IRM3-MIB

File: IRM3-MIB.mib (98393 bytes)

Imported modules

RFC1155-SMI IRM-OIDS RFC1213-MIB
RFC-1212

Imported symbols

NetworkAddress Counter repeaterRev1
repeaterRev2 subSysMMAC DisplayString
OBJECT-TYPE

Defined Values

device 1.3.6.1.4.1.52.1.2.1.1
OBJECT IDENTIFIER    

board 1.3.6.1.4.1.52.1.2.1.2
OBJECT IDENTIFIER    

port 1.3.6.1.4.1.52.1.2.1.3
OBJECT IDENTIFIER    

sourceAddr 1.3.6.1.4.1.52.1.2.1.7
OBJECT IDENTIFIER    

redundancy 1.3.6.1.4.1.52.1.2.1.8
OBJECT IDENTIFIER    

alarm 1.3.6.1.4.1.52.1.2.1.9
OBJECT IDENTIFIER    

deviceMMACType 1.3.6.1.4.1.52.1.2.1.1.2
Indicates the type of MMAC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER unknown(1), mMAC8(2), mMAC5(3), mMAC3(4), mINIMMAC(5), mRXI(6), m3Shunt(7), m5Shunt(8), m8FNB(9), nonFNB(10), mMAC3Shunting(11), mMAC5Shunting(12), mMAC8Shunting(13), m8Shunting(14)  

deviceSlots 1.3.6.1.4.1.52.1.2.1.1.3
Number of available device slots in this device, including the IRM slot.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

deviceOccupiedSlots 1.3.6.1.4.1.52.1.2.1.1.4
The slots that contain MIM boards. This field is bit encoded (eg. if a bit is set then that board is present). For example, a value of 3 indicates that there are boards in the IRM slot and the first MIM slot.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

devicePortsOn 1.3.6.1.4.1.52.1.2.1.1.5
The number of operating ports on the device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

deviceTotalPorts 1.3.6.1.4.1.52.1.2.1.1.6
The total number of repeater ports on the MMAC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

deviceTotalPkts 1.3.6.1.4.1.52.1.2.1.1.7
The number of packets detected on all ports of this device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

deviceTotalErrors 1.3.6.1.4.1.52.1.2.1.1.8
The sum of all of the errors listed including alignment, CRC, runts, giants, and out of window collisions.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

deviceTransmitColls 1.3.6.1.4.1.52.1.2.1.1.9
The number of transmit collisions detected by this MMAC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

deviceRecColls 1.3.6.1.4.1.52.1.2.1.1.10
The number of receive collisions detected by this MMAC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

deviceAlignErrs 1.3.6.1.4.1.52.1.2.1.1.11
The number of packets with alignment errors detected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

deviceCRCErrs 1.3.6.1.4.1.52.1.2.1.1.12
The number of packets with bad CRC detected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

deviceRunts 1.3.6.1.4.1.52.1.2.1.1.13
The number of runt frames detected by this device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

deviceOOWColls 1.3.6.1.4.1.52.1.2.1.1.14
The number of out-of-window collisions detected by this device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

deviceNoResources 1.3.6.1.4.1.52.1.2.1.1.15
The number of No resource condtions detected by this device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

deviceRecBytes 1.3.6.1.4.1.52.1.2.1.1.16
The number of bytes detected on the network.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

deviceGiantFrames 1.3.6.1.4.1.52.1.2.1.1.17
The number of packets longer than 1518 bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

deviceRestart 1.3.6.1.4.1.52.1.2.1.1.18
If this object is set to 1 the device is restarted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

deviceResetCounters 1.3.6.1.4.1.52.1.2.1.1.19
If this object is set to 1, all of the devices counters are reset to 0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

deviceRedundantCts 1.3.6.1.4.1.52.1.2.1.1.20
The number of redundant circuits available for use.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

deviceDiscover 1.3.6.1.4.1.52.1.2.1.1.21
When this variable is set to 1 The following events occur: (1) The device sends a LINK-UP trap (2) The device sends a proprietary packet that will cause all other Cabeltron devices on that local network to send a LINK-UP trap.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER  

deviceTimeBase 1.3.6.1.4.1.52.1.2.1.1.24
The number of seconds used as the interval for performing all of the rate alarm checks. The minimum is 10 secs.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

deviceResetRedundancy 1.3.6.1.4.1.52.1.2.1.1.25
Setting this object to a 1 will reset redundancy for the entire box.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

deviceSrcAddrAgingTime 1.3.6.1.4.1.52.1.2.1.1.26
The number of minutes that a source address is not detected before it is removed from the source address table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

deviceSrcAddrTraps 1.3.6.1.4.1.52.1.2.1.1.27
Controls sending of source address related traps.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER trapsOff(1), trapsOn(2)  

deviceSrcAddrLocked 1.3.6.1.4.1.52.1.2.1.1.28
If this is set to 2, any source addresses that are detected on station ports that are not in the table will cause the port to be turned off.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER lockOff(1), lockOn(2)  

deviceEtherOccupiedSlots 1.3.6.1.4.1.52.1.2.1.1.29
The slots that contain Ethernet MIM boards. This field is bit encoded (eg. if a bit is set then that board is present). For example, a value of 2 indicates that there is an Ethernet board in the first MIM slot.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

deviceTROccupiedSlots 1.3.6.1.4.1.52.1.2.1.1.30
The slots that contain managable Token Ring MIM boards. This field is bit encoded (eg. if a bit is set then that board is present). For example, a value of 2 indicates that there is a managable Token Ring board in the first MIM slot.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

deviceFDDIOccupiedSlots 1.3.6.1.4.1.52.1.2.1.1.31
The slots that contain FDDI MIM boards. This field is bit encoded (eg. if a bit is set then that board is present). For example, a value of 2 indicates that there is an FDDI board in the first MIM slot.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

deviceRestoreDefaults 1.3.6.1.4.1.52.1.2.1.1.32
If this object is set to 1 the factory defaults are restored. This, however, does not affect the device's IP address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

deviceActiveUsers 1.3.6.1.4.1.52.1.2.1.1.33
The number of active users seen by this device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

deviceOSIFrames 1.3.6.1.4.1.52.1.2.1.1.34
The number of frames with OSI protocol seen by this device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

deviceNovellFrames 1.3.6.1.4.1.52.1.2.1.1.35
The number of frames with NOVELL protocol seen by this device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

deviceBanyanFrames 1.3.6.1.4.1.52.1.2.1.1.36
The number of frames with BANYAN protocol seen by this device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

deviceDECNetFrames 1.3.6.1.4.1.52.1.2.1.1.37
The number of frames with DECNET protocol seen by this device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

deviceXNSFrames 1.3.6.1.4.1.52.1.2.1.1.38
The number of frames with XNS protocol seen by this device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

deviceIPFrames 1.3.6.1.4.1.52.1.2.1.1.39
The number of frames with TCPIP protocol seen by this device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

deviceCtronFrames 1.3.6.1.4.1.52.1.2.1.1.40
The number of frames with Cabletron protocol seen by this device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

deviceAppletalkFrames 1.3.6.1.4.1.52.1.2.1.1.41
The number of frames with Appletalk protocol seen by this device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

deviceOtherFrames 1.3.6.1.4.1.52.1.2.1.1.42
The number of frames seen by this device, that do not fall into any of the previously listed protocol catagories.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

device64To127Frames 1.3.6.1.4.1.52.1.2.1.1.43
The number of frames seen by this device, with frame sizes between 64 and 127 bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

device128To255Frames 1.3.6.1.4.1.52.1.2.1.1.44
The number of frames seen by this device, with frame sizes between 128 and 255 bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

device256To511Frames 1.3.6.1.4.1.52.1.2.1.1.45
The number of frames seen by this device, with frame sizes between 256 and 511 bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

device512To1023Frames 1.3.6.1.4.1.52.1.2.1.1.46
The number of frames seen by this device, with frame sizes between 512 and 1023 bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

device1024To1518Frames 1.3.6.1.4.1.52.1.2.1.1.47
The number of frames seen by this device, with frame sizes between 1024 and 1518 bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

deviceBroadPkts 1.3.6.1.4.1.52.1.2.1.1.48
The sum of broadcast packets detected on all ports of this device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

deviceMultPkts 1.3.6.1.4.1.52.1.2.1.1.49
The sum of multicast packets detected on all ports of this device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

deviceThdPartyOccupiedSlots 1.3.6.1.4.1.52.1.2.1.1.51
The slots that contain Third Party MIM boards. This field is bit encoded (eg. if a bit is set then that board is present). For example, a value of 2 indicates that there is a Third Party board in the first MIM slot.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

deviceImimOccupiedSlots 1.3.6.1.4.1.52.1.2.1.1.52
The slots that contain Cabletron Intelligent MIM boards. This field is bit encoded (eg. if a bit is set then that board is present). For example, a value of 2 indicates that there is an Intelligent board in the first MIM slot.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

deviceLinkTraps 1.3.6.1.4.1.52.1.2.1.1.54
Controls sending of link related traps.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER trapsOff(1), trapsOn(2)  

ctIPDefaultFrameType 1.3.6.1.4.1.52.1.2.1.1.56
Defines the default frame type that will be used by the device. A device will understand both frame types and will respond based upon the framing type that is learned for the given address. This object defines the type of framing that will be used if no framing is known, for example ARP requests. Setting a value of 8022snap(2) will result in framing 802.3 - 802.2 - IP packets being generated by default. Setting a value of ethernet(1) will result in framing ethernet IP packets by default.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ethernet(1), snap8022(2)  

deviceSrcAddrType 1.3.6.1.4.1.52.1.2.1.1.57
Selects the hashing algorithm of source addresses, DEC or IP
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ipHash(1), decHash(2)  

sourceAddrBoard 1.3.6.1.4.1.52.1.2.1.7.1
The board number of the port that the supplied source address has been found on.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sourceAddrPort 1.3.6.1.4.1.52.1.2.1.7.2
The port number of the port that the supplied source address has been found on.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

redundancyPollInterval 1.3.6.1.4.1.52.1.2.1.8.1
The number of seconds between polls for redundancy.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

redundancyTestTod 1.3.6.1.4.1.52.1.2.1.8.2
The time of day at which the redundant circuits should be tested.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

redundancyPerformTest 1.3.6.1.4.1.52.1.2.1.8.3
Test the redundant circuit.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER performTest(1)  

redundancyCircuitName 1.3.6.1.4.1.52.1.2.1.8.4
The name of the indicated circuit.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

redundancyRetryCount 1.3.6.1.4.1.52.1.2.1.8.5
The number of unanswered polls allowed for the indicated circuit before the current connection is declared bad.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

redundancyNumBPs 1.3.6.1.4.1.52.1.2.1.8.6
The number of board/port combinations associated with the indicated circuit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

redundancyCircuitBoard 1.3.6.1.4.1.52.1.2.1.8.7
The boards associated with the indicated circuit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

redundancyCircuitPort 1.3.6.1.4.1.52.1.2.1.8.8
The ports associated with the indicated circuit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

redundancyCircuitTypes 1.3.6.1.4.1.52.1.2.1.8.9
The type of each port associated with the indicated circuit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

redundancyCircuitNumAddr 1.3.6.1.4.1.52.1.2.1.8.10
The number of addresses associated with the indicated circuit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

redundancyCircuitMACAddrAdd 1.3.6.1.4.1.52.1.2.1.8.11
Adds this ethernet address to the polling list for the indicated circuit.
Status: mandatory Access: read-write
OBJECT-TYPE    
  NetworkAddress  

redundancyCircuitMACAddrDel 1.3.6.1.4.1.52.1.2.1.8.12
Removes this ethernet address from the polling list for the indicated circuit.
Status: mandatory Access: read-write
OBJECT-TYPE    
  NetworkAddress  

redundancyCircuitMACAddrDisp 1.3.6.1.4.1.52.1.2.1.8.13
The ethernet addresses associated with the indicated circuit, accessed by index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NetworkAddress  

redundancyCircuitEnable 1.3.6.1.4.1.52.1.2.1.8.14
Enables and disables the indicated circuit.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

redundancyCircuitReset 1.3.6.1.4.1.52.1.2.1.8.15
Reset the indicated circuit. Return all of the associated board and ports to NOT-USED, remove associated addresses from the polling list, reset the circuit name and retry count to default values.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER reset(1)  

devAlrm 1.3.6.1.4.1.52.1.2.1.9.1
OBJECT IDENTIFIER    

bdAlrm 1.3.6.1.4.1.52.1.2.1.9.2
OBJECT IDENTIFIER    

portAlrm 1.3.6.1.4.1.52.1.2.1.9.3
OBJECT IDENTIFIER    

devTraffic 1.3.6.1.4.1.52.1.2.1.9.1.1
OBJECT IDENTIFIER    

devColls 1.3.6.1.4.1.52.1.2.1.9.1.2
OBJECT IDENTIFIER    

devError 1.3.6.1.4.1.52.1.2.1.9.1.3
OBJECT IDENTIFIER    

devBroad 1.3.6.1.4.1.52.1.2.1.9.1.4
OBJECT IDENTIFIER    

devTrafficEnable 1.3.6.1.4.1.52.1.2.1.9.1.1.1
Enable the sending of device level traffic traps.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

devTrafficThreshold 1.3.6.1.4.1.52.1.2.1.9.1.1.2
The threshold of packets within the Devicetimebase that will cause a traffic alarm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

devCollsEnable 1.3.6.1.4.1.52.1.2.1.9.1.2.1
Enable the sending of device level collision alarms.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

devCollsThreshold 1.3.6.1.4.1.52.1.2.1.9.1.2.2
This object represents the number of collisions per good packet measured by the device that will generate an alarm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..15  

devErrorEnable 1.3.6.1.4.1.52.1.2.1.9.1.3.1
Enable the sending of device level error alarms.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

devErrorThreshold 1.3.6.1.4.1.52.1.2.1.9.1.3.2
This object represents the percentage of errors per good packet that will generate an alarm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

devErrorSource 1.3.6.1.4.1.52.1.2.1.9.1.3.3
The type of error used for the error alarm. The integer is a bit encoded version of which errors to include in the error sum. The bits are encoded as follows: CRCErrors - Bit 0 - Least Significant Bit runts - Bit 1 OOWColls - Bit 2 alignErrs - Bit 3 NoResource - Bit 4 Giants - Bit 5
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

devBroadEnable 1.3.6.1.4.1.52.1.2.1.9.1.4.1
Enable the sending of device level broadcast traps.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

devBroadThreshold 1.3.6.1.4.1.52.1.2.1.9.1.4.2
The threshold of broadcast packets within the Devicetimebase that will cause a broadcast alarm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

bdTraffic 1.3.6.1.4.1.52.1.2.1.9.2.1
OBJECT IDENTIFIER    

bdColls 1.3.6.1.4.1.52.1.2.1.9.2.2
OBJECT IDENTIFIER    

bdError 1.3.6.1.4.1.52.1.2.1.9.2.3
OBJECT IDENTIFIER    

bdBroad 1.3.6.1.4.1.52.1.2.1.9.2.4
OBJECT IDENTIFIER    

bdTrafficEnable 1.3.6.1.4.1.52.1.2.1.9.2.1.1
Enable the sending of board level traffic traps for this board.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

bdTrafficThreshold 1.3.6.1.4.1.52.1.2.1.9.2.1.2
The threshold of packets within the Devicetimebase that will cause a traffic alarm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

bdTrafficBdDisable 1.3.6.1.4.1.52.1.2.1.9.2.1.3
Permit a board to be disabled on a traffic threshold alarm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

bdCollsEnable 1.3.6.1.4.1.52.1.2.1.9.2.2.1
Enable the sending of board level collision alarms.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

bdCollsThreshold 1.3.6.1.4.1.52.1.2.1.9.2.2.2
This object represents the number of collisions per good packet measured by the board that will generate an alarm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..15  

bdCollsBdDisable 1.3.6.1.4.1.52.1.2.1.9.2.2.3
Permit a board to be disabled on a collision threshold alarm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

bdErrorEnable 1.3.6.1.4.1.52.1.2.1.9.2.3.1
Enable the sending of board level error alarms.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

bdErrorThreshold 1.3.6.1.4.1.52.1.2.1.9.2.3.2
This object represents the percentage of errors per good packet that will generate an alarm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

bdErrorSource 1.3.6.1.4.1.52.1.2.1.9.2.3.3
The type of error used for the error alarm. The integer is a bit encoded version of which errors to include in the error sum. The bits are encoded as follows: CRCErrors - Bit 0 Least Significant Bit runts - Bit 1 OOWColls - Bit 2 alignErrs - Bit 3 NoResource - Bit 4 Giants - Bit 5
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

bdErrorBdDisable 1.3.6.1.4.1.52.1.2.1.9.2.3.4
Permit a board to be disabled on an error threshold alarm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

bdBroadEnable 1.3.6.1.4.1.52.1.2.1.9.2.4.1
Enable the sending of board level broadcast traps for this board.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

bdBroadThreshold 1.3.6.1.4.1.52.1.2.1.9.2.4.2
The threshold of broadcast packets within the Devicetimebase that will cause a broadcast alarm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

bdBroadDisable 1.3.6.1.4.1.52.1.2.1.9.2.4.3
Permit a board to be disabled on a broadcast threshold alarm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

portTraffic 1.3.6.1.4.1.52.1.2.1.9.3.1
OBJECT IDENTIFIER    

portColls 1.3.6.1.4.1.52.1.2.1.9.3.2
OBJECT IDENTIFIER    

portError 1.3.6.1.4.1.52.1.2.1.9.3.3
OBJECT IDENTIFIER    

portBroad 1.3.6.1.4.1.52.1.2.1.9.3.4
OBJECT IDENTIFIER    

portTrafficEnable 1.3.6.1.4.1.52.1.2.1.9.3.1.1
Enable the sending of port level traffic traps for this port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

portTrafficThreshold 1.3.6.1.4.1.52.1.2.1.9.3.1.2
The threshold of packets within the Devicetimebase that will cause a traffic alarm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

portTrafficPortDisable 1.3.6.1.4.1.52.1.2.1.9.3.1.3
Permit a port to be disabled on a traffic threshold alarm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

portCollsEnable 1.3.6.1.4.1.52.1.2.1.9.3.2.1
Enable the sending of port level collsion alarms.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

portCollsThreshold 1.3.6.1.4.1.52.1.2.1.9.3.2.2
This object represents the number of collisions per good packet measured by the port that will generate an alarm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..15  

portCollsPortDisable 1.3.6.1.4.1.52.1.2.1.9.3.2.3
Permit a port to be disabled on a collision threshold alarm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

portErrorEnable 1.3.6.1.4.1.52.1.2.1.9.3.3.1
Enable the sending of port level error alarms.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

portErrorThreshold 1.3.6.1.4.1.52.1.2.1.9.3.3.2
This object represents the percentage of errors per good packet that will generate an alarm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

portErrorSource 1.3.6.1.4.1.52.1.2.1.9.3.3.3
The type of error used for the error alarm. The integer is a bit encoded version of which errors to include in the error sum. The bits are encoded as follows: CRCErrors - Bit 0 - Least Significant Bit runts - Bit 1 OOWColls - Bit 2 alignErrs - Bit 3 NoResource - Bit 4 Giants - Bit 5
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

portErrorPortDisable 1.3.6.1.4.1.52.1.2.1.9.3.3.4
Permit a port to be disabled on an error threshold alarm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

portBroadEnable 1.3.6.1.4.1.52.1.2.1.9.3.4.1
Enable the sending of port level broadcast alarms.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

portBroadThreshold 1.3.6.1.4.1.52.1.2.1.9.3.4.2
The threshold of broadcast packets within the Devicetimebase that will cause a broadcast alarm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

portBroadDisable 1.3.6.1.4.1.52.1.2.1.9.3.4.3
Permit a port to be disabled on a broadcast threshold alarm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

deviceR2 1.3.6.1.4.1.52.1.2.2.1
OBJECT IDENTIFIER    

networkR2 1.3.6.1.4.1.52.1.2.2.2
OBJECT IDENTIFIER    

boardR2 1.3.6.1.4.1.52.1.2.2.3
OBJECT IDENTIFIER    

portR2 1.3.6.1.4.1.52.1.2.2.4
OBJECT IDENTIFIER    

tokenRingD 1.3.6.1.4.1.52.1.2.2.1.3
OBJECT IDENTIFIER    

deviceTRPortsOn 1.3.6.1.4.1.52.1.2.2.1.3.1
This gives the number of Token Ring ports enabled on this device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

deviceTRPorts 1.3.6.1.4.1.52.1.2.2.1.3.2
This gives the total number of Token Ring ports on this device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

deviceTRRingPortsOn 1.3.6.1.4.1.52.1.2.2.1.3.3
This gives the number of Token Ring ring ports that are enabled.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

deviceTRRingPorts 1.3.6.1.4.1.52.1.2.2.1.3.4
This gives the total number of Token Ring ring ports on this device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

deviceTRLans 1.3.6.1.4.1.52.1.2.2.1.3.5
This gives the number of Token Rings formed on this device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

deviceTRBoards 1.3.6.1.4.1.52.1.2.2.1.3.6
This returns the number of Token Ring boards on the device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

deviceTRBoardMap 1.3.6.1.4.1.52.1.2.2.1.3.7
The slots that contain Token Ring MIM boards. This field is bit encoded (eg. if a bit is set then that board is present). For example, a value of 2 indicates that there is a Token Ring board in the first MIM slot.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

commonB 1.3.6.1.4.1.52.1.2.2.3.1
OBJECT IDENTIFIER    

ethernetB 1.3.6.1.4.1.52.1.2.2.3.2
OBJECT IDENTIFIER    

tokenRingB 1.3.6.1.4.1.52.1.2.2.3.3
OBJECT IDENTIFIER    

fDDIB 1.3.6.1.4.1.52.1.2.2.3.4
OBJECT IDENTIFIER    

boardIndex 1.3.6.1.4.1.52.1.2.2.3.1.1
The slot number of this board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

boardName 1.3.6.1.4.1.52.1.2.2.3.1.2
The name of the board. This field will only contain printable ASCII characters.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

boardType 1.3.6.1.4.1.52.1.2.2.3.1.3
The type of the MIM. (eg. FOT, TPT, etc). See appendix A for encoding.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

boardTotalPorts 1.3.6.1.4.1.52.1.2.2.3.1.4
Total number of ports supported on this board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

boardStatus 1.3.6.1.4.1.52.1.2.2.3.1.5
The administrative status of this MIM.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

boardPortsOn 1.3.6.1.4.1.52.1.2.2.3.1.6
The number of operating ports on the board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

boardOper 1.3.6.1.4.1.52.1.2.2.3.1.7
Returns a value indicating whether any of the enabled ports on the board are not operational, thereby placing the board in a non-operational state.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER operational(1), notOperational(2)  

boardActiveUsers 1.3.6.1.4.1.52.1.2.2.3.1.8
The number of active users seen on this board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

boardTotalPkts 1.3.6.1.4.1.52.1.2.2.3.2.1
The total number of packets this board has seen since the last reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

boardErrorPkts 1.3.6.1.4.1.52.1.2.2.3.2.2
The number of packets that have experienced an error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

boardTransColls 1.3.6.1.4.1.52.1.2.2.3.2.3
The number of transmit collisions this board has detected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

boardRecColls 1.3.6.1.4.1.52.1.2.2.3.2.4
The number of Receive mode collisions this board has detected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

boardAlignErrs 1.3.6.1.4.1.52.1.2.2.3.2.5
The number of misaligned frames this board has detected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

boardCRCErrs 1.3.6.1.4.1.52.1.2.2.3.2.6
The number of packets with bad CRC detected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

boardRunts 1.3.6.1.4.1.52.1.2.2.3.2.7
The number of runt frames detected by this board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

boardOOWColls 1.3.6.1.4.1.52.1.2.2.3.2.8
The number of out-of-window collisions detected by this board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

boardNoResources 1.3.6.1.4.1.52.1.2.2.3.2.9
The number of times the no resources condition was detected for this board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

boardRecBytes 1.3.6.1.4.1.52.1.2.2.3.2.10
The number of bytes detected on this board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

boardGiants 1.3.6.1.4.1.52.1.2.2.3.2.11
The number of packets longer than 1518 bytes detected on this board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

boardOSIFrames 1.3.6.1.4.1.52.1.2.2.3.2.12
The number of frames with OSI protocol seen by this board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

boardNovellFrames 1.3.6.1.4.1.52.1.2.2.3.2.13
The number of frames with NOVELL protocol seen by this board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

boardBanyanFrames 1.3.6.1.4.1.52.1.2.2.3.2.14
The number of frames with BANYAN protocol seen by this board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

boardDECNetFrames 1.3.6.1.4.1.52.1.2.2.3.2.15
The number of frames with DECNET protocol seen by this board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

boardXNSFrames 1.3.6.1.4.1.52.1.2.2.3.2.16
The number of frames with XNS protocol seen by this board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

boardIPFrames 1.3.6.1.4.1.52.1.2.2.3.2.17
The number of frames with TCPIP protocol seen by this board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

boardCtronFrames 1.3.6.1.4.1.52.1.2.2.3.2.18
The number of frames with Cabletron protocol seen by this board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

boardAppletalkFrames 1.3.6.1.4.1.52.1.2.2.3.2.19
The number of frames with Appletalk protocol seen by this board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

boardOtherFrames 1.3.6.1.4.1.52.1.2.2.3.2.20
The number of frames seen by this board, that do not fall into any of the previously listed protocol catagories.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

board64To127Frames 1.3.6.1.4.1.52.1.2.2.3.2.21
The number of frames seen by this board, with frame sizes between 64 and 127 bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

board128To255Frames 1.3.6.1.4.1.52.1.2.2.3.2.22
The number of frames seen by this board, with frame sizes between 128 and 255 bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

board256To511Frames 1.3.6.1.4.1.52.1.2.2.3.2.23
The number of frames seen by this board, with frame sizes between 256 and 511 bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

board512To1023Frames 1.3.6.1.4.1.52.1.2.2.3.2.24
The number of frames seen by this board, with frame sizes between 512 and 1023 bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

board1024To1518Frames 1.3.6.1.4.1.52.1.2.2.3.2.25
The number of frames seen by this board, with frame sizes between 1024 and 1518 bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

boardBroadPkts 1.3.6.1.4.1.52.1.2.2.3.2.26
The sum of broadcast packets detected on all ports of this board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

boardMultPkts 1.3.6.1.4.1.52.1.2.2.3.2.27
The sum of multicast packets detected on all ports of this board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

boardSrcAddrLocked 1.3.6.1.4.1.52.1.2.2.3.2.31
If this is set to 2, any source addresses that are detected on station port that are not in the table will cause the port to be turned off.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER lockOff(1), lockOn(2)  

boardTotalRingPorts 1.3.6.1.4.1.52.1.2.2.3.3.1
The total number of ring ports on this board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

boardTotalStationPorts 1.3.6.1.4.1.52.1.2.2.3.3.2
The total number of station ports on this board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

boardModeStatus 1.3.6.1.4.1.52.1.2.2.3.3.3
This describes the mode of this board. autoMode means the board is using the hardware defaults. mgmtMode means the board is using setting by the user.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER mgmtMode(1), autoMOde(2)  

boardTotalRingPortsOn 1.3.6.1.4.1.52.1.2.2.3.3.4
The number of enabled ring ports on this board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

boardTotalStationPortsOn 1.3.6.1.4.1.52.1.2.2.3.3.5
The number of enabled station ports on this board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

boardSpeed 1.3.6.1.4.1.52.1.2.2.3.3.6
The speed of the board. The board will expect to receive data at this speed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER fourMHz(4), sixteenMhz(16)  

ringSpeedFault 1.3.6.1.4.1.52.1.2.2.3.3.7
Data speed of station mismatches configuration speed of board. Board is automatically bypassed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER noFaultDetected(1), faultDetected(2)  

boardSpeedFaultPort 1.3.6.1.4.1.52.1.2.2.3.3.8
This object indicates which ring speed detect circuit(s) caused the fault, if there was one. The return code indicates the location on the board feeding the speed detect circuit(s). Ring in means the circuit on the back-up path between the ring out port and the ring in port. FNB means the circuit between the ring in port and the FNB. NotApplicable means that a ring Speed Fault has not occurred. Since more than one circuit can cause the fault, the return code is the sum of the following values: 1 - FNB 2 - RingIn 4 - RingOut 8 - NotApplicable
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

boardFirstRingPort 1.3.6.1.4.1.52.1.2.2.3.3.9
This object defines which port on the board is the first ring port. All ring port numbers will be consecutive. Using this in conjunction with BoardRingPorts, all ring port numbers can be determined.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

boardBypassRingPortState 1.3.6.1.4.1.52.1.2.2.3.3.10
This object sets and reports the state of the ring bypass relay on boards which contain a ring bypass relay. The ring bypass relay will separate only the ring ports from the FNB. The FNB only bypasses the station ports on these boards. The illegal value (3) will return an error status if set.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER off(1), on(2), illegal(3)  

commonP 1.3.6.1.4.1.52.1.2.2.4.1
OBJECT IDENTIFIER    

ethernetP 1.3.6.1.4.1.52.1.2.2.4.2
OBJECT IDENTIFIER    

tokenRingP 1.3.6.1.4.1.52.1.2.2.4.3
OBJECT IDENTIFIER    

fDDIP 1.3.6.1.4.1.52.1.2.2.4.4
OBJECT IDENTIFIER    

portIndex 1.3.6.1.4.1.52.1.2.2.4.1.1
The slot number of this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

portMediaType 1.3.6.1.4.1.52.1.2.2.4.1.2
The type of the port. (eg. FOT, TPT, etc).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER bnc(1), aui(2), tp(3), tenbt(4), fot(5), laser(6), stp(7), utp(8), fo(9), otherMedia(10)  

portAdminState 1.3.6.1.4.1.52.1.2.2.4.1.3
The administrative status of this port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER off(1), on(2)  

portSourceAddr 1.3.6.1.4.1.52.1.2.2.4.1.4
A source address that has been seen on this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

portOper 1.3.6.1.4.1.52.1.2.2.4.1.5
Returns a value indicating whether this port is in an operational state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notOperational(1), operational(2)  

portActiveUsers 1.3.6.1.4.1.52.1.2.2.4.1.6
The number of active users seen on this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

portName 1.3.6.1.4.1.52.1.2.2.4.1.7
The name of the port. this field will only contain printable ASCII characters.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

portTopologyType 1.3.6.1.4.1.52.1.2.2.4.2.1
The topological type of the port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER stations(1), trunk(2)  

portLinkStatus 1.3.6.1.4.1.52.1.2.2.4.2.2
The state of the link signal for this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER linkSignalInactive(1), linkSignalActive(2), linkSignalNotSupported(3)  

portStatus 1.3.6.1.4.1.52.1.2.2.4.2.3
The network state of this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER active(1), segmented(2)  

portTotalPkts 1.3.6.1.4.1.52.1.2.2.4.2.4
The total number of packets this port has seen since the last reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portErrorPkts 1.3.6.1.4.1.52.1.2.2.4.2.5
The number of packets that have experienced an error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portXmitColls 1.3.6.1.4.1.52.1.2.2.4.2.6
The number of Transmit mode collisions this port has detected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portRecColls 1.3.6.1.4.1.52.1.2.2.4.2.7
The number of Receive mode collisions this port has detected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portAlignErrs 1.3.6.1.4.1.52.1.2.2.4.2.8
The number of misaligned frames this port has detected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portCRCErrs 1.3.6.1.4.1.52.1.2.2.4.2.9
The number of packets with bad CRC detected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portRunts 1.3.6.1.4.1.52.1.2.2.4.2.10
The number of runt frames detected by this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portOOWColls 1.3.6.1.4.1.52.1.2.2.4.2.11
The number of out-of-window collisions detected by this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portNoResorces 1.3.6.1.4.1.52.1.2.2.4.2.12
The number of times the no resource condition is detected on this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portRecBytes 1.3.6.1.4.1.52.1.2.2.4.2.13
The number of bytes detected on the network.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portGiants 1.3.6.1.4.1.52.1.2.2.4.2.14
The number of frames longer than 1518 bytes detected on this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portRedundCrt 1.3.6.1.4.1.52.1.2.2.4.2.15
The redundant circuit with which this port is associated.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

portRedundType 1.3.6.1.4.1.52.1.2.2.4.2.16
The type of port this port is in the redundant circuit. The port must be associated with a redundant circuit first, using the object portRedundCrt.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER notUsed(1), primary(2), backup(3)  

portRedundStatus 1.3.6.1.4.1.52.1.2.2.4.2.17
The current state of this port is in the redundant circuit. The port must be associated with a redundant circuit first, using the object portRedundCrt.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER notUsed(1), active(2), inactive(3)  

portForceTrunkType 1.3.6.1.4.1.52.1.2.2.4.2.18
This variable forces a port to be a trunk port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER notForced(1), forced(2)  

portOSIFrames 1.3.6.1.4.1.52.1.2.2.4.2.19
The number of frames with OSI protocol seen by this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portNovellFrames 1.3.6.1.4.1.52.1.2.2.4.2.20
The number of frames with NOVELL protocol seen by this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portBanyanFrames 1.3.6.1.4.1.52.1.2.2.4.2.21
The number of frames with BANYAN protocol seen by this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portDECNetFrames 1.3.6.1.4.1.52.1.2.2.4.2.22
The number of frames with DECNET protocol seen by this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portXNSFrames 1.3.6.1.4.1.52.1.2.2.4.2.23
The number of frames with XNS protocol seen by this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portIPFrames 1.3.6.1.4.1.52.1.2.2.4.2.24
The number of frames with TCPIP protocol seen by this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portCtronFrames 1.3.6.1.4.1.52.1.2.2.4.2.25
The number of frames with Cabletron protocol seen by this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portAppletalkFrames 1.3.6.1.4.1.52.1.2.2.4.2.26
The number of frames with Appletalk protocol seen by this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portOtherFrames 1.3.6.1.4.1.52.1.2.2.4.2.27
The number of frames seen by this port, that do not fall into any of the previously listed protocol catagories.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

port64To127Frames 1.3.6.1.4.1.52.1.2.2.4.2.28
The number of frames seen by this port, with frame sizes between 64 and 127 bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

port128To255Frames 1.3.6.1.4.1.52.1.2.2.4.2.29
The number of frames seen by this port, with frame sizes between 128 and 255 bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

port256To511Frames 1.3.6.1.4.1.52.1.2.2.4.2.30
The number of frames seen by this port, with frame sizes between 256 and 511 bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

port512To1023Frames 1.3.6.1.4.1.52.1.2.2.4.2.31
The number of frames seen by this port, with frame sizes between 512 and 1023 bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

port1024To1518Frames 1.3.6.1.4.1.52.1.2.2.4.2.32
The number of frames seen by this port, with frame sizes between 1024 and 1518 bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portBroadPkts 1.3.6.1.4.1.52.1.2.2.4.2.33
The sum of broadcast packets detected on this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portMultPkts 1.3.6.1.4.1.52.1.2.2.4.2.34
The sum of multicast packets detected on this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portSrcAddrLocked 1.3.6.1.4.1.52.1.2.2.4.2.38
If this is set to 2, any source addresses that are detected on station ports that are not in the table will cause the port to be turned off.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER lockOff(1), lockOn(2)  

stationP 1.3.6.1.4.1.52.1.2.2.4.3.1
OBJECT IDENTIFIER    

ringP 1.3.6.1.4.1.52.1.2.2.4.3.2
OBJECT IDENTIFIER    

ringPort2 1.3.6.1.4.1.52.1.2.2.4.3.3
OBJECT IDENTIFIER    

commonRP 1.3.6.1.4.1.52.1.2.2.4.3.3.1
OBJECT IDENTIFIER    

autowrapRP 1.3.6.1.4.1.52.1.2.2.4.3.3.2
OBJECT IDENTIFIER    

stationPortLinkStatus 1.3.6.1.4.1.52.1.2.2.4.3.1.1
When station is supplying phantom current the Link Signal is active. When there is no phantom current the Link Signal is inactive.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER linkSignalInactive(1), linkSignalActive(2)  

stationPortLinkStateTime 1.3.6.1.4.1.52.1.2.2.4.3.1.2
The amount of in seconds which have elapsed since the station port last changed state. Note: setting this to zero will clear the time.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

ringPortLinkStatus 1.3.6.1.4.1.52.1.2.2.4.3.2.1
Reports the link state of a ring port.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER off(1), on(2)  

ringPortLinkStateTime 1.3.6.1.4.1.52.1.2.2.4.3.2.2
Reports the time (in seconds) since the ring port's link state changed.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER  

commonRPcapabilities 1.3.6.1.4.1.52.1.2.2.4.3.3.1.1
This object returns a code indicating that the queried ring port is nonautowrap, autowrap or selectable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER nonAutowrap(1), autowrap(2), selectable(3)  

autowrapRPFaultStatus 1.3.6.1.4.1.52.1.2.2.4.3.3.2.1
This object reports the wire fault of an autowrappable ring port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER faultUndetectable(1), noFaultDetected(2), faultDetected(3)  

autowrapRPFaultStateTime 1.3.6.1.4.1.52.1.2.2.4.3.3.2.2
This object reports the amount of time in time ticks since the ring port fault state last changed. Writing zero to this object resets the time. If a zero is read, it means either zero time ticks have passed or the ring port is nonautowrap.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

autowrapRPSelectedType 1.3.6.1.4.1.52.1.2.2.4.3.3.2.3
This object indicates the media type of the indicated ring port on some boards. Some boards provide both STP and fiber optic ring ports. The unselectable value will return an error if set. A set of STP or FO for a non-selectable ring port will not do anything, i.e. the status of normal is returned.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER unselectable(1), stp(2), fo(3)  

autowrapRPPhantomCurrent 1.3.6.1.4.1.52.1.2.2.4.3.3.2.4
This object tells the board to turn on phantom current for the ring port and look for wire faults. NoPhantomAvailable will return an error if set. A set of activatePhantom or deactivatePhantom for a non-autowrap ring port will not do anything, i.e. the status of normal is returned.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noPhantomAvailable(1), activatePhantom(2), deactivatePhantom(3)  

fNB 1.3.6.1.4.1.52.1.6.1.1
OBJECT IDENTIFIER    

connectedLeft 1.3.6.1.4.1.52.1.6.1.1.1
The Connected Left board (board n + 1) has the following states: Detached == 1 (Management (only management) detached, read/write). Attached == 2 (Management/AutoMode attached, read/write). Faulted == 3 (Management/AutoMode tried to attach but failed READ ONLY).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER detached(1), attached(2), faulted(3)  

connectedRight 1.3.6.1.4.1.52.1.6.1.1.2
The Connected Right board (board n - 1) has the following states: Detached == 1 (Management (only management) detached, read/write). Attached == 2 (Management/AutoMode attached, read/write ). Faulted == 3 (Management/AutoMode tried to attach but failed READ ONLY).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER detached(1), attached(2), faulted(3)  

boardBypassState 1.3.6.1.4.1.52.1.6.1.1.3
This object indicates that the board is in the bypassed state when it is ON. Bypassed means the board is NOT attached to the FNB.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER off(1), on(2)