PRVT-SAA-MIB

File: PRVT-SAA-MIB.mib (66905 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
SNMP-FRAMEWORK-MIB PRVT-SWITCH-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Unsigned32
Counter32 NOTIFICATION-TYPE IpAddress
Integer32 Counter64 MODULE-COMPLIANCE
OBJECT-GROUP NOTIFICATION-GROUP RowStatus
TruthValue DisplayString TEXTUAL-CONVENTION
SnmpAdminString switch

Defined Types

PrvtSaaY1731PmTestEntry  
SEQUENCE    
  prvtSaaY1731PmTestOwner SnmpAdminString
  prvtSaaY1731PmTestName SnmpAdminString
  prvtSaaY1731PmTestType INTEGER
  prvtSaaY1731PmTestExecStatus INTEGER
  prvtSaaY1731PmTestEncapType INTEGER
  prvtSaaY1731PmTestEncapValue Unsigned32
  prvtSaaY1731PmTestUserPort Unsigned32
  prvtSaaY1731PmTestUplinkPort Unsigned32
  prvtSaaY1731PmTestTargetMac DisplayString
  prvtSaaY1731PmTestCfmDomainLevel Unsigned32
  prvtSaaY1731PmTestRemoteCfmMep Unsigned32
  prvtSaaY1731PmTestProfile Unsigned32
  prvtSaaY1731PmTestHistoryDepth Unsigned32
  prvtSaaY1731PmTestPeriod Unsigned32
  prvtSaaY1731PmTestTimeout Unsigned32
  prvtSaaY1731PmTestMonitorInterval Unsigned32
  prvtSaaY1731PmTestFrequency Unsigned32
  prvtSaaY1731PmTestClocksInSync TruthValue
  prvtSaaY1731PmTestDelayMethod INTEGER
  prvtSaaY1731PmTestDelayPvalue Unsigned32
  prvtSaaY1731PmTestJitterMethod INTEGER
  prvtSaaY1731PmTestJitterPvalue Unsigned32
  prvtSaaY1731PmTestPriority Unsigned32
  prvtSaaY1731PmTestRowStatus RowStatus
  prvtSaaY1731PmTestCCMAPSCount TruthValue
  prvtSaaY1731PmTestLossMeasurementType INTEGER
  prvtSaaY1731PmTestSLMTransmit TruthValue
  prvtSaaY1731PmTestTestId Unsigned32
  prvtSaaY1731PmTestDropEligible TruthValue
  prvtSaaY1731PmTestDataSize Unsigned32
  prvtSaaY1731PmTestCountAllPriorities TruthValue

PrvtSaaRFC2544ThroughputTestEntry  
SEQUENCE    
  prvtSaaRFC2544ThroughputTestOwner SnmpAdminString
  prvtSaaRFC2544ThroughputTestName SnmpAdminString
  prvtSaaRFC2544ThroughputTestType INTEGER
  prvtSaaRFC2544ThroughputTestExecStatus INTEGER
  prvtSaaRFC2544ThroughputTestSourceType INTEGER
  prvtSaaRFC2544ThroughputTestSource OCTET STRING
  prvtSaaRFC2544ThroughputTestTargetType INTEGER
  prvtSaaRFC2544ThroughputTestTarget OCTET STRING
  prvtSaaRFC2544ThroughputTestTimeout Unsigned32
  prvtSaaRFC2544ThroughputTestCIR Unsigned32
  prvtSaaRFC2544ThroughputTestCBS Unsigned32
  prvtSaaRFC2544ThroughputTestBurstPercentage Unsigned32
  prvtSaaRFC2544ThroughputTestDuration Unsigned32
  prvtSaaRFC2544ThroughputTestMaxFrameloss Unsigned32
  prvtSaaRFC2544ThroughputTestCVLAN0 Unsigned32
  prvtSaaRFC2544ThroughputTestCVLAN0Priority Unsigned32
  prvtSaaRFC2544ThroughputTestCVLAN0DropEligible TruthValue
  prvtSaaRFC2544ThroughputTestSVLAN Unsigned32
  prvtSaaRFC2544ThroughputTestSVLANPriority Unsigned32
  prvtSaaRFC2544ThroughputTestSVLANDropEligible TruthValue
  prvtSaaRFC2544ThroughputTestPDUSize DisplayString
  prvtSaaRFC2544ThroughputTestACKTimeout Unsigned32
  prvtSaaRFC2544ThroughputTestLoopbackType INTEGER
  prvtSaaRFC2544ThroughputTestPaternType INTEGER
  prvtSaaRFC2544ThroughputTestRowStatus RowStatus
  prvtSaaRFC2544ThroughputTestEthertype OCTET STRING

PrvtSaaY1731LoopbackTestEntry  
SEQUENCE    
  prvtSaaY1731LoopbackTestEncapType INTEGER
  prvtSaaY1731LoopbackTestEncapValue Unsigned32
  prvtSaaY1731LoopbackTestUserPort Unsigned32
  prvtSaaY1731LoopbackTestUplinkPort Unsigned32
  prvtSaaY1731LoopbackTestType INTEGER
  prvtSaaY1731LoopbackTestRowStatus RowStatus
  prvtSaaY1731LoopbackTestCCMAPSCount TruthValue
  prvtSaaY1731LoopbackTestCountAllPriorities TruthValue

PrvtSaaY1731TestResultEntry  
SEQUENCE    
  prvtSaaY1731TestResultIndex Unsigned32
  prvtSaaY1731TestResultDelayNE Unsigned32
  prvtSaaY1731TestResultDelayFE Unsigned32
  prvtSaaY1731TestResultJitterNE Unsigned32
  prvtSaaY1731TestResultJitterFE Unsigned32
  prvtSaaY1731TestResultFrameLossNE Unsigned32
  prvtSaaY1731TestResultFrameLossFE Unsigned32
  prvtSaaY1731TestResultFramesSentNE Counter32
  prvtSaaY1731TestResultFramesSentFE Counter32
  prvtSaaY1731TestResultFramesRcvdNE Counter32
  prvtSaaY1731TestResultFramesRcvdFE Counter32
  prvtSaaY1731TestResultPacketsSent Counter32
  prvtSaaY1731TestResultNoTimeouts Unsigned32
  prvtSaaY1731TestResultNoErrors Unsigned32
  prvtSaaY1731TestResultCompletionTime Unsigned32

PrvtSaaRFC2544TestResultEntry  
SEQUENCE    
  prvtSaaRFC2544TestResultIndex Unsigned32
  prvtSaaRFC2544TestResultFrameSize Unsigned32
  prvtSaaRFC2544TestResultFrameLoss Unsigned32
  prvtSaaRFC2544TestResultThroughput Unsigned32
  prvtSaaRFC2544TestResultNetThroughput Unsigned32
  prvtSaaRFC2544TestResultStatus INTEGER
  prvtSaaRFC2544TestResultDelayMinimum Unsigned32
  prvtSaaRFC2544TestResultDelayAverage Unsigned32
  prvtSaaRFC2544TestResultDelayMaximum Unsigned32

PrvtSaaProfileEntry  
SEQUENCE    
  prvtSaaProfileIndex Unsigned32
  prvtSaaProfileDelayNE Unsigned32
  prvtSaaProfileDelayFE Unsigned32
  prvtSaaProfileJitterNE Unsigned32
  prvtSaaProfileJitterFE Unsigned32
  prvtSaaProfileFrameLossNE Unsigned32
  prvtSaaProfileFrameLossFE Unsigned32
  prvtSaaProfileRowStatus RowStatus
  prvtSaaProfileName OCTET STRING

PrvtTwampTestNameType  
TWAMP test name type (1..32 characters).
TEXTUAL-CONVENTION    
  OCTET STRING Size(1..32)  

PrvtTwampDecimalPercent  
A percentage value in decimal format.
TEXTUAL-CONVENTION    
  OCTET STRING Size(1..10)  

PrvtTwampTestEntry  
SEQUENCE    
  prvtTwampTestName PrvtTwampTestNameType
  prvtTwampTestRowStatus RowStatus
  prvtTwampTestServer IpAddress
  prvtTwampTestSessionsCount Integer32
  prvtTwampTestPackets Integer32
  prvtTwampTestTimeout Integer32
  prvtTwampTestDelay Integer32
  prvtTwampTestExecuteNow Integer32

PrvtTwampClientEntry  
SEQUENCE    
  prvtTwampClientIp IpAddress
  prvtTwampClientRowStatus RowStatus

PrvtTwampTestResultEntry  
SEQUENCE    
  prvtTwampTestId Unsigned32
  prvtTwampTestResultName PrvtTwampTestNameType
  prvtTwampTestStartTime Unsigned32
  prvtTwampTestServerAddress IpAddress
  prvtTwampTestSessions Unsigned32
  prvtTwampTestState INTEGER
  prvtTwampTestRtt Counter64
  prvtTwampTestMinRtt Counter64
  prvtTwampTestMaxRtt Counter64
  prvtTwampTestPcktSent Unsigned32
  prvtTwampTestPcktLost Unsigned32
  prvtTwampTestPcktDrop Unsigned32
  prvtTwampTestVariation Counter64
  prvtTwampTestVariationLow PrvtTwampDecimalPercent
  prvtTwampTestVariationMiddle PrvtTwampDecimalPercent
  prvtTwampTestVariationHigh PrvtTwampDecimalPercent

Defined Values

prvtSaaMib 1.3.6.1.4.1.738.1.5.130
This MIB provides the extended capability of controlling and provisioning various OAM tests and SAA monitoring. It adds extra functionality for DISMAN-PING-MIB
MODULE-IDENTITY    

prvtSaaNotifications 1.3.6.1.4.1.738.1.5.130.0
OBJECT IDENTIFIER    

prvtSaaObjects 1.3.6.1.4.1.738.1.5.130.1
OBJECT IDENTIFIER    

prvtSaaConformance 1.3.6.1.4.1.738.1.5.130.2
OBJECT IDENTIFIER    

prvtSaaTest 1.3.6.1.4.1.738.1.5.130.1.1
OBJECT IDENTIFIER    

prvtSaaTestResult 1.3.6.1.4.1.738.1.5.130.1.2
OBJECT IDENTIFIER    

prvtSaaProfiles 1.3.6.1.4.1.738.1.5.130.1.3
OBJECT IDENTIFIER    

prvtSaaY1731PmTestTable 1.3.6.1.4.1.738.1.5.130.1.1.1
This table holds the configuration for a SAA Y1731 test
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PrvtSaaY1731PmTestEntry

prvtSaaY1731PmTestEntry 1.3.6.1.4.1.738.1.5.130.1.1.1.1
NONE
Status: current Access: not-accessible
OBJECT-TYPE    
  PrvtSaaY1731PmTestEntry  

prvtSaaY1731PmTestOwner 1.3.6.1.4.1.738.1.5.130.1.1.1.1.1
This string is used to describe the owner of the Y1731 Pm SAA test.
Status: current Access: not-accessible
OBJECT-TYPE    
  SnmpAdminString Size(0..32)  

prvtSaaY1731PmTestName 1.3.6.1.4.1.738.1.5.130.1.1.1.1.2
This string is used to describe the test name for the Y1731 Pm SAA test. It is also used as a test identifier.
Status: current Access: not-accessible
OBJECT-TYPE    
  SnmpAdminString Size(0..32)  

prvtSaaY1731PmTestType 1.3.6.1.4.1.738.1.5.130.1.1.1.1.3
SAA Y1731 Pm test type.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER frameloss(1), framedelayAndDelayvariation(2), framelossAndFramedelayAndDelayvariation(3)  

prvtSaaY1731PmTestExecStatus 1.3.6.1.4.1.738.1.5.130.1.1.1.1.4
SAA Y1731 Pm test execution status.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notRunning(1), running(2)  

prvtSaaY1731PmTestEncapType 1.3.6.1.4.1.738.1.5.130.1.1.1.1.5
SAA Y1731 Pm test encapsulation type. It can be either test over VLAN or test over Service. The value 1 is the default value representing that neither type is set.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), service(2), vlan(3)  

prvtSaaY1731PmTestEncapValue 1.3.6.1.4.1.738.1.5.130.1.1.1.1.6
The value of the defined SAA Y1731 Pm test encapsulation. It should be either the Vlan ID or the Service ID, depending on the type set in prvtSaaY1731PmTestEncapType.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..4294967295  

prvtSaaY1731PmTestUserPort 1.3.6.1.4.1.738.1.5.130.1.1.1.1.7
For SAA Y1731 Pm test, this leaf is used only in case the encapsulation is VLAN type and it determines the port on which the user is connected.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

prvtSaaY1731PmTestUplinkPort 1.3.6.1.4.1.738.1.5.130.1.1.1.1.8
For SAA Y1731 Pm test, this leaf is used only in case the encapsulation is VLAN type and it determines the port that the SAA test devices are connected through.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

prvtSaaY1731PmTestTargetMac 1.3.6.1.4.1.738.1.5.130.1.1.1.1.9
The target MAC address for the SAA Y1731 test.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(17)  

prvtSaaY1731PmTestCfmDomainLevel 1.3.6.1.4.1.738.1.5.130.1.1.1.1.10
CFM Domain level on which the test will be run.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..7  

prvtSaaY1731PmTestRemoteCfmMep 1.3.6.1.4.1.738.1.5.130.1.1.1.1.11
The remote MEP associated with target MAC.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..8191  

prvtSaaY1731PmTestProfile 1.3.6.1.4.1.738.1.5.130.1.1.1.1.12
The profile ID associated to the SAA Y1731 Pm test. A value of 0 depicts no set profile.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0 | 1..2147483647  

prvtSaaY1731PmTestHistoryDepth 1.3.6.1.4.1.738.1.5.130.1.1.1.1.13
Probe history count.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..120  

prvtSaaY1731PmTestPeriod 1.3.6.1.4.1.738.1.5.130.1.1.1.1.14
The period the SAA Y1731 Pm test will run, in milliseconds.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 100..10000  

prvtSaaY1731PmTestTimeout 1.3.6.1.4.1.738.1.5.130.1.1.1.1.15
The timeout period for a test packet.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..60  

prvtSaaY1731PmTestMonitorInterval 1.3.6.1.4.1.738.1.5.130.1.1.1.1.16
Monitoring interval is relevant only for continous Y1731 test. It is measured in minutes.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..60  

prvtSaaY1731PmTestFrequency 1.3.6.1.4.1.738.1.5.130.1.1.1.1.17
The time between two consecutive intervals. A value of 1 defines a delay of a second between the end of the first and the begining of the next interval.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..65535  

prvtSaaY1731PmTestClocksInSync 1.3.6.1.4.1.738.1.5.130.1.1.1.1.18
This variable tells if the clocks of the test are syncronized.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

prvtSaaY1731PmTestDelayMethod 1.3.6.1.4.1.738.1.5.130.1.1.1.1.19
Defines the method of calculating delay on a Y1731 test.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER average(1), percentile(2)  

prvtSaaY1731PmTestDelayPvalue 1.3.6.1.4.1.738.1.5.130.1.1.1.1.20
Percent used to calculate delay in p-percentile method. Reported delay is the percent-th member in the array with sorted delays. Relevant only for p-percentile method. Value in range of 1-100 is for percentile delay method of calculation. Value 101 describes that average delay method of calculation is used. Only values inside the 1..100 range can be set to this parameter.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..100  

prvtSaaY1731PmTestJitterMethod 1.3.6.1.4.1.738.1.5.130.1.1.1.1.21
Defines the method of calculating jitter on a Y1731 test.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER peakToPeak(1), variance(2), percentile(3)  

prvtSaaY1731PmTestJitterPvalue 1.3.6.1.4.1.738.1.5.130.1.1.1.1.22
Percent used to calculate jitter in p-percentile method. Reported jitter is the percent-th member in the array with sorted jitters. Relevant only for p-percentile method. Value in range of 1..100 is for percentile jitter method of calculation. Value 101 describes that peakToPeak jitter method of calculation is used. Value 102 describes that variance jitter method of calculation is used. Only values inside the 1..100 range can be set to this parameter.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..100  

prvtSaaY1731PmTestPriority 1.3.6.1.4.1.738.1.5.130.1.1.1.1.23
Defines the priority of the packets sent by the SAA Y1731 Pm test (priority to count user traffic).
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..7  

prvtSaaY1731PmTestRowStatus 1.3.6.1.4.1.738.1.5.130.1.1.1.1.24
The status of the row. The writable columns in a row can not be changed if the row is active. Certain columns must have a valid value before a row can be activated.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

prvtSaaY1731PmTestCCMAPSCount 1.3.6.1.4.1.738.1.5.130.1.1.1.1.25
Determines whether to include proactive OAM frames for ETH-CC and ETH-APS in loss measurement counters or not.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

prvtSaaY1731PmTestLossMeasurementType 1.3.6.1.4.1.738.1.5.130.1.1.1.1.26
If set to 1 Synthetic Loss Measurement will be used for frame-loss calculations.If set 0 user packets will be used for frame-loss calculations
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER lmm(0), slm(1)  

prvtSaaY1731PmTestSLMTransmit 1.3.6.1.4.1.738.1.5.130.1.1.1.1.27
If set true the device is capable of sending SLM packets and frame-loss calculations. This must be used only when loss measurement type is SLM
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

prvtSaaY1731PmTestTestId 1.3.6.1.4.1.738.1.5.130.1.1.1.1.28
Specify the unique test id used in Y1731 SLM. 0 means not set.It is mandatory for the Y1731 SLM test
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..4095  

prvtSaaY1731PmTestDropEligible 1.3.6.1.4.1.738.1.5.130.1.1.1.1.29
Drop Eligible flag for S-VLAN used for the Y1731 SLM test.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

prvtSaaY1731PmTestDataSize 1.3.6.1.4.1.738.1.5.130.1.1.1.1.30
Packet sizes for Y1731 SLM test
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 64..1518  

prvtSaaY1731PmTestCountAllPriorities 1.3.6.1.4.1.738.1.5.130.1.1.1.1.31
Measure for all priorities.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

prvtSaaRFC2544ThroughputTestTable 1.3.6.1.4.1.738.1.5.130.1.1.2
This table holds the configuration for a SAA RFC2544 test
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PrvtSaaRFC2544ThroughputTestEntry

prvtSaaRFC2544ThroughputTestEntry 1.3.6.1.4.1.738.1.5.130.1.1.2.1
NONE
Status: current Access: not-accessible
OBJECT-TYPE    
  PrvtSaaRFC2544ThroughputTestEntry  

prvtSaaRFC2544ThroughputTestOwner 1.3.6.1.4.1.738.1.5.130.1.1.2.1.1
This string is used to describe the owner of the RFC2544 SAA test.
Status: current Access: not-accessible
OBJECT-TYPE    
  SnmpAdminString Size(0..32)  

prvtSaaRFC2544ThroughputTestName 1.3.6.1.4.1.738.1.5.130.1.1.2.1.2
This string is used to describe the test name for the RFC2544 SAA test. It is also used as a test identifier.
Status: current Access: not-accessible
OBJECT-TYPE    
  SnmpAdminString Size(0..32)  

prvtSaaRFC2544ThroughputTestType 1.3.6.1.4.1.738.1.5.130.1.1.2.1.3
SAA RFC2544 Throughput test type
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER unidirectionalTestHead(1), bidirectionalTestHead(2), testTail(3), testLoopback(4)  

prvtSaaRFC2544ThroughputTestExecStatus 1.3.6.1.4.1.738.1.5.130.1.1.2.1.4
SAA RFC2544 Throughput test execution status.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notRunning(1), running(2)  

prvtSaaRFC2544ThroughputTestSourceType 1.3.6.1.4.1.738.1.5.130.1.1.2.1.5
SAA RFC2544 Throughput test source type.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), mac(1), mep(2)  

prvtSaaRFC2544ThroughputTestSource 1.3.6.1.4.1.738.1.5.130.1.1.2.1.6
String that holds either the MAC or the MEP ID. MAC should be in the format AA:BB:CC:DD:EE:FF MEP shold be in the format DOMAIN:MA:MEP that represent the values corresponding to dot1agCfmMdIndex, dot1agCfmMaIndex and dot1agCfmMepIdentifier from IEEE8021-CFM-MIB. e.g.: MAC: 00:A0:12:5C:12:C0 MEP: 1:1:2
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(1..17)  

prvtSaaRFC2544ThroughputTestTargetType 1.3.6.1.4.1.738.1.5.130.1.1.2.1.7
SAA RFC2544 Throughput test target type.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), mac(1), mep(2)  

prvtSaaRFC2544ThroughputTestTarget 1.3.6.1.4.1.738.1.5.130.1.1.2.1.8
String that holds either the MAC or the MEP ID. MAC should be in the format AA:BB:CC:DD:EE:FF MEP shold be in the format DOMAIN:MA:MEP that represent the values corresponding to dot1agCfmMdIndex, dot1agCfmMaIndex and dot1agCfmMepIdentifier from IEEE8021-CFM-MIB. e.g.: MAC: 00:A0:12:5C:12:C0 MEP: 1:1:2
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(1..17)  

prvtSaaRFC2544ThroughputTestTimeout 1.3.6.1.4.1.738.1.5.130.1.1.2.1.9
SAA RFC2544 Throughput test timeout, in 0.1 of a second increments
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..100  

prvtSaaRFC2544ThroughputTestCIR 1.3.6.1.4.1.738.1.5.130.1.1.2.1.10
SAA RFC2544 Throughput Committed Information Rate (CIR) value.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 64..1000000  

prvtSaaRFC2544ThroughputTestCBS 1.3.6.1.4.1.738.1.5.130.1.1.2.1.11
SAA RFC2544 Throughput Committed Burst Size (CBS) value.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 10..2048  

prvtSaaRFC2544ThroughputTestBurstPercentage 1.3.6.1.4.1.738.1.5.130.1.1.2.1.12
Part of CIR to use for bursts(CBS).
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..100  

prvtSaaRFC2544ThroughputTestDuration 1.3.6.1.4.1.738.1.5.130.1.1.2.1.13
The SAA RFC2544 Throughput test duration, in seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..180  

prvtSaaRFC2544ThroughputTestMaxFrameloss 1.3.6.1.4.1.738.1.5.130.1.1.2.1.14
The maximum frameloss to declare a successful SAA RFC2544 Throughput test in 0.001 of a percent.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..100000  

prvtSaaRFC2544ThroughputTestCVLAN0 1.3.6.1.4.1.738.1.5.130.1.1.2.1.15
C-VLAN ID for the SAA RFC2544 Throughput test.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..4094  

prvtSaaRFC2544ThroughputTestCVLAN0Priority 1.3.6.1.4.1.738.1.5.130.1.1.2.1.16
VPT for C-VLAN0 for the SAA RFC2544 Throughput test.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..7  

prvtSaaRFC2544ThroughputTestCVLAN0DropEligible 1.3.6.1.4.1.738.1.5.130.1.1.2.1.17
Drop Eligible flag for C-VLAN0 for the SAA RFC2544 Throughput test.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

prvtSaaRFC2544ThroughputTestSVLAN 1.3.6.1.4.1.738.1.5.130.1.1.2.1.18
S-VLAN ID for the SAA RFC2544 Throughput test.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4094  

prvtSaaRFC2544ThroughputTestSVLANPriority 1.3.6.1.4.1.738.1.5.130.1.1.2.1.19
VPT for S-VLAN0 for the SAA RFC2544 Throughput test.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..7  

prvtSaaRFC2544ThroughputTestSVLANDropEligible 1.3.6.1.4.1.738.1.5.130.1.1.2.1.20
Drop Eligible flag for S-VLAN0 for the SAA RFC2544 Throughput test.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

prvtSaaRFC2544ThroughputTestPDUSize 1.3.6.1.4.1.738.1.5.130.1.1.2.1.21
Bitmask with predefined packet sizes for SAA RFC2544 Throughput test: 64, 128, 256, 512, 1024, 1280, 1518, 1530, 2000, 9000 (LSB set=64...10th bit set =9000)
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(3)  

prvtSaaRFC2544ThroughputTestACKTimeout 1.3.6.1.4.1.738.1.5.130.1.1.2.1.22
Defines the timeout for a SAA RFC2544 Throughput test tail to send an ACK MCC.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..60  

prvtSaaRFC2544ThroughputTestLoopbackType 1.3.6.1.4.1.738.1.5.130.1.1.2.1.23
SAA RFC2544 Throughput test loopback type.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER macSwap(1), oam(2)  

prvtSaaRFC2544ThroughputTestPaternType 1.3.6.1.4.1.738.1.5.130.1.1.2.1.24
SAA RFC2544 Throughput test patern type. Options for it are none, null, null-crc, prbs, prbs-crc.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER null(1), nullCRC(2), prbs(3), prbsCRC(4), none(8)  

prvtSaaRFC2544ThroughputTestRowStatus 1.3.6.1.4.1.738.1.5.130.1.1.2.1.25
The status of the row entry. The writable columns in a row can not be changed if the row is active. Certain columns must have a valid value before a row can be activated.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

prvtSaaRFC2544ThroughputTestEthertype 1.3.6.1.4.1.738.1.5.130.1.1.2.1.26
SAA RFC2544 Throughput test Ethertype.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

prvtSaaY1731LoopbackTestTable 1.3.6.1.4.1.738.1.5.130.1.1.3
This table holds the configuration for a SAA Y1731 Loopback test. It describes the FPGA configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PrvtSaaY1731LoopbackTestEntry

prvtSaaY1731LoopbackTestEntry 1.3.6.1.4.1.738.1.5.130.1.1.3.1
NONE
Status: current Access: not-accessible
OBJECT-TYPE    
  PrvtSaaY1731LoopbackTestEntry  

prvtSaaY1731LoopbackTestEncapType 1.3.6.1.4.1.738.1.5.130.1.1.3.1.1
SAA Y1731 Loopback test encapsulation type. It can be either test over VLAN or test over Service. The value 1 is the default value representing that neither type is set.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER service(1), vlan(2)  

prvtSaaY1731LoopbackTestEncapValue 1.3.6.1.4.1.738.1.5.130.1.1.3.1.2
The value of the defined SAA Y1731 Lopback test encapsulation. It should be either the Vlan ID or the Service ID, depending on the type set in prvtSaaY1731LoopbackTestEncapType.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 0..10000  

prvtSaaY1731LoopbackTestUserPort 1.3.6.1.4.1.738.1.5.130.1.1.3.1.3
For SAA Y1731 Loopback test, this leaf is used only in case the encapsulation is VLAN type and it determines the port on which the user is connected.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

prvtSaaY1731LoopbackTestUplinkPort 1.3.6.1.4.1.738.1.5.130.1.1.3.1.4
For SAA Y1731 Loopback test, this leaf is used only in case the encapsulation is VLAN type and it determines the port that the SAA test devices are connected through.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

prvtSaaY1731LoopbackTestType 1.3.6.1.4.1.738.1.5.130.1.1.3.1.5
SAA Y1731 Loopback test type. Specifies the test being perfoer
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), frameloss(2), delayvariation(3), framelossAndDelayvariation(4)  

prvtSaaY1731LoopbackTestRowStatus 1.3.6.1.4.1.738.1.5.130.1.1.3.1.6
The status of the row entry. The writable columns in a row can not be changed if the row is active. Certain columns must have a valid value before a row can be activated.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

prvtSaaY1731LoopbackTestCCMAPSCount 1.3.6.1.4.1.738.1.5.130.1.1.3.1.7
Determines whether to include proactive OAM frames for ETH-CC and ETH-APS in loss measurement counters or not.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

prvtSaaY1731LoopbackTestCountAllPriorities 1.3.6.1.4.1.738.1.5.130.1.1.3.1.8
Determines whether to count all packets ignoring the priority.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

prvtSaaY1731TestResultTable 1.3.6.1.4.1.738.1.5.130.1.2.1
This table contains SAA results for Y1731 tests.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PrvtSaaY1731TestResultEntry

prvtSaaY1731TestResultEntry 1.3.6.1.4.1.738.1.5.130.1.2.1.1
NONE
Status: current Access: not-accessible
OBJECT-TYPE    
  PrvtSaaY1731TestResultEntry  

prvtSaaY1731TestResultIndex 1.3.6.1.4.1.738.1.5.130.1.2.1.1.1
SAA Y1731 test results table index
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

prvtSaaY1731TestResultDelayNE 1.3.6.1.4.1.738.1.5.130.1.2.1.1.2
Near end delay result in 0.01 of a microsecond
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

prvtSaaY1731TestResultDelayFE 1.3.6.1.4.1.738.1.5.130.1.2.1.1.3
Far end delay result in 0.01 of a microsecond
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

prvtSaaY1731TestResultJitterNE 1.3.6.1.4.1.738.1.5.130.1.2.1.1.4
Near end jitter result in 0.01 of a microsecond
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

prvtSaaY1731TestResultJitterFE 1.3.6.1.4.1.738.1.5.130.1.2.1.1.5
Far end jitter result in 0.01 of a microsecond
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

prvtSaaY1731TestResultFrameLossNE 1.3.6.1.4.1.738.1.5.130.1.2.1.1.6
Near end frame-loss result in 0.0000001 of a percent
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

prvtSaaY1731TestResultFrameLossFE 1.3.6.1.4.1.738.1.5.130.1.2.1.1.7
Far end frame-loss result in 0.0000001 of a percent
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

prvtSaaY1731TestResultFramesSentNE 1.3.6.1.4.1.738.1.5.130.1.2.1.1.8
Near end sent frames
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

prvtSaaY1731TestResultFramesSentFE 1.3.6.1.4.1.738.1.5.130.1.2.1.1.9
Far end sent frames
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

prvtSaaY1731TestResultFramesRcvdNE 1.3.6.1.4.1.738.1.5.130.1.2.1.1.10
Near end received frames
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

prvtSaaY1731TestResultFramesRcvdFE 1.3.6.1.4.1.738.1.5.130.1.2.1.1.11
Far end received frames
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

prvtSaaY1731TestResultPacketsSent 1.3.6.1.4.1.738.1.5.130.1.2.1.1.12
The test packets sent between devices
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

prvtSaaY1731TestResultNoTimeouts 1.3.6.1.4.1.738.1.5.130.1.2.1.1.13
Number of timeouts for the SAA Y1731 Pm test
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

prvtSaaY1731TestResultNoErrors 1.3.6.1.4.1.738.1.5.130.1.2.1.1.14
Number of errors for the SAA Y1731 Pm test
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

prvtSaaY1731TestResultCompletionTime 1.3.6.1.4.1.738.1.5.130.1.2.1.1.15
Completion time in seconds for the SAA Y1731 PM test.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

prvtSaaRFC2544TestResultTable 1.3.6.1.4.1.738.1.5.130.1.2.2
This table contains SAA results for RFC2544 tests.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PrvtSaaRFC2544TestResultEntry

prvtSaaRFC2544TestResultEntry 1.3.6.1.4.1.738.1.5.130.1.2.2.1
NONE
Status: current Access: not-accessible
OBJECT-TYPE    
  PrvtSaaRFC2544TestResultEntry  

prvtSaaRFC2544TestResultIndex 1.3.6.1.4.1.738.1.5.130.1.2.2.1.1
SAA RFC2544 Throughput test results table index. Index will take values 1 to 9, each value representing a frame size from this list: 64, 128, 256, 512, 1024, 1280, 1518, 2000, 9000. The leaf prvtSaaRFC2544TestResultFrameSize will present this value in a more user-friendly way.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

prvtSaaRFC2544TestResultFrameSize 1.3.6.1.4.1.738.1.5.130.1.2.2.1.2
Frame size of the SAA RFC2544 test. Possible values are: 64, 128, 256, 512, 1024, 1280, 1518, 2000, 9000
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

prvtSaaRFC2544TestResultFrameLoss 1.3.6.1.4.1.738.1.5.130.1.2.2.1.3
Frame loss of the SAA RFC2544 test measured in 0.001 of a percent
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

prvtSaaRFC2544TestResultThroughput 1.3.6.1.4.1.738.1.5.130.1.2.2.1.4
Throughput of the SAA RFC2544 test measured in Kbps
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

prvtSaaRFC2544TestResultNetThroughput 1.3.6.1.4.1.738.1.5.130.1.2.2.1.5
The actual throughput of the SAA RFC2544 test containing only user data. It is measured in Kbps.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

prvtSaaRFC2544TestResultStatus 1.3.6.1.4.1.738.1.5.130.1.2.2.1.6
Status of the SAA RFC2544 test
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notAvailable(1), ready(2), error(3)  

prvtSaaRFC2544TestResultDelayMinimum 1.3.6.1.4.1.738.1.5.130.1.2.2.1.7
Minimum delay for SAA RFC2544 test measured in 1/100th of a microsecond.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

prvtSaaRFC2544TestResultDelayAverage 1.3.6.1.4.1.738.1.5.130.1.2.2.1.8
Average delay for SAA RFC2544 test measured in 1/100th of a microsecond.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

prvtSaaRFC2544TestResultDelayMaximum 1.3.6.1.4.1.738.1.5.130.1.2.2.1.9
Maximum delay for SAA RFC2544 test measured in 1/100th of a microsecond.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

prvtSaaProfileTable 1.3.6.1.4.1.738.1.5.130.1.3.1
Table contains SAA thresholds.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PrvtSaaProfileEntry

prvtSaaProfileEntry 1.3.6.1.4.1.738.1.5.130.1.3.1.1
NONE
Status: current Access: not-accessible
OBJECT-TYPE    
  PrvtSaaProfileEntry  

prvtSaaProfileIndex 1.3.6.1.4.1.738.1.5.130.1.3.1.1.1
SAA profile table index.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..2147483647  

prvtSaaProfileDelayNE 1.3.6.1.4.1.738.1.5.130.1.3.1.1.2
Near end delay in microseconds
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..60000000  

prvtSaaProfileDelayFE 1.3.6.1.4.1.738.1.5.130.1.3.1.1.3
Far end delay in microseconds
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..60000000  

prvtSaaProfileJitterNE 1.3.6.1.4.1.738.1.5.130.1.3.1.1.4
Near end jitter in microseconds
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..60000000  

prvtSaaProfileJitterFE 1.3.6.1.4.1.738.1.5.130.1.3.1.1.5
Far end jitter in microseconds
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..60000000  

prvtSaaProfileFrameLossNE 1.3.6.1.4.1.738.1.5.130.1.3.1.1.6
Near end frame-loss measured in 0.001 of percent
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..100000  

prvtSaaProfileFrameLossFE 1.3.6.1.4.1.738.1.5.130.1.3.1.1.7
Far end frame-loss measured in 0.001 of percent
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..100000  

prvtSaaProfileRowStatus 1.3.6.1.4.1.738.1.5.130.1.3.1.1.8
Creation/delete/edit of the SAA profile.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

prvtSaaProfileName 1.3.6.1.4.1.738.1.5.130.1.3.1.1.9
Name assigned to the SAA profile.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

prvtSaaRFC2544ProbeFailed 1.3.6.1.4.1.738.1.5.130.0.1
This trap should be sent whenever a SAA probe on a specific test fails.
Status: current Access: read-create
NOTIFICATION-TYPE    

prvtSaaRFC2544ProbeSuccess 1.3.6.1.4.1.738.1.5.130.0.2
This trap should be sent whenever a SAA probe on a specific test finishes with success.
Status: current Access: read-create
NOTIFICATION-TYPE    

prvtSaaRFC2544TestFinished 1.3.6.1.4.1.738.1.5.130.0.3
This trap should be sent whenever a SAA RFC2544 test is finished
Status: current Access: read-create
NOTIFICATION-TYPE    

prvtSaaY1731DelayNEThreshold 1.3.6.1.4.1.738.1.5.130.0.4
This trap should be sent whenever the near end delay on a SAA Y1731 test will surpass one of the 2 defined thresholds.
Status: current Access: read-create
NOTIFICATION-TYPE    

prvtSaaY1731DelayFEThreshold 1.3.6.1.4.1.738.1.5.130.0.5
This trap should be sent whenever the far end delay on a SAA Y1731 test will surpass one of the 2 defined thresholds.
Status: current Access: read-create
NOTIFICATION-TYPE    

prvtSaaY1731JitterNEThreshold 1.3.6.1.4.1.738.1.5.130.0.6
This trap should be sent whenever the near end jitter on a SAA Y1731 test will surpass one of the 2 defined thresholds.
Status: current Access: read-create
NOTIFICATION-TYPE    

prvtSaaY1731JitterFEThreshold 1.3.6.1.4.1.738.1.5.130.0.7
This trap should be sent whenever the far end jitter on a SAA Y1731 test will surpass one of the 2 defined thresholds.
Status: current Access: read-create
NOTIFICATION-TYPE    

prvtSaaY1731FrLossNEThreshold 1.3.6.1.4.1.738.1.5.130.0.8
This trap should be sent whenever the near end frameloss on a SAA Y1731 test will surpass one of the 2 defined thresholds.
Status: current Access: read-create
NOTIFICATION-TYPE    

prvtSaaY1731FrLossFEThreshold 1.3.6.1.4.1.738.1.5.130.0.9
This trap should be sent whenever the far end frameloss on a SAA Y1731 test will surpass one of the 2 defined thresholds.
Status: current Access: read-create
NOTIFICATION-TYPE    

prvtSaaCompliances 1.3.6.1.4.1.738.1.5.130.2.1
OBJECT IDENTIFIER    

prvtSaaGroups 1.3.6.1.4.1.738.1.5.130.2.2
OBJECT IDENTIFIER    

prvtSaaY1731TestGroup 1.3.6.1.4.1.738.1.5.130.2.2.1
Objects for the SAA Y1731 test group.
Status: current Access: read-create
OBJECT-GROUP    

prvtSaaRFC2544TestGroup 1.3.6.1.4.1.738.1.5.130.2.2.2
Objects for the SAA RFC2544 test group.
Status: current Access: read-create
OBJECT-GROUP    

prvtSaaY1731TestResultsGroup 1.3.6.1.4.1.738.1.5.130.2.2.3
Objects for the SAA Y1731 test results group.
Status: current Access: read-create
OBJECT-GROUP    

prvtSaaRFC2544TestResultsGroup 1.3.6.1.4.1.738.1.5.130.2.2.4
Objects for the SAA RFC2544 test results group.
Status: current Access: read-create
OBJECT-GROUP    

prvtSaaProfilesGroup 1.3.6.1.4.1.738.1.5.130.2.2.5
Objects for the SAA profiles group.
Status: current Access: read-create
OBJECT-GROUP    

prvtSaaNotificationsGroup 1.3.6.1.4.1.738.1.5.130.2.2.6
Objects for the Notifications group.
Status: current Access: read-create
NOTIFICATION-GROUP    

prvtSaaY1731LoopbackTestGroup 1.3.6.1.4.1.738.1.5.130.2.2.7
Objects for the SAA Y1731 Loopback test group.
Status: current Access: read-create
OBJECT-GROUP    

prvtSaaCompliance 1.3.6.1.4.1.738.1.5.130.2.1.1
The compliance statement for support of the SAA MIB module.
Status: current Access: read-create
MODULE-COMPLIANCE    

prvtTwampObjects 1.3.6.1.4.1.738.1.5.130.1.4
OBJECT IDENTIFIER    

prvtTwampTest 1.3.6.1.4.1.738.1.5.130.1.4.1
OBJECT IDENTIFIER    

prvtTwampServer 1.3.6.1.4.1.738.1.5.130.1.4.2
OBJECT IDENTIFIER    

prvtTwampTestResult 1.3.6.1.4.1.738.1.5.130.1.4.3
OBJECT IDENTIFIER    

prvtTwampTestTable 1.3.6.1.4.1.738.1.5.130.1.4.1.1
Table contains TWAMP tests.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PrvtTwampTestEntry

prvtTwampTestEntry 1.3.6.1.4.1.738.1.5.130.1.4.1.1.1
Entry in prvtTwampTestTable
Status: current Access: not-accessible
OBJECT-TYPE    
  PrvtTwampTestEntry  

prvtTwampTestName 1.3.6.1.4.1.738.1.5.130.1.4.1.1.1.1
TWAMP test name.
Status: current Access: not-accessible
OBJECT-TYPE    
  PrvtTwampTestNameType  

prvtTwampTestRowStatus 1.3.6.1.4.1.738.1.5.130.1.4.1.1.1.2
Create/delete entry in prvtTwampTestTable.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

prvtTwampTestServer 1.3.6.1.4.1.738.1.5.130.1.4.1.1.1.3
TWAMP test server ip-address.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

prvtTwampTestSessionsCount 1.3.6.1.4.1.738.1.5.130.1.4.1.1.1.4
The number of parallel test sessions.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..10  

prvtTwampTestPackets 1.3.6.1.4.1.738.1.5.130.1.4.1.1.1.5
The number of packets in parallel sessions.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 10..1000  

prvtTwampTestTimeout 1.3.6.1.4.1.738.1.5.130.1.4.1.1.1.6
The timout interval of test packets (in milliseconds).
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 100..10000  

prvtTwampTestDelay 1.3.6.1.4.1.738.1.5.130.1.4.1.1.1.7
The delay interval between test packets (in milliseconds)
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 100..1500  

prvtTwampTestExecuteNow 1.3.6.1.4.1.738.1.5.130.1.4.1.1.1.8
When this object is set to '1', command self-test execute-now. When this object is set to '2' the self-test is stopped. Setting the variable to '0' results in an 'inconsistentValue' error. Setting it to any other value has no effect. When this object is read, the value '0' is returned.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..2  

prvtTwampClientTable 1.3.6.1.4.1.738.1.5.130.1.4.2.6
Table contains the allowed clients for the TWAMP server.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PrvtTwampClientEntry

prvtTwampClientEntry 1.3.6.1.4.1.738.1.5.130.1.4.2.6.1
Entry in twampClientTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  PrvtTwampClientEntry  

prvtTwampClientIp 1.3.6.1.4.1.738.1.5.130.1.4.2.6.1.1
The ip-address of the client.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

prvtTwampClientRowStatus 1.3.6.1.4.1.738.1.5.130.1.4.2.6.1.2
create/delete entry in prvtTwampClientTable
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

prvtTwampServerInnactivity 1.3.6.1.4.1.738.1.5.130.1.4.2.1
The server innactivity timeout interval of the TWAMP server (in seconds).
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..900  

prvtTwampServerSessionInnactivity 1.3.6.1.4.1.738.1.5.130.1.4.2.2
The session innactivity timeout interval of the TWAMP server (in seconds).
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..900  

prvtTwampServerMaxSessions 1.3.6.1.4.1.738.1.5.130.1.4.2.3
The maximum number of controll sessions supported by the TWAMP server.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..1000  

prvtTwampServerMaxParallelSessions 1.3.6.1.4.1.738.1.5.130.1.4.2.4
The maximum number of parallel test sessions for each client supperted by the TWAMP server.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..10  

prvtTwampServerShutdown 1.3.6.1.4.1.738.1.5.130.1.4.2.5
The administrative state of the TWAMP server.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

prvtTwampServerControlSessions 1.3.6.1.4.1.738.1.5.130.1.4.2.7
The number of current control sessions established on the TWAMP server.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

prvtTwampServerTestSessions 1.3.6.1.4.1.738.1.5.130.1.4.2.8
The number of current test sessions established on the TWAMP server.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

prvtTwampTestResultTable 1.3.6.1.4.1.738.1.5.130.1.4.3.1
Table contains statistics of the executed TWAMP tests.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PrvtTwampTestResultEntry

prvtTwampTestResultEntry 1.3.6.1.4.1.738.1.5.130.1.4.3.1.1
Entry in twampTestResultTable
Status: current Access: not-accessible
OBJECT-TYPE    
  PrvtTwampTestResultEntry  

prvtTwampTestId 1.3.6.1.4.1.738.1.5.130.1.4.3.1.1.1
The internal ID of the TWAMP test instance.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

prvtTwampTestResultName 1.3.6.1.4.1.738.1.5.130.1.4.3.1.1.2
TWAMP test name.
Status: current Access: read-only
OBJECT-TYPE    
  PrvtTwampTestNameType  

prvtTwampTestStartTime 1.3.6.1.4.1.738.1.5.130.1.4.3.1.1.3
The start time of the TWAMP test instance.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

prvtTwampTestServerAddress 1.3.6.1.4.1.738.1.5.130.1.4.3.1.1.4
The server ip-address of the TWAMP test instance.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

prvtTwampTestSessions 1.3.6.1.4.1.738.1.5.130.1.4.3.1.1.5
The number of parallel test sessions of the TWAMP test instance.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

prvtTwampTestState 1.3.6.1.4.1.738.1.5.130.1.4.3.1.1.6
The status of the executed TWAMP test instance.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER failed(1), running(2), stopped(3), finished(4)  

prvtTwampTestRtt 1.3.6.1.4.1.738.1.5.130.1.4.3.1.1.7
The average round-trip time of the TWAMP test sample.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

prvtTwampTestMinRtt 1.3.6.1.4.1.738.1.5.130.1.4.3.1.1.8
The minimum round-trip time of the TWAMP test sample.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

prvtTwampTestMaxRtt 1.3.6.1.4.1.738.1.5.130.1.4.3.1.1.9
The maximum round-trip time of the TWAMP test sample.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

prvtTwampTestPcktSent 1.3.6.1.4.1.738.1.5.130.1.4.3.1.1.10
The number of test packets sent for the TWAMP test instance.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

prvtTwampTestPcktLost 1.3.6.1.4.1.738.1.5.130.1.4.3.1.1.11
The number of lost test packets.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

prvtTwampTestPcktDrop 1.3.6.1.4.1.738.1.5.130.1.4.3.1.1.12
The number of dropped test packets.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

prvtTwampTestVariation 1.3.6.1.4.1.738.1.5.130.1.4.3.1.1.13
The maximum module variation of the TWAMP test sample
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

prvtTwampTestVariationLow 1.3.6.1.4.1.738.1.5.130.1.4.3.1.1.14
The percent of singletons whose variation is less than 10% of the negated maximum module variation of the sample.
Status: current Access: read-only
OBJECT-TYPE    
  PrvtTwampDecimalPercent  

prvtTwampTestVariationMiddle 1.3.6.1.4.1.738.1.5.130.1.4.3.1.1.15
The percent of singletons whose variation by module is less than 10% of the maximum module variation of the sample.
Status: current Access: read-only
OBJECT-TYPE    
  PrvtTwampDecimalPercent  

prvtTwampTestVariationHigh 1.3.6.1.4.1.738.1.5.130.1.4.3.1.1.16
The percent of singletons whose variation is greater than 10% of the maximum module variation of the sample.
Status: current Access: read-only
OBJECT-TYPE    
  PrvtTwampDecimalPercent