NB30MIB

File: NB30MIB.mib (60446 bytes)

Imported modules

RFC-1212 RFC1155-SMI IRM-OIDS

Imported symbols

OBJECT-TYPE Counter nb30Rev1

Defined Types

Nb30DsxEntry  
SEQUENCE    
  nb30DsxChannelControl INTEGER
  nb30DsxChannelId INTEGER

Nb30PortEntry  
SEQUENCE    
  nb30PortAddress OCTET STRING
  nb30PortName OCTET STRING
  nb30PortType OCTET STRING
  nb30PortStatus OCTET STRING
  nb30PortNetName OCTET STRING
  nb30PortFrRxs Counter
  nb30PortDisInbounds Counter
  nb30PortFwdOutbs Counter
  nb30PortDisLOBs Counter
  nb30PortDisTDEs Counter
  nb30PortCollisions Counter
  nb30PortTxAborts Counter
  nb30PortOowCollisions Counter
  nb30PortCRCErrs Counter
  nb30PortFrAlignErrs Counter
  nb30PortPriority INTEGER
  nb30PortState OCTET STRING
  nb30PortPathCost INTEGER
  nb30PortDesigCost INTEGER
  nb30PortDesigBrdg OCTET STRING
  nb30PortDesigPort INTEGER
  nb30PortTopChgAck INTEGER
  nb30PortDesigRoot OCTET STRING
  nb30PortOversizePkts Counter
  nb30PortFrFiltereds Counter
  nb30PortPollAddress OCTET STRING
  nb30PortPollInterval INTEGER
  nb30PortMaxRetry INTEGER
  nb30PortId INTEGER

Nb30RemPortEntry  
SEQUENCE    
  nb30RemPortName OCTET STRING
  nb30RemPortType OCTET STRING
  nb30RemPortStatus OCTET STRING
  nb30RemPortNetName OCTET STRING
  nb30RemPortFrRxs Counter
  nb30RemPortFwdOutbs Counter
  nb30RemPortDisLOBs Counter
  nb30RemPortDisTDEs Counter
  nb30RemPortCRCErrs Counter
  nb30RemPortFrAlErrs Counter
  nb30RemPortId INTEGER

Nb30AcqDBEntry  
SEQUENCE    
  nb30AcqCreateFilter INTEGER
  nb30AcqCreateForward INTEGER
  nb30AcqDeleteFilter INTEGER
  nb30AcqFilterType OCTET STRING
  nb30AcqFilterAction INTEGER
  nb30AcqSourceAddress OCTET STRING
  nb30AcqMacAddress OCTET STRING

Nb30PermDBEntry  
SEQUENCE    
  nb30PermCreateFilter INTEGER
  nb30PermCreateForward INTEGER
  nb30PermDeleteEntry INTEGER
  nb30PermFilterType OCTET STRING
  nb30PermFilterAction INTEGER
  nb30PermSourceAddress OCTET STRING
  nb30PermDBMacAddress OCTET STRING

Nb30SpecDBEntry  
SEQUENCE    
  nb30SpecEnable INTEGER
  nb30SpecPort1 INTEGER
  nb30SpecDestAddress OCTET STRING
  nb30SpecSrcAddress OCTET STRING
  nb30SpecType OCTET STRING
  nb30SpecDataField OCTET STRING
  nb30SpecDeleteFilter INTEGER
  nb30SpecDbFilterNumber INTEGER

Defined Values

nb30Device 1.3.6.1.4.1.52.1.6.12.1
OBJECT IDENTIFIER    

nb30Dsx 1.3.6.1.4.1.52.1.6.12.2
OBJECT IDENTIFIER    

nb30DsxChannel 1.3.6.1.4.1.52.1.6.12.3
OBJECT IDENTIFIER    

nb30Port 1.3.6.1.4.1.52.1.6.12.4
OBJECT IDENTIFIER    

nb30RemPort 1.3.6.1.4.1.52.1.6.12.5
OBJECT IDENTIFIER    

nb30FilterDB 1.3.6.1.4.1.52.1.6.12.6
OBJECT IDENTIFIER    

nb30AcqDB 1.3.6.1.4.1.52.1.6.12.6.1
OBJECT IDENTIFIER    

nb30PermDB 1.3.6.1.4.1.52.1.6.12.6.2
OBJECT IDENTIFIER    

nb30SpecDB 1.3.6.1.4.1.52.1.6.12.6.3
OBJECT IDENTIFIER    

nb30DeviceDisableBdg 1.3.6.1.4.1.52.1.6.12.1.1
Indicates if the bridge will be disabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disableBridge(2), enableBridge(1)  

nb30DeviceRestoreSettings 1.3.6.1.4.1.52.1.6.12.1.2
Restore the following settings to their default values: Bridge Name to CABLETRON REMOTE BRIDGE, Location to LOCAL, Enet Port 1 Name to ETHERNET PORT 1, Enet Port 2 Name to ETHERNET PORT 2, Remote Port Name to REMOTE PORT, Enet Port 1 Network Name to LAN_1, Enet Port 2 Network Name to LAN_2, Defualt Enet Port to Port 1, Enable Redundancy to NO, Port 1 and Port 2 Poll Address to 00-00-00-00-00-00, Port 1 and Port 2 Poll Interval to 5 Seconds, Port 1 and Port 2 Max Retries to 6, Remote Port Network Name to REMOTE LINK, Ageing Time for Acquired Database to 300 seconds, Place seventeen default multicast addresses into the permanent and acquired databases, Type of Spanning Tree to 802.1, Type of Filtering to IEEE 802.1, Bridge Max Age to 20 seconds, Bridge Forward Delay to 15 seconds, Bridge Hello Time to 2 seconds, Bridge Priority to 8000, Port 1 Priority to 80, Port 2 Priority to 80, Port 1 Path Cost to 1000, Port 2 Path Cost to 1000, Number of Restarts to 0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER restoreSettings(1)  

nb30DeviceBdgName 1.3.6.1.4.1.52.1.6.12.1.3
The user-defined name (up to 32 characters long) of the bridge. The default bridge name is CABLETRON REMOTE BRIDGE.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

nb30DeviceNumPorts 1.3.6.1.4.1.52.1.6.12.1.4
The number of ports present on the bridge.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nb30DeviceType 1.3.6.1.4.1.52.1.6.12.1.5
The type of bridge, NB30.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nb30DeviceVersion 1.3.6.1.4.1.52.1.6.12.1.6
The release version of the firmware installed in the bridge.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nb30DeviceLocation 1.3.6.1.4.1.52.1.6.12.1.7
The user-defined name (up to 14 characters long) to indicate the location of the bridge on the network. The default location name is LOCAL.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

nb30DeviceStatus 1.3.6.1.4.1.52.1.6.12.1.8
The status of the bridge, ON-LINE, STAND BY or DISABLED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nb30DeviceRestartBdg 1.3.6.1.4.1.52.1.6.12.1.9
Force the bridge to undergo a software reset.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER restartBridge(1)  

nb30DeviceFrFwds 1.3.6.1.4.1.52.1.6.12.1.10
The number of frames forwarded by the bridge.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nb30DeviceFrRxs 1.3.6.1.4.1.52.1.6.12.1.11
The number of frames received by the bridge.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nb30DeviceFrFlts 1.3.6.1.4.1.52.1.6.12.1.12
The number of frames filtered by the bridge.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nb30DeviceErrs 1.3.6.1.4.1.52.1.6.12.1.13
The total number of network errors that have occurred.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nb30DeviceNumRestarts 1.3.6.1.4.1.52.1.6.12.1.14
The number of times the bridge has been powered up or restarted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nb30DeviceTypeFiltering 1.3.6.1.4.1.52.1.6.12.1.15
The type of filtering to be performed by the bridge. The default is IEEE 802.1.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ieee8021(1), specialDB(2), both(3)  

nb30DeviceSTAProtocol 1.3.6.1.4.1.52.1.6.12.1.16
The spanning tree algorithm under which the bridge is operating. The selections are as follows: - IEEE 802.1 compliant spanning tree algorithm environment (802.1) - DEC LAN Bridge 100 environment (DEC) - Without the spanning tree algorithm enabled (NONE) The default is 802.1.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ieee8021(1), dec(2), none(3)  

nb30DeviceBridgeID 1.3.6.1.4.1.52.1.6.12.1.17
The unique identifier of the bridge. The first two bytes of the identifier are the bridge priority and the last six bytes are the Ethernet address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nb30DeviceTopChgCnts 1.3.6.1.4.1.52.1.6.12.1.18
The number of times the bridge's Topology Change Flag has been changed since the bridge was powered up or initialized.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nb30DeviceTimeTopChg 1.3.6.1.4.1.52.1.6.12.1.19
The time in seconds that has elapsed since the bridge's Topology Change Flag last recorded the value of a topology change.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nb30DeviceTopChg 1.3.6.1.4.1.52.1.6.12.1.20
Indicates if a bridge topology change is in progress.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER noTopologyChangeInProgress(1), topologyChangeInProgress(2)  

nb30DeviceRootCost 1.3.6.1.4.1.52.1.6.12.1.21
The cost of the path to the root from this bridge.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nb30DeviceRootPort 1.3.6.1.4.1.52.1.6.12.1.22
The port identifier for the port which offers the lowest cost path to the root, i.e. that port for which the sum of the values of the designated cost and path cost parameters held for the port is lowest.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nb30DeviceDesigRoot 1.3.6.1.4.1.52.1.6.12.1.23
The unique identifier of the bridge recorded as the root.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nb30DeviceMaxAge 1.3.6.1.4.1.52.1.6.12.1.24
The maximum age of received protocol information before it is discarded.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nb30DeviceHoldTime 1.3.6.1.4.1.52.1.6.12.1.25
The minimum time period elapsing between the transmission of configuration BPDU's through a given bridge port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nb30DeviceFwdDly 1.3.6.1.4.1.52.1.6.12.1.26
The time spent in the listening state while moving from the blocking state to the learning state, or the time spent in the learning state while moving from the listening state to the forwarding state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nb30DeviceHelloTime 1.3.6.1.4.1.52.1.6.12.1.27
The time interval between the transmission of Configuration BPDU's by a bridge which is attempting to become the root or is the root.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nb30DeviceBdgFwdDly 1.3.6.1.4.1.52.1.6.12.1.28
The value of the forward delay parameter when the bridge is the root or is attempting to become the root. A time of 4 to 30 seconds is allowed. The default is 15 seconds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

nb30DeviceBdgMaxAge 1.3.6.1.4.1.52.1.6.12.1.29
The value of the Max Age parameter when the bridge is the root or is attempting to become the root. A time of 6 to 40 seconds is allowed. The default is 20 seconds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

nb30DeviceBdgHello 1.3.6.1.4.1.52.1.6.12.1.30
The value of the Hello Time parameter when the bridge is the root or is attempting to become the root. A time of 1 to 10 seconds is allowed. The default is 2 seconds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

nb30DeviceBdgPriority 1.3.6.1.4.1.52.1.6.12.1.31
Used in the spanning tree for priority comparisons. Allowed range is 0 through FFFF. The default is 8000.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

nb30DeviceResetCounts 1.3.6.1.4.1.52.1.6.12.1.32
Reset all counters to zero.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER resetCounts(1)  

nb30DeviceUptime 1.3.6.1.4.1.52.1.6.12.1.33
The time, in seconds, that has elapsed since the bridge was last reset or initialized.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nb30DeviceRootSwitch 1.3.6.1.4.1.52.1.6.12.1.34
The status of the Root switch on the front panel of the NB30.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER noRoot(1), root(2)  

nb30DeviceFwdBroadcast 1.3.6.1.4.1.52.1.6.12.1.35
The status of the Forward Broadcast switch on the front panel of the NB30.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER forwardBroadcast(1), filterBroadcast(2)  

nb30DeviceConfigSw1 1.3.6.1.4.1.52.1.6.12.1.36
The status of Config switch 1 on the back panel of the NB30.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER switchOff(1), switchOn(2)  

nb30DeviceConfigSw2 1.3.6.1.4.1.52.1.6.12.1.37
The status of Config switch 2 on the back panel of the NB30.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER switchOff(1), switchOn(2)  

nb30DeviceConfigSw3 1.3.6.1.4.1.52.1.6.12.1.38
The status of Config switch 3 on the back panel of the NB30.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER switchOff(1), switchOn(2)  

nb30DeviceConfigSw4 1.3.6.1.4.1.52.1.6.12.1.39
The status of Config switch 4 on the back panel of the NB30.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER switchOff(1), switchOn(2)  

nb30DevicePortActive 1.3.6.1.4.1.52.1.6.12.1.40
The Port number which is acting as the online Ethernet Port on the NB30.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nb30DeviceDefPort 1.3.6.1.4.1.52.1.6.12.1.41
The Port number which is Default Ethernet Port on the NB30 at power up.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ethernetPort1(1), ethernetPort2(2)  

nb30DeviceRedEnable 1.3.6.1.4.1.52.1.6.12.1.42
The state of the Redundancy Enable Flag.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disableRedundancy(1), enableRedundancy(2)  

nb30DsxLoopUp 1.3.6.1.4.1.52.1.6.12.2.1
The loop up command for the DSX-1 Remote Interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER loopUp(1)  

nb30DsxLoopDn 1.3.6.1.4.1.52.1.6.12.2.2
The loop down command for the DSX-1 Remote Interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER loopDown(1)  

nb30DsxLoopSt 1.3.6.1.4.1.52.1.6.12.2.3
The loop status for the DSX-1 Remote Interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notInLoopback(1), loopbackInProgress(2), networkLoopback(3), loopbackPassed(4), loopbackFailed(5)  

nb30DsxLoopPattern 1.3.6.1.4.1.52.1.6.12.2.4
The loop test pattern for the DSX-1 Remote Interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER alternate1sAnd0s(1), all1s(2), all0s(3), incrementingData(4)  

nb30DsxChannelTable 1.3.6.1.4.1.52.1.6.12.3.1
NB30 DSX-1 Remote Port Channelization Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Nb30DsxEntry

nb30DsxEntry 1.3.6.1.4.1.52.1.6.12.3.1.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Nb30DsxEntry  

nb30DsxChannelControl 1.3.6.1.4.1.52.1.6.12.3.1.1.1
Disable the DSX-1 Channel.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disableChannel(1), enableChannel(2)  

nb30DsxChannelId 1.3.6.1.4.1.52.1.6.12.3.1.1.2
The channel number for this entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

nb30PortTable 1.3.6.1.4.1.52.1.6.12.4.1
Bridge Port information table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Nb30PortEntry

nb30PortEntry 1.3.6.1.4.1.52.1.6.12.4.1.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Nb30PortEntry  

nb30PortAddress 1.3.6.1.4.1.52.1.6.12.4.1.1.1
The Ethernet address of the port. Instance of 1 represents the local Ethernet address, instance of 2 represents the remote Ethernet address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nb30PortName 1.3.6.1.4.1.52.1.6.12.4.1.1.2
The user-defined name (up to 32 characters long) assigned to the port. The default Enet port 1 name is ETHERNET PORT 1 and the default Enet Port 2 name is ETHERNET PORT 2.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

nb30PortType 1.3.6.1.4.1.52.1.6.12.4.1.1.3
The IEEE specification the port meets, e.g. 802.3.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nb30PortStatus 1.3.6.1.4.1.52.1.6.12.4.1.1.4
The status in which the port is operating. The status messages for Ports 1 and 2 are: OFF - The port is off, due to a failed network interface chip associated with that port. OK/SQE ON - The port is communicating with the network and the transceiver making the connection to the network has SQE enabled. OK/SQE OFF - The port is communicating with the network and the transceiver making the connection to the network has SQE disabled. CARRIER LOST - Communication with the network has not been established or has been lost.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nb30PortNetName 1.3.6.1.4.1.52.1.6.12.4.1.1.5
The user-defined name (up to 32 characters long) assigned to a network segment connected to the port. The default network name for Port 1 is LAN_1 and the default network name for Port 2 is LAN_2.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

nb30PortFrRxs 1.3.6.1.4.1.52.1.6.12.4.1.1.6
The number of frames received at the specified port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nb30PortDisInbounds 1.3.6.1.4.1.52.1.6.12.4.1.1.7
The total number of valid frames that were received at the port but then discarded by the bridge in the forwarding process.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nb30PortFwdOutbs 1.3.6.1.4.1.52.1.6.12.4.1.1.8
The number of frames forwarded successfully to the appropriate port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nb30PortDisLOBs 1.3.6.1.4.1.52.1.6.12.4.1.1.9
The number of packets that were discarded by the bridge because of a lack of buffer space to maintain the data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nb30PortDisTDEs 1.3.6.1.4.1.52.1.6.12.4.1.1.10
The number of frames that were intended for forwarding but were discarded when the maximum time period set for transmission was exceeded before forwarding was possible.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nb30PortCollisions 1.3.6.1.4.1.52.1.6.12.4.1.1.11
The number of collisions that have occurred on the network at the specified port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nb30PortTxAborts 1.3.6.1.4.1.52.1.6.12.4.1.1.12
The number of transmissions that have been aborted due to excessive collisions (over 16 attempts to transmit the same packet).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nb30PortOowCollisions 1.3.6.1.4.1.52.1.6.12.4.1.1.13
The number of collisions out of the standard collision window (51.2 uS). This indicates a network problem.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nb30PortCRCErrs 1.3.6.1.4.1.52.1.6.12.4.1.1.14
The number of packets detected with Cyclical Redundancy Check failures.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nb30PortFrAlignErrs 1.3.6.1.4.1.52.1.6.12.4.1.1.15
The number of errors due to misaligned packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nb30PortPriority 1.3.6.1.4.1.52.1.6.12.4.1.1.16
The part of the port identifier which is used with the spanning tree algorithm when determining which port in a LAN segment has priority. The default is 80. Applies to the LOCAL and REMOTE Ethernet ports where instance 1 always refers to the local ethernet port and instance 2 always refers to the remote ethernet port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

nb30PortState 1.3.6.1.4.1.52.1.6.12.4.1.1.17
The current state of the port, DISABLED, LISTENING, LEARNING, FORWARDING or BLOCKING. Applies to the LOCAL and REMOTE Ethernet ports where instance 1 always refers to the local ethernet port and instance 2 always refers to the remote ethernet port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nb30PortPathCost 1.3.6.1.4.1.52.1.6.12.4.1.1.18
The contributory cost of the applicable port to the overall cost of the path when the specified port is the root port. Allowable range is 1 to 65535. The default is 1000. Applies to the LOCAL and REMOTE Ethernet ports where instance 1 always refers to the local ethernet port and instance 2 always refers to the remote ethernet port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

nb30PortDesigCost 1.3.6.1.4.1.52.1.6.12.4.1.1.19
The cost of the path of this port to the root bridge on the network. Applies to the LOCAL and REMOTE Ethernet ports where instance 1 always refers to the local ethernet port and instance 2 always refers to the remote ethernet port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nb30PortDesigBrdg 1.3.6.1.4.1.52.1.6.12.4.1.1.20
The network address of the bridge that is assumed to be the root bridge on the network. Applies to the LOCAL and REMOTE Ethernet ports where instance 1 always refers to the local ethernet port and instance 2 always refers to the remote ethernet port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nb30PortDesigPort 1.3.6.1.4.1.52.1.6.12.4.1.1.21
The port identifier of the bridge port believed to be the designated port for the LAN associated with the port. Applies to the LOCAL and REMOTE Ethernet ports where instance 1 always refers to the local ethernet port and instance 2 always refers to the remote ethernet port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nb30PortTopChgAck 1.3.6.1.4.1.52.1.6.12.4.1.1.22
The value of the topology change acknowledgement flag in the next configuration BPDU to be transmitted on the associated port. Applies to the LOCAL and REMOTE Ethernet ports where instance 1 always refers to the local ethernet port and instance 2 always refers to the remote ethernet port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER noTopologyChangeIsOccurring(1), topologyChangeIsOccurring(2)  

nb30PortDesigRoot 1.3.6.1.4.1.52.1.6.12.4.1.1.23
The unique bridge identifier of the bridge that is assumed to be the root bridge on the network. Applies to the LOCAL and REMOTE Ethernet ports where instance 1 always refers to the local ethernet port and instance 2 always refers to the remote ethernet port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nb30PortOversizePkts 1.3.6.1.4.1.52.1.6.12.4.1.1.24
The number of packets received at the indicated NB30 Port that were greater than the IEEE 802.3 maximum Ethernet frame size of 1518 bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nb30PortFrFiltereds 1.3.6.1.4.1.52.1.6.12.4.1.1.25
The number of frames received at the indicated port that were filtered by the bridge.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nb30PortPollAddress 1.3.6.1.4.1.52.1.6.12.4.1.1.26
The Poll Address that will be used by the Redundant Port Algorithm on the NB30.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

nb30PortPollInterval 1.3.6.1.4.1.52.1.6.12.4.1.1.27
The Poll Interval used by the Redundant Port Algorithm on the NB30. Valid range is 1 - 30 seconds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

nb30PortMaxRetry 1.3.6.1.4.1.52.1.6.12.4.1.1.28
The Max number of retries for the Redundant Port Algorithm on the NB30. Valid range is 2 - 99 retries
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

nb30PortId 1.3.6.1.4.1.52.1.6.12.4.1.1.29
The port number for this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nb30RemPortTable 1.3.6.1.4.1.52.1.6.12.5.1
Bridge Remote Port information table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Nb30RemPortEntry

nb30RemPortEntry 1.3.6.1.4.1.52.1.6.12.5.1.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Nb30RemPortEntry  

nb30RemPortName 1.3.6.1.4.1.52.1.6.12.5.1.1.1
The user-defined name assigned to the remote port. The default Remote port name is REMOTE PORT.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

nb30RemPortType 1.3.6.1.4.1.52.1.6.12.5.1.1.2
The Electrical interface specification the port meets, e.g. DSX-1, V.35.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nb30RemPortStatus 1.3.6.1.4.1.52.1.6.12.5.1.1.3
The status in which the remote port is operating. The status messages for the Remote Port are: NO EXT CLOCK DCE NOT READY / NO DM DCE NOT READY / NO CTS LINK OK / DCE READY NET LOOP / RED ALARM REM LOOP / RED ALARM NORMAL / RED ALARM NET LOOP / YELLOW ALARM REM LOOP / YELLOW ALARM NORMAL / YELLOW ALARM NET LOOP / LINK OK REM LOOP / LINK OK NORMAL / LINK OK NET LOOP / LINK LOST REM LOOP / LINK LOST NORMAL / LINK LOST
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nb30RemPortNetName 1.3.6.1.4.1.52.1.6.12.5.1.1.4
The user-defined name assigned to a wide area segment connected to the remote port. The default network name for Remote Port is REMOTE LINK.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

nb30RemPortFrRxs 1.3.6.1.4.1.52.1.6.12.5.1.1.5
The number of frames received at the remote port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nb30RemPortFwdOutbs 1.3.6.1.4.1.52.1.6.12.5.1.1.6
The number of frames forwarded successfully to the remote port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nb30RemPortDisLOBs 1.3.6.1.4.1.52.1.6.12.5.1.1.7
The number of packets that were discarded by the bridge because of a lack of buffer space to maintain the data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nb30RemPortDisTDEs 1.3.6.1.4.1.52.1.6.12.5.1.1.8
The number of frames that were intended for forwarding but were discarded when the maximum time period set for transmission was exceeded before forwarding was possible.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nb30RemPortCRCErrs 1.3.6.1.4.1.52.1.6.12.5.1.1.9
The number of packets detected with Cyclical Redundancy Check failures.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nb30RemPortFrAlErrs 1.3.6.1.4.1.52.1.6.12.5.1.1.10
The number of errors due to misaligned packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nb30RemPortId 1.3.6.1.4.1.52.1.6.12.5.1.1.11
The remote port ID, there is only a single port which is identified as 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nb30AcqTotalEntries 1.3.6.1.4.1.52.1.6.12.6.1.1
The total number of entries in the acquired database.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nb30AcqMaxEntries 1.3.6.1.4.1.52.1.6.12.6.1.2
The maximum number of entries allowed in the acquired database 8191 entries.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nb30AcqStaticEntries 1.3.6.1.4.1.52.1.6.12.6.1.3
The number of addresses added to the Acquired database by the user or network manager.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nb30AcqDynamicEntries 1.3.6.1.4.1.52.1.6.12.6.1.4
The number of entries that have been accumulated in the Acquired database through the bridge's learning process.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nb30AcqDynAgeTime 1.3.6.1.4.1.52.1.6.12.6.1.5
The length of time allowed for a dynamic entry in the acquired database to be inactive before it is dropped from the database. A time from 10 - 1,000,000 seconds is allowed. The default is 300 seconds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

nb30AcqEraseDatabase 1.3.6.1.4.1.52.1.6.12.6.1.6
Set to one to erase all entries in the acquired database.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER eraseAcquiredDatabase(1)  

nb30AcqDBTable 1.3.6.1.4.1.52.1.6.12.6.1.7
Aquired database entrys table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Nb30AcqDBEntry

nb30AcqDBEntry 1.3.6.1.4.1.52.1.6.12.6.1.7.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Nb30AcqDBEntry  

nb30AcqCreateFilter 1.3.6.1.4.1.52.1.6.12.6.1.7.1.1
Add an entry to the acquired database to filter packets entering port 1 if those packets are destined for the specified address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER createAcquiredFilter(1)  

nb30AcqCreateForward 1.3.6.1.4.1.52.1.6.12.6.1.7.1.2
Add an entry to the acquired database to forward packets entering port 1 to the remote port if those packets are destined for the specified address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER createAcquiredForward(1)  

nb30AcqDeleteFilter 1.3.6.1.4.1.52.1.6.12.6.1.7.1.3
Delete an entry from the acquired database.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER deleteAcquiredEntry(1)  

nb30AcqFilterType 1.3.6.1.4.1.52.1.6.12.6.1.7.1.4
Display the entry type, STATIC or DYNAMIC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nb30AcqFilterAction 1.3.6.1.4.1.52.1.6.12.6.1.7.1.5
The action to be taken for packets entering port 1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER filter(1), relay(2)  

nb30AcqSourceAddress 1.3.6.1.4.1.52.1.6.12.6.1.7.1.6
The source address of this acquired database entry, i.e. the instance.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nb30AcqMacAddress 1.3.6.1.4.1.52.1.6.12.6.1.7.1.7
The MAC address for the specific entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(6)  

nb30PermMaxEntries 1.3.6.1.4.1.52.1.6.12.6.2.1
The maximum number of entries allowed in the permanent database 2047 entries.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nb30PermCurrentEntries 1.3.6.1.4.1.52.1.6.12.6.2.2
The number of entries currently recorded in the bridge's permanent database.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nb30PermEraseDatabase 1.3.6.1.4.1.52.1.6.12.6.2.3
Erase all entries in the permanent database.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER erasePermanentDatabase(1)  

nb30PermDBTable 1.3.6.1.4.1.52.1.6.12.6.2.4
Aquired database entrys table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Nb30PermDBEntry

nb30PermDBEntry 1.3.6.1.4.1.52.1.6.12.6.2.4.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Nb30PermDBEntry  

nb30PermCreateFilter 1.3.6.1.4.1.52.1.6.12.6.2.4.1.1
Add an entry to the permanent database to filter packets entering port 1 if those packets are destined for the specified address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER createPermanentFilter(1)  

nb30PermCreateForward 1.3.6.1.4.1.52.1.6.12.6.2.4.1.2
Add an entry to the permanent database to forward packets entering port 1 to the remote port if those packets are destined for the specified address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER createPermanentForward(1)  

nb30PermDeleteEntry 1.3.6.1.4.1.52.1.6.12.6.2.4.1.3
Delete an entry from the permanent database.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER deletePermanentEntry(1)  

nb30PermFilterType 1.3.6.1.4.1.52.1.6.12.6.2.4.1.4
Display the entry type, STATIC .
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nb30PermFilterAction 1.3.6.1.4.1.52.1.6.12.6.2.4.1.5
The action taken on packets entering port 1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER filter(1), relay(2)  

nb30PermSourceAddress 1.3.6.1.4.1.52.1.6.12.6.2.4.1.6
The source address in this permanent database entry, i.e. the instance.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nb30PermDBMacAddress 1.3.6.1.4.1.52.1.6.12.6.2.4.1.7
The specific MAC address for this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(6)  

nb30SpecNumEntries 1.3.6.1.4.1.52.1.6.12.6.3.1
The number of filters in the special database.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nb30SpecMaxEntries 1.3.6.1.4.1.52.1.6.12.6.3.2
The maximum number of filters the special database can contain.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nb30SpecNextFilterNum 1.3.6.1.4.1.52.1.6.12.6.3.3
The number of the next available filter that can be added to the special database. This OID will return a 255 if the database is full
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nb30SpecDBTable 1.3.6.1.4.1.52.1.6.12.6.3.4
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Nb30SpecDBEntry

nb30SpecDBEntry 1.3.6.1.4.1.52.1.6.12.6.3.4.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Nb30SpecDBEntry  

nb30SpecEnable 1.3.6.1.4.1.52.1.6.12.6.3.4.1.1
Enable or disable the filter.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disableFilter(1), enableFilter(2)  

nb30SpecPort1 1.3.6.1.4.1.52.1.6.12.6.3.4.1.2
Set port 1 to filter or forward packets.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER filter(1), relay(2)  

nb30SpecDestAddress 1.3.6.1.4.1.52.1.6.12.6.3.4.1.3
Set the special database to filter packets with a specific destination address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

nb30SpecSrcAddress 1.3.6.1.4.1.52.1.6.12.6.3.4.1.4
Set the special database to filter packets with a specific source address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

nb30SpecType 1.3.6.1.4.1.52.1.6.12.6.3.4.1.5
Set the special database to filter packets with a specific type field.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

nb30SpecDataField 1.3.6.1.4.1.52.1.6.12.6.3.4.1.6
Set the special database to filter packets based on the first sixteen bytes of data in the packet.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

nb30SpecDeleteFilter 1.3.6.1.4.1.52.1.6.12.6.3.4.1.7
Delete a filter from the special database.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER deleteFilter(1)  

nb30SpecDbFilterNumber 1.3.6.1.4.1.52.1.6.12.6.3.4.1.8
The specific special data base filter number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER