Juniper-IP-POLICY-MIB

File: Juniper-IP-POLICY-MIB.mib (79453 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
Juniper-MIBs

Imported symbols

MODULE-IDENTITY OBJECT-TYPE IpAddress
Counter32 Integer32 TEXTUAL-CONVENTION
RowStatus DisplayString TruthValue
MODULE-COMPLIANCE OBJECT-GROUP juniMibs

Defined Types

JuniIpPolicyName  
IP access list name. Represents textual information taken from the NVT ASCII character set.
TEXTUAL-CONVENTION    
  OCTET STRING Size(0..32)  

JuniIpPolicyPolicy  
The set of IP policy actions.
TEXTUAL-CONVENTION    
  INTEGER permit(0), deny(1)  

JuniIpDynRedistributeProtocol  
The set of protocols choices used to configure to/from settings in an IP Dynamic Route Redistribution element.
TEXTUAL-CONVENTION    
  INTEGER ipRedistrProtocolIsis(1), ipRedistrProtocolRip(2), ipRedistrProtocolOspf(3), ipRedistrProtocolStatic(4), ipRedistrProtocolConnected(5), ipRedistrProtocolBgp(6), ipRedistrProtocolMBgp(7), ipRedistrProtocolStaticLow(8), ipRedistrProtocolOspfIntern(9), ipRedistrProtocolOspfExtern(10), ipRedistrProtocolDvmrp(11), ipRedistrProtocolDvmrpAggregate(12), ipRedistrProtocolHidden(13), ipRedistrProtocolOwnerAccess(14), ipRedistrProtocolOwnerAccessInternal(15), ipRedistrProtocolOwnerDialout(16), ipRedistrProtocolDefaultRoute(17)  

JuniIpRedistributeProtocol  
The set of protocols choices used to configure to/from settings in an IP Redistribution element.
TEXTUAL-CONVENTION    
  INTEGER ipRedistrProtocolStatic(1), ipRedistrProtocolBgp(2), ipRedistrProtocolMBgp(3), ipRedistrProtocolOspf(4), ipRedistrProtocolIsis(5), ipRedistrProtocolRip(6), ipRedistrProtocolConnected(7), ipRedistrProtocolDefaultRoute(8), ipRedistrProtocolAccess(9), ipRedistrProtocolAccessInternal(10), ipRedistrProtocolDvmrp(11), ipRedistrProtocolDialout(12), ipRedistrProtocolOspfM(13), ipRedistrProtocolStaticMcast(14), ipRedistrProtocolLdpUcast(15)  

JuniIpPolicyAdminStatus  
The administratively assigned management state for an IP route policy.
TEXTUAL-CONVENTION    
  INTEGER ipPolicyAdminStateDisable(0), ipPolicyAdminStateEnable(1)  

JuniIpPolicyExtendedCommunity  
The extended community specification. Represents textual information taken from the NVT ASCII character set. The format of the text string is defined by either one of these choices: In: ASN::nn where ASN is a 16 bit decimal number and nn is a 32 bit decimal number Or: IP-address::nn where IP-address is in dotted decimal format and nn is a 16 bit decimal number
TEXTUAL-CONVENTION    
  OCTET STRING Size(0..22)  

JuniIpAccessListEntry  
SEQUENCE    
  juniIpAccessListId Integer32
  juniIpAccessListElemId Integer32
  juniIpAccessListRowStatus RowStatus
  juniIpAccessListAction JuniIpPolicyPolicy
  juniIpAccessListSrc IpAddress
  juniIpAccessListSrcMask IpAddress
  juniIpAccessListDst IpAddress
  juniIpAccessListDstMask IpAddress
  juniIpAccessListProtocol Integer32

JuniIpNamedAccessListEntry  
SEQUENCE    
  juniIpNamedAccessListName JuniIpPolicyName
  juniIpNamedAccessListElemId Integer32
  juniIpNamedAccessListRowStatus RowStatus
  juniIpNamedAccessListAction JuniIpPolicyPolicy
  juniIpNamedAccessListSrc IpAddress
  juniIpNamedAccessListSrcMask IpAddress
  juniIpNamedAccessListDst IpAddress
  juniIpNamedAccessListDstMask IpAddress
  juniIpNamedAccessListProtocol Integer32

JuniIpAspAccessEntry  
SEQUENCE    
  juniIpAspAccessName JuniIpPolicyName
  juniIpAspAccessElemId Integer32
  juniIpAspAccessCreatedInternally TruthValue
  juniIpAspAccessPolicy JuniIpPolicyPolicy
  juniIpAspAccessExpression OCTET STRING
  juniIpAspAccessRowStatus RowStatus

JuniIpPrefixListEntry  
SEQUENCE    
  juniIpPrefixListName JuniIpPolicyName
  juniIpPrefixListElemId Integer32
  juniIpPrefixListIpAddress IpAddress
  juniIpPrefixListLength Integer32
  juniIpPrefixListPolicy JuniIpPolicyPolicy
  juniIpPrefixListGeValue Integer32
  juniIpPrefixListLeValue Integer32
  juniIpPrefixListDescription DisplayString
  juniIpPrefixListHitCount Counter32
  juniIpPrefixListRowStatus RowStatus

JuniIpPrefixTreeEntry  
SEQUENCE    
  juniIpPrefixTreeName JuniIpPolicyName
  juniIpPrefixTreeIpAddress IpAddress
  juniIpPrefixTreeLength Integer32
  juniIpPrefixTreePolicy JuniIpPolicyPolicy
  juniIpPrefixTreeDescription DisplayString
  juniIpPrefixTreeHitCount Counter32
  juniIpPrefixTreeRowStatus RowStatus

JuniIpCommunityListEntry  
SEQUENCE    
  juniIpCommunityListName JuniIpPolicyName
  juniIpCommunityListElemId Integer32
  juniIpCommunityListCreatedInternally TruthValue
  juniIpCommunityListExtended TruthValue
  juniIpCommunityListPolicy JuniIpPolicyPolicy
  juniIpCommunityListExpression OCTET STRING
  juniIpCommunityListRowStatus RowStatus

JuniIpExtCommunityListEntry  
SEQUENCE    
  juniIpExtCommunityListName JuniIpPolicyName
  juniIpExtCommunityListElemId Integer32
  juniIpExtCommunityListCreatedInternally TruthValue
  juniIpExtCommunityListPolicy JuniIpPolicyPolicy
  juniIpExtCommunityListExpression OCTET STRING
  juniIpExtCommunityListRowStatus RowStatus

JuniIpDynRedistributeEntry  
SEQUENCE    
  juniIpDynRedistributeToProtocol JuniIpDynRedistributeProtocol
  juniIpDynRedistributeState JuniIpPolicyAdminStatus
  juniIpDynRedistributeRowStatus RowStatus

JuniIpRedistributeEntry  
SEQUENCE    
  juniIpRedistributeToProtocol JuniIpRedistributeProtocol
  juniIpRedistributeFromProtocol JuniIpRedistributeProtocol
  juniIpRedistributeState JuniIpPolicyAdminStatus
  juniIpRedistributeRouteMapName JuniIpPolicyName
  juniIpRedistributeRowStatus RowStatus

JuniIpRouteMapEntry  
SEQUENCE    
  juniIpRouteMapName JuniIpPolicyName
  juniIpRouteMapSequenceNum Integer32
  juniIpRouteMapElemId Integer32
  juniIpRouteMapSubElemId Integer32
  juniIpRouteMapCreatedInternally TruthValue
  juniIpRouteMapPolicy JuniIpPolicyPolicy
  juniIpRouteMapDisplay OCTET STRING

JuniIpRouteMapV2Entry  
SEQUENCE    
  juniIpRouteMapV2Name JuniIpPolicyName
  juniIpRouteMapV2SequenceNum Integer32
  juniIpRouteMapV2Policy JuniIpPolicyPolicy
  juniIpRouteMapV2RowStatus RowStatus

JuniIpRouteMapClauseEntry  
SEQUENCE    
  juniIpRouteMapClauseElemId INTEGER
  juniIpRouteMapClauseSubElemId Integer32
  juniIpRouteMapClauseElemIdAddon INTEGER
  juniIpRouteMapClauseElementValue DisplayString
  juniIpRouteMapClauseRowStatus RowStatus

Defined Values

juniIpPolicyMIB 1.3.6.1.4.1.4874.2.2.13
The IP Policy MIB for the Juniper Networks enterprise.
MODULE-IDENTITY    

juniIpPolicyObjects 1.3.6.1.4.1.4874.2.2.13.1
OBJECT IDENTIFIER    

juniIpAccessList 1.3.6.1.4.1.4874.2.2.13.1.1
OBJECT IDENTIFIER    

juniIpNamedAccessList 1.3.6.1.4.1.4874.2.2.13.1.2
OBJECT IDENTIFIER    

juniIpAspAccessList 1.3.6.1.4.1.4874.2.2.13.1.3
OBJECT IDENTIFIER    

juniIpPrefixList 1.3.6.1.4.1.4874.2.2.13.1.4
OBJECT IDENTIFIER    

juniIpPrefixTree 1.3.6.1.4.1.4874.2.2.13.1.5
OBJECT IDENTIFIER    

juniIpCommunityList 1.3.6.1.4.1.4874.2.2.13.1.6
OBJECT IDENTIFIER    

juniIpRedistributeList 1.3.6.1.4.1.4874.2.2.13.1.7
OBJECT IDENTIFIER    

juniIpRouteMapTree 1.3.6.1.4.1.4874.2.2.13.1.8
OBJECT IDENTIFIER    

juniIpAccessListTable 1.3.6.1.4.1.4874.2.2.13.1.1.1
This table contains entries for elements of IP access lists. Entries belonging to the same access list are ordered, and comparisons to those entries are performed in that order until a match is detected. If no match is found, the default action is to 'deny'.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniIpAccessListEntry

juniIpAccessListEntry 1.3.6.1.4.1.4874.2.2.13.1.1.1.1
Each entry describes the characteristics of an IP access list element.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniIpAccessListEntry  

juniIpAccessListId 1.3.6.1.4.1.4874.2.2.13.1.1.1.1.1
The number of the access list to which this entry belongs.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..10000  

juniIpAccessListElemId 1.3.6.1.4.1.4874.2.2.13.1.1.1.1.2
The relative position of this entry within its access list. Access list entries are searched in this sequence (low to high values) until a match is found. NOTE: The value zero is reserved for use with SET operations to perform special-purpose table entry creations/deletions; see the DESCRIPTION of juniIpAccessListRowStatus for details. Get/GetNext/GetBulk retrievals never return an entry for which this object is zero-valued.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..10000  

juniIpAccessListRowStatus 1.3.6.1.4.1.4874.2.2.13.1.1.1.1.3
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy Two configuration levels are defined, limited and full. EARLY IMPLEMENTATIONS MIGHT PROVIDE ONLY THE LIMITED LEVEL OF CONFIGURATION CAPABILITY. *** LIMITED ACCESS LIST CONFIGURATION LEVEL *** 1) RowStatus createAndGo/destroy operations directed to a target table entry for which juniIpAccessListElemId is ZERO, have the following special-purpose semantics: createAndGo Create an entry having the specified configuration and append it to the target list, i.e. assign it a value of juniIpAccessListElemId that is one greater than the current last element in the list. destroy Destroy the specified list and all of its constituent elements. 2) RowStatus createAndGo/destroy operations directed to a target table entry for which juniIpAccessListElemId is NONZERO are disallowed. *** FULL ACCESS LIST CONFIGURATION LEVEL *** Permit conventional RowStatus-based management of table entries having a nonzero value for juniIpAccessListElemId, IN ADDITION TO the special RowStatus semantics applied to entries having a zero value for juniIpAccessListElemId. To create an entry in this table, the following entry objects MUST be explicitly configured: juniIpAccessListRowStatus In addition, when creating an entry the following conditions must hold: The value of juniIpAccessListElemId is nonzero. Once created, element attributes cannot be modified except by a RowStatus destroy operation to delete the list element.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

juniIpAccessListAction 1.3.6.1.4.1.4874.2.2.13.1.1.1.1.4
Specifies the disposition of an item that matches the comparison criteria described by this entry.
Status: current Access: read-create
OBJECT-TYPE    
  JuniIpPolicyPolicy  

juniIpAccessListSrc 1.3.6.1.4.1.4874.2.2.13.1.1.1.1.5
A source IP address. A subject IP address is first masked with the value of juniIpAccessListSrcMask, then the result is compared to this value. Setting both this object and its corresponding mask to 0.0.0.0 acts as a wildcard, matching any source IP address.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

juniIpAccessListSrcMask 1.3.6.1.4.1.4874.2.2.13.1.1.1.1.6
The IP address mask to be applied to a subject source IP address before comparing it to juniIpAccessListSrc. Ones in the mask identify which bits in the subject IP address are significant for the comparison. To be considered valid, a nonzero value for this object must contain a single contiguous string of ones, beginning with the most significant bit of the mask.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

juniIpAccessListDst 1.3.6.1.4.1.4874.2.2.13.1.1.1.1.7
A destination IP address. A subject IP address is first masked with the value of juniIpAccessListDstMask, then the result is compared to this value. Setting both this object and its corresponding mask to 0.0.0.0 acts as a wildcard, matching any destination IP address.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

juniIpAccessListDstMask 1.3.6.1.4.1.4874.2.2.13.1.1.1.1.8
The IP address mask to be applied to a subject destination IP address before comparing it to juniIpAccessListDst. Ones in the mask identify which bits in the IP address are significant for the comparison. To be considered valid, a nonzero value for this object must contain a single contiguous string of ones, beginning with the most significant bit of the mask.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

juniIpAccessListProtocol 1.3.6.1.4.1.4874.2.2.13.1.1.1.1.9
An IP Protocol value. Nonzero values match a specific IP Protocol value (e.g. 6 for TCP) carried in an IP packet; a value of zero acts as a wildcard, matching any IP Protocol.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..255  

juniIpNamedAccessListTable 1.3.6.1.4.1.4874.2.2.13.1.2.1
This table contains entries for elements of IP access lists. Entries belonging to the same access list are ordered, and comparisons to those entries are performed in that order until a match is detected. If no match is found, the default action is to 'deny'.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniIpNamedAccessListEntry

juniIpNamedAccessListEntry 1.3.6.1.4.1.4874.2.2.13.1.2.1.1
Each entry describes the characteristics of an IP access list element.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniIpNamedAccessListEntry  

juniIpNamedAccessListName 1.3.6.1.4.1.4874.2.2.13.1.2.1.1.1
The name of the access list to which this entry belongs.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniIpPolicyName  

juniIpNamedAccessListElemId 1.3.6.1.4.1.4874.2.2.13.1.2.1.1.2
The relative position of this entry within its access list. Access list entries are searched in this sequence (low to high values) until a match is found. NOTE: The value zero is reserved for use with SET operations to perform special-purpose table entry creations/deletions; see the DESCRIPTION of juniIpNamedAccessListRowStatus for details. Get/GetNext/GetBulk retrievals never return an entry for which this object is zero-valued.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..10000  

juniIpNamedAccessListRowStatus 1.3.6.1.4.1.4874.2.2.13.1.2.1.1.3
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy Two configuration levels are defined, limited and full. EARLY IMPLEMENTATIONS MIGHT PROVIDE ONLY THE LIMITED LEVEL OF CONFIGURATION CAPABILITY. *** LIMITED ACCESS LIST CONFIGURATION LEVEL *** 1) RowStatus createAndGo/destroy operations directed to a target table entry for which juniIpNamedAccessListElemId is ZERO, have the following special-purpose semantics: createAndGo Create an entry having the specified configuration and append it to the target list, i.e. assign it a value of juniIpNamedAccessListElemId that is one greater than the current last element in the list. destroy Destroy the specified list and all of its constituent elements. 2) RowStatus createAndGo/destroy operations directed to a target table entry for which juniIpNamedAccessListElemId is NONZERO are disallowed. *** FULL ACCESS LIST CONFIGURATION LEVEL *** Permit conventional RowStatus-based management of table entries having a nonzero value for juniIpNamedAccessListElemId, IN ADDITION TO the special RowStatus semantics applied to entries having a zero value for juniIpNamedAccessListElemId. To create an entry in this table, the following entry objects MUST be explicitly configured: juniIpNamedAccessListRowStatus In addition, when creating an entry the following conditions must hold: The value of juniIpNamedAccessListElemId is nonzero. Once created, element attributes cannot be modified except by a RowStatus destroy operation to delete the list element.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

juniIpNamedAccessListAction 1.3.6.1.4.1.4874.2.2.13.1.2.1.1.4
Specifies the disposition of an item that matches the comparison criteria described by this entry.
Status: current Access: read-create
OBJECT-TYPE    
  JuniIpPolicyPolicy  

juniIpNamedAccessListSrc 1.3.6.1.4.1.4874.2.2.13.1.2.1.1.5
A source IP address. A subject IP address is first masked with the value of juniIpNamedAccessListSrcMask, then the result is compared to this value. Setting both this object and its corresponding mask to 0.0.0.0 acts as a wildcard, matching any source IP address.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

juniIpNamedAccessListSrcMask 1.3.6.1.4.1.4874.2.2.13.1.2.1.1.6
The IP address mask to be applied to a subject source IP address before comparing it to juniIpNamedAccessListSrc. Ones in the mask identify which bits in the subject IP address are significant for the comparison. To be considered valid, a nonzero value for this object must contain a single contiguous string of ones, beginning with the most significant bit of the mask.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

juniIpNamedAccessListDst 1.3.6.1.4.1.4874.2.2.13.1.2.1.1.7
A destination IP address. A subject IP address is first masked with the value of juniIpNamedAccessListDstMask, then the result is compared to this value. Setting both this object and its corresponding mask to 0.0.0.0 acts as a wildcard, matching any destination IP address.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

juniIpNamedAccessListDstMask 1.3.6.1.4.1.4874.2.2.13.1.2.1.1.8
The IP address mask to be applied to a subject destination IP address before comparing it to juniIpNamedAccessListDst. Ones in the mask identify which bits in the IP address are significant for the comparison. To be considered valid, a nonzero value for this object must contain a single contiguous string of ones, beginning with the most significant bit of the mask.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

juniIpNamedAccessListProtocol 1.3.6.1.4.1.4874.2.2.13.1.2.1.1.9
An IP Protocol value. Nonzero values match a specific IP Protocol value (e.g. 6 for TCP) carried in an IP packet; a value of zero acts as a wildcard, matching any IP Protocol.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..255  

juniIpAspAccessTable 1.3.6.1.4.1.4874.2.2.13.1.3.1
This table contains entries for elements of IP AS-Path access entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniIpAspAccessEntry

juniIpAspAccessEntry 1.3.6.1.4.1.4874.2.2.13.1.3.1.1
Each entry describes the characteristics of an IP AS-Path access element.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniIpAspAccessEntry  

juniIpAspAccessName 1.3.6.1.4.1.4874.2.2.13.1.3.1.1.1
The name of the AS-Path Access List to which this entry belongs.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniIpPolicyName  

juniIpAspAccessElemId 1.3.6.1.4.1.4874.2.2.13.1.3.1.1.2
The element ID portion of the IP AS-Path for this entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..10000  

juniIpAspAccessCreatedInternally 1.3.6.1.4.1.4874.2.2.13.1.3.1.1.3
Indicated whether this entry was created internally by the system, or dynamically via a management interface. A true value for this object indicates that this entry was created internally; false indicates externally.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniIpAspAccessPolicy 1.3.6.1.4.1.4874.2.2.13.1.3.1.1.4
Indicates the action to take for this AS-Path access list.
Status: current Access: read-create
OBJECT-TYPE    
  JuniIpPolicyPolicy  

juniIpAspAccessExpression 1.3.6.1.4.1.4874.2.2.13.1.3.1.1.5
The AS-Path access list expression for this entry.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(1..256)  

juniIpAspAccessRowStatus 1.3.6.1.4.1.4874.2.2.13.1.3.1.1.6
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniIpCommunityRowStatus In addition, when creating an entry the following conditions must hold: Once created, only certain attributes can be modified.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

juniIpPrefixListTable 1.3.6.1.4.1.4874.2.2.13.1.4.1
This table contains entries for elements of IP prefix lists. Entries belonging to the same prefix list are ordered, and comparisons to those entries are performed in that order until a match is detected. If no match is found, the default action is to 'deny'.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniIpPrefixListEntry

juniIpPrefixListEntry 1.3.6.1.4.1.4874.2.2.13.1.4.1.1
Each entry describes the characteristics of an IP prefix list element.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniIpPrefixListEntry  

juniIpPrefixListName 1.3.6.1.4.1.4874.2.2.13.1.4.1.1.1
The name of the prefix list to which this entry belongs.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniIpPolicyName  

juniIpPrefixListElemId 1.3.6.1.4.1.4874.2.2.13.1.4.1.1.2
The relative position of this entry within its prefix list. Access list entries are searched in this sequence (low to high values) until a match is found.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..10000  

juniIpPrefixListIpAddress 1.3.6.1.4.1.4874.2.2.13.1.4.1.1.3
The IP Address portion of the IP List value for this entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

juniIpPrefixListLength 1.3.6.1.4.1.4874.2.2.13.1.4.1.1.4
The length portion of the IP List value for this entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..32  

juniIpPrefixListPolicy 1.3.6.1.4.1.4874.2.2.13.1.4.1.1.5
The IP Prefix list action to perform for this entry.
Status: current Access: read-create
OBJECT-TYPE    
  JuniIpPolicyPolicy  

juniIpPrefixListGeValue 1.3.6.1.4.1.4874.2.2.13.1.4.1.1.6
The minimum prefix length to apply to address.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..32  

juniIpPrefixListLeValue 1.3.6.1.4.1.4874.2.2.13.1.4.1.1.7
The maximum prefix length to apply to address.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..32  

juniIpPrefixListDescription 1.3.6.1.4.1.4874.2.2.13.1.4.1.1.8
The administratively assigned description for this entry.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

juniIpPrefixListHitCount 1.3.6.1.4.1.4874.2.2.13.1.4.1.1.9
The number of hits for this entry.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

juniIpPrefixListRowStatus 1.3.6.1.4.1.4874.2.2.13.1.4.1.1.10
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniIpPrefixListRowStatus In addition, when creating an entry the following conditions must hold: The value of juniIpPrefixListElemId is nonzero. Once created, only certain attributes can be modified.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

juniIpPrefixTreeTable 1.3.6.1.4.1.4874.2.2.13.1.5.1
This table contains entries for elements of IP prefix trees. Entries belonging to the same prefix tree are ordered, and comparisons to those entries are performed in that order until a match is detected. If no match is found, the default action is to 'deny'.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniIpPrefixTreeEntry

juniIpPrefixTreeEntry 1.3.6.1.4.1.4874.2.2.13.1.5.1.1
Each entry describes the characteristics of an IP prefix tree element.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniIpPrefixTreeEntry  

juniIpPrefixTreeName 1.3.6.1.4.1.4874.2.2.13.1.5.1.1.1
The name of the prefix tree to which this entry belongs.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniIpPolicyName  

juniIpPrefixTreeIpAddress 1.3.6.1.4.1.4874.2.2.13.1.5.1.1.2
The IP Address portion of the IP Prefix value for this entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

juniIpPrefixTreeLength 1.3.6.1.4.1.4874.2.2.13.1.5.1.1.3
The length portion of the IP Prefix value for this entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..32  

juniIpPrefixTreePolicy 1.3.6.1.4.1.4874.2.2.13.1.5.1.1.4
The IP Prefix tree policy perform for this entry.
Status: current Access: read-create
OBJECT-TYPE    
  JuniIpPolicyPolicy  

juniIpPrefixTreeDescription 1.3.6.1.4.1.4874.2.2.13.1.5.1.1.5
The administratively assigned description for this entry.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

juniIpPrefixTreeHitCount 1.3.6.1.4.1.4874.2.2.13.1.5.1.1.6
The number of hits for this entry.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

juniIpPrefixTreeRowStatus 1.3.6.1.4.1.4874.2.2.13.1.5.1.1.7
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniIpPrefixTreeRowStatus In addition, when creating an entry the following conditions must hold: The value of juniIpPrefixTreeIpAddress and juniIpPrefixTreeLength are nonzero. Once created, only certain attributes can be modified.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

juniIpCommunityListTable 1.3.6.1.4.1.4874.2.2.13.1.6.1
This table contains entries for elements of IP Community Lists. Entries belonging to the same Community List are ordered. The table supports standard and extended community lists.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniIpCommunityListEntry

juniIpCommunityListEntry 1.3.6.1.4.1.4874.2.2.13.1.6.1.1
Each entry describes the characteristics of an IP Community List element.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniIpCommunityListEntry  

juniIpCommunityListName 1.3.6.1.4.1.4874.2.2.13.1.6.1.1.1
The name of the Community List to which this entry belongs.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniIpPolicyName  

juniIpCommunityListElemId 1.3.6.1.4.1.4874.2.2.13.1.6.1.1.2
The IP Address portion of the IP Prefix value for this entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..10000  

juniIpCommunityListCreatedInternally 1.3.6.1.4.1.4874.2.2.13.1.6.1.1.3
Indicated whether this entry was created internally by the system, or dynamically via a management interface. A true value for this object indicates that this entry was created internally; false indicates externally.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniIpCommunityListExtended 1.3.6.1.4.1.4874.2.2.13.1.6.1.1.4
Indicates whether this entry is a standard or extended Community List. True indicates extended, false indicates standard
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniIpCommunityListPolicy 1.3.6.1.4.1.4874.2.2.13.1.6.1.1.5
Indicates the policy action to perform for this list.
Status: current Access: read-create
OBJECT-TYPE    
  JuniIpPolicyPolicy  

juniIpCommunityListExpression 1.3.6.1.4.1.4874.2.2.13.1.6.1.1.6
The community list expression for this entry.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(1..256)  

juniIpCommunityListRowStatus 1.3.6.1.4.1.4874.2.2.13.1.6.1.1.7
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniIpCommunityRowStatus In addition, when creating an entry the following conditions must hold: Once created, only certain attributes can be modified.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

juniIpExtCommunityListTable 1.3.6.1.4.1.4874.2.2.13.1.6.2
This table contains entries for Extended IP Community Lists. Entries belonging to the same Extended Community List are ordered.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniIpExtCommunityListEntry

juniIpExtCommunityListEntry 1.3.6.1.4.1.4874.2.2.13.1.6.2.1
Each entry describes the characteristics of an Extended IP Community List element.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniIpExtCommunityListEntry  

juniIpExtCommunityListName 1.3.6.1.4.1.4874.2.2.13.1.6.2.1.1
The name of the Extended Community List to which this entry belongs.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniIpPolicyName  

juniIpExtCommunityListElemId 1.3.6.1.4.1.4874.2.2.13.1.6.2.1.2
The element ID value for this entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..10000  

juniIpExtCommunityListCreatedInternally 1.3.6.1.4.1.4874.2.2.13.1.6.2.1.3
Indicated whether this entry was created internally by the system, or dynamically via a management interface. A true value for this object indicates that this entry was created internally; false indicates externally.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniIpExtCommunityListPolicy 1.3.6.1.4.1.4874.2.2.13.1.6.2.1.4
Indicates the policy action to perform for this list.
Status: current Access: read-create
OBJECT-TYPE    
  JuniIpPolicyPolicy  

juniIpExtCommunityListExpression 1.3.6.1.4.1.4874.2.2.13.1.6.2.1.5
The extended community list expression for this entry.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(8..256)  

juniIpExtCommunityListRowStatus 1.3.6.1.4.1.4874.2.2.13.1.6.2.1.6
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniIpExtCommunityRowStatus In addition, when creating an entry the following conditions must hold: The value of juniIpExtCommunityListElemId is included in this table as a key for future use. It must be the value zero. Once created, only certain attributes can be modified.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

juniIpDynRedistributeTable 1.3.6.1.4.1.4874.2.2.13.1.7.1
This table contains entries for elements of IP Dynamic Route Redistribution elements.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniIpDynRedistributeEntry

juniIpDynRedistributeEntry 1.3.6.1.4.1.4874.2.2.13.1.7.1.1
Each entry describes the characteristics of a dynamic IP Route Redistribute element.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniIpDynRedistributeEntry  

juniIpDynRedistributeToProtocol 1.3.6.1.4.1.4874.2.2.13.1.7.1.1.1
Identifies the protocol associated with this Dynamic Route Redistribution element that routes are redistributed to.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniIpDynRedistributeProtocol  

juniIpDynRedistributeState 1.3.6.1.4.1.4874.2.2.13.1.7.1.1.2
Indicates the enable/disable state of this redistribution element.
Status: current Access: read-create
OBJECT-TYPE    
  JuniIpPolicyAdminStatus  

juniIpDynRedistributeRowStatus 1.3.6.1.4.1.4874.2.2.13.1.7.1.1.3
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniIpDynRedistributeRowStatus Once created, only the juniIpDynRedistributeState object can be modified.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

juniIpRedistributeTable 1.3.6.1.4.1.4874.2.2.13.1.7.2
This table contains entries for elements of IP Route Redistribution elements.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniIpRedistributeEntry

juniIpRedistributeEntry 1.3.6.1.4.1.4874.2.2.13.1.7.2.1
Each entry describes the characteristics of an IP Route Redistribution element.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniIpRedistributeEntry  

juniIpRedistributeToProtocol 1.3.6.1.4.1.4874.2.2.13.1.7.2.1.1
Identifies the protocol for this element that routes are redistributed to.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniIpRedistributeProtocol  

juniIpRedistributeFromProtocol 1.3.6.1.4.1.4874.2.2.13.1.7.2.1.2
Identifies the protocol for this element that routes are redistributed from.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniIpRedistributeProtocol  

juniIpRedistributeState 1.3.6.1.4.1.4874.2.2.13.1.7.2.1.3
Indicates the enable/disable state of this redistribution element.
Status: current Access: read-create
OBJECT-TYPE    
  JuniIpPolicyAdminStatus  

juniIpRedistributeRouteMapName 1.3.6.1.4.1.4874.2.2.13.1.7.2.1.4
Identifies the IP route-map associated with this IP Route Redistribution element.
Status: current Access: read-create
OBJECT-TYPE    
  JuniIpPolicyName  

juniIpRedistributeRowStatus 1.3.6.1.4.1.4874.2.2.13.1.7.2.1.5
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniIpRedistributeRowStatus juniIpRedistributeRouteMapName Once created, only the juniIpRedistributeState object can be modified.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

juniIpRouteMapTable 1.3.6.1.4.1.4874.2.2.13.1.8.1
This table contains entries for elements of IP Route Maps.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniIpRouteMapEntry

juniIpRouteMapEntry 1.3.6.1.4.1.4874.2.2.13.1.8.1.1
Each entry describes the characteristics of an IP Route Map element.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniIpRouteMapEntry  

juniIpRouteMapName 1.3.6.1.4.1.4874.2.2.13.1.8.1.1.1
The name of the route map to which this entry belongs.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniIpPolicyName  

juniIpRouteMapSequenceNum 1.3.6.1.4.1.4874.2.2.13.1.8.1.1.2
The element ID value for this entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..2147483647  

juniIpRouteMapElemId 1.3.6.1.4.1.4874.2.2.13.1.8.1.1.3
The element ID to which this entry belongs.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..2147483647  

juniIpRouteMapSubElemId 1.3.6.1.4.1.4874.2.2.13.1.8.1.1.4
The sub-element ID to which this entry belongs.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..2147483647  

juniIpRouteMapCreatedInternally 1.3.6.1.4.1.4874.2.2.13.1.8.1.1.5
Indicated whether this entry was created internally by the system, or dynamically via a management interface. A true value for this object indicates that this entry was created internally; false indicates externally.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniIpRouteMapPolicy 1.3.6.1.4.1.4874.2.2.13.1.8.1.1.6
Indicates the policy action performed by this element.
Status: current Access: read-only
OBJECT-TYPE    
  JuniIpPolicyPolicy  

juniIpRouteMapDisplay 1.3.6.1.4.1.4874.2.2.13.1.8.1.1.7
Textual information taken from the NVT ASCII character set (i.e. RFC1903 DisplayString), but with increased length. The information in this object is the series of set, match, and/or match & set clauses for this route map. It is assumed that the information conveyed in this object is used for display purposes and in general, is not parsed. The information in this string is a concatentation of routemap clauses configured via the systems non SNMP interface.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..2048)  

juniIpRouteMapV2Table 1.3.6.1.4.1.4874.2.2.13.1.8.2
This table contains entries for route maps instances.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniIpRouteMapV2Entry

juniIpRouteMapV2Entry 1.3.6.1.4.1.4874.2.2.13.1.8.2.1
Each entry is a specific instance of the Route Map.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniIpRouteMapV2Entry  

juniIpRouteMapV2Name 1.3.6.1.4.1.4874.2.2.13.1.8.2.1.1
The name of the route map to which this instance entry belongs.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniIpPolicyName  

juniIpRouteMapV2SequenceNum 1.3.6.1.4.1.4874.2.2.13.1.8.2.1.2
Multiple instances of the same route map can be created by assigning a different sequence number to it. Each instance is identified by the route map name and the sequence number. The value of the sequence number associated with the particular route map instance determines the order in which the routing protocol evaluates routes; the instance of having lowest sequence number is evaluated first. If the routes pass all the match conditions specified in the lowest-numbered instance, and if all set clause elements are successfully configured, then no other instance of the route map is considered. However, any routes that do not pass all the match conditions are evaluated against the next instance of the route map.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2147483647  

juniIpRouteMapV2Policy 1.3.6.1.4.1.4874.2.2.13.1.8.2.1.3
Indicates the policy action performed by this route map instance.
Status: current Access: read-create
OBJECT-TYPE    
  JuniIpPolicyPolicy  

juniIpRouteMapV2RowStatus 1.3.6.1.4.1.4874.2.2.13.1.8.2.1.4
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniIpRouteMapV2RowStatus To delete an entry in this table, the following entry objects MUST be explicitly configured: juniIpRouteMapV2RowStatus Once created, juniIpRouteMapV2Policy attribute can be modified. To modify juniIpRouteMapV2Policy, set juniIpRouteMapV2RowStatus also. Note: Match, match-set and set clause elements can be configured for a specific instance of the route map. First create the route map instance to make use of the same to configure in the clause table. Deletion of the route map instance will also delete all the clause elements confgured for that instance as clause elements are configured for that instance.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

juniIpRouteMapClauseTable 1.3.6.1.4.1.4874.2.2.13.1.8.3
This table contains entries for instances of the route map clause elements.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniIpRouteMapClauseEntry

juniIpRouteMapClauseEntry 1.3.6.1.4.1.4874.2.2.13.1.8.3.1
Each entry describes the characteristics of one route map clause element instance.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniIpRouteMapClauseEntry  

juniIpRouteMapClauseElemId 1.3.6.1.4.1.4874.2.2.13.1.8.3.1.1
The clause element selection option. Select the appropriate element option to configure each element instance of match, match-set and set clauses. For the complete configuration map table refer to the juniIpRouteMapClauseRowStatus object's DESCRIPTION.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER matchNotKnown(0), matchAsPath(1), matchCommunity(2), matchExtendedCommunity(3), matchDistance(4), matchAccessList(5), matchNextHop(6), matchPrefixList(7), matchNextHopPreList(8), matchPrefixTree(9), matchNextHopPreTree(10), matchLevel(11), matchMetric(12), matchMetricType(13), matchTag(14), matchRouteType(15), matchSource(16), matchPolicyList(17), setAsPath(100), setAsPathCreateList(101), setAutoTag(102), setCommList(103), setCommunityNone(104), setCommunityAdd(105), setCommunity(106), setCommunityCreateListAdd(107), setCommunityCreateList(108), setExtendedCommunityCreateAdd(109), setExtendedCommunityCreate(110), setNextHop(111), setNextHopPeerAddr(112), setLocalPref(113), setWeight(114), setLevel(115), setMetric(116), setMetricType(117), setTag(118), setOrigin(119), setRouteType(220), setDampingCreate(221), setDistance(222), matchSetSummary(300)  

juniIpRouteMapClauseSubElemId 1.3.6.1.4.1.4874.2.2.13.1.8.3.1.2
The clause element sub ID used to distinguish specific instance of the element. This value is determined by choosing the next available by walking the table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2147483647  

juniIpRouteMapClauseElemIdAddon 1.3.6.1.4.1.4874.2.2.13.1.8.3.1.3
This represents clause element instance add-on option selected along with the main option (juniIpRouteMapClauseElemId) whenever it applies. For more information on how to map this object value to each value, refer to the mapping table in the juniIpRouteMapClauseRowStatus object's DESCRIPTION.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER notApplicable(0), exact(1), delete(2), relativeNeg(3), relativePos(4), extCommRt(5), extCommSoo(6), interfaceValue(7), ipAddress(8)  

juniIpRouteMapClauseElementValue 1.3.6.1.4.1.4874.2.2.13.1.8.3.1.4
This represents set, match-set and match clauses' different element instance values in character string form. Whatever may be the data type of the attribute element instance value, it is always interpreted as a set of characters for both configuration and display purposes. It is up to the user to know the element's data type mapping in order to input the correct value while configuring. Refer to the mapping table in the juniIpRouteMapClauseRowStatus object descrption for detailed information.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..100)  

juniIpRouteMapClauseRowStatus 1.3.6.1.4.1.4874.2.2.13.1.8.3.1.5
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create/delete an entry in this table, the following entry objects MUST be explicitly configured: juniIpRouteMapClauseElementValue juniIpRouteMapClauseRowStatus Additional object juniIpRouteMapClauseElemIdAddon may become OPTIONAL for some elements creation/deletion along with the above. Refer the mapping table below to determine which elements are required. The table entry elements may not be modified. Only create and delete are allowed. Note#1: Make sure route map(s) are created before configuring their corresponding clause elements. Note#2: The mapping table below is the extensive guide for the options, values and ranges of the table objects juniIpRouteMapClauseElemId, juniIpRouteMapClauseElemIdAddon and juniIpRouteMapClauseElementValue. Clause element configuration selection mapping table ==================================================== ClauseElemId ClauseElemIdAddon ClauseElementValue ============ ================= ================== matchAsPath notApplicable DisplayString (SIZE(1..32)) matchCommunity exact/ DisplayString (SIZE(1..32)) notApplicable matchExtendedCommunity exact/ DisplayString (SIZE(1..32)) notApplicable Note#3: At a given time only one can be configured for access list and prefix-list/trees'. matchAccessList notApplicable DisplayString (SIZE(1..32)) matchPrefixList notApplicable DisplayString (SIZE(1..32)) matchPrefixTree notApplicable DisplayString (SIZE(1..32)) matchNextHop notApplicable DisplayString (SIZE(1..32)) matchNextHopPreList notApplicable DisplayString (SIZE(1..32)) matchNextHopPreTree notApplicable DisplayString (SIZE(1..32)) Note#4: For matchLevel, matchMetricType and matchRouteType element selection choose the exact case-sensitive string to set the option. Example: For matchLevel, option levelOne, levelOneAndTwo, etc. can be set. matchLevel notApplicable { levelOne, levelOneAndTwo, levelTwo, backbone, stubArea } matchMetricType notApplicable { internal or typeOne, external or typeTwo } matchRouteType notApplicable { external, internal, internalInter, internalIntra } matchDistance notApplicable Integer32 (0..255) matchMetric notApplicable Unsigned32 matchTag notApplicable Unsigned32 matchPolicyList notApplicable DisplayString (SIZE(1..32)) setAsPath notApplicable DisplayString (SIZE(1..32)) setCommunityAdd notApplicable DisplayString (SIZE(1..32)) setCommList delete/ DisplayString (SIZE(1..32)) notApplicable setCommunity notApplicable DisplayString (SIZE(1..32)) Note#5: For below elements selection choose the exact case-sensitive string to set the option. Example: For setOrigin, egp or igp or incomplete will be the valid options to select. setAutoTag notApplicable { autoTag } setCommunityNone notApplicable { communityNone } Note#6: setCommunityCreateList and setCommunityCreateListAdd will have only one instance and all will be set in one instance of the element (either setCommunityCreateList or setCommunityCreateListAdd), i.e., all options and values will aggregate in one SubElementId. setCommunityCreateList notApplicable Unsigned32 setCommunityCreateListAdd notApplicable Unsigned32 setCommunityCreateList notApplicable { none, localAs, noAdvertise, noExport } setCommunityCreateListAdd notApplicable { none, localAs, noAdvertise, noExport } setLevel notApplicable { backbone, levelOne, levelOneAndTwo, levelTwo, stubArea } setRouteType notApplicable { external, internal, internalInter, internalIntra } setNextHopPeerAddr notApplicable { peerAddress } setMetricType notApplicable { external, internal } setOrigin notApplicable { egp, igp, incomplete } setAsPathCreateList notApplicable Interger32 (1..65535) setTag notApplicable Unsigned32 setWeight notApplicable Unsigned32 setDistance notApplicable Interger32 (1..255) setLocalPref notApplicable Unsigned32 setMetric relativeNeg/ Unsigned32 relativePos/ notApplicable Note#7: setExtendedCommunityCreate and setExtendedCommunityCreateAdd will have only one instance and all will be set in one instance of the element (either setExtendedCommunityCreate or setExtendedCommunityCreateAdd) i.e. all options and values will aggregate in one SubElementId. setExtendedCommunityCreate extCommRt/ IPADDRESS:Unsigned32 or notApplicable IPADDRESS-in-ASN:Unsigned32 setExtendedCommunityCreate extCommSoo/ IPADDRESS:Unsigned32 or notApplicable IPADDRESS-in-ASN:Unsigned32 setExtendedCommunityCreateAdd extCommRt/ IPADDRESS:Unsigned32 or notApplicable IPADDRESS-in-ASN:Unsigned32 setExtendedCommunityCreateAdd extCommSoo/ IPADDRESS:Unsigned32 notApplicable IPADDRESS-in-ASN:Unsigned32 Note#8: Damping element has only one instance at any given time. It can be deleted by just refering to the instance (elementID and subElementId) without refering the exact value; i.e., while deleting, values doesn't matter. setDampingCreate notApplicable 1. HalfLifeiTime-Interger32 (1..45) 2. RtSuppressTime-Interger32 (1..20000) 3. SuppressedRtReuseTime-Interger32 (1..20000) 4. MaxRtSuppressTime-Interger32 (1..255) 5. UnreachableRtHalfLifeTime-Interger32 (1..45) Note#9: 1, 2, 3 and 4 values are MUST values to be specified (in minutes) for route flap damping and 5th one is optional. Format for specifying the values are very rigid and strict. Always specify four MUST values. The first value shouldn't be preceded with space characters and last the value always should be followed with one space character. From first value to till last value, all the values will be separated from each other by one space character. setNextHop interfaceValue/ Unsigned32 notApplicable setNextHop ipAddress/ IPADDRESS notApplicable
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

juniIpPolicyConformance 1.3.6.1.4.1.4874.2.2.13.4
OBJECT IDENTIFIER    

juniIpPolicyCompliances 1.3.6.1.4.1.4874.2.2.13.4.1
OBJECT IDENTIFIER    

juniIpPolicyGroups 1.3.6.1.4.1.4874.2.2.13.4.2
OBJECT IDENTIFIER    

juniIpPolicyCompliance 1.3.6.1.4.1.4874.2.2.13.4.1.1
An obsolete compliance statement for entities that implement the Juniper IP Policy MIB. This statement became obsolete when support was added for the IP Named Access List.
Status: obsolete Access: read-create
MODULE-COMPLIANCE    

juniIpPolicyCompliance2 1.3.6.1.4.1.4874.2.2.13.4.1.2
An obsolete compliance statement for entities that implement the Juniper IP Policy MIB. This statement became obsolete when support was added for the IP ASP Access List, the IP Prefix List, the IP Prefix Tree, the IP Community List, the IP Extended Community List, IP Dynamic Route Redistribution, and the IP Route Map.
Status: obsolete Access: read-create
MODULE-COMPLIANCE    

juniIpPolicyCompliance3 1.3.6.1.4.1.4874.2.2.13.4.1.3
An obsolete compliance statement for entities that implement the Juniper IP Policy MIB. This statement became obsolete when support was added for the IP Route Map configurations.
Status: current Access: read-create
MODULE-COMPLIANCE    

juniIpPolicyCompliance4 1.3.6.1.4.1.4874.2.2.13.4.1.4
The compliance statement for entities that implement the Juniper IP Policy MIB.
Status: current Access: read-create
MODULE-COMPLIANCE    

juniIpAccessListGroup 1.3.6.1.4.1.4874.2.2.13.4.2.1
A collection of objects for managing IP access list capabilities in a Juniper product.
Status: current Access: read-create
OBJECT-GROUP    

juniIpNamedAccessListGroup 1.3.6.1.4.1.4874.2.2.13.4.2.2
A named collection of objects for managing IP access list capabilities in a Juniper product.
Status: current Access: read-create
OBJECT-GROUP    

juniIpAspAccessListGroup 1.3.6.1.4.1.4874.2.2.13.4.2.3
A named collection of objects for managing AS-Path access list capabilities in a Juniper product.
Status: current Access: read-create
OBJECT-GROUP    

juniIpPrefixListGroup 1.3.6.1.4.1.4874.2.2.13.4.2.4
A named collection of objects for managing Prefix list capabilities in a Juniper product.
Status: current Access: read-create
OBJECT-GROUP    

juniIpPrefixTreeGroup 1.3.6.1.4.1.4874.2.2.13.4.2.5
A named collection of objects for managing Prefix Tree capabilities in a Juniper product.
Status: current Access: read-create
OBJECT-GROUP    

juniIpCommunityListGroup 1.3.6.1.4.1.4874.2.2.13.4.2.6
A named collection of objects for managing Community List capabilities in a Juniper product.
Status: current Access: read-create
OBJECT-GROUP    

juniIpExtCommunityListGroup 1.3.6.1.4.1.4874.2.2.13.4.2.7
A named collection of objects for managing Extended Community List capabilities in a Juniper product.
Status: current Access: read-create
OBJECT-GROUP    

juniIpRedistributeGroup 1.3.6.1.4.1.4874.2.2.13.4.2.8
A collection of objects for managing IP route redistribution list capabilities in a Juniper product.
Status: current Access: read-create
OBJECT-GROUP    

juniIpRouteMapGroup 1.3.6.1.4.1.4874.2.2.13.4.2.9
A collection of objects for managing IP route map list capabilities in a Juniper product.
Status: obsolete Access: read-create
OBJECT-GROUP    

juniIpRouteMapGroup2 1.3.6.1.4.1.4874.2.2.13.4.2.10
A collection of objects for managing IP route map list capabilities in a Juniper product.
Status: current Access: read-create
OBJECT-GROUP    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor