PDN-LINK-FAULT-MGMT-MIB

File: PDN-LINK-FAULT-MGMT-MIB.mib (10542 bytes)

Imported modules

SNMPv2-SMI RFC1213-MIB PDN-HEADER-MIB
SNMPv2-CONF

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Integer32
ifIndex pdnLinkFaultMgmt MODULE-COMPLIANCE
OBJECT-GROUP

Defined Types

PdnLinkFailureConfigEntry  
SEQUENCE    
  pdnLinkFailureLOSPeriodBeforeSwitching Integer32
  pdnLinkFailureLOFPeriodBeforeSwitching Integer32
  pdnLinkFailureAISLPeriodBeforeSwitching Integer32
  pdnLinkFailureSdPeriodBeforeSwitching Integer32
  pdnLinkFailureSfPeriodBeforeSwitching Integer32
  pdnLinkFailureSdBerThreshold Integer32
  pdnLinkFailureSfBerThreshold Integer32

Defined Values

pdnLinkFaultMgmtMIB 1.3.6.1.4.1.1795.2.24.2.40.1
This management information module supports the objects to be used for fault management configuration on primary and secondary links.
MODULE-IDENTITY    

pdnLinkFaultMgmtMIBObjects 1.3.6.1.4.1.1795.2.24.2.40.1.1
OBJECT IDENTIFIER    

pdnLinkFaultMgmtMIBConformance 1.3.6.1.4.1.1795.2.24.2.40.1.2
OBJECT IDENTIFIER    

pdnLinkFaultMgmtApsSelection 1.3.6.1.4.1.1795.2.24.2.40.1.1.1
This object is used to enable or disable the Automatic Protection Switching (Aps) feature on this device. This object can not be enabled if the -Switchover due to link failures- is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

pdnLinkFaultMgmtSwitchoverSelection 1.3.6.1.4.1.1795.2.24.2.40.1.1.2
This object is used to enable or disable the Switchover Due to link failures feature on on this device. This object can not be enabled if the APS feature is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

pdnDualLinkSelection 1.3.6.1.4.1.1795.2.24.2.40.1.1.4
This object is used to enable or disable the ability to split traffic among dual links.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

pdnLinkFailureConfigTable 1.3.6.1.4.1.1795.2.24.2.40.1.1.3
This table contains one row per link being monitored for link failures.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PdnLinkFailureConfigEntry

pdnLinkFailureConfigEntry 1.3.6.1.4.1.1795.2.24.2.40.1.1.3.1
Configuration information about a particular interface being monitored for link failured.
Status: current Access: not-accessible
OBJECT-TYPE    
  PdnLinkFailureConfigEntry  

pdnLinkFailureLOSPeriodBeforeSwitching 1.3.6.1.4.1.1795.2.24.2.40.1.1.3.1.1
This object allows users to configure the amount of time a LOS condition shall exist on this uplink before initiating a switchover. Switchover due to LOS condition on this uplink will not be valid if any of the APS (Automatic Protection Switching) is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..300  

pdnLinkFailureLOFPeriodBeforeSwitching 1.3.6.1.4.1.1795.2.24.2.40.1.1.3.1.2
This object allows users to configure the amount of time a LOF condition shall exist on this uplink before initiating a switchover. Switchover due to LOF condition on this uplink will not be valid if any of the APS (Automatic Protection Switching) is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..300  

pdnLinkFailureAISLPeriodBeforeSwitching 1.3.6.1.4.1.1795.2.24.2.40.1.1.3.1.3
This object allows users to configure the amount of time a AIS-L condition shall exist on this uplink before initiating a switchover. Switchover due to AIS-L condition on this uplink will not be valid if any of the APS (Automatic Protection Switching) is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..300  

pdnLinkFailureSdPeriodBeforeSwitching 1.3.6.1.4.1.1795.2.24.2.40.1.1.3.1.4
This object allows users to configure the amount of time a Signal Degraded (Sd) condition shall exist on this uplink before initiating a switchover. Switchover due to Sd condition on this uplink will not be valid if any of the APS (Automatic Protection Switching) is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..300  

pdnLinkFailureSfPeriodBeforeSwitching 1.3.6.1.4.1.1795.2.24.2.40.1.1.3.1.5
This object allows users to configure the amount of time a Signal Failure Bit (Sf) condition shall exist on this uplink before initiating a switchover. Switchover due to Sf condition on this uplink will not be valid if any of the APS (Automatic Protection Switching) is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..300  

pdnLinkFailureSdBerThreshold 1.3.6.1.4.1.1795.2.24.2.40.1.1.3.1.6
This object allows users to configure the threshold for the Signal Degrade Bit Error Rate (Sd). The negated value of this number is used as the exponent of 10 for computing the threshold value for the Bit Error Rate (BER). For example, a value of 5 indicates a BER threshold of 10^-5.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 5..9  

pdnLinkFailureSfBerThreshold 1.3.6.1.4.1.1795.2.24.2.40.1.1.3.1.7
This object allows users to configure the threshold for the Signal Failure Bit Error Rate (Sf). The negated value of this number is used as the exponent of 10 for computing the threshold value for the Bit Error Rate (BER). For example, a value of 5 indicates a BER threshold of 10^-5.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 3..5  

pdnLinkFaultMgmtCompliances 1.3.6.1.4.1.1795.2.24.2.40.1.2.1
OBJECT IDENTIFIER    

pdnLinkFaultMgmtGroups 1.3.6.1.4.1.1795.2.24.2.40.1.2.2
OBJECT IDENTIFIER    

pdnLinkFaultMgmtCompliance 1.3.6.1.4.1.1795.2.24.2.40.1.2.1.1
The compliance statement for SNMP entities capable of configuring link fault conditions.
Status: current Access: read-only
MODULE-COMPLIANCE    

pdnLinkFaultMgmtGeneralGroup 1.3.6.1.4.1.1795.2.24.2.40.1.2.2.1
A collection of configuration objects applicable to link fault mgmt implementation.
Status: current Access: read-only
OBJECT-GROUP    

pdnLinkSwitchoverGroup 1.3.6.1.4.1.1795.2.24.2.40.1.2.2.2
A collection of configuration objects applicable to all redundancy implementations.
Status: current Access: read-only
OBJECT-GROUP