JUNIPER-PW-ATM-MIB

File: JUNIPER-PW-ATM-MIB.mib (31310 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
PerfHist-TC-MIB JUNIPER-SMI JUNIPER-VPN-MIB
IF-MIB ATM-TC-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Counter32
Counter64 Unsigned32 mib-2
MODULE-COMPLIANCE OBJECT-GROUP TruthValue
RowStatus RowPointer PerfCurrentCount
PerfIntervalCount jnxMibs jnxVpnPwVpnType
jnxVpnPwVpnName jnxVpnPwIndex InterfaceIndex
AtmVpIdentifier AtmVcIdentifier

Defined Types

JnxPwAtmCfgEntry  
SEQUENCE    
  jnxpwAtmCfgMaxCellConcatenation Unsigned32
  jnxpwAtmCfgFarEndMaxCellConcatenation Unsigned32
  jnxpwAtmCfgTimeoutMode INTEGER
  jnxpwAtmClpQosMapping TruthValue

JnxPwAtmOutboundNto1Entry  
SEQUENCE    
  jnxpwAtmOutboundNto1AtmIf InterfaceIndex
  jnxpwAtmOutboundNto1Vpi AtmVpIdentifier
  jnxpwAtmOutboundNto1Vci AtmVcIdentifier
  jnxpwAtmOutboundNto1RowStatus RowStatus
  jnxpwAtmOutboundNto1TrafficParamDescr RowPointer
  jnxpwAtmOutboundNto1MappedVpi AtmVpIdentifier
  jnxpwAtmOutboundNto1MappedVci AtmVcIdentifier

JnxPwAtmInboundNto1Entry  
SEQUENCE    
  jnxpwAtmInboundNto1AtmIf InterfaceIndex
  jnxpwAtmInboundNto1Vpi AtmVpIdentifier
  jnxpwAtmInboundNto1Vci AtmVcIdentifier
  jnxpwAtmInboundNto1RowStatus RowStatus
  jnxpwAtmInboundNto1TrafficParamDescr RowPointer
  jnxpwAtmInboundNto1MappedVpi AtmVpIdentifier
  jnxpwAtmInboundNto1MappedVci AtmVcIdentifier

JnxPwAtmPerfCurrentEntry  
SEQUENCE    
  jnxpwAtmPerfCurrentMissingPkts PerfCurrentCount
  jnxpwAtmPerfCurrentPktsReOrder PerfCurrentCount
  jnxpwAtmPerfCurrentPktsMisOrder PerfCurrentCount
  jnxpwAtmPerfCurrentPktsTimeout PerfCurrentCount
  jnxpwAtmPerfCurrentPktsXmit Counter64
  jnxpwAtmPerfCurrentCellsDropped PerfCurrentCount
  jnxpwAtmPerfCurrentPktsReceived Counter64
  jnxpwAtmPerfCurrentUnknownCells Counter64

JnxPwAtmPerfIntervalEntry  
SEQUENCE    
  jnxpwAtmPerfIntervalNumber Unsigned32
  jnxpwAtmPerfIntervalValidData TruthValue
  jnxpwAtmPerfIntervalDuration Unsigned32
  jnxpwAtmPerfIntervalMissingPkts PerfIntervalCount
  jnxpwAtmPerfIntervalPktsReOrder PerfIntervalCount
  jnxpwAtmPerfIntervalPktsMisOrder PerfIntervalCount
  jnxpwAtmPerfIntervalPktsTimeout PerfIntervalCount
  jnxpwAtmPerfIntervalPktsXmit Counter64
  jnxpwAtmPerfIntervalCellsDropped PerfIntervalCount
  jnxpwAtmPerfIntervalPktsReceived Counter64
  jnxpwAtmPerfIntervalUnknownCells Counter64

JnxPwAtmPerf1DayIntervalEntry  
SEQUENCE    
  jnxpwAtmPerf1DayIntervalNumber Unsigned32
  jnxpwAtmPerf1DayIntervalValidData TruthValue
  jnxpwAtmPerf1DayIntervalDuration Unsigned32
  jnxpwAtmPerf1DayIntervalMissingPkts Counter32
  jnxpwAtmPerf1DayIntervalPktsReOrder Counter32
  jnxpwAtmPerf1DayIntervalPktsMisOrder Counter32
  jnxpwAtmPerf1DayIntervalPktsTimeout Counter32
  jnxpwAtmPerf1DayIntervalPktsXmit Counter64
  jnxpwAtmPerf1DayIntervalCellsDropped Counter32
  jnxpwAtmPerf1DayIntervalPktsReceived Counter64
  jnxpwAtmPerf1DayIntervalUnknownCells Counter64

Defined Values

jnxPWAtmMIB 1.3.6.1.4.1.2636.3.57
This MIB module defines objects used for managing the atm pseudowires in Juniper products.
MODULE-IDENTITY    

jnxpwAtmNotifications 1.3.6.1.4.1.2636.3.57.0
OBJECT IDENTIFIER    

jnxpwAtmObjects 1.3.6.1.4.1.2636.3.57.1
OBJECT IDENTIFIER    

jnxpwAtmConformance 1.3.6.1.4.1.2636.3.57.2
OBJECT IDENTIFIER    

jnxpwAtmCfgTable 1.3.6.1.4.1.2636.3.57.1.1
This table specifies generic information for an ATM PW to be carried over PSN in any mode.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxPwAtmCfgEntry

jnxpwAtmCfgEntry 1.3.6.1.4.1.2636.3.57.1.1.1
This table contains a set of parameters for the ATM PW that needs to be adapted and carried over PSN. This table is indexed by pwIndex from pwTable. An entry is created for every newly ATM type associated pwIndex in the pwTable. Unless otherwise specified, all read-write objects in this table MAY be changed when the PW is defined as not active and all RW objects values must persist after reboot
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxPwAtmCfgEntry  

jnxpwAtmCfgMaxCellConcatenation 1.3.6.1.4.1.2636.3.57.1.1.1.1
The maximum number of ATM cells that can be concatenated into one PW packet towards PSN. In non LDP or other signaling protocol environment, this object MAY be changed at anytime, but traffic might be interuppted, otherwise, it may be changed when PW is not active.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..29  

jnxpwAtmCfgFarEndMaxCellConcatenation 1.3.6.1.4.1.2636.3.57.1.1.1.2
The maximum number of ATM cells that can be concatenated into one PW packet towards PSN as reported by the far end. If no LDP in use, the object will either return value 0 or allow setting it for calculating protocol overhead.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..29  

jnxpwAtmCfgTimeoutMode 1.3.6.1.4.1.2636.3.57.1.1.1.3
This objects determines whether a packet can be transmitted to the PSN based on time out expiration for collecting cells or not. The actual handling of the time out is implementation specific-as such this object may be changed at any time under proper consideration of traffic interupption effect.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(1), disabled(2), enabled(3)  

jnxpwAtmClpQosMapping 1.3.6.1.4.1.2636.3.57.1.1.1.4
This Object indicates whether the CLP bits should be considered when setting the value in the Quality of Service fields of the encapsulating protocol (e.g. EXP fields of the MPLS Label Stack). Selecting True allows the drop precedence to be preserved across the PSN. In transparent cell transport, the value of this object MUST be false(2), in other cases it can be changed at any time.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

jnxpwAtmOutboundNto1Table 1.3.6.1.4.1.2636.3.57.1.2
This table specifies the information for an ATM PW to be carried over PSN in the outbound direction. Up to N entries can be created in this table for every entry in the pwTable with a pwType equal to: atmCellNto1Vcc(9), or atmCellNto1Vpc(10). An entry can be created only when the VP/VC are known. A single entry will be created in this table for every entry in the pwTable with a pwType equal to one of the following: atmCell1to1Vcc(12), or atmCell1to1Vpc(13), or atmAal5PduVcc(14), or atmAal5SduVcc(2), or atmTransparent(3).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxPwAtmOutboundNto1Entry

jnxpwAtmOutboundNto1Entry 1.3.6.1.4.1.2636.3.57.1.2.1
A row in this table represents an ATM PW that needs to be adapted and carried over PSN. This table is indexed by pwIndex from pwTable and the ATM interface with VPL/ VCLs. In atmTransparent(3), Vpi and VCi will be 0xFFFF during set operation. Unless otherwise specified, all read-create objects in this table MUST NOT be changed after row activation and SHOULD remain unchanged after reboot.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxPwAtmOutboundNto1Entry  

jnxpwAtmOutboundNto1AtmIf 1.3.6.1.4.1.2636.3.57.1.2.1.1
The ATM Interface that receives cells from the ATM network.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

jnxpwAtmOutboundNto1Vpi 1.3.6.1.4.1.2636.3.57.1.2.1.2
VPI value of this ATM PW. In atmTransparent(3), Vpi will be the equivalent of 0xFFFF
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmVpIdentifier  

jnxpwAtmOutboundNto1Vci 1.3.6.1.4.1.2636.3.57.1.2.1.3
VCI value of this ATM PW. In atmTransparent(3), or VP case, the value will be the equivalent of 0xFFFF
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmVcIdentifier  

jnxpwAtmOutboundNto1RowStatus 1.3.6.1.4.1.2636.3.57.1.2.1.4
This Object is used to create, modify or delete a row in this table.
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

jnxpwAtmOutboundNto1TrafficParamDescr 1.3.6.1.4.1.2636.3.57.1.2.1.5
This object represents a pointer to a ATM traffic parameter specific row in either private or standard table which will be employed while receiving cells from the ATM network. This table should contain a set of self-consistent ATM traffic parameters including the ATM traffic service category. A value of 0.0 indicates Best Effort.
Status: current Access: read-only
OBJECT-TYPE    
  RowPointer  

jnxpwAtmOutboundNto1MappedVpi 1.3.6.1.4.1.2636.3.57.1.2.1.6
The egress generated VPI value of this ATM PW. The entry is valid for PW type of atmCellNto1Vcc(9), atmCellNto1Vpc(10), atmCell1to1Vcc(12), or atmCell1to1Vpc(13). In other types, the value will be the equivalent of 0xFFFF. Value MAY be changed when the PW is defined as not active
Status: current Access: read-only
OBJECT-TYPE    
  AtmVpIdentifier  

jnxpwAtmOutboundNto1MappedVci 1.3.6.1.4.1.2636.3.57.1.2.1.7
The egress generated VCI value of this ATM PW. The entry is valid for PW type of atmCellNto1Vcc(9), atmCellNto1Vpc(10), atmCell1to1Vcc(12), or atmCell1to1Vpc(13. In VP case or other types, the value will be the equivalent of 0xFFFF. Value MAY be changed when the PW is defined as not active.
Status: current Access: read-only
OBJECT-TYPE    
  AtmVcIdentifier  

jnxpwAtmInboundNto1Table 1.3.6.1.4.1.2636.3.57.1.3
This table specifies the information for an ATM PW to be carried over PSN in the Inbound direction. Up to N entries can be created in this table for every entry in the pwTable with a pwType equal to: atmCellNto1Vcc(9), or atmCellNto1Vpc(10). An entry can be created only when the VP/VC are known. A single entry will be created in this table for every entry in the pwTable with a pwType equal to one of the following:atmCell1to1Vcc(12), or atmCell1to1Vpc(13), or atmAal5PduVcc(14), or atmAal5SduVcc(2), or atmTransparent(3).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxPwAtmInboundNto1Entry

jnxpwAtmInboundNto1Entry 1.3.6.1.4.1.2636.3.57.1.3.1
A row in this table represents an ATM PW that needs to be adapted and carried over PSN. This table is indexed by pwIndex from pwTable and the ATM interface with VPL/ VCLs. In atmTransparent(3), Vpi and VCi will be 0xFFFF during set operation. Unless otherwise specified, all Read-Creat objects in this table MUST NOT be changed after row activation and SHOULD remain unchanged after reboot.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxPwAtmInboundNto1Entry  

jnxpwAtmInboundNto1AtmIf 1.3.6.1.4.1.2636.3.57.1.3.1.1
The ATM Interface that receives cells from the ATM network.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

jnxpwAtmInboundNto1Vpi 1.3.6.1.4.1.2636.3.57.1.3.1.2
VPI value of this ATM PW. In atmTransparent(3), Vpi will be the equivalent of 0xFFFF.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmVpIdentifier  

jnxpwAtmInboundNto1Vci 1.3.6.1.4.1.2636.3.57.1.3.1.3
VCI value of this ATM PW. In atmTransparent(3), or VP case, the value will be the equivalent of 0xFFFF
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmVcIdentifier  

jnxpwAtmInboundNto1RowStatus 1.3.6.1.4.1.2636.3.57.1.3.1.4
This Object is used to create, modify or delete a row in this table.
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

jnxpwAtmInboundNto1TrafficParamDescr 1.3.6.1.4.1.2636.3.57.1.3.1.5
This object represents a pointer to a ATM traffic parameter specific row in either private or standard table which will be employed while receiving cells from the ATM network. This table should contain a set of self-consistent ATM traffic parameters including the ATM traffic service category. A value of 0.0 indicates Best Effort.
Status: current Access: read-only
OBJECT-TYPE    
  RowPointer  

jnxpwAtmInboundNto1MappedVpi 1.3.6.1.4.1.2636.3.57.1.3.1.6
The generated VPI value of this ATM PW. The entry is valid for PW type of atmCellNto1Vcc(9), atmCellNto1Vpc(10), atmCell1to1Vcc(12), or atmCell1to1Vpc(13). In other types, the value will be the equivalent of 0xFFFF. Value MAY be changed when the PW is defined as not active.
Status: current Access: read-only
OBJECT-TYPE    
  AtmVpIdentifier  

jnxpwAtmInboundNto1MappedVci 1.3.6.1.4.1.2636.3.57.1.3.1.7
The generated VCI value of this ATM PW. The entry is valid for PW type of atmCellNto1Vcc(9), atmCellNto1Vpc(10), atmCell1to1Vcc(12), or atmCell1to1Vpc(13. In VP case or other types, the value will be the equivalent of 0xFFFF. Value MAY be changed when the PW is defined as not active.
Status: current Access: read-only
OBJECT-TYPE    
  AtmVcIdentifier  

jnxpwAtmPerfCurrentTable 1.3.6.1.4.1.2636.3.57.1.4
The current 15 minute interval counts are in this table. This table provides performance information per ATM PW.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxPwAtmPerfCurrentEntry

jnxpwAtmPerfCurrentEntry 1.3.6.1.4.1.2636.3.57.1.4.1
An entry in this table is created by the agent for every pwAtmCfgTable entry. After 15 minutes, the contents of this table entry are copied to a new entry in the pwAtmPerfInterval table and the counts in this entry are reset to zero.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxPwAtmPerfCurrentEntry  

jnxpwAtmPerfCurrentMissingPkts 1.3.6.1.4.1.2636.3.57.1.4.1.1
Number of missing packets (as detected via control word sequence number gaps).
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

jnxpwAtmPerfCurrentPktsReOrder 1.3.6.1.4.1.2636.3.57.1.4.1.2
Number of packets detected out of sequence (via control word sequence number), but successfully re-ordered. Note: some implementations may not support this Feature.
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

jnxpwAtmPerfCurrentPktsMisOrder 1.3.6.1.4.1.2636.3.57.1.4.1.3
Number of packets detected out of order (via control word sequence numbers).
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

jnxpwAtmPerfCurrentPktsTimeout 1.3.6.1.4.1.2636.3.57.1.4.1.4
Number of packets transmitted due to timeout expiration while attempting to collect cells.
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

jnxpwAtmPerfCurrentPktsXmit 1.3.6.1.4.1.2636.3.57.1.4.1.5
Number of transmitted packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

jnxpwAtmPerfCurrentCellsDropped 1.3.6.1.4.1.2636.3.57.1.4.1.6
Number of dropped cells.
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

jnxpwAtmPerfCurrentPktsReceived 1.3.6.1.4.1.2636.3.57.1.4.1.7
Number of received packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

jnxpwAtmPerfCurrentUnknownCells 1.3.6.1.4.1.2636.3.57.1.4.1.8
Number of cells received from the PSN with unknown VPI or VCI values. This object is relevant only in N:1 mode.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

jnxpwAtmPerfIntervalTable 1.3.6.1.4.1.2636.3.57.1.5
This table provides performance information per ATM PW similar to the pwAtmPerfCurrentTable above. However, these counts represent historical 15 minute intervals. Typically, this table will have a maximum of 96 entries for a 24 hour period.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxPwAtmPerfIntervalEntry

jnxpwAtmPerfIntervalEntry 1.3.6.1.4.1.2636.3.57.1.5.1
An entry in this table is created by the agent for every pwAtmPerfCurrentEntry that is 15 minutes old. The contents of the Current entry are copied to the new entry here. The Current entry, then resets its counts to zero for the next current 15 minute interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxPwAtmPerfIntervalEntry  

jnxpwAtmPerfIntervalNumber 1.3.6.1.4.1.2636.3.57.1.5.1.1
A number (normally between 1 and 96 to cover a 24 hour period) which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1. The minimum range of N is 1 through 4. The default range is 1 through 32. The maximum value of N is 96.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..96  

jnxpwAtmPerfIntervalValidData 1.3.6.1.4.1.2636.3.57.1.5.1.2
This variable indicates if the data for this interval is valid.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

jnxpwAtmPerfIntervalDuration 1.3.6.1.4.1.2636.3.57.1.5.1.3
The duration of a particular interval in seconds, Adjustments in the system's time-of-day clock, may cause the interval to be greater or less than, the normal value. Therefore this actual interval value is provided.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxpwAtmPerfIntervalMissingPkts 1.3.6.1.4.1.2636.3.57.1.5.1.4
Number of missing packets (as detected via control word sequence number gaps).
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

jnxpwAtmPerfIntervalPktsReOrder 1.3.6.1.4.1.2636.3.57.1.5.1.5
Number of packets detected out of sequence (via control word sequence number), but successfully re-ordered. Note: some implementations may not support this Feature.
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

jnxpwAtmPerfIntervalPktsMisOrder 1.3.6.1.4.1.2636.3.57.1.5.1.6
Number of packets detected out of order (via control word sequence numbers).
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

jnxpwAtmPerfIntervalPktsTimeout 1.3.6.1.4.1.2636.3.57.1.5.1.7
Number of packets transmitted due to timeout expiration.
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

jnxpwAtmPerfIntervalPktsXmit 1.3.6.1.4.1.2636.3.57.1.5.1.8
Number of transmitted packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

jnxpwAtmPerfIntervalCellsDropped 1.3.6.1.4.1.2636.3.57.1.5.1.9
Number of dropped cells.
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

jnxpwAtmPerfIntervalPktsReceived 1.3.6.1.4.1.2636.3.57.1.5.1.10
Number of received packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

jnxpwAtmPerfIntervalUnknownCells 1.3.6.1.4.1.2636.3.57.1.5.1.11
Number of cells received from the PSN with unknown VPI or VCI values. This object is relevant only in N:1 mode.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

jnxpwAtmPerf1DayIntervalTable 1.3.6.1.4.1.2636.3.57.1.6
This table provides performance information per ATM PW similar to the pwAtmPerfIntervalTable above. However, these counters represent historical 1 day intervals up to one full month.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxPwAtmPerf1DayIntervalEntry

jnxpwAtmPerf1DayIntervalEntry 1.3.6.1.4.1.2636.3.57.1.6.1
An entry is created in this table by the agent for every entry in the pwAtmCfgTable table.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxPwAtmPerf1DayIntervalEntry  

jnxpwAtmPerf1DayIntervalNumber 1.3.6.1.4.1.2636.3.57.1.6.1.1
The number of interval, where 1 indicates current day measured period and 2 and above indicate previous days respectively
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..365  

jnxpwAtmPerf1DayIntervalValidData 1.3.6.1.4.1.2636.3.57.1.6.1.2
This object indicates if the data for this interval is valid.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

jnxpwAtmPerf1DayIntervalDuration 1.3.6.1.4.1.2636.3.57.1.6.1.3
The duration of a particular interval in seconds, Adjustments in the system's time-of-day clock, may cause the interval to be greater or less than, the normal value. Therefore this actual interval value is provided.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxpwAtmPerf1DayIntervalMissingPkts 1.3.6.1.4.1.2636.3.57.1.6.1.4
Number of missing packets (as detected via control word sequence number gaps).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

jnxpwAtmPerf1DayIntervalPktsReOrder 1.3.6.1.4.1.2636.3.57.1.6.1.5
Number of packets detected out of sequence (via control word sequence number), but successfully re-ordered. Note: some implementations may not support this feature.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

jnxpwAtmPerf1DayIntervalPktsMisOrder 1.3.6.1.4.1.2636.3.57.1.6.1.6
Number of packets detected out of order(via control word sequence numbers), and could not be re-ordered.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

jnxpwAtmPerf1DayIntervalPktsTimeout 1.3.6.1.4.1.2636.3.57.1.6.1.7
Number of packets transmitted due to timeout expiration.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

jnxpwAtmPerf1DayIntervalPktsXmit 1.3.6.1.4.1.2636.3.57.1.6.1.8
Number of transmitted packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

jnxpwAtmPerf1DayIntervalCellsDropped 1.3.6.1.4.1.2636.3.57.1.6.1.9
Number of dropped cells.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

jnxpwAtmPerf1DayIntervalPktsReceived 1.3.6.1.4.1.2636.3.57.1.6.1.10
Number of received packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

jnxpwAtmPerf1DayIntervalUnknownCells 1.3.6.1.4.1.2636.3.57.1.6.1.11
Number of cells received from the PSN with unknown VPI or VCI value. This object is relevant only in N:1 mode.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64