JUNIPER-IFOTN-MIB

File: JUNIPER-IFOTN-MIB.mib (88949 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC JUNIPER-SMI
IF-MIB JNX-OPT-IF-EXT-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE TimeTicks
NOTIFICATION-TYPE Unsigned32 Counter32
Integer32 DisplayString DateAndTime
TEXTUAL-CONVENTION RowStatus TruthValue
jnxIfOtnMibRoot jnxIfOtnNotifications ifIndex
ifDescr JnxoptIfOTNOChAlarms JnxoptIfOTNODUkTcmAlarms

Defined Types

JnxIfAdminStates  
Admin states for an interface
TEXTUAL-CONVENTION    
  INTEGER jnxAdminStateInService(1), jnxAdminStateInServiceMA(2), jnxAdminStateOutofService(3), jnxAdminStateOutofServiceMA(4)  

JnxIfOperStates  
Operational states for an interface
TEXTUAL-CONVENTION    
  INTEGER jnxOperStateInit(1), jnxOperStateNormal(2), jnxOperStateFault(3), jnxOperStateDegraded(4)  

JnxIfOtnRate  
Rates for an interface
TEXTUAL-CONVENTION    
  INTEGER otu0(1), otu1(2), otu2(3), otu2e(4), otu3(5), otu4(6), otu1e(7), otu5(8)  

JnxIfOtnFecType  
fec modes of an interface
TEXTUAL-CONVENTION    
  INTEGER nofec(0), gfec(1), efecI2(2), efecI3(3), efecI4(4), efecI5(5), efecI6(6), efecI7(7), efecI8(8), efecI9(9), gfecandsdfec(10), sdfec(11), hgfec(12)  

JnxIfOtnLayer  
Layer which describes the table
TEXTUAL-CONVENTION    
  INTEGER jnxOch(1), jnxOTUk(2), jnxODUk(3), jnxTCM(4)  

JnxIfOtnType  
Near End or Far End
TEXTUAL-CONVENTION    
  INTEGER jnxNearEnd(1), jnxFarEnd(2)  

JnxIfOtnDirection  
Direction for the entities in the table
TEXTUAL-CONVENTION    
  INTEGER jnxTxDir(1), jnxRxDir(2), jnxBiDir(3)  

JnxIfOtnSeverity  
Severity of the Notification
TEXTUAL-CONVENTION    
  INTEGER jnxCritical(1), jnxMajor(2), jnxMinor(3), jnxInfo(4)  

JnxIfOtnServiceStateAction  
Notification's action on the service state
TEXTUAL-CONVENTION    
  INTEGER jnxNotSupported(0), jnxNonServiceAffecting(1), jnxServiceAffecting(2)  

JnxIfOtnOChCfgEntry  
SEQUENCE    
  jnxIfOtnOChCfgContainerIndex Integer32
  jnxIfOtnOChCfgL1Index Integer32
  jnxIfOtnOChCfgL2Index Integer32
  jnxIfOtnOChCfgL3Index Integer32
  jnxIfOtnLocalLoopback TruthValue
  jnxIfOtnLineLoopback TruthValue
  jnxIfOtnPayloadLoopback TruthValue
  jnxIfOtnAdminState JnxIfAdminStates
  jnxIfOtnOperState JnxIfOperStates
  jnxIfOtnIndex Unsigned32
  jnxIfOtnOChStatus BITS
  jnxIfOtnOChPortMode Unsigned32

JnxIfOtnOTUkCfgEntry  
SEQUENCE    
  jnxIfOtnOTUkCfgContainerIndex Integer32
  jnxIfOtnOTUkCfgL1Index Integer32
  jnxIfOtnOTUkCfgL2Index Integer32
  jnxIfOtnOTUkCfgL3Index Integer32
  jnxIfOtnOTUkCfgRate JnxIfOtnRate
  jnxIfOtnOTUkCfgFecMode JnxIfOtnFecType
  jnxIfOtnOTUkEnableAutoFrrByteInsert TruthValue
  jnxIfOtnOTUkEnableBERFrrSupport TruthValue
  jnxIfOtnOTUkPreFecBERThresholdMantissa Integer32
  jnxIfOtnOTUkPreFecBERThresholdExponent Integer32
  jnxIfOtnOTUkPreFecBERThresholdTime Integer32
  jnxIfOtnOTUkTIMActEnabled TruthValue
  jnxIfOtnOTUkTxTTI OCTET STRING
  jnxIfOtnOTUkRxTTI OCTET STRING
  jnxIfOtnOTUkExpectedRxSapi OCTET STRING
  jnxIfOtnOTUkExpectedRxDapi OCTET STRING
  jnxIfOtnOTUkStatus BITS
  jnxIfOtnOTUkPreFecBERThresholdClearMantissa Integer32
  jnxIfOtnOTUkPreFecBERThresholdClearExponent Integer32
  jnxIfOtnOTUkTxSapiTTIFstByteNul TruthValue
  jnxIfOtnOTUkTxDapiTTIFstByteNul TruthValue
  jnxIfOtnOTUkExpectedRxSapiFstByteNul TruthValue
  jnxIfOtnOTUkExpectedRxDapiFstByteNul TruthValue

JnxIfOtnODUkCfgEntry  
SEQUENCE    
  jnxIfOtnODUkCfgContainerIndex Integer32
  jnxIfOtnODUkCfgL1Index Integer32
  jnxIfOtnODUkCfgL2Index Integer32
  jnxIfOtnODUkCfgL3Index Integer32
  jnxIfOtnODUkAPSPCC0 Integer32
  jnxIfOtnODUkAPSPCC1 Integer32
  jnxIfOtnODUkAPSPCC2 Integer32
  jnxIfOtnODUkAPSPCC3 Integer32
  jnxIfOtnODUkPayloadType Integer32
  jnxIfOtnODUkTIMActEnabled TruthValue
  jnxIfOtnODUkTxTTI OCTET STRING
  jnxIfOtnODUkRxTTI OCTET STRING
  jnxIfOtnODUkExpectedRxSapi OCTET STRING
  jnxIfOtnODUkExpectedRxDapi OCTET STRING
  jnxIfOtnODUkStatus BITS
  jnxIfOtnODUkRxPayloadType Integer32
  jnxIfOtnODUkTxSapiTTIFstByteNul TruthValue
  jnxIfOtnODUkTxDapiTTIFstByteNul TruthValue
  jnxIfOtnODUkExpectedRxSapiFstByteNul TruthValue
  jnxIfOtnODUkExpectedRxDapiFstByteNul TruthValue

JnxIfOtnTcmCfgEntry  
SEQUENCE    
  jnxIfOtnTcmCfgContainerIndex Integer32
  jnxIfOtnTcmCfgL1Index Integer32
  jnxIfOtnTcmCfgL2Index Integer32
  jnxIfOtnTcmCfgL3Index Integer32
  jnxIfOtnTcmCfgLevel Integer32
  jnxIfOtnTCMEnable TruthValue
  jnxIfOtnTcmTxTTI OCTET STRING
  jnxIfOtnTcmRxTTI OCTET STRING
  jnxIfOtnTcmExpectedRxSapi OCTET STRING
  jnxIfOtnTcmExpectedRxDapi OCTET STRING
  jnxIfOtnTcmStatus BITS

JnxIfOtnODUkTcmTestEntry  
SEQUENCE    
  jnxIfOtnODUkTcmTestLayer JnxIfOtnLayer
  jnxIfOtnODUkTcmTestTCMLevel Integer32
  jnxIfOtnODUkTcmInsertAis TruthValue
  jnxIfOtnODUkTcmInsertLck TruthValue
  jnxIfOtnODUkTcmInsertOci TruthValue
  jnxIfOtnODUkPayloadPRBS TruthValue
  jnxIfOtnODUkPayloadPRBSResult OCTET STRING

JnxIfOtnODUkTcmDMEntry  
SEQUENCE    
  jnxIfOtnODUkTcmDMLayer Integer32
  jnxIfOtnODUkTcmDMLevel Integer32
  jnxIfOtnDMConnectionMonitoringEndpoint TruthValue
  jnxIfOtnDMBypass TruthValue
  jnxIfOtnDMPersistFrames Integer32
  jnxIfOtnDMEnable TruthValue

JnxIfOtnNotificationTrigEntry  
SEQUENCE    
  jnxIfOtnNotificationTrigContainerIndex Integer32
  jnxIfOtnNotificationTrigL1Index Integer32
  jnxIfOtnNotificationTrigL2Index Integer32
  jnxIfOtnNotificationTrigL3Index Integer32
  jnxIfOtnNotificationTrigLayer JnxIfOtnLayer
  jnxIfOtnNotificationTrigTCMLevel Integer32
  jnxIfOtnNotificationTrigAlmId Integer32
  jnxIfOtnNotificationTrigSeverity JnxIfOtnSeverity
  jnxIfOtnNotificationTrigIgnore TruthValue
  jnxIfOtnNotificationTrigHoldtimeUp Integer32
  jnxIfOtnNotificationTrigHoldtimeDown Integer32
  jnxIfOtnTrigServiceStateAction JnxIfOtnServiceStateAction

JnxOtnClearIfPMsEntry  
SEQUENCE    
  jnxOtnClearCurrent TruthValue
  jnxOtnClearInterfaceInterval TruthValue
  jnxOtnClearInterfaceDay TruthValue
  jnxOtnClearInterfaceAll TruthValue

JnxIfOtnOCh2CfgEntry  
SEQUENCE    
  jnxIfOtnOCh2CfgContainerIndex Integer32
  jnxIfOtnOCh2CfgL1Index Integer32
  jnxIfOtnOCh2CfgL2Index Integer32
  jnxIfOtnOCh2CfgL3Index Integer32
  jnxIfOtnOCh2CfgL4Index Integer32
  jnxIfOtnOCh2LocalLoopback TruthValue
  jnxIfOtnOCh2LineLoopback TruthValue
  jnxIfOtnOCh2PayloadLoopback TruthValue
  jnxIfOtnOCh2AdminState JnxIfAdminStates
  jnxIfOtnOCh2OperState JnxIfOperStates
  jnxIfOtnOCh2Index Unsigned32
  jnxIfOtnOCh2Status BITS
  jnxIfOtnOCh2PortMode Unsigned32

JnxIfOtnOCh2OTUkCfgEntry  
SEQUENCE    
  jnxIfOtnOCh2OTUkCfgContIndx Integer32
  jnxIfOtnOCh2OTUkCfgL1Index Integer32
  jnxIfOtnOCh2OTUkCfgL2Index Integer32
  jnxIfOtnOCh2OTUkCfgL3Index Integer32
  jnxIfOtnOCh2OTUkCfgL4Index Integer32
  jnxIfOtnOCh2OTUkCfgRate JnxIfOtnRate
  jnxIfOtnOCh2OTUkCfgFecMode JnxIfOtnFecType
  jnxIfOtnOCh2OTUkEnAutoFrrByteIns TruthValue
  jnxIfOtnOCh2OTUkEnBERFrrSupport TruthValue
  jnxIfOtnOCh2OTUkPreFecBERThMant Integer32
  jnxIfOtnOCh2OTUkPreFecBERThExpo Integer32
  jnxIfOtnOCh2OTUkPreFecBERThTime Integer32
  jnxIfOtnOCh2OTUkTIMActEnabled TruthValue
  jnxIfOtnOCh2OTUkTxTTI OCTET STRING
  jnxIfOtnOCh2OTUkRxTTI OCTET STRING
  jnxIfOtnOCh2OTUkExpectedRxSapi OCTET STRING
  jnxIfOtnOCh2OTUkExpectedRxDapi OCTET STRING
  jnxIfOtnOCh2OTUkStatus BITS
  jnxIfOtnOCh2OTUkPreFecBERThClrMn Integer32
  jnxIfOtnOCh2OTUkPreFecBERThClrEx Integer32

JnxIfOtnOCh2ODUkCfgEntry  
SEQUENCE    
  jnxIfOtnOCh2ODUkCfgContIndx Integer32
  jnxIfOtnOCh2ODUkCfgL1Index Integer32
  jnxIfOtnOCh2ODUkCfgL2Index Integer32
  jnxIfOtnOCh2ODUkCfgL3Index Integer32
  jnxIfOtnOCh2ODUkCfgL4Index Integer32
  jnxIfOtnOCh2ODUkAPSPCC0 Integer32
  jnxIfOtnOCh2ODUkAPSPCC1 Integer32
  jnxIfOtnOCh2ODUkAPSPCC2 Integer32
  jnxIfOtnOCh2ODUkAPSPCC3 Integer32
  jnxIfOtnOCh2ODUkPayloadType Integer32
  jnxIfOtnOCh2ODUkTIMActEnabled TruthValue
  jnxIfOtnOCh2ODUkTxTTI OCTET STRING
  jnxIfOtnOCh2ODUkRxTTI OCTET STRING
  jnxIfOtnOCh2ODUkExpectedRxSapi OCTET STRING
  jnxIfOtnOCh2ODUkExpectedRxDapi OCTET STRING
  jnxIfOtnOCh2ODUkStatus BITS
  jnxIfOtnOCh2ODUkRxPayloadType Integer32

JnxIfOtnOCh2TcmCfgEntry  
SEQUENCE    
  jnxIfOtnOCh2TcmCfgContIndx Integer32
  jnxIfOtnOCh2TcmCfgL1Index Integer32
  jnxIfOtnOCh2TcmCfgL2Index Integer32
  jnxIfOtnOCh2TcmCfgL3Index Integer32
  jnxIfOtnOCh2TcmCfgL4Index Integer32
  jnxIfOtnOCh2TcmCfgLevel Integer32
  jnxIfOtnOCh2TCMEnable TruthValue
  jnxIfOtnOCh2TcmTxTTI OCTET STRING
  jnxIfOtnOCh2TcmRxTTI OCTET STRING
  jnxIfOtnOCh2TcmExpectedRxSapi OCTET STRING
  jnxIfOtnOCh2TcmExpectedRxDapi OCTET STRING
  jnxIfOtnOCh2TcmStatus BITS

Defined Values

jnxIfOtnMib 1.3.6.1.4.1.2636.3.70.1
Deprecated OCh2 tables and entries
MODULE-IDENTITY    

jnxIfOtn 1.3.6.1.4.1.2636.3.70.1.1
OBJECT IDENTIFIER    

jnxIfOtnOCh2 1.3.6.1.4.1.2636.3.70.1.2
OBJECT IDENTIFIER    

jnxIfOtnOChCfgTable 1.3.6.1.4.1.2636.3.70.1.1.1
Information about the Otn OCh Config Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxIfOtnOChCfgEntry

jnxIfOtnOChCfgEntry 1.3.6.1.4.1.2636.3.70.1.1.1.1
A conceptual row that contains of the Otn OCh Config Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxIfOtnOChCfgEntry  

jnxIfOtnOChCfgContainerIndex 1.3.6.1.4.1.2636.3.70.1.1.1.1.1
The associated jnxContentsContainerIndex - eg shelf..
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..1024  

jnxIfOtnOChCfgL1Index 1.3.6.1.4.1.2636.3.70.1.1.1.1.2
The level one index associated with this subject ... eg fpc slot.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..1024  

jnxIfOtnOChCfgL2Index 1.3.6.1.4.1.2636.3.70.1.1.1.1.3
The level two index associated with this subject .. eg pic slot.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..1024  

jnxIfOtnOChCfgL3Index 1.3.6.1.4.1.2636.3.70.1.1.1.1.4
The level three index associated with this subject.. eg port.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..1024  

jnxIfOtnLocalLoopback 1.3.6.1.4.1.2636.3.70.1.1.1.1.5
This is the local loopback at the Line (after the optics).
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxIfOtnLineLoopback 1.3.6.1.4.1.2636.3.70.1.1.1.1.6
This is the line loopback at the Line.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxIfOtnPayloadLoopback 1.3.6.1.4.1.2636.3.70.1.1.1.1.7
This is the Payload loopback before the optics.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxIfOtnAdminState 1.3.6.1.4.1.2636.3.70.1.1.1.1.8
The Admin state of this interface
Status: current Access: read-write
OBJECT-TYPE    
  JnxIfAdminStates  

jnxIfOtnOperState 1.3.6.1.4.1.2636.3.70.1.1.1.1.9
The operational state of this interface
Status: current Access: read-only
OBJECT-TYPE    
  JnxIfOperStates  

jnxIfOtnIndex 1.3.6.1.4.1.2636.3.70.1.1.1.1.10
The interface ifIndex of this interface
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxIfOtnOChStatus 1.3.6.1.4.1.2636.3.70.1.1.1.1.11
The interface status at the OCh layer.
Status: current Access: read-only
OBJECT-TYPE    
  BITS los(0), lof(1), lom(2), wavelengthlockerr(3)  

jnxIfOtnOChPortMode 1.3.6.1.4.1.2636.3.70.1.1.1.1.12
The Port Mode for this interface 0 - default (not applicable) 1 - lan 2 - wan 3 - gfp
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxIfOtnOTUkCfgTable 1.3.6.1.4.1.2636.3.70.1.1.2
Information about the Otn OTUk config table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxIfOtnOTUkCfgEntry

jnxIfOtnOTUkCfgEntry 1.3.6.1.4.1.2636.3.70.1.1.2.1
A conceptual row that contains the Otn OTUk config table.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxIfOtnOTUkCfgEntry  

jnxIfOtnOTUkCfgContainerIndex 1.3.6.1.4.1.2636.3.70.1.1.2.1.1
The associated jnxContentsContainerIndex - eg shelf.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..1024  

jnxIfOtnOTUkCfgL1Index 1.3.6.1.4.1.2636.3.70.1.1.2.1.2
The level one index associated with this subject ... eg fpc slot.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..1024  

jnxIfOtnOTUkCfgL2Index 1.3.6.1.4.1.2636.3.70.1.1.2.1.3
The level two index associated with this subject .. eg pic slot.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..1024  

jnxIfOtnOTUkCfgL3Index 1.3.6.1.4.1.2636.3.70.1.1.2.1.4
The level three index associated with this subject.. eg port.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..1024  

jnxIfOtnOTUkCfgRate 1.3.6.1.4.1.2636.3.70.1.1.2.1.5
This is the rate for the interface and the rates depend on the interface/fru type.
Status: current Access: read-write
OBJECT-TYPE    
  JnxIfOtnRate  

jnxIfOtnOTUkCfgFecMode 1.3.6.1.4.1.2636.3.70.1.1.2.1.6
This is the Fec type in the OTU frame and the selection depends on the interface/fru type.
Status: current Access: read-write
OBJECT-TYPE    
  JnxIfOtnFecType  

jnxIfOtnOTUkEnableAutoFrrByteInsert 1.3.6.1.4.1.2636.3.70.1.1.2.1.7
This will enable/disable the automatic insertion of the frr SF/SD byte in the overhead bytes(RES)
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxIfOtnOTUkEnableBERFrrSupport 1.3.6.1.4.1.2636.3.70.1.1.2.1.8
This will enable/disable the FRR support for BER
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxIfOtnOTUkPreFecBERThresholdMantissa 1.3.6.1.4.1.2636.3.70.1.1.2.1.9
This will set the BER threshold(mantissa), which when crossed will trigger Signal Degrade.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

jnxIfOtnOTUkPreFecBERThresholdExponent 1.3.6.1.4.1.2636.3.70.1.1.2.1.10
This will set the BER threshold(exponent), which when crossed will trigger Signal Degrade.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

jnxIfOtnOTUkPreFecBERThresholdTime 1.3.6.1.4.1.2636.3.70.1.1.2.1.11
The collection times (1ms - 1sec) to calculate the BER.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

jnxIfOtnOTUkTIMActEnabled 1.3.6.1.4.1.2636.3.70.1.1.2.1.12
Indicates whether the Trace Identifier Mismatch (TIM) Consequent Action function is enabled. The default value of this object is false(2).
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxIfOtnOTUkTxTTI 1.3.6.1.4.1.2636.3.70.1.1.2.1.13
The Trace TTI SAPI 0..15, DAPI 16..31 32 ..63 user defined
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..64)  

jnxIfOtnOTUkRxTTI 1.3.6.1.4.1.2636.3.70.1.1.2.1.14
The Receive Trace TTI SAPI 0..15, DAPI 16..31 32 ..63 user defined
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(64)  

jnxIfOtnOTUkExpectedRxSapi 1.3.6.1.4.1.2636.3.70.1.1.2.1.15
Expected receive SAPI.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

jnxIfOtnOTUkExpectedRxDapi 1.3.6.1.4.1.2636.3.70.1.1.2.1.16
Expected receive DAPI.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

jnxIfOtnOTUkStatus 1.3.6.1.4.1.2636.3.70.1.1.2.1.17
The interface status at the OTUk layer.
Status: current Access: read-only
OBJECT-TYPE    
  BITS ais(0), bdi(1), iae(2), ttim(3), sf(4), sd(5), biae(6), tsf(7), ssf(8), fecexcessive(9), fecdegrade(10), fefecerr(11)  

jnxIfOtnOTUkPreFecBERThresholdClearMantissa 1.3.6.1.4.1.2636.3.70.1.1.2.1.18
This will set the BER threshold(mantissa) for clear signal degrade condition, which signal degrade condition will be cleared when Pre-Fec error count is below the clear threshold error count.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

jnxIfOtnOTUkPreFecBERThresholdClearExponent 1.3.6.1.4.1.2636.3.70.1.1.2.1.19
This will set the BER threshold(exponent) for clear signal degrade condition, which signal degrade condition will be cleared when Pre-Fec error count is below the clear threshold error count.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

jnxIfOtnOTUkTxSapiTTIFstByteNul 1.3.6.1.4.1.2636.3.70.1.1.2.1.20
This will fill the first byte of TTI with all zero as per the G.709 recommendation.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxIfOtnOTUkTxDapiTTIFstByteNul 1.3.6.1.4.1.2636.3.70.1.1.2.1.21
This will fill the first byte of TTI with all zero as per the G.709 recommendation.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxIfOtnOTUkExpectedRxSapiFstByteNul 1.3.6.1.4.1.2636.3.70.1.1.2.1.22
This will fill the first byte of TTI with all zero as per the G.709 recommendation.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxIfOtnOTUkExpectedRxDapiFstByteNul 1.3.6.1.4.1.2636.3.70.1.1.2.1.23
This will fill the first byte of TTI with all zero as per the G.709 recommendation.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxIfOtnODUkCfgTable 1.3.6.1.4.1.2636.3.70.1.1.3
Information about the Otn ODUk config table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxIfOtnODUkCfgEntry

jnxIfOtnODUkCfgEntry 1.3.6.1.4.1.2636.3.70.1.1.3.1
A conceptual row that contains information about the Otn ODUk config.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxIfOtnODUkCfgEntry  

jnxIfOtnODUkCfgContainerIndex 1.3.6.1.4.1.2636.3.70.1.1.3.1.1
The associated jnxContentsContainerIndex - eg shelf..
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..1024  

jnxIfOtnODUkCfgL1Index 1.3.6.1.4.1.2636.3.70.1.1.3.1.2
The level one index associated with this subject ... eg fpc slot.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..1024  

jnxIfOtnODUkCfgL2Index 1.3.6.1.4.1.2636.3.70.1.1.3.1.3
The level two index associated with this subject .. eg pic slot.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..1024  

jnxIfOtnODUkCfgL3Index 1.3.6.1.4.1.2636.3.70.1.1.3.1.4
The level three index associated with this subject.. eg port.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..1024  

jnxIfOtnODUkAPSPCC0 1.3.6.1.4.1.2636.3.70.1.1.3.1.5
Read/Write APS PCC byte 0 for this ODUk only.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..255  

jnxIfOtnODUkAPSPCC1 1.3.6.1.4.1.2636.3.70.1.1.3.1.6
Read/Write APS PCC byte 1 for this ODUk only.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..255  

jnxIfOtnODUkAPSPCC2 1.3.6.1.4.1.2636.3.70.1.1.3.1.7
Read/Write APS PCC byte 2 for this ODUk only.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..255  

jnxIfOtnODUkAPSPCC3 1.3.6.1.4.1.2636.3.70.1.1.3.1.8
Read/Write APS PCC byte 3 for this ODUk only.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..255  

jnxIfOtnODUkPayloadType 1.3.6.1.4.1.2636.3.70.1.1.3.1.9
Read/Write Payload Type for ODUk only.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..255  

jnxIfOtnODUkTIMActEnabled 1.3.6.1.4.1.2636.3.70.1.1.3.1.10
Indicates whether the Trace Identifier Mismatch (TIM) Consequent Action function is enabled. The default value of this object is false(2).
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxIfOtnODUkTxTTI 1.3.6.1.4.1.2636.3.70.1.1.3.1.11
The Trace TTI SAPI 0..15, DAPI 16..31 32 ..63 user defined for this layer.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..64)  

jnxIfOtnODUkRxTTI 1.3.6.1.4.1.2636.3.70.1.1.3.1.12
The Receive Trace TTI SAPI 0..15, DAPI 16..31 32 ..63 user defined for this layer.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(64)  

jnxIfOtnODUkExpectedRxSapi 1.3.6.1.4.1.2636.3.70.1.1.3.1.13
Expected receive SAPI for this layer.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

jnxIfOtnODUkExpectedRxDapi 1.3.6.1.4.1.2636.3.70.1.1.3.1.14
Expected receive DAPI for this layer.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

jnxIfOtnODUkStatus 1.3.6.1.4.1.2636.3.70.1.1.3.1.15
The status at the ODUk layer Only some of these alarms are valid for the TCM layer
Status: current Access: read-only
OBJECT-TYPE    
  BITS ais(0), bdi(1), iae(2), ttim(3), sf(4), sd(5), biae(6), tsf(7), ssf(8), csf(9), oci(10), lck(11), ltc(12), ptm(13)  

jnxIfOtnODUkRxPayloadType 1.3.6.1.4.1.2636.3.70.1.1.3.1.16
Receive Payload Type for ODUk only.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

jnxIfOtnODUkTxSapiTTIFstByteNul 1.3.6.1.4.1.2636.3.70.1.1.3.1.17
This will fill the first byte of TTI with all zero as per the G.709 recommendation.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxIfOtnODUkTxDapiTTIFstByteNul 1.3.6.1.4.1.2636.3.70.1.1.3.1.18
This will fill the first byte of TTI with all zero as per the G.709 recommendation.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxIfOtnODUkExpectedRxSapiFstByteNul 1.3.6.1.4.1.2636.3.70.1.1.3.1.19
This will fill the first byte of TTI with all zero as per the G.709 recommendation.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxIfOtnODUkExpectedRxDapiFstByteNul 1.3.6.1.4.1.2636.3.70.1.1.3.1.20
This will fill the first byte of TTI with all zero as per the G.709 recommendation.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxIfOtnTcmCfgTable 1.3.6.1.4.1.2636.3.70.1.1.4
Information about the Otn TCM config table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxIfOtnTcmCfgEntry

jnxIfOtnTcmCfgEntry 1.3.6.1.4.1.2636.3.70.1.1.4.1
A conceptual row that contains information about the Otn Tcm config.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxIfOtnTcmCfgEntry  

jnxIfOtnTcmCfgContainerIndex 1.3.6.1.4.1.2636.3.70.1.1.4.1.1
The associated jnxContentsContainerIndex - eg shelf.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..1024  

jnxIfOtnTcmCfgL1Index 1.3.6.1.4.1.2636.3.70.1.1.4.1.2
The level one index associated with this subject ... eg fpc slot.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..1024  

jnxIfOtnTcmCfgL2Index 1.3.6.1.4.1.2636.3.70.1.1.4.1.3
The level two index associated with this subject .. eg pic slot.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..1024  

jnxIfOtnTcmCfgL3Index 1.3.6.1.4.1.2636.3.70.1.1.4.1.4
The level three index associated with this subject.. eg port.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..1024  

jnxIfOtnTcmCfgLevel 1.3.6.1.4.1.2636.3.70.1.1.4.1.5
The TCM level for the Table
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..6  

jnxIfOtnTCMEnable 1.3.6.1.4.1.2636.3.70.1.1.4.1.6
Enable this TCM layer (only for TCM layers)
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxIfOtnTcmTxTTI 1.3.6.1.4.1.2636.3.70.1.1.4.1.7
The Trace TTI SAPI 0..15, DAPI 16..31 32 ..63 user defined for this layer.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..64)  

jnxIfOtnTcmRxTTI 1.3.6.1.4.1.2636.3.70.1.1.4.1.8
The Receive Trace TTI SAPI 0..15, DAPI 16..31 32 ..63 user defined for this layer.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(64)  

jnxIfOtnTcmExpectedRxSapi 1.3.6.1.4.1.2636.3.70.1.1.4.1.9
Expected receive SAPI for this layer.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

jnxIfOtnTcmExpectedRxDapi 1.3.6.1.4.1.2636.3.70.1.1.4.1.10
Expected receive DAPI for this layer.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

jnxIfOtnTcmStatus 1.3.6.1.4.1.2636.3.70.1.1.4.1.11
The status at the TCM layer.
Status: current Access: read-only
OBJECT-TYPE    
  BITS ais(0), bdi(1), iae(2), ttim(3), biae(6), tsf(7), ssf(8), ltc(9)  

jnxIfOtnODUkTcmTestTable 1.3.6.1.4.1.2636.3.70.1.1.5
Information about the Otn ODUk Test function table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxIfOtnODUkTcmTestEntry

jnxIfOtnODUkTcmTestEntry 1.3.6.1.4.1.2636.3.70.1.1.5.1
A conceptual row that contains information about the Otn ODUk Test function.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxIfOtnODUkTcmTestEntry  

jnxIfOtnODUkTcmTestLayer 1.3.6.1.4.1.2636.3.70.1.1.5.1.1
The layer OTU/ODU/TCM layer for the alarm
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxIfOtnLayer  

jnxIfOtnODUkTcmTestTCMLevel 1.3.6.1.4.1.2636.3.70.1.1.5.1.2
For ODUk will be this will be 0 If layer is TCM then this will give the TCM level 1..6.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..6  

jnxIfOtnODUkTcmInsertAis 1.3.6.1.4.1.2636.3.70.1.1.5.1.3
Insert ODU Ais into OTN stream.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxIfOtnODUkTcmInsertLck 1.3.6.1.4.1.2636.3.70.1.1.5.1.4
Insert ODU Lck into OTN stream.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxIfOtnODUkTcmInsertOci 1.3.6.1.4.1.2636.3.70.1.1.5.1.5
Insert ODU Oci into OTN stream.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxIfOtnODUkPayloadPRBS 1.3.6.1.4.1.2636.3.70.1.1.5.1.6
Insert Payload PRBS, For ODUK layer and TCM level is 0.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxIfOtnODUkPayloadPRBSResult 1.3.6.1.4.1.2636.3.70.1.1.5.1.7
Result of the Payload PRBS .
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

jnxIfOtnODUkTcmDMTable 1.3.6.1.4.1.2636.3.70.1.1.6
Table for Otn ODUk/TCM Delay Measurement config table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxIfOtnODUkTcmDMEntry

jnxIfOtnODUkTcmDMEntry 1.3.6.1.4.1.2636.3.70.1.1.6.1
A conceptual row that contains information about the Delay Measurement test table.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxIfOtnODUkTcmDMEntry  

jnxIfOtnODUkTcmDMLayer 1.3.6.1.4.1.2636.3.70.1.1.6.1.1
The layer OTU/ODU/TCM layer for the alarm
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxIfOtnLayer  

jnxIfOtnODUkTcmDMLevel 1.3.6.1.4.1.2636.3.70.1.1.6.1.2
For ODUk will be this will be 0 If layer is TCM then this will give the TCM level 1..6.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..6  

jnxIfOtnDMConnectionMonitoringEndpoint 1.3.6.1.4.1.2636.3.70.1.1.6.1.3
Originate Connection Monitoring Endpoint for the Delay Measurement
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxIfOtnDMBypass 1.3.6.1.4.1.2636.3.70.1.1.6.1.4
Act as tandem, passing Dm value through node
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxIfOtnDMPersistFrames 1.3.6.1.4.1.2636.3.70.1.1.6.1.5
Number of consequtive frames required to declare Dm Complete
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

jnxIfOtnDMEnable 1.3.6.1.4.1.2636.3.70.1.1.6.1.6
Start/Stop the DM measurement
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxIfOtnDMRemoteLoopEnable 1.3.6.1.4.1.2636.3.70.1.1.6.1.7
Remote Loop Enable/Disable
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxIfOtnNotificationTrigDefaultHoldtimeUp 1.3.6.1.4.1.2636.3.70.1.1.7
This object will indicate the time (ms) for the defect to persist before it is declared an alarm.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

jnxIfOtnNotificationTrigDefaultHoldtimeDown 1.3.6.1.4.1.2636.3.70.1.1.8
This object will indicate the time (ms) for the defect to absent before the alarm is cleared.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

jnxIfOtnNotificationTrigTable 1.3.6.1.4.1.2636.3.70.1.1.9
Information about the otn Alarm/Alart/Info trigger table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxIfOtnNotificationTrigEntry

jnxIfOtnNotificationTrigEntry 1.3.6.1.4.1.2636.3.70.1.1.9.1
A conceptual row that contains information about the Otn Alarm Trigger Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxIfOtnNotificationTrigEntry  

jnxIfOtnNotificationTrigContainerIndex 1.3.6.1.4.1.2636.3.70.1.1.9.1.1
The associated jnxContentsContainerIndex - eg shelf.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..1024  

jnxIfOtnNotificationTrigL1Index 1.3.6.1.4.1.2636.3.70.1.1.9.1.2
The level one index associated with this subject ... eg fpc slot.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..1024  

jnxIfOtnNotificationTrigL2Index 1.3.6.1.4.1.2636.3.70.1.1.9.1.3
The level two index associated with this subject .. eg pic slot.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..1024  

jnxIfOtnNotificationTrigL3Index 1.3.6.1.4.1.2636.3.70.1.1.9.1.4
The level three index associated with this subject.. eg port.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..1024  

jnxIfOtnNotificationTrigLayer 1.3.6.1.4.1.2636.3.70.1.1.9.1.5
The layer OTU/ODU/TCM layer for the alarm
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxIfOtnLayer  

jnxIfOtnNotificationTrigTCMLevel 1.3.6.1.4.1.2636.3.70.1.1.9.1.6
For OCh/OTUk/ODUk will be this will be 0 If layer is TCM then this will give the TCM level 1..6.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..6  

jnxIfOtnNotificationTrigAlmId 1.3.6.1.4.1.2636.3.70.1.1.9.1.7
This will be the ID of Alarm for that layer 'JnxoptIfOTNOChAlarms'/'JnxoptIfOTNODUkTcmAlarms'.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..255  

jnxIfOtnNotificationTrigSeverity 1.3.6.1.4.1.2636.3.70.1.1.9.1.8
This will be the Severity of the Notification for that layer.
Status: current Access: read-write
OBJECT-TYPE    
  JnxIfOtnSeverity  

jnxIfOtnNotificationTrigIgnore 1.3.6.1.4.1.2636.3.70.1.1.9.1.9
This object will ignore the alarm when set.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxIfOtnNotificationTrigHoldtimeUp 1.3.6.1.4.1.2636.3.70.1.1.9.1.10
This object will indicate the time (ms) for the defect to persist before it is declared an alarm.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

jnxIfOtnNotificationTrigHoldtimeDown 1.3.6.1.4.1.2636.3.70.1.1.9.1.11
This object will indicate the time (ms) for the defect is absent before the alarm is cleared.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

jnxIfOtnTrigServiceStateAction 1.3.6.1.4.1.2636.3.70.1.1.9.1.12
This will indicate whether this alarm is service affecting or not .
Status: current Access: read-only
OBJECT-TYPE    
  JnxIfOtnServiceStateAction  

jnxOtnClearAllPMs 1.3.6.1.4.1.2636.3.70.1.1.10
To clear all Performance monitoring counters on OTN interfaces
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxOtnClearInterfacePMs 1.3.6.1.4.1.2636.3.70.1.1.11
To clear all Performance monitoring counters on this OTN interfaces
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxOtnClearInterfaceCurrentPM 1.3.6.1.4.1.2636.3.70.1.1.12
To clear the current Performance monitoring counters on this OTN interfaces
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxOtnClearIfPMsTable 1.3.6.1.4.1.2636.3.70.1.1.13
To clear OTN Performance monitoring counters on this OTN interfaces
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxOtnClearIfPMsEntry

jnxOtnClearIfPMsEntry 1.3.6.1.4.1.2636.3.70.1.1.13.1
A conceptual row that s used to clear the OTN PM Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxOtnClearIfPMsEntry  

jnxOtnClearCurrent 1.3.6.1.4.1.2636.3.70.1.1.13.1.1
1- to clear all the current OTN PM's for this interface
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxOtnClearInterfaceInterval 1.3.6.1.4.1.2636.3.70.1.1.13.1.2
1- to clear all the OTN PM's intervals(1-96) for this interface
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxOtnClearInterfaceDay 1.3.6.1.4.1.2636.3.70.1.1.13.1.3
1 - to clear all the Current Day and Previous Day OTN PM's for this interface
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxOtnClearInterfaceAll 1.3.6.1.4.1.2636.3.70.1.1.13.1.4
1 - to clear all the OTN PM's for this interface
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxIfOtnOCh2CfgTable 1.3.6.1.4.1.2636.3.70.1.2.1
Table was for 48x10G/12x40G gingerALE PIC in 10G mode. It is not supported hence marked as obsolete. Information about the Otn OCh2 Config Table.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxIfOtnOCh2CfgEntry

jnxIfOtnOCh2CfgEntry 1.3.6.1.4.1.2636.3.70.1.2.1.1
A conceptual row that contains of the Otn OCh2 Config Table.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  JnxIfOtnOCh2CfgEntry  

jnxIfOtnOCh2CfgContainerIndex 1.3.6.1.4.1.2636.3.70.1.2.1.1.1
Container Index associated with the object instance.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Integer32 1..1024  

jnxIfOtnOCh2CfgL1Index 1.3.6.1.4.1.2636.3.70.1.2.1.1.2
FPC slot number of the interface.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Integer32 1..1024  

jnxIfOtnOCh2CfgL2Index 1.3.6.1.4.1.2636.3.70.1.2.1.1.3
PIC slot number of the interface.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Integer32 1..1024  

jnxIfOtnOCh2CfgL3Index 1.3.6.1.4.1.2636.3.70.1.2.1.1.4
Port number of the interface.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Integer32 1..1024  

jnxIfOtnOCh2CfgL4Index 1.3.6.1.4.1.2636.3.70.1.2.1.1.5
Sub-Port number of the interface.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Integer32 1..1024  

jnxIfOtnOCh2LocalLoopback 1.3.6.1.4.1.2636.3.70.1.2.1.1.6
This is the local loopback at the Line (after the optics).
Status: obsolete Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxIfOtnOCh2LineLoopback 1.3.6.1.4.1.2636.3.70.1.2.1.1.7
This is the line loopback at the Line.
Status: obsolete Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxIfOtnOCh2PayloadLoopback 1.3.6.1.4.1.2636.3.70.1.2.1.1.8
This is the Payload loopback before the optics.
Status: obsolete Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxIfOtnOCh2AdminState 1.3.6.1.4.1.2636.3.70.1.2.1.1.9
The Admin state of this interface
Status: obsolete Access: read-write
OBJECT-TYPE    
  JnxIfAdminStates  

jnxIfOtnOCh2OperState 1.3.6.1.4.1.2636.3.70.1.2.1.1.10
The operational state of this interface
Status: obsolete Access: read-only
OBJECT-TYPE    
  JnxIfOperStates  

jnxIfOtnOCh2Index 1.3.6.1.4.1.2636.3.70.1.2.1.1.11
The interface ifIndex of this interface
Status: obsolete Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxIfOtnOCh2Status 1.3.6.1.4.1.2636.3.70.1.2.1.1.12
The interface status at the OCh layer.
Status: current Access: read-only
OBJECT-TYPE    
  BITS los(0), lof(1), lom(2), wavelengthlockerr(3)  

jnxIfOtnOCh2PortMode 1.3.6.1.4.1.2636.3.70.1.2.1.1.13
The Port Mode for this interface 0 - default (not applicable) 1 - lan 2 - wan 3 - gfp
Status: obsolete Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxIfOtnOCh2OTUkCfgTable 1.3.6.1.4.1.2636.3.70.1.2.2
Table was for 48x10G/12x40G gingerALE PIC in 10G mode. It is not supported hence marked as obsolete. Information about the Otn OCh2 OTUk config table.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxIfOtnOCh2OTUkCfgEntry

jnxIfOtnOCh2OTUkCfgEntry 1.3.6.1.4.1.2636.3.70.1.2.2.1
A conceptual row that contains the Otn OCh2 OTUk config table.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  JnxIfOtnOCh2OTUkCfgEntry  

jnxIfOtnOCh2OTUkCfgContIndx 1.3.6.1.4.1.2636.3.70.1.2.2.1.1
Container Index associated with the object instance.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Integer32 1..1024  

jnxIfOtnOCh2OTUkCfgL1Index 1.3.6.1.4.1.2636.3.70.1.2.2.1.2
FPC slot number of the interface.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Integer32 1..1024  

jnxIfOtnOCh2OTUkCfgL2Index 1.3.6.1.4.1.2636.3.70.1.2.2.1.3
PIC slot number of the interface.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Integer32 1..1024  

jnxIfOtnOCh2OTUkCfgL3Index 1.3.6.1.4.1.2636.3.70.1.2.2.1.4
Port number of the interface.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Integer32 1..1024  

jnxIfOtnOCh2OTUkCfgL4Index 1.3.6.1.4.1.2636.3.70.1.2.2.1.5
Port number of the interface.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Integer32 1..1024  

jnxIfOtnOCh2OTUkCfgRate 1.3.6.1.4.1.2636.3.70.1.2.2.1.6
This is the rate for the interface and the rates depend on the interface/fru type.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JnxIfOtnRate  

jnxIfOtnOCh2OTUkCfgFecMode 1.3.6.1.4.1.2636.3.70.1.2.2.1.7
This is the Fec type in the OTU frame and the selection depends on the interface/fru type.
Status: obsolete Access: read-write
OBJECT-TYPE    
  JnxIfOtnFecType  

jnxIfOtnOCh2OTUkEnAutoFrrByteIns 1.3.6.1.4.1.2636.3.70.1.2.2.1.8
This will enable/disable the automatic insertion of the frr SF/SD byte in the overhead bytes(RES)
Status: obsolete Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxIfOtnOCh2OTUkEnBERFrrSupport 1.3.6.1.4.1.2636.3.70.1.2.2.1.9
This will enable/disable the FRR support for BER
Status: obsolete Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxIfOtnOCh2OTUkPreFecBERThMant 1.3.6.1.4.1.2636.3.70.1.2.2.1.10
This will set the BER threshold(mantissa), which when crossed will trigger Signal Degrade.
Status: obsolete Access: read-write
OBJECT-TYPE    
  Integer32  

jnxIfOtnOCh2OTUkPreFecBERThExpo 1.3.6.1.4.1.2636.3.70.1.2.2.1.11
This will set the BER threshold(exponent), which when crossed will trigger Signal Degrade.
Status: obsolete Access: read-write
OBJECT-TYPE    
  Integer32  

jnxIfOtnOCh2OTUkPreFecBERThTime 1.3.6.1.4.1.2636.3.70.1.2.2.1.12
The collection times (1ms - 1sec) to calculate the BER.
Status: obsolete Access: read-write
OBJECT-TYPE    
  Integer32  

jnxIfOtnOCh2OTUkTIMActEnabled 1.3.6.1.4.1.2636.3.70.1.2.2.1.13
Indicates whether the Trace Identifier Mismatch (TIM) Consequent Action function is enabled. The default value of this object is false(2).
Status: obsolete Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxIfOtnOCh2OTUkTxTTI 1.3.6.1.4.1.2636.3.70.1.2.2.1.14
The Trace TTI SAPI 0..15, DAPI 16..31 32 ..63 user defined
Status: obsolete Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..64)  

jnxIfOtnOCh2OTUkRxTTI 1.3.6.1.4.1.2636.3.70.1.2.2.1.15
The Receive Trace TTI SAPI 0..15, DAPI 16..31 32 ..63 user defined
Status: obsolete Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(64)  

jnxIfOtnOCh2OTUkExpectedRxSapi 1.3.6.1.4.1.2636.3.70.1.2.2.1.16
Expected receive SAPI.
Status: obsolete Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

jnxIfOtnOCh2OTUkExpectedRxDapi 1.3.6.1.4.1.2636.3.70.1.2.2.1.17
Expected receive DAPI.
Status: obsolete Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

jnxIfOtnOCh2OTUkStatus 1.3.6.1.4.1.2636.3.70.1.2.2.1.18
The interface status at the OTUk layer.
Status: obsolete Access: read-only
OBJECT-TYPE    
  BITS ais(0), bdi(1), iae(2), ttim(3), sf(4), sd(5), biae(6), tsf(7), ssf(8), fecexcessive(9), fecdegrade(10)  

jnxIfOtnOCh2OTUkPreFecBERThClrMn 1.3.6.1.4.1.2636.3.70.1.2.2.1.19
This will set the BER threshold(mantissa) for clear signal degrade condition, which signal degrade condition will be cleared when Pre-Fec error count is below the clear threshold error count.
Status: obsolete Access: read-write
OBJECT-TYPE    
  Integer32  

jnxIfOtnOCh2OTUkPreFecBERThClrEx 1.3.6.1.4.1.2636.3.70.1.2.2.1.20
This will set the BER threshold(exponent) for clear signal degrade condition, which signal degrade condition will be cleared when Pre-Fec error count is below the clear threshold error count.
Status: obsolete Access: read-write
OBJECT-TYPE    
  Integer32  

jnxIfOtnOCh2ODUkCfgTable 1.3.6.1.4.1.2636.3.70.1.2.3
Table was for 48x10G/12x40G gingerALE PIC in 10G mode. It is not supported hence marked as obsolete. Information about the Otn ODUk config table.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxIfOtnOCh2ODUkCfgEntry

jnxIfOtnOCh2ODUkCfgEntry 1.3.6.1.4.1.2636.3.70.1.2.3.1
A conceptual row that contains information about the Otn ODUk config.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  JnxIfOtnOCh2ODUkCfgEntry  

jnxIfOtnOCh2ODUkCfgContIndx 1.3.6.1.4.1.2636.3.70.1.2.3.1.1
Container Index associated with the Object Instance.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Integer32 0..255  

jnxIfOtnOCh2ODUkCfgL1Index 1.3.6.1.4.1.2636.3.70.1.2.3.1.2
FPC slot number of the interface.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Integer32 0..255  

jnxIfOtnOCh2ODUkCfgL2Index 1.3.6.1.4.1.2636.3.70.1.2.3.1.3
PIC slot number of the interface.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Integer32 0..255  

jnxIfOtnOCh2ODUkCfgL3Index 1.3.6.1.4.1.2636.3.70.1.2.3.1.4
Port number of the interface.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Integer32 0..255  

jnxIfOtnOCh2ODUkCfgL4Index 1.3.6.1.4.1.2636.3.70.1.2.3.1.5
Sub-Port number of the interface.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Integer32 0..255  

jnxIfOtnOCh2ODUkAPSPCC0 1.3.6.1.4.1.2636.3.70.1.2.3.1.6
Read/Write APS PCC byte 0 for this ODUk only.
Status: obsolete Access: read-write
OBJECT-TYPE    
  Integer32 0..255  

jnxIfOtnOCh2ODUkAPSPCC1 1.3.6.1.4.1.2636.3.70.1.2.3.1.7
Read/Write APS PCC byte 1 for this ODUk only.
Status: obsolete Access: read-write
OBJECT-TYPE    
  Integer32 0..255  

jnxIfOtnOCh2ODUkAPSPCC2 1.3.6.1.4.1.2636.3.70.1.2.3.1.8
Read/Write APS PCC byte 2 for this ODUk only.
Status: obsolete Access: read-write
OBJECT-TYPE    
  Integer32 0..255  

jnxIfOtnOCh2ODUkAPSPCC3 1.3.6.1.4.1.2636.3.70.1.2.3.1.9
Read/Write APS PCC byte 3 for this ODUk only.
Status: obsolete Access: read-write
OBJECT-TYPE    
  Integer32 0..255  

jnxIfOtnOCh2ODUkPayloadType 1.3.6.1.4.1.2636.3.70.1.2.3.1.10
Read/Write Payload Type for ODUk only.
Status: obsolete Access: read-write
OBJECT-TYPE    
  Integer32 0..255  

jnxIfOtnOCh2ODUkTIMActEnabled 1.3.6.1.4.1.2636.3.70.1.2.3.1.11
Indicates whether the Trace Identifier Mismatch (TIM) Consequent Action function is enabled. The default value of this object is false(2).
Status: obsolete Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxIfOtnOCh2ODUkTxTTI 1.3.6.1.4.1.2636.3.70.1.2.3.1.12
The Trace TTI SAPI 0..15, DAPI 16..31 32 ..63 user defined for this layer.
Status: obsolete Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..64)  

jnxIfOtnOCh2ODUkRxTTI 1.3.6.1.4.1.2636.3.70.1.2.3.1.13
The Receive Trace TTI SAPI 0..15, DAPI 16..31 32 ..63 user defined for this layer.
Status: obsolete Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(64)  

jnxIfOtnOCh2ODUkExpectedRxSapi 1.3.6.1.4.1.2636.3.70.1.2.3.1.14
Expected receive SAPI for this layer.
Status: obsolete Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

jnxIfOtnOCh2ODUkExpectedRxDapi 1.3.6.1.4.1.2636.3.70.1.2.3.1.15
Expected receive DAPI for this layer.
Status: obsolete Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

jnxIfOtnOCh2ODUkStatus 1.3.6.1.4.1.2636.3.70.1.2.3.1.16
The status at the ODUk layer Only some of these alarms are valid for the TCM layer
Status: current Access: read-only
OBJECT-TYPE    
  BITS ais(0), bdi(1), iae(2), ttim(3), sf(4), sd(5), biae(6), tsf(7), ssf(8), csf(9), oci(10), lck(11), ltc(12), ptm(13)  

jnxIfOtnOCh2ODUkRxPayloadType 1.3.6.1.4.1.2636.3.70.1.2.3.1.17
Receive Payload Type for ODUk only.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

jnxIfOtnOCh2TcmCfgTable 1.3.6.1.4.1.2636.3.70.1.2.4
Table was for 48x10G/12x40G gingerALE PIC in 10G mode. It is not supported hence marked as obsolete. Information about the Otn TCM config table.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxIfOtnOCh2TcmCfgEntry

jnxIfOtnOCh2TcmCfgEntry 1.3.6.1.4.1.2636.3.70.1.2.4.1
A conceptual row that contains information about the Otn Tcm config.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  JnxIfOtnOCh2TcmCfgEntry  

jnxIfOtnOCh2TcmCfgContIndx 1.3.6.1.4.1.2636.3.70.1.2.4.1.1
Container Index associated with the object.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Integer32 0..255  

jnxIfOtnOCh2TcmCfgL1Index 1.3.6.1.4.1.2636.3.70.1.2.4.1.2
FPC slot number of the interface.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Integer32 0..255  

jnxIfOtnOCh2TcmCfgL2Index 1.3.6.1.4.1.2636.3.70.1.2.4.1.3
PIC slot number of the interface.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Integer32 0..255  

jnxIfOtnOCh2TcmCfgL3Index 1.3.6.1.4.1.2636.3.70.1.2.4.1.4
Port number of the interface.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Integer32 0..255  

jnxIfOtnOCh2TcmCfgL4Index 1.3.6.1.4.1.2636.3.70.1.2.4.1.5
Sub-Port number of the interface.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Integer32 0..255  

jnxIfOtnOCh2TcmCfgLevel 1.3.6.1.4.1.2636.3.70.1.2.4.1.6
The TCM level for the Table
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Integer32 1..6  

jnxIfOtnOCh2TCMEnable 1.3.6.1.4.1.2636.3.70.1.2.4.1.7
Enable this TCM layer (only for TCM layers)
Status: obsolete Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxIfOtnOCh2TcmTxTTI 1.3.6.1.4.1.2636.3.70.1.2.4.1.8
The Trace TTI SAPI 0..15, DAPI 16..31 32 ..63 user defined for this layer.
Status: obsolete Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..64)  

jnxIfOtnOCh2TcmRxTTI 1.3.6.1.4.1.2636.3.70.1.2.4.1.9
The Receive Trace TTI SAPI 0..15, DAPI 16..31 32 ..63 user defined for this layer.
Status: obsolete Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(64)  

jnxIfOtnOCh2TcmExpectedRxSapi 1.3.6.1.4.1.2636.3.70.1.2.4.1.10
Expected receive SAPI for this layer.
Status: obsolete Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

jnxIfOtnOCh2TcmExpectedRxDapi 1.3.6.1.4.1.2636.3.70.1.2.4.1.11
Expected receive DAPI for this layer.
Status: obsolete Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

jnxIfOtnOCh2TcmStatus 1.3.6.1.4.1.2636.3.70.1.2.4.1.12
The status at the TCM layer.
Status: obsolete Access: read-only
OBJECT-TYPE    
  BITS ais(0), bdi(1), iae(2), ttim(3), biae(6), tsf(7), ssf(8), ltc(9)  

jnxIfOtnNotificationPrefix 1.3.6.1.4.1.2636.4.21.0
OBJECT IDENTIFIER    

jnxIfOtnNotificationAdminStatus 1.3.6.1.4.1.2636.4.21.0.1
Notification of the admin state of the otn interface.
Status: current Access: read-only
NOTIFICATION-TYPE    

jnxIfOtnNotificationOperStatus 1.3.6.1.4.1.2636.4.21.0.2
Notification of operational state of the otn interface
Status: current Access: read-only
NOTIFICATION-TYPE    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor