NHDP-MIB

File: NHDP-MIB.mib (90491 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
SNMP-FRAMEWORK-MIB INET-ADDRESS-MIB IF-MIB
FLOAT-TC-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
Counter32 Counter64 Integer32
Unsigned32 mib-2 TimeTicks
TEXTUAL-CONVENTION TruthValue TimeStamp
RowStatus MODULE-COMPLIANCE OBJECT-GROUP
NOTIFICATION-GROUP SnmpAdminString InetAddressType
InetAddress InetAddressPrefixLength InterfaceIndex
Float32TC

Defined Types

NeighborIfIndex  
An arbitrary, locally unique identifier associated with a virtual interface of a discovered NHDP neighbor. Due to the nature of NHDP, the local router may not know if two distinct addresses belong to the same interface of a neighbor or to two different interfaces. As the local router gains more knowledge of its neighbors, its local view may change, and this table will be updated to reflect the local router's current understanding, associating address sets to neighbor interfaces. The local router identifies a virtual neighbor interface through the receipt of address lists advertised through an NHDP HELLO message. All objects of type NeighborIfIndex are assigned by the agent out of a common number space. The value for each discovered virtual neighbor interface may not remain constant from one re-initialization of the entity's network management agent to the next re-initialization. If the local router gains information associating two virtual interfaces on a neighbor as a common interface, then the agent MUST aggregate the two address sets to a single index chosen from the set of aggregated indexes, and it MUST update all tables in this MIB module that are indexed by indexes of type NeighborIfIndex. It MAY then reuse freed index values following the next agent restart. The specific value is meaningful only within a given SNMP entity.
TEXTUAL-CONVENTION    
  Unsigned32 1..2147483647  

NeighborRouterIndex  
An arbitrary, locally unique identifier associated with a virtual discovered neighbor (one or two hop). Due to the nature of NHDP, the local router may identify multiple virtual neighbors that, in fact, are one and the same. Neighbors that are two hops away with more than one advertised address will exhibit this behavior. As the local router's knowledge of its neighbors' topology increases, the local router will be able to associate multiple virtual neighbor indexes into a single virtual neighbor index chosen from the set of aggregated indexes; it MUST update all tables in this MIB module indexed by these indexes, and it MAY reuse the freed indexes following the next agent re-initialization. All objects of type NeighborRouterIndex are assigned by the agent out of a common number space. The NeighborRouterIndex defines a discovered NHDP peer virtual neighbor of the local router. The value for each discovered virtual neighbor index MUST remain constant at least from one re-initialization of the entity's network management agent to the next re-initialization, except if an application is deleted and re-created. The specific value is meaningful only within a given SNMP entity. A NeighborRouterIndex value MUST not be reused until the next agent restart.
TEXTUAL-CONVENTION    
  Unsigned32 1..2147483647  

NhdpInterfaceEntry  
SEQUENCE    
  nhdpIfIndex InterfaceIndex
  nhdpIfName SnmpAdminString
  nhdpIfStatus TruthValue
  nhdpHelloInterval Unsigned32
  nhdpHelloMinInterval Unsigned32
  nhdpRefreshInterval Unsigned32
  nhdpLHoldTime Unsigned32
  nhdpHHoldTime Unsigned32
  nhdpHystAcceptQuality Float32TC
  nhdpHystRejectQuality Float32TC
  nhdpInitialQuality Float32TC
  nhdpInitialPending TruthValue
  nhdpHpMaxJitter Unsigned32
  nhdpHtMaxJitter Unsigned32
  nhdpIfRowStatus RowStatus

NhdpLibLocalIfSetEntry  
SEQUENCE    
  nhdpLibLocalIfSetIndex Integer32
  nhdpLibLocalIfSetIfIndex InterfaceIndex
  nhdpLibLocalIfSetIpAddrType InetAddressType
  nhdpLibLocalIfSetIpAddr InetAddress
  nhdpLibLocalIfSetIpAddrPrefixLen InetAddressPrefixLength
  nhdpLibLocalIfSetRowStatus RowStatus

NhdpLibRemovedIfAddrSetEntry  
SEQUENCE    
  nhdpLibRemovedIfAddrSetIndex Integer32
  nhdpLibRemovedIfAddrSetIpAddrType InetAddressType
  nhdpLibRemovedIfAddrSetIpAddr InetAddress
  nhdpLibRemovedIfAddrSetIpAddrPrefixLen InetAddressPrefixLength
  nhdpLibRemovedIfAddrSetIfIndex InterfaceIndex
  nhdpLibRemovedIfAddrSetIRTime TimeStamp

NhdpInterfaceStateEntry  
SEQUENCE    
  nhdpIfStateUpTime TimeStamp

NhdpDiscIfSetEntry  
SEQUENCE    
  nhdpDiscIfSetIndex Integer32
  nhdpDiscIfIndex NeighborIfIndex
  nhdpDiscRouterIndex NeighborRouterIndex
  nhdpDiscIfSetIpAddrType InetAddressType
  nhdpDiscIfSetIpAddr InetAddress
  nhdpDiscIfSetIpAddrPrefixLen InetAddressPrefixLength

NhdpIibLinkSetEntry  
SEQUENCE    
  nhdpIibLinkSetLHeardTime TimeStamp
  nhdpIibLinkSetLSymTime TimeStamp
  nhdpIibLinkSetLPending TruthValue
  nhdpIibLinkSetLLost TruthValue
  nhdpIibLinkSetLTime TimeStamp

NhdpIib2HopSetEntry  
SEQUENCE    
  nhdpIib2HopSetIpAddressType InetAddressType
  nhdpIib2HopSetIpAddress InetAddress
  nhdpIib2HopSetIpAddrPrefixLen InetAddressPrefixLength
  nhdpIib2HopSet1HopIfIndex NeighborIfIndex
  nhdpIib2HopSetN2Time TimeStamp

NhdpNibNeighborSetEntry  
SEQUENCE    
  nhdpNibNeighborSetNSymmetric TruthValue

NhdpNibLostNeighborSetEntry  
SEQUENCE    
  nhdpNibLostNeighborSetNLTime TimeStamp

NhdpInterfacePerfEntry  
SEQUENCE    
  nhdpIfHelloMessageXmits Counter32
  nhdpIfHelloMessageRecvd Counter32
  nhdpIfHelloMessageXmitAccumulatedSize Counter64
  nhdpIfHelloMessageRecvdAccumulatedSize Counter64
  nhdpIfHelloMessageTriggeredXmits Counter32
  nhdpIfHelloMessagePeriodicXmits Counter32
  nhdpIfHelloMessageXmitAccumulatedSymmetricNeighborCount Counter32
  nhdpIfHelloMessageXmitAccumulatedHeardNeighborCount Counter32
  nhdpIfHelloMessageXmitAccumulatedLostNeighborCount Counter32

NhdpDiscIfSetPerfEntry  
SEQUENCE    
  nhdpDiscIfRecvdPackets Counter32
  nhdpDiscIfExpectedPackets Counter32

NhdpDiscNeighborSetPerfEntry  
SEQUENCE    
  nhdpDiscNeighborNibNeighborSetChanges Counter32
  nhdpDiscNeighborNibNeighborSetUpTime TimeStamp
  nhdpDiscNeighborNibNeighborSetReachableLinkChanges Counter32

NhdpIib2HopSetPerfEntry  
SEQUENCE    
  nhdpIib2HopSetPerfChanges Counter32
  nhdpIib2HopSetPerfUpTime TimeStamp

Defined Values

nhdpMIB 1.3.6.1.2.1.213
This NHDP-MIB module is applicable to routers implementing the Neighborhood Discovery Protocol defined in RFC 6130. Copyright (c) 2012 IETF Trust and the persons identified as authors of the code. All rights reserved. Redistribution and use in source and binary forms, with or without modification, is permitted pursuant to, and subject to the license terms contained in, the Simplified BSD License set forth in Section 4.c of the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info). This version of this MIB module is part of RFC 6779; see the RFC itself for full legal notices.
MODULE-IDENTITY    

nhdpNotifications 1.3.6.1.2.1.213.0
OBJECT IDENTIFIER    

nhdpObjects 1.3.6.1.2.1.213.1
OBJECT IDENTIFIER    

nhdpConformance 1.3.6.1.2.1.213.2
OBJECT IDENTIFIER    

nhdpConfigurationObjGrp 1.3.6.1.2.1.213.1.1
OBJECT IDENTIFIER    

nhdpInterfaceTable 1.3.6.1.2.1.213.1.1.1
The nhdpInterfaceTable describes the configuration of the interfaces of this router that are intended to use MANET control protocols. As such, this table 'sparse augments' the ifTable specifically when NHDP is to be configured to operate over this interface. The interface is identified by the ifIndex from the interfaces group defined in the Interfaces Group MIB module. A conceptual row in this table exists if and only if either a manager has explicitly created the row or there is an interface on the managed device that supports and runs NHDP. The manager can create a row by setting rowStatus to 'createAndGo' or 'createAndWait'. Row objects having associated DEFVAL clauses are automatically defined by the agent with these values during row creation, unless the manager explicitly defines these object values during the row creation. If the corresponding entry with ifIndex value is deleted from the Interface Table, then the entry in this table is automatically deleted, NHDP is disabled on this interface, and all configuration and state information related to this interface is to be removed from memory.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NhdpInterfaceEntry

nhdpInterfaceEntry 1.3.6.1.2.1.213.1.1.1.1
The nhdpInterfaceEntry describes one NHDP local interface configuration as indexed by its ifIndex as defined in the Standard MIB II Interface Table (RFC 2863). The objects in this table are persistent, and when written, the device SHOULD save the change to non-volatile storage. For further information on the storage behavior for these objects, refer to the description for the nhdpIfRowStatus object.
Status: current Access: not-accessible
OBJECT-TYPE    
  NhdpInterfaceEntry  

nhdpIfIndex 1.3.6.1.2.1.213.1.1.1.1.1
This value MUST correspond to an ifIndex referring to a valid entry in the Interfaces Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

nhdpIfName 1.3.6.1.2.1.213.1.1.1.1.2
The textual name of the interface. The value of this object SHOULD be the name of the interface as assigned by the local device. This can be a text-name, such as 'le0' or a simple port number, such as '1', depending on the interface-naming syntax of the device. If there is no local name or this object is otherwise not applicable, then this object contains a zero-length string.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

nhdpIfStatus 1.3.6.1.2.1.213.1.1.1.1.3
nhdpIfStatus indicates whether this interface is currently running NHDP. A value of 'true(1)' indicates that NHDP is running on this interface. A value of 'false(2)' indicates that NHDP is not currently running on this interface. This corresponds to the I_manet parameter in the Local Interface Set of NHDP.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

nhdpHelloInterval 1.3.6.1.2.1.213.1.1.1.1.4
nhdpHelloInterval corresponds to HELLO_INTERVAL of NHDP and represents the maximum time between the transmission of two successive HELLO messages on this MANET interface. Guidance for setting this object may be found in Section 5 of the NHDP specification (RFC 6130), which indicates that: o nhdpHelloInterval > 0 o nhdpHelloInterval >= nhdpHelloMinInterval
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

nhdpHelloMinInterval 1.3.6.1.2.1.213.1.1.1.1.5
nhdpHelloMinInterval corresponds to HELLO_MIN_INTERVAL of NHDP and represents the minimum interval between transmission of two successive HELLO messages on this MANET interface. Guidance for setting this object may be found in Section 5 of the NHDP specification (RFC 6130), which indicates that: o nhdpHelloMinInterval <= nhdpHelloInterval
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

nhdpRefreshInterval 1.3.6.1.2.1.213.1.1.1.1.6
nhdpRefreshInterval corresponds to REFRESH_INTERVAL of NHDP and represents the maximum interval between advertisements of each 1-hop neighbor network address and its status. Each advertisement is in a HELLO message on this MANET interface. Guidance for setting this object may be found in Section 5 of the NHDP specification (RFC 6130), which indicates that: o nhdpRefreshInterval >= nhdpHelloInterval
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

nhdpLHoldTime 1.3.6.1.2.1.213.1.1.1.1.7
nhdpLHoldTime corresponds to L_HOLD_TIME of NHDP and represents the period of advertisement, on this MANET interface, of former 1-hop neighbor network addresses as lost in HELLO messages, allowing recipients of these HELLO messages to accelerate removal of this information from their Link Sets. Guidance for setting this object may be found in Section 5 of the NHDP specification (RFC 6130), which indicates that it should be assigned a value significantly greater than the refresh interval held by nhdpRefreshInterval.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

nhdpHHoldTime 1.3.6.1.2.1.213.1.1.1.1.8
nhdpHHoldTime corresponds to H_HOLD_TIME of NHDP and is used as the value in the VALIDITY_TIME Message TLV included in all HELLO messages on this MANET interface. It is then used by each router receiving such a HELLO message to indicate the validity of the information taken from that HELLO message and recorded in the receiving router's Information Bases. Guidance for setting this object may be found in Section 5 of the NHDP specification (RFC 6130), which indicates that it should be assigned a value significantly greater than the refresh interval held by nhdpRefreshInterval and must be representable as described in RFC 5497.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

nhdpHystAcceptQuality 1.3.6.1.2.1.213.1.1.1.1.9
nhdpHystAcceptQuality corresponds to HYST_ACCEPT of NHDP and represents the link quality threshold at or above which a link becomes usable, if it was not already so. Guidance for setting this object may be found in Section 5 of the NHDP specification (RFC 6130), which indicates that: o 0 <= nhdpHystRejectQuality <= nhdpHystAcceptQuality <= 1.0 The default value for this object is 1.0. According to RFC 6340: Since these textual conventions are defined in terms of the OCTET STRING type, the SMI's mechanisms for formally setting range constraints are not available. MIB designers using these textual conventions will need to use DESCRIPTION clauses to spell out any applicable range constraints beyond those implied by the underlying IEEE types. Therefore, this object does not have a DEFVAL clause.
Status: current Access: read-create
OBJECT-TYPE    
  Float32TC  

nhdpHystRejectQuality 1.3.6.1.2.1.213.1.1.1.1.10
nhdpHystRejectQuality corresponds to HYST_REJECT of NHDP and represents the link quality threshold below which a link becomes unusable, if it was not already so. Guidance for setting this object may be found in Section 5 of the NHDP specification (RFC 6130), which indicates that: o 0 <= nhdpHystRejectQuality <= nhdpHystAcceptQuality <= 1.0 The default value for this object is 0.0. According to RFC 6340: Since these textual conventions are defined in terms of the OCTET STRING type, the SMI's mechanisms for formally setting range constraints are not available. MIB designers using these textual conventions will need to use DESCRIPTION clauses to spell out any applicable range constraints beyond those implied by the underlying IEEE types. Therefore, this object does not have a DEFVAL clause.
Status: current Access: read-create
OBJECT-TYPE    
  Float32TC  

nhdpInitialQuality 1.3.6.1.2.1.213.1.1.1.1.11
nhdpInitialQuality corresponds to INITIAL_QUALITY of NHDP and represents the initial quality of a newly identified link. Guidance for setting this object may be found in Section 5 of the NHDP specification (RFC 6130), which indicates that: o 0 <= nhdpInitialQuality <= 1.0 The default value for this object is 1.0. According to RFC 6340: Since these textual conventions are defined in terms of the OCTET STRING type, the SMI's mechanisms for formally setting range constraints are not available. MIB designers using these textual conventions will need to use DESCRIPTION clauses to spell out any applicable range constraints beyond those implied by the underlying IEEE types. Therefore, this object does not have a DEFVAL clause.
Status: current Access: read-create
OBJECT-TYPE    
  Float32TC  

nhdpInitialPending 1.3.6.1.2.1.213.1.1.1.1.12
nhdpInitialPending corresponds to INITIAL_PENDING of NHDP. If the value of this object is 'true(1)', then a newly identified link is considered pending and is not usable until the link quality has reached or exceeded the nhdpHystAcceptQuality threshold. Guidance for setting this object may be found in Section 5 of the NHDP specification (RFC 6130), which indicates that: o If nhdpInitialQuality >= nhdpHystAcceptQuality, then nhdpInitialPending := false(2). o If nhdpInitialQuality < nhdpHystRejectQuality, then nhdpInitialPending := true(1).
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

nhdpHpMaxJitter 1.3.6.1.2.1.213.1.1.1.1.13
nhdpHpMaxJitter corresponds to HP_MAXJITTER of NHDP and represents the value of MAXJITTER used in RFC 5148 for periodically generated HELLO messages on this MANET interface. Guidance for setting this object may be found in Section 5 of RFC 5148, which indicates that: o nhdpHpMaxJitter <= nhdpHelloInterval / 2 o nhdpHpMaxJitter should not be greater than nhdpHelloInterval / 4 o If nhdpMinHelloInterval > 0, then nhdpHpMaxJitter <= nhdpHelloMinInterval; and nhdpHpMaxJitter should not be greater than nhdpHelloMinInterval / 2
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

nhdpHtMaxJitter 1.3.6.1.2.1.213.1.1.1.1.14
nhdpHtMaxJitter corresponds to HT_MAXJITTER of NHDP and represents the value of MAXJITTER used in RFC 5148 for externally triggered HELLO messages on this MANET interface. Guidance for setting this object may be found in Section 5 of RFC 5148, which indicates that: o nhdpHtMaxJitter <= nhdpHelloInterval / 2 o nhdpHtMaxJitter should not be greater than nhdpHelloInterval / 4 o If nhdpMinHelloInterval > 0, then nhdpHtMaxJitter <= nhdpHelloMinInterval; and nhdpHtMaxJitter should not be greater than nhdpHelloMinInterval / 2
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

nhdpIfRowStatus 1.3.6.1.2.1.213.1.1.1.1.15
This object permits management of the table by facilitating actions such as row creation, construction, and destruction. The value of this object has no effect on whether other objects in this conceptual row can be modified. An entry may not exist in the 'active(1)' state unless all objects in the entry have a defined appropriate value. For objects with DEFVAL clauses, the management station does not need to specify the value of this object in order for the row to transit to the 'active(1)' state; the default value for this object is used. For objects that do not have DEFVAL clauses, then the network manager MUST specify the value of this object prior to this row transitioning to the 'active(1)' state. When this object transitions to 'active(1)', all objects in this row SHOULD be written to non-volatile (stable) storage. Read-create objects in this row MAY be modified. When an object in a row with nhdpIfRowStatus of 'active(1)' is changed, then the updated value MUST be reflected in NHDP, and this new object value MUST be written to non-volatile storage. If the value of this object is not equal to 'active(1)', all associated entries in the nhdpLibLocalIfSetTable, nhdpInterfaceStateTable, nhdpIibLinkSetTable, and nhdpInterfacePerfTable MUST be deleted.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

nhdpNHoldTime 1.3.6.1.2.1.213.1.1.2
nhdpNHoldTime corresponds to N_HOLD_TIME of NHDP and is used as the period during which former 1-hop neighbor network addresses are advertised as lost in HELLO messages, allowing recipients of these HELLO messages to accelerate removal of this information from their 2-Hop Sets. This object is persistent, and when written, the entity SHOULD save the change to non-volatile storage.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

nhdpIHoldTime 1.3.6.1.2.1.213.1.1.3
nhdpIHoldTime corresponds to I_HOLD_TIME of NHDP and represents the period for which a recently used local interface network address is recorded. This object is persistent, and when written, the entity SHOULD save the change to non-volatile storage.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

nhdpLibLocalIfSetTable 1.3.6.1.2.1.213.1.1.4
A router's Local Interface Set records all network addresses that are defined as local MANET interface network addresses. As such, this table 'sparse augments' the nhdpInterfaceTable when network addresses are being defined for the interfaces existing within the nhdpInterfaceTable. The local interface is defined by the nhdpIfIndex. The Local Interface Set consists of Local Interface Address Tuples per MANET interface and their prefix lengths (in order to determine the network addresses related to the interface). A conceptual row in this table exists if and only if a manager has explicitly created the row. The manager can create a row by setting rowStatus to 'createAndGo' or 'createAndWait'. Further guidance on the addition or removal of local addresses and network addresses is found in Section 9 of RFC 6130.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NhdpLibLocalIfSetEntry

nhdpLibLocalIfSetEntry 1.3.6.1.2.1.213.1.1.4.1
A router's Local Interface Set consists of Configured Interface Address Tuples for each network interface. The objects in this table are persistent, and when written, the device SHOULD save the change to non-volatile storage. For further information on the storage behavior for these objects, refer to the description for the nhdpLibLocalIfSetRowStatus object.
Status: current Access: not-accessible
OBJECT-TYPE    
  NhdpLibLocalIfSetEntry  

nhdpLibLocalIfSetIndex 1.3.6.1.2.1.213.1.1.4.1.1
The index for this table. Necessary because multiple addresses may be associated with a given nhdpIfIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..65535  

nhdpLibLocalIfSetIfIndex 1.3.6.1.2.1.213.1.1.4.1.2
Specifies the local nhdpIfIndex for which this IP address was added.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

nhdpLibLocalIfSetIpAddrType 1.3.6.1.2.1.213.1.1.4.1.3
The type of the nhdpLibLocalIfSetIpAddr in the InetAddress MIB (RFC 4001). Only the values 'ipv4(1)' and 'ipv6(2)' are supported.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressType  

nhdpLibLocalIfSetIpAddr 1.3.6.1.2.1.213.1.1.4.1.4
nhdpLibLocalIfSetIpAddr is an address of an interface of this router. This object is interpreted according to the setting of nhdpLibLocalIfSetIpAddrType.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddress Size(4|16)  

nhdpLibLocalIfSetIpAddrPrefixLen 1.3.6.1.2.1.213.1.1.4.1.5
Indicates the number of leading one bits that form the mask. The mask is logically ANDed to the nhdpLibLocalIfSetIpAddr to determine the address prefix. A row match is true if the address used as an index falls within the network address range defined by the address prefix.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressPrefixLength  

nhdpLibLocalIfSetRowStatus 1.3.6.1.2.1.213.1.1.4.1.6
This object permits management of the table by facilitating actions such as row creation, construction, and destruction. The value of this object has no effect on whether other objects in this conceptual row can be modified. An entry may not exist in the 'active(1)' state unless all read-create objects in the entry have a defined appropriate value. As no objects in this table have DEFVAL clauses, the management station MUST specify the values of all read-create objects prior to this row transitioning to the 'active(1)' state. When this object transitions to 'active(1)', all objects in this row SHOULD be written to non-volatile (stable) storage. Read-create objects in this row MAY be modified. When an object in a row with nhdpIfRowStatus of 'active(1)' is changed, then the updated value MUST be reflected in NHDP, and this new object value MUST be written to non-volatile storage.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

nhdpLibRemovedIfAddrSetTable 1.3.6.1.2.1.213.1.1.5
A router's Removed Interface Address Set records network addresses that were recently used as local interface network addresses. If a router's interface network addresses are immutable, then the Removed Interface Address Set is always empty and may be omitted. It consists of Removed Interface Address Tuples, one per network address.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NhdpLibRemovedIfAddrSetEntry

nhdpLibRemovedIfAddrSetEntry 1.3.6.1.2.1.213.1.1.5.1
A router's Removed Interface Address Set consists of Removed Interface Address Tuples, one per network address: (IR_local_iface_addr, IR_time) The association between these addresses and the router's Interface is found in the Standard MIB II's IP address table (RFC 1213).
Status: current Access: not-accessible
OBJECT-TYPE    
  NhdpLibRemovedIfAddrSetEntry  

nhdpLibRemovedIfAddrSetIndex 1.3.6.1.2.1.213.1.1.5.1.1
The index for this table. Necessary because multiple addresses may be associated with a given nhdpIfIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..65535  

nhdpLibRemovedIfAddrSetIpAddrType 1.3.6.1.2.1.213.1.1.5.1.2
The type of the nhdpLibRemovedIfAddrSetIpAddr in the InetAddress MIB (RFC 4001). Only the values 'ipv4(1)' and 'ipv6(2)' are supported.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

nhdpLibRemovedIfAddrSetIpAddr 1.3.6.1.2.1.213.1.1.5.1.3
nhdpLibRemovedIfAddrSetIpAddr is a recently used address of an interface of this router.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress Size(4|16)  

nhdpLibRemovedIfAddrSetIpAddrPrefixLen 1.3.6.1.2.1.213.1.1.5.1.4
Indicates the number of leading one bits that form the mask. The mask is logically ANDed to the nhdpLibRemovedIfAddrSetIpAddr to determine the address prefix. A row match is true if the address used as an index falls within the network address range defined by the address prefix.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressPrefixLength  

nhdpLibRemovedIfAddrSetIfIndex 1.3.6.1.2.1.213.1.1.5.1.5
Specifies the local IfIndex from which this IP address was recently removed.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

nhdpLibRemovedIfAddrSetIRTime 1.3.6.1.2.1.213.1.1.5.1.6
nhdpLibRemovedIfAddrSetIRTime specifies the value of sysUptime when this entry should expire and be removed from the nhdpLibRemovedIfAddrSetTable.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

nhdpStateObjGrp 1.3.6.1.2.1.213.1.2
OBJECT IDENTIFIER    

nhdpUpTime 1.3.6.1.2.1.213.1.2.1
The value of sysUpTime at the time the current NHDP process was initialized.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

nhdpInterfaceStateTable 1.3.6.1.2.1.213.1.2.2
nhdpInterfaceStateTable lists state information related to specific interfaces of this router. The value of nhdpIfIndex is an ifIndex from the interfaces group defined in the Interfaces Group MIB. The objects in this table are persistent, and when written, the entity SHOULD save the change to non-volatile storage.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NhdpInterfaceStateEntry

nhdpInterfaceStateEntry 1.3.6.1.2.1.213.1.2.2.1
nhdpInterfaceStateEntry describes one NHDP local interface state as indexed by its nhdpIfIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  NhdpInterfaceStateEntry  

nhdpIfStateUpTime 1.3.6.1.2.1.213.1.2.2.1.1
The value of the sysUpTime when NHDP was last initialized on this MANET interface.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

nhdpDiscIfSetTable 1.3.6.1.2.1.213.1.2.3
A router's set of discovered interfaces on neighboring routers.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NhdpDiscIfSetEntry

nhdpDiscIfSetEntry 1.3.6.1.2.1.213.1.2.3.1
The entries include the nhdpDiscRouterIndex of the discovered router, the nhdpDiscIfIndex of the discovered interface, and the current set of addresses associated with this neighbor interface. The nhdpDiscIfIndex uniquely identifies the remote interface address sets through this table. It does not need to be unique across the MANET but MUST be locally unique within this router.
Status: current Access: not-accessible
OBJECT-TYPE    
  NhdpDiscIfSetEntry  

nhdpDiscIfSetIndex 1.3.6.1.2.1.213.1.2.3.1.1
The index for this table. Necessary because multiple addresses may be associated with a given nhdpDiscIfIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..65535  

nhdpDiscIfIndex 1.3.6.1.2.1.213.1.2.3.1.2
The NHDP interface index (locally created) of a neighbor's interface. Used for cross- indexing into other NHDP tables and other MIB modules.
Status: current Access: read-only
OBJECT-TYPE    
  NeighborIfIndex  

nhdpDiscRouterIndex 1.3.6.1.2.1.213.1.2.3.1.3
The NHDP neighbor index (locally created) of a neighboring router. Used for cross- indexing into other NHDP tables and other MIB modules.
Status: current Access: read-only
OBJECT-TYPE    
  NeighborRouterIndex  

nhdpDiscIfSetIpAddrType 1.3.6.1.2.1.213.1.2.3.1.4
The type of the nhdpDiscIfSetIpAddr in the InetAddress MIB (RFC 4001). Only the values 'ipv4(1)' and 'ipv6(2)' are supported.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

nhdpDiscIfSetIpAddr 1.3.6.1.2.1.213.1.2.3.1.5
The nhdpDiscIfSetIpAddr is a recently used address of a neighbor of this router.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress Size(4|16)  

nhdpDiscIfSetIpAddrPrefixLen 1.3.6.1.2.1.213.1.2.3.1.6
Indicates the number of leading one bits that form the mask. The mask is logically ANDed to the nhdpDiscIfSetIpAddr to determine the address prefix. A row match is true if the address used as an index falls within the network address range defined by the address prefix.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressPrefixLength  

nhdpIibLinkSetTable 1.3.6.1.2.1.213.1.2.4
A Link Set of an interface records all links from other routers that are, or recently were, 1-hop neighbors.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NhdpIibLinkSetEntry

nhdpIibLinkSetEntry 1.3.6.1.2.1.213.1.2.4.1
A Link Set consists of Link Tuples, each representing a single link indexed by the local and remote interface pair: (L_neighbor_iface_addr_list, L_HEARD_time, L_SYM_time, L_quality, L_pending, L_lost, L_time). The local interface is indexed via the nhdpIfIndex. The 1-hop interface is indexed via the nhdpDiscIfIndex. There SHOULD be an entry in this table for each local interface and associated 1-hop neighbor reachable on this local interface. Note that L_quality is not included in the entries below, because updates may be required too frequently.
Status: current Access: not-accessible
OBJECT-TYPE    
  NhdpIibLinkSetEntry  

nhdpIibLinkSetLHeardTime 1.3.6.1.2.1.213.1.2.4.1.1
nhdpIibLinkSetLHeardTime corresponds to L_HEARD_time of NHDP and represents the time up to which the MANET interface of the 1-hop neighbor would be considered heard if not considering link quality.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

nhdpIibLinkSetLSymTime 1.3.6.1.2.1.213.1.2.4.1.2
nhdpIibLinkSetLSymTime corresponds to L_SYM_time of NHDP and represents the time up to which the link to the 1-hop neighbor would be considered symmetric if not considering link quality.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

nhdpIibLinkSetLPending 1.3.6.1.2.1.213.1.2.4.1.3
nhdpIibLinkSetLPending corresponds to L_pending of NHDP and is a boolean flag, describing if a link is considered pending (i.e., a candidate, but not yet established, link).
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

nhdpIibLinkSetLLost 1.3.6.1.2.1.213.1.2.4.1.4
nhdpIibLinkSetLLost corresponds to L_lost of NHDP and is a boolean flag, describing if a link is considered lost due to low link quality.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

nhdpIibLinkSetLTime 1.3.6.1.2.1.213.1.2.4.1.5
nhdpIibLinkSetLTime specifies the value of sysUptime when this entry should expire and be removed from the nhdpIibLinkSetTable.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

nhdpIib2HopSetTable 1.3.6.1.2.1.213.1.2.5
A 2-Hop Set of an interface records network addresses of symmetric 2-hop neighbors and the symmetric links to symmetric 1-hop neighbors through which these symmetric 2-hop neighbors can be reached. It consists of 2-Hop Tuples.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NhdpIib2HopSetEntry

nhdpIib2HopSetEntry 1.3.6.1.2.1.213.1.2.5.1
nhdpIib2HopSetTable consists of 2-Hop Tuples, each representing a single network address of a symmetric 2-hop neighbor and a single MANET interface of a symmetric 1-hop neighbor. (N2_neighbor_iface_addr_list, N2_2hop_addr, N2_time). The entries include the 2-hop neighbor addresses, which act as the table index, and associated 1-hop symmetric link address set, designated through nhdpDiscIfIndex, and an expiration time. The nhdpIfIndex in the INDEX is the interface index of the local interface through which these 2-hop addresses are accessible. The nhdpDiscIfIndex in the INDEX represents the 1-hop neighbor interface through which these 2-hop addresses are reachable.
Status: current Access: not-accessible
OBJECT-TYPE    
  NhdpIib2HopSetEntry  

nhdpIib2HopSetIpAddressType 1.3.6.1.2.1.213.1.2.5.1.1
The type of the nhdpIib2HopSetIpAddress in the InetAddress MIB module (RFC 4001). Only the values 'ipv4(1)' and 'ipv6(2)' are supported.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddressType  

nhdpIib2HopSetIpAddress 1.3.6.1.2.1.213.1.2.5.1.2
nhdpIib2HopSetIpAddr corresponds to N2_2hop_addr of NHDP and is a network address of a symmetric 2-hop neighbor that has a symmetric link (using any MANET interface) to the indicated symmetric 1-hop neighbor.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddress Size(4|16)  

nhdpIib2HopSetIpAddrPrefixLen 1.3.6.1.2.1.213.1.2.5.1.3
Indicates the number of leading one bits that form the mask. The mask is logically ANDed to the nhdpIib2HopSetIpAddress to determine the address prefix. A row match is true if the address used as an index falls within the network address range defined by the address prefix.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressPrefixLength  

nhdpIib2HopSet1HopIfIndex 1.3.6.1.2.1.213.1.2.5.1.4
nhdpIib2HopSet1HopIfIndex is nhdpDiscIfIndex of the 1-hop neighbor that communicated the ipAddress of the 2-hop neighbor in this row entry.
Status: current Access: read-only
OBJECT-TYPE    
  NeighborIfIndex  

nhdpIib2HopSetN2Time 1.3.6.1.2.1.213.1.2.5.1.5
nhdpIib2HopSetN2Time specifies the value of sysUptime when this entry should expire and be removed from the nhdpIib2HopSetTable.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

nhdpNibNeighborSetTable 1.3.6.1.2.1.213.1.2.6
A router's Neighbor Set records all network addresses of each 1-hop neighbor.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NhdpNibNeighborSetEntry

nhdpNibNeighborSetEntry 1.3.6.1.2.1.213.1.2.6.1
A router's Neighbor Set consists of Neighbor Tuples, each representing a single 1-hop neighbor: (N_neighbor_addr_list, N_symmetric)
Status: current Access: not-accessible
OBJECT-TYPE    
  NhdpNibNeighborSetEntry  

nhdpNibNeighborSetNSymmetric 1.3.6.1.2.1.213.1.2.6.1.1
nhdpNibNeighborNSymmetric corresponds to N_symmetric of NHDP and is a boolean flag, describing if this is a symmetric 1-hop neighbor.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

nhdpNibLostNeighborSetTable 1.3.6.1.2.1.213.1.2.7
A router's Lost Neighbor Set records network addresses of routers that were recently symmetric 1-hop neighbors but are now advertised as lost.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NhdpNibLostNeighborSetEntry

nhdpNibLostNeighborSetEntry 1.3.6.1.2.1.213.1.2.7.1
A router's Lost Neighbor Set consists of Lost Neighbor Tuples, each representing a single such network address: (NL_neighbor_addr, NL_time)
Status: current Access: not-accessible
OBJECT-TYPE    
  NhdpNibLostNeighborSetEntry  

nhdpNibLostNeighborSetNLTime 1.3.6.1.2.1.213.1.2.7.1.1
nhdpNibLostNeighborSetNLTime specifies the value of sysUptime when this entry should expire and be removed from the nhdpNibLostNeighborSetTable.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

nhdpPerformanceObjGrp 1.3.6.1.2.1.213.1.3
OBJECT IDENTIFIER    

nhdpInterfacePerfTable 1.3.6.1.2.1.213.1.3.1
This table summarizes performance objects that are measured per local NHDP interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NhdpInterfacePerfEntry

nhdpInterfacePerfEntry 1.3.6.1.2.1.213.1.3.1.1
A single entry contains performance counters for a local NHDP interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  NhdpInterfacePerfEntry  

nhdpIfHelloMessageXmits 1.3.6.1.2.1.213.1.3.1.1.1
A counter is incremented each time a HELLO message has been transmitted on that interface.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nhdpIfHelloMessageRecvd 1.3.6.1.2.1.213.1.3.1.1.2
A counter is incremented each time a HELLO message has been received on that interface.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nhdpIfHelloMessageXmitAccumulatedSize 1.3.6.1.2.1.213.1.3.1.1.3
A counter is incremented by the number of octets in a HELLO message each time a HELLO message has been sent.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

nhdpIfHelloMessageRecvdAccumulatedSize 1.3.6.1.2.1.213.1.3.1.1.4
A counter is incremented by the number of octets in a HELLO message each time a HELLO message has been received.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

nhdpIfHelloMessageTriggeredXmits 1.3.6.1.2.1.213.1.3.1.1.5
A counter is incremented each time a triggered HELLO message has been sent.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nhdpIfHelloMessagePeriodicXmits 1.3.6.1.2.1.213.1.3.1.1.6
A counter is incremented each time a periodic HELLO message has been sent.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nhdpIfHelloMessageXmitAccumulatedSymmetricNeighborCount 1.3.6.1.2.1.213.1.3.1.1.7
A counter is incremented by the number of advertised symmetric neighbors in a HELLO each time a HELLO message has been sent.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nhdpIfHelloMessageXmitAccumulatedHeardNeighborCount 1.3.6.1.2.1.213.1.3.1.1.8
A counter is incremented by the number of advertised heard neighbors in a HELLO each time a HELLO message has been sent.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nhdpIfHelloMessageXmitAccumulatedLostNeighborCount 1.3.6.1.2.1.213.1.3.1.1.9
A counter is incremented by the number of advertised lost neighbors in a HELLO each time a HELLO message has been sent.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nhdpDiscIfSetPerfTable 1.3.6.1.2.1.213.1.3.2
A router's set of performance properties for each discovered interface of a neighbor.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NhdpDiscIfSetPerfEntry

nhdpDiscIfSetPerfEntry 1.3.6.1.2.1.213.1.3.2.1
There is an entry for each discovered interface of a neighbor.
Status: current Access: not-accessible
OBJECT-TYPE    
  NhdpDiscIfSetPerfEntry  

nhdpDiscIfRecvdPackets 1.3.6.1.2.1.213.1.3.2.1.1
This counter increments each time this router receives a packet from that interface of the neighbor.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nhdpDiscIfExpectedPackets 1.3.6.1.2.1.213.1.3.2.1.2
This counter increments by the number of missed packets from this neighbor based on the packet sequence number each time this router receives a packet from that interface of the neighbor.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nhdpNibNeighborSetChanges 1.3.6.1.2.1.213.1.3.3
This counter increments each time the Neighbor Set changes. A change occurs whenever a new Neighbor Tuple has been added, a Neighbor Tuple has been removed, or any entry of a Neighbor Tuple has been modified.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nhdpDiscNeighborSetPerfTable 1.3.6.1.2.1.213.1.3.4
A router's set of discovered neighbors and their properties.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NhdpDiscNeighborSetPerfEntry

nhdpDiscNeighborSetPerfEntry 1.3.6.1.2.1.213.1.3.4.1
The entries include the nhdpDiscRouterIndex of the discovered router as well as performance objects related to changes of the Neighbor Set.
Status: current Access: not-accessible
OBJECT-TYPE    
  NhdpDiscNeighborSetPerfEntry  

nhdpDiscNeighborNibNeighborSetChanges 1.3.6.1.2.1.213.1.3.4.1.1
This object returns the number of changes to the given Neighbor Tuple.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nhdpDiscNeighborNibNeighborSetUpTime 1.3.6.1.2.1.213.1.3.4.1.2
This object returns the sysUpTime when the neighbor becomes 'nbrup'. A neighbor is said to become 'nbrup' if a new nhdpNibNeighborSetEntry is created for a particular nhdpNibNeighborSetRouterIndex. It becomes 'nbrdown' if the entry for that neighbor has been deleted.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

nhdpDiscNeighborNibNeighborSetReachableLinkChanges 1.3.6.1.2.1.213.1.3.4.1.3
This object counts each time the neighbor changes the interface(s) over which it is reachable. A change in the set of Link Tuples corresponding to the appropriate Neighbor Tuple is registered, i.e., a corresponding Link Tuple is added or removed from the set of all corresponding Link Tuples.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nhdpIib2HopSetPerfTable 1.3.6.1.2.1.213.1.3.5
This table contains performance objects per discovered 2-hop neighbor.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NhdpIib2HopSetPerfEntry

nhdpIib2HopSetPerfEntry 1.3.6.1.2.1.213.1.3.5.1
The entries contain performance objects per discovered 2-hop neighbor.
Status: current Access: not-accessible
OBJECT-TYPE    
  NhdpIib2HopSetPerfEntry  

nhdpIib2HopSetPerfChanges 1.3.6.1.2.1.213.1.3.5.1.1
This object counts the changes of the union of all N2_neighbor_iface_addr_list of 2-Hop Tuples with an N2_2hop_addr equal to one of the given 2-hop neighbor's addresses.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nhdpIib2HopSetPerfUpTime 1.3.6.1.2.1.213.1.3.5.1.2
This object returns the sysUpTime when the 2-Hop Tuple corresponding to the given 2-hop neighbor IP address was registered in the nhdpIib2HopSetTable.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

nhdpNotificationsObjects 1.3.6.1.2.1.213.0.0
OBJECT IDENTIFIER    

nhdpNotificationsControl 1.3.6.1.2.1.213.0.1
OBJECT IDENTIFIER    

nhdpNotificationsStates 1.3.6.1.2.1.213.0.2
OBJECT IDENTIFIER    

nhdpNbrStateChange 1.3.6.1.2.1.213.0.0.1
nhdpNbrStateChange is a notification sent when more than nhdpNbrStateChangeThreshold neighbors change their status (i.e., 'down(0)', 'asymmetric(1)', or 'symmetric(2)') within a time window of nhdpNbrStateChangeWindow.
Status: current Access: read-only
NOTIFICATION-TYPE    

nhdp2HopNbrStateChange 1.3.6.1.2.1.213.0.0.2
nhdp2HopNbrStateChange is a notification sent when more than nhdp2HopNbrStateChangeThreshold 2-hop neighbors change their status (i.e., 'down(0)' or 'up(1)') within a time window of nhdp2HopNbrStateChangeWindow.
Status: current Access: read-only
NOTIFICATION-TYPE    

nhdpIfStateChange 1.3.6.1.2.1.213.0.0.3
nhdpIfStateChange is a notification sent when nhdpIfStatus has changed on this interface.
Status: current Access: read-only
NOTIFICATION-TYPE    

nhdpNbrStateChangeThreshold 1.3.6.1.2.1.213.0.1.1
A threshold value for the nhdpNbrStateChange object. If the number of occurrences exceeds this threshold within the previous nhdpNbrStateChangeWindow, then the nhdpNbrStateChange notification is to be sent. It is recommended that the value of this threshold be set to at least 10 and higher in dense topologies with frequent expected topology changes.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..255  

nhdpNbrStateChangeWindow 1.3.6.1.2.1.213.0.1.2
A time window for the nhdpNbrStateChange object. If the number of occurrences exceeds the nhdpNbrStateChangeThreshold within the previous nhdpNbrStateChangeWindow, then the nhdpNbrStateChange notification is to be sent. It is recommended that the value for this window be set to at least 5 times the nhdpHelloInterval. This object represents the time in hundredths of a second.
Status: current Access: read-write
OBJECT-TYPE    
  TimeTicks  

nhdp2HopNbrStateChangeThreshold 1.3.6.1.2.1.213.0.1.3
A threshold value for the nhdp2HopNbrStateChange object. If the number of occurrences exceeds this threshold within the previous nhdp2HopNbrStateChangeWindow, then the nhdp2HopNbrStateChange notification is to be sent. It is recommended that the value of this threshold be set to at least 10 and higher when topologies are expected to be highly dynamic.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..255  

nhdp2HopNbrStateChangeWindow 1.3.6.1.2.1.213.0.1.4
A time window for the nhdp2HopNbrStateChange object. If the number of occurrences exceeds the nhdp2HopNbrStateChangeThreshold within the previous nhdp2HopNbrStateChangeWindow, then the nhdp2HopNbrStateChange notification is to be sent. It is recommended that the value for this window be set to at least 5 times nhdpHelloInterval. This object represents the time in hundredths of a second.
Status: current Access: read-write
OBJECT-TYPE    
  TimeTicks  

nhdpNbrState 1.3.6.1.2.1.213.0.2.1
NHDP neighbor states. In NHDP, it is not necessary to remove Protocol Tuples from Protocol Sets at the exact time indicated, only to behave as if the Protocol Tuples were removed at that time. This case is indicated here as 'down(0)', all other cases being indicated as 'asymmetric(1)' or 'symmetric(2)'. If 'down(0)', the direct neighbor is also added to the nhdpNibLostNeighborSetTable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER down(0), asymmetric(1), symmetric(2)  

nhdp2HopNbrState 1.3.6.1.2.1.213.0.2.2
NHDP 2-hop neighbor states. In NHDP, it is not necessary to remove Protocol Tuples from Protocol Sets at the exact time indicated, only to behave as if the Protocol Tuples were removed at that time. This case is indicated here as 'down(0)'; otherwise, it is 'up(1)'.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER down(0), up(1)  

nhdpCompliances 1.3.6.1.2.1.213.2.1
OBJECT IDENTIFIER    

nhdpMIBGroups 1.3.6.1.2.1.213.2.2
OBJECT IDENTIFIER    

nhdpBasicCompliance 1.3.6.1.2.1.213.2.1.1
The basic implementation requirements for managed network entities that implement NHDP.
Status: current Access: read-only
MODULE-COMPLIANCE    

nhdpFullCompliance 1.3.6.1.2.1.213.2.1.2
The full implementation requirements for managed network entities that implement NHDP.
Status: current Access: read-only
MODULE-COMPLIANCE    

nhdpConfigurationGroup 1.3.6.1.2.1.213.2.2.2
Set of NHDP configuration objects implemented in this module.
Status: current Access: read-only
OBJECT-GROUP    

nhdpStateGroup 1.3.6.1.2.1.213.2.2.3
Set of NHDP state objects implemented in this module.
Status: current Access: read-only
OBJECT-GROUP    

nhdpPerformanceGroup 1.3.6.1.2.1.213.2.2.4
Set of NHDP performance objects implemented in this module.
Status: current Access: read-only
OBJECT-GROUP    

nhdpNotificationObjectGroup 1.3.6.1.2.1.213.2.2.5
Set of NHDP notification objects implemented in this module.
Status: current Access: read-only
OBJECT-GROUP    

nhdpNotificationGroup 1.3.6.1.2.1.213.2.2.6
Set of NHDP notifications implemented in this module.
Status: current Access: read-only
NOTIFICATION-GROUP