Juniper-AAA-MIB

File: Juniper-AAA-MIB.mib (221830 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
Juniper-MIBs Juniper-TC Juniper-ROUTER-MIB
IPV6-TC

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Integer32
IpAddress Counter32 Unsigned32
Gauge32 TEXTUAL-CONVENTION DisplayString
RowStatus TruthValue MODULE-COMPLIANCE
OBJECT-GROUP juniMibs JuniName
JuniInterfaceLocationType JuniInterfaceLocationValue JuniVrfGroupName
JuniEnable juniRouterIndex Ipv6AddressPrefix
Ipv6AddressIfIdentifier Ipv6Address

Defined Types

JuniAaaDomainName  
The name of an internet domain. Represents textual information taken from the NVT ASCII character set.
TEXTUAL-CONVENTION    
  OCTET STRING Size(1..63)  

JuniAaaTunnelGroupName  
The name of a tunnel group. Represents textual information taken from the NVT ASCII character set.
TEXTUAL-CONVENTION    
  OCTET STRING Size(1..63)  

JuniAaaTunnelSwitchProfileName  
The name of a tunnel switch profile. Represents textual information taken from the NVT ASCII character set.
TEXTUAL-CONVENTION    
  OCTET STRING Size(0..64)  

JuniAaaAuthenticationMethods  
The set of configurable authentication choices. The maximum enumerated type will never be greater than 255.
TEXTUAL-CONVENTION    
  INTEGER protocolRadius(1), protocolNone(4), protocolLine(5), protocolTacacsPlus(6), protocolEnable(7)  

JuniAaaAccountingMethods  
The set of configurable accounting choices.
TEXTUAL-CONVENTION    
  INTEGER protocolRadius(1), protocolNone(4)  

JuniAddressAssignType  
The set of possible AAA address assignment sources.
TEXTUAL-CONVENTION    
  INTEGER none(0), radius(1), localPool(2), dhcp(3), user(4), application(5), localAuthenticationServer(6), notSet(7)  

JuniSubscriberState  
The set of possible AAA subscriber states, expressed as a bit map: init Initial state (transient) pending Auth/Acct or Addr Request is pending established Subscriber is authenticated deleting Deletion of subscriber is pending tunneling Subscriber is being tunneled tunnelAcct Tunnel accounting is enabled terminated Subscriber has been terminated counted Subscriber has been counted in statistics clientHandleSet Client handle is assigned to user profile sentAcctStart Start accounting record is requested More than one state bit can be active simultaneously. If no bits are set, the subscriber is in a transient initial state.
TEXTUAL-CONVENTION    
  BITS pending(0), established(1), deleting(2), tunneling(3), tunnelAcct(4), terminated(5), counted(6), clientHandleSet(7), sentAcctStart(8)  

JuniSubscriberClientType  
The set of possible AAA subscriber client types: ppp PPP client login Command line interface or SSH ip IP-based application config Locally configured client identity tunnel Tunnel e.g. L2TP other Unspecified client type
TEXTUAL-CONVENTION    
  INTEGER ppp(0), login(1), ip(2), config(3), tunnel(4), other(5)  

JuniSubscriberLocationType  
Obsolete description of the platform-dependent interpretation of a JuniAtmLocationValue object. This textual convention has been relpaced by Juniper-TC.JuniInterfaceLocationType.
TEXTUAL-CONVENTION    
  INTEGER unknown(0), slotPort(1)  

JuniSubscriberLocationValue  
Obsolete value of a platform-dependent interface location, represented as an OCTET STRING. A corresponding JuniAtmLocationType object identified the mapping of octets to location elements, e.g. 'slot.port'. This textual convention has been replaced by Juniper-TC.JuniInterfaceLocationValue.
TEXTUAL-CONVENTION    
  OCTET STRING Size(1..16)  

JuniSubscriberInterfaceValue  
Value of the sub-interface, represented as an OCTET STRING.
TEXTUAL-CONVENTION    
  OCTET STRING Size(1..16)  

JuniAaaAuthenticationSubscriberTypes  
The set of authentication subscriber types. The maximum enumerated type will never be greater than 255.
TEXTUAL-CONVENTION    
  INTEGER ppp(1), atm1483(2), ip(3), tunnel(4), radiusRelay(5), ipsec(6)  

JuniAaaAccountingSubscriberTypes  
The set of accounting subscriber types. The maximum enumerated type will never be greater than 255.
TEXTUAL-CONVENTION    
  INTEGER ppp(1), atm1483(2), ip(3), tunnel(4), radiusRelay(5), ipsec(6)  

JuniAaaAssignDomainEntry  
SEQUENCE    
  juniAaaAssignDomainName JuniAaaDomainName
  juniAaaAssignDomainRowStatus RowStatus
  juniAaaAssignDomainRouterName JuniName
  juniAaaAssignDomainLoopback Integer32
  juniAaaAssignDomainIpHint TruthValue
  juniAaaAssignDomainAtmServiceLevel INTEGER
  juniAaaAssignDomainAtmPcr Unsigned32
  juniAaaAssignDomainAtmScr Unsigned32
  juniAaaAssignDomainAtmMbs Unsigned32
  juniAaaAssignDomainOverrideUserName DisplayString
  juniAaaAssignDomainOverridePassword OCTET STRING
  juniAaaAssignDomainStripDomain TruthValue
  juniAaaAssignDomainPoolName DisplayString
  juniAaaAssignDomainLocalInterface DisplayString
  juniAaaAssignDomainIpv6RouterName JuniName
  juniAaaAssignDomainIpv6LocalInterface DisplayString
  juniAaaAssignDomainTunnelGroup JuniAaaTunnelGroupName
  juniAaaAssignDomainAuthRouterName JuniName
  juniAaaAssignDomainIpRouterName JuniName
  juniAaaAssignDomainTunnelSubscriberAuthentication TruthValue
  juniAaaAssignDomainBackupPoolName DisplayString

JuniAaaAssignDomainTunnelEntry  
SEQUENCE    
  juniAaaAssignDomainTunnelName JuniAaaDomainName
  juniAaaAssignDomainTunnelTag Integer32
  juniAaaAssignDomainTunnelPreference Integer32
  juniAaaAssignDomainTunnelType INTEGER
  juniAaaAssignDomainTunnelMedium INTEGER
  juniAaaAssignDomainTunnelAddress DisplayString
  juniAaaAssignDomainTunnelPassword DisplayString
  juniAaaAssignDomainTunnelId DisplayString
  juniAaaAssignDomainTunnelHostName DisplayString
  juniAaaAssignDomainTunnelRowStatus RowStatus
  juniAaaAssignDomainTunnelServerName DisplayString
  juniAaaAssignDomainTunnelClientAddress DisplayString
  juniAaaAssignDomainTunnelMaxSessions Unsigned32
  juniAaaAssignDomainTunnelReceiveWindowSize Integer32
  juniAaaAssignDomainTunnelFailoverResync INTEGER
  juniAaaAssignDomainTunnelSwitchProfile JuniAaaTunnelSwitchProfileName
  juniAaaAssignDomainTunnelTxConnectSpeedMethod INTEGER

JuniAaaAssignDomainPadnEntry  
SEQUENCE    
  juniAaaAssignDomainPadnIpAddress IpAddress
  juniAaaAssignDomainPadnIpMask IpAddress
  juniAaaAssignDomainPadnRowStatus RowStatus
  juniAaaAssignDomainPadnDistance Integer32

JuniAaaTunnelGroupEntry  
SEQUENCE    
  juniAaaTunnelGroupName JuniAaaTunnelGroupName
  juniAaaTunnelGroupRowStatus RowStatus

JuniAaaTunnelGroupTunnelEntry  
SEQUENCE    
  juniAaaTunnelGroupTunnelName JuniAaaTunnelGroupName
  juniAaaTunnelGroupTunnelTag Integer32
  juniAaaTunnelGroupTunnelPreference Integer32
  juniAaaTunnelGroupTunnelType INTEGER
  juniAaaTunnelGroupTunnelMedium INTEGER
  juniAaaTunnelGroupTunnelAddress DisplayString
  juniAaaTunnelGroupTunnelPassword DisplayString
  juniAaaTunnelGroupTunnelId DisplayString
  juniAaaTunnelGroupTunnelHostName DisplayString
  juniAaaTunnelGroupTunnelRowStatus RowStatus
  juniAaaTunnelGroupTunnelServerName DisplayString
  juniAaaTunnelGroupTunnelClientAddress DisplayString
  juniAaaTunnelGroupTunnelMaxSessions Integer32
  juniAaaTunnelGroupTunnelReceiveWindowSize Integer32
  juniAaaTunnelGroupTunnelRouterName JuniName
  juniAaaTunnelGroupTunnelFailoverResync INTEGER
  juniAaaTunnelGroupTunnelSwitchProfile JuniAaaTunnelSwitchProfileName
  juniAaaTunnelGroupTunnelTxConnectSpeedMethod INTEGER

JuniAaaAuthMethodsEntry  
SEQUENCE    
  juniAaaAuthMethodsSubscriberType JuniAaaAuthenticationSubscriberTypes
  juniAaaAuthMethodsAuthentication OCTET STRING

JuniAaaLocalAuthUserEntry  
SEQUENCE    
  juniAaaLocalAuthUserName DisplayString
  juniAaaLocalAuthUserRowStatus RowStatus
  juniAaaLocalAuthUserPassword OCTET STRING
  juniAaaLocalAuthUserEncryption INTEGER
  juniAaaLocalAuthUserIpAddress IpAddress
  juniAaaLocalAuthUserIpAddressPool DisplayString
  juniAaaLocalAuthUserRouterName JuniName

JuniAaaLocalAuthUserDbEntry  
SEQUENCE    
  juniAaaLocalAuthUserDbName DisplayString
  juniAaaLocalAuthUserDbRowStatus RowStatus

JuniAaaLocalAuthUserDbAssocEntry  
SEQUENCE    
  juniAaaLocalAuthUserDbAssocRowStatus RowStatus
  juniAaaLocalAuthUserDbAssocDbName DisplayString

JuniAaaAcctMethodsEntry  
SEQUENCE    
  juniAaaAcctMethodsSubscriberType JuniAaaAccountingSubscriberTypes
  juniAaaAcctMethodsAccounting OCTET STRING

JuniAaaAcctBcastServerGroupEntry  
SEQUENCE    
  juniAaaAcctBcastServerGroup JuniVrfGroupName
  juniAaaAcctBcastServerGroupRouter1 JuniName
  juniAaaAcctBcastServerGroupRouter2 JuniName
  juniAaaAcctBcastServerGroupRouter3 JuniName
  juniAaaAcctBcastServerGroupRouter4 JuniName
  juniAaaAcctBcastServerGroupRowStatus RowStatus

JuniAaaSubscriberEntry  
SEQUENCE    
  juniAaaSubscriberHandle Unsigned32
  juniAaaSubscriberUserName DisplayString
  juniAaaSubscriberRouterName JuniName
  juniAaaSubscriberRouterIndex Unsigned32
  juniAaaSubscriberLoginTime DisplayString
  juniAaaSubscriberIpAddress IpAddress
  juniAaaSubscriberIpAddressMask IpAddress
  juniAaaSubscriberAddrAssignType JuniAddressAssignType
  juniAaaSubscriberInterfaceId DisplayString
  juniAaaSubscriberState JuniSubscriberState
  juniAaaSubscriberClientType JuniSubscriberClientType
  juniAaaSubscriberIngressPolicyName DisplayString
  juniAaaSubscriberEgressPolicyName DisplayString
  juniAaaSubscriberQosProfileName DisplayString
  juniAaaSubscriberRowStatus RowStatus
  juniAaaSubscriberIpv6RouterIndex Unsigned32
  juniAaaSubscriberIpv6AddrIfIdentifier Ipv6AddressIfIdentifier

JuniAaaSubscriberRouterSummaryEntry  
SEQUENCE    
  juniAaaSubscriberRouterSummaryRouterIndex Unsigned32
  juniAaaSubscriberRouterSummaryCount Gauge32

JuniAaaSubscriberRouterEntry  
SEQUENCE    
  juniAaaSubscriberRouterRouterIndex Unsigned32
  juniAaaSubscriberRouterHandle Unsigned32
  juniAaaSubscriberRouterRowStatus RowStatus

JuniAaaSubscriberLocationSummaryEntry  
SEQUENCE    
  juniAaaSubscriberLocationSummaryLocationIndex JuniInterfaceLocationValue
  juniAaaSubscriberLocationSummaryCount Gauge32

JuniAaaSubscriberLocationEntry  
SEQUENCE    
  juniAaaSubscriberLocationLocationIndex JuniInterfaceLocationValue
  juniAaaSubscriberLocationHandle Unsigned32
  juniAaaSubscriberLocationRowStatus RowStatus

JuniAaaSubscriberIpv6AddrPrefixEntry  
SEQUENCE    
  juniAaaSubscriberIpv6AddrPrefix Ipv6AddressPrefix
  juniAaaSubscriberIpv6AddrPrefixSize Integer32

JuniAaaSubscriberInterfaceSummaryEntry  
SEQUENCE    
  juniAaaSubscriberInterfaceSummaryIndex JuniSubscriberInterfaceValue
  juniAaaSubscriberSubInterfaceSummaryIndex Integer32
  juniAaaSubscriberInterfaceSummaryCount Gauge32

JuniAaaSubscriberInterfaceEntry  
SEQUENCE    
  juniAaaSubscriberInterfaceIndex JuniSubscriberInterfaceValue
  juniAaaSubscriberSubInterfaceIndex Integer32
  juniAaaSubscriberInterfaceHandle Unsigned32
  juniAaaSubscriberInterfaceRowStatus RowStatus

JuniAaaSubscriberSlotSummaryEntry  
SEQUENCE    
  juniAaaSubscriberSlotSummarySlotIndex Unsigned32
  juniAaaSubscriberSlotSummaryCount Gauge32

JuniAaaSubscriberSlotEntry  
SEQUENCE    
  juniAaaSubscriberSlotIndex Unsigned32
  juniAaaSubscriberSlotHandle Unsigned32
  juniAaaSubscriberSlotRowStatus RowStatus

JuniAaaSubscriberExtEntry  
SEQUENCE    
  juniAaaSubscriberExtUserName DisplayString
  juniAaaSubscriberExtLoginTime DisplayString
  juniAaaSubscriberExtIpAddress IpAddress
  juniAaaSubscriberExtIpAddressMask IpAddress
  juniAaaSubscriberExtAddrAssignType JuniAddressAssignType
  juniAaaSubscriberExtState JuniSubscriberState
  juniAaaSubscriberExtClientType JuniSubscriberClientType
  juniAaaSubscriberExtAcctSessionId DisplayString
  juniAaaSubscriberExtClass DisplayString
  juniAaaSubscriberExtNasPort Unsigned32
  juniAaaSubscriberExtNasPortType Unsigned32
  juniAaaSubscriberExtCalledStationId OCTET STRING
  juniAaaSubscriberExtCallingStationId OCTET STRING
  juniAaaSubscriberExtL2tpTunnelId Integer32

Defined Values

juniAaaMIB 1.3.6.1.4.1.4874.2.2.20
The Authentication, Authorization and Accounting (AAA) MIB for the Juniper Networks enterprise.
MODULE-IDENTITY    

juniAaaObjects 1.3.6.1.4.1.4874.2.2.20.1
OBJECT IDENTIFIER    

juniAaaAssignment 1.3.6.1.4.1.4874.2.2.20.1.1
OBJECT IDENTIFIER    

juniAaaAuthentication 1.3.6.1.4.1.4874.2.2.20.1.2
OBJECT IDENTIFIER    

juniAaaAccounting 1.3.6.1.4.1.4874.2.2.20.1.3
OBJECT IDENTIFIER    

juniAaaAddress 1.3.6.1.4.1.4874.2.2.20.1.4
OBJECT IDENTIFIER    

juniAaaStatistics 1.3.6.1.4.1.4874.2.2.20.1.5
OBJECT IDENTIFIER    

juniAaaTimeout 1.3.6.1.4.1.4874.2.2.20.1.6
OBJECT IDENTIFIER    

juniAaaTunnel 1.3.6.1.4.1.4874.2.2.20.1.7
OBJECT IDENTIFIER    

juniAaaSubscribers 1.3.6.1.4.1.4874.2.2.20.1.8
OBJECT IDENTIFIER    

juniAaaCapabilities 1.3.6.1.4.1.4874.2.2.20.1.9
OBJECT IDENTIFIER    

juniAaaAssignGeneral 1.3.6.1.4.1.4874.2.2.20.1.1.1
OBJECT IDENTIFIER    

juniAaaAssignBrasLicense 1.3.6.1.4.1.4874.2.2.20.1.1.1.1
The license string that determines the system-wide maximum number of remote user connections allowed. A zero-length string (no license) prohibits remote user connections.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..16)  

juniAaaAssignBrasLicensedUsers 1.3.6.1.4.1.4874.2.2.20.1.1.1.2
The system-wide maximum number of remote user connections allowed by the currently configured license string.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

juniAaaAssignDomainDelimiters 1.3.6.1.4.1.4874.2.2.20.1.1.1.3
The list of delimiters used to separate the user's name from the user's domain in the username field. The default is '@'.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..8)  

juniAaaAssignRealmDelimiters 1.3.6.1.4.1.4874.2.2.20.1.1.1.4
The list of delimiters used to separate the user's name from the user's realm in the username field. The realm is treated like the domain in the ERX. The default is none.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..8)  

juniAaaAssignDomainParseOrder 1.3.6.1.4.1.4874.2.2.20.1.1.1.5
The order in which the user's name is parsed: either search for domain first or realm first in the form (realm/user@domain.com). The default is domain first.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER domainFirst(1), realmFirst(2)  

juniAaaAssignSubscriberLimit 1.3.6.1.4.1.4874.2.2.20.1.1.1.6
The maximum number of subscribers permitted in this VR context. The value '0' means no limit.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..32000  

juniAaaAssignDomainMaxPadnPerDomain 1.3.6.1.4.1.4874.2.2.20.1.1.1.7
The maximum number of PPPoE active discovery network (PADN) entries permitted in a domain entry.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

juniAaaInterfaceIdFormat 1.3.6.1.4.1.4874.2.2.20.1.1.1.8
The interface ID format: include or exclude sub-interface per VR. The sub-interface is included or excluded at the time of the initial AAA request for the user and remains for the duration of the login.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER includeSubIntf(1), excludeSubIntf(2)  

juniAaaAssignTunnelCallingNumberFormat 1.3.6.1.4.1.4874.2.2.20.1.1.1.9
The format of the interface identifier passed to L2TP during an authentication request. L2TP uses this identifier as the calling-number (type 22) attribute value. Note: if selected components of the calling number format are not available (i.e. PPPoE Agent Circuit Id and Agent Remote Id), then the juniAaaAssignTunnelCallingNumberFallbackFormat will be used. Optionally the SVLAN ID inclusion can be enabled
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER descriptive(1), fixed(2), descriptiveIncludeAgentCircuitId(3), descriptiveIncludeAgentRemoteId(4), descriptiveIncludeAgentCircuitIdAndAgentRemoteId(5), agentCircuitId(6), agentRemoteId(7), agentCircuitIdIncludeAgentRemoteId(8), fixedIncludeSvlanId(9), fixedAdapterEmbedded(10), fixedAdapterNewField(11), fixedAdapterEmbeddedIncludeSvlanId(12), fixedAdapterNewFieldIncludeSvlanId(13)  

juniAaaAssignDomainParseDirection 1.3.6.1.4.1.4874.2.2.20.1.1.1.10
The direction in which the user's name is parsed: either search for domain delimiter from left to right or right to left; first delimiter marks boundry. The default is right to left.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER rightToLeft(1), leftToRight(2)  

juniAaaAssignRealmParseDirection 1.3.6.1.4.1.4874.2.2.20.1.1.1.11
The direction in which the user's name is parsed: either search for realm delimiter from left to right or right to left; first delimiter marks boundry. The default is left to right.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER rightToLeft(1), leftToRight(2)  

juniAaaInterfaceAdapterFormat 1.3.6.1.4.1.4874.2.2.20.1.1.1.12
The interface adapter format: include or exclude the adapter if present field per VR. The adapter field is included or excluded at the time of the initial AAA request for the user and remains for the duration of the login.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER includeAdapter(1), excludeAdapter(2)  

juniAaaAssignAccountingStatisticsType 1.3.6.1.4.1.4874.2.2.20.1.1.1.13
The method for collecting AAA acounting statistics. When value is 'full', collect a full set of statistics for AAA accounting. When the value is 'uptime', collect only uptime value for AAA accounting.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER full(0), uptime(1)  

juniAaaAssignQosDownstreamRate 1.3.6.1.4.1.4874.2.2.20.1.1.1.14
Enables/disables the reporting of the dsl downstream rate information to Qos.
Status: current Access: read-write
OBJECT-TYPE    
  JuniEnable  

juniAaaAssignTunnelCallingNumberFormatFallback 1.3.6.1.4.1.4874.2.2.20.1.1.1.15
The fallback format of the interface identifier passed to L2TP during an authentication request. L2TP uses this identifier as the calling-number (type 22) attribute value.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER descriptive(1), fixed(2), fixedIncludeSvlanId(3), fixedAdapterEmbedded(4), fixedAdapterNewField(5), fixedAdapterEmbeddedIncludeSvlanId(6), fixedAdapterNewFieldIncludeSvlanId(7)  

juniAaaFramedIpv6PrefixAsIpv6NdRaPrefix 1.3.6.1.4.1.4874.2.2.20.1.1.1.16
Enables/disables the use of framed-ipv6-prefix RADIUS attribute for IPv6 ND router advertisement.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

juniAaaDelegatedIpv6PrefixAsDhcpv6DelegatedPrefix 1.3.6.1.4.1.4874.2.2.20.1.1.1.17
Enables/disables the use of delegated-ipv6-prefix RADIUS attribute for DHCPv6 prefix delegation.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

juniAaaAssignDomain 1.3.6.1.4.1.4874.2.2.20.1.1.2
OBJECT IDENTIFIER    

juniAaaAssignDomainTable 1.3.6.1.4.1.4874.2.2.20.1.1.2.1
The entries in this table specify the assignment of a remote access user to a virtual router, based on the user's domain.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniAaaAssignDomainEntry

juniAaaAssignDomainEntry 1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1
A specification of the virtual router to which users on a specified domain should be assigned.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniAaaAssignDomainEntry  

juniAaaAssignDomainName 1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.1
The domain name uniquely identifying this entry.
Status: current Access: read-only
OBJECT-TYPE    
  JuniAaaDomainName  

juniAaaAssignDomainRowStatus 1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.2
Controls creation/deletion of entries in this table. Only the values 'createAndGo' and 'destroy' may be SET.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

juniAaaAssignDomainRouterName 1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.3
This variable is replaced by juniAaaAssignDomainAuthRouterName and juniAaaAssignDomainIpRouterName. It returns same value as juniAaaAssignDomainAuthRouterName.
Status: deprecated Access: read-only
OBJECT-TYPE    
  JuniName  

juniAaaAssignDomainLoopback 1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.4
The number of the loopback interface, associated with the specified virtual router, whose IP address is used as the source address when transmitting IP packets on unnumbered remote access user links. For example, if the associated loopback interface for this domain/router was configured via the console as 'loopback 2', this object would contain the integer value 2. A value of -1 indicates the loopback interface is unspecified.
Status: obsolete Access: read-create
OBJECT-TYPE    
  Integer32 -1..32000  

juniAaaAssignDomainIpHint 1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.5
Enables/disables the IP hint feature, which causes the system to allocate an IP address before going to RADIUS for authentication.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniAaaAssignDomainAtmServiceLevel 1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.6
The Service category for this circuit: ubr Unspecified bit rate (best effort). ubrPcr Unspecified Bit Rate with Peak Cell Rate limit. nrtVbr Non-realtime Variable Bit Rate. cbr Constant bit rate. rtVbr Realtime Variable Bit Rate. Set the service level in combination of the traffic attributes PCR/SCR/MBS in the following matrix for successfull configurations. ServiceLevel PCR SCR MBS ------------------------------------------ ubr omit omit omit ubrPcr must omit omit nrtVbr must must must cbr must omit omit rtVbr must must must
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER none(0), ubr(1), ubrPcr(2), nrtVbr(3), cbr(4), rtVbr(5)  

juniAaaAssignDomainAtmPcr 1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.7
Peak Cell Rate, in kilobits per second (kbps), of this circuit. This parameter is only required when juniAaaAssignDomainAtmServiceLevel is configured to have one of the following values: ubrPcr nrtVbr cbr
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..4294967294  

juniAaaAssignDomainAtmScr 1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.8
Sustained Cell Rate, in kilobits per second (kbps), of this circuit. This parameter is only required when juniAaaAssignDomainAtmServiceLevel is configured to have one of the following values: nrtVbr
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..4294967294  

juniAaaAssignDomainAtmMbs 1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.9
Maximum Burst Size, in cells, of this circuit. This parameter is only required when juniAaaAssugbDomainAtmServiceLevel is configured to have one of the following values: nrtVbr
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..4294967294  

juniAaaAssignDomainOverrideUserName 1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.10
The override user name associated with this entry. This object is used to override the user name of the remote client.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

juniAaaAssignDomainOverridePassword 1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.11
The override password for the user name defined by juniAaaAssignDomainOverrideUserName. This object is used to override the password part of the username/password pair of the remote client. This value returns a string length of 0 on reads for security reasons.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

juniAaaAssignDomainStripDomain 1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.12
Enables/disables the domain name stripping feature, which causes the system to strip the domain name before sending the access-request to RADIUS for authentication.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniAaaAssignDomainPoolName 1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.13
The name of the local address pool from which to allocate an IP address for the subscriber when none is returned from the authentication server.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..16)  

juniAaaAssignDomainLocalInterface 1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.14
The local interface, associated with the specified virtual router, whose IP address is used as the source address when transmitting IP packets on remote access user links.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..64)  

juniAaaAssignDomainIpv6RouterName 1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.15
The name of the virtual router to which remote access users within this domain are assigned for IPv6 interfaces.
Status: current Access: read-create
OBJECT-TYPE    
  JuniName  

juniAaaAssignDomainIpv6LocalInterface 1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.16
The local interface, associated with the specified virtual router, whose IPv6 address is used as the source address when transmitting IPv6 packets on remote access user links.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..64)  

juniAaaAssignDomainTunnelGroup 1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.17
The tunnel group assigned to this domain map. Non default configuration of this object cannot coexist with matching tunnel entries in juniAaaAssignDomainTunnelTable.
Status: current Access: read-create
OBJECT-TYPE    
  JuniAaaTunnelGroupName  

juniAaaAssignDomainAuthRouterName 1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.18
The name of the virtual router where remote access users within this domain will be authenticated.
Status: current Access: read-create
OBJECT-TYPE    
  JuniName  

juniAaaAssignDomainIpRouterName 1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.19
The name of the virtual router to which remote access users within this domain are assigned for IP interfaces.
Status: current Access: read-create
OBJECT-TYPE    
  JuniName  

juniAaaAssignDomainTunnelSubscriberAuthentication 1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.20
When there are tunnel configurations under this domain, enable or disable subscribers of this domain authenticate with configured authentication server.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

juniAaaAssignDomainBackupPoolName 1.3.6.1.4.1.4874.2.2.20.1.1.2.1.1.21
The name of the backup local address pool from which to allocate an IP address for the subscriber when the primary address pool is 100% allocated
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..16)  

juniAaaAssignDomainTunnelTable 1.3.6.1.4.1.4874.2.2.20.1.1.2.2
The entries in this table specify the tunnels associated with a domain.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniAaaAssignDomainTunnelEntry

juniAaaAssignDomainTunnelEntry 1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1
A specification of the tunnels associated with a domain.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniAaaAssignDomainTunnelEntry  

juniAaaAssignDomainTunnelName 1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.1
The domain name associated with this entry.
Status: current Access: read-only
OBJECT-TYPE    
  JuniAaaDomainName  

juniAaaAssignDomainTunnelTag 1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.2
The tunnel tag value associated with this entry.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..31  

juniAaaAssignDomainTunnelPreference 1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.3
The tunnel's preference value associated with this entry. The value 0 is the highest preference.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..2000  

juniAaaAssignDomainTunnelType 1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.4
The tunnel type associated with this entry. Attempts to set this object to tunnelUnknown(2) and tunnelL2f(3) will fail (wrongValue).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER tunnelL2tp(1), tunnelUnknown(2), tunnelL2f(3)  

juniAaaAssignDomainTunnelMedium 1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.5
The tunnel medium associated with this entry. The medium dictates the format of the tunnel address. Attempts to set this object to tunnelMediumUnknown(2) will fail (wrongValue).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER tunnelMediumIPv4(1), tunnelMediumUnknown(2)  

juniAaaAssignDomainTunnelAddress 1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.6
The tunnel server address associated with this entry. The juniAaaAssignDomainTunnelMedium object defines the format of the address. MEDIUM EXAMPLE FORMAT tunnelMedium_IPv4 xyz.xyz.xyz.xyz
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

juniAaaAssignDomainTunnelPassword 1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.7
The tunnel password associated with this entry. The object returns a null length string on reads due to security concerns.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

juniAaaAssignDomainTunnelId 1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.8
The tunnel identifier associated with this entry. The tunnel identifier is used to distinguish between multiple tunnels to the same juniAaaAssignDomainTunnelAddress.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

juniAaaAssignDomainTunnelHostName 1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.9
The tunnel client hostname associated with this entry. This object is analogous to the RADIUS attribute Tunnel-Client-Auth-ID. When a tunnel is established with a peer, this object can be used to distinguish groups of tunnels.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..64)  

juniAaaAssignDomainTunnelRowStatus 1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.10
Controls creation/deletion of entries in this table. Only the values 'createAndGo' and 'destroy' may be SET.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

juniAaaAssignDomainTunnelServerName 1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.11
The tunnel server hostname associated with this entry. This object is analogous to the RADIUS attribute Tunnel-Server-Auth-ID. When a tunnel is established with a peer, this object can be used to distinguish groups of tunnels.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..64)  

juniAaaAssignDomainTunnelClientAddress 1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.12
The tunnel client address associated with this entry. The juniAaaAssignDomainTunnelMedium object defines the format of the address. MEDIUM EXAMPLE FORMAT tunnelMedium_IPv4 xyz.xyz.xyz.xyz
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

juniAaaAssignDomainTunnelMaxSessions 1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.13
The tunnel's max-session value associated with this entry. The value 0 indicates no maximum session value.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

juniAaaAssignDomainTunnelReceiveWindowSize 1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.14
For an L2TP tunnel this object represents the receive window size. A value of 0 indicates that this object has no effect on the tunnel's receive window size.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0 | 4  

juniAaaAssignDomainTunnelFailoverResync 1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.15
For an L2TP tunnel this object represents the failover resync mechanism: disable(0) - Disable failover resync failoverProtocol(1) - Use the L2TP Failover Protocol silentFailover(2) - Use the JUNOSe Silent Failover Mechanism failoverProtocolFallbackToSilentFailover(3) - (Default) Use the L2TP Failover Protocol and fall back to Silent Failover.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disable(0), failoverProtocol(1), silentFailover(2), failoverProtocolFallbackToSilentFailover(3), notConfigured(4)  

juniAaaAssignDomainTunnelSwitchProfile 1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.16
The name of the L2TP tunnel switch profile to apply in tunnel switching scenarios.
Status: current Access: read-create
OBJECT-TYPE    
  JuniAaaTunnelSwitchProfileName  

juniAaaAssignDomainTunnelTxConnectSpeedMethod 1.3.6.1.4.1.4874.2.2.20.1.1.2.2.1.17
For an L2TP tunnel this object represents the tx connect speed method mechanism at the LAC: notSet(0) - this parameter has not been configured staticLayer2(1) - use static layer 2 settings dynamicLayer2(2) - use layer 2 settings including dynamic speeds qos(3) - use qos speed actual(4) - minimum of dynamicLayer2 and qos
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER notSet(0), staticLayer2(1), dynamicLayer2(2), qos(3), actual(4)  

juniAaaAssignDomainPadnTable 1.3.6.1.4.1.4874.2.2.20.1.1.2.3
The entries in this table specify the PPPoE active discovery network (PADN) parameters associated with a domain.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniAaaAssignDomainPadnEntry

juniAaaAssignDomainPadnEntry 1.3.6.1.4.1.4874.2.2.20.1.1.2.3.1
A specification of the PPPoE active discovery network parameters associated with a domain.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniAaaAssignDomainPadnEntry  

juniAaaAssignDomainPadnIpAddress 1.3.6.1.4.1.4874.2.2.20.1.1.2.3.1.1
The IP address of this entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

juniAaaAssignDomainPadnIpMask 1.3.6.1.4.1.4874.2.2.20.1.1.2.3.1.2
The IP mask of this entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

juniAaaAssignDomainPadnRowStatus 1.3.6.1.4.1.4874.2.2.20.1.1.2.3.1.3
Controls creation/deletion of entries in this table. Only the values 'createAndGo' and 'destroy' may be SET.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

juniAaaAssignDomainPadnDistance 1.3.6.1.4.1.4874.2.2.20.1.1.2.3.1.4
The administrative distance metric of this entry.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..255  

juniAaaTunnelGroups 1.3.6.1.4.1.4874.2.2.20.1.7.2
OBJECT IDENTIFIER    

juniAaaTunnelGroupTable 1.3.6.1.4.1.4874.2.2.20.1.7.2.1
The entries in this table specify tunnel attributes sufficient tunnel establishment.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniAaaTunnelGroupEntry

juniAaaTunnelGroupEntry 1.3.6.1.4.1.4874.2.2.20.1.7.2.1.1
An entry in the tunnel group table.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniAaaTunnelGroupEntry  

juniAaaTunnelGroupName 1.3.6.1.4.1.4874.2.2.20.1.7.2.1.1.1
The tunnel group name uniquely identifying this entry.
Status: current Access: read-only
OBJECT-TYPE    
  JuniAaaTunnelGroupName  

juniAaaTunnelGroupRowStatus 1.3.6.1.4.1.4874.2.2.20.1.7.2.1.1.2
Controls creation/deletion of entries in this table. Only the values 'createAndGo' and 'destroy' may be SET.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

juniAaaTunnelGroupTunnelTable 1.3.6.1.4.1.4874.2.2.20.1.7.2.2
The entries in this table specify the tunnels associated with a tunnel group.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniAaaTunnelGroupTunnelEntry

juniAaaTunnelGroupTunnelEntry 1.3.6.1.4.1.4874.2.2.20.1.7.2.2.1
A specification of the tunnels associated with a tunnel group.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniAaaTunnelGroupTunnelEntry  

juniAaaTunnelGroupTunnelName 1.3.6.1.4.1.4874.2.2.20.1.7.2.2.1.1
The tunnel group name associated with this entry.
Status: current Access: read-only
OBJECT-TYPE    
  JuniAaaTunnelGroupName  

juniAaaTunnelGroupTunnelTag 1.3.6.1.4.1.4874.2.2.20.1.7.2.2.1.2
The tunnel tag value associated with this entry.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..31  

juniAaaTunnelGroupTunnelPreference 1.3.6.1.4.1.4874.2.2.20.1.7.2.2.1.3
The tunnel's preference value associated with this entry. The value 0 is the highest preference.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..2000  

juniAaaTunnelGroupTunnelType 1.3.6.1.4.1.4874.2.2.20.1.7.2.2.1.4
The tunnel type associated with this entry.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER tunnelL2tp(1)  

juniAaaTunnelGroupTunnelMedium 1.3.6.1.4.1.4874.2.2.20.1.7.2.2.1.5
The tunnel medium associated with this entry. The medium dictates the format of the tunnel address. Attempts to set this object to tunnelMediumUnknown(2) will fail (wrongValue).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER tunnelMediumIPv4(1), tunnelMediumUnknown(2)  

juniAaaTunnelGroupTunnelAddress 1.3.6.1.4.1.4874.2.2.20.1.7.2.2.1.6
The tunnel server address associated with this entry. The juniAaaTunnelGroupTunnelMedium object defines the format of the address. MEDIUM EXAMPLE FORMAT tunnelMedium_IPv4 xyz.xyz.xyz.xyz
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

juniAaaTunnelGroupTunnelPassword 1.3.6.1.4.1.4874.2.2.20.1.7.2.2.1.7
The tunnel password associated with this entry. The object returns a null length string on reads due to security concerns.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

juniAaaTunnelGroupTunnelId 1.3.6.1.4.1.4874.2.2.20.1.7.2.2.1.8
The tunnel identifier associated with this entry. The tunnel identifier is used to distinguish between multiple tunnels to the same juniAaaTunnelGroupTunnelAddress.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

juniAaaTunnelGroupTunnelHostName 1.3.6.1.4.1.4874.2.2.20.1.7.2.2.1.9
The tunnel client hostname associated with this entry. This object is analogous to the RADIUS attribute Tunnel-Client-Auth-ID. When a tunnel is established with a peer, this object can be used to distinguish groups of tunnels.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..64)  

juniAaaTunnelGroupTunnelRowStatus 1.3.6.1.4.1.4874.2.2.20.1.7.2.2.1.10
Controls creation/deletion of entries in this table. Only the values 'createAndGo' and 'destroy' may be SET.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

juniAaaTunnelGroupTunnelServerName 1.3.6.1.4.1.4874.2.2.20.1.7.2.2.1.11
The tunnel server hostname associated with this entry. This object is analogous to the RADIUS attribute Tunnel-Server-Auth-ID. When a tunnel is established with a peer, this object can be used to distinguish groups of tunnels.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..64)  

juniAaaTunnelGroupTunnelClientAddress 1.3.6.1.4.1.4874.2.2.20.1.7.2.2.1.12
The tunnel client address associated with this entry. The juniAaaTunnelGroupTunnelMedium object defines the format of the address. MEDIUM EXAMPLE FORMAT tunnelMedium_IPv4 xyz.xyz.xyz.xyz
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

juniAaaTunnelGroupTunnelMaxSessions 1.3.6.1.4.1.4874.2.2.20.1.7.2.2.1.13
The tunnel's max-session value associated with this entry. The value 0 indicates no maximum session value.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

juniAaaTunnelGroupTunnelReceiveWindowSize 1.3.6.1.4.1.4874.2.2.20.1.7.2.2.1.14
For an L2TP tunnel this object represents the receive window size. A value of 0 indicates that this object has no effect on the tunnel's receive window size.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0 | 4  

juniAaaTunnelGroupTunnelRouterName 1.3.6.1.4.1.4874.2.2.20.1.7.2.2.1.15
The name of the virtual router to which remote access users within this tunnel are assigned.
Status: current Access: read-create
OBJECT-TYPE    
  JuniName  

juniAaaTunnelGroupTunnelFailoverResync 1.3.6.1.4.1.4874.2.2.20.1.7.2.2.1.16
For an L2TP tunnel this object represents the failover resync mechanism: disable(0) - Disable failover resync failoverProtocol(1) - Use the L2TP Failover Protocol silentFailover(2) - Use the JUNOSe Silent Failover Mechanism failoverProtocolFallbackToSilentFailover(3) - (Default) Use the L2TP Failover Protocol and fall back to Silent Failover.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disable(0), failoverProtocol(1), silentFailover(2), failoverProtocolFallbackToSilentFailover(3), notConfigured(4)  

juniAaaTunnelGroupTunnelSwitchProfile 1.3.6.1.4.1.4874.2.2.20.1.7.2.2.1.17
The name of the L2TP tunnel switch profile to apply in tunnel switching scenarios.
Status: current Access: read-create
OBJECT-TYPE    
  JuniAaaTunnelSwitchProfileName  

juniAaaTunnelGroupTunnelTxConnectSpeedMethod 1.3.6.1.4.1.4874.2.2.20.1.7.2.2.1.18
For an L2TP tunnel this object represents the tx connect speed method mechanism at the LAC: notSet(0) - this parameter has not been configured staticLayer2(1) - use static layer 2 settings dynamicLayer2(2) - use layer 2 settings including dynamic speeds qos(3) - use qos speed actual(4) - minimum of dynamicLayer2 and qos
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER notSet(0), staticLayer2(1), dynamicLayer2(2), qos(3), actual(4)  

juniAaaAuthGeneral 1.3.6.1.4.1.4874.2.2.20.1.2.1
OBJECT IDENTIFIER    

juniAaaLocalAuth 1.3.6.1.4.1.4874.2.2.20.1.2.2
OBJECT IDENTIFIER    

juniAaaLocalAuthUser 1.3.6.1.4.1.4874.2.2.20.1.2.2.1
OBJECT IDENTIFIER    

juniAaaLocalAuthUserDb 1.3.6.1.4.1.4874.2.2.20.1.2.2.2
OBJECT IDENTIFIER    

juniAaaLocalAuthUserDbAssoc 1.3.6.1.4.1.4874.2.2.20.1.2.2.3
OBJECT IDENTIFIER    

juniAaaAuthMethods 1.3.6.1.4.1.4874.2.2.20.1.2.1.1
The set of authentication protocols configured on this system. Each octet in this object contains one of the values defined in the JuniAaaAuthenticationMethods TEXTUAL-CONVENTION. The system will sequence through each octet of this object starting at octet 1 and attempt to use the corresponding authentication protocol defined by JuniAaaAuthenticationMethods. Note that if the octet is set to: protocolNone(4) Then authentication does not take place. If an authentication protocol is configured and attempts to reach the authentication server fail, the system will move to the next octet in this object and retry the authentication in the form dictated by the corresponding authentication protocoltype. The process of sequencing thru each octet will stop if the authentication server is successfully contacted, or there are no more configured octets in this object.
Status: obsolete Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..5)  

juniAaaAuthMethodsTable 1.3.6.1.4.1.4874.2.2.20.1.2.1.2
The entries in this table specify the assignment of authentication methods for a particular subscriber type.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniAaaAuthMethodsEntry

juniAaaAuthMethodsEntry 1.3.6.1.4.1.4874.2.2.20.1.2.1.2.1
A specification of the authentication methods for a particular subscriber type.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniAaaAuthMethodsEntry  

juniAaaAuthMethodsSubscriberType 1.3.6.1.4.1.4874.2.2.20.1.2.1.2.1.1
The subscriber type.
Status: current Access: read-only
OBJECT-TYPE    
  JuniAaaAuthenticationSubscriberTypes  

juniAaaAuthMethodsAuthentication 1.3.6.1.4.1.4874.2.2.20.1.2.1.2.1.2
The set of authentication protocols configured on this system. Each octet in this object contains one of the values defined in the JuniAaaAuthenticationMethods TEXTUAL-CONVENTION. The system will sequence through each octet of this object starting at octet 1 and attempt to use the corresponding authentication protocol defined by JuniAaaAuthenticationMethods. Note that if the octet is set to: protocolNone(4) Then authentication does not take place. If an authentication protocol is configured and attempts to reach the authentication server fail, the system will move to the next octet in this object and retry the authentication in the form dictated by the corresponding authentication protocoltype. The process of sequencing thru each octet will stop if the authentication server is successfully contacted, or there are no more configured octets in this object.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..5)  

juniAaaLocalAuthUserTable 1.3.6.1.4.1.4874.2.2.20.1.2.2.1.1
This table contains entries for users present in the local user databases.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniAaaLocalAuthUserEntry

juniAaaLocalAuthUserEntry 1.3.6.1.4.1.4874.2.2.20.1.2.2.1.1.1
Each entry in this table represents a single user in a local user database.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniAaaLocalAuthUserEntry  

juniAaaLocalAuthUserName 1.3.6.1.4.1.4874.2.2.20.1.2.2.1.1.1.1
The name of the user.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(1..64)  

juniAaaLocalAuthUserRowStatus 1.3.6.1.4.1.4874.2.2.20.1.2.2.1.1.1.2
Controls creation/deletion of entries in this table. Only 'createAndGo' and 'destroy' enumeration values are supported.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

juniAaaLocalAuthUserPassword 1.3.6.1.4.1.4874.2.2.20.1.2.2.1.1.1.3
The password for this user. If the juniAaaLocalAuthUserEncrypted object is not set with this object, the password value is assumed to be unencrypted. When set, any existing password is overwritten. Setting a zero length OCTET STRING removes the password. Reading this object always results in a zero length OCTET STRING.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

juniAaaLocalAuthUserEncryption 1.3.6.1.4.1.4874.2.2.20.1.2.2.1.1.1.4
The encryption type of the password value being set with the juniAaaLocalAuthUserPassword object. Reading this object always results in a value of encryptionNone. encyptionNone - The password is unencrypted (i.e. in plain text.) encyptionSecret - The password has been generated using a one-way MD5 encryption mechanism, algorithm 5. encyptionPassword - The password has been generated using a two-way encryption mechanism, algorithm 8.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER encryptionNone(0), encryptionSecret(5), encryptionPassword(8)  

juniAaaLocalAuthUserIpAddress 1.3.6.1.4.1.4874.2.2.20.1.2.2.1.1.1.5
The IP address this user is to be assigned, once authenticated. This object corresponds to the Framed-IP-Address attribute in RADIUS authentication servers.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

juniAaaLocalAuthUserIpAddressPool 1.3.6.1.4.1.4874.2.2.20.1.2.2.1.1.1.6
The name of the local address pool this user is to be allocated an IP address from, once authenticated. This object corresponds to the Framed-Pool attribute in RADIUS authentication servers.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..16)  

juniAaaLocalAuthUserRouterName 1.3.6.1.4.1.4874.2.2.20.1.2.2.1.1.1.7
The name of the router this user is to be assigned to, once authenticated. This object corresponds to the Unispher-Virtual-Router attribute in RADIUS authentication servers.
Status: current Access: read-create
OBJECT-TYPE    
  JuniName  

juniAaaLocalAuthUserDbTable 1.3.6.1.4.1.4874.2.2.20.1.2.2.2.1
This table contains entries for local user databases.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniAaaLocalAuthUserDbEntry

juniAaaLocalAuthUserDbEntry 1.3.6.1.4.1.4874.2.2.20.1.2.2.2.1.1
Each entry in this table represents a single local user database.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniAaaLocalAuthUserDbEntry  

juniAaaLocalAuthUserDbName 1.3.6.1.4.1.4874.2.2.20.1.2.2.2.1.1.1
The name of this local user database.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(1..32)  

juniAaaLocalAuthUserDbRowStatus 1.3.6.1.4.1.4874.2.2.20.1.2.2.2.1.1.2
Controls creation/deletion of entries in this table. Only 'createAndGo' and 'destroy' enumeration values are supported.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

juniAaaLocalAuthUserDbAssocTable 1.3.6.1.4.1.4874.2.2.20.1.2.2.3.1
This table contains entries that identify the local user database that is associated with each virtual router.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniAaaLocalAuthUserDbAssocEntry

juniAaaLocalAuthUserDbAssocEntry 1.3.6.1.4.1.4874.2.2.20.1.2.2.3.1.1
Each entry in this table represents a single association between a virtual router and local user database. The same database can be referenced by multiple virtual routers; however, a virtual router can reference only one database. No entries are displayed for virtual routers that reference the default local user database.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniAaaLocalAuthUserDbAssocEntry  

juniAaaLocalAuthUserDbAssocRowStatus 1.3.6.1.4.1.4874.2.2.20.1.2.2.3.1.1.1
Controls creation/deletion of entries in this table. Only 'createAndGo' and 'destroy' enumeration values are supported. When a virtual router is deleted, its corresponding entries in this table will be deleted as well.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

juniAaaLocalAuthUserDbAssocDbName 1.3.6.1.4.1.4874.2.2.20.1.2.2.3.1.1.2
The name of local user database associated with this virtual router. Setting the name to the default local user database, 'default', will delete this entry, as this is the default association for all virtual routers.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..32)  

juniAaaAcctGeneral 1.3.6.1.4.1.4874.2.2.20.1.3.1
OBJECT IDENTIFIER    

juniAaaAcctInterval 1.3.6.1.4.1.4874.2.2.20.1.3.1.1
The interval that must elapse between generation of accounting reports, ranging from 10 minutes to 24 hours, or disabled if set to zero. The set of this object affects both the juniAaaServiceAcctInterval and juniAaaUserAcctInterval values; the get of this object returns only the juniAaaUserAcctInterval value.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0 | 600..86400  

juniAaaAcctDupServerRouterName 1.3.6.1.4.1.4874.2.2.20.1.3.1.2
The name of another router on this system to which accounting reports should be sent, in addition to or instead of sending accounting reports to the accounting service (if any) configured on the current router (i.e., the router context within which this object instance exists). A zero-length name disables this mechanism.
Status: current Access: read-write
OBJECT-TYPE    
  JuniName  

juniAaaAcctMethods 1.3.6.1.4.1.4874.2.2.20.1.3.1.3
The set of accounting protocols configured on this system. Each octet in this object contains one of the values defined in the JuniAaaAccountingMethods TEXTUAL CONVENTION. The system will sequence through each octet of this object starting at octet 1 and attempt to use the corresponding accounting protocol defined by JuniAaaAccountingMethods. Note that if the octet is set to: protocolNone(4) Then accounting is disabled. If an accounting protocol is configured and reports are not successfully generated, the system will move to the next octet in this object and repeat the attempt to generate an accounting report in the form dictated by the corresponding accounting protocol type. The process of sequencing thru each octet will stop if accounting reports are either successfully generated, or there are no more configured octets in this object.
Status: obsolete Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..5)  

juniAaaAcctSendStopOnAaaDeny 1.3.6.1.4.1.4874.2.2.20.1.3.1.4
Enables/disables the accounting stop message sent to the accounting server when authentication server grants access, but AAA denies access.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

juniAaaAcctSendStopOnAaaReject 1.3.6.1.4.1.4874.2.2.20.1.3.1.5
Enables/disables the accounting stop message sent to the accounting server when authentication server denies access.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

juniAaaAcctSendImmediateAcctUpdate 1.3.6.1.4.1.4874.2.2.20.1.3.1.6
Enables/disables the sending of an accounting update with the client's IP address upon receipt of accounting start response.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

juniAaaAcctMethodsTable 1.3.6.1.4.1.4874.2.2.20.1.3.1.7
The entries in this table specify the assignment of accounting methods for a particular subscriber type.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniAaaAcctMethodsEntry

juniAaaAcctMethodsEntry 1.3.6.1.4.1.4874.2.2.20.1.3.1.7.1
A specification of the accounting methods for a particular subscriber type.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniAaaAcctMethodsEntry  

juniAaaAcctMethodsSubscriberType 1.3.6.1.4.1.4874.2.2.20.1.3.1.7.1.1
The subscriber type.
Status: current Access: read-only
OBJECT-TYPE    
  JuniAaaAccountingSubscriberTypes  

juniAaaAcctMethodsAccounting 1.3.6.1.4.1.4874.2.2.20.1.3.1.7.1.2
The set of accounting protocols configured on this system. Each octet in this object contains one of the values defined in the JuniAaaAccountingMethods TEXTUAL CONVENTION. The system will sequence through each octet of this object starting at octet 1 and attempt to use the corresponding accounting protocol defined by JuniAaaAccountingMethods. Note that if the octet is set to: protocolNone(4) Then accounting is disabled. If an accounting protocol is configured and reports are not successfully generated, the system will move to the next octet in this object and repeat the attempt to generate an accounting report in the form dictated by the corresponding accounting protocol type. The process of sequencing thru each octet will stop if accounting reports are either successfully generated, or there are no more configured octets in this object.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..5)  

juniAaaAcctBcastServerGroupName 1.3.6.1.4.1.4874.2.2.20.1.3.1.8
The name of a group of other routers on this system to which accounting reports should be sent, for every subsriber who has this router assigned as an operational router. A zero-length name disables this mechanism.
Status: current Access: read-write
OBJECT-TYPE    
  JuniVrfGroupName  

juniAaaUserAcctInterval 1.3.6.1.4.1.4874.2.2.20.1.3.1.9
The interval that must elapse between generation of user accounting reports, ranging from 10 minutes to 24 hours, or disabled if set to zero.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0 | 600..86400  

juniAaaServiceAcctInterval 1.3.6.1.4.1.4874.2.2.20.1.3.1.10
The interval that must elapse between generation of service accounting reports, ranging from 10 minutes to 24 hours, or disabled if set to zero.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0 | 600..86400  

juniAaaAcctBcastConfig 1.3.6.1.4.1.4874.2.2.20.1.3.2
OBJECT IDENTIFIER    

juniAaaAcctBcastServerGroupTable 1.3.6.1.4.1.4874.2.2.20.1.3.2.1
The entries in this table specify broadcast accounting routers of the named group. In addition to row status operations if juniAaaAcctBrasServerGroupRouter1, juniAaaAcctBrasServerGroupRouter2, juniAaaAcctBrasServerGroupRouter3 and juniAaaAcctBrasServerGroupRouter4 are all set zero length strings, the entry will be deleted. At least one non zero length string router is required to successfully create and entry. All non zero length string routers have to be unique within the group.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniAaaAcctBcastServerGroupEntry

juniAaaAcctBcastServerGroupEntry 1.3.6.1.4.1.4874.2.2.20.1.3.2.1.1
A specification of the accounting servers for a particular group.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniAaaAcctBcastServerGroupEntry  

juniAaaAcctBcastServerGroup 1.3.6.1.4.1.4874.2.2.20.1.3.2.1.1.1
The group name.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniVrfGroupName  

juniAaaAcctBcastServerGroupRouter1 1.3.6.1.4.1.4874.2.2.20.1.3.2.1.1.2
The name of the first router in the group.
Status: current Access: read-write
OBJECT-TYPE    
  JuniName  

juniAaaAcctBcastServerGroupRouter2 1.3.6.1.4.1.4874.2.2.20.1.3.2.1.1.3
The name of the second router in the group.
Status: current Access: read-write
OBJECT-TYPE    
  JuniName  

juniAaaAcctBcastServerGroupRouter3 1.3.6.1.4.1.4874.2.2.20.1.3.2.1.1.4
The name of the third router in the group.
Status: current Access: read-write
OBJECT-TYPE    
  JuniName  

juniAaaAcctBcastServerGroupRouter4 1.3.6.1.4.1.4874.2.2.20.1.3.2.1.1.5
The name of the third router in the group.
Status: current Access: read-write
OBJECT-TYPE    
  JuniName  

juniAaaAcctBcastServerGroupRowStatus 1.3.6.1.4.1.4874.2.2.20.1.3.2.1.1.6
Controls creation/deletion of entries in this table. Only the values 'createAndGo' and 'destroy' may be SET. In addition to row status operations if juniAaaAcctBrasServerGroupRouter1, juniAaaAcctBrasServerGroupRouter2, juniAaaAcctBrasServerGroupRouter3 and juniAaaAcctBrasServerGroupRouter4 are all set zero length strings, the entry will be deleted. At least one non zero length string router is required to successfully create and entry.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

juniAaaAddrGeneral 1.3.6.1.4.1.4874.2.2.20.1.4.1
OBJECT IDENTIFIER    

juniAaaAddrPoolDefault 1.3.6.1.4.1.4874.2.2.20.1.4.1.1
Identifies the default source of IP address allocation for remote access links: none No address source is specified. Using this setting allows the remote PPP subscriber (client) to set it's own address. local Use the local address pool named 'default'. dhcp Use DHCP service.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), local(1), dhcp(2)  

juniAaaDupAddrCheck 1.3.6.1.4.1.4874.2.2.20.1.4.1.2
Enables/disables the duplicate IP address checking which causes the system to check the route table for the PPP user's dynamic IP address is provided to PPP (from AAA).
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

juniAaaAddrNameServer 1.3.6.1.4.1.4874.2.2.20.1.4.2
OBJECT IDENTIFIER    

juniAaaAddrDns 1.3.6.1.4.1.4874.2.2.20.1.4.2.1
OBJECT IDENTIFIER    

juniAaaAddrWins 1.3.6.1.4.1.4874.2.2.20.1.4.2.2
OBJECT IDENTIFIER    

juniAaaAddrDnsPrimary 1.3.6.1.4.1.4874.2.2.20.1.4.2.1.1
The IP address of the primary DNS server to be used by remote access clients. A value of 0.0.0.0 indicates no server is configured.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

juniAaaAddrDnsSecondary 1.3.6.1.4.1.4874.2.2.20.1.4.2.1.2
The IP address of the secondary DNS server to be used by remote access clients. A value of 0.0.0.0 indicates no server is configured.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

juniAaaAddrIpv6DnsPrimary 1.3.6.1.4.1.4874.2.2.20.1.4.2.1.3
The IPv6 address of the primary IPv6 DNS server to be used by remote access clients. A value of ::0 indicates no server is configured.
Status: current Access: read-write
OBJECT-TYPE    
  Ipv6Address  

juniAaaAddrIpv6DnsSecondary 1.3.6.1.4.1.4874.2.2.20.1.4.2.1.4
The IPv6 address of the secondary IPv6 DNS server to be used by remote access clients. A value of ::0 indicates no server is configured.
Status: current Access: read-write
OBJECT-TYPE    
  Ipv6Address  

juniAaaAddrWinsPrimary 1.3.6.1.4.1.4874.2.2.20.1.4.2.2.1
The IP address of the primary WINS server to be used by remote access clients. A value of 0.0.0.0 indicates no server is configured.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

juniAaaAddrWinsSecondary 1.3.6.1.4.1.4874.2.2.20.1.4.2.2.2
The IP address of the secondary WINS server to be used by remote access clients. A value of 0.0.0.0 indicates no server is configured.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

juniAaaTimeoutGeneral 1.3.6.1.4.1.4874.2.2.20.1.6.1
OBJECT IDENTIFIER    

juniAaaIdleTimeout 1.3.6.1.4.1.4874.2.2.20.1.6.1.1
The maximum number of seconds that a user session can be idle before system disconnects the user, ranging from 300 to 86400 seconds, 0 disables idle timeout.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0 | 300..86400  

juniAaaSessionTimeout 1.3.6.1.4.1.4874.2.2.20.1.6.1.2
The maximum number of seconds that a user session can be established before system disconnects the user, ranging from 60 to 31622400 seconds. 0 specifies that a default value should be used, according to the rules of the implementing interface.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0 | 60..31622400  

juniAaaMonitorIngressTrafficOnly 1.3.6.1.4.1.4874.2.2.20.1.6.1.3
Enables/disables the monitoring of ingress traffic. Inactive sessions are disconnected after a period, specified in juniAaaIdleTimeout. Inactivity is determined by both inbound and outbound traffic. If this option is enabled, only ingress traffic is monitored for determining session inactivity.
Status: current Access: read-write
OBJECT-TYPE    
  JuniEnable  

juniAaaTunnelGeneral 1.3.6.1.4.1.4874.2.2.20.1.7.1
OBJECT IDENTIFIER    

juniAaaTunnelClientName 1.3.6.1.4.1.4874.2.2.20.1.7.1.1
The default tunnel client hostname associated with this virtual router. This object is used when no tunnel client name (client auth ID) is supplied in the authentication response.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

juniAaaTunnelPassword 1.3.6.1.4.1.4874.2.2.20.1.7.1.2
The default tunnel password associated with this virtual router. This object is used when no tunnel password is supplied in the authentication response. The object returns a null length string on reads due to security concerns.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

juniAaaTunnelNasPortMethod 1.3.6.1.4.1.4874.2.2.20.1.7.1.3
The default tunnel NAS-port method associated with this virtual router. This object is used to specify the LAC's NAS-port method. This provides limit compatiability to Cisco LNS for the NAS-port method AVP.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), ciscoAvp(1)  

juniAaaTunnelIgnoreNasPort 1.3.6.1.4.1.4874.2.2.20.1.7.1.4
Enables/disables the use of the NAS-port value that is passed in from the tunnel application.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

juniAaaTunnelIgnoreNasPortType 1.3.6.1.4.1.4874.2.2.20.1.7.1.5
Enables/disables the use of the NAS-port-type value that is passed in from the tunnel application.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

juniAaaTunnelAssignmentIdFormat 1.3.6.1.4.1.4874.2.2.20.1.7.1.6
The tunnel assignment ID format for distinguishing tunnel definitions. This object is used to specify the tunnel assigment ID format passed to the LAC. The value assignmentId(0) indicates that the original tunnel assignment ID value is to be used; clientServerId(1) indicates that the concatenated value from client-auth-name, server-auth-name, and assignment-id is to be used.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER assignmentId(0), clientServerId(1)  

juniAaaTunnelSwitchProfile 1.3.6.1.4.1.4874.2.2.20.1.7.1.7
The default tunnel switch profile associated with this virtual router. This object is used when no tunnel switch profile is supplied in the authentication response.
Status: current Access: read-write
OBJECT-TYPE    
  JuniAaaTunnelSwitchProfileName  

juniAaaTunnelTxConnectSpeedMethod 1.3.6.1.4.1.4874.2.2.20.1.7.1.8
The default tunnel tx connect speed method associated with this virtual router. This object is used to specify the LAC's tx connect speed method.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notSet(0), staticLayer2(1), dynamicLayer2(2), qos(3), actual(4)  

juniAaaIncomingInitiateRequests 1.3.6.1.4.1.4874.2.2.20.1.5.1
The number of AAA incoming initiate requests
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

juniAaaIncomingTerminateRequests 1.3.6.1.4.1.4874.2.2.20.1.5.2
The number of AAA incomining termination requests
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

juniAaaOutgoingTunnelGrantResponses 1.3.6.1.4.1.4874.2.2.20.1.5.3
The number of AAA outgoing tunnel grant responses
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

juniAaaOutgoingGrantResponses 1.3.6.1.4.1.4874.2.2.20.1.5.4
The number of AAA outgoing grant responses
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

juniAaaOutgoingDenyResponses 1.3.6.1.4.1.4874.2.2.20.1.5.5
The number of AAA outgoing deny responses
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

juniAaaOutgoingErrorResponses 1.3.6.1.4.1.4874.2.2.20.1.5.6
The number of AAA outgoing error responses
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

juniAaaOutgoingAuthRequests 1.3.6.1.4.1.4874.2.2.20.1.5.7
The number of AAA outgoing authentication requests
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

juniAaaIncomingAuthResponses 1.3.6.1.4.1.4874.2.2.20.1.5.8
The number of AAA incoming authentication responses
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

juniAaaOutgoingReAuthRequests 1.3.6.1.4.1.4874.2.2.20.1.5.9
The number of AAA outgoing re-authentication requests
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

juniAaaIncomingReAuthResponses 1.3.6.1.4.1.4874.2.2.20.1.5.10
The number of AAA incoming re-authentication responses
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

juniAaaOutgoingAcctRequests 1.3.6.1.4.1.4874.2.2.20.1.5.11
The number of AAA outgoing accounting requests
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

juniAaaIncomingAcctResponses 1.3.6.1.4.1.4874.2.2.20.1.5.12
The number of AAA incoming accounting responses
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

juniAaaOutgoingDupAcctRequests 1.3.6.1.4.1.4874.2.2.20.1.5.13
The number of AAA outgoing duplicate accounting requests
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

juniAaaIncomingDupAcctResponses 1.3.6.1.4.1.4874.2.2.20.1.5.14
The number of AAA incoing duplication accounting responses
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

juniAaaOutgoingAddrRequests 1.3.6.1.4.1.4874.2.2.20.1.5.15
The number of AAA outgoing address requests
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

juniAaaIncomingAddrResponses 1.3.6.1.4.1.4874.2.2.20.1.5.16
The number of AAA incoming address responses
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

juniAaaOutgoingBcastAcctRequests 1.3.6.1.4.1.4874.2.2.20.1.5.17
The number of AAA outgoing broadcast accounting requests
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

juniAaaIncomingBcastAcctResponses 1.3.6.1.4.1.4874.2.2.20.1.5.18
The number of AAA incoing broadcast accounting responses
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

juniAaaSubscriberMaxCount 1.3.6.1.4.1.4874.2.2.20.1.8.1
The configuration setting for the maximum number of subscribers. There is a grace number of subscribers above this limit, which when reached will cause authentication requests to be denied.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

juniAaaSubscriberPeakCount 1.3.6.1.4.1.4874.2.2.20.1.8.2
The peak number of subscribers. The peak count includes successfully authenticated subscribers as well as those subscribers in the process of being authenticated.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

juniAaaSubscriberCount 1.3.6.1.4.1.4874.2.2.20.1.8.3
The current number of subscribers. The subscriber count includes successfully authenticated subscribers as well as those subscribers in the process of being authenticated.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

juniAaaSubscriberTable 1.3.6.1.4.1.4874.2.2.20.1.8.4
The entries in this table represent subscribers by subscriber handle value.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniAaaSubscriberEntry

juniAaaSubscriberEntry 1.3.6.1.4.1.4874.2.2.20.1.8.4.1
A specification of subscribers by subscriber handle.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniAaaSubscriberEntry  

juniAaaSubscriberHandle 1.3.6.1.4.1.4874.2.2.20.1.8.4.1.1
The subscriber handle associated with this subscriber. A subscriber handle is a monotomically increasing integer.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

juniAaaSubscriberUserName 1.3.6.1.4.1.4874.2.2.20.1.8.4.1.2
The RADIUS userName associated with this subscriber.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

juniAaaSubscriberRouterName 1.3.6.1.4.1.4874.2.2.20.1.8.4.1.3
The virtual router assigned to this subscriber.
Status: current Access: read-only
OBJECT-TYPE    
  JuniName  

juniAaaSubscriberRouterIndex 1.3.6.1.4.1.4874.2.2.20.1.8.4.1.4
The router index that identifies the virtual router associated with this subscriber. The value of this object can be used to index the router in the juniRouterTable.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

juniAaaSubscriberLoginTime 1.3.6.1.4.1.4874.2.2.20.1.8.4.1.5
The time this subscriber logged in to RADIUS server.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

juniAaaSubscriberIpAddress 1.3.6.1.4.1.4874.2.2.20.1.8.4.1.6
The client IP Address assigned to this subscriber.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

juniAaaSubscriberIpAddressMask 1.3.6.1.4.1.4874.2.2.20.1.8.4.1.7
The client IP Address Mask assigned to this subscriber.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

juniAaaSubscriberAddrAssignType 1.3.6.1.4.1.4874.2.2.20.1.8.4.1.8
The address assignment type for this subscriber.
Status: current Access: read-only
OBJECT-TYPE    
  JuniAddressAssignType  

juniAaaSubscriberInterfaceId 1.3.6.1.4.1.4874.2.2.20.1.8.4.1.9
A text string describing the local interface associated with this subscriber. Types/formats/examples for this string include: ERX: == /; E320: == //; ATM Virtual Circuit atm :. 'atm 3/2:0.100' (ERX) 'atm 3/0/2:0.100' (E320) Ethernet { fastEthernet | gigabitEthernet } 'fastEthernet 3/2' (ERX) 'gigabitEthernet 3/2' (ERX) 'gigabitEthernet 3/0/2' (E320) 'tenGigabitEthernet 3/0/2' (E320) Ethernet VLAN { fastEthernet | gigabitEthernet } : 'fastEthernet 3/2:1000' (ERX) 'gigabitEthernet 3/2:1000' (ERX) 'gigabitEthernet 3/0/2:1000' (E320) 'tenGigabitEthernet 3/0/2:1000' (E320) Channelized Serial serial :[/]* 'serial 3/2:4' (ERX T1/E1) 'serial 3/2:2/4' (ERX T3/E3) 'serial 3/2:2/1/1/4' (ERX OC3/OC12 - channelized DS3) 'serial 3/2:2/1/1/1/4' (ERX OC3/OC12 - virtual tributaries) 'serial 3/0/2:2/1/1/4' (E320 OC3/OC12 - channelized DS3) 'serial 3/0/2:2/1/1/1/4' (E320 OC3/OC12 - virtual tributaries) L2TP over IP ip::::: :: 'ip:10.10.0.1:20.20.0.2:1234:5678:9abc:def0:6789abcd' (Note: tunnelIDs, sessionIDs, and callSerialNumber are in hexadecimal.) Other formats may be supported over time.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

juniAaaSubscriberState 1.3.6.1.4.1.4874.2.2.20.1.8.4.1.10
The state of this subscriber.
Status: current Access: read-only
OBJECT-TYPE    
  JuniSubscriberState  

juniAaaSubscriberClientType 1.3.6.1.4.1.4874.2.2.20.1.8.4.1.11
The client type for this subscriber. Certain client types (e.g., 'other') might be suppressed from representation in this table.
Status: current Access: read-only
OBJECT-TYPE    
  JuniSubscriberClientType  

juniAaaSubscriberIngressPolicyName 1.3.6.1.4.1.4874.2.2.20.1.8.4.1.12
The Ingress Policy Name associated with this subscriber.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

juniAaaSubscriberEgressPolicyName 1.3.6.1.4.1.4874.2.2.20.1.8.4.1.13
The Egress Policy Name associated with this subscriber.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

juniAaaSubscriberQosProfileName 1.3.6.1.4.1.4874.2.2.20.1.8.4.1.14
The QoS Profile Name associated with this subscriber.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

juniAaaSubscriberRowStatus 1.3.6.1.4.1.4874.2.2.20.1.8.4.1.15
Controls the deletion of the subscriber from this table. Deletion of the subscriber is analogous to logging the subscriber out of the network. Note: only 'destroy' is supported for SNMP SET operations.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

juniAaaSubscriberIpv6RouterIndex 1.3.6.1.4.1.4874.2.2.20.1.8.4.1.16
The router index that identifies the virtual router associated with this subscriber's IPv6 interface. The value of this object can be used to index the router in the juniRouterTable.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

juniAaaSubscriberIpv6AddrIfIdentifier 1.3.6.1.4.1.4874.2.2.20.1.8.4.1.17
The client IPv6 Address Interface Identifier assigned to this subscriber.
Status: current Access: read-only
OBJECT-TYPE    
  Ipv6AddressIfIdentifier  

juniAaaSubscriberRouterSummaryTable 1.3.6.1.4.1.4874.2.2.20.1.8.5
The entries in this table report number of subscribers per router.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniAaaSubscriberRouterSummaryEntry

juniAaaSubscriberRouterSummaryEntry 1.3.6.1.4.1.4874.2.2.20.1.8.5.1
A specification of subscribers for a router.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniAaaSubscriberRouterSummaryEntry  

juniAaaSubscriberRouterSummaryRouterIndex 1.3.6.1.4.1.4874.2.2.20.1.8.5.1.1
The router index of the virtual router. The value of this object can be used to retrieve additional information in the router mib.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

juniAaaSubscriberRouterSummaryCount 1.3.6.1.4.1.4874.2.2.20.1.8.5.1.2
The number of subscribers on this router.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

juniAaaSubscriberRouterTable 1.3.6.1.4.1.4874.2.2.20.1.8.6
The entries in this table sort subscribers by router ID.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniAaaSubscriberRouterEntry

juniAaaSubscriberRouterEntry 1.3.6.1.4.1.4874.2.2.20.1.8.6.1
A specification of subscribers by router ID.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniAaaSubscriberRouterEntry  

juniAaaSubscriberRouterRouterIndex 1.3.6.1.4.1.4874.2.2.20.1.8.6.1.1
The router index of the virtual router. The value of this object can be used to retrieve additional information in the router MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

juniAaaSubscriberRouterHandle 1.3.6.1.4.1.4874.2.2.20.1.8.6.1.2
The subscriber handle associated with this subscriber. A subscriber handle is a monotonically increasing integer.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

juniAaaSubscriberRouterRowStatus 1.3.6.1.4.1.4874.2.2.20.1.8.6.1.3
Always has value 'active'.
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

juniAaaSubscriberLocationType 1.3.6.1.4.1.4874.2.2.20.1.8.7
Describes the interpretation of JuniInterfaceLocationValue object values into platform-dependent interface location components, e.g., 'slot.port' on an ERX.
Status: current Access: read-only
OBJECT-TYPE    
  JuniInterfaceLocationType  

juniAaaSubscriberLocationSummaryTable 1.3.6.1.4.1.4874.2.2.20.1.8.8
The entries in this table report number of subscribers per interface location.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniAaaSubscriberLocationSummaryEntry

juniAaaSubscriberLocationSummaryEntry 1.3.6.1.4.1.4874.2.2.20.1.8.8.1
A specification of subscribers on an interface location.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniAaaSubscriberLocationSummaryEntry  

juniAaaSubscriberLocationSummaryLocationIndex 1.3.6.1.4.1.4874.2.2.20.1.8.8.1.1
The value of a platform interface location.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniInterfaceLocationValue  

juniAaaSubscriberLocationSummaryCount 1.3.6.1.4.1.4874.2.2.20.1.8.8.1.2
The number of subscribers associated with this interface location.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

juniAaaSubscriberLocationTable 1.3.6.1.4.1.4874.2.2.20.1.8.9
The entries in this table sort subscribers by interface location.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniAaaSubscriberLocationEntry

juniAaaSubscriberLocationEntry 1.3.6.1.4.1.4874.2.2.20.1.8.9.1
An association of a subscriber to an interface location.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniAaaSubscriberLocationEntry  

juniAaaSubscriberLocationLocationIndex 1.3.6.1.4.1.4874.2.2.20.1.8.9.1.1
The value of a platform interface location.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniInterfaceLocationValue  

juniAaaSubscriberLocationHandle 1.3.6.1.4.1.4874.2.2.20.1.8.9.1.2
The subscriber handle associated with this subscriber. A subscriber handle is a monotonically increasing integer.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

juniAaaSubscriberLocationRowStatus 1.3.6.1.4.1.4874.2.2.20.1.8.9.1.3
Always has value 'active'.
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

juniAaaSubscriberPseudoPeakCount 1.3.6.1.4.1.4874.2.2.20.1.8.10
The peak number of pseudo-subscribers. The peak count includes successfully authenticated pseudo-subscribers as well as those pseudo-subscribers in the process of being authenticated. Pseudo-subscribers are those whose identities are locally configured on a dynamic link (e.g. an ATM subinterface) via the (imprecisely named) Juniper-SUBSCRIBER-MIB. Some links (e.g. IPoA) provide no link protocol with which to query the identity of a remote user. In such a case, a locally configured pseudo-subscriber can be used to conduct AAA authentication-based configuration of the dynamic link when it becomes active. Pseudo-subscribers are understood to be intended more for dynamic configuration than for actually identifying the remote user. Consequently, the pseudo-subscribers are not reflected in any of the subscriber tables defined in this MIB.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

juniAaaSubscriberPseudoCount 1.3.6.1.4.1.4874.2.2.20.1.8.11
The current number of pseudo-subscribers. The pseudo-subscriber count includes successfully authenticated subscribers as well as those subscribers in the process of being authenticated. Pseudo-subscribers are those whose identities are locally configured on a dynamic link (e.g. an ATM subinterface) via the (imprecisely named) Juniper-SUBSCRIBER-MIB. Some links (e.g. IPoA) provide no link protocol with which to query the identity of a remote user. In such a case, a locally configured pseudo-subscriber can be used to conduct AAA authentication-based configuration of the dynamic link when it becomes active. Pseudo-subscribers are understood to be intended more for dynamic configuration than for actually identifying the remote user. Consequently, the pseudo-subscribers are not reflected in any of the subscriber tables defined in this MIB.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

juniAaaSubscriberIpv6AddrPrefixTable 1.3.6.1.4.1.4874.2.2.20.1.8.12
The entries in this table represent IPv6 Address Prefixes by subscriber handle value.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniAaaSubscriberIpv6AddrPrefixEntry

juniAaaSubscriberIpv6AddrPrefixEntry 1.3.6.1.4.1.4874.2.2.20.1.8.12.1
A specification of IPv6 Address Prefixes by subscriber handle.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniAaaSubscriberIpv6AddrPrefixEntry  

juniAaaSubscriberIpv6AddrPrefix 1.3.6.1.4.1.4874.2.2.20.1.8.12.1.1
The client IPv6 Address Prefix assigned to this subscriber.
Status: current Access: read-only
OBJECT-TYPE    
  Ipv6AddressPrefix  

juniAaaSubscriberIpv6AddrPrefixSize 1.3.6.1.4.1.4874.2.2.20.1.8.12.1.2
The size of the client IPv6 Address Prefix assigned to this subscriber.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..128  

juniAaaSubscriberExtTable 1.3.6.1.4.1.4874.2.2.20.1.8.13
The entries in this table represent subscribers extension attributes by subscriber handle value.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniAaaSubscriberExtEntry

juniAaaSubscriberInterfaceSummaryTable 1.3.6.1.4.1.4874.2.2.20.1.8.14
The entries in this table report number of subscribers per subscriber interface which includes the port type (1 = atm; 2 = ethernet), slot, port and sub-interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniAaaSubscriberInterfaceSummaryEntry

juniAaaSubscriberInterfaceSummaryEntry 1.3.6.1.4.1.4874.2.2.20.1.8.14.1
A specification of subscribers on an subscriber interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniAaaSubscriberInterfaceSummaryEntry  

juniAaaSubscriberInterfaceSummaryIndex 1.3.6.1.4.1.4874.2.2.20.1.8.14.1.1
The value of a subscriber interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniSubscriberInterfaceValue  

juniAaaSubscriberSubInterfaceSummaryIndex 1.3.6.1.4.1.4874.2.2.20.1.8.14.1.2
The value of a subscriber sub-interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

juniAaaSubscriberInterfaceSummaryCount 1.3.6.1.4.1.4874.2.2.20.1.8.14.1.3
The number of subscribers associated with this subscriber interface.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

juniAaaSubscriberInterfaceTable 1.3.6.1.4.1.4874.2.2.20.1.8.15
The subscriber entries in this table sorted by subscriber interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniAaaSubscriberInterfaceEntry

juniAaaSubscriberInterfaceEntry 1.3.6.1.4.1.4874.2.2.20.1.8.15.1
An association of a subscriber to a subscriber interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniAaaSubscriberInterfaceEntry  

juniAaaSubscriberInterfaceIndex 1.3.6.1.4.1.4874.2.2.20.1.8.15.1.1
The value of a subscriber interface. This includes the port type (1 = ATM; 2 = Ethernet), slot, port, and sub-interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniSubscriberInterfaceValue  

juniAaaSubscriberSubInterfaceIndex 1.3.6.1.4.1.4874.2.2.20.1.8.15.1.2
The value of a subscriber sub-interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

juniAaaSubscriberInterfaceHandle 1.3.6.1.4.1.4874.2.2.20.1.8.15.1.3
The subscriber handle associated with this subscriber interface. A subscriber handle is a monotonically increasing integer.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

juniAaaSubscriberInterfaceRowStatus 1.3.6.1.4.1.4874.2.2.20.1.8.15.1.4
Always has value 'active'.
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

juniAaaSubscriberSlotSummaryTable 1.3.6.1.4.1.4874.2.2.20.1.8.16
The entries in this table report number of subscribers per slot.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniAaaSubscriberSlotSummaryEntry

juniAaaSubscriberSlotSummaryEntry 1.3.6.1.4.1.4874.2.2.20.1.8.16.1
A specification of subscribers for a slot.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniAaaSubscriberSlotSummaryEntry  

juniAaaSubscriberSlotSummarySlotIndex 1.3.6.1.4.1.4874.2.2.20.1.8.16.1.1
The index of the slot.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

juniAaaSubscriberSlotSummaryCount 1.3.6.1.4.1.4874.2.2.20.1.8.16.1.2
The number of subscribers on this slot.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

juniAaaSubscriberSlotTable 1.3.6.1.4.1.4874.2.2.20.1.8.17
The subscriber in this table sorted by slot.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JuniAaaSubscriberSlotEntry

juniAaaSubscriberSlotEntry 1.3.6.1.4.1.4874.2.2.20.1.8.17.1
A specification of subscribers by slot.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniAaaSubscriberSlotEntry  

juniAaaSubscriberSlotIndex 1.3.6.1.4.1.4874.2.2.20.1.8.17.1.1
The index of the slot.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

juniAaaSubscriberSlotHandle 1.3.6.1.4.1.4874.2.2.20.1.8.17.1.2
The subscriber handle associated with this slot. The subscriber handle is a monotonically increasing integer.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

juniAaaSubscriberSlotRowStatus 1.3.6.1.4.1.4874.2.2.20.1.8.17.1.3
Always has value 'active'.
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

juniAaaSubscriberExtEntry 1.3.6.1.4.1.4874.2.2.20.1.8.13.1
A specification of subscribers extension attributes by subscriber handle.
Status: current Access: not-accessible
OBJECT-TYPE    
  JuniAaaSubscriberExtEntry  

juniAaaSubscriberExtUserName 1.3.6.1.4.1.4874.2.2.20.1.8.13.1.1
The user name associated with this subscriber.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

juniAaaSubscriberExtLoginTime 1.3.6.1.4.1.4874.2.2.20.1.8.13.1.2
The time this subscriber logged in using AAA protocol.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

juniAaaSubscriberExtIpAddress 1.3.6.1.4.1.4874.2.2.20.1.8.13.1.3
The client IP Address assigned to this subscriber.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

juniAaaSubscriberExtIpAddressMask 1.3.6.1.4.1.4874.2.2.20.1.8.13.1.4
The client IP Address Mask assigned to this subscriber.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

juniAaaSubscriberExtAddrAssignType 1.3.6.1.4.1.4874.2.2.20.1.8.13.1.5
The address assignment type for this subscriber.
Status: current Access: read-only
OBJECT-TYPE    
  JuniAddressAssignType  

juniAaaSubscriberExtState 1.3.6.1.4.1.4874.2.2.20.1.8.13.1.6
The state of this subscriber.
Status: current Access: read-only
OBJECT-TYPE    
  JuniSubscriberState  

juniAaaSubscriberExtClientType 1.3.6.1.4.1.4874.2.2.20.1.8.13.1.7
The client type for this subscriber. Certain client types (e.g., 'other') might be suppressed from representation in this table.
Status: current Access: read-only
OBJECT-TYPE    
  JuniSubscriberClientType  

juniAaaSubscriberExtAcctSessionId 1.3.6.1.4.1.4874.2.2.20.1.8.13.1.8
Account session ID associated with this subscriber. The value and encoding of this attribute depends on the way AAA protocol is configured. For example it is attribute 44 for RADIUS.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

juniAaaSubscriberExtClass 1.3.6.1.4.1.4874.2.2.20.1.8.13.1.9
Classification attribute associated with this subscriber. The value and encoding of this attribute depends on the way AAA protocol is configured. For example it is attribute 25 for RADIUS.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

juniAaaSubscriberExtNasPort 1.3.6.1.4.1.4874.2.2.20.1.8.13.1.10
Associated NAS port with this subscriber. The value and encoding of this attribute depends on the way AAA protocol is configured. For example it is attribute 5 for RADIUS.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

juniAaaSubscriberExtNasPortType 1.3.6.1.4.1.4874.2.2.20.1.8.13.1.11
Associated NAS port type attribute associated with this subscriber. The value and encoding of this attribute depends on the way AAA protocol is configured. For example it is attribute 61 for RADIUS.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

juniAaaSubscriberExtCalledStationId 1.3.6.1.4.1.4874.2.2.20.1.8.13.1.12
Called ID associated with this subscriber. The value and encoding of this attribute depends on the way AAA protocol is configured. For example it is attribute 30 for RADIUS.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..255)  

juniAaaSubscriberExtCallingStationId 1.3.6.1.4.1.4874.2.2.20.1.8.13.1.13
Calling ID associated with this subscriber. The value and encoding of this attribute depends on the way AAA protocol is configured. For example it is attribute 31 for RADIUS.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..255)  

juniAaaSubscriberExtL2tpTunnelId 1.3.6.1.4.1.4874.2.2.20.1.8.13.1.14
L2TP Tunnel ID associated with this subscriber of concerned LNS. A value 0 for this attribute indicates the terminated subscriber.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

juniAaaAccountingCapability 1.3.6.1.4.1.4874.2.2.20.1.9.1
Indicates whether this system supports AAA Accounting. The value true(1) indicate that it does, false(2) indicates that it does not.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniAaaAddressAssignmentCapability 1.3.6.1.4.1.4874.2.2.20.1.9.2
Indicates whether this system supports AAA address assignment. The value true(1) indicates that it does, false(2) indicates that it does not.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniAaaBrasCapability 1.3.6.1.4.1.4874.2.2.20.1.9.3
Indicates whether this system supports AAA BRAS functionality. The value true(1) indicates that it does, false(2) indicates that it does not.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniAaaTunnelingCapability 1.3.6.1.4.1.4874.2.2.20.1.9.4
Indicates whether this system supports AAA tunneling. The value true(1) indicates that it does, false(2) indicates that it does not.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

juniAaaMIBConformance 1.3.6.1.4.1.4874.2.2.20.4
OBJECT IDENTIFIER    

juniAaaMIBCompliances 1.3.6.1.4.1.4874.2.2.20.4.1
OBJECT IDENTIFIER    

juniAaaMIBGroups 1.3.6.1.4.1.4874.2.2.20.4.2
OBJECT IDENTIFIER    

juniAaaCompliance 1.3.6.1.4.1.4874.2.2.20.4.1.1
Obsolete compliance statement for systems supporting AAA. This statement became obsolete when new objects were added.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

juniAaaCompliance2 1.3.6.1.4.1.4874.2.2.20.4.1.2
Obsolete compliance statement for systems supporting AAA. This statement became obsolete when new objects were added and new groupings were defined.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

juniAaaCompliance3 1.3.6.1.4.1.4874.2.2.20.4.1.3
Obsolete compliance statement for systems supporting AAA. This statement became obsolete when the juniAaaAssignDomainStripDomain object was added to the B-RAS group.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

juniAaaCompliance4 1.3.6.1.4.1.4874.2.2.20.4.1.4
Obsolete compliance statement for systems supporting AAA. This statement became obsolete when new assignment delimiter objects were added to the B-RAS group.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

juniAaaCompliance5 1.3.6.1.4.1.4874.2.2.20.4.1.5
Obsolete compliance statement for systems supporting AAA. This statement became obsolete when the subscriber and capabilities groups were added.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

juniAaaCompliance6 1.3.6.1.4.1.4874.2.2.20.4.1.6
Obsolete compliance statement for systems supporting AAA. This statement became obsolete when support was added for subscriber information by interface location.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

juniAaaCompliance7 1.3.6.1.4.1.4874.2.2.20.4.1.7
Obsolete compliance statement for systems supporting AAA. This statement became obsolete when several new objects were added.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

juniAaaCompliance8 1.3.6.1.4.1.4874.2.2.20.4.1.8
Obsolete compliance statement for systems supporting AAA. This statement became obsolete when new objects were added to the B-RAS and tunnel groups.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

juniAaaCompliance9 1.3.6.1.4.1.4874.2.2.20.4.1.9
Obsolete compliance statement for systems supporting AAA. This statement became obsolete when new objects were added to the B-RAS group.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

juniAaaCompliance10 1.3.6.1.4.1.4874.2.2.20.4.1.10
Obsolete compliance statement for systems supporting AAA. This statement became obsolete when new objects were added to the B-RAS, Subscriber and Address groups.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

juniAaaCompliance11 1.3.6.1.4.1.4874.2.2.20.4.1.11
Obsolete compliance statement for systems supporting AAA.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

juniAaaCompliance12 1.3.6.1.4.1.4874.2.2.20.4.1.12
Obsolete compliance statement for systems supporting AAA.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

juniAaaCompliance13 1.3.6.1.4.1.4874.2.2.20.4.1.13
Obsolete compliance statement for systems supporting AAA.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

juniAaaCompliance14 1.3.6.1.4.1.4874.2.2.20.4.1.14
The compliance statement for systems supporting AAA.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

juniAaaCompliance15 1.3.6.1.4.1.4874.2.2.20.4.1.15
Obsolete compliance statement for systems supporting AAA.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

juniAaaCompliance16 1.3.6.1.4.1.4874.2.2.20.4.1.16
Obsolete compliance statement for systems supporting AAA.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

juniAaaCompliance17 1.3.6.1.4.1.4874.2.2.20.4.1.17
Obsolete compliance statement for systems supporting AAA.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

juniAaaCompliance18 1.3.6.1.4.1.4874.2.2.20.4.1.18
Obsolete compliance statement for systems supporting AAA.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

juniAaaCompliance19 1.3.6.1.4.1.4874.2.2.20.4.1.19
Obsolete compliance statement for systems supporting AAA.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

juniAaaCompliance20 1.3.6.1.4.1.4874.2.2.20.4.1.20
Obsolete compliance statement for systems supporting AAA.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

juniAaaCompliance21 1.3.6.1.4.1.4874.2.2.20.4.1.21
Obsolete compliance statement for systems supporting AAA. This statement became obsolete when the juniAaaMonitorIngressTrafficOnly object was added to the B-RAS group.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

juniAaaCompliance22 1.3.6.1.4.1.4874.2.2.20.4.1.22
Obsolete compliance statement for systems supporting AAA. This statement became obsolete when the juniAaaAssignDomainBackupPoolName object was added to the B-RAS group.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

juniAaaCompliance23 1.3.6.1.4.1.4874.2.2.20.4.1.23
Obsolete compliance statement for systems supporting AAA. This statement became obsolete when juniAaaFramedIpv6PrefixAsIpv6NdRaPrefix and juniAaaDelegatedIpv6PrefixAsDhcpv6DelegatedPrefix objects were added to the B-RAS group.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

juniAaaCompliance24 1.3.6.1.4.1.4874.2.2.20.4.1.24
The compliance statement for systems supporting AAA.
Status: current Access: read-only
MODULE-COMPLIANCE    

juniAaaGroup 1.3.6.1.4.1.4874.2.2.20.4.2.1
Obsolete collection of objects providing management of AAA functionality in a Juniper product. This group became obsolete when new objects were added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniAaaGroup2 1.3.6.1.4.1.4874.2.2.20.4.2.2
Obsolete collection of objects providing management of AAA functionality in a Juniper product. This group became obsolete when new objects were added and new groupings were defined.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniAaaBasicGroup 1.3.6.1.4.1.4874.2.2.20.4.2.3
The basic collection of objects providing management of AAA functionality in a Juniper product.
Status: current Access: read-only
OBJECT-GROUP    

juniAaaBrasGroup 1.3.6.1.4.1.4874.2.2.20.4.2.4
Obsolete collection of objects providing management of AAA B-RAS functionality in a Juniper product. This group became obsolete when the juniAaaAssignDomainStripDomain object was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniAaaTunnelGroup 1.3.6.1.4.1.4874.2.2.20.4.2.5
Obsolete collection of objects providing management of AAA tunneling functionality in a Juniper product. This group became obsolete when the maximum sessions object was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniAaaAuthenticationGroup 1.3.6.1.4.1.4874.2.2.20.4.2.6
Obsolete collection of objects providing management of AAA authentication functionality in a Juniper product. This group became obsolete when the authentication methods table was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniAaaAccountingGroup 1.3.6.1.4.1.4874.2.2.20.4.2.7
Obsolete collection of objects providing management of AAA accounting functionality in a Juniper product. This group became obsolete when the juniAaaAcctSendStopOnAaaDeny object was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniAaaAddressGroup 1.3.6.1.4.1.4874.2.2.20.4.2.8
Obsolete collection of objects providing management of AAA address assignment functionality in a Juniper product. This group became obsolete when IPv6 support was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniAaaBrasGroup2 1.3.6.1.4.1.4874.2.2.20.4.2.9
Obsolete collection of objects providing management of AAA B-RAS functionality in a Juniper product. This group became obsolete when new assignment delimiter objects were added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniAaaBrasGroup3 1.3.6.1.4.1.4874.2.2.20.4.2.10
Obsolete collection of objects providing management of AAA B-RAS functionality in a Juniper product. This group became obsolete when new objects were added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniAaaSubscriberGroup 1.3.6.1.4.1.4874.2.2.20.4.2.11
Obsolete collection of objects providing management of AAA B-RAS Subscriber functionality in a Juniper product. This group became obsolete when support was added for monitoring subscriber information by interface location.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniAaaCapabilitiesGroup 1.3.6.1.4.1.4874.2.2.20.4.2.12
The collection of objects providing management of AAA Capabilities functionality in a Juniper product.
Status: current Access: read-only
OBJECT-GROUP    

juniAaaSubscriberGroup2 1.3.6.1.4.1.4874.2.2.20.4.2.13
Obsolete collection of objects providing management of AAA B-RAS Subscriber functionality in a Juniper product. This group became obsolete when the pseudo-subscriber meters were added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniAaaAccountingGroup2 1.3.6.1.4.1.4874.2.2.20.4.2.14
Obsolete collection of objects providing management of AAA accounting functionality in a Juniper product. This group became obsolete when the accounting methods table was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniAaaBrasGroup4 1.3.6.1.4.1.4874.2.2.20.4.2.15
Obsolete collection of objects providing management of AAA B-RAS functionality in a Juniper product. This group became obsolete when assign domain pool name was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniAaaSubscriberGroup3 1.3.6.1.4.1.4874.2.2.20.4.2.16
Obsoleted collection of objects providing management of AAA B-RAS Subscriber functionality in a Juniper product. This group became obsolete when IPv6 support was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniAaaBrasGroup5 1.3.6.1.4.1.4874.2.2.20.4.2.17
Obsolete collection of objects providing management of AAA B-RAS functionality in a Juniper product. This group became obsolete when PADN support was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniAaaTunnelGroup2 1.3.6.1.4.1.4874.2.2.20.4.2.18
Obsolete collection of objects providing management of AAA tunneling functionality in a Juniper product.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniAaaBrasGroup6 1.3.6.1.4.1.4874.2.2.20.4.2.19
Obsolete collection of objects providing management of AAA B-RAS functionality in a Juniper product. This group became obsolete when IPv6 support was added.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniAaaBrasGroup7 1.3.6.1.4.1.4874.2.2.20.4.2.20
Obsolete collection of objects providing management of AAA B-RAS functionality in a Juniper product.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniAaaAddressGroup2 1.3.6.1.4.1.4874.2.2.20.4.2.21
The collection of objects providing management of AAA address assignment functionality in a Juniper product.
Status: current Access: read-only
OBJECT-GROUP    

juniAaaSubscriberGroup4 1.3.6.1.4.1.4874.2.2.20.4.2.22
Obsolete collection of objects providing management of AAA B-RAS Subscriber functionality in a Juniper product.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniAaaSubscriberGroup5 1.3.6.1.4.1.4874.2.2.20.4.2.31
The collection of objects providing management of AAA B-RAS Subscriber functionality in a Juniper product.
Status: current Access: read-only
OBJECT-GROUP    

juniAaaBrasGroup8 1.3.6.1.4.1.4874.2.2.20.4.2.23
Obsolete collection of objects providing management of AAA B-RAS functionality in a Juniper product.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniAaaBrasGroup9 1.3.6.1.4.1.4874.2.2.20.4.2.24
Obsolete collection of objects providing management of AAA B-RAS functionality in a Juniper product.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniAaaTunnelGroup3 1.3.6.1.4.1.4874.2.2.20.4.2.25
Obsolete collection of objects providing management of AAA tunneling functionality in a Juniper product.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniAaaAccountingGroup3 1.3.6.1.4.1.4874.2.2.20.4.2.26
Obsolete collection of objects providing management of AAA accounting functionality in a Juniper product.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniAaaAuthenticationGroup2 1.3.6.1.4.1.4874.2.2.20.4.2.27
Obsolete collection of objects providing management of AAA authentication functionality in a Juniper product.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniAaaAuthenticationGroup3 1.3.6.1.4.1.4874.2.2.20.4.2.28
The collection of objects providing management of AAA authentication functionality in a Juniper product.
Status: current Access: read-only
OBJECT-GROUP    

juniAaaAccountingGroup4 1.3.6.1.4.1.4874.2.2.20.4.2.29
The collection of objects providing management of AAA accounting functionality in a Juniper product.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniAaaTunnelGroup4 1.3.6.1.4.1.4874.2.2.20.4.2.30
Obsolete collection of objects providing management of AAA tunneling functionality in a Juniper product.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniAaaBrasGroup10 1.3.6.1.4.1.4874.2.2.20.4.2.32
Obsolete collection of objects providing management of AAA B-RAS functionality in a Juniper product.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniAaaTunnelGroup5 1.3.6.1.4.1.4874.2.2.20.4.2.33
The collection of collection of objects providing management of AAA tunneling functionality in a Juniper product.
Status: current Access: read-only
OBJECT-GROUP    

juniAaaBrasGroup11 1.3.6.1.4.1.4874.2.2.20.4.2.34
The obsolete collection of objects providing management of AAA B-RAS functionality in a Juniper product.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniAaaAccountingGroup5 1.3.6.1.4.1.4874.2.2.20.4.2.35
The collection of objects providing management of AAA accounting functionality in a Juniper product.
Status: current Access: read-only
OBJECT-GROUP    

juniAaaBrasGroup12 1.3.6.1.4.1.4874.2.2.20.4.2.36
The obsolete collection of objects providing management of AAA B-RAS functionality in a Juniper product.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniAaaBrasGroup13 1.3.6.1.4.1.4874.2.2.20.4.2.37
The obsolete collection of objects providing management of AAA B-RAS functionality in a Juniper product.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniAaaBrasGroup14 1.3.6.1.4.1.4874.2.2.20.4.2.38
The obsolete collection of objects providing management of AAA B-RAS functionality in a Juniper product.
Status: obsolete Access: read-only
OBJECT-GROUP    

juniAaaBrasGroup15 1.3.6.1.4.1.4874.2.2.20.4.2.39
The collection of objects providing management of AAA B-RAS functionality in a Juniper product.
Status: current Access: read-only
OBJECT-GROUP