NTWS-AP-TC

File: NTWS-AP-TC.mib (21943 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC NTWS-ROOT-MIB

Imported symbols

Unsigned32 Integer32 MODULE-IDENTITY
TEXTUAL-CONVENTION ntwsMibs

Defined Types

NtwsAccessType  
Describes the access type used by client or an AP. Value 'ap(1)' indicates access point that is directly attached to the switch. Value 'dap(2)' indicates distributed access point with attachment to the switch through the intermediate network. Value 'wired(3)' indicates a client that is directly attached to the switch (no access point is involved).
TEXTUAL-CONVENTION    
  INTEGER ap(1), dap(2), wired(3)  

NtwsApAttachType  
Type of AP attachment to AC.
TEXTUAL-CONVENTION    
  INTEGER directAttach(1), networkAttach(2)  

NtwsApPortOrDapNum  
AP Port, for directly attached APs, otherwise DAP Number (arbitrary number assigned when configuring the DAP on the AC). A zero value means unknown. Obsoleted by NtwsApNum. (In 6.0, direct- and network-attached APs were unified.)
TEXTUAL-CONVENTION    
  Unsigned32 0..1000  

NtwsApNum  
AP Number: arbitrary number assigned when configuring the AP on the AC. It is unique (on same AC), regardless of the type of AP attachment. A zero value means unknown.
TEXTUAL-CONVENTION    
  Unsigned32 0..9999  

NtwsApState  
AP State, as seen by the AC.
TEXTUAL-CONVENTION    
  INTEGER cleared(1), init(2), bootStarted(3), imageDownloaded(4), connectFailed(5), configuring(6), configured(7)  

NtwsApTransition  
AP state Transition, as seen by the AC.
TEXTUAL-CONVENTION    
  INTEGER clear(1), timeout(2), reset(3), bootSuccess(4), startConfiguring(5), connectFail(6)  

NtwsApFailDetail  
Detailed failure codes for some of the transitions specified in 'NtwsApTransition'. - 'normalTransition' (91) means the corresponding transition is not a failure; could be caused by an explicit request (for example, AP was cleared) or it is a transition towards operational state. - 'failUnknown' (99) means there are no details available; the transition may be normal or undesirable/unexpected.
TEXTUAL-CONVENTION    
  INTEGER secureHandshakeFailure(2), fingerprintRequired(3), fingerprintMismatch(4), portLinkUp(11), portLinkDown(12), normalTransition(91), failUnknown(99)  

NtwsApConnectSecurityType  
Security level of the connection between AP and AC: secure(1) - fingerprint matching; insecure(2) - fingerprint not configured, or optional and not matching; auto(3) - Auto-DAP is intrinsically insecure: could not check fingerprint since no specific DAP is configured.
TEXTUAL-CONVENTION    
  INTEGER secure(1), insecure(2), auto(3)  

NtwsApServiceAvailability  
Level of wireless service availability.
TEXTUAL-CONVENTION    
  INTEGER fullService(1), noService(2), degradedService(3)  

NtwsApBias  
Bias of AP attachment to this AC. Setting an APs bias on an AC switch to high causes the switch to be preferred over switches with low bias, for booting and managing the AP. Bias applies only to AC switches that are indirectly attached to the AP through an intermediate Layer 2 or Layer 3 network. An AP always attempts to boot on AP port 1 first, and if an AC switch is directly attached on AP port 1, the AP boots from it regardless of the bias settings.
TEXTUAL-CONVENTION    
  INTEGER high(1), low(2), sticky(3)  

NtwsApSerialNum  
The value is a zero length string if unknown or unavailable. Otherwise the value is a serial number, which consists of printable ASCII characters between 0x21 (!), and 0x7d (}) with no leading, embedded, or trailing space.
TEXTUAL-CONVENTION    
  OCTET STRING Size(0..32)  

NtwsApFingerprint  
Represents a RSA key fingerprint (binary value), which is the MD5 hash of the public key of the RSA key pair. Or a zero length string if not known or unavailable.
TEXTUAL-CONVENTION    
  OCTET STRING Size(0|16)  

NtwsRadioNum  
Enumeration for multi-radio APs.
TEXTUAL-CONVENTION    
  INTEGER radio-1(1), radio-2(2), not-applicable(3)  

NtwsApRadioIndex  
A unique value, greater than zero, for each Radio on the AP. Intended to replace NtwsRadioNum.
TEXTUAL-CONVENTION    
  Unsigned32 1..4294967295  

NtwsApRadioIndexOrZero  
This textual convention is an extension of the NtwsApRadioIndex convention. The latter defines a greater than zero value used to identify each Radio on the AP. This extension permits the additional value of zero. A zero value means 'none', 'unknown radio' or 'not applicable'. Each object using this textual convention should document the meaning of Radio Index zero.
TEXTUAL-CONVENTION    
  Unsigned32 0 | 1..4294967295  

NtwsPowerLevel  
The current level of transmit power expressed in dbm.
TEXTUAL-CONVENTION    
  Unsigned32  

NtwsRadioPowerChangeType  
Enumerations for why the power level was changed, which occurs due to auto-tune operation.
TEXTUAL-CONVENTION    
  INTEGER dup-pkts-threshold-exceed(1), retransmit-threshold-exceed(2), clients-optimal-performance-reached(3), def-power-threshold-exceed(4)  

NtwsChannelChangeType  
Enumerations for why the channel was changed, which occurs due to auto-tune operation
TEXTUAL-CONVENTION    
  INTEGER util-index(1), rexmit-pkt-offset(2), noise-offset(3), noise(4), utilization(5), phy-error-offset(6), crc-errors-offset(7), radar-detected(8)  

NtwsChannelNum  
Channel Number
TEXTUAL-CONVENTION    
  Unsigned32 1..1024  

NtwsRadioEnable  
Radio mode (administratively enabled or disabled). Obsoleted by NtwsRadioMode.
TEXTUAL-CONVENTION    
  INTEGER enabled(1), disabled(2)  

NtwsRadioMode  
Configured mode of an AP radio. There are three administratively controlled values: - enabled: radio may provide service to clients; - sentry: radio will not provide service, but can be used for RF scanning and can run countermeasures; - disabled: radio will not emit at all (thus cannot run countermeasures), can only be used for RF scanning. Obsoletes NtwsRadioEnable.
TEXTUAL-CONVENTION    
  INTEGER enabled(1), disabled(2), sentry(3)  

NtwsRadioConfigState  
Radio Configuration State, as seen by the AC.
TEXTUAL-CONVENTION    
  INTEGER configInit(1), configFail(2), configOk(3)  

NtwsRadioRate  
The possible transmission rates of an AP radio. Both a and b/g rates are covered; a specific radio will report the applicable transmission rates (either a or b/g). Here are the possible rates, in Mbps: - 802.11g radios: 54, 48, 36, 24, 18, 12, 11, 9, 6, 5.5, 2, or 1; - 802.11b radios: 11, 5.5, 2, or 1; - 802.11a radios: 54, 48, 36, 24, 18, 12, 9, or 6. The value in MIB is specified as the rate in Mbps times 10, in order to have only integer values, zero meaning unknown rate.
TEXTUAL-CONVENTION    
  Unsigned32 0 | 10..540  

NtwsRadioRateEx  
Radio Rates Extended (covering 11n MCS rates): The possible transmission rates of an AP radio. 11a, 11b/g, 11na and 11ng rates are included; a specific radio will report the applicable transmission rates (either a, b/g, na, ng). Here are the possible rates, in Mbps: - 802.11g radios: 54, 48, 36, 24, 18, 12, 11, 9, 6, 5.5, 2, or 1; - 802.11b radios: 11, 5.5, 2, or 1; - 802.11a radios: 54, 48, 36, 24, 18, 12, 9, or 6; - 802.11ng radios: MCS0-MCS15 and all 11g rates; - 802.11na radios: MCS0-MCS15 and all 11a rates.
TEXTUAL-CONVENTION    
  INTEGER rateUnknown(1), rate1(2), rate2(3), rate5-5(4), rate6(5), rate9(6), rate11(7), rate12(8), rate18(9), rate24(10), rate36(11), rate48(12), rate54(13), rateMCS0(20), rateMCS1(21), rateMCS2(22), rateMCS3(23), rateMCS4(24), rateMCS5(25), rateMCS6(26), rateMCS7(27), rateMCS8(28), rateMCS9(29), rateMCS10(30), rateMCS11(31), rateMCS12(32), rateMCS13(33), rateMCS14(34), rateMCS15(35)  

NtwsRadioType  
Enumeration to indicate the Radio Type, as seen by AC.
TEXTUAL-CONVENTION    
  INTEGER typeUnknown(1), typeA(2), typeB(3), typeG(4), typeNA(5), typeNG(6)  

NtwsRssi  
RSSI (Received Signal Strength Indicator) for last packet received, in decibels referred to 1 milliwatt (dBm). A higher value indicates a stronger signal.
TEXTUAL-CONVENTION    
  Integer32 -100..0  

NtwsApWasOperational  
Enumeration to indicate whether the AP was operational before a transition occurred. Normally used in notifications.
TEXTUAL-CONVENTION    
  INTEGER oper(1), nonOper(2)  

NtwsRadioChannelWidth  
Enumeration to indicate the administratively controlled Radio Channel Width.
TEXTUAL-CONVENTION    
  INTEGER channelWidth20MHz(1), channelWidth40MHz(2)  

NtwsRadioMimoState  
Enumeration to indicate the MIMO state of the Radio (Multiple Input Multiple Output), as seen by the AC. This depends on radio type and power supplied to the radio. mimo1x1: radio uses one transmit chain and one receive chain; mimo2x3: radio uses two transmit chains and three receive chains; mimo3x3: radio uses three transmit chains and three receive chains.
TEXTUAL-CONVENTION    
  INTEGER mimoOther(1), mimo1x1(2), mimo2x3(3), mimo3x3(4)  

NtwsApPowerMode  
Enumerations of the modes in which power is supplied by the AP to its components (mainly radios). There are two administratively controlled values: - auto: the power is managed automatically by sensing the power level on the AP; - high: all radios operate at the maximum power available.
TEXTUAL-CONVENTION    
  INTEGER auto(1), high(2)  

NtwsApLedMode  
Enumeration to indicate the administratively controlled LED mode for an AP.
TEXTUAL-CONVENTION    
  INTEGER auto(1), static(2), off(3)  

NtwsRadioAntennaLocation  
Enumeration to indicate the administratively controlled Radio Antenna Location.
TEXTUAL-CONVENTION    
  INTEGER indoors(1), outdoors(2)  

NtwsCryptoType  
Enumeration of Crypto Types: - clear: Cleartext (unencrypted communication); - wep: Wired Equivalent Privacy; - wep40: WEP with 40-bit keys; - wep104: WEP with 104-bit keys; - tkip: Temporal Key Integrity Protocol; - aesCcmp: Advanced Encryption Standard, Counter mode with CBC MAC Protocol.
TEXTUAL-CONVENTION    
  INTEGER other(1), clear(2), wep(3), wep40(4), wep104(5), tkip(6), aesCcmp(7)  

Defined Values

ntwsApTc 1.3.6.1.4.1.45.6.1.4.3
Textual Conventions used by Nortel Networks wireless switches. AP = Access Point; AC = Access Controller (wireless switch), the device that runs a SNMP Agent using these TCs. Copyright 2009 Nortel Networks. All rights reserved. This Nortel Networks SNMP Management Information Base Specification (Specification) embodies Nortel Networks' confidential and proprietary intellectual property. This Specification is supplied 'AS IS' and Nortel Networks makes no warranty, either express or implied, as to the use, operation, condition, or performance of the Specification.
MODULE-IDENTITY