10 = reserved 00011 = HCD-E1 11 = reserved Box material 00100 = HTU-E1 (for D8SL card): 00101 = HTU-2 0=metal 00110 = ASMi-52 SA/2W/Slave 1=plastic 00111 = ASMi-52 SA/2W/Master 01000 = ASMi-52/CQ card of LRS-24 01001 = ASMi-52/CD card of LRS-24 01010 = D16GSDSL card of DXC-3000 01011 = LRS-52 01100 = FCD 01110 = D8GSDSL card of DXC-3000 01111 = ASMi-52A Rest = reserved
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

prtGenRdnStatus		1.3.6.1.4.1.164.3.3.3.1.1.1.16
This object indicates if this port is part of a redundant pair and in this case, if it is On or Off. none(1) - No redundancy or Not Applicable off (2) - the port is part of a redundant pair and it is Off from Redundancy point of view (not the port used). on (3) - the port is part of a redundant pair and it is On from Redundancy point of view (it is the port used).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), off(2), on(3)

prtGenTestMaskXP		1.3.6.1.4.1.164.3.3.3.1.1.1.17
This is an Expanded test mask of the prtGenTestMask object. The prtGenTestMask object reached its maximum, being an Integer with 31 bits. This object indicates which tests from the 'prtGenTestCmdXP' list are allowed for the selected port. If a specific test is allowed, its respective bit will be SET in the mask : TEST BIT ----------- --- localLoop 1 =LSB remoteLoop 2 bert 3 plb 4 inband 5 prbs 8 loop2-v54 (RLB) 9 loop3-v54 (LLB) 10 Tone injection 13 Tx-plb 14 Tx-llb 15 DTE loop (HSSI) 16 HDSL-Tx-Inband 20 HDSL-Rx-Inband 21 Monitor 22 (test port) User Line Loopback 23 Rem-Loop-on-Rem-Unit 25 LBBD 26 LB1 27 LB2 28 BERT-on-Rem-Unit 29 TS Remote Loop 30 LLB-on-Rem-Unit 31 Downstream-AIS 32 Upstream-AIS 33 Send-RDI 34 Test Per TS 35 e.g : If the return value is 00000003 hex -> Bits 1 & 2 are set -> the allowed tests are : local-loop remote-loop
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

prtGenTestCmdXP		1.3.6.1.4.1.164.3.3.3.1.1.1.18
This is an Expanded test command of the prtGenTestCmd object. The prtGenTestCmd object reached its maximum, being an Integer with 31 bits. Setting this object to a value as detailed furter on (except 0) will initiate a test on the specific port, if the operation is allowed (according to TestMaskXP). If the operation is not allowed, the mux will ignore the operation. The test/s requested will be set according to the respective bit: TEST BIT ----------- --- localLoop 1 =LSB remoteLoop 2 bert 3 plb 4 inband 5 prbs 8 loop2-v54 (RLB) 9 loop3-v54 (LLB) 10 Tone injection 13 Tx-plb 14 Tx-llb 15 DTE loop (HSSI) 16 HDSL-Tx-Inband 20 HDSL-Rx-Inband 21 Monitor 22 (test port) User Line Loopback 23 Rem-Loop-on-Rem-Unit 25 LBBD 26 LB1 27 LB2 28 BERT-on-Rem-Unit 29 TS Remote Loop 30 LLB-on-Rem-Unit 31 Downstream-AIS 32 Upstream-AIS 33 Send-RDI 34 Test Per TS 35 e.g : If the requested value is 00000003 hex -> Bits 1 & 2 are set -> the requested tests are : local-loop remote-loop Setting this object to stop (value=0 ; all bits are 0), will stop all the user requested tests running on the selected port; it will NOT stop the tests initiated by the system.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

prtGenTestRunningXP		1.3.6.1.4.1.164.3.3.3.1.1.1.19
This is an Expanded object of the prtGenTestRunning object. The prtGenTestRunning object reached its maximum, being an Integer with 31 bits. This object indicates which tests are running currently on the selected port (initiated by user and/or by the system). If a specific test is currently running on the port, its respective bit will be SET: TEST BIT ----------- --- localLoop 1 =LSB remoteLoop 2 bert 3 plb 4 llb 5 txInband 6 rxInband 7 prbs 8 loop2-v54 (RLB) 9 loop3-v54 (LLB) 10 DDS DSU loop 11 DDS CSU loop 12 Tone injection 13 Tx-plb 14 Tx-llb 15 DTE loop (HSSI) 16 Local DTE loop (HSSI)17 Local Line loop (HSSI)18 Remote Line loop (HSSI)19 HDSL-Tx-Inband 20 HDSL-Rx-Inband 21 Monitor 22 (test port) User Line Loopback 23 Network Line Loopback 24 Rem-Loop-on-Rem-Unit 25 LBBD 26 LB1 27 LB2 28 BERT-on-Rem-Unit 29 TS Remote Loop 30 LLB-on-Rem-Unit 31 Downstream-AIS 32 Upstream-AIS 33 Send-RDI 34 Test Per TS 35 e.g : If the return value is 00000003 hex -> Bits 1 & 2 are set -> the running tests are : local-loop remote-loop llb (Bit 5) - can be initiated by system only!
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

prtGenTestDurationTable		1.3.6.1.4.1.164.3.3.3.1.2
A table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtGenTestDurationEntry

prtGenTestDurationEntry		1.3.6.1.4.1.164.3.3.3.1.2.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtGenTestDurationEntry

prtGenTestPrtIdx		1.3.6.1.4.1.164.3.3.3.1.2.1.1
This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside/external, inside/internal. In the Kilomux, the port index is calculated as follows: 100*Slot+Ch. The external Ch numbers are 1..10, and the internal Ch numbers are 11..20. In the DXC : - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: * For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 .
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtGenTestIdx		1.3.6.1.4.1.164.3.3.3.1.2.1.2
This attribute indicates the test, the duration refers.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	localLoop(1), remoteLoop(2), bert(3), plb(4), rlb(5), llb(6), toneInjection(7), txInband(8), rxInband(9), remLoopOnRemUnit(10), bertOnRemUnit(11), llbOnRemUnit(12), txPlb(14), txLlb(15), dteLoop(16), hdslTxInband(20), hdslRxInband(21), monitor(22), userLineLoopback(23), lbbd(26), lb1(27), lb2(28), tsRemoteLoop(30), downstreamAis(32), upstreamAis(33), sendRdi(34)

prtGenTestDuration		1.3.6.1.4.1.164.3.3.3.1.2.1.3
This attribute indicates the maximum duration of executing a test on the specific port. This entry applies to the specified test . The resolution will be a minute, and the maximum duration is limited to 30 minutes . A zero value specifies no time limitation. When the test isn't active the agent initiates this object to 2 min. when the duration is needed and to 0 if it's not required.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtGenTsTable		1.3.6.1.4.1.164.3.3.3.1.3
The write operation into the Table's Objects is valid only for the TmpCnfg entry (Scratch),exept some products which enable direct writing to the ActiveCnfg. This is written in the respective product's spec.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtGenTsEntry

prtGenTsEntry		1.3.6.1.4.1.164.3.3.3.1.3.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtGenTsEntry

prtGenTsCnfgIdx		1.3.6.1.4.1.164.3.3.3.1.3.1.1
This attribute indicates the Idx of the Cnfg(1..255) being accessed. Idx of 255 relates to the TmpCnfg.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtGenTsPrtIdx		1.3.6.1.4.1.164.3.3.3.1.3.1.2
This attribute indicates a unique port number. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside, SP. In the DXC : - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: * For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 .
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtGenTsIdx		1.3.6.1.4.1.164.3.3.3.1.3.1.3
This attribute indicates a unique time slot position. The valid time slots are 1..25 for T1 Card (25=Fbit) 0..31 for E1 or HS Card . In G732S-E1 lines time slot 16 is not valid for data, it is dedicated for multiframe synchronization bits and voice signaling.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtGenTsType		1.3.6.1.4.1.164.3.3.3.1.3.1.4
The type of Timeslot. If the source or destination port is an HS port,'TS Type' must be 'data'. nc - means that this TimeSlot is not connected. voice, data, vcMP - also mean that this TS is connected. mng - means that this TS is dedicated to Management (not connected to another port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unknown(1), voice(2), data(3), vcMP(4), nc(5), mng(6)

prtGenTsIConPrt		1.3.6.1.4.1.164.3.3.3.1.3.1.5
This attribute indicates the internally (In Mux) connected port. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside, SP. * The outside ports will be the T1/E1 cards ports. The convention used will be (for DXC): - first two digits will be: (IO slot number+10) for a stand-alone unit, the IO slot will be considered 1. - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside ports will be for example, the HS cards ports. The convention used will be (for DXC): - first two digits will be: (IO slot number+10) for a stand-alone unit, the IO slot will be considered 1. - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . * noConnection - will be indicated as 10 for DXC and FCD-E1/T1. - will be indicated as 100 for FCD-E1/I and SMODs. * Split TS (same TS is Split to several ports) - 11. * notApplicable- will be indicated as 100 for LRS IMODs. All HS port's timeslots must have the same destination port.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtGenTsIConTs		1.3.6.1.4.1.164.3.3.3.1.3.1.6
This attribute indicates a unique time slot position. The valid time slots are 1..25 for T1 Card (25=Fbit) 0..31 for E1 (or HS) Card. In G732S-E1 lines time slot 16 is not valid for data, it is dedicated for multiframe synchronization bits and voice signaling. * For DXC: All HS port's timeslots must start with Timeslot no.1
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtAlr		1.3.6.1.4.1.164.3.3.3.1.4
OBJECT IDENTIFIER

prtSAlarmTable		1.3.6.1.4.1.164.3.3.3.1.4.1
A table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtSAlarmEntry

prtSAlarmEntry		1.3.6.1.4.1.164.3.3.3.1.4.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtSAlarmEntry

prtSAlarmIdx		1.3.6.1.4.1.164.3.3.3.1.4.1.1.1
A unique number to identify an entry in the alarm status table. Users should use the get next function to read this table because the indexes are not consecutive.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtSAlarmPrtIdx		1.3.6.1.4.1.164.3.3.3.1.4.1.1.2
This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside/external, inside/internal. In the Kilomux, the port index is calculated as follows: 100*Slot+Ch. The external Ch numbers are 1..10, and the internal Ch numbers are 11..20. In the DXC : - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: * For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 .
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtSAlarmCode		1.3.6.1.4.1.164.3.3.3.1.4.1.1.3
This object indicates a code related to a specific alarm description. The list of codes and their related descriptions will be sent to NMS request (for display purpose) by alrGenTable.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtSAlarmState		1.3.6.1.4.1.164.3.3.3.1.4.1.1.4
This object indicates the port alarm severity.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	event(3), minor(4), major(5), warning(6), critical(7)

prtSAlarmMask		1.3.6.1.4.1.164.3.3.3.1.4.1.1.5
Alarm Mask is : on/off.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), on(3)

prtSAlarmInvert		1.3.6.1.4.1.164.3.3.3.1.4.1.1.6
Alarm Invert is : on/off.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), on(3)

prtSAlarmOnOff		1.3.6.1.4.1.164.3.3.3.1.4.1.1.7
Alarm state is : on/off.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), on(3)

prtSAlarmCounter		1.3.6.1.4.1.164.3.3.3.1.4.1.1.8
A counter - how many times the alarm occured (ON) since last clear operation or since last Reset.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtAlrMaskTable		1.3.6.1.4.1.164.3.3.3.1.4.2
A table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtAlrMaskEntry

prtAlrMaskEntry		1.3.6.1.4.1.164.3.3.3.1.4.2.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtAlrMaskEntry

prtAlrMaskPrtIdx		1.3.6.1.4.1.164.3.3.3.1.4.2.1.1
This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside/external, inside/internal. In the Kilomux, the port index is calculated as follows: 100*Slot+Ch. The external Ch numbers are 1..10, and the internal Ch numbers are 11..20. In the DXC : - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: * For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 .
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtAlrMask		1.3.6.1.4.1.164.3.3.3.1.4.2.1.2
This object is a mask that indicates which port level alarms are masked. The masked alarms (their bit is set to '1') are neither sent to the manager, nor taken into account for alarm status and LEDs. Bit no. = Alarm code The bits that do not belong to the port level will be 0. This object is applicable only when prtGenAlrMaskAll=off (otherwise all port alarms are masked). Example: When Alarms having the codes 31 and 40 are masked, the value of this object will be 10080000000 (hex).
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(8)

prtBertTable		1.3.6.1.4.1.164.3.3.3.1.5
This table includes the BERT parameters, counters and commands. The configurable parameters: - prtBertPattern - prtBertInjectRate - prtBertTs are not Set per configuration (same for all Configurations) but start being applied by the Agent only upon successful Update/Download operation. Therefore, Set will enter the values to the Temporary Configuration of the agent, while Get will get the values of the Active Configuration.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtBertEntry

prtBertEntry		1.3.6.1.4.1.164.3.3.3.1.5.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtBertEntry

prtBertPrtIdx		1.3.6.1.4.1.164.3.3.3.1.5.1.1
This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside/external, inside/internal. In the Kilomux, the port index is calculated as follows: 100*Slot+Ch. The external Ch numbers are 1..10, and the internal Ch numbers are 11..20. In the DXC : - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: * For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . In the MP : - first two digits will be: (IO slot number+10) - last one/two digits will be according to the external port number within the card: exPrt1 -> 1 exPrt2 -> 3 exPrt3 -> 5 exPrt4 -> 7 .
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtBertPattern		1.3.6.1.4.1.164.3.3.3.1.5.1.2
This object indicates the pattern of the BERT. p2Exxm1 = 2Exx-1. pxx = pattern xx. This object is the same for all configurations. notApplicable - when this object is not supported.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	p2E3m1(1), p2E4m1(2), p2E5m1(3), p2E6m1(4), p2E7m1(5), p511(6), p2E10m1(7), p2047(8), p2E15m1(9), p2E17m1(10), p2E18m1(11), p2E20m1(12), qrss(13), p2E21m1(14), p2E22m1(15), p2E23m1(16), p2E25m1(17), p2E28m1(18), p2E29m1(19), p2E31m1(20), p2E32m1(21), rj011(22), p63(23), p1M7S(24), p1S7M(25), alternate(26), mark(27), space(28), p2E11m1(29), notApplicable(255)

prtBertInjectRate		1.3.6.1.4.1.164.3.3.3.1.5.1.3
This object indicates the error rate injection of the BERT. r10Emx = 10E-x This object is the same for all configurations. single - single error injection. notApplicable - when this object is not supported.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noError(1), r10Em1(2), r10Em2(3), r10Em3(4), r10Em4(5), r10Em5(6), r10Em6(7), r10Em7(8), single(9), notApplicable(255)

prtBertInjectErrRateCmd		1.3.6.1.4.1.164.3.3.3.1.5.1.4
This object controls activation/deactivation of the Error Rate Injection during BERT.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

prtBertInjectSingleErrCmd		1.3.6.1.4.1.164.3.3.3.1.5.1.5
This object enables to initiate a Single Error Injection during BERT (on). Upon completion, the value will automatically change to off(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

prtBertRunTime		1.3.6.1.4.1.164.3.3.3.1.5.1.6
This object indicates how much time (seconds) passed since BERT started to run.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtBertESs		1.3.6.1.4.1.164.3.3.3.1.5.1.7
How many Errored Seconds were detected since BERT started to run. Counter for Kmux and MP.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtBertSyncLoss		1.3.6.1.4.1.164.3.3.3.1.5.1.8
How many times Sync Loss was detected since BERT started to run. For some products: number of seconds in which Sync Loss occured since BERT started to run. See product specification.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtBertErrorBits		1.3.6.1.4.1.164.3.3.3.1.5.1.9
How many Error Bits were detected since BERT started to run.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtBertClearCounters		1.3.6.1.4.1.164.3.3.3.1.5.1.10
Setting this object to ON, will enforce a clear operation of some BERT Counters. Upon completion, the value will automatically change to off(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

prtBertSyncStatus		1.3.6.1.4.1.164.3.3.3.1.5.1.11
Sync Status while BERT runs.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), syncLoss(2), sync(3)

prtBertTs		1.3.6.1.4.1.164.3.3.3.1.5.1.12
This object indicates on which TSs of the selected port, BERT should be applied. Each Bit of the Octet represents a TS: 31 ......0 MSB LSB Bit 0 will not be used. If the bit value is '1' - BERT should be applied on this TS. For a T1 port, the valid raised bits ('1') are: 1..25. For an E1 port, the valid raised bits ('1') are: 1..31. Agents that do not support this feature will send SIZE 0.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..4)

prtBertResult		1.3.6.1.4.1.164.3.3.3.1.5.1.13
This object indicates Result of BERT for the selected port (number of error bits divided to the total number of data bits.) Applicable only if BERT is running on this port Agents that do not support this feature will send SIZE 0.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

prtBertTxBits		1.3.6.1.4.1.164.3.3.3.1.5.1.14
How many data bits were transmitted since BERT started to run, or since last counter clear (prtBertClearCounters set to on).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtBertRxBits		1.3.6.1.4.1.164.3.3.3.1.5.1.15
How many data bits were Received since BERT started to run, or since last counter clear (prtBertClearCounters set to on).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtBertTxErrorBits		1.3.6.1.4.1.164.3.3.3.1.5.1.16
Number of injected error bits since BERT started to run, or since last counter clear (prtBertClearCounters set to on).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtMonTable		1.3.6.1.4.1.164.3.3.3.1.6
For DXC, the write operation into the Table's Objects is valid only for the TmpCnfg entry (Scratch).
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtMonEntry

prtMonEntry		1.3.6.1.4.1.164.3.3.3.1.6.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtMonEntry

prtMonCnfgIdx		1.3.6.1.4.1.164.3.3.3.1.6.1.1
This object indicates the Idx of the Cnfg(1..255) being accessed. Idx of 255 relates to the TmpCnfg. For products that do not support configurations, 1 will be always used.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtMonitoringIdx		1.3.6.1.4.1.164.3.3.3.1.6.1.2
This object indicates the Monitoring Port Index. For DXC: The valid port number depends on the IO slot no., the installed card type and the port type: external, internal. * The external ports will according to the convention (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The internal ports will be according to the convention (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . For Optimux-T3: 255 (Not Applicable) will be always used. The Monitoring port is always the Station Clock (not considered an interface).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtMonitoringEnable		1.3.6.1.4.1.164.3.3.3.1.6.1.3
This object indicates if the prtMonitoringIdx is configured as a monitoring port or not. disabled = the port is NOT configured to monitor. Setting this object to this value will cause reset (to 0) of the prtMonitoringTSs and prtMonitoredTSs objects. enabled = the port IS configured to monitor. For Optimux-T3: always enabled (RO supported).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), disabled(2), enabled(3)

prtMonitoringTSs		1.3.6.1.4.1.164.3.3.3.1.6.1.4
This object indicates which TSs of the Monitoring port, the test equipment should monitor. Each Bit of the Octet represents a TS: 31 ......0 MSB LSB Bit 0 will not be used. If the bit value is '1' - this TS should be monitored. For a T1 port, the valid raised bits ('1') are: 1..24. For an E1 port, the valid raised bits ('1') are: 1..31. Default: all bits='0' Agents that do not support this feature will send SIZE 0. This object can be Set as described only if prtMonitoringEnable=enabled.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..4)

prtMonitoredPort		1.3.6.1.4.1.164.3.3.3.1.6.1.5
This object indicates the MONITORED Port Index that the Monitoring port monitors. For DXC: The valid port number depends on the IO slot no., the installed card type and the port type: external, internal. * The external ports will according to the convention (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The internal ports will be according to the convention (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . * 100 - no port monitored For Optimux-T3: The valid channels are: 0 = no Ch monitored 1..21 or 1..28 (=CH1..CH21 or CH1..CH28) according to product's configuration.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtMonitoredTSs		1.3.6.1.4.1.164.3.3.3.1.6.1.6
This object indicates which TSs of the Monitored port, should be monitored. Each Bit of the Octet represents a TS: 31 ......0 MSB LSB Bit 0 will not be used. If the bit value is '1' - this TS should be monitored. For a T1 port, the valid raised bits ('1') are: 1..24. For an E1 port, the valid raised bits ('1') are: 1..31. Default: all bits='0' Agents that do not support this feature will send SIZE 0. This object can be Set as described only if prtMonitoringEnable=enabled.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..4)

prtCfgParam		1.3.6.1.4.1.164.3.3.3.1.7
OBJECT IDENTIFIER

prtCfgParamTable		1.3.6.1.4.1.164.3.3.3.1.7.1
The write operation into the Table Objects is valid only to the TmpCnfg entry. KMUX parameters are for the cards: KMBE/New, KVF.6 family.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtCfgParamEntry

prtCfgParamEntry		1.3.6.1.4.1.164.3.3.3.1.7.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtCfgParamEntry

prtCfgParamCnfgIdx		1.3.6.1.4.1.164.3.3.3.1.7.1.1.1
This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtCfgParamIdx		1.3.6.1.4.1.164.3.3.3.1.7.1.1.2
A unique identifier of the port (within the card when applicable). - For KM-2100: Slot*100+Ch external ports: Ch=1..10 internal ports (sub-channels): Ch=11..20. - For FCD-T1/E1(L): MAIN=111, SUB=113, CH1=122, CH2=124. - For other devices, see specific device's spec.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtCfgParamSlt		1.3.6.1.4.1.164.3.3.3.1.7.1.1.3
This attribute indicates a unique number to identify the slot where the card is inserted in. In the 2104 Unit the entries kmxIO5(111)..kmxIO12(118) are not valid. notApplicable(255) - for products that do not have Slots.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), kmxIO1(107), kmxIO2(108), kmxIO3(109), kmxIO4(110), kmxIO5(111), kmxIO6(112), kmxIO7(113), kmxIO8(114), kmxIO9(115), kmxIO10(116), kmxIO11(117), kmxIO12(118), notApplicable(255)

prtCfgParamOperatedMl		1.3.6.1.4.1.164.3.3.3.1.7.1.1.4
The main link for this channel. The field is relevant only for ML modes of Dual, Priority Bumping and Switched Backup.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), kmxMlA(103), kmxMlB(104)

prtCfgParamMlAtoMlBPrio		1.3.6.1.4.1.164.3.3.3.1.7.1.1.5
ML-A to ML-B Priority. The field is relevant only for ML modes of Priority Bumping and Switched Backup.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), low(2), high(3)

prtCfgParamMlBtoMlAPrio		1.3.6.1.4.1.164.3.3.3.1.7.1.1.6
ML-B to ML-A Priority. The field is relevant only for ML modes of Priority Bumping.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), low(2), high(3)

prtCfgParamInbandLoopDetection		1.3.6.1.4.1.164.3.3.3.1.7.1.1.7
Inband Loop Detection. The field is relevant for FCD-T1/E1(L) ports.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), disabled(2), enabled(3)

prtCfgParamInbandLoopPatternCfg		1.3.6.1.4.1.164.3.3.3.1.7.1.1.8
This object indicates if Inband Loop polynomial pattern will be according to RDL Loop (the standard) or User Configurated according to prtCfgParamInbandLoopActPattern and prtCfgParamInbandLoopDeactPattern.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), rdlLoop(2), userConfig(3)

prtCfgParamInbandLoopActPattern		1.3.6.1.4.1.164.3.3.3.1.7.1.1.9
This object is a binary string of up to 8 bits. Though the syntax allows for any ASCII characters, for this object only '0' or '1' characters are valid. The string determines coefficients of the polynomial pattern sent to the port in order to Activate the Inband Loop. This object is relevant only when prtCfgParamInbandLoopPatternCfg=userConfig.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

prtCfgParamInbandLoopDeactPattern		1.3.6.1.4.1.164.3.3.3.1.7.1.1.10
This object is a binary string of up to 8 bits. Though the syntax allows for any ASCII characters, for this object only '0' or '1' characters are valid. The string determines coefficients of the polynomial pattern sent to the port in order to Deactivate the Inband Loop. This object is relevant only when prtCfgParamInbandLoopPatternCfg=userConfig.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

prtT1E1StatTable		1.3.6.1.4.1.164.3.3.3.2.1
T1/E1 port statistics table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtT1E1StatEntry

prtT1E1StatEntry		1.3.6.1.4.1.164.3.3.3.2.1.1
An entry in the T1/E1 port statistics table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtT1E1StatEntry

prtT1E1SPrtIdx		1.3.6.1.4.1.164.3.3.3.2.1.1.1
This attribute indicates a unique port number. The same numbering as for prtGenPrtIdx. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside. * The outside ports will be the T1/E1 cards ports. The convention used will be (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 .
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtT1E1SSlt		1.3.6.1.4.1.164.3.3.3.2.1.1.2
This attribute indicates a unique number to identify the slot where the card is inserted in. When the unit is stand-alone, this object is not applicable and 255 will be used.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), standAlone(255)

prtT1E1OosCount		1.3.6.1.4.1.164.3.3.3.2.1.1.3
This object is applicable only for an E1 active port. It provides the number of red alarm events since the last count clearing.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtT1E1BpvLastMin		1.3.6.1.4.1.164.3.3.3.2.1.1.4
This object is applicable only for an E1 active port. It provides the number of BPV (BiPolar Violation) events detected during the last minute.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtT1E1BpvMax		1.3.6.1.4.1.164.3.3.3.2.1.1.5
This object is applicable only for an E1 active port. It provides the maximal number of BPV (BiPolar Violation) events (per minute), detected during the worst minute.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

prtT1E1CnfgTable		1.3.6.1.4.1.164.3.3.3.2.2
T1/E1 port configuration table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtT1E1CnfgEntry

prtT1E1CnfgEntry		1.3.6.1.4.1.164.3.3.3.2.2.1
An entry in the T1/E1 port configuration table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtT1E1CnfgEntry

prtT1E1CnfgIdx		1.3.6.1.4.1.164.3.3.3.2.2.1.1
This attribute indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtT1E1PrtIdx		1.3.6.1.4.1.164.3.3.3.2.2.1.2
This attribute indicates a unique port number. The same numbering as for prtGenPrtIdx. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside. In the DXC : - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: * For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . In the Kilomux, the port index is calculated as follows: 100*Slot+Ch. The external Ch numbers are 1..10, and the internal Ch numbers are 11..20.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtT1E1Slt		1.3.6.1.4.1.164.3.3.3.2.2.1.3
This attribute indicates a unique number to identify the slot where the card is inserted in. When the unit is stand-alone, this object is not applicable and 255 will be used.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), kmxMlA(103), kmxMlB(104), kmxOpt(106), kmxIO1(107), kmxIO2(108), kmxIO3(109), kmxIO4(110), kmxIO5(111), kmxIO6(112), kmxIO7(113), kmxIO8(114), kmxIO9(115), kmxIO10(116), kmxIO11(117), kmxIO12(118), standAlone(255)

prtT1E1LineType		1.3.6.1.4.1.164.3.3.3.2.2.1.4
This variable indicates the variety of T1/E1 Line implementing this circuit. The type of circuit affects the number of bits per second that the circuit can reasonably carry, as well as the interpretation of the usage and error statistics. The values, in sequence, describe: TITLE: SPECIFICATION: esf Extended SuperFrame DS1 d4 AT&T D4 format DS1 - SF e1 CCITT Recommendation G.704 (Table 4a) - G732N e1Crc CCITT Recommendation G.704 (Table 4b) - G732N with CRC e1MF G.704 (Table 4a) with TS16 multiframing enabled - G732S e1CrcMF G.704 (Table 4b) with TS16 multiframing enabled - G732S with CRC unframed T1 - applicable values: (1),(2),(3),(8) E1 - applicable values: (1),(4),(5),(6),(7),(8)
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), esf(2), d4(3), e1(4), e1Crc(5), e1MF(6), e1CrcMF(7), unframed(8)

prtT1E1LineCode		1.3.6.1.4.1.164.3.3.3.2.2.1.5
This variable describes the variety of Zero Code Suppression used on the link, which in turn affects a number of its characteristics. jbzs=b7zs refers the Jammed Bit Zero Suppres- sion, in which the AT&T specification of at least one pulse every 8 bit periods is literal- ly implemented by forcing a pulse in bit 8 of each channel. Thus, only seven bits per chan- nel, or 1.344 Mbps, is available for data (used for T1). b8zs refers to the use of a specified pattern of normal bits and bipolar violations which are used to replace a sequence of eight zero bits (used for T1). ANSI Clear Channels may use zbtsi, or Zero Byte Time Slot Interchange. E1 links, with or without CRC, use hdb3 or ami (= TRAN). amI (=TRAN) refers to a mode wherein no zero code suppression is present and the line encoding does not solve the problem directly. In this application, the higher layer must provide data which meets or exceeds the pulse density re- quirements, such as inverting HDLC data.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	jbzs(1), b8zs(2), hdb3(3), zbtsi(4), ami(5), other(6)

prtT1E1SignalMode		1.3.6.1.4.1.164.3.3.3.2.2.1.6
'none' indicates that no bits are reserved for signaling on this channel. 'robbedBit' indicates that T1 Robbed Bit Signaling is in use. 'bitOriented' indicates that E1 Channel Associated Signaling (CAS) is in use. 'messageOriented' indicates that Common Channel Signaling (CCS) is in use either on channel 16 of an E1 link or channel 24 of a T1.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), robbedBit(2), bitOriented(3), messageOriented(4)

prtT1E1Fdl		1.3.6.1.4.1.164.3.3.3.2.2.1.7
This bitmap describes the use of the facili- ties data link, and is the sum of the capabili- ties: 'other' indicates that a protocol other than one following is used. 'ansi-T1-403' refers to the FDL exchange recommended by ANSI. 'att-54016' refers to ESF FDL exchanges. 'fdl-none' indicates that the device does not use the FDL. 'transFdl' indicates transition between two ports of the same card.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), ansi-T1-403(2), att-54016(4), fdl-none(8), transFdl(16)

prtT1E1FdlMode		1.3.6.1.4.1.164.3.3.3.2.2.1.8
Fdl Mode of the T1 selected port. notApplicable - will be used for an E1 port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), user(2), carrier(3), notApplicable(255)

prtT1E1Sync		1.3.6.1.4.1.164.3.3.3.2.2.1.9
This object enables returning to normal operation, after the end of a main/sub link red alarm event, in reduced time. 'tr62411' - complies with AT&T TR-62411 (after 10 seconds). Applicable for both T1 and E1 interfaces. 'ccitt' - complies with CCITT standard. Applicable only for E1 interfaces. 'fast' - after 1 second.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), tr62411(2), ccitt(3), fast(4)

prtT1E1CGA		1.3.6.1.4.1.164.3.3.3.2.2.1.10
This object selects the method used to signal the CGA state to the other end, through the main/sub link. 'none' - non-transparent mode. When one of the links (main/sub) will be in Out Of Service state, both 'Data/Voice Oos' and 'Oos Signal' will be transmitted to the other end. 'trans' - when one of the links (main/sub) will be in Out Of Service state, 'Data/Voice Oos' will be transmitted to the other end. 'full' - fully-transparent mode. When one of the links (main/sub) will be in Out Of Service state, neither 'Data/Voice Oos' nor 'Oos Signal' will be transmitted to the other end.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), trans(2), full(3)

prtT1E1IdleCode		1.3.6.1.4.1.164.3.3.3.2.2.1.11
This object selects the code transmitted to fill idle (unused) time slots in the main link frame. Valid range: (0 - FF HEX) .
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..4)

prtT1E1OosSignal		1.3.6.1.4.1.164.3.3.3.2.2.1.12
'idle' = '0' = on-hook, idle state 'busy' = '1' = off-hook, busy state 'forcedIdle' = SP = both A and B signaling bits are forced to '0' during out-of-service periods. 'forcedBusy' = MK = both A and B signaling bits are forced to '1' during out-of-service periods. 'busyIdle' = MK_SP = A and B bits are forced to '1' for 2.5 seconds; then they are switched to '0' until out-of-service condition disappears. 'idleBusy' = SP_MK = A and B bits are forced to '0' for 2.5 seconds; then they are switched to '1' until out-of-service condition disappears. - for T1: '0'=0 ; '1'=1 - for E1: '0'=1 ; '1'=0
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notsupported(2), forcedIdle(3), forcedBusy(4), busyIdle(5), idleBusy(6)

prtT1E1VoiceOos		1.3.6.1.4.1.164.3.3.3.2.2.1.13
Voice Out-Of-Service code. Valid range: (0 - FF HEX). For agents that do not support this feature, the value will always be 0.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..4)

prtT1E1DataOos		1.3.6.1.4.1.164.3.3.3.2.2.1.14
Data Out-Of-Service code. Valid range: (0 - FF HEX). For agents that do not support this feature, the value will always be 0.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..4)

prtT1E1LineLengthMask		1.3.6.1.4.1.164.3.3.3.2.2.1.15
This attribute is the line length mask parameter used only for T1/DSU interfaces. len400p533ft=length range: 400ft to 533ft 'fcc68' - provides compliance with the FCC 68.308 Option A output pulse mask.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unknown(1), len0p133ft(2), len134p266ft(3), len267p399ft(4), len400p533ft(5), len534p655ft(6), fcc68(7)

prtT1E1TxGainMask		1.3.6.1.4.1.164.3.3.3.2.2.1.16
This attribute is the tx gain mask parameter (dB), used only for T1/CSU interfaces.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), txGain0db(2), txGain7dot5db(3), txGain15db(4), txGain22dot5db(5)

prtT1E1InbandMng		1.3.6.1.4.1.164.3.3.3.2.2.1.17
A unique number to identify an Inband management over the link. internal - supported by KM-2100 only. It means that the management is internal to the frame. It takes part of the ML Frame bits (instead of data).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), fdlOrTs0(3), dedicatedTs(4), dedicatedPpp(5), dedicatedFr(6), internal(7)

prtT1E1InbandMngRate		1.3.6.1.4.1.164.3.3.3.2.2.1.18
A unique number to identify the rate of the Inband management. It is required only for E1 links and is applicable only when prtExT1E1InbandMng selected is FdlOrTs0 or dedicatedTs.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), r4k(2), r8k(3), r12k(4), r16k(5), r32k(6), r64k(7), r20k(8)

prtT1E1DedicatedTs		1.3.6.1.4.1.164.3.3.3.2.2.1.19
The value is differently determined for different products. There are two methods: 1) A unique number to identify Dedicated TS of the T1/E1 port. It is applicable only when prtExT1E1InbandMng selected is dedicatedTs. 1..24 - Dedicated TS of T1 1..31 - Dedicated TS of E1 255 - notApplicable (for agents that do not support this feature) Other values are invalid. 2) For FCD-STM, up to five TSs may be dedicated to management. This object value is the Sum (sigma) of 2**n, where n =TS-1 e.g. Time slots 3,5,7,9,11 are dedicated to management: 2** 2 +2** 4 +2** 6 +2** 8 +2**10 = 4+16+64+256+1024=1364 User should consult the product specification, to find out the method employed.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtT1E1InbandMngRoutProt		1.3.6.1.4.1.164.3.3.3.2.2.1.20
Inband Mng Routing Protocol of the port. When prtT1E1InbandMng is 'dedicatedPpp'-'proprietary' and 'rip2' are applicable. For other values - only 'proprietary' is applicable. For FCD-M and FCD-A: When prtT1E1InbandMng is 'dedicatedPpp' or 'dedicatedFr': 'None', 'proprietary' and 'rip2' are applicable. When prtT1E1InbandMng is 'fdlOrTS0' or 'dedicatedTs': 'None' and 'proprietary' are applicable. When prtT1E1InbandMng is 'off': 'None' is applicable.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), none(2), proprietary(3), rip2(4)

prtT1E1LinkMode		1.3.6.1.4.1.164.3.3.3.2.2.1.21
regular - TSs are connected by user via TS Assignment only transparent - when a port with this Link Mode is connected to an internal T1/E1 port of a T3/E3 card, TS0, TS16 and Fbit are transparently transferred to the E3/T3 stream.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), regular(2), transparent(3)

prtT1E1Multiplier		1.3.6.1.4.1.164.3.3.3.2.2.1.22
The data rate of each TS. The multiplier values can be 56 kbps or 64 kbps. For T1 only.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), br56(2), br64(3)

prtT1E1RxGain		1.3.6.1.4.1.164.3.3.3.2.2.1.23
This attribute is the rx volume (dB).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), rxGain12dB(2), rxGain30dB(3), rxGain36dB(4), shortHaul(5), longHaul(6), rxGain20dB(7)

prtT1E1RAI		1.3.6.1.4.1.164.3.3.3.2.2.1.24
Remote Alarm Signal
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), off(2), on(3)

prtT1E1LineMode		1.3.6.1.4.1.164.3.3.3.2.2.1.25
Interface type of the port. For T1 - csu, dsu are the valid values For E1 - dsu, ltu are the valid values
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), csu(2), dsu(3), ltu(4)

prtT1E1TS0SaBits		1.3.6.1.4.1.164.3.3.3.2.2.1.26
This object is applicable only for E1 ports. For T1, string size will be 0. For E1, it enables user to select the use of TS0 Sa Bits 4..8, by 3 octets: The order (in hexa display): free Sa-Bit-4 Sa-Bit-5 Sa-Bit-6 Sa-Bit-7 Sa-Bit-8 |___________| |________________| |________________| MSByte LSByte Each Sa Bit will be represented by a nibble, having the following meaning: 0000 = zero 0001 = one 0010 = management 0011 = transparent the rest are reserved for future use.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

prtT1E1ConnectedTS		1.3.6.1.4.1.164.3.3.3.2.2.1.27
This parameter indicates if there is any connected TS for this interface.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), no(2), yes(3)

prtT1E1Ts0SaBit		1.3.6.1.4.1.164.3.3.3.2.2.1.28
This parameter indicates whether to send TS 0, or not. noMng= TS 0 is looped, therefore not sent. mng= TS 0 isn't looped, therefore it is sent.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), noMng(2), mng(3)

prtT1E1SameFeCnfg		1.3.6.1.4.1.164.3.3.3.2.2.1.29
This parameter indicates whether the same E1 configuration parameters and TS assignment are set both to the local and remote device. Read-Write access is applicable only in G732N framed mode. For G732S and UNFRAMED this parameter is set by agent to YES and is Read Only. In Case of conflict during power-up between the central and remote, the value set by the central unit is the valid one.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), no(2), yes(3)

prtT1E1RemCrc4		1.3.6.1.4.1.164.3.3.3.2.2.1.30
This object indicates whether the E1 of the Remote device connected to this E1 port, will have CRC-4 or not.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), no(2), yes(3)

prtT1E1MaxTSs		1.3.6.1.4.1.164.3.3.3.2.2.1.31
This object is applicable only for DXC D4T1, D4E1, D8T1, D8E1 external ports and D8GSL internal E1 ports. It is relevant only when sysCIntTsAllocMode=static(2). 255=not applicable If prtT1E1LineType=unframed(8), the value of this object must be 32. Else, the valid values are 0..31.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtT1E1EocTsConfig		1.3.6.1.4.1.164.3.3.3.2.2.1.32
This object indicates whether the use of EOC for TS Configuration is enabled or not.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), disabled(2), enabled(3)

prtT1E1Role		1.3.6.1.4.1.164.3.3.3.2.2.1.33
This object indicates whether this port behaves as SUB or Main link.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), sub(2), main(3)

prtT1E1PppEchoFailDetection		1.3.6.1.4.1.164.3.3.3.2.2.1.34
This object indicates whether the PPP Echo is taken into account for its Fail Detection. This object is relevant when Inband Mng between devices is Dedicated TS PPP. Default=Disable. Enable - will be selected mainly when a T1/E1 Ring exists and between 2 adjacent Ring devices there is another device or Net, that causes these Ring devices not to sense that the PPP connection between them is lost. In this case, Echo Request should be initiated by the port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), enable(3)

prtT1E1FdlMsgTable		1.3.6.1.4.1.164.3.3.3.2.3
This table is applicable for a T1 interface with 'esf' LineType or E1 interface, when CRC is enabled (LineType).
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtT1E1FdlMsgEntry

prtT1E1FdlMsgEntry		1.3.6.1.4.1.164.3.3.3.2.3.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtT1E1FdlMsgEntry

prtT1E1FdlMsgPrtIdx		1.3.6.1.4.1.164.3.3.3.2.3.1.1
This attribute indicates a unique port number. The same numbering as for prtGenPrtIdx. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside. * The outside ports will be the T1/E1 cards ports. The convention used will be (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 .
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtT1E1FdlMsgFdlType		1.3.6.1.4.1.164.3.3.3.2.3.1.2
The Fdl type reference of the Fdl message.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	send(1), receive(2)

prtT1E1FdlMsgSlt		1.3.6.1.4.1.164.3.3.3.2.3.1.3
This attribute indicates a unique number to identify the slot where the card is inserted in. When the unit is stand-alone, this object is not applicable and 255 will be used.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), standAlone(255)

prtT1E1FdlMsg		1.3.6.1.4.1.164.3.3.3.2.3.1.4
FDL message.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

prtHSParamTable		1.3.6.1.4.1.164.3.3.3.3.1
A table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtHSParamEntry

prtHSParamEntry		1.3.6.1.4.1.164.3.3.3.3.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtHSParamEntry

prtHSCnfgIdx		1.3.6.1.4.1.164.3.3.3.3.1.1.1
This attribute indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtHSPrtIdx		1.3.6.1.4.1.164.3.3.3.3.1.1.2
This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside, SP. * The inside ports will be the HS cards ports. The convention used will be (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 .
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtHSSlt		1.3.6.1.4.1.164.3.3.3.3.1.1.3
This attribute indicates a unique number to identify the slot where the card is inserted in. When the unit is stand-alone, this object is not applicable and 255 will be used.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), standAlone(255)

prtHSRate		1.3.6.1.4.1.164.3.3.3.3.1.1.4
This object indicates the port rate (speed). auto - rate is selected automatically by system.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	r0x56eq0Kbps(1), r1x56eq56Kbps(2), r2x56eq112Kbps(3), r3x56eq168Kbps(4), r4x56eq224Kbps(5), r5x56eq280Kbps(6), r6x56eq336Kbps(7), r7x56eq392Kbps(8), r8x56eq448Kbps(9), r9x56eq504Kbps(10), r10x56eq560Kbps(11), r11x56eq616Kbps(12), r12x56eq672Kbps(13), r13x56eq728Kbps(14), r14x56eq784Kbps(15), r15x56eq840Kbps(16), r16x56eq896Kbps(17), r17x56eq952Kbps(18), r18x56eq1008Kbps(19), r19x56eq1064Kbps(20), r20x56eq1120Kbps(21), r21x56eq1176Kbps(22), r22x56eq1232Kbps(23), r23x56eq1288Kbps(24), r24x56eq1344Kbps(25), r25x56eq1400Kbps(26), r26x56eq1456Kbps(27), r27x56eq1512Kbps(28), r28x56eq1568Kbps(29), r29x56eq1624Kbps(30), r30x56eq1680Kbps(31), r31x56eq1736Kbps(32), r0x64eq0Kbps(33), r1x64eq64Kbps(34), r2x64eq128Kbps(35), r3x64eq192Kbps(36), r4x64eq256Kbps(37), r5x64eq320Kbps(38), r6x64eq384Kbps(39), r7x64eq448Kbps(40), r8x64eq512Kbps(41), r9x64eq576Kbps(42), r10x64eq640Kbps(43), r11x64eq704Kbps(44), r12x64eq768Kbps(45), r13x64eq832Kbps(46), r14x64eq896Kbps(47), r15x64eq960Kbps(48), r16x64eq1024Kbps(49), r17x64eq1088Kbps(50), r18x64eq1152Kbps(51), r19x64eq1216Kbps(52), r20x64eq1280Kbps(53), r21x64eq1344Kbps(54), r22x64eq1408Kbps(55), r23x64eq1472Kbps(56), r24x64eq1536Kbps(57), r25x64eq1600Kbps(58), r26x64eq1664Kbps(59), r27x64eq1728Kbps(60), r28x64eq1792Kbps(61), r29x64eq1856Kbps(62), r30x64eq1920Kbps(63), r31x64eq1984Kbps(64), r32x64eq2048Kbps(65), r32x56eq1792Kbps(66), r64x64eq4096Kbps(67), auto(200)

prtHSFifoSize		1.3.6.1.4.1.164.3.3.3.3.1.1.5
This object selects the size of the user data channel buffer FIFO used in the DTE2 mode. In the other modes, buffer size is automatically set by the DACS agent. Buffer FIFO size in bits, corresponds to FIFO lengths of +/-16, +/-30, +/-52, +/-72 bits.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	auto(1), b32bit(2), b60bit(3), b104bit(4), b144bit(5), notApplicable(255)

prtHSClkMode		1.3.6.1.4.1.164.3.3.3.3.1.1.6
Clock Mode of the user data channel. dce - DACS operates as a DCE and provides transmit and receive clocks to the synchronous user DTE. dte1- DACS supplies the receive clock to the user equipment and accepts the user transmit clock. dte2- DACS requires transmit and receive clocks from the user equipment.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	dce(1), dte1(2), dte2(3), notApplicable(255)

prtHSCTS		1.3.6.1.4.1.164.3.3.3.3.1.1.7
Selection of CTS line state in the user data channel. on - CTS continuously ON. rts - CTS line follows the RTS line.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	on(1), rts(2), notApplicable(255)

prtHSRtsState		1.3.6.1.4.1.164.3.3.3.3.1.1.8
RTS state of the port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(2), on(3), notApplicable(255)

prtHSInbandLoopback		1.3.6.1.4.1.164.3.3.3.3.1.1.9
This object indicates if Inband Loopback from the Network should be enabled or disabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), disabled(2), enabled(3)

prtHSInbandLoopPatternCfg		1.3.6.1.4.1.164.3.3.3.3.1.1.10
This object indicates if Inband Loop polynomial pattern will be according to RDL Loop (the standard) or User Configurated according to prtHSActivatePolyPattern and prtHSDeactivatePolyPattern.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), rdlLoop(2), userConfig(3)

prtHSInbandLoopActPattern		1.3.6.1.4.1.164.3.3.3.3.1.1.11
This object is a binary string of up to 8 bits. Though the syntax allows for any ASCII characters, for this object only '0' or '1' characters are valid. The string determines coefficients of the polynomial pattern sent to the port in order to Activate the Inband Loop. This object is relevant only when prtHSInbandLoopPatternCfg=userConfig.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

prtHSInbandLoopDeactPattern		1.3.6.1.4.1.164.3.3.3.3.1.1.12
This object is a binary string of up to 8 bits. Though the syntax allows for any ASCII characters, for this object only '0' or '1' characters are valid. The string determines coefficients of the polynomial pattern sent to the port in order to Deactivate the Inband Loop. This object is relevant only when prtHSInbandLoopPatternCfg=userConfig.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

prtHSDCD		1.3.6.1.4.1.164.3.3.3.3.1.1.13
Selection of DCD line state in the user data channel. linkOK - DCD line is ON only when active link is OK. on - DCD continuously ON.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), linkOK(2), on(3)

prtHSClkPolarity		1.3.6.1.4.1.164.3.3.3.3.1.1.14
This object indicates the clock polarity.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), normal(2), invert(3)

prtHSInterfaceType		1.3.6.1.4.1.164.3.3.3.3.1.1.15
This object indicates the selected electrical interface type.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), rs530(2), v35(3), rs422(4), x21(5), v24(6), rs530a(7), rs232(8), rs449(9)

prtHSUnframed		1.3.6.1.4.1.164.3.3.3.3.1.1.16
Unframed line for HS ports. yes - means that all TSs must be transferred, including TS0. In this case, prtHSRate must be r31x56eq1736Kbps OR r31x64eq1984Kbps.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), no(2), yes(3)

prtHSBertTable		1.3.6.1.4.1.164.3.3.3.3.2
A table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtHSBertEntry

prtHSBertEntry		1.3.6.1.4.1.164.3.3.3.3.2.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtHSBertEntry

prtHSBertPrtIdx		1.3.6.1.4.1.164.3.3.3.3.2.1.1
This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside, SP. * The inside ports will be the HS cards ports. The convention used will be (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 .
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtHSBertSlt		1.3.6.1.4.1.164.3.3.3.3.2.1.2
This attribute indicates a unique number to identify the slot where the card is inserted in. When the unit is stand-alone, this object is not applicable and 255 will be used.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), standAlone(255)

prtHSBertCountClr		1.3.6.1.4.1.164.3.3.3.3.2.1.3
Setting this object (to on) initiate bert counter clear operation. Valid only when bert test is active on the specific port. (Every time a new bert test starts, the counter is automatically cleared; this command enables clearing the counter while the test is running).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

prtHSBertTestResult		1.3.6.1.4.1.164.3.3.3.3.2.1.4
This object indicates the number of Bit Error Rate indicated during the BERT test. Active only when bert test is running on the selected port.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtSpCnfgTable		1.3.6.1.4.1.164.3.3.3.4.1
A table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtSpCnfgEntry

prtSpCnfgEntry		1.3.6.1.4.1.164.3.3.3.4.1.1
All the entries at this table are identical(have the same value) at all the configurations(1..255) except at the TmpCnfg. - For products supporting more than one configuration, the write operation into the Table Objects is valid only at the TmpCnfg entry. - For products that do not support configurations, the write operation into the Table Objects will be to prtSpCnfgIdx=1.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtSpCnfgEntry

prtSpCnfgIdx		1.3.6.1.4.1.164.3.3.3.4.1.1.1
This attribute indicates the Idx of the Cnfg(1..255) being accessed. Idx of 255 relates to the TmpCnfg.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtSpPrtIdx		1.3.6.1.4.1.164.3.3.3.4.1.1.2
This attribute indicates a unique port number of the SPor DP port. For DXC, it is the port in the active DCL card: - SP = 1 - NP ; DP = 2 For Kilomux, the port index is calculated as follows: 100*Slot+Ch. For FCD, PRBi, the SP port index=1. For Optimux-T3, the SP port index=71.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtSpUsage		1.3.6.1.4.1.164.3.3.3.4.1.1.3
This attribute indicates what is the usage of the port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unknown(1), noUse(2), nmsSlip(3), nmsPpp(4), muxSlip(5), muxPpp(6), terminal(7), dialOut(8)

prtSpRate		1.3.6.1.4.1.164.3.3.3.4.1.1.4
This attribute indicates the operation rate (speed) of the port. auto - automatic rate selection, by the agent.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	auto(1), s300bps(2), s1200bps(3), s2400bps(4), s4800bps(5), s9600bps(6), s19200bps(7), s38400bps(8), s57600bps(9), s115200bps(10)

prtSpDataBits		1.3.6.1.4.1.164.3.3.3.4.1.1.5
This attribute indicates the number of data bits in async frame
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	dataBits7(1), dataBits8(2)

prtSpParity		1.3.6.1.4.1.164.3.3.3.4.1.1.6
This attribute indicates the parity mode in async frame
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), odd(2), even(3)

prtSpCallOutMode		1.3.6.1.4.1.164.3.3.3.4.1.1.7
This attribute indicates the call-out mode. For DXC - this object is applicable only for the DP port (2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), none(2), all(3), major(4)

prtSpInterface		1.3.6.1.4.1.164.3.3.3.4.1.1.8
This attribute indicates the supervisory port interface. dce - the DACS appears as a DCE for the port. dte - the DACS operates as a DTE, for connection via modem, for the port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	dce(1), dte(2)

prtSpCTS		1.3.6.1.4.1.164.3.3.3.4.1.1.9
CTS line state. This object is applicable only for port (1) = SP
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), on(2), rts(3)

prtSpDcdDelay		1.3.6.1.4.1.164.3.3.3.4.1.1.10
DCD delay in msec. d10 = delay of 10msec. This object is applicable only for port (1) = SP
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), d0(2), d10(3), d50(4), d100(5), d200(6), d300(7)

prtSpDsr		1.3.6.1.4.1.164.3.3.3.4.1.1.11
DSR line state. This object is applicable only for port (1) = SP
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), on(2), dtr(3)

prtSpNoOfRetries		1.3.6.1.4.1.164.3.3.3.4.1.1.12
For DXC - this object is applicable only for port (2) = DP. The number of dialing retries requested. Default = 0
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..8

prtSpWaitForConnect		1.3.6.1.4.1.164.3.3.3.4.1.1.13
For DXC - this object is applicable only for port (2) = DP. Waiting time for connect, in seconds. Default = 30 sec.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), t30sec(2), t45sec(3), t60sec(4)

prtSpDialMode		1.3.6.1.4.1.164.3.3.3.4.1.1.14
For DXC - this object is applicable only for port (2) = DP. Dialing mode. Default=tone
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), tone(2), pulse(3)

prtSpAltNumMode		1.3.6.1.4.1.164.3.3.3.4.1.1.15
For DXC - this object is applicable only for port (2) = DP. It determines wether to use the alternate number or not. Default = no.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	no(2), yes(3)

prtSpPrimaryNum		1.3.6.1.4.1.164.3.3.3.4.1.1.16
For DXC - this object is applicable only for port (2) = DP. It is the Primary dialing number.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

prtSpAltNum		1.3.6.1.4.1.164.3.3.3.4.1.1.17
For DXC - this object is applicable only for port (2) = DP. It is the Alternate dialing number. This number is applicable only if prtSpAltNumMode is 'yes'.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

prtSpRoutProtocol		1.3.6.1.4.1.164.3.3.3.4.1.1.18
This attribute indicates the routing protocol of the port. notApplicable - for DP.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), none(2), proprietary(3), rip2(4)

prtSpCmd		1.3.6.1.4.1.164.3.3.3.4.1.1.19
SP Command. For LRS this parameter will be used for a Modem Command. Upon NMS's Get operation for devices that this parameter is notApplicable, agent will send NULL string.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(20)

prtSpActCallOut		1.3.6.1.4.1.164.3.3.3.4.1.1.20
This object indicates when to Activate Call-Out. It is used by FCD-T1/E1. always - to activate call-out always. linkFail - to activate call-out only when Link of Inband Management fails.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), always(2), linkFail(3)

prtSpAlrRelayMode		1.3.6.1.4.1.164.3.3.3.4.1.1.21
This attribute indicates the Alarm Relay Mode. notApplicable - for DP.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), normal(2), invert(3)

prtSpStopBits		1.3.6.1.4.1.164.3.3.3.4.1.1.22
This attribute indicates number of stop bits in an async frame.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), stopBits1(2), stopBits1dot5(3), stopBits2(4)

prtDimCnfgTable		1.3.6.1.4.1.164.3.3.3.5.1
A table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtDimCnfgEntry

prtDimCnfgEntry		1.3.6.1.4.1.164.3.3.3.5.1.1
The write operation into the Table Objects is valid only for the TmpCnfg entry (prtDimCnfgIdx=255).
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtDimCnfgEntry

prtDimCnfgIdx		1.3.6.1.4.1.164.3.3.3.5.1.1.1
This attribute indicates the Idx of the Cnfg(1..255) being accessed. Idx of 255 relates to the TmpCnfg.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtDimIdx		1.3.6.1.4.1.164.3.3.3.5.1.1.2
This attribute indicates a unique port number of the DIM card. The convention used for DXC: (IO slot number+10)*10 + 1 Example: port1 of IO slot 11 will be: 211 .
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtDimTxMode		1.3.6.1.4.1.164.3.3.3.5.1.1.3
Tx mode. regularTx - the links are connected to a similar outfit on the other side. In this mode, if a link fails, the transmitted bandwidth is decreased accordingly. broadcast - the links are connected to MORE than one similar outfit on the other side. In this mode, if a link fails, the transmitted bandwidth is not affected
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	regularTx(2), broadcast(3)

prtDimPolarity		1.3.6.1.4.1.164.3.3.3.5.1.1.4
Polarity.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	normalClk(2), inverted(3)

prtDimClkMode		1.3.6.1.4.1.164.3.3.3.5.1.1.5
Clock Mode. smooth - a clock that is not 'pulsed'(has no 'gaps'). In this mode the DXC does NOT receive back the clock signal. extSmooth - same as 'smooth' but in this mode, the DXC receives back the clock signal.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	extDce(2), dce(3), smooth(4), extSmooth(5)

prtDimMaxDelay		1.3.6.1.4.1.164.3.3.3.5.1.1.6
Max Delay permitted between the links, in msec.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	t16msec(2), t64msec(3)

prtDimMng		1.3.6.1.4.1.164.3.3.3.5.1.1.7
Use of DIM port for management. disabled - no management on DIM ts1 - 1 bit of TS1 is used for management.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(2), ts1(3), dedicatedFr(4)

prtDimMngRoutProt		1.3.6.1.4.1.164.3.3.3.5.1.1.8
Mng Routing Protocol of the port. none - when prtDimMng is 'disabled'.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), none(2), proprietary(3)

prtDimDestTable		1.3.6.1.4.1.164.3.3.3.5.2
A table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtDimDestEntry

prtDimDestEntry		1.3.6.1.4.1.164.3.3.3.5.2.1
The write operation is valid only for the TmpCnfg entry (prtDimDestCnfgIdx=255).
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtDimDestEntry

prtDestCnfgIdx		1.3.6.1.4.1.164.3.3.3.5.2.1.1
This attribute indicates the Idx of the Cnfg(1..255) being accessed. Idx of 255 relates to the TmpCnfg.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtDestDimIdx		1.3.6.1.4.1.164.3.3.3.5.2.1.2
This attribute indicates a unique port number of the DIM card. The convention used for DXC: (IO slot number+10) & 1 Example: port1 of IO slot 11 will be: 211 .
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtDestIdx		1.3.6.1.4.1.164.3.3.3.5.2.1.3
This attribute indicates a destination number of the DIM card.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..8

prtDest		1.3.6.1.4.1.164.3.3.3.5.2.1.4
Destination port,(of a T1/E1 port), that is connected to the DIM card, for the specified Destination number. 0 = No destination port. Else: For external ports: (IO Slot+10) & 1 for port 1 (IO Slot+10) & 3 for port 2 Example: port2 of IO slot 12 will be: 223 . For internal ports : (IO Slot+10) & 2 for port 1 (IO Slot+10) & 4 for port 2 (IO Slot+10) & 6 for port 3 (IO Slot+10) & 8 for port 4, etc...
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtDestConnect		1.3.6.1.4.1.164.3.3.3.5.2.1.5
Connection Status of the specified destination number. For a specified destination port, it depends both on the status of the port and on the status of the far-end port. Since this is a RO object, same value will be received for all configurations.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	no(2), yes(3)

prtICnfgTable		1.3.6.1.4.1.164.3.3.3.6.1
A table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtICnfgEntry

prtICnfgEntry		1.3.6.1.4.1.164.3.3.3.6.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtICnfgEntry

prtICnfgIdx		1.3.6.1.4.1.164.3.3.3.6.1.1.1
This attribute indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtIIdx		1.3.6.1.4.1.164.3.3.3.6.1.1.2
This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside, SP. * The ISDN B1, B2, D channels will be inside ports. For port index, see product specification.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtIRate		1.3.6.1.4.1.164.3.3.3.6.1.1.3
This object indicates the port rate in bits. Each TS contains 8 bits. Thus, 1 bit is equivalent to 8Kbps rate.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), nc(2), r2bit(3), r4bit(4), r8bit(5)

prtIConnect		1.3.6.1.4.1.164.3.3.3.6.1.1.4
D channel connection. no - disconnected yes - connected.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), no(2), yes(3)

prtHdslTable		1.3.6.1.4.1.164.3.3.3.7.1
HDSL port table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtHdslEntry

prtHdslEntry		1.3.6.1.4.1.164.3.3.3.7.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtHdslEntry

prtHdslIdx		1.3.6.1.4.1.164.3.3.3.7.1.1.1
This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside. * The HDSL ports will be external. For port index, see product specification.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtHdslMode		1.3.6.1.4.1.164.3.3.3.7.1.1.2
This object indicates the HDSL mode.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), central(2), remote(3)

prtHdslRptrType		1.3.6.1.4.1.164.3.3.3.7.1.1.3
The Repeater between Near and Far modem. none - no repeater exists between the modems hrpt - HRPT repeater exists between the modems.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), none(2), hrpt(3)

prtHdslMaxRate		1.3.6.1.4.1.164.3.3.3.7.1.1.4
Maximum Rate of the xDSL Line, in Kbps units. This object can be Set only for a Central unit.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), r192(2), r256(3), r320(4), r384(5), r448(6), r512(7), r576(8), r640(9), r768(10), r896(11), r1024(12), r1152(13), r1280(14), r1536(15), r1920(16), r2048(17)

prtHdslLinkType		1.3.6.1.4.1.164.3.3.3.7.1.1.5
The Link Type. msdsl2w - MSDSL 2 Wire hdsl2w - HDSL 2 Wire hdsl4w - HDSL 4 Wire gDsl - G.DSL
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), msdsl2w(2), hdsl2w(3), hdsl4w(4), gDsl(5)

prtHdslCompSwVer		1.3.6.1.4.1.164.3.3.3.7.1.1.6
This object indicates the Software Version of the component (Piggyback card) supporting this interface.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

prtHdslCompHwVer		1.3.6.1.4.1.164.3.3.3.7.1.1.7
This object indicates the Hardware Version of the component (Piggyback card) supporting this interface.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

prtT3E3CnfgTable		1.3.6.1.4.1.164.3.3.3.8.1
T3/E3 port configuration table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtT3E3CnfgEntry

prtT3E3CnfgEntry		1.3.6.1.4.1.164.3.3.3.8.1.1
An entry in the T3/E3 port configuration table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtT3E3CnfgEntry

prtT3E3CnfgIdx		1.3.6.1.4.1.164.3.3.3.8.1.1.1
This attribute indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config. For DXC, write operations can be performed only on the Temp Config. For products that do not support configurations, always 1 will be used.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

prtT3E3PrtIdx		1.3.6.1.4.1.164.3.3.3.8.1.1.2
This attribute indicates a unique port number. For DXC: The same numbering as for prtGenPrtIdx. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside. * The external ports convention used will be (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . For Optimux-T3: Link-A: 51 Link-B: 61 .
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prtT3E3Slt		1.3.6.1.4.1.164.3.3.3.8.1.1.3
This attribute indicates a unique number to identify the slot where the card is inserted in. When the unit is stand-alone, this object is not applicable and 255 will be used.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), standAlone(255)

prtT3E3LineLength		1.3.6.1.4.1.164.3.3.3.8.1.1.4
This object is the length of the ds3 line in feet. It provides information for line build out circuitry if it exists and can use this object to adjust the line build out. len0p450ft = 0 - 450 feet len451p900ft = 451 - 900 feet.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), len0p450ft(2), len451p900ft(3)

prtT3E3InbandMng		1.3.6.1.4.1.164.3.3.3.8.1.1.5
A unique number to identify the Frame Type over the link. For Optimux-T3: only values (4), (7) are supported.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), off(2), cBit(3), cBitTxRxMng(4), cBitTx(5), cBitTxMng(6), m13(7), cdpv(8), nationalBit(9)

prtT3E3AisFrame		1.3.6.1.4.1.164.3.3.3.8.1.1.6
This object is applicable only for Optimux-T3. It allows user to select whether the AIS sent will be framed or unframed.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), unframed(2), framed(3)

prtT3E3TxClockSource		1.3.6.1.4.1.164.3.3.3.8.1.1.7
Tx Clock Source.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	external(1), internal(2), notApplicable(255)

prtT3E3RoutProt		1.3.6.1.4.1.164.3.3.3.8.1.1.8
Routing Protocol of the port. This object is applicable only for T3 ports.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), none(2), proprietary(3), rip2(4)

prtT3E3AisTransmit		1.3.6.1.4.1.164.3.3.3.8.1.1.9
Indicates if AIS signal will be transmitted over the tributary E3/DS3 upon failure.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), enable(3)

cmprTable		1.3.6.1.4.1.164.3.3.4.1
A table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CmprEntry

cmprEntry		1.3.6.1.4.1.164.3.3.4.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	CmprEntry

cmprTypeIdx		1.3.6.1.4.1.164.3.3.4.1.1.1
This object indicates the Type of the Compressed data referred (which table, which level, etc). The type is a code according to a convention between agent and NMS.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cmprCnfgIdx		1.3.6.1.4.1.164.3.3.4.1.1.2
This object indicates the configuration number the Compressed information relates to.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cmprVersion		1.3.6.1.4.1.164.3.3.4.1.1.3
This object indicates the version of the internal format of the Compressed data (the version of the convention used).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cmprSltIdx		1.3.6.1.4.1.164.3.3.4.1.1.4
This attribute indicates a unique number of the slot position where the card is inserted. When the unit is stand-alone or this object is not applicable, 255 will be used.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	psA(1), psB(2), clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), notApplicable(255)

cmprPrtIdx		1.3.6.1.4.1.164.3.3.4.1.1.5
This object indicates a unique identifier of the port, the compressed information relates to. For DXC - according to the order in the card of cmprSltIdx: - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: * For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . For FCD: see product's specification. If the port number is irrelevant to this parameter (if it is a system/card level alarm) the value will be 9999.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

cmprObj		1.3.6.1.4.1.164.3.3.4.1.1.6
This object is the compressed information itself, according to a predefined format, both agent and NMS agreed about.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

mapLinkTable		1.3.6.1.4.1.164.3.3.4.2
A table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MapLinkEntry

mapLinkEntry		1.3.6.1.4.1.164.3.3.4.2.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	MapLinkEntry

mapLinkIdx		1.3.6.1.4.1.164.3.3.4.2.1.1
A unique identifier of the link
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

mapLinkSlotIdx		1.3.6.1.4.1.164.3.3.4.2.1.2
This attribute indicates a unique slot position where the module is inserted.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), standAlone(255)

mapLinkPortIdx		1.3.6.1.4.1.164.3.3.4.2.1.3
This attribute indicates a unique port number. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside, SP. In the DXC : - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: * For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 .
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

mapLinkState		1.3.6.1.4.1.164.3.3.4.2.1.4
This attribute indicates the status of the link between the two muxes
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), down(2), up(3)

alrGenTable		1.3.6.1.4.1.164.3.3.4.3
A table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlrGenEntry

alrGenEntry		1.3.6.1.4.1.164.3.3.4.3.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	AlrGenEntry

alrGenCode		1.3.6.1.4.1.164.3.3.4.3.1.1
This object is a unique code number, identifying a certain alarm.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

alrGenDescription		1.3.6.1.4.1.164.3.3.4.3.1.2
This entry is a unique text description, of the alarm corresponding to the specified code.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

alrGenLevel		1.3.6.1.4.1.164.3.3.4.3.1.3
Alarm level.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), system(2), card(3), port(4)

alrGenSlotType		1.3.6.1.4.1.164.3.3.4.3.1.4
Slot type that the alarm is relevant to. clAndIo - an alarm that is relevant for both CL and IO slots.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), ps(2), cl(3), io(4), clAndIo(5)

alrGenSeverity		1.3.6.1.4.1.164.3.3.4.3.1.5
This object enables the user to select a severity for each alarm. The severity is set per alarm code (same for all slots/ports using this code).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), event(3), minor(4), major(5), warning(6), critical(7)

alrGenDebounce		1.3.6.1.4.1.164.3.3.4.3.1.6
Debounce time for each alarm code, in seconds. The meaning is, that an alarm will be 'declared' as ON (or OFF), only after it was actually ON/OFF the Debouncing time selected by user. 0 = default debounce selection (each alarm has a default value). 250 = maximum value of seconds for debounce. 253 = mask = the alarm will Never be reported. 254 = default debounce selection (each alarm has a default value). 255 = not applicable
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..255

alrGenDefSeverity		1.3.6.1.4.1.164.3.3.4.3.1.7
This object reports the default severity of each alarm. User can change the severity of the alarms defined by this default via the alrGenSeverity object.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), event(3), minor(4), major(5), warning(6), critical(7)

dacsMuxEvents		1.3.6.1.4.1.164.3.3.0
The events for DACS MUX.
Status: current	Access: read-only
OBJECT-IDENTITY

sanityCheckTrap		1.3.6.1.4.1.164.3.3.0.1
This trap is sent after a data base download attempt. It returns the sanity result status and the configuration no.checked.
Status: current	Access: read-only
NOTIFICATION-TYPE

dacsMuxAlarmsTrap		1.3.6.1.4.1.164.3.3.0.2
This trap is sent when an alarm occurs.
Status: current	Access: read-only
NOTIFICATION-TYPE

mdlConnectTrap		1.3.6.1.4.1.164.3.3.0.3
This trap is sent when a card is removed.
Status: current	Access: read-only
NOTIFICATION-TYPE

sysAlrStatusTrap		1.3.6.1.4.1.164.3.3.0.4
This trap is sent upon any change in the value of any of the variables.
Status: current	Access: read-only
NOTIFICATION-TYPE

sysStatusChangedTrap		1.3.6.1.4.1.164.3.3.0.5
This trap is sent when Leds status is changed.
Status: current	Access: read-only
NOTIFICATION-TYPE

cnfgUpdateTrap		1.3.6.1.4.1.164.3.3.0.6
This trap is sent upon change of the active Configuration DB.
Status: current	Access: read-only
NOTIFICATION-TYPE

sysRedundancyStatusTrap		1.3.6.1.4.1.164.3.3.0.7
The trap is sent upon change in Redundancy Status.
Status: current	Access: read-only
NOTIFICATION-TYPE

sysRedundancyActiveCardTrap		1.3.6.1.4.1.164.3.3.0.8
The trap is sent upon change of Active Main/CL Card.
Status: current	Access: read-only
NOTIFICATION-TYPE

sysRedundancyActivePortTrap		1.3.6.1.4.1.164.3.3.0.9
The trap is sent upon change of Active Port of Redundancy Group.
Status: current	Access: read-only
NOTIFICATION-TYPE

services		1.3.6.1.4.1.164.6.3
OBJECT IDENTIFIER

wfq		1.3.6.1.4.1.164.6.3.1
OBJECT IDENTIFIER

wfqTable		2.1
This table allows user to define several WFQ tables per output port. WFQ supports flows with different bandwidth requirements by giving each queue a weight that assigns it a different percentage of output port bandwidth. When Weighted Fair Queuing is used, it is possible to precisely attribute bandwidth partitioning among the queues. When there is congestion, each class (queue) is not allowed to use more bandwidth than the amount allocated to it.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WfqEntry

wfqEntry		2.1.1
An entry in the Weighted Fair Queueing table.
Status: current	Access: not-accessible
OBJECT-TYPE
	WfqEntry

wfqCnfgIdx		2.1.1.1
This object indicates the Idx of the Agent Cnfg the following objects refer. 255=Temporary Cnfg (when relevant, Set is done only to this configuration). For Agents that support only one configuration, this object will be constant=1.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..255

wfqPrtIdx		2.1.1.2
This object indicates a unique port or interface number, for which Weighted Fair Queueing table is applicable . For numbering, see product's spec. For some products, the numbering can equal ifIndex. Value of 255 (not applicable) refer to system level queue
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

wfqTblIdx		2.1.1.3
This object indicates which Weighted Fair Queueing (WFQ) Table is being used. There can be several tables. For FCD-155 User will select which one will be used for a virtual concatenation group.Valid values are 1,2
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

wfqQueueIdx		2.1.1.4
This object indicates a queue index. For FCD-155, valid queues are 1..3. The 4th queue is not in MIB. Its weight will be RO, Calculated according to the sum of the 3 first queues.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

wfqRowStatus		2.1.1.5
This object enables Creation/Deletion of rows in the WFQ table. For FCD-155, rows are not created nor destroyed by user.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

wfqWeightValue		2.1.1.6
This object indicates a relative weight value. User should make sure that the sum of values for all queues will not exceed 100% (sum should be BELOW 100% in order to leave some BW percentage for last queue) Note that when this attribute is being used, the wfqMinRateAbsolute attribute is NA.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..100

wfqSchedulingMode		2.1.1.7
This object controls which scheduling mode is used: Weighted Fair Queuing (WFQ) scheme or priority Queue (Strict Priority).
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disable(2), enable(3)

wfqMinRateAbsolute		2.1.1.8
The minimum absolute rate, in kbps, that should be allocated to this queue. If the value is zero, then there is effectively no minimum rate guarantee. If the value is non-zero, then the servicing of this queue in at least this rate is assured. Note that when this attribute is being used, the wfqWeightValue attribute is NA.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

wfqMaxPacketSize		2.1.1.9
The size of the largest packet which can be received on this queue, specified in octets. Packets larger than this size will be discarded.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

dscpMapping		1.3.6.1.4.1.164.6.3.2
OBJECT IDENTIFIER

dscpMappingTable		1.3.6.1.4.1.164.6.3.2.1
Mapping of DSCP value to a regenerated priority level.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DscpMappingEntry

dscpMappingEntry		1.3.6.1.4.1.164.6.3.2.1.1
An entry in dscpMappingTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	DscpMappingEntry

dscpMappingCnfgIdx		1.3.6.1.4.1.164.6.3.2.1.1.1
This object indicates the Idx of the Agent Cnfg the following objects refer to. 255=Temporary Cnfg (when relevant, Set is done only to this configuration). For Agents that support only one configuration, this object will be constant=1. This object can be used to carry additional indexing (e.g port index) when needed.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..2147483647

dscpMappingDscpIdx		1.3.6.1.4.1.164.6.3.2.1.1.2
DSCP value of the incoming IP packet
Status: current	Access: not-accessible
OBJECT-TYPE
	Dscp

dscpMappingRegenPriority		1.3.6.1.4.1.164.6.3.2.1.1.3
The Regenerated Priority level the incoming DSCP value is mapped to. For FCD-155, valid values are 0,1,2,3
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

ifTeQos		1.3.6.1.4.1.164.6.3.3
OBJECT IDENTIFIER

ifTeQosTable		1.3.6.1.4.1.164.6.3.3.1
The TE QOS Interface Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IfTeQosEntry

ifTeQosEntry		1.3.6.1.4.1.164.6.3.3.1.1
An entry in the TE QOS Interface table.
Status: current	Access: not-accessible
OBJECT-TYPE
	IfTeQosEntry

ifTeQosIdx1		1.3.6.1.4.1.164.6.3.3.1.1.1
This object indicates the 1st Index of the table.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

ifTeQosIdx2		1.3.6.1.4.1.164.6.3.3.1.1.2
This object indicates the 2nd Index of the table.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

ifTeQosIdx3		1.3.6.1.4.1.164.6.3.3.1.1.3
This object indicates the 3rd Index of the table.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

ifTeQosParam		1.3.6.1.4.1.164.6.3.3.1.1.4
This object is used for QOS attributes of the entry's entities.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

ifTeQosParam2		1.3.6.1.4.1.164.6.3.3.1.1.5
This object is used for 2nd group QOS attributes of the entry's entities.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

ifTeQosStatus		1.3.6.1.4.1.164.6.3.3.1.1.6
This object is used to create, activate and destroy entries of this table.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	active(1), createAndGo(4), destroy(6)

portQos		1.3.6.1.4.1.164.6.3.4
OBJECT IDENTIFIER

prtPriorityTable		1.3.6.1.4.1.164.6.3.4.1
A table - Parameters per port per Priority .
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtPriorityEntry

prtPriorityEntry		1.3.6.1.4.1.164.6.3.4.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtPriorityEntry

prtPriorityIdx1		1.3.6.1.4.1.164.6.3.4.1.1.1
This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg. or any other Index.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..255

prtPriorityPrtIdx		1.3.6.1.4.1.164.6.3.4.1.1.2
This object indicates a unique Port Index. Refer to device specification for port Index.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..2147483647

prtPriorityIdx		1.3.6.1.4.1.164.6.3.4.1.1.3
This object indicates the Traffic Priority Index.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..7

prtPriorityIngressRateLimit		1.3.6.1.4.1.164.6.3.4.1.1.4
The maximum rate permitted at Ingress of this port with this Traffic Priority, in Kbps.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

prtQosTable		1.3.6.1.4.1.164.6.3.4.2
Port QoS (Quality of Service) table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrtQosEntry

prtQosEntry		1.3.6.1.4.1.164.6.3.4.2.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrtQosEntry

prtQosIdx		1.3.6.1.4.1.164.6.3.4.2.1.1
The first index of the table. This attribute might indicate the Idx of the Cnfg (1..255) being accessed ; Idx of 255 relates to the TmpCnfg or any other Index.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

prtQosPrtIdx		1.3.6.1.4.1.164.6.3.4.2.1.2
This object indicates a unique Port Index. Refer to device specification for port Index.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

prtQosDirection		1.3.6.1.4.1.164.6.3.4.2.1.3
This object indicates the port's QoS Direction.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	all(1), ingress(2), egress(3)

prtQosRateLimitPacketType		1.3.6.1.4.1.164.6.3.4.2.1.4
This object indicates the Type of Packets on which Rate Limitation is applied.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	all(1), bcastAndMcastAndFloodedUcast(2), bcastAndMcast(3), bcast(4)

prtQosRateLimitCIR		1.3.6.1.4.1.164.6.3.4.2.1.5
This object indicates the port's CIR (Committed Information Rate) in Kbps. Value=0 represents best effort.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

prtQosRateLimitCBS		1.3.6.1.4.1.164.6.3.4.2.1.6
This object indicates the port's CBS (Committed Burst Size) in KB. Value=0 represents best effort.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

prtQosRateLimitEIR		1.3.6.1.4.1.164.6.3.4.2.1.7
This object indicates the port's EIR (Excess Information Rate) in Kbps.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

prtQosRateLimitEBS		1.3.6.1.4.1.164.6.3.4.2.1.8
This object indicates the port's EBS (Excess Burst Size) in KB.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

prtTrafficClass		1.3.6.1.4.1.164.6.3.5
OBJECT IDENTIFIER

portTrafficClassTable		1.3.6.1.4.1.164.6.3.5.1
Mapping of port to Traffic Class level.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PortTrafficClassEntry

portTrafficClassEntry		1.3.6.1.4.1.164.6.3.5.1.1
An entry in portTrafficClassTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	PortTrafficClassEntry

portTrafficClassIdx1		1.3.6.1.4.1.164.6.3.5.1.1.1
This attribute indicates the 1st index of the table. This may be the Idx of the Cnfg(1..255) being accessed; Idx of 255 relates to the TmpCnfg, or any other Index.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..255

portTrafficClassPortIdx		1.3.6.1.4.1.164.6.3.5.1.1.2
This object indicates a unique Port Index. Refer to device specification for port Index.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..2147483647

portTrafficClass		1.3.6.1.4.1.164.6.3.5.1.1.3
This object indicates the Traffic Class level of this port.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..7

serviceTable		1.3.6.1.4.1.164.6.3.6
Table of services.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ServiceEntry

serviceEntry		1.3.6.1.4.1.164.6.3.6.1
An entry in the Service Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	ServiceEntry

flowIndex		1.3.6.1.4.1.164.6.3.6.1.1
Defines the Flow ID the service is associated to.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

serviceIndex		1.3.6.1.4.1.164.6.3.6.1.2
Defines the Service ID - according to the CoS.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	0..7

serviceRowStatus		1.3.6.1.4.1.164.6.3.6.1.3
This attribute is used to create a new row or to delete an existing row in the table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

serviceName		1.3.6.1.4.1.164.6.3.6.1.4
This attribute defines the service name.
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString

serviceBwProfileId		1.3.6.1.4.1.164.6.3.6.1.5
This variable holds the index of the Ingress BW profile assigned to that service.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

evcCosTable		1.3.6.1.4.1.164.6.3.7
This table defines mapping of Ethernet Virtual Connection (EVC) ID to Class of Service (CoS) ID
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EvcCosEntry

evcCosEntry		1.3.6.1.4.1.164.6.3.7.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	EvcCosEntry

evcCosCnfgIdx		1.3.6.1.4.1.164.6.3.7.1.1
This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..255

evcCosEvcIdx		1.3.6.1.4.1.164.6.3.7.1.2
This attribute indicates EVC Id.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..4095

evcCosRowStatus		1.3.6.1.4.1.164.6.3.7.1.3
This attribute allows to create/delete a row in this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

evcCosEvcName		1.3.6.1.4.1.164.6.3.7.1.5
A string that identifies the EVC. It should be unique in the Maintenance Domain (i.e., in the managed network) Used as MEG ID field in OAM messages.
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString

evcCosSpVlanId		1.3.6.1.4.1.164.6.3.7.1.6
This object indicates the SP (Service Provider) VLAN used when sending an OAM message for the specified EVC.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

serviceStatTable		1.3.6.1.4.1.164.6.3.8
Service statistics table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ServiceStatEntry

serviceStatEntry		1.3.6.1.4.1.164.6.3.8.1
An entry in the Service Statistics Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	ServiceStatEntry

serviceStatDirection		1.3.6.1.4.1.164.6.3.8.1.1
The direction in wich the measurement is taken.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	upstream(1), downstream(2)

srvForwardGreenPackets		1.3.6.1.4.1.164.6.3.8.1.2
This attribute displays the counted number of forwarded packets that where marked Green.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

srvForwardGreenPacktesOverflow		1.3.6.1.4.1.164.6.3.8.1.3
This attribute displays the number of times that the forwardGreenPackets counter has overflowed.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

srvForwardYellowPackets		1.3.6.1.4.1.164.6.3.8.1.4
This attribute displays the counted number of forwarded packets that where marked Yellow.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

srvForwardYellowPacketsOverflow		1.3.6.1.4.1.164.6.3.8.1.5
This attribute displays the number of times that the forwardYellowPackets counter has overflowed.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

srvDiscardGreenPacket		1.3.6.1.4.1.164.6.3.8.1.6
This attribute displays the counted number of discarded packets that where marked Green.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

srvDiscardGreenPacketOverflow		1.3.6.1.4.1.164.6.3.8.1.7
This attribute displays the number of times that the discardGreenPacket counter has overflowed.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

srvDiscardYellowRedPackets		1.3.6.1.4.1.164.6.3.8.1.8
This attribute displays the counted number of discarded packets that where marked Yellow or Red.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

srvDiscardYellowRedPacketsOverflow		1.3.6.1.4.1.164.6.3.8.1.9
This attribute displays the number of times that the discardYellowRedPackets counter has overflowed.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

srvForwardGreenBytes		1.3.6.1.4.1.164.6.3.8.1.10
This attribute displays the counted number of forwarded bytes that where marked Green.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

srvForwardGreenBytesOverflow		1.3.6.1.4.1.164.6.3.8.1.11
This attribute displays the number of times that the forwardGreenBytes counter has overflowed.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

srvForwardYellowBytes		1.3.6.1.4.1.164.6.3.8.1.12
This attribute displays the counted number of forwarded bytes that where marked Yellow.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

srvForwardYellowBytesOverflow		1.3.6.1.4.1.164.6.3.8.1.13
This attribute displays the number of times that the forwardYellowBytes counter has overflowed.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

srvDiscardGreenBytes		1.3.6.1.4.1.164.6.3.8.1.14
This attribute displays the counted number of discarded bytes that where marked Green.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

srvDiscardGreenBytesOverflow		1.3.6.1.4.1.164.6.3.8.1.15
This attribute displays the number of times that the discardGreenBytes counter has overflowed.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

srvDiscardYellowRedBytes		1.3.6.1.4.1.164.6.3.8.1.16
This attribute displays the counted number of discarded bytes that where marked Yellow or Red.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

srvDiscardYellowRedBytesOverflow		1.3.6.1.4.1.164.6.3.8.1.17
This attribute displays the number of times that the discardYellowRedBytes counter has overflowed.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

srvResetStatsCmd		1.3.6.1.4.1.164.6.3.8.1.18
Reset statistic counters of the service.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	off(2), on(3)

srvDiscardYellowPackets		1.3.6.1.4.1.164.6.3.8.1.19
This attribute displays the counted number of discarded packets that where marked Yellow.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

srvDiscardYellowPacketsOverflow		1.3.6.1.4.1.164.6.3.8.1.20
This attribute displays the number of times that the discardYellowPackets counter has overflowed.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

srvDiscardYellowBytes		1.3.6.1.4.1.164.6.3.8.1.21
This attribute displays the counted number of discarded bytes that where marked Yellow.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

srvDiscardYellowBytesOverflow		1.3.6.1.4.1.164.6.3.8.1.22
This attribute displays the number of times that the discardYellowBytes counter has overflowed.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

srvDiscardRedPackets		1.3.6.1.4.1.164.6.3.8.1.23
This attribute displays the counted number of discarded packets that where marked Red.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

srvDiscardRedPacketsOverflow		1.3.6.1.4.1.164.6.3.8.1.24
This attribute displays the number of times that the discardRedPackets counter has overflowed.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

srvDiscardRedBytes		1.3.6.1.4.1.164.6.3.8.1.25
This attribute displays the counted number of discarded bytes that where marked Red.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

srvDiscardRedBytesOverflow		1.3.6.1.4.1.164.6.3.8.1.26
This attribute displays the number of times that the discardRedBytes counter has overflowed.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

mappingProfileObjects		1.3.6.1.4.1.164.6.3.9
OBJECT IDENTIFIER

flowMappingProfileTable		1.3.6.1.4.1.164.6.3.9.1
This table holds flow mapping profiles.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FlowMappingProfileEntry

flowMappingProfileEntry		1.3.6.1.4.1.164.6.3.9.1.1
Each entry in this table describes one Flow mapping profile with one of its Flow Mapping supported, according to the Priority order. The information includes a reference to a Flow Mapping index.
Status: current	Access: not-accessible
OBJECT-TYPE
	FlowMappingProfileEntry

flowMappingProfileIndex		1.3.6.1.4.1.164.6.3.9.1.1.1
A running index for the Flow Mapping Profile table.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

flowMappingProfilePriority		1.3.6.1.4.1.164.6.3.9.1.1.2
The priority of the Mapping selected by flowMappingProfileMapIndex within the Flow Mapping Profile.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER

flowMappingProfileRowStatus		1.3.6.1.4.1.164.6.3.9.1.1.3
This attribute is used to create a new row or to delete an existing row in the table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

flowMappingProfileNumOfMaps		1.3.6.1.4.1.164.6.3.9.1.1.4
This attribute determines the number of the mappings associated to the Flow Mapping Profile.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

flowMappingProfileMapIndex		1.3.6.1.4.1.164.6.3.9.1.1.5
This attribute holds a reference to the mapping index. It specifies the mapping selected for the Mapping Profile for the selected Priority. When flowMappingProfileNumOfMaps=0, this attribute is not relevant.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

flowMappingProfileName		1.3.6.1.4.1.164.6.3.9.1.1.6
This attribute defines the name assigned to flowMappingIndex profile.
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString

qosFlowMappingTable		1.3.6.1.4.1.164.6.3.9.2
A table of Flow Mapping.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QosFlowMappingEntry

qosFlowMappingEntry		1.3.6.1.4.1.164.6.3.9.2.1
Each entry in this table describes one Flow Mapping. The information includes combination (AND function) of all the classifications, as defined in the qosFlowMappingCriteria field. Classifiers are: TOS, DSCP, VLAN ID, MAC and IP source and destination addresses, IP protocol, IP Precedence, TCP and UDP source and destination ports.
Status: current	Access: not-accessible
OBJECT-TYPE
	QosFlowMappingEntry

qosFlowMappingIdx1		1.3.6.1.4.1.164.6.3.9.2.1.1
- In case the table is accessed via flowMappingProfileTable this is a running index for the QoS Flow Mapping table. - In case the table is not accessed via flowMappingProfileTable, this will be the ifIndex of the XNI (bridge port) to which the QoS mapping applies.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

qosFlowMappingIdx2		1.3.6.1.4.1.164.6.3.9.2.1.2
An index for the QoS Flow Mapping table. - In case the table is accessed via flowMappingProfileTable the index will be fixed = 1. - In case the table is not accessed via flowMappingProfileTable, this will be the index of the Flow (EVC) to which the QoS mapping applies.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

qosFlowMappingIdx3		1.3.6.1.4.1.164.6.3.9.2.1.3
An index for the QoS Flow Mapping table. - In case the table is accessed via flowMappingProfileTable the index will be fixed = 1. - In case the table is not accessed via flowMappingProfileTable, this will be the Priority to which the QoS mapping applies.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

qosFlowMappingRowStatus		1.3.6.1.4.1.164.6.3.9.2.1.4
This attribute is used to create a new row or to delete an existing row in the table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

qosFlowMappingCriteria		1.3.6.1.4.1.164.6.3.9.2.1.5
This attribute determines upon which criterion the flow will be mapped.
Status: current	Access: read-create
OBJECT-TYPE
	BITS	ieee802dot1p(0), tos(1), dscp(2), vlanId(3), macSrcAddr(4), macDestAddr(5), ipSrcAddr(6), ipDestAddr(7), tcpSrcPort(8), tcpDestPort(9), udpSrcPort(10), udpDestPort(11), ipPrecedence(12), innerIeee802dot1p(13), innerVlanId(14), untagged(15)

qosFlowMappingIeee802dot1p		1.3.6.1.4.1.164.6.3.9.2.1.6
This attribute determines which TOS values are applicable for that flow. Each bit (0..7) represents a different 802.1 P-bit value. Setting '1' to the bit means that the corresponding 802.1 P-bit value is applicable. It is relevant only in case the ieee802dot1p bit(0) in qosFlowMappingCriteria equals 1.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

qosFlowMappingTos		1.3.6.1.4.1.164.6.3.9.2.1.7
This attribute determines which TOS values are applicable for that flow. Each bit (0..7) represents a different TOS value. Setting '1' to the bit means that the corresponding TOS value is applicable. It is relevant only in case the tos bit (1) in qosFlowMappingCriteria equals 1.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

qosFlowMappingFromDscp		1.3.6.1.4.1.164.6.3.9.2.1.8
This attribute determines the first DSCP value to compare with in a range. It is relevant only in case the dscp bit (2) in qosFlowMappingCriteria equals 1.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

qosFlowMappingToDscp		1.3.6.1.4.1.164.6.3.9.2.1.9
This attribute determines the first DSCP value to compare with in a range. It is relevant only in case the dscp bit (2) in qosFlowMappingCriteria equals 1.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

qosFlowMappingFromVlanId		1.3.6.1.4.1.164.6.3.9.2.1.10
This attribute determines the first VLAN ID value to compare with in a range. It is relevant only in case the vlanId bit (3) in qosFlowMappingCriteria equals 1.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

qosFlowMappingToVlanId		1.3.6.1.4.1.164.6.3.9.2.1.11
This attribute determines the last VLAN ID value to compare with in a range. It is relevant only in case the vlanId bit (3) in qosFlowMappingCriteria equals 1.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

qosFlowMappingFromSrcMacAddr		1.3.6.1.4.1.164.6.3.9.2.1.12
This attribute determines the first source MAC address to compare with in a range. It is relevant only in case the macSrcAddr bit (4) in qosFlowMappingCriteria equals 1.
Status: current	Access: read-create
OBJECT-TYPE
	MacAddress

qosFlowMappingToSrcMacAddr		1.3.6.1.4.1.164.6.3.9.2.1.13
This attribute determines the last source MAC address to compare with in a range. It is relevant only in case the macSrcAddr bit (4) in qosFlowMappingCriteria equals 1.
Status: current	Access: read-create
OBJECT-TYPE
	MacAddress

qosFlowMappingFromDestMacAddr		1.3.6.1.4.1.164.6.3.9.2.1.14
This attribute determines the first destination MAC address to compare with in a range. It is relevant only in case the macDestAddr (5) bit in qosFlowMappingCriteria equals 1.
Status: current	Access: read-create
OBJECT-TYPE
	MacAddress

qosFlowMappingToDestMacAddr		1.3.6.1.4.1.164.6.3.9.2.1.15
This attribute determines the last destination MAC address to compare with in a range. It is relevant only in case the macDestAddr (5) bit in qosFlowMappingCriteria equals 1.
Status: current	Access: read-create
OBJECT-TYPE
	MacAddress

qosFlowMappingFromSrcIpAddr		1.3.6.1.4.1.164.6.3.9.2.1.16
This attribute determines the first source IP address to compare with in a range. It is relevant only in case the ipSrcAddr (6) bit in qosFlowMappingCriteria equals 1.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

qosFlowMappingToSrcIpAddr		1.3.6.1.4.1.164.6.3.9.2.1.17
This attribute determines the last source IP address to compare with in a range. It is relevant only in case the ipSrcAddr (6) bit in qosFlowMappingCriteria equals 1.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

qosFlowMappingFromDestIpAddr		1.3.6.1.4.1.164.6.3.9.2.1.18
This attribute determines the first destination IP address to compare with in a range. It is relevant only in case the ipDestAddr (7) bit in qosFlowMappingCriteria equals 1.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

qosFlowMappingToDestIpAddr		1.3.6.1.4.1.164.6.3.9.2.1.19
This attribute determines the last destination IP address to compare with in a range. It is relevant only in case the ipDestAddr (7) bit in qosFlowMappingCriteria equals 1.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

qosFlowMappingFromTcpSrcPort		1.3.6.1.4.1.164.6.3.9.2.1.20
This attribute determines the first TCP source port to compare with in a range. It is relevant only in case the tcpSrcPort bit (8) in qosFlowMappingCriteria equals 1.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

qosFlowMappingToTcpSrcPort		1.3.6.1.4.1.164.6.3.9.2.1.21
This attribute determines the last TCP source port to compare with in a range. It is relevant only in case the tcpSrcPort bit (8) in qosFlowMappingCriteria equals 1.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

qosFlowMappingFromTcpDestPort		1.3.6.1.4.1.164.6.3.9.2.1.22
This attribute determines the first TCP destination port to compare with in a range. It is relevant only in case the tcpDestPort bit (9) in qosFlowMappingCriteria equals 1.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

qosFlowMappingToTcpDestPort		1.3.6.1.4.1.164.6.3.9.2.1.23
This attribute determines the last TCP destination port to compare with in a range. It is relevant only in case the tcpDestPort bit (9) in qosFlowMappingCriteria equals 1.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

qosFlowMappingFromUdpSrcPort		1.3.6.1.4.1.164.6.3.9.2.1.24
This attribute determines the first UDP source port to compare with in a range. It is relevant only in case the udpSrcPort bit (10) in qosFlowMappingCriteria equals 1.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

qosFlowMappingToUdpSrcPort		1.3.6.1.4.1.164.6.3.9.2.1.25
This attribute determines the last UDP source port to compare with in a range. It is relevant only in case the udpSrcPort bit (10) in qosFlowMappingCriteria equals 1.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

qosFlowMappingFromUdpDestPort		1.3.6.1.4.1.164.6.3.9.2.1.26
This attribute determines the first UDP destination port to compare with in a range. It is relevant only in case the udpDestPort bit (11) in qosFlowMappingCriteria equals 1.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

qosFlowMappingToUdpDestPort		1.3.6.1.4.1.164.6.3.9.2.1.27
This attribute determines the last UDP destination port to compare with in a range. It is relevant only in case the udpDestPort bit (11) in qosFlowMappingCriteria equals 1.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

qosFlowMappingFromIpPrecedence		1.3.6.1.4.1.164.6.3.9.2.1.28
This attribute determines the first IpPrecedence value to compare with in a range. It is relevant only in case the IpPrecedence bit (12) in qosFlowMappingCriteria equals 1.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

qosFlowMappingToIpPrecedence		1.3.6.1.4.1.164.6.3.9.2.1.29
This attribute determines the last IpPrecedence value to compare with in a range. It is relevant only in case the IpPrecedence bit (12) in qosFlowMappingCriteria equals 1.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

qosFlowMappingInnerIeee802dot1p		1.3.6.1.4.1.164.6.3.9.2.1.30
This attribute determines which TOS values are applicable for that flow. Each bit (0..7) represents a different inner 802.1 P-bit value. Setting '1' to the bit means that the corresponding inner 802.1 P-bit value is applicable. It is relevant only in case the innerIeee802dot1p bit (13) in qosFlowMappingCriteria equals 1.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

qosFlowMappingFromInnerVlanId		1.3.6.1.4.1.164.6.3.9.2.1.31
This attribute determines the first inner VLAN ID value to compare with in a range. It is relevant only in case the innerVlanId bit(14) in qosFlowMappingCriteria equals 1.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

qosFlowMappingToInnerVlanId		1.3.6.1.4.1.164.6.3.9.2.1.32
This attribute determines the last inner VLAN ID value to compare with in a range. It is relevant only in case the innerVlanId bit(14) in qosFlowMappingCriteria equals 1.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

cosProfileTable		1.3.6.1.4.1.164.6.3.10
Class of Service Profile table. Each profile holds a priority method, and a mappring function that maps the priority values (range according to the method) into CoS values.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CosProfileEntry

cosProfileEntry		1.3.6.1.4.1.164.6.3.10.1
A conceptual row where each row contains one CoS attributes.
Status: current	Access: not-accessible
OBJECT-TYPE
	CosProfileEntry

cosProfileIndex		1.3.6.1.4.1.164.6.3.10.1.1
Defines the CoS Profile ID.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

cosProfileRowStatus		1.3.6.1.4.1.164.6.3.10.1.2
This attribute is used to create a new row or to delete an existing row in the table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

cosProfileCosMethod		1.3.6.1.4.1.164.6.3.10.1.3
Defines the priority method upon CoS mapping is done.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	ieee802dot1p(2), tos(3), dscp(4), ipPrecedence(5)

cosProfileName		1.3.6.1.4.1.164.6.3.10.1.4
This attribute defines the name assigned to CoS profile.
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString

cosProfileCosMapping		1.3.6.1.4.1.164.6.3.10.1.5
This attribute defines the value of the CoS that is assigned for each priority. The number of the valid octets depends upon the priority method selected: Octet 0 corresponds to priority = 0 Octet 1 corresponds to priority = 1 ... Octet 63 corresponds to priority = 63.
Status: current	Access: read-create
OBJECT-TYPE
	OCTET STRING	Size(0..63)

queueProfileObjects		1.3.6.1.4.1.164.6.3.11
OBJECT IDENTIFIER

qProfileTable		1.3.6.1.4.1.164.6.3.11.1
This table defines the profiles for a cluster of queues.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QProfileEntry

qProfileEntry		1.3.6.1.4.1.164.6.3.11.1.1
A conceptual row where each row contains one Queue Cluster attribute.
Status: current	Access: not-accessible
OBJECT-TYPE
	QProfileEntry

qProfileIndex		1.3.6.1.4.1.164.6.3.11.1.1.1
Defines the Queue Cluster Profile ID.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

qProfileRowStatus		1.3.6.1.4.1.164.6.3.11.1.1.2
This attribute is used to create a new row or to delete an existing row in the table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

qProfileName		1.3.6.1.4.1.164.6.3.11.1.1.3
This attribute holds the name of the Queue cluster profile.
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString

qProfileNumberOfInternalQ		1.3.6.1.4.1.164.6.3.11.1.1.4
This attribute holds the number of the internal queue profiles that are pointed by qInternalQProfile.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

qProfileInternalQProfile		1.3.6.1.4.1.164.6.3.11.1.1.5
This attribute holds the indexes to the queue profiles in the qInternalProfileTable. Each couple of octets holds an index to the qInternalProfileTable.
Status: current	Access: read-create
OBJECT-TYPE
	OCTET STRING

qInternalProfileTable		1.3.6.1.4.1.164.6.3.11.2
This table holds queue profiles.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QInternalProfileEntry

qInternalProfileEntry		1.3.6.1.4.1.164.6.3.11.2.1
A conceptual row where each row contains one Queue attribute.
Status: current	Access: not-accessible
OBJECT-TYPE
	QInternalProfileEntry

qInternalProfileIndex		1.3.6.1.4.1.164.6.3.11.2.1.1
Defines the Queue Profile ID.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

qInternalProfileRowStatus		1.3.6.1.4.1.164.6.3.11.2.1.2
This attribute is used to create a new row or to delete an existing row in the table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

qInternalProfileScheduling		1.3.6.1.4.1.164.6.3.11.2.1.3
This attribute determines the queue scheduling method.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	wfq(1), strict(2), bestEffort(3)

qInternalProfileWFQWeight		1.3.6.1.4.1.164.6.3.11.2.1.4
This attribute determines the weight that each WFQ (Weighted Fair Queue) participant gets. It is applicable only when scheduling is configured to WFQ.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

qInternalProfileQueueLength		1.3.6.1.4.1.164.6.3.11.2.1.5
This attribute determines the length of the queue.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

qInternalProfileWredStartDropThresh		1.3.6.1.4.1.164.6.3.11.2.1.6
This attribute determines the length that the queue (Start Value) must reach before the packets colored yellow will start being dropped by the WRED (Weighted Random Early Detection/Discard) mechanism. WRED is one the most commonly used method for congestion avoidance.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

qInternalProfileWredDropAllThresh		1.3.6.1.4.1.164.6.3.11.2.1.7
This attribute determines the length that the queue (Stop Value) must reach before the WRED (Weighted Random Early Detection) shaper mechanism stops dropping randomly, and just drops all further packets marked as yellow.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

qInternalProfileWredDropProbability		1.3.6.1.4.1.164.6.3.11.2.1.8
This attribute determines the percentage of packets that are being dropped at the point when the length of the queue reaches the Stop value. So, effectively, this defines how quickly the rate of dropping packet must increase as the queue length grows from the Start Value to the Stop Value.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

qInternalProfileRateLimit		1.3.6.1.4.1.164.6.3.11.2.1.9
This attribute determines the Rate Limit of the queue in Kbps. Value=0 represents best effort.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

qInternalProfileShaperProfile		1.3.6.1.4.1.164.6.3.11.2.1.10
This attribute defines the Shaper Profile (bwProfileIndex from bwProfileTable) assigned to this qInternalProfile. Valid range of bwProfileIndex for Shaper Profiles is 0x8000001-0x8000041. If set to '0', no profile is assigned to this qInternalProfile.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

queueGroupTable		1.3.6.1.4.1.164.6.3.11.3
This table defines the queue groups/blocks,their level and connections between them.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QueueGroupEntry

queueGroupEntry		1.3.6.1.4.1.164.6.3.11.3.1
A conceptual row where each row contains one Queue group.
Status: current	Access: not-accessible
OBJECT-TYPE
	QueueGroupEntry

queueGroupName		1.3.6.1.4.1.164.6.3.11.3.1.1
Defines the Queue Group unique name.
Status: current	Access: not-accessible
OBJECT-TYPE
	SnmpAdminString	Size(1..32)

queueGroupQBlockLevel		1.3.6.1.4.1.164.6.3.11.3.1.2
This attribute holds the Level of the Queue Block .First level is 1. NA=2^32-1.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

queueGroupQBlockIdx		1.3.6.1.4.1.164.6.3.11.3.1.3
This attribute holds the ID of the Queue Block. NA=2^32-1.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

queueGroupRowStatus		1.3.6.1.4.1.164.6.3.11.3.1.4
This attribute is used to create a new row or to delete an existing row in the table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

queueGroupQBlockProfile		1.3.6.1.4.1.164.6.3.11.3.1.5
This attribute defines the Queue profile assigned to this Queue Block. This object points to qProfileIndex in qProfileTable.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

queueGroupQBlockShaperProfile		1.3.6.1.4.1.164.6.3.11.3.1.6
This attribute defines the Shaper profile assigned to this Queue Block.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

queueGroupPointToQBlock		1.3.6.1.4.1.164.6.3.11.3.1.7
This attribute defines the Queue Block name of the next Queue Block level that is pointed by this Queue Block.
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString	Size(1..32)

queueGroupPointToInternalQueue		1.3.6.1.4.1.164.6.3.11.3.1.8
This attribute defines the internal queue whithin queueGroupPointToQBlock that is pointed by this Queue Block.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

queueGroupQBlockName		1.3.6.1.4.1.164.6.3.11.3.1.9
This attribute holds the name of the Queue Block.
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString	Size(1..32)

markingProfileTable		1.3.6.1.4.1.164.6.3.12
Marking profile table. Each profile holds a marking function which converts CoS values to Service Provider priority values.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MarkingProfileEntry

markingProfileEntry		1.3.6.1.4.1.164.6.3.12.1
A conceptual row where each row contains one Marking attribute.
Status: current	Access: not-accessible
OBJECT-TYPE
	MarkingProfileEntry

markingProfileIndex		1.3.6.1.4.1.164.6.3.12.1.1
Defines the Marking Profile ID.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

markingProfileRowStatus		1.3.6.1.4.1.164.6.3.12.1.2
This attribute is used to create a new row or to delete an existing row in the table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

markingProfileName		1.3.6.1.4.1.164.6.3.12.1.3
This attribute defines the unique name assigned to the Marking profile.
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString

markingSpVlanPBit		1.3.6.1.4.1.164.6.3.12.1.4
For ETX-202A : This attribute defines the value of the SP VLAN P-Bit that is assigned for each CoS: Octet 0 corresponds to CoS = 0 Octet 1 corresponds to CoS = 1 ... Octet 7 corresponds to CoS = 7. For LA-210 from V1.5 : This attribute defines the value of the SP VLAN P-Bit that is assigned for each frame according to the value of markingProfileMethod parameter : Octet 0 corresponds to value 0 of 802.1 P-bit/DSCP/TOS. Octet 1 corresponds to value 1 of 802.1 P-bit/DSCP/TOS. ... Octet 7 corresponds to value 7 of 802.1 P-bit/DSCP/TOS. Octets 8-63 correspond to DSCP values 8-63.
Status: current	Access: read-create
OBJECT-TYPE
	OCTET STRING	Size(0..63)

markingProfileMethod		1.3.6.1.4.1.164.6.3.12.1.5
This attribute defines the method upon which marking is done.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	ieee802dot1p(2), tos(3), dscp(4), ipPrecedence(5)

ethIf		1.3.6.1.4.1.164.3.1.6.1
OBJECT IDENTIFIER

ethIfTable		1.3.6.1.4.1.164.3.1.6.1.1
A table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EthIfEntry

ethIfEntry		1.3.6.1.4.1.164.3.1.6.1.1.1
An entry in table.
Status: current	Access: not-accessible
OBJECT-TYPE
	EthIfEntry

ethIfIdx		1.3.6.1.4.1.164.3.1.6.1.1.1.1
A unique index of the ethernet interface/port.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ethMode		1.3.6.1.4.1.164.3.1.6.1.1.1.2
This object indicates the Ethernet mode of operation.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	halfDuplex(1), fullDuplex(2), notApplicable(255)

ethBridgingMode		1.3.6.1.4.1.164.3.1.6.1.1.1.3
This object indicates the bridging mode of the Ethernet interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	filtered(1), transparent(2)

ethEncapsulationCRCMode		1.3.6.1.4.1.164.3.1.6.1.1.1.4
This object define the encapsulation type requested for the Ethernet interface. It indicates if we transfer the Ethernet frame to the other side with or without the CRC.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), withCRC(2), withoutCRC(3)

ethBackPressure		1.3.6.1.4.1.164.3.1.6.1.1.1.5
This parameter defines whether to enable or disable Back pressure. Back Pressure is a flow control parameter.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), enable(3)

ethLimit4		1.3.6.1.4.1.164.3.1.6.1.1.1.6
This parameter determine the Back off algorithm mode. Every 4 following collisions the Framer will be thrown out (4 times more than usuall).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), disable(2), enable(3)

ethSkipInitReset		1.3.6.1.4.1.164.3.1.6.1.1.1.7
This parameter defines whether read status on reset.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), notSkip(2), skip(3)

ethMulticastBlock		1.3.6.1.4.1.164.3.1.6.1.1.1.8
This parameter defines whether to send multicast message to WAN from LAN or not.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), unBlock(2), block(3)

ethBroadcastBlock		1.3.6.1.4.1.164.3.1.6.1.1.1.9
This parameter defines whether to send broadcast message to WAN from LAN or not.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), unBlock(2), block(3)

ethSpeed		1.3.6.1.4.1.164.3.1.6.1.1.1.10
This parameter defines the line speed.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), s10Mbps(2), s100Mbps(3), s1Gbps(4)

ethRip2		1.3.6.1.4.1.164.3.1.6.1.1.1.11
This parameter defines whether to send RIP II message to WAN from LAN or not
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), no(2), yes(3)

ethPortPriority		1.3.6.1.4.1.164.3.1.6.1.1.1.12
This parameter defines if priority is to be considered for this Port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), none(2), fixed(3)

ethPortMngEnable		1.3.6.1.4.1.164.3.1.6.1.1.1.13
This parameter defines whether management data can pass through this Port. localOnly (4) - Only local device can be managed via this port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), no(2), yes(3), localOnly(4)

ethFlowCtrlMacAddress		1.3.6.1.4.1.164.3.1.6.1.1.1.14
In case of flow control - transmit frame with this specific MAC address to inform the other end to stop sending frames. Default: 01.80.C2.00.00.01.
Status: current	Access: read-write
OBJECT-TYPE
	MacAddress

ethRateLimit		1.3.6.1.4.1.164.3.1.6.1.1.1.15
This parameter defines the Rate Limit of the line, in Mbps.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

ethJumboFrameEnable		1.3.6.1.4.1.164.3.1.6.1.1.1.16
This parameter defines whether to support Jumbo Frame or not.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), no(2), yes(3)

ethAutoMdiXEnable		1.3.6.1.4.1.164.3.1.6.1.1.1.17
This parameter defines whether to support automatic change between MDI and MDI[X].
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), no(2), yes(3)

ethPortDataEnable		1.3.6.1.4.1.164.3.1.6.1.1.1.18
This parameter defines whether this port is enabled for data (that is not management). no(2) - management can run on this port yes(3) - both management and payload data can run on this port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), no(2), yes(3)

ethIfUse		1.3.6.1.4.1.164.3.1.6.1.1.1.19
This parameter defines the use of the port. 1=NET 2=USER .
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

ethLineOam		1.3.6.1.4.1.164.3.1.6.1.1.1.20
This parameter defines the working mode of 802.AH OAM mechanism.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(2), passive(3)

ethRoutingProtocol		1.3.6.1.4.1.164.3.1.6.1.1.1.21
This parameter defines the routing protocol used above ETH port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), none(2), proprietary(3), rip2(4), rip1and2(6)

ethMdiXManualSwitch		1.3.6.1.4.1.164.3.1.6.1.1.1.22
This parameter sets the port to be MDI-X (cross-over) or MDI (straight-through). It is applicable only when ethAutoMdiXEnable = no, namely, only when the automatic MDI/MDIX crossover function is disabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	crossOver(1), straightThrough(2)

ethDot1xEnable		1.3.6.1.4.1.164.3.1.6.1.1.1.23
Determines if the Port-Based Network Access Protocol (IEEE-802.1x) is enabled for the Ethernet Port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), no(2), yes(3)

ethPartnerRateMode		1.3.6.1.4.1.164.3.1.6.1.1.1.24
For converters having couples of ports, where each couple contains a port with an SFP connector and a port with a RJ connector, this parameter is relevant for the SFP port. It affects Rate configuration of its partner (RJ port). manual - user can configure manually ETH parameters of RJ port (e.g Autonegotiation, Max Capability Advertised, etc...) automatic - SFP Rate will be enforced on the RJ port. In this mode, user cannot configure the Rate related parameters of the RJ port (e.g Autonegotiation, Max Capability Advertised, etc...)
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	manual(1), automatic(2)

ethDot1xPortRole		1.3.6.1.4.1.164.3.1.6.1.1.1.25
Determine the functionality of the port in the Port-Based Network Access Protocol (IEEE-802.1x) - either Authenticator or Supplicant.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	authenticator(1), supplicant(2)

ethIfPerformance		1.3.6.1.4.1.164.3.1.6.1.2
OBJECT IDENTIFIER

ethIfCurrentTable		1.3.6.1.4.1.164.3.1.6.1.2.1
The Ethernet Current table. When the index specifies the Ethernet interface (only), the counters are for an interval of 15 minutes.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EthIfCurrentEntry

ethIfCurrentEntry		1.3.6.1.4.1.164.3.1.6.1.2.1.1
An entry in the Ethernet Current table.
Status: current	Access: not-accessible
OBJECT-TYPE
	EthIfCurrentEntry

ethIfCurrentIndex		1.3.6.1.4.1.164.3.1.6.1.2.1.1.1
The index of the Ethernet interface. It may be ifIndex. For some devices (e.g RICi-622GE), supporting several types of intervals, this index will be a concatenation of the port index and interval type. Interval type can indicate: 1 minute, 15 minutes, 1 hour, 24 hours. For the exact formula, see device specification.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ethIfCurrentStatus		1.3.6.1.4.1.164.3.1.6.1.2.1.1.2
The status of the current interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was partialy out. 4 - notValid - module is out.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(4)

ethIfCurrentInFrames		1.3.6.1.4.1.164.3.1.6.1.2.1.1.3
The counter associated with the number of received frames, encountered by the Ethernet interface in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfCurrentInOctets		1.3.6.1.4.1.164.3.1.6.1.2.1.1.4
The counter associated with the number of received octets, encountered by the Ethernet interface in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfCurrentAlignmentErrors		1.3.6.1.4.1.164.3.1.6.1.2.1.1.5
The counter associated with the number of received frames, which are not complete (The result of dividing the number of bits by 8 is not an Integer), encountered by the Ethernet interface in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfCurrentFCSErrors		1.3.6.1.4.1.164.3.1.6.1.2.1.1.6
The counter associated with the number of received frames that didn't pass the FCS test, encountered by the Ethernet interface in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfCurrentLengthError		1.3.6.1.4.1.164.3.1.6.1.2.1.1.7
The counter associated with the number of received frames with length error, encountered by the Ethernet interface in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfCurrentOutFrames		1.3.6.1.4.1.164.3.1.6.1.2.1.1.8
The counter associated with the number of transmitted frames, encountered by the Ethernet interface in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfCurrentOutOctets		1.3.6.1.4.1.164.3.1.6.1.2.1.1.9
The counter associated with the number of transmitted octets, encountered by the Ethernet interface in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfCurrentSingleCollisionFrames		1.3.6.1.4.1.164.3.1.6.1.2.1.1.10
The counter associated with the number of successfully transmitted frames for which transmission was inhibited by exactly one collision, encountered by the Ethernet interface in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfCurrentMultipleCollisionFrames		1.3.6.1.4.1.164.3.1.6.1.2.1.1.11
The counter associated with the number of successfully transmitted frames for which transmission was inhibited by more than one collision, encountered by the Ethernet interface in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfCurrentDeferredTransmissions		1.3.6.1.4.1.164.3.1.6.1.2.1.1.12
The counter associated with the number of transmitted frames for which the first transmission attempt was delayed due to a busy media, encountered by the Ethernet interface in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfCurrentLateCollisions		1.3.6.1.4.1.164.3.1.6.1.2.1.1.13
The counter associated with the number of times that a collision was detected later than the first 64 bytes of the frame, encountered by the Ethernet interface in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfCurrentCarrierSenseErrors		1.3.6.1.4.1.164.3.1.6.1.2.1.1.14
The counter associated with the number of times that the carrier sense condition was lost or never asserted when attempting to transmit a frame, encountered by the Ethernet interface in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfCurrentInputCongestionDropped		1.3.6.1.4.1.164.3.1.6.1.2.1.1.15
The counter associated with the number of frames dropped due to lack of buffers in ingress pool, encountered by the Ethernet interface in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfCurrentOutputCongestionDropped		1.3.6.1.4.1.164.3.1.6.1.2.1.1.16
The counter associated with the number of dropped frames due to a congestion, encountered by the Transmit direction to the Ethernet interface in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfCurrentOverflowInFrames		1.3.6.1.4.1.164.3.1.6.1.2.1.1.17
The number of times the associated ethIfCurrentInFrames counter has overflowed in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfCurrentOverflowInOctets		1.3.6.1.4.1.164.3.1.6.1.2.1.1.18
The number of times the associated ethIfCurrentInOctets counter has overflowed in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfCurrentOverflowFCSErrors		1.3.6.1.4.1.164.3.1.6.1.2.1.1.19
The number of times the associated ethIfCurrentFCSErrors counter has overflowed in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfCurrentOverflowOutFrames		1.3.6.1.4.1.164.3.1.6.1.2.1.1.20
The number of times the associated ethIfCurrentOutFrames counter has overflowed in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfCurrentOverflowOutOctets		1.3.6.1.4.1.164.3.1.6.1.2.1.1.21
The number of times the associated ethIfCurrentOutOctets counter has overflowed in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfCurrentOverflowMultipleCollisionFrames		1.3.6.1.4.1.164.3.1.6.1.2.1.1.22
The number of times the associated ethIfCurrentMultipleCollisionFrames counter has overflowed in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfCurrentInUnicastFrames		1.3.6.1.4.1.164.3.1.6.1.2.1.1.23
The number of received Unicast frames, encountered by the Ethernet interface in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfCurrentOutUnicastFrames		1.3.6.1.4.1.164.3.1.6.1.2.1.1.24
The number of transmitted Unicast frames, encountered by the Ethernet interface in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfCurrentInMulticastFrames		1.3.6.1.4.1.164.3.1.6.1.2.1.1.25
The number of received Multicast frames, encountered by the Ethernet interface in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfCurrentOutMulticastFrames		1.3.6.1.4.1.164.3.1.6.1.2.1.1.26
The number of transmitted Multicast frames, encountered by the Ethernet interface in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfCurrentInBroadcastFrames		1.3.6.1.4.1.164.3.1.6.1.2.1.1.27
The number of received Broadcast frames, encountered by the Ethernet interface in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfCurrentOutBroadcastFrames		1.3.6.1.4.1.164.3.1.6.1.2.1.1.28
The number of transmitted Broadcast frames, encountered by the Ethernet interface in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfCurrentInDiscardFrames		1.3.6.1.4.1.164.3.1.6.1.2.1.1.29
The number of received Discarded frames, encountered by the Ethernet interface in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfCurrentOutDiscardFrames		1.3.6.1.4.1.164.3.1.6.1.2.1.1.30
The number of transmitted Discarded frames, encountered by the Ethernet interface in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfCurrentInPauseFrames		1.3.6.1.4.1.164.3.1.6.1.2.1.1.31
The number of received Pause frames, encountered by the Ethernet interface in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfCurrentOutPauseFrames		1.3.6.1.4.1.164.3.1.6.1.2.1.1.32
The number of transmitted Pause frames, encountered by the Ethernet interface in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfCurrentOverflowInUnicastFrames		1.3.6.1.4.1.164.3.1.6.1.2.1.1.33
The number of times the associated ethIfCurrentInUnicastFrames counter has overflowed in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfCurrentOverflowOutUnicastFrames		1.3.6.1.4.1.164.3.1.6.1.2.1.1.34
The number of times the associated ethIfCurrentOutUnicastFrames counter has overflowed in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfCurrentOverflowInMulticastFrames		1.3.6.1.4.1.164.3.1.6.1.2.1.1.35
The number of times the associated ethIfCurrentInMulticastFrames counter has overflowed in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfCurrentOverflowOutMulticastFrames		1.3.6.1.4.1.164.3.1.6.1.2.1.1.36
The number of times the associated ethIfCurrentOutMulticastFrames counter has overflowed in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfCurrentOverflowInBroadcastFrames		1.3.6.1.4.1.164.3.1.6.1.2.1.1.37
The number of times the associated ethIfCurrentInBroadcastFrames counter has overflowed in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfCurrentOverflowOutBroadcastFrames		1.3.6.1.4.1.164.3.1.6.1.2.1.1.38
The number of times the associated ethIfCurrentOutBroadcastFrames counter has overflowed in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfCurrentOverflowInDiscardFrames		1.3.6.1.4.1.164.3.1.6.1.2.1.1.39
The number of times the associated ethIfCurrentInDiscardFrames counter has overflowed in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfCurrentOverflowOutDiscardFrames		1.3.6.1.4.1.164.3.1.6.1.2.1.1.40
The number of times the associated ethIfCurrentOutDiscardFrames counter has overflowed in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfCurrentOverflowInPauseFrames		1.3.6.1.4.1.164.3.1.6.1.2.1.1.41
The number of times the associated ethIfCurrentInPauseFrames counter has overflowed in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfCurrentOverflowOutPauseFrames		1.3.6.1.4.1.164.3.1.6.1.2.1.1.42
The number of times the associated ethIfCurrentOutPauseFrames counter has overflowed in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfIntervalTable		1.3.6.1.4.1.164.3.1.6.1.2.2
The Ethernet Interval table. When ethIfIntervalIndex specifies the Ethernet interface (only), the counters are for an interval of 15 minutes.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EthIfIntervalEntry

ethIfIntervalEntry		1.3.6.1.4.1.164.3.1.6.1.2.2.1
An entry in the Ethernet Interval table.
Status: current	Access: not-accessible
OBJECT-TYPE
	EthIfIntervalEntry

ethIfIntervalIndex		1.3.6.1.4.1.164.3.1.6.1.2.2.1.1
The index of the Ethernet interface. It may be ifIndex. For some devices (e.g RICi-622GE), supporting several types of intervals, this index will be a concatenation of the port index and interval type. Interval type can indicate: 1 minute, 15 minutes, 1 hour, 24 hours. For the exact formula, see device specification.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ethIfIntervalNumber		1.3.6.1.4.1.164.3.1.6.1.2.2.1.2
The Interval Number. This number is between 1 and x, where 1 is the most recently completed interval and x is the least recently completed interval. For 15 minute intervals, usually x=96, but it can be different, depending on device capabilities.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..200

ethIfIntervalStatus		1.3.6.1.4.1.164.3.1.6.1.2.2.1.3
The status of the interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was partialy out. 4 - notValid - module is out.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(4)

ethIfIntervalInFrames		1.3.6.1.4.1.164.3.1.6.1.2.2.1.4
The counter associated with the number of received frames, encountered by the Ethernet interface in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfIntervalInOctets		1.3.6.1.4.1.164.3.1.6.1.2.2.1.5
The counter associated with the number of received octets, encountered by the Ethernet interface in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfIntervalAlignmentErrors		1.3.6.1.4.1.164.3.1.6.1.2.2.1.6
The counter associated with the number of received frames, which are not complete (The result of dividing the number of bits by 8 is not an Integer), encountered by the Ethernet interface in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfIntervalFCSErrors		1.3.6.1.4.1.164.3.1.6.1.2.2.1.7
The counter associated with the number of received frames that didn't pass the FCS test, encountered by the Ethernet interface in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfIntervalLengthError		1.3.6.1.4.1.164.3.1.6.1.2.2.1.8
The counter associated with the number of received frames with length error, encountered by the Ethernet interface in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfIntervalOutFrames		1.3.6.1.4.1.164.3.1.6.1.2.2.1.9
The counter associated with the number of transmitted frames, encountered by the Ethernet interface in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfIntervalOutOctets		1.3.6.1.4.1.164.3.1.6.1.2.2.1.10
The counter associated with the number of transmitted octets, encountered by the Ethernet interface in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfIntervalSingleCollisionFrames		1.3.6.1.4.1.164.3.1.6.1.2.2.1.11
The counter associated with the number of successfully transmitted frames for which transmission was inhibited by exactly one collision, encountered by the Ethernet interface in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfIntervalMultipleCollisionFrames		1.3.6.1.4.1.164.3.1.6.1.2.2.1.12
The counter associated with the number of successfully transmitted frames for which transmission was inhibited by more than one collision, encountered by the Ethernet interface in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfIntervalDeferredTransmissions		1.3.6.1.4.1.164.3.1.6.1.2.2.1.13
The counter associated with the number of transmitted frames for which the first transmission attempt was delayed due to a busy media, encountered by the Ethernet interface in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfIntervalLateCollisions		1.3.6.1.4.1.164.3.1.6.1.2.2.1.14
The counter associated with the number of times that a collision was detected later than the first 64 bytes of the frame, encountered by the Ethernet interface in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfIntervalCarrierSenseErrors		1.3.6.1.4.1.164.3.1.6.1.2.2.1.15
The counter associated with the number of times that the carrier sense condition was lost or never asserted when attempting to transmit a frame, encountered by the Ethernet interface in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfIntervalInputCongestionDropped		1.3.6.1.4.1.164.3.1.6.1.2.2.1.16
The counter associated with the number of dropped frames due to a congestion, encountered by the Receive direction to the Ethernet interface in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfIntervalOutputCongestionDropped		1.3.6.1.4.1.164.3.1.6.1.2.2.1.17
The counter associated with the number of dropped frames due to a congestion, encountered by the Transmit direction to the Ethernet interface in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfIntervalOverflowInFrames		1.3.6.1.4.1.164.3.1.6.1.2.2.1.18
The number of times the associated ethIfIntervalInFrames counter has overflowed in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfIntervalOverflowInOctets		1.3.6.1.4.1.164.3.1.6.1.2.2.1.19
The number of times the associated ethIfIntervalInOctets counter has overflowed in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfIntervalOverflowFCSErrors		1.3.6.1.4.1.164.3.1.6.1.2.2.1.20
The number of times the associated ethIfIntervalFCSErrors counter has overflowed in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfIntervalOverflowOutFrames		1.3.6.1.4.1.164.3.1.6.1.2.2.1.21
The number of times the associated ethIfIntervalOutFrames counter has overflowed in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfIntervalOverflowOutOctets		1.3.6.1.4.1.164.3.1.6.1.2.2.1.22
The number of times the associated ethIfIntervalOutOctets counter has overflowed in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfIntervalOverflowMultipleCollisionFrames		1.3.6.1.4.1.164.3.1.6.1.2.2.1.23
The number of times the associated ethIfIntervalMultipleCollisionFrames counter has overflowed in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfIntervalInUnicastFrames		1.3.6.1.4.1.164.3.1.6.1.2.2.1.24
The number of received Unicast frames, encountered by the Ethernet interface in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfIntervalOutUnicastFrames		1.3.6.1.4.1.164.3.1.6.1.2.2.1.25
The number of transmitted Unicast frames, encountered by the Ethernet interface in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfIntervalInMulticastFrames		1.3.6.1.4.1.164.3.1.6.1.2.2.1.26
The number of received Multicast frames, encountered by the Ethernet interface in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfIntervalOutMulticastFrames		1.3.6.1.4.1.164.3.1.6.1.2.2.1.27
The number of transmitted Multicast frames, encountered by the Ethernet interface in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfIntervalInBroadcastFrames		1.3.6.1.4.1.164.3.1.6.1.2.2.1.28
The number of received Broadcast frames, encountered by the Ethernet interface in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfIntervalOutBroadcastFrames		1.3.6.1.4.1.164.3.1.6.1.2.2.1.29
The number of transmitted Broadcast frames, encountered by the Ethernet interface in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfIntervalInDiscardFrames		1.3.6.1.4.1.164.3.1.6.1.2.2.1.30
The number of received Discarded frames, encountered by the Ethernet interface in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfIntervalOutDiscardFrames		1.3.6.1.4.1.164.3.1.6.1.2.2.1.31
The number of transmitted Discarded frames, encountered by the Ethernet interface in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfIntervalInPauseFrames		1.3.6.1.4.1.164.3.1.6.1.2.2.1.32
The number of received Pause frames, encountered by the Ethernet interface in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfIntervalOutPauseFrames		1.3.6.1.4.1.164.3.1.6.1.2.2.1.33
The number of transmitted Pause frames, encountered by the Ethernet interface in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfIntervalOverflowInUnicastFrames		1.3.6.1.4.1.164.3.1.6.1.2.2.1.34
The number of times the associated ethIfIntervalInUnicastFrames counter has overflowed in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfIntervalOverflowOutUnicastFrames		1.3.6.1.4.1.164.3.1.6.1.2.2.1.35
The number of times the associated ethIfIntervalOutUnicastFrames counter has overflowed in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfIntervalOverflowInMulticastFrames		1.3.6.1.4.1.164.3.1.6.1.2.2.1.36
The number of times the associated ethIfIntervalInMulticastFrames counter has overflowed in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfIntervalOverflowOutMulticastFrames		1.3.6.1.4.1.164.3.1.6.1.2.2.1.37
The number of times the associated ethIfIntervalOutMulticastFrames counter has overflowed in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfIntervalOverflowInBroadcastFrames		1.3.6.1.4.1.164.3.1.6.1.2.2.1.38
The number of times the associated ethIfIntervalInBroadcastFrames counter has overflowed in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfIntervalOverflowOutBroadcastFrames		1.3.6.1.4.1.164.3.1.6.1.2.2.1.39
The number of times the associated ethIfIntervalOutBroadcastFrames counter has overflowed in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfIntervalOverflowInDiscardFrames		1.3.6.1.4.1.164.3.1.6.1.2.2.1.40
The number of times the associated ethIfIntervalInDiscardFrames counter has overflowed in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfIntervalOverflowOutDiscardFrames		1.3.6.1.4.1.164.3.1.6.1.2.2.1.41
The number of times the associated ethIfIntervalOutDiscardFrames counter has overflowed in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfIntervalOverflowInPauseFrames		1.3.6.1.4.1.164.3.1.6.1.2.2.1.42
The number of times the associated ethIfIntervalInPauseFrames counter has overflowed in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfIntervalOverflowOutPauseFrames		1.3.6.1.4.1.164.3.1.6.1.2.2.1.43
The number of times the associated ethIfIntervalOutPauseFrames counter has overflowed in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethPerformanceMode		1.3.6.1.4.1.164.3.1.6.1.2.3
This object indicates whether OK or Fail statistics will be counted.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notApplicable(1), countOK(2), countFail(3)

ethIfPerfTable		1.3.6.1.4.1.164.3.1.6.1.2.4
The Ethernet Performance table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EthIfPerfEntry

ethIfPerfEntry		1.3.6.1.4.1.164.3.1.6.1.2.4.1
An entry in the Ethernet Performance table.
Status: current	Access: not-accessible
OBJECT-TYPE
	EthIfPerfEntry

ethIfPerfInOkFrames		1.3.6.1.4.1.164.3.1.6.1.2.4.1.1
The counter associated with the number of received OK frames, encountered by the Ethernet interface since ethPerformanceMode Set to countOK (2) or Reset Statistics was done.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfPerfOutOkFrames		1.3.6.1.4.1.164.3.1.6.1.2.4.1.2
The counter associated with the number of transmitted OK frames, encountered by the Ethernet interface since ethPerformanceMode Set to countOK (2) or Reset Statistics was done.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfPerfTotalCollisions		1.3.6.1.4.1.164.3.1.6.1.2.4.1.3
The counter associated with the total number of collisions of any type encountered by the Ethernet interface since ethPerformanceMode Set to countOK (2) or Reset Statistics was done
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfPerfInOkOctets		1.3.6.1.4.1.164.3.1.6.1.2.4.1.4
The counter associated with the number of received OK Octets, encountered by the Ethernet interface since ethPerformanceMode Set to countOK (2) or Reset Statistics was done.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ethIfOamCfm		1.3.6.1.4.1.164.3.1.6.1.3
OBJECT IDENTIFIER

ethIfOamCfmEvents		1.3.6.1.4.1.164.3.1.6.1.3.0
OBJECT IDENTIFIER

ethOamCfmDefectCondition		1.3.6.1.4.1.164.3.1.6.1.3.0.1
This trap indicates that a MEP has a persistent defect condition.
Status: current	Access: read-only
NOTIFICATION-TYPE

radMepTable		1.3.6.1.4.1.164.3.1.6.1.3.1
MEG End Point (MEP) configuration table associated with Maitenance Entity Group (MEG) End Point. MEP is a short name for an expanded ETH flow point that includes a compound ETH Segment flow termination function, which marks the end point of an ETH ME, and a compound ETH Diagnostic flow function.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RadMepEntry

radMepEntry		1.3.6.1.4.1.164.3.1.6.1.3.1.1
An entry in the table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RadMepEntry

radOamIdx1		1.3.6.1.4.1.164.3.1.6.1.3.1.1.1
This object may indicate the Bridge Index or Configuration index.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

radOamEvcIdx		1.3.6.1.4.1.164.3.1.6.1.3.1.1.2
This object indicates the Index of the EVC (Ethernet Virtual Circuit) that the MEP is associated to.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

radMepIdx		1.3.6.1.4.1.164.3.1.6.1.3.1.1.3
This object indicates the ID of the MEP being accessed.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

radMepRowStatus		1.3.6.1.4.1.164.3.1.6.1.3.1.1.4
This attribute allows to create/delete a row in this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

radMepLocalMepId		1.3.6.1.4.1.164.3.1.6.1.3.1.1.5
This object indicates the local MEP ID.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

radMepRemoteMepId		1.3.6.1.4.1.164.3.1.6.1.3.1.1.6
This atribute is currently implemneted at radMepCcTable, that supports multicast.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

radMepOamMode		1.3.6.1.4.1.164.3.1.6.1.3.1.1.7
This object determines the OAM mode of the MEP: disabled - no CC is initiated nor responded initiate - the device initiates and responds to CC react - the device does not initiate a CC, but responds to CC.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disabled(2), initiate(3), react(4)

radMepContinuityVerMode		1.3.6.1.4.1.164.3.1.6.1.3.1.1.8
This object determines the OAM behavior of the MEP: disabled - no CC is done cc_based - CC is done based on incoming messages lb_based - CC is done based on loopback messages.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disabled(2), ccBased(3), lbBased(4)

radMepMeLevel		1.3.6.1.4.1.164.3.1.6.1.3.1.1.9
At any point in a network, ME Level is used to distinguish between OAM signals belonging to different nested MEs. Maintenance Entity Levels are defined as follows: 0,1,2 are assigned to customers 3,4 are assigned to providers 5,6,7 are assigned to operators.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..7

radMepOamDestAddrType		1.3.6.1.4.1.164.3.1.6.1.3.1.1.10
This object determines if the OAM messages are sent to user defined unicast address, or to RAD proprietary multicast address.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	unicast(1), multicast(2)

radMepOamDestMacAddr		1.3.6.1.4.1.164.3.1.6.1.3.1.1.11
This object determines the MAC address that OAM packets are sent to.
Status: current	Access: read-create
OBJECT-TYPE
	MacAddress

radMepDefaultPriority		1.3.6.1.4.1.164.3.1.6.1.3.1.1.12
This object defines the priority of the OAM messages sent when no service is defined on EVC. If a service is defined, the OAM messages will get the highest service priority existing on the EVC.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..7

radMepCcStatus		1.3.6.1.4.1.164.3.1.6.1.3.1.1.13
This object indicates the Continuity Check (CC) status.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), fail(2), ok(3), mismerge(4), unexpectedMep(5), unexpectedMeLevel(6)

radMepOamProtocol		1.3.6.1.4.1.164.3.1.6.1.3.1.1.14
Determines whether to use proprietary OAM mechanism, or to use the standard (IEEE 802.1ag, ITU-T Y.1731).
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	proprietary(1), standard(2)

radMepMdId		1.3.6.1.4.1.164.3.1.6.1.3.1.1.15
The index of the Maintenance Domain in the radMdTable (radMdIndex).
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

radMepMaFormat		1.3.6.1.4.1.164.3.1.6.1.3.1.1.16
The type (and thereby format) of the Maintenance Association Name.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	primaryVid(1), charString(2), unsignedInt16(3), rfc2865VpnId(4), icc(32)

radMepMaName		1.3.6.1.4.1.164.3.1.6.1.3.1.1.17
The Short Maintenance Association name.
Status: current	Access: read-create
OBJECT-TYPE
	OCTET STRING	Size(1..45)

radMepSpVlanId		1.3.6.1.4.1.164.3.1.6.1.3.1.1.18
The SP (Service Provider) VLAN used when sending an OAM message.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

radMepCcInterval		1.3.6.1.4.1.164.3.1.6.1.3.1.1.19
Indicates the interval at which CCMs are sent by a MEP Valid only if radMepOamMode = initiate(4).
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	intervalInvalid(0), interval300Hz(1), interval10ms(2), interval100ms(3), interval1s(4), interval10s(5), interval1min(6), interval10min(7)

radMepTransmitLbmDestMacAddress		1.3.6.1.4.1.164.3.1.6.1.3.1.1.20
The Target MAC Address Field to be transmitted in the Loopback Message: For unicast MAC Address this is the unicast destination MAC address. For multicast MAC Address, this variable is read-only. This address will be used if the value of radMepTransmitLbmDestIsMepId is no (2). 802.1ag clause 12.14.7.3.2:b.
Status: current	Access: read-create
OBJECT-TYPE
	MacAddress

radMepTransmitLbmDestMepId		1.3.6.1.4.1.164.3.1.6.1.3.1.1.21
The MEPID of another MEP in the same MA to which the LBM is to be sent. This address will be used if the value of radMepTransmitLbmDestIsMepId is yes (3). 802.1ag clause 12.14.7.3.2:b.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

radMepTransmitLbmDestIsMepId		1.3.6.1.4.1.164.3.1.6.1.3.1.1.22
yes (3) indicates that MEPID of the target MEP is used for loopback transmission. no (2) indicates that unicast destination MAC address of the target MEP is used. 802.1ag clause 12.14.7.3.2:b.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	no(2), yes(3)

radMepTransmitLbmMassages		1.3.6.1.4.1.164.3.1.6.1.3.1.1.23
The number of Loopback messages to be transmitted.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..1024

radMepTransmitLbmVlanPriority		1.3.6.1.4.1.164.3.1.6.1.3.1.1.24
The priority to be used in the VLAN tag, if present, in the transmitted frame. The default value is CCM priority. 802.1ag clause 12.14.7.3.2:e
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..7

radMepTransmitLbmVlanDropEnable		1.3.6.1.4.1.164.3.1.6.1.3.1.1.25
Drop Enable bit to be used in the VLAN tag, if present, in the transmitted frame. 802.1ag clause 12.14.7.3.2:e
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	no(2), yes(3)

radMepLbrIn		1.3.6.1.4.1.164.3.1.6.1.3.1.1.26
Total number of valid, in-order Loopback Replies received.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

radMepLbrInOutOfOrder		1.3.6.1.4.1.164.3.1.6.1.3.1.1.27
The total number of valid, out-of-order Loopback Replies received.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

radMepLbmOut		1.3.6.1.4.1.164.3.1.6.1.3.1.1.28
Total number of Loopback Messages transmitted.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

radMepTransmitLtmTargetMacAddress		1.3.6.1.4.1.164.3.1.6.1.3.1.1.29
The Target MAC Address Field to be transmitted in the Link Trace Message: A unicast destination MAC address. This address will be used if the value of radMepTransmitLtmTargetIsMepId is no (2). 802.1ag clause 12.14.7.4.2:c.
Status: current	Access: read-create
OBJECT-TYPE
	MacAddress

radMepTransmitLtmTargetMepId		1.3.6.1.4.1.164.3.1.6.1.3.1.1.30
The MEPID of another MEP in the same MA to which LTM is to be transmitted. This address will be used if the value of radMepTransmitLtmTargetIsMepId is yes (3). 802.1ag clause 12.14.7.4.2:c.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

radMepTransmitLtmTargetIsMepId		1.3.6.1.4.1.164.3.1.6.1.3.1.1.31
yes (3) indicates that MEPID of the target MEP is used for Linktrace transmission. no (2) indicates that unicast destination MAC address of the target MEP is used. 802.1ag clause 12.14.7.4.2:c.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	no(2), yes(3)

radMepTransmitLtmTtl		1.3.6.1.4.1.164.3.1.6.1.3.1.1.32
The LTM TTL field. Default value, if not specified, is 64. The TTL field indicates the number of hops remaining to the LTM. Decremented by 1 each Linktrace Responder that handles the LTM. The value received in the LTM is returned in the LTR. If 0 on input, the LTM is not transmitted to the next hop. 802.1ag clause 12.14.7.4.2:b and 21.8.4.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

radMepTransmitLtmActivationCmd		1.3.6.1.4.1.164.3.1.6.1.3.1.1.33
Activation command for starting Loop Trace. Set will be always to 'on' value. After operation was finished, Agent will turn the value to 'off'.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	off(2), on(3)

ethOamService		1.3.6.1.4.1.164.3.1.6.1.3.2
OBJECT IDENTIFIER

ethOamServiceTable		1.3.6.1.4.1.164.3.1.6.1.3.2.1
Service configuration table associated with Services running on a MEP.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EthOamServiceEntry

ethOamServiceEntry		1.3.6.1.4.1.164.3.1.6.1.3.2.1.1
An entry in the table.
Status: current	Access: not-accessible
OBJECT-TYPE
	EthOamServiceEntry

ethOamServiceIdx		1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.1
This object indicates the Index of the service being accessed.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

ethOamServiceRowStatus		1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.2
This attribute allows to create/delete a row in this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

ethOamServicePriority		1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.3
This object determines the priority of the service. It is sent as P bits in an OAM message originated by this service.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..7

ethOamServicePmEnable		1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.4
This object determines PM (Performance Monitoring) shall be enabled or not for the service.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disable(2), enable(3)

ethOamServiceFrameLossRatioThresh		1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.5
This object determines the Frame Loss ratio threshold in exponent of 1/10. That is, a value of 4 means that the threshold is 1E-4.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	3..10

ethOamServiceDelayThresh		1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.6
This object determines the delay threshold defined for this service, in measurement unit of 0.1 msec.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..50000

ethOamServiceDelayVarThresh		1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.7
This object determines the delay variation threshold defined for this service, in measurement unit of 0.1 msec.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..50000

ethOamServiceUnavailRatioThresh		1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.8
This object determines the Unavailability ratio threshold in exponent of 1/10. That is, a value of 4 means that the threshold is 1E-4.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	3..10

ethOamServiceTxFrames		1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.9
Counts the number of frames trnasmitted by since the time the service is up.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ethOamServiceOverflowTxFrames		1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.10
The number of times the associated ethOamServiceTxFrames counter has overflowed.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ethOamServiceFrameLoss		1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.11
Counts the number of frames lost since the time the service is up.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ethOamServiceOverflowFrameLoss		1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.12
The number of times the associated ethOamServiceFrameLoss counter has overflowed.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ethOamServiceFrameLossRatio		1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.13
Indicates the ratio of the lost frames since the time the service is up. The value is the ratio multiplied by 1E10. 0xFFFFFFFF will be returned for ratio greater than 4/10 (40%).
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

ethOamServiceElapsedTime		1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.14
Indicates the time elapsed in seconds since the time the service is up.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ethOamServiceUnavailSec		1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.15
Indicates the number of unavailable seconds since the time the service is up.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ethOamServiceUnavailRatio		1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.16
Indicates the ratio of the unavailable seconds since the time the service is up. The value is the ratio multiplied by 1E10. 0xFFFFFFFF will be returned for ratio greater than 4/10 (40%).
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

ethOamServiceFramesAboveDelay		1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.17
Indicates the number of frames arrived with delay greater than the delay threshold.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ethOamServiceOverflowFramesAboveDelay		1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.18
Indicates the number of times the associated ethOamServiceFramesAboveDelay counter has overflowed.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ethOamServiceFramesAboveDelayVar		1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.19
Indicates the number of frames arrived with delay variation greater than the delay variation threshold.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ethOamServiceOverflowFramesAboveDelayVar		1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.20
Indicates the number of times the associated ethOamServiceFramesAboveDelayVar counter has overflowed.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ethOamSvcCurrentStatTable		1.3.6.1.4.1.164.3.1.6.1.3.2.2
Service Current Statistics Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EthOamSvcCurrentStatEntry

ethOamSvcCurrentStatEntry		1.3.6.1.4.1.164.3.1.6.1.3.2.2.1
Current Statistics per service
Status: current	Access: not-accessible
OBJECT-TYPE
	EthOamSvcCurrentStatEntry

ethOamSvcCurrFramesAboveDelayThresh		1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.1
Number of frames that arrived in the current interval at a delay greater than the threshold value defined for the service.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCurrentCount

ethOamSvcCurrFramesBelowDelayThresh		1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.2
Number of frames that arrived in the current interval at a delay lower than or equal to the threshold value defined for the service.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCurrentCount

ethOamSvcCurrFramesAboveDVarThresh		1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.3
Number of frames that arrived in the current interval at a delay variation greater than the threshold value defined for the service.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCurrentCount

ethOamSvcCurrFramesBelowDVarThresh		1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.4
Number of frames that arrived in the current interval at a delay variation lower than or equal to the threshold value defined for the service.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCurrentCount

ethOamSvcCurrFramesTxCounter		1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.5
Number of trnasmitted frames in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCurrentCount

ethOamSvcCurrFramesLossCounter		1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.6
Number of lost frames in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCurrentCount

ethOamSvcCurrMinRoundTripDelay		1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.7
The mininal value of round trip delay in the current interval. Values units are of 0.1 msec.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

ethOamSvcCurrMaxRoundTripDelay		1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.8
The maximum value of round trip delay in the current interval. Values units are of 0.1 msec.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

ethOamSvcCurrAvgRoundTripDelay		1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.9
The average round trip delay in the current interval. Values units are of 0.1 msec.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

ethOamSvcCurrMaxRoundTripDVar		1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.10
The maximum value of round trip delay variation in the current interval. Values units are of 0.1 msec.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

ethOamSvcCurrAvgRoundTripDVar		1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.11
The average round trip delay variation in the current interval. Values units are of 0.1 msec.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

ethOamSvcCurrElapsedTime		1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.12
The number of seconds that have elapsed since the beginning of the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..899

ethOamSvcCurrUnavailSec		1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.13
The number of seconds that the service was unavailable in the current interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCurrentCount

ethOamSvcIntervalTable		1.3.6.1.4.1.164.3.1.6.1.3.2.3
Service Interval Statistics Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EthOamSvcIntervalEntry

ethOamSvcIntervalEntry		1.3.6.1.4.1.164.3.1.6.1.3.2.3.1
Interval Statistics per service
Status: current	Access: not-accessible
OBJECT-TYPE
	EthOamSvcIntervalEntry

ethOamSvcIntervalNum		1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.1
The Interval index, which is actualy the Interval number, where 1 is the most recently completed 15 minute interval, and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals exist).
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..96

ethOamSvcIntervalFramesAboveDelayThresh		1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.2
Number of frames that arrived in a delay greater than the threshold value defined for the service in the selected interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfIntervalCount

ethOamSvcIntervalFramesBelowDelayThresh		1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.3
Number of frames that arrived in a delay lower than the threshold value defined for the service in the selected interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfIntervalCount

ethOamSvcIntervalFramesAboveDVarThresh		1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.4
Number of frames that arrived in a delay variation greater than the threshold value defined for the service in the selected interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfIntervalCount

ethOamSvcIntervalFramesBelowDVarThresh		1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.5
Number of frames that arrived in a delay variation lower than the threshold value defined for the service in the selected interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfIntervalCount

ethOamSvcIntervalFramesTxCounter		1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.6
Number of trnasmitted frames in the selected interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfIntervalCount

ethOamSvcIntervalFramesLossCounter		1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.7
Number of lost frames in the selected interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfIntervalCount

ethOamSvcIntervalMinRoundTripDelay		1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.8
The mininal value of round trip delay in the selected interval. Values units are of 0.1 msec.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

ethOamSvcIntervalMaxRoundTripDelay		1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.9
The maximum value of round trip delay in the selected interval. Values units are of 0.1 msec.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

ethOamSvcIntervalAvgRoundTripDelay		1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.10
The average round trip delay in the selected interval. Values units are of 0.1 msec.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

ethOamSvcIntervalMaxRoundTripDVar		1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.11
The maximum value of round trip delay variation in the selected interval. Values units are of 0.1 msec.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

ethOamSvcIntervalAvgRoundTripDVar		1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.12
The average round trip delay variation in the selected interval. Values units are of 0.1 msec.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

ethOamSvcIntervalUnavailSec		1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.13
The number of seconds that the service was unavailable in the selected interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfIntervalCount

ethOamSvcTotalTable		1.3.6.1.4.1.164.3.1.6.1.3.2.4
ETH OAM Service Total (24H) Statistics Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EthOamSvcTotalEntry

ethOamSvcTotalEntry		1.3.6.1.4.1.164.3.1.6.1.3.2.4.1
Total Statistics per service
Status: current	Access: not-accessible
OBJECT-TYPE
	EthOamSvcTotalEntry

ethOamSvcTotalFramesAboveDelayThresh		1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.1
Number of frames that arrived in a delay greater than the threshold value defined for the service in the last 24H.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

ethOamSvcTotalFramesBelowDelayThresh		1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.2
Number of frames that arrived in a delay lower than the threshold value defined for the service in the last 24H.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

ethOamSvcTotalFramesAboveDVarThresh		1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.3
Number of frames that arrived in a delay variation greater than the threshold value defined for the service in the last 24H.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

ethOamSvcTotalFramesBelowDVarThresh		1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.4
Number of frames that arrived in a delay variation lower than the threshold value defined for the service in the last 24H.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

ethOamSvcTotalFramesTxCounter		1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.5
Number of trnasmitted frames in the last 24H.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

ethOamSvcTotalFramesLossCounter		1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.6
Number of lost frames in the last 24H.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

ethOamSvcTotalMinRoundTripDelay		1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.7
The mininal value of round trip delay in the last 24H. Values units are of 0.1 msec.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

ethOamSvcTotalMaxRoundTripDelay		1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.8
The maximum value of round trip delay in the last 24H. Values units are of 0.1 msec.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

ethOamSvcTotalAvgRoundTripDelay		1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.9
The average round trip delay in the last 24H. Values units are of 0.1 msec.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

ethOamSvcTotalMaxRoundTripDVar		1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.10
The maximum value of round trip delay variation in the last 24H. Values units are of 0.1 msec.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

ethOamSvcTotalAvgRoundTripDVar		1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.11
The average round trip delay variation in the last 24H. Values units are of 0.1 msec.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

ethOamSvcTotalUnavailSec		1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.12
The number of seconds that the service was unavailable in the last 24H.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

radMdTable		1.3.6.1.4.1.164.3.1.6.1.3.3
The MaintenanceDomain table. Each row in the table represents a different maintenance domain. A Maintenance domain is described in 802.1ag (3.22) as the network or the part of the network for which faults in connectivity are to be managed. The boundary of a Maintenance Domain is defined by a set of DSAPs, each of which can become a point of connectivity to a service instance.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RadMdEntry

radMdEntry		1.3.6.1.4.1.164.3.1.6.1.3.3.1
The Maintenance Domain table entry. This entry is not lost upon reboot. It is backed up by stable storage
Status: current	Access: not-accessible
OBJECT-TYPE
	RadMdEntry

radMdIndex		1.3.6.1.4.1.164.3.1.6.1.3.3.1.1
The index to the maintenance domain table.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

radMdFormat		1.3.6.1.4.1.164.3.1.6.1.3.3.1.2
The type (and thereby format) of the Maintenance Domain Name.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	none(1), dnsLikeName(2), macAddressAndUint(3), charString(4)

radMdName		1.3.6.1.4.1.164.3.1.6.1.3.3.1.3
The Maintenance Domain name. The type/format of this object is determined by the value of the radMdNameType object. Each Maintenance Domain has unique name amongst all those used or available to a service provider or operator. It facilitates easy identification of administrative responsibility for each Maintenance Domain.
Status: current	Access: read-create
OBJECT-TYPE
	OCTET STRING	Size(1..43)

radMdRowStatus		1.3.6.1.4.1.164.3.1.6.1.3.3.1.4
This attribute allows to create/delete a row in this table. The writable columns in a row can not be changed if the row is active. All columns must have a valid value before a row can be activated.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

radMepLtrTable		1.3.6.1.4.1.164.3.1.6.1.3.4
This table contains a list of Linktrace replies received by a specific MEP in response to a linktrace message.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RadMepLtrEntry

radMepLtrEntry		1.3.6.1.4.1.164.3.1.6.1.3.4.1
The LinktraceReply table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RadMepLtrEntry

radMepLtrReceiveOrder		1.3.6.1.4.1.164.3.1.6.1.3.4.1.1
An index to distinguish among multiple LTRs with the same LTR Transaction Identifier field value. radMepLtrReceiveOrder are assigned sequentially from 1, in the order that the Linktrace Initiator received the LTRs.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

radMepLtrTtl		1.3.6.1.4.1.164.3.1.6.1.3.4.1.2
TTL field value for a returned LTR.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..255

radMepLtrMacAddr		1.3.6.1.4.1.164.3.1.6.1.3.4.1.3
The MAC address in the header of the returned LTR.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

radMepLtrRelay		1.3.6.1.4.1.164.3.1.6.1.3.4.1.4
The value returned in the Relay Action field: rlyHit - the LTM reached an MP whose MAC address matches the target MAC address. rlyFdb - the Egress Port was determined by consulting the Filtering Database. rlyMpdb - the Egress Port was determined by consulting the MIP CCM Database. 802.1ag clauses 12.14.7.5.3:g and 20.36.2.5
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	rlyHit(1), rlyFdb(2), rlyMpdb(3)

radMepLtrIngress		1.3.6.1.4.1.164.3.1.6.1.3.4.1.5
The value returned in the Ingress Action Field of the LTM. ingNoTlv - no Reply Ingress TLV was returned in the LTM. ingOK - the target data frame would be passed through to the MAC Relay Entity. ingDown - the Bridge Port's MAC_Operational parameter is false. ingBlocked - the target data frame would not be forwarded if received on this port. ingVid - the ingress port is not in the members of the LTM's VID, and ingress filtering is enabled, so the target data frame would be filtered by the ingress filtering. 802.1ag clauses 12.14.7.5.3:k and 20.36.2.6
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ingNoTlv(1), ingOk(2), ingDown(3), ingBlocked(4), ingVid(5)

radMepLtrIngressPortIdSubtype		1.3.6.1.4.1.164.3.1.6.1.3.4.1.6
The format of the Ingress Port ID. If the radMepLtrIngress object contains the value egrNoTlv(1), then the contents of this object are meaningless. 802.1ag clauses 12.14.7.5.3:m and 20.36.2.8
Status: current	Access: read-only
OBJECT-TYPE
	LldpPortIdSubtype

radMepLtrIngressPortId		1.3.6.1.4.1.164.3.1.6.1.3.4.1.7
Ingress Port ID. This is an alpha-numeric string that contains a specific identifier for the port. The format of this object is determined by the value of the radMepLtrIngressPortIdSubtype object. If the radMepLtrIngress object contains the value ingNoTlv(1), then the contents of this object are meaningless. 802.1ag clauses 12.14.7.5.3:n and 20.36.2.9
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(1..255)

radMepLtrEgress		1.3.6.1.4.1.164.3.1.6.1.3.4.1.8
The value returned in the Egress Action Field of the LTM. The value egrNoTlv(1) indicates that no Reply Egress TLV was returned in the LTM. 802.1ag clauses 12.14.7.5.3:o and 20.36.2.10
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	egrNoTlv(1), egrOK(2), egrDown(3), egrBlocked(4), egrVid(5)

radMepLtrEgressPortIdSubtype		1.3.6.1.4.1.164.3.1.6.1.3.4.1.9
The format of the egress Port ID. If the radMepLtrEgress object contains the value egrNoTlv(1), then the contents of this object are meaningless. 802.1ag clauses 12.14.7.5.3:q and 20.36.2.12
Status: current	Access: read-only
OBJECT-TYPE
	LldpPortIdSubtype

radMepLtrEgressPortId		1.3.6.1.4.1.164.3.1.6.1.3.4.1.10
Egress Port ID. The format of this object is determined by the value of the radMepLtrEgressPortIdSubtype object. If the radMepLtrEgress object contains the value egrNoTlv(1), then the contents of this object are meaningless. 802.1ag clauses 12.14.7.5.3:r and 20.36.2.13
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(1..255)

radMepCcStatusTable		1.3.6.1.4.1.164.3.1.6.1.3.5
This table contains a list of CC Status received by a specific MEP from different Remote MEPs.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RadMepCcStatusEntry

radMepCcStatusEntry		1.3.6.1.4.1.164.3.1.6.1.3.5.1
An entry in the CC Status Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	RadMepCcStatusEntry

radMepRemoteMepIdx		1.3.6.1.4.1.164.3.1.6.1.3.5.1.1
This is a running index for arriving CC messages (from different Remote MEPs) for a specific MEP ID.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

radMepCcStatusRemMepId		1.3.6.1.4.1.164.3.1.6.1.3.5.1.2
This attribute indicates the Remote MEP ID from which the CC messages has arrived.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

radMepCcStat		1.3.6.1.4.1.164.3.1.6.1.3.5.1.3
This object indicates the Continuity Check (CC) status (ITU-T Y.1731, Appendix I): mismerge - A MEP detects a Mismerge condition when a CCM frame arrives with the correct MEG level, but incorrect MEG ID. unexpectedMep -A MEP detects an Unexpected MEP condition when a CCM frame arrives with the correct MEG level, the correct MEG ID, but an unexpected MEP ID, which includes the MEP's own MEP ID. unexpectedMeLevel - A MEP detects an Unexpected MEG Level condition when a CCM frame arrives with incorrect MEG Level. Incorrect MEG Level is less than the MEP's own MEG level. unexpectedPeriod - A MEP detects an Unexpected Period condition when a CCM frame arrives with a correct MEG level. a correct MEG ID, a correct MEP ID, but with the Period field value different from the MEP's own CCM transmission period. rdi - A MEP detects RDI when it receives a CCM frame with the RDI field set.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), fail(2), ok(3), mismerge(4), unexpectedMep(5), unexpectedMeLevel(6), unexpectedPeriod(7), rdi(8)

radMepCcStatusMacAddr		1.3.6.1.4.1.164.3.1.6.1.3.5.1.4
This object indicates the MAC Address in the CC Status message received.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

ethOamStdEtherType		1.3.6.1.4.1.164.3.1.6.1.3.6
The Standard Ether Type in an OAM message. This object will be RW until a formal value will be issued for standard Ethernet Type. When such Standard will exist, this object will be supported RO to reflect the Standard value.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

ethOamStdMacAddress		1.3.6.1.4.1.164.3.1.6.1.3.7
The Standard MAC Address in an OAM message. This object will be RW until a formal value will be issued for standard MAC Address. When such Standard will exist, this object will be supported RO to reflect the Standard value.
Status: current	Access: read-write
OBJECT-TYPE
	MacAddress

dot1agXCfmMdTable		1.3.6.1.4.1.164.3.1.6.1.3.8
The Maintenance Domain table. Each row in the table represents a different maintenance association.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Dot1agXCfmMdEntry

dot1agXCfmMdEntry		1.3.6.1.4.1.164.3.1.6.1.3.8.1
The Maintenance Domain table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	Dot1agXCfmMdEntry

dot1agXCfmMdProtocol		1.3.6.1.4.1.164.3.1.6.1.3.8.1.1
.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	preStandard(1), standard(2)

dot1agXCfmMepTable		1.3.6.1.4.1.164.3.1.6.1.3.9
The Maintenance Association End Point (MEP) table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Dot1agXCfmMepEntry

dot1agXCfmMepEntry		1.3.6.1.4.1.164.3.1.6.1.3.9.1
The MEP table entry
Status: current	Access: not-accessible
OBJECT-TYPE
	Dot1agXCfmMepEntry

dot1agXCfmMepContinuityVerMode		1.3.6.1.4.1.164.3.1.6.1.3.9.1.1
This object determines the OAM behavior of the MEP: disabled - no Continuity Verification is done cc_based - Continuity Verification is done based on incoming CC messages lb_based - Continuity Verification is done based on loopback messages.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disabled(2), ccBased(3), lbBased(4)

dot1agXCfmMepDestAddrType		1.3.6.1.4.1.164.3.1.6.1.3.9.1.2
This object determines if the OAM messages are sent to user defined unicast address, or to RAD proprietary multicast address.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	unicast(1), multicast(2)

dot1agXCfmMepDestMacAddr		1.3.6.1.4.1.164.3.1.6.1.3.9.1.3
This object determines the MAC address that OAM packets are sent to.
Status: current	Access: read-create
OBJECT-TYPE
	MacAddress

dot1agXCfmMepDbTable		1.3.6.1.4.1.164.3.1.6.1.3.10
The MEP DB table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Dot1agXCfmMepDbEntry

dot1agXCfmMepDbEntry		1.3.6.1.4.1.164.3.1.6.1.3.10.1
The MEP Database table entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	Dot1agXCfmMepDbEntry

dot1agXCfmMepCcStat		1.3.6.1.4.1.164.3.1.6.1.3.10.1.1
This object indicates the Continuity Check (CC) status (ITU-T Y.1731, Appendix I): mismerge - A MEP detects a Mismerge condition when a CCM frame arrives with the correct MEG level, but incorrect MEG ID. unexpectedMep -A MEP detects an Unexpected MEP condition when a CCM frame arrives with the correct MEG level, the correct MEG ID, but an unexpected MEP ID, which includes the MEP's own MEP ID. unexpectedMeLevel - A MEP detects an Unexpected MEG Level condition when a CCM frame arrives with incorrect MEG Level. Incorrect MEG Level is less than the MEP's own MEG level. unexpectedPeriod - A MEP detects an Unexpected Period condition when a CCM frame arrives with a correct MEG level. a correct MEG ID, a correct MEP ID, but with the Period field value different from the MEP's own CCM transmission period. rdi - A MEP detects RDI when it receives a CCM frame with the RDI field set.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), fail(2), ok(3), mismerge(4), unexpectedMep(5), unexpectedMeLevel(6), unexpectedPeriod(7), rdi(8)

ethIfRing		1.3.6.1.4.1.164.3.1.6.1.4
OBJECT IDENTIFIER

ethIfRingEvents		1.3.6.1.4.1.164.3.1.6.1.4.0
OBJECT IDENTIFIER

ethIfRingTable		1.3.6.1.4.1.164.3.1.6.1.4.1
Ethernet Ring Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EthIfRingEntry

ethIfRingEntry		1.3.6.1.4.1.164.3.1.6.1.4.1.1
An entry in the table.
Status: current	Access: not-accessible
OBJECT-TYPE
	EthIfRingEntry

ethIfRingIdx		1.3.6.1.4.1.164.3.1.6.1.4.1.1.1
This object is an Index that can indicate Slot, Ring, Cnfg etc., according to the device used. When NA, 1 will be used.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

ethIfRingAdminStatus		1.3.6.1.4.1.164.3.1.6.1.4.1.1.2
This object denotes the Ethernet Ring administrative status.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	down(2), up(3)

ethIfRingPorts		1.3.6.1.4.1.164.3.1.6.1.4.1.1.3
The set of ports which are assigned to be ring members. The default value of this object is a string of zeros.
Status: current	Access: read-write
OBJECT-TYPE
	PortList

ethIfRingOperStatus		1.3.6.1.4.1.164.3.1.6.1.4.1.1.4
This object indicates the Ethernet Ring operational status.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notApplicable(1), open(2), close(3)

ethIfRingKeepAliveInterval		1.3.6.1.4.1.164.3.1.6.1.4.1.1.5
This parameter indicates the period of time (in msec.) between two consequent Keep Alive messages.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

ethIfRingKeepAliveThresh		1.3.6.1.4.1.164.3.1.6.1.4.1.1.6
This parameter indicates the maximum number of missed Keep Alive answer messages acceptable, after which link status will be failed.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

ethIfRingKeepAliveVlanId		1.3.6.1.4.1.164.3.1.6.1.4.1.1.7
Dedicated VLAN ID for keep alive messages.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

ethIfRingMultiCastVlanId		1.3.6.1.4.1.164.3.1.6.1.4.1.1.8
Dedicated VLAN ID for multicast messages.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

ethIfRingRowStatus		1.3.6.1.4.1.164.3.1.6.1.4.1.1.9
Implement creation/deletion of rings in the device.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	active(1), createAndGo(4), destroy(6)

ethIfRingStatusChange		1.3.6.1.4.1.164.3.1.6.1.4.0.1
This trap indicates that the status of the Ethernet Ring has been changed.
Status: current	Access: read-write
NOTIFICATION-TYPE

ethIfStorming		1.3.6.1.4.1.164.3.1.6.1.5
OBJECT IDENTIFIER

ethIfStormTable		1.3.6.1.4.1.164.3.1.6.1.5.1
Ethernet Storming Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EthIfStormEntry

ethIfStormEntry		1.3.6.1.4.1.164.3.1.6.1.5.1.1
An entry in the table.
Status: current	Access: not-accessible
OBJECT-TYPE
	EthIfStormEntry

ethIfStormCnfgIdx		1.3.6.1.4.1.164.3.1.6.1.5.1.1.1
This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..255

ethIfStormIfIdx		1.3.6.1.4.1.164.3.1.6.1.5.1.1.2
A unique index of the ethernet interface/port.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

ethIfStormDirection		1.3.6.1.4.1.164.3.1.6.1.5.1.1.3
This object indicates the port's Storm Direction.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	all(1), ingress(2), egress(3)

ethIfStormPacketType		1.3.6.1.4.1.164.3.1.6.1.5.1.1.4
Packet Type on which Storming operations will be performed.
Status: current	Access: not-accessible
OBJECT-TYPE
	BITS	unknownUnicast(0), broadcast(1), multicast(2)

ethIfStormCtrlEnable		1.3.6.1.4.1.164.3.1.6.1.5.1.1.5
This object indicates if the Storm Controling is Enabled or Disabled for the relevant entry.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(2), enable(3)

ethIfStormMaxRate		1.3.6.1.4.1.164.3.1.6.1.5.1.1.6
This object indicates the Maximum Rate at which Storming packets are forwarded, in Kbps.For some devices the units are PPS(Packets Per Second ) or kilobytes per second.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

ethIfOamEfm		1.3.6.1.4.1.164.3.1.6.1.6
OBJECT IDENTIFIER

dot3OamEvents		1.3.6.1.4.1.164.3.1.6.1.6.0
OBJECT IDENTIFIER

dot3OamOperStatusChange		1.3.6.1.4.1.164.3.1.6.1.6.0.1
This trap is sent when OAM EFM Link goes Up or Down. Up - is considered when dot3OamOperStatus value changes to operational(9) from any other value. Down - is considered when dot3OamOperStatus value changes from operational(9) to any other value.
Status: current	Access: read-write
NOTIFICATION-TYPE

dot3OamPeerEvent		1.3.6.1.4.1.164.3.1.6.1.6.0.2
This trap is sent when value of dot3OamXPeerState changes from any value to one of the following values: linkFault, dyingGasp, criticalEvent. This trap has no recovery (clearing value).
Status: current	Access: read-write
NOTIFICATION-TYPE

dot3OamDescrTable		1.3.6.1.4.1.164.3.1.6.1.6.1
This table supports definitions of Descriptors (profiles) of OAM EFM Links.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Dot3OamDescrEntry

dot3OamDescrEntry		1.3.6.1.4.1.164.3.1.6.1.6.1.1
Each entry corresponds to a single OAM EFM Descriptor (profile). Each Descriptor contains a set of OAM EFM Link configuration parameters. The configuration parameters are applied to the OAM EFM Links referencing this Descriptor (see dot3OamXDescrId object). Descriptors may be created/deleted using the row creation/deletion mechanism via dot3OamDescrRowStatus. If an active entry is referenced in dot3OamXDescrId, the entry MUST remain active until all references are removed.
Status: current	Access: not-accessible
OBJECT-TYPE
	Dot3OamDescrEntry

dot3OamDescrId		1.3.6.1.4.1.164.3.1.6.1.6.1.1.1
This object is the unique index associated with this Descriptor (profile). Entries in this table are referenced via the object dot3OamXDescrId in dot3OamXEntry.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..4294967295

dot3OamDescrRowStatus		1.3.6.1.4.1.164.3.1.6.1.6.1.1.2
This object controls creation/deletion of the associated entry in this table per the semantics of RowStatus. If an active entry is referenced in dot3OamXDescrId, the entry MUST remain active until all references are removed.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

dot3OamDescrMode		1.3.6.1.4.1.164.3.1.6.1.6.1.1.3
This object controls the mode of OAM operation for an Ethernet-like interface referencing this Descriptor. OAM on Ethernet interfaces may be in 'active' mode or 'passive' mode. These two modes differ in that active mode provides additional capabilities to initiate monitoring activities with the remote OAM peer entity, while passive mode generally waits for the peer to initiate OAM actions with it. As an example, an active OAM entity can put the remote OAM entity in a loopback state, where a passive OAM entity cannot.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	passive(1), active(2)

dot3OamDescrLbRxOperation		1.3.6.1.4.1.164.3.1.6.1.6.1.1.4
Since OAM loopback is a disruptive operation (user traffic does not pass), this object provides a mechanism to provide control: whether received OAM loopback commands are processed or ignored, for the OAM Link referencing this Descriptor. When the value is ignore(1), received loopback commands are ignored. When the value is process(2), received loopback commands are processed. The default value is to ignore loopback commands (ignore(1)).
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	ignore(1), process(2)

dot3OamDescrRateLimit		1.3.6.1.4.1.164.3.1.6.1.6.1.1.5
This object defines how many OAM frames can be sent per second (maximum) for an OAM EFM Link referencing this Descriptor.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

dot3OamXTable		1.3.6.1.4.1.164.3.1.6.1.6.2
This table is an extension of dot3OamTable of standard DOT3-OAM-MIB.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Dot3OamXEntry

dot3OamXEntry		1.3.6.1.4.1.164.3.1.6.1.6.2.1
An entry in dot3OamXTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	Dot3OamXEntry

dot3OamXDescrId		1.3.6.1.4.1.164.3.1.6.1.6.2.1.1
This object points to an entry of dot3OamDescrTable (dot3OamDescrId), which defines part of the configuration parameters for this OAM EFM Link. As long as one of the OAM EFM Links refers an entry in the dot3OamDescrTable, this entry cannot be removed. When an OAM EFM Link supports this object (RW), the standard MIB objects of: dot3OamMode (parallel to dot3OamDescrMode) and dot3OamLoopbackIgnoreRx (parallel to dot3OamDescrLbRxOperation) will be supported by Agent RO.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	1..4294967295

dot3OamXPeerState		1.3.6.1.4.1.164.3.1.6.1.6.2.1.2
This object reports the state of the Peer of the OAM EFM Link. unknown - at the initialization of the device, or after Reset, when there is still no data about the peer's state. operational - usually after unknown state, when device senses that peer is OK. linkFault - Loss of Signal is detected by the receiver. dyingGasp - Unrecoverable condition has occurred (e.g power failure) criticalEvent - Unspecified Critical Event has occured.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), operational(2), linkFault(3), dyingGasp(4), criticalEvent(5)

ethIfMacLayer		1.3.6.1.4.1.164.3.1.6.1.7
OBJECT IDENTIFIER

ethIfMacLayerEvents		1.3.6.1.4.1.164.3.1.6.1.7.0
OBJECT IDENTIFIER

ethIfSrcMacCtrlTable		1.3.6.1.4.1.164.3.1.6.1.7.1
This table supports source MAC addresses control parameters per interface. Source MAC control will be used mainly for security. Only packets with certain source MAC Addresses will be allowed to access the device. The source MAC addresses can be static or learned. The static addresses will be defined by the user in another table: ethIfSrcMacCtrlAddrTable. The learned addresses will exist in the ethIfSrcMacCtrlAddrTable as well.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EthIfSrcMacCtrlEntry

ethIfSrcMacCtrlEntry		1.3.6.1.4.1.164.3.1.6.1.7.1.1
An entry in the table.
Status: current	Access: not-accessible
OBJECT-TYPE
	EthIfSrcMacCtrlEntry

ethIfSrcMacCtrlIndex		1.3.6.1.4.1.164.3.1.6.1.7.1.1.1
The index of the MAC Layer interface supporting source MAC control feature. It may be the ifIndex of the ETH/Bridge Port.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

ethIfSrcMacCtrlIdx2		1.3.6.1.4.1.164.3.1.6.1.7.1.1.2
A second index that can be used. For example: The VLAN ID for which the source MAC control feature is supported. When this index is not in use, its value will be: 9999.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

ethIfSrcMacCtrl		1.3.6.1.4.1.164.3.1.6.1.7.1.1.3
Enable or disable the source MAC control on the current interface. The device should not enable source MAC control if for the current interface there are more than ethIfSrcMacCtrlMaxPermitAddr addresses in the ethIfSrcMacCtrlAddrTable. Default value will be: disable (2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(2), enable(3)

ethIfSrcMacCtrlMaxPermitAddr		1.3.6.1.4.1.164.3.1.6.1.7.1.1.4
This is the maximum number of permitted MAC addresses (static and learned) for the current interface.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

ethIfSrcMacCtrlCurNumPermitAddr		1.3.6.1.4.1.164.3.1.6.1.7.1.1.5
This is the number of source MAC addresses currently permitted for the current interface.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

ethIfSrcMacCtrlFlushAddrCmd		1.3.6.1.4.1.164.3.1.6.1.7.1.1.6
When set to on (3) this command will erase all the learned addresses and invalid addresses of the selected interface in the ethIfSrcMacCtrlAddrTable. After operation is finished, Agent will turn the value to 'off'.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(2), on(3)

ethIfSrcMacCtrlAging		1.3.6.1.4.1.164.3.1.6.1.7.1.1.7
The timeout period in seconds for aging out dynamically learned source MAC addresses. Valid Values: 0 - disable 10-1000000
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

ethIfSrcMacCtrlLocking		1.3.6.1.4.1.164.3.1.6.1.7.1.1.8
When set to lock (3) this command will lock the Source MAC Address learning. No more learned addresses will be added to the ethIfSrcMacCtrlAddrTable. When set to unlock (2) this command will unlock the Source MAC Address learning. Learned addresses will be added to the ethIfSrcMacCtrlAddrTable but the number of addresses in the table will not exceed ethIfSrcMacCtrlMaxPermitAddr. Default value is: unlock (2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unlock(2), lock(3)

ethIfSrcMacCtrlViolationAction		1.3.6.1.4.1.164.3.1.6.1.7.1.1.9
Determines the action that the device will take upon security violation. drop(2) - the violating packets will be dropped. dropNotify (3)- the violating packets will be dropped and notifications will be generated. Notifications may be for example: SNMP Traps, Syslog messages and log file new entries. shutdown (4) - the interface will be forced to shut down.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	drop(2), dropNotify(3), shutdown(4)

ethIfSrcMacCtrlLastViolatingAddr		1.3.6.1.4.1.164.3.1.6.1.7.1.1.10
This object indicates the last MAC address that violated the security on the current interface. If no violation, the agent will return: 00-00-00-00-00-00 .
Status: current	Access: read-write
OBJECT-TYPE
	MacAddress

ethIfSrcMacCtrlPortStatus		1.3.6.1.4.1.164.3.1.6.1.7.1.1.11
This object represents the operational status of the MAC Control feature on an interface. shutdown(2) - This indicates that the port is shutdown due to security violation. secureActive (3) - This indicates that the MAC Control interface security is operational and this interface is not shutdown due to security violation. secureInactive (4)- This indicates that the MAC Control is not operational.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	shutdown(2), secureActive(3), secureInactive(4)

ethIfSrcMacCtrlAddrTable		1.3.6.1.4.1.164.3.1.6.1.7.2
This table shows which MAC Addresses are permitted when the source MAC control is enabled and which non permitted MAC Addresses attempted to access the current interface. It contains static source MAC Addresses as well as learned MAC Addresses. The user can configure Static permitted source MAC Addresses via this table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EthIfSrcMacCtrlAddrEntry

ethIfSrcMacCtrlAddrEntry		1.3.6.1.4.1.164.3.1.6.1.7.2.1
An entry in the table.
Status: current	Access: not-accessible
OBJECT-TYPE
	EthIfSrcMacCtrlAddrEntry

ethIfSrcMacCtrlAddrIndex		1.3.6.1.4.1.164.3.1.6.1.7.2.1.1
The index of the interface for which the source MAC addresses exist in this table. It may be the ifIndex of the ETH/Bridge Port.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

ethIfSrcMacCtrlAddr		1.3.6.1.4.1.164.3.1.6.1.7.2.1.2
A unicast source MAC address that was learned or statically configured for the current interface. Packets with this source MAC address will be accepted by the device.
Status: current	Access: not-accessible
OBJECT-TYPE
	MacAddress

ethIfSrcMacCtrlAddrIdx3		1.3.6.1.4.1.164.3.1.6.1.7.2.1.3
A third index that can be used. For example: The VLAN ID for which the source MAC control feature is supported. When this index is not in use, its value will be: 9999.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

ethIfSrcMacCtrlAddrRowStatus		1.3.6.1.4.1.164.3.1.6.1.7.2.1.4
This MIB object will be used in order to create/delete a static row or delete an address that is not allowed to access the current interface (ethIfSrcMacCtrlAddrStatus= invalid(2)). Device will add the learned addresses to this table. It will not be possible to add a new static entry to this table while the number of existing rows is equal or more than ethIfSrcMacCtrlMaxPermitAddr. When ethIfSrcMacCtrl = enabled (3), the device will add learned entries only up to ethIfSrcMacCtrlMaxPermitAddr.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	active(1), createAndGo(4), destroy(6)

ethIfSrcMacCtrlAddrStatus		1.3.6.1.4.1.164.3.1.6.1.7.2.1.5
The status of this entry. The meanings of the values are: invalid (2) - the current address is not allowed to access this interface. learned(3) - the current address was learned. mgmt (5) - the current address is static. It may exist in the MAC Table.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	invalid(2), learned(3), mgmt(5)

ethIfMacAccessViolation		1.3.6.1.4.1.164.3.1.6.1.7.0.1
This trap indicates that an Access Violation occurred.
Status: current	Access: read-only
NOTIFICATION-TYPE