JUNIPER-PING-MIB

File: JUNIPER-PING-MIB.mib (59510 bytes)

Imported modules

SNMPv2-SMI IF-MIB SNMP-FRAMEWORK-MIB
SNMPv2-TC DISMAN-PING-MIB INET-ADDRESS-MIB
JUNIPER-SMI

Imported symbols

MODULE-IDENTITY OBJECT-TYPE OBJECT-IDENTITY
Unsigned32 NOTIFICATION-TYPE InterfaceIndexOrZero
SnmpAdminString DisplayString DateAndTime
TruthValue pingResultsEntry pingProbeHistoryEntry
pingCtlTargetAddressType pingCtlTargetAddress pingResultsOperStatus
pingResultsIpTargetAddressType pingResultsIpTargetAddress pingResultsMinRtt
pingResultsMaxRtt pingResultsAverageRtt pingResultsProbeResponses
pingResultsSentProbes pingResultsRttSumOfSquares pingResultsLastGoodProbe
OperationResponseStatus InetPortNumber jnxMibs
jnxPingNotifications

Defined Types

JnxPingCtlEntry  
SEQUENCE    
  jnxPingCtlOwnerIndex SnmpAdminString
  jnxPingCtlTestName SnmpAdminString
  jnxPingCtlIfName DisplayString
  jnxPingCtlRoutingIfIndex InterfaceIndexOrZero
  jnxPingCtlRoutingIfName DisplayString
  jnxPingCtlRoutingInstanceName DisplayString
  jnxPingCtlRttThreshold Unsigned32
  jnxPingCtlRttStdDevThreshold Unsigned32
  jnxPingCtlRttJitterThreshold Unsigned32
  jnxPingCtlEgressTimeThreshold Unsigned32
  jnxPingCtlEgressStdDevThreshold Unsigned32
  jnxPingCtlEgressJitterThreshold Unsigned32
  jnxPingCtlIngressTimeThreshold Unsigned32
  jnxPingCtlIngressStddevThreshold Unsigned32
  jnxPingCtlIngressJitterThreshold Unsigned32
  jnxPingCtlTrapGeneration BITS
  jnxPingCtlTargetPort InetPortNumber
  jnxPingCtlJseriesHWTimeStamp TruthValue
  jnxPingCtlOneWayHWTimeStamp TruthValue
  jnxPingCtlMovAvgSize Unsigned32
  jnxPingCtlMXseriesHWTimeStamp TruthValue
  jnxPingCtlEXseriesHWTimeStamp TruthValue

JnxPingResultsEntry  
SEQUENCE    
  jnxPingResultsRttUs Unsigned32
  jnxPingResultsSumRttUs Unsigned32
  jnxPingResultsMinRttUs Unsigned32
  jnxPingResultsMaxRttUs Unsigned32
  jnxPingResultsAvgRttUs Unsigned32
  jnxPingResultsStdDevRttUs Unsigned32
  jnxPingResultsEgressUs Unsigned32
  jnxPingResultsMinEgressUs Unsigned32
  jnxPingResultsMaxEgressUs Unsigned32
  jnxPingResultsAvgEgressUs Unsigned32
  jnxPingResultsStddevEgressUs Unsigned32
  jnxPingResultsIngressUs Unsigned32
  jnxPingResultsMinIngressUs Unsigned32
  jnxPingResultsMaxIngressUs Unsigned32
  jnxPingResultsAvgIngressUs Unsigned32
  jnxPingResultsStddevIngressUs Unsigned32
  jnxPingResultsJitterRttUs Unsigned32
  jnxPingResultsJitterEgressUs Unsigned32
  jnxPingResultsJitterIngressUs Unsigned32
  jnxPingResultsStatus OperationResponseStatus
  jnxPingResultsTime DateAndTime
  jnxPingResultsOwnerIndex SnmpAdminString
  jnxPingResultsTestName SnmpAdminString

JnxPingProbeHistoryEntry  
SEQUENCE    
  jnxPingProbeHistoryResponseUs Unsigned32
  jnxPingProbeHistoryJitterUs Unsigned32
  jnxPingProbeHistoryResponseEgressUs Unsigned32
  jnxPingProbeHistoryResponseIngressUs Unsigned32
  jnxPingProbeHistoryEgressJitterUs Unsigned32
  jnxPingProbeHistoryIngressJitterUs Unsigned32

JnxPingLastTestResultEntry  
SEQUENCE    
  jnxPingLastTestResultProbeResponses Unsigned32
  jnxPingLastTestResultSentProbes Unsigned32
  jnxPingLastTestResultSumRttUs Unsigned32
  jnxPingLastTestResultMinRttUs Unsigned32
  jnxPingLastTestResultMaxRttUs Unsigned32
  jnxPingLastTestResultAvgRttUs Unsigned32
  jnxPingLastTestResultStdDevRttUs Unsigned32
  jnxPingLastTestResultMinEgressUs Unsigned32
  jnxPingLastTestResultMaxEgressUs Unsigned32
  jnxPingLastTestResultAvgEgressUs Unsigned32
  jnxPingLastTestResultStddevEgressUs Unsigned32
  jnxPingLastTestResultMinIngressUs Unsigned32
  jnxPingLastTestResultMaxIngressUs Unsigned32
  jnxPingLastTestResultAvgIngressUs Unsigned32
  jnxPingLastTestResultStddevIngressUs Unsigned32
  jnxPingLastTestResultPeakToPeakJitterRttUs Unsigned32
  jnxPingLastTestResultPeakToPeakJitterEgressUs Unsigned32
  jnxPingLastTestResultPeakToPeakJitterIngressUs Unsigned32
  jnxPingLastTestResultTime DateAndTime

Defined Values

jnxPingMIB 1.3.6.1.4.1.2636.3.7
This is Juniper Networks' implementation of enterprise specific portions of pingMib. Any data stored in this MIB has directly related entries in mib-2, pingMIB.
MODULE-IDENTITY    

jnxPingObjects 1.3.6.1.4.1.2636.3.7.1
OBJECT IDENTIFIER    

jnxPingImplementationTypeDomains 1.3.6.1.4.1.2636.3.7.2
OBJECT IDENTIFIER    

jnxPingIcmpTimeStamp 1.3.6.1.4.1.2636.3.7.2.1
Indicates that an implementation is using the Internet Control Message Protocol (ICMP) 'TimeStamp' facility. This probe-type provides egress and ingress delay measurements.
Status: current Access: accessible-for-notify
OBJECT-IDENTITY    

jnxPingHttpGet 1.3.6.1.4.1.2636.3.7.2.2
Indicates that an implementation is using an HTTP GET query to calculate a round trip time.
Status: current Access: accessible-for-notify
OBJECT-IDENTITY    

jnxPingHttpGetMetadata 1.3.6.1.4.1.2636.3.7.2.3
Indicates that an implementation is using an HTTP GET Metadata query to calculate a round trip time.
Status: current Access: accessible-for-notify
OBJECT-IDENTITY    

jnxPingDnsQuery 1.3.6.1.4.1.2636.3.7.2.4
Indicates that an implementation is using a DNS query to calculate a round trip time.
Status: current Access: accessible-for-notify
OBJECT-IDENTITY    

jnxPingNtpQuery 1.3.6.1.4.1.2636.3.7.2.5
Indicates that an implementation is using an NTP query to calculate a round trip time.
Status: current Access: accessible-for-notify
OBJECT-IDENTITY    

jnxPingUdpTimestamp 1.3.6.1.4.1.2636.3.7.2.6
Indicates that an implementation is using a UDP timestamp query to calculate a round trip time. This probe-type provides egress and ingress delay measurements
Status: current Access: accessible-for-notify
OBJECT-IDENTITY    

jnxPingCtlTable 1.3.6.1.4.1.2636.3.7.1.2
Defines the jnxPing Control Table for providing enterprise specific options to the corresponding pingCtlTable entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxPingCtlEntry

jnxPingCtlEntry 1.3.6.1.4.1.2636.3.7.1.2.1
Defines an entry in the jnxPingCtlTable. This essentially augments the pingCtlTable with additional objects.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxPingCtlEntry  

jnxPingCtlOwnerIndex 1.3.6.1.4.1.2636.3.7.1.2.1.1
To facilitate the provisioning of access control by a security administrator using the View-Based Access Control Model (RFC 2575, VACM) for tables in which multiple users may need to independently create or modify entries, the initial index is used as an 'owner index'. Such an initial index has a syntax of SnmpAdminString, and can thus be trivially mapped to a securityName or groupName as defined in VACM, in accordance with a security policy. When used in conjunction with such a security policy all entries in the table belonging to a particular user (or group) will have the same value for this initial index. For a given user's entries in a particular table, the object identifiers for the information in these entries will have the same subidentifiers (except for the 'column' subidentifier) up to the end of the encoded owner index. To configure VACM to permit access to this portion of the table, one would create vacmViewTreeFamilyTable entries with the value of vacmViewTreeFamilySubtree including the owner index portion, and vacmViewTreeFamilyMask 'wildcarding' the column subidentifier. More elaborate configurations are possible.
Status: current Access: not-accessible
OBJECT-TYPE    
  SnmpAdminString Size(0..32)  

jnxPingCtlTestName 1.3.6.1.4.1.2636.3.7.1.2.1.2
The name of the ping test. This is locally unique, within the scope of an pingCtlOwnerIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  SnmpAdminString Size(0..32)  

jnxPingCtlIfName 1.3.6.1.4.1.2636.3.7.1.2.1.3
Setting this object to an interface name prior to starting a remote ping operation directs the ping probes to be transmitted over the specified interface. To specify the interface index instead, see pingCtlIfIndex. The interface name must be specified under interfaces statement of the JUNOS configuration. A zero length string value for this object means that this option is not enabled. The following values may be set simultaneously, however, only one value is used. The precedence order is a follows: pingCtlIfIndex (see pingCtlTable in pingMIB) jnxPingCtlIfName jnxPingCtlRoutingIfIndex (deprecated) jnxPingCtlRoutingIfName (deprecated) jnxPingCtlRoutingInstanceName
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..24)  

jnxPingCtlRoutingIfIndex 1.3.6.1.4.1.2636.3.7.1.2.1.4
Use this option to specify the routing instance used when directing outgoing ping packets. The interface ifIndex specified should be in the desired routing instance table. The interface specified will not necessarily be the interface packets are transmitted on. By default, the source address of the packets will be set to the address of the interface chosen. pingCtlSourceAddress should be used to override the choice for source address if necessary. A value of zero for this object means that this option is not enabled. NOTE: deprecated by jnxPingCtlRoutingInstanceName
Status: deprecated Access: read-create
OBJECT-TYPE    
  InterfaceIndexOrZero  

jnxPingCtlRoutingIfName 1.3.6.1.4.1.2636.3.7.1.2.1.5
Use this option to specify the routing instance used when directing outgoing ping packets. The interface name specified should be in the desired routing instance table. The interface specified will not necessarily be the interface packets are transmitted on. By default, the source address of the packets will be set to the address of the interface chosen. pingCtlSourceAddress should be used to override the choice for source address if necessary. NOTE: deprecated by jnxPingCtlRoutingInstanceName
Status: deprecated Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..24)  

jnxPingCtlRoutingInstanceName 1.3.6.1.4.1.2636.3.7.1.2.1.6
Use this option to specify the name of the routing instance used when directing outgoing ping packets. The instance name specified must be configured under routing-instances of the JUNOS configuration.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..31)  

jnxPingCtlRttThreshold 1.3.6.1.4.1.2636.3.7.1.2.1.7
Maximum round trip time allowed. If this threshold is crossed by any probe, a jnxPingRttThresholdExceeded trap will be sent.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..6000000  

jnxPingCtlRttStdDevThreshold 1.3.6.1.4.1.2636.3.7.1.2.1.8
The maximum round trip time standard deviation allowed over the course of any test. If the calculated standard deviation of the round trip time at the end of any test exceeds this threshold, a jnxPingRttStdDevThresholdExceeded trap will be sent.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..6000000  

jnxPingCtlRttJitterThreshold 1.3.6.1.4.1.2636.3.7.1.2.1.9
The maximum allowed jitter in the round trip time over the course of any test. Jitter is defined as the difference between the maximum and minimum round trip times measured over the course of a single test (jnxPingResultsMaxRttUs minus jnxPingResultsMinRttUs). If the measured jitter exceeds this threshold, a jnxPingRttJitterThresholdExceeded trap will be sent.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..6000000  

jnxPingCtlEgressTimeThreshold 1.3.6.1.4.1.2636.3.7.1.2.1.10
Maximum egress trip time allowed. If this threshold is crossed by any probe, a jnxPingEgressThresholdExceeded trap will be sent. This applies only if the probe type (pingCtlType) provides one way delay measurements. Currently jnxPingIcmpTimeStamp is the only supported probe type with this property.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..60000000  

jnxPingCtlEgressStdDevThreshold 1.3.6.1.4.1.2636.3.7.1.2.1.11
The maximum egress trip time standard deviation allowed over the course of any test. If the calculated standard deviation of the egress trip time at the end of any test exceeds this threshold, a jnxPingEgressStdDevThresholdExceeded trap will be sent. This applies only if the probe type (pingCtlType) provides one way delay measurements. Currently jnxPingIcmpTimeStamp is the only supported probe type with this property.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..60000000  

jnxPingCtlEgressJitterThreshold 1.3.6.1.4.1.2636.3.7.1.2.1.12
The maximum allowed jitter in the egress trip time over the course of any test. Jitter is defined as the difference between the maximum and minimum egress trip times measured over the course of a single test (jnxPingResultsMaxSrcDstt minus jnxPingResultsMinSrcDstt). If the measured jitter exceeds this threshold, a jnxPingEgressJitterThresholdExceeded trap will be sent. This applies only if the probe type (pingCtlType) provides one way delay measurements. Currently jnxPingIcmpTimeStamp is the only supported probe type with this property.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..60000000  

jnxPingCtlIngressTimeThreshold 1.3.6.1.4.1.2636.3.7.1.2.1.13
Maximum ingress trip time allowed. If this threshold is crossed by any probe, a jnxPingIngressThresholdExceeded trap will be sent. This applies only if the probe type (pingCtlType) provides one way delay measurements. Currently jnxPingIcmpTimeStamp is the only supported probe type with this property.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..60000000  

jnxPingCtlIngressStddevThreshold 1.3.6.1.4.1.2636.3.7.1.2.1.14
The maximum ingress trip time standard deviation allowed over the course of any test. If the calculated standard deviation of the ingress trip time at the end of any test exceeds this threshold, a jnxPingIngressStddevThresholdExceeded trap will be sent. This applies only if the probe type (pingCtlType) provides one way delay measurements. Currently jnxPingIcmpTimeStamp is the only supported probe type with this property.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..60000000  

jnxPingCtlIngressJitterThreshold 1.3.6.1.4.1.2636.3.7.1.2.1.15
The maximum allowed jitter in the ingress trip time over the course of any test. Jitter is defined as the difference between the maximum and minimum ingress trip times measured over the course of a single test (jnxPingResultsMaxDstSrct minus jnxPingResultsMinDstSrct). If the measured jitter exceeds this threshold, a jnxPingIngressJitterThresholdExceeded trap will be sent. This applies only if the probe type (pingCtlType) provides one way delay measurements. Currently jnxPingIcmpTimeStamp is the only supported probe type with this property.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..60000000  

jnxPingCtlTrapGeneration 1.3.6.1.4.1.2636.3.7.1.2.1.16
The value of this object determines when and if to generate a notification for this entry: rttThreshold(0) - Generate a jnxPingRttThresholdExceeded notification when the configured rtt threshold is exceeded. rttStdDevThreshold(1) - Generate a jnxPingRttStdDevThresholdExceeded notification when the configured rtt standard deviation threshold is exceeded. rttJitterThreshold(2) - Generate a jnxPingRttJitterThresholdExceeded notification when the configured rtt jitter threshold is exceeded. egressThreshold(3) - Generate a jnxPingEgressThresholdExceeded notification when the configured egress threshold is exceeded. This applies only if the probe type supports one way measurments. egressStdDevThreshold(4) - Generate a jnxPingEgressStdDevThresholdExceeded notification when the configured egress standard deviation threshold is exceeded. This applies only if the probe type supports one way measurments. egressJitterThreshold(5) - Generate a jnxPingEgressJitterThresholdExceeded notification when the configured egress jitter threshold is exceeded. This applies only if the probe type supports one way measurments. ingressThreshold(6) - Generate a jnxPingIngressThresholdExceeded notification when the configured ingress threshold is exceeded. This applies only if the probe type supports one way measurments. ingressStdDevThreshold(7) - Generate a jnxPingIngressStdDevThresholdExceeded notification when the configured ingress standard deviation threshold is exceeded. This applies only if the probe type supports one way measurments. ingressJitterThreshold(8) - Generate a jnxPingIngressJitterThresholdExceeded notification when the configured ingress jitter threshold is exceeded. This applies only if the probe type supports one way measurments. The value of this object defaults to zero, indicating that none of the above options have been selected.
Status: current Access: read-create
OBJECT-TYPE    
  BITS rttThreshold(0), rttStdDevThreshold(1), rttJitterThreshold(2), egressThreshold(3), egressStdDevThreshold(4), egressJitterThreshold(5), ingressThreshold(6), ingressStdDevThreshold(7), ingressJitterThreshold(8)  

jnxPingCtlTargetPort 1.3.6.1.4.1.2636.3.7.1.2.1.17
The target UDP/TCP port used by the probe. When ICMP ping is used, jnxPingCtlTargetPort value will be shown as 0.
Status: current Access: read-create
OBJECT-TYPE    
  InetPortNumber 7 | 49152..65535  

jnxPingCtlJseriesHWTimeStamp 1.3.6.1.4.1.2636.3.7.1.2.1.18
Use to enable the RPM Hardware Timestamp feature on J-series routers. For M/T series routers, use the jnxPingCtlIfName and pingCtlByPassRouteTable objects to redirect probes to the AS Pic. For those routers, this object must have the value: false.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

jnxPingCtlOneWayHWTimeStamp 1.3.6.1.4.1.2636.3.7.1.2.1.19
Use this object to enable Hardware Timestamp-based one-way measurements. If this object is not enabled (ie, set to true), no Hardware Timestamp based one way measurements or calculations will be performed for this control entry. This object applies to all Juniper routers. Note, due to clock synchronization artifacts, many one-way jitter measurements & calculations may include signifacant variations, in some cases orders of magnitude greater than the round trip times.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

jnxPingCtlMovAvgSize 1.3.6.1.4.1.2636.3.7.1.2.1.20
The Juniper RPM feature maintains a set of the most recent probe measurements & provides the same calculations over that collection as provided over a test (ie, average, standard deviation, etc). This data is available via the jnx-rpm mib or via the CLI/XML. The number of samples maintained in this moving collection is specified by this object. This value must be less than the number of samples maintained in the history table (ie, pingCtlMaxRows).
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

jnxPingCtlMXseriesHWTimeStamp 1.3.6.1.4.1.2636.3.7.1.2.1.21
Use to enable the RPM Hardware Timestamp feature on MX-series routers. For M/T series routers, use the jnxPingCtlIfName and pingCtlByPassRouteTable objects to redirect probes to the AS PIC. For those routers, this object must have the value: false.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

jnxPingCtlEXseriesHWTimeStamp 1.3.6.1.4.1.2636.3.7.1.2.1.22
Use to enable the RPM Hardware Timestamp feature on EX-series switches. For thoses, this object must have the value: false.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

jnxPingResultsTable 1.3.6.1.4.1.2636.3.7.1.3
Augments the pingResultsTable with additional data.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxPingResultsEntry

jnxPingResultsEntry 1.3.6.1.4.1.2636.3.7.1.3.1
Each entry provides additional ping test results.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxPingResultsEntry  

jnxPingResultsRttUs 1.3.6.1.4.1.2636.3.7.1.3.1.1
The round trip delays measured for the most recent successful probe during this test. Measured in microseconds.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingResultsSumRttUs 1.3.6.1.4.1.2636.3.7.1.3.1.2
The sum of the round trip delays measured for all the probes during this test. Measured in microseconds.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingResultsMinRttUs 1.3.6.1.4.1.2636.3.7.1.3.1.3
The minimum of the round trip delays measured for all the probes during this test. Measured in microseconds.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingResultsMaxRttUs 1.3.6.1.4.1.2636.3.7.1.3.1.4
The maximum of the round trip delays measured for all the probes during this test. Measured in microseconds.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingResultsAvgRttUs 1.3.6.1.4.1.2636.3.7.1.3.1.5
The average of the round trip delays measured for all the probes during this test. Measured in microseconds.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingResultsStdDevRttUs 1.3.6.1.4.1.2636.3.7.1.3.1.6
The standard deviation of the round trip delays measured during this test. Measured in microseconds.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingResultsEgressUs 1.3.6.1.4.1.2636.3.7.1.3.1.7
The egress trip delays measured for the most recent successful probe during this test. Measured in microseconds. This applies only if the probe type (pingCtlType) provides one-way delay measurements. For all other probe types, their values are irrelevant and will return 0.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingResultsMinEgressUs 1.3.6.1.4.1.2636.3.7.1.3.1.8
The minimum of the egress trip delays measured over all probes during this test. Measured in microseconds. This applies only if the probe type (pingCtlType) provides one-way delay measurements. For all other probe types, their values are irrelevant and will return 0.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingResultsMaxEgressUs 1.3.6.1.4.1.2636.3.7.1.3.1.9
The maximum of the egress trip delays measured over all probes during this test. Measured in microseconds. This applies only if the probe type (pingCtlType) provides one-way delay measurements. For all other probe types, their values are irrelevant and will return 0.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingResultsAvgEgressUs 1.3.6.1.4.1.2636.3.7.1.3.1.10
The average of the egress trip delays measured over all probes during this test. Measured in microseconds. This applies only if the probe type (pingCtlType) provides one-way delay measurements. For all other probe types, their values are irrelevant and will return 0.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingResultsStddevEgressUs 1.3.6.1.4.1.2636.3.7.1.3.1.11
The standard deviation of the egress trip delays measured over all probes during this test. Measured in microseconds. This applies only if the probe type (pingCtlType) provides one-way delay measurements. For all other probe types, their values are irrelevant and will return 0.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingResultsIngressUs 1.3.6.1.4.1.2636.3.7.1.3.1.12
The ingress trip delays measured for the most recent successful probe during this test. Measured in microseconds. This applies only if the probe type (pingCtlType) provides one-way delay measurements. For all other probe types, their values are irrelevant and will return 0.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingResultsMinIngressUs 1.3.6.1.4.1.2636.3.7.1.3.1.13
The minimum of the ingress trip delays measured for over all probes during this test. Measured in microseconds. This applies only if the probe type (pingCtlType) provides one-way delay measurements. For all other probe types, their values are irrelevant and will return 0.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingResultsMaxIngressUs 1.3.6.1.4.1.2636.3.7.1.3.1.14
The maximum of the ingress trip delays measured over all probes during this test. Measured in microseconds. This applies only if the probe type (pingCtlType) provides one-way delay measurements. For all other probe types, their values are irrelevant and will return 0.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingResultsAvgIngressUs 1.3.6.1.4.1.2636.3.7.1.3.1.15
The average of the ingress trip delays measured over all probes during this test. Measured in microseconds. This applies only if the probe type (pingCtlType) provides one-way delay measurements. For all other probe types, their values are irrelevant and will return 0.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingResultsStddevIngressUs 1.3.6.1.4.1.2636.3.7.1.3.1.16
The standard deviation of the ingress trip delays measured over all probes during this test. Measured in microseconds. This applies only if the probe type (pingCtlType) provides one-way delay measurements. For all other probe types, their values are irrelevant and will return 0.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingResultsJitterRttUs 1.3.6.1.4.1.2636.3.7.1.3.1.17
The jitter of the round trip delays measured for all the probes during this test. Measured in microseconds.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingResultsJitterEgressUs 1.3.6.1.4.1.2636.3.7.1.3.1.18
The jitter of the egress trip delays measured for all the probes during this test. Measured in microseconds. This applies only if the probe type (pingCtlType) provides one-way delay measurements. For all other probe types, their values are irrelevant and will return 0.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingResultsJitterIngressUs 1.3.6.1.4.1.2636.3.7.1.3.1.19
The jitter of the ingress trip delays measured for all the probes during this test. Measured in microseconds. This applies only if the probe type (pingCtlType) provides one-way delay measurements. For all other probe types, their values are irrelevant and will return 0.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingResultsStatus 1.3.6.1.4.1.2636.3.7.1.3.1.20
The result of the most recent probe.
Status: current Access: read-only
OBJECT-TYPE    
  OperationResponseStatus  

jnxPingResultsTime 1.3.6.1.4.1.2636.3.7.1.3.1.21
Timestamp for when the most recent probe result was determined.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

jnxPingResultsOwnerIndex 1.3.6.1.4.1.2636.3.7.1.3.1.22
This object has the same value as pingCtlOwnerIndex and is provided for those applications that are unable to parse the value of pingCtlOwnerIndex from the instance portion of the OIDs belonging to this table.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(0..32)  

jnxPingResultsTestName 1.3.6.1.4.1.2636.3.7.1.3.1.23
This object has the same value as pingCtlTestName and is provided for those applications that are unable to parse the value of pingCtlTestName from the instance portion of the OIDs belonging to this table.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(0..32)  

jnxPingProbeHistoryTable 1.3.6.1.4.1.2636.3.7.1.4
Augments the pingHistoryTable with additional data.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxPingProbeHistoryEntry

jnxPingProbeHistoryEntry 1.3.6.1.4.1.2636.3.7.1.4.1
Each entry provides additional ping history data.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxPingProbeHistoryEntry  

jnxPingProbeHistoryResponseUs 1.3.6.1.4.1.2636.3.7.1.4.1.1
The amount of time measured in microseconds from when a probe was sent to when its response was received or when it timed out. The value of this object is reported as 0 when it is not possible to transmit a probe.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingProbeHistoryJitterUs 1.3.6.1.4.1.2636.3.7.1.4.1.2
The time difference measured in microseconds between the maximum and minimum round trip times. Each history entry provides a running calculation of the jitter (calculated over the current test) at the time a probe was completed.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingProbeHistoryResponseEgressUs 1.3.6.1.4.1.2636.3.7.1.4.1.3
The amount of time measured in microseconds from when a probe was sent to when it was received by destination. This applies only if the probe type (pingCtlType) provides one way delay measurements. For all other probe types, the value is irrelevant and will return 0.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingProbeHistoryResponseIngressUs 1.3.6.1.4.1.2636.3.7.1.4.1.4
The amount of time measured in microseconds from when a probe was sent from the destination to when it was received. This applies only if the probe type (pingCtlType) provides one way delay measurements. For all other probe types, the value is irrelevant and will return 0.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingProbeHistoryEgressJitterUs 1.3.6.1.4.1.2636.3.7.1.4.1.5
The time difference measured in microseconds between the maximum and minimum egress trip times. Each history entry provides a running calculation of the jitter (calculated over the current test) at the time a probe was completed. This applies only if the probe type (pingCtlType) provides one way delay measurements. For all other probe types, the value is irrelevant and will return 0.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingProbeHistoryIngressJitterUs 1.3.6.1.4.1.2636.3.7.1.4.1.6
The time difference measured in microseconds between the maximum and minimum ingress trip times. Each history entry provides a running calculation of the jitter (calculated over the current test) at the time a probe was completed. This applies only if the probe type (pingCtlType) provides one way delay measurements. For all other probe types, the value is irrelevant and will return 0.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingLastTestResultTable 1.3.6.1.4.1.2636.3.7.1.5
Stores result of the most recently completed test. Entry corresponding to a test will be created only after completion of first test.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxPingLastTestResultEntry

jnxPingLastTestResultEntry 1.3.6.1.4.1.2636.3.7.1.5.1
Each entry provides most recently completed test result.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxPingLastTestResultEntry  

jnxPingLastTestResultProbeResponses 1.3.6.1.4.1.2636.3.7.1.5.1.1
Number of responses received in the most recently completed test.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingLastTestResultSentProbes 1.3.6.1.4.1.2636.3.7.1.5.1.2
The value of this object reflects the number of probes sent in the most recently completed test.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingLastTestResultSumRttUs 1.3.6.1.4.1.2636.3.7.1.5.1.3
The sum of the round trip delays measured for all the probes during the most recently completed test. Measured in microseconds.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingLastTestResultMinRttUs 1.3.6.1.4.1.2636.3.7.1.5.1.4
The minimum of the round trip delays measured for all the probes during the most recently completed test. Measured in microseconds.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingLastTestResultMaxRttUs 1.3.6.1.4.1.2636.3.7.1.5.1.5
The maximum of the round trip delays measured for all the probes during the most recently completed test. Measured in microseconds.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingLastTestResultAvgRttUs 1.3.6.1.4.1.2636.3.7.1.5.1.6
The average of the round trip delays measured for all the probes during the most recently completed test. Measured in microseconds.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingLastTestResultStdDevRttUs 1.3.6.1.4.1.2636.3.7.1.5.1.7
The standard deviation of the round trip delays measured during the most recently completed test. Measured in microseconds.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingLastTestResultMinEgressUs 1.3.6.1.4.1.2636.3.7.1.5.1.8
The minimum of the egress trip delays measured over all probes during the most recently completed test. Measured in microseconds. This applies only if the probe type (pingCtlType) provides one-way delay measurements. For all other probe types, their values are irrelevant and will return 0.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingLastTestResultMaxEgressUs 1.3.6.1.4.1.2636.3.7.1.5.1.9
The maximum of the egress trip delays measured over all probes during the most recently completed test. Measured in microseconds. This applies only if the probe type (pingCtlType) provides one-way delay measurements. For all other probe types, their values are irrelevant and will return 0.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingLastTestResultAvgEgressUs 1.3.6.1.4.1.2636.3.7.1.5.1.10
The average of the egress trip delays measured over all probes during the most recently completed test. Measured in microseconds. This applies only if the probe type (pingCtlType) provides one-way delay measurements. For all other probe types, their values are irrelevant and will return 0.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingLastTestResultStddevEgressUs 1.3.6.1.4.1.2636.3.7.1.5.1.11
The standard deviation of the egress trip delays measured over all probes during the most recently completed test. Measured in microseconds. This applies only if the probe type (pingCtlType) provides one-way delay measurements. For all other probe types, their values are irrelevant and will return 0.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingLastTestResultMinIngressUs 1.3.6.1.4.1.2636.3.7.1.5.1.12
The minimum of the ingress trip delays measured for over all probes during the most recently completed test. Measured in microseconds. This applies only if the probe type (pingCtlType) provides one-way delay measurements. For all other probe types, their values are irrelevant and will return 0.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingLastTestResultMaxIngressUs 1.3.6.1.4.1.2636.3.7.1.5.1.13
The maximum of the ingress trip delays measured over all probes during the most recently completed test. Measured in microseconds. This applies only if the probe type (pingCtlType) provides one-way delay measurements. For all other probe types, their values are irrelevant and will return 0.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingLastTestResultAvgIngressUs 1.3.6.1.4.1.2636.3.7.1.5.1.14
The average of the ingress trip delays measured over all probes during the most recently completed test. Measured in microseconds. This applies only if the probe type (pingCtlType) provides one-way delay measurements. For all other probe types, their values are irrelevant and will return 0.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingLastTestResultStddevIngressUs 1.3.6.1.4.1.2636.3.7.1.5.1.15
The standard deviation of the ingress trip delays measured over all probes during the most recently completed test. Measured in microseconds. This applies only if the probe type (pingCtlType) provides one-way delay measurements. For all other probe types, their values are irrelevant and will return 0.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingLastTestResultPeakToPeakJitterRttUs 1.3.6.1.4.1.2636.3.7.1.5.1.16
This indicates the difference between the min and max delays over the course of the last completed test. Measured in microseconds.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingLastTestResultPeakToPeakJitterEgressUs 1.3.6.1.4.1.2636.3.7.1.5.1.17
This indicates the difference between the min and max egress trip delays over the course of the last completed test. Measured in microseconds. This applies only if the probe type (pingCtlType) provides one-way delay measurements. For all other probe types, their values are irrelevant and will return 0.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingLastTestResultPeakToPeakJitterIngressUs 1.3.6.1.4.1.2636.3.7.1.5.1.18
This indicates the difference between the min and max ingress trip delays over the course of the last completed test. Measured in microseconds. This applies only if the probe type (pingCtlType) provides one-way delay measurements. For all other probe types, their values are irrelevant and will return 0.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxPingLastTestResultTime 1.3.6.1.4.1.2636.3.7.1.5.1.19
Timestamp for when the last test was completed.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

jnxPingNotificationPrefix 1.3.6.1.4.1.2636.4.9.0
All Juniper-specific ping notifications are registered under this branch.
Status: current Access: read-only
OBJECT-IDENTITY    

jnxPingRttThresholdExceeded 1.3.6.1.4.1.2636.4.9.0.1
This notification is generated when the round trip time (jnxPingCtlRttThreshold) exceeds the configured threshold (jnxPingCtlRttThreshold) and the rttThreshold bit is set in jnxPingCtlTrapGeneration.
Status: current Access: read-only
NOTIFICATION-TYPE    

jnxPingRttStdDevThresholdExceeded 1.3.6.1.4.1.2636.4.9.0.2
This notification is generated when the standard deviation of the round trip time (jnxPingResultsStdDevRttUs) exceeds the configured threshold (jnxPingCtlRttStdDevThreshold) and the rttStdDevThreshold bit is set in jnxPingCtlTrapGeneration.
Status: current Access: read-only
NOTIFICATION-TYPE    

jnxPingRttJitterThresholdExceeded 1.3.6.1.4.1.2636.4.9.0.3
This notification is generated when the round trip time jitter (jnxPingResultsMaxRttUs minus jnxPingResultsMinRttUs) exceeds the configured threshold (jnxPingCtlRttJitterThreshold) and the rttJitterThreshold bit is set in jnxPingCtlTrapGeneration.
Status: current Access: read-only
NOTIFICATION-TYPE    

jnxPingEgressThresholdExceeded 1.3.6.1.4.1.2636.4.9.0.4
This notification is generated when the egress time (jnxPingResultsEgressUs) exceeds the configured threshold (jnxPingCtlEgressTimeThreshold) and the egressThreshold bit is set in jnxPingCtlTrapGeneration.
Status: current Access: read-only
NOTIFICATION-TYPE    

jnxPingEgressStdDevThresholdExceeded 1.3.6.1.4.1.2636.4.9.0.5
This notification is generated when the standard deviation of the egress time (jnxPingResultsStddevEgressUs) exceeds the configured threshold (jnxPingCtlEgressStdDevThreshold) and the egressStdDevThreshold bit is set in jnxPingCtlTrapGeneration.
Status: current Access: read-only
NOTIFICATION-TYPE    

jnxPingEgressJitterThresholdExceeded 1.3.6.1.4.1.2636.4.9.0.6
This notification is generated when the egress time jitter (jnxPingResultsMaxEgressUs minus jnxPingResultsMinEgressUs) exceeds the configured threshold (jnxPingCtlEgressJitterThreshold) and the egressJitterThreshold bit is set in jnxPingCtlTrapGeneration.
Status: current Access: read-only
NOTIFICATION-TYPE    

jnxPingIngressThresholdExceeded 1.3.6.1.4.1.2636.4.9.0.7
This notification is generated when the ingress time (jnxPingResultsIngressUs) exceeds the configured threshold (jnxPingCtlIngressTimeThreshold) and the ingressThreshold bit is set in jnxPingCtlTrapGeneration.
Status: current Access: read-only
NOTIFICATION-TYPE    

jnxPingIngressStddevThresholdExceeded 1.3.6.1.4.1.2636.4.9.0.8
This notification is generated when the standard deviation of the ingress time (jnxPingResultsStddevIngressUs) exceeds the configured threshold (jnxPingCtlIngressStddevThreshold) and the ingressStdDevThreshold bit is set in jnxPingCtlTrapGeneration.
Status: current Access: read-only
NOTIFICATION-TYPE    

jnxPingIngressJitterThresholdExceeded 1.3.6.1.4.1.2636.4.9.0.9
This notification is generated when the ingress time jitter (jnxPingResultsMaxIngressUs minus jnxPingResultsMinIngressUs) exceeds the configured threshold (jnxPingCtlIngressJitterThreshold) and the ingressJitterThreshold bit is set in jnxPingCtlTrapGeneration.
Status: current Access: read-only
NOTIFICATION-TYPE