IPOA-MIB
File:
IPOA-MIB.mib (56665 bytes)
Imported modules
Imported symbols
Defined Types
| IpoaEncapsType |
|
| The encapsulation type used on a VC. |
| TEXTUAL-CONVENTION |
|
|
|
| |
INTEGER |
llcSnap(1), vcMuxed(2), other(3) |
|
| IpoaAtmAddr |
|
| The ATM address used by the network entity.
The semantics are implied by the length.
The address types are:
- no address (0 octets)
- E.164 (8 octets)
- NSAP (20 octets)
In addition, when subaddresses are used IpoaAtmAddr
may represent the concatenation of address and
subaddress. The associated address types are:
- E.164, E.164 (16 octets)
- E.164, NSAP (28 octets)
- NSAP, NSAP (40 octets)
Address lengths other than defined in this definition
imply address types defined elsewhere.
Note: The E.164 address is encoded in BCD format. |
| TEXTUAL-CONVENTION |
|
|
|
| |
OCTET STRING |
Size(0..40) |
|
| IpoaAtmConnKind |
|
| The use of call control. The use is as follows:
pvc(1)
Virtual link of a PVC. Should not be
used in a PVC/SVC (i.e., SPVC)
crossconnect.
svcIncoming(2)
Virtual link established after a
received signaling request to setup
an SVC.
svcOutgoing(3)
Virtual link established after a
transmitted or forwarded signaling
request to setup an SVC.
spvcInitiator(4)
Virtual link at the PVC side of an
SVC/PVC crossconnect, where the
switch is the initiator of the SPVC
setup.
spvcTarget(5)
Virtual link at the PVC side of an
SVC/PVC crossconnect, where the
switch is the target of the SPVC
setup.
An spvcInitiator is always cross-connected to
an svcOutgoing, and an spvcTarget is always
cross-connected to an svcIncoming. |
| TEXTUAL-CONVENTION |
|
|
|
| |
INTEGER |
pvc(1), svcIncoming(2), svcOutgoing(3), spvcInitiator(4), spvcTarget(5) |
|
| IpoaLisEntry |
|
| SEQUENCE |
|
|
|
| |
ipoaLisSubnetAddr |
IpAddress |
|
| |
ipoaLisDefaultMtu |
Integer32 |
|
| |
ipoaLisDefaultEncapsType |
IpoaEncapsType |
|
| |
ipoaLisInactivityTimer |
Integer32 |
|
| |
ipoaLisMinHoldingTime |
Integer32 |
|
| |
ipoaLisQDepth |
Integer32 |
|
| |
ipoaLisMaxCalls |
Integer32 |
|
| |
ipoaLisCacheEntryAge |
Integer32 |
|
| |
ipoaLisRetries |
Integer32 |
|
| |
ipoaLisTimeout |
Integer32 |
|
| |
ipoaLisDefaultPeakCellRate |
Integer32 |
|
| |
ipoaLisActiveVcs |
Gauge32 |
|
| |
ipoaLisRowStatus |
RowStatus |
|
| IpoaLisIfMappingEntry |
|
| SEQUENCE |
|
|
|
| |
ipoaLisIfMappingIfIndex |
InterfaceIndex |
|
| |
ipoaLisIfMappingRowStatus |
RowStatus |
|
| IpoaArpClientEntry |
|
| SEQUENCE |
|
|
|
| |
ipoaArpClientAtmAddr |
IpoaAtmAddr |
|
| |
ipoaArpClientSrvrInUse |
IpoaAtmAddr |
|
| |
ipoaArpClientInArpInReqs |
Counter32 |
|
| |
ipoaArpClientInArpOutReqs |
Counter32 |
|
| |
ipoaArpClientInArpInReplies |
Counter32 |
|
| |
ipoaArpClientInArpOutReplies |
Counter32 |
|
| |
ipoaArpClientInArpInvalidInReqs |
Counter32 |
|
| |
ipoaArpClientInArpInvalidOutReqs |
Counter32 |
|
| |
ipoaArpClientArpInReqs |
Counter32 |
|
| |
ipoaArpClientArpOutReqs |
Counter32 |
|
| |
ipoaArpClientArpInReplies |
Counter32 |
|
| |
ipoaArpClientArpOutReplies |
Counter32 |
|
| |
ipoaArpClientArpInNaks |
Counter32 |
|
| |
ipoaArpClientArpOutNaks |
Counter32 |
|
| |
ipoaArpClientArpUnknownOps |
Counter32 |
|
| |
ipoaArpClientArpNoSrvrResps |
Counter32 |
|
| |
ipoaArpClientRowStatus |
RowStatus |
|
| IpoaArpSrvrEntry |
|
| SEQUENCE |
|
|
|
| |
ipoaArpSrvrAddr |
IpoaAtmAddr |
|
| |
ipoaArpSrvrLis |
IpAddress |
|
| |
ipoaArpSrvrInArpInReqs |
Counter32 |
|
| |
ipoaArpSrvrInArpOutReqs |
Counter32 |
|
| |
ipoaArpSrvrInArpInReplies |
Counter32 |
|
| |
ipoaArpSrvrInArpOutReplies |
Counter32 |
|
| |
ipoaArpSrvrInArpInvalidInReqs |
Counter32 |
|
| |
ipoaArpSrvrInArpInvalidOutReqs |
Counter32 |
|
| |
ipoaArpSrvrArpInReqs |
Counter32 |
|
| |
ipoaArpSrvrArpOutReplies |
Counter32 |
|
| |
ipoaArpSrvrArpOutNaks |
Counter32 |
|
| |
ipoaArpSrvrArpDupIpAddrs |
Counter32 |
|
| |
ipoaArpSrvrArpUnknownOps |
Counter32 |
|
| |
ipoaArpSrvrRowStatus |
RowStatus |
|
| IpoaArpRemoteSrvrEntry |
|
| SEQUENCE |
|
|
|
| |
ipoaArpRemoteSrvrAtmAddr |
IpoaAtmAddr |
|
| |
ipoaArpRemoteSrvrRowStatus |
RowStatus |
|
| |
ipoaArpRemoteSrvrIfIndex |
InterfaceIndexOrZero |
|
| |
ipoaArpRemoteSrvrIpAddr |
IpAddress |
|
| |
ipoaArpRemoteSrvrAdminStatus |
INTEGER |
|
| |
ipoaArpRemoteSrvrOperStatus |
INTEGER |
|
| IpoaVcEntry |
|
| SEQUENCE |
|
|
|
| |
ipoaVcVpi |
IpoaVpiInteger |
|
| |
ipoaVcVci |
IpoaVciInteger |
|
| |
ipoaVcType |
IpoaAtmConnKind |
|
| |
ipoaVcNegotiatedEncapsType |
IpoaEncapsType |
|
| |
ipoaVcNegotiatedMtu |
Integer32 |
|
| IpoaConfigPvcEntry |
|
| SEQUENCE |
|
|
|
| |
ipoaConfigPvcIfIndex |
InterfaceIndex |
|
| |
ipoaConfigPvcVpi |
IpoaVpiInteger |
|
| |
ipoaConfigPvcVci |
IpoaVciInteger |
|
| |
ipoaConfigPvcDefaultMtu |
Integer32 |
|
| |
ipoaConfigPvcRowStatus |
RowStatus |
|
Defined Values
| ipoaMIB |
1.3.6.1.2.1.10.46 |
| This module defines a portion of the management
information base (MIB) for managing Classical IP and
ARP over ATM entities. |
| MODULE-IDENTITY |
|
|
|
| ipoaLisTrapEnable |
1.3.6.1.2.1.10.46.1.1 |
| Indicates whether ipoaLisCreate and ipoaLisDelete
traps should be generated by this system.
By default, this object should have the value
enabled(1) for systems where ATMARP Servers are
present and disabled(2) on systems where only
clients reside. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| ipoaLisTable |
1.3.6.1.2.1.10.46.1.2 |
| There is one entry in this table for every Logical IP
Subnet (LIS) of which this system is a member.
The bulk of the objects in an ipoaLisEntry exists
to control ATMARP for a particular LIS. In a PVC only
environment it is implementation dependent as to
whether this table should be supported. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
IpoaLisEntry |
|
| ipoaLisEntry |
1.3.6.1.2.1.10.46.1.2.1 |
| Information about a single LIS of which this system
is a member.
Membership in a LIS is independent of the actual ATM
interfaces being used. The ipoaLisTable defines
all LISs that a system is a member of. The ipAddrTable
and the ipoaClientTable provides the mapping from local
IP address to ATM interface. The ipoaLisIfMappingTable
provides the mappings between Logical IP Subnets and
interfaces.
The ipoaLisTable is indexed by ipoaLisSubnetAddr (IP
subnet address). An entry in the ipoaLisTable should
exist for each ipAddrEntry that is associated with an
ATM related interface used for Classical IP and ARP
over ATM traffic.
Its ipAdEntAddr and ipAdEntNetMask when ANDed together
should equal the ipoaLisSubnetAddr of the corresponding
ipoaLisEntry. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
IpoaLisEntry |
|
|
| ipoaLisSubnetAddr |
1.3.6.1.2.1.10.46.1.2.1.1 |
| The IP subnet address associated with this LIS. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
IpAddress |
|
|
| ipoaLisDefaultMtu |
1.3.6.1.2.1.10.46.1.2.1.2 |
| The default MTU used within this LIS. Note that the
actual MTU used for a VC between two members of the
LIS may be negotiated during connection setup and may
be different than this value. The ipoaVcNegotiatedMtu
object indicates the actual MTU in use for a
particular VC. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..65535 |
|
| ipoaLisDefaultEncapsType |
1.3.6.1.2.1.10.46.1.2.1.3 |
| The default encapsulation to use on VCs created for
this LIS. Note that the actual encapsulation type may
be negotiated during connection setup and may be
different than this value. The
ipoaVcNegotiatedEncapsType object indicates the actual
encapsulation in use for a particular VC. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
IpoaEncapsType |
|
|
| ipoaLisInactivityTimer |
1.3.6.1.2.1.10.46.1.2.1.4 |
| The time, in seconds, before a call established for an
ipNetToMediaEntry on a client will timeout due to no
traffic being passed on the VC. A value of 0 implies
no time out. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| ipoaLisMinHoldingTime |
1.3.6.1.2.1.10.46.1.2.1.5 |
| The minimum amount of time, in seconds, that a call
will remain open. If 0 then ipoaInactivityTimer will
completely determine when a call is terminated. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..65535 |
|
| ipoaLisQDepth |
1.3.6.1.2.1.10.46.1.2.1.6 |
| The maximum number of outstanding requests that are
allowed while waiting for ATMARP replies and
InATMARP replies for this LIS. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
1..65535 |
|
| ipoaLisMaxCalls |
1.3.6.1.2.1.10.46.1.2.1.7 |
| The maximum number of SVCs that can be established
simultaneously for this LIS. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
1..65535 |
|
| ipoaLisCacheEntryAge |
1.3.6.1.2.1.10.46.1.2.1.8 |
| The time, in seconds, before an ipNetToMediaEntry will
age out of the table. Note that the default value will
be different for a client and a server. An ATMARP
Server should use a default of 1200 and a client should
use 900. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
60..1200 |
|
| ipoaLisRetries |
1.3.6.1.2.1.10.46.1.2.1.9 |
| The number of times the ATMARP request will be retried
when no response is received in the timeout interval
indicated by ipoaLisTimeout. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..10 |
|
| ipoaLisTimeout |
1.3.6.1.2.1.10.46.1.2.1.10 |
| The time to wait, in seconds, before retransmission
of an ARP request. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
1..60 |
|
| ipoaLisDefaultPeakCellRate |
1.3.6.1.2.1.10.46.1.2.1.11 |
| This object is the signalling parameter that
should be used when setting up all best effort
VCCs (Virtual Channel Connections).
This parameter applies to the forward and
backward direction on a per best effort VCC basis.
A value of zero implies that no configured default
exists and that local policy should be used to
determine the actual default to used during
call setup. ATM Signaling Support for IP over ATM
(RFC 1755) recommends 1/10th of the ATM interface's
speed. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| ipoaLisActiveVcs |
1.3.6.1.2.1.10.46.1.2.1.12 |
| Number of active SVCs for this LIS. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
|
|
| ipoaLisRowStatus |
1.3.6.1.2.1.10.46.1.2.1.13 |
| This object allows entries to be created and deleted
in the ipoaLisTable.
When the ipoaLisRowStatus deleted (by setting this
object to destroy(6)), this has the side-effect of
removing all entries from the ipNetToMediaTable that
are associated with this LIS (in other words, it
flushes the entity's ATMARP cache). It also removes
the ipoaVcTable entries that were associated with those
ipNetToMediaTable entries. Destroying the row also
removes the corresponding entries in the
ipoaArpSrvrTable, ipoaArpClientTable,
ipoaLisIfMappingTable, and ipoaArpRemoteSrvrTable.
Entries in both the ipNetToMediaTable and the
ipoaVcTable that are associated with a
ipoaConfigPvcEntry are not affected by changes to
ipoaLisRowStatus. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
RowStatus |
|
|
| ipoaLisIfMappingTable |
1.3.6.1.2.1.10.46.1.3 |
| There is one entry in this table for every combination
of ipoaLisEntry and IP over ATM interface. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
IpoaLisIfMappingEntry |
|
| ipoaLisIfMappingEntry |
1.3.6.1.2.1.10.46.1.3.1 |
| Defines an entry in the ipoaLisIfMappingTable. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
IpoaLisIfMappingEntry |
|
|
| ipoaLisIfMappingIfIndex |
1.3.6.1.2.1.10.46.1.3.1.1 |
| The ipAdEntIfIndex object from an ipAddrEntry
is used as an index to this table when its
ipAdEntAddr is in the subnet implied by
ipoaLisSubnetAddr. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
InterfaceIndex |
|
|
| ipoaLisIfMappingRowStatus |
1.3.6.1.2.1.10.46.1.3.1.2 |
| This object allows entries to be created and deleted
in the ipoaLisIfMappingTable. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
RowStatus |
|
|
| ipoaArpClientEntry |
1.3.6.1.2.1.10.46.1.4.1 |
| Information about a single ATMARP Client. Clients
can be started and stopped by adding and removing
entries from this table. An entry in the
ipoaArpClientTable has a corresponding entry in the
ipAddrTable. Both are indexed by ipAdEntAddr.
The ifIndex and subnet mask of a client entry are the
ipAddrEntry's ipAdEntIfIndex and ipAdEntNetMask,
respectively.
Note that adding and removing entries from this table
may have the same effect on the corresponding
ipAddrTable entry. Row creation of an entry in this
table requires that either the corresponding ipAddrTable
entry exists or that ipAdEntIfIndex and ipAdEntNetMask
be specified in the creation of an ipoaArpClientEntry
at a minimum in order to create the corresponding
ipAddrEntry. Specification of ipAdEntBcastAddr and
ipAdEntReasmMaxSize to complete an ipAddrEntry is
implementation dependent.
Whether a corresponding ipAddrEntry is deleted during
the deletion of an ipoaArpClientEntry is considered
implementation dependent. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
IpoaArpClientEntry |
|
|
| ipoaArpClientSrvrInUse |
1.3.6.1.2.1.10.46.1.4.1.2 |
| The ATM address of the ATMARP Server,
ipoaArpRemoteSrvrAtmAddr, in use by this client. A
zero length octet string implies that communication
with a Remote ATMARP Server is not in effect. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
IpoaAtmAddr |
|
|
| ipoaArpClientArpInReqs |
1.3.6.1.2.1.10.46.1.4.1.9 |
| Total number of ATMARP requests received by this
client. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| ipoaArpClientArpInNaks |
1.3.6.1.2.1.10.46.1.4.1.13 |
| Total number of negative ATMARP replies
received by this client. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| ipoaArpClientArpOutNaks |
1.3.6.1.2.1.10.46.1.4.1.14 |
| Total number of negative ATMARP replies sent by
this client.
Classic IP and ARP over ATM does not require an
ATMARP client to transmit an ATMARP_NAK upon
receipt of an ATMARP request from another ATMARP
client. However, implementation experience has
shown that this error condition is somewhat easy
to create inadvertently by configuring one ATMARP
client with an ipoaArpRemoteSrvrTable entry
containing an ipoaArpRemoteSrvrAtmAddr value which
is the ATM address of another ATMARP client-only
system.
If an ATMARP client supports the transmission of
ATMARP_NAKs, then it should increment
ipoaArpClientArpOutNaks each time it transmits
an ATMARP_NAK. Otherwise, support of this
object is considered optional. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| ipoaArpClientArpUnknownOps |
1.3.6.1.2.1.10.46.1.4.1.15 |
| The number of times that this client received
an ATMARP message with an operation code for which
it is not coded to support. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| ipoaArpClientArpNoSrvrResps |
1.3.6.1.2.1.10.46.1.4.1.16 |
| The number of times this client failed to receive
a response from a ATMARP Server within the
ipoaLisTimeout value for ipoaLisRetries times.
This may imply that the client will re-elect a
new primary ATMARP Server for this LIS from the
ipoaArpRemoteSrvrTable. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| ipoaArpClientRowStatus |
1.3.6.1.2.1.10.46.1.4.1.17 |
| This object allows entries to be created and
deleted from the ipoaArpClientTable. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
RowStatus |
|
|
| ipoaArpSrvrTable |
1.3.6.1.2.1.10.46.1.5 |
| The ATMARP Servers running on this system. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
IpoaArpSrvrEntry |
|
| ipoaArpSrvrEntry |
1.3.6.1.2.1.10.46.1.5.1 |
| Information about an ATMARP Server within a LIS. An
entry in this table has two indexes: first ipAdEntAddr,
which is the IP address that this system uses as a
member of the LIS, and then ipoaArpSrvrAddr, which is
the ATM address of the ATMARP Server.
Entries may be created by a management application
using the ipoaArpSrvrRowStatus object. Entries in this
table may also be created by the system and not by a
management application, for example via ILMI.
Entries in this table may be deleted by setting the
ipoaArpSrvrRowStatus object to 'destroy(6)'. This
includes entries that were added by the system and not
by a management application. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
IpoaArpSrvrEntry |
|
|
| ipoaArpSrvrAddr |
1.3.6.1.2.1.10.46.1.5.1.1 |
| The ATM address of the ATMARP Server. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
IpoaAtmAddr |
|
|
| ipoaArpSrvrLis |
1.3.6.1.2.1.10.46.1.5.1.2 |
| The subnet address that identifies the LIS with
which this server is associated. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
IpAddress |
|
|
| ipoaArpSrvrInArpInReqs |
1.3.6.1.2.1.10.46.1.5.1.3 |
| The number of InATMARP requests received by this
ATMARP Server. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| ipoaArpSrvrInArpOutReqs |
1.3.6.1.2.1.10.46.1.5.1.4 |
| The number of InATMARP requests sent by this ATMARP
Server. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| ipoaArpSrvrInArpInReplies |
1.3.6.1.2.1.10.46.1.5.1.5 |
| The number of InATMARP replies received by this
ATMARP Server. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| ipoaArpSrvrArpInReqs |
1.3.6.1.2.1.10.46.1.5.1.9 |
| Total number of ATMARP requests received by this
ATMARP Server. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| ipoaArpSrvrArpOutReplies |
1.3.6.1.2.1.10.46.1.5.1.10 |
| Total number of ATMARP replies sent by this ATMARP
Server. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| ipoaArpSrvrArpOutNaks |
1.3.6.1.2.1.10.46.1.5.1.11 |
| Total number of negative ATMARP replies sent by this
ATMARP Server. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| ipoaArpSrvrArpDupIpAddrs |
1.3.6.1.2.1.10.46.1.5.1.12 |
| The number of times that a duplicate IP address was
detected by this ATMARP Server. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| ipoaArpSrvrArpUnknownOps |
1.3.6.1.2.1.10.46.1.5.1.13 |
| The number of times that this ATMARP Server received
an ATMARP message with an operation code for which it
is not coded to support. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| ipoaArpSrvrRowStatus |
1.3.6.1.2.1.10.46.1.5.1.14 |
| This object allows entries to be created and deleted
from the ipoaArpSrvrTable. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
RowStatus |
|
|
| ipoaArpRemoteSrvrTable |
1.3.6.1.2.1.10.46.1.6 |
| A table of non-local ATMARP Servers associated with a
LIS. An entry in this table has three indexes: first
the ipoaLisSubnetAddr of the LIS for which the
corresponding ATMARP Server provides ATMARP services,
then the ipoaArpRemoteSrvrAtmAddr, which is the ATM
address of the remote ATMARP Server, and finally the
ifIndex of the interface on which the VC to the ATMARP
Remote Server will be opened. An ifIndex value of 0
should be used when a single VC is to be shared for
ATMARP purposes by multiple interfaces. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
IpoaArpRemoteSrvrEntry |
|
| ipoaArpRemoteSrvrEntry |
1.3.6.1.2.1.10.46.1.6.1 |
| Information about one non-local ATMARP Server. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
IpoaArpRemoteSrvrEntry |
|
|
| ipoaArpRemoteSrvrRowStatus |
1.3.6.1.2.1.10.46.1.6.1.2 |
| This object allows entries to be created and deleted
from the ipoaArpRemoteSrvrTable.
Deleting an ipoaArpRemoteSrvrEntry (by setting this
object to destroy(6)) may affect ipoaArpClientTable
entries. The object ipoaArpClientSrvrInUse in an
ipoaArpClientSrvrEntry may contain the ATM address
of an ATMARP Remote Server whose entry in the
ipoaArpRemoteSrvrTable is being removed. In this
case, any corresponding ipoaArpClientSrvrInUse
objects should be at a minimum invalidated by
setting their values to that of a zero length
OCTET STRING.
The value of ipoaArpRemoteSrvrOperStatus should be
consistent with that of ipoaArpRemoteSrvrRowStatus.
For example, successfully setting the value of
this object to notInService(2) after its being in
the up(1) state should result in
ipoaArpRemoteSrvrOperStatus being set to down(2)
if currently up(1). |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
RowStatus |
|
|
| ipoaArpRemoteSrvrIpAddr |
1.3.6.1.2.1.10.46.1.6.1.4 |
| The IP Address of the Remote ATMARP Server. A
value of 0.0.0.0 implies that this address isn't
known. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
IpAddress |
|
|
| ipoaArpRemoteSrvrAdminStatus |
1.3.6.1.2.1.10.46.1.6.1.5 |
| The desired state for use of the ATMARP Server
represented by an entry in this table.
ipoaArpRemoteSrvrAdminStatus values:
up(1) - Attempt to activate use of the
ATMARP Server represented by this
entry in the ipoaArpRemoteSrvrTable.
down(2) - Deactivate use of this ATMARP
Server.
When a managed system creates an entry in this
table ipoaArpRemoteSrvrAdminStatus and
ipoaArpRemoteSrvrOperStatus are initialized as
down(2) by default. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
up(1), down(2) |
|
| ipoaArpRemoteSrvrOperStatus |
1.3.6.1.2.1.10.46.1.6.1.6 |
| The current operational state for use of a Remote
ATMARP Server. An up(1) entry has a VC
established to the respective Remote ATMARP
Server:
up(1) - A VC exists to Remote ATMARP Server
whose IP Address is stored in
ipoaArpRemoteSrvrIpAddr. This VC can
be determined by searching the
ipoaVcTable using
ipoaArpRemoteSrvrIfIndex (if not 0,
otherwise ignore ipNetToMediaIfIndex
index) and ipoaArpRemoteSrvrIpAddr.
An ipoaArpClientEntry should exist
with its ipoaArpClientSrvrInUse
object having the same value as
ipoaArpRemoteSrvrAtmAddr.
down(2) - Entry exists without an active VC to
the Remote ATMARP Server.
Transition from up(1) to down(2)
status may affect ipoaArpClientTable entries.
The object ipoaArpClientSrvrInUse in an
ipoaArpClientSrvrEntry may contain the ATM address
of an ATMARP Remote Server whose entry in the
ipoaArpRemoteSrvrTable is being deactivated. In
this case, any corresponding ipoaArpClientSrvrInUse
objects should be at a minimum invalidated by
setting their values to that of a zero length
OCTET STRING.
If ipoaArpRemoteSrvrAdminStatus is down(2) then
ipoaArpRemoteSrvrOperStatus should be down(2).
If ipoaArpRemoteSrvrAdminStatus is changed to
up(1) then ipoaArpRemoteSrvrOperStatus should
change to up(1) if the Remote ATMARP Server
entry can be activated. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
up(1), down(2) |
|
| ipoaVcTable |
1.3.6.1.2.1.10.46.1.7 |
| A system that supports IP over ATM is an IP system and
therefore MUST support all of the appropriate tables in
the SNMPv2-MIB (RFC 1907), the IF-MIB (RFC 2233),
the IP-MIB (RFC 2011), the TCP-MIB (RFC 2012), and
the UDP-MIB (RFC 2013). This includes the
ipNetToMediaTable (the ARP cache) that is defined
within the IP-MIB (RFC 2011). The ipoaVcTable
keeps a set of VCs for each entry in the ARP cache
that was put there by an IP over ATM system acting
as either a host or server. The ipoaVcTable doesn't
augment the ipNetToMediaTable (ARP Cache) since the
the correspondence between tables is not necessarily
one-to-one.
An ipNetToMediaPhysAddress object should contain the
content as defined by the IpoaAtmAddr textual
convention when used to hold an IPOA-MIB ATM Address. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
IpoaVcEntry |
|
| ipoaVcEntry |
1.3.6.1.2.1.10.46.1.7.1 |
| A VC (permanent or switched) that this host or server
has opened with another member of a LIS. Additional
information can be determined about the VC from the
ATM-MIB.
Entries in this table cannot be created by management
applications.
In an SVC environment, an entry is automatically added
by the system as the result of ATMARP processing.
In a PVC environment, an entry is automatically added
to this table when an entry is created in the
ipoaConfigPvcTable and the IP Address at the remote
end of the PVC is discovered using InATMARP. An
entry also is added to the ipNetToMediaTable. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
IpoaVcEntry |
|
|
| ipoaVcVpi |
1.3.6.1.2.1.10.46.1.7.1.1 |
| The VPI value for the Virtual Circuit. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
IpoaVpiInteger |
|
|
| ipoaVcVci |
1.3.6.1.2.1.10.46.1.7.1.2 |
| The VCI value for the Virtual Circuit. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
IpoaVciInteger |
|
|
| ipoaVcType |
1.3.6.1.2.1.10.46.1.7.1.3 |
| The type of the Virtual Circuit. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
IpoaAtmConnKind |
|
|
| ipoaVcNegotiatedMtu |
1.3.6.1.2.1.10.46.1.7.1.5 |
| The MTU used when communicating over this circuit. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..65535 |
|
| ipoaConfigPvcTable |
1.3.6.1.2.1.10.46.1.8 |
| This table MUST be supported when PVCs are intended to
be supported in order to enable the setup of PVCs for
use by IP. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
IpoaConfigPvcEntry |
|
| ipoaConfigPvcEntry |
1.3.6.1.2.1.10.46.1.8.1 |
| Defines a single PVC that exists at this host for
use by IP. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
IpoaConfigPvcEntry |
|
|
| ipoaConfigPvcIfIndex |
1.3.6.1.2.1.10.46.1.8.1.1 |
| The ifIndex of the ATM Interface that this PVC
is associated with. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
InterfaceIndex |
|
|
| ipoaConfigPvcDefaultMtu |
1.3.6.1.2.1.10.46.1.8.1.4 |
| Classical IP and ARP over ATM allows use of
other MTU values for PVCs but considers how a
value other than 9180 could be selected to be out
of scope. ipoaConfigPvcDefaultMtu can be used to
configure the MTU to be used for the PVC.
Both ends MUST have the same value configured. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..65535 |
|
| ipoaConfigPvcRowStatus |
1.3.6.1.2.1.10.46.1.8.1.5 |
| This object allows rows to be created and deleted in
the ipoaConfigPvcTable. Creation of an entry in this
table should eventually result in the creation of an
ipNetToMediaEntry and a corresponding ipoaVcEntry
after InATMARP has determined the destination address
of the remote system that the PVC is connected to.
Setting this object to destroy(6) should remove the
corresponding ipNetToMediaTable and ipoaVcTable
entries. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
RowStatus |
|
|
| ipoaMtuExceeded |
1.3.6.1.2.1.10.46.2.0.1 |
| A frame was received that exceeds the negotiated
MTU size. The VPI and VCI of the VC for which this
condition was detected can be determined from the
index values for ipoaVcNegotiatedMtu. In addition,
the ifIndex and IP Address can be determined as
well (refer to the ipoaVcTable). |
| Status: current |
Access: read-create |
| NOTIFICATION-TYPE |
|
|
|
| ipoaDuplicateIpAddress |
1.3.6.1.2.1.10.46.2.0.2 |
| The ATMARP Server has detected more than one ATM end
point attempting to associate the same IP address with
different ATM addresses. |
| Status: current |
Access: read-create |
| NOTIFICATION-TYPE |
|
|
|
| ipoaLisCreate |
1.3.6.1.2.1.10.46.2.0.3 |
| Generation of this trap occurs when an ipoaLisEntry is
created while the ipoaLisTrapEnable.0 object has the
value enabled(1). |
| Status: current |
Access: read-create |
| NOTIFICATION-TYPE |
|
|
|
| ipoaLisDelete |
1.3.6.1.2.1.10.46.2.0.4 |
| Generation of this trap occurs when an ipoaLisEntry is
deleted while the ipoaLisTrapEnable.0 object has the
value enabled(1). |
| Status: current |
Access: read-create |
| NOTIFICATION-TYPE |
|
|
|
| ipoaGroups |
1.3.6.1.2.1.10.46.3.1 |
| OBJECT IDENTIFIER |
|
|
|
| ipoaCompliance |
1.3.6.1.2.1.10.46.3.2.1 |
| The compliance statement for agents that support the
IPOA-MIB. |
| Status: current |
Access: not-accessible |
| MODULE-COMPLIANCE |
|
|
|
| ipoaGeneralGroup |
1.3.6.1.2.1.10.46.3.1.1 |
| This group is mandatory for all IP over ATM entities. |
| Status: current |
Access: not-accessible |
| OBJECT-GROUP |
|
|
|
| ipoaClientGroup |
1.3.6.1.2.1.10.46.3.1.2 |
| This group is mandatory for all hosts where an IP
over ATM client is present. |
| Status: current |
Access: not-accessible |
| OBJECT-GROUP |
|
|
|
| ipoaSrvrGroup |
1.3.6.1.2.1.10.46.3.1.3 |
| This group is mandatory for all hosts where ATMARP
Servers are present. |
| Status: current |
Access: not-accessible |
| OBJECT-GROUP |
|
|
|
| ipoaBasicNotificationsGroup |
1.3.6.1.2.1.10.46.3.1.4 |
| The notification which an IP over ATM entity
is required to implement. |
| Status: current |
Access: not-accessible |
| NOTIFICATION-GROUP |
|
|
|
| ipoaSrvrNotificationsGroup |
1.3.6.1.2.1.10.46.3.1.5 |
| The notification which an IP over ATM ATMARP
Server is required to implement. |
| Status: current |
Access: not-accessible |
| NOTIFICATION-GROUP |
|
|
|
| ipoaLisNotificationsGroup |
1.3.6.1.2.1.10.46.3.1.6 |
| The LIS-related notifications which are required
to be implemented by an IP over ATM ATMARP server,
as well as by any IP over ATM client which allows
ipoaLisTrapEnable to be set to enabled(1). |
| Status: current |
Access: not-accessible |
| NOTIFICATION-GROUP |
|
|
|
| ipoaLisTableGroup |
1.3.6.1.2.1.10.46.3.1.7 |
| This group is mandatory for all entities which
support IP over ATM SVCs. Support of objects in
this group by IP over ATM clients which only
support IP over ATM PVCs is optional. |
| Status: current |
Access: not-accessible |
| OBJECT-GROUP |
|
|
|