prtOutputEntry |
1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1 |
OBJECT IDENTIFIER |
|
|
|
prtoutputremainingcapacity |
1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1.5 |
The remaining capacity of the possible output sub-unit
capacity in output sub-unit capacity units (PrtCapacityUnitTC)
of this output sub-unit. If this output sub-unit can
reliably sense this value, the value is sensed by the
printer and may not be modified by management requests;
otherwise, the value may be written (by
a Remote Control Panel or a Management
Application). The value (-1) means other and
specifically indicates that the sub-unit places no
restrictions on this parameter. The value (-2) means
unknown. The value (-3) means that the printer knows that
there remains capacity for at least one unit.
Refer to ftp://ftp.pwg.org/pub/pwg/pmp/drafts/pmib_031698.txt, for more details in the Standard Printer MIB.
Additional information:
Replaces PML NOT-READY-OUTBIN-FULL and
STATUS-OUTBIN-FULL.
The values reported for output sub-unit 1 (face-down,
top bin) will be either (-3) if it is not
full or (0) if it is full.
Output sub-unit 2 (face-up, left side bin) does not
have any sensing, so it will always report unknown (-2).
The first output sub-unit (3) of the MBM reports
either (-3) if it is not full or (0) if
it is full.
In mailbox mode, the MBM sub-units (4-8) will report
(250) when empty, (125) when there's room for <250
sheets and (0) when full.
The STAPLER sub-unit (9) will report (-3) when not full
and (0) when full.
Note: Due to MBM mechanism limitations, the value
reported may not always be accurate (the bin status is
detected only when the media delivery head is moved to
or past a physical bin). Also, for stacker mode a bin
is considered full as long as any bin above it is not
empty.
Default values assume all sub-units are empty and the
MBM is in mailbox mode. |
Status: optional |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
prtoutputpagedeliveryorientation |
1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1.20 |
The reading surface that will be `up' when pages are
delivered to the associated output sub-unit. Values are
faceUp and faceDown. (Note: interpretation of these
values is in general context-dependent based on locale;
presentation of these values to an end-user should be
normalized to the expectations of the user).
Refer to ftp://ftp.pwg.org/pub/pwg/pmp/drafts/pmib_031698.txt, for more details in the Standard Printer MIB. |
Status: optional |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
ePfaceUp(3), ePfaceDown(4) |
|
prtoutputpagecollated |
1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1.23 |
This object indicates that the output sub-unit
supports page collation, and if so, whether the feature is
enabled. See glossary for definition of how this document defines
collation.
Refer to ftp://ftp.pwg.org/pub/pwg/pmp/drafts/pmib_031698.txt, for more details in the Standard Printer MIB.
Additional information:
Page collation is not supported. |
Status: optional |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
ePother(1), ePon(3), ePoff(4), ePnotPresent(5) |
|