Lannet-Trapsv2-MIB

File: Lannet-Trapsv2-MIB.mib (75504 bytes)

Imported modules

APPLIC-MIB CONFIG-MIB DS1-MIB
GEN-MIB IF-MIB POLICY-MIB
RFC1213-MIB RMON-MIB SNMPv2-CONF
SNMPv2-MIB SNMPv2-SMI XSWITCH-MIB

Imported symbols

lseIntPortCAMLastChange vnsPacketMACAddress vnsPacketIPAddress
vnsPacketIPNetMask vnsPacketExpectedVLAN vnsPacketDetectedVLAN
vnsPacketBoxAgentIP vnsPacketExpectedIfName vnsPacketDetectedIfName
chLntAgIntTemp chHWIntTempWarning chHWIntTempThresh
genGroupId genGroupMPSActivityStatus genGroupBUPSActivityStatus
genGroupFaultMask genGroupCascadUpStatus genGroupCascadDownStatus
genPortGroupId genPortId genPortFaultMask
genPortFunctionalStatus softRedundancyName softRedundancyGroupId1
softRedundancyPortId1 softRedundancyGroupId2 softRedundancyPortId2
softRedundancyStatus dsx1LineStatus lannet
ifName ifAlias ipPolicyListID
ipPolicyRuleListID ipPolicyRuleID ipPolicyRuleDescription
ipPolicyControlSlot ipPolicyAccessControlViolationEntID ipPolicyAccessControlViolationSrcAddr
ipPolicyAccessControlViolationDstAddr ipPolicyAccessControlViolationProtocol ipPolicyAccessControlViolationL4SrcPort
ipPolicyAccessControlViolationL4DstPort ipPolicyAccessControlViolationEstablished ipPolicyAccessControlViolationIfIndex
ipPolicyAccessControlViolationSubCtxt ipPolicyAccessControlViolationTime ipPolicyAccessControlViolationRuleType
ipPolicyActivationEntID ipPolicyActivationifIndex ipPolicyActivationSubContext
ipPolicyActivationList ifIndex ifAdminStatus
ifOperStatus ipNetToMediaPhysAddress ipNetToMediaNetAddress
DisplayString rmonNotificationGroup OBJECT-GROUP
AGENT-CAPABILITIES NOTIFICATION-GROUP coldStart
warmStart authenticationFailure IpAddress
OBJECT-TYPE MODULE-IDENTITY OBJECT-IDENTITY
NOTIFICATION-TYPE scGenGroupBUPSFansStatus scGenGroupFansStatus
scGenPortGroupId scGenPortId scGenPortLastIntruderSourceAddr
scGenLinkAggregationId scGenLinkAggregationName scGenLinkAggregationFunctionalStatus
scGenLinkAggregationAutoNegResults scGenLinkAggregationFaultMask scGenLinkAggregationStatus
scEthPortGroupId scEthPortId scEthPortFunctionalStatus
scGenPortDot1xMAC scGenGroupDot1xSystemMaxNumSupplicant scGenSwitchDot1xPortMaxSuppNum

Defined Values

lntTraps 3.1.81.38
SMIv2 definition of p330/P130 traps
MODULE-IDENTITY    

lntConfigChangeEvents 3.1.81.38.1
Groups together all configuration change related events
Status: current Access: read-write
OBJECT-IDENTITY    

lntConfigChangePrefix 3.1.81.38.1.0
The next to last sub- identifier in the name of any newly-defined notification must have the value zero
Status: current Access: read-write
OBJECT-IDENTITY    

lntConfigChangeEvent 3.1.81.38.1.0.1
Notification generated in case of configuration change. List of events triggering notitication is TBD
Status: current Access: read-write
NOTIFICATION-TYPE    

lntStackMasterReelection 3.1.81.38.1.0.82
The trap should be triggered in an event that an election process leads to selection of a different module as a Stack Master
Status: current Access: read-write
NOTIFICATION-TYPE    

lntSWRedundancyEvents 3.1.81.38.2
Groups together all software redundancy related events
Status: current Access: read-write
OBJECT-IDENTITY    

lntSWRedundancyPrefix 3.1.81.38.2.0
The next to last sub- identifier in the name of any newly-defined notification must have the value zero
Status: current Access: read-write
OBJECT-IDENTITY    

lntSoftRedDelEvent 3.1.81.38.2.0.12
The trap notifies the manager of the deletion of the specified redundant link, which is identified by the softRedundancyId.
Status: current Access: read-write
NOTIFICATION-TYPE    

lntSoftRedNewEvent 3.1.81.38.2.0.13
The trap is generated on the creation of the redundant links for the specified ports. It gives the logical name of the redundant link the identification of the main and secondary ports and the status of the link. The softRedundancyId defines the instances of the above- mentioned variables.
Status: current Access: read-write
NOTIFICATION-TYPE    

lntTempratureEvents 3.1.81.38.3
Groups together all temprature related events
Status: current Access: read-write
OBJECT-IDENTITY    

lntTempratureWarningPrefix 3.1.81.38.3.0
The next to last sub- identifier in the name of any newly-defined notification must have the value zero
Status: current Access: read-write
OBJECT-IDENTITY    

lntTempratureWarning 3.1.81.38.3.0.14
This trap notifies the management station of the internal board/enclosure temperature fluctuations. It is generated when the temperature exceeds the threshold chHWIntTempThresh.
Status: current Access: read-write
NOTIFICATION-TYPE    

lntTempratureOk 3.1.81.38.3.0.23
This trap notifies the management station that the internal board/enclosure temperature fluctuations situation is back to normal.
Status: current Access: read-write
NOTIFICATION-TYPE    

lntCAMChangeEvents 3.1.81.38.4
Groups together all CAM related events
Status: current Access: read-write
OBJECT-IDENTITY    

lntCAMChangePrefix 3.1.81.38.4.0
The next to last sub- identifier in the name of any newly-defined notification must have the value zero
Status: current Access: read-write
OBJECT-IDENTITY    

lntPortCAMLastChange 3.1.81.38.4.0.22
This trap reports of the occurred CAM changes
Status: obsolete Access: read-write
NOTIFICATION-TYPE    

lntPSUEvents 3.1.81.38.5
Groups together all Power supply related events
Status: current Access: read-write
OBJECT-IDENTITY    

lntPSUPrefix 3.1.81.38.5.0
The next to last sub- identifier in the name of any newly-defined notification must have the value zero
Status: current Access: read-write
OBJECT-IDENTITY    

lntMainPSUFlt 3.1.81.38.5.0.2303
An error was reported concerning the Main Power Supply. Urgent intervention is required by the network administrator in order to replace the faulty module, or take any other necessary measures in order to ensure the uninterrupted operation of the network
Status: current Access: read-write
NOTIFICATION-TYPE    

lntMainPSUOk 3.1.81.38.5.0.2304
The network device recovered after a previously reported problem in the operation of the box Main Power Supply
Status: current Access: read-write
NOTIFICATION-TYPE    

lntBackupPSUFlt 3.1.81.38.5.0.2305
An error was reported concerning the Backup Power Supply. Urgent intervention is required by the network administrator in order to replace the faulty module, or take any other necessary measures in order to ensure the uninterrupted operation of the network.
Status: current Access: read-write
NOTIFICATION-TYPE    

lntBackupPSUOk 3.1.81.38.5.0.2306
The network device recovered after a previously reported problem in the operation of the box Backup Power Supply.
Status: current Access: read-write
NOTIFICATION-TYPE    

lntL3Events 3.1.81.38.6
Groups together routing( L3) related events.
Status: current Access: read-write
OBJECT-IDENTITY    

lntL3FaultsPrefix 3.1.81.38.6.0
The next to last sub- identifier in the name of any newly-defined notification must have the value zero
Status: current Access: read-write
OBJECT-IDENTITY    

lntDuplicateIPFlt 3.1.81.38.6.0.27
This trap reports to the Management station on Duplicate IP identification. CRP identify the new IP on the network. If it similar to one of its IP interfaces, the CRP will issue a SNMP trap, containing the MAC of the intruder.
Status: current Access: read-write
NOTIFICATION-TYPE    

lntVLANViolationEvent 3.1.81.38.6.0.28
This trap reports to the Management station on IP VLAN violation. CRP verify the VLAN of the incoming packets. If there is any inconsistency between the configured VLAN and the VLAN number found in the IP packet, the CRP will issue a SNMP trap.
Status: current Access: read-write
NOTIFICATION-TYPE    

lntARPViolationEvent 3.1.81.38.6.0.70
This trap reports to the Management station when a Sourec IP in an ARP response does not match the subnets configured on the router interface through which it has been received. The trap returns details of the offending packet, as welll as the expected vs. detected VLAN IDs and interface Names
Status: current Access: read-write
NOTIFICATION-TYPE    

lntLinkEvents 3.1.81.38.7
Groups together port link up/down related events.
Status: current Access: read-write
OBJECT-IDENTITY    

lntLinkEventsPrefix 3.1.81.38.7.0
The next to last sub- identifier in the name of any newly-defined notification must have the value zero
Status: current Access: read-write
OBJECT-IDENTITY    

lntPortLinkDownEvent 3.1.81.38.7.0.3039
The port hardware detects loss of connectivity to an end station or to another hub or switch. This is not necessarily a fault condition, as the same signaling is reported by the port hardware in usual operational cases, for example, of a non-critical station being disconnected or turned off at the end of the work day. (Bit 7 in the genPortFaultMask set to on, genPortFunctionalStatus = rld(2) )
Status: current Access: read-write
NOTIFICATION-TYPE    

lntPortLinkUpEvent 3.1.81.38.7.0.3040
The port recovered from a previously reported connectivity problem. (Bit 7 in the genPortFaultMask set to off, genPortFunctionalStatus = ok)
Status: current Access: read-write
NOTIFICATION-TYPE    

lntVPortLinkDownEvent 3.1.81.38.7.0.3041
The port hardware detects the lack of a connection to an end station or to another hub or switch. While this may not be necessarily a fault condition, the network administrator's attention is recommended, because the port was defined as a valuable port. (Bit 7 in the genPortFaultMask set to on, genPortFunctionalStatus = rld(2))
Status: current Access: read-write
NOTIFICATION-TYPE    

lntVPortLinkUpEvent 3.1.81.38.7.0.3042
Acknowledegs link up condition on a valuable port. (Bit 7 in the genPortFaultMask set to off, genPortFunctionalStatus = ok)
Status: current Access: read-write
NOTIFICATION-TYPE    

lntLAGEvents 3.1.81.38.8
Groups together LAG related events.
Status: current Access: read-write
OBJECT-IDENTITY    

lntLAGPrefix 3.1.81.38.8.0
The next to last sub- identifier in the name of any newly-defined notification must have the value zero
Status: current Access: read-write
OBJECT-IDENTITY    

lntLAGConnLostFlt 3.1.81.38.8.0.44
The trap reports on a LAG connection lost. It is sent when scGenLinkAggregationFunctionalStatus changed to fail (2).
Status: current Access: read-write
NOTIFICATION-TYPE    

lntLAGConnLostOk 3.1.81.38.8.0.46
The trap reports that the LAG connection lost was cleared. It is sent when scGenLinkAggregationFunctionalStatus changed from fail(2) to to ok(1).
Status: current Access: read-write
NOTIFICATION-TYPE    

lntLAGPartialConnLostFlt 3.1.81.38.8.0.48
The trap reports on a LAG partial connection, where some of the ports are in fault but some are ok. It is sent when scGenLinkAggregationFunctionalStatus changed to partialFail (3).
Status: current Access: read-write
NOTIFICATION-TYPE    

lntLAGPartialConnLostOk 3.1.81.38.8.0.50
The trap reports that the LAG partial connection was cleared. It is sent when scGenLinkAggregationFunctionalStatus changed from partialFail (3)to to ok(1).
Status: current Access: read-write
NOTIFICATION-TYPE    

lntLAGAutoNegFlt 3.1.81.38.8.0.52
The trap reports on a auto-negotiation results on the LAG ports. It is sent when scGenLinkAggregationAutoNegResults changed to autoNegInconsistantResults (2).
Status: current Access: read-write
NOTIFICATION-TYPE    

lntLAGAutoNegOk 3.1.81.38.8.0.54
The trap reports that the auto-negotiation results on the LAG ports was cleared. It is sent when this trap is enabled and when scGenLinkAggregationAutoNegResults changed to ok(1).
Status: current Access: read-write
NOTIFICATION-TYPE    

lntLAGDeleteEvent 3.1.81.38.8.0.56
The trap notifies the manager of the deletion of the specified LAG, which is identified by the scGenLinkAggregationId.
Status: current Access: read-write
NOTIFICATION-TYPE    

lntLAGCreateEvent 3.1.81.38.8.0.58
The trap is generated on the creation of a new LAG, which is identified by the scGenLinkAggregationId.
Status: current Access: read-write
NOTIFICATION-TYPE    

lntFansEvents 3.1.81.38.9
Groups together fans related events.
Status: current Access: read-write
OBJECT-IDENTITY    

lntFansPrefix 3.1.81.38.9.0
The next to last sub- identifier in the name of any newly-defined notification must have the value zero
Status: current Access: read-write
OBJECT-IDENTITY    

lntMainFansFlt 3.1.81.38.9.0.2307
The trap reports the failure of one (or more) module's Fan. It is sent when scGenGroupFansStatus changed to oneFanFailed(2)
Status: current Access: read-write
NOTIFICATION-TYPE    

lntMainFansOK 3.1.81.38.9.0.2308
The trap reports that the module's Fan failure was cleared. It is sent when this trap is enabled and when scGenGroupFansStatus changed from oneFanFailed(2) to allFansOK(1).
Status: current Access: read-write
NOTIFICATION-TYPE    

lntBackupFansFlt 3.1.81.38.9.0.2309
The trap reports the failure of one (or more) BUPS module's Fan. It is sent when scGenGroupBUPSFansStatus changed to oneFanFailed(2).
Status: current Access: read-write
NOTIFICATION-TYPE    

lntBackupFansOK 3.1.81.38.9.0.2310
The trap reports that the BUPS module's Fan failure was cleared. It is sent when this trap is enabled and when scGenGroupBUPSFansStatus changed from oneFanFailed(2) to allFansOK(1).
Status: current Access: read-write
NOTIFICATION-TYPE    

lntCascadeEvents 3.1.81.38.10
Groups together stakc module cascading related events.
Status: current Access: read-write
OBJECT-IDENTITY    

lntCascadeFaultsPrefix 3.1.81.38.10.0
The next to last sub- identifier in the name of any newly-defined notification must have the value zero
Status: current Access: read-write
OBJECT-IDENTITY    

lntCascadUpConnFlt 3.1.81.38.10.0.2315
The trap reports on a cascading up connection lost. It is sent when genGroupCascadUpStatus changed to rld(2).
Status: current Access: read-write
NOTIFICATION-TYPE    

lntCascadUpConnOk 3.1.81.38.10.0.2316
The trap reports that the cascading up connection lost was cleared. It is sent when genGroupCascadUpStatus changed from rld(2) to ok(1).
Status: current Access: read-write
NOTIFICATION-TYPE    

lntCascadDownConnFlt 3.1.81.38.10.0.2317
The trap reports on a cascading down connection lost. It is sent when genGroupCascadDownStatus changed to rld(2).
Status: current Access: read-write
NOTIFICATION-TYPE    

lntCascadDownConnOk 3.1.81.38.10.0.2318
The trap reports that the cascading down connection lost was cleared. It is sent when genGroupCascadDownStatus changed from rld(2) to ok(1).
Status: current Access: read-write
NOTIFICATION-TYPE    

lntPolicyEvents 3.1.81.38.11
Groups together policy related events.
Status: current Access: read-write
OBJECT-IDENTITY    

lntPolicyPrefix 3.1.81.38.11.0
The next to last sub- identifier in the name of any newly-defined notification must have the value zero
Status: current Access: read-write
OBJECT-IDENTITY    

lntPolicyChangeEvent 3.1.81.38.11.0.60
The trap reports a change in the active list specific for a policy-enabled box or module
Status: current Access: read-write
NOTIFICATION-TYPE    

lntPolicyAccessControlListLvlRuleTrap 3.1.81.38.11.0.62
This trap reports to the Management station when a list-level Policy rule (e.g., ipPolicyListIpOptionOperation) specifies an operation that includes a 'notify' action. The trap includes in its varbind information about: - The entity (slot) where the event occurred, - The type of the list-level rule that was matched, - The quintuplet that identifies the matching packet. - The policy interface on which the event occurred. - The policy interface sub-context (e.g., the direction) - sysUpTime at the time the event occured. A management application would display this trap and the relevant information in a log entry. This trap will not be sent at intervals smaller than one minute for identical information in the varbinds list variables.
Status: current Access: read-write
NOTIFICATION-TYPE    

lntPolicyAccessControlViolationFlt 3.1.81.38.11.0.64
This trap reports to the Management station on IP PolicyAccess Control violation. The trap includes in its varbind information about the slot where the event occurred, The id of the rule that was violated in the current rules table, and the quintuplet that identifies the faulty packet. A management application would display this trap and the relevant information in a log entry. This trap will not be sent at intervals smaller than one minute for identical information in the varbinds list variables
Status: current Access: read-write
NOTIFICATION-TYPE    

lntEthPortFaultEvents 3.1.81.38.12
Groups together Etherent port related events.
Status: current Access: read-write
OBJECT-IDENTITY    

lntEthPortFaultPrefix 3.1.81.38.12.0
The next to last sub- identifier in the name of any newly-defined notification must have the value zero
Status: current Access: read-write
OBJECT-IDENTITY    

lntEthPortAutoNegotiationFlt 3.1.81.38.12.0.3001
The port recovered from a previously reported connectivity problem. (Bit 4 in the genPortFaultMask set to off, scEthPortAutoNegotiationStatus = ok)
Status: current Access: read-write
NOTIFICATION-TYPE    

lntEthPortAutoNegotiationOK 3.1.81.38.12.0.3002
The port recovered from a previously reported connectivity problem. (Bit 4 in the genPortFaultMask set to off, scEthPortAutoNegotiationStatus = ok)
Status: current Access: read-write
NOTIFICATION-TYPE    

lntPortFEFlt 3.1.81.38.12.0.3005
The port hardware detects a loss of connectivity reported by the remote extremity of the link connected to the port. This indication shows that though the cabling is at least partially operative, the information transmitted through the port may not arrive in all its integrity at the other side of the link. It is recommended that the network administrator check the link in order to detect the origin of the problem and prevent its aggravation. (Bit 10 in the genPortFaultMask set to on)
Status: current Access: read-write
NOTIFICATION-TYPE    

lntPortFEOk 3.1.81.38.12.0.3006
A previously detected problem in the integrity of the link, reported by the remote link circuitry was solved. (Bit 10 in the genPortFaultMask set to off, scEthPortFunctionalStatus = ok(1))
Status: current Access: read-write
NOTIFICATION-TYPE    

lntVPortFEFlt 3.1.81.38.12.0.3015
The valuable port hardware detects a loss of connectivity reported by the remote extremity of the link connected to the port. This indication shows that though the cabling is at least partially operative, the information transmitted through the port may not arrive in all its integrity at the other side of the link. It is recommended that the network administrator check the link in order to detect the origin of the problem and prevent its aggravation. (Bit 10 in the genPortFaultMask set to on, scEthPortFunctionalStatus = fail(2))
Status: current Access: read-write
NOTIFICATION-TYPE    

lntVPortFEOk 3.1.81.38.12.0.3016
A previously detected problem in the integrity of the link to a valuable port, reported by the remote link circuitry was solved. (Bit 10 in the genPortFaultMask set to off, scEthPortFunctionalStatus = ok(1))
Status: current Access: read-write
NOTIFICATION-TYPE    

lntPortAutoPartFlt 3.1.81.38.12.0.3023
The port on the module reports the activation of the auto partition mechanism. This event means that an excessive number of errors occurred on the port, and the port is disconnected from the repeater or switch unit. The network administrator should check the segment and/or end stations connected to the port for hardware or misconfiguration problems. (Bit 1 in the genPortFaultMask set to on, genPortFunctionalStatus = partition(8))
Status: current Access: read-write
NOTIFICATION-TYPE    

lntPortAutoPartOk 3.1.81.38.12.0.3024
The port recovered from a previously reported auto partition fault. (Bit 1 in the genPortFaultMask set to off, genPortFunctionalStatus = ok)
Status: current Access: read-write
NOTIFICATION-TYPE    

lntVPortAutoPartFlt 3.1.81.38.12.0.3025
The valuable port on the module reports the activation of the autopartition mechanism. This event means that an excessive number of errors occurred on the port, and the port is disconnected from the repeater or switch unit. The network administrator should check the segment and/or end stations connected to the port for hardware or misconfiguration problems. (Bit 1 in the genPortFaultMask set to on, genPortFunctionalStatus = partition(8))
Status: current Access: read-write
NOTIFICATION-TYPE    

lntVPortAutoPartOK 3.1.81.38.12.0.3026
The valuable port recovered from a previously reported auto partition fault. (Bit 1 in the genPortFaultMask set to off, genPortFunctionalStatus = ok)
Status: current Access: read-write
NOTIFICATION-TYPE    

lntEthVPortAutoNegotiationFlt 3.1.81.38.12.0.3031
The valuable port hardware detects the lack of a connection to an end station or to another hub or switch. While this is may not be necessarily a fault condition, the network administrator's attention is recommended, because the port was defined as a port. (Bit 4 in the genPortFaultMask set to on, scEthPortAutoNegotiationStatus = fail(2))
Status: current Access: read-write
NOTIFICATION-TYPE    

lntEthVPortAutoNegotiationOK 3.1.81.38.12.0.3032
The port hardware detects the lack of a connection to an end station or to another hub or switch. While this is may not be necessarily a fault condition, the network administrator's attention is recommended, because the port was defined as a valuable port. (Bit 4 in the genPortFaultMask set to on, scEthPortAutoNegotiationStatus = fail(2))
Status: current Access: read-write
NOTIFICATION-TYPE    

lntPortInlinePowerFlt 3.1.81.38.12.0.3933
The Inline Power (Power-over-Ethernet) port hardware reports that the PD (Powered device) connected to that port is not receiving Inline Power due to a fault condition. (Bit 37 in the genPortFaultMask set to on, pethPsePortDetectionStatus = fault(4) or otherfault(6))
Status: current Access: read-write
NOTIFICATION-TYPE    

lntPortInlinePowerOK 3.1.81.38.12.0.3934
The Inline Power (Power-over-Ethernet) port hardware reports that the PD (Powered device) connected to that port is not in a fault condition. It may or not be delievering Inline Power to the PD. (Bit 37 in the genPortFaultMask set to on, pethPsePortDetectionStatus = fault(4) or otherfault(6))
Status: current Access: read-write
NOTIFICATION-TYPE    

lntSecurityEvents 3.1.81.38.13
Description.
Status: current Access: read-write
OBJECT-IDENTITY    

lntSecurityPrefix 3.1.81.38.13.0
Description.
Status: current Access: read-write
OBJECT-IDENTITY    

lntUnAuthAccessEvent 3.1.81.38.13.0.68
Notification on unauthorized login attempts. o For CLI and SNMP login failures: Both SNMP SSH and WEB management interfaces shall identify situation and alert. The reported information should include wrong user name, host name and IP address of remote host. Passwords is not reported because of the possibility to reveal password. o For pre-shared-key (PSK) authentication failure in IKE: * lntUnauthUserName - - In IKE AM: the ID sent by the remote peer in the ID payload. - In IKE MM: the ID associated with the remote peer IP in the running configuration. * lntUnauthIpAddress - the source IP of the packet sent by the remote peer. * lntUnauthProtocol - lntIKEAccess(500)
Status: current Access: read-write
NOTIFICATION-TYPE    

lntMACSecurityEvent 3.1.81.38.13.0.104
This trap notifies the management station of the security violation. It gives the slot number of the board, the port on the board and the source MAC address extracted from the frame that has violated the security policy. The slot and the port numbers, genPortGroupId and genPortId respectively, define an instance of the appropriate source address.For the ring security violation the trap contains the ring ID and the intruder's MAC address. The trap was previously assigned the specific number 11.
Status: current Access: read-write
NOTIFICATION-TYPE    

lntUnknownHostCopyEvent 3.1.81.38.13.0.1002
Event generated on attempt to accomplish download/upload file transfer using SCP/SFTP protocol to unknown host.
Status: current Access: read-write
NOTIFICATION-TYPE    

lntAccountLockoutEvent 3.1.81.38.13.0.1003
After configurable number of failed attempts to authenticate a user, device penalized by locking them out for a pre-specified amount of time.
Status: current Access: read-write
NOTIFICATION-TYPE    

lntLicenseStartupValidationFlt 3.1.81.38.13.0.1004
At start-up, the product validates the license file scheme and the license signature. On inconsistency the product issues this tarp and then returns to the factory-default feature activation settings.
Status: current Access: read-write
NOTIFICATION-TYPE    

lntLicenseDownloadValidationFlt 3.1.81.38.13.0.1005
During the license file download, the product validates the license file scheme and the license signature. On inconsistency the product aborts download process, sends this notification and stay with the existing feature activation settings
Status: current Access: read-write
NOTIFICATION-TYPE    

lntDot1xMaxAuthRateReachedEvent 3.1.81.38.13.0.1006
This trap notifies the management station that maximum rate of 802.1x authentications has been reached in module $1 .
Status: current Access: read-write
NOTIFICATION-TYPE    

lntDot1xAuthFailureEvent 3.1.81.38.13.0.1007
This trap notifies the management station that device with MAC address $1 failed to authenticate module/port $2/$3 due to $4
Status: current Access: read-write
NOTIFICATION-TYPE    

lntDot1xMaxAuthModuleNumReachedEvent 3.1.81.38.13.0.1008
This trap notifies the management station that Authentication denied due to maximum number of authentication of 802.1x $1 per module $2 has been reached.
Status: current Access: read-write
NOTIFICATION-TYPE    

lntDot1xMaxAuthPortNumReachedEvent 3.1.81.38.13.0.1009
This trap notifies the management station that Authentication denied due to maximum number of authentication of 802.1x $1 per module/port $2/$3 has been reached.
Status: current Access: read-write
NOTIFICATION-TYPE    

lntNotificationVarbinds 3.1.81.38.14
Description.
Status: current Access: read-write
OBJECT-IDENTITY    

lntConfigChangeValue 3.1.81.38.14.1
The text formatted value of MIB object at the time change configuration has occured
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString  

lntConfigChangeOID 3.1.81.38.14.2
This variable used to signal the OID of MIB object that had changed its status and triggered the Change Configuration event
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  OBJECT IDENTIFIER  

lntUnauthUserName 3.1.81.38.14.3
The name of the user who's attempt to access device was identified as unauthorized.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

lntUnauthIpAddress 3.1.81.38.14.4
The IP address of access violating station
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  IpAddress  

lntUnauthProtocol 3.1.81.38.14.5
The management protocol employed for the unauthorized access - lntSSHAccess(22) -- SSH protocol lntTELNETAccess(23), --Telnet protocol lntHTTPAccess(80), -- HTTP protocol lntSNMPAccess(161), -- SNMP protocol lntHTTPSAccess(443), -- HTTPS protocol over TLS sockets lntIKEAccess(500), -- IKE protocol - PSK authentication failure lntRASAccess(6889), -- RAS access over dial-up connection lntConsoleAccess(6890), -- Access from the Console port lntPPPAccess(6891) -- Access to PPP over modem
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER lntSSHAccess(22), lntTELNETAccess(23), lntHTTPAccess(80), lntSNMPAccess(161), lntHTTPSAccess(443), lntIKEAccess(500), lntRASAccess(6889), lntConsoleAccess(6890), lntPPPAccess(6891)  

lntSCPStrictCheckingMode 3.1.81.38.14.6
The SCP setting on validity of the public key reported by the SCP server. If strict setting is yes - then new keys not registered already in hosts file will be discard and copy operation is aborted. No - device registers new hosts and proceded with copy operation, ask - requires interactive sessions with the operator ( must fail the SNMP non interactive request)
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER yes(1), no(2), ask(3)  

lntLicenseErrorCodes 3.1.81.38.14.7
Product reports following errors if license validations fails lntSerialNumMismatch(1), - Serial number mismatch between license file and gateway hardware lntInvalidSignature(2), - Invalid digital signature on the license file lntPlatformTypeMismatch(3), - Mismatch between product platform type defined in license file (for example G250) and the gateway type (e.g. G350). lntInvalidLicFeture(4) - Invalid feature setting.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER lntSerialNumMismatch(1), lntInvalidSignature(2), lntPlatformTypeMismatch(3), lntInvalidLicFeture(4)  

scGenPortDot1xFailureString 3.1.81.38.14.8
The text formatted value of MIB object at the time when 802.1x authentication is failed.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString  

lntWanEvents 3.1.81.38.15
Description.
Status: current Access: accessible-for-notify
OBJECT-IDENTITY    

lntWanPrefix 3.1.81.38.15.0
Description.
Status: current Access: accessible-for-notify
OBJECT-IDENTITY    

lntWanPhysicalAlarmOn 3.1.81.38.15.0.30
Description.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

lntWanPhysicalAlarmOff 3.1.81.38.15.0.31
Description.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

lntWanLocalAlarmOn 3.1.81.38.15.0.32
Description.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

lntWanLocalAlarmOff 3.1.81.38.15.0.33
Description.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

lntWanRemoteAlarmOn 3.1.81.38.15.0.34
Description.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

lntWanRemoteAlarmOff 3.1.81.38.15.0.35
Description.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

lntWanMinorAlarmOn 3.1.81.38.15.0.36
Description.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

lntWanMinorAlarmOff 3.1.81.38.15.0.37
Description.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

lntNotificationGroups 3.1.81.38.10007
OBJECT IDENTIFIER    

lntConfigChangeVarbinds 3.1.81.38.10007.1
varbinds related with config change trap
Status: current Access: accessible-for-notify
OBJECT-GROUP    

lntLagNotificationGroup 3.1.81.38.10007.5
Group of Link aggregation traps
Status: current Access: accessible-for-notify
NOTIFICATION-GROUP    

lntSWRedundancyNotificationGroup 3.1.81.38.10007.6
Group of Software Redundancy traps
Status: current Access: accessible-for-notify
NOTIFICATION-GROUP    

lntPSUFaultNotificationGroup 3.1.81.38.10007.7
PSU related fault traps (main and backup)
Status: current Access: accessible-for-notify
NOTIFICATION-GROUP    

lntTempratureNotificationGroup 3.1.81.38.10007.8
Temperature warning related traps
Status: current Access: accessible-for-notify
NOTIFICATION-GROUP    

lntL3FaultNotificationGroup 3.1.81.38.10007.9
Group of L3 fault traps
Status: current Access: accessible-for-notify
NOTIFICATION-GROUP    

lntLinkDownNotificationGroup 3.1.81.38.10007.10
Link Down/Up traps
Status: current Access: accessible-for-notify
NOTIFICATION-GROUP    

lntCascadeNotificationGroup 3.1.81.38.10007.11
Cascade fault traps
Status: current Access: accessible-for-notify
NOTIFICATION-GROUP    

lntEthPortNotificationGroup 3.1.81.38.10007.12
Eth port fault traps
Status: current Access: accessible-for-notify
NOTIFICATION-GROUP    

lntCAMNotificationGroup 3.1.81.38.10007.13
CAM change related traps
Status: obsolete Access: accessible-for-notify
NOTIFICATION-GROUP    

lntConfigChangeNotificationGroup 3.1.81.38.10007.14
Configuration change related traps
Status: current Access: accessible-for-notify
NOTIFICATION-GROUP    

lntPolicyNotificationGroup 3.1.81.38.10007.15
policy related traps
Status: current Access: accessible-for-notify
NOTIFICATION-GROUP    

lntFansNotificationGroup 3.1.81.38.10007.16
Notifications related with FAN problems
Status: current Access: accessible-for-notify
NOTIFICATION-GROUP    

lntSecurityNotificationGroup 3.1.81.38.10007.17
Description.
Status: current Access: accessible-for-notify
NOTIFICATION-GROUP    

lntWanNotificationGroup 3.1.81.38.10007.18
Description.
Status: current Access: accessible-for-notify
NOTIFICATION-GROUP    

lntNotificationAgentCapabilities 3.1.81.38.10008
OBJECT IDENTIFIER    

lntP330L3NotificationAgentCapabilities 3.1.81.38.10008.1
Trap Capabilities of P330 L3 Device.
Status: current Access: accessible-for-notify
AGENT-CAPABILITIES    

lntP330L2NotificationAgentCapabilities 3.1.81.38.10008.2
Trap capabilities of P330 L2 device.
Status: current Access: accessible-for-notify
AGENT-CAPABILITIES    

lntP130TrapAgentCapabilities 3.1.81.38.10008.3
Trap capabilities of P130 device.
Status: current Access: accessible-for-notify
AGENT-CAPABILITIES    

lntP330MLNotificationAgentCapabilities 3.1.81.38.10008.4
Traps supported by P330ML device.
Status: current Access: accessible-for-notify
AGENT-CAPABILITIES    

lntG350NotificationAgentCapability 3.1.81.38.10008.5
Description.
Status: current Access: accessible-for-notify
AGENT-CAPABILITIES