MWRM-UNIT-MIB

File: MWRM-UNIT-MIB.mib (212968 bytes)

Imported modules

SNMPv2-SMI RFC1213-MIB SNMPv2-TC
RFC-1215

Imported symbols

Counter64 enterprises IpAddress
DisplayString ifIndex RowStatus
MacAddress OBJECT-TYPE TRAP-TYPE

Defined Types

EnableDisable  
INTEGER enable(2), disable(3)    

EnableDisableSMI2  
INTEGER disable(0), enable(1)    

OffOn  
INTEGER off(0), on(1)    

MetricImperial  
INTEGER metric(0), imperial(1)    

AllowedNotAllowed  
INTEGER not-allowed(0), allowed(1)    

NoYes  
INTEGER no(0), yes(1)    

DownUp  
INTEGER down(0), up(1)    

SupportedNotsupported  
INTEGER supported(2), not-supported(3)    

ProgressStatus  
INTEGER ready(0), inProgress(1), success(2), failure(3)    

Severity  
INTEGER indeterminate(0), critical(1), major(2), minor(3), warning(4), cleared(5)    

TrailIfType  
INTEGER unknown(-1), line(0), radio(1), stm-1-oc-3(2), sync(4)    

PmTableType  
INTEGER pm15mincurr(1), pm15min(2), pm24hrcurr(3), pm24hr(4)    

RateMbps  
INTEGER not-applicable(-1), n10(0), n100(1), n1000(2)    

HalfFull  
INTEGER not-applicable(-1), half(0), full(1), auto(2)    

BerLevel  
INTEGER n1e-3(2), n1e-4(3), n1e-5(4)    

SignalLevel  
INTEGER n1e-6(5), n1e-7(6), n1e-8(7), n1e-9(8)    

Exponent  
INTEGER n1e-2(1), n1e-3(2), n1e-4(3), n1e-5(4), n1e-6(5), n1e-7(6), n1e-8(7), n1e-9(8), n1e-10(9), n1e-11(10), n1e-12(11), n1e-13(12), n1e-14(13), n1e-15(14), n1e-16(15), n1e-17(16), n1e-18(17), n1e-0(18)    

LoopbackType  
INTEGER off(0), towardsLine(1), towardsRadio(2)    

QueueName  
INTEGER first-queue(0), second-queue(1), third-queue(2), fourth-queue(3), none(4)    

RadioId  
INTEGER    

RfuId  
INTEGER    

SwCommand  
INTEGER noOperation(0), downloadUpgradeVersion(1), upgrade(2), rollback(3), downgrade(4), downloadDowngradeVersion(5)    

TrailProtectedType  
INTEGER none(0), primary(1), secondary(2)    

ClockSrc  
INTEGER local-clock(0), system-clock-source(1)    

SlotId  
INTEGER standalone(0), slot1(1), slot2(2), slot3(3), slot4(4), slot5(5), slot6(6), slot7(7), slot8(8), slot9(9), slot10(10), slot11(11), slot12(12)    

Integrity  
INTEGER integrity(0), nointegrity(1)    

GreenYellow  
INTEGER green(0), yellow(1)    

InputSeverity  
INTEGER indeterminate(0), critical(1), major(2), minor(3), warning(4)    

SwCommandTimer  
INTEGER noOperation(0), downloadUpgradeVersion(1), upgrade(2), rollback(3), downgrade(4), downloadDowngradeVersion(5), upgradeTimer(6), rollbackTimer(7), downgradeTimer(8), abortTimedInstallation(9)    

FileTransferStatus  
INTEGER ready(0), inTransfer(1), failure(2), success(3)    

FileRestoreStatus  
INTEGER ready(0), restoring-configuration(1), failure(2), success(3)    

RbacAccessLevel  
INTEGER none(0), normal(1), advance(2)    

InventoryCardType  
INTEGER cleared(0), nexusSc(10), nexusScLp(11), nexusDc(12), nexusQc(13), tccR(19), tccA(20), tccB(21), rmcA(22), rmcB(23), rmcNDc(24), nativeTdm16xE1T1(25), pwe3-16xE1T1(26), tdm1xStm1(27), tdm1xOc3(28), eLicEth4x1GEA(29), chassis1U2U(30), capacityBooster(31), pwe3-1xSTM1(32), pdc48v2uSingleFeed(33), pdc48v1uSingleFeed(34), pdc48v1uDualFeed(35), fan2U(36), fan1U(37), test-card(38), pdc24v2uSingleFeed(39), pdc24v1uSingleFeed(40), pdc24v1uDualFeed(41), unknownCard(42), ricE(43), trafficFpga(44), essFpga(45), tressFpga(46), ip20g(47), licXe4opt(48), tccBmc(49), rmcE(50), licStm1oc3rst(51), tccAmc(52), ip20cEband(53), tccA2(54), tccA2mc(55), tccB2(56)    

FtpProtocolType  
INTEGER ftp(0), sftp(1)    

CfgUnitInfoOper  
INTEGER invalid-operation(0), create-pakcge(1), export-pakcge(2)    

CfgOper  
INTEGER invalid-operation(0), backup(1), restore(2), delete(3), import(4), export(5)    

CardOccupancy  
INTEGER empty(1), equipped(2), not-operational(3)    

OperState  
INTEGER down(1), init(2), loading(3), loaded(4), up(5), up-with-alarms(6)    

LicenseGeneric  
INTEGER not-allowed(100000), allowed(100001), disable(100010), enable(100011), only-management(100020), smart-pipe(100021), enhanced-pipe(100022), edge-cet(100023), access-cet(100024), aggregation-cet(100025)    

RaduisAcceaaLevel  
INTEGER none(0), normal(1), advanced(2), root(3)    

VmResetType  
INTEGER no-reset(0), main-board-warm-reset(1), tcc-cold-reset(2), main-board-cold-reset(3), card-warm-reset(4), card-cold-reset(5), not-applicable-reset(6)    

FTStatus  
INTEGER ready(0), file-in-transfer(1), failure(2), success(3)    

CsrCertificateFTState  
INTEGER no-operation(0), upload(1), download(2)    

CsrFileFormat  
INTEGER pem(1), der(2)    

GenEquipUnitInfoTimeServicesEntry  
SEQUENCE    
  genEquipUnitInfoTimeServicesIndex INTEGER
  genEquipUnitInfoTimeServicesUtcHours INTEGER
  genEquipUnitInfoTimeServicesUtcMinutes INTEGER
  genEquipUnitInfoTimeServicesDstStartMonth INTEGER
  genEquipUnitInfoTimeServicesDstStartDay INTEGER
  genEquipUnitInfoTimeServicesDstEndMonth INTEGER
  genEquipUnitInfoTimeServicesDstEndDay INTEGER
  genEquipUnitInfoTimeServicesDstOffset INTEGER
  genEquipUnitInfoTimeServicesUtcDateAndTime INTEGER
  genEquipUnitInfoTimeServicesUtcCurrentDateAndTime INTEGER

GenEquipUnitInfoNtpStatusEntry  
SEQUENCE    
  genEquipUnitInfoNtpStatusIndex INTEGER
  genEquipUnitInfoNtpStatusPollInterval INTEGER
  genEquipUnitInfoNtpStatusSyncServerIP IpAddress
  genEquipUnitInfoNtpStatusLockState INTEGER

GenEquipUnitInfoNtpConfigEntry  
SEQUENCE    
  genEquipUnitInfoNtpConfigIndex INTEGER
  genEquipUnitInfoNtpConfigAdmin EnableDisable
  genEquipUnitInfoNtpConfigVersion INTEGER
  genEquipUnitInfoNtpConfigServerIPaddress1 IpAddress
  genEquipUnitInfoNtpConfigServerIPaddress2 IpAddress

GenEquipInventoryEntry  
SEQUENCE    
  genEquipInventorySlotIndex INTEGER
  genEquipInventoryCardName DisplayString
  genEquipInventoryCardType InventoryCardType
  genEquipInventoryCardSubType INTEGER
  genEquipInventoryPartNumber DisplayString
  genEquipInventorySerialNumber DisplayString
  genEquipInventoryNumberWorkingDays INTEGER

GenEquipUnitLicenseFeatureEntry  
SEQUENCE    
  genEquipUnitLicenseFeatureId INTEGER
  genEquipUnitLicenseFeatureName DisplayString
  genEquipUnitLicenseFeatureDescription DisplayString
  genEquipUnitLicenseFeatureIsUsed LicenseGeneric
  genEquipUnitLicenseFeatureIsAllowed LicenseGeneric
  genEquipUnitLicenseViolationStatus INTEGER

GenEquipUnitAlarmInputEntry  
SEQUENCE    
  genEquipUnitAlarmInputCounter INTEGER
  genEquipUnitAlarmInputAdmin EnableDisableSMI2
  genEquipUnitAlarmInputText DisplayString
  genEquipUnitAlarmInputSeverity InputSeverity
  genEquipUnitAlarmInputState OffOn

GenEquipUnitAlarmOutputEntry  
SEQUENCE    
  genEquipUnitAlarmOutputCounter INTEGER
  genEquipUnitAlarmOutputAdmin INTEGER
  genEquipUnitAlarmOutputStatus INTEGER
  genEquipUnitAlarmOutputGroup INTEGER

GenEquipUnitShelfManagmentEntry  
SEQUENCE    
  genEquipUnitShelfManagmentSlot SlotId
  genEquipUnitShelfManagmentSlotPopulation INTEGER
  genEquipUnitShelfManagmentCommunicationStatus INTEGER
  genEquipUnitShelfManagmentSlotMostSevereAlarm Severity
  genEquipUnitShelfManagmentMngSwCommand SwCommand
  genEquipUnitShelfManagmentSlotReset OffOn
  genEquipUnitShelfManagmentSlotIp IpAddress

GenEquipUnitShelfSlotConfigEntry  
SEQUENCE    
  genEquipUnitShelfSlotConfigSlotID SlotId
  genEquipUnitShelfSlotConfigExpectedCardType InventoryCardType
  genEquipUnitShelfSlotConfigLabel DisplayString
  genEquipUnitShelfSlotConfigAdmin EnableDisable
  genEquipUnitShelfSlotConfigSlotReset OffOn

GenEquipUnitShelfTccConfigEntry  
SEQUENCE    
  genEquipUnitShelfTccConfigSlotID SlotId
  genEquipUnitShelfTccConfigExpectedCardType InventoryCardType
  genEquipUnitShelfTccConfigLabel DisplayString
  genEquipUnitShelfTccConfigAdmin EnableDisable
  genEquipUnitShelfTccConfigReset OffOn

GenEquipUnitShelfSlotStatusEntry  
SEQUENCE    
  genEquipUnitShelfSlotStatusSlotID SlotId
  genEquipUnitShelfSlotStatusOccupancy CardOccupancy
  genEquipUnitShelfSlotStatusAllowedCardTypes Counter64
  genEquipUnitShelfSlotStatusCardType InventoryCardType
  genEquipUnitShelfSlotStatusOperationalState OperState
  genEquipUnitShelfSlotStatusCommunication DownUp

GenEquipUnitShelfTccStatusEntry  
SEQUENCE    
  genEquipUnitShelfTccStatusSlotID SlotId
  genEquipUnitShelfTccStatusOccupancy CardOccupancy
  genEquipUnitShelfTccStatusAllowedCardTypes Counter64
  genEquipUnitShelfTccStatusCardType InventoryCardType
  genEquipUnitShelfTccStatusOperationalState OperState
  genEquipUnitShelfTccStatusCommunication DownUp

GenEquipUnitShelfManagmentSeverityEntry  
SEQUENCE    
  genEquipUnitShelfManagmentSeveritySlot INTEGER
  genEquipUnitShelfManagmentSeverityCritical INTEGER
  genEquipUnitShelfManagmentSeverityMajor INTEGER
  genEquipUnitShelfManagmentSeverityMinor INTEGER
  genEquipUnitShelfManagmentSeverityWarning INTEGER
  genEquipUnitShelfManagmentSeverityIndeterminate INTEGER

GenEquipUnitShelfPdcFanStatusEntry  
SEQUENCE    
  genEquipUnitShelfPdcFanStatusPdcFanId INTEGER
  genEquipUnitShelfPdcFanStatusPdcFanExMonitor EnableDisable
  genEquipUnitShelfPdcFanStatusPdcFanOccupancy CardOccupancy
  genEquipUnitShelfPdcFanStatusPdcFanCardType InventoryCardType

GenEquipUnitShelfAbcMuxEntry  
SEQUENCE    
  genEquipUnitShelfAbcMuxNumber INTEGER
  genEquipUnitShelfAbcMuxAdmin EnableDisable

GenEquipCurrentAlarmEntry  
SEQUENCE    
  genEquipCurrentAlarmCounter INTEGER
  genEquipCurrentAlarmRaisedTimeT INTEGER
  genEquipCurrentAlarmId INTEGER
  genEquipCurrentAlarmName DisplayString
  genEquipCurrentAlarmInstance INTEGER
  genEquipCurrentAlarmSeverity Severity
  genEquipCurrentAlarmIfIndex INTEGER
  genEquipCurrentAlarmModule DisplayString
  genEquipCurrentAlarmDesc DisplayString
  genEquipCurrentAlarmProbableCause DisplayString
  genEquipCurrentAlarmCorrectiveActions DisplayString
  genEquipCurrentAlarmState INTEGER
  genEquipCurrentAlarmSlotId INTEGER
  genEquipCurrentAlarmAdditionalInfo DisplayString
  genEquipCurrentAlarmUserText DisplayString

GenEquipAlarmConfigEntry  
SEQUENCE    
  genEquipAlarmConfigId INTEGER
  genEquipAlarmConfigSeverity Severity
  genEquipAlarmConfigDescr DisplayString
  genEquipAlarmConfigAdditionalText DisplayString
  genEquipAlarmServiceAffect OffOn

GenEquipTrapCfgMgrEntry  
SEQUENCE    
  genEquipTrapCfgMgrId INTEGER
  genEquipTrapCfgMgrAdmin EnableDisable
  genEquipTrapCfgMgrIP IpAddress
  genEquipTrapCfgMgrPort INTEGER
  genEquipTrapCfgMgrName DisplayString
  genEquipTrapCfgMgrCommunity DisplayString
  genEquipTrapCfgMgrSeverityFilter INTEGER
  genEquipTrapCfgMgrStatusChangeFilter OffOn
  genEquipTrapCfgMgrCLLI DisplayString
  genEquipTrapCfgMgrHeartbeatPeriod INTEGER
  genEquipTrapCfgMgrIPv6 OCTET STRING
  genEquipTrapCfgMgrV3User DisplayString

GenEquipEventLogEntry  
SEQUENCE    
  genEquipEventLogCounter INTEGER
  genEquipEventLogRaisedTimeT INTEGER
  genEquipEventLogSeverity Severity
  genEquipEventLogModule DisplayString
  genEquipEventLogDesc DisplayString
  genEquipEventLogState INTEGER
  genEquipEventLogProbableCause DisplayString
  genEquipEventLogCorrectiveActions DisplayString
  genEquipEventLogAdditionalInfo DisplayString
  genEquipEventLogUserText DisplayString
  genEquipEventLogIfIndex INTEGER
  genEquipEventLogId INTEGER

GenEquipMngSwIDUVersionsEntry  
SEQUENCE    
  genEquipMngSwIDUVersionsCounter INTEGER
  genEquipMngSwIDUVersionsPackageName DisplayString
  genEquipMngSwIDUVersionsTargetDevice DisplayString
  genEquipMngSwIDUVersionsRunningVersion DisplayString
  genEquipMngSwIDUVersionsInstalledVersion DisplayString
  genEquipMngSwIDUVersionsUpgradePackage DisplayString
  genEquipMngSwIDUVersionsDowngradePackage DisplayString
  genEquipMngSwIDUVersionsResetType INTEGER

GenEquipMngSwTimerEntry  
SEQUENCE    
  genEquipMngSwTimerSlotNumber INTEGER
  genEquipMngSwTimerInstallationTimer INTEGER
  genEquipMngSwTimerTimeToInstall INTEGER
  genEquipMngSwTimerTimerAbort INTEGER

GenEquipMngSwFileTransferEntry  
SEQUENCE    
  genEquipMngSwFileTransferIndex INTEGER
  genEquipMngSwFileTransferProtocol FtpProtocolType
  genEquipMngSwFileTransferUserName DisplayString
  genEquipMngSwFileTransferPassword DisplayString
  genEquipMngSwFileTransferAddress IpAddress
  genEquipMngSwFileTransferPath DisplayString
  genEquipMngSwFileTransferIpv6Address OCTET STRING

GenEquipTrafficCryptoConfigEntry  
SEQUENCE    
  genEquipTrafficCryptoConfigId INTEGER
  genEquipTrafficCryptoConfigConfigAdmin INTEGER
  genEquipTrafficCryptoConfigMkey OCTET STRING
  genEquipTrafficCryptoConfigBackupMkey OCTET STRING
  genEquipTrafficCryptoConfigMkeyPeriod INTEGER
  genEquipTrafficCryptoConfigRandKeyGen INTEGER
  genEquipTrafficCryptoConfigSkeyPeriod INTEGER

GenEquipTrafficCryptoStatusEntry  
SEQUENCE    
  genEquipTrafficCryptoStatusId INTEGER
  genEquipTrafficCryptoStatusValid INTEGER
  genEquipTrafficCryptoStatusMkeyTimeExpire INTEGER

GenEquipMngSwFileTransferStatusEntry  
SEQUENCE    
  genEquipMngSwFileTransferStatusIndex INTEGER
  genEquipMngSwFileTransferStatusResult INTEGER
  genEquipMngSwFileTransferPercentageDone INTEGER
  genEquipMngSwFileTransferPercentageDoneStandBy INTEGER
  genEquipMngSwFileTransferStatusResultStandBy INTEGER

GenEquipMngSwInstallStatusEntry  
SEQUENCE    
  genEquipMngSwInstallStatusIndex INTEGER
  genEquipMngSwInstallStatusResult INTEGER
  genEquipMngSwInstallPercentageDone INTEGER
  genEquipMngSwInstallStatusResultStandBy INTEGER
  genEquipMngSwInstallPercentageDoneStandBy INTEGER

GenEquipMngSwOperationEntry  
SEQUENCE    
  genEquipMngSwOperationIndex INTEGER
  genEquipMngSwOperationOperation INTEGER
  genEquipMngSwOperationTimedInstallation NoYes

GenEquipMngSwSlotRunningVersionEntry  
SEQUENCE    
  genEquipMngSwSlotRunningVersionSlotId INTEGER
  genEquipMngSwSlotRunningVersionCardType InventoryCardType
  genEquipMngSwSlotRunningVersionComponent DisplayString
  genEquipMngSwSlotRunningVersionActualVersion DisplayString

GenEquipMngSwIDUVersionsStandByEntry  
SEQUENCE    
  genEquipMngSwIDUVersionsStandByIndex INTEGER
  genEquipMngSwIDUVersionsStandByPackageName DisplayString
  genEquipMngSwIDUVersionsStandByRunningVersion DisplayString
  genEquipMngSwIDUVersionsStandByInstalledVersion DisplayString
  genEquipMngSwIDUVersionsStandByTargetDevice InventoryCardType
  genEquipMngSwIDUVersionsStandByDownloadedPackage DisplayString
  genEquipMngSwIDUVersionsStandByResetType VmResetType

GenEquipMngCfgFileTransferEntry  
SEQUENCE    
  genEquipMngCfgFileTransferIndex INTEGER
  genEquipMngCfgFileTransferProtocol FtpProtocolType
  genEquipMngCfgFileTransferUserName DisplayString
  genEquipMngCfgFileTransferPassword DisplayString
  genEquipMngCfgFileTransferAddress IpAddress
  genEquipMngCfgFileTransferPath DisplayString
  genEquipMngCfgFileTransferFileName DisplayString
  genEquipMngCfgFileTransferIpv6Address OCTET STRING

GenEquipMngCfgFileTransferStatusEntry  
SEQUENCE    
  genEquipMngCfgFileTransferStatusIndex INTEGER
  genEquipMngCfgFileTransferStatusPercentageDone INTEGER
  genEquipMngCfgFileTransferStatusResult FileTransferStatus

GenEquipMngCfgOperationEntry  
SEQUENCE    
  genEquipMngCfgOperationIndex INTEGER
  genEquipMngCfgOperationOperation CfgOper
  genEquipMngCfgOperationFileNumber INTEGER
  genEquipMngCfgOperationTimedInstallation NoYes
  genEquipMngCfgOperationTimer DisplayString
  genEquipMngCfgOperationSlotNumber INTEGER

GenEquipMngCfgConfigurationFilesEntry  
SEQUENCE    
  genEquipMngCfgConfigurationFilesIndex INTEGER
  genEquipMngCfgConfigurationFilesFileNumber INTEGER
  genEquipMngCfgConfigurationFilesSystemType DisplayString
  genEquipMngCfgConfigurationFilesSWVersion DisplayString
  genEquipMngCfgConfigurationFilesTimeDate INTEGER
  genEquipMngCfgConfigurationFilesSystemIP IpAddress
  genEquipMngCfgConfigurationFilesCardsConfigured DisplayString
  genEquipMngCfgConfigurationFilesSystemID DisplayString

GenEquipMngUnitInfoFileTransferEntry  
SEQUENCE    
  genEquipMngUnitInfoFileTransferIndex INTEGER
  genEquipMngUnitInfoFileTransferProtocol FtpProtocolType
  genEquipMngUnitInfoFileTransferUserName DisplayString
  genEquipMngUnitInfoFileTransferPassword DisplayString
  genEquipMngUnitInfoFileTransferAddress IpAddress
  genEquipMngUnitInfoFileTransferPath DisplayString
  genEquipMngUnitInfoFileTransferFileName DisplayString
  genEquipMngUnitInfoFileTransferIpv6Address OCTET STRING

GenEquipMngUnitInfoFileTransferStatusEntry  
SEQUENCE    
  genEquipMngUnitInfoFileTransferStatusIndex INTEGER
  genEquipMngUnitInfoFileTransferStatusPercentageDone INTEGER
  genEquipMngUnitInfoFileTransferStatusResult ProgressStatus

GenEquipSecurityUsersEntry  
SEQUENCE    
  genEquipSecurityUsersName DisplayString
  genEquipSecurityUsersPasswd DisplayString
  genEquipSecurityUsersPriviledge INTEGER
  genEquipSecurityUsersPasswdAging INTEGER
  genEquipSecurityUsersExprDate INTEGER
  genEquipSecurityUsersLastLogin INTEGER
  genEquipSecurityUsersRowStatus RowStatus

GenEquipSecuritySNMPV3AuthEntry  
SEQUENCE    
  genEquipSecuritySNMPV3AuthUserName DisplayString
  genEquipSecuritySNMPV3AuthPassword DisplayString
  genEquipSecuritySNMPV3AuthSecurityMode INTEGER
  genEquipSecuritySNMPV3AuthEncryptionMode INTEGER
  genEquipSecuritySNMPV3AuthAuthenticationAlgorithm INTEGER
  genEquipSecuritySNMPV3AuthAccessMode INTEGER
  genEquipSecuritySNMPV3AuthRowStatus RowStatus

GenEquipSecurityGenFTConfigEntry  
SEQUENCE    
  genEquipSecurityGenFTConfigIndex INTEGER
  genEquipSecurityGenFTConfigProtocol INTEGER
  genEquipSecurityGenFTConfigUsername DisplayString
  genEquipSecurityGenFTConfigPassword DisplayString
  genEquipSecurityGenFTConfigAddress IpAddress
  genEquipSecurityGenFTConfigFilePath DisplayString
  genEquipSecurityGenFTConfigFileName DisplayString
  genEquipSecurityGenFTConfigIpV6Address OCTET STRING

GenEquipSecurityGenFTStatusEntry  
SEQUENCE    
  genEquipSecurityGenFTStatusIndex INTEGER
  genEquipSecurityGenFTStatusStatus INTEGER
  genEquipSecurityGenFTStatusProgress INTEGER

GenEquipSecurityAccessControlProfileEntry  
SEQUENCE    
  genEquipSecurityAccessControlProfileName DisplayString
  genEquipSecurityAccessControlProfileChannel INTEGER
  genEquipSecurityAccessControlProfileUsed INTEGER
  genEquipSecurityAccessControlProfileSecurityWrite RbacAccessLevel
  genEquipSecurityAccessControlProfileSecurityRead RbacAccessLevel
  genEquipSecurityAccessControlProfileMngWrite RbacAccessLevel
  genEquipSecurityAccessControlProfileMngRead RbacAccessLevel
  genEquipSecurityAccessControlProfileRadioWrite RbacAccessLevel
  genEquipSecurityAccessControlProfileRadioRead RbacAccessLevel
  genEquipSecurityAccessControlProfileTDMWrite RbacAccessLevel
  genEquipSecurityAccessControlProfileTDMRead RbacAccessLevel
  genEquipSecurityAccessControlProfileEthWrite RbacAccessLevel
  genEquipSecurityAccessControlProfileEthRead RbacAccessLevel
  genEquipSecurityAccessControlProfileSyncWrite RbacAccessLevel
  genEquipSecurityAccessControlProfileSyncRead RbacAccessLevel
  genEquipSecurityAccessControlProfileRowStatus RowStatus

GenEquipSecurityAccessControlUserEntry  
SEQUENCE    
  genEquipSecurityAccessControlUserName DisplayString
  genEquipSecurityAccessControlUserProfile DisplayString
  genEquipSecurityAccessControlUserPassword DisplayString
  genEquipSecurityAccessControlUserExpired INTEGER
  genEquipSecurityAccessControlUserBlock NoYes
  genEquipSecurityAccessControlUserLastLogout INTEGER
  genEquipSecurityAccessControlUserLoggedIn NoYes
  genEquipSecurityAccessControlUserRowStatus RowStatus

GenEquipSecurityConfigLogUploadConfigEntry  
SEQUENCE    
  genEquipSecurityConfigLogUploadConfigIndex INTEGER
  genEquipSecurityConfigLogUploadConfigProtocol FtpProtocolType
  genEquipSecurityConfigLogUploadConfigUsername DisplayString
  genEquipSecurityConfigLogUploadConfigPassword DisplayString
  genEquipSecurityConfigLogUploadConfigIpaddress IpAddress
  genEquipSecurityConfigLogUploadConfigPath DisplayString
  genEquipSecurityConfigLogUploadConfigFilename DisplayString
  genEquipSecurityConfigLogUploadConfigIpV6Address OCTET STRING

GenEquipSecurityConfigLogUploadStatusEntry  
SEQUENCE    
  genEquipSecurityConfigLogUploadStatusIndex INTEGER
  genEquipSecurityConfigLogUploadStatusStatus FileTransferStatus
  genEquipSecurityConfigLogUploadStatusPrcntg INTEGER

GenEquipSecurityRadiusServerConfigurationEntry  
SEQUENCE    
  genEquipSecurityAccessControlRadiusServerId INTEGER
  genEquipSecurityAccessControlRadiusServerIpV4Address IpAddress
  genEquipSecurityAccessControlRadiusServerIpv6Address OCTET STRING
  genEquipSecurityAccessControlRadiusServerPort INTEGER
  genEquipSecurityAccessControlRadiusServerRetries INTEGER
  genEquipSecurityAccessControlRadiusServerTimeout INTEGER
  genEquipSecurityAccessControlRadiusServerSharedSecret OCTET STRING
  genEquipSecurityAccessControlRadiusServerConnectivityStatus EnableDisable

GenEquipSecurityAccessControlRadiusUsersEntry  
SEQUENCE    
  genEquipSecurityAccessControlRadiusUsersId DisplayString
  genEquipSecurityAccessControlRadiusUserInstances INTEGER
  genEquipSecurityAccessControlRadiusUsersAccessChannels INTEGER
  genEquipSecurityAccessControlRadiusUsersEthReadLevel RaduisAcceaaLevel
  genEquipSecurityAccessControlRadiusUsersEthWriteLevel RaduisAcceaaLevel
  genEquipSecurityAccessControlRadiusUsersMngReadLevel RaduisAcceaaLevel
  genEquipSecurityAccessControlRadiusUsersMngWriteLevel RaduisAcceaaLevel
  genEquipSecurityAccessControlRadiusUsersRadioReadLevel RaduisAcceaaLevel
  genEquipSecurityAccessControlRadiusUsersRadioWriteLevel RaduisAcceaaLevel
  genEquipSecurityAccessControlRadiusUsersSecurityReadLevel RaduisAcceaaLevel
  genEquipSecurityAccessControlRadiusUsersSecurityWriteLevel RaduisAcceaaLevel
  genEquipSecurityAccessControlRadiusUsersSyncReadLevel RaduisAcceaaLevel
  genEquipSecurityAccessControlRadiusUsersSyncWriteLevel RaduisAcceaaLevel
  genEquipSecurityAccessControlRadiusUsersTdmReadLevel RaduisAcceaaLevel
  genEquipSecurityAccessControlRadiusUsersTdmWriteLevel RaduisAcceaaLevel

GenEquipSecurityCsrAttributesEntry  
SEQUENCE    
  genEquipSecurityCsrAttributesIndex INTEGER
  genEquipSecurityCsrAttributesCountry DisplayString
  genEquipSecurityCsrAttributesLocality DisplayString
  genEquipSecurityCsrAttributesState DisplayString
  genEquipSecurityCsrAttributesOrganization DisplayString
  genEquipSecurityCsrAttributesOu DisplayString
  genEquipSecurityCsrAttributesCommonName DisplayString
  genEquipSecurityCsrAttributesEmail DisplayString
  genEquipSecurityCsrAttributesFileFormat CsrFileFormat

GenEquipSecurityCsrUploadConfigEntry  
SEQUENCE    
  genEquipSecurityCsrUploadConfigIndex INTEGER
  genEquipSecurityCsrUploadConfigIpv4Address IpAddress
  genEquipSecurityCsrUploadConfigIpV6Address OCTET STRING
  genEquipSecurityCsrUploadConfigTableUsername DisplayString
  genEquipSecurityCsrUploadConfigPassword DisplayString
  genEquipSecurityCsrUploadConfigPath DisplayString
  genEquipSecurityCsrUploadConfigFilename DisplayString

GenEquipSecurityCertificateDownloadConfigEntry  
SEQUENCE    
  genEquipSecurityCertificateDownloadConfigIndex INTEGER
  genEquipSecurityCertificateDownloadConfigIpv4Address IpAddress
  genEquipSecurityCertificateDownloadConfigIpV6Address OCTET STRING
  genEquipSecurityCertificateDownloadConfigUsername DisplayString
  genEquipSecurityCertificateDownloadConfigPassword DisplayString
  genEquipSecurityCertificateDownloadConfigPath DisplayString
  genEquipSecurityCertificateDownloadConfigFilename DisplayString

Defined Values

microwave-radio 1.3.6.1.4.1.2281
OBJECT IDENTIFIER    

genEquip 1.3.6.1.4.1.2281.10
OBJECT IDENTIFIER    

genEquipUnit 1.3.6.1.4.1.2281.10.1
OBJECT IDENTIFIER    

genEquipUnitInfo 1.3.6.1.4.1.2281.10.1.1
OBJECT IDENTIFIER    

genEquipLastCfgTimeStamp 1.3.6.1.4.1.2281.10.1.1.1
This parameter represents the configuration change counter. On every conf. change this counter is increased by 1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipRealTimeandDate 1.3.6.1.4.1.2281.10.1.1.2
This parameter specifies the real time and date Format 'YYYY-MM-DD,HH:MM:SS' (Hexadecimal). A date-time specification: field octets contents range ----- ------ -------- ----- 1 1-2 year 0..65536 2 3 month 1..12 3 4 day 1..31 4 5 hour 0..23 5 6 minutes 0..59 6 7 seconds 0..60 (use 60 for leap-second) 7 8 deci-seconds 0..9 For example, Tuesday May 26, 1992 at 1:30:15 PM EDT would be displayed as: 07 c8 05 1a 0d 1e 0f 00 (1992 -5 -26, 13:30:15 )
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(8)  

genEquipPMGenTime 1.3.6.1.4.1.2281.10.1.1.3
This value indicates the generation time of the Performance Monitor file. The value is presented in time_t format.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipInvGenTime 1.3.6.1.4.1.2281.10.1.1.4
This value indicates the generation time of the Inventory information file. The inventory file holds the configuration information of the unit. The value is presented in time_t format.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipOperation 1.3.6.1.4.1.2281.10.1.1.5
Enables to perform HW reset to the indoor unit.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noAction(0), idcHwReset(1)  

genEquipMIBVersion 1.3.6.1.4.1.2281.10.1.1.6
This value indicates MIB version.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipUnitCLLI 1.3.6.1.4.1.2281.10.1.1.7
This value represents a general purpose CLLI-like text field. The CLLI field is attached to traps generated from this NE.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..255)  

genEquipUnitMeasurementSystem 1.3.6.1.4.1.2281.10.1.1.8
This value represents the measurement system used by the system. (metric or imperal).
Status: mandatory Access: read-write
OBJECT-TYPE    
  MetricImperial  

genEquipUnitIduTemperature 1.3.6.1.4.1.2281.10.1.1.9
This value indicates the IDU temperature, according to the measurement system chosen. (genEquipUnitMeasurementSystem)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipUnitIduVoltageInput 1.3.6.1.4.1.2281.10.1.1.10
Voltages Input.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipUnitInfoTime 1.3.6.1.4.1.2281.10.1.1.11
OBJECT IDENTIFIER    

genEquipUnitGMTHours 1.3.6.1.4.1.2281.10.1.1.11.1
This parameter represent the offset in hours from GMT.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER -12..13  

genEquipUnitGMTMins 1.3.6.1.4.1.2281.10.1.1.11.2
This parameter represents the offset in minutes from GMT.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..59  

genEquipUnitDaylightSavingTimeStartMonth 1.3.6.1.4.1.2281.10.1.1.11.7
This parameter represents the start Month of the daylight saving time.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..12  

genEquipUnitDaylightSavingTimeStartDay 1.3.6.1.4.1.2281.10.1.1.11.8
This parameter represents the start Day of the daylight saving time.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..31  

genEquipUnitDaylightSavingTimeEndMonth 1.3.6.1.4.1.2281.10.1.1.11.9
This parameter represents the end month of the daylight saving time.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..12  

genEquipUnitDaylightSavingTimeEndDay 1.3.6.1.4.1.2281.10.1.1.11.10
This parameter represents the end day of the daylight saving time.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..31  

genEquipUnitDaylightSavingTimeOffset 1.3.6.1.4.1.2281.10.1.1.11.11
Daylight saving offset hours. for a value different then '0', at the starting date of the daylight saving time the time will jump forward in this value. at the end date of the daylight saving time, the time will jump backwards in this value.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..23  

genEquipUnitInfoTimeServicesTable 1.3.6.1.4.1.2281.10.1.1.11.12
This table contains the time services properties.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipUnitInfoTimeServicesEntry

genEquipUnitInfoTimeServicesEntry 1.3.6.1.4.1.2281.10.1.1.11.12.1
This table entry contains the time services properties.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipUnitInfoTimeServicesEntry  

genEquipUnitInfoTimeServicesIndex 1.3.6.1.4.1.2281.10.1.1.11.12.1.1
The index of the table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipUnitInfoTimeServicesUtcHours 1.3.6.1.4.1.2281.10.1.1.11.12.1.2
The required hours offset relative to the UTC (Universal Time Coordinated).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER -12..13  

genEquipUnitInfoTimeServicesUtcMinutes 1.3.6.1.4.1.2281.10.1.1.11.12.1.3
The required minutes offset relative to the UTC (Universal Time Coordinated).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..59  

genEquipUnitInfoTimeServicesDstStartMonth 1.3.6.1.4.1.2281.10.1.1.11.12.1.4
The month when the DST (Daylight Saving Time) is required to start.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..12  

genEquipUnitInfoTimeServicesDstStartDay 1.3.6.1.4.1.2281.10.1.1.11.12.1.5
The day when the DST (Daylight Saving Time) is required to start.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..31  

genEquipUnitInfoTimeServicesDstEndMonth 1.3.6.1.4.1.2281.10.1.1.11.12.1.6
The month when the DST (Daylight Saving Time) is required to end.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..12  

genEquipUnitInfoTimeServicesDstEndDay 1.3.6.1.4.1.2281.10.1.1.11.12.1.7
The day when the DST (Daylight Saving Time) is required to end.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..31  

genEquipUnitInfoTimeServicesDstOffset 1.3.6.1.4.1.2281.10.1.1.11.12.1.8
The required offset for DST (Daylight Saving Time) in hours.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..23  

genEquipUnitInfoTimeServicesUtcDateAndTime 1.3.6.1.4.1.2281.10.1.1.11.12.1.9
UTC (Universal Time Coordinated) date and time.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

genEquipUnitInfoTimeServicesUtcCurrentDateAndTime 1.3.6.1.4.1.2281.10.1.1.11.12.1.10
The calculated current local date & time based on the local clock, UTC and DST (Daylight Saving Time) configurations.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipUnitIduPowerSupply1AlarmAdmin 1.3.6.1.4.1.2281.10.1.1.12
This parameter is relevant only for IDU with more than one power supply units. The user can choose to disable (ignore the alarm) of one of the power supply units.
Status: mandatory Access: read-write
OBJECT-TYPE    
  EnableDisable  

genEquipUnitIduPowerSupply2AlarmAdmin 1.3.6.1.4.1.2281.10.1.1.13
This parameter is relevant only for IDU with more than two power supply units. The user can choose to disable (ignore the alarm) of one of the power supply units.
Status: mandatory Access: read-write
OBJECT-TYPE    
  EnableDisable  

genEquipUnitInfoNG 1.3.6.1.4.1.2281.10.1.1.14
OBJECT IDENTIFIER    

genEquipUnitName 1.3.6.1.4.1.2281.10.1.1.14.1
The name of the system.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipUnitDescription 1.3.6.1.4.1.2281.10.1.1.14.2
A ahort description of the system.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipUnitContactPerson 1.3.6.1.4.1.2281.10.1.1.14.3
Contact person.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipUnitLocation 1.3.6.1.4.1.2281.10.1.1.14.4
The location of the system.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipUnitLatitude 1.3.6.1.4.1.2281.10.1.1.14.5
The latitude of the system.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipUnitLongitude 1.3.6.1.4.1.2281.10.1.1.14.6
The longitude of system.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipUnitIpAddressType 1.3.6.1.4.1.2281.10.1.1.14.7
IP address Family.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ipv4(0), ipv6(1)  

genEquipUnitInfoNGTdmInterfaceStandard 1.3.6.1.4.1.2281.10.1.1.14.8
The TDM interface standard: ETSI (Erupean) or ANSI (North American)
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ets1(0), ansi(1)  

genEquipUnitInfoNTP 1.3.6.1.4.1.2281.10.1.1.11.6
OBJECT IDENTIFIER    

genEquipUnitInfoNTPAdmin 1.3.6.1.4.1.2281.10.1.1.11.6.1
This parameter represents the NTP Admin state
Status: mandatory Access: read-write
OBJECT-TYPE    
  EnableDisable  

genEquipUnitInfoNTPServerIP 1.3.6.1.4.1.2281.10.1.1.11.6.2
This parameter represents the IP address of the NTP Server
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

genEquipUnitInfoNTPStatus 1.3.6.1.4.1.2281.10.1.1.11.6.3
This parameter represents the NTP Service status
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER down(0), up(1)  

genEquipUnitInfoNTPSync 1.3.6.1.4.1.2281.10.1.1.11.6.4
This parameter returns the IP address of the NTP server, with which the system is currently synchronized. Returned strings: (i) - the IP address of the reference NTP server, according to IPv4/v6 format. (ii) - 'LOCAL' if synchronized on local clock. (iii) - 'N/A' if not synchronized. Valid only when admin is 'disabled'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipUnitInfoNTPPollInterval 1.3.6.1.4.1.2281.10.1.1.11.6.5
This parameter represents the NTP polling interval in minutes
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 64..1024  

genEquipUnitInfoNtpStatusTable 1.3.6.1.4.1.2281.10.1.1.11.6.6
This table shows the status of the NTP (Network Time Protocol).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipUnitInfoNtpStatusEntry

genEquipUnitInfoNtpStatusEntry 1.3.6.1.4.1.2281.10.1.1.11.6.6.1
Entry containing the data of the NTP status.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipUnitInfoNtpStatusEntry  

genEquipUnitInfoNtpStatusIndex 1.3.6.1.4.1.2281.10.1.1.11.6.6.1.1
Index of the table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipUnitInfoNtpStatusPollInterval 1.3.6.1.4.1.2281.10.1.1.11.6.6.1.2
Indicates the time interval in minutes in which the NTP client polls the server it is locked to.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..1024  

genEquipUnitInfoNtpStatusSyncServerIP 1.3.6.1.4.1.2281.10.1.1.11.6.6.1.3
he IPv4 address of the NTP server that the client is currently locked on.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

genEquipUnitInfoNtpStatusLockState 1.3.6.1.4.1.2281.10.1.1.11.6.6.1.4
Indicates the NTP client lock status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER none(0), local(1), locked(2)  

genEquipUnitInfoNtpConfigTable 1.3.6.1.4.1.2281.10.1.1.11.6.7
This table allows the configuration of the NTP (Network Time Protocol).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipUnitInfoNtpConfigEntry

genEquipUnitInfoNtpConfigEntry 1.3.6.1.4.1.2281.10.1.1.11.6.7.1
Entry containing the data of the NTP configuration.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipUnitInfoNtpConfigEntry  

genEquipUnitInfoNtpConfigIndex 1.3.6.1.4.1.2281.10.1.1.11.6.7.1.1
Index of the table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipUnitInfoNtpConfigAdmin 1.3.6.1.4.1.2281.10.1.1.11.6.7.1.2
The administrative state of the NTP (Network Time Protocol) feature.
Status: mandatory Access: read-write
OBJECT-TYPE    
  EnableDisable  

genEquipUnitInfoNtpConfigVersion 1.3.6.1.4.1.2281.10.1.1.11.6.7.1.3
The NTP (Network Time Protocol) version that is being used.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ntpv3(1), ntpv4(2)  

genEquipUnitInfoNtpConfigServerIPaddress1 1.3.6.1.4.1.2281.10.1.1.11.6.7.1.4
NTP server IPv4 address that is required in first priority.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

genEquipUnitInfoNtpConfigServerIPaddress2 1.3.6.1.4.1.2281.10.1.1.11.6.7.1.5
NTP server IPv4 address that is required in second priority.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

genEquipUnitInventory 1.3.6.1.4.1.2281.10.1.2
OBJECT IDENTIFIER    

genEquipUnitIDUSerialNumber 1.3.6.1.4.1.2281.10.1.2.1
IDU Serial number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipUnitIDUPartNumber 1.3.6.1.4.1.2281.10.1.2.2
IDU Part number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipUnitInventoryNG 1.3.6.1.4.1.2281.10.1.2.10
OBJECT IDENTIFIER    

genEquipInventoryTable 1.3.6.1.4.1.2281.10.1.2.10.1
inventory common table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipInventoryEntry

genEquipInventoryEntry 1.3.6.1.4.1.2281.10.1.2.10.1.1
inventory common table Entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipInventoryEntry  

genEquipInventorySlotIndex 1.3.6.1.4.1.2281.10.1.2.10.1.1.1
slot index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipInventoryCardName 1.3.6.1.4.1.2281.10.1.2.10.1.1.2
Card name.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipInventoryCardType 1.3.6.1.4.1.2281.10.1.2.10.1.1.3
Card type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  InventoryCardType  

genEquipInventoryCardSubType 1.3.6.1.4.1.2281.10.1.2.10.1.1.4
Card sub type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipInventoryPartNumber 1.3.6.1.4.1.2281.10.1.2.10.1.1.5
Part number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipInventorySerialNumber 1.3.6.1.4.1.2281.10.1.2.10.1.1.6
Serial number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipInventoryNumberWorkingDays 1.3.6.1.4.1.2281.10.1.2.10.1.1.7
Number of working days.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipUnitLicenseInfo 1.3.6.1.4.1.2281.10.1.3
OBJECT IDENTIFIER    

genEquipUnitLicenseType 1.3.6.1.4.1.2281.10.1.3.1
The unit license type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER default(0), normal(1), demo(2)  

genEquipUnitLicenseCode 1.3.6.1.4.1.2281.10.1.3.2
The user license code that determines the NE license rights.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipUnitACMLicense 1.3.6.1.4.1.2281.10.1.3.3
The ACM rights for the NE on the current license
Status: mandatory Access: read-only
OBJECT-TYPE    
  AllowedNotAllowed  

genEquipUnitSwitchAppLicense 1.3.6.1.4.1.2281.10.1.3.4
The switch application rights for the NE on the current license. Switch is either managed-switch or metro switch.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER single-pipe(0), switch(8)  

genEquipUnitCapacityLicense 1.3.6.1.4.1.2281.10.1.3.5
The radio capacity allowed for the NE on the current license
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 10..510  

genEquipUnitLicenseDemoAdmin 1.3.6.1.4.1.2281.10.1.3.6
The Admin state of the demo mode.
Status: mandatory Access: read-write
OBJECT-TYPE    
  EnableDisable  

genEquipUnitLicenseDemoTimer 1.3.6.1.4.1.2281.10.1.3.7
The Demo timer in hours
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipUnitLicenseSyncU 1.3.6.1.4.1.2281.10.1.3.8
This parameter indicates whether the synchronization unit license is allowed. This license allows configuring synchronization sources for clock distribution.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AllowedNotAllowed  

genEquipUnitLicenseNetworkResiliency 1.3.6.1.4.1.2281.10.1.3.9
This parameter indicates whether the network resiliency license is allowed. This license allows configuring xSTP protocols and TDM path protection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AllowedNotAllowed  

genEquipUnitLicenseTDMCapacity 1.3.6.1.4.1.2281.10.1.3.10
This parameter indicates the number of TDM trails per radio allowed by the current license, if allowed. When TDM capacity license is allowed all scripts are allowed in the radio.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AllowedNotAllowed  

genEquipUnitLicenseTDMCapacityValue 1.3.6.1.4.1.2281.10.1.3.11
This parameter indicates the number of TDM trails per radio allowed by the current license, if relevant. The TDM capacity value is not relevant if the genEquipUnitLicenseTDMCapacity is not allowed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipUnitLicensePerUsage 1.3.6.1.4.1.2281.10.1.3.12
This parameter indicates whether the per-usage license is allowed. This license allows configuring all features and causes their use to be reported to NMS. If the usage license is allowed, all other licenses are not relevant, as all the licenses are open for configuration.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AllowedNotAllowed  

genEquipUnitLicenseAsymScripts 1.3.6.1.4.1.2281.10.1.3.13
This parameter indicates whether the asymmetrical scripts license is allowed. This license allows loading asymmetrical scripts.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AllowedNotAllowed  

genEquipUnitLicenseDateCode 1.3.6.1.4.1.2281.10.1.3.14
This parameter indicates the generation date and time of the current installed license. Format is 'YYYY-MM-DD,HH:MM:SS' (Hexadecimal).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipUnitLicenseValidationNumber 1.3.6.1.4.1.2281.10.1.3.15
This parameter indicates the validation number of the current installed license. It can be used as a proof (for LMS) that the license key was installed in order to get a downgrade refund.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipUnitLicenseFeatureTable 1.3.6.1.4.1.2281.10.1.3.16
This table shows for each feature what is its valid license and whether the license has been violated or not.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipUnitLicenseFeatureEntry

genEquipUnitLicenseFeatureEntry 1.3.6.1.4.1.2281.10.1.3.16.1
This table entry shows for each feature what is its valid license and whether the license has been violated or not.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipUnitLicenseFeatureEntry  

genEquipUnitLicenseFeatureId 1.3.6.1.4.1.2281.10.1.3.16.1.1
A unique number which indicates the Id of the feature
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipUnitLicenseFeatureName 1.3.6.1.4.1.2281.10.1.3.16.1.2
The name of the feature.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipUnitLicenseFeatureDescription 1.3.6.1.4.1.2281.10.1.3.16.1.3
A short description of the feature.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipUnitLicenseFeatureIsUsed 1.3.6.1.4.1.2281.10.1.3.16.1.4
Indicates whether the licensed feature is actually in used or its quantity that currently is in use.
Status: mandatory Access: read-only
OBJECT-TYPE    
  LicenseGeneric  

genEquipUnitLicenseFeatureIsAllowed 1.3.6.1.4.1.2281.10.1.3.16.1.5
Indicates whether a licensed feature is allowed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  LicenseGeneric  

genEquipUnitLicenseViolationStatus 1.3.6.1.4.1.2281.10.1.3.16.1.6
Indicates whether the actual configuration violates the feature license.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ok(0), violated(1)  

genEquipUnitLicenseCutThrough 1.3.6.1.4.1.2281.10.1.3.20
This parameter indicates whether the cut-through license is allowed. This license allows using the cut-through frames in the TM.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AllowedNotAllowed  

genEquipUnitLicenseTdmInterfaceStandard 1.3.6.1.4.1.2281.10.1.3.21
The TDM interface standard: ETSI (European) or ANSI (North American).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ets1(0), ansi(1)  

genEquipUnitExternalAlarms 1.3.6.1.4.1.2281.10.1.4
OBJECT IDENTIFIER    

genEquipUnitAlarmInput 1.3.6.1.4.1.2281.10.1.4.1
OBJECT IDENTIFIER    

genEquipUnitAlarmInputTable 1.3.6.1.4.1.2281.10.1.4.1.1
External input alarm table. Using the table to manage the admin state of the external input alarm (Enable or Disable it). Set a description and severity.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipUnitAlarmInputEntry

genEquipUnitAlarmInputEntry 1.3.6.1.4.1.2281.10.1.4.1.1.1
External input alarm table. Using the table to manage the admin state of the external input alarm (Enable or Disable it). Set a description and severity.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipUnitAlarmInputEntry  

genEquipUnitAlarmInputCounter 1.3.6.1.4.1.2281.10.1.4.1.1.1.1
External input alarm table index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipUnitAlarmInputAdmin 1.3.6.1.4.1.2281.10.1.4.1.1.1.2
The Admin state of the External input alarm table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  EnableDisableSMI2  

genEquipUnitAlarmInputText 1.3.6.1.4.1.2281.10.1.4.1.1.1.3
External input alarm description.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..99)  

genEquipUnitAlarmInputSeverity 1.3.6.1.4.1.2281.10.1.4.1.1.1.4
External input alarm severity.
Status: mandatory Access: read-write
OBJECT-TYPE    
  InputSeverity  

genEquipUnitAlarmInputState 1.3.6.1.4.1.2281.10.1.4.1.1.1.5
The state, raised or cleared, of the external alarm input.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OffOn  

genEquipUnitAlarmOutput 1.3.6.1.4.1.2281.10.1.4.2
OBJECT IDENTIFIER    

genEquipUnitAlarmOutputTable 1.3.6.1.4.1.2281.10.1.4.2.1
External output alarm table. using the table to manage the admin state of the external input alarm , read the status and set an output group.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipUnitAlarmOutputEntry

genEquipUnitAlarmOutputEntry 1.3.6.1.4.1.2281.10.1.4.2.1.1
External output alarm table. using the table to manage the admin state of the external input alarm , read the status and set an output group.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipUnitAlarmOutputEntry  

genEquipUnitAlarmOutputCounter 1.3.6.1.4.1.2281.10.1.4.2.1.1.1
External output alarm table index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipUnitAlarmOutputAdmin 1.3.6.1.4.1.2281.10.1.4.2.1.1.2
The Admin state of the External output alarm. When 'Enabled', the functionality will be: (i) If no alarms are raised, the N.O. (normally open) contact will be opened, while the N.C. (normally closed) contact will be connected to the COM contact. (ii) When an alarm is raised, or the system power is OFF, the N.O will be connected to the COM contact, while the N.C. contact will remain opened. When 'Test' option is selected, the dry contacts behave as an alarm is raised in the system, as described in case (ii) above.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1), test(2)  

genEquipUnitAlarmOutputStatus 1.3.6.1.4.1.2281.10.1.4.2.1.1.3
The current stauts of the External output alarm table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(0), on(1), on-test(2)  

genEquipUnitAlarmOutputGroup 1.3.6.1.4.1.2281.10.1.4.2.1.1.4
The description of the group to which the external output alarm belongs.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER communication(1), quality-of-service(2), processing(3), equipment(4), environmental(5), all-groups(6)  

genEquipUnitShelf 1.3.6.1.4.1.2281.10.1.5
OBJECT IDENTIFIER    

genEquipUnitShelfInstallation 1.3.6.1.4.1.2281.10.1.5.1
This value indicates the NE installation type (standalone or module/card within a chassis).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER standalone(0), chassisModule(1)  

genEquipUnitShelfModuleRole 1.3.6.1.4.1.2281.10.1.5.2
This value indicates the NE module role (main unit or extention).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER main(0), extention(1)  

genEquipUnitShelfSlotLabel 1.3.6.1.4.1.2281.10.1.5.3
Slot label is a user defined description for the module in the slot.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..255)  

genEquipUnitShelfArchivesOperationStatus 1.3.6.1.4.1.2281.10.1.5.4
Shelf-wide configuration archives [backup/restore] operation status. Used also when creating archive for unit info. Relevant only for main units. - ready(0) - inProgress(1), - success(2), - failure(3)
Status: mandatory Access: read-only
OBJECT-TYPE    
  ProgressStatus  

genEquipUnitShelfManagmentTable 1.3.6.1.4.1.2281.10.1.5.5
This table contains information about the IDUs that may be in the shelf (population, communication status, most severe alarm) and provides the ability to backup/restore SW for each IDU. Relevant only for main units.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipUnitShelfManagmentEntry

genEquipUnitShelfManagmentEntry 1.3.6.1.4.1.2281.10.1.5.5.1
This table keeps the shelf information on all the modules in the shelf (population, status, most severe alarm) and provides the ability for backup/restore command or SW download. Relevant only for main units.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipUnitShelfManagmentEntry  

genEquipUnitShelfManagmentSlot 1.3.6.1.4.1.2281.10.1.5.5.1.1
This value is the slot number used as an index for this table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SlotId  

genEquipUnitShelfManagmentSlotPopulation 1.3.6.1.4.1.2281.10.1.5.5.1.2
Slot population state, which indicates if the slot is occupied or not. Relevant only for main units.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER not-present(0), present(1)  

genEquipUnitShelfManagmentCommunicationStatus 1.3.6.1.4.1.2281.10.1.5.5.1.3
This value indicates if the slot can be reached or not. Relevant only for main units.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER communicationDown(0), communicationUp(1)  

genEquipUnitShelfManagmentSlotMostSevereAlarm 1.3.6.1.4.1.2281.10.1.5.5.1.4
This value is the most severe alarm for the module on this slot. Relevant only for main unit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Severity  

genEquipUnitShelfManagmentMngSwCommand 1.3.6.1.4.1.2281.10.1.5.5.1.5
The command to be executed to manage SW versions. Relevant only for main units. Possible values are: - noOperation(0) - downloadUpgradeVersion(1) - upgrade(2) - rollback(3) - downgrade(4) - downloadDowngradeVersion(5)
Status: mandatory Access: read-write
OBJECT-TYPE    
  SwCommand  

genEquipUnitShelfManagmentSlotReset 1.3.6.1.4.1.2281.10.1.5.5.1.6
This parameter Allows resetting specific unit according to genEquipUnitShelfManagmentSlot table index.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OffOn  

genEquipUnitShelfManagmentSlotIp 1.3.6.1.4.1.2281.10.1.5.5.1.7
Slot SNMP Management IP address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

genEquipUnitShelfReset 1.3.6.1.4.1.2281.10.1.5.6
This parameter allows resetting of entire shelf.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OffOn  

genEquipUnitshelfAllODUAdmin 1.3.6.1.4.1.2281.10.1.5.7
The unit is configured as all outdoor unit, enable or disable it.
Status: mandatory Access: read-write
OBJECT-TYPE    
  EnableDisable  

genEquipUnitShelfSlotConfigTable 1.3.6.1.4.1.2281.10.1.5.8
Slot configuration table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipUnitShelfSlotConfigEntry

genEquipUnitShelfSlotConfigEntry 1.3.6.1.4.1.2281.10.1.5.8.1
This table allows configuration of card population parameters.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipUnitShelfSlotConfigEntry  

genEquipUnitShelfSlotConfigSlotID 1.3.6.1.4.1.2281.10.1.5.8.1.1
This value is the slot number used as an index for this table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SlotId  

genEquipUnitShelfSlotConfigExpectedCardType 1.3.6.1.4.1.2281.10.1.5.8.1.2
Expected card type in current slot.
Status: mandatory Access: read-write
OBJECT-TYPE    
  InventoryCardType  

genEquipUnitShelfSlotConfigLabel 1.3.6.1.4.1.2281.10.1.5.8.1.3
Slot label.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipUnitShelfSlotConfigAdmin 1.3.6.1.4.1.2281.10.1.5.8.1.4
Slot admin state.
Status: mandatory Access: read-write
OBJECT-TYPE    
  EnableDisable  

genEquipUnitShelfSlotConfigSlotReset 1.3.6.1.4.1.2281.10.1.5.8.1.5
This parameter Allows resetting specific unit according to genEquipUnitShelfManagmentSlot table index.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OffOn  

genEquipUnitShelfTccConfigTable 1.3.6.1.4.1.2281.10.1.5.9
TCC configuration table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipUnitShelfTccConfigEntry

genEquipUnitShelfTccConfigEntry 1.3.6.1.4.1.2281.10.1.5.9.1
This table allows configuration of TCC population parameters.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipUnitShelfTccConfigEntry  

genEquipUnitShelfTccConfigSlotID 1.3.6.1.4.1.2281.10.1.5.9.1.1
This value is the TCC slot number used as an index for this table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SlotId  

genEquipUnitShelfTccConfigExpectedCardType 1.3.6.1.4.1.2281.10.1.5.9.1.2
Expected card type in current TCC slot.
Status: mandatory Access: read-write
OBJECT-TYPE    
  InventoryCardType  

genEquipUnitShelfTccConfigLabel 1.3.6.1.4.1.2281.10.1.5.9.1.3
TCC label.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipUnitShelfTccConfigAdmin 1.3.6.1.4.1.2281.10.1.5.9.1.4
TCC admin state.
Status: mandatory Access: read-write
OBJECT-TYPE    
  EnableDisable  

genEquipUnitShelfTccConfigReset 1.3.6.1.4.1.2281.10.1.5.9.1.5
This parameter Allows resetting specific unit according to genEquipUnitShelfManagmentSlot table index.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OffOn  

genEquipUnitShelfSlotStatusTable 1.3.6.1.4.1.2281.10.1.5.10
This table contains information about the status of the cards currently inserted in the system.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipUnitShelfSlotStatusEntry

genEquipUnitShelfSlotStatusEntry 1.3.6.1.4.1.2281.10.1.5.10.1
This table entry contains information about the status of the cards currently inserted in the system.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipUnitShelfSlotStatusEntry  

genEquipUnitShelfSlotStatusSlotID 1.3.6.1.4.1.2281.10.1.5.10.1.1
Slot where PW-LIC is inserted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SlotId  

genEquipUnitShelfSlotStatusOccupancy 1.3.6.1.4.1.2281.10.1.5.10.1.2
Slot Occupancy.
Status: mandatory Access: read-only
OBJECT-TYPE    
  CardOccupancy  

genEquipUnitShelfSlotStatusAllowedCardTypes 1.3.6.1.4.1.2281.10.1.5.10.1.3
shelf slot allowed card types.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter64  

genEquipUnitShelfSlotStatusCardType 1.3.6.1.4.1.2281.10.1.5.10.1.4
Shelf Slot card type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  InventoryCardType  

genEquipUnitShelfSlotStatusOperationalState 1.3.6.1.4.1.2281.10.1.5.10.1.5
Operational State.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OperState  

genEquipUnitShelfSlotStatusCommunication 1.3.6.1.4.1.2281.10.1.5.10.1.6
Slot Operational State.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DownUp  

genEquipUnitShelfTccStatusTable 1.3.6.1.4.1.2281.10.1.5.11
This table contains information about the status of the TCC currently inserted in the system.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipUnitShelfTccStatusEntry

genEquipUnitShelfTccStatusEntry 1.3.6.1.4.1.2281.10.1.5.11.1
This table entry contains information about the status of the TCC currently inserted in the system.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipUnitShelfTccStatusEntry  

genEquipUnitShelfTccStatusSlotID 1.3.6.1.4.1.2281.10.1.5.11.1.1
Slot where PW-LIC is inserted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SlotId  

genEquipUnitShelfTccStatusOccupancy 1.3.6.1.4.1.2281.10.1.5.11.1.2
Slot Occupancy.
Status: mandatory Access: read-only
OBJECT-TYPE    
  CardOccupancy  

genEquipUnitShelfTccStatusAllowedCardTypes 1.3.6.1.4.1.2281.10.1.5.11.1.3
shelf slot allowed card types.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter64  

genEquipUnitShelfTccStatusCardType 1.3.6.1.4.1.2281.10.1.5.11.1.4
Shelf Slot card type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  InventoryCardType  

genEquipUnitShelfTccStatusOperationalState 1.3.6.1.4.1.2281.10.1.5.11.1.5
Operational State.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OperState  

genEquipUnitShelfTccStatusCommunication 1.3.6.1.4.1.2281.10.1.5.11.1.6
Slot Operational State.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DownUp  

genEquipUnitShelfManagmentSeverityTable 1.3.6.1.4.1.2281.10.1.5.12
This table indicates the number of current raised alarms per slot.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipUnitShelfManagmentSeverityEntry

genEquipUnitShelfManagmentSeverityEntry 1.3.6.1.4.1.2281.10.1.5.12.1
This table entry indicates the number of current raised alarms per slot.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipUnitShelfManagmentSeverityEntry  

genEquipUnitShelfManagmentSeveritySlot 1.3.6.1.4.1.2281.10.1.5.12.1.1
The slot ID number that identifies it.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipUnitShelfManagmentSeverityCritical 1.3.6.1.4.1.2281.10.1.5.12.1.2
The number of alarms with 'Critical' severity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipUnitShelfManagmentSeverityMajor 1.3.6.1.4.1.2281.10.1.5.12.1.3
The number of alarms with 'Major' severity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipUnitShelfManagmentSeverityMinor 1.3.6.1.4.1.2281.10.1.5.12.1.4
The number of alarms with 'Minor' severity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipUnitShelfManagmentSeverityWarning 1.3.6.1.4.1.2281.10.1.5.12.1.5
The number of alarms with 'Warning' severity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipUnitShelfManagmentSeverityIndeterminate 1.3.6.1.4.1.2281.10.1.5.12.1.6
The number of alarms with 'Indeterminate' severity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipUnitShelfPdcFanStatusTable 1.3.6.1.4.1.2281.10.1.5.13
This table shows for fun card.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipUnitShelfPdcFanStatusEntry

genEquipUnitShelfPdcFanStatusEntry 1.3.6.1.4.1.2281.10.1.5.13.1
This table shows for fun card.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipUnitShelfPdcFanStatusEntry  

genEquipUnitShelfPdcFanStatusPdcFanId 1.3.6.1.4.1.2281.10.1.5.13.1.1
pdc-fan-id
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipUnitShelfPdcFanStatusPdcFanExMonitor 1.3.6.1.4.1.2281.10.1.5.13.1.2
pdc-fan-existent monitor.
Status: mandatory Access: read-write
OBJECT-TYPE    
  EnableDisable  

genEquipUnitShelfPdcFanStatusPdcFanOccupancy 1.3.6.1.4.1.2281.10.1.5.13.1.3
card_occupancy.
Status: mandatory Access: read-only
OBJECT-TYPE    
  CardOccupancy  

genEquipUnitShelfPdcFanStatusPdcFanCardType 1.3.6.1.4.1.2281.10.1.5.13.1.4
Indicates whether the licensed feature is actually in used or its quantity that currently is in use.
Status: mandatory Access: read-only
OBJECT-TYPE    
  InventoryCardType  

genEquipUnitShelfAbcMuxTable 1.3.6.1.4.1.2281.10.1.5.14
This table allows enabling/disabling each ABC MUX group. ABC groups can be defined on top of these MUX.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipUnitShelfAbcMuxEntry

genEquipUnitShelfAbcMuxEntry 1.3.6.1.4.1.2281.10.1.5.14.1
This table entry allows enabling/disabling each ABC MUX group. ABC groups can be defined on top of these MUX.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipUnitShelfAbcMuxEntry  

genEquipUnitShelfAbcMuxNumber 1.3.6.1.4.1.2281.10.1.5.14.1.1
Identifier for each of the possible MUXs which choose between using the ABC trunks or the port for multi-directional radios
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipUnitShelfAbcMuxAdmin 1.3.6.1.4.1.2281.10.1.5.14.1.2
Enables the MUX (for ABC) or disables it (for multi-directional radios).
Status: mandatory Access: read-write
OBJECT-TYPE    
  EnableDisable  

genEquipUnitShelfMultiplexTrafficSource 1.3.6.1.4.1.2281.10.1.5.23
The parameter multiplex traffic between slot 1 and slot 12.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..12  

genEquipUnitShelfMaskUnderVoltageAlarmFirstPowerFeed 1.3.6.1.4.1.2281.10.1.5.24
Mask undervoltage alarm on 1st DC power feed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  EnableDisable  

genEquipUnitShelfMaskUnderVoltageAlarmSecondPowerFeed 1.3.6.1.4.1.2281.10.1.5.25
Mask undervoltage alarm on 2nd DC power feed
Status: mandatory Access: read-write
OBJECT-TYPE    
  EnableDisable  

genEquipProtection 1.3.6.1.4.1.2281.10.1.6
OBJECT IDENTIFIER    

genEquipProtectionAdmin 1.3.6.1.4.1.2281.10.1.6.1
The Admin mode of the protection. In case of protection2Plus2Hsb this parameter should be configured in the main and extension slots.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER protection1Plus1Hsb(2), protectionDisable(3), protection2Plus2Hsb(4), protection2Plus0Hsb(5)  

genEquipProtectionMode 1.3.6.1.4.1.2281.10.1.6.2
In protection mode, the card can be either active or standby
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER active(0), standby(1)  

genEquipProtectionMateIPAddr 1.3.6.1.4.1.2281.10.1.6.3
Same parameter as genEquipNetworkMateIp. In case of 1+1 protection it is the protected card (Mate) IP address. In case of 2+2 protection it is the IP address of the protected unit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

genEquipProtectionMateMACAddr 1.3.6.1.4.1.2281.10.1.6.4
In case of 1+1 protection it is protected card (Mate) MAC address In case of 2+2 protection it is the IP address of the protected unit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  MacAddress  

genEquipProtectionRadioExcessiveBERSwitch 1.3.6.1.4.1.2281.10.1.6.5
The Admin state of an Excessive BER threshold. When enabled, crossing the Excessive BER threshold will cause a protection switch.
Status: mandatory Access: read-write
OBJECT-TYPE    
  EnableDisable  

genEquipProtectionLockout 1.3.6.1.4.1.2281.10.1.6.6
This parameter provides the ability to lock the mode of each card in the protection, meaning to force the fact that protection switch will not occur.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OffOn  

genEquipProtectionForceSwitch 1.3.6.1.4.1.2281.10.1.6.7
This parameter is a command that forces a protection switch regardless of the state of the standby card.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OffOn  

genEquipProtectionManualSwitch 1.3.6.1.4.1.2281.10.1.6.8
This parameter is a command that performs manaual protection switch.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OffOn  

genEquipProtectionCopyToMateComand 1.3.6.1.4.1.2281.10.1.6.9
Setting this parameter to On will copy configured parameters from the active to the standby unit.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OffOn  

genEquipProtectionCopyToMateStatus 1.3.6.1.4.1.2281.10.1.6.10
This parameter represents the status of the copy-to-mate command when protection is enabled. - ready(0) - inProgress(1), - success(2), - failure(3)
Status: mandatory Access: read-only
OBJECT-TYPE    
  ProgressStatus  

genEquipProtectionMultiUnitLAGAdmin 1.3.6.1.4.1.2281.10.1.6.11
This parameter enables the Multi Unit LAG feature. It can be activated only in Single Pipe configuration and only when protection is active (either 1+1 or 2+2).
Status: mandatory Access: read-write
OBJECT-TYPE    
  EnableDisable  

genEquipProtectionRevertiveAdmin 1.3.6.1.4.1.2281.10.1.6.12
Enable/Disable revertive protection mode. In revertive protection mode one IDU will be defined as a Primary and the other will be Secondary. Revertive protection will always tend to make the Primary IDU active unless it has a hardware failure.
Status: mandatory Access: read-write
OBJECT-TYPE    
  EnableDisable  

genEquipProtectionRevertivePrimaryIDU 1.3.6.1.4.1.2281.10.1.6.13
Decides whether upper or lower IDU will be primary. When placed in a shelf, the upper will be the upper slot in the shelf. When working in stand-alone mode, the IDU with the highest IP address will be considered as upper.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER lower(0), upper(1)  

genEquipProtectionRevertiveMinTimer 1.3.6.1.4.1.2281.10.1.6.14
Minimal revertive protection timer period.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..30  

genEquipProtectionRevertiveMaxNumOfTries 1.3.6.1.4.1.2281.10.1.6.15
Maximal number of revertive protection tries. Used to prevent instability. Revertive protection will give up trying to switch to the primary standby IDU path after the maximal number of tries. Setting Zero value will enable revertive protection switch only if the last protection switch was due to a local equipment failure.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..10  

genEquipProtectionRevertiveTimerMultiplier 1.3.6.1.4.1.2281.10.1.6.16
A factor that increases the revertive timer period after each try. Setting 1 value will leave the timer period constantly at its minimal value.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..10  

genEquipProtectionAspRevertive 1.3.6.1.4.1.2281.10.1.6.17
n Smart Pipe HSB mode , this parameter causes the Ethernet line port to be muted upon a complete failure of the radio signal (in both active and standby units)
Status: mandatory Access: read-write
OBJECT-TYPE    
  EnableDisable  

genEquipDiversity 1.3.6.1.4.1.2281.10.1.7
OBJECT IDENTIFIER    

genEquipDiversityType 1.3.6.1.4.1.2281.10.1.7.1
this parameter sets the type of hitless diversity to be used. Notice that only if protection is enabled this has any effect.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), space-diversity(2), frequency-diversity(3)  

genEquipDiversityRevertiveMode 1.3.6.1.4.1.2281.10.1.7.2
this parameter sets whether hitless switches are revertive in the event that the primary radio channel doesn't have any errors.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER non-revertive(1), revertive(2)  

genEquipDiversityPrimaryRadio 1.3.6.1.4.1.2281.10.1.7.3
this parameter sets which IDU contains the primary radio channel to revert to.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER upper-radio(1), lower-radio(2)  

genEquipDiversityRevertiveTimer 1.3.6.1.4.1.2281.10.1.7.4
This parameter sets the amount of seconds that must pass without a failure in the primary radio before doing a revertive switch.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..15  

genEquipDiversityForceActive 1.3.6.1.4.1.2281.10.1.7.5
This parameter allows forcing incoming traffic to be taken from either of the radios (or none) for testing purposes.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(0), local-radio(1), mate-radio(2)  

genEquipDiversitySwitchCounter 1.3.6.1.4.1.2281.10.1.7.6
This parameter shows the number of hitless switches performed since last time counter was cleared.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipDiversitySwitchCounterClear 1.3.6.1.4.1.2281.10.1.7.7
This parameter allows clearing of switch counter.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OffOn  

genEquipDiversityReceiveRadio 1.3.6.1.4.1.2281.10.1.7.8
This parameter shows from which radio the traffic is currently being taken.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER lower-idu(0), upper-idu(1)  

genEquipFault 1.3.6.1.4.1.2281.10.3
OBJECT IDENTIFIER    

genEquipCurrentAlarm 1.3.6.1.4.1.2281.10.3.1
OBJECT IDENTIFIER    

genEquipCurrentAlarmLastChangeCounter 1.3.6.1.4.1.2281.10.3.1.1
This counter is initialized with a random number after resest, and incremented on each change in the CurrentAlarmTable
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipCurrentAlarmTable 1.3.6.1.4.1.2281.10.3.1.2
This table includes the current alarm (when a RAISED trap is sent, an alarm is added to the table, when a CLEAR trap is sent, the alarm is removed).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipCurrentAlarmEntry

genEquipCurrentAlarmEntry 1.3.6.1.4.1.2281.10.3.1.2.1
Entry containing the info of current RAISED traps.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipCurrentAlarmEntry  

genEquipCurrentAlarmCounter 1.3.6.1.4.1.2281.10.3.1.2.1.1
A running counter of open alarms, incremented upon each new alarm.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipCurrentAlarmRaisedTimeT 1.3.6.1.4.1.2281.10.3.1.2.1.2
The rasied time of this alarm. Time in seconds since January 1, 1970 00:00 UTC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipCurrentAlarmId 1.3.6.1.4.1.2281.10.3.1.2.1.3
Alarm ID. List of alarm IDs is available in the MIB Ref. Guide.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipCurrentAlarmName 1.3.6.1.4.1.2281.10.3.1.2.1.4
Alarm name (the parameter and entity in the CLI) for example 'radio/framer/radio-lof'
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipCurrentAlarmInstance 1.3.6.1.4.1.2281.10.3.1.2.1.5
In the case of alarms that may have several appereances (at interfaces, channels, VCs, etc.), this parameter indicates the instance of the alarm.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipCurrentAlarmSeverity 1.3.6.1.4.1.2281.10.3.1.2.1.6
The current Alarm severity the values can be: - indeterminate(0) - critical(1) - major(2) - minor(3) - warning(4) - cleared(5)
Status: mandatory Access: read-only
OBJECT-TYPE    
  Severity  

genEquipCurrentAlarmIfIndex 1.3.6.1.4.1.2281.10.3.1.2.1.7
Interface Index where the alarm occurred, alarms that are not associated with specific interfaces will have the following value: For a non-interface alarm, the value is: 65001
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipCurrentAlarmModule 1.3.6.1.4.1.2281.10.3.1.2.1.8
The module of the alarm. Possible values are 'IDU' or 'RFU'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipCurrentAlarmDesc 1.3.6.1.4.1.2281.10.3.1.2.1.9
The alarm description (same as the description in the sent trap).
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipCurrentAlarmProbableCause 1.3.6.1.4.1.2281.10.3.1.2.1.10
The alarm probable cause.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipCurrentAlarmCorrectiveActions 1.3.6.1.4.1.2281.10.3.1.2.1.11
The alarm corrective actions.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipCurrentAlarmState 1.3.6.1.4.1.2281.10.3.1.2.1.12
The state of the alarm (cleared or rasied).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER cleared(0), raised(1), event(2)  

genEquipCurrentAlarmSlotId 1.3.6.1.4.1.2281.10.3.1.2.1.13
The ID of the slot originating the alarm.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SlotId  

genEquipCurrentAlarmAdditionalInfo 1.3.6.1.4.1.2281.10.3.1.2.1.14
Additional information that may further qualify the source of the alarm.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipCurrentAlarmUserText 1.3.6.1.4.1.2281.10.3.1.2.1.15
An additional description of the event or fault, or any other information that user wants to attach to it.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipMostSevereAlarm 1.3.6.1.4.1.2281.10.3.1.3
The severity of the most severe alarm in the system
Status: mandatory Access: read-only
OBJECT-TYPE    
  Severity  

genEquipAlarmConfigDefault 1.3.6.1.4.1.2281.10.3.1.4
Allows to revert back to the default values of all alarm configurations
Status: mandatory Access: read-write
OBJECT-TYPE    
  OffOn  

genEquipAlarmConfigTable 1.3.6.1.4.1.2281.10.3.1.5
This table allows system alarms configuration.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipAlarmConfigEntry

genEquipAlarmConfigEntry 1.3.6.1.4.1.2281.10.3.1.5.1
This table entry allows system alarms configuration.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipAlarmConfigEntry  

genEquipAlarmConfigId 1.3.6.1.4.1.2281.10.3.1.5.1.1
he alarm unique Id number that identifies it.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipAlarmConfigSeverity 1.3.6.1.4.1.2281.10.3.1.5.1.2
The perceived severity of the raised alarm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Severity  

genEquipAlarmConfigDescr 1.3.6.1.4.1.2281.10.3.1.5.1.3
The description of the raised alarm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipAlarmConfigAdditionalText 1.3.6.1.4.1.2281.10.3.1.5.1.4
An additional description of the fault, or any other information that user wants to attach to it.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipAlarmServiceAffect 1.3.6.1.4.1.2281.10.3.1.5.1.5
Indicates whether the raised alarm affects a service.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OffOn  

genEquipTrapCfg 1.3.6.1.4.1.2281.10.3.2
OBJECT IDENTIFIER    

genEquipTrapCfgMgrTable 1.3.6.1.4.1.2281.10.3.2.1
This table indicates the Trap manager list.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipTrapCfgMgrEntry

genEquipTrapCfgMgrEntry 1.3.6.1.4.1.2281.10.3.2.1.1
Entry containing the manager IP addresses and the trap filter options.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipTrapCfgMgrEntry  

genEquipTrapCfgMgrId 1.3.6.1.4.1.2281.10.3.2.1.1.1
This value indicates an index of a specific manager
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipTrapCfgMgrAdmin 1.3.6.1.4.1.2281.10.3.2.1.1.2
This value indicates an administrative state of a specific manager. disable - will not send traps to this trap manager.
Status: mandatory Access: read-write
OBJECT-TYPE    
  EnableDisable  

genEquipTrapCfgMgrIP 1.3.6.1.4.1.2281.10.3.2.1.1.3
This value indicates the manager's IP address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

genEquipTrapCfgMgrPort 1.3.6.1.4.1.2281.10.3.2.1.1.4
The Port for sending the trap for each manager (possible values: 70-65535)
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 70..65535  

genEquipTrapCfgMgrName 1.3.6.1.4.1.2281.10.3.2.1.1.5
The name of the manager configured to receive the traps
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..30)  

genEquipTrapCfgMgrCommunity 1.3.6.1.4.1.2281.10.3.2.1.1.6
The manager trap community configured.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..30)  

genEquipTrapCfgMgrSeverityFilter 1.3.6.1.4.1.2281.10.3.2.1.1.7
This is a bit mask value for masking traps according to its severity. There is a bit for each severity. If the relevant bit is on (1), the Agent will send traps with this severity. It won't send traps if the bit is off (0). The list of bits from LSB to MSB: Bit 1 (LSB) - indeterminate Bit 2 - critical Bit 3 - major Bit 4 - minor Bit 5 - warning Bit 6 - cleared
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

genEquipTrapCfgMgrStatusChangeFilter 1.3.6.1.4.1.2281.10.3.2.1.1.8
This value represents the mode in which the traps are sent: If the filter is set to ON - only traps that change the severity of the system are sent. If the filter is set to OFF - all traps (that are not screened by other filters) are sent.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OffOn  

genEquipTrapCfgMgrCLLI 1.3.6.1.4.1.2281.10.3.2.1.1.9
Common Language Location Identifier (maximum length: 100 chars)
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..100)  

genEquipTrapCfgMgrHeartbeatPeriod 1.3.6.1.4.1.2281.10.3.2.1.1.10
This item defines the interval (in minutes) between each heartbeat trap. A value of '0' disables this feature.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..1440  

genEquipTrapCfgMgrIPv6 1.3.6.1.4.1.2281.10.3.2.1.1.11
The IP-v6 address of the trap manage)
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

genEquipTrapCfgMgrV3User 1.3.6.1.4.1.2281.10.3.2.1.1.12
The manager trap V3 user name configured
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipEventLog 1.3.6.1.4.1.2281.10.3.3
OBJECT IDENTIFIER    

genEquipEventLogTable 1.3.6.1.4.1.2281.10.3.3.1
This table includes the event log.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipEventLogEntry

genEquipEventLogEntry 1.3.6.1.4.1.2281.10.3.3.1.1
Entry containing the info of the event log table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipEventLogEntry  

genEquipEventLogCounter 1.3.6.1.4.1.2281.10.3.3.1.1.1
The event counter.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipEventLogRaisedTimeT 1.3.6.1.4.1.2281.10.3.3.1.1.2
The rasied time of this event. Time in seconds since January 1, 1970 00:00 UTC. (time_t format)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipEventLogSeverity 1.3.6.1.4.1.2281.10.3.3.1.1.3
The event severity, possible values are: - indeterminate(0), - critical(1) - major(2) - minor(3) - warning(4) - cleared(5)
Status: mandatory Access: read-only
OBJECT-TYPE    
  Severity  

genEquipEventLogModule 1.3.6.1.4.1.2281.10.3.3.1.1.4
The module of the event. ('IDU' or 'RFU')
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipEventLogDesc 1.3.6.1.4.1.2281.10.3.3.1.1.5
The event description (same as the description in the sent trap).
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipEventLogState 1.3.6.1.4.1.2281.10.3.3.1.1.6
The state of the event or alarm. In case of alarm, 'cleard' or 'raised'. In case of event, 'event'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER cleared(0), raised(1), event(2)  

genEquipEventLogProbableCause 1.3.6.1.4.1.2281.10.3.3.1.1.7
The probable cause that may be the reason for the event.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipEventLogCorrectiveActions 1.3.6.1.4.1.2281.10.3.3.1.1.8
Some possible suggested corrective actions in order to eliminate the raised alarm.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipEventLogAdditionalInfo 1.3.6.1.4.1.2281.10.3.3.1.1.9
Additional information that may further qualify the source of the event.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipEventLogUserText 1.3.6.1.4.1.2281.10.3.3.1.1.10
An additional description of the event or fault, or any other information that user wants to attach to it.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipEventLogIfIndex 1.3.6.1.4.1.2281.10.3.3.1.1.11
If Index of the originated source.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipEventLogId 1.3.6.1.4.1.2281.10.3.3.1.1.12
The Id of the event.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipEventLogClear 1.3.6.1.4.1.2281.10.3.3.2
The clear event log command. If enabled, will clear the event log.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OffOn  

genEquipEventLogLastChangeCounter 1.3.6.1.4.1.2281.10.3.3.3
This counter is initialized with a random number after reset, and incremented on each change in the EventLogTable
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipFaultErrno 1.3.6.1.4.1.2281.10.3.4
The application last error number. List of Errnos are located in the MIB Ref Guide.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipFaultErrDescr 1.3.6.1.4.1.2281.10.3.5
The application last error description. List of Errnos are located in the MIB Ref Guide.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipMng 1.3.6.1.4.1.2281.10.4
OBJECT IDENTIFIER    

genEquipMngSw 1.3.6.1.4.1.2281.10.4.1
OBJECT IDENTIFIER    

genEquipMngSwServerUrl 1.3.6.1.4.1.2281.10.4.1.1
Remote SW Update Server URL where SW updates reside
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipMngSwServerLogin 1.3.6.1.4.1.2281.10.4.1.2
Remote server login
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipMngSwServerPassword 1.3.6.1.4.1.2281.10.4.1.3
Remote server password
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipMngSwProxyUrl 1.3.6.1.4.1.2281.10.4.1.4
Proxy Server Url. This parameter is obsolete and should not be in used.
Status: obsolete Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipMngSwProxyLogin 1.3.6.1.4.1.2281.10.4.1.5
Proxy server login This parameter is obsolete and should not be in used.
Status: obsolete Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipMngSwProxyPassword 1.3.6.1.4.1.2281.10.4.1.6
Proxy server password This parameter is obsolete and should not be in used.
Status: obsolete Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipMngSwDownloadStatus 1.3.6.1.4.1.2281.10.4.1.7
Download software status. Possible values are: - ready(0) - inProgress(1) - success(2) - failure(3)
Status: mandatory Access: read-only
OBJECT-TYPE    
  ProgressStatus  

genEquipMngSwInstallStatus 1.3.6.1.4.1.2281.10.4.1.8
Install software status. Possible values are: - ready(0) - inProgress(1) - success(2) - failure(3)
Status: mandatory Access: read-only
OBJECT-TYPE    
  ProgressStatus  

genEquipMngSwCommand 1.3.6.1.4.1.2281.10.4.1.9
The command that is executed to manage SW versions. Depending on the value given, a different operation will be carried out involving FTP and/or version installing. Notice that software will be installed in all slots in a shelf and reset will be automatically carried out at the end of the installation process. Possible values are: - noOperation(0) - downloadUpgradeVersion(1) - load a newer version from FTP site - upgrade(2) - upgrade to newer version which has already been loaded - rollback(3) - install a previously working version without downloading - downgrade(4) - downgrade to an older version which has alredy been loaded - downloadDowngradeVersion(5) - load an older version from FTP site - upgradeTimer(6) - Starts the timer defined in genEquipMngSwInstallationTimer and upon expiration upgrades to a newer version which has already been loaded. - rollbackTimer(7) - Starts the timer defined in genEquipMngSwInstallationTimer and upon expiration install a previously working version without downloading - downgradeTimer(7) - Starts the timer defined in genEquipMngSwInstallationTimer and upon expiration downgrades to an older which has already been loaded - abortTimedTnstallation(9) stops a counting timer; the installation process will not take place. Notice that it does not stop an installation process once started.
Status: mandatory Access: read-write
OBJECT-TYPE    
  SwCommandTimer  

genEquipMngSwInstalledIduVersion 1.3.6.1.4.1.2281.10.4.1.10
This value indicates the Package Version of the installed IDU SW
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipMngSwInstalledRfuVersion 1.3.6.1.4.1.2281.10.4.1.11
This value indicates the Package version of the installed RFU SW.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipMngSwVersions 1.3.6.1.4.1.2281.10.4.1.13
OBJECT IDENTIFIER    

genEquipMngSwIDUVersionsTable 1.3.6.1.4.1.2281.10.4.1.13.1
This table contains all IDU running versions.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipMngSwIDUVersionsEntry

genEquipMngSwIDUVersionsEntry 1.3.6.1.4.1.2281.10.4.1.13.1.1
Entry containing the info of the IDU Versions table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipMngSwIDUVersionsEntry  

genEquipMngSwIDUVersionsCounter 1.3.6.1.4.1.2281.10.4.1.13.1.1.1
This is the index of this table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipMngSwIDUVersionsPackageName 1.3.6.1.4.1.2281.10.4.1.13.1.1.2
The package name
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipMngSwIDUVersionsTargetDevice 1.3.6.1.4.1.2281.10.4.1.13.1.1.3
The Target device within the NE (i.e. Modem, FPGA, IDU)
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipMngSwIDUVersionsRunningVersion 1.3.6.1.4.1.2281.10.4.1.13.1.1.4
The running version.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipMngSwIDUVersionsInstalledVersion 1.3.6.1.4.1.2281.10.4.1.13.1.1.5
The installed version is similar to the running version, besides packages that are not currently running. Those packages will have in the running version 'N/A' while in the installed version there is a version number. For example, in equipment without daughter-board, some of the packages will be installed but not running.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipMngSwIDUVersionsUpgradePackage 1.3.6.1.4.1.2281.10.4.1.13.1.1.6
In case the user performs an upgrade, this version will be the running/installed version
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipMngSwIDUVersionsDowngradePackage 1.3.6.1.4.1.2281.10.4.1.13.1.1.7
In case the user performs downgrade, this version will be the running/installed version.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipMngSwIDUVersionsResetType 1.3.6.1.4.1.2281.10.4.1.13.1.1.8
Minimum level of reset required to update the software in the relevant module.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER noReset(0), appWarmReset(1), tccColdReset(2), mainBoardColdReset(3), mainBoardWarmReset(4), applicationRestart(5), cardReset(6), notApplicable(7)  

genEquipMngSwTimerTable 1.3.6.1.4.1.2281.10.4.1.13.2
This table contains all IDU running versions.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipMngSwTimerEntry

genEquipMngSwTimerEntry 1.3.6.1.4.1.2281.10.4.1.13.2.1
Entry containing the info of the IDU Versions table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipMngSwTimerEntry  

genEquipMngSwTimerSlotNumber 1.3.6.1.4.1.2281.10.4.1.13.2.1.1
The slot ID of the unit for this timer; 0 is for stand-alone units.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..6  

genEquipMngSwTimerInstallationTimer 1.3.6.1.4.1.2281.10.4.1.13.2.1.2
The timer (in minutes) for software installation operations to this unit.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..1440  

genEquipMngSwTimerTimeToInstall 1.3.6.1.4.1.2281.10.4.1.13.2.1.3
The amount of time (in seconds) from now for the unit to perform software installation. Zero denotes that no operation has been requested.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..86400  

genEquipMngSwTimerTimerAbort 1.3.6.1.4.1.2281.10.4.1.13.2.1.4
This parameter is used to stop the count-down to the software update action.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER proceed(0), abort(1)  

genEquipMngSwFTPTimer 1.3.6.1.4.1.2281.10.4.1.13.10
Time (in seconds) until file transfer is failed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

genEquipMngSwInstallationTimer 1.3.6.1.4.1.2281.10.4.1.14
The timer (in minutes) for timed software installation operations to this unit
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..1440  

genEquipMngSwTimeToInstall 1.3.6.1.4.1.2281.10.4.1.15
The amount of time (in minutes) from now for the unit to perform software installation. Zero denotes that no operation has been requested
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1440  

genEquipMngSwUpgradeCommonRfuVersion 1.3.6.1.4.1.2281.10.4.1.16
This value indicates the Package version of the installed RFU SW.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipMngSwDowngradeCommonRfuVersion 1.3.6.1.4.1.2281.10.4.1.17
This value indicates the Package version of the installed RFU SW.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipMngSwFileTransferTable 1.3.6.1.4.1.2281.10.4.1.18
This table allows configuring the details of the external server where software versions should be located.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipMngSwFileTransferEntry

genEquipMngSwFileTransferEntry 1.3.6.1.4.1.2281.10.4.1.18.1
Entry containing the info of software management file transfer.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipMngSwFileTransferEntry  

genEquipMngSwFileTransferIndex 1.3.6.1.4.1.2281.10.4.1.18.1.1
The index of the table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipMngSwFileTransferProtocol 1.3.6.1.4.1.2281.10.4.1.18.1.2
The protocol to use to transfer the files between the system and an external computer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  FtpProtocolType  

genEquipMngSwFileTransferUserName 1.3.6.1.4.1.2281.10.4.1.18.1.3
User name for access to the configuration files location.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipMngSwFileTransferPassword 1.3.6.1.4.1.2281.10.4.1.18.1.4
Password for access to the software version files location.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipMngSwFileTransferAddress 1.3.6.1.4.1.2281.10.4.1.18.1.5
IP address of the computer where software version files are to be taken from.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

genEquipMngSwFileTransferPath 1.3.6.1.4.1.2281.10.4.1.18.1.6
Location of the files in the external server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipMngSwFileTransferIpv6Address 1.3.6.1.4.1.2281.10.4.1.18.1.7
IPv6 Server Address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

genEquipSecurityTrafficCrypto 1.3.6.1.4.1.2281.10.11.10
OBJECT IDENTIFIER    

genEquipSecurityFipsAdmin 1.3.6.1.4.1.2281.10.11.10.1
FIPS admin configuration parameter
Status: mandatory Access: read-write
OBJECT-TYPE    
  EnableDisable  

genEquipSecurityFipsStatus 1.3.6.1.4.1.2281.10.11.10.2
FIPS operational status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DownUp  

genEquipTrafficCryptoConfigTable 1.3.6.1.4.1.2281.10.11.10.10
Traffic Crypto configuration table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipTrafficCryptoConfigEntry

genEquipTrafficCryptoConfigEntry 1.3.6.1.4.1.2281.10.11.10.10.1
Traffic Crypto configuration table entry
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipTrafficCryptoConfigEntry  

genEquipTrafficCryptoConfigId 1.3.6.1.4.1.2281.10.11.10.10.1.1
Traffic crypto Configuration Intreface ID
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipTrafficCryptoConfigConfigAdmin 1.3.6.1.4.1.2281.10.11.10.10.1.2
Traffic Crypto Admin Mode.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), aes-256(1)  

genEquipTrafficCryptoConfigMkey 1.3.6.1.4.1.2281.10.11.10.10.1.3
Traffic Crypto Master Key.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

genEquipTrafficCryptoConfigBackupMkey 1.3.6.1.4.1.2281.10.11.10.10.1.4
Traffic Crypto Backup Master Key
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

genEquipTrafficCryptoConfigMkeyPeriod 1.3.6.1.4.1.2281.10.11.10.10.1.5
Master Key Expire Configuration.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

genEquipTrafficCryptoConfigRandKeyGen 1.3.6.1.4.1.2281.10.11.10.10.1.6
Random Key generation/clear indication.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER random-key-generate(0), random-key-clear(1)  

genEquipTrafficCryptoConfigSkeyPeriod 1.3.6.1.4.1.2281.10.11.10.10.1.7
Session Key Update Time Configuration.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

genEquipTrafficCryptoStatusTable 1.3.6.1.4.1.2281.10.11.10.11
Traffic Crypto status table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipTrafficCryptoStatusEntry

genEquipTrafficCryptoStatusEntry 1.3.6.1.4.1.2281.10.11.10.11.1
Traffic Crypto status table Entry
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipTrafficCryptoStatusEntry  

genEquipTrafficCryptoStatusId 1.3.6.1.4.1.2281.10.11.10.11.1.1
Traffic Crypto Status Intreface ID
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipTrafficCryptoStatusValid 1.3.6.1.4.1.2281.10.11.10.11.1.2
Crypto Interface Validation State.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER not-valid(0), valid(1)  

genEquipTrafficCryptoStatusMkeyTimeExpire 1.3.6.1.4.1.2281.10.11.10.11.1.3
Number of days Mkey to expire.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipMngSwFileTransferStatusTable 1.3.6.1.4.1.2281.10.4.1.19
This table shows the status of the current software version file transfer operation.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipMngSwFileTransferStatusEntry

genEquipMngSwFileTransferStatusEntry 1.3.6.1.4.1.2281.10.4.1.19.1
Entry containing the info of software management file transfer status.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipMngSwFileTransferStatusEntry  

genEquipMngSwFileTransferStatusIndex 1.3.6.1.4.1.2281.10.4.1.19.1.1
The index of the table..
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipMngSwFileTransferStatusResult 1.3.6.1.4.1.2281.10.4.1.19.1.2
Status of the current file transfer operation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ready(0), downloadStarted(1), verifyingDownloadFiles(2), downloadInProgress(3), downloadSuccess(4), downloadFailure(5), allComponentsExist(6), versionIncompatibleWithSystem(7), incompleteFileSet(8), componentUnsupportedByHw(9), corruptSwFiles(10), missingDependencies(11), downloadCancelled(12)  

genEquipMngSwFileTransferPercentageDone 1.3.6.1.4.1.2281.10.4.1.19.1.3
An indication of the progress of the process of the current file transfer operation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

genEquipMngSwFileTransferPercentageDoneStandBy 1.3.6.1.4.1.2281.10.4.1.19.1.4
An indication of the progress of the process of the current internal file transfer operation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

genEquipMngSwFileTransferStatusResultStandBy 1.3.6.1.4.1.2281.10.4.1.19.1.5
Status of the current internal file transfer operation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ready(0), download-started(1), verifying-download-files(2)  

genEquipMngSwInstallStatusTable 1.3.6.1.4.1.2281.10.4.1.20
This table shows the status of the current software version installation operation.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipMngSwInstallStatusEntry

genEquipMngSwInstallStatusEntry 1.3.6.1.4.1.2281.10.4.1.20.1
Entry containing the info of software installation status.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipMngSwInstallStatusEntry  

genEquipMngSwInstallStatusIndex 1.3.6.1.4.1.2281.10.4.1.20.1.1
The index of the table..
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipMngSwInstallStatusResult 1.3.6.1.4.1.2281.10.4.1.20.1.2
Status of the current installation operation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ready(0), installationStarted(1), verifyingInstallationFiles(2), installationInProgress(3), installationSuccess(4), installationPartialSuccess(5), installationFailure(6), incompleteSwVersion(7), installationCancelled(8)  

genEquipMngSwInstallPercentageDone 1.3.6.1.4.1.2281.10.4.1.20.1.3
An indication of the progress of the process of the current installation operation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

genEquipMngSwInstallStatusResultStandBy 1.3.6.1.4.1.2281.10.4.1.20.1.4
Status of the current file transfer operation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ready(0), installationStarted(1), verifyingInstallationFiles(2), installationInProgress(3), installationSuccess(4), installationPartialSuccess(5), installationFailure(6), incompleteSwVersion(7), installationCancelled(8)  

genEquipMngSwInstallPercentageDoneStandBy 1.3.6.1.4.1.2281.10.4.1.20.1.5
An indication of the progress of the process of the current installation operation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

genEquipMngSwOperationTable 1.3.6.1.4.1.2281.10.4.1.21
This table allows downloading and installing SW versions.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipMngSwOperationEntry

genEquipMngSwOperationEntry 1.3.6.1.4.1.2281.10.4.1.21.1
Entry containing the info of software management operation table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipMngSwOperationEntry  

genEquipMngSwOperationIndex 1.3.6.1.4.1.2281.10.4.1.21.1.1
The index of the table..
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipMngSwOperationOperation 1.3.6.1.4.1.2281.10.4.1.21.1.2
The operation to be performed: download, install, update backup, swap boot section, abort installation timer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noAction(0), download(1), install(2), updateBackup(3), swapBootSection(4), abortTimer(5)  

genEquipMngSwOperationTimedInstallation 1.3.6.1.4.1.2281.10.4.1.21.1.3
Whether to perform the installation after a configurable timer expires.
Status: mandatory Access: read-write
OBJECT-TYPE    
  NoYes  

genEquipMngSwSlotRunningVersionTable 1.3.6.1.4.1.2281.10.4.1.22
This table shows the versions currently running in cards installed in the system.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipMngSwSlotRunningVersionEntry

genEquipMngSwSlotRunningVersionEntry 1.3.6.1.4.1.2281.10.4.1.22.1
This table entry shows the versions currently running in cards installed in the system.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipMngSwSlotRunningVersionEntry  

genEquipMngSwSlotRunningVersionSlotId 1.3.6.1.4.1.2281.10.4.1.22.1.1
The index of the table..
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..12  

genEquipMngSwSlotRunningVersionCardType 1.3.6.1.4.1.2281.10.4.1.22.1.2
Type of card inserted in slot.
Status: mandatory Access: read-only
OBJECT-TYPE    
  InventoryCardType  

genEquipMngSwSlotRunningVersionComponent 1.3.6.1.4.1.2281.10.4.1.22.1.3
Name of SW functional component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipMngSwSlotRunningVersionActualVersion 1.3.6.1.4.1.2281.10.4.1.22.1.4
Version of running SW.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipMngSwIDUVersionsStandByTable 1.3.6.1.4.1.2281.10.4.1.23
This table shows the software versions residing in the standby unit.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipMngSwIDUVersionsStandByEntry

genEquipMngSwIDUVersionsStandByEntry 1.3.6.1.4.1.2281.10.4.1.23.1
This table entry shows the software versions residing in the standby unit.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipMngSwIDUVersionsStandByEntry  

genEquipMngSwIDUVersionsStandByIndex 1.3.6.1.4.1.2281.10.4.1.23.1.1
mate rpm index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipMngSwIDUVersionsStandByPackageName 1.3.6.1.4.1.2281.10.4.1.23.1.2
Name of the module which the software package belongs to.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipMngSwIDUVersionsStandByRunningVersion 1.3.6.1.4.1.2281.10.4.1.23.1.3
Version currently running.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipMngSwIDUVersionsStandByInstalledVersion 1.3.6.1.4.1.2281.10.4.1.23.1.4
Currently installed version; upon the appropriate reset this will become the running version.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipMngSwIDUVersionsStandByTargetDevice 1.3.6.1.4.1.2281.10.4.1.23.1.5
The HW board in which the SW module from the mate is running.
Status: mandatory Access: read-only
OBJECT-TYPE    
  InventoryCardType  

genEquipMngSwIDUVersionsStandByDownloadedPackage 1.3.6.1.4.1.2281.10.4.1.23.1.6
Version that was downloaded from server upon installation, it will become the installed version.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipMngSwIDUVersionsStandByResetType 1.3.6.1.4.1.2281.10.4.1.23.1.7
Minimum level of reset required to update the software in the relevant module.
Status: mandatory Access: read-only
OBJECT-TYPE    
  VmResetType  

genEquipMngSwWatchdogAdmin 1.3.6.1.4.1.2281.10.4.1.35
Enables/Disables the watchdog timer for the application.
Status: mandatory Access: read-write
OBJECT-TYPE    
  EnableDisable  

genEquipMngCfg 1.3.6.1.4.1.2281.10.4.2
OBJECT IDENTIFIER    

genEquipMngCfgBackupStatus 1.3.6.1.4.1.2281.10.4.2.1
This parameter shows the current state of the configuration backup files creation in the IDU. Possible values are: - ready(0) - inProgress(1) - success(2) - failure(3)
Status: mandatory Access: read-only
OBJECT-TYPE    
  ProgressStatus  

genEquipMngCfgRestoreStatus 1.3.6.1.4.1.2281.10.4.2.2
This parameter shows the current state of configuration restoring from downloaded backup files. Possible values are: - ready(0) - inProgress(1) - success(2) - failure(3)
Status: mandatory Access: read-only
OBJECT-TYPE    
  ProgressStatus  

genEquipMngCfgUploadStatus 1.3.6.1.4.1.2281.10.4.2.3
This parameter shows the current state of configuration backup files transfer from IDU to external FTP site. Possible values are: - ready(0) - inProgress(1) - success(2) - failure(3)
Status: mandatory Access: read-only
OBJECT-TYPE    
  ProgressStatus  

genEquipMngCfgDownloadStatus 1.3.6.1.4.1.2281.10.4.2.4
This parameter shows the current state of configuration backup files transfer from external FTP site to IDU. Possible values are: - ready(0) - inProgress(1) - success(2) - failure(3)
Status: mandatory Access: read-only
OBJECT-TYPE    
  ProgressStatus  

genEquipMngCfgCommand 1.3.6.1.4.1.2281.10.4.2.5
The command to be executed to backup/restore or upload/download configuration. If there is more then 1 slot in the NE, it is done for all the shelf.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no-operation(0), backup(1), restore(2), upload(3), download(4)  

genEquipMngCfgEthernetSwitchStoreConfiguration 1.3.6.1.4.1.2281.10.4.2.6
This parameter writes the current configuration in the database. This command should be called after any change to the following sections: - Bridge configuration - WaySide configuration - Protection configuration.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OffOn  

genEquipMngCfgSetToDefaultKeepIp 1.3.6.1.4.1.2281.10.4.2.7
Set to Default configuration without changing the network parameters such as IP address, and subnet mask.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OffOn  

genEquipMngCfgCliScriptFileName 1.3.6.1.4.1.2281.10.4.2.8
The CLI script file name to be downloaded to the NE.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipMngCfgGeneric 1.3.6.1.4.1.2281.10.4.2.10
OBJECT IDENTIFIER    

genEquipMngCfgBackupProgress 1.3.6.1.4.1.2281.10.4.2.10.1
An indication of the progress of the backup operation process.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipMngCfgTimeToInstallation 1.3.6.1.4.1.2281.10.4.2.10.2
A counter indicating the time left until installation begins.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipMngCfgFileTransferTable 1.3.6.1.4.1.2281.10.4.2.11
This table allows configuring the details of the external server where configuration should be located.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipMngCfgFileTransferEntry

genEquipMngCfgFileTransferEntry 1.3.6.1.4.1.2281.10.4.2.11.1
This table entry allows configuring the details of the external server where configuration should be located.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipMngCfgFileTransferEntry  

genEquipMngCfgFileTransferIndex 1.3.6.1.4.1.2281.10.4.2.11.1.1
Index of the table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipMngCfgFileTransferProtocol 1.3.6.1.4.1.2281.10.4.2.11.1.2
The protocol to use to transfer the files between the system and an external computer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  FtpProtocolType  

genEquipMngCfgFileTransferUserName 1.3.6.1.4.1.2281.10.4.2.11.1.3
User name for access to the configuration files location.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipMngCfgFileTransferPassword 1.3.6.1.4.1.2281.10.4.2.11.1.4
Password for access to the configuration files location.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipMngCfgFileTransferAddress 1.3.6.1.4.1.2281.10.4.2.11.1.5
IP address of the computer where configuration files are to be transferred to/from.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

genEquipMngCfgFileTransferPath 1.3.6.1.4.1.2281.10.4.2.11.1.6
Location of the files in the external server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipMngCfgFileTransferFileName 1.3.6.1.4.1.2281.10.4.2.11.1.7
Name of the file in server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipMngCfgFileTransferIpv6Address 1.3.6.1.4.1.2281.10.4.2.11.1.8
IPv6 Server's address where files will be transferred to/from.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

genEquipMngCfgFileTransferStatusTable 1.3.6.1.4.1.2281.10.4.2.12
This table shows the status of the current configuration file transfer operation.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipMngCfgFileTransferStatusEntry

genEquipMngCfgFileTransferStatusEntry 1.3.6.1.4.1.2281.10.4.2.12.1
This table entry shows the status of the current configuration file transfer operation.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipMngCfgFileTransferStatusEntry  

genEquipMngCfgFileTransferStatusIndex 1.3.6.1.4.1.2281.10.4.2.12.1.1
Index of the table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipMngCfgFileTransferStatusPercentageDone 1.3.6.1.4.1.2281.10.4.2.12.1.2
An indication of the progress of the process of the current file transfer operation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipMngCfgFileTransferStatusResult 1.3.6.1.4.1.2281.10.4.2.12.1.3
Status of the current file transfer operation.
Status: mandatory Access: read-write
OBJECT-TYPE    
  FileTransferStatus  

genEquipMngCfgOperationTable 1.3.6.1.4.1.2281.10.4.2.13
This table allows creating, restoring, transferring and deleting configuration files.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipMngCfgOperationEntry

genEquipMngCfgOperationEntry 1.3.6.1.4.1.2281.10.4.2.13.1
This table entry allows creating, restoring, transferring and deleting configuration files.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipMngCfgOperationEntry  

genEquipMngCfgOperationIndex 1.3.6.1.4.1.2281.10.4.2.13.1.1
Index of the table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipMngCfgOperationOperation 1.3.6.1.4.1.2281.10.4.2.13.1.2
The operation to be performed: backup, restore, delete, import, export.
Status: mandatory Access: read-write
OBJECT-TYPE    
  CfgOper  

genEquipMngCfgOperationFileNumber 1.3.6.1.4.1.2281.10.4.2.13.1.3
A number from 1 to 3 to identify different restoration files.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..3  

genEquipMngCfgOperationTimedInstallation 1.3.6.1.4.1.2281.10.4.2.13.1.4
Whether to install immediately or following a countdown from a defined counter.
Status: mandatory Access: read-write
OBJECT-TYPE    
  NoYes  

genEquipMngCfgOperationTimer 1.3.6.1.4.1.2281.10.4.2.13.1.5
A timer which determines the time to installation.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipMngCfgOperationSlotNumber 1.3.6.1.4.1.2281.10.4.2.13.1.6
Slot number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..12  

genEquipMngCfgConfigurationFilesTable 1.3.6.1.4.1.2281.10.4.2.14
This table shows the status of the current configuration management operation.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipMngCfgConfigurationFilesEntry

genEquipMngCfgConfigurationFilesEntry 1.3.6.1.4.1.2281.10.4.2.14.1
This table entry shows the status of the current configuration file transfer operation.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipMngCfgConfigurationFilesEntry  

genEquipMngCfgConfigurationFilesIndex 1.3.6.1.4.1.2281.10.4.2.14.1.1
Index of the table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipMngCfgConfigurationFilesFileNumber 1.3.6.1.4.1.2281.10.4.2.14.1.2
A number from 1 to 3 to identify different restoration files.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..3  

genEquipMngCfgConfigurationFilesSystemType 1.3.6.1.4.1.2281.10.4.2.14.1.3
Type of product from which the backup file was created.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipMngCfgConfigurationFilesSWVersion 1.3.6.1.4.1.2281.10.4.2.14.1.4
Software version of the system from which the backup file was created.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipMngCfgConfigurationFilesTimeDate 1.3.6.1.4.1.2281.10.4.2.14.1.5
Time and date of creation of the file.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipMngCfgConfigurationFilesSystemIP 1.3.6.1.4.1.2281.10.4.2.14.1.6
IP address of the unit from which the backup file was created.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

genEquipMngCfgConfigurationFilesCardsConfigured 1.3.6.1.4.1.2281.10.4.2.14.1.7
Types of cards for which configuration values exist in the file; when restoring other card types will get default values.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipMngCfgConfigurationFilesSystemID 1.3.6.1.4.1.2281.10.4.2.14.1.8
System ID of the unit from which the backup file was created.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipMngCfgFileRestoreStatus 1.3.6.1.4.1.2281.10.4.2.20
Status of the operation of configuration restore from restore point.
Status: mandatory Access: read-only
OBJECT-TYPE    
  FileRestoreStatus  

genEquipMngCfgFileTransferStatus 1.3.6.1.4.1.2281.10.4.2.21
Status of the operation of configuration restore from restore point.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ready(0), download-started(1), verifying-download-files(2), download-in-progress(3), download-success(4), download-failure(5), all-components-exist(6), version-incompatible-with-system(7), incomplete-file-set(8), component-unsupported-by-hw(9), corrupt-sw-files(10), missing-dependencies(11), download-cancelled(12)  

genEquipMngFileTransfer 1.3.6.1.4.1.2281.10.4.3
OBJECT IDENTIFIER    

genEquipMngFileTransferFileTypeOper 1.3.6.1.4.1.2281.10.4.3.1
Operation for the file type to be transferred between the IDU and the external server. The options with prefix 'download' are files to be transferred from the server to the IDU. The options with prefix 'upload' are files to be transferred from the IDU to the server. To download IDU certificate, the OIDs genEquipSecurityCfgSecurityFileName, genEquipSecurityCfgSecurityFileFormat and genEquipSecurityCfgSecurityFileType should be set prior the operation of download security file. To upload CSR file, the OID genEquipSecurityCfgSecurityFileName should be set prior the operation of upload CSR file. To download CLI string, the OID genEquipMngCfgCliScriptFileName should be set prior the operation of download cli-script. To download warning banner file, the OID genEquipSecurityCfgWarningBannerFName should be set prior the operation of download warning-banner.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no-operation(0), download-configuration(1), download-certificate(2), download-warning-banner(3), download-cli-script(4), upload-configuration(5), upload-csr-file(6), upload-unit-info(7)  

genEquipMngFileTransferDownloadConfigStatus 1.3.6.1.4.1.2281.10.4.3.2
The operation status of download configuration, which is performed using genEquipMngFileTransferFileTypeOper
Status: mandatory Access: read-only
OBJECT-TYPE    
  ProgressStatus  

genEquipMngFileTransferDownloadCertificateStatus 1.3.6.1.4.1.2281.10.4.3.3
The operation status of download configuration, which is performed using genEquipMngFileTransferFileTypeOper
Status: mandatory Access: read-only
OBJECT-TYPE    
  ProgressStatus  

genEquipMngFileTransferDownloadWarningBannerStatus 1.3.6.1.4.1.2281.10.4.3.4
The operation status of download warning banner, which is performed using genEquipMngFileTransferFileTypeOper
Status: mandatory Access: read-only
OBJECT-TYPE    
  ProgressStatus  

genEquipMngFileTransferDownloadCliScriptStatus 1.3.6.1.4.1.2281.10.4.3.5
TThe operation status of download cli script, which is performed using genEquipMngFileTransferFileTypeOper
Status: mandatory Access: read-only
OBJECT-TYPE    
  ProgressStatus  

genEquipMngFileTransferUploadConfigStatus 1.3.6.1.4.1.2281.10.4.3.6
The operation status of upload configuration, which is performed using genEquipMngFileTransferFileTypeOper
Status: mandatory Access: read-only
OBJECT-TYPE    
  ProgressStatus  

genEquipMngFileTransferUploadCSRStatus 1.3.6.1.4.1.2281.10.4.3.7
The operation status of upload CSR, which is performed using genEquipMngFileTransferFileTypeOper
Status: mandatory Access: read-only
OBJECT-TYPE    
  ProgressStatus  

genEquipMngFileTransferUploadUnitInfoStatus 1.3.6.1.4.1.2281.10.4.3.8
The operation status of upload unit info, which is performed using genEquipMngFileTransferFileTypeOper
Status: mandatory Access: read-only
OBJECT-TYPE    
  ProgressStatus  

genEquipMngUnitInfo 1.3.6.1.4.1.2281.10.4.4
OBJECT IDENTIFIER    

genEquipMngUnitInfoGeneric 1.3.6.1.4.1.2281.10.4.4.1
OBJECT IDENTIFIER    

genEquipMngUnitInfoOperation 1.3.6.1.4.1.2281.10.4.4.1.1
Allows creating and exporting the unit information file.
Status: mandatory Access: read-write
OBJECT-TYPE    
  CfgUnitInfoOper  

genEquipMngUnitInfoProgress 1.3.6.1.4.1.2281.10.4.4.1.2
Progress in percentage of the operation of the unit info file creation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipMngUnitInfoStatus 1.3.6.1.4.1.2281.10.4.4.1.3
Status of the operation of the unit info file creation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  ProgressStatus  

genEquipMngCli 1.3.6.1.4.1.2281.10.4.5
OBJECT IDENTIFIER    

genEquipMngCliScriptOperation 1.3.6.1.4.1.2281.10.4.5.1
Allows importing, showing, deleting and executing CLI scripts.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no-operation(0), import(1), delete(2), show(3), execute(4)  

genEquipMngCliScriptOperationStatus 1.3.6.1.4.1.2281.10.4.5.2
Allows importing, showing, deleting and executing CLI scripts.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ready(0), executing(1), failed(2), success(3)  

genEquipMngUnitInfoFileTransferTable 1.3.6.1.4.1.2281.10.4.4.2
This table allows configuring the details of the external server which the unit info file will be expoted to.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipMngUnitInfoFileTransferEntry

genEquipMngUnitInfoFileTransferEntry 1.3.6.1.4.1.2281.10.4.4.2.1
This table entry allows configuring the details of the external server which the unit info file will be expoted to.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipMngUnitInfoFileTransferEntry  

genEquipMngUnitInfoFileTransferIndex 1.3.6.1.4.1.2281.10.4.4.2.1.1
Index of the table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipMngUnitInfoFileTransferProtocol 1.3.6.1.4.1.2281.10.4.4.2.1.2
The protocol to use to transfer the files between the system and an external computer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  FtpProtocolType  

genEquipMngUnitInfoFileTransferUserName 1.3.6.1.4.1.2281.10.4.4.2.1.3
User name for access to the files location.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipMngUnitInfoFileTransferPassword 1.3.6.1.4.1.2281.10.4.4.2.1.4
Password for access to the files location.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipMngUnitInfoFileTransferAddress 1.3.6.1.4.1.2281.10.4.4.2.1.5
IP address of the computer where the files are to be transferred to/from.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

genEquipMngUnitInfoFileTransferPath 1.3.6.1.4.1.2281.10.4.4.2.1.6
Desired location of the unit info file in external server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipMngUnitInfoFileTransferFileName 1.3.6.1.4.1.2281.10.4.4.2.1.7
Name of the file in server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipMngUnitInfoFileTransferIpv6Address 1.3.6.1.4.1.2281.10.4.4.2.1.8
IPv6 Server's Address to which he file will be transferred.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

genEquipMngUnitInfoFileTransferStatusTable 1.3.6.1.4.1.2281.10.4.4.3
This table shows the status of the current configuration file transfer operation.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipMngUnitInfoFileTransferStatusEntry

genEquipMngUnitInfoFileTransferStatusEntry 1.3.6.1.4.1.2281.10.4.4.3.1
This table entry shows the status of the current configuration file transfer operation.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipMngUnitInfoFileTransferStatusEntry  

genEquipMngUnitInfoFileTransferStatusIndex 1.3.6.1.4.1.2281.10.4.4.3.1.1
Index of the table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipMngUnitInfoFileTransferStatusPercentageDone 1.3.6.1.4.1.2281.10.4.4.3.1.2
An indication of the progress of the process of the current file transfer operation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipMngUnitInfoFileTransferStatusResult 1.3.6.1.4.1.2281.10.4.4.3.1.3
Status of the current file transfer operation.
Status: mandatory Access: read-write
OBJECT-TYPE    
  ProgressStatus  

genEquipDiagAndMaintenance 1.3.6.1.4.1.2281.10.10
OBJECT IDENTIFIER    

genEquipDiagAndMaintenanceRadioLoopbackTimeout 1.3.6.1.4.1.2281.10.10.1
Radio loopback timeout, in minutes. 0 means no timer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..1440  

genEquipDiagAndMaintenanceLineLoopbackTimeout 1.3.6.1.4.1.2281.10.10.2
Line loopback timeout, in minutes. 0 means no timer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..1440  

genEquipDiagAndMaintenanceSDHLoopbackTimeout 1.3.6.1.4.1.2281.10.10.3
STM-1/OC-3 line loopback timeout, in minutes. 0 means no timer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..1440  

genEquipSecurity 1.3.6.1.4.1.2281.10.11
OBJECT IDENTIFIER    

genEquipSecurityConfiguration 1.3.6.1.4.1.2281.10.11.1
OBJECT IDENTIFIER    

genEquipSecurityCfgUploadPublicKeyStatus 1.3.6.1.4.1.2281.10.11.1.1
The upload status of the Public key.
Status: mandatory Access: read-only
OBJECT-TYPE    
  ProgressStatus  

genEquipSecurityCfgDownloadSecurityStatus 1.3.6.1.4.1.2281.10.11.1.2
The download status of the digital certificate.
Status: mandatory Access: read-only
OBJECT-TYPE    
  ProgressStatus  

genEquipSecurityCfgSecurityFileName 1.3.6.1.4.1.2281.10.11.1.3
The certificate file name to be downloaded.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipSecurityCfgSecurityFileType 1.3.6.1.4.1.2281.10.11.1.4
The digital certificate file type.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER target-certificate(0), target-ca-certificate(1)  

genEquipSecurityCfgSecurityFileFormat 1.3.6.1.4.1.2281.10.11.1.5
The certificate file format. .pem - (Privacy Enhanced Mail) Base64 encoded DER certificate, enclosed between -----BEGIN CERTIFICATE----- and -----END CERTIFICATE----- .der is a subset of Basic Encoding Rules (BER) providing for exactly one way to encode an ASN.1 value.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER pem(0), der(1)  

genEquipSecurityCfgSecurityWebCertificateAdmin 1.3.6.1.4.1.2281.10.11.1.6
The admin state of the certificate.
Status: mandatory Access: read-write
OBJECT-TYPE    
  EnableDisable  

genEquipSecurityCfgWebProtocol 1.3.6.1.4.1.2281.10.11.1.7
Use unsecure http or secure https.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER http(1), https(2)  

genEquipSecurityCfgTelnetAdmin 1.3.6.1.4.1.2281.10.11.1.8
Enable or disable the Telnet server on the NE.
Status: mandatory Access: read-write
OBJECT-TYPE    
  EnableDisable  

genEquipSecurityCfgAutoLogOutPeriod 1.3.6.1.4.1.2281.10.11.1.9
Auto logout period for CLI or web users, (1-60 seconds)
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..60  

genEquipSecurityXFTP 1.3.6.1.4.1.2281.10.11.1.10
OBJECT IDENTIFIER    

genEquipSecurityXFTPHostIP 1.3.6.1.4.1.2281.10.11.1.10.1
The FTP/SFTP host IP address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

genEquipSecurityXFTPHostPath 1.3.6.1.4.1.2281.10.11.1.10.2
The FTP/SFTP host directory path.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipSecurityXFTPProtocol 1.3.6.1.4.1.2281.10.11.1.10.3
Either FTP or SFTP to be used.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ftp(0), sftp(1)  

genEquipSecurityXFTPUserName 1.3.6.1.4.1.2281.10.11.1.10.4
FTP User name.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipSecurityXFTPPassword 1.3.6.1.4.1.2281.10.11.1.10.5
FTP User password.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipSecurityCfgPassFirstLoginChange 1.3.6.1.4.1.2281.10.11.1.11
Define whether user's first login will be required to change it password or not
Status: mandatory Access: read-write
OBJECT-TYPE    
  NoYes  

genEquipSecurityCfgCSRCreation 1.3.6.1.4.1.2281.10.11.1.12
This command create CSR file of the element. The file could be uploaded to external server by using the genEquipMngFileTransferFileTypeOper OID. The command syntax should be: . All the fields must be referred, for skipping on any field, use 'symbol instead'.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..512)  

genEquipSecurityCfgWarningBannerFName 1.3.6.1.4.1.2281.10.11.1.13
The Warning Banner file name to be downloaded to the NE.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipSecurityConfigurationRadius 1.3.6.1.4.1.2281.10.11.1.14
OBJECT IDENTIFIER    

genEquipSecurityConfigurationRadiusAdmin 1.3.6.1.4.1.2281.10.11.1.14.1
this parameter configures the admin state of the RADIUS protocol; when enabled, all users will be logged in via RADIUS server
Status: mandatory Access: read-write
OBJECT-TYPE    
  EnableDisable  

genEquipSecurityConfigurationRadiusServerIP 1.3.6.1.4.1.2281.10.11.1.14.2
this parameter configures the IP address of the RADIUS server
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

genEquipSecurityConfigurationRadiusSecret 1.3.6.1.4.1.2281.10.11.1.14.3
this parameter configures the common secret between the agent and the RADIUS server
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipSecurityConfigurationRadiusPort 1.3.6.1.4.1.2281.10.11.1.14.4
this parameter configures the IP address of UDP port used for the RADIUS protocol
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

genEquipSecurityConfigurationRadiusRetries 1.3.6.1.4.1.2281.10.11.1.14.5
this parameter configures the number of times the agent will retry to communicate with the RADIUS server before declaring the server to be unreacheable
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..10  

genEquipSecurityConfigurationRadiusTimeout 1.3.6.1.4.1.2281.10.11.1.14.6
this parameter configures the number of times the agent will retry to communicate with the RADIUS server before declaring the server to be unreacheable
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 3..30  

genEquipSecurityUsersAndGroups 1.3.6.1.4.1.2281.10.11.2
OBJECT IDENTIFIER    

genEquipSecurityUsersTable 1.3.6.1.4.1.2281.10.11.2.1
User table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipSecurityUsersEntry

genEquipSecurityUsersEntry 1.3.6.1.4.1.2281.10.11.2.1.1
User table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipSecurityUsersEntry  

genEquipSecurityUsersName 1.3.6.1.4.1.2281.10.11.2.1.1.1
This value is the user name.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipSecurityUsersPasswd 1.3.6.1.4.1.2281.10.11.2.1.1.2
This value is the user's password. It is used only in the creation phase. To change the password, you need to use the genEquipSecurityUsersAndGroupsChangePasswd command
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipSecurityUsersPriviledge 1.3.6.1.4.1.2281.10.11.2.1.1.3
This value is the users privilege.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no-privilege-lvl(-1), viewer-user-lvl(0), operator-user-lvl(1), admin-user-lvl(2), tech-user-lvl(3)  

genEquipSecurityUsersPasswdAging 1.3.6.1.4.1.2281.10.11.2.1.1.4
This value is the user's password aging time (in days). When response is 99999 the meaning is No Aging.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..90  

genEquipSecurityUsersExprDate 1.3.6.1.4.1.2281.10.11.2.1.1.5
This value is the user's password expiration date. The value is presented in time_t format. When response is -1 the meaning is Never Expired.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

genEquipSecurityUsersLastLogin 1.3.6.1.4.1.2281.10.11.2.1.1.6
This value is the user last login date. Time in seconds since January 1, 1970 00:00 UTC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipSecurityUsersRowStatus 1.3.6.1.4.1.2281.10.11.2.1.1.30
This value is the status of the entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

genEquipSecurityUsersAndGroupsChangePasswd 1.3.6.1.4.1.2281.10.11.2.2
This command changes the user password at the command line. It takes all arguments as the command. It cannot be done through the table since it needs to provide the old password as well. The format is: ' ' seperated with spaces.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipSecuritySNMP 1.3.6.1.4.1.2281.10.11.3
OBJECT IDENTIFIER    

genEquipSecuritySNMPReadCommunity 1.3.6.1.4.1.2281.10.11.3.1
This is the SNMP Read community string
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipSecuritySNMPWriteCommunity 1.3.6.1.4.1.2281.10.11.3.2
This is the SNMP Write community string
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipSecuritySNMPV3 1.3.6.1.4.1.2281.10.11.3.10
OBJECT IDENTIFIER    

genEquipSecuritySNMPV3AuthTable 1.3.6.1.4.1.2281.10.11.3.10.1
Security General File Transfer Configuration Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipSecuritySNMPV3AuthEntry

genEquipSecuritySNMPV3AuthEntry 1.3.6.1.4.1.2281.10.11.3.10.1.1
Security General File Transfer Configuration Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipSecuritySNMPV3AuthEntry  

genEquipSecuritySNMPV3AuthUserName 1.3.6.1.4.1.2281.10.11.3.10.1.1.1
This value is the V3 user name and the index of file v3 Authentication table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipSecuritySNMPV3AuthPassword 1.3.6.1.4.1.2281.10.11.3.10.1.1.2
This value is file V3 user authentication password.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipSecuritySNMPV3AuthSecurityMode 1.3.6.1.4.1.2281.10.11.3.10.1.1.3
This is the user's security mode
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noAuthNoPriv(1), authNoPriv(2), authPriv(3)  

genEquipSecuritySNMPV3AuthEncryptionMode 1.3.6.1.4.1.2281.10.11.3.10.1.1.4
This is the V3 encryption mode.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), des(2), aes(3)  

genEquipSecuritySNMPV3AuthAuthenticationAlgorithm 1.3.6.1.4.1.2281.10.11.3.10.1.1.5
This is the V3 authentication algorithm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), sha(2), md5(3)  

genEquipSecuritySNMPV3AuthAccessMode 1.3.6.1.4.1.2281.10.11.3.10.1.1.6
This is the V3 user access mode.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER readWrite(1), readOnly(2)  

genEquipSecuritySNMPV3AuthRowStatus 1.3.6.1.4.1.2281.10.11.3.10.1.1.30
This is the row status.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

genEquipSecurityGen 1.3.6.1.4.1.2281.10.11.4
OBJECT IDENTIFIER    

genEquipSecurityGenFTConfigTable 1.3.6.1.4.1.2281.10.11.4.1
Security General File Transfer Configuration Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipSecurityGenFTConfigEntry

genEquipSecurityGenFTConfigEntry 1.3.6.1.4.1.2281.10.11.4.1.1
Security General File Transfer Configuration Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipSecurityGenFTConfigEntry  

genEquipSecurityGenFTConfigIndex 1.3.6.1.4.1.2281.10.11.4.1.1.1
This value is the index of file transfer table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

genEquipSecurityGenFTConfigProtocol 1.3.6.1.4.1.2281.10.11.4.1.1.2
This value is file transfer protocol.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ftp(0), sftp(1)  

genEquipSecurityGenFTConfigUsername 1.3.6.1.4.1.2281.10.11.4.1.1.3
This value is the user's name
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipSecurityGenFTConfigPassword 1.3.6.1.4.1.2281.10.11.4.1.1.4
This value is the users password.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipSecurityGenFTConfigAddress 1.3.6.1.4.1.2281.10.11.4.1.1.5
This value is the server IP.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

genEquipSecurityGenFTConfigFilePath 1.3.6.1.4.1.2281.10.11.4.1.1.6
This value is file path.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipSecurityGenFTConfigFileName 1.3.6.1.4.1.2281.10.11.4.1.1.7
This value is the file name.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipSecurityGenFTConfigIpV6Address 1.3.6.1.4.1.2281.10.11.4.1.1.8
IP address v6 of the server, where the file are to be transferred to/from.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

genEquipSecurityGenFTStatusTable 1.3.6.1.4.1.2281.10.11.4.2
Security General File Transfer Status Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipSecurityGenFTStatusEntry

genEquipSecurityGenFTStatusEntry 1.3.6.1.4.1.2281.10.11.4.2.1
Security General File Transfer Status Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipSecurityGenFTStatusEntry  

genEquipSecurityGenFTStatusIndex 1.3.6.1.4.1.2281.10.11.4.2.1.1
This value is the index of file transfer status table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

genEquipSecurityGenFTStatusStatus 1.3.6.1.4.1.2281.10.11.4.2.1.2
File transfer operation status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  FTStatus  

genEquipSecurityGenFTStatusProgress 1.3.6.1.4.1.2281.10.11.4.2.1.3
Process prcentage
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipSecurityGenFTOperations 1.3.6.1.4.1.2281.10.11.4.11
File transfer operations
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(0), upload-security-log(1)  

genEquipSecurityGenImportExportAdmin 1.3.6.1.4.1.2281.10.11.4.12
Admin for import or export security settings
Status: mandatory Access: read-write
OBJECT-TYPE    
  EnableDisable  

genEquipSecurityAccessControl 1.3.6.1.4.1.2281.10.11.5
OBJECT IDENTIFIER    

genEquipSecurityAccessControlProfileTable 1.3.6.1.4.1.2281.10.11.5.1
Security Access Control Profile Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipSecurityAccessControlProfileEntry

genEquipSecurityAccessControlProfileEntry 1.3.6.1.4.1.2281.10.11.5.1.1
Security Access Control Profile Table Entry
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipSecurityAccessControlProfileEntry  

genEquipSecurityAccessControlProfileName 1.3.6.1.4.1.2281.10.11.5.1.1.1
User profile name.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipSecurityAccessControlProfileChannel 1.3.6.1.4.1.2281.10.11.5.1.1.2
Permitted access channels.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..127  

genEquipSecurityAccessControlProfileUsed 1.3.6.1.4.1.2281.10.11.5.1.1.3
Indicate whether the profile in used
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipSecurityAccessControlProfileSecurityWrite 1.3.6.1.4.1.2281.10.11.5.1.1.4
Security functional write access level.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RbacAccessLevel  

genEquipSecurityAccessControlProfileSecurityRead 1.3.6.1.4.1.2281.10.11.5.1.1.5
Security functional read access level.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RbacAccessLevel  

genEquipSecurityAccessControlProfileMngWrite 1.3.6.1.4.1.2281.10.11.5.1.1.6
Management functional write access level.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RbacAccessLevel  

genEquipSecurityAccessControlProfileMngRead 1.3.6.1.4.1.2281.10.11.5.1.1.7
Management functional read access level.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RbacAccessLevel  

genEquipSecurityAccessControlProfileRadioWrite 1.3.6.1.4.1.2281.10.11.5.1.1.8
Radio functional write access level.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RbacAccessLevel  

genEquipSecurityAccessControlProfileRadioRead 1.3.6.1.4.1.2281.10.11.5.1.1.9
Radio functional read access level.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RbacAccessLevel  

genEquipSecurityAccessControlProfileTDMWrite 1.3.6.1.4.1.2281.10.11.5.1.1.10
TDM functional write access level.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RbacAccessLevel  

genEquipSecurityAccessControlProfileTDMRead 1.3.6.1.4.1.2281.10.11.5.1.1.11
TDM functional read access level.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RbacAccessLevel  

genEquipSecurityAccessControlProfileEthWrite 1.3.6.1.4.1.2281.10.11.5.1.1.12
Ether functional write access level.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RbacAccessLevel  

genEquipSecurityAccessControlProfileEthRead 1.3.6.1.4.1.2281.10.11.5.1.1.13
Ether functional read access level.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RbacAccessLevel  

genEquipSecurityAccessControlProfileSyncWrite 1.3.6.1.4.1.2281.10.11.5.1.1.14
Sync functional write access level.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RbacAccessLevel  

genEquipSecurityAccessControlProfileSyncRead 1.3.6.1.4.1.2281.10.11.5.1.1.15
Sync functional read access level.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RbacAccessLevel  

genEquipSecurityAccessControlProfileRowStatus 1.3.6.1.4.1.2281.10.11.5.1.1.30
Row Status for Profile table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

genEquipSecurityAccessControlUserTable 1.3.6.1.4.1.2281.10.11.5.2
Security Access Control User Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipSecurityAccessControlUserEntry

genEquipSecurityAccessControlUserEntry 1.3.6.1.4.1.2281.10.11.5.2.1
Security Access Control User Table Entry
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipSecurityAccessControlUserEntry  

genEquipSecurityAccessControlUserName 1.3.6.1.4.1.2281.10.11.5.2.1.1
User name.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipSecurityAccessControlUserProfile 1.3.6.1.4.1.2281.10.11.5.2.1.2
User's profile name.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipSecurityAccessControlUserPassword 1.3.6.1.4.1.2281.10.11.5.2.1.3
User's password
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipSecurityAccessControlUserExpired 1.3.6.1.4.1.2281.10.11.5.2.1.4
expired date of user account.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

genEquipSecurityAccessControlUserBlock 1.3.6.1.4.1.2281.10.11.5.2.1.5
Block user account.
Status: mandatory Access: read-write
OBJECT-TYPE    
  NoYes  

genEquipSecurityAccessControlUserLastLogout 1.3.6.1.4.1.2281.10.11.5.2.1.6
Current login indication.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

genEquipSecurityAccessControlUserLoggedIn 1.3.6.1.4.1.2281.10.11.5.2.1.7
Current login indication.
Status: mandatory Access: read-write
OBJECT-TYPE    
  NoYes  

genEquipSecurityAccessControlUserRowStatus 1.3.6.1.4.1.2281.10.11.5.2.1.30
Row Status for users table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

genEquipSecurityAccessControlPassEnforceStrength 1.3.6.1.4.1.2281.10.11.5.11
Enforce strength password.
Status: mandatory Access: read-write
OBJECT-TYPE    
  NoYes  

genEquipSecurityAccessControlPassFirstLoginChange 1.3.6.1.4.1.2281.10.11.5.12
Password change for first login.
Status: mandatory Access: read-write
OBJECT-TYPE    
  NoYes  

genEquipSecurityAccessControlPassAging 1.3.6.1.4.1.2281.10.11.5.13
Password aging.
Status: mandatory Access: read-write
OBJECT-TYPE    
  NoYes  

genEquipSecurityAccessControlFailureLoginAttempt 1.3.6.1.4.1.2281.10.11.5.14
Failure login threshold blocking user account.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..10  

genEquipSecurityAccessControlBlockFailureLoginPeriod 1.3.6.1.4.1.2281.10.11.5.15
Blocking period due to failure login.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..60  

genEquipSecurityAccessControlBlockunusedAccount 1.3.6.1.4.1.2281.10.11.5.16
Period time for block unused account.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..90  

genEquipSecurityAccessControlBlockRootRemote 1.3.6.1.4.1.2281.10.11.5.17
Root remote access.
Status: mandatory Access: read-write
OBJECT-TYPE    
  NoYes  

genEquipSecurityProtocolsControl 1.3.6.1.4.1.2281.10.11.6
OBJECT IDENTIFIER    

genEquipSecurityProtocolsControlAutoSessionTimeOut 1.3.6.1.4.1.2281.10.11.6.1
Logout session after incativity timeout.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..60  

genEquipSecurityProtocolsControlSNMPAdmin 1.3.6.1.4.1.2281.10.11.6.2
SNMP Admin.
Status: mandatory Access: read-write
OBJECT-TYPE    
  EnableDisable  

genEquipSecurityProtocolsControlSNMPOperStatus 1.3.6.1.4.1.2281.10.11.6.3
SNMP Operational Status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DownUp  

genEquipSecurityProtocolsControlSNMPTrapVersion 1.3.6.1.4.1.2281.10.11.6.4
SNMP Trap version.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER v1(1), v2(2), v3(3)  

genEquipSecurityProtocolsControlSNMPMIBVersion 1.3.6.1.4.1.2281.10.11.6.5
SNMP MIB version.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipSecurityProtocolsControlSNMPV1V2Blocked 1.3.6.1.4.1.2281.10.11.6.6
SNMP V1V2 is blocked.
Status: mandatory Access: read-write
OBJECT-TYPE    
  NoYes  

genEquipSecurityProtocolsControlHTTPAdmin 1.3.6.1.4.1.2281.10.11.6.7
HTTP Admin.
Status: mandatory Access: read-write
OBJECT-TYPE    
  EnableDisable  

genEquipSecurityMonitorAndLogs 1.3.6.1.4.1.2281.10.11.7
OBJECT IDENTIFIER    

genEquipSecurityConfigLogUploadConfigTable 1.3.6.1.4.1.2281.10.11.7.1
Config Log Upload Configuration.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipSecurityConfigLogUploadConfigEntry

genEquipSecurityConfigLogUploadConfigEntry 1.3.6.1.4.1.2281.10.11.7.1.1
Config Log Upload Configuration Table Entry
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipSecurityConfigLogUploadConfigEntry  

genEquipSecurityConfigLogUploadConfigIndex 1.3.6.1.4.1.2281.10.11.7.1.1.1
Config Log Upload Configuration index. has Fixed value of 1
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipSecurityConfigLogUploadConfigProtocol 1.3.6.1.4.1.2281.10.11.7.1.1.2
Config Log Upload Configuration Protocol.
Status: mandatory Access: read-write
OBJECT-TYPE    
  FtpProtocolType  

genEquipSecurityConfigLogUploadConfigUsername 1.3.6.1.4.1.2281.10.11.7.1.1.3
Config Log Upload Username
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipSecurityConfigLogUploadConfigPassword 1.3.6.1.4.1.2281.10.11.7.1.1.4
Config Log Upload Configuration Password.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipSecurityConfigLogUploadConfigIpaddress 1.3.6.1.4.1.2281.10.11.7.1.1.5
Config Log Upload Configuration ip address (Ipv4).
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

genEquipSecurityConfigLogUploadConfigPath 1.3.6.1.4.1.2281.10.11.7.1.1.6
Config Log Upload Configuration Path.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipSecurityConfigLogUploadConfigFilename 1.3.6.1.4.1.2281.10.11.7.1.1.7
Config Log Upload Configuration Filename.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipSecurityConfigLogUploadConfigIpV6Address 1.3.6.1.4.1.2281.10.11.7.1.1.8
Config Log Upload Configuration ip address (Ipv6).
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

genEquipSecurityConfigLogUploadStatusTable 1.3.6.1.4.1.2281.10.11.7.2
Config Log Upload Status.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipSecurityConfigLogUploadStatusEntry

genEquipSecurityConfigLogUploadStatusEntry 1.3.6.1.4.1.2281.10.11.7.2.1
Config Log Upload Status Table Entry
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipSecurityConfigLogUploadStatusEntry  

genEquipSecurityConfigLogUploadStatusIndex 1.3.6.1.4.1.2281.10.11.7.2.1.1
Config Log Upload Status index. has Fixed value of 1
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipSecurityConfigLogUploadStatusStatus 1.3.6.1.4.1.2281.10.11.7.2.1.2
Config Log Upload Configuration Protocol.
Status: mandatory Access: read-write
OBJECT-TYPE    
  FileTransferStatus  

genEquipSecurityConfigLogUploadStatusPrcntg 1.3.6.1.4.1.2281.10.11.7.2.1.3
Progress status in percentage.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipSecurityConfigLogUpload 1.3.6.1.4.1.2281.10.11.7.10
Configuration Log Upload.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(0), upload-security-log(1)  

genEquipSecurityRadiusServer 1.3.6.1.4.1.2281.10.11.8
OBJECT IDENTIFIER    

genEquipSecurityRadiusServerConfigurationTable 1.3.6.1.4.1.2281.10.11.8.1
Radius configuration table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipSecurityRadiusServerConfigurationEntry

genEquipSecurityRadiusServerConfigurationEntry 1.3.6.1.4.1.2281.10.11.8.1.1
Radius configuration table Entry
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipSecurityRadiusServerConfigurationEntry  

genEquipSecurityAccessControlRadiusServerId 1.3.6.1.4.1.2281.10.11.8.1.1.1
Server id: 1 - primary, 2-secondary
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipSecurityAccessControlRadiusServerIpV4Address 1.3.6.1.4.1.2281.10.11.8.1.1.2
The IP address of the RADIUS Server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

genEquipSecurityAccessControlRadiusServerIpv6Address 1.3.6.1.4.1.2281.10.11.8.1.1.3
The IP address of the RADIUS Server
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

genEquipSecurityAccessControlRadiusServerPort 1.3.6.1.4.1.2281.10.11.8.1.1.4
The port ID of the RADIUS protocol in the RADIUS Server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

genEquipSecurityAccessControlRadiusServerRetries 1.3.6.1.4.1.2281.10.11.8.1.1.5
The number of times the agent will retry to communicate with the selected RADIUS server before declaring the server to be not reachable.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

genEquipSecurityAccessControlRadiusServerTimeout 1.3.6.1.4.1.2281.10.11.8.1.1.6
The timeout that the agent will wait in each communication with the selected RADIUS server before retrying if no response is received.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

genEquipSecurityAccessControlRadiusServerSharedSecret 1.3.6.1.4.1.2281.10.11.8.1.1.7
The shared secret of the Radius Server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

genEquipSecurityAccessControlRadiusServerConnectivityStatus 1.3.6.1.4.1.2281.10.11.8.1.1.8
The connectivity status of the RADIUS server in the last login tried.
Status: mandatory Access: read-only
OBJECT-TYPE    
  EnableDisable  

genEquipSecurityAccessControlRadiusUsersTable 1.3.6.1.4.1.2281.10.11.8.2
Radius privilege table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipSecurityAccessControlRadiusUsersEntry

genEquipSecurityAccessControlRadiusUsersEntry 1.3.6.1.4.1.2281.10.11.8.2.1
Radius privilege table Entry
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipSecurityAccessControlRadiusUsersEntry  

genEquipSecurityAccessControlRadiusUsersId 1.3.6.1.4.1.2281.10.11.8.2.1.1
User ID
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipSecurityAccessControlRadiusUserInstances 1.3.6.1.4.1.2281.10.11.8.2.1.2
A number of the same connected users.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipSecurityAccessControlRadiusUsersAccessChannels 1.3.6.1.4.1.2281.10.11.8.2.1.3
A bits stands for each access channel: serial-0, telnet-1, ssh-2, web-3
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipSecurityAccessControlRadiusUsersEthReadLevel 1.3.6.1.4.1.2281.10.11.8.2.1.4
The RADIUS permitted access for Ethernet Read Level functional group.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RaduisAcceaaLevel  

genEquipSecurityAccessControlRadiusUsersEthWriteLevel 1.3.6.1.4.1.2281.10.11.8.2.1.5
The RADIUS permitted access for Ethernet Write Level functional group.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RaduisAcceaaLevel  

genEquipSecurityAccessControlRadiusUsersMngReadLevel 1.3.6.1.4.1.2281.10.11.8.2.1.6
The RADIUS permitted access for MNG Read Level functional group.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RaduisAcceaaLevel  

genEquipSecurityAccessControlRadiusUsersMngWriteLevel 1.3.6.1.4.1.2281.10.11.8.2.1.7
The RADIUS permitted access for MNG Write Level functional group.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RaduisAcceaaLevel  

genEquipSecurityAccessControlRadiusUsersRadioReadLevel 1.3.6.1.4.1.2281.10.11.8.2.1.8
The RADIUS permitted access for Radio Read Level functional group.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RaduisAcceaaLevel  

genEquipSecurityAccessControlRadiusUsersRadioWriteLevel 1.3.6.1.4.1.2281.10.11.8.2.1.9
The RADIUS permitted access for Radio Write Level functional group.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RaduisAcceaaLevel  

genEquipSecurityAccessControlRadiusUsersSecurityReadLevel 1.3.6.1.4.1.2281.10.11.8.2.1.10
The RADIUS permitted access for Security Read Level functional group.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RaduisAcceaaLevel  

genEquipSecurityAccessControlRadiusUsersSecurityWriteLevel 1.3.6.1.4.1.2281.10.11.8.2.1.11
The RADIUS permitted access for Security Write Level functional group.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RaduisAcceaaLevel  

genEquipSecurityAccessControlRadiusUsersSyncReadLevel 1.3.6.1.4.1.2281.10.11.8.2.1.12
The RADIUS permitted access for Sync Read Level functional group.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RaduisAcceaaLevel  

genEquipSecurityAccessControlRadiusUsersSyncWriteLevel 1.3.6.1.4.1.2281.10.11.8.2.1.13
The RADIUS permitted access for Sync Write Level functional group.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RaduisAcceaaLevel  

genEquipSecurityAccessControlRadiusUsersTdmReadLevel 1.3.6.1.4.1.2281.10.11.8.2.1.14
The RADIUS permitted access for TDM Read Level functional group.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RaduisAcceaaLevel  

genEquipSecurityAccessControlRadiusUsersTdmWriteLevel 1.3.6.1.4.1.2281.10.11.8.2.1.15
The RADIUS permitted access for TDM Write Level functional group.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RaduisAcceaaLevel  

genEquipSecurityRadiusAdmin 1.3.6.1.4.1.2281.10.11.8.10
Control working withRadius Server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  EnableDisable  

genEquipSecurityCertificate 1.3.6.1.4.1.2281.10.11.9
OBJECT IDENTIFIER    

genEquipSecurityCsrCertificateFileTransferSet 1.3.6.1.4.1.2281.10.11.9.1
CSR generate and Upload.
Status: mandatory Access: read-write
OBJECT-TYPE    
  CsrCertificateFTState  

genEquipSecurityCsrStatus 1.3.6.1.4.1.2281.10.11.9.2
Status of last geneate and upload.
Status: mandatory Access: read-only
OBJECT-TYPE    
  FTStatus  

genEquipSecurityCsrCertificateGenerateAndUploadPercentage 1.3.6.1.4.1.2281.10.11.9.3
Percentage of last generate CSR and upload.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipSecurityCertificateInstallSet 1.3.6.1.4.1.2281.10.11.9.4
Certificate Install.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OffOn  

genEquipSecurityCertificateDownloadStatus 1.3.6.1.4.1.2281.10.11.9.5
tatus of last certificate download.
Status: mandatory Access: read-only
OBJECT-TYPE    
  FTStatus  

genEquipSecurityCertificateDownloadPercentage 1.3.6.1.4.1.2281.10.11.9.6
Percentage of certificate download operation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipSecurityCsrAttributesTable 1.3.6.1.4.1.2281.10.11.9.10
CSR Attributes Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipSecurityCsrAttributesEntry

genEquipSecurityCsrAttributesEntry 1.3.6.1.4.1.2281.10.11.9.10.1
CSR Attributes Table Entry
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipSecurityCsrAttributesEntry  

genEquipSecurityCsrAttributesIndex 1.3.6.1.4.1.2281.10.11.9.10.1.1
Index to table, constant 1
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipSecurityCsrAttributesCountry 1.3.6.1.4.1.2281.10.11.9.10.1.2
The two-letter ISO abbreviation for your country (ISO3166-1) (example US).
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipSecurityCsrAttributesLocality 1.3.6.1.4.1.2281.10.11.9.10.1.3
The city where your organization is legally located
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipSecurityCsrAttributesState 1.3.6.1.4.1.2281.10.11.9.10.1.4
The state or province where your organization is legally located. Can not be abbreviated.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipSecurityCsrAttributesOrganization 1.3.6.1.4.1.2281.10.11.9.10.1.5
The exact legal name of your organization. Do not abbreviate your organization name.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipSecurityCsrAttributesOu 1.3.6.1.4.1.2281.10.11.9.10.1.6
Section of the organization. Example: Marketing.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipSecurityCsrAttributesCommonName 1.3.6.1.4.1.2281.10.11.9.10.1.7
The fully qualified domain name for your web server. This must be an exact match.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipSecurityCsrAttributesEmail 1.3.6.1.4.1.2281.10.11.9.10.1.8
An email address used to contact your organization.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipSecurityCsrAttributesFileFormat 1.3.6.1.4.1.2281.10.11.9.10.1.9
CSR file format. PEM or DER.
Status: mandatory Access: read-only
OBJECT-TYPE    
  CsrFileFormat  

genEquipSecurityCsrUploadConfigTable 1.3.6.1.4.1.2281.10.11.9.11
CSR (Certificate Request) Upload Configuration Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipSecurityCsrUploadConfigEntry

genEquipSecurityCsrUploadConfigEntry 1.3.6.1.4.1.2281.10.11.9.11.1
CSR (Certificate Request) Upload Configuration Table Entry
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipSecurityCsrUploadConfigEntry  

genEquipSecurityCsrUploadConfigIndex 1.3.6.1.4.1.2281.10.11.9.11.1.1
CSR upload Configuration index. has Fixed value of 1
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipSecurityCsrUploadConfigIpv4Address 1.3.6.1.4.1.2281.10.11.9.11.1.2
IPv4 address of the server, where the file are to be transferred to/from.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

genEquipSecurityCsrUploadConfigIpV6Address 1.3.6.1.4.1.2281.10.11.9.11.1.3
IPv6 address of the server, where the file are to be transferred to/from
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

genEquipSecurityCsrUploadConfigTableUsername 1.3.6.1.4.1.2281.10.11.9.11.1.4
User name for accesssing files in the server (User credentials to access server).
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipSecurityCsrUploadConfigPassword 1.3.6.1.4.1.2281.10.11.9.11.1.5
Password (User credentials to access server).
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipSecurityCsrUploadConfigPath 1.3.6.1.4.1.2281.10.11.9.11.1.6
Location of file in the server (folder).
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipSecurityCsrUploadConfigFilename 1.3.6.1.4.1.2281.10.11.9.11.1.7
Filename in the server, where the file are to be transferred to/from.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

genEquipSecurityCertificateDownloadConfigTable 1.3.6.1.4.1.2281.10.11.9.12
CSR (Certificate Request) Download Configuration Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GenEquipSecurityCertificateDownloadConfigEntry

genEquipSecurityCertificateDownloadConfigEntry 1.3.6.1.4.1.2281.10.11.9.12.1
CSR (Certificate Request) Download Configuration Table Entry
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  GenEquipSecurityCertificateDownloadConfigEntry  

genEquipSecurityCertificateDownloadConfigIndex 1.3.6.1.4.1.2281.10.11.9.12.1.1
Certificate download configuration index. has Fixed value of 1
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

genEquipSecurityCertificateDownloadConfigIpv4Address 1.3.6.1.4.1.2281.10.11.9.12.1.2
IPv4 address of the server, where the file are to be transferred to/from.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

genEquipSecurityCertificateDownloadConfigIpV6Address 1.3.6.1.4.1.2281.10.11.9.12.1.3
IPv6 address of the server, where the file are to be transferred to/from
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

genEquipSecurityCertificateDownloadConfigUsername 1.3.6.1.4.1.2281.10.11.9.12.1.4
User name for accesssing files in the server (User credentials to access server).
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipSecurityCertificateDownloadConfigPassword 1.3.6.1.4.1.2281.10.11.9.12.1.5
Password (User credentials to access server).
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipSecurityCertificateDownloadConfigPath 1.3.6.1.4.1.2281.10.11.9.12.1.6
Location of file in the server (folder).
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

genEquipSecurityCertificateDownloadConfigFilename 1.3.6.1.4.1.2281.10.11.9.12.1.7
Filename in the server, where the file are to be transferred to/from.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString