MLD-SNOOPING-MIB

File: MLD-SNOOPING-MIB.mib (25863 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC RFC1213-MIB
SNMP-FRAMEWORK-MIB DLINK-ID-REC-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE IpAddress
Unsigned32 MacAddress RowStatus
DisplayString SnmpAdminString dlink-common-mgmt

Defined Types

Ipv6Address  
This data type is used to model IPv6 addresses. This is a binary string of 16 octets in network byte-order.
TEXTUAL-CONVENTION    
  OCTET STRING Size(16)  

PortList  
OCTET STRING Size(0..127)    

SwMldSnoopingCtrlEntry  
SEQUENCE    
  swMldSnoopingCtrlVid INTEGER
  swMldSnoopingQueryInterval INTEGER
  swMldSnoopingMaxResponseTime INTEGER
  swMldSnoopingRobustness INTEGER
  swMldSnoopingLastMemberQueryInterval INTEGER
  swMldSnoopingHostTimeout INTEGER
  swMldSnoopingRouteTimeout INTEGER
  swMldSnoopingDoneTimer INTEGER
  swMldSnoopingQueryState INTEGER
  swMldSnoopingCurrentState INTEGER
  swMldSnoopingCtrlState INTEGER
  swMldSnoopingFastDoneState INTEGER
  swMldSnoopingVersion INTEGER

SwMldSnoopingGroupInfoEntry  
SEQUENCE    
  swMldSnoopingGroupInfoVid INTEGER
  swMldSnoopingGroupInfoIpAddr Ipv6Address
  swMldSnoopingGroupInfoMacAddr MacAddress
  swMldSnoopingGroupInfoPortMap PortList
  swMldSnoopingGroupInfoReportCount INTEGER

SwMldSnpRouterPortsEntry  
SEQUENCE    
  swMldSnpRouterPortsVid INTEGER
  swMldSnpRouterStaticPortList PortList
  swMldSnpRouterDynamicPortList PortList
  swMldSnpRouterForbiddenPortList PortList

SwMldSnoopingGroupEntry  
SEQUENCE    
  swMldSnoopingGroupVid INTEGER
  swMldSnoopingGroupGroupAddr Ipv6Address
  swMldSnoopingGroupSourceAddr Ipv6Address
  swMldSnoopingGroupIncludePortMap PortList
  swMldSnoopingGroupExcludePortMap PortList

SwMldSnpForwardingEntry  
SEQUENCE    
  swMldSnpVid INTEGER
  swMldSnpSourceIpAddr Ipv6Address
  swMldSnpMutiGroupIpAddr Ipv6Address
  swMldSnpForwardingListenPort PortList

Defined Values

swMldSnpMIB 1.3.6.1.4.1.171.12.34
The Structure of MLD snooping management for the proprietary enterprise.
MODULE-IDENTITY    

swMldSnpCtrl 1.3.6.1.4.1.171.12.34.1
OBJECT IDENTIFIER    

swMldSnpInfo 1.3.6.1.4.1.171.12.34.2
OBJECT IDENTIFIER    

swMldSnpMgmt 1.3.6.1.4.1.171.12.34.3
OBJECT IDENTIFIER    

swMldSnoopingGlobalState 1.3.6.1.4.1.171.12.34.1.1
This object indicates if the MLD snooping capture function is enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swMldSnoopingMcstRTOnly 1.3.6.1.4.1.171.12.34.1.2
Specifies that the switch should forward all multicast traffic to a multicast-enabled IPv6 router only.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swMldSnoopingMaxSupportedVlans 1.3.6.1.4.1.171.12.34.3.1
Maximum number of VLANs in the MLD snooping table (swMldSnoopingCtrlTable).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swMldSnoopingCtrlTable 1.3.6.1.4.1.171.12.34.3.2
The table controls the VLAN's MLD function. Its scale depends on the current VLAN state (swL2VlanInfoStatus). If the VLAN is in disabled mode, there is only one entry in the table, with index 1. If the VLAN is in Port-Base or 802.1q mode, the number of entries can be up to 12, with an index range from 1 to 12.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwMldSnoopingCtrlEntry

swMldSnoopingCtrlEntry 1.3.6.1.4.1.171.12.34.3.2.1
The entry in MLD control table (swMldSnoopingCtrlTable). The entry is effective only when MLD capture switch (swMldSnoopingGlobalState) is enabled.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwMldSnoopingCtrlEntry  

swMldSnoopingCtrlVid 1.3.6.1.4.1.171.12.34.3.2.1.1
This object indicates the MLD control entry's VLAN ID. If the VLAN is disabled, the VID is always 0 and cannot be changed by management users. If VLAN is in Port-Base mode, the VID is arranged from 1 to 12, fixed form. If VLAN is in 802.1q mode, the VID setting can vary from 1 to 4094 by the management user, and the VID in each entry must be unique in the MLD Control Table.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swMldSnoopingQueryInterval 1.3.6.1.4.1.171.12.34.3.2.1.2
The frequency at which MLD Host-Query packets are transmitted on this switch.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

swMldSnoopingMaxResponseTime 1.3.6.1.4.1.171.12.34.3.2.1.3
The maximum query response time on this switch.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..25  

swMldSnoopingRobustness 1.3.6.1.4.1.171.12.34.3.2.1.4
The Robustness Variable allows tuning for the expected packet loss on a subnet. If a subnet is expected to have a high loss, the Robustness Variable may be increased. MLD is robust to (Robustness Variable-1) packet losses.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..255  

swMldSnoopingLastMemberQueryInterval 1.3.6.1.4.1.171.12.34.3.2.1.5
The Last Member Query Interval is the Max Response Time inserted into Group-Specific Queries sent in response to Leave Group messages and is also the amount of time between Group-Specific Query messages.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..25  

swMldSnoopingHostTimeout 1.3.6.1.4.1.171.12.34.3.2.1.6
The timer value for sending a MLD query packet when none were sent by the host in the LAN. The timer works on a per-VLAN basis. Our device will be activated to send a query message if the timer has expired.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..16711450  

swMldSnoopingRouteTimeout 1.3.6.1.4.1.171.12.34.3.2.1.7
The Router Timeout is how long a host must wait after hearing a Query before it sends any MLD messages.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..16711450  

swMldSnoopingDoneTimer 1.3.6.1.4.1.171.12.34.3.2.1.8
When a querier receives a Leave Group message for a group that has group members on the reception interface, it sends Group-Specific Queries swMldSnoopingDoneTimer to the group that is left.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..16711450  

swMldSnoopingQueryState 1.3.6.1.4.1.171.12.34.3.2.1.9
This object decides if the MLD query is enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swMldSnoopingCurrentState 1.3.6.1.4.1.171.12.34.3.2.1.10
This object indicates the current MLD query state.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), querier(2), non-querier(3)  

swMldSnoopingCtrlState 1.3.6.1.4.1.171.12.34.3.2.1.11
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different for each of the following values. disable(2) - MLD function is disabled for this entry. enable(3) - MLD function is enabled for this entry.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disable(2), enable(3)  

swMldSnoopingFastDoneState 1.3.6.1.4.1.171.12.34.3.2.1.12
This object indicates the fast_leave status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different for each of the following values. disable(2) - MLD fast-done function is disabled for this entry. enable(3) - MLD fast-done function is enabled for this entry.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disable(2), enable(3)  

swMldSnoopingVersion 1.3.6.1.4.1.171.12.34.3.2.1.13
This object indicates the MLD version of this entry. If the MLD version is configured with a lower version, the higher version's MLD Report/Leave messages will be ignored.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER version-1(1), version-2(2)  

swMldSnoopingGroupInfoTable 1.3.6.1.4.1.171.12.34.3.3
The table contains the current MLD snooping information captured by this device, provided that swMldSnoopingGlobalState and swMldSnoopingCtrlState of associated VLAN entries are all enabled. Note that the priority of MLD table entries is lower than the Filtering Table, i.e. if there is a table hash collision between the entries of the MLD Table and the Filtering Table inside the switch H/W address table, then the Filtering Table entry overwrites the colliding entry of the MLD snooping Table.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwMldSnoopingGroupInfoEntry

swMldSnoopingGroupInfoEntry 1.3.6.1.4.1.171.12.34.3.3.1
Information about current MLD information which has been captured by this device, provided that swMldSnoopingGlobalState and swMldSnoopingCtrlState of the associated VLAN entries are all enabled.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SwMldSnoopingGroupInfoEntry  

swMldSnoopingGroupInfoVid 1.3.6.1.4.1.171.12.34.3.3.1.1
This object indicates the VID of an individual MLD table entry. It shows the VID of MLD report information that has been captured on the network.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swMldSnoopingGroupInfoIpAddr 1.3.6.1.4.1.171.12.34.3.3.1.2
This object identifies the group IP address which is captured from the MLD packet, on a per-VLAN basis.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Ipv6Address  

swMldSnoopingGroupInfoMacAddr 1.3.6.1.4.1.171.12.34.3.3.1.3
This object identifies the MAC addresses that correspond to swMldSnoopingGroupInfoIpAddr, on a per-VLAN basis.
Status: obsolete Access: read-only
OBJECT-TYPE    
  MacAddress  

swMldSnoopingGroupInfoPortMap 1.3.6.1.4.1.171.12.34.3.3.1.4
This object indicates which ports belong to the same multicast group, on a per-VLAN basis. Each multicast group has an octet string to indicate the port map. The most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'(Note that the setting of the bit corresponding to the port from which a frame is received is irrelevant). The 4 octets represent one unit port according to its logical port. If the unit has less than 32 ports, other ports will be set to 0.
Status: obsolete Access: read-only
OBJECT-TYPE    
  PortList  

swMldSnoopingGroupInfoReportCount 1.3.6.1.4.1.171.12.34.3.3.1.5
This object indicates how many report packets were received by our device corresponding with the entry when the MLD function is enabled, on a per-VLAN basis.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swMldSnpRouterPortsTable 1.3.6.1.4.1.171.12.34.3.4
This table controls the VLAN's MLD router ports function.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwMldSnpRouterPortsEntry

swMldSnpRouterPortsEntry 1.3.6.1.4.1.171.12.34.3.4.1
This entry shows the MLD router ports table (swMldSnoopingCtrlTable).
Status: current Access: not-accessible
OBJECT-TYPE    
  SwMldSnpRouterPortsEntry  

swMldSnpRouterPortsVid 1.3.6.1.4.1.171.12.34.3.4.1.1
This object indicates the MLD router ports entry VLAN ID. If a VLAN is disabled, the VID is always 0 and cannot be changed by management users. If a VLAN is in Port-Base mode, the VID is arranged from 1 to 12, fixed form. If a VLAN is in 802.1q mode, the VID setting can vary from 1 to 4094 by a management user, and the VID in each entry must be unique in the MLD ports Table.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swMldSnpRouterStaticPortList 1.3.6.1.4.1.171.12.34.3.4.1.2
Displays router ports that have been statically configured.
Status: current Access: read-write
OBJECT-TYPE    
  PortList  

swMldSnpRouterDynamicPortList 1.3.6.1.4.1.171.12.34.3.4.1.3
Displays router ports that have been dynamically configured.
Status: current Access: read-only
OBJECT-TYPE    
  PortList  

swMldSnpRouterForbiddenPortList 1.3.6.1.4.1.171.12.34.3.4.1.4
Displays router ports that have been configured to be forbidden.
Status: current Access: read-write
OBJECT-TYPE    
  PortList  

swMldSnoopingGroupTable 1.3.6.1.4.1.171.12.34.3.5
The table contains the current MLD snooping information captured by the device, provided that the swMldSnoopingGlobalState and swMldSnoopingCtrlState of the associated VLAN entries are all enabled. Note that the priority of the MLD table entries is lower than the Filtering Table, i.e. if there is a table hash collision between the entries of the MLD Table and the Filtering Table inside the switch H/W address table, then the Filtering Table entry overwrites the colliding entry of the MLD snooping Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwMldSnoopingGroupEntry

swMldSnoopingGroupEntry 1.3.6.1.4.1.171.12.34.3.5.1
Information about the current MLD information which has been captured by the device, provided that swMldSnoopingGlobalState and swMldSnoopingCtrlState of the associated VLAN entries are all enabled.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwMldSnoopingGroupEntry  

swMldSnoopingGroupVid 1.3.6.1.4.1.171.12.34.3.5.1.1
This object indicates the VID of the individual MLD table entry. It shows the VID of the MLD report information captured on the network.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swMldSnoopingGroupGroupAddr 1.3.6.1.4.1.171.12.34.3.5.1.2
This object identifies the group IP address which has been captured from the MLD packet, on a per-VLAN basis.
Status: current Access: read-only
OBJECT-TYPE    
  Ipv6Address  

swMldSnoopingGroupSourceAddr 1.3.6.1.4.1.171.12.34.3.5.1.3
This object identifies the source addresses which correspond to swMldSnoopingGroupInfoGroupAddr, on a per-VLAN basis.
Status: current Access: read-only
OBJECT-TYPE    
  Ipv6Address  

swMldSnoopingGroupIncludePortMap 1.3.6.1.4.1.171.12.34.3.5.1.4
This object indicates the port list under INCLUDE mode.
Status: current Access: read-only
OBJECT-TYPE    
  PortList  

swMldSnoopingGroupExcludePortMap 1.3.6.1.4.1.171.12.34.3.5.1.5
This object indicates the port list under EXCLUDE mode.
Status: current Access: read-only
OBJECT-TYPE    
  PortList  

swMldSnpForwardingTable 1.3.6.1.4.1.171.12.34.3.6
This table contains the MLD Snooping forwarding information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwMldSnpForwardingEntry

swMldSnpForwardingEntry 1.3.6.1.4.1.171.12.34.3.6.1
A list of information about MLD Snooping forwarding.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwMldSnpForwardingEntry  

swMldSnpVid 1.3.6.1.4.1.171.12.34.3.6.1.1
This object indicates the MLD Forwarding entry's VLAN ID.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swMldSnpSourceIpAddr 1.3.6.1.4.1.171.12.34.3.6.1.2
This object identifies the forwarding IP address, which is captured from the MLD packet.
Status: current Access: read-only
OBJECT-TYPE    
  Ipv6Address  

swMldSnpMutiGroupIpAddr 1.3.6.1.4.1.171.12.34.3.6.1.3
This object identifies the Multicast Group IP address, which is captured from MLD packet.
Status: current Access: read-only
OBJECT-TYPE    
  Ipv6Address  

swMldSnpForwardingListenPort 1.3.6.1.4.1.171.12.34.3.6.1.4
Indicates the MLD Snooping forwarding listen port.
Status: current Access: read-only
OBJECT-TYPE    
  PortList