NETGEAR-DCBX-MIB

File: NETGEAR-DCBX-MIB.mib (18823 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC IF-MIB
QUANTA-LB6M-REF-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Integer32
Unsigned32 TEXTUAL-CONVENTION MacAddress
RowStatus InterfaceIndex lb6m

Defined Types

DcbxPortRole  
.
TEXTUAL-CONVENTION    
  INTEGER manual(1), autoup(2), autodown(3), configSource(4)  

DcbxVersion  
.
TEXTUAL-CONVENTION    
  INTEGER auto(1), ieee(2), cin(3), cee(4)  

AgentDcbxEntry  
SEQUENCE    
  agentDcbxIntfIndex InterfaceIndex
  agentDcbxAutoCfgPortRole DcbxPortRole
  agentDcbxVersion DcbxVersion
  agentDcbxSupportedTLVs BITS
  agentDcbxConfigTLVsTxEnable BITS

AgentDcbxStatusEntry  
SEQUENCE    
  agentDcbxIntfIndex InterfaceIndex
  agentDcbxOperVersion DcbxVersion
  agentDcbxPeerMACaddress MacAddress
  agentDcbxCfgSource INTEGER
  agentDcbxMultiplePeerCount Unsigned32
  agentDcbxPeerRemovedCount Unsigned32
  agentDcbxPeerOperVersionNum Unsigned32
  agentDcbxPeerMaxVersion Unsigned32
  agentDcbxSeqNum Unsigned32
  agentDcbxAckNum Unsigned32
  agentDcbxPeerRcvdAckNum Unsigned32
  agentDcbxTxCount Unsigned32
  agentDcbxRxCount Unsigned32
  agentDcbxErrorFramesCount Unsigned32
  agentDcbxUnknownTLVsCount Unsigned32

Defined Values

fastPathDCBX 1.3.6.1.4.1.4413.1.1.58
The MIB definitions Data Center Bridging Exchange Protocol.
MODULE-IDENTITY    

agentDcbxGroup 1.3.6.1.4.1.4413.1.1.58.1
OBJECT IDENTIFIER    

agentDcbxTable 1.3.6.1.4.1.4413.1.1.58.1.1
A table providing configuration of DCBX per interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentDcbxEntry

agentDcbxEntry 1.3.6.1.4.1.4413.1.1.58.1.1.1
DCBX configuration for a port.
Status: current Access: not-accessible
OBJECT-TYPE    
  AgentDcbxEntry  

agentDcbxIntfIndex 1.3.6.1.4.1.4413.1.1.58.1.1.1.1
This is a unique index for an entry in the agentDcbxTable. A non-zero value indicates the ifIndex for the corresponding interface entry in the ifTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

agentDcbxAutoCfgPortRole 1.3.6.1.4.1.4413.1.1.58.1.1.1.2
Ports operating in the manual role do not have their configuration affected by peer devices or by internal propagation of configuration. These ports will advertise their configuration to their peer if DCBX is enabled on that port. Auto-up: Advertises a configuration, but is also willing to accept a configuration from the link-partner and propagate it internally to the auto-downstream ports as well as receive configuration propagated internally by other auto-upstream ports. Auto-down: Advertises a configuration but is not willing to accept one from the link partner. However, the port will accept a configuration propagated internally by the configuration source. Configuration Source:In this role, the port has been manually selected to be the configuration source. Configuration received over this port is propagated to the other auto-configuration ports.
Status: current Access: read-write
OBJECT-TYPE    
  DcbxPortRole  

agentDcbxVersion 1.3.6.1.4.1.4413.1.1.58.1.1.1.3
CIN is Cisco Intel Nuova DCBX (version 1.0). CEE is converged enhanced ethernet DCBX (version 1.06). IEEE is 802-1 az version. The default value is auto. DCBX supports the legacy implementations v1.0 (CIN) and v1.06 (CEE) in addition to standard IEEE version 2.4 DCBX. 1.DCBX starts in standard IEEE mode by sending an IEEE standard version 2.4 DCBX frame. If the peer responds, then IEEE standard version 2.4 DCBX is used,Starts means after a link up, a DCBX timeout (or multiple peer condition) or when commanded by the network operator. If DCBX receives a DCBX frame with an OUI indicating a legacy version, it immediately switches into legacy mode for the detected version and does not wait for the 3x LLDP fast timeout. 2.If no IEEE DCBX response is received within 3 times the LLDP fast transmit timeout period, DCBX immediately transmits a version 1.06 DCBX frame with the appropriate version number. If DCBX receives a DCBX frame with an OUI indicating IEEE standard support, it immediately switches into IEEE standard mode and does not wait for the timer. If DCBX receives a DCBX frame with an OUI indicating legacy mode and a version number indicating version 1.0 support, it immediately switches into legacy 1.0 mode and does not wait for the timer. 3.If no version 1.06 response is received within 3 times the DCBX fast transmit timeout period, DCBX falls back to version 1.0 and immediately transmits a version 1.0 frame. If no response is received within 3 times the DCBX fast transmit period, DCBX waits the standard LLDP timeout period, and then begins again with step 1. If DCBX receives a DCBX frame with an OUI indicating IEEE standard mode, it immediately switches into IEEE standard mode.
Status: deprecated Access: read-write
OBJECT-TYPE    
  DcbxVersion  

agentDcbxSupportedTLVs 1.3.6.1.4.1.4413.1.1.58.1.1.1.4
Bitmap that includes the supported set of DCBX LLDP TLVs the device is capable of and whose transmission is allowed on the local LLDP agent by network management. Having the bit 'pfc(0)' set indicates that the LLDP transmit PFC TLV as part of DCBX TLVs. Having the bit 'etcConfig(1)' set indicates that the LLDP transmit ETS configuration TLV as part of DCBX TLVs. Having the bit 'etsRecom(2)' set indicates that transmit ETS Recomdenation TLV as part of DCBX TLVs. Having the bit 'applicationPriority(3)' set indicates that the LLDP transmit applicationPriority TLV as part of DCBX TLVs.
Status: current Access: read-only
OBJECT-TYPE    
  BITS pfc(0), etsConfig(1), etsRecom(2), applicationPriority(3)  

agentDcbxConfigTLVsTxEnable 1.3.6.1.4.1.4413.1.1.58.1.1.1.5
Bitmap that includes the DCBX defined set of LLDP TLVs the device is capable of and whose transmission is allowed on the local LLDP agent by network management. Having the bit 'pfc(0)' set indicates that the LLDP transmit PFC TLV as part of DCBX TLVs. Having the bit 'etcConfig(1)' set indicates that the LLDP transmit ETS configuration TLV as part of DCBX TLVs. Having the bit 'etsRecom(2)' set indicates that transmit ETS Recomdenation TLV as part of DCBX TLVs. Having the bit 'applicationPriority(3)' set indicates that the LLDP transmit applicationPriority TLV as part of DCBX TLVs.
Status: current Access: read-write
OBJECT-TYPE    
  BITS pfc(0), etsConfig(1), etsRecom(2), applicationPriority(3)  

agentDcbxStatusTable 1.3.6.1.4.1.4413.1.1.58.1.2
.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgentDcbxStatusEntry

agentDcbxStatusEntry 1.3.6.1.4.1.4413.1.1.58.1.2.1
.
Status: current Access: not-accessible
OBJECT-TYPE    
  AgentDcbxStatusEntry  

agentDcbxOperVersion 1.3.6.1.4.1.4413.1.1.58.1.2.1.2
Specifies the DCBX mode in which the interface is currently operating.
Status: current Access: read-only
OBJECT-TYPE    
  DcbxVersion  

agentDcbxPeerMACaddress 1.3.6.1.4.1.4413.1.1.58.1.2.1.3
MAC Address of the DCBX peer.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

agentDcbxCfgSource 1.3.6.1.4.1.4413.1.1.58.1.2.1.4
Indicates if this port is the source of configuration information for auto-* ports.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER true(1), false(0)  

agentDcbxMultiplePeerCount 1.3.6.1.4.1.4413.1.1.58.1.2.1.5
Indicates number of times multiple peers were detected. A duplicate peer is when more than one DCBX peer is detected on a port.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

agentDcbxPeerRemovedCount 1.3.6.1.4.1.4413.1.1.58.1.2.1.6
.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

agentDcbxPeerOperVersionNum 1.3.6.1.4.1.4413.1.1.58.1.2.1.7
Specifies the operational version of the peer DCBX device. Valid only when peer device is a CEE/CIN DCBX device.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

agentDcbxPeerMaxVersion 1.3.6.1.4.1.4413.1.1.58.1.2.1.8
Specifies the max version of the peer DCBX device. Valid only when peer device is CEE/CIN DCBX device.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

agentDcbxSeqNum 1.3.6.1.4.1.4413.1.1.58.1.2.1.9
Specifies the current sequence number that is sent in DCBX control TLVs in CEE/CIN Mode.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

agentDcbxAckNum 1.3.6.1.4.1.4413.1.1.58.1.2.1.10
Specifies the current ACK number that is to be sent to peer in DCBX control TLVs in CEE/CIN Mode.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

agentDcbxPeerRcvdAckNum 1.3.6.1.4.1.4413.1.1.58.1.2.1.11
Specifies the current ACK number that is sent by peer in DCBX control TLV in CEE/CIN Mode.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

agentDcbxTxCount 1.3.6.1.4.1.4413.1.1.58.1.2.1.12
The number of DCBX frames transmitted per interface.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

agentDcbxRxCount 1.3.6.1.4.1.4413.1.1.58.1.2.1.13
The number of DCBX frames received per interface.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

agentDcbxErrorFramesCount 1.3.6.1.4.1.4413.1.1.58.1.2.1.14
The number of DCBX frames discarded due to errors in the frame.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

agentDcbxUnknownTLVsCount 1.3.6.1.4.1.4413.1.1.58.1.2.1.15
The number of DCBX (PFC, ETS, Application Priority or other) TLVs not recognized.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

agentDcbxGroupGlobalConfGroup 1.3.6.1.4.1.4413.1.1.58.1.3
OBJECT IDENTIFIER    

agentDcbxGlobalConfVersion 1.3.6.1.4.1.4413.1.1.58.1.3.1
CIN is Cisco Intel Nuova DCBX (version 1.0). CEE is converged enhanced ethernet DCBX (version 1.06). IEEE is 802-1 az version. The default value is auto. DCBX supports the legacy implementations v1.0 (CIN) and v1.06 (CEE) in addition to standard IEEE version 2.4 DCBX. 1.DCBX starts in standard IEEE mode by sending an IEEE standard version 2.4 DCBX frame. If the peer responds, then IEEE standard version 2.4 DCBX is used,Starts means after a link up, a DCBX timeout (or multiple peer condition) or when commanded by the network operator. If DCBX receives a DCBX frame with an OUI indicating a legacy version, it immediately switches into legacy mode for the detected version and does not wait for the 3x LLDP fast timeout. 2.If no IEEE DCBX response is received within 3 times the LLDP fast transmit timeout period, DCBX immediately transmits a version 1.06 DCBX frame with the appropriate version number. If DCBX receives a DCBX frame with an OUI indicating IEEE standard support, it immediately switches into IEEE standard mode and does not wait for the timer. If DCBX receives a DCBX frame with an OUI indicating legacy mode and a version number indicating version 1.0 support, it immediately switches into legacy 1.0 mode and does not wait for the timer. 3.If no version 1.06 response is received within 3 times the DCBX fast transmit timeout period, DCBX falls back to version 1.0 and immediately transmits a version 1.0 frame. If no response is received within 3 times the DCBX fast transmit period, DCBX waits the standard LLDP timeout period, and then begins again with step 1. If DCBX receives a DCBX frame with an OUI indicating IEEE standard mode, it immediately switches into IEEE standard mode.
Status: current Access: read-write
OBJECT-TYPE    
  DcbxVersion