NETCOM-MIB

File: NETCOM-MIB.mib (11353 bytes)

Imported modules

SNMPv2-SMI RFC-1215 RFC1213-MIB
RFC-1212 SNMPv2-CONF SNMPv2-TC
RFC1155-SMI

Imported symbols

OBJECT-TYPE TRAP-TYPE DisplayString
OBJECT-TYPE MODULE-COMPLIANCE OBJECT-GROUP
TEXTUAL-CONVENTION enterprises

Defined Values

sinetica 1.3.6.1.4.1.3711
OBJECT IDENTIFIER    

netcom 1.3.6.1.4.1.3711.7
OBJECT IDENTIFIER    

netcom1 1.3.6.1.4.1.3711.7.1
OBJECT IDENTIFIER    

netcomObjects 1.3.6.1.4.1.3711.7.1.1
OBJECT IDENTIFIER    

netcomEnvironment 1.3.6.1.4.1.3711.7.1.1.1
OBJECT IDENTIFIER    

netcomContact 1.3.6.1.4.1.3711.7.1.1.2
OBJECT IDENTIFIER    

netcomEnvHumidity 1.3.6.1.4.1.3711.7.1.1.1.1
OBJECT IDENTIFIER    

netcomEnvTemperature 1.3.6.1.4.1.3711.7.1.1.1.2
OBJECT IDENTIFIER    

netcomEnvHumidityEnableMonitoring 1.3.6.1.4.1.3711.7.1.1.1.1.1
Setting to one enables monitoring of Humidity
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..1  

netcomEnvCurrentHumidity 1.3.6.1.4.1.3711.7.1.1.1.1.2
The current humidity reading in 0.1%
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..1000  

netcomEnvHumidityLowerThreshold 1.3.6.1.4.1.3711.7.1.1.1.1.3
The Lower humidity threshold in 0.1%
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..1000  

netcomEnvHumidityUpperThreshold 1.3.6.1.4.1.3711.7.1.1.1.1.4
The Upper humidity threshold in 0.1%
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..1000  

netcomEnvHumidityCalibrationOffset 1.3.6.1.4.1.3711.7.1.1.1.1.5
Calibration offset in 0.1%
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER -100..100  

netcomLowHumidity 21
The NetCom-th unit is below the low humidity threshold.
TRAP-TYPE    

netcomHighHumidity 22
The NetCom-th unit is above the high humidity threshold.
TRAP-TYPE    

netcomHumidityReturnToNormal 23
The NetCom-th unit has returned to normal humidity
TRAP-TYPE    

netcomEnvTemperatureEnableMonitoring 1.3.6.1.4.1.3711.7.1.1.1.2.1
Setting to one enables monitoring of Temperature
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..1  

netcomEnvCurrentTemperature 1.3.6.1.4.1.3711.7.1.1.1.2.2
The current temperature reading in 0.1%
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -200..1000  

netcomEnvTemperatureLowerThreshold 1.3.6.1.4.1.3711.7.1.1.1.2.3
The Lower temperature threshold in 0.1 degrees
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER -200..1000  

netcomEnvTemperatureUpperThreshold 1.3.6.1.4.1.3711.7.1.1.1.2.4
The Upper temperature threshold in 0.1 degrees
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER -200..1000  

netcomEnvTemperatureCalibrationOffset 1.3.6.1.4.1.3711.7.1.1.1.2.5
Calibration offset in 0.1 degrees
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER -100..100  

netcomLowTemperature 31
The NetCom-th unit is below the lower temperature threshold.
TRAP-TYPE    

netcomHighTemperature 32
The NetCom-th unit is above the high temperature threshold.
TRAP-TYPE    

netcomTemperatureReturnToNormal 33
The NetCom-th unit has returned to normal temperature
TRAP-TYPE    

netcomContactEnable 1.3.6.1.4.1.3711.7.1.1.2.1
Setting to one enables monitoring of contacts
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..1  

netcomContactNormalStates 1.3.6.1.4.1.3711.7.1.1.2.2
OBJECT IDENTIFIER    

netcomContactCurrentStates 1.3.6.1.4.1.3711.7.1.1.2.3
OBJECT IDENTIFIER    

netcomContact1NormalState 1.3.6.1.4.1.3711.7.1.1.2.2.1
Set to 0 for normally open condition, 1 for normally closed
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..1  

netcomContact2NormalState 1.3.6.1.4.1.3711.7.1.1.2.2.2
Set to 0 for normally open condition, 1 for normally closed
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..1  

netcomContact3NormalState 1.3.6.1.4.1.3711.7.1.1.2.2.3
Set to 0 for normally open condition, 1 for normally closed
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..1  

netcomContact4NormalState 1.3.6.1.4.1.3711.7.1.1.2.2.4
Set to 0 for normally open condition, 1 for normally closed
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..1  

netcomContact5NormalState 1.3.6.1.4.1.3711.7.1.1.2.2.5
Set to 0 for normally open condition, 1 for normally closed
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..1  

netcomContact6NormalState 1.3.6.1.4.1.3711.7.1.1.2.2.6
Set to 0 for normally open condition, 1 for normally closed
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..1  

netcomContact7NormalState 1.3.6.1.4.1.3711.7.1.1.2.2.7
Set to 0 for normally open condition, 1 for normally closed
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..1  

netcomContact1CurrentState 1.3.6.1.4.1.3711.7.1.1.2.3.1
The current state of the contact
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..1  

netcomContact2CurrentState 1.3.6.1.4.1.3711.7.1.1.2.3.2
The current state of the contact
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..1  

netcomContact3CurrentState 1.3.6.1.4.1.3711.7.1.1.2.3.3
The current state of the contact
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..1  

netcomContact4CurrentState 1.3.6.1.4.1.3711.7.1.1.2.3.4
The current state of the contact
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..1  

netcomContact5CurrentState 1.3.6.1.4.1.3711.7.1.1.2.3.5
The current state of the contact
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..1  

netcomContact6CurrentState 1.3.6.1.4.1.3711.7.1.1.2.3.6
The current state of the contact
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..1  

netcomContact7CurrentState 1.3.6.1.4.1.3711.7.1.1.2.3.7
The current state of the contact
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..1  

netcomContact1NonNormal 1
The NetCom has detected a non-normal state on contact 1
TRAP-TYPE    

netcomContact1ReturnToNormal 11
The NetCom has detected a return to normal state on contact 1
TRAP-TYPE    

netcomContact2NonNormal 2
The NetCom has detected a non-normal state on contact 2
TRAP-TYPE    

netcomContact2ReturnToNormal 12
The NetCom has detected a return to normal state on contact 2
TRAP-TYPE    

netcomContact3NonNormal 3
The NetCom has detected a non-normal state on contact 3
TRAP-TYPE    

netcomContact3ReturnToNormal 13
The NetCom has detected a return to normal state on contact 3
TRAP-TYPE    

netcomContact4NonNormal 4
The NetCom has detected a non-normal state on contact 4
TRAP-TYPE    

netcomContact4ReturnToNormal 14
The NetCom has detected a return to normal state on contact 4
TRAP-TYPE    

netcomContact5NonNormal 5
The NetCom has detected a non-normal state on contact 5
TRAP-TYPE    

netcomContact5ReturnToNormal 15
The NetCom has detected a return to normal state on contact 5
TRAP-TYPE    

netcomContact6NonNormal 6
The NetCom has detected a non-normal state on contact 6
TRAP-TYPE    

netcomContact6ReturnToNormal 16
The NetCom has detected a return to normal state on contact 6
TRAP-TYPE    

netcomContact7NonNormal 7
The NetCom has detected a non-normal state on contact 7
TRAP-TYPE    

netcomContact7ReturnToNormal 17
The NetCom has detected a return to normal state on contact 7
TRAP-TYPE    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor