PDN-XDSL-INTERFACE-MIB

File: PDN-XDSL-INTERFACE-MIB.mib (31518 bytes)

Imported modules

SNMPv2-TC RFC-1212 RFC-1215
RFC1213-MIB PDN-HEADER-MIB

Imported symbols

DisplayString OBJECT-TYPE TRAP-TYPE
ifIndex pdn-xdsl

Defined Types

XdslDevGenericIfConfigEntry  
SEQUENCE    
  xdslDevGenericIfConfigPortSpeedBehaviour INTEGER
  xdslDevGenericIfConfigMarginThreshold INTEGER
  xdslDevGenericIfConfigPortID DisplayString Size(1..40)
  xdslDevGenericIfConfigLinkUpDownTransitionThreshold INTEGER
  xdslDevGenericIfConfigLineEncodeType INTEGER
  xdslDevGenericIfConfigLineRateMode INTEGER
  xdslDevGenericIfConfigLinkEncapType INTEGER
  xdslDevGenericIfConfigSnType OBJECT IDENTIFIER

XdslDevRADSLSpecificIfConfigEntry  
SEQUENCE    
  xdslDevRADSLSpecificIfConfigUpFixedPortSpeed INTEGER
  xdslDevRADSLSpecificIfConfigDownFixedPortSpeed INTEGER
  xdslDevRADSLSpecificIfConfigUpAdaptiveUpperBoundPortSpeed INTEGER
  xdslDevRADSLSpecificIfConfigUpAdaptiveLowerBoundPortSpeed INTEGER
  xdslDevRADSLSpecificIfConfigDownAdaptiveUpperBoundPortSpeed INTEGER
  xdslDevRADSLSpecificIfConfigDownAdaptiveLowerBoundPortSpeed INTEGER
  xdslDevRADSLSpecificIfConfigReedSolomonDownFwdErrCorrection INTEGER
  xdslDevRADSLSpecificIfConfigStartUpMargin INTEGER -3..9
  xdslDevRADSLSpecificIfConfigTxPowerAttenuation INTEGER
  xdslDevRADSLSpecificIfConfigSnTxPowerAttenuation INTEGER

XdslDevMVLSpecificIfConfigEntry  
SEQUENCE    
  xdslDevMVLSpecificIfConfigMaxPortSpeed INTEGER
  xdslDevMVLSpecificIfConfigOnHookTxPowerAttenuation INTEGER
  xdslDevMVLSpecificIfConfigOffHookTxPowerAttenuation INTEGER
  xdslDevMVLSpecificIfConfigOnHookPCVoltageDropThresholdValue INTEGER
  xdslDevMVLSpecificIfConfigOnHookSNVoltageDropThresholdValue INTEGER
  xdslDevMVLSpecificIfConfigMaxDownStreamPortSpeed INTEGER
  xdslDevMVLSpecificIfConfigMaxUpStreamPortSpeed INTEGER

XdslDevSDSLSpecificIfConfigEntry  
SEQUENCE    
  xdslDevSDSLSpecificIfConfigFixedPortSpeed INTEGER
  xdslDevSDSLSpecificIfConfigMaxPortSpeed INTEGER
  xdslDevSDSLSpecificIfConfigFixedPortSpeedNx128Mode INTEGER
  xdslDevSDSLSpecificIfConfigMaxPortSpeedNx128Mode INTEGER
  xdslDevSDSLSpecificIfConfigMinSnrMargin INTEGER
  xdslDevSDSLSpecificIfConfigTargetSnrMargin INTEGER

XdslDevIDSLSpecificIfConfigEntry  
SEQUENCE    
  xdslDevIDSLSpecificIfConfigPortSpeed INTEGER
  xdslDevIDSLSpecificIfConfigTimingPortTransceiverMode INTEGER
  xdslDevIDSLSpecificChannel INTEGER

