QWESCOM-MIB

File: QWESCOM-MIB.mib (141624 bytes)

Imported modules

RFC1155-SMI

RFC-1212

SNMPv2-TC

Imported symbols

Counter	enterprises	IpAddress
TimeTicks	OBJECT-TYPE	RowStatus

Defined Types

DisplayString
OCTET STRING

PhysAddress
OCTET STRING

TimeDateString
INTEGER

Boolean
INTEGER

QsnmpCommunityEntry
SEQUENCE
	qsnmpCommunityIndex	INTEGER
	qsnmpCommunityRights	INTEGER
	qsnmpCommunityName	DisplayString

QsnmpNMSEntry
SEQUENCE
	qsnmpNMSIndex	INTEGER
	qsnmpNMSIpAddress	IpAddress

QsnmpTrapEntry
SEQUENCE
	qsnmpTrapIndex	INTEGER
	qsnmpTrapIpAddress	IpAddress

QClassDefinitionEntry
SEQUENCE
	qClassDefinitionIndex	INTEGER
	qClassDefinitionAlias	DisplayString
	qClassDefinitionParentClassID	INTEGER
	qClassDefinitionFlowType	INTEGER
	qClassDefinitionSourceIPMask	OCTET STRING
	qClassDefinitionDestIPMask	IpAddress
	qClassDefinitionSourceIPLowerBound	IpAddress
	qClassDefinitionSourceIPUpperBound	IpAddress
	qClassDefinitionDestIPLowerBound	IpAddress
	qClassDefinitionDestIPUpperBound	IpAddress
	qClassDefinitionDSMask	INTEGER
	qClassDefinitionDSLowerBound	INTEGER
	qClassDefinitionDSUpperBound	INTEGER
	qClassDefinitionWellKnownApplication	INTEGER
	qClassDefinitionProtocol	INTEGER
	qClassDefinitionSourcePortLowerBound	INTEGER
	qClassDefinitionSourcePortUpperBound	INTEGER
	qClassDefinitionDestPortLowerBound	INTEGER
	qClassDefinitionDestPortUpperBound	INTEGER
	qClassDefinitionFlowAgingTime	INTEGER

QPolicyDefinitionEntry
SEQUENCE
	qPolicyDefinitionIndex	INTEGER
	qPolicyDefinitionAlias	DisplayString
	qPolicyDefinitionType	INTEGER
	qPolicyDefinitionLP	INTEGER
	qPolicyDefinitionStartTime	TimeDateString
	qPolicyDefinitionEndTime	TimeDateString
	qPolicyDefinitionDayofWeek	INTEGER
	qPolicyDefinitionPipeID	INTEGER
	qPolicyDefinitionClassID	INTEGER
	qPolicyDefinitionChannelized	INTEGER
	qPolicyDefinitionOutboundDSValue	INTEGER
	qPolicyDefinitionPriority	INTEGER
	qPolicyDefinitionEvent	INTEGER

QPipeDefinitionEntry
SEQUENCE
	qPipeDefinitionIndex	INTEGER
	qPipeDefinitionAlias	DisplayString
	qPipeDefinitionType	INTEGER
	qPipeDefinitionCircuitID	INTEGER
	qPipeDefinitionBandwidth	INTEGER
	qPipeDefinitionPeak	INTEGER
	qPipeDefinitionMBS	INTEGER
	qPipeDefinitionBufferAllocation	INTEGER
	qPipeDefinitionDelay	INTEGER
	qPipeDefinitionPhyIdx	INTEGER
	qPipeDefinitionPhyType	INTEGER

QClassStatisticsEntry
SEQUENCE
	qClassStatisticsIndex	INTEGER
	qClassStatisticsAlias	DisplayString
	qClassStatisticsTransmittedCount	Counter
	qClassStatisticsDiscardCount	Counter
	qClassStatisticsFallbackCount	Counter

QatmCircuitEntry
SEQUENCE
	qatmCircuitId	INTEGER
	qatmCircuitAlias	DisplayString
	qatmCircuitUNI	INTEGER
	qatmCircuitLogicalInterface	INTEGER
	qatmCircuitVpi	INTEGER
	qatmCircuitFirstVci	INTEGER
	qatmCircuitMode	INTEGER
	qatmCircuitStatus	INTEGER

QatmUniEntry
SEQUENCE
	qatmSpanPort	INTEGER
	qatmUniName	DisplayString
	qatmUniAlias	DisplayString
	qatmUniTrapStatus	INTEGER
	qatmUniMaxQueueDelay	INTEGER
	qatmUniMinAllocBuffer	INTEGER
	qatmUniSharedBuffer	INTEGER
	qatmUniLinkBandwidth	INTEGER
	qatmUniLinkDelay	INTEGER
	qatmUniBandwidthGranularity	INTEGER
	qatmUniIlmiStatus	INTEGER
	qatmUniRowStatus	INTEGER

QatmVplEntry
SEQUENCE
	qatmVplMaxVcc	INTEGER
	qatmVplLowestVci	INTEGER
	qatmVplMaxQueueDelay	INTEGER
	qatmVplReservedBuffer	INTEGER
	qatmVplBwGranularity	INTEGER
	qatmVplMtu	INTEGER
	qatmVplSharedBuffer	INTEGER

QatmVclEntry
SEQUENCE
	qatmVclBwGranularity	INTEGER
	qatmVclMaxSubChannels	INTEGER
	qatmVclMaxQueueDelay	INTEGER
	qatmVclReservedBuffer	INTEGER
	qatmVclSharedBuffer	INTEGER

QatmAal5Entry
SEQUENCE
	qatmAal5Uni	INTEGER
	qatmAal5Aal5Name	DisplayString
	qatmAal5Aal5Alias	DisplayString
	qatmAal5AdminStatus	INTEGER
	qatmAal5TrapStatus	INTEGER
	qatmAal5MtuSize	INTEGER
	qatmAal5RowStatus	INTEGER

QatmTrafficDescriptorEntry
SEQUENCE
	qatmTrafficDescriptorAlias	DisplayString

QatmTcEntry
SEQUENCE
	qatmTcCellSync	INTEGER
	qatmTcPortErrors	INTEGER
	qatmTcDmaErrors	INTEGER
	qatmInvalidCells	INTEGER
	qatmCellsForInactiveVcc	INTEGER

QatmAal5VccStatsEntry
SEQUENCE
	qatmAal5VccStatsInBytes	INTEGER
	qatmAal5VccStatsOutBytes	INTEGER
	qatmAal5VccStatsInSdus	INTEGER
	qatmAal5VccStatsOutSdus	INTEGER
	qatmAal5VccStatsErrsAndDiscards	INTEGER
	qatmAal5VccStatsLengthMismatchs	INTEGER
	qatmAal5VccStatsUserAborts	INTEGER
	qatmAal5VccStatsPoolDepleteds	INTEGER

QEventConfigEntry
SEQUENCE
	qEventConfigIndex	INTEGER
	qEventSeverityType	INTEGER
	qLogFileType	INTEGER
	qLogOption	INTEGER
	qDisplayOption	INTEGER
	qTrapOption	INTEGER

QEventSystemEntry
SEQUENCE
	qEventSystemIndex	INTEGER
	qEventSystemDateTime	DisplayString
	qEventSystemType	INTEGER
	qEventSystemSubSystem	INTEGER
	qEventSystemID-Number	INTEGER
	qEventSystemDescription	DisplayString

QEventAlarmEntry
SEQUENCE
	qEventAlarmIndex	INTEGER
	qEventAlarmDateTime	DisplayString
	qEventAlarmType	INTEGER
	qEventAlarmSubSystem	INTEGER
	qEventAlarmID-Number	INTEGER
	qEventAlarmDescription	DisplayString

QipCircExtEntry
SEQUENCE
	qipCircExtIndex	INTEGER
	qipCircExtIfIndex	INTEGER
	qipCircExtAdminState	INTEGER
	qipCircExtOperState	INTEGER

QarpCircExtEntry
SEQUENCE
	qarpCircExtIndex	INTEGER
	qarpCircExtIfIndex	INTEGER
	qarpCircExtDoProxy	INTEGER
	qarpCircExtDoResp	INTEGER

QripCircExtEntry
SEQUENCE
	qripCircExtIndex	INTEGER
	qripCircExtIfIndex	INTEGER
	qripCircExtTalk	INTEGER
	qripCircExtListen	INTEGER
	qripCircExtPoison	INTEGER

QMrRepairEntry
SEQUENCE
	qmrRepType	INTEGER
	qmrRepCode	Counter
	qmrRepDate	DisplayString
	qmrRepTime	DisplayString

QethernetCfgEntry
SEQUENCE
	qethernetMacAddress	PhysAddress
	qethernetSpeedMode	INTEGER
	qethernetEncapsulation	INTEGER
	qethernetAutoSense	INTEGER
	qethernetName	DisplayString

Qds1SpanCfgEntry
SEQUENCE
	qds1LineCfgIndex	INTEGER
	qds1LineBuildOut	INTEGER
	qds1ClockSourceEligibility	INTEGER
	qds1ClockMode	INTEGER
	qds1PerformanceMonitor	INTEGER
	qds1Scrambler	INTEGER

Qds1SpanLoopBackCmdEntry
SEQUENCE
	qds1LineLoopbackIndex	INTEGER
	qds1LoopbackCommand	INTEGER
	qds1LoopbackDuration	INTEGER

Qds1SpanLoopBackStatsEntry
SEQUENCE
	qds1LineLoopbackStatIndex	INTEGER
	qds1OamSegmentSent	Counter
	qds1OamSegmentReceived	Counter
	qds1OamSegmentFailures	Counter
	qds10amRunnigTime	Counter

QcmConfigEntry
SEQUENCE
	qcmTableIndex	INTEGER
	qcmCurrentConfig	INTEGER
	qcmActionOnConfig	INTEGER
	qcmFileAlias	DisplayString
	qcmRelease	DisplayString
	qcmConfigFile	DisplayString
	qcmBootSequence	DisplayString
	qcmCreateDateTime	DisplayString
	qcmOperSchedDateTime	DisplayString

QcmReleaseEntry
SEQUENCE
	qcmReleaseIndex	INTEGER
	qcmReleaseName	DisplayString
	qcmReleaseVersion	INTEGER

QcmConfigVerEntry
SEQUENCE
	qcmConfigVerIndex	INTEGER
	qcmConfigName	DisplayString
	qcmConfigVersion	INTEGER
	qcmConfigWorkWithMin	INTEGER
	qcmConfigWorkWithMax	INTEGER

QwesLpEntry
SEQUENCE
	qwesLpName	DisplayString
	qwesLpAlias	DisplayString
	qwesLpPhysicalInterface	INTEGER
	qwesLpDataLinkInterface	INTEGER
	qwesLpTrapStatus	INTEGER
	qwesLpAdminStatus	INTEGER
	qwesLpRowStatus	RowStatus

QwesLifEntry
SEQUENCE
	qwesLifName	DisplayString
	qwesLifAlias	DisplayString
	qwesLifLpIndex	INTEGER
	qwesLifTrapStatus	INTEGER
	qwesLifAdminStatus	INTEGER
	qwesLifRowStatus	RowStatus

QWESLIFENTRY
SEQUENCE
	qwesAtmArpLifIndex	INTEGER

QWESIPENTRY
SEQUENCE
	qIpLp	INTEGER
	qIpAddr	IpAddress
	qIpSubnet	IpAddress
	qIpMulticast	INTEGER
	qIpRipStatus	INTEGER
	qIpArpTimeout	INTEGER
	qIpEncap	INTEGER

QWESRIPENTRY
SEQUENCE
	qRipIpAddr	IpAddress
	qMode	INTEGER
	qAuthentication	DisplayString
	qSplitHorizon	INTEGER
	qAdvertiseStaticRoutes	INTEGER
	qAdvertiseIntf	INTEGER
	qBroadcastType	INTEGER
	qHoldDownInterval	INTEGER
	qUpdatesSend	INTEGER
	qUpdatesReceive	INTEGER
	qDefaultRouteMetric	INTEGER

QWESSTATICARPENTRY
SEQUENCE
	qStaticArpAddr	IpAddress
	qLif	INTEGER
	qPhysType	INTEGER
	qMacAddr	PhysAddress
	qType	INTEGER

QWESSTATICIGMPENTRY
SEQUENCE
	qIgmpStaticAddr	IpAddress
	qIgmpLp	INTEGER
	qIgmpType	INTEGER

QWESGroupIgmpEntry
SEQUENCE
	qIgmpGroupAddr	IpAddress
	qIgmpGroupLp	INTEGER
	qIgmpGroupMacAddr	PhysAddress
	qIgmpGroupInstallType	INTEGER

QWESRIPSTATSENTRY
SEQUENCE
	qRipStatsAddr	IpAddress
	qrip2IfStatsUpdatesReceives	INTEGER

QOAMGROUPCONFIGENTRY
SEQUENCE
	qoamGroupConfigIndex	INTEGER
	qoamGroupConfigAlias	DisplayString
	qoamGroupConfigType	INTEGER
	qoamGroupConfigTransmitInterval	INTEGER
	qoamGroupConfigS2SAlarmThreshold	INTEGER
	qoamGroupConfigE2EAlarmThreshold	INTEGER
	qoamGroupConfigStatus	INTEGER

QOAMCIRCUITCONFIGENTRY
SEQUENCE
	qoamCircuitConfigIndex	INTEGER
	qoamCircuitConfigType	INTEGER
	qoamCircuitConfigTransmitInterval	INTEGER
	qoamCircuitConfigS2SAlarmThreshold	INTEGER
	qoamCircuitConfigE2EAlarmThreshold	INTEGER
	qoamCircuitConfigStatus	INTEGER

QOAMGROUPCONTROLENTRY
SEQUENCE
	qoamGroupControlIndex	INTEGER
	qoamGroupControlType	INTEGER
	qoamGroupControlStatus	INTEGER

QOAMCIRCUITCONTROLENTRY
SEQUENCE
	qoamCircuitControlIndex	INTEGER
	qoamCircuitControlType	INTEGER
	qoamCircuitControlStatus	INTEGER

QOAMSTATSENTRY
SEQUENCE
	qoamStatsCircuit	INTEGER
	qoamStatsVpi	INTEGER
	qoamStatsVci	INTEGER
	qoamStatsType	INTEGER
	qoamStatsStatus	INTEGER
	qoamRequestTx	INTEGER
	qoamRequestRx	INTEGER
	qoamReplyRx	INTEGER
	qoamReplyTx	INTEGER
	qoamTimeouts	INTEGER
	qoamMinRt	INTEGER
	qoamMaxRt	INTEGER
	qoamAveRt	INTEGER
	qoamOtherInErrs	INTEGER
	qoamOtherOutErrs	INTEGER
	qoamCrc10InErrs	INTEGER
	qoamCrc10OutErrs	INTEGER

Defined Values

qwescom		1.3.6.1.4.1.3662
OBJECT IDENTIFIER

oemTree		1.3.6.1.4.1.3662.3662
OBJECT IDENTIFIER

oem		1.3.6.1.4.1.3662.3662.3662
OBJECT IDENTIFIER

qproprietaryMib2		1.3.6.1.4.1.3662.3662.3662.1
OBJECT IDENTIFIER

qproducts		1.3.6.1.4.1.3662.3662.3662.2
OBJECT IDENTIFIER

qslots		1.3.6.1.4.1.3662.3662.3662.3
OBJECT IDENTIFIER

qFlowClass		1.3.6.1.4.1.3662.3662.3662.4
OBJECT IDENTIFIER

qatm		1.3.6.1.4.1.3662.3662.3662.5
OBJECT IDENTIFIER

qcraftPort		1.3.6.1.4.1.3662.3662.3662.6
OBJECT IDENTIFIER

qeventGroup		1.3.6.1.4.1.3662.3662.3662.8
OBJECT IDENTIFIER

qextmib		1.3.6.1.4.1.3662.3662.3662.9
OBJECT IDENTIFIER

qmanufactRecord		1.3.6.1.4.1.3662.3662.3662.10
OBJECT IDENTIFIER

qethernet		1.3.6.1.4.1.3662.3662.3662.11
OBJECT IDENTIFIER

qds1-e1		1.3.6.1.4.1.3662.3662.3662.12
OBJECT IDENTIFIER

qconfigManager		1.3.6.1.4.1.3662.3662.3662.13
OBJECT IDENTIFIER

qportManagement		1.3.6.1.4.1.3662.3662.3662.15
OBJECT IDENTIFIER

qip		1.3.6.1.4.1.3662.3662.3662.16
OBJECT IDENTIFIER

qmanagementGroup		1.3.6.1.4.1.3662.3662.3662.17
OBJECT IDENTIFIER

qOamGroup		1.3.6.1.4.1.3662.3662.3662.18
OBJECT IDENTIFIER

qmiscGroup		1.3.6.1.4.1.3662.3662.3662.19
OBJECT IDENTIFIER

qsnmp		1.3.6.1.4.1.3662.3662.3662.1.11
OBJECT IDENTIFIER

qigmp		1.3.6.1.4.1.3662.3662.3662.16.7
OBJECT IDENTIFIER

qsnmpCommunityTable		1.3.6.1.4.1.3662.3662.3662.1.11.1
A list of SNMP Community entries. The maximum number of SNMP Communities are five.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QsnmpCommunityEntry

qsnmpCommunityEntry		1.3.6.1.4.1.3662.3662.3662.1.11.1.1
One entry in the table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	QsnmpCommunityEntry

qsnmpCommunityIndex		1.3.6.1.4.1.3662.3662.3662.1.11.1.1.1
A unique value which identifies each SNMP Community.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..4

qsnmpCommunityRights		1.3.6.1.4.1.3662.3662.3662.1.11.1.1.2
The first and third qsnmpCommunityIndex have read-write permission while the others have read-only privilege. Values 0 = ReadOnly, and 1 = ReadWrite
Status: optional	Access: read-only
OBJECT-TYPE
	INTEGER	readonly(0), readwrite(1)

qsnmpCommunityName		1.3.6.1.4.1.3662.3662.3662.1.11.1.1.3
The SNMP Community Name used to access the unit with the associated permission from the qsnmpCommunityRights.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

qsnmpNMSTable		1.3.6.1.4.1.3662.3662.3662.1.11.2
A list of SNMP Network Management System (NMS) entries.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QsnmpNMSEntry

qsnmpNMSEntry		1.3.6.1.4.1.3662.3662.3662.1.11.2.1
One entry in the table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	QsnmpNMSEntry

qsnmpNMSIndex		1.3.6.1.4.1.3662.3662.3662.1.11.2.1.1
A unique value which identifies each NMS.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..4

qsnmpNMSIpAddress		1.3.6.1.4.1.3662.3662.3662.1.11.2.1.2
The IP Address of a Network Management System, which is allowed to access MIB variables.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

qsnmpTrapTable		1.3.6.1.4.1.3662.3662.3662.1.11.3
A list of IP Address entries associated with traps.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QsnmpTrapEntry

qsnmpTrapEntry		1.3.6.1.4.1.3662.3662.3662.1.11.3.1
One entry in the table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	QsnmpTrapEntry

qsnmpTrapIndex		1.3.6.1.4.1.3662.3662.3662.1.11.3.1.1
A unique value which identifies each IP Address.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..4

qsnmpTrapIpAddress		1.3.6.1.4.1.3662.3662.3662.1.11.3.1.2
The IP Address of an IP entity, which is allowed to receive SNMP Trap events.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

qsnmpForwardTrap		1.3.6.1.4.1.3662.3662.3662.1.11.4
The flag which enables(1)/disables(2) SNMP Trap events to be transmitted.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

qClassDefinitionMaxEntries		1.3.6.1.4.1.3662.3662.3662.4.1
The number of Class Definition entries.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

qClassDefinitionTable		1.3.6.1.4.1.3662.3662.3662.4.2
A list of Class Definition entries. The number of entries is given by the value of qClassDefinitionMaxEntries.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QClassDefinitionEntry

qClassDefinitionEntry		1.3.6.1.4.1.3662.3662.3662.4.2.1
One entry in the table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	QClassDefinitionEntry

qClassDefinitionIndex		1.3.6.1.4.1.3662.3662.3662.4.2.1.1
A unique value for each class definition. Values 0 and 1 are reserved for internal use.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	2..1024

qClassDefinitionAlias		1.3.6.1.4.1.3662.3662.3662.4.2.1.2
A textual string containing user defined information about the Class Definition.
Status: optional	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

qClassDefinitionParentClassID		1.3.6.1.4.1.3662.3662.3662.4.2.1.3
The qClassDefinitionIndex value of the parent for this Class Definition.
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	0..1024

qClassDefinitionFlowType		1.3.6.1.4.1.3662.3662.3662.4.2.1.4
The type of Class Definition being created. INVALID causes the current Class Definition Entry to be removed.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	normal(1), dsingres(2), dsegress(3), dsnode(4), invalid(5)

qClassDefinitionSourceIPMask		1.3.6.1.4.1.3662.3662.3662.4.2.1.5
The IP address mask for the source.
Status: optional	Access: read-write
OBJECT-TYPE
	IpAddress

qClassDefinitionSourceIPLowerBound		1.3.6.1.4.1.3662.3662.3662.4.2.1.6
The first source IP address which matches the class (after masking).
Status: optional	Access: read-write
OBJECT-TYPE
	IpAddress

qClassDefinitionSourceIPUpperBound		1.3.6.1.4.1.3662.3662.3662.4.2.1.7
The last source IP address which matches the class (after masking).
Status: optional	Access: read-write
OBJECT-TYPE
	IpAddress

qClassDefinitionDestIPMask		1.3.6.1.4.1.3662.3662.3662.4.2.1.8
The IP address mask for the destination.
Status: optional	Access: read-write
OBJECT-TYPE
	IpAddress

qClassDefinitionDestIPLowerBound		1.3.6.1.4.1.3662.3662.3662.4.2.1.9
The first destination IP address which matches the class (after masking).
Status: optional	Access: read-write
OBJECT-TYPE
	IpAddress

qClassDefinitionDestIPUpperBound		1.3.6.1.4.1.3662.3662.3662.4.2.1.10
The last destination IP address which matches the class (after masking).
Status: optional	Access: read-write
OBJECT-TYPE
	IpAddress

qClassDefinitionDSMask		1.3.6.1.4.1.3662.3662.3662.4.2.1.11
The DS/TOS byte mask value.
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

qClassDefinitionDSLowerBound		1.3.6.1.4.1.3662.3662.3662.4.2.1.12
The first DS/TOS byte value which matches the class (after masking).
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

qClassDefinitionDSUpperBound		1.3.6.1.4.1.3662.3662.3662.4.2.1.13
The last DS/TOS byte value which matches the class (after masking).
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

qClassDefinitionWellKnownApplication		1.3.6.1.4.1.3662.3662.3662.4.2.1.14
The type of application to match.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	unspecified(0), realaudio(1), netmeeting(2), echo(3), discard(4), rip(5), daytime(5), quoteofday(6), msp(7), ftp(8), telnet(9), smtp(10), msg(11), time(12), rap(13), rlp(14), whois(15), login(16), remotemail(17), xns(18), dns(19), sql(20), bootp(21), tftp(22), gopher(23), finger(24), http(25), kerberos(26), npp(27), hostname(28), isotsap(29), remotetelnet(30), sna(31), pop3(32), rpc(33), authentication(34), audionews(35), sftp(36), uucp(37), networktime(38), pwdgen(39), ciscofna(40), ciscotna(41), ciscosys(42), netbios(43), news(44), management(45), send(46), appletalk(47), ipx(48), performancedata(49), ldap(50), novell(51), microsoft(52), doom(53), lotusnotes(54), audiomail(55), videomail(56), autodesk(57), ibm(58), vlsi(59), oracle(60), xwindows(61)

qClassDefinitionProtocol		1.3.6.1.4.1.3662.3662.3662.4.2.1.15
The IP protocol which matches the class.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	all(0), udptcp(1), udp(2), tcp(3), icmp(4), arp(5), rsvp(6), egp(7), ipinip(8), rdp(9), isotp4(10), idrp(11), pvp(12), isoip(13), vines(14), ttp(15), nsfnetigp(16), igrp(17), ospfigp(18)

qClassDefinitionSourcePortLowerBound		1.3.6.1.4.1.3662.3662.3662.4.2.1.16
The first source UDP/TCP port which matches the class. Only valid if qClassDefinitionWellKnownApplication = UNSPECIFIED, and qClassDefinitionProtocol = (ALL, UDPTCP, UDP, or TCP).
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

qClassDefinitionSourcePortUpperBound		1.3.6.1.4.1.3662.3662.3662.4.2.1.17
The last source UDP/TCP port which matches the class. Only valid if qClassDefinitionWellKnownApplication = UNSPECIFIED, and qClassDefinitionProtocol = (ALL, UDPTCP, UDP, or TCP).
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

qClassDefinitionDestPortLowerBound		1.3.6.1.4.1.3662.3662.3662.4.2.1.18
The first dest UDP/TCP port which matches the class. Only valid if qClassDefinitionWellKnownApplication = UNSPECIFIED, and qClassDefinitionProtocol = (ALL, UDPTCP, UDP, or TCP).
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

qClassDefinitionDestPortUpperBound		1.3.6.1.4.1.3662.3662.3662.4.2.1.19
The last dest UDP/TCP port which matches the class. Only valid if qClassDefinitionWellKnownApplication = UNSPECIFIED, and qClassDefinitionProtocol = (ALL, UDPTCP, UDP, or TCP).
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

qClassDefinitionFlowAgingTime		1.3.6.1.4.1.3662.3662.3662.4.2.1.20
The number of seconds to use as the aging time for LIF related flow information.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

qPolicyDefinitionMaxEntries		1.3.6.1.4.1.3662.3662.3662.4.3
The number of Policy Definition entries.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

qPolicyDefinitionTable		1.3.6.1.4.1.3662.3662.3662.4.4
A list of Policy Definition entries. The number of entries is given by the value of qPolicyDefinitionMaxEntries.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QPolicyDefinitionEntry

qPolicyDefinitionEntry		1.3.6.1.4.1.3662.3662.3662.4.4.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	QPolicyDefinitionEntry

qPolicyDefinitionIndex		1.3.6.1.4.1.3662.3662.3662.4.4.1.1
A unique value for each policy definition. Values 0 and 1 are reserved for internal use.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	2..1024

qPolicyDefinitionAlias		1.3.6.1.4.1.3662.3662.3662.4.4.1.2
A textual string containing user defined information about the Policy Definition.
Status: optional	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

qPolicyDefinitionType		1.3.6.1.4.1.3662.3662.3662.4.4.1.3
The type of Policy Definition. DELETE causes the current definition to be removed.
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	normal(1), dsingress(2), dsnode(3), dsegress(4), discard(5), delete(6)

qPolicyDefinitionLP		1.3.6.1.4.1.3662.3662.3662.4.4.1.4
The logical interface this policy relates to.
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	0..1024

qPolicyDefinitionStartTime		1.3.6.1.4.1.3662.3662.3662.4.4.1.5
The time of day this policy takes effect. NULL = always in effect.
Status: optional	Access: read-write
OBJECT-TYPE
	TimeDateString

qPolicyDefinitionEndTime		1.3.6.1.4.1.3662.3662.3662.4.4.1.6
The time of day this policy stops taking effect. NULL = always in effect.
Status: optional	Access: read-write
OBJECT-TYPE
	TimeDateString

qPolicyDefinitionDayofWeek		1.3.6.1.4.1.3662.3662.3662.4.4.1.7
Bit flags which indicate the day of week. Bit 0 = Monday, 1 = Tuesday, 2 = Weds, 4 = Thurs, 8 = Fri, 16 = Sat, 32 = Sun, 64 = Holidays.
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

qPolicyDefinitionPipeID		1.3.6.1.4.1.3662.3662.3662.4.4.1.8
The pipe definition this policy references.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..1024

qPolicyDefinitionClassID		1.3.6.1.4.1.3662.3662.3662.4.4.1.9
The class definition this policy references.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..1024

qPolicyDefinitionChannelized		1.3.6.1.4.1.3662.3662.3662.4.4.1.10
Bit flags indicating which Classing range is used to create unique channels. 0 = off, 1 = Source IP, 2 = Dest IP 4 = Source Port, 8 = Dest Port, 16 = Protocol, 32 = DS. The maximum number of channels (1-255) is set into the upper byte of this value. If a channel is selected, the default maximum is 16.
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

qPolicyDefinitionOutboundDSValue		1.3.6.1.4.1.3662.3662.3662.4.4.1.11
The DS/TOS byte value to set in outbound PDUs. A value of 256 indicates no replacement.
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	0..256

qPolicyDefinitionPriority		1.3.6.1.4.1.3662.3662.3662.4.4.1.12
The relative priority of this policy.
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

qPolicyDefinitionEvent		1.3.6.1.4.1.3662.3662.3662.4.4.1.13
The type of event which causes this policy to come into effect.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	static(1), time(2), reducedbw(3), increasedbw(4)

qPipeDefinitionMaxEntries		1.3.6.1.4.1.3662.3662.3662.4.5
The number of Pipe Definition entries.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

qPipeDefinitionTable		1.3.6.1.4.1.3662.3662.3662.4.6
A list of Pipe Definition entries. The number of entries is given by the value of qPipeDefinitionMaxEntries.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QPipeDefinitionEntry

qPipeDefinitionEntry		1.3.6.1.4.1.3662.3662.3662.4.6.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	QPipeDefinitionEntry

qPipeDefinitionIndex		1.3.6.1.4.1.3662.3662.3662.4.6.1.1
A unique value for each pipe definition. Values 0 and 1 are reserved for internal use.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	2..1024

qPipeDefinitionAlias		1.3.6.1.4.1.3662.3662.3662.4.6.1.2
A textual string containing user defined information about the Pipe Definition.
Status: optional	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

qPipeDefinitionType		1.3.6.1.4.1.3662.3662.3662.4.6.1.3
The type of Pipe Definition. DELETE causes the current definition to be removed.
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	valid(1), delete(2)

qPipeDefinitionCircuitID		1.3.6.1.4.1.3662.3662.3662.4.6.1.4
The WAN circuit this pipe relates to.
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	0..1024

qPipeDefinitionBandwidth		1.3.6.1.4.1.3662.3662.3662.4.6.1.5
The sustained bandwidth (bits/sec) of this pipe.
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER

qPipeDefinitionPeak		1.3.6.1.4.1.3662.3662.3662.4.6.1.6
Peak bandwidth of this pipe (bits/sec). Write-acces not supported in Release 1.
Status: optional	Access: read-only
OBJECT-TYPE
	INTEGER

qPipeDefinitionMBS		1.3.6.1.4.1.3662.3662.3662.4.6.1.7
The maximum burst size (bytes). Write-acces not supported in Release 1.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qPipeDefinitionBufferAllocation		1.3.6.1.4.1.3662.3662.3662.4.6.1.8
The maximum queuing delay for this pipe.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

qPipeDefinitionDelay		1.3.6.1.4.1.3662.3662.3662.4.6.1.9
The maximum queuing delay for this pipe.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

qPipeDefinitionPhyIdx		1.3.6.1.4.1.3662.3662.3662.4.6.1.10
The physical index for the port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qPipeDefinitionPhyType		1.3.6.1.4.1.3662.3662.3662.4.6.1.11
The physical type for the port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qClassStatisticsTable		1.3.6.1.4.1.3662.3662.3662.4.7
A list of Class Statistics entries. The number of entries is given by the value of qClassDefinitionMaxEntries.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QClassStatisticsEntry

qClassStatisticsEntry		1.3.6.1.4.1.3662.3662.3662.4.7.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	QClassStatisticsEntry

qClassStatisticsIndex		1.3.6.1.4.1.3662.3662.3662.4.7.1.1
A unique value for each class stats entry. These match their corresponding Class Definition entry index.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..1024

qClassStatisticsAlias		1.3.6.1.4.1.3662.3662.3662.4.7.1.2
A textual string containing user defined information about the Class Definition this stats entry relates to.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

qClassStatisticsTransmittedCount		1.3.6.1.4.1.3662.3662.3662.4.7.1.3
The number of bytes transmitted.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

qClassStatisticsDiscardCount		1.3.6.1.4.1.3662.3662.3662.4.7.1.4
The number of bytes discarded.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

qClassStatisticsFallbackCount		1.3.6.1.4.1.3662.3662.3662.4.7.1.5
The number of bytes transmitted on the 'all others' flow.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

qatmCircuitTable		1.3.6.1.4.1.3662.3662.3662.5.1
A list of ATM circuit entries.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QatmCircuitEntry

qatmCircuitEntry		1.3.6.1.4.1.3662.3662.3662.5.1.1
One entry in the table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	QatmCircuitEntry

qatmCircuitId		1.3.6.1.4.1.3662.3662.3662.5.1.1.1
A unique value for this circuit definition.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..1024

qatmCircuitAlias		1.3.6.1.4.1.3662.3662.3662.5.1.1.2
A unique alias for this circuit definition.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..52)

qatmCircuitUNI		1.3.6.1.4.1.3662.3662.3662.5.1.1.3
The UNI interface number for this circuit.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..1024

qatmCircuitLogicalInterface		1.3.6.1.4.1.3662.3662.3662.5.1.1.4
The LIF to assign this Circuit to. LIF 1 is reserved as an Ethernet identifier.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	2..1024

qatmCircuitVpi		1.3.6.1.4.1.3662.3662.3662.5.1.1.5
The Virtual Path Identifier for this circuit.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

qatmCircuitFirstVci		1.3.6.1.4.1.3662.3662.3662.5.1.1.6
The Virtual Path Identifier for this circuit.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

qatmCircuitMode		1.3.6.1.4.1.3662.3662.3662.5.1.1.7
Determining the multiplexing mode for this connection.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	cell(1), packet(2)

qatmCircuitStatus		1.3.6.1.4.1.3662.3662.3662.5.1.1.8
Setting a value of 1 adds/modifies an entry. Setting a value of 2 deletes a current entry.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	valid(1), deltete(2)

qatmUniTable		1.3.6.1.4.1.3662.3662.3662.5.2
This table contains the QWES.com proprietary configuration parameters for an ATM local Interface (UNI).
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QatmUniEntry

qatmUniEntry		1.3.6.1.4.1.3662.3662.3662.5.2.1
This list contains the QWES.com proprietary configuration parameters and state variables and is indexed by ifIndex values ATM interface.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	QatmUniEntry

qatmSpanPort		1.3.6.1.4.1.3662.3662.3662.5.2.1.1
The SPAN port associates with this UNI.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..25

qatmUniName		1.3.6.1.4.1.3662.3662.3662.5.2.1.2
Unique Name for this UNI.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

qatmUniAlias		1.3.6.1.4.1.3662.3662.3662.5.2.1.3
A textual string containing user defined information about the UNI.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

qatmUniTrapStatus		1.3.6.1.4.1.3662.3662.3662.5.2.1.4
Indicates whether the Link Up/Link Down traps should be generated for this interface.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

qatmUniMaxQueueDelay		1.3.6.1.4.1.3662.3662.3662.5.2.1.5
xxxx
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

qatmUniMinAllocBuffer		1.3.6.1.4.1.3662.3662.3662.5.2.1.6
xxxx
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

qatmUniSharedBuffer		1.3.6.1.4.1.3662.3662.3662.5.2.1.7
xxxx
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

qatmUniLinkBandwidth		1.3.6.1.4.1.3662.3662.3662.5.2.1.8
xxxx
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

qatmUniLinkDelay		1.3.6.1.4.1.3662.3662.3662.5.2.1.9
xxxx
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

qatmUniBandwidthGranularity		1.3.6.1.4.1.3662.3662.3662.5.2.1.10
xxxx
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

qatmUniIlmiStatus		1.3.6.1.4.1.3662.3662.3662.5.2.1.11
Enable/Disable ILMI function for this UNI.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

qatmUniRowStatus		1.3.6.1.4.1.3662.3662.3662.5.2.1.12
This object is used to create, delete or modify a row in this table.
Status: mandatory	Access: read-write
OBJECT-TYPE
	RowStatus

qatmVplTable		1.3.6.1.4.1.3662.3662.3662.5.3
The Virtual Path Link (VPL) table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QatmVplEntry

qatmVplEntry		1.3.6.1.4.1.3662.3662.3662.5.3.1
One entry in the table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	QatmVplEntry

qatmVplMaxVcc		1.3.6.1.4.1.3662.3662.3662.5.3.1.1
The maximum number of VCCs initialized and active for this VPC. If the value is 0, then this VPC is only for management purposes and is not assigned to a scheduler.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..1024

qatmVplLowestVci		1.3.6.1.4.1.3662.3662.3662.5.3.1.2
The start of a contiguous and increasing VCI range whose maximum is given by the maximum VCCs allowed.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

qatmVplMaxQueueDelay		1.3.6.1.4.1.3662.3662.3662.5.3.1.3
The maximum queueing delay in milliseconds (msec). Combining this value with the sustained rate will determine the maximum buffering allowed.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

qatmVplReservedBuffer		1.3.6.1.4.1.3662.3662.3662.5.3.1.4
The minimum amount of buffering that this VCC will be allocated to use.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

qatmVplBwGranularity		1.3.6.1.4.1.3662.3662.3662.5.3.1.5
The bandwidth granularity can be apply to this VPC.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

qatmVplMtu		1.3.6.1.4.1.3662.3662.3662.5.3.1.6
The MTU size can be apply to this VPC.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

qatmVplSharedBuffer		1.3.6.1.4.1.3662.3662.3662.5.3.1.7
The amount of buffering to be assigned to a VPC for sharing on a First In First Out (FIFO) basis between flows on this VPC.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

qatmVclTable		1.3.6.1.4.1.3662.3662.3662.5.4
The Virtual Channel Link (VCL) table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QatmVclEntry

qatmVclEntry		1.3.6.1.4.1.3662.3662.3662.5.4.1
One entry in the table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	QatmVclEntry

qatmVclBwGranularity		1.3.6.1.4.1.3662.3662.3662.5.4.1.1
The bandwidth granularity can be apply to this VCC.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

qatmVclMaxSubChannels		1.3.6.1.4.1.3662.3662.3662.5.4.1.2
The maximum number of sub-channels supported on this Virtual Circuit.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

qatmVclMaxQueueDelay		1.3.6.1.4.1.3662.3662.3662.5.4.1.3
The maximum queueing delay in milliseconds (msec). Combining this value with the sustained rate will determine the maximum buffering allowed.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

qatmVclReservedBuffer		1.3.6.1.4.1.3662.3662.3662.5.4.1.4
The minimum reserved buffer in bytes that this VCC will be allocated to use.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

qatmVclSharedBuffer		1.3.6.1.4.1.3662.3662.3662.5.4.1.5
The amount of buffering to be assigned to a VCC for sharing on a First In First Out (FIFO) basis between flows on this VCC.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

qatmAal5Table		1.3.6.1.4.1.3662.3662.3662.5.5
The ATM Adaptation Layer 5 (Aal5) table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QatmAal5Entry

qatmAal5Entry		1.3.6.1.4.1.3662.3662.3662.5.5.1
One entry in the table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	QatmAal5Entry

qatmAal5Uni		1.3.6.1.4.1.3662.3662.3662.5.5.1.1
The UNI port alias associates with this AAL5 interface.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..25

qatmAal5Aal5Name		1.3.6.1.4.1.3662.3662.3662.5.5.1.2
The AAL5 port name.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

qatmAal5Aal5Alias		1.3.6.1.4.1.3662.3662.3662.5.5.1.3
The alias for this AAL5 interface.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

qatmAal5AdminStatus		1.3.6.1.4.1.3662.3662.3662.5.5.1.4
The desired state for this interface.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	up(1), down(2)

qatmAal5TrapStatus		1.3.6.1.4.1.3662.3662.3662.5.5.1.5
Indicates whether the Link Up/Link Down traps should be generated for this interface.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

qatmAal5MtuSize		1.3.6.1.4.1.3662.3662.3662.5.5.1.6
Set the largest PDU size for the AAL5 CPCS layer that cen be processed by the AAL5 entity.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

qatmAal5RowStatus		1.3.6.1.4.1.3662.3662.3662.5.5.1.7
Indicate the entry's status. (1..5 = add) 6 = delete.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..6

qatmTrafficDescriptorTable		1.3.6.1.4.1.3662.3662.3662.5.6
The TrafficDescriptor table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QatmTrafficDescriptorEntry

qatmTrafficDescriptorEntry		1.3.6.1.4.1.3662.3662.3662.5.6.1
One entry in the table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	QatmTrafficDescriptorEntry

qatmTrafficDescriptorAlias		1.3.6.1.4.1.3662.3662.3662.5.6.1.1
The alias for this traffic descriptor.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

qatmTcTable		1.3.6.1.4.1.3662.3662.3662.5.7
The ATM TC table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QatmTcEntry

qatmTcEntry		1.3.6.1.4.1.3662.3662.3662.5.7.1
One entry in the table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	QatmTcEntry

qatmTcCellSync		1.3.6.1.4.1.3662.3662.3662.5.7.1.1
The number of cell sync occurred on this Tc interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qatmTcPortErrors		1.3.6.1.4.1.3662.3662.3662.5.7.1.2
The number of errors received on this Tc interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qatmTcDmaErrors		1.3.6.1.4.1.3662.3662.3662.5.7.1.3
The number of DMA errors received on this Tc interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qatmInvalidCells		1.3.6.1.4.1.3662.3662.3662.5.7.1.4
The number of invalid cellls received on this Tc interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qatmCellsForInactiveVcc		1.3.6.1.4.1.3662.3662.3662.5.7.1.5
The number of cellls received for an inactive Vcc.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qatmAal5VccStatsTable		1.3.6.1.4.1.3662.3662.3662.5.8
The ATM AAL5 Vcc Statistics table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QatmAal5VccStatsEntry

qatmAal5VccStatsEntry		1.3.6.1.4.1.3662.3662.3662.5.8.1
One entry in the table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	QatmAal5VccStatsEntry

qatmAal5VccStatsInBytes		1.3.6.1.4.1.3662.3662.3662.5.8.1.1
The number of bytes received by this AAL5 interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qatmAal5VccStatsOutBytes		1.3.6.1.4.1.3662.3662.3662.5.8.1.2
The number of bytes send by this AAL5 interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qatmAal5VccStatsInSdus		1.3.6.1.4.1.3662.3662.3662.5.8.1.3
The number of SDUs received by this AAL5 interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qatmAal5VccStatsOutSdus		1.3.6.1.4.1.3662.3662.3662.5.8.1.4
The number of SDUs send by this AAL5 interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qatmAal5VccStatsErrsAndDiscards		1.3.6.1.4.1.3662.3662.3662.5.8.1.5
The number of error and discard packets received by this AAL5 interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qatmAal5VccStatsLengthMismatchs		1.3.6.1.4.1.3662.3662.3662.5.8.1.6
The number of length mismatched packets received by this AAL5 interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qatmAal5VccStatsUserAborts		1.3.6.1.4.1.3662.3662.3662.5.8.1.7
The number of packets aborted by users.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qatmAal5VccStatsPoolDepleteds		1.3.6.1.4.1.3662.3662.3662.5.8.1.8
The number of packets aborted by users.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qcpStatus		1.3.6.1.4.1.3662.3662.3662.6.1
Tok_String
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	down(0), up(1)

qcpBaudRate		1.3.6.1.4.1.3662.3662.3662.6.2
The craft port command baud rate.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	br-1200(0), br-2400(1), br-4800(2), br-9600(3), br-14400(4), br-19200(5), br-28800(6), br-38400(7), br-57600(8), br-115200(9)

qcpStopBitLength		1.3.6.1.4.1.3662.3662.3662.6.3
Tok_String
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	sb-1(0), sb-2(1)

qcpParity		1.3.6.1.4.1.3662.3662.3662.6.4
Tok_String
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	even(0), odd(1), none(2)

qcpDataBits		1.3.6.1.4.1.3662.3662.3662.6.5
Tok_String
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	db-7(0), db-8(1)

qcpCharsSent		1.3.6.1.4.1.3662.3662.3662.6.6
Tok_String
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

qcpCharsReceived		1.3.6.1.4.1.3662.3662.3662.6.7
Tok_String
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

qEventConfigTable		1.3.6.1.4.1.3662.3662.3662.8.1
A list of Event System Configuration Entries used for viewing / changing event options
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QEventConfigEntry

qEventConfigEntry		1.3.6.1.4.1.3662.3662.3662.8.1.1
One entry in the table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	QEventConfigEntry

qEventConfigIndex		1.3.6.1.4.1.3662.3662.3662.8.1.1.1
A unique value for each event that has been logged into one of the Event Logs
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..6

qEventSeverityType		1.3.6.1.4.1.3662.3662.3662.8.1.1.2
A unique value which identifies each Event Type (Severity).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	fatal(1), critical(2), mild(3), standard-snmp(4), informational(5), debug(6)

qLogFileType		1.3.6.1.4.1.3662.3662.3662.8.1.1.3
A unique value which allows the selection of the type of Log file to Log events into.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	alarm(1), system(2), none(3)

qLogOption		1.3.6.1.4.1.3662.3662.3662.8.1.1.4
A flag which enables(1)/disables(2) the logging feature of the Event Subsystem
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

qDisplayOption		1.3.6.1.4.1.3662.3662.3662.8.1.1.5
A flag which enables(1)/disables(2) the display feature of the Event Subsystem
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

qTrapOption		1.3.6.1.4.1.3662.3662.3662.8.1.1.6
A flag which enables(1)/disables(2) the Send Trap feature of the Event Subsystem
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

qEventSystemTable		1.3.6.1.4.1.3662.3662.3662.8.2
A list of Event Log Display entries used for viewing the Logs.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QEventSystemEntry

qEventSystemEntry		1.3.6.1.4.1.3662.3662.3662.8.2.1
One entry in the table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	QEventSystemEntry

qEventSystemIndex		1.3.6.1.4.1.3662.3662.3662.8.2.1.1
A unique value for each event that has been logged into one of the Event Logs
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..255

qEventSystemDateTime		1.3.6.1.4.1.3662.3662.3662.8.2.1.2
The time of day an event occurs SNMP Community.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

qEventSystemType		1.3.6.1.4.1.3662.3662.3662.8.2.1.3
This value will be used to identify the Event Type to be displayed
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	fatal(1), critical(2), mild(3), standard-snmp(4), informational(5), debug(6)

qEventSystemSubSystem		1.3.6.1.4.1.3662.3662.3662.8.2.1.4
This value will be used to identify the Event Type to be displayed
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	general-subsystem(1), ip-subsystem(2), atm-subsystem(3), ethernet-subsystem(4), tftp-subsystem(5), telnet-subsystem(6), clip-subsystem(7), flash-subsystem(8), flow-subsystem(9), serial-subsystem(10), port-manager-subsystem(11), get-subsystem(12), oam-subsystem(13), reset-subsystem(14), time-subsystem(15), icmp-subsystem(16), igmp-subsystem(17), ping-subsystem(18), snmp-subsystem(19), tcp-subsystem(20), upd-subsystem(21), lp-subsystem(22), lif-subsystem(23), circuit-subsystem(24), arp-subsystem(25)

qEventSystemID-Number		1.3.6.1.4.1.3662.3662.3662.8.2.1.5
A unique value for each event that has been logged into one of the Event Logs
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qEventSystemDescription		1.3.6.1.4.1.3662.3662.3662.8.2.1.6
A textual string containing the Description of the occurred Event.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

qEventAlarmTable		1.3.6.1.4.1.3662.3662.3662.8.3
A list of Event Log Display entries used for viewing the Logs.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QEventAlarmEntry

qEventAlarmEntry		1.3.6.1.4.1.3662.3662.3662.8.3.1
One entry in the table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	QEventAlarmEntry

qEventAlarmIndex		1.3.6.1.4.1.3662.3662.3662.8.3.1.1
A unique value for each event that has been logged into one of the Event Logs
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..255

qEventAlarmDateTime		1.3.6.1.4.1.3662.3662.3662.8.3.1.2
The time of day an event occurs SNMP Community.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

qEventAlarmType		1.3.6.1.4.1.3662.3662.3662.8.3.1.3
This value will be used to identify the Event Type to be displayed
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	fatal(1), critical(2), mild(3), standard-snmp(4), informational(5), debug(6)

qEventAlarmSubSystem		1.3.6.1.4.1.3662.3662.3662.8.3.1.4
This value will be used to identify the Event Type to be displayed
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	general-subsystem(1), ip-subsystem(2), atm-subsystem(3), ethernet-subsystem(4), tftp-subsystem(5), telnet-subsystem(6), clip-subsystem(7), flash-subsystem(8), flow-subsystem(9), serial-subsystem(10), port-manager-subsystem(11), get-subsystem(12), oam-subsystem(13), reset-subsystem(14), time-subsystem(15), icmp-subsystem(16), igmp-subsystem(17), ping-subsystem(18), snmp-subsystem(19), tcp-subsystem(20), upd-subsystem(21), lp-subsystem(22), lif-subsystem(23), circuit-subsystem(24), arp-subsystem(25)

qEventAlarmID-Number		1.3.6.1.4.1.3662.3662.3662.8.3.1.5
A unique value for each event that has been logged into one of the Event Logs
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qEventAlarmDescription		1.3.6.1.4.1.3662.3662.3662.8.3.1.6
A textual string containing the Description of the occurred Event.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

qipExt		1.3.6.1.4.1.3662.3662.3662.9.1
OBJECT IDENTIFIER

qarpExt		1.3.6.1.4.1.3662.3662.3662.9.2
OBJECT IDENTIFIER

qripExt		1.3.6.1.4.1.3662.3662.3662.9.3
OBJECT IDENTIFIER

qipCircExtTable		1.3.6.1.4.1.3662.3662.3662.9.1.1
Table of IP circuit parameters
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QipCircExtEntry

qipCircExtEntry		1.3.6.1.4.1.3662.3662.3662.9.1.1.1
A circuits IP parameters
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	QipCircExtEntry

qipCircExtIndex		1.3.6.1.4.1.3662.3662.3662.9.1.1.1.1
An index value which uniquely identifies this circuit within the router. This may or may not be related to the physical interface index.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qipCircExtIfIndex		1.3.6.1.4.1.3662.3662.3662.9.1.1.1.2
An index value which uniquely identifies the local physical interface which this circuit uses. This value identifies the same interface identified by ifIndex in MIB-2.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qipCircExtAdminState		1.3.6.1.4.1.3662.3662.3662.9.1.1.1.3
Enable or disable the operation of IP on the specified interface.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

qipCircExtOperState		1.3.6.1.4.1.3662.3662.3662.9.1.1.1.4
The operational state of the circuit. May or may not be the same as administrative state.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	off(1), on(2)

qarpExtTtl		1.3.6.1.4.1.3662.3662.3662.9.2.1
The lifetime of an ARP entry within the router.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

qarpCircExtTable		1.3.6.1.4.1.3662.3662.3662.9.2.2
Table of ARP circuit parameters
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QarpCircExtEntry

qarpCircExtEntry		1.3.6.1.4.1.3662.3662.3662.9.2.2.1
A circuits ARP parameters
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	QarpCircExtEntry

qarpCircExtIndex		1.3.6.1.4.1.3662.3662.3662.9.2.2.1.1
An index value which uniquely identifies this circuit within the router. This may or may not be related to the physical interface index.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qarpCircExtIfIndex		1.3.6.1.4.1.3662.3662.3662.9.2.2.1.2
An index value which uniquely identifies the local physical interface which this circuit uses. This value identifies the same interface identified by ifIndex in MIB-2.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qarpCircExtDoProxy		1.3.6.1.4.1.3662.3662.3662.9.2.2.1.3
Enable or disable ARP proxy responses on the specified interface.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

qarpCircExtDoResp		1.3.6.1.4.1.3662.3662.3662.9.2.2.1.4
Enable or disable the sending of ARP responses on specified circuit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

qripExtAdminState		1.3.6.1.4.1.3662.3662.3662.9.3.1
Enable or disable the operation of RIP on all interfaces.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

qripExtUpdateTime		1.3.6.1.4.1.3662.3662.3662.9.3.2
The time between transmission of RIP updates.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

qripCircExtTable		1.3.6.1.4.1.3662.3662.3662.9.3.3
Table of RIP circuit parameters
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QripCircExtEntry

qripCircExtEntry		1.3.6.1.4.1.3662.3662.3662.9.3.3.1
A circuits RIP parameters
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	QripCircExtEntry

qripCircExtIndex		1.3.6.1.4.1.3662.3662.3662.9.3.3.1.1
An index value which uniquely identifies this circuit within the router. This may or may not be related to the physical interface index.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qripCircExtIfIndex		1.3.6.1.4.1.3662.3662.3662.9.3.3.1.2
An index value which uniquely identifies the local physical interface which this circuit uses. This value identifies the same interface identified by ifIndex in MIB-2.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qripCircExtTalk		1.3.6.1.4.1.3662.3662.3662.9.3.3.1.3
Enable or disable RIP transmission on the specified interface.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

qripCircExtListen		1.3.6.1.4.1.3662.3662.3662.9.3.3.1.4
Enable or disable RIP reception on the specified interface.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

qripCircExtPoison		1.3.6.1.4.1.3662.3662.3662.9.3.3.1.5
Enable or disable operation of poison reverse on the specified interface. If poison is disabled, split-horzon operation is enabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

qmrCheckSum		1.3.6.1.4.1.3662.3662.3662.10.1
The checksum of the manufacturing record.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

qmrBurnDate		1.3.6.1.4.1.3662.3662.3662.10.2
The Date the manufacturing record was burned into flash.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

qmrBurnTime		1.3.6.1.4.1.3662.3662.3662.10.3
The time the manufacturing record was burned into flash.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

qmrOemName		1.3.6.1.4.1.3662.3662.3662.10.4
The OEM Name of the unit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

qmrOemID		1.3.6.1.4.1.3662.3662.3662.10.5
The OEM ID of the unit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

qmrSerialNumber		1.3.6.1.4.1.3662.3662.3662.10.6
The serial number of the unit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

qmrProductID		1.3.6.1.4.1.3662.3662.3662.10.7
The product ID of the unit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	qwes-span(1)

qmrModelID		1.3.6.1.4.1.3662.3662.3662.10.8
The model ID of the unit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	prototype(1), rev3(2)

qmrMacAddress		1.3.6.1.4.1.3662.3662.3662.10.9
The MAC address of the unit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	PhysAddress

qmrRepairTable		1.3.6.1.4.1.3662.3662.3662.10.10
List of Repairs performed on the unit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	SEQUENCE OF
		QMrRepairEntry

qmrRepairEntry		1.3.6.1.4.1.3662.3662.3662.10.10.1
List of Repairs performed on the unit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	QMrRepairEntry

qmrRepType		1.3.6.1.4.1.3662.3662.3662.10.10.1.1
The Type of the repair.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	repair(1), eco(2)

qmrRepCode		1.3.6.1.4.1.3662.3662.3662.10.10.1.2
The code of the repair.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

qmrRepDate		1.3.6.1.4.1.3662.3662.3662.10.10.1.3
The date of the repair.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

qmrRepTime		1.3.6.1.4.1.3662.3662.3662.10.10.1.4
The time of the repair.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

qethernetCfgTable		1.3.6.1.4.1.3662.3662.3662.11.1
A list of Ethernet Configuration entries. The maximum number is based on the maximum interfaces.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QethernetCfgEntry

qethernetCfgEntry		1.3.6.1.4.1.3662.3662.3662.11.1.1
The Ethernet configuration information for each Ethernet interface.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	QethernetCfgEntry

qethernetMacAddress		1.3.6.1.4.1.3662.3662.3662.11.1.1.1
The ethernet's physical address. An six byte hexidecimal identifier, which identifies the interface on the physical media.
Status: mandatory	Access: read-write
OBJECT-TYPE
	PhysAddress

qethernetSpeedMode		1.3.6.1.4.1.3662.3662.3662.11.1.1.2
The Ethernet chipset has five available modes: (1) 100-MBPS-FULL-DUPLEX - sets ethernet chipset to 100 mbps, full duplex mode; (2) 10-MBPS-FULL-DUPLEX - sets ethernet chipset to 10 mbps, full duplex mode; (3) 100-MBPS-HALF-DUPLEX - sets ethernet chipset to 100 mbps, half duplex mode; (4) 10-MBPS-HALF-DUPLEX - sets ethernet chipset to 10 mbps, half duplex mode.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	full-duplex-100-mbps(1), full-duplex-10-mbps(2), half-duplex-100-mbps(3), half-duplex-10-mbps(4)

qethernetEncapsulation		1.3.6.1.4.1.3662.3662.3662.11.1.1.3
The flag which sets the ethernets encapsulation type. 1 = Ethernet Version 2 encapsulation; 2 = IEEE 802.3 encapsulation.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	etherv2encap(1), ieee8023encap(2)

qethernetAutoSense		1.3.6.1.4.1.3662.3662.3662.11.1.1.4
This object is used to negotiate the speed/duplex. The default is set to YES (1) - which negotiates from the configured speed/duplex (qethernetSpeedMode) or lower. When set to NO (2) - this forces the configured speed/duplex mode and will not establish a link unless the other end complies.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	yes(1), no(2)

qethernetName		1.3.6.1.4.1.3662.3662.3662.11.1.1.5
This object is used to???
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

qethernetCurrentSpeedMode		1.3.6.1.4.1.3662.3662.3662.11.1.1.6
The Ethernet chipset has four available modes or operation: (1) 100-MBPS-FULL-DUPLEX - sets ethernet chipset to 100 mbps, full duplex mode; (2) 10-MBPS-FULL-DUPLEX - sets ethernet chipset to 10 mbps, full duplex mode; (3) 100-MBPS-HALF-DUPLEX - sets ethernet chipset to 100 mbps, half duplex mode; (4) 10-MBPS-HALF-DUPLEX - sets ethernet chipset to 10 mbps, half duplex mode. This object will provide the current speed/duplex achieved or 'No Link'.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	full-duplex-100-mbps(1), full-duplex-10-mbps(2), half-duplex-100-mbps(3), half-duplex-10-mbps(4), no-link(5)

qds1AutoClockSourceSearching		1.3.6.1.4.1.3662.3662.3662.12.1
Selecting (1) YES will allow the Policy Point unit to automatically select the next available SPAN to provide clock if the Primary Clock Source fails. Selecting (2) NO will instruct the unit to ignore all clock source ports except the primary source clock port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	yes(1), no(2)

qds1PrimaryClockSource		1.3.6.1.4.1.3662.3662.3662.12.2
Identifies the unit's primary clock source. The first SPAN port - (2) SPAN-1; the second SPAN port - (3) SPAN-2; the third SPAN port - (4) SPAN-3; the fourth SPAN port - (5) SPAN-4; the fifth SPAN port - (6) SPAN-5; the sixth SPAN port - (7) SPAN-6.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	span-1(2), span-2(3), span-3(4), span-4(5), span-5(6), span-6(7)

qds1PrimaryClockSourceAction		1.3.6.1.4.1.3662.3662.3662.12.3
Instructs the Span unit to (1) USE-CURRENT-SOURCE - stay with the current source clock, or (2) RETURN-TO-PRIMARY-SOURCE - restore the clock to the primary clock source.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	use-current-source(1), restore-to-primary-source(2)

qds1SpanCfgTable		1.3.6.1.4.1.3662.3662.3662.12.4
A list of Span Configuration entries. The maximum number is based on the maximum interfaces.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Qds1SpanCfgEntry

qds1SpanCfgEntry		1.3.6.1.4.1.3662.3662.3662.12.4.1
The DS1/E1 configuration information for each DS1/E1 interface.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	Qds1SpanCfgEntry

qds1LineCfgIndex		1.3.6.1.4.1.3662.3662.3662.12.4.1.1
A unique value which identifies a DS1/E1 interface. This value 'should' be made equal to the ifIndex, however, this may not be the case, but will have an internal association with the ifEntry.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qds1LineBuildOut		1.3.6.1.4.1.3662.3662.3662.12.4.1.2
The Line Build Out specification for the DS1/E1 interface. NOTE: (1) represents not only the LINE-BUILD-OUT-133-FT, but also 0 db CSU.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	line-build-out-133-ft(1), line-build-out-266-ft(2), line-build-out-399-ft(3), line-build-out-533-ft(4), line-build-out-655-ft(5), line-build-out-n7-5db(6), line-build-out-n15db(7), line-build-out-n22-5db(8), not-applicable(9)

qds1ClockSourceEligibility		1.3.6.1.4.1.3662.3662.3662.12.4.1.3
Identifies whether the DS1/E1 interface is eligible to be the source clock or not.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	eligible(1), ineligible(2)

qds1ClockMode		1.3.6.1.4.1.3662.3662.3662.12.4.1.4
Identifies the clock's mode of operation. Setting the clock mode to (1) will allow the interface to act as the slave to the network clock, and setting the mode to (2) will allow the unit's interface to provide the master clock.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	slavetonetwork(1), providemasterclock(2)

qds1PerformanceMonitor		1.3.6.1.4.1.3662.3662.3662.12.4.1.5
Indicates whether or not performance monitoring will be transmitted on this interface. ENABLE (1) will transmit the performance report according to the ANSI T1.403-1995 standard. The performance report contains performance information for each of the four previous one-second intervals.
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

qds1Scrambler		1.3.6.1.4.1.3662.3662.3662.12.4.1.6
Indicates whether or not scrambling of data is being generated on this interface. ENABLE (1) will transmit the scrambled data according to the ITU-T 0.191 Recommendation; DISABLE (2) will not scramble the data. NOTE: A T1 interface will NOT support scrambling, and therefore will be DISABLED.
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

qds1SpanLoopBackCmdTable		1.3.6.1.4.1.3662.3662.3662.12.5
A list of Span Loopback Configuration entries. The maximum number is based on the maximum DS1/E1 interfaces.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Qds1SpanLoopBackCmdEntry

qds1SpanLoopBackCmdEntry		1.3.6.1.4.1.3662.3662.3662.12.5.1
The DS1/E1 loopback configuration information for each DS1/E1 interface.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	Qds1SpanLoopBackCmdEntry

qds1LineLoopbackIndex		1.3.6.1.4.1.3662.3662.3662.12.5.1.1
A unique value which identifies DS1/E1 interface. This value should be made equal to the ifIndex.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qds1LoopbackCommand		1.3.6.1.4.1.3662.3662.3662.12.5.1.2
This object is used to (1) ACTIVATE the configured loopback on the selected interface (qds1LineIndex) of the specified entity. If the dsx1OtherLoop (4) has been configured (see rfc2495 - dsx1LoopbackConfig), the supported loopback is the Local Port Loopback (LPL). The Local Port Loopback is used to validate the ability to send and receive data to the local DS1/E1 interface. LPL will use OAM flow to verify data transfer. Normal OAM flows are discontinued and an F4 OAM segment flow is automatically started on VPI=0, VCI=3 with a repeat timer of 1 second. When the loopback is set to (2) DEACTIVATE or comes to completion, the previous OAM configuration flows are restored.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	activate(1), deactivate(2)

qds1LoopbackDuration		1.3.6.1.4.1.3662.3662.3662.12.5.1.3
The value indicates the duration (in SECONDS) that the Loopback will be in process.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..3600

qds1SpanLoopBackStatsTable		1.3.6.1.4.1.3662.3662.3662.12.6
A list of Span Loopback Statistics for each entries. The maximum number is based on the maximum DS1/E1 interfaces.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Qds1SpanLoopBackStatsEntry

qds1SpanLoopBackStatsEntry		1.3.6.1.4.1.3662.3662.3662.12.6.1
The DS1/E1 loopback statistics information foreach DS1/E1 interface.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	Qds1SpanLoopBackStatsEntry

qds1LineLoopbackStatIndex		1.3.6.1.4.1.3662.3662.3662.12.6.1.1
A unique value which identifies DS1/E1 interface. This value should be made equal to the ifIndex.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qds1OamSegmentSent		1.3.6.1.4.1.3662.3662.3662.12.6.1.2
The total number of segment OAM messages transmitted on the DS1/E1 interface in question for the duration of the test.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

qds1OamSegmentReceived		1.3.6.1.4.1.3662.3662.3662.12.6.1.3
The total number of segment OAM messages received on the DS1/E1 interface in question for the duration of the test.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

qds1OamSegmentFailures		1.3.6.1.4.1.3662.3662.3662.12.6.1.4
The total number of segment OAM messages timed out on the DS1/E1 interface in question for the duration of the test.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

qds10amRunnigTime		1.3.6.1.4.1.3662.3662.3662.12.6.1.5
This is running time for the loop back.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

qcmSystemFile		1.3.6.1.4.1.3662.3662.3662.13.1
The name of the configuration file to edit.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

qcmConfigMaxEntries		1.3.6.1.4.1.3662.3662.3662.13.2
The number of Configuration entries.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

qcmConfigTable		1.3.6.1.4.1.3662.3662.3662.13.3
A list of configuration file entries. The number of entries is given by the value of qcmConfigMaxEntries.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QcmConfigEntry

qcmConfigEntry		1.3.6.1.4.1.3662.3662.3662.13.3.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	QcmConfigEntry

qcmTableIndex		1.3.6.1.4.1.3662.3662.3662.13.3.1.1
A unique value for each config file.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

qcmCurrentConfig		1.3.6.1.4.1.3662.3662.3662.13.3.1.2
Flag that indicates if this record is the current operational configuration.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(0), yes(1)

qcmActionOnConfig		1.3.6.1.4.1.3662.3662.3662.13.3.1.3
Operations that can be performed on the current table record.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), delete(1), activatenow(2), activatelater(3), save(4), saveas(5)

qcmFileAlias		1.3.6.1.4.1.3662.3662.3662.13.3.1.4
The file alias name of the 'release' / 'configuration file' pair.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

qcmRelease		1.3.6.1.4.1.3662.3662.3662.13.3.1.5
The name of the release file (executable).
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

qcmConfigFile		1.3.6.1.4.1.3662.3662.3662.13.3.1.6
The name of the configuration file.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

qcmBootSequence		1.3.6.1.4.1.3662.3662.3662.13.3.1.7
The boot sequence.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

qcmCreateDateTime		1.3.6.1.4.1.3662.3662.3662.13.3.1.8
The creation date and time of the configuration file.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..30)

qcmOperSchedDateTime		1.3.6.1.4.1.3662.3662.3662.13.3.1.9
The date and time the configuration file became operational.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..30)

qcmReleaseTable		1.3.6.1.4.1.3662.3662.3662.13.4
A list of Release file entries.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QcmReleaseEntry

qcmReleaseEntry		1.3.6.1.4.1.3662.3662.3662.13.4.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	QcmReleaseEntry

qcmReleaseIndex		1.3.6.1.4.1.3662.3662.3662.13.4.1.1
A unique value for each Release file.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

qcmReleaseName		1.3.6.1.4.1.3662.3662.3662.13.4.1.2
The name of a release file.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..20)

qcmReleaseVersion		1.3.6.1.4.1.3662.3662.3662.13.4.1.3
The version of the release file.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..4294967295

qcmConfigVerTable		1.3.6.1.4.1.3662.3662.3662.13.5
A list of Config file entries.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QcmConfigVerEntry

qcmConfigVerEntry		1.3.6.1.4.1.3662.3662.3662.13.5.1
Tok_String
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	QcmConfigVerEntry

qcmConfigVerIndex		1.3.6.1.4.1.3662.3662.3662.13.5.1.1
A unique value for each Config file.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

qcmConfigName		1.3.6.1.4.1.3662.3662.3662.13.5.1.2
The name of a Config file.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..20)

qcmConfigVersion		1.3.6.1.4.1.3662.3662.3662.13.5.1.3
The version of the Config file.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..4294967295

qcmConfigWorkWithMin		1.3.6.1.4.1.3662.3662.3662.13.5.1.4
The minimum version of a Release file the Config file is compatable with.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..4294967295

qcmConfigWorkWithMax		1.3.6.1.4.1.3662.3662.3662.13.5.1.5
The maximum version of a Release file the Config file is compatable with.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..4294967295

qcmWhichFile		1.3.6.1.4.1.3662.3662.3662.13.6
Which file to do SNMP GETs and SETS on.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	operational(0), base(1), new(2), default(3)

qcmUserBaseCfgFile		1.3.6.1.4.1.3662.3662.3662.13.7
The name of the configuration file to edit.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

qcmUserNewCfgFile		1.3.6.1.4.1.3662.3662.3662.13.8
The name of the new configuration file.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

qcmUserFileAlias		1.3.6.1.4.1.3662.3662.3662.13.9
The file alias of the system file.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

qcmUserRelease		1.3.6.1.4.1.3662.3662.3662.13.10
The name of the release file.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

qcmUserBootSequence		1.3.6.1.4.1.3662.3662.3662.13.11
The boot sequence.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..40)

qcmUserDateTime		1.3.6.1.4.1.3662.3662.3662.13.12
The date and time LDF is be scheduled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..30)

qcmStartConfig		1.3.6.1.4.1.3662.3662.3662.13.13
Start the configuration process.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(0), yes(1)

qcmStopConfig		1.3.6.1.4.1.3662.3662.3662.13.14
Stop and Save the current configuration process.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(0), yes(1)

qcmStartViewConfig		1.3.6.1.4.1.3662.3662.3662.13.15
Start viewing a configuration file.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(0), yes(1)

qcmStopViewConfig		1.3.6.1.4.1.3662.3662.3662.13.16
Stop viewing a configuration file.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(0), yes(1)

qcmCancelConfig		1.3.6.1.4.1.3662.3662.3662.13.17
Cancel the current configuration process.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	no(0), yes(1)

qwesLpTable		1.3.6.1.4.1.3662.3662.3662.15.1
A list of Logical Port entries.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QwesLpEntry

qwesLpEntry		1.3.6.1.4.1.3662.3662.3662.15.1.1
One entry in the table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	QwesLpEntry

qwesLpName		1.3.6.1.4.1.3662.3662.3662.15.1.1.1
Display the name for the Logical Port.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

qwesLpAlias		1.3.6.1.4.1.3662.3662.3662.15.1.1.2
Enter an alias for the Logical Port Inteface name that has significant to your organization.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

qwesLpPhysicalInterface		1.3.6.1.4.1.3662.3662.3662.15.1.1.3
The physical port that this Logical Port associated.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..16

qwesLpDataLinkInterface		1.3.6.1.4.1.3662.3662.3662.15.1.1.4
The data link port that this Logical Port associated.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	25..88

qwesLpTrapStatus		1.3.6.1.4.1.3662.3662.3662.15.1.1.5
Indicates whether the Link Up/Link Down traps should be generated for this interface.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	yes(1), no(2)

qwesLpAdminStatus		1.3.6.1.4.1.3662.3662.3662.15.1.1.6
The desired state of the interface set by management.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	up(1), down(2)

qwesLpRowStatus		1.3.6.1.4.1.3662.3662.3662.15.1.1.7
This object is used to create a new row or modify or delete an existing row in this table.
Status: mandatory	Access: read-write
OBJECT-TYPE
	RowStatus

qwesLifTable		1.3.6.1.4.1.3662.3662.3662.15.2
A list of Logical Interface entries.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QwesLifEntry

qwesLifEntry		1.3.6.1.4.1.3662.3662.3662.15.2.1
One entry in the table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	QwesLifEntry

qwesLifName		1.3.6.1.4.1.3662.3662.3662.15.2.1.1
The name for the Logical Port.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

qwesLifAlias		1.3.6.1.4.1.3662.3662.3662.15.2.1.2
The alias for the logical inteface name that has significant to your organization.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

qwesLifLpIndex		1.3.6.1.4.1.3662.3662.3662.15.2.1.3
The logical port (LP) number that this logical interface has an association with.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	257..512

qwesLifTrapStatus		1.3.6.1.4.1.3662.3662.3662.15.2.1.4
Indicates whether the Link Up/Link Down traps should be generated for this interface.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	yes(1), no(2)

qwesLifAdminStatus		1.3.6.1.4.1.3662.3662.3662.15.2.1.5
The desired state of the interface set by management.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	up(1), down(2)

qwesLifRowStatus		1.3.6.1.4.1.3662.3662.3662.15.2.1.6
This object is used to create a new row or modify or delete an existing row in this table.
Status: mandatory	Access: read-write
OBJECT-TYPE
	RowStatus

qwesAtmArpTable		1.3.6.1.4.1.3662.3662.3662.15.3
A list of ATM ARP entries.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QWESLIFENTRY

qwesAtmArpEntry		1.3.6.1.4.1.3662.3662.3662.15.3.1
One entry in the table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	QWESLIFENTRY

qwesAtmArpLifIndex		1.3.6.1.4.1.3662.3662.3662.15.3.1.1
The logical interfacne (LIF) number that this ATM ARP entry has an association with.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qSysTime		1.3.6.1.4.1.3662.3662.3662.17.1
System Time in GMT.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..28)

qTftpType		1.3.6.1.4.1.3662.3662.3662.17.2
The file upload type. 1 = operational, 2 = config
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

qTftpFileName		1.3.6.1.4.1.3662.3662.3662.17.3
Local filename to download into. If it exists, it WILL be overwritten.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..128)

qTftpServerIpAddress		1.3.6.1.4.1.3662.3662.3662.17.4
Server's IP address
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

qTftpServerFileName		1.3.6.1.4.1.3662.3662.3662.17.5
Server's filename to get
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..128)

qTftpAdminStatus		1.3.6.1.4.1.3662.3662.3662.17.6
set to 1 to start TFTP download. 0 = ready for next download.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

qTftpOperStatus		1.3.6.1.4.1.3662.3662.3662.17.7
0=idle, 1=reading, 2=server IP error, 3=server filename error, 4 = done
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qTftpRxCount		1.3.6.1.4.1.3662.3662.3662.17.8
Number of blocks received
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qTimeZone		1.3.6.1.4.1.3662.3662.3662.17.9
Current time zone of the unit.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	eniwetok(1), samoa(2), hawaii(3), alaska(4), pacific(5), arizona(6), mountain(7), central(8), atlantic(9), newfoundland(10), buenos-aires(11), mid-atlantic(12), azores(13), gmt(14), paris(15), israel(16), moscow(17), tehran(18), abu-dhabi(19), islamabad(20), almaty(21), bangkok(22), beijing(23), tokyo(24), brisbane(25), new-caledonia(26), auckland(27)

qipPortTable		1.3.6.1.4.1.3662.3662.3662.16.1
A list of IP Port entries.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QWESIPENTRY

qipPortEntry		1.3.6.1.4.1.3662.3662.3662.16.1.1
One entry in the table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	QWESIPENTRY

qIpLp		1.3.6.1.4.1.3662.3662.3662.16.1.1.1
The logical port number associated with this IP port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

qIpAddr		1.3.6.1.4.1.3662.3662.3662.16.1.1.2
The IP address of this IP Port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

qIpSubnet		1.3.6.1.4.1.3662.3662.3662.16.1.1.3
The IP subnet ddress of this IP Port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

qIpMulticast		1.3.6.1.4.1.3662.3662.3662.16.1.1.4
Indicate whether or not multicast will be transmit on this interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

qIpRipStatus		1.3.6.1.4.1.3662.3662.3662.16.1.1.5
Indicate the RIP status.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

qIpArpTimeout		1.3.6.1.4.1.3662.3662.3662.16.1.1.6
The elapsed time of seconds before an ARP entry can be removed from the ARP table.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

qIpEncap		1.3.6.1.4.1.3662.3662.3662.16.1.1.7
Indicate the encapsulation type.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	standard(1), hp(2)

qRipPortTable		1.3.6.1.4.1.3662.3662.3662.16.2
A list of IP Port entries.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QWESRIPENTRY

qRipPortEntry		1.3.6.1.4.1.3662.3662.3662.16.2.1
One entry in the table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	QWESRIPENTRY

qRipIpAddr		1.3.6.1.4.1.3662.3662.3662.16.2.1.1
The IP address associated with this RIP Port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

qMode		1.3.6.1.4.1.3662.3662.3662.16.2.1.2
Selects what type of rip authentication to be used on the selected port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), password(2), md5(3)

qAuthentication		1.3.6.1.4.1.3662.3662.3662.16.2.1.3
This is the password to be used, when password type is selected for above authentication.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..16)

qSplitHorizon		1.3.6.1.4.1.3662.3662.3662.16.2.1.4
.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	poisoned-reverse(1), simple(2), disable(3)

qAdvertiseStaticRoutes		1.3.6.1.4.1.3662.3662.3662.16.2.1.5
.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	yes(1), no(2)

qAdvertiseIntf		1.3.6.1.4.1.3662.3662.3662.16.2.1.6
.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	yes(1), no(2)

qBroadcastType		1.3.6.1.4.1.3662.3662.3662.16.2.1.7
.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	local(1), direct-with-ones(2), direct-with-zeros(3)

qHoldDownInterval		1.3.6.1.4.1.3662.3662.3662.16.2.1.8
.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

qUpdatesSend		1.3.6.1.4.1.3662.3662.3662.16.2.1.9
What the router sends on this interface. ripVersion1 implies sending RIP updates compliant with RFC 1058. rip1Compatible implies broadcasting RIP-2 updates using RFC 1058 route subsumption rules. ripVersion2 implies multicasting RIP-2 updates. ripV1Demand indicates the use of Demand RIP on a WAN interface under RIP Version 1 rules. ripV2Demand indicates the use of Demand RIP on a WAN interface under Version 2 rules.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	silent(1), version-1(2), rip-1-compatible(3), version-2(4), version-1-demand(5), version-2-demand(6)

qUpdatesReceive		1.3.6.1.4.1.3662.3662.3662.16.2.1.10
This indicates which version of RIP updates are to be accepted. Note that rip2 and rip1OrRip2 implies reception of multicast packets.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	rip1(1), rip2(2), rip1-or-rip2(3), none(3)

qDefaultRouteMetric		1.3.6.1.4.1.3662.3662.3662.16.2.1.11
This variable indicates the metric that is to be used for the default route entry in RIP updates originated on this interface. A value of zero indicates that no default route should be originated; in this case, a default route via another router may be propagated.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..15

qStaticArpTable		1.3.6.1.4.1.3662.3662.3662.16.3
A list of Static ARP entries.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QWESSTATICARPENTRY

qStaticArpEntry		1.3.6.1.4.1.3662.3662.3662.16.3.1
One entry in the table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	QWESSTATICARPENTRY

qStaticArpAddr		1.3.6.1.4.1.3662.3662.3662.16.3.1.1
The IP address associated with this ARP entry.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

qLif		1.3.6.1.4.1.3662.3662.3662.16.3.1.2
The Logical Interface which uniquely identifies the local interface which this ARP entry can be reached.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	513..1536

qPhysType		1.3.6.1.4.1.3662.3662.3662.16.3.1.3
The physical interface type associated with this ARP entry.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ethernet(1), atm-and-others(2)

qMacAddr		1.3.6.1.4.1.3662.3662.3662.16.3.1.4
The physical address associated with this ARP entry.
Status: mandatory	Access: read-write
OBJECT-TYPE
	PhysAddress

qType		1.3.6.1.4.1.3662.3662.3662.16.3.1.5
Defines the ARP entry current status. Setting this entry to invalid(2) has the effect of invalidating the correspding entry in the ARP table. Setting this entry to valid(1) has the effect of installing the entry in the ARP table and make it active.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	add-activate(1), add-not-activate(2), delete(3)

qipTtl		1.3.6.1.4.1.3662.3662.3662.16.4
The time-to-live (in seconds) that a packet can live in the network.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

qipRoutePriority		1.3.6.1.4.1.3662.3662.3662.16.5
The route priority indicates routing entry precedence in the system. If RIP is selected, then all routing entries learned by RIP will have higher priority then other entries. Also, if STATIC is selected, then all routing entries which are static defined will have higher priority then other entries.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	rip(1), static(2)

qipRipStatus		1.3.6.1.4.1.3662.3662.3662.16.6
The RIP system flag.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

qigmpInMsgs		1.3.6.1.4.1.3662.3662.3662.16.7.1
Messages received by the system.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qigmpOutMsgs		1.3.6.1.4.1.3662.3662.3662.16.7.2
Messages transmitted by the system.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qigmpInErrors		1.3.6.1.4.1.3662.3662.3662.16.7.3
Error messages received by the system.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qigmpInReports		1.3.6.1.4.1.3662.3662.3662.16.7.4
Reported messages received by the system.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qigmpInQueries		1.3.6.1.4.1.3662.3662.3662.16.7.5
Querries received by the system.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qigmpInUnknownType		1.3.6.1.4.1.3662.3662.3662.16.7.6
Unkown messages received by the system.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qIgmpStaticTable		1.3.6.1.4.1.3662.3662.3662.16.7.7
A list of Static IGMP entries.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QWESSTATICIGMPENTRY

qIgmpStaticEntry		1.3.6.1.4.1.3662.3662.3662.16.7.7.1
One entry in the table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	QWESSTATICIGMPENTRY

qIgmpStaticAddr		1.3.6.1.4.1.3662.3662.3662.16.7.7.1.1
The IP address associated with this IGMP entry.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

qIgmpLp		1.3.6.1.4.1.3662.3662.3662.16.7.7.1.2
The logical port number associated with this IP port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

qIgmpType		1.3.6.1.4.1.3662.3662.3662.16.7.7.1.3
Defines the IGMP entry current status. Setting this entry to invalid(2) has the effect of invalidating the correspding entry in the IGMP table. Setting this entry to valid(1) has the effect of installing the entry in the IGMP table and make it active.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	add-activate(1), add-not-activate(2), delete(3)

qIgmpGroupTable		1.3.6.1.4.1.3662.3662.3662.16.7.8
A list of IGMP Group entries.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QWESGroupIgmpEntry

qIgmpGroupEntry		1.3.6.1.4.1.3662.3662.3662.16.7.8.1
One entry in the table.
Status: current	Access: not-accessible
OBJECT-TYPE
	QWESGroupIgmpEntry

qIgmpGroupAddr		1.3.6.1.4.1.3662.3662.3662.16.7.8.1.1
The Multicast IP address associated with this IGMP entry.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

qIgmpGroupLp		1.3.6.1.4.1.3662.3662.3662.16.7.8.1.2
The logical port number associated with this IP port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

qIgmpGroupMacAddr		1.3.6.1.4.1.3662.3662.3662.16.7.8.1.3
The Multicast MAC address associated with the qIgmpGroupLp.
Status: current	Access: read-only
OBJECT-TYPE
	PhysAddress

qIgmpGroupInstallType		1.3.6.1.4.1.3662.3662.3662.16.7.8.1.4
Defines how the multicast IP was installed. Static(1) entries are specifically created by the user. Dynamic(2) entries are learned. All others are unknown.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	static(1), dynamic(2), unknown(3)

qarpInMsgs		1.3.6.1.4.1.3662.3662.3662.16.13
Arp messages received by the system.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qarpOutMsgs		1.3.6.1.4.1.3662.3662.3662.16.14
Arp messages send by the system.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qarpReqInMsg		1.3.6.1.4.1.3662.3662.3662.16.15
Request Arp messages received by the system.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qarpReqOutMsgs		1.3.6.1.4.1.3662.3662.3662.16.16
Arp request messages send by the system.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qarpRespInMsgs		1.3.6.1.4.1.3662.3662.3662.16.17
Arp reply messages received by the system.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qarpRespOutMsgs		1.3.6.1.4.1.3662.3662.3662.16.18
Arp reply messages send by the system.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qarpSendDiscards		1.3.6.1.4.1.3662.3662.3662.16.19
Arp discard messages send by the system.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qarpSendTimeouts		1.3.6.1.4.1.3662.3662.3662.16.20
Arp timeout messages send by the system.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qarpInResourceErrors		1.3.6.1.4.1.3662.3662.3662.16.21
Lack of resources Arp messages received by the system.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qarpOutResourceErrors		1.3.6.1.4.1.3662.3662.3662.16.22
Lack of resources Arp messages send by the system.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

qRipStatsTable		1.3.6.1.4.1.3662.3662.3662.16.23
A list of Static ARP entries.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QWESRIPSTATSENTRY

qRipStatsEntry		1.3.6.1.4.1.3662.3662.3662.16.23.1
One entry in the table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	QWESRIPSTATSENTRY

qRipStatsAddr		1.3.6.1.4.1.3662.3662.3662.16.23.1.1
Rip updates received by this system.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	IpAddress

qrip2IfStatsUpdatesReceives		1.3.6.1.4.1.3662.3662.3662.16.23.1.2
Rip updates received by this system.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

qoamGroupConfigTable		1.3.6.1.4.1.3662.3662.3662.18.1
A list of OAM group Configurable Parameters entries.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QOAMGROUPCONFIGENTRY

qoamGroupConfigEntry		1.3.6.1.4.1.3662.3662.3662.18.1.1
One entry in the table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	QOAMGROUPCONFIGENTRY

qoamGroupConfigIndex		1.3.6.1.4.1.3662.3662.3662.18.1.1.1
The entry index of a particular group. Currently, there are 6 groups define: 1) All circuit 2) All Uni1 3) All Uni2, 4) All Uni3, 5) All Vpl, 6) All Vcl.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

qoamGroupConfigAlias		1.3.6.1.4.1.3662.3662.3662.18.1.1.2
Alias name of a specified circuit or for all configured UNIs, 1=end-to-end, 2=segment-to-segment, 3=both.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

qoamGroupConfigType		1.3.6.1.4.1.3662.3662.3662.18.1.1.3
The type of OAM to be generated.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	segment-2-segment(1), end-2-end(2), both(3)

qoamGroupConfigTransmitInterval		1.3.6.1.4.1.3662.3662.3662.18.1.1.4
The interval between OAM transmission in seconds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

qoamGroupConfigS2SAlarmThreshold		1.3.6.1.4.1.3662.3662.3662.18.1.1.5
The number of timed out segment-to-segment OAM replies accumulated in sequence before an alarm is generated.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

qoamGroupConfigE2EAlarmThreshold		1.3.6.1.4.1.3662.3662.3662.18.1.1.6
The number of timed out end-to-end OAM replies accumulated in sequence before an alarm is generated.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

qoamGroupConfigStatus		1.3.6.1.4.1.3662.3662.3662.18.1.1.7
Enable/disable OAM operation.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

qoamCircuitConfigTable		1.3.6.1.4.1.3662.3662.3662.18.2
A list of OAM Configurable Parameters entries.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QOAMCIRCUITCONFIGENTRY

qoamCircuitConfigEntry		1.3.6.1.4.1.3662.3662.3662.18.2.1
One entry in the table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	QOAMCIRCUITCONFIGENTRY

qoamCircuitConfigIndex		1.3.6.1.4.1.3662.3662.3662.18.2.1.1
The index for the selected circuit.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..1024

qoamCircuitConfigType		1.3.6.1.4.1.3662.3662.3662.18.2.1.2
The type of OAM to be generated.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	segment-2-segment(1), end-2-end(2), both(3)

qoamCircuitConfigTransmitInterval		1.3.6.1.4.1.3662.3662.3662.18.2.1.3
The interval between OAM transmission in seconds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

qoamCircuitConfigS2SAlarmThreshold		1.3.6.1.4.1.3662.3662.3662.18.2.1.4
The number of timed out segment-to-segment OAM replies accumulated in sequence before an alarm is generated.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

qoamCircuitConfigE2EAlarmThreshold		1.3.6.1.4.1.3662.3662.3662.18.2.1.5
The number of timed out end-to-end OAM replies accumulated in sequence before an alarm is generated.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

qoamCircuitConfigStatus		1.3.6.1.4.1.3662.3662.3662.18.2.1.6
Enable/disable OAM operation.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	add-activate(1), add-not-activate(2), delete(3)

qoamGroupControlTable		1.3.6.1.4.1.3662.3662.3662.18.3
A list of OAM Control Parameters entries.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QOAMGROUPCONTROLENTRY

qoamGroupControlEntry		1.3.6.1.4.1.3662.3662.3662.18.3.1
One entry in the table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	QOAMGROUPCONTROLENTRY

qoamGroupControlIndex		1.3.6.1.4.1.3662.3662.3662.18.3.1.1
The index for the selected circuit.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..256

qoamGroupControlType		1.3.6.1.4.1.3662.3662.3662.18.3.1.2
The type of OAM to be generated, 1=end-to-end, 2=segment-to-segment, 3=both.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	segment-2-segment(1), end-2-end(2), both(3)

qoamGroupControlStatus		1.3.6.1.4.1.3662.3662.3662.18.3.1.3
Initiate or terminate OAM operation, 1=start and 2=stop
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	start(1), stop(2), restore(3)

qoamCircuitControlTable		1.3.6.1.4.1.3662.3662.3662.18.4
A list of OAM Control Parameters entry.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QOAMCIRCUITCONTROLENTRY

qoamCircuitControlEntry		1.3.6.1.4.1.3662.3662.3662.18.4.1
One entry in the table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	QOAMCIRCUITCONTROLENTRY

qoamCircuitControlIndex		1.3.6.1.4.1.3662.3662.3662.18.4.1.1
The index for the selected circuit.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..1024

qoamCircuitControlType		1.3.6.1.4.1.3662.3662.3662.18.4.1.2
The type of OAM to be generated, 1=end-to-end, 2=segment-to-segment, 3=both.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	segment-2-segment(1), end-2-end(2), both(3)

qoamCircuitControlStatus		1.3.6.1.4.1.3662.3662.3662.18.4.1.3
Initiate or terminate OAM operation, 1=start and 2=stop
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	start(1), stop(2), restore(3)

qoamStatsTable		1.3.6.1.4.1.3662.3662.3662.18.5
A list of OAM statistics entries.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QOAMSTATSENTRY

qoamStatsEntry		1.3.6.1.4.1.3662.3662.3662.18.5.1
One entry in the table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	QOAMSTATSENTRY

qoamStatsCircuit		1.3.6.1.4.1.3662.3662.3662.18.5.1.1
The circuit id identifies the entry.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

qoamStatsVpi		1.3.6.1.4.1.3662.3662.3662.18.5.1.2
The first half of the VPI/VCI pairs associated with the circuit id.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

qoamStatsVci		1.3.6.1.4.1.3662.3662.3662.18.5.1.3
The second half of the VPI/VCI pairs associated with the circuit id.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

qoamStatsType		1.3.6.1.4.1.3662.3662.3662.18.5.1.4
The type of OAM.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	f4-segment(1), f4-end(2), f5-segment(3), f5-end(4)

qoamStatsStatus		1.3.6.1.4.1.3662.3662.3662.18.5.1.5
The current operational status of OAM on this circuit. ON=OAMs being transmitted, OFF=OAMs not being transmitted.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(2)

qoamRequestTx		1.3.6.1.4.1.3662.3662.3662.18.5.1.6
The total number of OAM requests transmitted.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

qoamRequestRx		1.3.6.1.4.1.3662.3662.3662.18.5.1.7
The total number of OAM requests received.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

qoamReplyTx		1.3.6.1.4.1.3662.3662.3662.18.5.1.8
The total number of OAM replies transmitted.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

qoamReplyRx		1.3.6.1.4.1.3662.3662.3662.18.5.1.9
The total number of OAM replies received.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

qoamTimeouts		1.3.6.1.4.1.3662.3662.3662.18.5.1.10
The total number of OAM replies that were not received before timeout.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

qoamMinRt		1.3.6.1.4.1.3662.3662.3662.18.5.1.11
The minimum round trip time in seconds for receiving OAM replies since the counters were last reset.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

qoamMaxRt		1.3.6.1.4.1.3662.3662.3662.18.5.1.12
The maximun round trip time in seconds for receiving OAM replies since the counters were last reset.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

qoamAveRt		1.3.6.1.4.1.3662.3662.3662.18.5.1.13
The average round trip time in seconds for receiving OAM replies since the counters were last reset.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

qoamOtherInErrs		1.3.6.1.4.1.3662.3662.3662.18.5.1.14
The number of OAM received but discarded due to errors.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

qoamOtherOutErrs		1.3.6.1.4.1.3662.3662.3662.18.5.1.15
The number of OAM can't transmitted due to errors.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

qoamCrc10InErrs		1.3.6.1.4.1.3662.3662.3662.18.5.1.16
The number of OAM received but discarded due to crc-10 checksum error.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

qoamCrc10OutErrs		1.3.6.1.4.1.3662.3662.3662.18.5.1.17
The number of OAM can't transmitted due to crc-10 checksum error.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER