MPLS-LSR-EXT-STD-MIB
File:
MPLS-LSR-EXT-STD-MIB.mib (7804 bytes)
Imported modules
Imported symbols
Defined Types
MplsXCExtEntry |
|
SEQUENCE |
|
|
|
|
mplsXCExtTunnelPointer |
RowPointer |
|
|
mplsXCExtOppositeDirXCPtr |
RowPointer |
|
Defined Values
mplsLsrExtStdMIB |
1.3.6.1.2.1.10.166.19 |
This MIB module contains generic object definitions for
MPLS LSRs in transport networks.
Copyright (c) 2015 IETF Trust and the persons identified as
authors of the code. All rights reserved.
Redistribution and use in source and binary forms, with or
without modification, is permitted pursuant to, and subject to
the license terms contained in, the Simplified BSD License set
forth in Section 4.c of the IETF Trust's Legal Provisions
Relating to IETF Documents
(http://trustee.ietf.org/license-info). |
MODULE-IDENTITY |
|
|
|
mplsXCExtTable |
1.3.6.1.2.1.10.166.19.1.1 |
This table sparse augments the mplsXCTable of
MPLS-LSR-STD-MIB (RFC 3813) to provide MPLS-TP-specific
information about associated tunnel information |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
MplsXCExtEntry |
|
mplsXCExtEntry |
1.3.6.1.2.1.10.166.19.1.1.1 |
An entry in this table sparsely extends the cross-connect
information represented by an entry in
the mplsXCTable in MPLS-LSR-STD-MIB (RFC 3813) through
a sparse augmentation. An entry can be created by
a network operator via SNMP SET commands or in
response to signaling protocol events. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
MplsXCExtEntry |
|
|
mplsXCExtTunnelPointer |
1.3.6.1.2.1.10.166.19.1.1.1.1 |
This read-only object indicates the back pointer to
the tunnel entry segment.
The only valid value for Tunnel Pointer is
mplsTunnelTable entry. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
RowPointer |
|
|
mplsXCExtOppositeDirXCPtr |
1.3.6.1.2.1.10.166.19.1.1.1.2 |
This object indicates the pointer to the opposite-
direction XC entry. This object cannot be modified if
mplsXCRowStatus for the corresponding entry in the
mplsXCTable is active(1). If this pointer is not set or
removed, mplsXCOperStatus should be set to down(2). |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
RowPointer |
|
|
mplsLsrExtModuleFullCompliance |
1.3.6.1.2.1.10.166.19.2.1.1 |
Compliance statement for agents that provide full support
for MPLS-LSR-EXT-STD-MIB.
The mandatory group has to be implemented by all LSRs
that originate, terminate, or act as transit for
TE-LSPs/tunnels.
In addition, depending on the type of tunnels supported,
other groups become mandatory as explained below. |
Status: current |
Access: read-create |
MODULE-COMPLIANCE |
|
|
|
mplsLsrExtModuleReadOnlyCompliance |
1.3.6.1.2.1.10.166.19.2.1.2 |
Compliance requirement for implementations that only
provide read-only support for MPLS-LSR-EXT-STD-MIB.
Such devices can then be monitored but cannot be
configured using this MIB module. |
Status: current |
Access: read-only |
MODULE-COMPLIANCE |
|
|
|
mplsXCExtGroup |
1.3.6.1.2.1.10.166.19.2.2.1 |
This object should be supported in order to access
the tunnel entry from the XC entry. |
Status: current |
Access: read-only |
OBJECT-GROUP |
|
|
|
mplsXCExtReadOnlyObjectsGroup |
1.3.6.1.2.1.10.166.19.2.2.2 |
This Object is needed to associate the opposite-direction
(forward/reverse) XC entry. |
Status: current |
Access: read-only |
OBJECT-GROUP |
|
|
|