JNX-OPT-IF-EXT-MIB

File: JNX-OPT-IF-EXT-MIB.mib (108234 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-TC	SNMP-FRAMEWORK-MIB
SNMPv2-CONF	IF-MIB	JNX-OPT-IF-MIB

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	Gauge32
Integer32	Unsigned32	Counter64
transmission	NOTIFICATION-TYPE	TEXTUAL-CONVENTION
RowPointer	RowStatus	TruthValue
DisplayString	DateAndTime	SnmpAdminString
MODULE-COMPLIANCE	OBJECT-GROUP	ifIndex
JnxoptIfDirectionality	jnxoptIfOChConfigEntry	jnxoptIfOChSinkCurrentEntry
jnxoptIfMibModule

Defined Types

JnxoptIfChannelSpacing
Channel spacing 1 - 100 GHz 2 - 50 GHz 3 - 25 GHz 4 - 12.5 GHz 5 - 6.25 GHz
TEXTUAL-CONVENTION
	INTEGER	spacing100Ghz(1), spacing50Ghz(2), spacing25Ghz(3), spacing12point5Ghz(4), spacing6point5Ghz(5)

JnxoptIfBitRateLineCoding
Optical tributary signal class 1 - NRZ 2.5G (from nominally 622 Mbit/s to nominally 2.67 Gbit/s) 2 - NRZ 10G nominally 2.4 Gbit/s to nominally 10.71 Gbit/s. 3 - 40 Gbits/s 4 - 100 Gbits/s 5 - 400 Gbits/s 40 Gbits/s and above are under study.
TEXTUAL-CONVENTION
	INTEGER	rate2point5G(1), rate10G(2), rate40G(3), rate100G(4), rate400G(5)

JnxoptIfFiberTypeRecommendation
Fiber Types - ITU-T Recs G.652, G.653, G.654 and G.655 One for recommendation and one for category. G.652 A, B, C, D G.653 A, B G.654 A, B, C G.655 C, D, E G.656 G.657 A, B
TEXTUAL-CONVENTION
	INTEGER	g652(1), g653(2), g654(3), g655(4), g656(5), g657(6)

JnxoptIfFiberTypeCategory
Fiber Types - ITU-T Recs G.652, G.653, G.654 and G.655 G.652 A, B, C, D G.653 A, B G.654 A, B, C G.655 C, D, E G.656 G.657 A, B Categories - A, B, C, D and E
TEXTUAL-CONVENTION
	INTEGER	categoryA(1), categoryB(2), categoryC(3), categoryD(4), categoryE(5)

JnxoptIfOTNType
This parameter indicates the parameters for the table are for the Near End or Far End performance data. 1 - Near End 2 - Far End
TEXTUAL-CONVENTION
	INTEGER	nearEnd(1), farEnd(2)

JnxoptIfOTNDirection
Indicates the direction as Rx/Tx or bi-directional.
TEXTUAL-CONVENTION
	INTEGER	jnxTxDir(1), jnxRxDir(2), jnxBiDir(3)

JnxoptIfOTNLayer
This parameter indicates the parameters for the table are for OTUk, ODUk, TCM performance data. 1 - OTUk 2 - ODUk 3 - TCM The ODUk layer and TCM sublayer PM is not related to the black link PM management, but since this could be a common PM model for the ODUk layer and TCM layers, we include it here so it may be used for simple scenarios where only lower order ODUk or higher order ODUk is present. For scenarios where both lower order ODUk and higher order ODUk are present, further extension to the MIB model is required, in particular for the indexing for these layers.
TEXTUAL-CONVENTION
	INTEGER	jnxoptIfOTUkLayer(1), jnxoptIfODUkLayer(2), jnxoptIfTCMSubLayer(3)

JnxoptIfOTNOChAlarms
This is the possible alarms from the OCh and OTUk layer.
TEXTUAL-CONVENTION
	INTEGER	jnxoptIfOtnNoAlarm(0), jnxoptIfOtnLosAlarm(1), jnxoptIfOtnLofAlarm(2), jnxoptIfOtnLomAlarm(3), jnxoptIfOtuSsfAlarm(4), jnxoptIfOtuBdiAlarm(5), jnxoptIfOtuTimAlarm(6), jnxoptIfOtuIaeAlarm(7), jnxoptIfOtuBiaeAlarm(8), jnxoptIfOtuTsfAlarm(9), jnxoptIfOtuDegAlarm(10), jnxoptIfOtuFecExcessiveErrsAlarm(11), jnxoptIf15MinThreshBBETCA(12), jnxoptIf15MinThreshESTCA(13), jnxoptIf15MinThreshSESTCA(14), jnxoptIf15MinThreshUASTCA(15), jnxoptIf15MinThreshBip8TCA(16), jnxoptIf15MinThUnCorrectedWordsTCA(17), jnxoptIf15MinThreshPreFECBERTCA(18), jnxoptIf24HourThreshBBETCA(19), jnxoptIf24HourThreshESTCA(20), jnxoptIf24HourThreshSESTCA(21), jnxoptIf24HourThreshUASTCA(22), jnxoptIf24HourThreshBip8TCA(23), jnxoptIf24HourThreshPreFECBERTCA(24), jnxoptIfOtuAisAlarm(25), jnxoptIfOtuFEFecErrAlarm(26)

JnxoptIfOTNODUkTcmAlarms
This is the alarms from the ODUk and TCM layer.
TEXTUAL-CONVENTION
	INTEGER	jnxoptIfOtnOdukTcmNoAlarm(0), jnxoptIfOdukTcmOciAlarm(1), jnxoptIfOdukTcmLckAlarm(2), jnxoptIfOdukTcmBdiAlarm(3), jnxoptIfOdukTcmTimAlarm(4), jnxoptIfOdukTcmDegAlarm(5), jnxoptIfOdukTcmIaeAlarm(6), jnxoptIfOdukTcmLTCAlarm(7), jnxoptIfOdukTcmCSfAlarm(8), jnxoptIfOdukTcmSSfAlarm(9), jnxoptIfOdukTcmTSfAlarm(10), jnxoptIfOdukTcm15MinThreshBBETCA(11), jnxoptIfOdukTcm15MinThreshESTCA(12), jnxoptIfOdukTcm15MinThreshSESTCA(13), jnxoptIfOdukTcm15MinThreshUASTCA(14), jnxoptIfOdukTcm15MinThreshBip8TCA(15), jnxoptIfOdukTcmAisAlarm(16), jnxoptIfOdukPtmAlarm(17), jnxoptIfOdukTcm24HourThreshBBETCA(18), jnxoptIfOdukTcm24HourThreshESTCA(19), jnxoptIfOdukTcm24HourThreshSESTCA(20), jnxoptIfOdukTcm24HourThreshUASTCA(21), jnxoptIfOdukTcm24HourThreshBip8TCA(22)

JnxoptIfOTNAlarmSeverity
Severity of the Notification
TEXTUAL-CONVENTION
	INTEGER	jnxCritical(1), jnxMajor(2), jnxMinor(3), jnxInfo(4)

JnxoptIfOPSmConfigEntry
SEQUENCE
	jnxoptIfOPSmDirectionality	JnxoptIfDirectionality
	jnxoptIfOPSmFiberTypeRecommendation	JnxoptIfFiberTypeRecommendation
	jnxoptIfOPSmFiberTypeCategory	JnxoptIfFiberTypeCategory

JnxoptIfOChConfigExtEntry
SEQUENCE
	jnxoptIfOChMiminumChannelSpacing	JnxoptIfChannelSpacing
	jnxoptIfOChBitRateLineCoding	JnxoptIfBitRateLineCoding
	jnxoptIfOChFEC	Unsigned32
	jnxoptIfOChSinkMaximumBERMantissa	Unsigned32
	jnxoptIfOChSinkMaximumBERExponent	Unsigned32
	jnxoptIfOChMinWavelength	Unsigned32
	jnxoptIfOChMaxWavelength	Unsigned32
	jnxoptIfOChWavelength	Unsigned32
	jnxoptIfOChVendorTransceiverClass	DisplayString
	jnxoptIfOChOpticalInterfaceApplicationCode	DisplayString
	jnxoptIfOChLaserAdminState	INTEGER
	jnxoptIfOChLaserOperationalState	INTEGER
	jnxoptIfOChAdminState	INTEGER
	jnxoptIfOChOperationalState	INTEGER

JnxoptIfOChSrcConfigEntry
SEQUENCE
	jnxoptIfOChMinimumMeanChannelOutputPower	Integer32
	jnxoptIfOChMaximumMeanChannelOutputPower	Integer32
	jnxoptIfOChMinimumCentralFrequency	Unsigned32
	jnxoptIfOChMaximumCentralFrequency	Unsigned32
	jnxoptIfOChMaximumSpectralExcursion	Unsigned32
	jnxoptIfOChMaximumTxDispersionOSNRPenalty	Integer32

JnxoptIfOChSrcSinkConfigEntry
SEQUENCE
	jnxoptIfOChSrcSinkMinimumChromaticDispersion	Integer32
	jnxoptIfOChSrcSinkMaximumChromaticDispersion	Integer32
	jnxoptIfOChSrcSinkMinimumSrcOpticalReturnLoss	Integer32
	jnxoptIfOChSrcSinkMaximumDiscreteReflectanceSrcToSink	Integer32
	jnxoptIfOChSrcSinkMaximumDifferentialGroupDelay	Integer32
	jnxoptIfOChSrcSinkMaximumPolarisationDependentLoss	Integer32
	jnxoptIfOChSrcSinkMaximumInterChannelCrosstalk	Integer32
	jnxoptIfOChSrcSinkInterFerometricCrosstalk	Integer32
	jnxoptIfOChSrcSinkOpticalPathOSNRPenalty	Integer32

JnxoptIfOChSinkConfigEntry
SEQUENCE
	jnxoptIfOChSinkMinimumMeanIntputPower	Integer32
	jnxoptIfOChSinkMaximumMeanIntputPower	Integer32
	jnxoptIfOChSinkMinimumOSNR	Integer32
	jnxoptIfOChSinkOSNRTolerance	Integer32

JnxoptIfOChSinkCurrentExtEntry
SEQUENCE
	jnxoptIfOChSinkCurrentChromaticDispersion	Integer32
	jnxoptIfOChSinkCurrentOSNR	Integer32
	jnxoptIfOChSinkCurrentQ	Integer32

JnxoptIfOTNPMConfigEntry
SEQUENCE
	jnxoptIfOTNPMConfigType	JnxoptIfOTNType
	jnxoptIfOTNPMConfigLayer	JnxoptIfOTNLayer
	jnxoptIfOTNPMConfigTCMLevel	Unsigned32
	jnxoptIfOTNPMESRInterval	Unsigned32
	jnxoptIfOTNPMSESRInterval	Unsigned32
	jnxoptIfOTNPMValidIntervals	Unsigned32
	jnxoptIfOTNPM15MinBip8Threshold	Unsigned32
	jnxoptIfOTNPM15MinESsThreshold	Unsigned32
	jnxoptIfOTNPM15MinSESsThreshold	Unsigned32
	jnxoptIfOTNPM15MinUASsThreshold	Unsigned32
	jnxoptIfOTNPM15MinBBEsThreshold	Unsigned32
	jnxoptIfOTNPM24HourBip8Threshold	Unsigned32
	jnxoptIfOTNPM24HourESsThreshold	Unsigned32
	jnxoptIfOTNPM24HourSESsThreshold	Unsigned32
	jnxoptIfOTNPM24HourUASsThreshold	Unsigned32
	jnxoptIfOTNPM24HourBBEsThreshold	Unsigned32
	jnxoptIfOTNPMBip8EnableTCA	TruthValue
	jnxoptIfOTNPMESsEnableTCA	TruthValue
	jnxoptIfOTNPMSESsEnableTCA	TruthValue
	jnxoptIfOTNPMUASsEnableTCA	TruthValue
	jnxoptIfOTNPMBBEsEnableTCA	TruthValue

JnxoptIfOTNPMCurrentEntry
SEQUENCE
	jnxoptIfOTNPMCurrentType	JnxoptIfOTNType
	jnxoptIfOTNPMCurrentLayer	JnxoptIfOTNLayer
	jnxoptIfOTNPMCurrentTCMLevel	Unsigned32
	jnxoptIfOTNPMCurrentSuspectedFlag	TruthValue
	jnxoptIfOTNPMCurrentBip8	Unsigned32
	jnxoptIfOTNPMCurrentESs	Unsigned32
	jnxoptIfOTNPMCurrentSESs	Unsigned32
	jnxoptIfOTNPMCurrentUASs	Unsigned32
	jnxoptIfOTNPMCurrentBBEs	Unsigned32
	jnxoptIfOTNPMCurrentESR	Unsigned32
	jnxoptIfOTNPMCurrentSESR	Unsigned32
	jnxoptIfOTNPMCurrentBBER	Unsigned32
	jnxoptIfOTNPMCurrentElapsedTime	Unsigned32
	jnxoptIfOTNPMCurSuspectReason	Integer32

JnxoptIfOTNPMIntervalEntry
SEQUENCE
	jnxoptIfOTNPMIntervalType	JnxoptIfOTNType
	jnxoptIfOTNPMIntervalLayer	JnxoptIfOTNLayer
	jnxoptIfOTNPMIntervalTCMLevel	Unsigned32
	jnxoptIfOTNPMIntervalNumber	Unsigned32
	jnxoptIfOTNPMIntervalSuspectedFlag	TruthValue
	jnxoptIfOTNPMIntervalBip8	Unsigned32
	jnxoptIfOTNPMIntervalESs	Unsigned32
	jnxoptIfOTNPMIntervalSESs	Unsigned32
	jnxoptIfOTNPMIntervalUASs	Unsigned32
	jnxoptIfOTNPMIntervalBBEs	Unsigned32
	jnxoptIfOTNPMIntervalESR	Unsigned32
	jnxoptIfOTNPMIntervalSESR	Unsigned32
	jnxoptIfOTNPMIntervalBBER	Unsigned32
	jnxoptIfOTNPMIntervalTimeStamp	DateAndTime
	jnxoptIfOTNPMIntSuspectReason	Integer32

JnxoptIfOTNPMCurrentDayEntry
SEQUENCE
	jnxoptIfOTNPMCurrentDayType	JnxoptIfOTNType
	jnxoptIfOTNPMCurrentDayLayer	JnxoptIfOTNLayer
	jnxoptIfOTNPMCurrentDayTCMLevel	Unsigned32
	jnxoptIfOTNPMCurrentDaySuspectedFlag	TruthValue
	jnxoptIfOTNPMCurrentDayBip8	Unsigned32
	jnxoptIfOTNPMCurrentDayESs	Unsigned32
	jnxoptIfOTNPMCurrentDaySESs	Unsigned32
	jnxoptIfOTNPMCurrentDayUASs	Unsigned32
	jnxoptIfOTNPMCurrentDayBBEs	Unsigned32
	jnxoptIfOTNPMCurrentDayESR	Unsigned32
	jnxoptIfOTNPMCurrentDaySESR	Unsigned32
	jnxoptIfOTNPMCurrentDayBBER	Unsigned32
	jnxoptIfOTNPMCurrentDayElapsedTime	Unsigned32
	jnxoptIfOTNPMCurDaySuspectReason	Integer32

JnxoptIfOTNPMPrevDayEntry
SEQUENCE
	jnxoptIfOTNPMPrevDayType	JnxoptIfOTNType
	jnxoptIfOTNPMPrevDayLayer	JnxoptIfOTNLayer
	jnxoptIfOTNPMPrevDayTCMLevel	Unsigned32
	jnxoptIfOTNPMPrevDaySuspectedFlag	TruthValue
	jnxoptIfOTNPMPrevDayBip8	Unsigned32
	jnxoptIfOTNPMPrevDayESs	Unsigned32
	jnxoptIfOTNPMPrevDaySESs	Unsigned32
	jnxoptIfOTNPMPrevDayUASs	Unsigned32
	jnxoptIfOTNPMPrevDayBBEs	Unsigned32
	jnxoptIfOTNPMPrevDayESR	Unsigned32
	jnxoptIfOTNPMPrevDaySESR	Unsigned32
	jnxoptIfOTNPMPrevDayBBER	Unsigned32
	jnxoptIfOTNPMPrevDayTimeStamp	DateAndTime
	jnxoptIfOTNPMPrevDaySuspectReason	Integer32

JnxoptIfOTNPMFECConfigEntry
SEQUENCE
	jnxoptIfOTNPMFECConfigType	JnxoptIfOTNType
	jnxoptIfOTNPMFECValidIntervals	Unsigned32
	jnxoptIfOTNPM15MinPreFECBERMantissaThreshold	Unsigned32
	jnxoptIfOTNPM15MinPreFECBERExponentThreshold	Unsigned32
	jnxoptIfOTNPM24HourPreFECBERMantissaThreshold	Unsigned32
	jnxoptIfOTNPM24HourPreFECBERExponentThreshold	Unsigned32
	jnxoptIfOTNPMFECBEREnableTCA	TruthValue

JnxoptIfOTNPMFECCurrentEntry
SEQUENCE
	jnxoptIfOTNPMFECCurrentType	JnxoptIfOTNType
	jnxoptIfOTNPMFECCurrentSuspectedFlag	TruthValue
	jnxoptIfOTNPMCurrentFECCorrectedErr	Counter64
	jnxoptIfOTNPMCurrentFECUncorrectedWords	Counter64
	jnxoptIfOTNPMCurrentFECBERMantissa	Unsigned32
	jnxoptIfOTNPMCurrentFECBERExponent	Unsigned32
	jnxoptIfOTNPMCurrentFECMinBERMantissa	Unsigned32
	jnxoptIfOTNPMCurrentFECMinBERExponent	Unsigned32
	jnxoptIfOTNPMCurrentFECMaxBERMantissa	Unsigned32
	jnxoptIfOTNPMCurrentFECMaxBERExponent	Unsigned32
	jnxoptIfOTNPMCurrentFECAvgBERMantissa	Unsigned32
	jnxoptIfOTNPMCurrentFECAvgBERExponent	Unsigned32
	jnxoptIfOTNPMCurrentFECElapsedTime	Unsigned32
	jnxoptIfOTNPMFECCurSuspectReason	Integer32

JnxoptIfOTNPMFECIntervalEntry
SEQUENCE
	jnxoptIfOTNPMFECIntervalType	JnxoptIfOTNType
	jnxoptIfOTNPMFECIntervalNumber	Unsigned32
	jnxoptIfOTNPMFECIntervalSuspectedFlag	TruthValue
	jnxoptIfOTNPMIntervalFECCorrectedErr	Counter64
	jnxoptIfOTNPMIntervalFECUncorrectedWords	Counter64
	jnxoptIfOTNPMIntervalMinFECBERMantissa	Unsigned32
	jnxoptIfOTNPMIntervalMinFECBERExponent	Unsigned32
	jnxoptIfOTNPMIntervalMaxFECBERMantissa	Unsigned32
	jnxoptIfOTNPMIntervalMaxFECBERExponent	Unsigned32
	jnxoptIfOTNPMIntervalAvgFECBERMantissa	Unsigned32
	jnxoptIfOTNPMIntervalAvgFECBERExponent	Unsigned32
	jnxoptIfOTNPMFECIntervalTimeStamp	DateAndTime
	jnxoptIfOTNPMFECIntSuspectReason	Integer32

JnxoptIfOTNPMFECCurrentDayEntry
SEQUENCE
	jnxoptIfOTNPMFECCurrentDayType	JnxoptIfOTNType
	jnxoptIfOTNPMFECCurrentDaySuspectedFlag	TruthValue
	jnxoptIfOTNPMCurrentDayFECCorrectedErr	Counter64
	jnxoptIfOTNPMCurrentDayFECUncorrectedWords	Counter64
	jnxoptIfOTNPMCurrentDayMinFECBERMantissa	Unsigned32
	jnxoptIfOTNPMCurrentDayMinFECBERExponent	Unsigned32
	jnxoptIfOTNPMCurrentDayMaxFECBERMantissa	Unsigned32
	jnxoptIfOTNPMCurrentDayMaxFECBERExponent	Unsigned32
	jnxoptIfOTNPMCurrentDayAvgFECBERMantissa	Unsigned32
	jnxoptIfOTNPMCurrentDayAvgFECBERExponent	Unsigned32
	jnxoptIfOTNPMFECCurrentDayElapsedTime	Unsigned32
	jnxoptIfOTNPMFECCurDaySuspectReason	Integer32

JnxoptIfOTNPMFECPrevDayEntry
SEQUENCE
	jnxoptIfOTNPMFECPrevDayType	JnxoptIfOTNType
	jnxoptIfOTNPMFECPrevDaySuspectedFlag	TruthValue
	jnxoptIfOTNPMPrevDayFECCorrectedErr	Counter64
	jnxoptIfOTNPMPrevDayFECUncorrectedWords	Counter64
	jnxoptIfOTNPMPrevDayMinFECBERMantissa	Unsigned32
	jnxoptIfOTNPMPrevDayMinFECBERExponent	Unsigned32
	jnxoptIfOTNPMPrevDayMaxFECBERMantissa	Unsigned32
	jnxoptIfOTNPMPrevDayMaxFECBERExponent	Unsigned32
	jnxoptIfOTNPMPrevDayAvgFECBERMantissa	Unsigned32
	jnxoptIfOTNPMPrevDayAvgFECBERExponent	Unsigned32
	jnxoptIfOTNPMFECPrevDayTimeStamp	DateAndTime
	jnxoptIfOTNPMFECPrevDaySuspectReason	Integer32

JnxoptIfOTNAlarmEntry
SEQUENCE
	jnxoptIfOTNAlarmLocation	JnxoptIfOTNType
	jnxoptIfOTNAlarmDirection	JnxoptIfOTNDirection
	jnxoptIfOTNAlarmLayer	JnxoptIfOTNLayer
	jnxoptIfOTNAlarmTCMLevel	Unsigned32
	jnxoptIfOTNOChOTUkAlarmType	JnxoptIfOTNOChAlarms
	jnxoptIfOTNAlarmSeverity	JnxoptIfOTNAlarmSeverity
	jnxoptIfOTNAlarmDate	DateAndTime
	jnxoptIfOTNODUkTcmAlarmType	JnxoptIfOTNODUkTcmAlarms

Defined Values

jnxoptIfExtMibModule		1.3.6.1.4.1.2636.3.73.1.3
The MIB module to describe Black Link extension to rfc3591. It is the enterprise version of the draft draft-galikunze-ccamp-g-698-2-snmp-mib-02
MODULE-IDENTITY

jnxoptIfOTNNotifications		1.3.6.1.4.1.2636.3.73.1.3.0
OBJECT IDENTIFIER

jnxoptIfOPSmEntry		1.3.6.1.4.1.2636.3.73.1.3.1
OBJECT IDENTIFIER

jnxoptIfOChSrcSinkGroup		1.3.6.1.4.1.2636.3.73.1.3.2
OBJECT IDENTIFIER

jnxoptIfOTNPMGroup		1.3.6.1.4.1.2636.3.73.1.3.3
OBJECT IDENTIFIER

jnxoptIfOTNAlarm		1.3.6.1.4.1.2636.3.73.1.3.4
OBJECT IDENTIFIER

jnxoptIfOPSmConfigTable		1.3.6.1.4.1.2636.3.73.1.3.1.1
A table of OPS General config parameters.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		JnxoptIfOPSmConfigEntry

jnxoptIfOPSmConfigEntry		1.3.6.1.4.1.2636.3.73.1.3.1.1.1
An conceptual row of OPS General config parameters.
Status: current	Access: not-accessible
OBJECT-TYPE
	JnxoptIfOPSmConfigEntry

jnxoptIfOPSmDirectionality		1.3.6.1.4.1.2636.3.73.1.3.1.1.1.1
Indicates the directionality of the entity.
Status: current	Access: read-only
OBJECT-TYPE
	JnxoptIfDirectionality

jnxoptIfOPSmFiberTypeRecommendation		1.3.6.1.4.1.2636.3.73.1.3.1.1.1.2
Fiber type as per fibre types are chosen from those defined in ITU-T Recs G.652, G.653, G.654, G.655, G.656 and G.657.
Status: current	Access: read-only
OBJECT-TYPE
	JnxoptIfFiberTypeRecommendation

jnxoptIfOPSmFiberTypeCategory		1.3.6.1.4.1.2636.3.73.1.3.1.1.1.3
Fiber type as per fibre types are chosen from those defined in ITU-T Recs G.652, G.653, and G.655. The categories are A, B, C, D and E.
Status: current	Access: read-only
OBJECT-TYPE
	JnxoptIfFiberTypeCategory

jnxoptIfOChConfigExtTable		1.3.6.1.4.1.2636.3.73.1.3.2.1
A table of Och General config extension parameters
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		JnxoptIfOChConfigExtEntry

jnxoptIfOChConfigExtEntry		1.3.6.1.4.1.2636.3.73.1.3.2.1.1
A conceptual row that contains OCh configuration extension information of an interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	JnxoptIfOChConfigExtEntry

jnxoptIfOChMiminumChannelSpacing		1.3.6.1.4.1.2636.3.73.1.3.2.1.1.1
A minimum nominal difference in frequency (GHz) between two adjacent channels.
Status: current	Access: read-only
OBJECT-TYPE
	JnxoptIfChannelSpacing

jnxoptIfOChBitRateLineCoding		1.3.6.1.4.1.2636.3.73.1.3.2.1.1.2
Optical tributary signal class NRZ 2.5G (from nominally 622 Mbit/s to nominally 2.67 Gbit/s) NRZ 10G (nominally 2.4 Gbit/s to nominally 10.71 Gbit/s)
Status: current	Access: read-only
OBJECT-TYPE
	JnxoptIfBitRateLineCoding

jnxoptIfOChFEC		1.3.6.1.4.1.2636.3.73.1.3.2.1.1.3
This parameter indicates what Forward Error Correction (FEC) code is used at Source and Sink. GFEC (from G709) and the I.x EFEC's (G.975 - Table I.1 super FEC). 1 - No FEC 2 - GFEC 3 - I.2 EFEC 4 - I.3 EFEC 5 - I.4 EFEC 6 - I.5 EFEC 7 - I.6 EFEC 8 - I.7 EFEC 9 - I.8 EFEC 10 - I.9 EFEC 11 - 100G FEC (for new applications) 12 - 100G EFEC (for new applications) 99 - Vendor Specific
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

jnxoptIfOChSinkMaximumBERMantissa		1.3.6.1.4.1.2636.3.73.1.3.2.1.1.4
This parameter indicate the maximum Bit(mantissa) error rate can be supported by the application at the Receiver. In case of FEC applications it is intended after the FEC correction.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOChSinkMaximumBERExponent		1.3.6.1.4.1.2636.3.73.1.3.2.1.1.5
This parameter indicate the maximum Bit(exponent) error rate can be supported by the application at the Receiver. In case of FEC applications it is intended after the FEC correction.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOChMinWavelength		1.3.6.1.4.1.2636.3.73.1.3.2.1.1.6
This parameter indicate minimum wavelength spectrum in a definite wavelength Band (L, C and S)
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOChMaxWavelength		1.3.6.1.4.1.2636.3.73.1.3.2.1.1.7
This parameter indicate maximum wavelength spectrum in a definite wavelength Band (L, C and S)
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOChWavelength		1.3.6.1.4.1.2636.3.73.1.3.2.1.1.8
This parameter indicates the wavelength value.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

jnxoptIfOChVendorTransceiverClass		1.3.6.1.4.1.2636.3.73.1.3.2.1.1.9
As defined in G.698 Vendors can summarize a set of parameters in a single proprietary parameter: the Class of transceiver. The Transceiver classification will be based on the Vendor Name and the main TX and RX parameters (i.e. Trunk Mode, Framing, Bit rate, Trunk Type etc). If this parameter is used, the MIB parameters specifying the Transceiver characteristics may not be significant and the vendor will be responsible to specify the Class contents and values. The Vendor can publish the parameters of its Classes or declare to be compatible with published Classes.(G) Optional for compliance. (not mentioned in G.698)
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..64)

jnxoptIfOChOpticalInterfaceApplicationCode		1.3.6.1.4.1.2636.3.73.1.3.2.1.1.10
This parameter indicates the transceiver application code at Ss and Rs as defined in [ITU.G698.2] Chapter 5.3
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..64)

jnxoptIfOChLaserAdminState		1.3.6.1.4.1.2636.3.73.1.3.2.1.1.11
The configured State of the laser: 0 - disabled 1 - enabled
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(0), enabled(1)

jnxoptIfOChLaserOperationalState		1.3.6.1.4.1.2636.3.73.1.3.2.1.1.12
The Operational Status of Laser: 0 - disabled 1 - Enabled 2 - fault 3 - degraded
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(0), enabled(1), fault(2), degraded(3)

jnxoptIfOChAdminState		1.3.6.1.4.1.2636.3.73.1.3.2.1.1.13
The Administrative Status of an Interface: 0 - Out of Service 1 - In Service
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

jnxoptIfOChOperationalState		1.3.6.1.4.1.2636.3.73.1.3.2.1.1.14
The Operational Status of an Interface: 0 - disabled 1 - enabled 2 - Fault 3 - Degraded
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(0), enabled(1), fault(2), degraded(3)

jnxoptIfOChSrcConfigTable		1.3.6.1.4.1.2636.3.73.1.3.2.2
A configuration table of OCh Src (Ss) parameters.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		JnxoptIfOChSrcConfigEntry

jnxoptIfOChSrcConfigEntry		1.3.6.1.4.1.2636.3.73.1.3.2.2.1
A conceptual row that contains the Src (Ss) configuration parameters for a given interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	JnxoptIfOChSrcConfigEntry

jnxoptIfOChMinimumMeanChannelOutputPower		1.3.6.1.4.1.2636.3.73.1.3.2.2.1.1
The minimum mean launched power at Ss is the average power (in dbm) of a pseudo-random data sequence coupled into the DWDM link.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

jnxoptIfOChMaximumMeanChannelOutputPower		1.3.6.1.4.1.2636.3.73.1.3.2.2.1.2
The maximum mean launched power at Ss is the average power (in dbm) of a pseudo-random data sequence coupled into the DWDM link.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

jnxoptIfOChMinimumCentralFrequency		1.3.6.1.4.1.2636.3.73.1.3.2.2.1.3
The minimum central frequency is the nominal single-channel frequency (in THz) on which the digital coded information of the particular optical channel is modulated by use of the NRZ line code. Eg 191.5THz will be represented as 19150
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOChMaximumCentralFrequency		1.3.6.1.4.1.2636.3.73.1.3.2.2.1.4
The maximum central frequency is the nominal single-channel frequency (in THz) on which the digital coded information of the particular optical channel is modulated by use of the NRZ line code. Eg 191.5THz will be represented as 19150
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOChMaximumSpectralExcursion		1.3.6.1.4.1.2636.3.73.1.3.2.2.1.5
This is the maximum acceptable difference between the nominal central frequency (in GHz) of the channel and the minus 15 dB points of the transmitter spectrum furthest from the nominal central frequency measured at point Ss.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOChMaximumTxDispersionOSNRPenalty		1.3.6.1.4.1.2636.3.73.1.3.2.2.1.6
Defines a reference receiver that this penalty is measured with. Lowest OSNR at Ss with worst case (residual) dispersion minus the Lowest OSNR at Ss with no dispersion. Lowest OSNR at Ss with no dispersion
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

jnxoptIfOChSrcSinkConfigTable		1.3.6.1.4.1.2636.3.73.1.3.2.3
A table of paramters for the optical path from Src to Sink (Ss to Rs).
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		JnxoptIfOChSrcSinkConfigEntry

jnxoptIfOChSrcSinkConfigEntry		1.3.6.1.4.1.2636.3.73.1.3.2.3.1
A conceptual row that contains the optical path Src-Sink (Ss-Rs) configuration parameters for a given interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	JnxoptIfOChSrcSinkConfigEntry

jnxoptIfOChSrcSinkMinimumChromaticDispersion		1.3.6.1.4.1.2636.3.73.1.3.2.3.1.1
These parameters define the minimum value of the optical path 'end to end chromatic dispersion' (in ps/nm) that the system shall be able to tolerate.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

jnxoptIfOChSrcSinkMaximumChromaticDispersion		1.3.6.1.4.1.2636.3.73.1.3.2.3.1.2
These parameters define the maximum value of the optical path 'end to end chromatic dispersion' (in ps/nm) that the system shall be able to tolerate.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

jnxoptIfOChSrcSinkMinimumSrcOpticalReturnLoss		1.3.6.1.4.1.2636.3.73.1.3.2.3.1.3
These parameter defines minimum optical return loss (in dB) of the cable plant at the source reference point (Src/Ss), including any connectors.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

jnxoptIfOChSrcSinkMaximumDiscreteReflectanceSrcToSink		1.3.6.1.4.1.2636.3.73.1.3.2.3.1.4
Optical reflectance is defined to be the ratio of the reflected optical power pre.sent at a point, to the optical power incident to that point. Control of reflections is discussed extensively in ITU-T Rec. G.957.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

jnxoptIfOChSrcSinkMaximumDifferentialGroupDelay		1.3.6.1.4.1.2636.3.73.1.3.2.3.1.5
Differential group delay (DGD) is the time difference between the fractions of a pulse that are transmitted in the two principal states of polarization of an optical signal. For distances greater than several kilometres, and assuming random (strong) polarization mode coupling, DGD in a fibre can be statistically modelled as having a Maxwellian distribution.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

jnxoptIfOChSrcSinkMaximumPolarisationDependentLoss		1.3.6.1.4.1.2636.3.73.1.3.2.3.1.6
The polarisation dependent loss (PDL) is the difference (in dB) between the maximum and minimum values of the channel insertion loss (or gain) of the black-link from point SS to RS due to a variation of the state of polarization (SOP) over all SOPs.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

jnxoptIfOChSrcSinkMaximumInterChannelCrosstalk		1.3.6.1.4.1.2636.3.73.1.3.2.3.1.7
Inter-channel crosstalk is defined as the ratio of total power in all of the disturbing channels to that in the wanted channel, where the wanted and disturbing channels are at different wavelengths. The parameter specify the isolation of a link conforming to the 'black-link' approach such that under the worst- case operating conditions the inter-channel crosstalk at any reference point RS is less than the maximum inter-channel crosstalk value.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

jnxoptIfOChSrcSinkInterFerometricCrosstalk		1.3.6.1.4.1.2636.3.73.1.3.2.3.1.8
This parameter places a requirement on the isolation of a link conforming to the 'black-link' approach such that under the worst case operating conditions the interferometric crosstalk at any reference point RS is less than the maximum interferometric crosstalk value..
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

jnxoptIfOChSrcSinkOpticalPathOSNRPenalty		1.3.6.1.4.1.2636.3.73.1.3.2.3.1.9
The optical path OSNR penalty is defined as the difference between the Lowest OSNR at Rs and Lowest OSNR at Ss that meets the BER requirement.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

jnxoptIfOChSinkConfigTable		1.3.6.1.4.1.2636.3.73.1.3.2.4
A table of OCh Sink (Rs) configuration parameters.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		JnxoptIfOChSinkConfigEntry

jnxoptIfOChSinkConfigEntry		1.3.6.1.4.1.2636.3.73.1.3.2.4.1
A conceptual row that contains the Sink (Rs) configuration parameters for a given interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	JnxoptIfOChSinkConfigEntry

jnxoptIfOChSinkMinimumMeanIntputPower		1.3.6.1.4.1.2636.3.73.1.3.2.4.1.1
The minimum values of the average received power (in dbm at point the Sink (Rs).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

jnxoptIfOChSinkMaximumMeanIntputPower		1.3.6.1.4.1.2636.3.73.1.3.2.4.1.2
The maximum values of the average received power (in dbm) at point the Sink (Rs).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

jnxoptIfOChSinkMinimumOSNR		1.3.6.1.4.1.2636.3.73.1.3.2.4.1.3
The minimum optical signal-to-noise ratio (OSNR) is the minimum value of the ratio of the signal power in the wanted channel to the highest noise power density in the range of the central frequency plus and minus the maximum spectral excursion.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

jnxoptIfOChSinkOSNRTolerance		1.3.6.1.4.1.2636.3.73.1.3.2.4.1.4
The receiver OSNR tolerance is defined as the minimum value of OSNR at point Sink (Rs) that can be tolerated while maintaining the maximum BER of the application. Sink (Rs).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

jnxoptIfOChSinkCurrentExtTable		1.3.6.1.4.1.2636.3.73.1.3.3.1
A table of OCh sink etxension to the performance monitoring information for the current 15-minute interval.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		JnxoptIfOChSinkCurrentExtEntry

jnxoptIfOChSinkCurrentExtEntry		1.3.6.1.4.1.2636.3.73.1.3.3.1.1
A conceptual row that contains OCh sink performance monitoring information for an interface for the current 15-minute interval.
Status: current	Access: not-accessible
OBJECT-TYPE
	JnxoptIfOChSinkCurrentExtEntry

jnxoptIfOChSinkCurrentChromaticDispersion		1.3.6.1.4.1.2636.3.73.1.3.3.1.1.1
Residual Chromatic Dispersion measured at Rx Transceiver port.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

jnxoptIfOChSinkCurrentOSNR		1.3.6.1.4.1.2636.3.73.1.3.3.1.1.2
Current Optical Signal to Noise Ratio (OSNR) estimated at Rx Transceiver port .
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

jnxoptIfOChSinkCurrentQ		1.3.6.1.4.1.2636.3.73.1.3.3.1.1.3
'Q' factor estimated at Rx Transceiver port.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

jnxoptIfOTNPMConfigTable		1.3.6.1.4.1.2636.3.73.1.3.3.2
A table of performance monitoring configuration for the type 'jnxoptIfOTNPMConfigLayer' layer.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		JnxoptIfOTNPMConfigEntry

jnxoptIfOTNPMConfigEntry		1.3.6.1.4.1.2636.3.73.1.3.3.2.1
A conceptual entry in the performance monitoring configuration for the type 'jnxoptIfOTNPMConfigLayer' layer.
Status: current	Access: not-accessible
OBJECT-TYPE
	JnxoptIfOTNPMConfigEntry

jnxoptIfOTNPMConfigType		1.3.6.1.4.1.2636.3.73.1.3.3.2.1.1
This parameter indicates the parameters for the table are for the Near End or Far End performance data. 1 - Near End 2 - Far End
Status: current	Access: not-accessible
OBJECT-TYPE
	JnxoptIfOTNType

jnxoptIfOTNPMConfigLayer		1.3.6.1.4.1.2636.3.73.1.3.3.2.1.2
This parameter indicates the parameters for the table are for OTUk, ODUk, TCMn performance data. 1 - OTUk 2 - ODUk 3 - TCM The ODUk/TCM sublayer PM is not related to the black link PM management, but since this is a common PM model for the ODU/TCM layer, we may include it here.
Status: current	Access: not-accessible
OBJECT-TYPE
	JnxoptIfOTNLayer

jnxoptIfOTNPMConfigTCMLevel		1.3.6.1.4.1.2636.3.73.1.3.3.2.1.3
This parameter indicates the TCM level (1-6) if the PM is of the type TCM. This will be 0 for OTUK/ODUK.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	0..6

jnxoptIfOTNPMESRInterval		1.3.6.1.4.1.2636.3.73.1.3.3.2.1.4
This parameter indicates the measurement interval for error seconds ratio.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	1..96

jnxoptIfOTNPMSESRInterval		1.3.6.1.4.1.2636.3.73.1.3.3.2.1.5
This parameter indicates the measurement interval for severely error seconds ratio.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMValidIntervals		1.3.6.1.4.1.2636.3.73.1.3.3.2.1.6
The number of contiguous 15 minute intervals for which valid PM data is available for the particular interface.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPM15MinBip8Threshold		1.3.6.1.4.1.2636.3.73.1.3.3.2.1.7
The number of Bip8 encountered by the interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send jnxoptIf15MinThreshBip8TCA. One notification will be sent per interval per interface. A value of `0' will disable the notification.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPM15MinESsThreshold		1.3.6.1.4.1.2636.3.73.1.3.3.2.1.8
The number of ES encountered by the interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send jnxoptIf15MinThreshEsTCA. One notification will be sent per interval per interface. A value of `0' will disable the notification.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPM15MinSESsThreshold		1.3.6.1.4.1.2636.3.73.1.3.3.2.1.9
The number of SES encountered by the interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send jnxoptIf15MinThreshSESTCA. One notification will be sent per interval per interface. A value of `0' will disable the notification.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPM15MinUASsThreshold		1.3.6.1.4.1.2636.3.73.1.3.3.2.1.10
The number of UAS encountered by the interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send jnxoptIf15MinThreshUASTCA. One notification will be sent per interval per interface. A value of `0' will disable the notification.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPM15MinBBEsThreshold		1.3.6.1.4.1.2636.3.73.1.3.3.2.1.11
The number of UAS encountered by the interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send jnxoptIf15MinThreshBBETCA. One notification will be sent per interval per interface. A value of `0' will disable the notification.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPM24HourBip8Threshold		1.3.6.1.4.1.2636.3.73.1.3.3.2.1.12
The number of Bip8 encountered by the interface within any given 24 Hour performance data collection period, which causes the SNMP agent to send jnxoptIf15MinThreshBip8TCA. One notification will be sent per interval per interface. A value of `0' will disable the notification.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPM24HourESsThreshold		1.3.6.1.4.1.2636.3.73.1.3.3.2.1.13
The number of ES encountered by the interface within any given 24 hour performance data collection period, which causes the SNMP agent to send jnxoptIf24HourThreshEsTCA. One notification will be sent per 24 hour per interface. A value of `0' will disable the notification.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPM24HourSESsThreshold		1.3.6.1.4.1.2636.3.73.1.3.3.2.1.14
The number of SES encountered by the interface within any given 24 hour performance data collection period, which causes the SNMP agent to send jnxoptIf24HourThreshSESsTCA. One notification will be sent per 24 hour per interface. A value of `0' will disable the notification.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPM24HourUASsThreshold		1.3.6.1.4.1.2636.3.73.1.3.3.2.1.15
The number of SES encountered by the interface within any given 24 hour performance data collection period, which causes the SNMP agent to send jnxoptIf24HourThreshUASsTCA. One notification will be sent per 24 hour per interface. A value of `0' will disable the notification.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPM24HourBBEsThreshold		1.3.6.1.4.1.2636.3.73.1.3.3.2.1.16
The number of BBE encountered by the interface within any given 24 hour performance data collection period, which causes the SNMP agent to send jnxoptIf24HourThreshBBEsTCA. One notification will be sent per 24 hour per interface. A value of `0' will disable the notification.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMBip8EnableTCA		1.3.6.1.4.1.2636.3.73.1.3.3.2.1.17
Enable TCA's - 15minute and 24hr for Bip8
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

jnxoptIfOTNPMESsEnableTCA		1.3.6.1.4.1.2636.3.73.1.3.3.2.1.18
Enable TCA's - 15minute and 24hr for ESs
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

jnxoptIfOTNPMSESsEnableTCA		1.3.6.1.4.1.2636.3.73.1.3.3.2.1.19
Enable TCA's - 15minute and 24hr for SESs
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

jnxoptIfOTNPMUASsEnableTCA		1.3.6.1.4.1.2636.3.73.1.3.3.2.1.20
Enable TCA's - 15minute and 24hr for UASs
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

jnxoptIfOTNPMBBEsEnableTCA		1.3.6.1.4.1.2636.3.73.1.3.3.2.1.21
Enable TCA's - 15minute and 24hr for BBEs
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

jnxoptIfOTNPMCurrentTable		1.3.6.1.4.1.2636.3.73.1.3.3.3
A table for the Performance monitoring Current Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		JnxoptIfOTNPMCurrentEntry

jnxoptIfOTNPMCurrentEntry		1.3.6.1.4.1.2636.3.73.1.3.3.3.1
A conceptual entry in the Near end or Far End performance monitoring Current table for the type 'jnxoptIfOTNPMCurrentLayer' layer.
Status: current	Access: not-accessible
OBJECT-TYPE
	JnxoptIfOTNPMCurrentEntry

jnxoptIfOTNPMCurrentType		1.3.6.1.4.1.2636.3.73.1.3.3.3.1.1
This parameter indicates the parameters for the table are for the Near End or Far End performance data. 1 - Near End 2 - Far End
Status: current	Access: not-accessible
OBJECT-TYPE
	JnxoptIfOTNType

jnxoptIfOTNPMCurrentLayer		1.3.6.1.4.1.2636.3.73.1.3.3.3.1.2
This parameter indicates the parameters for the table are for OTUk, ODUk, TCMn performance data. 1 - OTUk (OCh which is used for the black link) 2 - ODUk 3 - TCM The ODUk/TCM sublayer PM is not related to the black link PM management, but since this is a common PM model for the ODU/TCM layer, we may include it here.
Status: current	Access: not-accessible
OBJECT-TYPE
	JnxoptIfOTNLayer

jnxoptIfOTNPMCurrentTCMLevel		1.3.6.1.4.1.2636.3.73.1.3.3.3.1.3
This parameter indicates the TCM level (1-6) if the PM is of the type TCM. This will be 0 for OTUK/ODUK.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	0..6

jnxoptIfOTNPMCurrentSuspectedFlag		1.3.6.1.4.1.2636.3.73.1.3.3.3.1.4
If true, the data in this entry may be unreliable.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

jnxoptIfOTNPMCurrentBip8		1.3.6.1.4.1.2636.3.73.1.3.3.3.1.5
Number of Failures occurred in an observation period.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMCurrentESs		1.3.6.1.4.1.2636.3.73.1.3.3.3.1.6
This is the number of seconds in which one or more bits are in error or during which Loss of Signal (LOS) or Alarm Indication Signal (AIS) is detected.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMCurrentSESs		1.3.6.1.4.1.2636.3.73.1.3.3.3.1.7
The number of seconds which have a severe error. This is the number of seconds in which the bit-error ratio = 1x10Eminus3 or during which Loss of Signal (LOS) or Alarm Indication Signal (AIS) is detected.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMCurrentUASs		1.3.6.1.4.1.2636.3.73.1.3.3.3.1.8
It is the number of unavailable seconds. A period of unavailable time begins at the onset of ten consecutive SES events. These ten seconds are considered to be part of unavailable time. A new period of available time begins at the onset of ten consecutive non-SES events. These ten seconds are considered to be part of available time.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMCurrentBBEs		1.3.6.1.4.1.2636.3.73.1.3.3.3.1.9
An errored block not occurring as part of an SES.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMCurrentESR		1.3.6.1.4.1.2636.3.73.1.3.3.3.1.10
The ratio of ES in available time to total seconds in available time during a fixed measurement interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMCurrentSESR		1.3.6.1.4.1.2636.3.73.1.3.3.3.1.11
The ratio of SES in available time to total seconds in available time during a fixed measurement interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMCurrentBBER		1.3.6.1.4.1.2636.3.73.1.3.3.3.1.12
The ratio of BER in available time to total seconds in available time during a fixed measurement interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMCurrentElapsedTime		1.3.6.1.4.1.2636.3.73.1.3.3.3.1.13
Time elapsed for this 15 minute interval
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMCurSuspectReason		1.3.6.1.4.1.2636.3.73.1.3.3.3.1.14
If SuspectedFlag is true, the reson for the PM data being suspect. 0 - not applicable 1 - unknown 2 - new object 3 - interface disabled 4 - clock shift detected 5 - cleared by user 6 - interval too short secs < 890 7 - interval too long secs > 910 8 - near end unavailable 9 - far end unavailable 10 - partial data 11 - missing intervals due to restarts
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

jnxoptIfOTNPMIntervalTable		1.3.6.1.4.1.2636.3.73.1.3.3.4
A Performance monitoring Interval Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		JnxoptIfOTNPMIntervalEntry

jnxoptIfOTNPMIntervalEntry		1.3.6.1.4.1.2636.3.73.1.3.3.4.1
A conceptual entry in the Near end or Far End performance monitoring Interval table for the type 'jnxoptIfOTNPMIntervalLayer' layer.
Status: current	Access: not-accessible
OBJECT-TYPE
	JnxoptIfOTNPMIntervalEntry

jnxoptIfOTNPMIntervalType		1.3.6.1.4.1.2636.3.73.1.3.3.4.1.1
This parameter indicates the parameters for the table are for the Near End or Far End performance data. 1 - Near End 2 - Far End
Status: current	Access: not-accessible
OBJECT-TYPE
	JnxoptIfOTNType

jnxoptIfOTNPMIntervalLayer		1.3.6.1.4.1.2636.3.73.1.3.3.4.1.2
This parameter indicates the parameters for the table are for OTUk, ODUk, TCMn performance data. 1 - OTUk 2 - ODUk 3 - TCM The ODUk/TCM sublayer PM is not related to the black link PM management, but since this is a common PM model for the ODU/TCM layer, we may include it here.
Status: current	Access: not-accessible
OBJECT-TYPE
	JnxoptIfOTNLayer

jnxoptIfOTNPMIntervalTCMLevel		1.3.6.1.4.1.2636.3.73.1.3.3.4.1.3
This parameter indicates the TCM level (1-6) if the PM is of the type TCM. This will be 0 for OTUK/ODUK.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	0..6

jnxoptIfOTNPMIntervalNumber		1.3.6.1.4.1.2636.3.73.1.3.3.4.1.4
A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the 15 minutes interval completed 23 hours and 45 minutes prior to interval 1.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..96

jnxoptIfOTNPMIntervalSuspectedFlag		1.3.6.1.4.1.2636.3.73.1.3.3.4.1.5
If true, the data in this entry may be unreliable.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

jnxoptIfOTNPMIntervalBip8		1.3.6.1.4.1.2636.3.73.1.3.3.4.1.6
Number of Failures occurred in an observation period.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMIntervalESs		1.3.6.1.4.1.2636.3.73.1.3.3.4.1.7
It is a one-second period in which one or more bits are in error or during which Loss of Signal (LOS) or Alarm Indication Signal (AIS) is detected.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMIntervalSESs		1.3.6.1.4.1.2636.3.73.1.3.3.4.1.8
The number of seconds which have a severe error. It is a one-second period which has a bit-error ratio = 1x10Eminus3 or during which Loss of Signal (LOS) or Alarm Indication Signal (AIS) is detected.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMIntervalUASs		1.3.6.1.4.1.2636.3.73.1.3.3.4.1.9
It is the number of unavailable seconds in this 15 minute interval. A period of unavailable time begins at the onset of ten consecutive SES events. These ten seconds are considered to be part of unavailable time. A new period of available time begins at the onset of ten consecutive non-SES events. These ten seconds are considered to be part of available time.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMIntervalBBEs		1.3.6.1.4.1.2636.3.73.1.3.3.4.1.10
An errored block not occurring as part of an SES.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMIntervalESR		1.3.6.1.4.1.2636.3.73.1.3.3.4.1.11
The ratio of ES in available time to total seconds in available time during a fixed measurement interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMIntervalSESR		1.3.6.1.4.1.2636.3.73.1.3.3.4.1.12
The ratio of SES in available time to total seconds in available time during a fixed measurement interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMIntervalBBER		1.3.6.1.4.1.2636.3.73.1.3.3.4.1.13
The ratio of BBE in available time to total seconds in available time during a fixed measurement interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMIntervalTimeStamp		1.3.6.1.4.1.2636.3.73.1.3.3.4.1.14
Time stamp of this interval.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

jnxoptIfOTNPMIntSuspectReason		1.3.6.1.4.1.2636.3.73.1.3.3.4.1.15
If SuspectedFlag is true, the reson for the PM data being suspect. 0 - not applicable 1 - unknown 2 - new object 3 - interface disabled 4 - clock shift detected 5 - cleared by user 6 - interval too short secs < 890 7 - interval too long secs > 910 8 - near end unavailable 9 - far end unavailable 10 - partial data 11 - missing intervals due to restarts
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

jnxoptIfOTNPMCurrentDayTable		1.3.6.1.4.1.2636.3.73.1.3.3.5
A Performance monitoring Current Day Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		JnxoptIfOTNPMCurrentDayEntry

jnxoptIfOTNPMCurrentDayEntry		1.3.6.1.4.1.2636.3.73.1.3.3.5.1
A conceptual entry in the Near end or Far End performance monitoring Current day table for the type 'jnxoptIfOTNPMCurrentDayLayer' layer.
Status: current	Access: not-accessible
OBJECT-TYPE
	JnxoptIfOTNPMCurrentDayEntry

jnxoptIfOTNPMCurrentDayType		1.3.6.1.4.1.2636.3.73.1.3.3.5.1.1
This parameter indicates the parameters for the table are for the Near End or Far End performance data. 1 - Near End 2 - Far End
Status: current	Access: not-accessible
OBJECT-TYPE
	JnxoptIfOTNType

jnxoptIfOTNPMCurrentDayLayer		1.3.6.1.4.1.2636.3.73.1.3.3.5.1.2
This parameter indicates the parameters for the table are for OTUk, ODUk, TCMn performance data. 1 - OTUk 2 - ODUk 3 - TCM The ODUk/TCM sublayer PM is not related to the black link PM management, but since this is a common PM model for the ODU/TCM layer, we may include it here.
Status: current	Access: not-accessible
OBJECT-TYPE
	JnxoptIfOTNLayer

jnxoptIfOTNPMCurrentDayTCMLevel		1.3.6.1.4.1.2636.3.73.1.3.3.5.1.3
This parameter indicates the TCM level (1-6) if the PM is of the type TCM. This will be 0 for OTUK/ODUK.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	0..6

jnxoptIfOTNPMCurrentDaySuspectedFlag		1.3.6.1.4.1.2636.3.73.1.3.3.5.1.4
If true, the data in this entry may be unreliable.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

jnxoptIfOTNPMCurrentDayBip8		1.3.6.1.4.1.2636.3.73.1.3.3.5.1.5
Number of Failures occurred in an observation period.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMCurrentDayESs		1.3.6.1.4.1.2636.3.73.1.3.3.5.1.6
The number of seconds which have an error. It is a one-second period in which one or more bits are in error or during which Loss of Signal (LOS) or Alarm Indication Signal (AIS) is detected.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMCurrentDaySESs		1.3.6.1.4.1.2636.3.73.1.3.3.5.1.7
The number of seconds which have a severe error. It is a one-second period which has a bit-error ratio = 1x10Eminus3 or during which Loss of Signal (LOS) or Alarm Indication Signal (AIS) is detected.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMCurrentDayUASs		1.3.6.1.4.1.2636.3.73.1.3.3.5.1.8
It is the number of unavailable seconds in the cunrrent day. A period of unavailable time begins at the onset of ten consecutive SES events. These ten seconds are considered to be part of unavailable time. A new period of available time begins at the onset of ten consecutive non-SES events. These ten seconds are considered to be part of available time.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMCurrentDayBBEs		1.3.6.1.4.1.2636.3.73.1.3.3.5.1.9
An errored block not occurring as part of an SES.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMCurrentDayESR		1.3.6.1.4.1.2636.3.73.1.3.3.5.1.10
The ratio of ES in available time to total seconds in available time during a fixed measurement interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMCurrentDaySESR		1.3.6.1.4.1.2636.3.73.1.3.3.5.1.11
The ratio of SES in available time to total seconds in available time during a fixed measurement interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMCurrentDayBBER		1.3.6.1.4.1.2636.3.73.1.3.3.5.1.12
The ratio of BBE in available time to total seconds in available time during a fixed measurement interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMCurrentDayElapsedTime		1.3.6.1.4.1.2636.3.73.1.3.3.5.1.13
Time elapsed for current day
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMCurDaySuspectReason		1.3.6.1.4.1.2636.3.73.1.3.3.5.1.14
If SuspectedFlag is true, the reson for the PM data being suspect. 0 - not applicable 1 - unknown 2 - new object 3 - interface disabled 4 - clock shift detected 5 - cleared by user 6 - partial data 7 - one or more intervals are invaild
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

jnxoptIfOTNPMPrevDayTable		1.3.6.1.4.1.2636.3.73.1.3.3.6
A Performance monitoring Previous Day Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		JnxoptIfOTNPMPrevDayEntry

jnxoptIfOTNPMPrevDayEntry		1.3.6.1.4.1.2636.3.73.1.3.3.6.1
A conceptual entry in the Near end or Far End performance monitoring previous day table for the type 'jnxoptIfOTNPMPrevDayLayer' layer.
Status: current	Access: not-accessible
OBJECT-TYPE
	JnxoptIfOTNPMPrevDayEntry

jnxoptIfOTNPMPrevDayType		1.3.6.1.4.1.2636.3.73.1.3.3.6.1.1
This parameter indicates the parameters for the table are for the Near End or Far End performance data. 1 - Near End 2 - Far End
Status: current	Access: not-accessible
OBJECT-TYPE
	JnxoptIfOTNType

jnxoptIfOTNPMPrevDayLayer		1.3.6.1.4.1.2636.3.73.1.3.3.6.1.2
This parameter indicates the parameters for the table are for OTUk, ODUk, TCMn performance data. 1 - OTUk 2 - ODUk 3 - TCM The ODUk/TCM sublayer PM is not related to the black link PM management, but since this is a common PM model for the ODU/TCM layer, we may include it here.
Status: current	Access: not-accessible
OBJECT-TYPE
	JnxoptIfOTNLayer

jnxoptIfOTNPMPrevDayTCMLevel		1.3.6.1.4.1.2636.3.73.1.3.3.6.1.3
This parameter indicates the TCM level (1-6) if the PM is of the type TCM.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	0..6

jnxoptIfOTNPMPrevDaySuspectedFlag		1.3.6.1.4.1.2636.3.73.1.3.3.6.1.4
If true, the data in this entry may be unreliable.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

jnxoptIfOTNPMPrevDayBip8		1.3.6.1.4.1.2636.3.73.1.3.3.6.1.5
Number of pre FEC failures occurred in an observation period.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMPrevDayESs		1.3.6.1.4.1.2636.3.73.1.3.3.6.1.6
The number of seconds which have an error. It is a one-second period in which one or more bits are in error or during which Loss of Signal (LOS) or Alarm Indication Signal (AIS) is detected.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMPrevDaySESs		1.3.6.1.4.1.2636.3.73.1.3.3.6.1.7
The number of seconds which have a severe error. A severely errored second, is a one-second period which has a bit-error ratio = 1x10Eminus3 or during which Loss of Signal (LOS) or Alarm Indication Signal (AIS) is detected.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMPrevDayUASs		1.3.6.1.4.1.2636.3.73.1.3.3.6.1.8
It is the number of unavailable seconds in the previous day. A period of unavailable time begins at the onset of ten consecutive SES events. These ten seconds are considered to be part of unavailable time. A new period of available time begins at the onset of ten consecutive non-SES events. These ten seconds are considered to be part of available time.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMPrevDayBBEs		1.3.6.1.4.1.2636.3.73.1.3.3.6.1.9
An errored block not occurring as part of an SES.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMPrevDayESR		1.3.6.1.4.1.2636.3.73.1.3.3.6.1.10
The ratio of ES in available time to total seconds in available time during a fixed measurement interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMPrevDaySESR		1.3.6.1.4.1.2636.3.73.1.3.3.6.1.11
The ratio of SES in available time to total seconds in available time during a fixed measurement interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMPrevDayBBER		1.3.6.1.4.1.2636.3.73.1.3.3.6.1.12
The ratio of BBE in available time to total seconds in available time during a fixed measurement interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMPrevDayTimeStamp		1.3.6.1.4.1.2636.3.73.1.3.3.6.1.13
Time stamp of this interval.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

jnxoptIfOTNPMPrevDaySuspectReason		1.3.6.1.4.1.2636.3.73.1.3.3.6.1.14
If SuspectedFlag is true, the reson for the PM data being suspect. 0 - not applicable 1 - unknown 2 - new object 3 - clock shift detected 4 - cleared by user 5 - partial data 6 - missing intervals due to restarts 7 - one or more intervals are invaild
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

jnxoptIfOTNPMFECConfigTable		1.3.6.1.4.1.2636.3.73.1.3.3.7
A table of performance monitoring FEC configuration.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		JnxoptIfOTNPMFECConfigEntry

jnxoptIfOTNPMFECConfigEntry		1.3.6.1.4.1.2636.3.73.1.3.3.7.1
A conceptual entry in the performance monitoring FEC configuration layer.
Status: current	Access: not-accessible
OBJECT-TYPE
	JnxoptIfOTNPMFECConfigEntry

jnxoptIfOTNPMFECConfigType		1.3.6.1.4.1.2636.3.73.1.3.3.7.1.1
This parameter indicates the parameters for the table are for the Near End or Far End performance data. 1 - Near End 2 - Far End
Status: current	Access: not-accessible
OBJECT-TYPE
	JnxoptIfOTNType

jnxoptIfOTNPMFECValidIntervals		1.3.6.1.4.1.2636.3.73.1.3.3.7.1.2
The number of contiguous 15 minute intervals for which valid FEC PM data is available for the particular interface.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPM15MinPreFECBERMantissaThreshold		1.3.6.1.4.1.2636.3.73.1.3.3.7.1.3
BER (mantissa) by the interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send jnxoptIf15MinThreshPreFECBERTCA. One notification will be sent per interval per interface. A value of `0' will disable the notification.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPM15MinPreFECBERExponentThreshold		1.3.6.1.4.1.2636.3.73.1.3.3.7.1.4
The Pre FEC BER (exponent) by the interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send jnxoptIf15MinThreshPreFECBERTCA. One notification will be sent per interval per interface. A value of `0' will disable the notification.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPM24HourPreFECBERMantissaThreshold		1.3.6.1.4.1.2636.3.73.1.3.3.7.1.5
BER (mantissa) by the interface within any given 24 Hour performance data collection period, which causes the SNMP agent to send jnxoptIf5s24Hour15MinThreshPreFECBERTCA. One notification will be sent per 24 hour period per interface. A value of `0' will disable the notification.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPM24HourPreFECBERExponentThreshold		1.3.6.1.4.1.2636.3.73.1.3.3.7.1.6
The Pre FEC BER (exponent) by the interface within any given 24 Hour performance data collection period, which causes the SNMP agent to send jnxoptIf5s24Hour15MinThreshPreFECBERTCA. One notification will be sent per 24 hour period per interface. A value of `0' will disable the notification.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMFECBEREnableTCA		1.3.6.1.4.1.2636.3.73.1.3.3.7.1.7
Enable TCA's - 15minute and 24hr for FEC BER
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

jnxoptIfOTNPMFECCurrentTable		1.3.6.1.4.1.2636.3.73.1.3.3.8
A Performance monitoring FEC Current Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		JnxoptIfOTNPMFECCurrentEntry

jnxoptIfOTNPMFECCurrentEntry		1.3.6.1.4.1.2636.3.73.1.3.3.8.1
A conceptual entry in the Near end or Far End performance monitoring FEC current table.
Status: current	Access: not-accessible
OBJECT-TYPE
	JnxoptIfOTNPMFECCurrentEntry

jnxoptIfOTNPMFECCurrentType		1.3.6.1.4.1.2636.3.73.1.3.3.8.1.1
This parameter indicates the parameters for the table are for the Near End or Far End performance data. 1 - Near End 2 - Far End
Status: current	Access: not-accessible
OBJECT-TYPE
	JnxoptIfOTNType

jnxoptIfOTNPMFECCurrentSuspectedFlag		1.3.6.1.4.1.2636.3.73.1.3.3.8.1.2
If true, the data in this entry may be unreliable.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

jnxoptIfOTNPMCurrentFECCorrectedErr		1.3.6.1.4.1.2636.3.73.1.3.3.8.1.3
The number of bits corrected by the FEC are counted in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

jnxoptIfOTNPMCurrentFECUncorrectedWords		1.3.6.1.4.1.2636.3.73.1.3.3.8.1.4
The number of un-corrected words by the FEC are counted over the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

jnxoptIfOTNPMCurrentFECBERMantissa		1.3.6.1.4.1.2636.3.73.1.3.3.8.1.5
The number of Errored bits at receiving side before the FEC function counted over one second .. mantissa.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMCurrentFECBERExponent		1.3.6.1.4.1.2636.3.73.1.3.3.8.1.6
The number of Errored bits at receiving side before the FEC function counted over one second .. exponent (eg -1).
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMCurrentFECMinBERMantissa		1.3.6.1.4.1.2636.3.73.1.3.3.8.1.7
The minimum number of Errored bits at receiving side before the FEC function counted over one second .. mantissa.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMCurrentFECMinBERExponent		1.3.6.1.4.1.2636.3.73.1.3.3.8.1.8
The minimum number of Errored bits at receiving side before the FEC function counted over one second .. exponent (eg -1).
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMCurrentFECMaxBERMantissa		1.3.6.1.4.1.2636.3.73.1.3.3.8.1.9
The maximum number of Errored bits at receiving side before the FEC function counted over one second .. mantissa.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMCurrentFECMaxBERExponent		1.3.6.1.4.1.2636.3.73.1.3.3.8.1.10
The maximum number of Errored bits at receiving side before the FEC function counted over one second .. exponent (eg -1).
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMCurrentFECAvgBERMantissa		1.3.6.1.4.1.2636.3.73.1.3.3.8.1.11
The average number of Errored bits at receiving side before the FEC function counted over one second .. mantissa.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMCurrentFECAvgBERExponent		1.3.6.1.4.1.2636.3.73.1.3.3.8.1.12
The average number of Errored bits at receiving side before the FEC function counted over one second .. exponent (eg -1).
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMCurrentFECElapsedTime		1.3.6.1.4.1.2636.3.73.1.3.3.8.1.13
Time elapsed for this 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMFECCurSuspectReason		1.3.6.1.4.1.2636.3.73.1.3.3.8.1.14
If SuspectedFlag is true, the reson for the PM data being suspect. 0 - not applicable 1 - unknown 2 - new object 3 - interface disabled 4 - clock shift detected 5 - cleared by user 6 - interval too short secs < 890 7 - interval too long secs > 910 8 - near end unavailable 9 - far end unavailable 10 - partial data 11 - missing intervals due to restarts
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

jnxoptIfOTNPMFECIntervalTable		1.3.6.1.4.1.2636.3.73.1.3.3.9
A Performance monitoring FEC Interval Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		JnxoptIfOTNPMFECIntervalEntry

jnxoptIfOTNPMFECIntervalEntry		1.3.6.1.4.1.2636.3.73.1.3.3.9.1
A conceptual entry in the Near end or Far End performance monitoring FEC interval table.
Status: current	Access: not-accessible
OBJECT-TYPE
	JnxoptIfOTNPMFECIntervalEntry

jnxoptIfOTNPMFECIntervalType		1.3.6.1.4.1.2636.3.73.1.3.3.9.1.1
This parameter indicates the parameters for the table are for the Near End or Far End performance data. 1 - Near End 2 - Far End
Status: current	Access: not-accessible
OBJECT-TYPE
	JnxoptIfOTNType

jnxoptIfOTNPMFECIntervalNumber		1.3.6.1.4.1.2636.3.73.1.3.3.9.1.2
A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the 15 minutes interval completed 23 hours and 45 minutes prior to interval 1.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMFECIntervalSuspectedFlag		1.3.6.1.4.1.2636.3.73.1.3.3.9.1.3
If true, the data in this entry may be unreliable.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

jnxoptIfOTNPMIntervalFECCorrectedErr		1.3.6.1.4.1.2636.3.73.1.3.3.9.1.4
The number of bits corrected by the FEC are counted in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

jnxoptIfOTNPMIntervalFECUncorrectedWords		1.3.6.1.4.1.2636.3.73.1.3.3.9.1.5
The number of words un-corrected words by the FEC are counted over the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

jnxoptIfOTNPMIntervalMinFECBERMantissa		1.3.6.1.4.1.2636.3.73.1.3.3.9.1.6
The minimun bit error rate at receiving side before the FEC function counted over one second .. mantissa. This is the minimum Pre FEC BER in the current 24hour period.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMIntervalMinFECBERExponent		1.3.6.1.4.1.2636.3.73.1.3.3.9.1.7
The minimun bit error rate at receiving side before the FEC function counted over one second .. exponent. This is the minimum Pre FEC BER in the current 24hour period.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMIntervalMaxFECBERMantissa		1.3.6.1.4.1.2636.3.73.1.3.3.9.1.8
The maximun bit error rate at receiving side before the FEC function counted over one second .. mantissa. This is the maximum Pre FEC BER in the current 24hour period.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMIntervalMaxFECBERExponent		1.3.6.1.4.1.2636.3.73.1.3.3.9.1.9
The maximun bit error rate at receiving side before the FEC function counted over one second .. exponent. This is the maximum Pre FEC BER in the current 24hour period.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMIntervalAvgFECBERMantissa		1.3.6.1.4.1.2636.3.73.1.3.3.9.1.10
The average bit error rate at receiving side before the FEC function counted over one second .. mantissa. This is the average Pre FEC BER in the current 24hour period.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMIntervalAvgFECBERExponent		1.3.6.1.4.1.2636.3.73.1.3.3.9.1.11
The average bit error rate at receiving side before the FEC function counted over one second .. exponent. This is the average Pre FEC BER in the current 24hour period.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMFECIntervalTimeStamp		1.3.6.1.4.1.2636.3.73.1.3.3.9.1.12
Time stamp of this interval.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

jnxoptIfOTNPMFECIntSuspectReason		1.3.6.1.4.1.2636.3.73.1.3.3.9.1.13
If SuspectedFlag is true, the reson for the PM data being suspect. 0 - not applicable 1 - unknown 2 - new object 3 - interface disabled 4 - clock shift detected 5 - cleared by user 6 - interval too short secs < 890 7 - interval too long secs > 910 8 - near end unavailable 9 - far end unavailable 10 - partial data 11 - missing intervals due to restarts
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

jnxoptIfOTNPMFECCurrentDayTable		1.3.6.1.4.1.2636.3.73.1.3.3.10
A Performance monitoring FEC current day table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		JnxoptIfOTNPMFECCurrentDayEntry

jnxoptIfOTNPMFECCurrentDayEntry		1.3.6.1.4.1.2636.3.73.1.3.3.10.1
A conceptual entry in the Near end or Far End performance monitoring FEC current day table.
Status: current	Access: not-accessible
OBJECT-TYPE
	JnxoptIfOTNPMFECCurrentDayEntry

jnxoptIfOTNPMFECCurrentDayType		1.3.6.1.4.1.2636.3.73.1.3.3.10.1.1
This parameter indicates the parameters for the table are for the Near End or Far End performance data. 1 - Near End 2 - Far End
Status: current	Access: not-accessible
OBJECT-TYPE
	JnxoptIfOTNType

jnxoptIfOTNPMFECCurrentDaySuspectedFlag		1.3.6.1.4.1.2636.3.73.1.3.3.10.1.2
If true, the data in this entry may be unreliable.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

jnxoptIfOTNPMCurrentDayFECCorrectedErr		1.3.6.1.4.1.2636.3.73.1.3.3.10.1.3
The number of bits corrected by the FEC are counted in the interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

jnxoptIfOTNPMCurrentDayFECUncorrectedWords		1.3.6.1.4.1.2636.3.73.1.3.3.10.1.4
The number of words un-corrected by the FEC are counted over the Day.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

jnxoptIfOTNPMCurrentDayMinFECBERMantissa		1.3.6.1.4.1.2636.3.73.1.3.3.10.1.5
The minimun bit error rate at receiving side before the FEC function counted over one second .. mantissa. This is the minimum PreFEC BER in the current 24hour period.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMCurrentDayMinFECBERExponent		1.3.6.1.4.1.2636.3.73.1.3.3.10.1.6
The minimun bit error rate at receiving side before the FEC function counted over one second .. exponent. This is the minimum PreFEC BER in the current 24hour period.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMCurrentDayMaxFECBERMantissa		1.3.6.1.4.1.2636.3.73.1.3.3.10.1.7
The maximun bit error rate at receiving side before the FEC function counted over one second .. mantissa. This is the maximum PreFEC BER in the current 24hour period.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMCurrentDayMaxFECBERExponent		1.3.6.1.4.1.2636.3.73.1.3.3.10.1.8
The maximun bit error rate at receiving side before the FEC function counted over one second .. exponent. This is the maximum PreFEC BER in the current 24hour period.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMCurrentDayAvgFECBERMantissa		1.3.6.1.4.1.2636.3.73.1.3.3.10.1.9
The average bit error rate at receiving side before the FEC function counted over one second .. mantissa. This is the average PreFEC BER in the current 24hour period.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMCurrentDayAvgFECBERExponent		1.3.6.1.4.1.2636.3.73.1.3.3.10.1.10
The average bit error rate at receiving side before the FEC function counted over one second .. exponent. This is the average PreFEC BER in the current 24hour period.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMFECCurrentDayElapsedTime		1.3.6.1.4.1.2636.3.73.1.3.3.10.1.11
Time elapsed for current day.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMFECCurDaySuspectReason		1.3.6.1.4.1.2636.3.73.1.3.3.10.1.12
If SuspectedFlag is true, the reson for the PM data being suspect. 0 - not applicable 1 - unknown 2 - new object 3 - clock shift detected 4 - cleared by user 5 - partial data 6 - missing intervals due to restarts 7 - one or more intervals are invaild
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

jnxoptIfOTNPMFECPrevDayTable		1.3.6.1.4.1.2636.3.73.1.3.3.11
A Performance monitoring FEC previous day table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		JnxoptIfOTNPMFECPrevDayEntry

jnxoptIfOTNPMFECPrevDayEntry		1.3.6.1.4.1.2636.3.73.1.3.3.11.1
A conceptual entry in the Near end or Far End performance monitoring FEC previous day table.
Status: current	Access: not-accessible
OBJECT-TYPE
	JnxoptIfOTNPMFECPrevDayEntry

jnxoptIfOTNPMFECPrevDayType		1.3.6.1.4.1.2636.3.73.1.3.3.11.1.1
This parameter indicates the parameters for the table are for the Near End or Far End performance data. 1 - Near End 2 - Far End
Status: current	Access: not-accessible
OBJECT-TYPE
	JnxoptIfOTNType

jnxoptIfOTNPMFECPrevDaySuspectedFlag		1.3.6.1.4.1.2636.3.73.1.3.3.11.1.2
If true, the data in this entry may be unreliable.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

jnxoptIfOTNPMPrevDayFECCorrectedErr		1.3.6.1.4.1.2636.3.73.1.3.3.11.1.3
The number of bits corrected by the FEC are counted in the previous day.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

jnxoptIfOTNPMPrevDayFECUncorrectedWords		1.3.6.1.4.1.2636.3.73.1.3.3.11.1.4
The number of un-corrected words by the FEC are counted over the previous Day.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

jnxoptIfOTNPMPrevDayMinFECBERMantissa		1.3.6.1.4.1.2636.3.73.1.3.3.11.1.5
The maximun bit error rate at receiving side before the FEC function counted over one second .. mantissa. This is the maximum Pre FEC BER in the previous 24hour period.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMPrevDayMinFECBERExponent		1.3.6.1.4.1.2636.3.73.1.3.3.11.1.6
The minimun bit error rate at receiving side before the FEC function counted over one second .. exponent. This is the maximum Pre FEC BER in the previous 24hour period.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMPrevDayMaxFECBERMantissa		1.3.6.1.4.1.2636.3.73.1.3.3.11.1.7
The maximun bit error rate at receiving side before the FEC function counted over one second .. mantissa. This is the maximum Pre FEC BER in the previous 24hour period (mantissa).
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMPrevDayMaxFECBERExponent		1.3.6.1.4.1.2636.3.73.1.3.3.11.1.8
The maximun bit error rate at receiving side before the FEC function counted over one second .. exponent (eg -3). This is the maximum Pre FEC BER in the previous 24hour period.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMPrevDayAvgFECBERMantissa		1.3.6.1.4.1.2636.3.73.1.3.3.11.1.9
The average bit error rate at receiving side before the FEC function counted over one second .. mantissa. This is the average Pre FEC BER during the previous 24hour period (mantissa).
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMPrevDayAvgFECBERExponent		1.3.6.1.4.1.2636.3.73.1.3.3.11.1.10
The average bit error rate at receiving side before the FEC function counted over one second .. exponent (eg -3). This is the average Pre FEC BER during the previous 24hour period.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNPMFECPrevDayTimeStamp		1.3.6.1.4.1.2636.3.73.1.3.3.11.1.11
Time stamp for the Prev day.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

jnxoptIfOTNPMFECPrevDaySuspectReason		1.3.6.1.4.1.2636.3.73.1.3.3.11.1.12
If SuspectedFlag is true, the reson for the PM data being suspect. 0 - not applicable 1 - unknown 2 - new object 3 - clock shift detected 4 - cleared by user 5 - partial data 6 - missing intervals due to restarts 7 - one or more intervals are invaild
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

jnxoptIfOTNAlarmTable		1.3.6.1.4.1.2636.3.73.1.3.4.1
A table of alarm entries.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		JnxoptIfOTNAlarmEntry

jnxoptIfOTNAlarmEntry		1.3.6.1.4.1.2636.3.73.1.3.4.1.1
A conceptual entry in the alarm table.
Status: current	Access: not-accessible
OBJECT-TYPE
	JnxoptIfOTNAlarmEntry

jnxoptIfOTNAlarmLocation		1.3.6.1.4.1.2636.3.73.1.3.4.1.1.1
The object identifies indicates if this entry was for Near end/Far end.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	JnxoptIfOTNType

jnxoptIfOTNAlarmDirection		1.3.6.1.4.1.2636.3.73.1.3.4.1.1.2
The object identifies indicates if this entry was for for the Tx/Rx or both.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	JnxoptIfOTNDirection

jnxoptIfOTNAlarmLayer		1.3.6.1.4.1.2636.3.73.1.3.4.1.1.3
This specifies which sublayer this alarm is for.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	JnxoptIfOTNLayer

jnxoptIfOTNAlarmTCMLevel		1.3.6.1.4.1.2636.3.73.1.3.4.1.1.4
TCM level 1-6 of the alarm. It will be 0 if alarm sublayer is OCh, OTUk or ODUk.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Unsigned32

jnxoptIfOTNOChOTUkAlarmType		1.3.6.1.4.1.2636.3.73.1.3.4.1.1.5
This specifies the type of alarm of the sublayer 'jnxoptIfOTNAlarmLayer' for OCh/OTUk .
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	JnxoptIfOTNOChAlarms

jnxoptIfOTNAlarmSeverity		1.3.6.1.4.1.2636.3.73.1.3.4.1.1.6
The object identifies the severity of the last alarm/alert that most recently was set or cleared.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	JnxoptIfOTNAlarmSeverity

jnxoptIfOTNAlarmDate		1.3.6.1.4.1.2636.3.73.1.3.4.1.1.7
This specifies the date and time when this alarm occurred.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DateAndTime

jnxoptIfOTNODUkTcmAlarmType		1.3.6.1.4.1.2636.3.73.1.3.4.1.1.8
This specifies the type of alarm of the sublayer 'jnxoptIfOTNAlarmLayer' for ODUk/TCM .
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	JnxoptIfOTNODUkTcmAlarms

jnxoptIfOTNOChOTUkAlarmSet		1.3.6.1.4.1.2636.3.73.1.3.0.1
Notification of a recently set OTN alarm of Layer and Type.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

jnxoptIfOTNOChOTUkAlarmClear		1.3.6.1.4.1.2636.3.73.1.3.0.2
Notification of a recently clear OTN alarm of Layer and Type.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

jnxoptIfOTNODUkTcmAlarmSet		1.3.6.1.4.1.2636.3.73.1.3.0.3
Notification of a recently set OTN alarm of Layer and Type.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

jnxoptIfOTNODUkTcmAlarmClear		1.3.6.1.4.1.2636.3.73.1.3.0.4
Notification of a recently clear OTN alarm of Layer and Type.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE