PRVT-RSVP-MIB

File: PRVT-RSVP-MIB.mib (72006 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-CONF	SNMPv2-TC
IF-MIB	INET-ADDRESS-MIB	PRVT-CR-LDP-MIB

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	Integer32
Unsigned32	IpAddress	MODULE-COMPLIANCE
OBJECT-GROUP	TEXTUAL-CONVENTION	RowStatus
TruthValue	InterfaceIndexOrZero	InetAddressIPv6
mpls

Defined Types

PrvtRsvpAdminStatus
The desired administrative state of an RSVP entity.
TEXTUAL-CONVENTION
	INTEGER	up(1), down(2)

PrvtRsvpOperStatus
The current operational state of an RSVP entity.
TEXTUAL-CONVENTION
	INTEGER	up(1), down(2), goingUp(3), goingDown(4), actFailed(5)

PrvtRsvpIndex
The index value identifying an RSVP entity.
TEXTUAL-CONVENTION
	Unsigned32

PrvtRsvpDiagReqIndex
The index value identifying an RSVP session that is being diagnosed.
TEXTUAL-CONVENTION
	Unsigned32

PrvtRsvpDiagNodeIndexType
The index value identifying a node within an RSVP session that is being diagnosed.
TEXTUAL-CONVENTION
	Unsigned32

PrvtRsvpDiagNodeTypeVal
The type of a node in a session that is being diagnosed.
TEXTUAL-CONVENTION
	INTEGER	missing(1), ingress(2), transit(3), egress(4)

PrvtRsvpProductEntry
SEQUENCE
	prvtRsvpProductIndex	PrvtRsvpIndex
	prvtRsvpProductASNumber	Integer32
	prvtRsvpProductSenderTTL	Integer32
	prvtRsvpProductMinTimerPeriod	Integer32
	prvtRsvpProductAPIIfIndex	InterfaceIndexOrZero
	prvtRsvpProductAPIAddress	OCTET STRING
	prvtRsvpProductAPIRefreshInterval	Integer32
	prvtRsvpProductLocalRepairDelay	Integer32
	prvtRsvpProductRefreshInterval	Integer32
	prvtRsvpProductRefreshMultiple	Integer32
	prvtRsvpProductRfrshSlewDenom	Integer32
	prvtRsvpProductRfrshSlewNumerator	Integer32
	prvtRsvpProductBlockadeMultiple	Integer32
	prvtRsvpProductSocketBufPoolSize	Integer32
	prvtRsvpProductSwitchBufPoolSize	Integer32
	prvtRsvpProductTeMibBufPoolSize	Integer32
	prvtRsvpProductRoutingBufPoolSize	Integer32
	prvtRsvpProductLSPSetupPriority	Integer32
	prvtRsvpProductLSPHoldingPriority	Integer32
	prvtRsvpProductAdminStatus	PrvtRsvpAdminStatus
	prvtRsvpProductOperStatus	PrvtRsvpOperStatus
	prvtRsvpProductRowStatus	RowStatus
	prvtRsvpProductLsrIndex	Unsigned32
	prvtRsvpProductTeMibIndex	Unsigned32
	prvtRsvpProductMultiStackSupport	Integer32
	prvtRsvpProductUseHopByHop	TruthValue
	prvtRsvpProductUseNotify	TruthValue
	prvtRsvpProductNotifyRRDecay	Integer32
	prvtRsvpProductNotifyRRInterval	Integer32
	prvtRsvpProductNotifyRRLimit	Integer32
	prvtRsvpProductAllowIPEncap	TruthValue
	prvtRsvpProductProtocolExtensions	BITS
	prvtRsvpProductPSRFlags	BITS
	prvtRsvpProductInitPathRRDecay	Integer32
	prvtRsvpProductInitPathRRInterval	Integer32
	prvtRsvpProductInitPathRRLimit	Integer32
	prvtRsvpProductEnableUni	TruthValue
	prvtRsvpProductRestartCapable	TruthValue
	prvtRsvpProductRestartTime	Unsigned32
	prvtRsvpProductRecoveryTime	Unsigned32
	prvtRsvpProductMinPeerRestart	Integer32
	prvtRsvpProductGracefulDelTimeout	Integer32
	prvtRsvpProductEgressDelBehavior	INTEGER
	prvtRsvpProductEnabUniConnSplicing	TruthValue
	prvtRsvpProductFastRerouteCaps	BITS
	prvtRsvpProductFastRroutBkpRtryInt	Integer32
	prvtRsvpProductErrorActionFlags	BITS
	prvtRsvpProductEnableNni	INTEGER
	prvtRsvpProductBehaviorFlags	BITS
	prvtRsvpProductLabelSetStyle	INTEGER
	prvtRsvpProductLabelSetOperStatus	INTEGER
	prvtRsvpProductLabelSetTrapEnable	TruthValue
	prvtRsvpProductLabelSetChngAct	Integer32
	prvtRsvpProductExtPrtAdminStatus	PrvtRsvpAdminStatus
	prvtRsvpProductUniIncSonetProfile	Unsigned32
	prvtRsvpProductFrrFacAdminStatus	PrvtRsvpAdminStatus
	prvtRsvpProductFrrFacOperStatus	PrvtRsvpOperStatus
	prvtRsvpProductIpv6AdminStatus	PrvtRsvpAdminStatus
	prvtRsvpProductIpv6OperStatus	PrvtRsvpOperStatus
	prvtRsvpProductAPIIpv6Address	InetAddressIPv6

PrvtRsvpDiagnosticEntry
SEQUENCE
	prvtRsvpDiagProductIndex	PrvtRsvpIndex
	prvtRsvpDiagRequestIndex	PrvtRsvpDiagReqIndex
	prvtRsvpDiagReqsInProgress	Unsigned32
	prvtRsvpDiagSessionEndPoint	IpAddress
	prvtRsvpDiagSessionTunnelId	Unsigned32
	prvtRsvpDiagSessionExtTunnelId	Unsigned32
	prvtRsvpDiagLastHop	IpAddress
	prvtRsvpDiagSender	IpAddress
	prvtRsvpDiagMaxHops	Integer32
	prvtRsvpDiagHopByHopReply	TruthValue

PrvtRsvpDiagNodeEntry
SEQUENCE
	prvtRsvpDiagNodeProductIndex	PrvtRsvpIndex
	prvtRsvpDiagNodeRequestIndex	PrvtRsvpDiagReqIndex
	prvtRsvpDiagNodeIndex	PrvtRsvpDiagNodeIndexType
	prvtRsvpDiagNodeType	PrvtRsvpDiagNodeTypeVal
	prvtRsvpDiagNodeDreqArrivalTime	Unsigned32
	prvtRsvpDiagNodeIncomingIfAddr	IpAddress
	prvtRsvpDiagNodeOutgoingIfAddr	IpAddress
	prvtRsvpDiagNodePrevHopAddr	IpAddress
	prvtRsvpDiagNodeDTTL	Integer32
	prvtRsvpDiagNodeMFlag	TruthValue
	prvtRsvpDiagNodeRErr	Integer32
	prvtRsvpDiagNodeKValue	Integer32
	prvtRsvpDiagNodeTimerValue	Integer32
	prvtRsvpDiagRsvpHopAddr	IpAddress
	prvtRsvpDiagRsvpHopLIH	Unsigned32
	prvtRsvpDiagSenderTpltAddress	IpAddress
	prvtRsvpDiagSenderTpltLSPId	Integer32
	prvtRsvpDiagFlowSpecCLBktRate	Unsigned32
	prvtRsvpDiagFlowSpecCLBktDep	Unsigned32
	prvtRsvpDiagFlowSpecCLPkDataRate	Unsigned32
	prvtRsvpDiagFlowSpecCLMinPolUnit	Unsigned32
	prvtRsvpDiagFlowSpecCLMaxPktSize	Unsigned32
	prvtRsvpDiagFlowSpecGQBktRate	Unsigned32
	prvtRsvpDiagFlowSpecGQBktDep	Unsigned32
	prvtRsvpDiagFlowSpecGQPkDataRate	Unsigned32
	prvtRsvpDiagFlowSpecGQMinPolUnit	Unsigned32
	prvtRsvpDiagFlowSpecGQMaxPktSize	Unsigned32
	prvtRsvpDiagFlowSpecGQRate	Unsigned32
	prvtRsvpDiagFlowSpecGQSlack	Unsigned32
	prvtRsvpDiagFlowSpecCoSCoS	Integer32
	prvtRsvpDiagFlowSpecCoSMTU	Integer32
	prvtRsvpDiagFilterSpecAddress	IpAddress
	prvtRsvpDiagFilterSpecLSPId	Integer32
	prvtRsvpDiagConfirmRcvAddr	IpAddress
	prvtRsvpDiagStyle	Unsigned32

Defined Values

prvtRsvp		78.5.7
The MIB module for management of the PRVT-RSVP product.
MODULE-IDENTITY

prvtRsvpObjects		78.5.7.1
OBJECT IDENTIFIER

prvtRsvpProductTable		78.5.7.1.1
The table of RSVP entities.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrvtRsvpProductEntry

prvtRsvpProductEntry		78.5.7.1.1.1
Each entry represents an RSVP entity.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrvtRsvpProductEntry

prvtRsvpProductIndex		78.5.7.1.1.1.1
The index of this prvtRsvpProductEntry. This is the HAF entity index passed on the entity create parameters.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrvtRsvpIndex

prvtRsvpProductASNumber		78.5.7.1.1.1.2
The number identifying the autonomous system (AS) to which this node belongs.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..65535

prvtRsvpProductSenderTTL		78.5.7.1.1.1.3
The TTL set on messages originating at this node. A value of 0 indicates this number is determined by other means.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..255

prvtRsvpProductMinTimerPeriod		78.5.7.1.1.1.4
The minimum granularity to allow an internal timer to be set in the PRVT-RSVP product code.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

prvtRsvpProductAPIIfIndex		78.5.7.1.1.1.5
Management assigned interface identifier for the (internal) LRAPI interface between RSVP and TE-MIB components. This must be unique in the interface index namespace of the node - it MUST not match any real interface index. It is recommended that this is set to zero or 0x7FFFFFFF.
Status: current	Access: read-create
OBJECT-TYPE
	InterfaceIndexOrZero

prvtRsvpProductAPIAddress		78.5.7.1.1.1.6
Management assigned IP address used to identify the (internal) LRAPI interface between RSVP and TE-MIB components. The configured API address MUST not be a real address in the network. It is recommended that this is set to a non-zero reserved address value, such as 224.0.0.0. If multi-stack support is set to PHOP, this address must be unique for each RSVP stack in the node. The same address(es) can be used on all nodes in the network.
Status: current	Access: read-create
OBJECT-TYPE
	OCTET STRING	Size(4..16)

prvtRsvpProductAPIRefreshInterval		78.5.7.1.1.1.7
This field is now deprecated.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

prvtRsvpProductLocalRepairDelay		78.5.7.1.1.1.8
This object is used to set the delay between detection of a path error and instigation of local repair procedures. This allows local routing updates to converge. A value of -1 indicates that local repair procedures should not take place, but that the error should be propagated upstream. Where FRR capabilities are supported at this node local_repair_delay must be set to -1.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	-1 \| 1000..2147483647

prvtRsvpProductRefreshInterval		78.5.7.1.1.1.9
This RSVP value, R, which is used to set the average interval between refresh path and resv messages. Note : If values for the if_refresh_interval and if_refresh_multiple are configured such that the following inequality is not obeyed : 6 * refresh_interval * (refresh_multiple + 0.5) < 0x7FFFFFFF. Then the time-to-die for the path value will be set to its maximum value and it is probable that the lsp will time out before a refresh arrives.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1000..2147483647

prvtRsvpProductRefreshMultiple		78.5.7.1.1.1.10
The RSVP value, K, which is the number of unresponded Path or Resv refresh attempts which must be made, spaced by the refresh interval before the state is deemed to have timed out. Note : See note in prvtRsvpProductRefreshInterval above.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..214783647

prvtRsvpProductRfrshSlewDenom		78.5.7.1.1.1.11
The denominator of the fraction, SlewMax, which is the maximum allowable increase in the refresh interval, R, to prevent state timeout while changing R. R is increased by this fraction until it reaches the new desired value.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..214783647

prvtRsvpProductRfrshSlewNumerator		78.5.7.1.1.1.12
The numerator of the fraction, SlewMax, which is the maximum allowable increase in the refresh interval, R, to prevent state timeout while changing R. R is increased by this fraction until it reaches the new desired value.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..214783647

prvtRsvpProductBlockadeMultiple		78.5.7.1.1.1.13
The RSVP value, Kb, which is the number of refresh timeout periods after which blockade state is deleted.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..214783647

prvtRsvpProductSocketBufPoolSize		78.5.7.1.1.1.14
The number of pre-reserved buffers available for sending sockets data. This is used to pace the sockets data flows.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

prvtRsvpProductSwitchBufPoolSize		78.5.7.1.1.1.15
The number of pre-reserved buffers available for programming the switch. This is used to ensure programming operations do not fail in buffer shortage conditions.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

prvtRsvpProductTeMibBufPoolSize		78.5.7.1.1.1.16
The number of pre-reserved buffers available for signalling TE-MIB. This is used to ensure signals are not lost in buffer shortage conditions.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

prvtRsvpProductRoutingBufPoolSize		78.5.7.1.1.1.17
The number of pre-reserved buffers available for route queries. This is used to ensure re-routing of many LSPs does not fail in buffer shortage conditions.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

prvtRsvpProductLSPSetupPriority		78.5.7.1.1.1.18
The setup priority to apply to LSPs which are not signalling this parameter. 0 represents the highest priority, 7 the lowest. The value of this object must be numerically more or equal (so lower or equal priority) than the value of the holding priority object.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..7

prvtRsvpProductLSPHoldingPriority		78.5.7.1.1.1.19
The holding priority to apply to LSPs which are not signalling this parameter. 0 represents the highest priority, 7 the lowest. The value of this object must be numerically less or equal (so higher or equal priority) than the value of the holding priority object.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..7

prvtRsvpProductAdminStatus		78.5.7.1.1.1.20
The desired administrative state of the RSVP entity.
Status: current	Access: read-create
OBJECT-TYPE
	PrvtRsvpAdminStatus

prvtRsvpProductOperStatus		78.5.7.1.1.1.21
The current operational state of this instance of PRVT-RSVP.
Status: current	Access: read-only
OBJECT-TYPE
	PrvtRsvpOperStatus

prvtRsvpProductRowStatus		78.5.7.1.1.1.22
Used to create and delete a PRVT-RSVP Product Table entry. When this object is set to 'active', only the prvtRsvpProductAdminStatus object in the row may be modified.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

prvtRsvpProductLsrIndex		78.5.7.1.1.1.23
The index of the PRVT-LMGR product instance which this PRVT-RSVP is to join to as its LDB interface provider. If this value is not specified, or the value of this object is 0, PRVT-RSVP will use the prvtRsvpProductIndex value as the Lsr index when joining on the LDB interface.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

prvtRsvpProductTeMibIndex		78.5.7.1.1.1.24
The index of the TE-MIB product instance which this PRVT-RSVP is to join to as its LRA interface provider. If this value is not specified, or the value of this object is 0, PRVT-RSVP will use the prvtRsvpProductIndex value as the TeMib Index when joining on the LRA interface.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

prvtRsvpProductMultiStackSupport		78.5.7.1.1.1.25
A flag to indicate if multiple RSVP stacks are present in the same system as the current one and, if so, how they are supported. If set to PHOP, Path messages are forwarded to PRVT-RSVP with the Previous Hop value set as the hop prior to the incoming interface, not as the next hop interface as normal. If set to LIH, the hardware location of the current RSVP stack is used as the LIH in the HOP object.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..3

prvtRsvpProductUseHopByHop		78.5.7.1.1.1.26
A flag to indicate that PRVT-RSVP should use the hop by hop addressing scheme for PATH and PATH-TEAR messages it sends. If set then the IP addresses used in the IP header of PATH messages forwarded by PRVT-RSVP set source as the local outgoing interface IP address, and destination as the next hop router IP address.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

prvtRsvpProductUseNotify		78.5.7.1.1.1.27
A flag to indicate that PRVT-RSVP should attempt to insert a Notify Request object in all Path requests that is sends as ingress and all Resv requests that it sends as egress. The precise behavior is modified by a user exit called by the RSVP code. This field is not used unless the mplsTunnelUpNotRecip or mplsTunnelDownNotRecip fields in TE-MIB are set to 0.0.0.0.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

prvtRsvpProductNotifyRRDecay		78.5.7.1.1.1.28
The percentage increase in the rapid retransmission interval for each consecutive unacknowledged RSVP Notify message. A value of 0 indicates a constant retransmission rate.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..100

prvtRsvpProductNotifyRRInterval		78.5.7.1.1.1.29
The interval in milliseconds before a Notify message is first resent if no acknowledgement is received.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1000..2147483647

prvtRsvpProductNotifyRRLimit		78.5.7.1.1.1.30
The maximum number of times a Notify message is resent if no acknowledgement is received.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..2147483647

prvtRsvpProductAllowIPEncap		78.5.7.1.1.1.31
A flag to indicate that PRVT-RSVP should support the use of IP encapsulation of RSVP packets, which are required for out-of-band signaling. If set, then PRVT-RSVP will accept incoming RSVP packets that are IP encapsulated, and will IP encapsulate outgoing packets whenever the IP routing stub indicates that it is required for a particular route.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

prvtRsvpProductProtocolExtensions		78.5.7.1.1.1.32
Specifies which extensions to the standard RSVP-TE protocol are enabled. For fully standards-compliant behavior, set this parameter to zero (no bits set). To enable specific non-standard protocol extensions, set this parameter to the bitwise OR of whichever of the following behaviors you wish to enable. - bypassFastReroute: Enable support for facility fast reroute protection of LSPs (bypass LSP protection). This flag is deprecated in favour of the prvtRsvpProductFrrFacAdminStatus field which can be modified while RSVP is admin up, however either field can be used. When this flag is set RSVP automatically sets the prvtRsvpProductFrrFacAdminStatus. - detourFastReroute: Enable support for one-to-one fast reroute protection of LSPs (detour LSP protection). - noResAffOnInIf: Disable resource affinity checking on incoming interfaces for LSPs. If this flag is set, RSVP will accept Path messages which use invalid resource affinities for the incoming interface used by the LSP.
Status: current	Access: read-create
OBJECT-TYPE
	BITS	bypassFastReroute(0), detourFastReroute(1), noResAffOnInIf(2)

prvtRsvpProductPSRFlags		78.5.7.1.1.1.33
This field is used by PRVT-RSVP to determine whether it should set the Path State Removed flag on a PathErr (and therefore remove corresponding state and generate a PathTear). Each bit of this flags field corresponds to a situation where PRVT-RSVP may generate a PathErr. Setting a particular bit will result in PRVT-RSVP removing state, setting the Path State Removed flag and generating a PathTear in that corresponding situation. The possible bit values are - pathErrPSRSet: PRVT-RSVP has received a PathErr message with the Path State Removed flag set. - pathErrPSRNotSet: PRVT-RSVP has received a PathErr message with the Path State Removed flag unset. - ldbCommonRcvd: PRVT-RSVP has received a negative response to an ATG_LDB_RESERVE_LSP_XC or ATG_LDB_CONNECT_LSP_XC message. - ldbPreempted: PRVT-RSVP has received a Preemption message from Label Manager. - routingError: PRVT-RSVP has received a Negative response to an ATG_IPR_QUERY_ROUTE message. - invalidPathMsg: PRVT-RSVP has received an invalid Path message. - sessionExpired: A session in PRVT-RSVP has expired. - unableToRepairRoute: A route has been removed and PRVT-RSVP is unable to start local repair. - unableToRepairIf: An interface has been removed and PRVT-RSVP is unable start local repair. - reachedRetryLimit: An initial Path Message has reached its retry limit. - unableToRefresh: PRVT-RSVP has been unable to refresh an LSP. - resvErrTurnaround: PRVT-RSVP has received a ResvErr at the Egress node containing a REROUTING object and this is to be turned round into a PathErr. - incomingIfDown: The incoming MPLS data interface for an LSP has been deactivated. - outgoingIfDown: The outgoing MPLS data interface for an LSP has been deactivated.
Status: current	Access: read-create
OBJECT-TYPE
	BITS	pathErrPSRSet(0), pathErrPSRNotSet(1), ldbCommonRcvd(2), ldbPreempted(3), routingError(4), invalidPathMsg(5), sessionExpired(6), unableToRepairRoute(7), unableToRepairIf(8), reachedRetryLimit(9), unableToRefresh(10), resvErrTurnaround(11), incomingIfDown(12), outgoingIfDown(13)

prvtRsvpProductInitPathRRDecay		78.5.7.1.1.1.34
The percentage increase in the rapid retransmission interval for each consecutive unacknowledged RSVP Initial Path message. A value of 0 indicates a constant retransmission rate. A Path message is treated as an initial Path if it is the Path message which creates the LSP or a Path refresh message which requires re-routing.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..100

prvtRsvpProductInitPathRRInterval		78.5.7.1.1.1.35
The rapid retransmission interval in milliseconds before an Initial Path message is first resent if no acknowledgement is received. A Path message is treated as an initial Path if it is the Path message which creates the LSP or a Path refresh message which requires re-routing.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1000..2147483647

prvtRsvpProductInitPathRRLimit		78.5.7.1.1.1.36
The maximum number of times an Initial Path message is resent if no acknowledgement is received. A Path message is treated as an initial Path if it is the Path message which creates the LSP or a Path refresh message which requires re-routing.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..2147483647

prvtRsvpProductEnableUni		78.5.7.1.1.1.37
A flag to indicate whether the local node supports UNI signaling messages.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

prvtRsvpProductRestartCapable		78.5.7.1.1.1.38
A flag to indicate whether the local node should advertise itself as restart capable. This should be set to true if fault-tolerance is enabled in PRVT-MPLS or if the node supports recovery procedures.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

prvtRsvpProductRestartTime		78.5.7.1.1.1.39
The time in milliseconds that the local node takes to restart RSVP-TE and the communication channel used for RSVP communication. This is advertised to neighbors in the Restart_Cap object in Hello messages. The value chosen should be large enough for RSVP to be terminated and restarted. If fault-tolerance is enabled in PRVT-MPLS, then sufficient time should be allowed for RSVP to fail over, which should include the time taken for the audit phase to complete. A value of 0xFFFFFFFF may be configured to imply an infinite restart time. Only used if prvtRsvpProductRestartCapable is set to true. Note that the maximum real time value that can be set is 0x7FFFFFFF. If a value is requested greater than 0x7FFFFFFF and less than 0xFFFFFFFF the request will be rejected.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

prvtRsvpProductRecoveryTime		78.5.7.1.1.1.40
The period of time in milliseconds that the local node would like neighbors to take to resyncronize RSVP and MPLS forwarding information after the re-establishment of Hello connectivity. This is advertised to neighbors in the Restart_Cap object in Hello messages. A value of zero indicates that the node does not support resynchronization following failure of the local node. A value of 0xFFFFFFFF indicates an infinite recovery time. Note that if fault-tolerance is not enabled in PRVT-MPLS and the node is acting as an ingress for tunnels, then any ingress tunnels that need to be recovered should be configured during this recovery period. These tunnels should be configured in TE-MIB with the admin_status set to UP, otherwise they will be lost from the switch controller. Only used if prvtRsvpProductRestartCapable is set to true. Note that the maximum real time value that can be set is 0x7FFFFFFF. If a value is requested greater than 0x7FFFFFFF and less than 0xFFFFFFFF the request will be rejected.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

prvtRsvpProductMinPeerRestart		78.5.7.1.1.1.41
The mininum period of time in milliseconds that RSVP should wait for a restart capable neighbor to regain Hello connectivity before invoking procedures related to communication loss. RSVP will wait for the maximum of this time and the restart_time advertised in the RESTART_CAP object in Hello messages from the neighbor.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

prvtRsvpProductGracefulDelTimeout		78.5.7.1.1.1.42
The time in milliseconds that PRVT-MPLS will wait for graceful deletion to complete before the forced deletion procedure is used instead.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

prvtRsvpProductEgressDelBehavior		78.5.7.1.1.1.43
Specifies the action that an egress node should take in the graceful deletion procedure on receipt of a Path message containing an Admin Status object with the D and R bits set. The possible values are:- - delWithPathErr: Send a PathErr message with the Path_State_removed flag set. - delWithResvD: Send a Resv message containing an Admin Status object with the D bit set.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	delWithPathErr(1), delWithResvD(2)

prvtRsvpProductEnabUniConnSplicing		78.5.7.1.1.1.44
A flag to indicate whether UNI-N nodes should allow the splicing of UNI connections with proprietary ON connections.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

prvtRsvpProductFastRerouteCaps		78.5.7.1.1.1.45
Specifies what fast reroute capabilities are enabled on this node. This field is only valid if the fast reroute extension is enabled in the prvtRsvpProductProtocolExtensions field above. - PLR: Node provides fast reroute point of local repair capability. - MP: Node provides fast reroute merge point capability. - DetourRestart: Node implements some protocol extensions to recover detour fast reroute LSPs after a node restart or an adjacent node restart. This flag is only valid if detourFastReroute flag is set in the prvtRsvpProductProtocolExtensions field above. Note that a node can still perform some FRR processing even if the PLR and MP flags are clear (at a detour transit for instance).
Status: current	Access: read-create
OBJECT-TYPE
	BITS	fastReroutePLR(0), fastRerouteMP(1), fastRerouteDetourRestart(2)

prvtRsvpProductFastRroutBkpRtryInt		78.5.7.1.1.1.46
When this node is a PLR, this field specifies the period that the node should wait before retrying the setup of a backup LSP which failed last time because no route was available. In the case that a backup LSP is set up but an error is received from upstream, setup will be attempted again immediately. This field is only valid if this node is defined as PLR capable in the _prvtRsvpProductFastRerouteCapabilities_ field above.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

prvtRsvpProductErrorActionFlags		78.5.7.1.1.1.47
This field is used by PRVT-RSVP to determine whether it should take any special action following certain types of local errors. Each bit of this flags field corresponds to an error and a corresponding action. When one of these errors occurs, the relevant bit flag is checked - if set, the specified action is taken; if not set, the normal action is taken according the RSVP protocol. The possible bit values are the following. - eafTearStateOnLSIErr: When PRVT-RSVP receives a negative response to an ATG_LDB_CONNECT_LSP_XC message on a UNI node, the Path state is torn down.
Status: current	Access: read-create
OBJECT-TYPE
	BITS	eafTearStateOnLSIErr(0)

prvtRsvpProductEnableNni		78.5.7.1.1.1.48
A flag to indicate whether the local node supports NNI signaling messages.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2), disabling(3)

prvtRsvpProductBehaviorFlags		78.5.7.1.1.1.49
Specifies some detailed aspects of the behavior of PRVT-RSVP. This field may be changed while _admin_status_ is up. - enableTTLMatch: Whether to discard received RSVP packets sent with the Router Alert option if the IP and RSVP TTL values do not match. In certain circumstances TTL comparison can identify RSVP service breaks, and allow the discarding of packets that would otherwise disrupt installed LSPs. This option has no effect for Out Of Band operation. This option should be left disabled for LSP hierarchy operation (LSPs set up over existing LSPs) and for Facility Fast Reroute (which sets up backup LSPs over existing bypass LSPs).
Status: current	Access: read-create
OBJECT-TYPE
	BITS	enableTTLMatch(0)

prvtRsvpProductLabelSetStyle		78.5.7.1.1.1.50
Specifies the style of LABEL_SET object that should be used. RFCs 3741 and 3743 are unclear whether the LABEL_SET object should include LABEL headers. The correct interpretation is that the header should not be present, but there are implementations that include the LABEL header, so this option is included for compatibility with these implementations. - excludeLabelHeader: The LABEL_SET object contains concatenated LABEL values without the object headers. - includeLabelHeader: The LABEL_SET object contains concatenated LABEL objects with the object headers.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	excludeLabelHeader(1), includeLabelHeader(2)

prvtRsvpProductLabelSetOperStatus		78.5.7.1.1.1.51
The current operational state of Label Set style. - excludeLabelHeader: The LABEL_SET object contains concatenated LABEL values without the object headers. - includeLabelHeader: The LABEL_SET object contains concatenated LABEL objects with the object headers. - goingToExclude: The Label Set Style is being changed from includeLabelHeader to excludeLabelHeader. - goingToInclude: The Label Set Style is being changed from excludeLabelHeader to includeLabelHeader.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	excludeLabelHeader(1), includeLabelHeader(2), goingToExclude(3), goingToInclude(4)

prvtRsvpProductLabelSetTrapEnable		78.5.7.1.1.1.52
This object is used to enable traps for the Label Set style oper_status object.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

prvtRsvpProductLabelSetChngAct		78.5.7.1.1.1.53
Specifies the action to take when the value of prvtRsvpProductLabelSetStyle is changed. - leaveLSPs: All nodes should suppress refreshes and switch to the new format while refreshes are suppressed. - tearLSPs: Any LSPs using label sets will be deleted before switching all nodes to the new format, and any new LSPs using label sets will be dropped/rejected until the switch is complete.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

prvtRsvpProductExtPrtAdminStatus		78.5.7.1.1.1.54
The desired operational state of support for the extended PROTECTION object defined in draft-lang-ccamp-gmpls-recovery-e2e-signaling.
Status: current	Access: read-create
OBJECT-TYPE
	PrvtRsvpAdminStatus

prvtRsvpProductUniIncSonetProfile		78.5.7.1.1.1.55
Specifies whether Sonet Profile is included on messages to or from a UNI-C node.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..1

prvtRsvpProductFrrFacAdminStatus		78.5.7.1.1.1.56
Specifies whether backup LSPs can be put in place for LSPs requesting FRR using the facility method. Setting this to UP means that LSPs that request FRR using the facility method can have protection at this node. Existing LSPs that request FRR facility protection will have protection put in place when the next Path refresh is received. Setting this to DOWN means that LSPs that request FRR using the facility method will not be protected at this node. Existing LSPs that have FRR facility protection will lose that protection, and if the LSP had been rerouted to use the backup LSP then the protected LSP will be lost. This field replaces the bypassFastReroute flag on the protocol extensions field in this MIB (although the bypassFastReroute flag is still supported for backwards compatibility). It can be modified while RSVP is oper_status UP or DOWN. When this field is changed the bypassFastReroute flag is automatically modified to mirror the change.
Status: current	Access: read-create
OBJECT-TYPE
	PrvtRsvpAdminStatus

prvtRsvpProductFrrFacOperStatus		78.5.7.1.1.1.57
The current operational status for FRR Facility support. When this is UP backup LSPs will be put in place, when this is down backup LSPs will not be put in place and there will be no LSPs that have backup LSPs.
Status: current	Access: read-only
OBJECT-TYPE
	PrvtRsvpOperStatus

prvtRsvpProductIpv6AdminStatus		78.5.7.1.1.1.58
Specifies whether the local node supports IPv6 LSPs. Setting this to UP means that this node supports IPv6 LSPs being set up to, from and through this node. Setting this to DOWN means that IPv6 LSPs are NOT supported by this node. Existing IPv6 LSPs for which this node is the ingress, egress or transit are torn down. This field can be modified while RSVP is oper_status UP or DOWN. The value of this field MUST match the value of the dcMplsTeMibRsvpIpv6AdminStatus field in the prvtMplsTeMibEntityTable.
Status: current	Access: read-write
OBJECT-TYPE
	PrvtRsvpAdminStatus

prvtRsvpProductIpv6OperStatus		78.5.7.1.1.1.59
The current operational status for IPv6 support. When this is UP IPv6 LSPs can be set up to from or through this node. When this is down there will be no active IPv6 LSPs.
Status: current	Access: read-only
OBJECT-TYPE
	PrvtRsvpOperStatus

prvtRsvpProductAPIIpv6Address		78.5.7.1.1.1.60
Management assigned IPv6 address used to identify the (internal) LRAPI interface between RSVP and TE-MIB components. The configured API IPv6 address MUST not be a real address in the network. It is recommended that this is set to a non-zero reserved address value. This MUST be an address with global scope. If multi-stack support is set to PHOP, this address must be unique for each RSVP stack in the node. The same address(es) can be used on all nodes in the network.
Status: current	Access: read-create
OBJECT-TYPE
	InetAddressIPv6

prvtRsvpDiagnosticTable		78.5.7.1.2
The table of sessions that are being diagnosed.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrvtRsvpDiagnosticEntry

prvtRsvpDiagnosticEntry		78.5.7.1.2.1
Each entry represents a session that is being diagnosed.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrvtRsvpDiagnosticEntry

prvtRsvpDiagProductIndex		78.5.7.1.2.1.1
The index of the PRVT-RSVP product that is handling this query.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrvtRsvpIndex

prvtRsvpDiagRequestIndex		78.5.7.1.2.1.2
The index of this prvtRsvpDiagnosticEntry. This corresponds to a particular session being diagnosed and is an arbitrary value, defined on row creation.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrvtRsvpDiagReqIndex

prvtRsvpDiagReqsInProgress		78.5.7.1.2.1.3
The number of outstanding diagnostic requests relating to this session.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

prvtRsvpDiagSessionEndPoint		78.5.7.1.2.1.4
The IP address of the tunnel end point, from the LSP_TUNNEL_IPv4 session object.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

prvtRsvpDiagSessionTunnelId		78.5.7.1.2.1.5
The tunnel ID, from the LSP_TUNNEL_IPv4 session object.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

prvtRsvpDiagSessionExtTunnelId		78.5.7.1.2.1.6
The extended tunnel ID, from the LSP_TUNNEL_IPv4 session object.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

prvtRsvpDiagLastHop		78.5.7.1.2.1.7
The IP address of the last hop to be queried. This is the address to which the DREQ message is first sent.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

prvtRsvpDiagSender		78.5.7.1.2.1.8
The IP address of the sender for the specified session.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

prvtRsvpDiagMaxHops		78.5.7.1.2.1.9
The maximum number of hops to diagnose.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..255

prvtRsvpDiagHopByHopReply		78.5.7.1.2.1.10
A flag to indicate that DREPs should be returned hop-by- hop using the reverse of the path taken by the DREQ.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

prvtRsvpDiagNodeTable		78.5.7.1.3
The table of nodes within a session that is being diagnosed. External management can extract information from this table, but cannot modify information in it.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrvtRsvpDiagNodeEntry

prvtRsvpDiagNodeEntry		78.5.7.1.3.1
Each entry represents a node within a session that is being diagnosed.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrvtRsvpDiagNodeEntry

prvtRsvpDiagNodeProductIndex		78.5.7.1.3.1.1
The index of the PRVT-RSVP product that is handling this query.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrvtRsvpIndex

prvtRsvpDiagNodeRequestIndex		78.5.7.1.3.1.2
The index of the corresponding request in prvtRsvpDiagnosticTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrvtRsvpDiagReqIndex

prvtRsvpDiagNodeIndex		78.5.7.1.3.1.3
The index of this prvtRsvpDiagNodeEntry. This is equivalent to the hop number, with 1 being the ingress.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrvtRsvpDiagNodeIndexType

prvtRsvpDiagNodeType		78.5.7.1.3.1.4
The type of the node: ingress, transit, egress or missing. Missing indicates that no diagnostic response has been received for this node, and this entry may in fact represent more than one node.
Status: current	Access: read-only
OBJECT-TYPE
	PrvtRsvpDiagNodeTypeVal

prvtRsvpDiagNodeDreqArrivalTime		78.5.7.1.3.1.5
The arrival time of the DREQ at the node, specified as a 32-bit NTP timestamp.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

prvtRsvpDiagNodeIncomingIfAddr		78.5.7.1.3.1.6
The IP address of the interface on which message from the sender are expected to arrive at this node, or 0 if unknown.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

prvtRsvpDiagNodeOutgoingIfAddr		78.5.7.1.3.1.7
The IP address of the interface through which the DREQ arrived and to which messages flow from the given sender for the specified session address, or 0 if unknown.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

prvtRsvpDiagNodePrevHopAddr		78.5.7.1.3.1.8
The IP address from which this node receives RSVP PATH messages for this source, or 0 if unknown. This is also the address to which the DREQ was forwarded.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

prvtRsvpDiagNodeDTTL		78.5.7.1.3.1.9
The number of IP hops traversed by the DREQ between the downstream RSVP node and this node.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..255

prvtRsvpDiagNodeMFlag		78.5.7.1.3.1.10
A flag that indicates whether the reservation described by the response objects is merged with reservations from other downstream interfaces before being forwarded upstream.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

prvtRsvpDiagNodeRErr		78.5.7.1.3.1.11
The error conditions at this node. Bit 3 indicates ROUTE object too big; Bit 2 indicates packet too big; Bit 1 indicates no PATH state. Bit 1 is the least significant bit.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..7

prvtRsvpDiagNodeKValue		78.5.7.1.3.1.12
The refresh timer multiple.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..15

prvtRsvpDiagNodeTimerValue		78.5.7.1.3.1.13
The local refresh timer value in seconds.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..65535

prvtRsvpDiagRsvpHopAddr		78.5.7.1.3.1.14
The hop address from the session's RSVP_HOP object.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

prvtRsvpDiagRsvpHopLIH		78.5.7.1.3.1.15
The LIH from the session's RSVP_HOP object.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

prvtRsvpDiagSenderTpltAddress		78.5.7.1.3.1.16
The address from the session's SENDER_TEMPLATE object.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

prvtRsvpDiagSenderTpltLSPId		78.5.7.1.3.1.17
The LSP ID from the session's SENDER_TEMPLATE object.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..65535

prvtRsvpDiagFlowSpecCLBktRate		78.5.7.1.3.1.18
Int-serv controlled load token bucket rate in bytes per second, from the session's FLOWSPEC object. This value is rounded to the nearest integer.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

prvtRsvpDiagFlowSpecCLBktDep		78.5.7.1.3.1.19
Int-serv controlled load token bucket depth in bytes, from the session's FLOWSPEC object. This value is rounded to the nearest integer.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

prvtRsvpDiagFlowSpecCLPkDataRate		78.5.7.1.3.1.20
Int-serv controlled load peak data rate in bytes per second, from the session's FLOWSPEC object. This value is rounded to the nearest integer.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

prvtRsvpDiagFlowSpecCLMinPolUnit		78.5.7.1.3.1.21
Int-serv controlled load minimum policed unit from the session's FLOWSPEC object.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

prvtRsvpDiagFlowSpecCLMaxPktSize		78.5.7.1.3.1.22
Int-serv controlled load maximum packet size from the session's FLOWSPEC object.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

prvtRsvpDiagFlowSpecGQBktRate		78.5.7.1.3.1.23
Int-serv guaranteed QoS token bucket rate in bytes per second, from the session's FLOWSPEC object. This value is rounded to the nearest integer.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

prvtRsvpDiagFlowSpecGQBktDep		78.5.7.1.3.1.24
Int-serv guaranteed QoS token bucket depth in bytes, from the session's FLOWSPEC object. This value is rounded to the nearest integer.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

prvtRsvpDiagFlowSpecGQPkDataRate		78.5.7.1.3.1.25
Int-serv guaranteed QoS peak data rate in bytes per second, from the session's FLOWSPEC object. This value is rounded to the nearest integer.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

prvtRsvpDiagFlowSpecGQMinPolUnit		78.5.7.1.3.1.26
Int-serv guaranteed QoS minimum policed unit from the session's FLOWSPEC object.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

prvtRsvpDiagFlowSpecGQMaxPktSize		78.5.7.1.3.1.27
Int-serv guaranteed QoS maximum packet size from the session's FLOWSPEC object.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

prvtRsvpDiagFlowSpecGQRate		78.5.7.1.3.1.28
Int-serv guaranteed QoS rate in bytes per second, from the session's FLOWSPEC object. This value is rounded to the nearest integer.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

prvtRsvpDiagFlowSpecGQSlack		78.5.7.1.3.1.29
Int-serv guaranteed QoS slack in microseconds, from the session's FLOWSPEC object.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

prvtRsvpDiagFlowSpecCoSCoS		78.5.7.1.3.1.30
CoS class of service from the session's FLOWSPEC object.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..255

prvtRsvpDiagFlowSpecCoSMTU		78.5.7.1.3.1.31
CoS maximum packet size from the session's FLOWSPEC object.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..65535

prvtRsvpDiagFilterSpecAddress		78.5.7.1.3.1.32
The address from the session's FILTER_SPEC object.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

prvtRsvpDiagFilterSpecLSPId		78.5.7.1.3.1.33
The LSP ID from the session's FILTER_SPEC object.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..65535

prvtRsvpDiagConfirmRcvAddr		78.5.7.1.3.1.34
The address from the session's CONFIRM object.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

prvtRsvpDiagStyle		78.5.7.1.3.1.35
The style word from the session's STYLE object.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

prvtRsvpConformance		78.5.7.2
OBJECT IDENTIFIER

prvtRsvpCompliances		78.5.7.2.1
OBJECT IDENTIFIER

prvtRsvpGroups		78.5.7.2.2
OBJECT IDENTIFIER

prvtRsvpCompliance		78.5.7.2.1.1
The compliance statement for the PRVT-RSVP product MIB.
Status: current	Access: read-only
MODULE-COMPLIANCE

prvtRsvpProductGroup		78.5.7.2.2.2
Product Table Objects.
Status: current	Access: read-only
OBJECT-GROUP

prvtRsvpDiagGroup		78.5.7.2.2.3
Diagnostic Table Objects.
Status: current	Access: read-only
OBJECT-GROUP

prvtRsvpDiagNodeGroup		78.5.7.2.2.4
Diag Node Table Objects.
Status: current	Access: read-only
OBJECT-GROUP