NETSCREEN-VPN-MON-MIB

File: NETSCREEN-VPN-MON-MIB.mib (15373 bytes)

Imported modules

NETSCREEN-SMI SNMPv2-SMI SNMPv2-TC

Imported symbols

netscreenVpn netscreenVpnMibModule Counter32
Integer32 IpAddress MODULE-IDENTITY
OBJECT-TYPE TimeTicks DisplayString

Defined Types

NsVpnMonEntry  
SEQUENCE    
  nsVpnMonIndex Integer32
  nsVpnMonInPlyId Integer32
  nsVpnMonOutPlyId Integer32
  nsVpnMonVpnName DisplayString
  nsVpnMonVsysName DisplayString
  nsVpnMonTunnelType INTEGER
  nsVpnMonEspEncAlg INTEGER
  nsVpnMonEspAuthAlg INTEGER
  nsVpnMonAhAlg INTEGER
  nsVpnMonKeyType INTEGER
  nsVpnMonP1Auth INTEGER
  nsVpnMonVpnType INTEGER
  nsVpnMonRmtGwIp IpAddress
  nsVpnMonRmtGwId DisplayString
  nsVpnMonMyGwIp IpAddress
  nsVpnMonMyGwId DisplayString
  nsVpnMonOutSpi Integer32
  nsVpnMonInSpi Integer32
  nsVpnMonMonState INTEGER
  nsVpnMonTunnelState INTEGER
  nsVpnMonP1State INTEGER
  nsVpnMonP1LifeTime Integer32
  nsVpnMonP2State INTEGER
  nsVpnMonP2LifeTime Integer32
  nsVpnMonP2LifeBytes Integer32
  nsVpnMonDelayAvg Integer32
  nsVpnMonDelayLast Integer32
  nsVpnMonAvail Integer32
  nsVpnMonSaId Integer32
  nsVpnMonGroupId Integer32
  nsVpnMonUsrId Integer32
  nsVpnMonStartSessRequestTime TimeTicks
  nsVpnMonStartSessEstTime TimeTicks
  nsVpnMonEndSessTime TimeTicks
  nsVpnMonBytesIn Counter32
  nsVpnMonBytesOut Counter32
  nsVpnMonPacketsIn Counter32
  nsVpnMonPacketsOut Counter32
  nsVpnMonIfIndex Integer32
  nsVpnMonUpdateTime TimeTicks
  nsVpnMonDN DisplayString
  nsVpnMonIfInfo Integer32

Defined Values

netscreenVpnMonMibModule 1.3.6.1.4.1.3224.4.0.1
This module defines the object that are used to monitor VPN tunnels
MODULE-IDENTITY    

netscreenVpnMon 1.3.6.1.4.1.3224.4.1
OBJECT IDENTIFIER    

nsVpnMonTable 1.3.6.1.4.1.3224.4.1.1
A list of active VPN tunnel entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NsVpnMonEntry

nsVpnMonEntry 1.3.6.1.4.1.3224.4.1.1.1
A VPN tunnel entry containing attributes for both IKE Phase 1 and Phase 2 as well as associated policy
Status: current Access: not-accessible
OBJECT-TYPE    
  NsVpnMonEntry  

nsVpnMonIndex 1.3.6.1.4.1.3224.4.1.1.1.1
A unique value for each active VPN tunnel. Its value ranges between 1 and 65535 and may not be contiguous. Due to the dynamic nature of active VPN tunnels, the index has no other meaning but a pure index
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..2147483647  

nsVpnMonInPlyId 1.3.6.1.4.1.3224.4.1.1.1.2
The incoming policy ID for which this tunnel is created for. -1 means no policy associates with this SA.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nsVpnMonOutPlyId 1.3.6.1.4.1.3224.4.1.1.1.3
The outgoing policy ID for which this tunnel is created for. -1 means no policy associates with this SA.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nsVpnMonVpnName 1.3.6.1.4.1.3224.4.1.1.1.4
A textual string contains information about the VPN entity from which this tunnel was derived.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

nsVpnMonVsysName 1.3.6.1.4.1.3224.4.1.1.1.5
A textual string contains the Virtual system to which this tunnel belongs.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

nsVpnMonTunnelType 1.3.6.1.4.1.3224.4.1.1.1.6
Protocol type used for the tunnel
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER reserved(0), proto-isakmp(1), proto-ipsec-ah(2), proto-ipsec-esp(3), proto-ipcomp(4)  

nsVpnMonEspEncAlg 1.3.6.1.4.1.3224.4.1.1.1.7
a value which identifies a particular algorithm to be used to provide secrecy protection for ESP.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER reserved(0), esp-des-iv64(1), esp-des(2), esp-3des(3), esp-rc5(4), esp-idea(5), esp-cast(6), esp-blowfish(7), esp-3idea(8), esp-des-iv32(9), esp-rc4(10), esp-null(11), esp-aes(12), esp-aes192(20), esp-aes256(21)  

nsVpnMonEspAuthAlg 1.3.6.1.4.1.3224.4.1.1.1.8
The ESP Authentication Algorithm used in the IPsec.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER reserved(0), hmac-md5(1), hmac-sha(2), des-mac(3), ipdk(4)  

nsVpnMonAhAlg 1.3.6.1.4.1.3224.4.1.1.1.9
a value which identifies a particular algorithm to be used to provide integrity protection for AH.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER reserved(0), ah-md5(2), ah-sha(3), ah-des(4)  

nsVpnMonKeyType 1.3.6.1.4.1.3224.4.1.1.1.10
a value which identifies a key exchange protocol to be used for the negotiation
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER manual(0), auto-ike(1)  

nsVpnMonP1Auth 1.3.6.1.4.1.3224.4.1.1.1.11
a value which identifies Phase 1 authentication method
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unused(0), preshared-key(1), dss-Signature(2), rsa-Signature(3), rsa-Encryption1(4), rsa-Encryption2(5)  

nsVpnMonVpnType 1.3.6.1.4.1.3224.4.1.1.1.12
The type of this VPN tunnel, either a dialup or site-to-site
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER reserved(0), dialup(1), site-to-site(2)  

nsVpnMonRmtGwIp 1.3.6.1.4.1.3224.4.1.1.1.13
The peer Gateway's IP address
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

nsVpnMonRmtGwId 1.3.6.1.4.1.3224.4.1.1.1.14
The peer Gateway's ID
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

nsVpnMonMyGwIp 1.3.6.1.4.1.3224.4.1.1.1.15
The local Gateway's IP address
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

nsVpnMonMyGwId 1.3.6.1.4.1.3224.4.1.1.1.16
The local Gateway's ID
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

nsVpnMonOutSpi 1.3.6.1.4.1.3224.4.1.1.1.17
The SPI for outgoing packets
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nsVpnMonInSpi 1.3.6.1.4.1.3224.4.1.1.1.18
The SPI for incoming packets
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nsVpnMonMonState 1.3.6.1.4.1.3224.4.1.1.1.19
The monitoring status, if it is on, an icmp ping will be sent over the tunnel periodically to test the connectivity and latency
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER off(0), on(1)  

nsVpnMonTunnelState 1.3.6.1.4.1.3224.4.1.1.1.20
The current tunnel status determined by the icmp ping if The monitoring status is on.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER down(0), up(1)  

nsVpnMonP1State 1.3.6.1.4.1.3224.4.1.1.1.21
The IKE's Phase 1 status
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER inactive(0), active(1)  

nsVpnMonP1LifeTime 1.3.6.1.4.1.3224.4.1.1.1.22
an active Phase 1 sa's time left before re-key. -1 means unlimited lifetime.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nsVpnMonP2State 1.3.6.1.4.1.3224.4.1.1.1.23
The IKE's Phase 2 status
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER inactive(0), active(1)  

nsVpnMonP2LifeTime 1.3.6.1.4.1.3224.4.1.1.1.24
an active Phase 2 sa's time left before re-key. -1 means unlimited life time.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nsVpnMonP2LifeBytes 1.3.6.1.4.1.3224.4.1.1.1.25
an active Phase 2 sa's bytes left before re-key. -1 means unlimited life bytes.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nsVpnMonDelayAvg 1.3.6.1.4.1.3224.4.1.1.1.26
a kind of rolling average of latency, in milliseconds. -1 has no meaning here, which means nsVpnMonDelayAvg has not been calculated yet.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nsVpnMonDelayLast 1.3.6.1.4.1.3224.4.1.1.1.27
latency in last sample, in milliseconds. -1 means either vpn tunnel is inactive or vpn tunnel monitor is not turned on.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nsVpnMonAvail 1.3.6.1.4.1.3224.4.1.1.1.28
percentage over 30 samples
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nsVpnMonSaId 1.3.6.1.4.1.3224.4.1.1.1.29
SA identifier, also used as table index
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nsVpnMonGroupId 1.3.6.1.4.1.3224.4.1.1.1.30
Group Identifier
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nsVpnMonUsrId 1.3.6.1.4.1.3224.4.1.1.1.31
User Identifier
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nsVpnMonStartSessRequestTime 1.3.6.1.4.1.3224.4.1.1.1.32
Start Session request timestamp
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

nsVpnMonStartSessEstTime 1.3.6.1.4.1.3224.4.1.1.1.33
Start Session establish timestamp
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

nsVpnMonEndSessTime 1.3.6.1.4.1.3224.4.1.1.1.34
End Session timestamp [when session terminates]
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

nsVpnMonBytesIn 1.3.6.1.4.1.3224.4.1.1.1.35
Incoming bytes through this sa.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nsVpnMonBytesOut 1.3.6.1.4.1.3224.4.1.1.1.36
Outgoing bytes through this sa.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nsVpnMonPacketsIn 1.3.6.1.4.1.3224.4.1.1.1.37
Incoming packets through this sa.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nsVpnMonPacketsOut 1.3.6.1.4.1.3224.4.1.1.1.38
Outgoing packets through this sa.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nsVpnMonIfIndex 1.3.6.1.4.1.3224.4.1.1.1.39
interface index.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nsVpnMonUpdateTime 1.3.6.1.4.1.3224.4.1.1.1.40
Timestamp [Whenever any member of the row gets updated, the timestamp is updated]
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

nsVpnMonDN 1.3.6.1.4.1.3224.4.1.1.1.41
DN name
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..64)  

nsVpnMonIfInfo 1.3.6.1.4.1.3224.4.1.1.1.42
Internal id assigned to this interface. Stays persistent across resets.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..2147483647