JNX-OPT-IF-MIB

File: JNX-OPT-IF-MIB.mib (243308 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMP-FRAMEWORK-MIB
SNMPv2-CONF JUNIPER-SMI IF-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Gauge32
Integer32 Unsigned32 transmission
TEXTUAL-CONVENTION RowPointer RowStatus
TruthValue SnmpAdminString MODULE-COMPLIANCE
OBJECT-GROUP jnxoptIfMibRoot ifIndex

Defined Types

JnxoptIfAcTI  
The trace identifier (TI) accepted at the receiver.
TEXTUAL-CONVENTION    
  OCTET STRING Size(64)  

JnxoptIfBitRateK  
Indicates the index that is used to represent a supported bit rate and the different versions of OPUk, ODUk and OTUk. Allowed values of k are defined in ITU-T G.709. Currently allowed values in G.709 are: k=1 represents an approximate bit rate of 2.5 Gbit/s, k=2 represents an approximate bit rate of 10 Gbit/s, k=3 represents an approximate bit rate of 40 Gbit/s.
TEXTUAL-CONVENTION    
  Integer32  

JnxoptIfDEGM  
Indicates the threshold level for declaring a Degraded Signal defect (dDEG). A dDEG shall be declared if JnxoptIfDEGM consecutive bad PM Seconds are detected.
TEXTUAL-CONVENTION    
  Unsigned32 2..10  

JnxoptIfDEGThr  
Indicates the threshold level for declaring a performance monitoring (PM) Second to be bad. A PM Second is declared bad if the percentage of detected errored blocks in that second is greater than or equal to JnxoptIfDEGThr.
TEXTUAL-CONVENTION    
  Unsigned32 1..100  

JnxoptIfDirectionality  
Indicates the directionality of an entity.
TEXTUAL-CONVENTION    
  INTEGER sink(1), source(2), bidirectional(3)  

JnxoptIfSinkOrSource  
Indicates the directionality of an entity that is allowed only to be a source or sink.
TEXTUAL-CONVENTION    
  INTEGER sink(1), source(2)  

JnxoptIfExDAPI  
The Destination Access Point Identifier (DAPI) expected by the receiver.
TEXTUAL-CONVENTION    
  OCTET STRING Size(16)  

JnxoptIfExSAPI  
The Source Access Point Identifier (SAPI) expected by the receiver.
TEXTUAL-CONVENTION    
  OCTET STRING Size(16)  

JnxoptIfIntervalNumber  
Uniquely identifies a 15-minute interval. The interval identified by 1 is the most recently completed interval, and the interval identified by n is the interval immediately preceding the one identified by n-1.
TEXTUAL-CONVENTION    
  Unsigned32 1..96  

JnxoptIfTIMDetMode  
Indicates the mode of the Trace Identifier Mismatch (TIM) Detection function.
TEXTUAL-CONVENTION    
  INTEGER off(1), dapi(2), sapi(3), both(4)  

JnxoptIfTxTI  
The trace identifier (TI) transmitted.
TEXTUAL-CONVENTION    
  OCTET STRING Size(64)  

JnxoptIfOTMnEntry  
SEQUENCE    
  jnxoptIfOTMnOrder Unsigned32
  jnxoptIfOTMnReduced TruthValue
  jnxoptIfOTMnBitRates BITS
  jnxoptIfOTMnInterfaceType SnmpAdminString
  jnxoptIfOTMnTcmMax Unsigned32
  jnxoptIfOTMnOpticalReach INTEGER

JnxoptIfPerfMonIntervalEntry  
SEQUENCE    
  jnxoptIfPerfMonCurrentTimeElapsed Gauge32
  jnxoptIfPerfMonCurDayTimeElapsed Gauge32
  jnxoptIfPerfMonIntervalNumIntervals Unsigned32
  jnxoptIfPerfMonIntervalNumInvalidIntervals Unsigned32

JnxoptIfOTSnConfigEntry  
SEQUENCE    
  jnxoptIfOTSnDirectionality JnxoptIfDirectionality
  jnxoptIfOTSnAprStatus SnmpAdminString
  jnxoptIfOTSnAprControl SnmpAdminString
  jnxoptIfOTSnTraceIdentifierTransmitted JnxoptIfTxTI
  jnxoptIfOTSnDAPIExpected JnxoptIfExDAPI
  jnxoptIfOTSnSAPIExpected JnxoptIfExSAPI
  jnxoptIfOTSnTraceIdentifierAccepted JnxoptIfAcTI
  jnxoptIfOTSnTIMDetMode JnxoptIfTIMDetMode
  jnxoptIfOTSnTIMActEnabled TruthValue
  jnxoptIfOTSnCurrentStatus BITS

JnxoptIfOTSnSinkCurrentEntry  
SEQUENCE    
  jnxoptIfOTSnSinkCurrentSuspectedFlag TruthValue
  jnxoptIfOTSnSinkCurrentInputPower Integer32
  jnxoptIfOTSnSinkCurrentLowInputPower Integer32
  jnxoptIfOTSnSinkCurrentHighInputPower Integer32
  jnxoptIfOTSnSinkCurrentLowerInputPowerThreshold Integer32
  jnxoptIfOTSnSinkCurrentUpperInputPowerThreshold Integer32
  jnxoptIfOTSnSinkCurrentOutputPower Integer32
  jnxoptIfOTSnSinkCurrentLowOutputPower Integer32
  jnxoptIfOTSnSinkCurrentHighOutputPower Integer32
  jnxoptIfOTSnSinkCurrentLowerOutputPowerThreshold Integer32
  jnxoptIfOTSnSinkCurrentUpperOutputPowerThreshold Integer32

JnxoptIfOTSnSinkIntervalEntry  
SEQUENCE    
  jnxoptIfOTSnSinkIntervalNumber JnxoptIfIntervalNumber
  jnxoptIfOTSnSinkIntervalSuspectedFlag TruthValue
  jnxoptIfOTSnSinkIntervalLastInputPower Integer32
  jnxoptIfOTSnSinkIntervalLowInputPower Integer32
  jnxoptIfOTSnSinkIntervalHighInputPower Integer32
  jnxoptIfOTSnSinkIntervalLastOutputPower Integer32
  jnxoptIfOTSnSinkIntervalLowOutputPower Integer32
  jnxoptIfOTSnSinkIntervalHighOutputPower Integer32

JnxoptIfOTSnSinkCurDayEntry  
SEQUENCE    
  jnxoptIfOTSnSinkCurDaySuspectedFlag TruthValue
  jnxoptIfOTSnSinkCurDayLowInputPower Integer32
  jnxoptIfOTSnSinkCurDayHighInputPower Integer32
  jnxoptIfOTSnSinkCurDayLowOutputPower Integer32
  jnxoptIfOTSnSinkCurDayHighOutputPower Integer32

JnxoptIfOTSnSinkPrevDayEntry  
SEQUENCE    
  jnxoptIfOTSnSinkPrevDaySuspectedFlag TruthValue
  jnxoptIfOTSnSinkPrevDayLastInputPower Integer32
  jnxoptIfOTSnSinkPrevDayLowInputPower Integer32
  jnxoptIfOTSnSinkPrevDayHighInputPower Integer32
  jnxoptIfOTSnSinkPrevDayLastOutputPower Integer32
  jnxoptIfOTSnSinkPrevDayLowOutputPower Integer32
  jnxoptIfOTSnSinkPrevDayHighOutputPower Integer32

JnxoptIfOTSnSrcCurrentEntry  
SEQUENCE    
  jnxoptIfOTSnSrcCurrentSuspectedFlag TruthValue
  jnxoptIfOTSnSrcCurrentOutputPower Integer32
  jnxoptIfOTSnSrcCurrentLowOutputPower Integer32
  jnxoptIfOTSnSrcCurrentHighOutputPower Integer32
  jnxoptIfOTSnSrcCurrentLowerOutputPowerThreshold Integer32
  jnxoptIfOTSnSrcCurrentUpperOutputPowerThreshold Integer32
  jnxoptIfOTSnSrcCurrentInputPower Integer32
  jnxoptIfOTSnSrcCurrentLowInputPower Integer32
  jnxoptIfOTSnSrcCurrentHighInputPower Integer32
  jnxoptIfOTSnSrcCurrentLowerInputPowerThreshold Integer32
  jnxoptIfOTSnSrcCurrentUpperInputPowerThreshold Integer32

JnxoptIfOTSnSrcIntervalEntry  
SEQUENCE    
  jnxoptIfOTSnSrcIntervalNumber JnxoptIfIntervalNumber
  jnxoptIfOTSnSrcIntervalSuspectedFlag TruthValue
  jnxoptIfOTSnSrcIntervalLastOutputPower Integer32
  jnxoptIfOTSnSrcIntervalLowOutputPower Integer32
  jnxoptIfOTSnSrcIntervalHighOutputPower Integer32
  jnxoptIfOTSnSrcIntervalLastInputPower Integer32
  jnxoptIfOTSnSrcIntervalLowInputPower Integer32
  jnxoptIfOTSnSrcIntervalHighInputPower Integer32

JnxoptIfOTSnSrcCurDayEntry  
SEQUENCE    
  jnxoptIfOTSnSrcCurDaySuspectedFlag TruthValue
  jnxoptIfOTSnSrcCurDayLowOutputPower Integer32
  jnxoptIfOTSnSrcCurDayHighOutputPower Integer32
  jnxoptIfOTSnSrcCurDayLowInputPower Integer32
  jnxoptIfOTSnSrcCurDayHighInputPower Integer32

JnxoptIfOTSnSrcPrevDayEntry  
SEQUENCE    
  jnxoptIfOTSnSrcPrevDaySuspectedFlag TruthValue
  jnxoptIfOTSnSrcPrevDayLastOutputPower Integer32
  jnxoptIfOTSnSrcPrevDayLowOutputPower Integer32
  jnxoptIfOTSnSrcPrevDayHighOutputPower Integer32
  jnxoptIfOTSnSrcPrevDayLastInputPower Integer32
  jnxoptIfOTSnSrcPrevDayLowInputPower Integer32
  jnxoptIfOTSnSrcPrevDayHighInputPower Integer32

JnxoptIfOMSnConfigEntry  
SEQUENCE    
  jnxoptIfOMSnDirectionality JnxoptIfDirectionality
  jnxoptIfOMSnCurrentStatus BITS

JnxoptIfOMSnSinkCurrentEntry  
SEQUENCE    
  jnxoptIfOMSnSinkCurrentSuspectedFlag TruthValue
  jnxoptIfOMSnSinkCurrentAggregatedInputPower Integer32
  jnxoptIfOMSnSinkCurrentLowAggregatedInputPower Integer32
  jnxoptIfOMSnSinkCurrentHighAggregatedInputPower Integer32
  jnxoptIfOMSnSinkCurrentLowerInputPowerThreshold Integer32
  jnxoptIfOMSnSinkCurrentUpperInputPowerThreshold Integer32
  jnxoptIfOMSnSinkCurrentOutputPower Integer32
  jnxoptIfOMSnSinkCurrentLowOutputPower Integer32
  jnxoptIfOMSnSinkCurrentHighOutputPower Integer32
  jnxoptIfOMSnSinkCurrentLowerOutputPowerThreshold Integer32
  jnxoptIfOMSnSinkCurrentUpperOutputPowerThreshold Integer32

JnxoptIfOMSnSinkIntervalEntry  
SEQUENCE    
  jnxoptIfOMSnSinkIntervalNumber JnxoptIfIntervalNumber
  jnxoptIfOMSnSinkIntervalSuspectedFlag TruthValue
  jnxoptIfOMSnSinkIntervalLastAggregatedInputPower Integer32
  jnxoptIfOMSnSinkIntervalLowAggregatedInputPower Integer32
  jnxoptIfOMSnSinkIntervalHighAggregatedInputPower Integer32
  jnxoptIfOMSnSinkIntervalLastOutputPower Integer32
  jnxoptIfOMSnSinkIntervalLowOutputPower Integer32
  jnxoptIfOMSnSinkIntervalHighOutputPower Integer32

JnxoptIfOMSnSinkCurDayEntry  
SEQUENCE    
  jnxoptIfOMSnSinkCurDaySuspectedFlag TruthValue
  jnxoptIfOMSnSinkCurDayLowAggregatedInputPower Integer32
  jnxoptIfOMSnSinkCurDayHighAggregatedInputPower Integer32
  jnxoptIfOMSnSinkCurDayLowOutputPower Integer32
  jnxoptIfOMSnSinkCurDayHighOutputPower Integer32

JnxoptIfOMSnSinkPrevDayEntry  
SEQUENCE    
  jnxoptIfOMSnSinkPrevDaySuspectedFlag TruthValue
  jnxoptIfOMSnSinkPrevDayLastAggregatedInputPower Integer32
  jnxoptIfOMSnSinkPrevDayLowAggregatedInputPower Integer32
  jnxoptIfOMSnSinkPrevDayHighAggregatedInputPower Integer32
  jnxoptIfOMSnSinkPrevDayLastOutputPower Integer32
  jnxoptIfOMSnSinkPrevDayLowOutputPower Integer32
  jnxoptIfOMSnSinkPrevDayHighOutputPower Integer32

JnxoptIfOMSnSrcCurrentEntry  
SEQUENCE    
  jnxoptIfOMSnSrcCurrentSuspectedFlag TruthValue
  jnxoptIfOMSnSrcCurrentOutputPower Integer32
  jnxoptIfOMSnSrcCurrentLowOutputPower Integer32
  jnxoptIfOMSnSrcCurrentHighOutputPower Integer32
  jnxoptIfOMSnSrcCurrentLowerOutputPowerThreshold Integer32
  jnxoptIfOMSnSrcCurrentUpperOutputPowerThreshold Integer32
  jnxoptIfOMSnSrcCurrentAggregatedInputPower Integer32
  jnxoptIfOMSnSrcCurrentLowAggregatedInputPower Integer32
  jnxoptIfOMSnSrcCurrentHighAggregatedInputPower Integer32
  jnxoptIfOMSnSrcCurrentLowerInputPowerThreshold Integer32
  jnxoptIfOMSnSrcCurrentUpperInputPowerThreshold Integer32

JnxoptIfOMSnSrcIntervalEntry  
SEQUENCE    
  jnxoptIfOMSnSrcIntervalNumber JnxoptIfIntervalNumber
  jnxoptIfOMSnSrcIntervalSuspectedFlag TruthValue
  jnxoptIfOMSnSrcIntervalLastOutputPower Integer32
  jnxoptIfOMSnSrcIntervalLowOutputPower Integer32
  jnxoptIfOMSnSrcIntervalHighOutputPower Integer32
  jnxoptIfOMSnSrcIntervalLastAggregatedInputPower Integer32
  jnxoptIfOMSnSrcIntervalLowAggregatedInputPower Integer32
  jnxoptIfOMSnSrcIntervalHighAggregatedInputPower Integer32

JnxoptIfOMSnSrcCurDayEntry  
SEQUENCE    
  jnxoptIfOMSnSrcCurDaySuspectedFlag TruthValue
  jnxoptIfOMSnSrcCurDayLowOutputPower Integer32
  jnxoptIfOMSnSrcCurDayHighOutputPower Integer32
  jnxoptIfOMSnSrcCurDayLowAggregatedInputPower Integer32
  jnxoptIfOMSnSrcCurDayHighAggregatedInputPower Integer32

JnxoptIfOMSnSrcPrevDayEntry  
SEQUENCE    
  jnxoptIfOMSnSrcPrevDaySuspectedFlag TruthValue
  jnxoptIfOMSnSrcPrevDayLastOutputPower Integer32
  jnxoptIfOMSnSrcPrevDayLowOutputPower Integer32
  jnxoptIfOMSnSrcPrevDayHighOutputPower Integer32
  jnxoptIfOMSnSrcPrevDayLastAggregatedInputPower Integer32
  jnxoptIfOMSnSrcPrevDayLowAggregatedInputPower Integer32
  jnxoptIfOMSnSrcPrevDayHighAggregatedInputPower Integer32

JnxoptIfOChGroupConfigEntry  
SEQUENCE    
  jnxoptIfOChGroupDirectionality JnxoptIfDirectionality

JnxoptIfOChGroupSinkCurrentEntry  
SEQUENCE    
  jnxoptIfOChGroupSinkCurrentSuspectedFlag TruthValue
  jnxoptIfOChGroupSinkCurrentAggregatedInputPower Integer32
  jnxoptIfOChGroupSinkCurrentLowAggregatedInputPower Integer32
  jnxoptIfOChGroupSinkCurrentHighAggregatedInputPower Integer32
  jnxoptIfOChGroupSinkCurrentLowerInputPowerThreshold Integer32
  jnxoptIfOChGroupSinkCurrentUpperInputPowerThreshold Integer32
  jnxoptIfOChGroupSinkCurrentOutputPower Integer32
  jnxoptIfOChGroupSinkCurrentLowOutputPower Integer32
  jnxoptIfOChGroupSinkCurrentHighOutputPower Integer32
  jnxoptIfOChGroupSinkCurrentLowerOutputPowerThreshold Integer32
  jnxoptIfOChGroupSinkCurrentUpperOutputPowerThreshold Integer32

JnxoptIfOChGroupSinkIntervalEntry  
SEQUENCE    
  jnxoptIfOChGroupSinkIntervalNumber JnxoptIfIntervalNumber
  jnxoptIfOChGroupSinkIntervalSuspectedFlag TruthValue
  jnxoptIfOChGroupSinkIntervalLastAggregatedInputPower Integer32
  jnxoptIfOChGroupSinkIntervalLowAggregatedInputPower Integer32
  jnxoptIfOChGroupSinkIntervalHighAggregatedInputPower Integer32
  jnxoptIfOChGroupSinkIntervalLastOutputPower Integer32
  jnxoptIfOChGroupSinkIntervalLowOutputPower Integer32
  jnxoptIfOChGroupSinkIntervalHighOutputPower Integer32

JnxoptIfOChGroupSinkCurDayEntry  
SEQUENCE    
  jnxoptIfOChGroupSinkCurDaySuspectedFlag TruthValue
  jnxoptIfOChGroupSinkCurDayLowAggregatedInputPower Integer32
  jnxoptIfOChGroupSinkCurDayHighAggregatedInputPower Integer32
  jnxoptIfOChGroupSinkCurDayLowOutputPower Integer32
  jnxoptIfOChGroupSinkCurDayHighOutputPower Integer32

JnxoptIfOChGroupSinkPrevDayEntry  
SEQUENCE    
  jnxoptIfOChGroupSinkPrevDaySuspectedFlag TruthValue
  jnxoptIfOChGroupSinkPrevDayLastAggregatedInputPower Integer32
  jnxoptIfOChGroupSinkPrevDayLowAggregatedInputPower Integer32
  jnxoptIfOChGroupSinkPrevDayHighAggregatedInputPower Integer32
  jnxoptIfOChGroupSinkPrevDayLastOutputPower Integer32
  jnxoptIfOChGroupSinkPrevDayLowOutputPower Integer32
  jnxoptIfOChGroupSinkPrevDayHighOutputPower Integer32

JnxoptIfOChGroupSrcCurrentEntry  
SEQUENCE    
  jnxoptIfOChGroupSrcCurrentSuspectedFlag TruthValue
  jnxoptIfOChGroupSrcCurrentOutputPower Integer32
  jnxoptIfOChGroupSrcCurrentLowOutputPower Integer32
  jnxoptIfOChGroupSrcCurrentHighOutputPower Integer32
  jnxoptIfOChGroupSrcCurrentLowerOutputPowerThreshold Integer32
  jnxoptIfOChGroupSrcCurrentUpperOutputPowerThreshold Integer32
  jnxoptIfOChGroupSrcCurrentAggregatedInputPower Integer32
  jnxoptIfOChGroupSrcCurrentLowAggregatedInputPower Integer32
  jnxoptIfOChGroupSrcCurrentHighAggregatedInputPower Integer32
  jnxoptIfOChGroupSrcCurrentLowerInputPowerThreshold Integer32
  jnxoptIfOChGroupSrcCurrentUpperInputPowerThreshold Integer32

JnxoptIfOChGroupSrcIntervalEntry  
SEQUENCE    
  jnxoptIfOChGroupSrcIntervalNumber JnxoptIfIntervalNumber
  jnxoptIfOChGroupSrcIntervalSuspectedFlag TruthValue
  jnxoptIfOChGroupSrcIntervalLastOutputPower Integer32
  jnxoptIfOChGroupSrcIntervalLowOutputPower Integer32
  jnxoptIfOChGroupSrcIntervalHighOutputPower Integer32
  jnxoptIfOChGroupSrcIntervalLastAggregatedInputPower Integer32
  jnxoptIfOChGroupSrcIntervalLowAggregatedInputPower Integer32
  jnxoptIfOChGroupSrcIntervalHighAggregatedInputPower Integer32

JnxoptIfOChGroupSrcCurDayEntry  
SEQUENCE    
  jnxoptIfOChGroupSrcCurDaySuspectedFlag TruthValue
  jnxoptIfOChGroupSrcCurDayLowOutputPower Integer32
  jnxoptIfOChGroupSrcCurDayHighOutputPower Integer32
  jnxoptIfOChGroupSrcCurDayLowAggregatedInputPower Integer32
  jnxoptIfOChGroupSrcCurDayHighAggregatedInputPower Integer32

JnxoptIfOChGroupSrcPrevDayEntry  
SEQUENCE    
  jnxoptIfOChGroupSrcPrevDaySuspectedFlag TruthValue
  jnxoptIfOChGroupSrcPrevDayLastOutputPower Integer32
  jnxoptIfOChGroupSrcPrevDayLowOutputPower Integer32
  jnxoptIfOChGroupSrcPrevDayHighOutputPower Integer32
  jnxoptIfOChGroupSrcPrevDayLastAggregatedInputPower Integer32
  jnxoptIfOChGroupSrcPrevDayLowAggregatedInputPower Integer32
  jnxoptIfOChGroupSrcPrevDayHighAggregatedInputPower Integer32

JnxoptIfOChConfigEntry  
SEQUENCE    
  jnxoptIfOChDirectionality JnxoptIfDirectionality
  jnxoptIfOChCurrentStatus BITS

JnxoptIfOChSinkCurrentEntry  
SEQUENCE    
  jnxoptIfOChSinkCurrentSuspectedFlag TruthValue
  jnxoptIfOChSinkCurrentInputPower Integer32
  jnxoptIfOChSinkCurrentLowInputPower Integer32
  jnxoptIfOChSinkCurrentHighInputPower Integer32
  jnxoptIfOChSinkCurrentLowerInputPowerThreshold Integer32
  jnxoptIfOChSinkCurrentUpperInputPowerThreshold Integer32

JnxoptIfOChSinkIntervalEntry  
SEQUENCE    
  jnxoptIfOChSinkIntervalNumber JnxoptIfIntervalNumber
  jnxoptIfOChSinkIntervalSuspectedFlag TruthValue
  jnxoptIfOChSinkIntervalLastInputPower Integer32
  jnxoptIfOChSinkIntervalLowInputPower Integer32
  jnxoptIfOChSinkIntervalHighInputPower Integer32

JnxoptIfOChSinkCurDayEntry  
SEQUENCE    
  jnxoptIfOChSinkCurDaySuspectedFlag TruthValue
  jnxoptIfOChSinkCurDayLowInputPower Integer32
  jnxoptIfOChSinkCurDayHighInputPower Integer32

JnxoptIfOChSinkPrevDayEntry  
SEQUENCE    
  jnxoptIfOChSinkPrevDaySuspectedFlag TruthValue
  jnxoptIfOChSinkPrevDayLastInputPower Integer32
  jnxoptIfOChSinkPrevDayLowInputPower Integer32
  jnxoptIfOChSinkPrevDayHighInputPower Integer32

JnxoptIfOChSrcCurrentEntry  
SEQUENCE    
  jnxoptIfOChSrcCurrentSuspectedFlag TruthValue
  jnxoptIfOChSrcCurrentOutputPower Integer32
  jnxoptIfOChSrcCurrentLowOutputPower Integer32
  jnxoptIfOChSrcCurrentHighOutputPower Integer32
  jnxoptIfOChSrcCurrentLowerOutputPowerThreshold Integer32
  jnxoptIfOChSrcCurrentUpperOutputPowerThreshold Integer32

JnxoptIfOChSrcIntervalEntry  
SEQUENCE    
  jnxoptIfOChSrcIntervalNumber JnxoptIfIntervalNumber
  jnxoptIfOChSrcIntervalSuspectedFlag TruthValue
  jnxoptIfOChSrcIntervalLastOutputPower Integer32
  jnxoptIfOChSrcIntervalLowOutputPower Integer32
  jnxoptIfOChSrcIntervalHighOutputPower Integer32

JnxoptIfOChSrcCurDayEntry  
SEQUENCE    
  jnxoptIfOChSrcCurDaySuspectedFlag TruthValue
  jnxoptIfOChSrcCurDayLowOutputPower Integer32
  jnxoptIfOChSrcCurDayHighOutputPower Integer32

JnxoptIfOChSrcPrevDayEntry  
SEQUENCE    
  jnxoptIfOChSrcPrevDaySuspectedFlag TruthValue
  jnxoptIfOChSrcPrevDayLastOutputPower Integer32
  jnxoptIfOChSrcPrevDayLowOutputPower Integer32
  jnxoptIfOChSrcPrevDayHighOutputPower Integer32

JnxoptIfOTUkConfigEntry  
SEQUENCE    
  jnxoptIfOTUkDirectionality JnxoptIfDirectionality
  jnxoptIfOTUkBitRateK JnxoptIfBitRateK
  jnxoptIfOTUkTraceIdentifierTransmitted JnxoptIfTxTI
  jnxoptIfOTUkDAPIExpected JnxoptIfExDAPI
  jnxoptIfOTUkSAPIExpected JnxoptIfExSAPI
  jnxoptIfOTUkTraceIdentifierAccepted JnxoptIfAcTI
  jnxoptIfOTUkTIMDetMode JnxoptIfTIMDetMode
  jnxoptIfOTUkTIMActEnabled TruthValue
  jnxoptIfOTUkDEGThr JnxoptIfDEGThr
  jnxoptIfOTUkDEGM JnxoptIfDEGM
  jnxoptIfOTUkSinkAdaptActive TruthValue
  jnxoptIfOTUkSourceAdaptActive TruthValue
  jnxoptIfOTUkSinkFECEnabled TruthValue
  jnxoptIfOTUkCurrentStatus BITS

JnxoptIfGCC0ConfigEntry  
SEQUENCE    
  jnxoptIfGCC0Directionality JnxoptIfDirectionality
  jnxoptIfGCC0Application SnmpAdminString
  jnxoptIfGCC0RowStatus RowStatus

JnxoptIfODUkConfigEntry  
SEQUENCE    
  jnxoptIfODUkDirectionality JnxoptIfDirectionality
  jnxoptIfODUkBitRateK JnxoptIfBitRateK
  jnxoptIfODUkTcmFieldsInUse BITS
  jnxoptIfODUkPositionSeqCurrentSize Unsigned32
  jnxoptIfODUkTtpPresent TruthValue

JnxoptIfODUkTtpConfigEntry  
SEQUENCE    
  jnxoptIfODUkTtpTraceIdentifierTransmitted JnxoptIfTxTI
  jnxoptIfODUkTtpDAPIExpected JnxoptIfExDAPI
  jnxoptIfODUkTtpSAPIExpected JnxoptIfExSAPI
  jnxoptIfODUkTtpTraceIdentifierAccepted JnxoptIfAcTI
  jnxoptIfODUkTtpTIMDetMode JnxoptIfTIMDetMode
  jnxoptIfODUkTtpTIMActEnabled TruthValue
  jnxoptIfODUkTtpDEGThr JnxoptIfDEGThr
  jnxoptIfODUkTtpDEGM JnxoptIfDEGM
  jnxoptIfODUkTtpCurrentStatus BITS

JnxoptIfODUkPositionSeqEntry  
SEQUENCE    
  jnxoptIfODUkPositionSeqIndex Unsigned32
  jnxoptIfODUkPositionSeqPosition Unsigned32
  jnxoptIfODUkPositionSeqPointer RowPointer

JnxoptIfODUkNimConfigEntry  
SEQUENCE    
  jnxoptIfODUkNimDirectionality JnxoptIfSinkOrSource
  jnxoptIfODUkNimDAPIExpected JnxoptIfExDAPI
  jnxoptIfODUkNimSAPIExpected JnxoptIfExSAPI
  jnxoptIfODUkNimTraceIdentifierAccepted JnxoptIfAcTI
  jnxoptIfODUkNimTIMDetMode JnxoptIfTIMDetMode
  jnxoptIfODUkNimTIMActEnabled TruthValue
  jnxoptIfODUkNimDEGThr JnxoptIfDEGThr
  jnxoptIfODUkNimDEGM JnxoptIfDEGM
  jnxoptIfODUkNimCurrentStatus BITS
  jnxoptIfODUkNimRowStatus RowStatus

JnxoptIfGCC12ConfigEntry  
SEQUENCE    
  jnxoptIfGCC12Codirectional TruthValue
  jnxoptIfGCC12GCCAccess INTEGER
  jnxoptIfGCC12GCCPassThrough TruthValue
  jnxoptIfGCC12Application SnmpAdminString
  jnxoptIfGCC12RowStatus RowStatus

JnxoptIfODUkTConfigEntry  
SEQUENCE    
  jnxoptIfODUkTTcmField Unsigned32
  jnxoptIfODUkTCodirectional TruthValue
  jnxoptIfODUkTTraceIdentifierTransmitted JnxoptIfTxTI
  jnxoptIfODUkTDAPIExpected JnxoptIfExDAPI
  jnxoptIfODUkTSAPIExpected JnxoptIfExSAPI
  jnxoptIfODUkTTraceIdentifierAccepted JnxoptIfAcTI
  jnxoptIfODUkTTIMDetMode JnxoptIfTIMDetMode
  jnxoptIfODUkTTIMActEnabled TruthValue
  jnxoptIfODUkTDEGThr JnxoptIfDEGThr
  jnxoptIfODUkTDEGM JnxoptIfDEGM
  jnxoptIfODUkTSinkMode INTEGER
  jnxoptIfODUkTSinkLockSignalAdminState INTEGER
  jnxoptIfODUkTSourceLockSignalAdminState INTEGER
  jnxoptIfODUkTCurrentStatus BITS
  jnxoptIfODUkTRowStatus RowStatus

JnxoptIfODUkTNimConfigEntry  
SEQUENCE    
  jnxoptIfODUkTNimTcmField Unsigned32
  jnxoptIfODUkTNimDirectionality JnxoptIfSinkOrSource
  jnxoptIfODUkTNimDAPIExpected JnxoptIfExDAPI
  jnxoptIfODUkTNimSAPIExpected JnxoptIfExSAPI
  jnxoptIfODUkTNimTraceIdentifierAccepted JnxoptIfAcTI
  jnxoptIfODUkTNimTIMDetMode JnxoptIfTIMDetMode
  jnxoptIfODUkTNimTIMActEnabled TruthValue
  jnxoptIfODUkTNimDEGThr JnxoptIfDEGThr
  jnxoptIfODUkTNimDEGM JnxoptIfDEGM
  jnxoptIfODUkTNimCurrentStatus BITS
  jnxoptIfODUkTNimRowStatus RowStatus

Defined Values

jnxoptIfMibModule 1.3.6.1.4.1.2636.3.73.1
The MIB module to describe pre-OTN and OTN interfaces. Copyright (C) The Internet Society (2003). This version of this MIB module is part of RFC 3591; see the RFC itself for full legal notices.
MODULE-IDENTITY    

jnxoptIfObjects 1.3.6.1.4.1.2636.3.73.1.1
OBJECT IDENTIFIER    

jnxoptIfConfs 1.3.6.1.4.1.2636.3.73.1.2
OBJECT IDENTIFIER    

jnxoptIfOTMn 1.3.6.1.4.1.2636.3.73.1.1.1
OBJECT IDENTIFIER    

jnxoptIfPerfMon 1.3.6.1.4.1.2636.3.73.1.1.2
OBJECT IDENTIFIER    

jnxoptIfOTSn 1.3.6.1.4.1.2636.3.73.1.1.3
OBJECT IDENTIFIER    

jnxoptIfOMSn 1.3.6.1.4.1.2636.3.73.1.1.4
OBJECT IDENTIFIER    

jnxoptIfOChGroup 1.3.6.1.4.1.2636.3.73.1.1.5
OBJECT IDENTIFIER    

jnxoptIfOCh 1.3.6.1.4.1.2636.3.73.1.1.6
OBJECT IDENTIFIER    

jnxoptIfOTUk 1.3.6.1.4.1.2636.3.73.1.1.7
OBJECT IDENTIFIER    

jnxoptIfODUk 1.3.6.1.4.1.2636.3.73.1.1.8
OBJECT IDENTIFIER    

jnxoptIfODUkT 1.3.6.1.4.1.2636.3.73.1.1.9
OBJECT IDENTIFIER    

jnxoptIfGroups 1.3.6.1.4.1.2636.3.73.1.2.1
OBJECT IDENTIFIER    

jnxoptIfCompl 1.3.6.1.4.1.2636.3.73.1.2.2
OBJECT IDENTIFIER    

jnxoptIfOTMnTable 1.3.6.1.4.1.2636.3.73.1.1.1.1
A table of OTMn structure information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfOTMnEntry

jnxoptIfOTMnEntry 1.3.6.1.4.1.2636.3.73.1.1.1.1.1
A conceptual row that contains the OTMn structure information of an optical interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfOTMnEntry  

jnxoptIfOTMnOrder 1.3.6.1.4.1.2636.3.73.1.1.1.1.1.1
This object indicates the order of the OTM, which represents the maximum number of wavelengths that can be supported at the bit rate(s) supported on the interface.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..900  

jnxoptIfOTMnReduced 1.3.6.1.4.1.2636.3.73.1.1.1.1.1.2
This object indicates whether a reduced or full functionality is supported at the interface. A value of true means reduced. A value of false means full.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

jnxoptIfOTMnBitRates 1.3.6.1.4.1.2636.3.73.1.1.1.1.1.3
This attribute is a bit map representing the bit rate or set of bit rates supported on the interface. The meaning of each bit position is as follows: bitRateK1(0) is set if the 2.5 Gbit/s rate is supported bitRateK2(1) is set if the 10 Gbit/s rate is supported bitRateK3(2) is set if the 40 Gbit/s rate is supported Note that each bit position corresponds to one possible value of the type JnxoptIfBitRateK. The default value of this attribute is system specific.
Status: current Access: read-only
OBJECT-TYPE    
  BITS bitRateK1(0), bitRateK2(1), bitRateK3(2)  

jnxoptIfOTMnInterfaceType 1.3.6.1.4.1.2636.3.73.1.1.1.1.1.4
This object identifies the type of interface. The value of this attribute will affect the behavior of the OTM with respect to presence/absence of OTM Overhead Signal (OOS) processing and TCM activation. For an IrDI interface, there is no OOS processing and TCM activation is limited to n levels as specified by a TCM level threshold. This object contains two fields that are separated by whitespace. The possible values are: field 1: one of the 4-character ASCII strings 'IrDI' or 'IaDI' field 2: free-form text consisting of printable UTF-8 encoded characters Note that field 2 is optional. If it is not present then there is no requirement for trailing whitespace after field 1. The default values are as follows: field 1: 'IaDI' field 2: an empty string.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

jnxoptIfOTMnTcmMax 1.3.6.1.4.1.2636.3.73.1.1.1.1.1.5
This object identifies the maximum number of TCM levels allowed for any Optical Channel contained in this OTM. A new TCM activation will be rejected if the requested level is greater than the threshold. If InterfaceType object specifies a type of 'IaDI' for this OTM, then this attribute is irrelevant. Possible values: unsigned integers in the range from 0 to 6 inclusive. Default value: 3.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

jnxoptIfOTMnOpticalReach 1.3.6.1.4.1.2636.3.73.1.1.1.1.1.6
This object indicates the length the optical signal may travel before requiring termination or regeneration. The meaning of the enumeration are: intraOffice(1) - intra-office (as defined in ITU-T G.957) shortHaul(2) - short haul (as defined in ITU-T G.957) longHaul(3) - long haul (as defined in ITU-T G.957) veryLongHaul(4) - very long haul (as defined in ITU-T G.691) ultraLongHaul(5)- ultra long haul (as defined in ITU-T G.691)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER intraOffice(1), shortHaul(2), longHaul(3), veryLongHaul(4), ultraLongHaul(5)  

jnxoptIfPerfMonIntervalTable 1.3.6.1.4.1.2636.3.73.1.1.2.1
A table of 15-minute performance monitoring interval information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfPerfMonIntervalEntry

jnxoptIfPerfMonIntervalEntry 1.3.6.1.4.1.2636.3.73.1.1.2.1.1
A conceptual row that contains 15-minute performance monitoring interval information of an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfPerfMonIntervalEntry  

jnxoptIfPerfMonCurrentTimeElapsed 1.3.6.1.4.1.2636.3.73.1.1.2.1.1.1
Number of seconds elapsed in the current 15-minute performance monitoring interval. If, for some reason, such as an adjustment in the NE's time-of-day clock, the number of seconds elapsed exceeds the maximum value, then the maximum value will be returned.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32 0..900  

jnxoptIfPerfMonCurDayTimeElapsed 1.3.6.1.4.1.2636.3.73.1.1.2.1.1.2
Number of seconds elapsed in the current 24-hour interval performance monitoring period. If, for some reason, such as an adjustment in the NE time-of-day clock, the number of seconds elapsed exceeds the maximum value, then the maximum value will be returned.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32 0..86400  

jnxoptIfPerfMonIntervalNumIntervals 1.3.6.1.4.1.2636.3.73.1.1.2.1.1.3
The number of 15-minute intervals for which performance monitoring data is available. The number is the same for all the associated sub layers of the interface. An optical interface must be capable of supporting at least n intervals, where n is defined as follows: The minimum value of n is 4. The default of n is 32. The maximum value of n is 96. The value of this object will be n unless performance monitoring was (re-)started for the interface within the last (n*15) minutes, in which case the value will be the number of complete 15-minute intervals since measurement was (re-)started.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..96  

jnxoptIfPerfMonIntervalNumInvalidIntervals 1.3.6.1.4.1.2636.3.73.1.1.2.1.1.4
The number of intervals in the range from 0 to jnxoptIfPerfMonIntervalNumIntervals for which no performance monitoring data is available and/or the data is invalid.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..96  

jnxoptIfOTSnConfigTable 1.3.6.1.4.1.2636.3.73.1.1.3.1
A table of OTSn configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfOTSnConfigEntry

jnxoptIfOTSnConfigEntry 1.3.6.1.4.1.2636.3.73.1.1.3.1.1
A conceptual row that contains OTSn configuration information of an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfOTSnConfigEntry  

jnxoptIfOTSnDirectionality 1.3.6.1.4.1.2636.3.73.1.1.3.1.1.1
Indicates the directionality of the entity.
Status: current Access: read-only
OBJECT-TYPE    
  JnxoptIfDirectionality  

jnxoptIfOTSnAprStatus 1.3.6.1.4.1.2636.3.73.1.1.3.1.1.2
This attribute indicates the status of the Automatic Power Reduction (APR) function of the entity. Valid values are 'on' and 'off'.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

jnxoptIfOTSnAprControl 1.3.6.1.4.1.2636.3.73.1.1.3.1.1.3
This object is a UTF-8 encoded string that specifies Automatic Power Reduction (APR) control actions requested of this entity (when written) and that returns the current APR control state of this entity (when read). The values are implementation-defined. Any implementation that instantiates this object must document the set of values that it allows to be written, the set of values that it will return, and what each of those values means.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString  

jnxoptIfOTSnTraceIdentifierTransmitted 1.3.6.1.4.1.2636.3.73.1.1.3.1.1.4
The trace identifier transmitted. This object is applicable when jnxoptIfOTSnDirectionality has the value source(2) or bidirectional(3). This object does not apply to reduced-capability systems (i.e., those for which jnxoptIfOTMnReduced has the value true(1)) or at IrDI interfaces (i.e., when jnxoptIfOTMnInterfaceType field 1 has the value 'IrDI'). If no value is ever set by a management entity for the object jnxoptIfOTSnTraceIdentifierTransmitted, system-specific default value will be used. Any implementation that instantiates this object must document the system-specific default value or how it is derived.
Status: current Access: read-write
OBJECT-TYPE    
  JnxoptIfTxTI  

jnxoptIfOTSnDAPIExpected 1.3.6.1.4.1.2636.3.73.1.1.3.1.1.5
The DAPI expected by the receiver. This object is applicable when jnxoptIfOTSnDirectionality has the value sink(1) or bidirectional(3). It has no effect if jnxoptIfOTSnTIMDetMode has the value off(1) or sapi(3). This object does not apply to reduced-capability systems (i.e., those for which jnxoptIfOTMnReduced has the value true(1)) or at IrDI interfaces (i.e., when jnxoptIfOTMnInterfaceType field 1 has the value 'IrDI').
Status: current Access: read-write
OBJECT-TYPE    
  JnxoptIfExDAPI  

jnxoptIfOTSnSAPIExpected 1.3.6.1.4.1.2636.3.73.1.1.3.1.1.6
The SAPI expected by the receiver. This object is applicable when jnxoptIfOTSnDirectionality has the value sink(1) or bidirectional(3). It has no effect if jnxoptIfOTSnTIMDetMode has the value off(1) or dapi(2). This object does not apply to reduced-capability systems (i.e., those for which jnxoptIfOTMnReduced has the value true(1)) or at IrDI interfaces (i.e., when jnxoptIfOTMnInterfaceType field 1 has the value 'IrDI').
Status: current Access: read-write
OBJECT-TYPE    
  JnxoptIfExSAPI  

jnxoptIfOTSnTraceIdentifierAccepted 1.3.6.1.4.1.2636.3.73.1.1.3.1.1.7
The actual trace identifier received. This object is applicable when jnxoptIfOTSnDirectionality has the value sink(1) or bidirectional(3). Its value is unspecified if jnxoptIfOTSnCurrentStatus has either or both of the losO(5) and los(6) bits set. This object does not apply to reduced-capability systems (i.e., those for which jnxoptIfOTMnReduced has the value true(1)) or at IrDI interfaces (i.e., when jnxoptIfOTMnInterfaceType field 1 has the value 'IrDI').
Status: current Access: read-only
OBJECT-TYPE    
  JnxoptIfAcTI  

jnxoptIfOTSnTIMDetMode 1.3.6.1.4.1.2636.3.73.1.1.3.1.1.8
Indicates the mode of the Trace Identifier Mismatch (TIM) Detection function. This object is applicable when jnxoptIfOTSnDirectionality has the value sink(1) or bidirectional(3). The default value is off(1). This object does not apply to reduced-capability systems (i.e., those for which jnxoptIfOTMnReduced has the value true(1)) or at IrDI interfaces (i.e., when jnxoptIfOTMnInterfaceType field 1 has the value 'IrDI'). The default value of this object is off(1).
Status: current Access: read-write
OBJECT-TYPE    
  JnxoptIfTIMDetMode  

jnxoptIfOTSnTIMActEnabled 1.3.6.1.4.1.2636.3.73.1.1.3.1.1.9
Indicates whether the Trace Identifier Mismatch (TIM) Consequent Action function is enabled. This object is applicable when jnxoptIfOTSnDirectionality has the value sink(1) or bidirectional(3). It has no effect when the value of jnxoptIfOTSnTIMDetMode is off(1). This object does not apply to reduced-capability systems (i.e., those for which jnxoptIfOTMnReduced has the value true(1)) or at IrDI interfaces (i.e., when jnxoptIfOTMnInterfaceType field 1 has the value 'IrDI'). The default value of this object is false(2).
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxoptIfOTSnCurrentStatus 1.3.6.1.4.1.2636.3.73.1.1.3.1.1.10
Indicates the defect condition of the entity, if any. This object is applicable when jnxoptIfOTSnDirectionality has the value sink(1) or bidirectional(3). In reduced-capability systems or at IrDI interfaces the only bit position that may be set is los(6).
Status: current Access: read-only
OBJECT-TYPE    
  BITS bdiP(0), bdiO(1), bdi(2), tim(3), losP(4), losO(5), los(6)  

jnxoptIfOTSnSinkCurrentTable 1.3.6.1.4.1.2636.3.73.1.1.3.2
A table of OTSn sink performance monitoring information for the current 15-minute interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfOTSnSinkCurrentEntry

jnxoptIfOTSnSinkCurrentEntry 1.3.6.1.4.1.2636.3.73.1.1.3.2.1
A conceptual row that contains OTSn sink performance monitoring information of an interface for the current 15-minute interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfOTSnSinkCurrentEntry  

jnxoptIfOTSnSinkCurrentSuspectedFlag 1.3.6.1.4.1.2636.3.73.1.1.3.2.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

jnxoptIfOTSnSinkCurrentInputPower 1.3.6.1.4.1.2636.3.73.1.1.3.2.1.2
The optical power monitored at the input.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSinkCurrentLowInputPower 1.3.6.1.4.1.2636.3.73.1.1.3.2.1.3
The lowest optical power monitored at the input during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSinkCurrentHighInputPower 1.3.6.1.4.1.2636.3.73.1.1.3.2.1.4
The highest optical power monitored at the input during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSinkCurrentLowerInputPowerThreshold 1.3.6.1.4.1.2636.3.73.1.1.3.2.1.5
The lower limit threshold on input power. If jnxoptIfOTSnSinkCurrentInputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSinkCurrentUpperInputPowerThreshold 1.3.6.1.4.1.2636.3.73.1.1.3.2.1.6
The upper limit threshold on input power. If jnxoptIfOTSnSinkCurrentInputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSinkCurrentOutputPower 1.3.6.1.4.1.2636.3.73.1.1.3.2.1.7
The optical power monitored at the output.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSinkCurrentLowOutputPower 1.3.6.1.4.1.2636.3.73.1.1.3.2.1.8
The lowest optical power monitored at the output during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSinkCurrentHighOutputPower 1.3.6.1.4.1.2636.3.73.1.1.3.2.1.9
The highest optical power monitored at the output during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSinkCurrentLowerOutputPowerThreshold 1.3.6.1.4.1.2636.3.73.1.1.3.2.1.10
The lower limit threshold on output power. If jnxoptIfOTSnSinkCurrentOutputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSinkCurrentUpperOutputPowerThreshold 1.3.6.1.4.1.2636.3.73.1.1.3.2.1.11
The upper limit threshold on output power. If jnxoptIfOTSnSinkCurrentOutputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSinkIntervalTable 1.3.6.1.4.1.2636.3.73.1.1.3.3
A table of historical OTSn sink performance monitoring information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfOTSnSinkIntervalEntry

jnxoptIfOTSnSinkIntervalEntry 1.3.6.1.4.1.2636.3.73.1.1.3.3.1
A conceptual row that contains OTSn sink performance monitoring information of an interface during a particular historical interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfOTSnSinkIntervalEntry  

jnxoptIfOTSnSinkIntervalNumber 1.3.6.1.4.1.2636.3.73.1.1.3.3.1.1
Uniquely identifies the interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfIntervalNumber  

jnxoptIfOTSnSinkIntervalSuspectedFlag 1.3.6.1.4.1.2636.3.73.1.1.3.3.1.2
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

jnxoptIfOTSnSinkIntervalLastInputPower 1.3.6.1.4.1.2636.3.73.1.1.3.3.1.3
The last optical power monitored at the input during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSinkIntervalLowInputPower 1.3.6.1.4.1.2636.3.73.1.1.3.3.1.4
The lowest optical power monitored at the input during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSinkIntervalHighInputPower 1.3.6.1.4.1.2636.3.73.1.1.3.3.1.5
The highest optical power monitored at the input during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSinkIntervalLastOutputPower 1.3.6.1.4.1.2636.3.73.1.1.3.3.1.6
The last optical power monitored at the output during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSinkIntervalLowOutputPower 1.3.6.1.4.1.2636.3.73.1.1.3.3.1.7
The lowest optical power monitored at the output during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSinkIntervalHighOutputPower 1.3.6.1.4.1.2636.3.73.1.1.3.3.1.8
The highest optical power monitored at the output during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSinkCurDayTable 1.3.6.1.4.1.2636.3.73.1.1.3.4
A table of OTSn sink performance monitoring information for the current 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfOTSnSinkCurDayEntry

jnxoptIfOTSnSinkCurDayEntry 1.3.6.1.4.1.2636.3.73.1.1.3.4.1
A conceptual row that contains OTSn sink performance monitoring information of an interface for the current 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfOTSnSinkCurDayEntry  

jnxoptIfOTSnSinkCurDaySuspectedFlag 1.3.6.1.4.1.2636.3.73.1.1.3.4.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

jnxoptIfOTSnSinkCurDayLowInputPower 1.3.6.1.4.1.2636.3.73.1.1.3.4.1.2
The lowest optical power monitored at the input during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSinkCurDayHighInputPower 1.3.6.1.4.1.2636.3.73.1.1.3.4.1.3
The highest optical power monitored at the input during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSinkCurDayLowOutputPower 1.3.6.1.4.1.2636.3.73.1.1.3.4.1.4
The lowest optical power monitored at the output during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSinkCurDayHighOutputPower 1.3.6.1.4.1.2636.3.73.1.1.3.4.1.5
The highest optical power monitored at the output during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSinkPrevDayTable 1.3.6.1.4.1.2636.3.73.1.1.3.5
A table of OTSn sink performance monitoring information for the previous 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfOTSnSinkPrevDayEntry

jnxoptIfOTSnSinkPrevDayEntry 1.3.6.1.4.1.2636.3.73.1.1.3.5.1
A conceptual row that contains OTSn sink performance monitoring information of an interface for the previous 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfOTSnSinkPrevDayEntry  

jnxoptIfOTSnSinkPrevDaySuspectedFlag 1.3.6.1.4.1.2636.3.73.1.1.3.5.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

jnxoptIfOTSnSinkPrevDayLastInputPower 1.3.6.1.4.1.2636.3.73.1.1.3.5.1.2
The last optical power monitored at the input during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSinkPrevDayLowInputPower 1.3.6.1.4.1.2636.3.73.1.1.3.5.1.3
The lowest optical power monitored at the input during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSinkPrevDayHighInputPower 1.3.6.1.4.1.2636.3.73.1.1.3.5.1.4
The highest optical power monitored at the input during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSinkPrevDayLastOutputPower 1.3.6.1.4.1.2636.3.73.1.1.3.5.1.5
The last optical power monitored at the output during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSinkPrevDayLowOutputPower 1.3.6.1.4.1.2636.3.73.1.1.3.5.1.6
The lowest optical power monitored at the output during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSinkPrevDayHighOutputPower 1.3.6.1.4.1.2636.3.73.1.1.3.5.1.7
The highest optical power monitored at the output during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSrcCurrentTable 1.3.6.1.4.1.2636.3.73.1.1.3.6
A table of OTSn source performance monitoring information for the current 15-minute interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfOTSnSrcCurrentEntry

jnxoptIfOTSnSrcCurrentEntry 1.3.6.1.4.1.2636.3.73.1.1.3.6.1
A conceptual row that contains OTSn source performance monitoring information of an interface for the current 15-minute interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfOTSnSrcCurrentEntry  

jnxoptIfOTSnSrcCurrentSuspectedFlag 1.3.6.1.4.1.2636.3.73.1.1.3.6.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

jnxoptIfOTSnSrcCurrentOutputPower 1.3.6.1.4.1.2636.3.73.1.1.3.6.1.2
The optical power monitored at the output.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSrcCurrentLowOutputPower 1.3.6.1.4.1.2636.3.73.1.1.3.6.1.3
The lowest optical power monitored at the output during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSrcCurrentHighOutputPower 1.3.6.1.4.1.2636.3.73.1.1.3.6.1.4
The highest optical power monitored at the output during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSrcCurrentLowerOutputPowerThreshold 1.3.6.1.4.1.2636.3.73.1.1.3.6.1.5
The lower limit threshold on output power. If jnxoptIfOTSnSrcCurrentOutputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSrcCurrentUpperOutputPowerThreshold 1.3.6.1.4.1.2636.3.73.1.1.3.6.1.6
The upper limit threshold on output power. If jnxoptIfOTSnSrcCurrentOutputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSrcCurrentInputPower 1.3.6.1.4.1.2636.3.73.1.1.3.6.1.7
The optical power monitored at the input.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSrcCurrentLowInputPower 1.3.6.1.4.1.2636.3.73.1.1.3.6.1.8
The lowest optical power monitored at the input during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSrcCurrentHighInputPower 1.3.6.1.4.1.2636.3.73.1.1.3.6.1.9
The highest optical power monitored at the input during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSrcCurrentLowerInputPowerThreshold 1.3.6.1.4.1.2636.3.73.1.1.3.6.1.10
The lower limit threshold on input power. If jnxoptIfOTSnSrcCurrentInputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSrcCurrentUpperInputPowerThreshold 1.3.6.1.4.1.2636.3.73.1.1.3.6.1.11
The upper limit threshold on input power. If jnxoptIfOTSnSrcCurrentInputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSrcIntervalTable 1.3.6.1.4.1.2636.3.73.1.1.3.7
A table of historical OTSn source performance monitoring information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfOTSnSrcIntervalEntry

jnxoptIfOTSnSrcIntervalEntry 1.3.6.1.4.1.2636.3.73.1.1.3.7.1
A conceptual row that contains OTSn source performance monitoring information of an interface during a particular historical interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfOTSnSrcIntervalEntry  

jnxoptIfOTSnSrcIntervalNumber 1.3.6.1.4.1.2636.3.73.1.1.3.7.1.1
Uniquely identifies the interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfIntervalNumber  

jnxoptIfOTSnSrcIntervalSuspectedFlag 1.3.6.1.4.1.2636.3.73.1.1.3.7.1.2
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

jnxoptIfOTSnSrcIntervalLastOutputPower 1.3.6.1.4.1.2636.3.73.1.1.3.7.1.3
The last optical power monitored at the output during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSrcIntervalLowOutputPower 1.3.6.1.4.1.2636.3.73.1.1.3.7.1.4
The lowest optical power monitored at the output during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSrcIntervalHighOutputPower 1.3.6.1.4.1.2636.3.73.1.1.3.7.1.5
The highest optical power monitored at the output during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSrcIntervalLastInputPower 1.3.6.1.4.1.2636.3.73.1.1.3.7.1.6
The last optical power monitored at the input during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSrcIntervalLowInputPower 1.3.6.1.4.1.2636.3.73.1.1.3.7.1.7
The lowest optical power monitored at the input during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSrcIntervalHighInputPower 1.3.6.1.4.1.2636.3.73.1.1.3.7.1.8
The highest optical power monitored at the input during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSrcCurDayTable 1.3.6.1.4.1.2636.3.73.1.1.3.8
A table of OTSn source performance monitoring information for the current 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfOTSnSrcCurDayEntry

jnxoptIfOTSnSrcCurDayEntry 1.3.6.1.4.1.2636.3.73.1.1.3.8.1
A conceptual row that contains OTSn source performance monitoring information of an interface for the current 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfOTSnSrcCurDayEntry  

jnxoptIfOTSnSrcCurDaySuspectedFlag 1.3.6.1.4.1.2636.3.73.1.1.3.8.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

jnxoptIfOTSnSrcCurDayLowOutputPower 1.3.6.1.4.1.2636.3.73.1.1.3.8.1.2
The lowest optical power monitored at the output during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSrcCurDayHighOutputPower 1.3.6.1.4.1.2636.3.73.1.1.3.8.1.3
The highest optical power monitored at the output during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSrcCurDayLowInputPower 1.3.6.1.4.1.2636.3.73.1.1.3.8.1.4
The lowest optical power monitored at the input during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSrcCurDayHighInputPower 1.3.6.1.4.1.2636.3.73.1.1.3.8.1.5
The highest optical power monitored at the input during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSrcPrevDayTable 1.3.6.1.4.1.2636.3.73.1.1.3.9
A table of OTSn source performance monitoring information for the previous 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfOTSnSrcPrevDayEntry

jnxoptIfOTSnSrcPrevDayEntry 1.3.6.1.4.1.2636.3.73.1.1.3.9.1
A conceptual row that contains OTSn source performance monitoring information of an interface for the previous 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfOTSnSrcPrevDayEntry  

jnxoptIfOTSnSrcPrevDaySuspectedFlag 1.3.6.1.4.1.2636.3.73.1.1.3.9.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

jnxoptIfOTSnSrcPrevDayLastOutputPower 1.3.6.1.4.1.2636.3.73.1.1.3.9.1.2
The last optical power monitored at the output during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSrcPrevDayLowOutputPower 1.3.6.1.4.1.2636.3.73.1.1.3.9.1.3
The lowest optical power monitored at the output during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSrcPrevDayHighOutputPower 1.3.6.1.4.1.2636.3.73.1.1.3.9.1.4
The highest optical power monitored at the output during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSrcPrevDayLastInputPower 1.3.6.1.4.1.2636.3.73.1.1.3.9.1.5
The last optical power monitored at the input during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSrcPrevDayLowInputPower 1.3.6.1.4.1.2636.3.73.1.1.3.9.1.6
The lowest optical power monitored at the input during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTSnSrcPrevDayHighInputPower 1.3.6.1.4.1.2636.3.73.1.1.3.9.1.7
The highest optical power monitored at the input during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnConfigTable 1.3.6.1.4.1.2636.3.73.1.1.4.1
A table of OMSn configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfOMSnConfigEntry

jnxoptIfOMSnConfigEntry 1.3.6.1.4.1.2636.3.73.1.1.4.1.1
A conceptual row that contains OMSn configuration information of an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfOMSnConfigEntry  

jnxoptIfOMSnDirectionality 1.3.6.1.4.1.2636.3.73.1.1.4.1.1.1
Indicates the directionality of the entity.
Status: current Access: read-only
OBJECT-TYPE    
  JnxoptIfDirectionality  

jnxoptIfOMSnCurrentStatus 1.3.6.1.4.1.2636.3.73.1.1.4.1.1.2
Indicates the defect condition of the entity, if any. This object is applicable only to full capability systems whose interface type is IaDI and for which jnxoptIfOMSnDirectionality has the value sink(1) or bidirectional(3).
Status: current Access: read-only
OBJECT-TYPE    
  BITS ssfP(0), ssfO(1), ssf(2), bdiP(3), bdiO(4), bdi(5), losP(6)  

jnxoptIfOMSnSinkCurrentTable 1.3.6.1.4.1.2636.3.73.1.1.4.2
A table of OMSn sink performance monitoring information for the current 15-minute interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfOMSnSinkCurrentEntry

jnxoptIfOMSnSinkCurrentEntry 1.3.6.1.4.1.2636.3.73.1.1.4.2.1
A conceptual row that contains OMSn sink performance monitoring information of an interface for the current 15-minute interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfOMSnSinkCurrentEntry  

jnxoptIfOMSnSinkCurrentSuspectedFlag 1.3.6.1.4.1.2636.3.73.1.1.4.2.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

jnxoptIfOMSnSinkCurrentAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.4.2.1.2
The aggregated optical power of all the DWDM input channels.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSinkCurrentLowAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.4.2.1.3
The lowest aggregated optical power of all the DWDM input channels during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSinkCurrentHighAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.4.2.1.4
The highest aggregated optical power of all the DWDM input channels during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSinkCurrentLowerInputPowerThreshold 1.3.6.1.4.1.2636.3.73.1.1.4.2.1.5
The lower limit threshold on aggregated input power. If jnxoptIfOMSnSinkCurrentAggregatedInputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSinkCurrentUpperInputPowerThreshold 1.3.6.1.4.1.2636.3.73.1.1.4.2.1.6
The upper limit threshold on aggregated input power. If jnxoptIfOMSnSinkCurrentAggregatedInputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSinkCurrentOutputPower 1.3.6.1.4.1.2636.3.73.1.1.4.2.1.7
The optical power monitored at the output.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSinkCurrentLowOutputPower 1.3.6.1.4.1.2636.3.73.1.1.4.2.1.8
The lowest optical power monitored at the output during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSinkCurrentHighOutputPower 1.3.6.1.4.1.2636.3.73.1.1.4.2.1.9
The highest optical power monitored at the output during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSinkCurrentLowerOutputPowerThreshold 1.3.6.1.4.1.2636.3.73.1.1.4.2.1.10
The lower limit threshold on output power. If jnxoptIfOMSnSinkCurrentOutputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSinkCurrentUpperOutputPowerThreshold 1.3.6.1.4.1.2636.3.73.1.1.4.2.1.11
The upper limit threshold on output power. If jnxoptIfOMSnSinkCurrentOutputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSinkIntervalTable 1.3.6.1.4.1.2636.3.73.1.1.4.3
A table of historical OMSn sink performance monitoring information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfOMSnSinkIntervalEntry

jnxoptIfOMSnSinkIntervalEntry 1.3.6.1.4.1.2636.3.73.1.1.4.3.1
A conceptual row that contains OMSn sink performance monitoring information of an interface during a particular historical interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfOMSnSinkIntervalEntry  

jnxoptIfOMSnSinkIntervalNumber 1.3.6.1.4.1.2636.3.73.1.1.4.3.1.1
Uniquely identifies the interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfIntervalNumber  

jnxoptIfOMSnSinkIntervalSuspectedFlag 1.3.6.1.4.1.2636.3.73.1.1.4.3.1.2
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

jnxoptIfOMSnSinkIntervalLastAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.4.3.1.3
The last aggregated optical power of all the DWDM input channels during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSinkIntervalLowAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.4.3.1.4
The lowest aggregated optical power of all the DWDM input channels during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSinkIntervalHighAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.4.3.1.5
The highest aggregated optical power of all the DWDM input channels during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSinkIntervalLastOutputPower 1.3.6.1.4.1.2636.3.73.1.1.4.3.1.6
The last optical power at the output during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSinkIntervalLowOutputPower 1.3.6.1.4.1.2636.3.73.1.1.4.3.1.7
The lowest optical power at the output during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSinkIntervalHighOutputPower 1.3.6.1.4.1.2636.3.73.1.1.4.3.1.8
The highest optical power at the output during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSinkCurDayTable 1.3.6.1.4.1.2636.3.73.1.1.4.4
A table of OMSn sink performance monitoring information for the current 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfOMSnSinkCurDayEntry

jnxoptIfOMSnSinkCurDayEntry 1.3.6.1.4.1.2636.3.73.1.1.4.4.1
A conceptual row that contains OMSn sink performance monitoring information of an interface for the current 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfOMSnSinkCurDayEntry  

jnxoptIfOMSnSinkCurDaySuspectedFlag 1.3.6.1.4.1.2636.3.73.1.1.4.4.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

jnxoptIfOMSnSinkCurDayLowAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.4.4.1.2
The lowest aggregated optical power of all the DWDM input channels during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSinkCurDayHighAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.4.4.1.3
The highest aggregated optical power of all the DWDM input channels during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSinkCurDayLowOutputPower 1.3.6.1.4.1.2636.3.73.1.1.4.4.1.4
The lowest optical power at the output during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSinkCurDayHighOutputPower 1.3.6.1.4.1.2636.3.73.1.1.4.4.1.5
The highest optical power at the output during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSinkPrevDayTable 1.3.6.1.4.1.2636.3.73.1.1.4.5
A table of OMSn sink performance monitoring information for the previous 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfOMSnSinkPrevDayEntry

jnxoptIfOMSnSinkPrevDayEntry 1.3.6.1.4.1.2636.3.73.1.1.4.5.1
A conceptual row that contains OMSn sink performance monitoring information of an interface for the previous 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfOMSnSinkPrevDayEntry  

jnxoptIfOMSnSinkPrevDaySuspectedFlag 1.3.6.1.4.1.2636.3.73.1.1.4.5.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

jnxoptIfOMSnSinkPrevDayLastAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.4.5.1.2
The last aggregated optical power of all the DWDM input channels during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSinkPrevDayLowAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.4.5.1.3
The lowest aggregated optical power of all the DWDM input channels during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSinkPrevDayHighAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.4.5.1.4
The highest aggregated optical power of all the DWDM input channels during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSinkPrevDayLastOutputPower 1.3.6.1.4.1.2636.3.73.1.1.4.5.1.5
The last optical power at the output during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSinkPrevDayLowOutputPower 1.3.6.1.4.1.2636.3.73.1.1.4.5.1.6
The lowest optical power at the output during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSinkPrevDayHighOutputPower 1.3.6.1.4.1.2636.3.73.1.1.4.5.1.7
The highest optical power at the output during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSrcCurrentTable 1.3.6.1.4.1.2636.3.73.1.1.4.6
A table of OMSn source performance monitoring information for the current 15-minute interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfOMSnSrcCurrentEntry

jnxoptIfOMSnSrcCurrentEntry 1.3.6.1.4.1.2636.3.73.1.1.4.6.1
A conceptual row that contains OMSn source performance monitoring information of an interface for the current 15-minute interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfOMSnSrcCurrentEntry  

jnxoptIfOMSnSrcCurrentSuspectedFlag 1.3.6.1.4.1.2636.3.73.1.1.4.6.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

jnxoptIfOMSnSrcCurrentOutputPower 1.3.6.1.4.1.2636.3.73.1.1.4.6.1.2
The optical power monitored at the output.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSrcCurrentLowOutputPower 1.3.6.1.4.1.2636.3.73.1.1.4.6.1.3
The lowest optical power monitored at the output during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSrcCurrentHighOutputPower 1.3.6.1.4.1.2636.3.73.1.1.4.6.1.4
The highest optical power monitored at the output during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSrcCurrentLowerOutputPowerThreshold 1.3.6.1.4.1.2636.3.73.1.1.4.6.1.5
The lower limit threshold on output power. If jnxoptIfOMSnSrcCurrentOutputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSrcCurrentUpperOutputPowerThreshold 1.3.6.1.4.1.2636.3.73.1.1.4.6.1.6
The upper limit threshold on output power. If jnxoptIfOMSnSrcCurrentOutputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSrcCurrentAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.4.6.1.7
The aggregated optical power at the input.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSrcCurrentLowAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.4.6.1.8
The lowest aggregated optical power at the input during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSrcCurrentHighAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.4.6.1.9
The highest aggregated optical power at the input during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSrcCurrentLowerInputPowerThreshold 1.3.6.1.4.1.2636.3.73.1.1.4.6.1.10
The lower limit threshold on aggregated input power. If jnxoptIfOMSnSrcCurrentAggregatedInputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSrcCurrentUpperInputPowerThreshold 1.3.6.1.4.1.2636.3.73.1.1.4.6.1.11
The upper limit threshold on aggregated input power. If jnxoptIfOMSnSrcCurrentAggregatedInputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSrcIntervalTable 1.3.6.1.4.1.2636.3.73.1.1.4.7
A table of historical OMSn source performance monitoring information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfOMSnSrcIntervalEntry

jnxoptIfOMSnSrcIntervalEntry 1.3.6.1.4.1.2636.3.73.1.1.4.7.1
A conceptual row that contains OMSn source performance monitoring information of an interface during a particular historical interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfOMSnSrcIntervalEntry  

jnxoptIfOMSnSrcIntervalNumber 1.3.6.1.4.1.2636.3.73.1.1.4.7.1.1
Uniquely identifies the interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfIntervalNumber  

jnxoptIfOMSnSrcIntervalSuspectedFlag 1.3.6.1.4.1.2636.3.73.1.1.4.7.1.2
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

jnxoptIfOMSnSrcIntervalLastOutputPower 1.3.6.1.4.1.2636.3.73.1.1.4.7.1.3
The last optical power monitored at the output during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSrcIntervalLowOutputPower 1.3.6.1.4.1.2636.3.73.1.1.4.7.1.4
The lowest optical power monitored at the output during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSrcIntervalHighOutputPower 1.3.6.1.4.1.2636.3.73.1.1.4.7.1.5
The highest optical power monitored at the output during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSrcIntervalLastAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.4.7.1.6
The last aggregated optical power at the input during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSrcIntervalLowAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.4.7.1.7
The lowest aggregated optical power at the input during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSrcIntervalHighAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.4.7.1.8
The highest aggregated optical power at the input during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSrcCurDayTable 1.3.6.1.4.1.2636.3.73.1.1.4.8
A table of OMSn source performance monitoring information for the current 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfOMSnSrcCurDayEntry

jnxoptIfOMSnSrcCurDayEntry 1.3.6.1.4.1.2636.3.73.1.1.4.8.1
A conceptual row that contains OMSn source performance monitoring information of an interface for the current 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfOMSnSrcCurDayEntry  

jnxoptIfOMSnSrcCurDaySuspectedFlag 1.3.6.1.4.1.2636.3.73.1.1.4.8.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

jnxoptIfOMSnSrcCurDayLowOutputPower 1.3.6.1.4.1.2636.3.73.1.1.4.8.1.2
The lowest optical power monitored at the output during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSrcCurDayHighOutputPower 1.3.6.1.4.1.2636.3.73.1.1.4.8.1.3
The highest optical power monitored at the output during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSrcCurDayLowAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.4.8.1.4
The lowest aggregated optical power at the input during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSrcCurDayHighAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.4.8.1.5
The highest aggregated optical power at the input during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSrcPrevDayTable 1.3.6.1.4.1.2636.3.73.1.1.4.9
A table of OMSn source performance monitoring information for the previous 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfOMSnSrcPrevDayEntry

jnxoptIfOMSnSrcPrevDayEntry 1.3.6.1.4.1.2636.3.73.1.1.4.9.1
A conceptual row that contains OMSn source performance monitoring information of an interface for the previous 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfOMSnSrcPrevDayEntry  

jnxoptIfOMSnSrcPrevDaySuspectedFlag 1.3.6.1.4.1.2636.3.73.1.1.4.9.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

jnxoptIfOMSnSrcPrevDayLastOutputPower 1.3.6.1.4.1.2636.3.73.1.1.4.9.1.2
The last optical power monitored at the output during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSrcPrevDayLowOutputPower 1.3.6.1.4.1.2636.3.73.1.1.4.9.1.3
The lowest optical power monitored at the output during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSrcPrevDayHighOutputPower 1.3.6.1.4.1.2636.3.73.1.1.4.9.1.4
The highest optical power monitored at the output during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSrcPrevDayLastAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.4.9.1.5
The last aggregated optical power at the input during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSrcPrevDayLowAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.4.9.1.6
The lowest aggregated optical power at the input during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOMSnSrcPrevDayHighAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.4.9.1.7
The highest aggregated optical power at the input during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupConfigTable 1.3.6.1.4.1.2636.3.73.1.1.5.1
A table of OChGroup configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfOChGroupConfigEntry

jnxoptIfOChGroupConfigEntry 1.3.6.1.4.1.2636.3.73.1.1.5.1.1
A conceptual row that contains OChGroup configuration information of an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfOChGroupConfigEntry  

jnxoptIfOChGroupDirectionality 1.3.6.1.4.1.2636.3.73.1.1.5.1.1.1
Indicates the directionality of the entity.
Status: current Access: read-only
OBJECT-TYPE    
  JnxoptIfDirectionality  

jnxoptIfOChGroupSinkCurrentTable 1.3.6.1.4.1.2636.3.73.1.1.5.2
A table of OChGroup sink performance monitoring information for the current 15-minute interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfOChGroupSinkCurrentEntry

jnxoptIfOChGroupSinkCurrentEntry 1.3.6.1.4.1.2636.3.73.1.1.5.2.1
A conceptual row that contains OChGroup sink performance monitoring information of an interface for the current 15-minute interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfOChGroupSinkCurrentEntry  

jnxoptIfOChGroupSinkCurrentSuspectedFlag 1.3.6.1.4.1.2636.3.73.1.1.5.2.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

jnxoptIfOChGroupSinkCurrentAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.5.2.1.2
The aggregated optical power of all the DWDM input channels in the OChGroup.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSinkCurrentLowAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.5.2.1.3
The lowest aggregated optical power of all the DWDM input channels in the OChGroup during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSinkCurrentHighAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.5.2.1.4
The highest aggregated optical power of all the DWDM input channels in the OChGroup during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSinkCurrentLowerInputPowerThreshold 1.3.6.1.4.1.2636.3.73.1.1.5.2.1.5
The lower limit threshold on aggregated input power. If jnxoptIfOChGroupSinkCurrentAggregatedInputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSinkCurrentUpperInputPowerThreshold 1.3.6.1.4.1.2636.3.73.1.1.5.2.1.6
The upper limit threshold on aggregated input power. If jnxoptIfOChGroupSinkCurrentAggregatedInputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSinkCurrentOutputPower 1.3.6.1.4.1.2636.3.73.1.1.5.2.1.7
The optical power monitored at the output in the OChGroup.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSinkCurrentLowOutputPower 1.3.6.1.4.1.2636.3.73.1.1.5.2.1.8
The lowest optical power monitored at the output in the OChGroup during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSinkCurrentHighOutputPower 1.3.6.1.4.1.2636.3.73.1.1.5.2.1.9
The highest optical power monitored at the output in the OChGroup during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSinkCurrentLowerOutputPowerThreshold 1.3.6.1.4.1.2636.3.73.1.1.5.2.1.10
The lower limit threshold on the output power. If jnxoptIfOChGroupSinkCurrentOutputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSinkCurrentUpperOutputPowerThreshold 1.3.6.1.4.1.2636.3.73.1.1.5.2.1.11
The upper limit threshold on the output power. If jnxoptIfOChGroupSinkCurrentOutputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSinkIntervalTable 1.3.6.1.4.1.2636.3.73.1.1.5.3
A table of historical OChGroup sink performance monitoring information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfOChGroupSinkIntervalEntry

jnxoptIfOChGroupSinkIntervalEntry 1.3.6.1.4.1.2636.3.73.1.1.5.3.1
A conceptual row that contains OChGroup sink performance monitoring information of an interface during a particular historical interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfOChGroupSinkIntervalEntry  

jnxoptIfOChGroupSinkIntervalNumber 1.3.6.1.4.1.2636.3.73.1.1.5.3.1.1
Uniquely identifies the interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfIntervalNumber  

jnxoptIfOChGroupSinkIntervalSuspectedFlag 1.3.6.1.4.1.2636.3.73.1.1.5.3.1.2
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

jnxoptIfOChGroupSinkIntervalLastAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.5.3.1.3
The last aggregated optical power of all the DWDM input channels in the OChGroup during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSinkIntervalLowAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.5.3.1.4
The lowest aggregated optical power of all the DWDM input channels in the OChGroup during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSinkIntervalHighAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.5.3.1.5
The highest aggregated optical power of all the DWDM input channels in the OChGroup during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSinkIntervalLastOutputPower 1.3.6.1.4.1.2636.3.73.1.1.5.3.1.6
The last optical power monitored at the output in the OChGroup during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSinkIntervalLowOutputPower 1.3.6.1.4.1.2636.3.73.1.1.5.3.1.7
The lowest optical power monitored at the output in the OChGroup during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSinkIntervalHighOutputPower 1.3.6.1.4.1.2636.3.73.1.1.5.3.1.8
The highest optical power monitored at the output in the OChGroup during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSinkCurDayTable 1.3.6.1.4.1.2636.3.73.1.1.5.4
A table of OChGroup sink performance monitoring information for the current 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfOChGroupSinkCurDayEntry

jnxoptIfOChGroupSinkCurDayEntry 1.3.6.1.4.1.2636.3.73.1.1.5.4.1
A conceptual row that contains OChGroup sink performance monitoring information of an interface for the current 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfOChGroupSinkCurDayEntry  

jnxoptIfOChGroupSinkCurDaySuspectedFlag 1.3.6.1.4.1.2636.3.73.1.1.5.4.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

jnxoptIfOChGroupSinkCurDayLowAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.5.4.1.2
The lowest aggregated optical power of all the DWDM input channels in the OChGroup during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSinkCurDayHighAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.5.4.1.3
The highest aggregated optical power of all the DWDM input channels in the OChGroup during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSinkCurDayLowOutputPower 1.3.6.1.4.1.2636.3.73.1.1.5.4.1.4
The lowest optical power monitored at the output in the OChGroup during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSinkCurDayHighOutputPower 1.3.6.1.4.1.2636.3.73.1.1.5.4.1.5
The highest optical power monitored at the output in the OChGroup during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSinkPrevDayTable 1.3.6.1.4.1.2636.3.73.1.1.5.5
A table of OChGroup sink performance monitoring information for the previous 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfOChGroupSinkPrevDayEntry

jnxoptIfOChGroupSinkPrevDayEntry 1.3.6.1.4.1.2636.3.73.1.1.5.5.1
A conceptual row that contains OChGroup sink performance monitoring information of an interface for the previous 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfOChGroupSinkPrevDayEntry  

jnxoptIfOChGroupSinkPrevDaySuspectedFlag 1.3.6.1.4.1.2636.3.73.1.1.5.5.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

jnxoptIfOChGroupSinkPrevDayLastAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.5.5.1.2
The last aggregated optical power of all the DWDM input channels in the OChGroup during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSinkPrevDayLowAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.5.5.1.3
The lowest aggregated optical power of all the DWDM input channels in the OChGroup during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSinkPrevDayHighAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.5.5.1.4
The highest aggregated optical power of all the DWDM input channels in the OChGroup during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSinkPrevDayLastOutputPower 1.3.6.1.4.1.2636.3.73.1.1.5.5.1.5
The last optical power monitored at the output in the OChGroup during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSinkPrevDayLowOutputPower 1.3.6.1.4.1.2636.3.73.1.1.5.5.1.6
The lowest optical power monitored at the output in the OChGroup during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSinkPrevDayHighOutputPower 1.3.6.1.4.1.2636.3.73.1.1.5.5.1.7
The highest optical power monitored at the output in the OChGroup during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSrcCurrentTable 1.3.6.1.4.1.2636.3.73.1.1.5.6
A table of OChGroup source performance monitoring information for the current 15-minute interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfOChGroupSrcCurrentEntry

jnxoptIfOChGroupSrcCurrentEntry 1.3.6.1.4.1.2636.3.73.1.1.5.6.1
A conceptual row that contains OChGroup source performance monitoring information of an interface for the current 15-minute interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfOChGroupSrcCurrentEntry  

jnxoptIfOChGroupSrcCurrentSuspectedFlag 1.3.6.1.4.1.2636.3.73.1.1.5.6.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

jnxoptIfOChGroupSrcCurrentOutputPower 1.3.6.1.4.1.2636.3.73.1.1.5.6.1.2
The optical power monitored at the output.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSrcCurrentLowOutputPower 1.3.6.1.4.1.2636.3.73.1.1.5.6.1.3
The lowest optical power monitored at the output during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSrcCurrentHighOutputPower 1.3.6.1.4.1.2636.3.73.1.1.5.6.1.4
The highest optical power monitored at the output during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSrcCurrentLowerOutputPowerThreshold 1.3.6.1.4.1.2636.3.73.1.1.5.6.1.5
The lower limit threshold on output power. If jnxoptIfOChGroupSrcCurrentOutputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSrcCurrentUpperOutputPowerThreshold 1.3.6.1.4.1.2636.3.73.1.1.5.6.1.6
The upper limit threshold on output power. If jnxoptIfOChGroupSrcCurrentOutputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSrcCurrentAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.5.6.1.7
The aggregated optical power monitored at the input.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSrcCurrentLowAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.5.6.1.8
The lowest aggregated optical power monitored at the input during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSrcCurrentHighAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.5.6.1.9
The highest aggregated optical power monitored at the input during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSrcCurrentLowerInputPowerThreshold 1.3.6.1.4.1.2636.3.73.1.1.5.6.1.10
The lower limit threshold on input power. If jnxoptIfOChGroupSrcCurrentAggregatedInputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSrcCurrentUpperInputPowerThreshold 1.3.6.1.4.1.2636.3.73.1.1.5.6.1.11
The upper limit threshold on input power. If jnxoptIfOChGroupSrcCurrentAggregatedInputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSrcIntervalTable 1.3.6.1.4.1.2636.3.73.1.1.5.7
A table of historical OChGroup source performance monitoring information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfOChGroupSrcIntervalEntry

jnxoptIfOChGroupSrcIntervalEntry 1.3.6.1.4.1.2636.3.73.1.1.5.7.1
A conceptual row that contains OChGroup source performance monitoring information of an interface during a particular historical interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfOChGroupSrcIntervalEntry  

jnxoptIfOChGroupSrcIntervalNumber 1.3.6.1.4.1.2636.3.73.1.1.5.7.1.1
Uniquely identifies the interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfIntervalNumber  

jnxoptIfOChGroupSrcIntervalSuspectedFlag 1.3.6.1.4.1.2636.3.73.1.1.5.7.1.2
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

jnxoptIfOChGroupSrcIntervalLastOutputPower 1.3.6.1.4.1.2636.3.73.1.1.5.7.1.3
The last optical power monitored at the output during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSrcIntervalLowOutputPower 1.3.6.1.4.1.2636.3.73.1.1.5.7.1.4
The lowest optical power monitored at the output during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSrcIntervalHighOutputPower 1.3.6.1.4.1.2636.3.73.1.1.5.7.1.5
The highest optical power monitored at the output during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSrcIntervalLastAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.5.7.1.6
The last aggregated optical power monitored at the input during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSrcIntervalLowAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.5.7.1.7
The lowest aggregated optical power monitored at the input during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSrcIntervalHighAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.5.7.1.8
The highest aggregated optical power monitored at the input during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSrcCurDayTable 1.3.6.1.4.1.2636.3.73.1.1.5.8
A table of OChGroup source performance monitoring information for the current 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfOChGroupSrcCurDayEntry

jnxoptIfOChGroupSrcCurDayEntry 1.3.6.1.4.1.2636.3.73.1.1.5.8.1
A conceptual row that contains OChGroup source performance monitoring information of an interface for the current 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfOChGroupSrcCurDayEntry  

jnxoptIfOChGroupSrcCurDaySuspectedFlag 1.3.6.1.4.1.2636.3.73.1.1.5.8.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

jnxoptIfOChGroupSrcCurDayLowOutputPower 1.3.6.1.4.1.2636.3.73.1.1.5.8.1.2
The lowest optical power monitored at the output during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSrcCurDayHighOutputPower 1.3.6.1.4.1.2636.3.73.1.1.5.8.1.3
The highest optical power monitored at the output during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSrcCurDayLowAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.5.8.1.4
The lowest aggregated optical power monitored at the input during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSrcCurDayHighAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.5.8.1.5
The highest aggregated optical power monitored at the input during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSrcPrevDayTable 1.3.6.1.4.1.2636.3.73.1.1.5.9
A table of OChGroup source performance monitoring information for the previous 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfOChGroupSrcPrevDayEntry

jnxoptIfOChGroupSrcPrevDayEntry 1.3.6.1.4.1.2636.3.73.1.1.5.9.1
A conceptual row that contains OChGroup source performance monitoring information of an interface for the previous 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfOChGroupSrcPrevDayEntry  

jnxoptIfOChGroupSrcPrevDaySuspectedFlag 1.3.6.1.4.1.2636.3.73.1.1.5.9.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

jnxoptIfOChGroupSrcPrevDayLastOutputPower 1.3.6.1.4.1.2636.3.73.1.1.5.9.1.2
The last optical power monitored at the output during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSrcPrevDayLowOutputPower 1.3.6.1.4.1.2636.3.73.1.1.5.9.1.3
The lowest optical power monitored at the output during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSrcPrevDayHighOutputPower 1.3.6.1.4.1.2636.3.73.1.1.5.9.1.4
The highest optical power monitored at the output during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSrcPrevDayLastAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.5.9.1.5
The last aggregated optical power monitored at the input during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSrcPrevDayLowAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.5.9.1.6
The lowest aggregated optical power monitored at the input during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChGroupSrcPrevDayHighAggregatedInputPower 1.3.6.1.4.1.2636.3.73.1.1.5.9.1.7
The highest aggregated optical power monitored at the input during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChConfigTable 1.3.6.1.4.1.2636.3.73.1.1.6.1
A table of OCh configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfOChConfigEntry

jnxoptIfOChConfigEntry 1.3.6.1.4.1.2636.3.73.1.1.6.1.1
A conceptual row that contains OCh configuration information of an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfOChConfigEntry  

jnxoptIfOChDirectionality 1.3.6.1.4.1.2636.3.73.1.1.6.1.1.1
Indicates the directionality of the entity.
Status: current Access: read-only
OBJECT-TYPE    
  JnxoptIfDirectionality  

jnxoptIfOChCurrentStatus 1.3.6.1.4.1.2636.3.73.1.1.6.1.1.2
Indicates the defect condition of the entity, if any. This object is applicable when jnxoptIfOChDirectionality has the value sink(1) or bidirectional(3). In full-capability systems the bit position los(1) is not used. In reduced-capability systems or at IrDI interfaces only the bit positions los(1) and ssfP(3) are used.
Status: current Access: read-only
OBJECT-TYPE    
  BITS losP(0), los(1), oci(2), ssfP(3), ssfO(4), ssf(5)  

jnxoptIfOChSinkCurrentTable 1.3.6.1.4.1.2636.3.73.1.1.6.2
A table of OCh sink performance monitoring information for the current 15-minute interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfOChSinkCurrentEntry

jnxoptIfOChSinkCurrentEntry 1.3.6.1.4.1.2636.3.73.1.1.6.2.1
A conceptual row that contains OCh sink performance monitoring information for an interface for the current 15-minute interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfOChSinkCurrentEntry  

jnxoptIfOChSinkCurrentSuspectedFlag 1.3.6.1.4.1.2636.3.73.1.1.6.2.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

jnxoptIfOChSinkCurrentInputPower 1.3.6.1.4.1.2636.3.73.1.1.6.2.1.2
The optical power monitored at the input.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChSinkCurrentLowInputPower 1.3.6.1.4.1.2636.3.73.1.1.6.2.1.3
The lowest optical power monitored at the input during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChSinkCurrentHighInputPower 1.3.6.1.4.1.2636.3.73.1.1.6.2.1.4
The highest optical power monitored at the input during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChSinkCurrentLowerInputPowerThreshold 1.3.6.1.4.1.2636.3.73.1.1.6.2.1.5
The lower limit threshold on input power. If jnxoptIfOChSinkCurrentInputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

jnxoptIfOChSinkCurrentUpperInputPowerThreshold 1.3.6.1.4.1.2636.3.73.1.1.6.2.1.6
The upper limit threshold on input power. If jnxoptIfOChSinkCurrentInputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

jnxoptIfOChSinkIntervalTable 1.3.6.1.4.1.2636.3.73.1.1.6.3
A table of historical OCh sink performance monitoring information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfOChSinkIntervalEntry

jnxoptIfOChSinkIntervalEntry 1.3.6.1.4.1.2636.3.73.1.1.6.3.1
A conceptual row that contains OCh sink performance monitoring information of an interface during a particular historical interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfOChSinkIntervalEntry  

jnxoptIfOChSinkIntervalNumber 1.3.6.1.4.1.2636.3.73.1.1.6.3.1.1
Uniquely identifies the interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfIntervalNumber  

jnxoptIfOChSinkIntervalSuspectedFlag 1.3.6.1.4.1.2636.3.73.1.1.6.3.1.2
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

jnxoptIfOChSinkIntervalLastInputPower 1.3.6.1.4.1.2636.3.73.1.1.6.3.1.3
The last optical power monitored at the input during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChSinkIntervalLowInputPower 1.3.6.1.4.1.2636.3.73.1.1.6.3.1.4
The lowest optical power monitored at the input during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChSinkIntervalHighInputPower 1.3.6.1.4.1.2636.3.73.1.1.6.3.1.5
The highest optical power monitored at the input during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChSinkCurDayTable 1.3.6.1.4.1.2636.3.73.1.1.6.4
A table of OCh sink performance monitoring information for the current 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfOChSinkCurDayEntry

jnxoptIfOChSinkCurDayEntry 1.3.6.1.4.1.2636.3.73.1.1.6.4.1
A conceptual row that contains OCh sink performance monitoring information of an interface for the current 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfOChSinkCurDayEntry  

jnxoptIfOChSinkCurDaySuspectedFlag 1.3.6.1.4.1.2636.3.73.1.1.6.4.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

jnxoptIfOChSinkCurDayLowInputPower 1.3.6.1.4.1.2636.3.73.1.1.6.4.1.2
The lowest optical power monitored at the input during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChSinkCurDayHighInputPower 1.3.6.1.4.1.2636.3.73.1.1.6.4.1.3
The highest optical power monitored at the input during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChSinkPrevDayTable 1.3.6.1.4.1.2636.3.73.1.1.6.5
A table of OCh sink performance monitoring information for the previous 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfOChSinkPrevDayEntry

jnxoptIfOChSinkPrevDayEntry 1.3.6.1.4.1.2636.3.73.1.1.6.5.1
A conceptual row that contains OCh sink performance monitoring information of an interface for the previous 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfOChSinkPrevDayEntry  

jnxoptIfOChSinkPrevDaySuspectedFlag 1.3.6.1.4.1.2636.3.73.1.1.6.5.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

jnxoptIfOChSinkPrevDayLastInputPower 1.3.6.1.4.1.2636.3.73.1.1.6.5.1.2
The last optical power monitored at the input during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChSinkPrevDayLowInputPower 1.3.6.1.4.1.2636.3.73.1.1.6.5.1.3
The lowest optical power monitored at the input during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChSinkPrevDayHighInputPower 1.3.6.1.4.1.2636.3.73.1.1.6.5.1.4
The highest optical power monitored at the input during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChSrcCurrentTable 1.3.6.1.4.1.2636.3.73.1.1.6.6
A table of OCh source performance monitoring information for the current 15-minute interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfOChSrcCurrentEntry

jnxoptIfOChSrcCurrentEntry 1.3.6.1.4.1.2636.3.73.1.1.6.6.1
A conceptual row that contains OCh source performance monitoring information of an interface for the current 15-minute interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfOChSrcCurrentEntry  

jnxoptIfOChSrcCurrentSuspectedFlag 1.3.6.1.4.1.2636.3.73.1.1.6.6.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

jnxoptIfOChSrcCurrentOutputPower 1.3.6.1.4.1.2636.3.73.1.1.6.6.1.2
The optical power monitored at the output.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChSrcCurrentLowOutputPower 1.3.6.1.4.1.2636.3.73.1.1.6.6.1.3
The lowest optical power monitored at the output during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChSrcCurrentHighOutputPower 1.3.6.1.4.1.2636.3.73.1.1.6.6.1.4
The highest optical power monitored at the output during the current 15-minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChSrcCurrentLowerOutputPowerThreshold 1.3.6.1.4.1.2636.3.73.1.1.6.6.1.5
The lower limit threshold on output power. If jnxoptIfOChSrcCurrentOutputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

jnxoptIfOChSrcCurrentUpperOutputPowerThreshold 1.3.6.1.4.1.2636.3.73.1.1.6.6.1.6
The upper limit threshold on output power. If jnxoptIfOChSrcCurrentOutputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

jnxoptIfOChSrcIntervalTable 1.3.6.1.4.1.2636.3.73.1.1.6.7
A table of historical OCh source performance monitoring information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfOChSrcIntervalEntry

jnxoptIfOChSrcIntervalEntry 1.3.6.1.4.1.2636.3.73.1.1.6.7.1
A conceptual row that contains OCh source performance monitoring information of an interface during a particular historical interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfOChSrcIntervalEntry  

jnxoptIfOChSrcIntervalNumber 1.3.6.1.4.1.2636.3.73.1.1.6.7.1.1
Uniquely identifies the interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfIntervalNumber  

jnxoptIfOChSrcIntervalSuspectedFlag 1.3.6.1.4.1.2636.3.73.1.1.6.7.1.2
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

jnxoptIfOChSrcIntervalLastOutputPower 1.3.6.1.4.1.2636.3.73.1.1.6.7.1.3
The last optical power monitored at the output during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChSrcIntervalLowOutputPower 1.3.6.1.4.1.2636.3.73.1.1.6.7.1.4
The lowest optical power monitored at the output during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChSrcIntervalHighOutputPower 1.3.6.1.4.1.2636.3.73.1.1.6.7.1.5
The highest optical power monitored at the output during the interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChSrcCurDayTable 1.3.6.1.4.1.2636.3.73.1.1.6.8
A table of OCh source performance monitoring information for the current 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfOChSrcCurDayEntry

jnxoptIfOChSrcCurDayEntry 1.3.6.1.4.1.2636.3.73.1.1.6.8.1
A conceptual row that contains OCh source performance monitoring information of an interface for the current 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfOChSrcCurDayEntry  

jnxoptIfOChSrcCurDaySuspectedFlag 1.3.6.1.4.1.2636.3.73.1.1.6.8.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

jnxoptIfOChSrcCurDayLowOutputPower 1.3.6.1.4.1.2636.3.73.1.1.6.8.1.2
The lowest optical power monitored at the output during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChSrcCurDayHighOutputPower 1.3.6.1.4.1.2636.3.73.1.1.6.8.1.3
The highest optical power monitored at the output during the current 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChSrcPrevDayTable 1.3.6.1.4.1.2636.3.73.1.1.6.9
A table of OCh source performance monitoring information for the previous 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfOChSrcPrevDayEntry

jnxoptIfOChSrcPrevDayEntry 1.3.6.1.4.1.2636.3.73.1.1.6.9.1
A conceptual row that contains OCh source performance monitoring information of an interface for the previous 24-hour interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfOChSrcPrevDayEntry  

jnxoptIfOChSrcPrevDaySuspectedFlag 1.3.6.1.4.1.2636.3.73.1.1.6.9.1.1
If true, the data in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

jnxoptIfOChSrcPrevDayLastOutputPower 1.3.6.1.4.1.2636.3.73.1.1.6.9.1.2
The last optical power monitored at the output during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChSrcPrevDayLowOutputPower 1.3.6.1.4.1.2636.3.73.1.1.6.9.1.3
The lowest optical power monitored at the output during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOChSrcPrevDayHighOutputPower 1.3.6.1.4.1.2636.3.73.1.1.6.9.1.4
The highest optical power monitored at the output during the previous 24-hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

jnxoptIfOTUkConfigTable 1.3.6.1.4.1.2636.3.73.1.1.7.1
A table of OTUk configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfOTUkConfigEntry

jnxoptIfOTUkConfigEntry 1.3.6.1.4.1.2636.3.73.1.1.7.1.1
A conceptual row that contains OTUk configuration information of an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfOTUkConfigEntry  

jnxoptIfOTUkDirectionality 1.3.6.1.4.1.2636.3.73.1.1.7.1.1.1
Indicates the directionality of the entity.
Status: current Access: read-only
OBJECT-TYPE    
  JnxoptIfDirectionality  

jnxoptIfOTUkBitRateK 1.3.6.1.4.1.2636.3.73.1.1.7.1.1.2
Indicates the bit rate of the entity.
Status: current Access: read-only
OBJECT-TYPE    
  JnxoptIfBitRateK  

jnxoptIfOTUkTraceIdentifierTransmitted 1.3.6.1.4.1.2636.3.73.1.1.7.1.1.3
The trace identifier transmitted. This object is applicable when jnxoptIfOTUkDirectionality has the value source(2) or bidirectional(3). It must not be instantiated in rows where jnxoptIfOTUkDirectionality has the value sink(1). If no value is ever set by a management entity for this object, system-specific default value will be used. Any implementation that instantiates this object must document the system-specific default value or how it is derived.
Status: current Access: read-write
OBJECT-TYPE    
  JnxoptIfTxTI  

jnxoptIfOTUkDAPIExpected 1.3.6.1.4.1.2636.3.73.1.1.7.1.1.4
The DAPI expected by the receiver. This object is only applicable to the sink function, i.e., only when jnxoptIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where jnxoptIfOTUkDirectionality has the value source(2). This object has no effect when jnxoptIfOTUkTIMDetMode has the value off(1).
Status: current Access: read-write
OBJECT-TYPE    
  JnxoptIfExDAPI  

jnxoptIfOTUkSAPIExpected 1.3.6.1.4.1.2636.3.73.1.1.7.1.1.5
The SAPI expected by the receiver. This object is only applicable to the sink function, i.e., only when jnxoptIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where jnxoptIfOTUkDirectionality has the value source(2). This object has no effect when jnxoptIfOTUkTIMDetMode has the value off(1).
Status: current Access: read-write
OBJECT-TYPE    
  JnxoptIfExSAPI  

jnxoptIfOTUkTraceIdentifierAccepted 1.3.6.1.4.1.2636.3.73.1.1.7.1.1.6
The actual trace identifier accepted. This object is only applicable to the sink function, i.e., only when jnxoptIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where jnxoptIfOTUkDirectionality has the value source(2). The value of this object is unspecified when jnxoptIfOTUkCurrentStatus indicates a near-end defect (i.e., ssf(3), lof(4), ais(5), lom(6)) that prevents extraction of the trace message.
Status: current Access: read-only
OBJECT-TYPE    
  JnxoptIfAcTI  

jnxoptIfOTUkTIMDetMode 1.3.6.1.4.1.2636.3.73.1.1.7.1.1.7
Indicates the mode of the Trace Identifier Mismatch (TIM) Detection function. This object is only applicable to the sink function, i.e., only when jnxoptIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where jnxoptIfOTUkDirectionality has the value source(2). The default value of this object is off(1).
Status: current Access: read-write
OBJECT-TYPE    
  JnxoptIfTIMDetMode  

jnxoptIfOTUkTIMActEnabled 1.3.6.1.4.1.2636.3.73.1.1.7.1.1.8
Indicates whether the Trace Identifier Mismatch (TIM) Consequent Action function is enabled. This object is only applicable to the sink function, i.e., only when jnxoptIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where jnxoptIfOTUkDirectionality has the value source(2). This object has no effect when jnxoptIfOTUkTIMDetMode has the value off(1). The default value of this object is false(2).
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxoptIfOTUkDEGThr 1.3.6.1.4.1.2636.3.73.1.1.7.1.1.9
Indicates the threshold level for declaring a performance monitoring (PM) Second to be bad. A PM Second is declared bad if the percentage of detected errored blocks in that second is greater than or equal to jnxoptIfOTUkDEGThr. This object is only applicable to the sink function, i.e., only when jnxoptIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where jnxoptIfOTUkDirectionality has the value source(2). The default value of this object is Severely Errored Second (SES) Estimator (See ITU-T G.7710).
Status: current Access: read-write
OBJECT-TYPE    
  JnxoptIfDEGThr  

jnxoptIfOTUkDEGM 1.3.6.1.4.1.2636.3.73.1.1.7.1.1.10
Indicates the threshold level for declaring a Degraded Signal defect (dDEG). A dDEG shall be declared if jnxoptIfOTUkDEGM consecutive bad PM Seconds are detected. This object is only applicable to the sink function, i.e., only when jnxoptIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where jnxoptIfOTUkDirectionality has the value source(2). The default value of this object is 7 (See ITU-T G.7710).
Status: current Access: read-write
OBJECT-TYPE    
  JnxoptIfDEGM  

jnxoptIfOTUkSinkAdaptActive 1.3.6.1.4.1.2636.3.73.1.1.7.1.1.11
Indicates whether the sink adaptation function is activated or not. This object is only applicable to the sink function, i.e., only when jnxoptIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where jnxoptIfOTUkDirectionality has the value source(2). The default value of this object is false(2).
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxoptIfOTUkSourceAdaptActive 1.3.6.1.4.1.2636.3.73.1.1.7.1.1.12
Indicates whether the source adaptation function is activated or not. This object is only applicable to the source function, i.e., only when jnxoptIfOTUkDirectionality has the value source(2) or bidirectional(3). It must not be instantiated in rows where jnxoptIfOTUkDirectionality has the value sink(1). The default value of this object is false(2).
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxoptIfOTUkSinkFECEnabled 1.3.6.1.4.1.2636.3.73.1.1.7.1.1.13
If Forward Error Correction (FEC) is supported, this object indicates whether FEC at the OTUk sink adaptation function is enabled or not. This object is only applicable to the sink function, i.e., only when jnxoptIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where jnxoptIfOTUkDirectionality has the value source(2). The default value of this object is true(1).
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxoptIfOTUkCurrentStatus 1.3.6.1.4.1.2636.3.73.1.1.7.1.1.14
Indicates the defect condition of the entity, if any. This object is only applicable to the sink function, i.e., only when jnxoptIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where jnxoptIfOTUkDirectionality has the value source(2).
Status: current Access: read-only
OBJECT-TYPE    
  BITS tim(0), deg(1), bdi(2), ssf(3), lof(4), ais(5), lom(6)  

jnxoptIfGCC0ConfigTable 1.3.6.1.4.1.2636.3.73.1.1.7.2
A table of GCC0 configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfGCC0ConfigEntry

jnxoptIfGCC0ConfigEntry 1.3.6.1.4.1.2636.3.73.1.1.7.2.1
A conceptual row that contains GCC0 configuration information of an interface. Each instance must correspond to an instance of jnxoptIfOTUkConfigEntry. Separate source and/or sink instances may exist for a given ifIndex value, or a single bidirectional instance may exist, but a bidirectional instance may not coexist with a source or sink instance. Instances of this conceptual row persist across agent restarts.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfGCC0ConfigEntry  

jnxoptIfGCC0Directionality 1.3.6.1.4.1.2636.3.73.1.1.7.2.1.1
Indicates the directionality of the entity. The values source(2) and bidirectional(3) are not allowed if the corresponding instance of jnxoptIfOTUkDirectionality has the value sink(1). The values sink(1) and bidirectional(3) are not allowed if the corresponding instance of jnxoptIfOTUkDirectionality has the value source(2).
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfDirectionality  

jnxoptIfGCC0Application 1.3.6.1.4.1.2636.3.73.1.1.7.2.1.2
Indicates the application transported by the GCC0 entity. Example applications are ECC, User data channel. The value of this object may not be changed when jnxoptIfGCC0RowStatus has the value active(1).
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

jnxoptIfGCC0RowStatus 1.3.6.1.4.1.2636.3.73.1.1.7.2.1.3
This columnar object is used for creating and deleting a conceptual row of the jnxoptIfGCC0 config table. It is used to model the addGCC0Access and removeGCC0Access operations of an OTUk_TTP for GCC0 access control as defined in G.874.1. Setting RowStatus to createAndGo or createAndWait implies addGCC0Access. Setting RowStatus to destroy implies removeGCC0Access.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

jnxoptIfODUkConfigTable 1.3.6.1.4.1.2636.3.73.1.1.8.1
A table of ODUk configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfODUkConfigEntry

jnxoptIfODUkConfigEntry 1.3.6.1.4.1.2636.3.73.1.1.8.1.1
A conceptual row that contains ODUk configuration information of an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfODUkConfigEntry  

jnxoptIfODUkDirectionality 1.3.6.1.4.1.2636.3.73.1.1.8.1.1.1
Indicates the directionality of the entity.
Status: current Access: read-only
OBJECT-TYPE    
  JnxoptIfDirectionality  

jnxoptIfODUkBitRateK 1.3.6.1.4.1.2636.3.73.1.1.8.1.1.2
Indicates the bit rate of the entity.
Status: current Access: read-only
OBJECT-TYPE    
  JnxoptIfBitRateK  

jnxoptIfODUkTcmFieldsInUse 1.3.6.1.4.1.2636.3.73.1.1.8.1.1.3
Indicates the TCM field(s) that are currently in use. The positions of the bits correspond to the TCM fields. A bit that is set to 1 means that the corresponding TCM field is used. This object will be updated when rows are created in or deleted from the jnxoptIfODUkTConfigTable, or the jnxoptIfODUkTNimConfigTable.
Status: current Access: read-only
OBJECT-TYPE    
  BITS tcmField1(0), tcmField2(1), tcmField3(2), tcmField4(3), tcmField5(4), tcmField6(5)  

jnxoptIfODUkPositionSeqCurrentSize 1.3.6.1.4.1.2636.3.73.1.1.8.1.1.4
This variable indicates the current size of the position sequence (i.e., number of TCM function and/or GCC12 access that have been created in the ODUk interface). When the value of this variable is greater than zero, it means that one or more TCM function and/or GCC12 access have been created in the ODUk interface. In this case, there will be as many rows in the jnxoptIfODUkPositionSeqTable as the value of jnxoptIfODUkPositionSeqCurrentSize corresponding to this ODUk interface, one row for each TCM function or GCC12 access. The position of the TCM function and/or GCC12 access within the sequence is indicated by the jnxoptIfODUkPositionSeqPosition variable in jnxoptIfODUkPositionSeqTable. The jnxoptIfODUkPositionSeqTable also provides pointers to the corresponding TCM function (jnxoptIfODUkT) and GCC12 access (jnxoptIfGCC12) entities.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxoptIfODUkTtpPresent 1.3.6.1.4.1.2636.3.73.1.1.8.1.1.5
This object has the value true(1) if the ifEntry under which it is instantiated contains an ODUk Trail Termination Point, i.e., is the endpoint of an ODUk path. In that case there will be a corresponding row in the ODUk TTP config table and it will not be possible to create corresponding rows in the ODUk NIM config table. This object has the value false(2) if the ifEntry under which it is instantiated contains an intermediate ODUk Connection Termination Point. In that case there is no corresponding row in the ODUk TTP config table, but it will be possible to create corresponding rows in the ODUk NIM config table. This object also affects the allowable options in rows created in the GCC12 config table and in the ODUkT config table, as specified in the DESCRIPTION clauses of the columns in those tables.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

jnxoptIfODUkTtpConfigTable 1.3.6.1.4.1.2636.3.73.1.1.8.2
A table of ODUk TTP configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfODUkTtpConfigEntry

jnxoptIfODUkTtpConfigEntry 1.3.6.1.4.1.2636.3.73.1.1.8.2.1
A conceptual row that contains ODUk TTP configuration information of an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfODUkTtpConfigEntry  

jnxoptIfODUkTtpTraceIdentifierTransmitted 1.3.6.1.4.1.2636.3.73.1.1.8.2.1.1
The trace identifier transmitted. This object is applicable when jnxoptIfODUkDirectionality has the value source(2) or bidirectional(3). It must not be instantiated in rows where jnxoptIfODUkDirectionality has the value sink(1). If no value is ever set by a management entity for this object, system-specific default value will be used. Any implementation that instantiates this object must document the system-specific default value or how it is derived.
Status: current Access: read-write
OBJECT-TYPE    
  JnxoptIfTxTI  

jnxoptIfODUkTtpDAPIExpected 1.3.6.1.4.1.2636.3.73.1.1.8.2.1.2
The DAPI expected by the receiver. This object is only applicable to the sink function, i.e., only when jnxoptIfODUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where jnxoptIfODUkDirectionality has the value source(2). This object has no effect when jnxoptIfODUkTtpTIMDetMode has the value off(1).
Status: current Access: read-write
OBJECT-TYPE    
  JnxoptIfExDAPI  

jnxoptIfODUkTtpSAPIExpected 1.3.6.1.4.1.2636.3.73.1.1.8.2.1.3
The SAPI expected by the receiver. This object is only applicable to the sink function, i.e., only when jnxoptIfODUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where jnxoptIfODUkDirectionality has the value source(2). This object has no effect when jnxoptIfODUkTtpTIMDetMode has the value off(1).
Status: current Access: read-write
OBJECT-TYPE    
  JnxoptIfExSAPI  

jnxoptIfODUkTtpTraceIdentifierAccepted 1.3.6.1.4.1.2636.3.73.1.1.8.2.1.4
The actual trace identifier accepted. This object is only applicable to the sink function, i.e., only when jnxoptIfODUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where jnxoptIfODUkDirectionality has the value source(2). The value of this object is unspecified when jnxoptIfODUkTtpCurrentStatus indicates a near-end defect (i.e., oci(0), lck(1), ssf(5)) that prevents extraction of the trace message.
Status: current Access: read-only
OBJECT-TYPE    
  JnxoptIfAcTI  

jnxoptIfODUkTtpTIMDetMode 1.3.6.1.4.1.2636.3.73.1.1.8.2.1.5
Indicates the mode of the Trace Identifier Mismatch (TIM) Detection function. This object is only applicable to the sink function, i.e., only when jnxoptIfODUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where jnxoptIfODUkDirectionality has the value source(2). The default value of this object is off(1).
Status: current Access: read-write
OBJECT-TYPE    
  JnxoptIfTIMDetMode  

jnxoptIfODUkTtpTIMActEnabled 1.3.6.1.4.1.2636.3.73.1.1.8.2.1.6
Indicates whether the Trace Identifier Mismatch (TIM) Consequent Action function is enabled. This object is only applicable to the sink function, i.e., only when jnxoptIfODUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where jnxoptIfODUkDirectionality has the value source(2). This object has no effect when jnxoptIfODUkTtpTIMDetMode has the value off(1). The default value of this object is false(2).
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

jnxoptIfODUkTtpDEGThr 1.3.6.1.4.1.2636.3.73.1.1.8.2.1.7
Indicates the threshold level for declaring a performance monitoring (PM) Second to be bad. A PM Second is declared bad if the percentage of detected errored blocks in that second is greater than or equal to jnxoptIfODUkDEGThr. This object is only applicable to the sink function, i.e., only when jnxoptIfODUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where jnxoptIfODUkDirectionality has the value source(2). The default value of this object is Severely Errored Second (SES) Estimator (See ITU-T G.7710).
Status: current Access: read-write
OBJECT-TYPE    
  JnxoptIfDEGThr  

jnxoptIfODUkTtpDEGM 1.3.6.1.4.1.2636.3.73.1.1.8.2.1.8
Indicates the threshold level for declaring a Degraded Signal defect (dDEG). A dDEG shall be declared if jnxoptIfODUkDEGM consecutive bad PM Seconds are detected. This object is only applicable to the sink function, i.e., only when jnxoptIfODUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where jnxoptIfODUkDirectionality has the value source(2). The default value of this object is 7 (See ITU-T G.7710).
Status: current Access: read-write
OBJECT-TYPE    
  JnxoptIfDEGM  

jnxoptIfODUkTtpCurrentStatus 1.3.6.1.4.1.2636.3.73.1.1.8.2.1.9
Indicates the defect condition of the entity, if any. This object is only applicable to the sink function, i.e., only when jnxoptIfODUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where jnxoptIfODUkDirectionality has the value source(2).
Status: current Access: read-only
OBJECT-TYPE    
  BITS oci(0), lck(1), tim(2), deg(3), bdi(4), ssf(5)  

jnxoptIfODUkPositionSeqTable 1.3.6.1.4.1.2636.3.73.1.1.8.3
A table of ODUk Position Sequence information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfODUkPositionSeqEntry

jnxoptIfODUkPositionSeqEntry 1.3.6.1.4.1.2636.3.73.1.1.8.3.1
A conceptual row that contains ODUk position sequence information of an ODUk interface. The ODUk interface is identified by the ifIndex. Associated with each ODUk interface there may be one of more conceptual rows in the jnxoptIfODUkPositionSeqTable. Each row represents a TCM or GCC12 access function within the associated ODUk interface. Rows of the jnxoptIfODUkPositionSeqTable table are created/deleted as the result of the creation/deletion of the jnxoptIfODUkT or jnxoptIfGCC12 entities.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfODUkPositionSeqEntry  

jnxoptIfODUkPositionSeqIndex 1.3.6.1.4.1.2636.3.73.1.1.8.3.1.1
This variable identifies a row in the jnxoptIfODUkPositionSeqTable Table. Each row of the jnxoptIfODUkPositionSeqTable Table represents a TCM or GCC12 access function within the associated ODUk interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..4294967295  

jnxoptIfODUkPositionSeqPosition 1.3.6.1.4.1.2636.3.73.1.1.8.3.1.2
This variable indicates the position of the TCM or GCC12 access function within the sequence of TCMs & GCC12 access functions of the associated ODUk interface. The TCM or GCC12 presented by this row is referenced by the jnxoptIfODUkPositionSeqPointer variable.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

jnxoptIfODUkPositionSeqPointer 1.3.6.1.4.1.2636.3.73.1.1.8.3.1.3
This variable identifies the TCM or GCC12 access function by pointing to the corresponding jnxoptIfODUkT or jnxoptIfGCC12 entity.
Status: current Access: read-only
OBJECT-TYPE    
  RowPointer  

jnxoptIfODUkNimConfigTable 1.3.6.1.4.1.2636.3.73.1.1.8.4
A table of ODUkNim configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfODUkNimConfigEntry

jnxoptIfODUkNimConfigEntry 1.3.6.1.4.1.2636.3.73.1.1.8.4.1
A conceptual row that contains ODUkNim configuration information of an interface. Each instance must correspond to an instance of jnxoptIfODUkConfigEntry for which jnxoptIfODUkTtpPresent has the value false(2). Instances of this conceptual row persist across agent restarts, and read-create columns other than the status column may be modified while the row is active.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfODUkNimConfigEntry  

jnxoptIfODUkNimDirectionality 1.3.6.1.4.1.2636.3.73.1.1.8.4.1.1
Specifies the monitor point for the ODUk Path non-intrusive monitoring function. The value source(2) is not allowed if the corresponding instance of jnxoptIfODUkDirectionality has the value sink(1), and the value sink(1) is not allowed if the corresponding instance of jnxoptIfODUkDirectionality has the value source(2). Either the value sink(1) or source(2) is allowed if the corresponding instance of jnxoptIfODUkDirectionality has the value bidirectional(3). The value sink(1) means monitoring at the sink direction path signal of the ODUk CTP. The value source(2) means monitoring at the source direction path signal of the ODUk CTP. Monitoring the source direction of an ODUk CTP is necessary in those cases where the ODUk CTP is at an SNCP (Subnetwork Connection Protection) end (e.g., see Figure I.1.2/G.874.1). If one would like to get the performance of the protected connection, one cannot use the NIM function at both ODUk CTP sinks (before the matrix), instead one should monitor the signal at the source ODUk CTP after the matrix.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfSinkOrSource  

jnxoptIfODUkNimDAPIExpected 1.3.6.1.4.1.2636.3.73.1.1.8.4.1.2
The DAPI expected by the receiver. This object has no effect if jnxoptIfODUkNimTIMDetMode has the value off(1) or sapi(3).
Status: current Access: read-create
OBJECT-TYPE    
  JnxoptIfExDAPI  

jnxoptIfODUkNimSAPIExpected 1.3.6.1.4.1.2636.3.73.1.1.8.4.1.3
The SAPI expected by the receiver. This object has no effect if jnxoptIfODUkNimTIMDetMode has the value off(1) or dapi(2).
Status: current Access: read-create
OBJECT-TYPE    
  JnxoptIfExSAPI  

jnxoptIfODUkNimTraceIdentifierAccepted 1.3.6.1.4.1.2636.3.73.1.1.8.4.1.4
The actual trace identifier accepted. The value of this object is unspecified if jnxoptIfODUkNimCurrentStatus has any of the bit positions oci(0), lck(1), or ssf(5) set or if jnxoptIfODUkNimRowStatus has any value other than active(1).
Status: current Access: read-only
OBJECT-TYPE    
  JnxoptIfAcTI  

jnxoptIfODUkNimTIMDetMode 1.3.6.1.4.1.2636.3.73.1.1.8.4.1.5
Indicates the mode of the Trace Identifier Mismatch (TIM) Detection function.
Status: current Access: read-create
OBJECT-TYPE    
  JnxoptIfTIMDetMode  

jnxoptIfODUkNimTIMActEnabled 1.3.6.1.4.1.2636.3.73.1.1.8.4.1.6
Indicates whether the Trace Identifier Mismatch (TIM) Consequent Action function is enabled.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

jnxoptIfODUkNimDEGThr 1.3.6.1.4.1.2636.3.73.1.1.8.4.1.7
Indicates the threshold level for declaring a performance monitoring (PM) Second to be bad. A PM Second is declared bad if the percentage of detected errored blocks in that second is greater than or equal to jnxoptIfODUkNimDEGThr.
Status: current Access: read-create
OBJECT-TYPE    
  JnxoptIfDEGThr  

jnxoptIfODUkNimDEGM 1.3.6.1.4.1.2636.3.73.1.1.8.4.1.8
Indicates the threshold level for declaring a Degraded Signal defect (dDEG). A dDEG shall be declared if jnxoptIfODUkNimDEGM consecutive bad PM Seconds are detected.
Status: current Access: read-create
OBJECT-TYPE    
  JnxoptIfDEGM  

jnxoptIfODUkNimCurrentStatus 1.3.6.1.4.1.2636.3.73.1.1.8.4.1.9
Indicates the defect condition of the entity, if any. The value of this object is unspecified if jnxoptIfODUkNimRowStatus has any value other than active(1).
Status: current Access: read-only
OBJECT-TYPE    
  BITS oci(0), lck(1), tim(2), deg(3), bdi(4), ssf(5)  

jnxoptIfODUkNimRowStatus 1.3.6.1.4.1.2636.3.73.1.1.8.4.1.10
This columnar object is used for creating and deleting a conceptual row of the jnxoptIfODUkNim config table. It is used to model the activateNim and deactivateNim operations of an OTUk_CTP for non-intrusive monitoring control as defined in G.874.1. Setting RowStatus to createAndGo or createAndWait implies activateNim. Setting RowStatus to destroy implies deactivateNim.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

jnxoptIfGCC12ConfigTable 1.3.6.1.4.1.2636.3.73.1.1.8.5
A table of GCC12 configuration information. The GCC function processes the GCC overhead bytes passing through them but leave the remainder of the ODUk overhead and payload data alone.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfGCC12ConfigEntry

jnxoptIfGCC12ConfigEntry 1.3.6.1.4.1.2636.3.73.1.1.8.5.1
A conceptual row that contains GCC12 configuration information of an interface. Each instance must correspond to an instance of jnxoptIfODUkConfigEntry. Separate instances providing GCC1-only access and GCC2-only access may exist for a given ifIndex value, or a single instance providing GCC1 + GCC2 may exist, but a GCC1 + GCC2 instance may not coexist with a GCC1-only or GCC2-only instance. Instances of this conceptual row persist across agent restarts.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfGCC12ConfigEntry  

jnxoptIfGCC12Codirectional 1.3.6.1.4.1.2636.3.73.1.1.8.5.1.1
Indicates the directionality of the GCC12 termination with respect to the associated ODUk CTP. The value true(1) means that the sink part of the GCC12 extracts COMMS data from the signal at the input to the ODUk CTP sink and the source part of the GCC12 inserts COMMS data into the signal at the output of the ODUk CTP source. The value false(2) means that the sink part of the GCC12 extracts COMMS data from the signal at the output of the ODUk CTP source and the source part of the GCC12 inserts COMMS data into the signal at the input of the ODUk CTP sink. This attribute may assume either value when the corresponding instance of jnxoptIfODUkTtpPresent has the value false(2). When the value of the corresponding instance of jnxoptIfODUkTtpPresent is true(1) then the only value allowed for this attribute is true(1).
Status: current Access: not-accessible
OBJECT-TYPE    
  TruthValue  

jnxoptIfGCC12GCCAccess 1.3.6.1.4.1.2636.3.73.1.1.8.5.1.2
Indicates the GCC access represented by the entity.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER gcc1(1), gcc2(2), gcc1and2(3)  

jnxoptIfGCC12GCCPassThrough 1.3.6.1.4.1.2636.3.73.1.1.8.5.1.3
Controls whether the selected GCC overhead bytes are passed through or modified. The value true(1) means that the selected GCC overhead bytes are passed through unmodified from the ODUk CTP input to the ODUk CTP output. The value false(2) means that the selected GCC overhead bytes are set to zero at the ODUk CTP output after the extraction of the COMMS data. This object has no effect if the corresponding instance of jnxoptIfODUkTtpPresent has the value true(1). The value of this object may not be changed when jnxoptIfGCC12RowStatus has the value active(1).
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

jnxoptIfGCC12Application 1.3.6.1.4.1.2636.3.73.1.1.8.5.1.4
Indicates the application transported by the GCC12 entity. Example applications are ECC, User data channel. The value of this object may not be changed when jnxoptIfGCC12RowStatus has the value active(1).
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

jnxoptIfGCC12RowStatus 1.3.6.1.4.1.2636.3.73.1.1.8.5.1.5
This columnar object is used for creating and deleting a conceptual row of the jnxoptIfGCC12 config table. It is used to model the addGCC12Access and removeGCC12Access operations of an ODUk_CTP or ODUk_TTP for GCC12 access control as defined in G.874.1. Setting RowStatus to createAndGo or createAndWait implies addGCC12Access. Setting RowStatus to destroy implies removeGCC12Access. Successful addition/removal of the GCC12 access function will result in updating the jnxoptIfODUkPositionSeqCurrentSize variable and the jnxoptIfODUkPositionSeqTable table of the associated ODUk entry in the jnxoptIfODUkConfigTable.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

jnxoptIfODUkTConfigTable 1.3.6.1.4.1.2636.3.73.1.1.9.1
A table of ODUkT configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfODUkTConfigEntry

jnxoptIfODUkTConfigEntry 1.3.6.1.4.1.2636.3.73.1.1.9.1.1
A conceptual row that contains ODUkT configuration information of an interface. Each instance must correspond to an instance of jnxoptIfODUkConfigEntry. Rows in this table are mutually exclusive with rows in the ODUkT NIM config table -- in other words, this row object may not be instantiated for a given pair of ifIndex and TCM field values if a corresponding instance of jnxoptIfODUkTNimConfigEntry already exists. Instances of this conceptual row persist across agent restarts. Except where noted otherwise, read-create columns other than the status column may be modified while the row is active.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfODUkTConfigEntry  

jnxoptIfODUkTTcmField 1.3.6.1.4.1.2636.3.73.1.1.9.1.1.1
Indicates the tandem connection monitoring field of the ODUk OH. Valid values are integers from 1 to 6.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..6  

jnxoptIfODUkTCodirectional 1.3.6.1.4.1.2636.3.73.1.1.9.1.1.2
Indicates the directionality of the ODUkT termination point with respect to the associated ODUk CTP. The value true(1) means that the sink part of the ODUkT TP extracts TCM data from the signal at the input to the ODUk CTP sink and the source part of the ODUkT TP inserts TCM data into the signal at the output of the ODUk CTP source. The value false(2) means that the sink part of the ODUkT TP extracts TCM data from the signal at the output of the ODUk CTP source and the source part of the ODUkT TP inserts TCM data into the signal at the input of the ODUk CTP sink. This attribute may assume either value when the corresponding instance of jnxoptIfODUkTtpPresent has the value false(2). When the value of the corresponding instance of jnxoptIfODUkTtpPresent is true(1) then the only value allowed for this attribute is true(1).
Status: current Access: not-accessible
OBJECT-TYPE    
  TruthValue  

jnxoptIfODUkTTraceIdentifierTransmitted 1.3.6.1.4.1.2636.3.73.1.1.9.1.1.3
The trace identifier transmitted. This object is applicable only to the following three cases. (i) jnxoptIfODUkDirectionality has the value bidirectional(3), or (ii) jnxoptIfODUkDirectionality has the value sink(1) and jnxoptIfODUkTCodirectional has the value false(2), or (iii) jnxoptIfODUkDirectionality has the value source(3) and jnxoptIfODUkTCodirectional has the value true(1). It must not be instantiated in rows for all other cases.
Status: current Access: read-create
OBJECT-TYPE    
  JnxoptIfTxTI  

jnxoptIfODUkTDAPIExpected 1.3.6.1.4.1.2636.3.73.1.1.9.1.1.4
The DAPI expected by the receiver. This object is applicable only to the following three cases. (i) jnxoptIfODUkDirectionality has the value bidirectional(3), or (ii) jnxoptIfODUkDirectionality has the value sink(1) and jnxoptIfODUkTCodirectional has the value true(1), or (iii) jnxoptIfODUkDirectionality has the value source(3) and jnxoptIfODUkTCodirectional has the value false(2). It must not be instantiated in rows for all other cases. This object has no effect when jnxoptIfODUkTTIMDetMode has the value off(1).
Status: current Access: read-create
OBJECT-TYPE    
  JnxoptIfExDAPI  

jnxoptIfODUkTSAPIExpected 1.3.6.1.4.1.2636.3.73.1.1.9.1.1.5
The SAPI expected by the receiver. This object is applicable only to the following three cases. (i) jnxoptIfODUkDirectionality has the value bidirectional(3), or (ii) jnxoptIfODUkDirectionality has the value sink(1) and jnxoptIfODUkTCodirectional has the value true(1), or (iii) jnxoptIfODUkDirectionality has the value source(3) and jnxoptIfODUkTCodirectional has the value false(2). It must not be instantiated in rows for all other cases. This object has no effect when jnxoptIfODUkTTIMDetMode has the value off(1).
Status: current Access: read-create
OBJECT-TYPE    
  JnxoptIfExSAPI  

jnxoptIfODUkTTraceIdentifierAccepted 1.3.6.1.4.1.2636.3.73.1.1.9.1.1.6
The actual trace identifier accepted. This object is applicable only to the following three cases. (i) jnxoptIfODUkDirectionality has the value bidirectional(3), or (ii) jnxoptIfODUkDirectionality has the value sink(1) and jnxoptIfODUkTCodirectional has the value true(1), or (iii) jnxoptIfODUkDirectionality has the value source(3) and jnxoptIfODUkTCodirectional has the value false(2). It must not be instantiated in rows for all other cases. The value of this object is unspecified when jnxoptIfODUkTCurrentStatus indicates a near-end defect (i.e., oci(0), lck(1), ssf(5)) that prevents extraction of the trace message.
Status: current Access: read-only
OBJECT-TYPE    
  JnxoptIfAcTI  

jnxoptIfODUkTTIMDetMode 1.3.6.1.4.1.2636.3.73.1.1.9.1.1.7
Indicates the mode of the Trace Identifier Mismatch (TIM) Detection function. This object is applicable only to the following three cases. (i) jnxoptIfODUkDirectionality has the value bidirectional(3), or (ii) jnxoptIfODUkDirectionality has the value sink(1) and jnxoptIfODUkTCodirectional has the value true(1), or (iii) jnxoptIfODUkDirectionality has the value source(3) and jnxoptIfODUkTCodirectional has the value false(2). It must not be instantiated in rows for all other cases. The default value of this object is off(1).
Status: current Access: read-create
OBJECT-TYPE    
  JnxoptIfTIMDetMode  

jnxoptIfODUkTTIMActEnabled 1.3.6.1.4.1.2636.3.73.1.1.9.1.1.8
Indicates whether the Trace Identifier Mismatch (TIM) Consequent Action function is enabled. This object is applicable only to the following three cases. (i) jnxoptIfODUkDirectionality has the value bidirectional(3), or (ii) jnxoptIfODUkDirectionality has the value sink(1) and jnxoptIfODUkTCodirectional has the value true(1), or (iii) jnxoptIfODUkDirectionality has the value source(3) and jnxoptIfODUkTCodirectional has the value false(2). It must not be instantiated in rows for all other cases. This object has no effect when jnxoptIfODUkTTIMDetMode has the value off(1). The default value of this object is false(2).
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

jnxoptIfODUkTDEGThr 1.3.6.1.4.1.2636.3.73.1.1.9.1.1.9
Indicates the threshold level for declaring a performance monitoring (PM) Second to be bad. A PM Second is declared bad if the percentage of detected errored blocks in that second is greater than or equal to jnxoptIfODUkTDEGThr. This object is applicable only to the following three cases. (i) jnxoptIfODUkDirectionality has the value bidirectional(3), or (ii) jnxoptIfODUkDirectionality has the value sink(1) and jnxoptIfODUkTCodirectional has the value true(1), or (iii) jnxoptIfODUkDirectionality has the value source(3) and jnxoptIfODUkTCodirectional has the value false(2). It must not be instantiated in rows for all other cases. The default value of this object is Severely Errored Second (SES) Estimator (See ITU-T G.7710).
Status: current Access: read-create
OBJECT-TYPE    
  JnxoptIfDEGThr  

jnxoptIfODUkTDEGM 1.3.6.1.4.1.2636.3.73.1.1.9.1.1.10
Indicates the threshold level for declaring a Degraded Signal defect (dDEG). A dDEG shall be declared if jnxoptIfODUkTDEGM consecutive bad PM Seconds are detected. This object is applicable only to the following three cases. (i) jnxoptIfODUkDirectionality has the value bidirectional(3), or (ii) jnxoptIfODUkDirectionality has the value sink(1) and jnxoptIfODUkTCodirectional has the value true(1), or (iii) jnxoptIfODUkDirectionality has the value source(3) and jnxoptIfODUkTCodirectional has the value false(2). It must not be instantiated in rows for all other cases. The default value of this object is 7 (See ITU-T G.7710).
Status: current Access: read-create
OBJECT-TYPE    
  JnxoptIfDEGM  

jnxoptIfODUkTSinkMode 1.3.6.1.4.1.2636.3.73.1.1.9.1.1.11
This variable specifies the TCM mode at the entity. The value operational(1) means that TCM Overhead (TCMOH) processes (see ITU-T G.798) shall be performed and consequent actions for AIS, Trail Signal Fail (TSF), Trail Signal Degraded (TSD) shall be initiated in case of defects. The value monitor(2) means that TCMOH processes shall be performed but consequent actions for AIS, Trail Server Failure (TSF), Trail Server Degraded (TSD) shall _not_ be initiated in case of defects. This object is applicable only when the value of jnxoptIfODUkTtpPresent is false(2) and also either one of the following three cases holds: (i) jnxoptIfODUkDirectionality has the value bidirectional(3), or (ii) jnxoptIfODUkDirectionality has the value sink(1) and jnxoptIfODUkTCodirectional has the value true(1), or (iii) jnxoptIfODUkDirectionality has the value source(3) and jnxoptIfODUkTCodirectional has the value false(2). It must not be instantiated in rows for all other cases.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER operational(1), monitor(2)  

jnxoptIfODUkTSinkLockSignalAdminState 1.3.6.1.4.1.2636.3.73.1.1.9.1.1.12
Provides the capability to provision the LOCK signal, which is one of the ODUk maintenance signals, at the ODUKT sink. When a Tandem Connection endpoint is set to admin state locked, it inserts the ODUk-LCK signal in the sink direction. This object is applicable only when the value of jnxoptIfODUkTtpPresent is false(2) and also either one of the following three cases holds: (i) jnxoptIfODUkDirectionality has the value bidirectional(3), or (ii) jnxoptIfODUkDirectionality has the value sink(1) and jnxoptIfODUkTCodirectional has the value true(1), or (iii) jnxoptIfODUkDirectionality has the value source(3) and jnxoptIfODUkTCodirectional has the value false(2). It must not be instantiated in rows for all other cases.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER locked(1), normal(2)  

jnxoptIfODUkTSourceLockSignalAdminState 1.3.6.1.4.1.2636.3.73.1.1.9.1.1.13
Provides the capability to provision the LOCK signal, which is one of the ODUk maintenance signals, at the source. When a Tandem Connection endpoint is set to admin state locked, it inserts the ODUk-LCK signal in the source direction. This object is applicable only when either one of the following three cases holds: (i) jnxoptIfODUkDirectionality has the value bidirectional(3), or (ii) jnxoptIfODUkDirectionality has the value sink(1) and jnxoptIfODUkTCodirectional has the value false(2), or (iii) jnxoptIfODUkDirectionality has the value source(3) and jnxoptIfODUkTCodirectional has the value true(1). It must not be instantiated in rows for all other cases.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER locked(1), normal(2)  

jnxoptIfODUkTCurrentStatus 1.3.6.1.4.1.2636.3.73.1.1.9.1.1.14
Indicates the defect condition of the entity, if any. This object is applicable only when either one of the following three cases holds: (i) jnxoptIfODUkDirectionality has the value bidirectional(3), or (ii) jnxoptIfODUkDirectionality has the value sink(1) and jnxoptIfODUkTCodirectional has the value true(1), or (iii) jnxoptIfODUkDirectionality has the value source(3) and jnxoptIfODUkTCodirectional has the value false(2). It must not be instantiated in rows for all other cases.
Status: current Access: read-only
OBJECT-TYPE    
  BITS oci(0), lck(1), tim(2), deg(3), bdi(4), ssf(5)  

jnxoptIfODUkTRowStatus 1.3.6.1.4.1.2636.3.73.1.1.9.1.1.15
This columnar object is used for creating and deleting a conceptual row of the jnxoptIfODUkT config table. It is used to model the addTCM and removeTCM operations of an ODUk_CTP or ODUk_TTP for Tandem connection monitoring as defined in ITU-T G.874.1. Setting RowStatus to createAndGo or createAndWait implies addTCM. Setting RowStatus to destroy implies removeTCM. Successful addition/removal of TCM will result in updating the jnxoptIfODUkTcmFieldsInUse and jnxoptIfODUkPositionSeqCurrentSize variables and the jnxoptIfODUkPositionSeqTable table of the associated ODUk entry in the jnxoptIfODUkConfigTable.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

jnxoptIfODUkTNimConfigTable 1.3.6.1.4.1.2636.3.73.1.1.9.2
A table of ODUkTNim configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    JnxoptIfODUkTNimConfigEntry

jnxoptIfODUkTNimConfigEntry 1.3.6.1.4.1.2636.3.73.1.1.9.2.1
A conceptual row that contains ODUkTNim configuration information of an interface. Each instance must correspond to an instance of jnxoptIfODUkConfigEntry. Rows in this table are mutually exclusive with rows in the ODUkT config table -- in other words, this row object may not be instantiated for a given pair of ifIndex and TCM field values if a corresponding instance of jnxoptIfODUkTConfigEntry already exists. Instances of this conceptual row persist across agent restarts, and read-create columns other than the status column may be modified while the row is active.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfODUkTNimConfigEntry  

jnxoptIfODUkTNimTcmField 1.3.6.1.4.1.2636.3.73.1.1.9.2.1.1
Indicates the tandem connection monitoring field of the ODUk OH on which non-intrusive monitoring is performed. Valid values are integers from 1 to 6.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..6  

jnxoptIfODUkTNimDirectionality 1.3.6.1.4.1.2636.3.73.1.1.9.2.1.2
Specifies the monitor point for the ODUk TCM non-intrusive monitoring function. The value source(2) is not allowed if the corresponding instance of jnxoptIfODUkDirectionality has the value sink(1), and the value sink(1) is not allowed if the corresponding instance of jnxoptIfODUkDirectionality has the value source(2). Either the value sink(1) or source(2) is allowed if the corresponding instance of jnxoptIfODUkDirectionality has the value bidirectional(3). The value sink(1) means monitoring at the sink direction TCM signal of the ODUk CTP. The value source(2) means monitoring at the source direction path signal of the ODUk CTP.
Status: current Access: not-accessible
OBJECT-TYPE    
  JnxoptIfSinkOrSource  

jnxoptIfODUkTNimDAPIExpected 1.3.6.1.4.1.2636.3.73.1.1.9.2.1.3
The DAPI expected by the receiver. This object has no effect if jnxoptIfODUkTNimTIMDetMode has the value off(1) or sapi(3).
Status: current Access: read-create
OBJECT-TYPE    
  JnxoptIfExDAPI  

jnxoptIfODUkTNimSAPIExpected 1.3.6.1.4.1.2636.3.73.1.1.9.2.1.4
The SAPI expected by the receiver. This object has no effect if jnxoptIfODUkTNimTIMDetMode has the value off(1) or dapi(2).
Status: current Access: read-create
OBJECT-TYPE    
  JnxoptIfExSAPI  

jnxoptIfODUkTNimTraceIdentifierAccepted 1.3.6.1.4.1.2636.3.73.1.1.9.2.1.5
The actual trace identifier accepted. The value of this object is unspecified if jnxoptIfODUkTNimCurrentStatus has any of the bit positions oci(0), lck(1), or ssf(5) set or if jnxoptIfODUkTNimRowStatus has any value other than active(1).
Status: current Access: read-only
OBJECT-TYPE    
  JnxoptIfAcTI  

jnxoptIfODUkTNimTIMDetMode 1.3.6.1.4.1.2636.3.73.1.1.9.2.1.6
Indicates the mode of the Trace Identifier Mismatch (TIM) Detection function.
Status: current Access: read-create
OBJECT-TYPE    
  JnxoptIfTIMDetMode  

jnxoptIfODUkTNimTIMActEnabled 1.3.6.1.4.1.2636.3.73.1.1.9.2.1.7
Indicates whether the Trace Identifier Mismatch (TIM) Consequent Action function is enabled.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

jnxoptIfODUkTNimDEGThr 1.3.6.1.4.1.2636.3.73.1.1.9.2.1.8
Indicates the threshold level for declaring a performance monitoring (PM) Second to be bad. A PM Second is declared bad if the percentage of detected errored blocks in that second is greater than or equal to jnxoptIfODUkTNimDEGThr.
Status: current Access: read-create
OBJECT-TYPE    
  JnxoptIfDEGThr  

jnxoptIfODUkTNimDEGM 1.3.6.1.4.1.2636.3.73.1.1.9.2.1.9
Indicates the threshold level for declaring a Degraded Signal defect (dDEG). A dDEG shall be declared if jnxoptIfODUkTNimDEGM consecutive bad PM Seconds are detected.
Status: current Access: read-create
OBJECT-TYPE    
  JnxoptIfDEGM  

jnxoptIfODUkTNimCurrentStatus 1.3.6.1.4.1.2636.3.73.1.1.9.2.1.10
Indicates the defect condition of the entity, if any. The value of this object is unspecified if jnxoptIfODUkTNimRowStatus has any value other than active(1).
Status: current Access: read-only
OBJECT-TYPE    
  BITS oci(0), lck(1), tim(2), deg(3), bdi(4), ssf(5)  

jnxoptIfODUkTNimRowStatus 1.3.6.1.4.1.2636.3.73.1.1.9.2.1.11
This columnar object is used for creating and deleting a conceptual row of the jnxoptIfODUkTNim config table. It is used to model the addTCM and removeTCM operations of an ODUk_CTP or ODUk_TTP for non-intrusive Tandem connection monitoring as defined in ITU-T G.874.1. Setting RowStatus to createAndGo or createAndWait implies addTCM. Setting RowStatus to destroy implies removeTCM. Successful addition/removal of Nim TCM will result in updating the jnxoptIfODUkPositionSeqCurrentSize variable and the jnxoptIfODUkPositionSeqTable table of the associated ODUk entry in the jnxoptIfODUkConfigTable.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

jnxoptIfOTMnGroup 1.3.6.1.4.1.2636.3.73.1.2.1.1
A collection of OTMn structure information objects.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfPerfMonGroup 1.3.6.1.4.1.2636.3.73.1.2.1.2
A collection of performance monitoring interval objects.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfOTSnCommonGroup 1.3.6.1.4.1.2636.3.73.1.2.1.3
A collection of configuration objects applicable to all OTSn interfaces.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfOTSnSourceGroupFull 1.3.6.1.4.1.2636.3.73.1.2.1.4
A collection of configuration objects applicable to full-functionality/IaDI OTSn interfaces that support source functions.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfOTSnAPRStatusGroup 1.3.6.1.4.1.2636.3.73.1.2.1.5
A collection of objects applicable to OTSn interfaces that support Automatic Power Reduction functions.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfOTSnAPRControlGroup 1.3.6.1.4.1.2636.3.73.1.2.1.6
A collection of objects applicable to OTSn interfaces that provide Automatic Power Reduction control functions.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfOTSnSinkGroupBasic 1.3.6.1.4.1.2636.3.73.1.2.1.7
A collection of configuration objects applicable to all OTSn interfaces that support sink functions.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfOTSnSinkGroupFull 1.3.6.1.4.1.2636.3.73.1.2.1.8
A collection of configuration objects applicable to full-functionality/IaDI OTSn interfaces that support sink functions.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfOTSnSinkPreOtnPMGroup 1.3.6.1.4.1.2636.3.73.1.2.1.9
A collection of pre-OTN performance monitoring objects applicable to OTSn interfaces that support sink functions.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfOTSnSinkPreOtnPMThresholdGroup 1.3.6.1.4.1.2636.3.73.1.2.1.10
A collection of pre-OTN performance monitoring threshold objects applicable to OTSn interfaces that support sink functions.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfOTSnSourcePreOtnPMGroup 1.3.6.1.4.1.2636.3.73.1.2.1.11
A collection of pre-OTN performance monitoring objects applicable to OTSn interfaces that support source functions.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfOTSnSourcePreOtnPMThresholdGroup 1.3.6.1.4.1.2636.3.73.1.2.1.12
A collection of pre-OTN performance monitoring threshold objects applicable to OTSn interfaces that support source functions.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfOMSnCommonGroup 1.3.6.1.4.1.2636.3.73.1.2.1.13
A collection of configuration objects applicable to all OMSn interfaces.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfOMSnSinkGroupBasic 1.3.6.1.4.1.2636.3.73.1.2.1.14
A collection of configuration objects applicable to all OMSn interfaces that support sink functions.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfOMSnSinkPreOtnPMGroup 1.3.6.1.4.1.2636.3.73.1.2.1.15
A collection of pre-OTN performance monitoring objects applicable to OMSn interfaces that support sink functions.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfOMSnSinkPreOtnPMThresholdGroup 1.3.6.1.4.1.2636.3.73.1.2.1.16
A collection of pre-OTN performance monitoring threshold objects applicable to OMSn interfaces that support sink functions.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfOMSnSourcePreOtnPMGroup 1.3.6.1.4.1.2636.3.73.1.2.1.17
A collection of pre-OTN performance monitoring objects applicable to OMSn interfaces that support source functions.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfOMSnSourcePreOtnPMThresholdGroup 1.3.6.1.4.1.2636.3.73.1.2.1.18
A collection of pre-OTN performance monitoring threshold objects applicable to OMSn interfaces that that support source functions.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfOChGroupCommonGroup 1.3.6.1.4.1.2636.3.73.1.2.1.19
A collection of configuration objects applicable to all OChGroup interfaces.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfOChGroupSinkPreOtnPMGroup 1.3.6.1.4.1.2636.3.73.1.2.1.20
A collection of pre-OTN performance monitoring objects applicable to OChGroup interfaces that support sink functions.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfOChGroupSinkPreOtnPMThresholdGroup 1.3.6.1.4.1.2636.3.73.1.2.1.21
A collection of pre-OTN performance monitoring threshold objects applicable to OChGroup interfaces that support sink functions.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfOChGroupSourcePreOtnPMGroup 1.3.6.1.4.1.2636.3.73.1.2.1.22
A collection of pre-OTN performance monitoring objects applicable to OChGroup interfaces that support source functions.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfOChGroupSourcePreOtnPMThresholdGroup 1.3.6.1.4.1.2636.3.73.1.2.1.23
A collection of pre-OTN performance monitoring threshold objects applicable to OChGroup interfaces that that support source functions.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfOChCommonGroup 1.3.6.1.4.1.2636.3.73.1.2.1.24
A collection of configuration objects applicable to all OCh interfaces.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfOChSinkGroupBasic 1.3.6.1.4.1.2636.3.73.1.2.1.25
A collection of configuration objects applicable to all OCh interfaces that support sink functions.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfOChSinkPreOtnPMGroup 1.3.6.1.4.1.2636.3.73.1.2.1.26
A collection of pre-OTN performance monitoring objects applicable to OCh interfaces that support sink functions.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfOChSinkPreOtnPMThresholdGroup 1.3.6.1.4.1.2636.3.73.1.2.1.27
A collection of pre-OTN performance monitoring threshold objects applicable to OCh interfaces that support sink functions.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfOChSourcePreOtnPMGroup 1.3.6.1.4.1.2636.3.73.1.2.1.28
A collection of pre-OTN performance monitoring objects applicable to OCh interfaces that support source functions.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfOChSourcePreOtnPMThresholdGroup 1.3.6.1.4.1.2636.3.73.1.2.1.29
A collection of pre-OTN performance monitoring threshold objects applicable to OCh interfaces that support source functions.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfOTUkCommonGroup 1.3.6.1.4.1.2636.3.73.1.2.1.30
A collection of configuration objects applicable to all OTUk interfaces.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfOTUkSourceGroup 1.3.6.1.4.1.2636.3.73.1.2.1.31
A collection of configuration objects applicable to OTUk interfaces that support source functions.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfOTUkSinkGroup 1.3.6.1.4.1.2636.3.73.1.2.1.32
A collection of configuration objects applicable to OTUk interfaces that support sink functions.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfGCC0Group 1.3.6.1.4.1.2636.3.73.1.2.1.33
A collection of GCC0 configuration objects.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfODUkGroup 1.3.6.1.4.1.2636.3.73.1.2.1.34
A collection of configuration objects applicable to all ODUk interfaces.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfODUkTtpSourceGroup 1.3.6.1.4.1.2636.3.73.1.2.1.35
A collection of configuration objects applicable to all interfaces that support ODUk trail termination source functions.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfODUkTtpSinkGroup 1.3.6.1.4.1.2636.3.73.1.2.1.36
A collection of ODUk configuration objects applicable to all interfaces that support ODUk trail termination sink functions.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfODUkNimGroup 1.3.6.1.4.1.2636.3.73.1.2.1.37
A collection of ODUk Nim configuration objects.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfGCC12Group 1.3.6.1.4.1.2636.3.73.1.2.1.38
A collection of GCC12 configuration objects.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfODUkTCommonGroup 1.3.6.1.4.1.2636.3.73.1.2.1.39
A collection of configuration objects applicable to all ODUkT instances.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfODUkTSourceGroup 1.3.6.1.4.1.2636.3.73.1.2.1.40
A collection of configuration objects applicable to all ODUkT instances that provide source functions.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfODUkTSinkGroup 1.3.6.1.4.1.2636.3.73.1.2.1.41
A collection of configuration objects applicable to all ODUkT instances that provide sink functions.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfODUkTSinkGroupCtp 1.3.6.1.4.1.2636.3.73.1.2.1.42
A collection of configuration objects applicable to ODUkT instances not colocated with an ODUk TTP that provide sink functions.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfODUkTNimGroup 1.3.6.1.4.1.2636.3.73.1.2.1.43
A collection of ODUkT Nim configuration objects.
Status: current Access: read-create
OBJECT-GROUP    

jnxoptIfOtnConfigCompl 1.3.6.1.4.1.2636.3.73.1.2.2.1
Implementation requirements for the OTN configuration functions defined in this MIB module.
Status: current Access: read-create
MODULE-COMPLIANCE    

jnxoptIfPreOtnPMCompl 1.3.6.1.4.1.2636.3.73.1.2.2.2
Implementation requirements for Pre-OTN performance monitoring functions defined in this MIB module.
Status: current Access: read-create
MODULE-COMPLIANCE