LSI-MegaRAID-SAS-MIB

File: LSI-MegaRAID-SAS-MIB.mib (212707 bytes)

Imported modules

RFC1155-SMI RFC1213-MIB RFC-1212
RFC-1215

Imported symbols

private enterprises Counter
Gauge PhysAddress DisplayString
OBJECT-TYPE TRAP-TYPE

Defined Types

AdapterPropertiesEntry  
SEQUENCE    
  adapterID-APT INTEGER
  rebuildRate INTEGER
  reconstructionRate INTEGER
  alarmState INTEGER
  cacheFlushInterval INTEGER
  clusterState INTEGER
  predFailPollInterval INTEGER
  intThrottleCount INTEGER
  intThrottleTimeUs INTEGER
  patrolReadRate INTEGER
  bgiRate INTEGER
  spinupDelay INTEGER
  spinupDriveCount INTEGER
  coercionMode INTEGER
  nvramSize INTEGER
  memorySize INTEGER
  flashSize INTEGER
  vdPresentCount INTEGER
  vdDegradedCount INTEGER
  vdOfflineCount INTEGER
  pdPresentCount INTEGER
  pdDiskPresentCount INTEGER
  pdDiskPredFailureCount INTEGER
  pdDiskFailedCount INTEGER
  ccRate INTEGER
  compatibilityFlag INTEGER
  compatibilityInfo DisplayString
  abortCConError INTEGER
  copyBackState INTEGER
  multipathSupport INTEGER
  revisionIdentifier DisplayString
  ssdSMARTerEnabled INTEGER
  enableSpinDownUnconfigured INTEGER
  disableSpinDownHotSpare INTEGER
  spinDownTime INTEGER
  supportBreakMirror INTEGER
  spinupEnclDriveCount INTEGER
  spinupEnclDelay INTEGER
  defaultLdPSPolicy INTEGER
  disableLdPSInterval INTEGER
  disableLdPSTime INTEGER
  temperatureROC INTEGER
  temperatureCtrl INTEGER
  preventPIImport INTEGER
  enablePI INTEGER
  totalSpaceformetadata INTEGER
  useEmergencySpare DisplayString
  useEmergencySparesforSMARTer INTEGER
  supportShieldState INTEGER
  writeCacheCapable INTEGER
  totalCacheSize INTEGER
  maximumCacheSize INTEGER
  ctrlSasAddr DisplayString
  domainId DisplayString
  peerControllerStatus DisplayString
  maximumControllerNodes INTEGER
  incompatibilityDetails DisplayString
  topologyType DisplayString
  supportOnlineFWUpdate INTEGER

AdapterInfoEntry  
SEQUENCE    
  adapterID-AIT INTEGER
  adapterVendorID DisplayString
  devID DisplayString
  subVendorID DisplayString
  subDevID DisplayString
  hostInterface INTEGER
  hostInterfacePortCnt INTEGER
  hostInterfacePortAddr DisplayString
  devInterface DisplayString
  devInterfacePortCnt INTEGER
  devInterfacePortAddr DisplayString
  productName DisplayString
  serialNo DisplayString
  firmwareVersion DisplayString
  driverVersion DisplayString
  expanderFirmwareVersion DisplayString
  lockKeyBinding INTEGER
  maxDAPdCountSpinup60 INTEGER

AdapterSupportInfoEntry  
SEQUENCE    
  adapterID-ASIT INTEGER
  maxArms INTEGER
  maxSpans INTEGER
  maxArrays INTEGER
  maxVDs INTEGER
  hardwarePresent DisplayString
  maxConcurrentCmds INTEGER
  maxSGECount INTEGER
  maxRequestSize INTEGER
  maxLdsPerArray INTEGER
  partitionsInDDF INTEGER
  allowSSDMixInLD INTEGER
  allowMixSSDHDDInLD INTEGER

AdapterOperationsSupportInfoEntry  
SEQUENCE    
  adapterID INTEGER
  rbldRateSupported INTEGER
  ccRateSupported INTEGER
  bgiRateSupported INTEGER
  reconRateSupported INTEGER
  patrolRateSupported INTEGER
  alarmControlSupported INTEGER
  clusterSupported INTEGER
  bbuSupported INTEGER
  spanningAllowedSupported INTEGER
  dedicatedHotSparesSupported INTEGER
  revertibleHotSparesSupported INTEGER
  foreignConfigImportSupported INTEGER
  selfDiagnosticSupported INTEGER
  allowMixedRedundancyOnArraySupported INTEGER
  abortCConErrorSupported INTEGER
  securitySupported INTEGER
  supportPIcontroller INTEGER

BBUEntry  
SEQUENCE    
  bbuID INTEGER
  batteryType DisplayString
  nextLearnTime INTEGER
  absStateOfCharge INTEGER
  fullChargeCapacity INTEGER
  averageEmptyTime INTEGER
  cycleCount INTEGER
  firmwareStatus DisplayString
  voltage INTEGER
  autoLearnPeriod INTEGER
  relStateOfCharge INTEGER
  capacityRemain INTEGER
  runTimeToEmpty INTEGER
  avgTimeToFull INTEGER
  errorMargin INTEGER
  temperature DisplayString
  mfgName DisplayString
  deviceName DisplayString
  serialNumber DisplayString
  chargerStatus INTEGER
  adpID INTEGER
  remainingCapAlarm INTEGER
  remainingTimeAlarm INTEGER
  bbu-current INTEGER
  gasGaugeStatus INTEGER
  bbuFRU DisplayString
  batteryReplacement INTEGER
  bbuRetentiontime DisplayString
  bbuState DisplayString
  memoryModuleFRU DisplayString
  bbuFirmwareVersion DisplayString

AdapterStatusSupportInfoEntry  
SEQUENCE    
  adapterID-ASSIT INTEGER
  lockKeyAssigned INTEGER
  lockKeyFailed INTEGER
  lockKeyNotBackedup INTEGER
  biosNotDetected INTEGER
  cacheIsPinned INTEGER

AdapterLdOperationSupportInfoEntry  
SEQUENCE    
  adapterID-ALSIT INTEGER
  allowCtrlEncryption INTEGER

CommonDeviceInfoEntry  
SEQUENCE    
  adapterID-CDIT INTEGER
  forceOnline INTEGER
  forceOffline INTEGER
  forceRebuild INTEGER
  supportsSAS INTEGER
  supportsSATA INTEGER
  allowMixInEnclosure INTEGER
  allowMixInVD INTEGER
  allowSataInCluster INTEGER
  setPowerStateForCfg INTEGER

PhysicalDriveEntry  
SEQUENCE    
  pdIndex INTEGER
  physDevID INTEGER
  oemSupported INTEGER
  scsiDevType INTEGER
  connectedAdapterPort DisplayString
  deviceSpeed INTEGER
  mediaErrCount INTEGER
  otherErrCount INTEGER
  predFailCount INTEGER
  pdState INTEGER
  disabledForRemoval INTEGER
  linkSpeed INTEGER
  pdSupportFlags DisplayString
  sasAddr DisplayString
  rawSize INTEGER
  nonCoercedSize INTEGER
  coercedSize INTEGER
  enclDeviceId INTEGER
  enclIndex INTEGER
  slotNumber INTEGER
  operationProgress DisplayString
  adpID-PDT INTEGER
  operationSupport DisplayString
  pdVendorID DisplayString
  pdProductID DisplayString
  pdFwversion DisplayString
  diskType INTEGER
  partnerDevId INTEGER
  mediatype INTEGER
  powerState INTEGER
  secured INTEGER
  locked INTEGER
  foreign INTEGER
  oemCertified INTEGER
  foreignImportNotAllowed INTEGER
  pdTemperature INTEGER
  pdSerialNumber DisplayString
  piEligible INTEGER
  piType INTEGER
  piFormatted INTEGER
  userDataBlockSize INTEGER
  commissionedSpare DisplayString
  emergencySpare DisplayString
  shieldCounter INTEGER
  shieldDiagCompletionTime DisplayString
  ineligibleForSSCD INTEGER
  ineligibleForLd INTEGER

CommonVirtualDeviceInfoEntry  
SEQUENCE    
  adapterID-CVDIT INTEGER
  supportedReadPolicy INTEGER
  supportedWritePolicy INTEGER
  supportedIOPolicy INTEGER
  supportedAccessPolicy INTEGER
  supportedMinSize INTEGER
  supportedMaxSize INTEGER
  ldbbm INTEGER

VirtualDriveEntry  
SEQUENCE    
  virtualDevID INTEGER
  size INTEGER
  clusterOwnerDeviceId INTEGER
  targetId INTEGER
  state INTEGER
  name DisplayString
  defaultCachePolicy DisplayString
  accessPolicy INTEGER
  diskCachePolicy INTEGER
  bgiState INTEGER
  prl INTEGER
  rLQ INTEGER
  sRL INTEGER
  stripeSize INTEGER
  numDrives INTEGER
  spanDepth INTEGER
  initState INTEGER
  vdOperationProgress DisplayString
  currentCachePolicy DisplayString
  adapterID-VDT INTEGER
  encryptionType INTEGER
  vdOperationSupport DisplayString
  badBlocksExist INTEGER
  defaultPSPolicy INTEGER
  currentPSPolicy INTEGER
  breakMirror INTEGER
  joinMirror INTEGER
  mirrorPdInfo DisplayString
  vdPiType INTEGER
  mirrorDataSize INTEGER
  cacheCadeType INTEGER
  currentWritePolicy DisplayString
  defaultWritePolicy DisplayString
  associatedVD DisplayString
  hostAccessPolicy DisplayString
  guid DisplayString

VDSpanInfoEntry  
SEQUENCE    
  spanID INTEGER
  vdID-VSIT INTEGER
  startBlock INTEGER
  numBlocks DisplayString
  vdSpanArrayRef INTEGER
  adapterID-VSIT INTEGER

ArrayEntry  
SEQUENCE    
  arrayID INTEGER
  arraySize INTEGER
  arrayNumDrives INTEGER
  arrayRef INTEGER
  pdList DisplayString
  adapterID-AT INTEGER

SpareEntry  
SEQUENCE    
  spareID INTEGER
  deviceIdentification INTEGER
  spareType DisplayString
  arrayCount INTEGER
  arrayIDs DisplayString
  adapterID-ST INTEGER

EnclosureEntry  
SEQUENCE    
  enclosureID INTEGER
  deviceId INTEGER
  enclosureIndex INTEGER
  slotCount INTEGER
  psCount INTEGER
  fanCount INTEGER
  tempSensorCount INTEGER
  alarmCount INTEGER
  simCount INTEGER
  isFault INTEGER
  pdCount INTEGER
  pdIds DisplayString
  adapterID-ET INTEGER
  pdCountSpinup60 INTEGER
  enclosureType INTEGER
  enclFirmwareVersion DisplayString
  enclSerialNumber DisplayString
  vendorID DisplayString
  productID DisplayString
  eSMSerialNumber DisplayString
  eSMFRU DisplayString
  enclosureZoningMode DisplayString
  eSMFRUPartInfo DisplayString

EnclosureFanEntry  
SEQUENCE    
  fanID INTEGER
  enclosureId INTEGER
  fanStatus INTEGER

EnclosureSlotEntry  
SEQUENCE    
  slotID INTEGER
  enclosureId-EST INTEGER
  slotStatus INTEGER

EnclosurePowerSupplyEntry  
SEQUENCE    
  powerSupplyID INTEGER
  enclosureId-EPST INTEGER
  powerSupplyStatus INTEGER

EnclosureTempSensorEntry  
SEQUENCE    
  tempSensorID INTEGER
  enclosureId-ETST INTEGER
  tempSensorStatus INTEGER
  enclosureTemperature INTEGER

EnclosureAlarmEntry  
SEQUENCE    
  alarmID INTEGER
  enclosureId-EAT INTEGER
  alarmStatus INTEGER

EnclosureSIMEntry  
SEQUENCE    
  simID INTEGER
  enclosureId-ESIT INTEGER
  simStatus INTEGER

Defined Values

lsi 1.3.6.1.4.1.3582
OBJECT IDENTIFIER    

storageComponents 1.3.6.1.4.1.3582.4
OBJECT IDENTIFIER    

lsiRAIDServer 1.3.6.1.4.1.3582.4.1
OBJECT IDENTIFIER    

hostName 1.3.6.1.4.1.3582.4.1.1
Name of the host system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..63)  

hostOSInfo 1.3.6.1.4.1.3582.4.1.2
Operating System description where SNMP agent is running.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..63)  

versionInfo 1.3.6.1.4.1.3582.4.1.3
OBJECT IDENTIFIER    

mibVersion 1.3.6.1.4.1.3582.4.1.3.1
The MIB version no. (xx.yy)
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..63)  

agentModuleName 1.3.6.1.4.1.3582.4.1.3.2
The agent module name
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..63)  

agentModuleVersion 1.3.6.1.4.1.3582.4.1.3.3
The module version in xx.yy format. Where xx is the major version number and yy is the minor version number(without build information).
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..63)  

releaseDate 1.3.6.1.4.1.3582.4.1.3.4
Module Release Date
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..63)  

megaRAID-SAS 1.3.6.1.4.1.3582.4.1.4
OBJECT IDENTIFIER    

adapter 1.3.6.1.4.1.3582.4.1.4.1
OBJECT IDENTIFIER    

adpNumber 1.3.6.1.4.1.3582.4.1.4.1.1
The total no of SAS adapters present.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adapterPropertiesTable 1.3.6.1.4.1.3582.4.1.4.1.2
A List of adapter Entries containing Information/Properties about the adapters.
Status: optional Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdapterPropertiesEntry

adapterPropertiesEntry 1.3.6.1.4.1.3582.4.1.4.1.2.1
An Entry in the adapter table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdapterPropertiesEntry  

adapterID-APT 1.3.6.1.4.1.3582.4.1.4.1.2.1.1
AdapterID for this Adapter.(Unique)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

rebuildRate 1.3.6.1.4.1.3582.4.1.4.1.2.1.2
Rebuild rate on this Adapter.
Status: optional Access: read-write
OBJECT-TYPE    
  INTEGER 0..100  

reconstructionRate 1.3.6.1.4.1.3582.4.1.4.1.2.1.3
Reconstruction rate on this Adapter.
Status: optional Access: read-write
OBJECT-TYPE    
  INTEGER 0..100  

alarmState 1.3.6.1.4.1.3582.4.1.4.1.2.1.4
Alarm is enabled or disabled on this adapter. Values: disabled(0),enabled(1)
Status: optional Access: read-write
OBJECT-TYPE    
  INTEGER 0..1  

cacheFlushInterval 1.3.6.1.4.1.3582.4.1.4.1.2.1.5
Cache flush interval in seconds for this adapter.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

clusterState 1.3.6.1.4.1.3582.4.1.4.1.2.1.6
Cluster is enabled or disabled on this adapter. Values: disabled(0),enabled(1)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

predFailPollInterval 1.3.6.1.4.1.3582.4.1.4.1.2.1.7
Number of seconds between precdictive fail polls on this adapter.
Status: optional Access: read-write
OBJECT-TYPE    
  INTEGER  

intThrottleCount 1.3.6.1.4.1.3582.4.1.4.1.2.1.8
Interrupt throttle active count on this adapter.
Status: optional Access: read-write
OBJECT-TYPE    
  INTEGER  

intThrottleTimeUs 1.3.6.1.4.1.3582.4.1.4.1.2.1.9
Interrupt throttle completion hold time on this adapter.
Status: optional Access: read-write
OBJECT-TYPE    
  INTEGER  

patrolReadRate 1.3.6.1.4.1.3582.4.1.4.1.2.1.10
Patrol Read Rate for this adapter.
Status: optional Access: read-write
OBJECT-TYPE    
  INTEGER 0..100  

bgiRate 1.3.6.1.4.1.3582.4.1.4.1.2.1.11
Background initialization rate for this adapter.
Status: optional Access: read-write
OBJECT-TYPE    
  INTEGER 0..100  

spinupDelay 1.3.6.1.4.1.3582.4.1.4.1.2.1.12
Number of seconds to delay among spinup groups for this adapter.
Status: optional Access: read-write
OBJECT-TYPE    
  INTEGER  

spinupDriveCount 1.3.6.1.4.1.3582.4.1.4.1.2.1.13
Maximum number of drives to spin up at one time for this adapter.
Status: optional Access: read-write
OBJECT-TYPE    
  INTEGER  

coercionMode 1.3.6.1.4.1.3582.4.1.4.1.2.1.14
Drive capacity coercion mode. 0->None; 1->128MB; 2->1GB
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

nvramSize 1.3.6.1.4.1.3582.4.1.4.1.2.1.15
NVRAM size in KB for this adapter.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

memorySize 1.3.6.1.4.1.3582.4.1.4.1.2.1.16
Memory size in MB for this adapter.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

flashSize 1.3.6.1.4.1.3582.4.1.4.1.2.1.17
Flash size in MB for this adapter.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

vdPresentCount 1.3.6.1.4.1.3582.4.1.4.1.2.1.18
Virtual devices present in this adapter.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

vdDegradedCount 1.3.6.1.4.1.3582.4.1.4.1.2.1.19
Number of virtual devices in this adapter that are critical
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

vdOfflineCount 1.3.6.1.4.1.3582.4.1.4.1.2.1.20
Number of virtual devices in this adapter that are offline
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

pdPresentCount 1.3.6.1.4.1.3582.4.1.4.1.2.1.21
Physical devices present in this adapter.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

pdDiskPresentCount 1.3.6.1.4.1.3582.4.1.4.1.2.1.22
Physical disk devices present in this adapter.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

pdDiskPredFailureCount 1.3.6.1.4.1.3582.4.1.4.1.2.1.23
Number of disk devices in this adapter that are critical
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

pdDiskFailedCount 1.3.6.1.4.1.3582.4.1.4.1.2.1.24
Number of disk devices in this adapter that are failed
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

ccRate 1.3.6.1.4.1.3582.4.1.4.1.2.1.25
Consistency Check rate on this Adapter.
Status: optional Access: read-write
OBJECT-TYPE    
  INTEGER 0..100  

compatibilityFlag 1.3.6.1.4.1.3582.4.1.4.1.2.1.26
To inform compatibilities between Applications and FW. 0->incompatible; 1->compatible
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

compatibilityInfo 1.3.6.1.4.1.3582.4.1.4.1.2.1.27
Compatibility Information. Format->(Firmware Forward compatibility flag:Firmware Backward compatibility flag:Firmware version flag:Application Forward compatibility flag:Application Backward compatibility flag:Application version flag)
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

abortCConError 1.3.6.1.4.1.3582.4.1.4.1.2.1.28
Abort CC on detecting error is enabled or disabled on this adapter. Values: No(0),Yes(1),NA(2)
Status: optional Access: read-write
OBJECT-TYPE    
  INTEGER 0..1  

copyBackState 1.3.6.1.4.1.3582.4.1.4.1.2.1.29
CopyBack is enabled or disabled on this adapter.Values: disabled(0),enabled(1)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

revisionIdentifier 1.3.6.1.4.1.3582.4.1.4.1.2.1.30
Board revision ID for this Adapter.
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

multipathSupport 1.3.6.1.4.1.3582.4.1.4.1.2.1.31
Multipath is supported or not supported on this adapter.Values: not supported(0),supported(1)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

ssdSMARTerEnabled 1.3.6.1.4.1.3582.4.1.4.1.2.1.32
Copyback to SSD on SMART error. Values Enabled(0),Disabled(1)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

enableSpinDownUnconfigured 1.3.6.1.4.1.3582.4.1.4.1.2.1.33
Spin Down Unconfigured Drives(1), Do Not Spin Down Unconfigured Drives(0)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

disableSpinDownHotSpare 1.3.6.1.4.1.3582.4.1.4.1.2.1.34
Spin Down Hotspares(0), Do Not Spin Down Hotspares(1)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

spinDownTime 1.3.6.1.4.1.3582.4.1.4.1.2.1.35
SpinDownTime in minutes
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

spinupEnclDriveCount 1.3.6.1.4.1.3582.4.1.4.1.2.1.36
Maximum number of drives that can be spin up in an enclosure
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

spinupEnclDelay 1.3.6.1.4.1.3582.4.1.4.1.2.1.37
Delay between drive spin up for drives within an enclosure
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

defaultLdPSPolicy 1.3.6.1.4.1.3582.4.1.4.1.2.1.38
power saving policy.values:controller default power saving policy=0, AUTO=1, MAX=2, Max with no cache=6, NONE=255
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

disableLdPSInterval 1.3.6.1.4.1.3582.4.1.4.1.2.1.39
LD power savings are disabled for yy hours beginning at disableLdPSTime.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

disableLdPSTime 1.3.6.1.4.1.3582.4.1.4.1.2.1.40
LD power savings shall be disabled at xx minutes from 12:00am.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

supportBreakMirror 1.3.6.1.4.1.3582.4.1.4.1.2.1.41
1=Support break mirror operation,0=Do not Support break mirror operation
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

temperatureROC 1.3.6.1.4.1.3582.4.1.4.1.2.1.42
temperature of RAID On Chip in Celsius
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

temperatureCtrl 1.3.6.1.4.1.3582.4.1.4.1.2.1.43
temperature of controller in Celsius
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

preventPIImport 1.3.6.1.4.1.3582.4.1.4.1.2.1.44
1=Prevent import of SAS PI protected logical disks , 0=Not Prevent import of SAS PI protected logical disks
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

enablePI 1.3.6.1.4.1.3582.4.1.4.1.2.1.45
1 = Enable SAS PI for controller , 0 = Disable SAS PI for controller
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

totalSpaceformetadata 1.3.6.1.4.1.3582.4.1.4.1.2.1.46
Total Space used for MetaData
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

useEmergencySpare 1.3.6.1.4.1.3582.4.1.4.1.2.1.47
This field give the information about Emergency Spare possible Drive types(Uncongiured Good/Global Hotspare)
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

useEmergencySparesforSMARTer 1.3.6.1.4.1.3582.4.1.4.1.2.1.48
1 = Use Emergency spares for SMARTer ,0 = Not Use Emergency spares for SMARTer
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

supportShieldState 1.3.6.1.4.1.3582.4.1.4.1.2.1.49
1 =Support PD shield state ,0 = Not Support PD shield state
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

writeCacheCapable 1.3.6.1.4.1.3582.4.1.4.1.2.1.50
1 = SSC support write caching IOs ,0 = SSC not support write caching IOs
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

totalCacheSize 1.3.6.1.4.1.3582.4.1.4.1.2.1.51
This field give the information about total Size of currently configured SSC,in GB
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

maximumCacheSize 1.3.6.1.4.1.3582.4.1.4.1.2.1.52
This field give the information about maxmium Size of SSC that can yet be configured,in GB
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

ctrlSasAddr 1.3.6.1.4.1.3582.4.1.4.1.2.1.53
This field gives the controller SAS address
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

domainId 1.3.6.1.4.1.3582.4.1.4.1.2.1.54
This field gives the Domain ID
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

peerControllerStatus 1.3.6.1.4.1.3582.4.1.4.1.2.1.55
This field gives the Peer controller Status
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

maximumControllerNodes 1.3.6.1.4.1.3582.4.1.4.1.2.1.56
This field gives the HA nodes this FW supports
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

incompatibilityDetails 1.3.6.1.4.1.3582.4.1.4.1.2.1.57
This field gives the Incompatibility Details
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

topologyType 1.3.6.1.4.1.3582.4.1.4.1.2.1.58
This field gives the Topology Type
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

supportOnlineFWUpdate 1.3.6.1.4.1.3582.4.1.4.1.2.1.59
1 = Online firmware update is supported, 0 = Online firmware update is not supported
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

adapterInfoTable 1.3.6.1.4.1.3582.4.1.4.1.3
A List of adapter Entries containing Information/Properties about the adapters on the Controller.
Status: optional Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdapterInfoEntry

adapterInfoEntry 1.3.6.1.4.1.3582.4.1.4.1.3.1
An Entry in the adapterInfo table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdapterInfoEntry  

adapterID-AIT 1.3.6.1.4.1.3582.4.1.4.1.3.1.1
AdapterID for this Adapter.(Unique)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

adapterVendorID 1.3.6.1.4.1.3582.4.1.4.1.3.1.2
PCI Vendor ID for this Adapter.
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

devID 1.3.6.1.4.1.3582.4.1.4.1.3.1.3
PCI Device ID for this Adapter.
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

subVendorID 1.3.6.1.4.1.3582.4.1.4.1.3.1.4
PCI Sub-Vendor ID for this adapter.
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

subDevID 1.3.6.1.4.1.3582.4.1.4.1.3.1.5
PCI Sub-Device ID for this adapter.
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

hostInterface 1.3.6.1.4.1.3582.4.1.4.1.3.1.6
Host interface information for this adapter. Values: N/A(0),PCIX(1),PCIE(2),iSCSI(3),SAS-3G(4)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

hostInterfacePortCnt 1.3.6.1.4.1.3582.4.1.4.1.3.1.7
Port Count on this adapter.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

hostInterfacePortAddr 1.3.6.1.4.1.3582.4.1.4.1.3.1.8
Port address comma delimited
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

devInterface 1.3.6.1.4.1.3582.4.1.4.1.3.1.9
Multiple device interface support values separated by space.
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

devInterfacePortCnt 1.3.6.1.4.1.3582.4.1.4.1.3.1.10
Device Port Count on this adapter.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

devInterfacePortAddr 1.3.6.1.4.1.3582.4.1.4.1.3.1.11
Device Port address comma delimited
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

productName 1.3.6.1.4.1.3582.4.1.4.1.3.1.12
Product name e.g. MegaRAID SAS-8E, MegaRAID SAS-4X, etc.
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

serialNo 1.3.6.1.4.1.3582.4.1.4.1.3.1.13
Controller serial number
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

firmwareVersion 1.3.6.1.4.1.3582.4.1.4.1.3.1.14
Firmware version Format->(Firmware Package Version:Version:Date:Time)
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

driverVersion 1.3.6.1.4.1.3582.4.1.4.1.3.1.15
Driver version Format->(Driver Name:Version)
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

expanderFirmwareVersion 1.3.6.1.4.1.3582.4.1.4.1.3.1.16
Expander firmware version - Not Available if expander is not present on the controller
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

lockKeyBinding 1.3.6.1.4.1.3582.4.1.4.1.3.1.17
Type of lock key binding. lock key is not bound(0),lock key bound to FW secret key(1), lock key bound to user(2), lock key bound to a TPM(3)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

maxDAPdCountSpinup60 1.3.6.1.4.1.3582.4.1.4.1.3.1.18
Maximum number of drives to spinup within 60 sec for direct attached drives
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

adapterSupportInfoTable 1.3.6.1.4.1.3582.4.1.4.1.4
A List of adapter Entries containing Information/Properties about the adapters on the Controller.
Status: optional Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdapterSupportInfoEntry

adapterSupportInfoEntry 1.3.6.1.4.1.3582.4.1.4.1.4.1
An Entry in the adapter table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdapterSupportInfoEntry  

adapterID-ASIT 1.3.6.1.4.1.3582.4.1.4.1.4.1.1
AdapterID for this Adapter.(Unique)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

maxArms 1.3.6.1.4.1.3582.4.1.4.1.4.1.2
Maximum arms per Virtual Drive supported for this Adapter.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

maxSpans 1.3.6.1.4.1.3582.4.1.4.1.4.1.3
Maximum spans per Virtual Drive supported for this Adapter.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

maxArrays 1.3.6.1.4.1.3582.4.1.4.1.4.1.4
Maximum no of arrays supported for this adapter.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

maxVDs 1.3.6.1.4.1.3582.4.1.4.1.4.1.5
Maximum number of Virtual Drive s supported for this adapter.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

hardwarePresent 1.3.6.1.4.1.3582.4.1.4.1.4.1.6
Supported Hardware on this adapter. bbu(1),alarm(2),nvram(3),uart(4),TPM(5),expander(6). For multiple hw support a space delimited list will appear.
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

maxConcurrentCmds 1.3.6.1.4.1.3582.4.1.4.1.4.1.7
The maximum parallel commands supported on this adapter.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

maxSGECount 1.3.6.1.4.1.3582.4.1.4.1.4.1.8
The maximum Scatter Gather Element count allowed on this adapter.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

maxRequestSize 1.3.6.1.4.1.3582.4.1.4.1.4.1.9
The maximum data transfer size in sectors, on this adapter.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

maxLdsPerArray 1.3.6.1.4.1.3582.4.1.4.1.4.1.10
Max Ld's per array in adapter
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

partitionsInDDF 1.3.6.1.4.1.3582.4.1.4.1.4.1.11
Max LD's per Array in configuration
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

allowSSDMixInLD 1.3.6.1.4.1.3582.4.1.4.1.4.1.12
allow SAS/SATA SSD mix within an LD. allow(1), not allow(0)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

allowMixSSDHDDInLD 1.3.6.1.4.1.3582.4.1.4.1.4.1.13
allow SSD/HDD mix within an LD.allow(1), not allow(0)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adapterOperationsSupportInfoTable 1.3.6.1.4.1.3582.4.1.4.1.5
A List of adapter Entries containing Information/Properties about the adapters on the Controller.
Status: optional Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdapterOperationsSupportInfoEntry

adapterOperationsSupportInfoEntry 1.3.6.1.4.1.3582.4.1.4.1.5.1
An Entry in the adapter table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdapterOperationsSupportInfoEntry  

adapterID 1.3.6.1.4.1.3582.4.1.4.1.5.1.1
AdapterID for this Adapter.(Unique)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

rbldRateSupported 1.3.6.1.4.1.3582.4.1.4.1.5.1.2
Rebuilding rate change support for this Adapter. Values: false(0),true(1)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

ccRateSupported 1.3.6.1.4.1.3582.4.1.4.1.5.1.3
Consistency Check rate change support for this Adapter. Values: false(0),true(1)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

bgiRateSupported 1.3.6.1.4.1.3582.4.1.4.1.5.1.4
Background initialization rate change support for this adapter. Values: false(0),true(1)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

reconRateSupported 1.3.6.1.4.1.3582.4.1.4.1.5.1.5
Reconstruction rate change support for this adapter. Values: false(0),true(1)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

patrolRateSupported 1.3.6.1.4.1.3582.4.1.4.1.5.1.6
Patrol read rate change support for this adapter. Values: false(0),true(1)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

alarmControlSupported 1.3.6.1.4.1.3582.4.1.4.1.5.1.7
Alarm control support for this adapter. Values: false(0),true(1)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

clusterSupported 1.3.6.1.4.1.3582.4.1.4.1.5.1.8
Cluster support for this adapter. Values: false(0),true(1)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

bbuSupported 1.3.6.1.4.1.3582.4.1.4.1.5.1.9
BBU support for this adapter. Values: false(0),true(1)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

spanningAllowedSupported 1.3.6.1.4.1.3582.4.1.4.1.5.1.10
Spanning support for this adapter. Values: false(0),true(1)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

dedicatedHotSparesSupported 1.3.6.1.4.1.3582.4.1.4.1.5.1.11
Dedicated HotSpares support for this adapter. Values: false(0),true(1)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

revertibleHotSparesSupported 1.3.6.1.4.1.3582.4.1.4.1.5.1.12
Revertible HotSpares support for this adapter. Values: false(0),true(1)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

foreignConfigImportSupported 1.3.6.1.4.1.3582.4.1.4.1.5.1.13
Support foreign config import on this adapter. Values: false(0),true(1)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

selfDiagnosticSupported 1.3.6.1.4.1.3582.4.1.4.1.5.1.14
Controller supports self diagnostic. Values: false(0),true(1)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

allowMixedRedundancyOnArraySupported 1.3.6.1.4.1.3582.4.1.4.1.5.1.15
Allow different Virtual Disk on the same array to have different redundancy levels. Values: false(0),true(1)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

abortCConErrorSupported 1.3.6.1.4.1.3582.4.1.4.1.5.1.16
Abort CC on detecting error is supported on this adapter. Values: No(0),Yes(1)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

securitySupported 1.3.6.1.4.1.3582.4.1.4.1.5.1.17
Displays the security support. if supported (1) , not supported (0)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

supportPIcontroller 1.3.6.1.4.1.3582.4.1.4.1.5.1.18
Displays the support PI. 1=LD SAS PI Type 0, 0=LD Not SAS PI Type 0
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

bbuInfo 1.3.6.1.4.1.3582.4.1.4.1.6
OBJECT IDENTIFIER    

bbuNumber 1.3.6.1.4.1.3582.4.1.4.1.6.1
The present number of rows in the BBU Table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

bbuTable 1.3.6.1.4.1.3582.4.1.4.1.6.2
A List of BBU Entries containing Information/Properties about the BBU.
Status: optional Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BBUEntry

bbuEntry 1.3.6.1.4.1.3582.4.1.4.1.6.2.1
An Entry in the BBU table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  BBUEntry  

bbuID 1.3.6.1.4.1.3582.4.1.4.1.6.2.1.1
BBUID for this BBU.(Unique)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

batteryType 1.3.6.1.4.1.3582.4.1.4.1.6.2.1.2
BBU Type.
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

nextLearnTime 1.3.6.1.4.1.3582.4.1.4.1.6.2.1.3
Time of next scheduled learn cycle (seconds past 1/1/2000)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

absStateOfCharge 1.3.6.1.4.1.3582.4.1.4.1.6.2.1.4
Predicted remaining capacity expressed as % of DesignCapacity() (0-100). Value of -1 means not supported
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

fullChargeCapacity 1.3.6.1.4.1.3582.4.1.4.1.6.2.1.5
Predicted pack capacity when it is fully charged in joules
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

averageEmptyTime 1.3.6.1.4.1.3582.4.1.4.1.6.2.1.6
One-minute rolling average of the predicted remaining battery life. Value of -1 means not supported
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

cycleCount 1.3.6.1.4.1.3582.4.1.4.1.6.2.1.7
Number of charge cycles the battery has experienced. Value of -1 means not supported
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

firmwareStatus 1.3.6.1.4.1.3582.4.1.4.1.6.2.1.8
Condition of battery in following order: packMissing(0/1) voltageLow(0/1) temperatureHigh(0/1) chargeActive(0/1) dischargeActive(0/1) learnCycleRequested(0/1) learnCycleActive(0/1) learnCycleFailed(0/1) learnCycleTimeout(0/1) i2cErrorsDetected(0/1) noSpace(0/1) predictiveFailure(0/1) premiumFeatureReqd(0/1) microcodeUpdateReqd(0/1) Only enabled(1) values will be shown
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

voltage 1.3.6.1.4.1.3582.4.1.4.1.6.2.1.9
Accurate battery terminal voltage in mV, resolution of 1mV
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

autoLearnPeriod 1.3.6.1.4.1.3582.4.1.4.1.6.2.1.10
Time (in seconds) between learn cycles (0 to disable auto learn)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

relStateOfCharge 1.3.6.1.4.1.3582.4.1.4.1.6.2.1.11
Predicted remaining capacity expressed as % of FullChargeCapacity() (0-100). Value of -1 means not supported
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

capacityRemain 1.3.6.1.4.1.3582.4.1.4.1.6.2.1.12
Predicted charge or energy remaining in the battery in joules
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

runTimeToEmpty 1.3.6.1.4.1.3582.4.1.4.1.6.2.1.13
Relative gain or loss in remaining life in response to change in power policy represent in minute. Value of -1 means not supported
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

avgTimeToFull 1.3.6.1.4.1.3582.4.1.4.1.6.2.1.14
One-minute rolling average of predicted remaining time to full charge. Value of -1 means not supported
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

errorMargin 1.3.6.1.4.1.3582.4.1.4.1.6.2.1.15
Expected margin of error (%) in charge calculation (2-100). Value of -1 means not supported
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER 2..100  

temperature 1.3.6.1.4.1.3582.4.1.4.1.6.2.1.16
Battery temperature in degree Centigrade
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

mfgName 1.3.6.1.4.1.3582.4.1.4.1.6.2.1.17
Battery manufacturer's name
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

deviceName 1.3.6.1.4.1.3582.4.1.4.1.6.2.1.18
Battery name
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

serialNumber 1.3.6.1.4.1.3582.4.1.4.1.6.2.1.19
Battery serialNumber
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

chargerStatus 1.3.6.1.4.1.3582.4.1.4.1.6.2.1.20
Battery charger status. Values: N/A(-1), off(0), complete(1), progress(2)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

adpID 1.3.6.1.4.1.3582.4.1.4.1.6.2.1.21
The adapter id where BBU is attached
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

remainingCapAlarm 1.3.6.1.4.1.3582.4.1.4.1.6.2.1.22
Remaining capacity to alarm. Value of -1 means not supported
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

remainingTimeAlarm 1.3.6.1.4.1.3582.4.1.4.1.6.2.1.23
Remaining time to alarm. Value of -1 means not supported
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

bbu-current 1.3.6.1.4.1.3582.4.1.4.1.6.2.1.24
Current(In mA) being supplied (or accepted) through the battery terminals
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

gasGaugeStatus 1.3.6.1.4.1.3582.4.1.4.1.6.2.1.25
Gas gauge status
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

bbuFRU 1.3.6.1.4.1.3582.4.1.4.1.6.2.1.26
bbu FRU
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

batteryReplacement 1.3.6.1.4.1.3582.4.1.4.1.6.2.1.27
This property denotes whether the Battery needs to be replaced or not.1 =battery needs to be replaced ,0 =battery needs not to be replaced
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

bbuRetentiontime 1.3.6.1.4.1.3582.4.1.4.1.6.2.1.28
The total no. of hours the battery can support the current capacity reserve. Undefined(0),48 hours+(>48),the exact no of hours(<=48)
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

bbuState 1.3.6.1.4.1.3582.4.1.4.1.6.2.1.29
This property gives the Information about BBU state. Operational = if BBU is working fine, Non-Operational = if BBU is not working fine
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

memoryModuleFRU 1.3.6.1.4.1.3582.4.1.4.1.6.2.1.30
tmm FRU
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

bbuFirmwareVersion 1.3.6.1.4.1.3582.4.1.4.1.6.2.1.31
Battery Firmware Version
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

adapterStatusSupportInfoTable 1.3.6.1.4.1.3582.4.1.4.1.9
A List of adapter Entries containing Information/Properties about the adapters on the Controller.
Status: optional Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdapterStatusSupportInfoEntry

adapterStatusSupportInfoEntry 1.3.6.1.4.1.3582.4.1.4.1.9.1
An Entry in the adapter table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdapterStatusSupportInfoEntry  

adapterID-ASSIT 1.3.6.1.4.1.3582.4.1.4.1.9.1.1
AdapterID for this Adapter.(Unique)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

lockKeyAssigned 1.3.6.1.4.1.3582.4.1.4.1.9.1.2
Lock key Assigned support for this Adapter. Values: false(0),true(1)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

lockKeyFailed 1.3.6.1.4.1.3582.4.1.4.1.9.1.3
lock Key Failed support for this Adapter. Values: false(0),true(1)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

lockKeyNotBackedup 1.3.6.1.4.1.3582.4.1.4.1.9.1.4
lock Key Not Backedup support for this Adapter. Values: false(0),true(1)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

biosNotDetected 1.3.6.1.4.1.3582.4.1.4.1.9.1.5
bios Not Detected support for this Adapter. Values: false(0),true(1)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

cacheIsPinned 1.3.6.1.4.1.3582.4.1.4.1.9.1.6
1=controller cache is pinned for missing or offline LDs
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

adapterLdOperationSupportInfoTable 1.3.6.1.4.1.3582.4.1.4.1.10
A List of adapter Entries containing Information/Properties about the adapters on the Controller.
Status: optional Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdapterLdOperationSupportInfoEntry

adapterLdOperationSupportInfoEntry 1.3.6.1.4.1.3582.4.1.4.1.10.1
An Entry in the adapter table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdapterLdOperationSupportInfoEntry  

adapterID-ALSIT 1.3.6.1.4.1.3582.4.1.4.1.10.1.1
AdapterID for this Adapter.(Unique)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

allowCtrlEncryption 1.3.6.1.4.1.3582.4.1.4.1.10.1.2
if it is set (1) supports controller encryption
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

device 1.3.6.1.4.1.3582.4.1.4.2
OBJECT IDENTIFIER    

physicalDriveInfo 1.3.6.1.4.1.3582.4.1.4.2.1
OBJECT IDENTIFIER    

commonDeviceInfoTable 1.3.6.1.4.1.3582.4.1.4.1.7
A List of general Physical Disk info
Status: optional Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CommonDeviceInfoEntry

commonDeviceInfoEntry 1.3.6.1.4.1.3582.4.1.4.1.7.1
An Entry in the CommonDeviceInfo table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CommonDeviceInfoEntry  

adapterID-CDIT 1.3.6.1.4.1.3582.4.1.4.1.7.1.1
Unique adapter ID
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

forceOnline 1.3.6.1.4.1.3582.4.1.4.1.7.1.2
Physical drive force Online operation support. Values: notSupported(0), supported(1)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

forceOffline 1.3.6.1.4.1.3582.4.1.4.1.7.1.3
Physical drive force Offline operation support. Values: notSupported(0), supported(1)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

forceRebuild 1.3.6.1.4.1.3582.4.1.4.1.7.1.4
Physical drive force Rebuild operation support. Values: notSupported(0), supported(1)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

supportsSAS 1.3.6.1.4.1.3582.4.1.4.1.7.1.5
SAS physical drive support. Values: notSupported(0), supported(1)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

supportsSATA 1.3.6.1.4.1.3582.4.1.4.1.7.1.6
SATA physical drive support. Values: notSupported(0), supported(1)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

allowMixInEnclosure 1.3.6.1.4.1.3582.4.1.4.1.7.1.7
Mix InEnclosure support. Values: notSupported(0), supported(1)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

allowMixInVD 1.3.6.1.4.1.3582.4.1.4.1.7.1.8
MixInVIRTUALDRIVE support. Values: notSupported(0), supported(1)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

allowSataInCluster 1.3.6.1.4.1.3582.4.1.4.1.7.1.9
SataInCluster support. Values: notSupported(0), supported(1)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

setPowerStateForCfg 1.3.6.1.4.1.3582.4.1.4.1.7.1.10
FW requires application to set power state before configuration changes. Required(1), Not Required(0)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pdNumber 1.3.6.1.4.1.3582.4.1.4.2.1.1
The present number of rows in the physical drive table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

physicalDriveTable 1.3.6.1.4.1.3582.4.1.4.2.1.2
A List of physical drive Entries containing Information/Properties about the drives
Status: optional Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PhysicalDriveEntry

physicalDriveEntry 1.3.6.1.4.1.3582.4.1.4.2.1.2.1
An Entry in the Device Table.
Status: optional Access: not-accessible
OBJECT-TYPE    
  PhysicalDriveEntry  

pdIndex 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.1
The unique ID
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

physDevID 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.2
The Device ID
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

oemSupported 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.3
Is the drive supported by the OEM (OEM-specific checks). Values: notSupported(1), supported(0)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

scsiDevType 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.4
Type of this Device. Values: disk(0),tape(1),printer(2),processor(3),cdrom(5),scanner(6),optical(7),enclosure(13),dvd(10),unknown(31)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

connectedAdapterPort 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.5
Adapter port(s) to which the device is connected.
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

deviceSpeed 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.6
Maximum supported speed. Values: speed-unknown(0),speed-1p5G(1),speed-3G(2),speed-6G(3)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

mediaErrCount 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.7
Error count of the device
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

otherErrCount 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.8
Other error count of the device
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

predFailCount 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.9
Predictive fail count of the device
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

pdState 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.10
Firmware's interpretation of drive state. Values: unconfigured-good(0),unconfigured-bad(1),hot-spare(2),offline(16),failed(17),rebuild(20),online(24),copyback(32),system(64),UNCONFIGURED-SHIELDED(128),HOTSPARE-SHIELDED(130),CONFIGURED-SHIELDED(144)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

disabledForRemoval 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.11
If true, drive is ready for removal. Values: false(0),true(1)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

linkSpeed 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.12
Negotiated link speed. Values: speed-unknown(0),speed-1p5G(1),speed-3G(2),speed-6G(3)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

pdSupportFlags 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.13
1st Byte:forcedPDGUID(0/1),2nd Byte:inVD(0/1),3rd Byte:isGlobalSpare(0/1),4th Byte:isSpare(0/1),5th Byte:isForeign(0/1),6th Byte:intf(0-Unknown, 1-parallel SCSI, 2-SAS, 3-SATA, 4-FC).A comma delimited list will appear.
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

sasAddr 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.14
Device SAS addresses. Comma separeted for multiple address
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

rawSize 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.15
Size(MB) before COD and coercion
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

nonCoercedSize 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.16
Size(MB) after COD is reserved but before coercion
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

coercedSize 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.17
Size(MB) after COD is reserved and after coercion
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

enclDeviceId 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.18
Enclosure's device Id (in decimal); if device is not within enclosure value is -1
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

enclIndex 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.19
Firmware internal enclosure index
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

slotNumber 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.20
Slot number of this drive, if the Physical Disk is part of an enclosure then -1
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

operationProgress 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.21
Operation progress in %. e.g. Rebuild progress is 10%
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

adpID-PDT 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.22
Controller id where this Physical Drive is attached
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

operationSupport 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.23
MakeOnline,MakeOffline,MakeFailed,MakeBad,MakeUncofigured, MakeSpare,RemoveSpare,replaceMissing,markMissing,startRebuild, stopRebuild,locate,pdclear,foreignImportNotAllowed,ForeignImportAllowed, startCopyBack,stopCopyBack,fwDownloadNotAllowed,fwDownloadAllowed,makeSystem
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

pdVendorID 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.24
Vendor ID
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

pdProductID 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.25
Product ID
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

pdFwversion 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.26
PD firmware version
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

diskType 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.27
Type of the disk : 0-Unknown, 1-parallel SCSI, 2-SAS, 3-SATA, 4-FC
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

partnerDevId 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.28
If drive is in an enclosure with dual paths,This is Partner Device ID. In all other cases INVALID(-1)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

mediatype 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.29
Media Type HDD(0),SSD(1),Solid state flash module(2)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

powerState 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.30
Power condition of the device. Values are device is active(0),device is stopped(1),device is transitioning between power states(255)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

secured 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.31
1=drive is secured, 0=not secured
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

locked 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.32
1=drive is locked, 0=unlocked
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

foreign 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.33
1=drive is secured by a foreign lock key, 0=drive is not secured by a foreign lock key
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

oemCertified 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.34
Is the drive certified by the OEM (OEM-specific checks). Values: notCertified(1), Certified(0)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

foreignImportNotAllowed 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.35
1=Drive is not allowed foreignImport operation, 0=Drive is allowed foreignImport operation
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

pdTemperature 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.36
Physical Drive temperature in Celsius
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

pdSerialNumber 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.37
Physical Drives serial number
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

piEligible 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.38
Protection Information eligibility.1=drive can be used for PD Enabled LD , 0=drive can't be used for PD Enabled LD
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

piType 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.39
SAS Protection Information Type .No SAS protection type used(0) ,SAS PI Type 1(1) ,SAS PI Type 2(2) ,SAS PI Type 3(3) ,Reserved SAS PI Type 4(4) ,Reserved SAS PI Type 5(5) ,Reserved SAS PI Type 6(6) ,Reserved SAS PI Type 7(7).
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

piFormatted 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.40
formatted for PI information. 1=drive is formatted for PI information, 0=no PI data.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

userDataBlockSize 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.41
Number of bytes of user data in LBA
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

commissionedSpare 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.42
Yes = this PD is a commissioned spare, No = this PD is not a commissioned spare.
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

emergencySpare 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.43
Eligible = this PD is a emergency spare, Ineligible = this PD is not a emergency spare.
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

shieldCounter 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.44
How many times the shield diagnostics was run before it was marked failed
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

shieldDiagCompletionTime 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.45
Last successful Diagnostics completion time. 0 is N/A
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

ineligibleForSSCD 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.46
Whether PD cannot be used for an SSCD. PD can not be used for an SSCD(1), PD can be used for an SSCD(0)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

ineligibleForLd 1.3.6.1.4.1.3582.4.1.4.2.1.2.1.47
Whether PD cannot be used for a regular LD. PD can not be used for a regular LD(1), PD can be used for a regular LD(0)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

virtualDevice 1.3.6.1.4.1.3582.4.1.4.3
OBJECT IDENTIFIER    

commonVirtualDeviceInfoTable 1.3.6.1.4.1.3582.4.1.4.1.8
A List of general Virtual Drive info
Status: optional Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CommonVirtualDeviceInfoEntry

commonVirtualDeviceInfoEntry 1.3.6.1.4.1.3582.4.1.4.1.8.1
An Entry in the CommonVirtualDeviceInfo table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CommonVirtualDeviceInfoEntry  

adapterID-CVDIT 1.3.6.1.4.1.3582.4.1.4.1.8.1.1
Unique adapter ID
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

supportedReadPolicy 1.3.6.1.4.1.3582.4.1.4.1.8.1.2
Read policy support. Values: false(0),true(1)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

supportedWritePolicy 1.3.6.1.4.1.3582.4.1.4.1.8.1.3
Write policy support. Values: false(0),true(1)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

supportedIOPolicy 1.3.6.1.4.1.3582.4.1.4.1.8.1.4
IO policy support. Values: false(0),true(1)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

supportedAccessPolicy 1.3.6.1.4.1.3582.4.1.4.1.8.1.5
Access policy support. Values: false(0),true(1)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

supportedMinSize 1.3.6.1.4.1.3582.4.1.4.1.8.1.6
Minimum stripe size supported. 0(512B),1(1K),2(2K),3(4K),4(8K),5(16K),6(32),7(64K),8(128K) ... 11(1MB) etc
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

supportedMaxSize 1.3.6.1.4.1.3582.4.1.4.1.8.1.7
Maximum stripe size supported. 0(512B),1(1K),2(2K),3(4K),4(8K),5(16K),6(32),7(64K),8(128K) ... 11(1MB) etc
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ldbbm 1.3.6.1.4.1.3582.4.1.4.1.8.1.8
1=LD bad block management is enabled, 0=LD bad block management is not enabled
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

vdInfo 1.3.6.1.4.1.3582.4.1.4.3.1
OBJECT IDENTIFIER    

vdNumbers 1.3.6.1.4.1.3582.4.1.4.3.1.1
The present number of rows in the virtualDrive table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

virtualDriveTable 1.3.6.1.4.1.3582.4.1.4.3.1.2
A List of Virtual Drives Entries containing Information/Properties about the virtualDrive.
Status: optional Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VirtualDriveEntry

virtualDriveEntry 1.3.6.1.4.1.3582.4.1.4.3.1.2.1
An Entry in the virtualDrive Table.
Status: optional Access: not-accessible
OBJECT-TYPE    
  VirtualDriveEntry  

virtualDevID 1.3.6.1.4.1.3582.4.1.4.3.1.2.1.1
The unique Virtual Drives ID
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

size 1.3.6.1.4.1.3582.4.1.4.3.1.2.1.2
Total size in MB of the drive
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

clusterOwnerDeviceId 1.3.6.1.4.1.3582.4.1.4.3.1.2.1.3
VD owner's device Id
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

targetId 1.3.6.1.4.1.3582.4.1.4.3.1.2.1.4
Virtual Drive target id (i.e. 0 to 63)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

state 1.3.6.1.4.1.3582.4.1.4.3.1.2.1.5
The Device state: Values: offline(0),partially-degraded(1),degraded(2),optimal(3)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

name 1.3.6.1.4.1.3582.4.1.4.3.1.2.1.6
Virtual Drive name
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

defaultCachePolicy 1.3.6.1.4.1.3582.4.1.4.3.1.2.1.7
Default cache policy settings. Values: WriteBack, WriteThrough, ReadAdaptive, ReadAhead, ReadAheadNone, Cached, Direct, Write Cache OK if Bad BBU, No Write Cache if Bad BBU.
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

accessPolicy 1.3.6.1.4.1.3582.4.1.4.3.1.2.1.8
Access policy settings. Values: access-rw(0), access-read-only(2), access-blocked(3)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

diskCachePolicy 1.3.6.1.4.1.3582.4.1.4.3.1.2.1.9
Physical disk cache policy. Values: unchanged(0),enable(1),disable(2)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

bgiState 1.3.6.1.4.1.3582.4.1.4.3.1.2.1.10
Disable/Enable Back Groung Initialization on this Virtual Drive. Values: disable(1),enable(0)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

prl 1.3.6.1.4.1.3582.4.1.4.3.1.2.1.11
Primay raid level. Values: 0(RAID-0), 1(RAID-1), 3(RAID-3), 4(RAID-4), 5(RAID-5), 6(RAID-6),15(Single Disk or JBOD), 17(RAID-1E), 21(RAID-5E), 31(Concatenation),37(RAID-5EEE)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

rLQ 1.3.6.1.4.1.3582.4.1.4.3.1.2.1.12
Raid level qualifier
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

sRL 1.3.6.1.4.1.3582.4.1.4.3.1.2.1.13
Secondary raid level. Values: 0(Stripped), 1(Mirrored), 2(Concatenated), 3(Spanned)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

stripeSize 1.3.6.1.4.1.3582.4.1.4.3.1.2.1.14
Stripe Size. 0(512B),1(1K),2(2K),3(4K),4(8K),5(16K),6(32),7(64K),8(128K) ... 11(1MB) etc
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

numDrives 1.3.6.1.4.1.3582.4.1.4.3.1.2.1.15
Number of drivers per span
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

spanDepth 1.3.6.1.4.1.3582.4.1.4.3.1.2.1.16
Number of spans. If only one array then it is considered as 1 span
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

initState 1.3.6.1.4.1.3582.4.1.4.3.1.2.1.17
0=no init, 1=quick init, 2=full init
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

vdOperationProgress 1.3.6.1.4.1.3582.4.1.4.3.1.2.1.18
Progress % for an operation / No operation in progress
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

currentCachePolicy 1.3.6.1.4.1.3582.4.1.4.3.1.2.1.19
Cache policy settings. Values:WriteBack, WriteThrough, ReadAdaptive, ReadAhead, ReadAheadNone, Cached, Direct, Write Cache OK if Bad BBU, No Write Cache if Bad BBU.
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

adapterID-VDT 1.3.6.1.4.1.3582.4.1.4.3.1.2.1.20
Adapter ID
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

encryptionType 1.3.6.1.4.1.3582.4.1.4.3.1.2.1.21
logical drive encryption type. Values No Encryption(0), FDE drive encryption(1), Controller-based encryption(2)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

vdOperationSupport 1.3.6.1.4.1.3582.4.1.4.3.1.2.1.22
startFGI,stopFGI,startCC,stopCC,startRecon,deleteLD
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

badBlocksExist 1.3.6.1.4.1.3582.4.1.4.3.1.2.1.23
0 = LD bad block table is empty, 1 = LD bad block table is not empty
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

defaultPSPolicy 1.3.6.1.4.1.3582.4.1.4.3.1.2.1.24
Power Savings policy set for this LD.Values:controller default power saving policy=0, AUTO=1, MAX=2, MAX with no cache=6, NONE=255
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

currentPSPolicy 1.3.6.1.4.1.3582.4.1.4.3.1.2.1.25
Power Savings policy set for this LD.Values:controller default power saving policy=0, AUTO=1, MAX=2, MAX with no cache=6, NONE=255
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

breakMirror 1.3.6.1.4.1.3582.4.1.4.3.1.2.1.26
Break Mirror Policy set for this LD.Values:1=break mirror is allowed, 0=break mirror not is allowed
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

joinMirror 1.3.6.1.4.1.3582.4.1.4.3.1.2.1.27
Join Mirror policy set for this LD.Values:1=join mirror is allowed, 0=join mirror not is allowed
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

mirrorPdInfo 1.3.6.1.4.1.3582.4.1.4.3.1.2.1.28
Mirror Info Property give the Information about mirror of PD and PD state respectively.
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

vdPiType 1.3.6.1.4.1.3582.4.1.4.3.1.2.1.29
Information about logical drive protection type . No SAS protection type used(0) ,SAS PI Type 1(1) ,SAS PI Type 2(2) ,SAS PI Type 3(3) ,Reserved SAS PI Type 4(4) ,Reserved SAS PI Type 5(5) ,Reserved SAS PI Type 6(6) ,Reserved SAS PI Type 7(7) ,SAS PI Type 8(8).
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

mirrorDataSize 1.3.6.1.4.1.3582.4.1.4.3.1.2.1.30
Total Space used for mirrorData or Parity information
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

cacheCadeType 1.3.6.1.4.1.3582.4.1.4.3.1.2.1.31
0= Non-CacheCade VD, 1= CacheCade Type is Read & Write, 2= CacheCade Type is Read only, 3= R1-EC
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

currentWritePolicy 1.3.6.1.4.1.3582.4.1.4.3.1.2.1.32
Current write policy settings. Values: WriteBack, WriteThrough, AlwaysWriteBack
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

defaultWritePolicy 1.3.6.1.4.1.3582.4.1.4.3.1.2.1.33
Default write policy settings. Values: WriteBack, WriteThrough, AlwaysWriteBack
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

associatedVD 1.3.6.1.4.1.3582.4.1.4.3.1.2.1.34
This property gives the Information about VD is Cached or VD is not cached.
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

hostAccessPolicy 1.3.6.1.4.1.3582.4.1.4.3.1.2.1.35
This property gives the Host Access Policy
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

guid 1.3.6.1.4.1.3582.4.1.4.3.1.2.1.36
This property gives the LD GUID.
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

vdSpanInfoTable 1.3.6.1.4.1.3582.4.1.4.3.1.3
A List of span Entries containing Information/Properties vd span.
Status: optional Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VDSpanInfoEntry

vdSpanInfoEntry 1.3.6.1.4.1.3582.4.1.4.3.1.3.1
An Entry in the vdSpan Table.
Status: optional Access: not-accessible
OBJECT-TYPE    
  VDSpanInfoEntry  

spanID 1.3.6.1.4.1.3582.4.1.4.3.1.3.1.1
The unique Span ID
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

vdID-VSIT 1.3.6.1.4.1.3582.4.1.4.3.1.3.1.2
The Virtual Device ID
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

startBlock 1.3.6.1.4.1.3582.4.1.4.3.1.3.1.3
Span physical disk starting block
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

numBlocks 1.3.6.1.4.1.3582.4.1.4.3.1.3.1.4
Span physical disk block count
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

vdSpanArrayRef 1.3.6.1.4.1.3582.4.1.4.3.1.3.1.5
Array reference (index)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

adapterID-VSIT 1.3.6.1.4.1.3582.4.1.4.3.1.3.1.6
Adapter ID
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

arrayInfo 1.3.6.1.4.1.3582.4.1.4.3.4
OBJECT IDENTIFIER    

arrayNumber 1.3.6.1.4.1.3582.4.1.4.3.4.1
The present number of rows in the array table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

arrayTable 1.3.6.1.4.1.3582.4.1.4.3.4.2
A List of array Entries containing Information/Properties about the arrays.
Status: optional Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ArrayEntry

arrayEntry 1.3.6.1.4.1.3582.4.1.4.3.4.2.1
An Entry in the array Table.
Status: optional Access: not-accessible
OBJECT-TYPE    
  ArrayEntry  

arrayID 1.3.6.1.4.1.3582.4.1.4.3.4.2.1.1
The unique array ID
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

arraySize 1.3.6.1.4.1.3582.4.1.4.3.4.2.1.2
Size in MB
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

arrayNumDrives 1.3.6.1.4.1.3582.4.1.4.3.4.2.1.3
Number of drives for this array
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

arrayRef 1.3.6.1.4.1.3582.4.1.4.3.4.2.1.4
Tag for the array
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

pdList 1.3.6.1.4.1.3582.4.1.4.3.4.2.1.5
Space separated Physical Drive identification. e.g. {devID devID devID} etc
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

adapterID-AT 1.3.6.1.4.1.3582.4.1.4.3.4.2.1.6
Adapter ID.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

spareInfo 1.3.6.1.4.1.3582.4.1.4.3.5
OBJECT IDENTIFIER    

spareDevNumber 1.3.6.1.4.1.3582.4.1.4.3.5.1
The present number of rows in the sparepool table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

spareTable 1.3.6.1.4.1.3582.4.1.4.3.5.2
A List of sparepool Entries containing Information/Properties about the spare drive
Status: optional Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SpareEntry

spareEntry 1.3.6.1.4.1.3582.4.1.4.3.5.2.1
An Entry in the sparepool Table.
Status: optional Access: not-accessible
OBJECT-TYPE    
  SpareEntry  

spareID 1.3.6.1.4.1.3582.4.1.4.3.5.2.1.1
The unique Device ID
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

deviceIdentification 1.3.6.1.4.1.3582.4.1.4.3.5.2.1.2
The unique Device ID
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

spareType 1.3.6.1.4.1.3582.4.1.4.3.5.2.1.3
Spare type. isDedicated(0/1)isRevertible(0/1)isEnclAffinity(0/1). 1 implies particular feature is enable and 0 represent feature is disable.
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

arrayCount 1.3.6.1.4.1.3582.4.1.4.3.5.2.1.4
The number of arrays to which the Physical Drive can be dedicated
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

arrayIDs 1.3.6.1.4.1.3582.4.1.4.3.5.2.1.5
Comma separated array ids. e.g. 2,4,5 etc
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

adapterID-ST 1.3.6.1.4.1.3582.4.1.4.3.5.2.1.6
Adapter ID.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

enclosureInfo 1.3.6.1.4.1.3582.4.1.5
OBJECT IDENTIFIER    

enclosureNumber 1.3.6.1.4.1.3582.4.1.5.1
The present number of rows in the enclosure table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

enclosureTable 1.3.6.1.4.1.3582.4.1.5.2
A List of Enclosure Entries containing Information/Properties about the enclosures in the system.
Status: optional Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EnclosureEntry

enclosureEntry 1.3.6.1.4.1.3582.4.1.5.2.1
An Entry in the enclosure table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  EnclosureEntry  

enclosureID 1.3.6.1.4.1.3582.4.1.5.2.1.1
EnclosureID for this enclosure.(Unique)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

deviceId 1.3.6.1.4.1.3582.4.1.5.2.1.2
Enclosure device Id.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

enclosureIndex 1.3.6.1.4.1.3582.4.1.5.2.1.3
Firmware internal enclosure index
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

slotCount 1.3.6.1.4.1.3582.4.1.5.2.1.4
Number of slots
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

psCount 1.3.6.1.4.1.3582.4.1.5.2.1.5
Number of power supplies
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

fanCount 1.3.6.1.4.1.3582.4.1.5.2.1.6
Number of fans
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

tempSensorCount 1.3.6.1.4.1.3582.4.1.5.2.1.7
Number of temperature sensors
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

alarmCount 1.3.6.1.4.1.3582.4.1.5.2.1.8
Number of alarms
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

simCount 1.3.6.1.4.1.3582.4.1.5.2.1.9
Number of SIM modules
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

isFault 1.3.6.1.4.1.3582.4.1.5.2.1.10
Enclosure has entered a FAULT state or not. Values: false(0),true(1)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

pdCount 1.3.6.1.4.1.3582.4.1.5.2.1.11
Number of physical drives present
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

pdIds 1.3.6.1.4.1.3582.4.1.5.2.1.12
Physical drive deviceIds space separated.
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

adapterID-ET 1.3.6.1.4.1.3582.4.1.5.2.1.13
Adapter ID.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

pdCountSpinup60 1.3.6.1.4.1.3582.4.1.5.2.1.14
Number of drives that can spun up in 60 sec.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

enclosureType 1.3.6.1.4.1.3582.4.1.5.2.1.15
Information about type of enclosure : 0= UNKNOWN ,1= SAFTE ,2=SES ,3= SGPIO.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

enclFirmwareVersion 1.3.6.1.4.1.3582.4.1.5.2.1.16
Information about enclosure FW Version
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

enclSerialNumber 1.3.6.1.4.1.3582.4.1.5.2.1.17
Enclosure Serial Number
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

vendorID 1.3.6.1.4.1.3582.4.1.5.2.1.18
Enclosure Vendor ID
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

productID 1.3.6.1.4.1.3582.4.1.5.2.1.19
Enclosure Product ID
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

eSMSerialNumber 1.3.6.1.4.1.3582.4.1.5.2.1.20
IBM Enclosure ESM Serial Number
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

eSMFRU 1.3.6.1.4.1.3582.4.1.5.2.1.21
Information about IBM Enclosure ESM FRU
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

enclosureZoningMode 1.3.6.1.4.1.3582.4.1.5.2.1.22
Enclosure IBM Zoning Mode
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

eSMFRUPartInfo 1.3.6.1.4.1.3582.4.1.5.2.1.23
Information about IBM Enclosure ESM FRU Part
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

enclosureFanTable 1.3.6.1.4.1.3582.4.1.5.3
A List of fan Entries containing Information/Properties about the enclosureFan.
Status: optional Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EnclosureFanEntry

enclosureFanEntry 1.3.6.1.4.1.3582.4.1.5.3.1
An Entry in the enclosureFan table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  EnclosureFanEntry  

fanID 1.3.6.1.4.1.3582.4.1.5.3.1.1
ID for this EnclosureFan.(Unique)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

enclosureId 1.3.6.1.4.1.3582.4.1.5.3.1.2
Enclosure ID where the fan is attached
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

fanStatus 1.3.6.1.4.1.3582.4.1.5.3.1.3
status of the fan
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER status-invalid(1), status-ok(2), status-critical(3), status-nonCritical(4), status-unrecoverable(5), status-not-installed(6), status-unknown(7), status-not-available(8)  

enclosureSlotTable 1.3.6.1.4.1.3582.4.1.5.4
A List of slot Entries containing Information/Properties about the enclosure slots.
Status: optional Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EnclosureSlotEntry

enclosureSlotEntry 1.3.6.1.4.1.3582.4.1.5.4.1
An Entry in the enclosureSlot table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  EnclosureSlotEntry  

slotID 1.3.6.1.4.1.3582.4.1.5.4.1.1
ID for this slot.(Unique)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

enclosureId-EST 1.3.6.1.4.1.3582.4.1.5.4.1.2
enclosure ID
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

slotStatus 1.3.6.1.4.1.3582.4.1.5.4.1.3
status of the device
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER status-invalid(1), status-ok(2), status-critical(3), status-nonCritical(4), status-unrecoverable(5), status-not-installed(6), status-unknown(7), status-not-available(8)  

enclosurePowerSupplyTable 1.3.6.1.4.1.3582.4.1.5.5
A List of powerSupply Entries containing Information/Properties about the enclosure powerSupply
Status: optional Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EnclosurePowerSupplyEntry

enclosurePowerSupplyEntry 1.3.6.1.4.1.3582.4.1.5.5.1
An Entry in the powerSupply table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  EnclosurePowerSupplyEntry  

powerSupplyID 1.3.6.1.4.1.3582.4.1.5.5.1.1
ID for this powerSupply.(Unique)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

enclosureId-EPST 1.3.6.1.4.1.3582.4.1.5.5.1.2
Enclosure id for the powerSupply
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

powerSupplyStatus 1.3.6.1.4.1.3582.4.1.5.5.1.3
Status of the power Supply
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER status-invalid(1), status-ok(2), status-critical(3), status-nonCritical(4), status-unrecoverable(5), status-not-installed(6), status-unknown(7), status-not-available(8)  

enclosureTempSensorTable 1.3.6.1.4.1.3582.4.1.5.6
A List of TempSensor Entries containing Information/Properties about the enclosure TempSensor
Status: optional Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EnclosureTempSensorEntry

enclosureTempSensorEntry 1.3.6.1.4.1.3582.4.1.5.6.1
An Entry in the adapter table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  EnclosureTempSensorEntry  

tempSensorID 1.3.6.1.4.1.3582.4.1.5.6.1.1
ID for this TempSensor.(Unique)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

enclosureId-ETST 1.3.6.1.4.1.3582.4.1.5.6.1.2
Enclosure id for this TempSensor
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

tempSensorStatus 1.3.6.1.4.1.3582.4.1.5.6.1.3
Status of the Temparature Sensor
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER status-invalid(1), status-ok(2), status-critical(3), status-nonCritical(4), status-unrecoverable(5), status-not-installed(6), status-unknown(7), status-not-available(8)  

enclosureTemperature 1.3.6.1.4.1.3582.4.1.5.6.1.4
Current temperature in degree Centigrade
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

enclosureAlarmTable 1.3.6.1.4.1.3582.4.1.5.7
A List of Alarm Entries containing Information/Properties about enclosure Alarms
Status: optional Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EnclosureAlarmEntry

enclosureAlarmEntry 1.3.6.1.4.1.3582.4.1.5.7.1
An Entry in the enclosureAlarm table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  EnclosureAlarmEntry  

alarmID 1.3.6.1.4.1.3582.4.1.5.7.1.1
ID for this Alarm.(Unique)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

enclosureId-EAT 1.3.6.1.4.1.3582.4.1.5.7.1.2
Enclosure id where the Alarm is attached
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

alarmStatus 1.3.6.1.4.1.3582.4.1.5.7.1.3
Status of the alarm
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER status-invalid(1), status-ok(2), status-critical(3), status-nonCritical(4), status-unrecoverable(5), status-not-installed(6), status-unknown(7), status-not-available(8)  

enclosureSIMTable 1.3.6.1.4.1.3582.4.1.5.8
A List of SIM Entries containing Information/Properties about enclosure SIMs
Status: optional Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EnclosureSIMEntry

enclosureSIMEntry 1.3.6.1.4.1.3582.4.1.5.8.1
An Entry in the enclosureSIM table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  EnclosureSIMEntry  

simID 1.3.6.1.4.1.3582.4.1.5.8.1.1
ID for this SIM.(Unique)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

enclosureId-ESIT 1.3.6.1.4.1.3582.4.1.5.8.1.2
Inclosure ID where the SIM is attached
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

simStatus 1.3.6.1.4.1.3582.4.1.5.8.1.3
Status of the SIM
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER status-invalid(1), status-ok(2), status-critical(3), status-nonCritical(4), status-unrecoverable(5), status-not-installed(6), status-unknown(7), status-not-available(8)  

adapterTraps 1.3.6.1.4.1.3582.4.1.6
OBJECT IDENTIFIER    

atAdpNumber 1.3.6.1.4.1.3582.4.1.6.1001
Adapter ID for which Trap is generated.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

atAlarmState 1.3.6.1.4.1.3582.4.1.6.1002
Alarm disabled/enabled. Values: disabled(0),enabled(1)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

atRate 1.3.6.1.4.1.3582.4.1.6.1003
BGI/Check Consistency/Rebuild/Patrol Read/Reconstruction Rate
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

atFlashImageName 1.3.6.1.4.1.3582.4.1.6.1004
Flash Image Name
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

atID 1.3.6.1.4.1.3582.4.1.6.1005
ID
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

clustCtrlpropReset 1.3.6.1.4.1.3582.4.1.6.1006
Resetting controller property
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

adpAlarmStateEnabled 8001
Alarm has been enabled by user for Adapter $1
TRAP-TYPE    

adpBGIRateChanged 8002
Background initialization rate changed to $1 for Adapter $2
TRAP-TYPE    

adpCacheDiscarded 8003
Controller $1 cache discarded due to memory/battery problems
TRAP-TYPE    

adpCacheRebootCantRecover 8004
Unable to recover cache data due to configuration mismatch for Adapter $1
TRAP-TYPE    

adpCacheRebootRecover 8005
Cache data recovered successfully for Adapter $1
TRAP-TYPE    

adpCacheVersionMismatch 8006
Controller cache discarded due to firmware version incompatibility for Adapter $1
TRAP-TYPE    

adpCCRateChanged 8007
Consistency Check rate changed to $1 for Adapter $2
TRAP-TYPE    

adpFlashBadImage 8008
Flash downloaded image corrupted for Adapter $1
TRAP-TYPE    

adpFlashEraseError 8009
Flash erase error for Adapter $1
TRAP-TYPE    

adpFlashEraseTimeout 8010
Flash timeout during erase for Adapter $1
TRAP-TYPE    

adpFlashGeneralError 8011
Flash error for Adapter $1
TRAP-TYPE    

adpFlashImage 8012
Flashing image: $1 for Adapter $2
TRAP-TYPE    

adpFlashOK 8013
Flash of new firmware image(s)complete for Adapter $1
TRAP-TYPE    

adpFlashProgramError 8014
Flash programming error for Adapter $1
TRAP-TYPE    

adpFlashProgramTimeout 8015
Flash timeout during programming for Adapter $1
TRAP-TYPE    

adpLogCleared 8016
Event log cleared for Adapter $1
TRAP-TYPE    

adpLogWrapped 8017
Event log wrapped for Adapter $1
TRAP-TYPE    

adpPatrolReadComplete 8018
Patrol Read complete for Adapter $1
TRAP-TYPE    

adpPatrolReadPaused 8019
Patrol Read paused for Adapter $1
TRAP-TYPE    

adpPatrolReadResumed 8020
Patrol Read resumed for Adapter $1
TRAP-TYPE    

adpPatrolReadStarted 8021
Patrol Read started for Adapter $1
TRAP-TYPE    

adpShutdown 8022
Shutdown command received for Adapter $1
TRAP-TYPE    

adpHibernate 8023
Hibernate command received for Adapter $1
TRAP-TYPE    

adpCrash 8024
Fatal error received for Adapter $1
TRAP-TYPE    

adpRRChanged 8025
Rebuild rate changed to $1 for Adapter $2
TRAP-TYPE    

adpPRRateChanged 8026
Patrol Read rate changed to $1 for Adapter $2
TRAP-TYPE    

adpAlarmStateDisabled 8027
Alarm has been disabled by user for Adapter $1
TRAP-TYPE    

adpConfigCleared 8028
Configuration cleared for Adapter $1
TRAP-TYPE    

adpReconRateChanged 8029
Reconstruction rate changed to $1 for Adapter $2
TRAP-TYPE    

adpDefault 8030
Factory defaults restored for Adapter $1
TRAP-TYPE    

bbuPresent 8031
Battery Present for Adapter $1
TRAP-TYPE    

bbuNotPresent 8032
Battery Not Present for Adapter $1
TRAP-TYPE    

bbuNewBattery 8033
New Battery Detected for Adapter $1
TRAP-TYPE    

bbuReplaced 8034
Battery has been replaced for Adapter $1
TRAP-TYPE    

bbuTempHigh 8035
Battery temperature is high for Adapter $1
TRAP-TYPE    

bbuVoltageLow 8036
Battery voltage low for Adapter $1
TRAP-TYPE    

bbuCharging 8037
Battery started charging for Adapter $1
TRAP-TYPE    

bbuDisCharging 8038
Battery is discharging for Adapter $1
TRAP-TYPE    

bbuTempNormal 8039
Battery temperature is normal for Adapter $1
TRAP-TYPE    

bbuReplace 8040
Battery needs replacement, SOH Bad for Adapter $1
TRAP-TYPE    

bbuRelearnStarted 8041
Battery relearn started for Adapter $1
TRAP-TYPE    

bbuRelearnProgress 8042
Battery relearn in progress for Adapter $1
TRAP-TYPE    

bbuRelearnComplete 8043
Battery relearn completed for Adapter $1
TRAP-TYPE    

bbuRelearnTimeout 8044
Battery relearn timed out for Adapter $1
TRAP-TYPE    

bbuRelearnPending 8045
Battery relearn pending: Battery is under charge for Adapter $1
TRAP-TYPE    

bbuRelearnPostponed 8046
Battery relearn postponed for Adapter $1
TRAP-TYPE    

bbuRemoved 8047
Battery removed for Adapter $1
TRAP-TYPE    

bbuCapacityLow 8048
Current capacity of the battery is below threshold for Adapter $1
TRAP-TYPE    

bbuCapacityAbove 8049
Current capacity of the battery is above threshold for Adapter $1
TRAP-TYPE    

bbuFRU 8050
Bbu FRU for Adapter $1 changed
TRAP-TYPE    

revisionIdentifier 8051
Revision Identifier for Adapter $1 changed
TRAP-TYPE    

adpLockKeyCreated 8052
Drive security key created for Adapter $1
TRAP-TYPE    

adpLockKeyBackedup 8053
Drive security key backed up for Adapter $1
TRAP-TYPE    

adpLockKeyVerifiedEscrow 8054
Drive security key from escrow, verified for Adapter $1
TRAP-TYPE    

adpLockKeyRekeyed 8055
Drive security key changed for Adapter $1
TRAP-TYPE    

adpLockKeyRekeyFailed 8056
Drive security key, re-key operation failed for Adapter $1
TRAP-TYPE    

adpLockKeyInvalid 8057
Drive security key is invalid for Adapter $1
TRAP-TYPE    

adpLockKeyDestroyed 8058
Drive security key destroyed for Adapter $1
TRAP-TYPE    

adpEscrowKeyInvalid 8059
Drive security key from escrow is invalid for Adapter $1
TRAP-TYPE    

adpLockKeyFailed 8060
Drive security key failure, cannot access secured configuration for Adapter $1
TRAP-TYPE    

bbuChargeDisabled 8061
Battery charging was suspended due to high battery temperature on Adapter $1
TRAP-TYPE    

bbuMicrocodeUpdated 8062
Battery NVCache firmware update was successful on Adapter $1
TRAP-TYPE    

bbuMicrocodeUpdateFailed 8063
Battery NVCache firmware update failed on Adapter $1
TRAP-TYPE    

haNodeJoin 8064
Peer controller entered HA Domain at Adapter -$1
TRAP-TYPE    

haNodeBreak 8065
Peer controller exited HA Domain at Adapter -$1
TRAP-TYPE    

haPeerIncompatible 8066
Peer controller settings are incompatible
TRAP-TYPE    

haCtrlpropIncompatible 8067
Controller property mismatch detected with Peer controller
TRAP-TYPE    

haFWVersionMismatch 8068
FW version does not match Peer controller
TRAP-TYPE    

haCacheMirrorOnline 8069
Cache mirroring is online
TRAP-TYPE    

haCacheMirrorOffline 8070
Cache mirroring is offline
TRAP-TYPE    

adpPropChanged 8071
Controller properties changed for Adapter $1
TRAP-TYPE    

adpResetNowStart 8072
Controller reset requested by host for Adapter $1
TRAP-TYPE    

adpResetNowDone 8073
Controller reset requested by host, completed for Adapter $1
TRAP-TYPE    

vdTraps 1.3.6.1.4.1.3582.4.1.7
OBJECT IDENTIFIER    

vdNumber 1.3.6.1.4.1.3582.4.1.7.1101
vd Target ID for which Trap is generated.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

vdSeq 1.3.6.1.4.1.3582.4.1.7.1102
vd Sequence no for which Trap is generated.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

vdProg 1.3.6.1.4.1.3582.4.1.7.1103
progress %
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

vdCachePolicyChangeReason 1.3.6.1.4.1.3582.4.1.7.1104
VD cache policy.
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

vdNewState 1.3.6.1.4.1.3582.4.1.7.1105
Virtual Drive state. Values are: offline(0),partially-degraded(1),degraded(2),optimal(3)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

vdOldState 1.3.6.1.4.1.3582.4.1.7.1106
Virtual Drive state. Values are: offline(0),partially-degraded(1),degraded(2),optimal(3)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

isRemote 1.3.6.1.4.1.3582.4.1.7.1107
HA cluster locale: 0=local, 1=remote (at peer)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

vdtBGIAborted 8101
BGI aborted on Adapter -$1 VD Target -$2 Remote VD -$3
TRAP-TYPE    

vdtBGICompleted 8102
BGI completed on Adapter -$1 VD Target -$2 Remote VD -$3
TRAP-TYPE    

vdtBGIDoneWR 8103
BGI completed with uncorrectable errors on Adapter -$1 VD Target -$2 Remote VD -$3
TRAP-TYPE    

vdtBGIFailed 8104
BGI failed on Adapter -$1 VD Target -$2 Remote VD -$3
TRAP-TYPE    

vdtBGIStarted 8105
BGI started on Adapter -$1 VD Target -$2 Remote VD -$3
TRAP-TYPE    

vdtCCStarted 8107
CC started on Adapter -$1 VD Target -$2 Remote VD -$3
TRAP-TYPE    

vdtCCCompleted 8108
CC completed on Adapter -$1 VD Target -$2 Remote VD -$3
TRAP-TYPE    

vdtCCFailed 8109
CC failed on Adapter -$1 VD Target -$2 Remote VD -$3
TRAP-TYPE    

vdtCCAborted 8110
CC aborted on Adapter -$1 VD Target -$2 Remote VD -$3
TRAP-TYPE    

vdtCCCompCor 8111
CC completed with correction on Adapter -$1 VD Target -$2 Remote VD -$3
TRAP-TYPE    

vdtInitAborted 8112
Initialization aborted on Adapter -$1 VD Target -$2 Remote VD -$3
TRAP-TYPE    

vdtInitFailed 8113
Initialization failed on Adapter -$1 VD Target -$2 Remote VD -$3
TRAP-TYPE    

vdtInitCompleted 8114
Initialization completed on Adapter -$1 VD Target -$2 Remote VD -$3
TRAP-TYPE    

vdtInitFastStarted 8115
Fast Initialization started on Adapter -$1 VD Target -$2 Remote VD -$3
TRAP-TYPE    

vdtInitFullStarted 8116
Full Initialization started on Adapter-$1 VD Target-$2 Remote VD -$3
TRAP-TYPE    

vdtReconStarted 8117
Reconstruction started on Adapter-$1 VD Target-$2 Remote VD -$3
TRAP-TYPE    

vdtReconCompleted 8118
Reconstruction completed on Adapter -$1 VD Target -$2 Remote VD -$3
TRAP-TYPE    

vdtReconResumed 8119
Reconstruction resumed on Adapter -$1 VD Target -$2 Remote VD -$3
TRAP-TYPE    

vdtReconStopped 8120
Reconstruction stopped on Adapter-$1 VD Target-$2 Remote VD -$3
TRAP-TYPE    

vdtStateChange 8121
VD state changed on Adapter -$1 VD Target -$2 from $3 to $4
TRAP-TYPE    

vdtCreated 8122
A new VD created on Adapter -$1 VD Target -$2 Remote VD -$3
TRAP-TYPE    

vdtDeleted 8123
A VD deleted on Adapter -$1 VD Target -$2 Remote VD -$3
TRAP-TYPE    

vdtSecured 8124
VD is now secured. Adapter -$1 VD Targt -$2 Remote VD -$3
TRAP-TYPE    

vdtPartiallySecured 8125
VD is partially secured. Adapter -$1 VD Targt -$2 Remote VD -$3
TRAP-TYPE    

vdtBbmLogCleared 8126
VD bad block table cleared on Adapter -$1 VD Targt -$2 Remote VD -$3
TRAP-TYPE    

vdtERASEAborted 8127
LD Erase aborted on aborted on Adapter -$1 VD Target -$2 Remote VD -$3
TRAP-TYPE    

vdtERASECompleted 8128
LD Erase completed on Adapter -$1 VD Target -$2 Remote VD -$3
TRAP-TYPE    

vdtERASEFailed 8129
LD Erase failed on Adapter -$1 VD Target -$2 Remote VD -$3
TRAP-TYPE    

vdtERASEStarted 8130
LD Erase started on Adapter -$1 VD Target -$2 Remote VD -$3
TRAP-TYPE    

vdtSSCDISASSOCIATEStarted 8131
CacheCade(TM) disassociate started on Adapter -$1 VD Target -$2 Remote VD -$3
TRAP-TYPE    

vdtSSCDISASSOCIATECompleted 8132
CacheCade(TM) disassociate completed on Adapter -$1 VD Target -$2 Remote VD -$3
TRAP-TYPE    

vdtSSCDISASSOCIATEFailed 8133
CacheCade(TM) disassociate failed on Adapter -$1 VD Target -$2 Remote VD -$3
TRAP-TYPE    

vdtSSCDISASSOCIATEAborted 8134
CacheCade(TM) disassociate aborted by user on Adapter -$1 VD Target -$2 Remote VD -$3
TRAP-TYPE    

vdtACCESSBLOCKEDSSCOFFLINE 8135
Access blocked as cached data in CacheCade(TM) is unavailable on Adapter -$1 VD Target -$2 Remote VD -$3
TRAP-TYPE    

haLDIsRemote 8136
Peer controller now manages LD on Adapter -$1 VD Target -$2 Remote VD -$3
TRAP-TYPE    

haLDIsLocal 8137
Local controller now manages VD on Adapter -$1 VD Target -$2 Remote VD -$3
TRAP-TYPE    

haLDTargetIDConflict 8138
Target ID conflict detected. VD on Adapter -$1 VD Target -$2 Remote VD -$3 access is restricted from Peer controller
TRAP-TYPE    

haLDAccessShared 8139
Shared access set for VD on Adapter -$1 VD Target -$2 Remote VD -$3
TRAP-TYPE    

haLDAccessExclusive 8140
Exclusive access set for VD on Adapter -$1 VD Target -$2 Remote VD -$3
TRAP-TYPE    

haLDIncompatible 8141
Adapter -$1 VD Target -$2 Remote VD -$3 is incompatible in the HA domain
TRAP-TYPE    

vdAccessBlockedPeerUnavailable 8142
Cached data from peer controller is unavailable. LD on Adapter -$1 VD Target -$2 Remote VD -$3 access policy is set to Blocked
TRAP-TYPE    

pdTraps 1.3.6.1.4.1.3582.4.1.8
OBJECT IDENTIFIER    

pdID 1.3.6.1.4.1.3582.4.1.8.1201
Device ID for which Trap is generated.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

pdEncIndex 1.3.6.1.4.1.3582.4.1.8.1202
Enclosure index(0 means not within an enclosure) for which Trap is generated.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

pdSlotNo 1.3.6.1.4.1.3582.4.1.8.1203
Slot no for the enclosure
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

pdNewState 1.3.6.1.4.1.3582.4.1.8.1204
Physical Drive state. Values are: unconfigured-good(0),unconfigured-bad(1),hot-spare(2),offline(16),failed(17),rebuild(20),online(24),copyback(32),system(64)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

pdOldState 1.3.6.1.4.1.3582.4.1.8.1205
Physical Drive state. Values are: unconfigured-good(0),unconfigured-bad(1),hot-spare(2),offline(16),failed(17),rebuild(20),online(24),copyback(32),system(64)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

pdEnclDeviceId 1.3.6.1.4.1.3582.4.1.8.1206
Enclosure Device ID for which Trap is generated.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

pdSASAdd 1.3.6.1.4.1.3582.4.1.8.1207
Device SAS addresses. Comma separeted for multiple address.
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

pdPath 1.3.6.1.4.1.3582.4.1.8.1208
PD path.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

pdFRU 1.3.6.1.4.1.3582.4.1.8.1209
PD FRU for which trap is generated.
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

pdNewPowerState 1.3.6.1.4.1.3582.4.1.8.1210
New Power Status Of the Device.Values are device is active(0),device is stopped(1),device is transitioning between power states(255)
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

pdtClearAborted 8201
Physical Drive Clear aborted on Adapter -$1 Dev -$2 Enc -$3 Slot -$4
TRAP-TYPE    

pdtClearFailed 8202
Physical Drive Clear failed on Adapter -$1 Dev -$2 Enc -$3 Slot -$4
TRAP-TYPE    

pdtClearStarted 8203
Physical Drive Clear started on Adapter -$1 Dev -$2 Enc -$3 Slot -$4
TRAP-TYPE    

pdtClearCompleted 8204
Physical Drive Clear completed on Adapter -$1 Dev -$2 Enc -$3 Slot -$4
TRAP-TYPE    

pdtError 8205
Error occurred on Adapter -$1 Dev -$2 Enc -$3 Slot -$4
TRAP-TYPE    

pdtFormatStart 8206
Physical Drive format started on Adapter -$1 Dev -$2 Enc -$3 Slot -$4
TRAP-TYPE    

pdtFormatCompleted 8207
Physical Drive format completed on Adapter -$1 Dev -$2 Enc -$3 Slot -$4
TRAP-TYPE    

pdtInserted 8208
PD inserted on Adapter -$1 Dev -$2 Enc -$3 Slot -$4
TRAP-TYPE    

pdtRblAborted 8209
Rebuild aborted on Adapter -$1 Dev -$2 Enc -$3 Slot -$4
TRAP-TYPE    

pdtRblCompleted 8210
Rebuild completed on Adapter -$1 Dev -$2 Enc -$3 Slot -$4
TRAP-TYPE    

pdtRblFailedBS 8211
Rebuild failed(bad source) on Adapter -$1 Dev -$2 Enc -$3 Slot -$4
TRAP-TYPE    

pdtRblFailedBT 8212
Rebuild failed(bad target) on Adapter -$1 Dev -$2 Enc -$3 Slot -$4
TRAP-TYPE    

pdtRblStart 8213
Rebuild started on Adapter -$1 Dev -$2 Enc -$3 Slot -$4
TRAP-TYPE    

pdtRblResumed 8214
Rebuild resumed on Adapter -$1 Dev -$2 Enc -$3 Slot -$4
TRAP-TYPE    

pdtRblStartA 8215
Rebuild started(auto) on Adapter -$1 Dev -$2 Enc -$3 Slot -$4
TRAP-TYPE    

pdtRemoved 8216
Physical Drive removed on Adapter -$1 Dev -$2 Enc -$3 Slot -$4
TRAP-TYPE    

pdtStateChange 8217
PD state changed on Adapter -$1 Dev -$2 Enc -$3 Slot -$4 from $5 to $6
TRAP-TYPE    

pdtRedundantPathBroken 8218
Redundant Path Broken For Physical Drive on Adapter -$1 Dev -$2 Enc -$3 Slot -$4 EncDevId -$5 pdSAS -$6
TRAP-TYPE    

pdtRedundantPathRestored 8219
Redundant Path Restored For Physical Drive on Adapter -$1 Dev -$2 Enc -$3 Slot -$4 EncDevId -$5 pdSAS -$6
TRAP-TYPE    

pdtRedundantEnclModuleInserted 8220
Redundant Encl Modul Inserted on Adapter -$1 Dev -$2 Enc -$3 Slot -$4 EncDevId -$5 pdSAS -$6 pdpath -$7
TRAP-TYPE    

pdtRedundantEnclModuleRemoved 8221
Redundant Encl Modul Removed on Adapter -$1 Dev -$2 Enc -$3 Slot -$4 EncDevId -$5 pdSAS -$6 pdpath -$7
TRAP-TYPE    

pdtFRU 8222
FRU changed on Adapter -$1 Dev -$2 Enc -$3 Slot -$4 EncDevId -$5 -FRU $6
TRAP-TYPE    

pdtSecured 8223
PD security activated on Adapter -$1 Dev -$2 Enc -$3 Slot -$4
TRAP-TYPE    

pdtUnsecured 8224
PD security disabled on Adapter -$1 Dev -$2 Enc -$3 Slot -$4
TRAP-TYPE    

pdtReprovisioned 8225
PD is reprovisioned on Adapter -$1 Dev -$2 Enc -$3 Slot -$4
TRAP-TYPE    

pdtLockKeyRekeyed 8226
PD security key changed on Adapter -$1 Dev -$2 Enc -$3 Slot -$4
TRAP-TYPE    

pdtSecurityFailure 8227
Security subsystem problems detected on Adapter -$1 Dev -$2 Enc -$3 Slot -$4
TRAP-TYPE    

pdtPowerStateChange 8228
Power State Change on Adapter -$1 Dev -$2 Enc -$3 Slot -$4 NewPowerState -$5
TRAP-TYPE    

pdtNotSupported 8229
PD Not Supported on Adapter -$1 Dev -$2 Enc -$3 Slot -$4
TRAP-TYPE    

pdtNotCertified 8230
PD Not Certified on Adapter -$1 Dev -$2 Enc -$3 Slot -$4
TRAP-TYPE    

pdtERASEAborted 8231
PD Erase aborted on Adapter -$1 Dev -$2 Enc -$3 Slot -$4
TRAP-TYPE    

pdtERASECompleted 8232
PD Erase completed on Adapter -$1 Dev -$2 Enc -$3 Slot -$4
TRAP-TYPE    

pdtERASEStarted 8233
PD Erase started on Adapter -$1 Dev -$2 Enc -$3 Slot -$4
TRAP-TYPE    

pdtERASEFailed 8234
PD Erase Failed on Adapter -$1 Dev -$2 Enc -$3 Slot -$4
TRAP-TYPE    

haPDIsRemote 8235
Peer controller now manages PD on Adapter -$1 Dev -$2 Enc -$3 Slot -$4
TRAP-TYPE    

haPDIsLocal 8236
Local controller now manages PD on Adapter -$1 Dev -$2 Enc -$3 Slot -$4
TRAP-TYPE    

enclTraps 1.3.6.1.4.1.3582.4.1.9
OBJECT IDENTIFIER    

atPort 1.3.6.1.4.1.3582.4.1.9.1301
Prot no.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

onPHY 1.3.6.1.4.1.3582.4.1.9.1302
PHY no
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

widePortLinkLost 8330
Link lost on SAS wide port on Adapter -$1 port -$2 PHY -$3
TRAP-TYPE    

widePortLinkRestored 8331
Link Restored on SAS wide port on Adapter -$1 port -$2 PHY -$3
TRAP-TYPE    

pciTraps 1.3.6.1.4.1.3582.4.1.10
OBJECT IDENTIFIER    

pciVendorId 1.3.6.1.4.1.3582.4.1.10.1501
PCI VendorID
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

pciDeviceId 1.3.6.1.4.1.3582.4.1.10.1502
PCI Device ID
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

pciSubVendorId 1.3.6.1.4.1.3582.4.1.10.1503
PCI SubVendorID
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

pciSubDeviceId 1.3.6.1.4.1.3582.4.1.10.1504
PCI SubDeviceID
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

haHwIncompatible 8501
Peer Controller hardware is incompatible
TRAP-TYPE    

copyrightInfo 1.3.6.1.4.1.3582.4.1.11
OBJECT IDENTIFIER