Defined Values

xdslIfConfigMIBObjects 1.3.6.1.4.1.1795.2.24.9.2
OBJECT IDENTIFIER    

xdslIfConfigMIBTraps 1.3.6.1.4.1.1795.2.24.9.4
OBJECT IDENTIFIER    

xdslDevGenericIfConfig 1.3.6.1.4.1.1795.2.24.9.2.1
OBJECT IDENTIFIER    

xdslDevRADSLSpecificIfConfig 1.3.6.1.4.1.1795.2.24.9.2.2
OBJECT IDENTIFIER    

xdslDevMVLSpecificIfConfig 1.3.6.1.4.1.1795.2.24.9.2.3
OBJECT IDENTIFIER    

xdslDevSDSLSpecificIfConfig 1.3.6.1.4.1.1795.2.24.9.2.4
OBJECT IDENTIFIER    

xdslDevIDSLSpecificIfConfig 1.3.6.1.4.1.1795.2.24.9.2.5
OBJECT IDENTIFIER    

xdslDevGenericIfConfigTable 1.3.6.1.4.1.1795.2.24.9.2.1.1
The xdslDevGenericIfConfigTable provides config information generic to a xDSL device, or system. The table is indexed by an object which corresponds to ifIndex. These ifIndex entries, themselves, denote and identify specific xdsl interfaces on the board or module. Also the configuration parameters are grouped into two broad categories, 'up' and 'down'. 'up' reflects the upstream direction (from the customer premises to the central office). 'Down' reflects the downstream direction (from the central office to the customer premises)
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    XdslDevGenericIfConfigEntry

xdslDevGenericIfConfigEntry 1.3.6.1.4.1.1795.2.24.9.2.1.1.1
Describes a specific xDSL interface entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  XdslDevGenericIfConfigEntry  

xdslDevGenericIfConfigPortSpeedBehaviour 1.3.6.1.4.1.1795.2.24.9.2.1.1.1.1
The value of this object corresponds to the behaviour of the specified port. The default value for this object is fixed (1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER fixed(1), adaptive(2)  

xdslDevGenericIfConfigMarginThreshold 1.3.6.1.4.1.1795.2.24.9.2.1.1.1.2
The value of this object corresponds to the offset from the startup margin. The threshold margin is calculated by subtracting the offset from the startup margin. Permissible range of values are between -7 and 14. A value of -9999 disables the threshold check. The default value of this object is 3
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

xdslDevGenericIfConfigPortID 1.3.6.1.4.1.1795.2.24.9.2.1.1.1.3
The value of this object corresponds to 40 character information only field that identifies what the DSL port is connected to (Circuit ID, MDF location, Customer name, etc.)
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..40)  

xdslDevGenericIfConfigLinkUpDownTransitionThreshold 1.3.6.1.4.1.1795.2.24.9.2.1.1.1.4
The value of this object corresponds to the threshold value for link up-down transitions. If link up-down's exceed this threshold value a xdslLinkupDownTransitions trap is generated. This value would represent the number of link up-down transitions in a 15 minute interval. A value of -9999 disables the threshold check. The default value for this object is 0
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

xdslDevGenericIfConfigLineEncodeType 1.3.6.1.4.1.1795.2.24.9.2.1.1.1.5
The value of this object corresponds to the line encoding technology used for data transmission over the the dsl link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), cap(2), twoB1q(3), mvl(4), g-lite(5), dmt(6)  

xdslDevGenericIfConfigLineRateMode 1.3.6.1.4.1.1795.2.24.9.2.1.1.1.6
The value of this object is used to choose the line rate list for data transmission over the dsl link. The default value is standard(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER standard(1), nx128(2)  

xdslDevGenericIfConfigLinkEncapType 1.3.6.1.4.1.1795.2.24.9.2.1.1.1.7
The value of this object corresponds to the link encapsulation type. Following are valid settings: linkNone (1) ethernet (2) ppp (3) slip (4) frameRelay-PLL (5) x23PVC (6) x25SVC (7) hdlc (8) etherHDLC (9) rfc1483-MPOA (10) funi-MPOA (11) frf5 (12) frf8 (13) pppoAVC-Mux (14) pppoALLC (15)
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER linkNone(1), ethernet(2), ppp(3), slip(4), frameRelay-PLL(5), x23PVC(6), x25SVC(7), hdlc(8), etherHDLC(9), rfc1483-MPOA(10), funi-MPOA(11), frf5(12), frf8(13), pppoAVC-Mux(14), pppoALLC(15)  

xdslDevGenericIfConfigSnType 1.3.6.1.4.1.1795.2.24.9.2.1.1.1.8
The value of this object is used to choose a valid Service Node Type to be configured in the port. The configurable values are the object identifiers of the remote endpoints as defined in the xdsl-remote group of the pdn-xdsl-products. The following are examples of valid endpoints for the 8312 Reach port card: xdsl_6350, xdsl_6351, xdsl_6310 By default, this object will be set to the default service node associated with the portcard.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OBJECT IDENTIFIER  

xdslDevRADSLSpecificIfConfigTable 1.3.6.1.4.1.1795.2.24.9.2.2.1
The xdslDevRADSLSpecificIfConfigTable provides config information specific to a xDSL device, or system. The table is indexed by an object which corresponds to ifIndex. These ifIndex entries, themselves, denote and identify specific xdsl interfaces on the board or module. Also the configuration parameters are grouped into two broad categories, 'up' and 'down'. 'up' reflects the upstream direction (from the customer premises to the central office). 'Down' reflects the downstream direction (from the central office to the customer premises)
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    XdslDevRADSLSpecificIfConfigEntry

xdslDevRADSLSpecificIfConfigEntry 1.3.6.1.4.1.1795.2.24.9.2.2.1.1
Describes a specific xDSL interface entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  XdslDevRADSLSpecificIfConfigEntry  

xdslDevRADSLSpecificIfConfigUpFixedPortSpeed 1.3.6.1.4.1.1795.2.24.9.2.2.1.1.1
The value of this object corresponds to the upstream speed of the specified port for fixed port speed behaviour. All the speeds are in kbps. If the port speed behaviour is adaptive an error of noSuchName will be returned by the agent.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

xdslDevRADSLSpecificIfConfigDownFixedPortSpeed 1.3.6.1.4.1.1795.2.24.9.2.2.1.1.2
The value of this object corresponds to the downstream speed of the specified port for fixed port speed behaviour. All the speeds are in kbps. If the port speed behaviour is adaptive an error of noSuchName will be returned by the agent.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

xdslDevRADSLSpecificIfConfigUpAdaptiveUpperBoundPortSpeed 1.3.6.1.4.1.1795.2.24.9.2.2.1.1.3
The value of this object corresponds to the upper bound for the upstream port speed of the specified port for adaptive port speed behaviour. The speeds are measured in kbps. If the port speed behaviour is fixed an error of noSuchName will be returned by the agent.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

xdslDevRADSLSpecificIfConfigUpAdaptiveLowerBoundPortSpeed 1.3.6.1.4.1.1795.2.24.9.2.2.1.1.4
The value of this object corresponds to the lower bound for the upstream port speed of the specified port for adaptive port speed behaviour in kbps. If the port speed behaviour is fixed an error of noSuchName will be returned by the agent. The value -9999 should be used to disable the lower bound threshold check. The default value for this object is -9999
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

xdslDevRADSLSpecificIfConfigDownAdaptiveUpperBoundPortSpeed 1.3.6.1.4.1.1795.2.24.9.2.2.1.1.5
The value of this object corresponds to the upper bound allowed for the downstream port speed of the specified port for adaptive port speed behaviour. The speeds are measured in kbps. If the port speed behaviour is fixed an error of noSuchName will be returned by the agent.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

xdslDevRADSLSpecificIfConfigDownAdaptiveLowerBoundPortSpeed 1.3.6.1.4.1.1795.2.24.9.2.2.1.1.6
The value of this object corresponds to the Minimum lower bound allowed for the downstream port speed of the specified port for adaptive port speed behaviour. If the port speed behaviour is fixed an error of noSuchName will be returned by the agent. The speeds are measured in kbps. The value -9999 is used to disable the lower bound threshold check.The default value for this object is -9999
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

xdslDevRADSLSpecificIfConfigReedSolomonDownFwdErrCorrection 1.3.6.1.4.1.1795.2.24.9.2.2.1.1.7
The value of this object corresponds to the Reed-Solomon forward error correction in the downstream direction. The default value of this object should be minimizeError (1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimizeError(1), minimizeDelay(2), reedSolomonNotSupported(3)  

xdslDevRADSLSpecificIfConfigStartUpMargin 1.3.6.1.4.1.1795.2.24.9.2.2.1.1.8
The value of this object corresponds to the startup value of the margin for a DSL interface (specified by ifIndex). The unit is db (decibels. The higher the margin the better the quality of the line. The default value of this object is 3.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER -3..9  

xdslDevRADSLSpecificIfConfigTxPowerAttenuation 1.3.6.1.4.1.1795.2.24.9.2.2.1.1.9
This value corresponds to the Transmitt Power Attenuation in dB for the access node. This value represents the downstream power level in dB. Permissible values are -6, -3 and 0. The default value of this object is 0 dB. The power levels +3 and +6 may be used in future.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

xdslDevRADSLSpecificIfConfigSnTxPowerAttenuation 1.3.6.1.4.1.1795.2.24.9.2.2.1.1.10
This value corresponds to the Transmitt Power Attenuation in dB for the service node. This value represents the upstream power level in dB. Permissible values are -9, -6, -3 and 0. The default value of this object is -6 dB.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

xdslDevMVLSpecificIfConfigTable 1.3.6.1.4.1.1795.2.24.9.2.3.1
The xdslDevMVLSpecificIfConfigTable provides config information specific to a xDSL(MVL) device, or system. The table is indexed by an object which corresponds to ifIndex. These ifIndex entries, themselves, denote and identify specific xdsl(Mvl) interfaces on the board or module.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    XdslDevMVLSpecificIfConfigEntry

xdslDevMVLSpecificIfConfigEntry 1.3.6.1.4.1.1795.2.24.9.2.3.1.1
Describes a specific xDSL(MVL) interface entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  XdslDevMVLSpecificIfConfigEntry  

xdslDevMVLSpecificIfConfigMaxPortSpeed 1.3.6.1.4.1.1795.2.24.9.2.3.1.1.1
The value of this object corresponds to the upper bound port speed of the specified port. The speeds are measured in kbps. Prior to GrandSlam 2.3, this object was used for both upstream and downstream port speeds. Now there are 2 new objects created for downstream and upstream port speeds. Setting this value will also set the same value for the objects xdslDevMVLSpecificIfConfigMaxDownStreamPortSpeed and xdslDevMVLSpecificIfConfigMaxUpStreamPortSpeed.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER  

xdslDevMVLSpecificIfConfigOnHookTxPowerAttenuation 1.3.6.1.4.1.1795.2.24.9.2.3.1.1.2
This value corresponds to the On-hook Transmitt Power Attenuation in dB for the access node and the service node. This value represents both downstream and upstream power level in dB while the phone is On-hook. Permissible values are -2, 1, 4, 7, 10, and +12. The default value of this object is 12 dB.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

xdslDevMVLSpecificIfConfigOffHookTxPowerAttenuation 1.3.6.1.4.1.1795.2.24.9.2.3.1.1.3
This value corresponds to the Off-hook Transmitt Power Attenuation in dB for the access node and the service node. This value represents both downstream and upstream power level in dB while the phone is Off-hook. Permissible values are -11, -8, -5, -2, 1, 4, 7, 10 and +12. The default value of this object is 12 dB.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

xdslDevMVLSpecificIfConfigOnHookPCVoltageDropThresholdValue 1.3.6.1.4.1.1795.2.24.9.2.3.1.1.4
This value correspond to the portcard Voltage Drop Threshold Value and valid settings are 0 and 6. If the corresponding value at the endpoint is set for Max (255) than only valid value for this object is 0. This only applies for MVL configuration If Reach configuration is used only valid value is 6 which is a default value.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

xdslDevMVLSpecificIfConfigOnHookSNVoltageDropThresholdValue 1.3.6.1.4.1.1795.2.24.9.2.3.1.1.5
This corresponds to the endpoint Voltage Drop Threshold Value and valid settings are 17, 34 and 255(Max). If Reach is used than only valid value is 34 - default.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

xdslDevMVLSpecificIfConfigMaxDownStreamPortSpeed 1.3.6.1.4.1.1795.2.24.9.2.3.1.1.6
The value of this object corresponds to the upper bound downstream port speed of the specified port. The speeds are measured in kbps. Setting the value of this object will also set the same value to the object xdslDevMVLSpecificIfConfigMaxPortSpeed. Prior to GrandSlam 2.3, the object xdslDevMVLSpecificIfConfigMaxPortSpeed was used for both upstream and downstream port speeds. Now there are two different objects for upstream and downstream port speeds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

xdslDevMVLSpecificIfConfigMaxUpStreamPortSpeed 1.3.6.1.4.1.1795.2.24.9.2.3.1.1.7
The value of this object corresponds to the upper bound upstream port speed of the specified port. The speeds are measured in kbps. Prior to GrandSlam 2.3, the object MaxPortSpeed was used for both upstream and downstream port speeds. Now there are two different objects for upstream and downstream port speeds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

xdslDevSDSLSpecificIfConfigTable 1.3.6.1.4.1.1795.2.24.9.2.4.1
The xdslDevSDSLSpecificIfConfigTable provides configuration specific to the SDSL link.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    XdslDevSDSLSpecificIfConfigEntry

xdslDevSDSLSpecificIfConfigEntry 1.3.6.1.4.1.1795.2.24.9.2.4.1.1
Describes a specific SDSL configuration entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  XdslDevSDSLSpecificIfConfigEntry  

xdslDevSDSLSpecificIfConfigFixedPortSpeed 1.3.6.1.4.1.1795.2.24.9.2.4.1.1.1
The value of this object corresponds to both upstream and downstream speed of the specified port. All the speeds are in kbps. The value of this object is used only when the port behaviour is fixed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

xdslDevSDSLSpecificIfConfigMaxPortSpeed 1.3.6.1.4.1.1795.2.24.9.2.4.1.1.2
The value of this object corresponds to the upper bound port speed of the specified port when the port behaviour is adaptive. The speeds are measured in kbps.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

xdslDevSDSLSpecificIfConfigFixedPortSpeedNx128Mode 1.3.6.1.4.1.1795.2.24.9.2.4.1.1.3
The value of this object applies to both upstream and downstream speed of the specified port when the line rate mode is configured as Nx128 mode. All the speeds are in kbps. The value of this object is used only when the port behaviour is fixed and the line rate is Nx128 mode, and doesn't take effect in the standard mode.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

xdslDevSDSLSpecificIfConfigMaxPortSpeedNx128Mode 1.3.6.1.4.1.1795.2.24.9.2.4.1.1.4
The value of this object corresponds to the upper bound port speed of the specified port when the port behaviour is adaptive and the line rate is Nx128 mode, and doesn't take effect in the standard mode. The speeds are measured in kbps.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

xdslDevSDSLSpecificIfConfigMinSnrMargin 1.3.6.1.4.1.1795.2.24.9.2.4.1.1.5
Configured Minimum acceptable Signal/Noise Margin.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..15  

xdslDevSDSLSpecificIfConfigTargetSnrMargin 1.3.6.1.4.1.1795.2.24.9.2.4.1.1.6
Configured Target Signal/Noise Margin.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..15  

xdslDevIDSLSpecificIfConfigTable 1.3.6.1.4.1.1795.2.24.9.2.5.1
The xdslDevIDSLSpecificIfConfigTable provides configuration specific to the IDSL link.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    XdslDevIDSLSpecificIfConfigEntry

xdslDevIDSLSpecificIfConfigEntry 1.3.6.1.4.1.1795.2.24.9.2.5.1.1
Describes a specific IDSL configuration entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  XdslDevIDSLSpecificIfConfigEntry  

xdslDevIDSLSpecificIfConfigPortSpeed 1.3.6.1.4.1.1795.2.24.9.2.5.1.1.1
The value of this object corresponds to both upstream and downstream speed of the specified port. All the speeds are in kbps. Allowed speeds are 64, 128 and 144 kbps. The default value for this object is 128 kbps.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

xdslDevIDSLSpecificIfConfigTimingPortTransceiverMode 1.3.6.1.4.1.1795.2.24.9.2.5.1.1.2
The transceiver mode selected on the timing source port. Only one IDSL port can be set to NT mode. This timing will then be distributed to all other IDSL ports in the chassis that are set to LT. The selected xdslDevIDSLPrimaryTimingSourcePort provides clocking signals to the DSLAM when the transceiver mode is set to Network timing. The port selected for Network Timing mode will probably not used for customer data, but will receive a 2.048 Mhz Network clocking signal from a central office timing source and distribute this timing to other IDSL port cards.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER networkTiming(1), localTiming(2)  

xdslDevIDSLSpecificChannel 1.3.6.1.4.1.1795.2.24.9.2.5.1.1.3
The channel type for 64 Kbps. Default value is B1.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER b1(1), b2(2), noOp(3)  

xdslLinkUpDownTransitions 1
This trap signifies that the sending protocol entity recognizes that one of the xDSL communication links is in a fluctuating state.
TRAP-TYPE    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor