NGDSL-LINE-MIB

File: NGDSL-LINE-MIB.mib (218986 bytes)

Imported modules

SNMPv2-SMI IF-MIB SNMPv2-TC
SNMP-FRAMEWORK-MIB HC-PerfHist-TC-MIB NGDSL-LINE-TC-MIB
ADSL2-LINE-TC-MIB SNMPv2-CONF

Imported symbols

MODULE-IDENTITY OBJECT-TYPE transmission
Unsigned32 NOTIFICATION-TYPE Integer32
Counter32 ifIndex TruthValue
RowStatus SnmpAdminString HCPerfIntervalThreshold
HCPerfTimeElapsed Adsl2Unit Adsl2Direction
Adsl2TransmissionModeType Adsl2RaMode Adsl2InitResult
Adsl2OperationModes Adsl2PowerMngState Adsl2ConfPmsForce
Adsl2LConfProfPmMode Adsl2LineLdsf Adsl2LdsfResult
Adsl2SymbolProtection Adsl2MaxBer Adsl2ScMaskDs
Adsl2ScMaskUs Adsl2RfiDs Adsl2PsdMaskDs
Adsl2PsdMaskUs Adsl2Tssi Adsl2LastTransmittedState
Adsl2LineStatus Adsl2ChAtmStatus Adsl2ChPtmStatus
allowTransitionsToIdle allowTransitionsToLowPower MODULE-COMPLIANCE
OBJECT-GROUP NOTIFICATION-GROUP

Defined Types

Adsl2LineEntry  
SEQUENCE    
  adsl2LineCnfgTemplate SnmpAdminString
  adsl2LineAlarmCnfgTemplate SnmpAdminString
  adsl2LineCmndConfPmsf Adsl2ConfPmsForce
  adsl2LineCmndConfLdsf Adsl2LineLdsf
  adsl2LineCmndConfLdsfFailReason Adsl2LdsfResult
  adsl2LineCmndAutomodeColdStart TruthValue
  adsl2LineStatusAtuTransSys Adsl2TransmissionModeType
  adsl2LineStatusPwrMngState Adsl2PowerMngState
  adsl2LineStatusInitResult Adsl2InitResult
  adsl2LineStatusLastStateDs Adsl2LastTransmittedState
  adsl2LineStatusLastStateUs Adsl2LastTransmittedState
  adsl2LineStatusAtur Adsl2LineStatus
  adsl2LineStatusAtuc Adsl2LineStatus
  adsl2LineStatusLnAttenDs Unsigned32
  adsl2LineStatusLnAttenUs Unsigned32
  adsl2LineStatusSigAttenDs Unsigned32
  adsl2LineStatusSigAttenUs Unsigned32
  adsl2LineStatusSnrMarginDs Integer32
  adsl2LineStatusSnrMarginUs Integer32
  adsl2LineStatusAttainableRateDs Unsigned32
  adsl2LineStatusAttainableRateUs Unsigned32
  adsl2LineStatusActPsdDs Integer32
  adsl2LineStatusActPsdUs Integer32
  adsl2LineStatusActAtpDs Integer32
  adsl2LineStatusActAtpUs Integer32

Adsl2ChannelStatusEntry  
SEQUENCE    
  adsl2ChStatusUnit Adsl2Unit
  adsl2ChStatusChannelNum Unsigned32
  adsl2ChStatusActDataRate Unsigned32
  adsl2ChStatusPrevDataRate Unsigned32
  adsl2ChStatusActDelay Unsigned32
  adsl2ChStatusAtmStatus Adsl2ChAtmStatus
  adsl2ChStatusPtmStatus Adsl2ChPtmStatus

Adsl2SCStatusEntry  
SEQUENCE    
  adsl2SCStatusDirection Adsl2Direction
  adsl2SCStatusMtime Unsigned32
  adsl2SCStatusSnr OCTET STRING
  adsl2SCStatusBitsAlloc OCTET STRING
  adsl2SCStatusGainAlloc OCTET STRING
  adsl2SCStatusTssi Adsl2Tssi
  adsl2SCStatusLinScale Unsigned32
  adsl2SCStatusLinReal OCTET STRING
  adsl2SCStatusLinImg OCTET STRING
  adsl2SCStatusLogMt Unsigned32
  adsl2SCStatusLog OCTET STRING
  adsl2SCStatusQlnMt Unsigned32
  adsl2SCStatusQln OCTET STRING
  adsl2SCStatusLnAtten Unsigned32
  adsl2SCStatusSigAtten Unsigned32
  adsl2SCStatusSnrMargin Integer32
  adsl2SCStatusAttainableRate Unsigned32
  adsl2SCStatusActAtp Integer32
  adsl2SCStatusRowStatus RowStatus

Adsl2LineInventoryEntry  
SEQUENCE    
  adsl2LInvUnit Adsl2Unit
  adsl2LInvG994VendorId OCTET STRING
  adsl2LInvSystemVendorId OCTET STRING
  adsl2LInvVersionNumber OCTET STRING
  adsl2LInvSerialNumber OCTET STRING
  adsl2LInvSelfTestResult OCTET STRING
  adsl2LInvTransmissionCapabilities Adsl2TransmissionModeType

Adsl2LineConfTemplateEntry  
SEQUENCE    
  adsl2LConfTempTemplateName SnmpAdminString
  adsl2LConfTempLineProfile SnmpAdminString
  adsl2LConfTempChan1ConfProfile SnmpAdminString
  adsl2LConfTempChan1RaRatioDs Unsigned32
  adsl2LConfTempChan1RaRatioUs Unsigned32
  adsl2LConfTempChan2ConfProfile SnmpAdminString
  adsl2LConfTempChan2RaRatioDs Unsigned32
  adsl2LConfTempChan2RaRatioUs Unsigned32
  adsl2LConfTempChan3ConfProfile SnmpAdminString
  adsl2LConfTempChan3RaRatioDs Unsigned32
  adsl2LConfTempChan3RaRatioUs Unsigned32
  adsl2LConfTempChan4ConfProfile SnmpAdminString
  adsl2LConfTempChan4RaRatioDs Unsigned32
  adsl2LConfTempChan4RaRatioUs Unsigned32
  adsl2LConfTempRowStatus RowStatus

Adsl2LineConfProfEntry  
SEQUENCE    
  adsl2LConfProfProfileName SnmpAdminString
  adsl2LConfProfScMaskDs Adsl2ScMaskDs
  adsl2LConfProfScMaskUs Adsl2ScMaskUs
  adsl2LConfProfRfiBandsDs Adsl2RfiDs
  adsl2LConfProfRaModeDs Adsl2RaMode
  adsl2LConfProfRaModeUs Adsl2RaMode
  adsl2LConfProfRaUsNrmDs Unsigned32
  adsl2LConfProfRaUsNrmUs Unsigned32
  adsl2LConfProfRaUsTimeDs Unsigned32
  adsl2LConfProfRaUsTimeUs Unsigned32
  adsl2LConfProfRaDsNrmsDs Unsigned32
  adsl2LConfProfRaDsNrmsUs Unsigned32
  adsl2LConfProfRaDsTimeDs Unsigned32
  adsl2LConfProfRaDsTimeUs Unsigned32
  adsl2LConfProfTargetSnrmDs Unsigned32
  adsl2LConfProfTargetSnrmUs Unsigned32
  adsl2LConfProfMaxSnrmDs Unsigned32
  adsl2LConfProfMaxSnrmUs Unsigned32
  adsl2LConfProfMinSnrmDs Unsigned32
  adsl2LConfProfMinSnrmUs Unsigned32
  adsl2LConfProfMsgMinUs Unsigned32
  adsl2LConfProfMsgMinDs Unsigned32
  adsl2LConfProfAtuTransSysEna Adsl2TransmissionModeType
  adsl2LConfProfPmMode Adsl2LConfProfPmMode
  adsl2LConfProfL0Time Unsigned32
  adsl2LConfProfL2Time Unsigned32
  adsl2LConfProfL2Atpr Unsigned32
  adsl2LConfProfL2Atprt Unsigned32
  adsl2LConfProfRowStatus RowStatus

Adsl2LineConfProfModeSpecEntry  
SEQUENCE    
  adsl2LconfProfAdslMode Adsl2OperationModes
  adsl2LConfProfMaxNomPsdDs Integer32
  adsl2LConfProfMaxNomPsdUs Integer32
  adsl2LConfProfMaxNomAtpDs Unsigned32
  adsl2LConfProfMaxNomAtpUs Unsigned32
  adsl2LConfProfMaxAggRxPwrUs Integer32
  adsl2LConfProfPsdMaskDs Adsl2PsdMaskDs
  adsl2LConfProfPsdMaskUs Adsl2PsdMaskUs
  adsl2LConfProfPsdMaskSelectUs Unsigned32
  adsl2LConfProfModeSpecRowStatus RowStatus

Adsl2ChConfProfileEntry  
SEQUENCE    
  adsl2ChConfProfProfileName SnmpAdminString
  adsl2ChConfProfMinDataRateDs Unsigned32
  adsl2ChConfProfMinDataRateUs Unsigned32
  adsl2ChConfProfMinResDataRateDs Unsigned32
  adsl2ChConfProfMinResDataRateUs Unsigned32
  adsl2ChConfProfMaxDataRateDs Unsigned32
  adsl2ChConfProfMaxDataRateUs Unsigned32
  adsl2ChConfProfMinDataRateLowPwrDs Unsigned32
  adsl2ChConfProfMinDataRateLowPwrUs Unsigned32
  adsl2ChConfProfMaxDelayDs Unsigned32
  adsl2ChConfProfMaxDelayUs Unsigned32
  adsl2ChConfProfMinProtectionDs Adsl2SymbolProtection
  adsl2ChConfProfMinProtectionUs Adsl2SymbolProtection
  adsl2ChConfProfMaxBerDs Adsl2MaxBer
  adsl2ChConfProfMaxBerUs Adsl2MaxBer
  adsl2ChConfProfUsDataRateDs Unsigned32
  adsl2ChConfProfDsDataRateDs Unsigned32
  adsl2ChConfProfUsDataRateUs Unsigned32
  adsl2ChConfProfDsDataRateUs Unsigned32
  adsl2ChConfProfImaEnabled TruthValue
  adsl2ChConfProfRowStatus RowStatus

Adsl2LineAlarmConfTemplateEntry  
SEQUENCE    
  adsl2LAlarmConfTempTemplateName SnmpAdminString
  adsl2LAlarmConfTempLineProfile SnmpAdminString
  adsl2LAlarmConfTempChan1ConfProfile SnmpAdminString
  adsl2LAlarmConfTempChan2ConfProfile SnmpAdminString
  adsl2LAlarmConfTempChan3ConfProfile SnmpAdminString
  adsl2LAlarmConfTempChan4ConfProfile SnmpAdminString
  adsl2LAlarmConfTempRowStatus RowStatus

Adsl2LineAlarmConfProfileEntry  
SEQUENCE    
  adsl2LineAlarmConfProfileName SnmpAdminString
  adsl2LineAlarmConfProfileAtucThresh15MinFecs HCPerfIntervalThreshold
  adsl2LineAlarmConfProfileAtucThresh15MinEs HCPerfIntervalThreshold
  adsl2LineAlarmConfProfileAtucThresh15MinSes HCPerfIntervalThreshold
  adsl2LineAlarmConfProfileAtucThresh15MinLoss HCPerfIntervalThreshold
  adsl2LineAlarmConfProfileAtucThresh15MinUas HCPerfIntervalThreshold
  adsl2LineAlarmConfProfileAturThresh15MinFecs HCPerfIntervalThreshold
  adsl2LineAlarmConfProfileAturThresh15MinEs HCPerfIntervalThreshold
  adsl2LineAlarmConfProfileAturThresh15MinSes HCPerfIntervalThreshold
  adsl2LineAlarmConfProfileAturThresh15MinLoss HCPerfIntervalThreshold
  adsl2LineAlarmConfProfileAturThresh15MinUas HCPerfIntervalThreshold
  adsl2LineAlarmConfProfileThresh15MinFailedFullInt Unsigned32
  adsl2LineAlarmConfProfileThresh15MinFailedShrtInt Unsigned32
  adsl2LineAlarmConfProfileRowStatus RowStatus

Adsl2ChAlarmConfProfileEntry  
SEQUENCE    
  adsl2ChAlarmConfProfileName SnmpAdminString
  adsl2ChAlarmConfProfileAtucThresh15MinCodingViolations Unsigned32
  adsl2ChAlarmConfProfileAtucThresh15MinCorrected Unsigned32
  adsl2ChAlarmConfProfileAturThresh15MinCodingViolations Unsigned32
  adsl2ChAlarmConfProfileAturThresh15MinCorrected Unsigned32
  adsl2ChAlarmConfProfileRowStatus RowStatus

Adsl2PMLineCurrEntry  
SEQUENCE    
  adsl2PMLCurrUnit Adsl2Unit
  adsl2PMLCurrValidIntervals Unsigned32
  adsl2PMLCurrInvalidIntervals Unsigned32
  adsl2PMLCurr15MTimeElapsed HCPerfTimeElapsed
  adsl2PMLCurr15MFecs Counter32
  adsl2PMLCurr15MEs Counter32
  adsl2PMLCurr15MSes Counter32
  adsl2PMLCurr15MLoss Counter32
  adsl2PMLCurr15MUas Counter32
  adsl2PMLCurr1DayValidIntervals Unsigned32
  adsl2PMLCurr1DayInvalidIntervals Unsigned32
  adsl2PMLCurr1DayTimeElapsed HCPerfTimeElapsed
  adsl2PMLCurr1DayFecs Counter32
  adsl2PMLCurr1DayEs Counter32
  adsl2PMLCurr1DaySes Counter32
  adsl2PMLCurr1DayLoss Counter32
  adsl2PMLCurr1DayUas Counter32

Adsl2PMLineCurrInitEntry  
SEQUENCE    
  adsl2PMLCurrInit15MTimeElapsed Unsigned32
  adsl2PMLCurrInit15MFullInits Unsigned32
  adsl2PMLCurrInit15MFailedFullInits Unsigned32
  adsl2PMLCurrInit15MShortInits Unsigned32
  adsl2PMLCurrInit15MFailedShortInits Unsigned32
  adsl2PMLCurrInit1DayTimeElapsed Unsigned32
  adsl2PMLCurrInit1DayFullInits Unsigned32
  adsl2PMLCurrInit1DayFailedFullInits Unsigned32
  adsl2PMLCurrInit1DayShortInits Unsigned32
  adsl2PMLCurrInit1DayFailedShortInits Unsigned32

Adsl2PMLineHist15MinEntry  
SEQUENCE    
  adsl2PMLHist15MUnit Adsl2Unit
  adsl2PMLHist15MInterval Unsigned32
  adsl2PMLHist15MMonitoredTime Unsigned32
  adsl2PMLHist15MFecs Counter32
  adsl2PMLHist15MEs Counter32
  adsl2PMLHist15MSes Counter32
  adsl2PMLHist15MLoss Counter32
  adsl2PMLHist15MUas Counter32
  adsl2PMLHist15MValidInterval TruthValue

Adsl2PMLineHist1DayEntry  
SEQUENCE    
  adsl2PMLHist1DUnit Adsl2Unit
  adsl2PMLHist1DInterval Unsigned32
  adsl2PMLHist1DMonitoredTime Unsigned32
  adsl2PMLHist1DFecs Counter32
  adsl2PMLHist1DEs Counter32
  adsl2PMLHist1DSes Counter32
  adsl2PMLHist1DLoss Counter32
  adsl2PMLHist1DUas Counter32
  adsl2PMLHist1DValidInterval TruthValue

Adsl2PMLineInitHist15MinEntry  
SEQUENCE    
  adsl2PMLHistInit15MInterval Unsigned32
  adsl2PMLHistInit15MMonitoredTime Unsigned32
  adsl2PMLHistInit15MFullInits Unsigned32
  adsl2PMLHistInit15MFailedFullInits Unsigned32
  adsl2PMLHistInit15MShortInits Unsigned32
  adsl2PMLHistInit15MFailedShortInits Unsigned32
  adsl2PMLHistInit15MValidInterval TruthValue

Adsl2PMLineInitHist1DayEntry  
SEQUENCE    
  adsl2PMLHistinit1DInterval Unsigned32
  adsl2PMLHistinit1DMonitoredTime Unsigned32
  adsl2PMLHistinit1DFullInits Unsigned32
  adsl2PMLHistinit1DFailedFullInits Unsigned32
  adsl2PMLHistinit1DShortInits Unsigned32
  adsl2PMLHistinit1DFailedShortInits Unsigned32
  adsl2PMLHistinit1DValidInterval TruthValue

Adsl2PMChCurrEntry  
SEQUENCE    
  adsl2PMChCurrUnit Adsl2Unit
  adsl2PMChCurrValidIntervals Unsigned32
  adsl2PMChCurrInvalidIntervals Unsigned32
  adsl2PMChCurr15MTimeElapsed HCPerfTimeElapsed
  adsl2PMChCurr15MCodingViolations Unsigned32
  adsl2PMChCurr15MCorrectedBlocks Unsigned32
  adsl2PMChCurr1DayValidIntervals Unsigned32
  adsl2PMChCurr1DayInvalidIntervals Unsigned32
  adsl2PMChCurr1DayTimeElapsed HCPerfTimeElapsed
  adsl2PMChCurr1DayCodingViolations Unsigned32
  adsl2PMChCurr1DayCorrectedBlocks Unsigned32

Adsl2PMChHist15MinEntry  
SEQUENCE    
  adsl2PMChHist15MUnit Adsl2Unit
  adsl2PMChHist15MInterval Unsigned32
  adsl2PMChHist15MMonitoredTime Unsigned32
  adsl2PMChHist15MCodingViolations Unsigned32
  adsl2PMChHist15MCorrectedBlocks Unsigned32
  adsl2PMChHist15MValidInterval TruthValue

Adsl2PMChHist1DEntry  
SEQUENCE    
  adsl2PMChHist1DUnit Adsl2Unit
  adsl2PMChHist1DInterval Unsigned32
  adsl2PMChHist1DMonitoredTime Unsigned32
  adsl2PMChHist1DCodingViolations Unsigned32
  adsl2PMChHist1DCorrectedBlocks Unsigned32
  adsl2PMChHist1DValidInterval TruthValue

Defined Values

ngdslMIB 1.3.6.1.2.1.10.1
This document defines a Management Information Base (MIB) module for use with network management protocols in the Internet community for the purpose of managing ADSL, ADSL2, and ADSL2+ lines. The MIB module described in RFC 2662 [RFC2662] describes objects used for managing Asymmetric Bit-Rate DSL (ADSL) interfaces per [T1E1.413], [G.992.1], and [G.992.2]. These object descriptions are based upon the specifications for the ADSL Embedded Operations Channel (EOC) as defined in American National Standards Institute (ANSI) T1E1.413/1995 [T1E1.413] and International Telecommunication Union (ITU-T) G.992.1 [G.992.1] and G.992.2 [G.992.2]. This document does not obsolete RFC 2662 [RFC2662], but rather provides a more comprehensive management model that includes the ADSL2 and ADSL2+ technologies per G.992.3, G.992.4, and G.992.5 ([G.992.3], [G.992.4], and [G.992.5], respectively). In addition, objects have been added to improve the management of ADSL, ADSL2, and ADSL2+ lines. Additionally, the management framework for New Generation ADSL lines specified by the Digital Subscriber Line Forum (DSLF) has been taken into consideration [TR-90]. That framework is based on ITU-T G.997.1 standard [G.997.1] as well as two amendments: [G.997.1 am1] and [G.997.1 am2]. Note that the revised ITU-T G.997.1 standard refers also to next generation of VDSL technology, known as VDSL2, per ITU-T G.993.2 [G.993.2]. However, managing VDSL2 lines is currently beyond the scope of this document. The MIB module is located in the MIB tree under MIB 2 transmission, as discussed in the MIB-2 Integration (RFC 2863 [RFC2863]) section of this document. Copyright (C) The Internet Society (2005). This version of this MIB module is part of RFC XXXX: see the RFC itself for full legal notices.
MODULE-IDENTITY    

adsl2 1.3.6.1.2.1.10.1.1
OBJECT IDENTIFIER    

adsl2Line 1.3.6.1.2.1.10.1.1.1
OBJECT IDENTIFIER    

adsl2Status 1.3.6.1.2.1.10.1.1.2
OBJECT IDENTIFIER    

adsl2Inventory 1.3.6.1.2.1.10.1.1.3
OBJECT IDENTIFIER    

adsl2PM 1.3.6.1.2.1.10.1.1.4
OBJECT IDENTIFIER    

adsl2Profile 1.3.6.1.2.1.10.1.1.5
OBJECT IDENTIFIER    

adsl2Scalar 1.3.6.1.2.1.10.1.1.6
OBJECT IDENTIFIER    

adsl2Notifications 1.3.6.1.2.1.10.1.1.0
OBJECT IDENTIFIER    

adsl2Conformance 1.3.6.1.2.1.10.1.1.8
OBJECT IDENTIFIER    

adsl2PMLine 1.3.6.1.2.1.10.1.1.4.1
OBJECT IDENTIFIER    

adsl2PMChannel 1.3.6.1.2.1.10.1.1.4.2
OBJECT IDENTIFIER    

adsl2ProfileLine 1.3.6.1.2.1.10.1.1.5.1
OBJECT IDENTIFIER    

adsl2ProfileChannel 1.3.6.1.2.1.10.1.1.5.2
OBJECT IDENTIFIER    

adsl2ProfileAlarmConf 1.3.6.1.2.1.10.1.1.5.3
OBJECT IDENTIFIER    

adsl2ScalarSC 1.3.6.1.2.1.10.1.1.6.1
OBJECT IDENTIFIER    

adsl2LineTable 1.3.6.1.2.1.10.1.1.1.1
The table adsl2LineTable contains configuration, command and status parameters of the ADSL2 line. The index of this table is an interface index where the interface has an ifType of adsl2(230).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Adsl2LineEntry

adsl2LineEntry 1.3.6.1.2.1.10.1.1.1.1.1
The table adsl2LineTable contains configuration, commands and status parameters of the ADSL2 line
Status: current Access: not-accessible
OBJECT-TYPE    
  Adsl2LineEntry  

adsl2LineCnfgTemplate 1.3.6.1.2.1.10.1.1.1.1.1.1
The value of this object identifies the row in the ADSL2 Line Configuration Templates Table, (Adsl2ConfTemplatesTable), which applies for this ADSL2 line.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString Size(1..32)  

adsl2LineAlarmCnfgTemplate 1.3.6.1.2.1.10.1.1.1.1.1.2
The value of this object identifies the row in the ADSL2 Line Alarm Configuration Template Table, (adsl2LineAlarmConfTemplateTable), which applies to this ADSL2 line.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString Size(1..32)  

adsl2LineCmndConfPmsf 1.3.6.1.2.1.10.1.1.1.1.1.3
Power management state forced. Defines the line states to be forced by the near-end ATU on this line. The various possible values are: l3toL0 (0), l0toL2 (2), l0orL2toL3 (3).
Status: current Access: read-write
OBJECT-TYPE    
  Adsl2ConfPmsForce  

adsl2LineCmndConfLdsf 1.3.6.1.2.1.10.1.1.1.1.1.4
Loop diagnostics mode forced (LDSF). Defines whether the line should be forced into the loop diagnostics mode by the near-end ATU on this line or only be responsive to loop diagnostics initiated by the far-end ATU.
Status: current Access: read-write
OBJECT-TYPE    
  Adsl2LineLdsf  

adsl2LineCmndConfLdsfFailReason 1.3.6.1.2.1.10.1.1.1.1.1.5
The status of the recent occasion the Loop diagnostics mode forced (LDSF) was issued for the associated line. Possible values are: none (1) - The default value in case LDSF was never requested for the associated line. success (2) - The recent command completed successfully. inProgress (3) - The Loop Diagnostics process is in progress. unsupported (4) - The NE or the line card doesn't support LDSF. cannotRun (5) - The NE cannot initiate the command, due to a non specific reason. aborted (6) - The Loop Diagnostics process aborted. failed (7) - The Loop Diagnostics process failed. illegalMode (8) - The NE cannot initiate the command, due to the specific mode of the relevant line. adminUp (9) - The NE cannot initiate the command, as the relevant line is administratively 'Up'. tableFull (10)- The NE cannot initiate the command, due to reaching the maximum number of rows in the results table. noResources (11)- The NE cannot initiate the command, due to lack of internal memory resources.
Status: current Access: read-only
OBJECT-TYPE    
  Adsl2LdsfResult  

adsl2LineCmndAutomodeColdStart 1.3.6.1.2.1.10.1.1.1.1.1.6
Automode cold start forced. This parameter is defined in order to improve testing of the performance of ATUs supporting automode when it is enabled in the MIB. Change the value of this parameter to 'true' indicates a change in loop conditions applied to the devices under test. The ATUs shall reset any historical information used for automode and for shortening G.994.1 handshake and initialization. Automode is the case where multiple operation-modes are enabled through the adsl2LConfProfAtuTransSysEna object in the line configuration profile being used for the ADSL line, and where the selection of the actual operation-mode depends not only on the common capabilities of both ATUs (as exchanged in G.994.1), but also on achievable data rates under given loop conditions.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

adsl2LineStatusAtuTransSys 1.3.6.1.2.1.10.1.1.1.1.1.7
The ATU Transmission System (ATS) in use. It is coded in a bit-map representation with one bit set to '1' (the selected coding for the ADSL line). This parameter may be derived from the handshaking procedures defined in Recommendation G.994.1. A set of ADSL2 line transmission modes, with one bit per mode.
Status: current Access: read-only
OBJECT-TYPE    
  Adsl2TransmissionModeType  

adsl2LineStatusPwrMngState 1.3.6.1.2.1.10.1.1.1.1.1.8
The current power management state. One of four possible power management states: L0 - Synchronized and full transmission (i.e., Showtime), L1 - Low Power with reduced net data rate (G.992.2 only), L2 - Low Power with reduced net data rate (G.992.3 and G.992.4 only), L3 - No power The various possible values are:l0(0), l1(1), l2(2), l3(3).
Status: current Access: read-only
OBJECT-TYPE    
  Adsl2PowerMngState  

adsl2LineStatusInitResult 1.3.6.1.2.1.10.1.1.1.1.1.9
Indicates the result of the last full initialization performed on the line. It is an enumeration type with the following values: noFailure(0), configError(1), configNotFeasible(2), commFail(3), noPeerAtu(4), otherCause(5).
Status: current Access: read-only
OBJECT-TYPE    
  Adsl2InitResult  

adsl2LineStatusLastStateDs 1.3.6.1.2.1.10.1.1.1.1.1.10
The last successful transmitted initialization state in the downstream direction in the last full initialization performed on the line. States are per the specific ADSL type and are counted from 0 (if G.994.1 is used) or 1 (if G.994.1 is not used) up to Showtime.
Status: current Access: read-only
OBJECT-TYPE    
  Adsl2LastTransmittedState  

adsl2LineStatusLastStateUs 1.3.6.1.2.1.10.1.1.1.1.1.11
The last successful transmitted initialization state in the upstream direction in the last full initialization performed on the line. States are per the specific ADSL type and are counted from 0 (if G.994.1 is used) or 1 (if G.994.1 is not used) up to Showtime.
Status: current Access: read-only
OBJECT-TYPE    
  Adsl2LastTransmittedState  

adsl2LineStatusAtur 1.3.6.1.2.1.10.1.1.1.1.1.12
Indicates current state (existing failures) of the ATU-R. This is a bit-map of possible conditions. The various bit positions are: noFailure(0), lossOfFraming(1), lossOfSignal(2), lossOfPower(3), initFailure(4) - never active on ATU-R
Status: current Access: read-only
OBJECT-TYPE    
  Adsl2LineStatus  

adsl2LineStatusAtuc 1.3.6.1.2.1.10.1.1.1.1.1.13
Indicates current state (existing failures) of the ATU-C. This is a bit-map of possible conditions. The various bit positions are: noFailure(0), lossOfFraming(1), lossOfSignal(2), lossOfPower(3), initFailure(4)
Status: current Access: read-only
OBJECT-TYPE    
  Adsl2LineStatus  

adsl2LineStatusLnAttenDs 1.3.6.1.2.1.10.1.1.1.1.1.14
The measured difference in the total power transmitted by the ATU-C and the total power received by the ATU-R over all sub- carriers during diagnostics mode and initialization. It ranges from 0 to 1270 units of 0.1 dB (Physical values are 0 to 127 dB). A value of all 1's indicates the line attenuation is out of range to be represented.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2LineStatusLnAttenUs 1.3.6.1.2.1.10.1.1.1.1.1.15
The measured difference in the total power transmitted by the ATU-R and the total power received by the ATU-C over all sub- carriers during diagnostics mode and initialization. It ranges from 0 to 1270 units of 0.1 dB (Physical values are 0 to 127 dB). A value of all 1's indicates the line attenuation is out of range to be represented.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2LineStatusSigAttenDs 1.3.6.1.2.1.10.1.1.1.1.1.16
The measured difference in the total power transmitted by the ATU-C and the total power received by the ATU-R over all sub- carriers during Showtime. It ranges from 0 to 1270 units of 0.1 dB (Physical values are 0 to 127 dB). A value of all 1's indicates the line attenuation is out of range to be represented.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2LineStatusSigAttenUs 1.3.6.1.2.1.10.1.1.1.1.1.17
The measured difference in the total power transmitted by the ATU-R and the total power received by the ATU-C over all sub- carriers during Showtime. It ranges from 0 to 1270 units of 0.1 dB (Physical values are 0 to 127 dB). A value of all 1's indicates the line attenuation is out of range to be represented.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2LineStatusSnrMarginDs 1.3.6.1.2.1.10.1.1.1.1.1.18
Downstream SNR Margin is the maximum increase in dB of the noise power received at the ATU-R, such that the BER requirements are met for all downstream bearer channels. It ranges from -640 to 630 units of 0.1 dB (Physical values are -64 to 63 dB). A value of all 1's indicates the line attenuation is out of range to be represented.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

adsl2LineStatusSnrMarginUs 1.3.6.1.2.1.10.1.1.1.1.1.19
Upstream SNR Margin is the maximum increase in dB of the noise power received at the ATU-C, such that the BER requirements are met for all downstream bearer channels. It ranges from -640 to 630 units of 0.1 dB (Physical values are -64 to 63 dB). A value of all 1's indicates the line attenuation is out of range to be represented.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

adsl2LineStatusAttainableRateDs 1.3.6.1.2.1.10.1.1.1.1.1.20
Maximum Attainable Data Rate Downstream. The maximum downstream net data rate currently attainable by the ATU-C transmitter and the ATU-R receiver, coded in bit/s.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2LineStatusAttainableRateUs 1.3.6.1.2.1.10.1.1.1.1.1.21
Maximum Attainable Data Rate Upstream. The maximum upstream net data rate currently attainable by the ATU-R transmitter and the ATU-C receiver, coded in bit/s.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2LineStatusActPsdDs 1.3.6.1.2.1.10.1.1.1.1.1.22
Actual Power Spectrum Density (PSD) Downstream. The average downstream transmit PSD over the sub-carriers used for downstream. It ranges from -900 to 0 units of 0.1 dB (Physical values are -90 to 0 dBm/Hz). A value of all 1's indicates the measurement is out of range to be represented.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

adsl2LineStatusActPsdUs 1.3.6.1.2.1.10.1.1.1.1.1.23
Actual Power Spectrum Density (PSD) Upstream. The average upstream transmit PSD over the sub-carriers used for upstream. It ranges from -900 to 0 units of 0.1 dB (Physical values are -90 to 0 dBm/Hz). A value of all 1's indicates the measurement is out of range to be represented.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

adsl2LineStatusActAtpDs 1.3.6.1.2.1.10.1.1.1.1.1.24
Actual Aggregate Transmit Power Downstream. The total amount of transmit power delivered by the ATU-C at the U-C reference point, at the instant of measurement. It ranges from -310 to 310 units of 0.1 dB (Physical values are -31 to 31 dBm). A value of all 1's indicates the measurement is out of range to be represented.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

adsl2LineStatusActAtpUs 1.3.6.1.2.1.10.1.1.1.1.1.25
Actual Aggregate Transmit Power Upstream. The total amount of transmit power delivered by the ATU-R at the U-R reference point, at the instant of measurement. It ranges from -310 to 310 units of 0.1 dB (Physical values are -31 to 31 dBm). A value of all 1's indicates the measurement is out of range to be represented.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

adsl2ChannelStatusTable 1.3.6.1.2.1.10.1.1.2.1
The table adsl2ChannelStatusTable contains status parameters of ADSL2 channel.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Adsl2ChannelStatusEntry

adsl2ChannelStatusEntry 1.3.6.1.2.1.10.1.1.2.1.1
The table adsl2ChannelStatusTable contains status parameters of ADSL2 channel. The index of this table is an interface index where the interface has an ifType value that is applicable for a DSL channel and the termination unit.
Status: current Access: not-accessible
OBJECT-TYPE    
  Adsl2ChannelStatusEntry  

adsl2ChStatusUnit 1.3.6.1.2.1.10.1.1.2.1.1.1
The termination unit ATUC(1) or ATUR(2).
Status: current Access: not-accessible
OBJECT-TYPE    
  Adsl2Unit  

adsl2ChStatusChannelNum 1.3.6.1.2.1.10.1.1.2.1.1.2
Provides the bearer channel number associated with this row (i.e., the channel ifIndex). This enables determining the channel configuration profile and the channel thresholds profile applicable for this bearer channel.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2ChStatusActDataRate 1.3.6.1.2.1.10.1.1.2.1.1.3
The actual net data rate that the bearer channel is operating at, if in L0 power management state. In L1 or L2 states, it relates to the previous L0 state. The data rate is coded in bit/s.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..200000000  

adsl2ChStatusPrevDataRate 1.3.6.1.2.1.10.1.1.2.1.1.4
The previous net data rate that the bearer channel was operating at just before the latest rate change event. This could be a full or short initialization, fast retrain, DRA or power management transitions, excluding transitions between L0 state and L1 or L2 states. The data rate is coded in bit/s.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..200000000  

adsl2ChStatusActDelay 1.3.6.1.2.1.10.1.1.2.1.1.5
The actual one-way interleaving delay introduced by the PMS-TC in the direction of the bearer channel, if in L0 power management state. In L1 or L2 states, it relates to the previous L0 state. It is coded in ms (rounded to the nearest ms).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..8176  

adsl2ChStatusAtmStatus 1.3.6.1.2.1.10.1.1.2.1.1.6
Indicates current state (existing failures) of the ADSL channel in case its Data Path is ATM. This is a bit-map of possible conditions. The various bit positions are: noFailure(0), noCellDelineation(1), lossOfCellDelineation (2). In case the channel is not of ATM Data Path the object is set to '0'.
Status: current Access: read-only
OBJECT-TYPE    
  Adsl2ChAtmStatus  

adsl2ChStatusPtmStatus 1.3.6.1.2.1.10.1.1.2.1.1.7
Indicates current state (existing failures) of the ADSL channel in case its Data Path is PTM. This is a bit-map of possible conditions. The various bit positions are: noFailure(0), outOfSync (1). In case the channel is not of PTM Data Path the object is set to '0'.
Status: current Access: read-only
OBJECT-TYPE    
  Adsl2ChPtmStatus  

adsl2ScalarSCMaxInterfaces 1.3.6.1.2.1.10.1.1.6.1.1
This value determines the upper size of adsl2SCStatusTable. The maximum number of entries in adsl2SCStatusTable is equal to two times the value of this attribute.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2ScalarSCAvailInterfaces 1.3.6.1.2.1.10.1.1.6.1.2
This value determines the amount of space that is currently available in adsl2SCStatusTable. The number of entries available in adsl2SCStatusTable is equal to two times the value of this attribute.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2SCStatusTable 1.3.6.1.2.1.10.1.1.2.2
The table adsl2SCStatusTable contains status parameters of ADSL2 sub-carriers.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Adsl2SCStatusEntry

adsl2SCStatusEntry 1.3.6.1.2.1.10.1.1.2.2.1
The table Hfadsl2SCStatusEntry contains status parameters of ADSL2 sub-carriers. The index of this table is an interface index where the interface has an ifType of adsl2(230).
Status: current Access: not-accessible
OBJECT-TYPE    
  Adsl2SCStatusEntry  

adsl2SCStatusDirection 1.3.6.1.2.1.10.1.1.2.2.1.1
The direction of the sub-carrier either upstream or downstream
Status: current Access: not-accessible
OBJECT-TYPE    
  Adsl2Direction  

adsl2SCStatusMtime 1.3.6.1.2.1.10.1.1.2.2.1.2
SNR Measurement Time. The number of symbols used to measure the SNR values on the respective transmission direction. It should correspond to the value specified in the recommendation (e.g., the number of symbols in 1 second time interval for G.992.3). This parameter corresponds to 1 second in loop diagnostic procedure and should be updated otherwise
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2SCStatusSnr 1.3.6.1.2.1.10.1.1.2.2.1.3
The SNR Margin per sub-carrier, expressing the ratio between the received signal power and received noise power per subscriber. It is an array of 512 bytes, designed for supporting up to 512 (downstream) sub-carriers. The number of utilized octets on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred here as NSC. Byte i (0 <= i < NSC) is set to a value in the range 0 to 254 to indicate that the respective downstream or upstream sub- carrier i has SNR of: (-32 + Adsl2SubcarrierSnr(i)/2) in dB (i.e., -32 to 95dB). The special value 255 means that no measurement could be done for the subcarrier because it is out of the PSD mask passband or that the noise PSD is out of range to be represented. Each value in this array is 8 bits wide.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..512)  

adsl2SCStatusBitsAlloc 1.3.6.1.2.1.10.1.1.2.2.1.4
The bits allocation per sub-carrier. An array of 256 bytes (512 nibbles), designed for supporting up to 512 (downstream) sub-carriers. The number of utilized nibbles on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred here as NSC. Nibble i (0 <= i < NSC) is set to a value in the range 0 to 15 to indicate that the respective downstream or upstream sub-carrier i has the same amount of bits allocation.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..256)  

adsl2SCStatusGainAlloc 1.3.6.1.2.1.10.1.1.2.2.1.5
The gain allocation per sub-carrier. An array of 512 16-bits values, designed for supporting up to 512 (downstream) sub- carriers. The number of utilized octets on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred here as NSC. Value i (0 <= i < NSC) is in the range 0 to 4093 to indicate that the respective downstream or upstream sub-carrier i has the same amount of gain value. The gain value is represented as a multiple of 1/512 on linear scale. Each value in this array is 16 bits wide and is stored in big endian format.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..1024)  

adsl2SCStatusTssi 1.3.6.1.2.1.10.1.1.2.2.1.6
The transmit spectrum shaping (TSSi) breakpoints expressed as the set of breakpoints exchanged during G.994.1. Each breakpoint is a pair of values occupying 3 octets with the following structure: First 2 octets - Index of the subcarrier used in the context of the breakpoint. Third octet - The shaping parameter at the breakpoint. Subcarrier index is an unsigned number in the range 1 to either NSCds (downstream direction) or NSCus (upstream direction). The shaping parameter value is in the range 0 to 127 (units of -0.5dB). The special value 127 indicates that the subcarrier is not transmitted.
Status: current Access: read-only
OBJECT-TYPE    
  Adsl2Tssi  

adsl2SCStatusLinScale 1.3.6.1.2.1.10.1.1.2.2.1.7
The scale factor to be applied to the H(f) linear representation values for the respective transmission direction. This parameter is only available after a loop diagnostic procedure.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2SCStatusLinReal 1.3.6.1.2.1.10.1.1.2.2.1.8
An array of up to 512 complex H(f) linear representation values in linear scale for the respective transmission direction. It is designed to support up to 512 (downstream) sub-carriers. The number of utilized values on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred here as NSC. Each array entry represents the real component [referred here as a(i)] of Hlin(f = i*Df) value for a particular sub-carrier index i (0 <= i < NSC). Hlin(f) is represented as ((scale/2^15)*((a(i)+j*b(i))/2^15)), where scale is Adsl2SubcarrierLinScale and a(i) and b(i) [provided by the Adsl2SubcarrierLinImg object] are in the range (-2^15+1) to (+2^15-1). A special value a(i)=b(i)= -2^15 indicates that no measurement could be done for the subcarrier because it is out of the passband or that the attenuation is out of range to be represented. This parameter is only available after a loop diagnostic procedure. Each value in this array is 16 bits wide and is stored in big endian format.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..1024)  

adsl2SCStatusLinImg 1.3.6.1.2.1.10.1.1.2.2.1.9
An array of up to 512 complex H(f) linear representation values in linear scale for the respective transmission direction. It is designed to support up to 512 (downstream) sub-carriers. The number of utilized values on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred here as NSC. Each array entry represents the imaginary component [referred here as b(i)] of Hlin(f = i*Df) value for a particular sub- carrier index i (0 <= i < NSC). Hlin(f) is represented as ((scale/2^15)*((a(i)+j*b(i))/2^15)), where scale is Adsl2SubcarrierLinScale and a(i) [provided by the Adsl2SubcarrierLinReal object] and b(i) are in the range (-2^15+1) to (+2^15-1). A special value a(i)=b(i)= -2^15 indicates that no measurement could be done for the subcarrier because it is out of the passband or that the attenuation is out of range to be represented. This parameter is only available after a loop diagnostic procedure. Each value in this array is 16 bits wide and is stored in big endian format.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..1024)  

adsl2SCStatusLogMt 1.3.6.1.2.1.10.1.1.2.2.1.10
The number of symbols used to measure the H(f) logarithmic measurement values for the respective transmission direction. This parameter should correspond to the value specified in the recommendation (e.g., the number of symbols in 1 second time interval for G.992.3). This parameter corresponds to 1 second in loop diagnostic procedure and should be updated in initialization
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2SCStatusLog 1.3.6.1.2.1.10.1.1.2.2.1.11
An array of up to 512 real H(f) logarithmic representation values in dB for the respective transmission direction. It is designed to support up to 512 (downstream) sub-carriers The number of utilized values on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred here as NSC. Each array entry represents the real Hlog(f = i*Df) value for a particular sub-carrier index i, (0 <= i < NSC). The real Hlog(f) value is represented as (6-m(i)/10), with m(i) in the range 0 to 1022. A special value m=1023 indicates that no measurement could be done for the subcarrier because it is out of the passband or that the attenuation is out of range to be represented. This parameter is applicable in loop diagnostic procedure and initialization. Each value in this array is 16 bits wide and is stored in big endian format.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..1024)  

adsl2SCStatusQlnMt 1.3.6.1.2.1.10.1.1.2.2.1.12
The number of symbols used to measure the Quiet Line Noise values on the respective transmission direction. This parameter should correspond to the value specified in the recommendation (e.g., the number of symbols in 1 second time interval for G.992.3). This parameter corresponds to 1 second in loop diagnostic procedure and should be updated in initialization
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2SCStatusQln 1.3.6.1.2.1.10.1.1.2.2.1.13
An array of up to 512 real Quiet Line Noise values in dBm/Hz for the respective transmission direction. It is designed for up to 512 (downstream) sub-carriers The number of utilized values on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred here as NSC. Each array entry represents the QLN(f = i*Df) value for a particular sub-carrier index i, (0 <= i < NSC). The QLN(f) is represented as ( -23-n(i)/2), with n(i) in the range 0 to 254. A special value n(i)=255 indicates that no measurement could be done for the subcarrier because it is out of the passband or that the noise PSD is out of range to be represented. This parameter is applicable in loop diagnostic procedure and initialization. Each value in this array is 8 bits wide.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..512)  

adsl2SCStatusLnAtten 1.3.6.1.2.1.10.1.1.2.2.1.14
When referring to the downstream direction, it is the measured difference in the total power transmitted by the ATU-C and the total power received by the ATU-R over all sub-carriers during diagnostics mode. When referring to the upstream direction, it is the measured difference in the total power transmitted by the ATU-R and the total power received by the ATU-C over all sub-carriers during diagnostics mode. It ranges from 0 to 1270 units of 0.1 dB (Physical values are 0 to 127 dB). A value of all 1's indicates the line attenuation is out of range to be represented. This object reflects the value of the parameter following the most recent DELT performed on the associated line. Once the DELT process is over, the parameter no longer changes until the row is deleted or a new DELT process is initiated.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2SCStatusSigAtten 1.3.6.1.2.1.10.1.1.2.2.1.15
When referring to the downstream direction, it is the measured difference in the total power transmitted by the ATU-C and the total power received by the ATU-R over all sub carriers during Showtime after the diagnostics mode. When referring to the upstream direction, it is the measured difference in the total power transmitted by the ATU-R and the total power received by the ATU-C over all sub carriers during Showtime after the diagnostics mode. It ranges from 0 to 1270 units of 0.1 dB (Physical values are 0 to 127 dB). A value of all 1's indicates the line attenuation is out of range to be represented. This object reflects the value of the parameter following the most recent DELT performed on the associated line. Once the DELT process is over, the parameter no longer changes until the row is deleted or a new DELT process is initiated.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2SCStatusSnrMargin 1.3.6.1.2.1.10.1.1.2.2.1.16
SNR Margin is the maximum increase in dB of the noise power received at the ATU (ATU-R on downstream direction and ATU-C on upstream direction), such that the BER requirements are met for all bearer channels received at the ATU. It ranges from -640 to 630 units of 0.1 dB (Physical values are -64 to 63 dB). A value of all 1's indicates the SNR margin is out of range to be represented. This object reflects the value of the parameter following the most recent DELT performed on the associated line. Once the DELT process is over, the parameter no longer changes until the row is deleted or a new DELT process is initiated.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

adsl2SCStatusAttainableRate 1.3.6.1.2.1.10.1.1.2.2.1.17
Maximum Attainable Data Rate. The maximum net data rate currently attainable by the ATU-C transmitter and ATU-R receiver (when referring to downstream direction) or by the ATU-R transmitter and ATU-C receiver (when referring to upstream direction). Value is coded in bits/s. This object reflects the value of the parameter following the most recent DELT performed on the associated line. Once the DELT process is over, the parameter no longer changes until the row is deleted or a new DELT process is initiated.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2SCStatusActAtp 1.3.6.1.2.1.10.1.1.2.2.1.18
Actual Aggregate Transmit Power from the ATU (ATU-R on downstream direction and ATU-C on upstream direction), at the instant of measurement. It ranges from -310 to 310 units of 0.1 dB (Physical values are -31 to 31 dBm). A value of all 1's indicates the measurement is out of range to be represented. This object reflects the value of the parameter following the most recent DELT performed on the associated line. Once the DELT process is over, the parameter no longer changes until the row is deleted or a new DELT process is initiated.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

adsl2SCStatusRowStatus 1.3.6.1.2.1.10.1.1.2.2.1.19
Row Status. The SNMP agent should create a row in this table for storing the results of a DELT performed on the associated line, if such a row does not already exist. The SNMP agent may have limited resources; therefore, if multiple rows co-exist in the table, it may fail to add new rows to the table or allocate memory resources for a new DELT process. If that occurs, the SNMP agent responds with either the value 'tableFull' or the value 'noResources' (for adsl2LineCmndConfLdsfFailReason object in adsl2LineTable) The management system (the operator) may delete rows according to any scheme. E.g., after retrieving the results.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

adsl2LineInventoryTable 1.3.6.1.2.1.10.1.1.3.1
The table adsl2LineInventoryTable contains inventory of ADSL2 unit.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Adsl2LineInventoryEntry

adsl2LineInventoryEntry 1.3.6.1.2.1.10.1.1.3.1.1
The table adsl2LineInventoryTable contains inventory of ADSL2 unit. The index of this table is an interface index where the interface has an ifType of adsl2(230).
Status: current Access: not-accessible
OBJECT-TYPE    
  Adsl2LineInventoryEntry  

adsl2LInvUnit 1.3.6.1.2.1.10.1.1.3.1.1.1
The termination unit ATUC{1} or ATUR{2}.
Status: current Access: not-accessible
OBJECT-TYPE    
  Adsl2Unit  

adsl2LInvG994VendorId 1.3.6.1.2.1.10.1.1.3.1.1.2
The ATU G.994.1 Vendor ID as inserted in the G.994.1 CL/CLR message. It consists of 8 binary octets, including a country code followed by a (regionally allocated) provider code, as defined in Recommendation T.35.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..8)  

adsl2LInvSystemVendorId 1.3.6.1.2.1.10.1.1.3.1.1.3
The ATU System Vendor ID (identifies the ATU system integrator) as inserted in the Overhead Messages (both ATUs for G.992.3 and G.992.4) or in the Embedded Operations Channel (only ATU-R in G.992.1 and G.992.2). It consists of 8 binary octets, with same format as used for Adsl2InvG994VendorId.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..8)  

adsl2LInvVersionNumber 1.3.6.1.2.1.10.1.1.3.1.1.4
The ATU version number (vendor specific information) as inserted in the Overhead Messages (both ATUs for G.992.3 and G.992.4) or in the Embedded Operations Channel (only ATU-R in G.992.1 and G.992.2). It consists of up to 16 binary octets.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

adsl2LInvSerialNumber 1.3.6.1.2.1.10.1.1.3.1.1.5
The ATU serial number (vendor specific information) as inserted in the Overhead Messages (both ATUs for G.992.3 and G.992.4) or in the Embedded Operations Channel (only ATU-R in G.992.1 and G.992.2). It is vendor specific information. It consists of up to 32 ASCII characters.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

adsl2LInvSelfTestResult 1.3.6.1.2.1.10.1.1.3.1.1.6
The ATU self-test result, coded as a 32-bit integer. The most significant octet of this object is '0' if the self-test passed, and '1' if the self-test failed. The interpretation of the other octets is vendor discretionary.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..4)  

adsl2LInvTransmissionCapabilities 1.3.6.1.2.1.10.1.1.3.1.1.7
The ATU transmission system capability list of the different coding types. It is coded in a bit-map representation with 1 or more bits set. A bit set to '1' means that the ATU supports the respective coding. The value may be derived from the handshaking procedures defined in G.994.1. A set of ADSL2 line transmission modes, with one bit per mode.
Status: current Access: read-only
OBJECT-TYPE    
  Adsl2TransmissionModeType  

adsl2LineConfTemplateTable 1.3.6.1.2.1.10.1.1.5.1.1
The table adsl2LineConfTemplateTable contains ADSL2 line configuration template.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Adsl2LineConfTemplateEntry

adsl2LineConfTemplateEntry 1.3.6.1.2.1.10.1.1.5.1.1.1
The table adsl2LineConfTemplateTable contains ADSL2 line configuration template. A default template with an index of 'DEFVAL' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document
Status: current Access: not-accessible
OBJECT-TYPE    
  Adsl2LineConfTemplateEntry  

adsl2LConfTempTemplateName 1.3.6.1.2.1.10.1.1.5.1.1.1.1
This object identifies a row in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SnmpAdminString Size(1..32)  

adsl2LConfTempLineProfile 1.3.6.1.2.1.10.1.1.5.1.1.1.2
The value of this object identifies the row in the ADSL2 Line Configuration Profile Table, (Adsl2LineConfProfileTable), which applies for this ADSL2 line.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString Size(1..32)  

adsl2LConfTempChan1ConfProfile 1.3.6.1.2.1.10.1.1.5.1.1.1.3
The value of this object identifies the row in the ADSL2 Channel Configuration Profile Table, (Adsl2ChanConfProfileTable) that applies to ADSL2 bearer channel #1. The channel profile name specified here must match the name of an existing row in the adsl2ChConfProfileTable table.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString Size(1..32)  

adsl2LConfTempChan1RaRatioDs 1.3.6.1.2.1.10.1.1.5.1.1.1.4
Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #1 when performing rate adaptation on Downstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - Adsl2ConfTemplateChan1RaRatioDs is the ratio of excess data rate to be assigned to all other bearer channels on Downstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..100  

adsl2LConfTempChan1RaRatioUs 1.3.6.1.2.1.10.1.1.5.1.1.1.5
Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #1 when performing rate adaptation on Upstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - Adsl2ConfTemplateChan1RaRatioUs is the ratio of excess data rate to be assigned to all other bearer channels on Upstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100 %.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..100  

adsl2LConfTempChan2ConfProfile 1.3.6.1.2.1.10.1.1.5.1.1.1.6
The value of this object identifies the row in the ADSL2 Channel Configuration Profile Table, (Adsl2ChanConfProfileTable) that applies to ADSL2 bearer channel #2. If the channel is unused, then the object is set to a zero length string. This object may be set to a zero length string only if adsl2LConfTempChan3ConfProfile contains a zero length string.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString Size(0..32)  

adsl2LConfTempChan2RaRatioDs 1.3.6.1.2.1.10.1.1.5.1.1.1.7
Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #2 when performing rate adaptation on Downstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - Adsl2ConfTemplateChan2RaRatioDs is the ratio of excess data rate to be assigned to all other bearer channels on Downstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..100  

adsl2LConfTempChan2RaRatioUs 1.3.6.1.2.1.10.1.1.5.1.1.1.8
Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #2 when performing rate adaptation on Upstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - Adsl2ConfTemplateChan2RaRatioUs is the ratio of excess data rate to be assigned to all other bearer channels on Upstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100 %.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..100  

adsl2LConfTempChan3ConfProfile 1.3.6.1.2.1.10.1.1.5.1.1.1.9
The value of this object identifies the row in the ADSL2 Channel Configuration Profile Table, (Adsl2ChanConfProfileTable) that applies to ADSL2 bearer channel #3. If the channel is unused, then the object is set to a zero length string. This object may be set to a zero length string only if adsl2LConfTempChan4ConfProfile contains a zero length string. This object may be set to a non-zero length string only if adsl2LConfTempChan2ConfProfile contains a non-zero length string.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString Size(0..32)  

adsl2LConfTempChan3RaRatioDs 1.3.6.1.2.1.10.1.1.5.1.1.1.10
Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #3 when performing rate adaptation on Downstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - Adsl2ConfTemplateChan3RaRatioDs is the ratio of excess data rate to be assigned to all other bearer channels on Downstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..100  

adsl2LConfTempChan3RaRatioUs 1.3.6.1.2.1.10.1.1.5.1.1.1.11
Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #3 when performing rate adaptation on Upstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - Adsl2ConfTemplateChan3RaRatioUs is the ratio of excess data rate to be assigned to all other bearer channels on Upstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..100  

adsl2LConfTempChan4ConfProfile 1.3.6.1.2.1.10.1.1.5.1.1.1.12
The value of this object identifies the row in the ADSL2 Channel Configuration Profile Table (Adsl2ChanConfProfileTableDs) that applies to ADSL2 bearer channel #4. If the channel is unused, then the object is set to a zero length string. This object may be set to a non-zero length string only if adsl2LConfTempChan3ConfProfile contains a non-zero length string.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString Size(0..32)  

adsl2LConfTempChan4RaRatioDs 1.3.6.1.2.1.10.1.1.5.1.1.1.13
Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #4 when performing rate adaptation on Downstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - adsl2LConfTempChan4RaRatioDs is the ratio of excess data rate to be assigned to all other bearer channels. The sum of rate adaptation ratios over all bearers on the same direction shall sum to 100%.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..100  

adsl2LConfTempChan4RaRatioUs 1.3.6.1.2.1.10.1.1.5.1.1.1.14
Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #4 when performing rate adaptation on Upstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - adsl2LConfTempChan4RaRatioUs is the ratio of excess data rate to be assigned to all other bearer channels. The sum of rate adaptation ratios over all bearers on the same direction shall sum to 100%.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..100  

adsl2LConfTempRowStatus 1.3.6.1.2.1.10.1.1.5.1.1.1.15
This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'outOfService'), it must be first unreferenced from all associated lines.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

adsl2LineConfProfTable 1.3.6.1.2.1.10.1.1.5.1.2
The table adsl2LineConfProfTable contains ADSL2 line profile configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Adsl2LineConfProfEntry

adsl2LineConfProfEntry 1.3.6.1.2.1.10.1.1.5.1.2.1
The table adsl2LineConfProfTable contains ADSL2 line profile configuration. A default profile with an index of 'DEFVAL' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document
Status: current Access: not-accessible
OBJECT-TYPE    
  Adsl2LineConfProfEntry  

adsl2LConfProfProfileName 1.3.6.1.2.1.10.1.1.5.1.2.1.1
This object identifies a row in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SnmpAdminString Size(1..32)  

adsl2LConfProfScMaskDs 1.3.6.1.2.1.10.1.1.5.1.2.1.2
Sub-carriers mask. A bitmap of 512 bits that allows masking up to 512 downstream sub-carriers, depending on NSCds. If bit i (0 <= i < NSCds) is set to '1', the respective downstream sub-carrier i is masked, and if set to '0', the respective sub-carrier is unmasked. Note that there should always be unmasked sub-carriers (i.e., the object cannot be all 1's). Also note that if NSCds < 512, all bits i (NSCds i <= 512) should be set to '1'.
Status: current Access: read-create
OBJECT-TYPE    
  Adsl2ScMaskDs  

adsl2LConfProfScMaskUs 1.3.6.1.2.1.10.1.1.5.1.2.1.3
Sub-carriers mask. A bitmap of 64 bits that allows masking up to 64 downstream sub-carriers, depending on NSCds. If bit i (0 <= i < NSCus) is set to '1', the respective upstream sub-carrier i is masked, and if set to '0', the respective sub-carrier is unmasked. Note that there should always be unmasked sub-carriers (i.e., the object cannot be all 1's). Also note that if NSCus < 64, all bits i (NSCus < i <= 64) should be set to '1'.
Status: current Access: read-create
OBJECT-TYPE    
  Adsl2ScMaskUs  

adsl2LConfProfRfiBandsDs 1.3.6.1.2.1.10.1.1.5.1.2.1.4
The subset of downstream PSD mask breakpoints that shall be used to notch an RFI band. The specific interpolation around these points is defined in G.992.5. It is a bitmap of 512 bits that allows referring to up to 512 downstream sub-carriers, depending on NSCds. If bit i (0 <= i < NSCds) is set to '1', the respective downstream sub-carrier i is part of a notch filter, and if set to '0', the respective sub-carrier is not part of a notch filter. This information complements the specification provided by adsl2LconfProfPsdMaskDs. Note that if NSCds < 512, all bits i (NSCds
Status: current Access: read-create
OBJECT-TYPE    
  Adsl2RfiDs  

adsl2LConfProfRaModeDs 1.3.6.1.2.1.10.1.1.5.1.2.1.5
The mode of operation of a rate-adaptive ATU-C in the transmit direction. The parameter can take three values: manual (1), raInit (2), dynamicRa (3).
Status: current Access: read-create
OBJECT-TYPE    
  Adsl2RaMode  

adsl2LConfProfRaModeUs 1.3.6.1.2.1.10.1.1.5.1.2.1.6
The mode of operation of a rate-adaptive ATU-R in the transmit direction. The parameter can take three values: manual (1), raInit (2), dynamicRa (3).
Status: current Access: read-create
OBJECT-TYPE    
  Adsl2RaMode  

adsl2LConfProfRaUsNrmDs 1.3.6.1.2.1.10.1.1.5.1.2.1.7
The Downstream Up-Shift Noise Margin value, to be used when Adsl2LineConfRaModeDs is set to DynamicRa. If the downstream noise margin is above this value and stays above it for more than the time specified by the Adsl2LineConfRaUsTimeDs, the ATU-R shall attempt to increase the downstream net data rate. The Downstream Up-shift Noise Margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB).
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..310  

adsl2LConfProfRaUsNrmUs 1.3.6.1.2.1.10.1.1.5.1.2.1.8
The Upstream Up-Shift Noise Margin value, to be used when Adsl2LineConfRaModeUs is set to DynamicRa. If the upstream noise margin is above this value and stays above it for more than the time specified by the Adsl2LineConfRaUsTimeUs, the ATU-C shall attempt to increase the upstream net data rate. The Upstream Up-shift Noise Margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB).
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..310  

adsl2LConfProfRaUsTimeDs 1.3.6.1.2.1.10.1.1.5.1.2.1.9
The Downstream Up-Shift Time Interval, to be used when Adsl2LineConfRaModeDs is set to DynamicRa. The interval of time that the downstream noise margin should stay above the Downstream Up-shift Noise Margin before the ATU-R shall attempt to increase the downstream net data rate. The time interval ranges from 0 to 16383 seconds.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..16383  

adsl2LConfProfRaUsTimeUs 1.3.6.1.2.1.10.1.1.5.1.2.1.10
The Upstream Up-Shift Time Interval, to be used when Adsl2LineConfRaModeUs is set to DynamicRa. The interval of time the upstream noise margin should stay above the Upstream Up-shift Noise Margin before the ATU-C shall attempt to increase the upstream net data rate. The time interval ranges from 0 to 16383 seconds.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..16383  

adsl2LConfProfRaDsNrmsDs 1.3.6.1.2.1.10.1.1.5.1.2.1.11
The Downstream Down-Shift Noise Margin value, to be used when Adsl2LineConfRaModeDs is set to DynamicRa. If the downstream noise margin is below this value and stays below that for more than the time specified by the Adsl2LineConfRaDsTimeDs, the ATU-R shall attempt to decrease the downstream net data rate. The Downstream Down-shift Noise Margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB).
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..310  

adsl2LConfProfRaDsNrmsUs 1.3.6.1.2.1.10.1.1.5.1.2.1.12
The Upstream Downshift Noise Margin value, to be used when Adsl2LineConfRaModeUs is set to DynamicRa. If the upstream noise margin is below this value and stays below that for more than the time specified by the Adsl2LineConfRaDsTimeUs, the ATU-C shall attempt to decrease the upstream net data rate. The Upstream Down-shift Noise Margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB).
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..310  

adsl2LConfProfRaDsTimeDs 1.3.6.1.2.1.10.1.1.5.1.2.1.13
The Downstream Downshift Time Interval, to be used when Adsl2LineConfRaModeDs is set to DynamicRa. The interval of time the downstream noise margin should stay below the Downstream Down-shift Noise Margin before the ATU-R shall attempt to decrease the downstream net data rate. The time interval ranges from 0 to 16383 seconds.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..16383  

adsl2LConfProfRaDsTimeUs 1.3.6.1.2.1.10.1.1.5.1.2.1.14
The Upstream Down-Shift Time Interval, to be used when Adsl2LineConfRaModeUs is set to DynamicRa. The interval of time the upstream noise margin should stay below the Upstream Down-shift Noise Margin before the ATU-C shall attempt to decrease the upstream net data rate. The time interval ranges from 0 to 16383 seconds.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..16383  

adsl2LConfProfTargetSnrmDs 1.3.6.1.2.1.10.1.1.5.1.2.1.15
The minimum Noise Margin the ATU-R receiver shall achieve, relative to the BER requirement for each of the downstream bearer channels, to successfully complete initialization. The target noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB).
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..310  

adsl2LConfProfTargetSnrmUs 1.3.6.1.2.1.10.1.1.5.1.2.1.16
The minimum Noise Margin the ATU-C receiver shall achieve, relative to the BER requirement for each of the upstream bearer channels, to successfully complete initialization. The target noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB).
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..310  

adsl2LConfProfMaxSnrmDs 1.3.6.1.2.1.10.1.1.5.1.2.1.17
The maximum Noise Margin the ATU-R receiver shall try to sustain. If the Noise Margin is above this level, the ATU-R shall request that the ATU-C reduce the ATU-C transmit power to get a noise margin below this limit (if this functionality is supported). The maximum noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). A value of all 1's means that there is no maximum.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

adsl2LConfProfMaxSnrmUs 1.3.6.1.2.1.10.1.1.5.1.2.1.18
The maximum Noise Margin the ATU-C receiver shall try to sustain. If the Noise Margin is above this level, the ATU-C shall request that the ATU-R reduce the ATU-R transmit power to get a noise margin below this limit (if this functionality is supported). The maximum noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). A value of all 1's means that there is no maximum.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

adsl2LConfProfMinSnrmDs 1.3.6.1.2.1.10.1.1.5.1.2.1.19
The minimum Noise Margin the ATU-R receiver shall tolerate. If the noise margin falls below this level, the ATU-R shall request that the ATU-C increase the ATU-C transmit power. If an increase to ATU-C transmit power is not possible, a loss-of-margin (LOM) defect occurs, the ATU-R shall fail and attempt to reinitialize and the NMS shall be notified. The minimum noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). A value of 0 means that there is no minimum.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..310  

adsl2LConfProfMinSnrmUs 1.3.6.1.2.1.10.1.1.5.1.2.1.20
The minimum Noise Margin the ATU-C receiver shall tolerate. If the noise margin falls below this level, the ATU-C shall request that the ATU-R increase the ATU-R transmit power. If an increase of ATU-R transmit power is not possible, a loss-of-margin (LOM) defect occurs, the ATU-C shall fail and attempt to re-initialize and the NMS shall be notified. The minimum noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). A value of 0 means that there is no minimum.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..310  

adsl2LConfProfMsgMinUs 1.3.6.1.2.1.10.1.1.5.1.2.1.21
Minimum Overhead Rate Upstream. Defines the minimum rate of the message-based overhead that shall be maintained by the ATU in upstream direction. Expressed in bits per second and ranges from 4000 to 63000 bps.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 4000..63000  

adsl2LConfProfMsgMinDs 1.3.6.1.2.1.10.1.1.5.1.2.1.22
Minimum Overhead Rate Downstream. Defines the minimum rate of the message-based overhead that shall be maintained by the ATU in downstream direction. Expressed in bits per second and ranges from 4000 to 63000 bps.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 4000..63000  

adsl2LConfProfAtuTransSysEna 1.3.6.1.2.1.10.1.1.5.1.2.1.23
ATU Transmission System Enabling (ATSE). A list of the different coding types enabled in this profile. It is coded in a bit-map representation with 1 or more bits set. A bit set to '1' means that the ATUs may apply the respective coding for the ADSL line. A bit set to '0' means that the ATUs cannot apply the respective coding for the ADSL line. All 'reserved' bits should be set to '0'.
Status: current Access: read-create
OBJECT-TYPE    
  Adsl2TransmissionModeType  

adsl2LConfProfPmMode 0.1.1.3.6.1.2.1.10.1.1.5.1.2.1.24
Power management state Enabling. Defines the power states the ATU-C or ATU-R may autonomously transition to on this line. The various bit positions are: allowTransitionsToIdle (0) and allowTransitionsToLowPower (1). A bit with a '1' value means that the ATU is allowed to transit into the respective state and a '0' value means that the ATU is not allowed to transit into the respective state.
Status: current Access: read-create
OBJECT-TYPE    
  Adsl2LConfProfPmMode  

adsl2LConfProfL0Time 1.3.6.1.2.1.10.1.1.5.1.2.1.25
This minimum time (in seconds) between an Exit from the L2 state and the next Entry into the L2 state. It ranges from 0 to 255 seconds.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..255  

adsl2LConfProfL2Time 1.3.6.1.2.1.10.1.1.5.1.2.1.26
This minimum time (in seconds) between an Entry into the L2 state and the first Power Trim in the L2 state and between two consecutive Power Trims in the L2 State. It ranges from 0 to 255 seconds.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..255  

adsl2LConfProfL2Atpr 1.3.6.1.2.1.10.1.1.5.1.2.1.27
The maximum aggregate transmit power reduction (in dB) that can be performed at transition of L0 to L2 state or through a single Power Trim in the L2 state. It ranges from 0 dB to 31 dB.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..31  

adsl2LConfProfL2Atprt 1.3.6.1.2.1.10.1.1.5.1.2.1.28
The total maximum aggregate transmit power reduction (in dB) that can be performed in an L2 state. This is the sum of all reductions of L2 Request (i.e., at transition of L0 to L2 state) and Power Trims.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..31  

adsl2LConfProfRowStatus 1.3.6.1.2.1.10.1.1.5.1.2.1.29
This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'outOfService'), it must be first unreferenced from all associated templates.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

adsl2LineConfProfModeSpecTable 1.3.6.1.2.1.10.1.1.5.1.3
The table adsl2LineConfProfModeSpecTable extends the ADSL2 line configuration profile by ADSL Mode Specific parameters. A row in this table that has an index of adsl2LconfProfAdslMode == defMode(1), is called a 'mandatory' row. A row in this table that has an index such that adsl2LconfProfAdslMode is not equal to defMode(1), is called an 'optional' row. When a row in the adsl2LineConfProfTable table (the parent row) is created, the SNMP agent will automatically create a 'mandatory' row in this table. When the parent row is deleted, the SNMP agent will automatically delete all associated rows in this table. Any attempt to delete the 'mandatory' row using the adsl2LConfProfModeSpecRowStatus attribute will be rejected by the SNMP agent. The manager MAY create an 'optional' row in this table using the adsl2LConfProfModeSpecRowStatus attribute if the parent row exists. The manager MAY delete an 'optional' row in this table using the adsl2LConfProfModeSpecRowStatus attribute at any time. If the actual transmission mode of a DSL line does not match one of the 'optional' rows in this table, then the line will use the PSD configuration from the 'mandatory' row.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Adsl2LineConfProfModeSpecEntry

adsl2LineConfProfModeSpecEntry 1.3.6.1.2.1.10.1.1.5.1.3.1
The table adsl2LineConfProfModeSpecTable extends the ADSL2 line configuration profile by ADSL Mode Specific parameters.
Status: current Access: not-accessible
OBJECT-TYPE    
  Adsl2LineConfProfModeSpecEntry  

adsl2LconfProfAdslMode 1.3.6.1.2.1.10.1.1.5.1.3.1.1
The ADSL Mode is a way of categorizing the various ADSL transmission modes into groups, each group (ADSL Mode) shares the same PSD configuration. There should be multiple entries in this table for a given line profile in case multiple bits are set in adsl2LConfProfAtuTransSysEna for that profile.
Status: current Access: not-accessible
OBJECT-TYPE    
  Adsl2OperationModes  

adsl2LConfProfMaxNomPsdDs 1.3.6.1.2.1.10.1.1.5.1.3.1.2
The maximum nominal transmit PSD in the downstream direction during initialization and Showtime. It ranges from -600 to -300 units of 0.1 dBm/Hz. (physical values are -60 to -30 dBm/Hz).
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 -600..-300  

adsl2LConfProfMaxNomPsdUs 1.3.6.1.2.1.10.1.1.5.1.3.1.3
The maximum nominal transmit PSD in the upstream direction during initialization and Showtime. It ranges from -600 to -300 units of 0.1 dBm/Hz. (physical values are -60 to -30 dBm/Hz).
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 -600..-300  

adsl2LConfProfMaxNomAtpDs 1.3.6.1.2.1.10.1.1.5.1.3.1.4
The maximum nominal aggregate transmit power in the downstream direction during initialization and Showtime. It ranges from 0 to 255 units of 0.1 dBm (physical values are 0 to 25.5 dBm).
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..255  

adsl2LConfProfMaxNomAtpUs 1.3.6.1.2.1.10.1.1.5.1.3.1.5
The maximum nominal aggregate transmit power in the upstream direction during initialization and Showtime. It ranges from 0 to 255 units of 0.1 dBm (physical values are 0 to 25.5 dBm).
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..255  

adsl2LConfProfMaxAggRxPwrUs 1.3.6.1.2.1.10.1.1.5.1.3.1.6
The maximum upstream aggregate receive power over the relevant set of sub-carriers. The ATU-C should verify that the upstream power cutback is such that this maximum aggregate receive power value is honored. It ranges from -255 to 255 units of 0.1 dBm (physical values are -25.5 to 25.5 dBm). A value of all ones means that there is no limit.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 -255..2147483647  

adsl2LConfProfPsdMaskDs 1.3.6.1.2.1.10.1.1.5.1.3.1.7
The downstream PSD mask applicable at the U-C2 reference point. This parameter is used only for G.992.5 and it may impose PSD restrictions (breakpoints) in addition to the Limit PSD mask defined in G.992.5. This is a string of 32 pairs of values in the following structure: Octets 0+1 - Index of 1st sub-carrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1. Octets 3-5 - Same, for a 2nd breakpoint. Octets 6-8 - Same, for a 3rd breakpoint. This architecture continues until octets 94-95, which are associated with a 32nd breakpoint. Each subcarrier index is an unsigned number in the range 1 and NSCds. Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are in the range 0 to 190 (0 to -95dBm/Hz). When the number of breakpoints is less than 32, all remaining octets are set to the value 0. Note that the content of this object should be correlated with the sub-carriers mask and with the RFI setup.
Status: current Access: read-create
OBJECT-TYPE    
  Adsl2PsdMaskDs  

adsl2LConfProfPsdMaskUs 1.3.6.1.2.1.10.1.1.5.1.3.1.8
The upstream PSD mask applicable at the U-R2 reference point. This parameter is used only for G.992.5 and it may impose PSD restrictions (breakpoints) in addition to the Limit PSD mask defined in G.992.5. This is a string of 4 pairs of values in the following structure: Octets 0+1 - Index of 1st sub-carrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1. Octets 3-5 - Same, for a 2nd breakpoint. Octets 6-8 - Same, for a 3rd breakpoint. This architecture continues until octets 9-11, which are associated with a 4th breakpoint. Each subcarrier index is an unsigned number in the range 1 and NSCus. Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are in the range 0 to 190 (0 to -95dBm/Hz). When the number of breakpoints is less than 4, all remaining octets are set to the value 0. Note that the content of this object should be correlated with the sub-carriers mask and with the RFI setup.
Status: current Access: read-create
OBJECT-TYPE    
  Adsl2PsdMaskUs  

adsl2LConfProfPsdMaskSelectUs 1.3.6.1.2.1.10.1.1.5.1.3.1.9
The selected upstream PSD mask. This parameter is used only for annexes J and M of G.992.3 and G.992.5, and the same selection is used for all relevant enabled bits in adsl2LConfProfAtuTransSysEna.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 1..9  

adsl2LConfProfModeSpecRowStatus 1.3.6.1.2.1.10.1.1.5.1.3.1.10
This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'outOfService'), it must be first unreferenced from all associated templates.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

adsl2ChConfProfileTable 1.3.6.1.2.1.10.1.1.5.2.1
The table adsl2ChConfProfileTable contains ADSL2 channel profile configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Adsl2ChConfProfileEntry

adsl2ChConfProfileEntry 1.3.6.1.2.1.10.1.1.5.2.1.1
The table adsl2ChConfProfileTable contains ADSL2 channel profile configuration. A default profile with an index of 'DEFVAL' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document
Status: current Access: not-accessible
OBJECT-TYPE    
  Adsl2ChConfProfileEntry  

adsl2ChConfProfProfileName 1.3.6.1.2.1.10.1.1.5.2.1.1.1
This object identifies a row in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SnmpAdminString Size(1..32)  

adsl2ChConfProfMinDataRateDs 1.3.6.1.2.1.10.1.1.5.2.1.1.2
Minimum Data Rate on Downstream direction. The minimum net data rate for the bearer channel, coded in bit/s.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..200000000  

adsl2ChConfProfMinDataRateUs 1.3.6.1.2.1.10.1.1.5.2.1.1.3
Minimum Data Rate on Upstream direction. The minimum net data rate for the bearer channel, coded in bit/s.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..200000000  

adsl2ChConfProfMinResDataRateDs 1.3.6.1.2.1.10.1.1.5.2.1.1.4
Minimum Reserved Data Rate on Downstream direction. The minimum reserved net data rate for the bearer channel, coded in bit/s. This parameter is used only if the Rate Adaptation Mode in the direction of the bearer channel (i.e., Adsl2LineConfRaModeDs) is set to DynamicRa.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..200000000  

adsl2ChConfProfMinResDataRateUs 1.3.6.1.2.1.10.1.1.5.2.1.1.5
Minimum Reserved Data Rate on Upstream direction. The minimum reserved net data rate for the bearer channel, coded in bit/s. This parameter is used only if the Rate Adaptation Mode in the direction of the bearer channel (i.e., Adsl2LineConfRaModeUs) is set to DynamicRa.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..200000000  

adsl2ChConfProfMaxDataRateDs 1.3.6.1.2.1.10.1.1.5.2.1.1.6
Maximum Data Rate on Downstream direction. The maximum net data rate for the bearer channel, coded in bit/s.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..200000000  

adsl2ChConfProfMaxDataRateUs 1.3.6.1.2.1.10.1.1.5.2.1.1.7
Maximum Data Rate on Upstream direction. The maximum net data rate for the bearer channel, coded in bit/s.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..200000000  

adsl2ChConfProfMinDataRateLowPwrDs 1.3.6.1.2.1.10.1.1.5.2.1.1.8
Minimum Data Rate in Low Power state on Downstream direction. The minimum net data rate for the bearer channel, coded in bit/s., during the low power state (L1 in G.992.2, L2 in G.992.3).
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..200000000  

adsl2ChConfProfMinDataRateLowPwrUs 1.3.6.1.2.1.10.1.1.5.2.1.1.9
Minimum Data Rate in Low Power state on Upstream direction. The minimum net data rate for the bearer channel, coded in bit/s., during the low power state (L1 in G.992.2, L2 in G.992.3).
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..200000000  

adsl2ChConfProfMaxDelayDs 1.3.6.1.2.1.10.1.1.5.2.1.1.10
Maximum Interleave Delay on Downstream direction. The maximum one-way interleaving delay introduced by the PMS-TC on Downstream direction. The ATUs shall choose the S (factor) and D (depth) values such that the actual one-way interleaving delay (Adsl2ChanStatusActDelay) is as close as possible to, but less than or equal to, Adsl2ChanConfMaxDelayDs. The delay is coded in ms, with the value 0 indicating no delay bound is being imposed.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..63  

adsl2ChConfProfMaxDelayUs 1.3.6.1.2.1.10.1.1.5.2.1.1.11
Maximum Interleave Delay on Upstream direction. The maximum one-way interleaving delay introduced by the PMS-TC on Upstream direction. The ATUs shall choose the S (factor) and D (depth) values such that the actual one-way interleaving delay (Adsl2ChanStatusActDelay) is as close as possible to, but less than or equal to, Adsl2ChanConfMaxDelayUs. The delay is coded in ms, with the value 0 indicating no delay bound is being imposed.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..63  

adsl2ChConfProfMinProtectionDs 1.3.6.1.2.1.10.1.1.5.2.1.1.12
Minimum Impulse Noise Protection on Downstream direction. The minimum impulse noise protection for the bearer channel, expressed in symbols. The parameter can take the following values: noProtection (i.e., INP not required), halfSymbol (i.e., INP length is 1/2 symbol) and 1-16 symbols in steps of 1 symbol.
Status: current Access: read-create
OBJECT-TYPE    
  Adsl2SymbolProtection  

adsl2ChConfProfMinProtectionUs 1.3.6.1.2.1.10.1.1.5.2.1.1.13
Minimum Impulse Noise Protection on Upstream direction. The minimum impulse noise protection for the bearer channel, expressed in symbols. The parameter can take the following values: noProtection (1), halfSymbol (2), singleSymbol (3), twoSymbols (4), fourSymbols (5), eightSymbols (6), sixteenSymbols (7).
Status: current Access: read-create
OBJECT-TYPE    
  Adsl2SymbolProtection  

adsl2ChConfProfMaxBerDs 1.3.6.1.2.1.10.1.1.5.2.1.1.14
Maximum Bit Error Ratio on Downstream direction. The maximum bit error ratio for the bearer channel. The parameter can take the following values (for 1E-3, 1E-5 or 1E-7): eminus3 (1), eminus5 (2), eminus7 (3)
Status: current Access: read-create
OBJECT-TYPE    
  Adsl2MaxBer  

adsl2ChConfProfMaxBerUs 1.3.6.1.2.1.10.1.1.5.2.1.1.15
Maximum Bit Error Ratio on Upstream direction. The maximum bit error ratio for the bearer channel. The parameter can take the following values (for 1E-3, 1E-5 or 1E-7): eminus3 (1), eminus5 (2), eminus7 (3)
Status: current Access: read-create
OBJECT-TYPE    
  Adsl2MaxBer  

adsl2ChConfProfUsDataRateDs 1.3.6.1.2.1.10.1.1.5.2.1.1.16
Data Rate Threshold Up shift for downstream direction. An 'Up-shift rate change' event is triggered when the actual downstream data rate exceeds, by more than the threshold, the data rate at the last entry into Showtime. The parameter is coded in bit/s.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..200000000  

adsl2ChConfProfDsDataRateDs 1.3.6.1.2.1.10.1.1.5.2.1.1.17
Data Rate Threshold Downshift for downstream direction. A 'Down-shift rate change' event is triggered when the actual downstream data rate is below the data rate at the last entry into Showtime, by more than the threshold. The parameter is coded in bit/s.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..200000000  

adsl2ChConfProfUsDataRateUs 1.3.6.1.2.1.10.1.1.5.2.1.1.18
Data Rate Threshold Up shift for upstream direction. An 'Up-shift rate change' event is triggered when the actual upstream data rate exceeds, by more than the threshold, the data rate at the last entry into Showtime. The parameter is coded in bit/s.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..200000000  

adsl2ChConfProfDsDataRateUs 1.3.6.1.2.1.10.1.1.5.2.1.1.19
Data Rate Threshold Downshift for upstream direction. A 'Down-shift rate change' event is triggered when the actual upstream data rate is below the data rate at the last entry into Showtime, by more than the threshold. The parameter is coded in bit/s.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..200000000  

adsl2ChConfProfImaEnabled 1.3.6.1.2.1.10.1.1.5.2.1.1.20
IMA Mode Enable. The parameter enables the IMA operation mode in the ATM Data Path. Relevant only if the channel is of ATM Data Path. When in 'enable' state, the ATM data path should comply with the requirements for IMA transmission.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

adsl2ChConfProfRowStatus 1.3.6.1.2.1.10.1.1.5.2.1.1.21
This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'outOfService'), it must be first unreferenced from all associated templates.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

adsl2LineAlarmConfTemplateTable 1.3.6.1.2.1.10.1.1.5.3.1
The table adsl2LineConfTemplateTable contains ADSL2 line configuration template.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Adsl2LineAlarmConfTemplateEntry

adsl2LineAlarmConfTemplateEntry 1.3.6.1.2.1.10.1.1.5.3.1.1
The table adsl2LineAlarmConfTemplateTable contains ADSL2 line PM thresholds template. A default template with an index of 'DEFVAL' will always exist and its parameters will be set to vendor specific values, unless otherwise specified in this document
Status: current Access: not-accessible
OBJECT-TYPE    
  Adsl2LineAlarmConfTemplateEntry  

adsl2LAlarmConfTempTemplateName 1.3.6.1.2.1.10.1.1.5.3.1.1.1
This object identifies a row in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SnmpAdminString Size(1..32)  

adsl2LAlarmConfTempLineProfile 1.3.6.1.2.1.10.1.1.5.3.1.1.2
The value of this object identifies the row in the ADSL2 Line Thresholds Configuration Profile Table (adsl2LineAlarmConfProfileTable) that applies to this ADSL2 line.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString Size(1..32)  

adsl2LAlarmConfTempChan1ConfProfile 1.3.6.1.2.1.10.1.1.5.3.1.1.3
The value of this object identifies the row in the ADSL2 Channel Thresholds Configuration Profile Table (adsl2ChAlarmConfProfileTable) that applies for ADSL2 bearer channel #1. The channel profile name specified here must match the name of an existing row in the adsl2ChAlarmConfProfileTable table.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString Size(1..32)  

adsl2LAlarmConfTempChan2ConfProfile 1.3.6.1.2.1.10.1.1.5.3.1.1.4
The value of this object identifies the row in the ADSL2 Channel Thresholds Configuration Profile Table (adsl2ChAlarmConfProfileTable) that applies for ADSL2 bearer channel #2. The channel profile name specified here must match the name of an existing row in the adsl2ChAlarmConfProfileTable table. If the channel is unused, then the object is set to a zero length string.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString Size(0..32)  

adsl2LAlarmConfTempChan3ConfProfile 1.3.6.1.2.1.10.1.1.5.3.1.1.5
The value of this object identifies the row in the ADSL2 Channel Thresholds Configuration Profile Table (adsl2ChAlarmConfProfileTable) that applies for ADSL2 bearer channel #3. The channel profile name specified here must match the name of an existing row in the adsl2ChAlarmConfProfileTable table. This object may be set to a non-zero length string only if adsl2LAlarmConfTempChan2ConfProfile contains a non-zero length string.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString Size(0..32)  

adsl2LAlarmConfTempChan4ConfProfile 1.3.6.1.2.1.10.1.1.5.3.1.1.6
The value of this object identifies the row in the ADSL2 Channel Thresholds Configuration Profile Table (adsl2ChAlarmConfProfileTable) that applies for ADSL2 bearer channel #4. The channel profile name specified here must match the name of an existing row in the adsl2ChAlarmConfProfileTable table. This object may be set to a non-zero length string only if adsl2LAlarmConfTempChan3ConfProfile contains a non-zero length string.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString Size(0..32)  

adsl2LAlarmConfTempRowStatus 1.3.6.1.2.1.10.1.1.5.3.1.1.7
This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'outOfService'), it must be first unreferenced from all associated lines.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

adsl2LineAlarmConfProfileTable 1.3.6.1.2.1.10.1.1.5.3.2
The table adsl2LineAlarmConfProfileTable contains ADSL2 line PM thresholds profiles.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Adsl2LineAlarmConfProfileEntry

adsl2LineAlarmConfProfileEntry 1.3.6.1.2.1.10.1.1.5.3.2.1
The table adsl2LineAlarmConfProfileTable contains ADSL2 line PM thresholds profiles. A default profile with an index of 'DEFVAL' will always exist and its parameters will be set to vendor specific values, unless otherwise specified in this document
Status: current Access: not-accessible
OBJECT-TYPE    
  Adsl2LineAlarmConfProfileEntry  

adsl2LineAlarmConfProfileName 1.3.6.1.2.1.10.1.1.5.3.2.1.1
This object identifies a row in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SnmpAdminString Size(1..32)  

adsl2LineAlarmConfProfileAtucThresh15MinFecs 1.3.6.1.2.1.10.1.1.5.3.2.1.2
A threshold for the adsl2PMLCurr15MFecs counter, when adsl2PMLCurrUnit is ATUC {1}. The value 0 means that no threshold is specified for the associated counter.
Status: current Access: read-create
OBJECT-TYPE    
  HCPerfIntervalThreshold  

adsl2LineAlarmConfProfileAtucThresh15MinEs 1.3.6.1.2.1.10.1.1.5.3.2.1.3
A threshold for the adsl2PMLCurr15MEs counter, when adsl2PMLCurrUnit is ATUC {1}. The value 0 means that no threshold is specified for the associated counter.
Status: current Access: read-create
OBJECT-TYPE    
  HCPerfIntervalThreshold  

adsl2LineAlarmConfProfileAtucThresh15MinSes 1.3.6.1.2.1.10.1.1.5.3.2.1.4
A threshold for the adsl2PMLCurr15MSes counter, when adsl2PMLCurrUnit is ATUC {1}. The value 0 means that no threshold is specified for the associated counter.
Status: current Access: read-create
OBJECT-TYPE    
  HCPerfIntervalThreshold  

adsl2LineAlarmConfProfileAtucThresh15MinLoss 1.3.6.1.2.1.10.1.1.5.3.2.1.5
A threshold for the adsl2PMLCurr15MLoss counter, when adsl2PMLCurrUnit is ATUC {1}. The value 0 means that no threshold is specified for the associated counter.
Status: current Access: read-create
OBJECT-TYPE    
  HCPerfIntervalThreshold  

adsl2LineAlarmConfProfileAtucThresh15MinUas 1.3.6.1.2.1.10.1.1.5.3.2.1.6
A threshold for the adsl2PMLCurr15MUas counter, when adsl2PMLCurrUnit is ATUC {1}. The value 0 means that no threshold is specified for the associated counter.
Status: current Access: read-create
OBJECT-TYPE    
  HCPerfIntervalThreshold  

adsl2LineAlarmConfProfileAturThresh15MinFecs 1.3.6.1.2.1.10.1.1.5.3.2.1.7
A threshold for the adsl2PMLCurr15MFecs counter, when adsl2PMLCurrUnit is ATUR {2}. The value 0 means that no threshold is specified for the associated counter.
Status: current Access: read-create
OBJECT-TYPE    
  HCPerfIntervalThreshold  

adsl2LineAlarmConfProfileAturThresh15MinEs 1.3.6.1.2.1.10.1.1.5.3.2.1.8
A threshold for the adsl2PMLCurr15MEs counter, when adsl2PMLCurrUnit is ATUR {2}. The value 0 means that no threshold is specified for the associated counter.
Status: current Access: read-create
OBJECT-TYPE    
  HCPerfIntervalThreshold  

adsl2LineAlarmConfProfileAturThresh15MinSes 1.3.6.1.2.1.10.1.1.5.3.2.1.9
A threshold for the adsl2PMLCurr15MSes counter, when adsl2PMLCurrUnit is ATUR {2}. The value 0 means that no threshold is specified for the associated counter.
Status: current Access: read-create
OBJECT-TYPE    
  HCPerfIntervalThreshold  

adsl2LineAlarmConfProfileAturThresh15MinLoss 1.3.6.1.2.1.10.1.1.5.3.2.1.10
A threshold for the adsl2PMLCurr15MLoss counter, when adsl2PMLCurrUnit is ATUR {2}. The value 0 means that no threshold is specified for the associated counter.
Status: current Access: read-create
OBJECT-TYPE    
  HCPerfIntervalThreshold  

adsl2LineAlarmConfProfileAturThresh15MinUas 1.3.6.1.2.1.10.1.1.5.3.2.1.11
A threshold for the adsl2PMLCurr15MUas counter, when adsl2PMLCurrUnit is ATUR {2}. The value 0 means that no threshold is specified for the associated counter.
Status: current Access: read-create
OBJECT-TYPE    
  HCPerfIntervalThreshold  

adsl2LineAlarmConfProfileThresh15MinFailedFullInt 1.3.6.1.2.1.10.1.1.5.3.2.1.12
A threshold for the adsl2PMLCurrInit15MfailedFullInits counter. The value 0 means that no threshold is specified for the associated counter.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

adsl2LineAlarmConfProfileThresh15MinFailedShrtInt 1.3.6.1.2.1.10.1.1.5.3.2.1.13
A threshold for the adsl2PMLCurrInit15MFailedShortInits counter. The value 0 means that no threshold is specified for the associated counter.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

adsl2LineAlarmConfProfileRowStatus 1.3.6.1.2.1.10.1.1.5.3.2.1.14
This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'outOfService'), it must be first unreferenced from all associated templates.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

adsl2ChAlarmConfProfileTable 1.3.6.1.2.1.10.1.1.5.3.3
The table adsl2ChAlarmConfProfileTable contains ADSL2 channel PM thresholds profiles.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Adsl2ChAlarmConfProfileEntry

adsl2ChAlarmConfProfileEntry 1.3.6.1.2.1.10.1.1.5.3.3.1
The table adsl2ChAlarmConfProfileTable contains ADSL2 channel PM thresholds profiles. A default profile with an index of 'DEFVAL' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document
Status: current Access: not-accessible
OBJECT-TYPE    
  Adsl2ChAlarmConfProfileEntry  

adsl2ChAlarmConfProfileName 1.3.6.1.2.1.10.1.1.5.3.3.1.1
This object identifies a row in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SnmpAdminString Size(1..32)  

adsl2ChAlarmConfProfileAtucThresh15MinCodingViolations 1.3.6.1.2.1.10.1.1.5.3.3.1.2
A threshold for the adsl2PMChCurr15MCodingViolations counter, when adsl2PMChCurrUnit is ATUC {1}. The value 0 means that no threshold is specified for the associated counter.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

adsl2ChAlarmConfProfileAtucThresh15MinCorrected 1.3.6.1.2.1.10.1.1.5.3.3.1.3
A threshold for the adsl2PMChCurr15MCorrectedBlocks counter, when adsl2PMChCurrUnit is ATUC {1}. The value 0 means that no threshold is specified for the associated counter.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

adsl2ChAlarmConfProfileAturThresh15MinCodingViolations 1.3.6.1.2.1.10.1.1.5.3.3.1.4
A threshold for the adsl2PMChCurr15MCodingViolations counter, when adsl2PMChCurrUnit is ATUR {2}. The value 0 means that no threshold is specified for the associated counter.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

adsl2ChAlarmConfProfileAturThresh15MinCorrected 1.3.6.1.2.1.10.1.1.5.3.3.1.5
A threshold for the adsl2PMChCurr15MCorrectedBlocks counter, when adsl2PMChCurrUnit is ATUR {2}. The value 0 means that no threshold is specified for the associated counter.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

adsl2ChAlarmConfProfileRowStatus 1.3.6.1.2.1.10.1.1.5.3.3.1.6
This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'outOfService'), it must be first unreferenced from all associated templates.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

adsl2PMLineCurrTable 1.3.6.1.2.1.10.1.1.4.1.1
The table adsl2PMLineCurrTable contains current Performance Monitoring results of ADSL2 line.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Adsl2PMLineCurrEntry

adsl2PMLineCurrEntry 1.3.6.1.2.1.10.1.1.4.1.1.1
The table adsl2PMLineCurrTable contains current Performance Monitoring results of ADSL2 line. The index of this table is an interface index where the interface has an ifType of adsl2(230) and the termination unit.
Status: current Access: not-accessible
OBJECT-TYPE    
  Adsl2PMLineCurrEntry  

adsl2PMLCurrUnit 1.3.6.1.2.1.10.1.1.4.1.1.1.1
The termination unit ATUC{1} or ATUR{2}.
Status: current Access: not-accessible
OBJECT-TYPE    
  Adsl2Unit  

adsl2PMLCurrValidIntervals 1.3.6.1.2.1.10.1.1.4.1.1.1.2
Valid intervals.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2PMLCurrInvalidIntervals 1.3.6.1.2.1.10.1.1.4.1.1.1.3
Invalid intervals.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2PMLCurr15MTimeElapsed 1.3.6.1.2.1.10.1.1.4.1.1.1.4
Total elapsed seconds in this interval
Status: current Access: read-only
OBJECT-TYPE    
  HCPerfTimeElapsed  

adsl2PMLCurr15MFecs 1.3.6.1.2.1.10.1.1.4.1.1.1.5
Count of seconds during this interval that there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibited during UAS or SES.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adsl2PMLCurr15MEs 1.3.6.1.2.1.10.1.1.4.1.1.1.6
Count of seconds during this interval that there was: ATU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >=1 OR LPR >= 1 ATU-R: FEBE >= 1 for one or more bearer channels OR LOS-FE >=1 OR RDI >=1 OR LPR-FE >=1 . This parameter is inhibited during UAS.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adsl2PMLCurr15MSes 1.3.6.1.2.1.10.1.1.4.1.1.1.7
Count of seconds during this interval that there was: ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 ATU-R: (FEBE summed over all bearer channels) >= 18 OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1 . This parameter is inhibited during UAS.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adsl2PMLCurr15MLoss 1.3.6.1.2.1.10.1.1.4.1.1.1.8
Count of seconds during this interval that there was LOS (or LOS-FE for ATU-R).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adsl2PMLCurr15MUas 1.3.6.1.2.1.10.1.1.4.1.1.1.9
Count of seconds in Unavailability State during this interval. Unavailability begins at the onset of 10 contiguous severely-errored seconds, and ends at the onset of 10 contiguous seconds with no severely-errored seconds.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adsl2PMLCurr1DayValidIntervals 1.3.6.1.2.1.10.1.1.4.1.1.1.10
Valid intervals.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2PMLCurr1DayInvalidIntervals 1.3.6.1.2.1.10.1.1.4.1.1.1.11
Invalid intervals.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2PMLCurr1DayTimeElapsed 1.3.6.1.2.1.10.1.1.4.1.1.1.12
Total elapsed seconds in this interval.
Status: current Access: read-only
OBJECT-TYPE    
  HCPerfTimeElapsed  

adsl2PMLCurr1DayFecs 1.3.6.1.2.1.10.1.1.4.1.1.1.13
Count of seconds during this interval that there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibited during UAS or SES.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adsl2PMLCurr1DayEs 1.3.6.1.2.1.10.1.1.4.1.1.1.14
Count of seconds during this interval that there was: ATU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 ATU-R: FEBE >= 1 for one or more bearer channels OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1. This parameter is inhibited during UAS.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adsl2PMLCurr1DaySes 1.3.6.1.2.1.10.1.1.4.1.1.1.15
Count of seconds during this interval that there was: ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 ATU-R: (FEBE summed over all bearer channels) >= 18 OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1 This parameter is inhibited during UAS.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adsl2PMLCurr1DayLoss 1.3.6.1.2.1.10.1.1.4.1.1.1.16
Count of seconds during this interval that there was LOS (or LOS-FE for ATU-R).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adsl2PMLCurr1DayUas 1.3.6.1.2.1.10.1.1.4.1.1.1.17
Count of seconds in Unavailability State during this interval. Unavailability begins at the onset of 10 contiguous severely -errored seconds, and ends at the onset of 10 contiguous seconds with no severely-errored seconds.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adsl2PMLineCurrInitTable 1.3.6.1.2.1.10.1.1.4.1.2
The table adsl2PMLineCurrInitTable contains current initialization counters of ADSL2 line.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Adsl2PMLineCurrInitEntry

adsl2PMLineCurrInitEntry 1.3.6.1.2.1.10.1.1.4.1.2.1
The table adsl2PMLineCurrInitTable contains current initialization counters of ADSL2 line. The index of this table is an interface index where the interface has an ifType of adsl2(230) and the termination unit.
Status: current Access: not-accessible
OBJECT-TYPE    
  Adsl2PMLineCurrInitEntry  

adsl2PMLCurrInit15MTimeElapsed 1.3.6.1.2.1.10.1.1.4.1.2.1.1
Total elapsed seconds in this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2PMLCurrInit15MFullInits 1.3.6.1.2.1.10.1.1.4.1.2.1.2
Count of full initializations attempted on the line (successful and failed) during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2PMLCurrInit15MFailedFullInits 1.3.6.1.2.1.10.1.1.4.1.2.1.3
Count of failed full initializations on the line during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2PMLCurrInit15MShortInits 1.3.6.1.2.1.10.1.1.4.1.2.1.4
Count of short initializations attempted on the line (successful and failed) during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2PMLCurrInit15MFailedShortInits 1.3.6.1.2.1.10.1.1.4.1.2.1.5
Count of failed short initializations on the line during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2PMLCurrInit1DayTimeElapsed 1.3.6.1.2.1.10.1.1.4.1.2.1.6
Total elapsed seconds in this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2PMLCurrInit1DayFullInits 1.3.6.1.2.1.10.1.1.4.1.2.1.7
Count of full initializations attempted on the line (successful and failed) during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2PMLCurrInit1DayFailedFullInits 1.3.6.1.2.1.10.1.1.4.1.2.1.8
Count of failed full initializations on the line during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2PMLCurrInit1DayShortInits 1.3.6.1.2.1.10.1.1.4.1.2.1.9
Count of short initializations attempted on the line (successful and failed) during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2PMLCurrInit1DayFailedShortInits 1.3.6.1.2.1.10.1.1.4.1.2.1.10
Count of failed short initializations on the line during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2PMLineHist15MinTable 1.3.6.1.2.1.10.1.1.4.1.3
The table adsl2PMLineHist15MinTable contains PM line history for 15min intervals of ADSL2 line.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Adsl2PMLineHist15MinEntry

adsl2PMLineHist15MinEntry 1.3.6.1.2.1.10.1.1.4.1.3.1
The table adsl2PMLineHist15MinTable contains PM line history for 15min intervals of ADSL2 line. The index of this table is an interface index where the interface has an ifType of adsl2(230), the termination unit, and an interval number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Adsl2PMLineHist15MinEntry  

adsl2PMLHist15MUnit 1.3.6.1.2.1.10.1.1.4.1.3.1.1
The termination unit ATUC{1} or ATUR{2}.
Status: current Access: not-accessible
OBJECT-TYPE    
  Adsl2Unit  

adsl2PMLHist15MInterval 1.3.6.1.2.1.10.1.1.4.1.3.1.2
The interval number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

adsl2PMLHist15MMonitoredTime 1.3.6.1.2.1.10.1.1.4.1.3.1.3
Total seconds monitored in this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2PMLHist15MFecs 1.3.6.1.2.1.10.1.1.4.1.3.1.4
Count of seconds during this interval that there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibited during UAS or SES.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adsl2PMLHist15MEs 1.3.6.1.2.1.10.1.1.4.1.3.1.5
Count of seconds during this interval that there was: ATU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 ATU-R: FEBE >= 1 for one or more bearer channels OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1. This parameter is inhibited during UAS.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adsl2PMLHist15MSes 1.3.6.1.2.1.10.1.1.4.1.3.1.6
Count of seconds during this interval that there was: ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 ATU-R: (FEBE summed over all bearer channels) >= 18 OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1. This parameter is inhibited during UAS.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adsl2PMLHist15MLoss 1.3.6.1.2.1.10.1.1.4.1.3.1.7
Count of seconds during this interval that there was LOS (or LOS-FE for ATU-R).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adsl2PMLHist15MUas 1.3.6.1.2.1.10.1.1.4.1.3.1.8
Count of seconds in Unavailability State during this interval. Unavailability begins at the onset of 10 contiguous severely -errored seconds, and ends at the onset of 10 contiguous seconds with no severely-errored seconds.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adsl2PMLHist15MValidInterval 1.3.6.1.2.1.10.1.1.4.1.3.1.9
This variable indicates if the data for this interval is valid.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

adsl2PMLineHist1DayTable 1.3.6.1.2.1.10.1.1.4.1.4
The table adsl2PMLineHist1DayTable contains PM line history for 24 hours intervals of ADSL2 line.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Adsl2PMLineHist1DayEntry

adsl2PMLineHist1DayEntry 1.3.6.1.2.1.10.1.1.4.1.4.1
The table adsl2PMLineHist1DayTable contains PM line history for 24 hours intervals of ADSL2 line. The indexes of this table is an interface index where the interface has an ifType of adsl2(230), the termination unit and an interval number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Adsl2PMLineHist1DayEntry  

adsl2PMLHist1DUnit 1.3.6.1.2.1.10.1.1.4.1.4.1.1
The termination unit.
Status: current Access: not-accessible
OBJECT-TYPE    
  Adsl2Unit  

adsl2PMLHist1DInterval 1.3.6.1.2.1.10.1.1.4.1.4.1.2
The interval number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

adsl2PMLHist1DMonitoredTime 1.3.6.1.2.1.10.1.1.4.1.4.1.3
Total seconds monitored in this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2PMLHist1DFecs 1.3.6.1.2.1.10.1.1.4.1.4.1.4
Count of seconds during this interval that there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibited during UAS or SES.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adsl2PMLHist1DEs 1.3.6.1.2.1.10.1.1.4.1.4.1.5
Count of seconds during this interval that there was: ATU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 ATU-R: FEBE >= 1 for one or more bearer channels OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1. This parameter is inhibited during UAS.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adsl2PMLHist1DSes 1.3.6.1.2.1.10.1.1.4.1.4.1.6
Count of seconds during this interval that there was: ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR LOS >= 1 OR SEF >> 1 OR LPR >= 1 ATU-R: (FEBE summed over all bearer channels) >= 18 OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1. This parameter is inhibited during UAS.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adsl2PMLHist1DLoss 1.3.6.1.2.1.10.1.1.4.1.4.1.7
Count of seconds during this interval that there was LOS (or LOS-FE for ATU-R).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adsl2PMLHist1DUas 1.3.6.1.2.1.10.1.1.4.1.4.1.8
Count of seconds in Unavailability State during this interval. Unavailability begins at the onset of 10 contiguous severely -errored seconds, and ends at the onset of 10 contiguous seconds with no severely-errored seconds.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adsl2PMLHist1DValidInterval 1.3.6.1.2.1.10.1.1.4.1.4.1.9
This variable indicates if the data for this interval is valid.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

adsl2PMLineInitHist15MinTable 1.3.6.1.2.1.10.1.1.4.1.5
The table adsl2PMLineInitHist15MinTable contains PM line initialization history for 15 minutes intervals of ADSL2 line.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Adsl2PMLineInitHist15MinEntry

adsl2PMLineInitHist15MinEntry 1.3.6.1.2.1.10.1.1.4.1.5.1
The table adsl2PMLineInitHist15MinTable contains PM line initialization history for 15 minutes intervals of ADSL2 line. The index of this table is an interface index where the interface has an ifType of adsl2(230) and an interval number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Adsl2PMLineInitHist15MinEntry  

adsl2PMLHistInit15MInterval 1.3.6.1.2.1.10.1.1.4.1.5.1.1
The interval number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

adsl2PMLHistInit15MMonitoredTime 1.3.6.1.2.1.10.1.1.4.1.5.1.2
Total seconds monitored in this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2PMLHistInit15MFullInits 1.3.6.1.2.1.10.1.1.4.1.5.1.3
Count of full initializations attempted on the line (successful and failed) during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2PMLHistInit15MFailedFullInits 1.3.6.1.2.1.10.1.1.4.1.5.1.4
Count of failed full initializations on the line during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2PMLHistInit15MShortInits 1.3.6.1.2.1.10.1.1.4.1.5.1.5
Count of short initializations attempted on the line (successful and failed) during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2PMLHistInit15MFailedShortInits 1.3.6.1.2.1.10.1.1.4.1.5.1.6
Count of failed short initializations on the line during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2PMLHistInit15MValidInterval 1.3.6.1.2.1.10.1.1.4.1.5.1.7
This variable indicates if the data for this interval is valid.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

adsl2PMLineInitHist1DayTable 1.3.6.1.2.1.10.1.1.4.1.6
The table adsl2PMLineInitHist1DayTable contains PM line initialization history for 24 hours intervals of ADSL2 line.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Adsl2PMLineInitHist1DayEntry

adsl2PMLineInitHist1DayEntry 1.3.6.1.2.1.10.1.1.4.1.6.1
The table adsl2PMLineInitHist1DayTable contains PM line initialization history for 24 hours intervals of ADSL2 line. The indexes of this table is an interface index where the interface has an ifType of adsl2(230) and an interval number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Adsl2PMLineInitHist1DayEntry  

adsl2PMLHistinit1DInterval 1.3.6.1.2.1.10.1.1.4.1.6.1.1
The interval number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

adsl2PMLHistinit1DMonitoredTime 1.3.6.1.2.1.10.1.1.4.1.6.1.2
Total seconds monitored in this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2PMLHistinit1DFullInits 1.3.6.1.2.1.10.1.1.4.1.6.1.3
Count of full initializations attempted on the line (successful and failed) during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2PMLHistinit1DFailedFullInits 1.3.6.1.2.1.10.1.1.4.1.6.1.4
Count of failed full initializations on the line during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2PMLHistinit1DShortInits 1.3.6.1.2.1.10.1.1.4.1.6.1.5
Count of short initializations attempted on the line (successful and failed) during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2PMLHistinit1DFailedShortInits 1.3.6.1.2.1.10.1.1.4.1.6.1.6
Count of failed short initializations on the line during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2PMLHistinit1DValidInterval 1.3.6.1.2.1.10.1.1.4.1.6.1.7
This variable indicates if the data for this interval is valid.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

adsl2PMChCurrTable 1.3.6.1.2.1.10.1.1.4.2.1
The table adsl2PMChCurrTable contains current Performance Monitoring results of ADSL2 channel.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Adsl2PMChCurrEntry

adsl2PMChCurrEntry 1.3.6.1.2.1.10.1.1.4.2.1.1
The table adsl2PMChCurrTable contains current Performance Monitoring results of ADSL2 channel. The indexes of this table is an interface index where the interface has an ifType value which is applicable for a DSL channel and the termination unit.
Status: current Access: not-accessible
OBJECT-TYPE    
  Adsl2PMChCurrEntry  

adsl2PMChCurrUnit 1.3.6.1.2.1.10.1.1.4.2.1.1.1
The termination unit.
Status: current Access: not-accessible
OBJECT-TYPE    
  Adsl2Unit  

adsl2PMChCurrValidIntervals 1.3.6.1.2.1.10.1.1.4.2.1.1.2
Valid intervals.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2PMChCurrInvalidIntervals 1.3.6.1.2.1.10.1.1.4.2.1.1.3
Invalid intervals.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2PMChCurr15MTimeElapsed 1.3.6.1.2.1.10.1.1.4.2.1.1.4
Total elapsed seconds in this interval.
Status: current Access: read-only
OBJECT-TYPE    
  HCPerfTimeElapsed  

adsl2PMChCurr15MCodingViolations 1.3.6.1.2.1.10.1.1.4.2.1.1.5
Count of CRC-8 (FEBE for ATU-R) anomalies occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the CRC is applied over multiple channels, then each related CRC-8 (or FEBE) anomaly should increment each of the counters related to the individual channels.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2PMChCurr15MCorrectedBlocks 1.3.6.1.2.1.10.1.1.4.2.1.1.6
Count of FEC (FFEC for ATU-R) anomalies (corrected code words) occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the FEC is applied over multiple channels, then each related FEC (or FFEC) anomaly should increment each of the counters related to the individual channels.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2PMChCurr1DayValidIntervals 1.3.6.1.2.1.10.1.1.4.2.1.1.7
Valid intervals.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2PMChCurr1DayInvalidIntervals 1.3.6.1.2.1.10.1.1.4.2.1.1.8
Invalid intervals.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2PMChCurr1DayTimeElapsed 1.3.6.1.2.1.10.1.1.4.2.1.1.9
Total elapsed seconds in this interval.
Status: current Access: read-only
OBJECT-TYPE    
  HCPerfTimeElapsed  

adsl2PMChCurr1DayCodingViolations 1.3.6.1.2.1.10.1.1.4.2.1.1.10
Count of CRC-8 (FEBE for ATU-R) anomalies occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the CRC is applied over multiple channels, then each related CRC-8 (or FEBE) anomaly should increment each of the counters related to the individual channels.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2PMChCurr1DayCorrectedBlocks 1.3.6.1.2.1.10.1.1.4.2.1.1.11
Count of FEC (FFEC for ATU-R) anomalies (corrected code words) occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the FEC is applied over multiple channels, then each related FEC (or FFEC) anomaly should increment each of the counters related to the individual channels.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2PMChHist15MinTable 1.3.6.1.2.1.10.1.1.4.2.2
The table adsl2PMChCurrTable contains current Performance Monitoring results of ADSL2 channel.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Adsl2PMChHist15MinEntry

adsl2PMChHist15MinEntry 1.3.6.1.2.1.10.1.1.4.2.2.1
The table adsl2PMChCurrTable contains current Performance Monitoring results of ADSL2 channel. The indexes of this table is an interface index where the interface has an ifType value which is applicable for a DSL channel, the termination unit and the interval number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Adsl2PMChHist15MinEntry  

adsl2PMChHist15MUnit 1.3.6.1.2.1.10.1.1.4.2.2.1.1
The termination unit.
Status: current Access: not-accessible
OBJECT-TYPE    
  Adsl2Unit  

adsl2PMChHist15MInterval 1.3.6.1.2.1.10.1.1.4.2.2.1.2
The interval number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

adsl2PMChHist15MMonitoredTime 1.3.6.1.2.1.10.1.1.4.2.2.1.3
Total seconds monitored in this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2PMChHist15MCodingViolations 1.3.6.1.2.1.10.1.1.4.2.2.1.4
Count of CRC-8 (FEBE for ATU-R) anomalies occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the CRC is applied over multiple channels, then each related CRC-8 (or FEBE) anomaly should increment each of the counters related to the individual channels.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2PMChHist15MCorrectedBlocks 1.3.6.1.2.1.10.1.1.4.2.2.1.5
Count of FEC (FFEC for ATU-R) anomalies (corrected code words) occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the FEC is applied over multiple channels, then each related FEC (or FFEC) anomaly should increment each of the counters related to the individual channels.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2PMChHist15MValidInterval 1.3.6.1.2.1.10.1.1.4.2.2.1.6
This variable indicates if the data for this interval is valid.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

adsl2PMChHist1DTable 1.3.6.1.2.1.10.1.1.4.2.3
The table adsl2PMChHist1DayTable contains PM channel history for 1 day intervals of ADSL2.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Adsl2PMChHist1DEntry

adsl2PMChHist1DEntry 1.3.6.1.2.1.10.1.1.4.2.3.1
The table adsl2PMChHist1DayTable contains PM channel history for 1 day intervals of ADSL2. The indexes of this table is an interface index where the interface has an ifType value which is applicable for a DSL channel, the termination unit and the interval number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Adsl2PMChHist1DEntry  

adsl2PMChHist1DUnit 1.3.6.1.2.1.10.1.1.4.2.3.1.1
The termination unit.
Status: current Access: not-accessible
OBJECT-TYPE    
  Adsl2Unit  

adsl2PMChHist1DInterval 1.3.6.1.2.1.10.1.1.4.2.3.1.2
The interval number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

adsl2PMChHist1DMonitoredTime 1.3.6.1.2.1.10.1.1.4.2.3.1.3
Total seconds monitored in this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2PMChHist1DCodingViolations 1.3.6.1.2.1.10.1.1.4.2.3.1.4
Count of CRC-8 (FEBE for ATU-R) anomalies occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the CRC is applied over multiple channels, then each related CRC-8 (or FEBE) anomaly should increment each of the counters related to the individual channels.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2PMChHist1DCorrectedBlocks 1.3.6.1.2.1.10.1.1.4.2.3.1.5
Count of FEC (FFEC for ATU-R) anomalies (corrected code words) occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the FEC is applied over multiple channels, then each related FEC (or FFEC) anomaly should increment each of the counters related to the individual channels.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adsl2PMChHist1DValidInterval 1.3.6.1.2.1.10.1.1.4.2.3.1.6
This variable indicates if the data for this interval is valid.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

adsl2LinePerfFECSThreshAtuc 1.3.6.1.2.1.10.1.1.0.1
This notification indicates that the FEC seconds threshold has been reached/exceeded for the referred ATU-C.
Status: current Access: read-only
NOTIFICATION-TYPE    

adsl2LinePerfFECSThreshAtur 1.3.6.1.2.1.10.1.1.0.2
This notification indicates that the FEC seconds threshold has been reached/exceeded for the referred ATU-R.
Status: current Access: read-only
NOTIFICATION-TYPE    

adsl2LinePerfESThreshAtuc 1.3.6.1.2.1.10.1.1.0.3
This notification indicates that the errored seconds threshold has been reached/exceeded for the referred ATU-C.
Status: current Access: read-only
NOTIFICATION-TYPE    

adsl2LinePerfESThreshAtur 1.3.6.1.2.1.10.1.1.0.4
This notification indicates that the errored seconds threshold has been reached/exceeded for the referred ATU-R.
Status: current Access: read-only
NOTIFICATION-TYPE    

adsl2LinePerfSESThreshAtuc 1.3.6.1.2.1.10.1.1.0.5
This notification indicates that the severely-errored seconds threshold has been reached/exceeded for the referred ATU-C.
Status: current Access: read-only
NOTIFICATION-TYPE    

adsl2LinePerfSESThreshAtur 1.3.6.1.2.1.10.1.1.0.6
This notification indicates that the severely-errored seconds threshold has been reached/exceeded for the referred ATU-R.
Status: current Access: read-only
NOTIFICATION-TYPE    

adsl2LinePerfLOSSThreshAtuc 1.3.6.1.2.1.10.1.1.0.7
This notification indicates that the LOS seconds threshold has been reached/exceeded for the referred ATU-C.
Status: current Access: read-only
NOTIFICATION-TYPE    

adsl2LinePerfLOSSThreshAtur 1.3.6.1.2.1.10.1.1.0.8
This notification indicates that the LOS seconds threshold has been reached/exceeded for the referred ATU-R.
Status: current Access: read-only
NOTIFICATION-TYPE    

adsl2LinePerfUASThreshAtuc 1.3.6.1.2.1.10.1.1.0.9
This notification indicates that the unavailable seconds threshold has been reached/exceeded for the referred ATU-C.
Status: current Access: read-only
NOTIFICATION-TYPE    

adsl2LinePerfUASThreshAtur 1.3.6.1.2.1.10.1.1.0.10
This notification indicates that the unavailable seconds threshold has been reached/exceeded for the referred ATU-R.
Status: current Access: read-only
NOTIFICATION-TYPE    

adsl2LinePerfCodingViolationsThreshAtuc 1.3.6.1.2.1.10.1.1.0.11
This notification indicates that the coding violations threshold has been reached/exceeded for the referred ATU-C.
Status: current Access: read-only
NOTIFICATION-TYPE    

adsl2LinePerfCodingViolationsThreshAtur 1.3.6.1.2.1.10.1.1.0.12
This notification indicates that the coding violations threshold has been reached/exceeded for the referred ATU-R.
Status: current Access: read-only
NOTIFICATION-TYPE    

adsl2LinePerfCorrectedThreshAtuc 1.3.6.1.2.1.10.1.1.0.13
This notification indicates that the corrected blocks (FEC events) threshold has been reached/exceeded for the referred ATU-C.
Status: current Access: read-only
NOTIFICATION-TYPE    

adsl2LinePerfCorrectedThreshAtur 1.3.6.1.2.1.10.1.1.0.14
This notification indicates that the corrected blocks (FEC events) threshold has been reached/exceeded for the referred ATU-R.
Status: current Access: read-only
NOTIFICATION-TYPE    

adsl2LinePerfFailedFullInitThresh 1.3.6.1.2.1.10.1.1.0.15
This notification indicates that the failed full initializations threshold has been reached/exceeded for the referred ADSL/ADSL2 or ADSL2 line.
Status: current Access: read-only
NOTIFICATION-TYPE    

adsl2LinePerfFailedShortInitThresh 1.3.6.1.2.1.10.1.1.0.16
This notification indicates that the failed short initializations threshold has been reached/exceeded for the referred ADSL/ADSL2 or ADSL2 line.
Status: current Access: read-only
NOTIFICATION-TYPE    

adsl2LineStatusChangeAtuc 1.3.6.1.2.1.10.1.1.0.17
This notification indicates that a status change is detected for the referred ATU-C.
Status: current Access: read-only
NOTIFICATION-TYPE    

adsl2LineStatusChangeAtur 1.3.6.1.2.1.10.1.1.0.18
This notification indicates that a status change is detected for the referred ATU-R.
Status: current Access: read-only
NOTIFICATION-TYPE    

adsl2Groups 1.3.6.1.2.1.10.1.1.8.1
OBJECT IDENTIFIER    

adsl2Compliances 1.3.6.1.2.1.10.1.1.8.2
OBJECT IDENTIFIER    

adsl2LineMibCompliance 1.3.6.1.2.1.10.1.1.8.2.1
The compliance statement for SNMP entities which manage ADSL2 interfaces.
Status: current Access: read-only
MODULE-COMPLIANCE    

adsl2LineGroup 1.3.6.1.2.1.10.1.1.8.1.1
The group of configuration, status, and commands objects on the line level.
Status: current Access: read-only
OBJECT-GROUP    

adsl2ChannelStatusGroup 1.3.6.1.2.1.10.1.1.8.1.2
The group of status objects on the channel level.
Status: current Access: read-only
OBJECT-GROUP    

adsl2ChannelStatusAtmGroup 1.3.6.1.2.1.10.1.1.8.1.3
The group of status objects on the data path level when it is ATM.
Status: current Access: read-only
OBJECT-GROUP    

adsl2ChannelStatusPtmGroup 1.3.6.1.2.1.10.1.1.8.1.4
The group of status objects on the data path level when it is PTM.
Status: current Access: read-only
OBJECT-GROUP    

adsl2SCStatusGroup 1.3.6.1.2.1.10.1.1.8.1.5
The group of status objects on the sub-carrier level. They are updated as a result of a DELT process.
Status: current Access: read-only
OBJECT-GROUP    

adsl2LineInventoryGroup 1.3.6.1.2.1.10.1.1.8.1.6
The group of inventory objects per xTU.
Status: current Access: read-only
OBJECT-GROUP    

adsl2LineConfTemplateGroup 1.3.6.1.2.1.10.1.1.8.1.7
The group of objects in a line configuration template.
Status: current Access: read-only
OBJECT-GROUP    

adsl2LineConfProfGroup 1.3.6.1.2.1.10.1.1.8.1.8
The group of objects in a line configuration profile.
Status: current Access: read-only
OBJECT-GROUP    

adsl2LineConfProfRaGroup 1.3.6.1.2.1.10.1.1.8.1.9
The group of objects required for controlling the rate adaptive behavior of the line.
Status: current Access: read-only
OBJECT-GROUP    

adsl2LineConfProfMsgMinGroup 1.3.6.1.2.1.10.1.1.8.1.10
The group of objects required for controlling the rate reserved for Overhead traffic.
Status: current Access: read-only
OBJECT-GROUP    

adsl2LineConfProfModeSpecGroup 1.3.6.1.2.1.10.1.1.8.1.11
The group of objects in a line configuration profile that have an instance for each operation mode allowed.
Status: current Access: read-only
OBJECT-GROUP    

adsl2ChConfProfileGroup 1.3.6.1.2.1.10.1.1.8.1.12
The group of objects in a channel configuration profile.
Status: current Access: read-only
OBJECT-GROUP    

adsl2ChConfProfileAtmGroup 1.3.6.1.2.1.10.1.1.8.1.13
The group of configuration objects required when the data path is ATM.
Status: current Access: read-only
OBJECT-GROUP    

adsl2ChConfProfileMinResGroup 1.3.6.1.2.1.10.1.1.8.1.14
The group of configuration objects required for the reserved data rate.
Status: current Access: read-only
OBJECT-GROUP    

adsl2LineAlarmConfTemplateGroup 1.3.6.1.2.1.10.1.1.8.1.15
The group of objects in a line alarm template.
Status: current Access: read-only
OBJECT-GROUP    

adsl2LineAlarmConfProfileGroup 1.3.6.1.2.1.10.1.1.8.1.16
The group of objects in a line alarm profile.
Status: current Access: read-only
OBJECT-GROUP    

adsl2ChAlarmConfProfileGroup 1.3.6.1.2.1.10.1.1.8.1.17
The group of objects in a channel alarm profile.
Status: current Access: read-only
OBJECT-GROUP    

adsl2PMLineCurrGroup 1.3.6.1.2.1.10.1.1.8.1.18
The group of objects that report the line level counters for current PM intervals.
Status: current Access: read-only
OBJECT-GROUP    

adsl2PMLineCurrInitGroup 1.3.6.1.2.1.10.1.1.8.1.19
The group of objects that report the full initializations counters for current PM intervals.
Status: current Access: read-only
OBJECT-GROUP    

adsl2PMLineCurrInitShortGroup 1.3.6.1.2.1.10.1.1.8.1.20
The group of objects that report the short initializations counters for current PM intervals.
Status: current Access: read-only
OBJECT-GROUP    

adsl2PMLineHist15MinGroup 1.3.6.1.2.1.10.1.1.8.1.21
The group of line level PM counters for the previous 15 minutes intervals.
Status: current Access: read-only
OBJECT-GROUP    

adsl2PMLineHist1DayGroup 1.3.6.1.2.1.10.1.1.8.1.22
The group of line level PM counters for the previous 24 hours intervals.
Status: current Access: read-only
OBJECT-GROUP    

adsl2PMLineInitHist15MinGroup 1.3.6.1.2.1.10.1.1.8.1.23
The group of PM counters for the previous 15 minutes intervals full initializations.
Status: current Access: read-only
OBJECT-GROUP    

adsl2PMLineInitHist15MinShortGroup 1.3.6.1.2.1.10.1.1.8.1.24
The group of PM counters for the previous 15 minutes intervals short initializations.
Status: current Access: read-only
OBJECT-GROUP    

adsl2PMLineInitHist1DayGroup 1.3.6.1.2.1.10.1.1.8.1.25
The group of PM counters for the previous 24 hours intervals full initializations.
Status: current Access: read-only
OBJECT-GROUP    

adsl2PMLineInitHist1DayShortGroup 1.3.6.1.2.1.10.1.1.8.1.26
The group of PM counters for the previous 24 hours intervals short initializations.
Status: current Access: read-only
OBJECT-GROUP    

adsl2PMChCurrGroup 1.3.6.1.2.1.10.1.1.8.1.27
The group of objects that report the channel level counters for current PM intervals.
Status: current Access: read-only
OBJECT-GROUP    

adsl2PMChHist15MinGroup 1.3.6.1.2.1.10.1.1.8.1.28
The group of objects that report the channel level counters for previous 15 minutes PM intervals.
Status: current Access: read-only
OBJECT-GROUP    

adsl2PMChHist1DGroup 1.3.6.1.2.1.10.1.1.8.1.29
The group of objects that report the channel level counters for previous 24 hours PM intervals.
Status: current Access: read-only
OBJECT-GROUP    

adsl2ScalarSCGroup 1.3.6.1.2.1.10.1.1.8.1.30
The group of objects that report the available memory resources for DELT processes.
Status: current Access: read-only
OBJECT-GROUP    

adsl2ThreshNotificationGroup 1.3.6.1.2.1.10.1.1.8.1.31
This group supports notifications of significant conditions associated with ADSL2 lines.
Status: current Access: read-only
NOTIFICATION-GROUP    

adsl2StatusChangeNotificationGroup 1.3.6.1.2.1.10.1.1.8.1.32
This group supports notifications of thresholds crossing associated with ADSL2 lines.
Status: current Access: read-only
NOTIFICATION-GROUP