Nortel-Magellan-Passport-Frf5EpMIB

File: Nortel-Magellan-Passport-Frf5EpMIB.mib (85822 bytes)

Imported modules

RFC-1212 Nortel-Magellan-Passport-UsefulDefinitionsMIB Nortel-Magellan-Passport-StandardTextualConventionsMIB
Nortel-Magellan-Passport-TextualConventionsMIB Nortel-Magellan-Passport-McsMgrMIB

Imported symbols

OBJECT-TYPE passportMIBs Counter32
RowPointer DisplayString StorageType
RowStatus Integer32 Unsigned32
AsciiString NonReplicated HexString
IntegerSequence mcsMgrIndex mcsMgr

Defined Types

McsMgrFrf5EpGRowStatusEntry  
SEQUENCE    
  mcsMgrFrf5EpGRowStatus RowStatus
  mcsMgrFrf5EpGComponentName DisplayString
  mcsMgrFrf5EpGStorageType StorageType
  mcsMgrFrf5EpGIndex Integer32

McsMgrFrf5EpGAddrRowStatusEntry  
SEQUENCE    
  mcsMgrFrf5EpGAddrRowStatus RowStatus
  mcsMgrFrf5EpGAddrComponentName DisplayString
  mcsMgrFrf5EpGAddrStorageType StorageType
  mcsMgrFrf5EpGAddrIndex NonReplicated

McsMgrFrf5EpGAddrProvEntry  
SEQUENCE    
  mcsMgrFrf5EpGAddrRemoteAddress AsciiString
  mcsMgrFrf5EpGAddrCommentText AsciiString

McsMgrFrf5EpGAddrAddrPreEntry  
SEQUENCE    
  mcsMgrFrf5EpGAddrAddrPreValue AsciiString
  mcsMgrFrf5EpGAddrAddrPreRowStatus RowStatus

McsMgrFrf5EpGEpRowStatusEntry  
SEQUENCE    
  mcsMgrFrf5EpGEpRowStatus RowStatus
  mcsMgrFrf5EpGEpComponentName DisplayString
  mcsMgrFrf5EpGEpStorageType StorageType
  mcsMgrFrf5EpGEpIndex Integer32

McsMgrFrf5EpGEpStateEntry  
SEQUENCE    
  mcsMgrFrf5EpGEpAdminState INTEGER
  mcsMgrFrf5EpGEpOperationalState INTEGER
  mcsMgrFrf5EpGEpUsageState INTEGER
  mcsMgrFrf5EpGEpAvailabilityStatus OCTET STRING
  mcsMgrFrf5EpGEpProceduralStatus OCTET STRING
  mcsMgrFrf5EpGEpControlStatus OCTET STRING
  mcsMgrFrf5EpGEpAlarmStatus OCTET STRING
  mcsMgrFrf5EpGEpStandbyStatus INTEGER
  mcsMgrFrf5EpGEpUnknownStatus INTEGER

McsMgrFrf5EpGEpOperEntry  
SEQUENCE    
  mcsMgrFrf5EpGEpLastVccClearCause Unsigned32
  mcsMgrFrf5EpGEpConnectionTransferPriority Unsigned32
  mcsMgrFrf5EpGEpServiceCategory INTEGER
  mcsMgrFrf5EpGEpPeakCellRate01 Unsigned32
  mcsMgrFrf5EpGEpSustainedCellRate0 Unsigned32
  mcsMgrFrf5EpGEpSustainedCellRate01 Unsigned32
  mcsMgrFrf5EpGEpMaximumBurstSize0 Unsigned32
  mcsMgrFrf5EpGEpMaximumBurstSize01 Unsigned32
  mcsMgrFrf5EpGEpAvgFrameSize Unsigned32
  mcsMgrFrf5EpGEpTrafficParmConversionPolicy INTEGER
  mcsMgrFrf5EpGEpType INTEGER
  mcsMgrFrf5EpGEpLastVccCauseDiag HexString

McsMgrFrf5EpGEpLmiRowStatusEntry  
SEQUENCE    
  mcsMgrFrf5EpGEpLmiRowStatus RowStatus
  mcsMgrFrf5EpGEpLmiComponentName DisplayString
  mcsMgrFrf5EpGEpLmiStorageType StorageType
  mcsMgrFrf5EpGEpLmiIndex NonReplicated

McsMgrFrf5EpGEpLmiParmsEntry  
SEQUENCE    
  mcsMgrFrf5EpGEpLmiProcedures INTEGER
  mcsMgrFrf5EpGEpLmiAsyncStatusReport INTEGER
  mcsMgrFrf5EpGEpLmiErrorEventThreshold Unsigned32
  mcsMgrFrf5EpGEpLmiEventCount Unsigned32
  mcsMgrFrf5EpGEpLmiCheckPointTimer Unsigned32
  mcsMgrFrf5EpGEpLmiSide INTEGER

McsMgrFrf5EpGEpLmiNniParmsEntry  
SEQUENCE    
  mcsMgrFrf5EpGEpLmiFullStatusPollingCycles Unsigned32
  mcsMgrFrf5EpGEpLmiLinkVerificationTimer Unsigned32

McsMgrFrf5EpGEpLmiStateEntry  
SEQUENCE    
  mcsMgrFrf5EpGEpLmiAdminState INTEGER
  mcsMgrFrf5EpGEpLmiOperationalState INTEGER
  mcsMgrFrf5EpGEpLmiUsageState INTEGER

McsMgrFrf5EpGEpLmiPsiEntry  
SEQUENCE    
  mcsMgrFrf5EpGEpLmiProtocolStatus INTEGER

McsMgrFrf5EpGEpLmiStatsEntry  
SEQUENCE    
  mcsMgrFrf5EpGEpLmiKeepAliveStatusToInterface Counter32
  mcsMgrFrf5EpGEpLmiFullStatusToInterface Counter32
  mcsMgrFrf5EpGEpLmiKeepAliveStatusEnqFromInterface Counter32
  mcsMgrFrf5EpGEpLmiFullStatusEnqFromInterface Counter32
  mcsMgrFrf5EpGEpLmiNetworkSideEventHistory AsciiString
  mcsMgrFrf5EpGEpLmiUserSideEventHistory AsciiString
  mcsMgrFrf5EpGEpLmiProtocolErrors Counter32
  mcsMgrFrf5EpGEpLmiUnexpectedIes Counter32
  mcsMgrFrf5EpGEpLmiSequenceErrors Counter32
  mcsMgrFrf5EpGEpLmiStatusSequenceErrors Counter32
  mcsMgrFrf5EpGEpLmiUnexpectedReports Counter32
  mcsMgrFrf5EpGEpLmiPollingVerifTimeouts Counter32
  mcsMgrFrf5EpGEpLmiNoStatusReportCount Counter32
  mcsMgrFrf5EpGEpLmiKeepAliveEnqToIf Counter32
  mcsMgrFrf5EpGEpLmiFullStatusEnqToIf Counter32

McsMgrFrf5EpGEpEpdRowStatusEntry  
SEQUENCE    
  mcsMgrFrf5EpGEpEpdRowStatus RowStatus
  mcsMgrFrf5EpGEpEpdComponentName DisplayString
  mcsMgrFrf5EpGEpEpdStorageType StorageType
  mcsMgrFrf5EpGEpEpdIndex NonReplicated

McsMgrFrf5EpGEpEpdProvEntry  
SEQUENCE    
  mcsMgrFrf5EpGEpEpdRemoteConnectionIdentifier IntegerSequence
  mcsMgrFrf5EpGEpEpdConnectionTransferPriority Unsigned32
  mcsMgrFrf5EpGEpEpdCommittedInformationRate Unsigned32
  mcsMgrFrf5EpGEpEpdExcessInformationRate Unsigned32
  mcsMgrFrf5EpGEpEpdCommittedBurstSize Unsigned32
  mcsMgrFrf5EpGEpEpdType INTEGER
  mcsMgrFrf5EpGEpEpdAccessRate Unsigned32
  mcsMgrFrf5EpGEpEpdExcessBurstSize Unsigned32

McsMgrFrf5EpGEpEpdCidDataEntry  
SEQUENCE    
  mcsMgrFrf5EpGEpEpdCustomerIdentifier Unsigned32

McsMgrFrf5EpGEpDlciRowStatusEntry  
SEQUENCE    
  mcsMgrFrf5EpGEpDlciRowStatus RowStatus
  mcsMgrFrf5EpGEpDlciComponentName DisplayString
  mcsMgrFrf5EpGEpDlciStorageType StorageType
  mcsMgrFrf5EpGEpDlciIndex Integer32

McsMgrFrf5EpGEpDlciOperEntry  
SEQUENCE    
  mcsMgrFrf5EpGEpDlciABitStatusToIf INTEGER
  mcsMgrFrf5EpGEpDlciABitReasonToIf INTEGER
  mcsMgrFrf5EpGEpDlciABitStatusFromIf INTEGER
  mcsMgrFrf5EpGEpDlciABitReasonFromIf INTEGER
  mcsMgrFrf5EpGEpDlciAccessConnectionComponent AsciiString

McsMgrFrf5EpGEpAtmConRowStatusEntry  
SEQUENCE    
  mcsMgrFrf5EpGEpAtmConRowStatus RowStatus
  mcsMgrFrf5EpGEpAtmConComponentName DisplayString
  mcsMgrFrf5EpGEpAtmConStorageType StorageType
  mcsMgrFrf5EpGEpAtmConIndex NonReplicated

McsMgrFrf5EpGEpAtmConOperEntry  
SEQUENCE    
  mcsMgrFrf5EpGEpAtmConNextHop RowPointer

Defined Values

frf5EpMIB 1.3.6.1.4.1.562.2.4.2.121
OBJECT IDENTIFIER    

mcsMgrFrf5EpG 1.3.6.1.4.1.562.2.4.1.122.14
OBJECT IDENTIFIER    

mcsMgrFrf5EpGRowStatusTable 1.3.6.1.4.1.562.2.4.1.122.14.1
This entry controls the addition and deletion of mcsMgrFrf5EpG components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    McsMgrFrf5EpGRowStatusEntry

mcsMgrFrf5EpGRowStatusEntry 1.3.6.1.4.1.562.2.4.1.122.14.1.1
A single entry in the table represents a single mcsMgrFrf5EpG component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  McsMgrFrf5EpGRowStatusEntry  

mcsMgrFrf5EpGRowStatus 1.3.6.1.4.1.562.2.4.1.122.14.1.1.1
This variable is used as the basis for SNMP naming of mcsMgrFrf5EpG components. These components can be added and deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

mcsMgrFrf5EpGComponentName 1.3.6.1.4.1.562.2.4.1.122.14.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

mcsMgrFrf5EpGStorageType 1.3.6.1.4.1.562.2.4.1.122.14.1.1.4
This variable represents the storage type value for the mcsMgrFrf5EpG tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

mcsMgrFrf5EpGIndex 1.3.6.1.4.1.562.2.4.1.122.14.1.1.10
This variable represents the index for the mcsMgrFrf5EpG tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Integer32 1..8191  

mcsMgrFrf5EpGAddr 1.3.6.1.4.1.562.2.4.1.122.14.2
OBJECT IDENTIFIER    

mcsMgrFrf5EpGAddrRowStatusTable 1.3.6.1.4.1.562.2.4.1.122.14.2.1
This entry controls the addition and deletion of mcsMgrFrf5EpGAddr components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    McsMgrFrf5EpGAddrRowStatusEntry

mcsMgrFrf5EpGAddrRowStatusEntry 1.3.6.1.4.1.562.2.4.1.122.14.2.1.1
A single entry in the table represents a single mcsMgrFrf5EpGAddr component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  McsMgrFrf5EpGAddrRowStatusEntry  

mcsMgrFrf5EpGAddrRowStatus 1.3.6.1.4.1.562.2.4.1.122.14.2.1.1.1
This variable is used as the basis for SNMP naming of mcsMgrFrf5EpGAddr components. These components cannot be added nor deleted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RowStatus  

mcsMgrFrf5EpGAddrComponentName 1.3.6.1.4.1.562.2.4.1.122.14.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

mcsMgrFrf5EpGAddrStorageType 1.3.6.1.4.1.562.2.4.1.122.14.2.1.1.4
This variable represents the storage type value for the mcsMgrFrf5EpGAddr tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

mcsMgrFrf5EpGAddrIndex 1.3.6.1.4.1.562.2.4.1.122.14.2.1.1.10
This variable represents the index for the mcsMgrFrf5EpGAddr tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

mcsMgrFrf5EpGAddrProvTable 1.3.6.1.4.1.562.2.4.1.122.14.2.10
This group contains the provisionable attributes of the Address component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    McsMgrFrf5EpGAddrProvEntry

mcsMgrFrf5EpGAddrProvEntry 1.3.6.1.4.1.562.2.4.1.122.14.2.10.1
An entry in the mcsMgrFrf5EpGAddrProvTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  McsMgrFrf5EpGAddrProvEntry  

mcsMgrFrf5EpGAddrRemoteAddress 1.3.6.1.4.1.562.2.4.1.122.14.2.10.1.1
This attribute specifies the ATM End System Address (AESA) in the ISO NSAP format that is used by each EndPoint under this Frf5EpG to establish a VCC. For example, NSAP ATM address '45000006138292323F000000000020480D002900'.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AsciiString Size(0..44)  

mcsMgrFrf5EpGAddrCommentText 1.3.6.1.4.1.562.2.4.1.122.14.2.10.1.2
This optional attribute contains additional textual information to be added by the network operator.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AsciiString Size(0..750)  

mcsMgrFrf5EpGAddrAddrPreTable 1.3.6.1.4.1.562.2.4.1.122.14.2.362
This attribute specifies the list of prefixes directed to the EndPoints under this Frf5EndPointGroup. The individual end point is selected for each subconnection on the basis of its supportedTransferPriorities. For example, E.164 prefix 'e.613722', X.121 prefix 'x.302'.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    McsMgrFrf5EpGAddrAddrPreEntry

mcsMgrFrf5EpGAddrAddrPreEntry 1.3.6.1.4.1.562.2.4.1.122.14.2.362.1
An entry in the mcsMgrFrf5EpGAddrAddrPreTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  McsMgrFrf5EpGAddrAddrPreEntry  

mcsMgrFrf5EpGAddrAddrPreValue 1.3.6.1.4.1.562.2.4.1.122.14.2.362.1.1
This variable represents both the value and the index for the mcsMgrFrf5EpGAddrAddrPreTable.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AsciiString Size(3..17)  

mcsMgrFrf5EpGAddrAddrPreRowStatus 1.3.6.1.4.1.562.2.4.1.122.14.2.362.1.2
This variable is used to control the addition and deletion of individual values of the mcsMgrFrf5EpGAddrAddrPreTable.
Status: mandatory Access: write-only
OBJECT-TYPE    
  RowStatus  

mcsMgrFrf5EpGEp 1.3.6.1.4.1.562.2.4.1.122.14.3
OBJECT IDENTIFIER    

mcsMgrFrf5EpGEpRowStatusTable 1.3.6.1.4.1.562.2.4.1.122.14.3.1
This entry controls the addition and deletion of mcsMgrFrf5EpGEp components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    McsMgrFrf5EpGEpRowStatusEntry

mcsMgrFrf5EpGEpRowStatusEntry 1.3.6.1.4.1.562.2.4.1.122.14.3.1.1
A single entry in the table represents a single mcsMgrFrf5EpGEp component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  McsMgrFrf5EpGEpRowStatusEntry  

mcsMgrFrf5EpGEpRowStatus 1.3.6.1.4.1.562.2.4.1.122.14.3.1.1.1
This variable is used as the basis for SNMP naming of mcsMgrFrf5EpGEp components. These components can be added and deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

mcsMgrFrf5EpGEpComponentName 1.3.6.1.4.1.562.2.4.1.122.14.3.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

mcsMgrFrf5EpGEpStorageType 1.3.6.1.4.1.562.2.4.1.122.14.3.1.1.4
This variable represents the storage type value for the mcsMgrFrf5EpGEp tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

mcsMgrFrf5EpGEpIndex 1.3.6.1.4.1.562.2.4.1.122.14.3.1.1.10
This variable represents the index for the mcsMgrFrf5EpGEp tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Integer32 0..15  

mcsMgrFrf5EpGEpStateTable 1.3.6.1.4.1.562.2.4.1.122.14.3.10
This group contains the three OSI State attributes and the six OSI Status attributes. The descriptions generically indicate what each attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241- 7001-150, Passport Operations and Maintenance Guide.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    McsMgrFrf5EpGEpStateEntry

mcsMgrFrf5EpGEpStateEntry 1.3.6.1.4.1.562.2.4.1.122.14.3.10.1
An entry in the mcsMgrFrf5EpGEpStateTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  McsMgrFrf5EpGEpStateEntry  

mcsMgrFrf5EpGEpAdminState 1.3.6.1.4.1.562.2.4.1.122.14.3.10.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

mcsMgrFrf5EpGEpOperationalState 1.3.6.1.4.1.562.2.4.1.122.14.3.10.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mcsMgrFrf5EpGEpUsageState 1.3.6.1.4.1.562.2.4.1.122.14.3.10.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

mcsMgrFrf5EpGEpAvailabilityStatus 1.3.6.1.4.1.562.2.4.1.122.14.3.10.1.4
If supported by the component, this attribute indicates the OSI Availability status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value inTest indicates that the resource is undergoing a test procedure. If adminState is locked or shuttingDown, the normal users are precluded from using the resource and controlStatus is reservedForTest. Tests that do not exclude additional users can be present in any operational or administrative state but the reservedForTest condition should not be present. The value failed indicates that the component has an internal fault that prevents it from operating. The operationalState is disabled. The value dependency indicates that the component cannot operate because some other resource on which it depends is unavailable. The operationalState is disabled. The value powerOff indicates the resource requires power to be applied and it is not powered on. The operationalState is disabled. The value offLine indicates the resource requires a routine operation (either manual, automatic, or both) to be performed to place it on-line and make it available for use. The operationalState is disabled. The value offDuty indicates the resource is inactive in accordance with a predetermined time schedule. In the absence of other disabling conditions, the operationalState is enabled or disabled. The value degraded indicates the service provided by the component is degraded in some way, such as in speed or operating capacity. However, the resource remains available for service. The operationalState is enabled. The value notInstalled indicates the resource is not present. The operationalState is disabled. The value logFull is not used. Description of bits: inTest(0) failed(1) powerOff(2) offLine(3) offDuty(4) dependency(5) degraded(6) notInstalled(7) logFull(8)
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2)  

mcsMgrFrf5EpGEpProceduralStatus 1.3.6.1.4.1.562.2.4.1.122.14.3.10.1.5
If supported by the component, this attribute indicates the OSI Procedural status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value initializationRequired indicates (for a resource which doesn't initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState is disabled. The value notInitialized indicates (for a resource which does initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState may be enabled or disabled. The value initializing indicates that initialization has been initiated but is not yet complete. The operationalState may be enabled or disabled. The value reporting indicates the resource has completed some processing operation and is notifying the results. The operationalState is enabled. The value terminating indicates the component is in a termination phase. If the resource doesn't reinitialize autonomously, operationalState is disabled; otherwise it is enabled or disabled. Description of bits: initializationRequired(0) notInitialized(1) initializing(2) reporting(3) terminating(4)
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

mcsMgrFrf5EpGEpControlStatus 1.3.6.1.4.1.562.2.4.1.122.14.3.10.1.6
If supported by the component, this attribute indicates the OSI Control status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value subjectToTest indicates the resource is available but tests may be conducted simultaneously at unpredictable times, which may cause it to exhibit unusual characteristics. The value partOfServicesLocked indicates that part of the service is restricted from users of a resource. The adminState is unlocked. The value reservedForTest indicates that the component is administratively unavailable because it is undergoing a test procedure. The adminState is locked. The value suspended indicates that the service has been administratively suspended. Description of bits: subjectToTest(0) partOfServicesLocked(1) reservedForTest(2) suspended(3)
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

mcsMgrFrf5EpGEpAlarmStatus 1.3.6.1.4.1.562.2.4.1.122.14.3.10.1.7
If supported by the component, this attribute indicates the OSI Alarm status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value underRepair indicates the component is currently being repaired. The operationalState is enabled or disabled. The value critical indicates one or more critical alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value major indicates one or more major alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value minor indicates one or more minor alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value alarmOutstanding generically indicates that an alarm of some severity is outstanding against the component. Description of bits: underRepair(0) critical(1) major(2) minor(3) alarmOutstanding(4)
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

mcsMgrFrf5EpGEpStandbyStatus 1.3.6.1.4.1.562.2.4.1.122.14.3.10.1.8
If supported by the component, this attribute indicates the OSI Standby status of the component. The value notSet indicates that either the attribute is not supported or that none of the status conditions described below are present. Note that this is a non-standard value, used because the original specification indicated this attribute was set-valued and thus, did not provide a value to indicate that none of the other three are applicable. The value hotStandby indicates that the resource is not providing service but will be immediately able to take over the role of the resource to be backed up, without initialization activity, and containing the same information as the resource to be backed up. The value coldStandby indicates the resource is a backup for another resource but will not be immediately able to take over the role of the backed up resource and will require some initialization activity. The value providingService indicates that this component, as a backup resource, is currently backing up another resource.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER hotStandby(0), coldStandby(1), providingService(2), notSet(15)  

mcsMgrFrf5EpGEpUnknownStatus 1.3.6.1.4.1.562.2.4.1.122.14.3.10.1.9
This attribute indicates the OSI Unknown status of the component. The value false indicates that all of the other OSI State and Status attribute values can be considered accurate. The value true indicates that the actual state of the component is not known for sure.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER false(0), true(1)  

mcsMgrFrf5EpGEpOperTable 1.3.6.1.4.1.562.2.4.1.122.14.3.11
This group contains the operational attributes for the FRF.5 ATM connection.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    McsMgrFrf5EpGEpOperEntry

mcsMgrFrf5EpGEpOperEntry 1.3.6.1.4.1.562.2.4.1.122.14.3.11.1
An entry in the mcsMgrFrf5EpGEpOperTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  McsMgrFrf5EpGEpOperEntry  

mcsMgrFrf5EpGEpLastVccClearCause 1.3.6.1.4.1.562.2.4.1.122.14.3.11.1.4
This attribute indicates the clear cause value of the last SPVC release message received on the FRF.5 end point Vcc pipe.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..255  

mcsMgrFrf5EpGEpConnectionTransferPriority 1.3.6.1.4.1.562.2.4.1.122.14.3.11.1.5
This attribute indicates the transfer priority used to establish the ATM connection and to multiplex the Frame Relay DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..15  

mcsMgrFrf5EpGEpServiceCategory 1.3.6.1.4.1.562.2.4.1.122.14.3.11.1.6
This attribute indicates the ATM service category that is used for this connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ubr(0), cbr(1), rtVbr(2), nrtVbr(3)  

mcsMgrFrf5EpGEpPeakCellRate01 1.3.6.1.4.1.562.2.4.1.122.14.3.11.1.8
This attribute indicates the Peak Cell Rate (PCR) of the FRF.5 ATM VCC for all cells (with CLP=0 and CLP=1). The pcr01 is derived from the End Point traffic parameters using the conversion policy of the connectionTransferPriority. The conversion policy is defined under the ModuleData FrameRelayService AtmNetworking TransferPriority/n component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mcsMgrFrf5EpGEpSustainedCellRate0 1.3.6.1.4.1.562.2.4.1.122.14.3.11.1.9
This attribute indicates the Sustained Cell Rate (SCR) of the FRF.5 ATM VCC for high priority cells (with CLP=0). The scr0 is derived from the End Point traffic parameters using the conversion policy of the connectionTransferPriority. The conversion policy is defined under the ModuleData FrameRelayService AtmNetworking TransferPriority/n component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mcsMgrFrf5EpGEpSustainedCellRate01 1.3.6.1.4.1.562.2.4.1.122.14.3.11.1.10
This attribute indicates the Sustained Cell Rate (SCR) of the FRF.5 ATM VCC for all cells (with CLP=0 and CLP=1). The scr01 is derived from the End Point traffic parameters using the conversion policy of the connectionTransferPriority. The conversion policy is defined under the ModuleData FrameRelayService AtmNetworking TransferPriority/n component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mcsMgrFrf5EpGEpMaximumBurstSize0 1.3.6.1.4.1.562.2.4.1.122.14.3.11.1.11
This attribute indicates the Maximum Burst Size (MBS) of the FRF.5 ATM VCC for high priority cells (with CLP=0). The mbs0 is derived from the End Point traffic parameters using the conversion policy of the connectionTransferPriority. The conversion policy is defined under the ModuleData FrameRelayService AtmNetworking TransferPriority/n component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mcsMgrFrf5EpGEpMaximumBurstSize01 1.3.6.1.4.1.562.2.4.1.122.14.3.11.1.12
This attribute indicates the Maximum Burst Size (MBS) of the FRF.5 ATM VCC for all cells (with CLP=0 and CLP=1). The mbs01 is derived from the End Point traffic parameters using the conversion policy of the connectionTransferPriority. The conversion policy is defined under the ModuleData FrameRelayService AtmNetworking TransferPriority/n component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mcsMgrFrf5EpGEpAvgFrameSize 1.3.6.1.4.1.562.2.4.1.122.14.3.11.1.13
This attribute indicates the average frame size that is used in the traffic parameter conversion policy calculations for this end point.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32 1..8187  

mcsMgrFrf5EpGEpTrafficParmConversionPolicy 1.3.6.1.4.1.562.2.4.1.122.14.3.11.1.14
This attribute indicates the traffic parameter conversion policy used to specify the equivalent ATM bandwidth rate at this end point. Policy 3 characterizes the traffic in the following way: - ATM traffic descriptor type 6 is selected - PCR0+1 is based on the AR - SCR0+1 is based on the CIR and EIR - MBS0+1 is based on Bc,Be,CIR,EIR and AR - Takes into account that the instananeous rate of the frame relay stream can burst above CIR and up tp the AR. Policy 4 characterizes the traffic in the following way: - ATM traffic descriptor type 7 or 8 is selected. Type 7 is chosen when non-conforming cells are to be discarded and type 8 when non-conforming cells are tagged by UPC traffic policer. - PCR0+1 is based on the AR - SCR0 is based on the CIR - MBS0 is based on Bc,CIR and AR - There is no direct characterization of EIR. The allowed EIR can be derived using the difference between the AR and CIR. Policy 5 characterizes the traffic in the following way: - ATM traffic descriptor type 7 or 8 is selected . Type 7 is chosen when non-conforming cells are to be discarded and type 8 when non-conforming cells are tagged by UPC traffic policer - PCR0+1 is based on CIR and EIR - SCR0 is based on the CIR - MBS0 is based on the Bc,CIR and AR - The maximum PCR is no longer based on AR but based on the CIR and EIR. Policy 6 characterizes the traffic in the following way: - ATM traffic descriptor type 3 is selected - PCR0+1 is based only on CIR.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER n3(3), n4(4), n5(5), n6(6)  

mcsMgrFrf5EpGEpType 1.3.6.1.4.1.562.2.4.1.122.14.3.11.1.15
This attribute indicates the FRF.5 End Point type. If the value is master, this End Point is responsible for initiating the call to set up the FRF.5 ATM VCC. If the value is slave, this End Point receives call setup requests from the remote end.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER master(0), slave(1)  

mcsMgrFrf5EpGEpLastVccCauseDiag 1.3.6.1.4.1.562.2.4.1.122.14.3.11.1.20
This attribute indicates the diagnostic value of the last SPVC release message received on the FRF.5 end point Vcc pipe.
Status: mandatory Access: read-only
OBJECT-TYPE    
  HexString Size(1..8)  

mcsMgrFrf5EpGEpLmi 1.3.6.1.4.1.562.2.4.1.122.14.3.2
OBJECT IDENTIFIER    

mcsMgrFrf5EpGEpLmiRowStatusTable 1.3.6.1.4.1.562.2.4.1.122.14.3.2.1
This entry controls the addition and deletion of mcsMgrFrf5EpGEpLmi components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    McsMgrFrf5EpGEpLmiRowStatusEntry

mcsMgrFrf5EpGEpLmiRowStatusEntry 1.3.6.1.4.1.562.2.4.1.122.14.3.2.1.1
A single entry in the table represents a single mcsMgrFrf5EpGEpLmi component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  McsMgrFrf5EpGEpLmiRowStatusEntry  

mcsMgrFrf5EpGEpLmiRowStatus 1.3.6.1.4.1.562.2.4.1.122.14.3.2.1.1.1
This variable is used as the basis for SNMP naming of mcsMgrFrf5EpGEpLmi components. These components can be added and deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

mcsMgrFrf5EpGEpLmiComponentName 1.3.6.1.4.1.562.2.4.1.122.14.3.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

mcsMgrFrf5EpGEpLmiStorageType 1.3.6.1.4.1.562.2.4.1.122.14.3.2.1.1.4
This variable represents the storage type value for the mcsMgrFrf5EpGEpLmi tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

mcsMgrFrf5EpGEpLmiIndex 1.3.6.1.4.1.562.2.4.1.122.14.3.2.1.1.10
This variable represents the index for the mcsMgrFrf5EpGEpLmi tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

mcsMgrFrf5EpGEpLmiParmsTable 1.3.6.1.4.1.562.2.4.1.122.14.3.2.10
This group contains the provisionable attributes of the Local Management Interface component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    McsMgrFrf5EpGEpLmiParmsEntry

mcsMgrFrf5EpGEpLmiParmsEntry 1.3.6.1.4.1.562.2.4.1.122.14.3.2.10.1
An entry in the mcsMgrFrf5EpGEpLmiParmsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  McsMgrFrf5EpGEpLmiParmsEntry  

mcsMgrFrf5EpGEpLmiProcedures 1.3.6.1.4.1.562.2.4.1.122.14.3.2.10.1.1
This attribute selects the procedures to be used for the Local Management Interface. The following are the supported procedures: none: no Local Management Interface procedures are running on the ATM VCC. This accomodates remote interworking functions which do not implement LMI procedures. In this case, the remaining attributes of this group will be ignored. ccitt: Local Management Interface procedures from the CCITT specification are supported. Dlci/0 is used for the LMI protocol, to comply with FRF.5. ansi: Local Management Interface procedures from the ANSI specification are supported. DLCI 0 is used for the LMI protocol.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(0), ansi(2), ccitt(3)  

mcsMgrFrf5EpGEpLmiAsyncStatusReport 1.3.6.1.4.1.562.2.4.1.122.14.3.2.10.1.2
This attribute selects the use of asynchronous PVC status report procedures as specified in the CCITT specification (ITU-T Q.933, Annex A), and the ANSI specification Annex D.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER off(0), on(1)  

mcsMgrFrf5EpGEpLmiErrorEventThreshold 1.3.6.1.4.1.562.2.4.1.122.14.3.2.10.1.3
For the network side procedure, an event is defined as follows: (1) receipt of a STATUS ENQUIRY message, or (2) expiration of timer T392. An error event is (1) nonreceipt of STATUS ENQUIRY in T392 seconds; (2) invalid format of an LMI message; (3) invalid receive sequence number. For the user side procedure, an event is defined as a polling cycle or a status enquiry and status report exchange. An error event is (1) non-receipt of a STATUS within the polling cycle, or (2) invalid format of an LMI message, or (3) invalid sequence number. This attribute specifies the number of error events which, if they occur within eventCount events, will cause a protocol error condition. The condition is cleared after eventCount sequential correct events occur. It must be less than or equal to eventCount (n393).
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1..10  

mcsMgrFrf5EpGEpLmiEventCount 1.3.6.1.4.1.562.2.4.1.122.14.3.2.10.1.4
This attribute specifies the number of contiguous events within which no more than eventErrorThreshold error events are allowed. It must be greater than or equal to errorEventThreshold (n392).
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1..10  

mcsMgrFrf5EpGEpLmiCheckPointTimer 1.3.6.1.4.1.562.2.4.1.122.14.3.2.10.1.5
This attribute selects the time (in seconds) within which a STATUS ENQUIRY message is expected. It must be greater than linkVerificationTimer (t391).
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 5..255  

mcsMgrFrf5EpGEpLmiSide 1.3.6.1.4.1.562.2.4.1.122.14.3.2.10.1.8
This attribute selects the user side procedure (DTE), or the network side procedure (DCE), or both the user side and the network side procedures of the LMI. This attribute can be set to user, network or both.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER network(0), user(1), both(2)  

mcsMgrFrf5EpGEpLmiNniParmsTable 1.3.6.1.4.1.562.2.4.1.122.14.3.2.11
This group contains the provisionable attributes of the FRF.5 LMI procedures which are unique to NNI.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    McsMgrFrf5EpGEpLmiNniParmsEntry

mcsMgrFrf5EpGEpLmiNniParmsEntry 1.3.6.1.4.1.562.2.4.1.122.14.3.2.11.1
An entry in the mcsMgrFrf5EpGEpLmiNniParmsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  McsMgrFrf5EpGEpLmiNniParmsEntry  

mcsMgrFrf5EpGEpLmiFullStatusPollingCycles 1.3.6.1.4.1.562.2.4.1.122.14.3.2.11.1.1
This attribute specifies how frequently the FRF.5 LMI initiates a Status Enquiry for a full PVC status report. A polling cycle is a Status Enquiry and Status Report exchange.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 1..255  

mcsMgrFrf5EpGEpLmiLinkVerificationTimer 1.3.6.1.4.1.562.2.4.1.122.14.3.2.11.1.2
This attribute specifies how frequently the FRF.5 LMI initiates a Status Enquiry for link integrity verification. It must be less than checkPointTimer (t392).
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 5..255  

mcsMgrFrf5EpGEpLmiStateTable 1.3.6.1.4.1.562.2.4.1.122.14.3.2.12
This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    McsMgrFrf5EpGEpLmiStateEntry

mcsMgrFrf5EpGEpLmiStateEntry 1.3.6.1.4.1.562.2.4.1.122.14.3.2.12.1
An entry in the mcsMgrFrf5EpGEpLmiStateTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  McsMgrFrf5EpGEpLmiStateEntry  

mcsMgrFrf5EpGEpLmiAdminState 1.3.6.1.4.1.562.2.4.1.122.14.3.2.12.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

mcsMgrFrf5EpGEpLmiOperationalState 1.3.6.1.4.1.562.2.4.1.122.14.3.2.12.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mcsMgrFrf5EpGEpLmiUsageState 1.3.6.1.4.1.562.2.4.1.122.14.3.2.12.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

mcsMgrFrf5EpGEpLmiPsiTable 1.3.6.1.4.1.562.2.4.1.122.14.3.2.13
This group provides the protocol status of the Local Management Interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    McsMgrFrf5EpGEpLmiPsiEntry

mcsMgrFrf5EpGEpLmiPsiEntry 1.3.6.1.4.1.562.2.4.1.122.14.3.2.13.1
An entry in the mcsMgrFrf5EpGEpLmiPsiTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  McsMgrFrf5EpGEpLmiPsiEntry  

mcsMgrFrf5EpGEpLmiProtocolStatus 1.3.6.1.4.1.562.2.4.1.122.14.3.2.13.1.1
This attribute indicates whether the LMI is in an error condition or whether the protocol is behaving normally. This attribute will be set to errorCondition after enough LMI errors have been detected to warrant a change in condition. This occurs when n392 of the last n393 events are in error. The error condition is lifted when a sufficient number of consecutive events has occurred without error. This occurs when n393 consecutive good events take place. The consequence of an error condition is that all DLCIs on this interface will become inactive in both directions.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER errorCondition(0), normalCondition(1)  

mcsMgrFrf5EpGEpLmiStatsTable 1.3.6.1.4.1.562.2.4.1.122.14.3.2.14
This group contains the operational statistics for the FRF.5 NNI Local Management Interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    McsMgrFrf5EpGEpLmiStatsEntry

mcsMgrFrf5EpGEpLmiStatsEntry 1.3.6.1.4.1.562.2.4.1.122.14.3.2.14.1
An entry in the mcsMgrFrf5EpGEpLmiStatsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  McsMgrFrf5EpGEpLmiStatsEntry  

mcsMgrFrf5EpGEpLmiKeepAliveStatusToInterface 1.3.6.1.4.1.562.2.4.1.122.14.3.2.14.1.1
This attribute counts the Local Management Interface keep alive status messages sent to the ATM VCC in response to a status enquiry for keep alive status. When the maximum count is reached it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mcsMgrFrf5EpGEpLmiFullStatusToInterface 1.3.6.1.4.1.562.2.4.1.122.14.3.2.14.1.2
This attribute counts the Local Management Interface full status messages sent to the ATM VCC in response to a status enquiry for keep alive or full status. When the maximum count is reached it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mcsMgrFrf5EpGEpLmiKeepAliveStatusEnqFromInterface 1.3.6.1.4.1.562.2.4.1.122.14.3.2.14.1.3
This attribute counts the Local Management Interface valid keep alive status enquiry messages received from the ATM VCC. When the maximum count is reached it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mcsMgrFrf5EpGEpLmiFullStatusEnqFromInterface 1.3.6.1.4.1.562.2.4.1.122.14.3.2.14.1.4
This attribute counts the Local Management Interface valid full status enquiry messages received from the ATM VCC. When the maximum count is reached it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mcsMgrFrf5EpGEpLmiNetworkSideEventHistory 1.3.6.1.4.1.562.2.4.1.122.14.3.2.14.1.5
This attribute displays the Local Management Interface network side procedure event history in order of occurrence. An event is represented by a single symbol. A '+' symbol indicates a good event. An 'X' symbol indicates a protocol error event. The left most event is the most recent to occur. The provisioned eventCount dictates the maximum number of events displayed. A good event is triggered by receipt of a valid status enquiry message. An error event is either a T392 timer expiry or receipt of a status enquiry with an incorrect sequence number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AsciiString Size(1..10)  

mcsMgrFrf5EpGEpLmiUserSideEventHistory 1.3.6.1.4.1.562.2.4.1.122.14.3.2.14.1.6
This attribute displays the Local Management Interface user side procedure event history in order of occurrence. An event is represented by a single symbol. A '+' symbol indicates a good event. An 'X' symbol indicates a protocol error event. The left most event is the most recent to occur. The provisioned eventCount dictates the maximum number of events displayed. A good event is triggered by receipt of a valid status message. An error event is either a T391 timer expiry or receipt of a status message with an incorrect sequence number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AsciiString Size(1..10)  

mcsMgrFrf5EpGEpLmiProtocolErrors 1.3.6.1.4.1.562.2.4.1.122.14.3.2.14.1.7
This attribute counts the number of Local Management Interface protocol errors. It is the sum of the sequence (sequenceErrors and statusSequenceErrors) and timeout (pollingVerifTimeouts and noStatusReportCount) errors. When the maximum count is reached it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mcsMgrFrf5EpGEpLmiUnexpectedIes 1.3.6.1.4.1.562.2.4.1.122.14.3.2.14.1.8
This attribute counts the number of Local Managament Interface frames received with an Information Element identifier that is unknown or unexpected. An unexpected Information Element is not a protocol error. When the maximum count is reached, this counter wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mcsMgrFrf5EpGEpLmiSequenceErrors 1.3.6.1.4.1.562.2.4.1.122.14.3.2.14.1.9
This attribute counts the number of Local Management Interface Status Enquiry message sequence errors. A sequence error is receipt of a Status Enquiry message with a receive sequence number not equal to the last send sequence number. When the maximum count is reached the counter wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mcsMgrFrf5EpGEpLmiStatusSequenceErrors 1.3.6.1.4.1.562.2.4.1.122.14.3.2.14.1.10
This attribute counts the number of Local Management Interface Status message sequence errors. A sequence error is receipt of a Status message with a receive sequence number not equal to the last send sequence number. When the maximum count is reached the counter wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mcsMgrFrf5EpGEpLmiUnexpectedReports 1.3.6.1.4.1.562.2.4.1.122.14.3.2.14.1.11
This attribute counts the number of Local Management Interface frames received with an unknown or unexpected report type. An unexpected report type is not a protocol error. When the maximum count is reached the counter wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mcsMgrFrf5EpGEpLmiPollingVerifTimeouts 1.3.6.1.4.1.562.2.4.1.122.14.3.2.14.1.12
This attribute counts the checkPointTimer (T392) expiries occurring on the Local Management Interface. When the maximum count is reached the counter wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mcsMgrFrf5EpGEpLmiNoStatusReportCount 1.3.6.1.4.1.562.2.4.1.122.14.3.2.14.1.13
This attribute counts the number of times when no status report or an invalid status report comes from the external network. This attribute is incremented: i) after a status enquiry is sent out and the T391 timer expires without having a status report received. ii) if an invalid status report is received. When the maximum count is reached it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mcsMgrFrf5EpGEpLmiKeepAliveEnqToIf 1.3.6.1.4.1.562.2.4.1.122.14.3.2.14.1.14
This attribute counts the number of Local Management Interface keep alive enquiry status messages sent to the external user device for keep alive status. When the maximum count is reached it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mcsMgrFrf5EpGEpLmiFullStatusEnqToIf 1.3.6.1.4.1.562.2.4.1.122.14.3.2.14.1.15
This attribute counts the number of Local Management Interface full status messages sent to the external user device in response to a status enquiry for keep alive or full status. When the maximum count is reached it wraps to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter32  

mcsMgrFrf5EpGEpEpd 1.3.6.1.4.1.562.2.4.1.122.14.3.3
OBJECT IDENTIFIER    

mcsMgrFrf5EpGEpEpdRowStatusTable 1.3.6.1.4.1.562.2.4.1.122.14.3.3.1
This entry controls the addition and deletion of mcsMgrFrf5EpGEpEpd components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    McsMgrFrf5EpGEpEpdRowStatusEntry

mcsMgrFrf5EpGEpEpdRowStatusEntry 1.3.6.1.4.1.562.2.4.1.122.14.3.3.1.1
A single entry in the table represents a single mcsMgrFrf5EpGEpEpd component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  McsMgrFrf5EpGEpEpdRowStatusEntry  

mcsMgrFrf5EpGEpEpdRowStatus 1.3.6.1.4.1.562.2.4.1.122.14.3.3.1.1.1
This variable is used as the basis for SNMP naming of mcsMgrFrf5EpGEpEpd components. These components cannot be added nor deleted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RowStatus  

mcsMgrFrf5EpGEpEpdComponentName 1.3.6.1.4.1.562.2.4.1.122.14.3.3.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

mcsMgrFrf5EpGEpEpdStorageType 1.3.6.1.4.1.562.2.4.1.122.14.3.3.1.1.4
This variable represents the storage type value for the mcsMgrFrf5EpGEpEpd tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

mcsMgrFrf5EpGEpEpdIndex 1.3.6.1.4.1.562.2.4.1.122.14.3.3.1.1.10
This variable represents the index for the mcsMgrFrf5EpGEpEpd tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

mcsMgrFrf5EpGEpEpdProvTable 1.3.6.1.4.1.562.2.4.1.122.14.3.3.10
This group contains the provisionable attributes of the FRF.5 End Point.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    McsMgrFrf5EpGEpEpdProvEntry

mcsMgrFrf5EpGEpEpdProvEntry 1.3.6.1.4.1.562.2.4.1.122.14.3.3.10.1
An entry in the mcsMgrFrf5EpGEpEpdProvTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  McsMgrFrf5EpGEpEpdProvEntry  

mcsMgrFrf5EpGEpEpdRemoteConnectionIdentifier 1.3.6.1.4.1.562.2.4.1.122.14.3.3.10.1.3
This attribute specifies the remote connection identifier. It either represents the VPI.VCI logical channel number assignment of a remote ATM interface, or the Endpoint.Frf5EndPointGroup instances of a remote Passport FRF.5 EndPoint.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IntegerSequence Size(3..9)  

mcsMgrFrf5EpGEpEpdConnectionTransferPriority 1.3.6.1.4.1.562.2.4.1.122.14.3.3.10.1.4
This attribute specifies the transfer priority used to establish the ATM connection. The EndPoint references the ModuleData FrameRelayService AtmNetworking TransferPriority/n component to determine the ATM service category to be used by the connection. This attribute is also used to determine which EndPoint within an Frf5EndPointGroup is to multiplex a particular FrAtm Dlci. DESCRIPTION
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..15  

mcsMgrFrf5EpGEpEpdCommittedInformationRate 1.3.6.1.4.1.562.2.4.1.122.14.3.3.10.1.5
This attribute specifies the committed information rate (CIR), and represents the rate at which the network FRF.5 ATM VCC agrees to transfer information under normal conditions. A conservative CIR value would be the sum of the CIRs of all the individual FrAtm Dlcis multiplexed by the VCC. The cir is converted into ATM service parameters according to the conversion policy specified by the connectionTransferPriority attribute. The conversion policy is defined under the ModuleData FrameRelayService AtmNetworking TransferPriority/n component.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..50000000  

mcsMgrFrf5EpGEpEpdExcessInformationRate 1.3.6.1.4.1.562.2.4.1.122.14.3.3.10.1.6
This attribute specifies the excess information rate (EIR), and represents the rate at which the network FRF.5 ATM VCC attempts to transfer information. A conservative EIR value would be the sum of the EIRs of all the individual FrAtm Dlcis multiplexed by the VCC. The eir is converted into ATM service parameters according to the conversion policy specified by the connectionTransferPriority attribute. The conversion policy is defined under the ModuleData FrameRelayService AtmNetworking TransferPriority/n component.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..50000000  

mcsMgrFrf5EpGEpEpdCommittedBurstSize 1.3.6.1.4.1.562.2.4.1.122.14.3.3.10.1.7
This attribute specifies the committed burst size (Bc), and represents the amount of data that the network FRF.5 ATM VCC agrees to transfer under normal conditions. A conservative Bc value would be the sum of the Bcs of all the individual FrAtm Dlcis multiplexed by the VCC. The bc is converted into ATM service parameters according to the conversion policy specified by the connectionTransferPriority attribute. The conversion policy is defined under the ModuleData FrameRelayService AtmNetworking TransferPriority/n component.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..50000000  

mcsMgrFrf5EpGEpEpdType 1.3.6.1.4.1.562.2.4.1.122.14.3.3.10.1.8
This attribute specifies the FRF.5 End Point type. If the value is provisioned as master, this End Point is responsible for initiating the SPVC call to set up the FRF.5 ATM VCC. If the value is provisioned as slave, this End Point receives call setup requests from a master remote end.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER master(0), slave(1)  

mcsMgrFrf5EpGEpEpdAccessRate 1.3.6.1.4.1.562.2.4.1.122.14.3.3.10.1.9
This attribute represents the access rate of the FRF.5 EndPoint. A conservative value would be the sum of the access rates of all the FrAtms' that have DLCIs multiplexed by the VCC. The access rate is converted into ATM service parameters when conversion policies 3, 4 and 5 are used. For policy 6, this attribute is ignored.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..50000000  

mcsMgrFrf5EpGEpEpdExcessBurstSize 1.3.6.1.4.1.562.2.4.1.122.14.3.3.10.1.10
This attribute specifies the excess burst size (Be), and represents the amount of uncommitted data that the network FRF.5 ATM VCC agrees to transfer under normal conditions. A conservative Be value would be the sum of the Bes of all the individual FrAtm Dlcis multiplexed by the VCC. The be is converted into ATM service parameters according to the conversion policy specified by the connectionTransferPriority attribute. The conversion policy is defined under the ModuleData FrameRelayService AtmNetworking TransferPriority/n component.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0..50000000  

mcsMgrFrf5EpGEpEpdCidDataTable 1.3.6.1.4.1.562.2.4.1.122.14.3.3.11
This group contains the attribute for a component's Customer Identifier (CID). Refer to the attribute description for a detailed explanation of CIDs.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    McsMgrFrf5EpGEpEpdCidDataEntry

mcsMgrFrf5EpGEpEpdCidDataEntry 1.3.6.1.4.1.562.2.4.1.122.14.3.3.11.1
An entry in the mcsMgrFrf5EpGEpEpdCidDataTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  McsMgrFrf5EpGEpEpdCidDataEntry  

mcsMgrFrf5EpGEpEpdCustomerIdentifier 1.3.6.1.4.1.562.2.4.1.122.14.3.3.11.1.1
This attribute holds the Customer Identifier (CID). Every component has a CID. If a component has a cid attribute, the component's CID is the provisioned value of that attribute; otherwise the component inherits the CID of its parent. The top- level component has a CID of 0. Every operator session also has a CID, which is the CID provisioned for the operator's user ID. An operator will see only the stream data for components having a matching CID. Also, the operator will be allowed to issue commands for only those components which have a matching CID. An operator CID of 0 is used to identify the Network Manager (referred to as 'NetMan' in DPN). This CID matches the CID of any component. Values 1 to 8191 inclusive (equivalent to 'basic CIDs' in DPN) may be assigned to specific customers.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Unsigned32 0 | 1..8191  

mcsMgrFrf5EpGEpDlci 1.3.6.1.4.1.562.2.4.1.122.14.3.4
OBJECT IDENTIFIER    

mcsMgrFrf5EpGEpDlciRowStatusTable 1.3.6.1.4.1.562.2.4.1.122.14.3.4.1
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This entry controls the addition and deletion of mcsMgrFrf5EpGEpDlci components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    McsMgrFrf5EpGEpDlciRowStatusEntry

mcsMgrFrf5EpGEpDlciRowStatusEntry 1.3.6.1.4.1.562.2.4.1.122.14.3.4.1.1
A single entry in the table represents a single mcsMgrFrf5EpGEpDlci component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  McsMgrFrf5EpGEpDlciRowStatusEntry  

mcsMgrFrf5EpGEpDlciRowStatus 1.3.6.1.4.1.562.2.4.1.122.14.3.4.1.1.1
This variable is used as the basis for SNMP naming of mcsMgrFrf5EpGEpDlci components. These components cannot be added nor deleted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RowStatus  

mcsMgrFrf5EpGEpDlciComponentName 1.3.6.1.4.1.562.2.4.1.122.14.3.4.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

mcsMgrFrf5EpGEpDlciStorageType 1.3.6.1.4.1.562.2.4.1.122.14.3.4.1.1.4
This variable represents the storage type value for the mcsMgrFrf5EpGEpDlci tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

mcsMgrFrf5EpGEpDlciIndex 1.3.6.1.4.1.562.2.4.1.122.14.3.4.1.1.10
This variable represents the index for the mcsMgrFrf5EpGEpDlci tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Integer32 16..1007 | 1022  

mcsMgrFrf5EpGEpDlciOperTable 1.3.6.1.4.1.562.2.4.1.122.14.3.4.10
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This group contains the operational attributes for the FRF.5 DLCI.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    McsMgrFrf5EpGEpDlciOperEntry

mcsMgrFrf5EpGEpDlciOperEntry 1.3.6.1.4.1.562.2.4.1.122.14.3.4.10.1
An entry in the mcsMgrFrf5EpGEpDlciOperTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  McsMgrFrf5EpGEpDlciOperEntry  

mcsMgrFrf5EpGEpDlciABitStatusToIf 1.3.6.1.4.1.562.2.4.1.122.14.3.4.10.1.1
This attribute indicates the most recent A-bit status sent to the ATM VCC. If the value is inactive, the reason for the LMI failure is given by the aBitReasonToNetwork.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER inactive(0), active(1)  

mcsMgrFrf5EpGEpDlciABitReasonToIf 1.3.6.1.4.1.562.2.4.1.122.14.3.4.10.1.2
This attribute indicates the reason for the latest inactive A-bit status sent to the ATM VCC. The value is notApplicable when the aBitStatusToNetwork is active. The value is remoteUserSignaled if the FrAtm originating the A-Bit status has detected that the virtual circuit is down at the remote network through the LMI protocol. The FrAtm must be running network site LMI protocol for this A-Bit status reason to be sent. The value is localLmiError if the LMI protocol is down at this Ep. The value is remoteLmiError if the LMI protocol is down at the FrAtm originating this A-Bit status reason. The value is localLinkDown if the physical interface is disabled at this Ep. The value is pvcDown if no A-Bit status has been sent to this Ep (i.e., no A-Bit status has been relayed from the FrAtm). The value is remoteLinkDown if the physical interface is disabled at the FrAtm originating this A-Bit status reason.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), remoteUserSignaled(1), localLmiError(2), remoteLmiError(3), localLinkDown(4), remoteLinkDown(5), pvcDown(6)  

mcsMgrFrf5EpGEpDlciABitStatusFromIf 1.3.6.1.4.1.562.2.4.1.122.14.3.4.10.1.3
This attribute indicates the most recent A-bit status received from the ATM VCC. If the value is inactive, the reason for the LMI failure is given by the aBitReasonFromNetwork.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER inactive(0), active(1)  

mcsMgrFrf5EpGEpDlciABitReasonFromIf 1.3.6.1.4.1.562.2.4.1.122.14.3.4.10.1.4
This attributes indicates the reason for the latest inactive A-bit status received from the ATM VCC. The value is notApplicable when the aBitStatusFromNetwork is active. The value is remoteUserSignaled if the remote FRF.5 End Point originating the A-Bit status has detected that the virtual circuit is down at the remote network through the LMI protocol. The remote FRF.5 End Point must be running network site LMI protocol for this A-Bit status reason to be sent. The value is localLmiError if the LMI protocol is down at this Ep. The value is localLinkDown if the physical interface is disabled at this Ep. The value is missingFromLmiReport if the remote FRF.5 End Point did not provide a reason along with the inactive A-Bit status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), remoteUserSignalled(1), localLmiError(2), localLinkDown(4), missingFromLmiReport(7)  

mcsMgrFrf5EpGEpDlciAccessConnectionComponent 1.3.6.1.4.1.562.2.4.1.122.14.3.4.10.1.5
This attribute identifies the FrAtm Dlci to which this Dlci component is bound.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AsciiString Size(0..23)  

mcsMgrFrf5EpGEpAtmCon 1.3.6.1.4.1.562.2.4.1.122.14.3.5
OBJECT IDENTIFIER    

mcsMgrFrf5EpGEpAtmConRowStatusTable 1.3.6.1.4.1.562.2.4.1.122.14.3.5.1
This entry controls the addition and deletion of mcsMgrFrf5EpGEpAtmCon components.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    McsMgrFrf5EpGEpAtmConRowStatusEntry

mcsMgrFrf5EpGEpAtmConRowStatusEntry 1.3.6.1.4.1.562.2.4.1.122.14.3.5.1.1
A single entry in the table represents a single mcsMgrFrf5EpGEpAtmCon component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  McsMgrFrf5EpGEpAtmConRowStatusEntry  

mcsMgrFrf5EpGEpAtmConRowStatus 1.3.6.1.4.1.562.2.4.1.122.14.3.5.1.1.1
This variable is used as the basis for SNMP naming of mcsMgrFrf5EpGEpAtmCon components. These components cannot be added nor deleted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RowStatus  

mcsMgrFrf5EpGEpAtmConComponentName 1.3.6.1.4.1.562.2.4.1.122.14.3.5.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

mcsMgrFrf5EpGEpAtmConStorageType 1.3.6.1.4.1.562.2.4.1.122.14.3.5.1.1.4
This variable represents the storage type value for the mcsMgrFrf5EpGEpAtmCon tables.
Status: mandatory Access: read-only
OBJECT-TYPE    
  StorageType  

mcsMgrFrf5EpGEpAtmConIndex 1.3.6.1.4.1.562.2.4.1.122.14.3.5.1.1.10
This variable represents the index for the mcsMgrFrf5EpGEpAtmCon tables.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NonReplicated  

mcsMgrFrf5EpGEpAtmConOperTable 1.3.6.1.4.1.562.2.4.1.122.14.3.5.10
This attribute group contains the operational attributes for the NapAtmConnection component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    McsMgrFrf5EpGEpAtmConOperEntry

mcsMgrFrf5EpGEpAtmConOperEntry 1.3.6.1.4.1.562.2.4.1.122.14.3.5.10.1
An entry in the mcsMgrFrf5EpGEpAtmConOperTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  McsMgrFrf5EpGEpAtmConOperEntry  

mcsMgrFrf5EpGEpAtmConNextHop 1.3.6.1.4.1.562.2.4.1.122.14.3.5.10.1.1
This attribute shows the component name of the AtmIf Vcc Ep or AtmCon component to which this switched connection is established.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RowPointer  

frf5EpGroup 1.3.6.1.4.1.562.2.4.2.121.1
OBJECT IDENTIFIER    

frf5EpGroupBD 1.3.6.1.4.1.562.2.4.2.121.1.4
OBJECT IDENTIFIER    

frf5EpGroupBD02 1.3.6.1.4.1.562.2.4.2.121.1.4.3
OBJECT IDENTIFIER    

frf5EpGroupBD02A 1.3.6.1.4.1.562.2.4.2.121.1.4.3.2
OBJECT IDENTIFIER    

frf5EpCapabilities 1.3.6.1.4.1.562.2.4.2.121.3
OBJECT IDENTIFIER    

frf5EpCapabilitiesBD 1.3.6.1.4.1.562.2.4.2.121.3.4
OBJECT IDENTIFIER    

frf5EpCapabilitiesBD02 1.3.6.1.4.1.562.2.4.2.121.3.4.3
OBJECT IDENTIFIER    

frf5EpCapabilitiesBD02A 1.3.6.1.4.1.562.2.4.2.121.3.4.3.2
OBJECT IDENTIFIER