NTNTECH-CHASSIS-CONFIGURATION-MIB

File: NTNTECH-CHASSIS-CONFIGURATION-MIB.mib (32637 bytes)

Imported modules

NTNTECH-ROOT-MIB SNMPv2-SMI SNMPv2-TC

Imported symbols

ntntechChassis NtnDefaultGateway NtnSubnetMask
NtnTimeTicks NtnDisplayString OBJECT-TYPE
MODULE-IDENTITY IpAddress TEXTUAL-CONVENTION

Defined Types

MumCfgEntry  
SEQUENCE    
  mumCfgIndex INTEGER
  mumCfgIpAddress IpAddress
  mumCfgSubnetMask IpAddress
  mumCfgDefaultGateway IpAddress
  mumCfgInbandMgmt INTEGER
  mumCfgInbandMGMTVlanID INTEGER
  mumCfgInterConnection INTEGER
  mumCfgCommitChange INTEGER

UimCfgEthEntry  
SEQUENCE    
  uimCfgEthMumIndex INTEGER
  uimCfgEthIndex INTEGER
  uimCfgEthRxTxRate INTEGER
  uimCfgEthDuplex INTEGER

UimCfgT1Entry  
SEQUENCE    
  uimCfgT1MumIndex INTEGER
  uimCfgT1Index INTEGER
  uimCfgT1Frame INTEGER
  uimCfgT1LineCode INTEGER
  uimCfgT1LineBuildout INTEGER

UimCfgE1Entry  
SEQUENCE    
  uimCfgE1MumIndex INTEGER
  uimCfgE1Index INTEGER
  uimCfgE1Frame INTEGER
  uimCfgE1LineCode INTEGER

SnmpCfgNoticeIpEntry  
SEQUENCE    
  snmpCfgNoticeIndex INTEGER
  snmpCfgNoticeIpAddress IpAddress

AdvCfgEntry  
SEQUENCE    
  advCfgMumIndex INTEGER
  advCfgTFTPState INTEGER
  advCfgTelnetState INTEGER
  advCfgMgmtFltrIpStart IpAddress
  advCfgMgmtFltrIpEnd IpAddress
  advCfgMgmtSessionTimeout NtnTimeTicks

MgmtPortCfgEntry  
SEQUENCE    
  mgmtPortCfgMumIndex INTEGER
  mgmtPortCfgRxTxRate INTEGER
  mgmtPortCfgDuplex INTEGER
  mgmtPortCfgType INTEGER

Defined Values

ntntechChassisConfigurationMIB 1.3.6.1.4.1.8059.1.1.1
This mib module defines an SNMP API to manage the Paradyne Corporation's DSLAM chassis parameters. These parameter settings are specifically associated with the the MUM200-2 and MUM2000-2 modules and the Mini and Micro DSLAMs. The interface types are described below, AMD8000-12 12-Port ADSL Mini DSLAMs With Full Rate and G.lite Operational Modes SMD2000-12, SMD2000Q-12, SMD2000G-12 12-Port SDSL Mini DSLAMs: AC and DC Versions with Cap, 2B1Q and G.SHDSL line encoding SuD2011_12T, SuD2011_12E, SuD2003_12T, SuD2003_12E 12-Port SDSL Micro DSLAMs: Cap, 2B1Q and G.SHDSL line encoding SuD2011_6T, SuD2011_6E, SuD2002_6T, SuD2002_6E 6-Port SDSL Micro DSLAMs: Cap, 2B1Q and G.SHDSL line encoding MUM200-2, MUM2000-2 Multiplexer Uplink Module with Dual Uplink Interface Module Capacity UIM-10/100 Uplink Interface Module UIM-DS3 DS3 Uplink Interface Module UIM-E1 E1 Uplink Interface Module UIM-E3 E3 Uplink Interface Module UIM-T1 T1 Uplink Interface Module
MODULE-IDENTITY    

chsCfgMIBObjects 1.3.6.1.4.1.8059.1.1.1.1
OBJECT IDENTIFIER    

chsCfgParameterConfiguration 1.3.6.1.4.1.8059.1.1.1.1.1
OBJECT IDENTIFIER    

prmCfgMultiplexerUplinkModule 1.3.6.1.4.1.8059.1.1.1.1.1.1
OBJECT IDENTIFIER    

mumCfgNotes 1.3.6.1.4.1.8059.1.1.1.1.1.1.1
The chassis system 'Notes' field is to be used as a scratchpad (i.e. chassis id or name) by the administrator. The default value is blank. The length of string must not exceed 128 alpha-numeric characters.
Status: current Access: read-write
OBJECT-TYPE    
  NtnDisplayString  

mumCfgTable 1.3.6.1.4.1.8059.1.1.1.1.1.1.2
A list of MUM200-2/2000-2 module or Mini/Micro DSLAM entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MumCfgEntry

mumCfgEntry 1.3.6.1.4.1.8059.1.1.1.1.1.1.2.1
An entry containing management information applicable to a MUM200-2/MUM2000-2 module or Mini/Micro DSLAM.
Status: current Access: not-accessible
OBJECT-TYPE    
  MumCfgEntry  

mumCfgIndex 1.3.6.1.4.1.8059.1.1.1.1.1.1.2.1.1
Translates to the physical slot number that a MUM200-2/2000-2 module exists within a chassis. The Mini/Micro DSLAMs' physical location is set to 1 by default. See below, chassis type physical location(s) translation ------------ -------------------------------- IPD12000 MUM in slots 13,14 = mumCfgIndex 1,2 respecitively IPD4000 MUM in slot 5 = mumCfgIndex 1 Mini DSLAM NA = mumCfgIndex 1 Micro DSLAM NA = mumCfgIndex 1
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2  

mumCfgIpAddress 1.3.6.1.4.1.8059.1.1.1.1.1.1.2.1.2
IP Address assigned to a MUM200-2/2000-2 module or Mini/Micro DSLAM. This parameter is initially set to a default value, i.e 192.168.254.252 for a MUM200-2/2000-2 module located in slot 13 of an IPD12000, slot 5 of an IPD4000 DSLAM and a Mini/Micro DSLAM. The default value of 192.168.254.253 will be for a MUM200-2/2000-2 module located in slot 14 of an IPD12000 (duplicate IP addresses are not allowed). These default values can be modified by the user.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

mumCfgSubnetMask 1.3.6.1.4.1.8059.1.1.1.1.1.1.2.1.3
The Subnet Mask assigned to a MUM200-2/2000-2 module or Mini/Micro DSLAM. This parameter is assiged by the user, the default value is 255.255.255.0.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

mumCfgDefaultGateway 1.3.6.1.4.1.8059.1.1.1.1.1.1.2.1.4
The Default Gateway assigned to a MUM200-2/2000-2 module or Mini/Micro DSLAM. This value is assiged by the user, the default value is 0.0.0.0.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

mumCfgInbandMgmt 1.3.6.1.4.1.8059.1.1.1.1.1.1.2.1.5
Inband management feature, when enabled [ON(1)], allows access to the DSLAM via the network against an assigned IP address, subnet mask, and default gateway.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

mumCfgInbandMGMTVlanID 1.3.6.1.4.1.8059.1.1.1.1.1.1.2.1.6
The IP DSLAM supports 802.1Q Virtual LANs (VLANs). This parameter configuration applies to the inband management traffic only. It does not apply to out of band traffic received from the MGMT port. Note: for the case where the chassis type is an IPD12000 loaded with two MUMs, the setting of this parameter will affect both.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4085  

mumCfgInterConnection 1.3.6.1.4.1.8059.1.1.1.1.1.1.2.1.7
IPD12000 or IPD4000 DSLAM interconnect configuration provides the system manager the ability to daisy-chain one IP DSLAM to another so that a single router may be used for all DSLAMs in the chain.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER neither(1), uplink1(2), uplink2(3), uplink3(4), uplink4(5), mgmt(6)  

mumCfgCommitChange 1.3.6.1.4.1.8059.1.1.1.1.1.1.2.1.8
Set to enabled(1) in order to commit the latest changes to the IP address, subnetmask, default gateway chassis parameters. This is only applicable to the SNE2040G-P and the SNE2040G-S.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mumCfgUplinkInterfaceModule 1.3.6.1.4.1.8059.1.1.1.1.1.1.3
OBJECT IDENTIFIER    

uimCfgEthTable 1.3.6.1.4.1.8059.1.1.1.1.1.1.3.1
A list of ethernet Uplink Interface Module (UIM) entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UimCfgEthEntry

uimCfgEthEntry 1.3.6.1.4.1.8059.1.1.1.1.1.1.3.1.1
An entry containing information applicable to an ethernet Uplink Interface Module (UIM).
Status: current Access: not-accessible
OBJECT-TYPE    
  UimCfgEthEntry  

uimCfgEthMumIndex 1.3.6.1.4.1.8059.1.1.1.1.1.1.3.1.1.1
Translates to the physical slot number that a MUM200-2/2000-2 module exists within a chassis. The Mini/Micro DSLAMs' physical location is set to 1 by default. See below, chassis type physical location(s) translation ------------ -------------------------------- IPD12000 MUM in slots 13,14 = uimCfgEthMumIndex 1,2 respecitively IPD4000 MUM in slot 5 = uimCfgEthMumIndex 1 Mini DSLAM NA = uimCfgEthMumIndex 1 Micro DSLAM NA = uimCfgEthMumIndex 1 Note: when configuring an ethernet UIM, the user must enter the index of the MUM, see above table, that corresponds with the IP address of the remote SNMP agent.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2  

uimCfgEthIndex 1.3.6.1.4.1.8059.1.1.1.1.1.1.3.1.1.2
The physical slot used to access the UIM in the MUM200-2/2000-2 module or Mini/Micro DSLAM.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..4  

uimCfgEthRxTxRate 1.3.6.1.4.1.8059.1.1.1.1.1.1.3.1.1.3
The RxTx rate for an ethernet UIM.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER uimEthAutoNegotiate(0), uimEth10(1), uimEth100(2), uimEthGig(3)  

uimCfgEthDuplex 1.3.6.1.4.1.8059.1.1.1.1.1.1.3.1.1.4
The current duplex setting for an ethernet UIM.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER uimEthAutoNegotiate(0), uimEthHalf(1), uimEthFull(2)  

uimCfgT1Table 1.3.6.1.4.1.8059.1.1.1.1.1.1.3.2
A list of T1 Uplink Interface Module (UIM) entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UimCfgT1Entry

uimCfgT1Entry 1.3.6.1.4.1.8059.1.1.1.1.1.1.3.2.1
An entry containing information applicable to a T1 Uplink Interface Module (UIM).
Status: current Access: not-accessible
OBJECT-TYPE    
  UimCfgT1Entry  

uimCfgT1MumIndex 1.3.6.1.4.1.8059.1.1.1.1.1.1.3.2.1.1
Translates to the physical slot number that a MUM200-2/2000-2 module exists within a chassis. The Mini/Micro DSLAMs' physical location is set to 1 by default. See below, chassis type physical location(s) translation ------------ -------------------------------- IPD12000 MUM in slots 13,14 = uimCfgT1MumIndex 1,2 respecitively IPD4000 MUM in slot 5 = uimCfgT1MumIndex 1 Mini DSLAM NA = uimCfgT1MumIndex 1 Micro DSLAM NA = uimCfgT1MumIndex 1 Note: when configuring a T1 UIM, the user must enter the index of the MUM, see above table, that corresponds with the IP address of the remote SNMP agent.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2  

uimCfgT1Index 1.3.6.1.4.1.8059.1.1.1.1.1.1.3.2.1.2
The physical slot used to access the UIM in the MUM200-2/2000-2 module or Mini/Micro DSLAM.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..4  

uimCfgT1Frame 1.3.6.1.4.1.8059.1.1.1.1.1.1.3.2.1.3
The frame type parameter for a T1 UIM.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER uimT1ESF(1), uimT1SFD4(2)  

uimCfgT1LineCode 1.3.6.1.4.1.8059.1.1.1.1.1.1.3.2.1.4
The line code parameter for a T1 UIM.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER uimT1B8ZS(1), uimT1AMI(2)  

uimCfgT1LineBuildout 1.3.6.1.4.1.8059.1.1.1.1.1.1.3.2.1.5
The line buildout parameter for a T1 UIM.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER uimT10db(1), uimT1N7p5db(2), uimT1N15db(3), uimT1N22p5db(4)  

uimCfgE1Table 1.3.6.1.4.1.8059.1.1.1.1.1.1.3.3
A list of E1 Uplink Interface Module (UIM) entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UimCfgE1Entry

uimCfgE1Entry 1.3.6.1.4.1.8059.1.1.1.1.1.1.3.3.1
An entry containing information applicable to an E1 Uplink Interface Module (UIM).
Status: current Access: not-accessible
OBJECT-TYPE    
  UimCfgE1Entry  

uimCfgE1MumIndex 1.3.6.1.4.1.8059.1.1.1.1.1.1.3.3.1.1
Translates to the physical slot number that a MUM200-2/2000-2 module exists within a chassis. The Mini/Micro DSLAMs' physical location is set to 1 by default. See below, chassis type physical location(s) translation ------------ -------------------------------- IPD12000 MUM in slots 13,14 = uimCfgE1MumIndex 1,2 respecitively IPD4000 MUM in slot 5 = uimCfgE1MumIndex 1 Mini DSLAM NA = uimCfgE1MumIndex 1 Micro DSLAM NA = uimCfgE1MumIndex 1 Note: when configuring an E1 UIM, the user must enter the index of the MUM, see above table, that corresponds with the IP address of the remote SNMP agent.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2  

uimCfgE1Index 1.3.6.1.4.1.8059.1.1.1.1.1.1.3.3.1.2
The physical slot used to access the UIM in the MUM200-2/2000-2 module or Mini/Micro DSLAM.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..4  

uimCfgE1Frame 1.3.6.1.4.1.8059.1.1.1.1.1.1.3.3.1.3
The frame type parameter for an E1 UIM.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER uimE1CRC(1), uimE1NoCRC(2)  

uimCfgE1LineCode 1.3.6.1.4.1.8059.1.1.1.1.1.1.3.3.1.4
The line code parameter for an E1 UIM.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER uimE1HDB3(1), uimE1AMI(2)  

mumSNMPConfiguration 1.3.6.1.4.1.8059.1.1.1.1.1.1.4
OBJECT IDENTIFIER    

snmpCfgNoticeIpTable 1.3.6.1.4.1.8059.1.1.1.1.1.1.4.1
A list of SNMP trap notification Ip Addresses.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SnmpCfgNoticeIpEntry

snmpCfgNoticeIpEntry 1.3.6.1.4.1.8059.1.1.1.1.1.1.4.1.1
An entry containing SNMP information applicable to a MUM200-2/MUM2000-2 module or Mini/Micro DSLAM.
Status: current Access: not-accessible
OBJECT-TYPE    
  SnmpCfgNoticeIpEntry  

snmpCfgNoticeIndex 1.3.6.1.4.1.8059.1.1.1.1.1.1.4.1.1.1
An integer value that points to one of four trap notification IP addresses.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..4  

snmpCfgNoticeIpAddress 1.3.6.1.4.1.8059.1.1.1.1.1.1.4.1.1.2
IP Address of the location or computer to which you would like trap notifications sent. The default value is 0.0.0.0 and it can be modified by the user.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

snmpCfgAuthenticationTrapState 1.3.6.1.4.1.8059.1.1.1.1.1.1.4.2
Indicates whether Authentication traps should be generated. By default, this object should have the value enabled(1).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

snmpCfgEnvironmentTrapState 1.3.6.1.4.1.8059.1.1.1.1.1.1.4.3
Indicates whether the fan and temperature traps should be generated. By default, this object should have the value enabled(1).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

snmpCfgColdstartTrapState 1.3.6.1.4.1.8059.1.1.1.1.1.1.4.4
Indicates whether Cold Start traps should be generated. By default, this object should have the value disabled(2).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

snmpCfgModulePortTrapState 1.3.6.1.4.1.8059.1.1.1.1.1.1.4.5
Indicates whether the module present/removed and link up/down traps should be generated. By default, this object should have the value disabled(2).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

snmpCfgCommunity 1.3.6.1.4.1.8059.1.1.1.1.1.1.4.6
OBJECT IDENTIFIER    

comReadWriteAccess 1.3.6.1.4.1.8059.1.1.1.1.1.1.4.6.1
The community string that will allow the user read/write access to the agent. In otherwords, the user will be allowed to view and set parameter attributes. Note: since this is a hidden attribute, for security purposes, when performing a get on this OID the string that is returned will be represented by asterisk(s).
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..15)  

comReadOnlyAccess 1.3.6.1.4.1.8059.1.1.1.1.1.1.4.6.2
The community string that will allow the user read access to the agent. In otherwords, the user will be allowed to view parameter attributes. Note: since this is a hidden attribute, for security purposes, when performing a get on this OID the string that is returned will be represented by asterisk(s).
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..15)  

mumCfgUniques 1.3.6.1.4.1.8059.1.1.1.1.1.1.5
OBJECT IDENTIFIER    

unqEmbHttpWebsrvrState 1.3.6.1.4.1.8059.1.1.1.1.1.1.5.1
This configuration parameter allows the user the ability to disable, or enable, the embedded webserver. By default, this object should have the value enabled(1).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

mumCfgAdvanced 1.3.6.1.4.1.8059.1.1.1.1.1.1.6
OBJECT IDENTIFIER    

advCfgTable 1.3.6.1.4.1.8059.1.1.1.1.1.1.6.1
A list of the Advanced Configuration entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdvCfgEntry

advCfgEntry 1.3.6.1.4.1.8059.1.1.1.1.1.1.6.1.1
An entry containing information applicable to an Advanced Configuration parameter.
Status: current Access: not-accessible
OBJECT-TYPE    
  AdvCfgEntry  

advCfgMumIndex 1.3.6.1.4.1.8059.1.1.1.1.1.1.6.1.1.1
Translates to the physical slot number that a MUM200-2/2000-2 module exists within a chassis. The Mini/Micro DSLAMs' physical location is set to 1 by default. See below, chassis type physical location(s) translation ------------ -------------------------------- IPD12000 MUM in slots 13,14 = uimCfgE1MumIndex 1,2 respecitively IPD4000 MUM in slot 5 = uimCfgE1MumIndex 1 Mini DSLAM NA = uimCfgE1MumIndex 1 Micro DSLAM NA = uimCfgE1MumIndex 1 Note: when configuring an Advanced Configuration parameter, the user must enter the index of the MUM, see above table, that corresponds with the IP address of the remote SNMP agent.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2  

advCfgTFTPState 1.3.6.1.4.1.8059.1.1.1.1.1.1.6.1.1.2
This configuration parameter allows the user the ability to disable, or enable, the TFTP server. By default, this object should have the value enabled(1).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

advCfgTelnetState 1.3.6.1.4.1.8059.1.1.1.1.1.1.6.1.1.3
This configuration parameter allows the user the ability to disable, or enable, telnet. By default, this object should have the value enabled(1).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

advCfgMgmtFltrIpStart 1.3.6.1.4.1.8059.1.1.1.1.1.1.6.1.1.4
The start value for the management IP filter range. This parameter is initially set to a default filter range of 0.0.0.0 - 255.255.255.255. Connection to the management system will be allowed only if the user's Ip address value falls within the defined mumCfgMgmtIpStart and mumCfgMgmtIpEnd range.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

advCfgMgmtFltrIpEnd 1.3.6.1.4.1.8059.1.1.1.1.1.1.6.1.1.5
The end value for the management IP filter range. This parameter is initially set to a default filter range of 0.0.0.0 - 255.255.255.255. Connection to the management system will be allowed only if the user's Ip address value falls within the defined mumCfgMgmtIpStart and mumCfgMgmtIpEnd range.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

advCfgMgmtSessionTimeout 1.3.6.1.4.1.8059.1.1.1.1.1.1.6.1.1.6
This value defines the length of a password session in seconds. If the session has been idle for a time greater than this value, the browser will be challenged again, even if it has provided authentication credentials with the request.
Status: current Access: read-write
OBJECT-TYPE    
  NtnTimeTicks  

mumCfgManagementPort 1.3.6.1.4.1.8059.1.1.1.1.1.1.7
OBJECT IDENTIFIER    

mgmtPortCfgTable 1.3.6.1.4.1.8059.1.1.1.1.1.1.7.1
A list of the hardware platform management port entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MgmtPortCfgEntry

mgmtPortCfgEntry 1.3.6.1.4.1.8059.1.1.1.1.1.1.7.1.1
An entry containing information applicable to the managment (ethernet type) port.
Status: current Access: not-accessible
OBJECT-TYPE    
  MgmtPortCfgEntry  

mgmtPortCfgMumIndex 1.3.6.1.4.1.8059.1.1.1.1.1.1.7.1.1.1
Translates to the physical slot number that a MUM200-2/2000-2 module exists within a chassis. The Mini/Micro DSLAMs' physical location is set to 1 by default. See below, chassis type physical location(s) translation ------------ -------------------------------- IPD12000 MUM in slots 13,14 = uimCfgEthMumIndex 1,2 respecitively IPD4000 MUM in slot 5 = uimCfgEthMumIndex 1 Mini DSLAM NA = uimCfgEthMumIndex 1 Micro DSLAM NA = uimCfgEthMumIndex 1 Note: when configuring a management port, the user must enter the index of the MUM, see above table, that corresponds with the IP address of the remote SNMP agent.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2  

mgmtPortCfgRxTxRate 1.3.6.1.4.1.8059.1.1.1.1.1.1.7.1.1.2
Set the RxTx rate for an ethernet management port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER uimEthAutoNegotiate(0), uimEth10(1), uimEth100(2), uimEthGig(3)  

mgmtPortCfgDuplex 1.3.6.1.4.1.8059.1.1.1.1.1.1.7.1.1.3
Set the duplex setting for an ethernet management port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER uimEthAutoNegotiate(0), uimEthHalf(1), uimEthFull(2)  

mgmtPortCfgType 1.3.6.1.4.1.8059.1.1.1.1.1.1.7.1.1.4
Set the management port type as follows. By setting this port to mgmt(1), it will operate as a non-bridge mode connection. Setting it to uplink(2), this port will operate like an uplink interface module, i.e. a bridge mode connection. Note: this applies to the AuD8000-12 micro DSLAM only.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER mgmt(1), uplink(2)