INTERFACES-MIB

Imported modules

Imported symbols

enterprises	TimeTicks	OBJECT-TYPE
DisplayString

Defined Types

MgmtPortsTableEntry
SEQUENCE
	mgmtPortsTableIndex	INTEGER
	mgmtPortsDescription	DisplayString
	mgmtPortsElementID	DisplayString
	mgmtPortsMode	INTEGER
	mgmtPortsDialPrefix	DisplayString
	mgmtPortsPrimaryDialString	DisplayString
	mgmtPortsSecondaryDialString	DisplayString
	mgmtPortsExtInitString	DisplayString
	mgmtPortsCompressedSlip	INTEGER
	mgmtPortsInternalModem	INTEGER

DbuConfigTableEntry
SEQUENCE
	dbuNearIndex	INTEGER
	dbuFarIndex	INTEGER
	dbuConfigTableIndex	INTEGER
	dbuDescription	DisplayString
	dbuRate	INTEGER
	dbuMode	INTEGER
	dbuFormat	INTEGER
	dbuNumber	DisplayString
	dbuStatus	INTEGER
	dbuCommand	INTEGER
	dbuActivator1	INTEGER
	dbuActivator2	INTEGER
	dbuDialStr	DisplayString
	dbuInitStr	DisplayString
	dbuHangupStr	DisplayString
	dbuPasswordStr	DisplayString
	dbuSecurity	INTEGER
	dbuDtrDial	INTEGER
	dbuISDNSwitchType	INTEGER
	dbuISDNSwitchVersion	INTEGER
	dbuISDNTEI	INTEGER
	dbuISDNSPID	DisplayString
	dbuISDNDDNUM	DisplayString

DbuResetStringsEntry
SEQUENCE
	dbuResetNearIndex	INTEGER
	dbuResetFarIndex	INTEGER
	dbuResetConfigEntryIndex	INTEGER
	dbuResetStringsIndex	INTEGER
	dbuResetString	DisplayString

DbuStartStopTableEntry
SEQUENCE
	dbuStartStopNearIndex	INTEGER
	dbuStartStopFarIndex	INTEGER
	dbuStartStopConfigEntryIndex	INTEGER
	dbuStartStopDayOfWeek	INTEGER
	dbuStart	INTEGER
	dbuStop	INTEGER

T1e1ConfigTableEntry
SEQUENCE
	t1e1ConfigNearIndex	INTEGER
	t1e1ConfigFarIndex	INTEGER
	t1e1ConfigIndex	INTEGER
	t1e1Description	DisplayString
	t1e1Mode	INTEGER
	t1e1FrameType	INTEGER
	t1e1LineCode	INTEGER
	t1e1LineBuildOut	INTEGER
	t1e1Timing	INTEGER
	t1e1StationInTiming	INTEGER
	t1e1StationTiming	INTEGER
	t1e1PRM	INTEGER
	t1e1ZeroSuppress	INTEGER
	t1e1NationalBit	INTEGER
	t1e1KeepAlive	INTEGER
	t1e1CRC4Mode	INTEGER
	t1e1DSXLevel	INTEGER
	t1e1CRC	INTEGER
	t1e1FDLPassThrough	INTEGER
	t1e1AudibleAlarm	INTEGER

T1e1AlarmTableEntry
SEQUENCE
	t1e1AlarmNearIndex	INTEGER
	t1e1AlarmFarIndex	INTEGER
	t1e1AlarmIndex	INTEGER
	t1e1StatusSummary	DisplayString
	t1e1AlarmSummary	DisplayString
	t1e1ESStatus	INTEGER
	t1e1ESCount	INTEGER
	t1e1ESThreshold	INTEGER
	t1e1ESAlarm	INTEGER
	t1e1SESStatus	INTEGER
	t1e1SESCount	INTEGER
	t1e1SESThreshold	INTEGER
	t1e1SESAlarm	INTEGER
	t1e1LOSSStatus	INTEGER
	t1e1LOSSCount	INTEGER
	t1e1LOSSThreshold	INTEGER
	t1e1LOSSAlarm	INTEGER
	t1e1UASStatus	INTEGER
	t1e1UASCount	INTEGER
	t1e1UASThreshold	INTEGER
	t1e1UASAlarm	INTEGER
	t1e1CSSStatus	INTEGER
	t1e1CSSCount	INTEGER
	t1e1CSSThreshold	INTEGER
	t1e1CSSAlarm	INTEGER
	t1e1BPVSStatus	INTEGER
	t1e1BPVSCount	INTEGER
	t1e1BPVSThreshold	INTEGER
	t1e1BPVSAlarm	INTEGER
	t1e1OOFSStatus	INTEGER
	t1e1OOFSCount	INTEGER
	t1e1OOFSThreshold	INTEGER
	t1e1OOFSAlarm	INTEGER
	t1e1AISStatus	INTEGER
	t1e1AISCount	INTEGER
	t1e1AISThreshold	INTEGER
	t1e1AISAlarm	INTEGER
	t1e1RASStatus	INTEGER
	t1e1RASCount	INTEGER
	t1e1RASThreshold	INTEGER
	t1e1RASAlarm	INTEGER
	t1e1AlarmResetTimer	INTEGER
	t1e1AlarmReset	INTEGER

DdsNetConfigTableEntry
SEQUENCE
	ddsNetConfigNearIndex	INTEGER
	ddsNetConfigFarIndex	INTEGER
	ddsNetConfigIndex	INTEGER
	ddsNetDescription	DisplayString
	ddsNetRate	INTEGER
	ddsNetMode	INTEGER
	ddsNetTimingSource	INTEGER
	ddsNetRemComm	INTEGER
	ddsNetCircuitAssur	INTEGER
	ddsNetAntiStrTimer	INTEGER

DdsNetAlarmTableEntry
SEQUENCE
	ddsNetAlarmNearIndex	INTEGER
	ddsNetAlarmFarIndex	INTEGER
	ddsNetAlarmIndex	INTEGER
	ddsNetStatusSummary	DisplayString
	ddsNetAlarmSummary	DisplayString
	ddsNetLOSStatus	INTEGER
	ddsNetLOSCount	INTEGER
	ddsNetLOSThreshold	INTEGER
	ddsNetLOSAlarm	INTEGER
	ddsNetOOFStatus	INTEGER
	ddsNetOOFCount	INTEGER
	ddsNetOOFThreshold	INTEGER
	ddsNetOOFAlarm	INTEGER
	ddsNetOOSStatus	INTEGER
	ddsNetOOSCount	INTEGER
	ddsNetOOSThreshold	INTEGER
	ddsNetOOSAlarm	INTEGER
	ddsNetFDLStatus	INTEGER
	ddsNetFDLCount	INTEGER
	ddsNetFDLThreshold	INTEGER
	ddsNetFDLAlarm	INTEGER
	ddsNetAlarmResetTimer	INTEGER
	ddsNetAlarmReset	INTEGER

SerialDteConfigTableEntry
SEQUENCE
	serialDteConfigNearIndex	INTEGER
	serialDteConfigFarIndex	INTEGER
	serialDteConfigIndex	INTEGER
	serialDteDescription	DisplayString
	serialDteType	INTEGER
	serialDteRate	INTEGER
	serialDteInvertData	INTEGER
	serialDteFormat	INTEGER
	serialDteParity	INTEGER
	serialDteStopBit	INTEGER
	serialDteMode	INTEGER
	serialDteDSR	INTEGER
	serialDteDCD	INTEGER
	serialDteRTS	INTEGER
	serialDteRTSDelay	INTEGER
	serialDteDTR	INTEGER
	serialDteCTS	INTEGER
	serialDteV54	INTEGER
	serialDteLL	INTEGER
	serialDteRL	INTEGER
	serialDteStartChannel	INTEGER
	serialDteNumberOfChannels	INTEGER
	serialDteTxClock	INTEGER
	serialDteBundle	INTEGER
	serialDteChannelRate	INTEGER
	serialDteInvertClock	INTEGER

SerialDteAlarmTableEntry
SEQUENCE
	serialDteAlarmNearIndex	INTEGER
	serialDteAlarmFarIndex	INTEGER
	serialDteAlarmIndex	INTEGER
	serialDteDTRAlarmControl	INTEGER
	serialDteDTRAlarmStatus	INTEGER
	serialDteStatusSummary	DisplayString
	serialDteAlarmSummary	DisplayString
	serialDteASCStatus	INTEGER
	serialDteASCCount	INTEGER
	serialDteASCThreshold	INTEGER
	serialDteASCAlarm	INTEGER
	serialDteFDLStatus	INTEGER
	serialDteFDLCount	INTEGER
	serialDteFDLThreshold	INTEGER
	serialDteFDLAlarm	INTEGER
	serialDteLOSStatus	INTEGER
	serialDteLOSCount	INTEGER
	serialDteLOSThreshold	INTEGER
	serialDteLOSAlarm	INTEGER

AnalogDteTableEntry
SEQUENCE
	analogDteNearIndex	INTEGER
	analogDteFarIndex	INTEGER
	analogDteIndex	INTEGER
	analogDteDescription	DisplayString
	analogDteCardType	INTEGER
	analogDteMode	INTEGER
	analogDteState	INTEGER
	analogDteElementID	DisplayString
	analogDteSignalling	INTEGER
	analogDteDNISDelay	INTEGER
	analogDteTxGain	INTEGER
	analogDteRxGain	INTEGER

ConnectionTableEntry
SEQUENCE
	connectionNearIndex	INTEGER
	connectionFarIndex	INTEGER
	connectionTableIndex	INTEGER
	connectionTableDescription	DisplayString

ConnectionChannelEntry
SEQUENCE
	connectionChannelNearIndex	INTEGER
	connectionChannelFarIndex	INTEGER
	connectionChannelLineIndex	INTEGER
	connectionChannelIndex	INTEGER
	channelInterfaceAssignment	INTEGER
	channelInterfaceDescription	DisplayString
	channelInterfaceChannel	INTEGER
	channelSignalling	INTEGER

BertTableEntry
SEQUENCE
	bertNearIndex	INTEGER
	bertFarIndex	INTEGER
	bertIndex	INTEGER
	bertPattern	INTEGER
	bertLength	INTEGER
	bertPatternSync	INTEGER
	bertElapsedTime	INTEGER
	bertBitErrors	INTEGER
	bertErroredSeconds	INTEGER
	bertPercentEFS	INTEGER
	bertCommand	INTEGER

BertInterfaceTableEntry
SEQUENCE
	bertInterfaceNearIndex	INTEGER
	bertInterfaceFarIndex	INTEGER
	bertChipIndex	INTEGER
	bertInterfaceIndex	INTEGER
	bertInterfaceSetting	INTEGER

TestTableEntry
SEQUENCE
	testNearIndex	INTEGER
	testFarIndex	INTEGER
	testTableIndex	INTEGER
	testType	INTEGER
	testLoopDirection	INTEGER
	testFarLLBFraming	INTEGER

Performance24TableEntry
SEQUENCE
	performance24NearIndex	INTEGER
	performance24FarIndex	INTEGER
	performance24InterfaceIndex	INTEGER
	performance24Index	INTEGER
	performance24ES	INTEGER
	performance24BES	INTEGER
	performance24SES	INTEGER
	performance24UAS	INTEGER
	performance24LOFC	INTEGER
	performance24CSS	INTEGER
	performance24CRCES	INTEGER
	performance24OOFS	INTEGER
	performance24LOSS	INTEGER
	performance24AISS	INTEGER
	performance24RAS	INTEGER
	performance24BPVS	INTEGER

Performance30TableEntry
SEQUENCE
	performance30NearIndex	INTEGER
	performance30FarIndex	INTEGER
	performance30InterfaceIndex	INTEGER
	performance30Index	INTEGER
	performance30ES	INTEGER
	performance30BES	INTEGER
	performance30SES	INTEGER
	performance30UAS	INTEGER
	performance30LOFC	INTEGER
	performance30CSS	INTEGER
	performance30CRCES	INTEGER
	performance30OOFS	INTEGER
	performance30LOSS	INTEGER
	performance30AISS	INTEGER
	performance30RAS	INTEGER
	performance30BPVS	INTEGER

ITableEntry
SEQUENCE
	iTableNearIndex	INTEGER
	iTableFarIndex	INTEGER
	iTableIndex	INTEGER
	iDescription	DisplayString
	iType	INTEGER
	iSlot	INTEGER
	iPort	INTEGER
	iStatus	INTEGER

TraplogEntry
SEQUENCE
	traplogIndex	INTEGER
	traplogNearIndex	INTEGER
	traplogFarIndex	INTEGER
	traplogInterfaceIndex	INTEGER
	traplogTrapNum	INTEGER
	traplogTimeStamp	DisplayString
	traplogDeviceType	INTEGER

UnitUtilitiesTableEntry
SEQUENCE
	unitUtilitiesNearIndex	INTEGER
	unitUtilitiesFarIndex	INTEGER
	unitUtilitiesLocalPassword	DisplayString
	unitUtilitiesTime	DisplayString
	unitUtilitiesDate	DisplayString
	unitUtilitiesMaintenanceReset	INTEGER
	unitUtilitiesAlarmResetTimer	INTEGER
	unitUtilitiesAlarmClear	INTEGER

Defined Values

txport		1.3.6.1.4.1.425
OBJECT IDENTIFIER

companyinfo		1.3.6.1.4.1.425.1
OBJECT IDENTIFIER

products		1.3.6.1.4.1.425.2
OBJECT IDENTIFIER

temporary		1.3.6.1.4.1.425.3
OBJECT IDENTIFIER

traps		1.3.6.1.4.1.425.4
OBJECT IDENTIFIER

revision		1.3.6.1.4.1.425.5
OBJECT IDENTIFIER

pdc		1.3.6.1.4.1.425.6
OBJECT IDENTIFIER

utilities		1.3.6.1.4.1.425.7
OBJECT IDENTIFIER

tinterfaces		1.3.6.1.4.1.425.8
OBJECT IDENTIFIER

mgmtPorts		1.3.6.1.4.1.425.8.1
OBJECT IDENTIFIER

dbu		1.3.6.1.4.1.425.8.2
OBJECT IDENTIFIER

t1e1		1.3.6.1.4.1.425.8.3
OBJECT IDENTIFIER

ddsNet		1.3.6.1.4.1.425.8.4
OBJECT IDENTIFIER

serialDte		1.3.6.1.4.1.425.8.5
OBJECT IDENTIFIER

analogDte		1.3.6.1.4.1.425.8.6
OBJECT IDENTIFIER

connection		1.3.6.1.4.1.425.8.7
OBJECT IDENTIFIER

maintenance		1.3.6.1.4.1.425.8.8
OBJECT IDENTIFIER

performance		1.3.6.1.4.1.425.8.9
OBJECT IDENTIFIER

itable		1.3.6.1.4.1.425.8.10
OBJECT IDENTIFIER

traplog		1.3.6.1.4.1.425.8.11
OBJECT IDENTIFIER

unitUtilities		1.3.6.1.4.1.425.8.12
OBJECT IDENTIFIER

mgmtPortsTable		1.3.6.1.4.1.425.8.1.1
The Management Ports table.
Status: optional	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MgmtPortsTableEntry

mgmtPortsTableEntry		1.3.6.1.4.1.425.8.1.1.1
An entry in the Management Ports table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	MgmtPortsTableEntry

mgmtPortsTableIndex		1.3.6.1.4.1.425.8.1.1.1.1
The index into the Management Ports table.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mgmtPortsDescription		1.3.6.1.4.1.425.8.1.1.1.2
Contains a textual description of the port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..40)

mgmtPortsElementID		1.3.6.1.4.1.425.8.1.1.1.3
This object signifies the name of the device.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..27)

mgmtPortsMode		1.3.6.1.4.1.425.8.1.1.1.4
This object signifies the method used by the port to report alarms.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), disabled(2), coadial(3), coadirect(4), extAlarmOnOpen(5), extAlarmOnClosed(6), slipdial(7), slipdirect(8)

mgmtPortsDialPrefix		1.3.6.1.4.1.425.8.1.1.1.5
This object contains the dial string prefix for a modem connected to the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..38)

mgmtPortsPrimaryDialString		1.3.6.1.4.1.425.8.1.1.1.6
This object contains the primary dial string for a modem connected to the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..30)

mgmtPortsSecondaryDialString		1.3.6.1.4.1.425.8.1.1.1.7
This object contains the secondary dial string for a modem connected to the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..30)

mgmtPortsExtInitString		1.3.6.1.4.1.425.8.1.1.1.8
This object contains the init string for a modem connected to the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..38)

mgmtPortsCompressedSlip		1.3.6.1.4.1.425.8.1.1.1.9
This object specifies if SLIP compression is to be used.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), enabled(2), disabled(3), auto(4)

mgmtPortsInternalModem		1.3.6.1.4.1.425.8.1.1.1.10
This object signifies if the internal modem (when present) is enabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), notPresent(2), enabled(3), disabled(4)

dbuConfigTable		1.3.6.1.4.1.425.8.2.1
The Dial Backup Configuration Table.
Status: optional	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DbuConfigTableEntry

dbuConfigTableEntry		1.3.6.1.4.1.425.8.2.1.1
An entry in the Dial Backup Configuration table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	DbuConfigTableEntry

dbuNearIndex		1.3.6.1.4.1.425.8.2.1.1.1
Selects the near device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dbuFarIndex		1.3.6.1.4.1.425.8.2.1.1.2
Selects the far device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dbuConfigTableIndex		1.3.6.1.4.1.425.8.2.1.1.3
The index into the Dial Backup table.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dbuDescription		1.3.6.1.4.1.425.8.2.1.1.4
Contains a textual description of the dbu.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..40)

dbuRate		1.3.6.1.4.1.425.8.2.1.1.5
This object is the identifier of the current DDS DBU rate. The values mean: dbuRate2400 the DBU interface is operating at 2400bps dbuRate4800 the DBU interface is operating at 4800bps dbuRate9600 the DBU interface is operating at 9600bps dbuRate19200 the DBU interface is operating at 19200bps dbuRate38400 the DBU interface is operating at 38400bps dbuRate56000 the DBU interface is operating at 56000bps dbuRate57600 the DBU interface is operating at 57600bps dbuRate64000 the DBU interface is operating at 64000bps
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	dbuRateOther(1), dbuRate2400(2), dbuRate4800(3), dbuRate9600(4), dbuRate19200(5), dbuRate38400(6), dbuRate56000(7), dbuRate57600(8), dbuRate64000(9)

dbuMode		1.3.6.1.4.1.425.8.2.1.1.6
This object is the identifier of the current mode that the Dial Backup Unit is operating in. The values mean: dbuModeOrig The dial backup unit is operating in the originate mode dbuModeAnsw The dial backup unit is operating in the answer mode dbuModeNotAvail The dial backup unit's mode is not available dbuModeCallbackOrig The dial backup unit is operating in the callback originate mode dbuModeCallbackAnsw The dial backup unit is operating in the callback mode dbuModeMaster The dial backup unit is configured as a master unit dbuModeSlave The dial backup unit is configured as a slave unit
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	dbuModeOther(1), dbuModeOrig(2), dbuModeAnsw(3), dbuModeNotAvail(4), dbuModeCallbackOrig(5), dbuModeCallbackAnsw(6), dbuModeMaster(7), dbuModeSlave(8)

dbuFormat		1.3.6.1.4.1.425.8.2.1.1.7
This object is the identifier of the current format that the Dial Backup Unit is operating in. The values mean: dbuFormatSync The dial backup unit is operating in the synchronous format dbuFormatAsync The dial backup unit is operating in the asynchronous format dbuFormatNotAvail The dial backup unit's format is not available
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	dbuFormatOther(1), dbuFormatSync(2), dbuFormatAsync(3), dbuFormatNotAvail(4)

dbuNumber		1.3.6.1.4.1.425.8.2.1.1.8
This string is the currently programmed number for the dial backup unit to call
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..100)

dbuStatus		1.3.6.1.4.1.425.8.2.1.1.9
This object is the identifier of the current Dial Backup Unit operating status. The values mean: dbuStatusDisabled The dial backup unit is either not installed or disabled dbuStatusEnabled The dial backup unit is installed and enabled dbuStatusActive The dial backup unit is currently active dbuStatusLocked The dial backup unit is in a locked state dbuStatusConnecting The dial backup unit is in the process of connecting dbuStatusDisallowed The dial backup unit is currently not allowed to activate due to the Time Of Day Enable settings dbuStatusAwaitingCall The dial backup unit is in the process of waiting for an incoming call dbuStatusDialing The dial backup unit is in the process of placing a call dbuStatusDisconnecting The dial backup unit is in the process of disconnecting dbuStatusTesting The dial backup unit is in the process of testing dbuStatusTestPassed The dial backup unit has passed a self-test dbuStatusTestFailed The dial backup unit has failed a self-test
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	dbuStatusOther(1), dbuStatusDisabled(2), dbuStatusEnabled(3), dbuStatusActive(4), dbuStatusLocked(5), dbuStatusConnecting(6), dbuStatusDisallowed(7), dbuStatusAwaitingCall(8), dbuStatusDialing(9), dbuStatusDisconnecting(10), dbuStatusTesting(11), dbuStatusTestPassed(12), dbuStatusTestFailed(13)

dbuCommand		1.3.6.1.4.1.425.8.2.1.1.10
This object is the identifier of the current setting that the Dial Backup Unit is operating in. The values mean: dbuCommandDisable The dial backup unit is not to operate dbuCommandEnable The dial backup unit is to operate, subject to Activator and line conditions only dbuCommandActivate The dial backup unit is to operate, irregardless of line conditions dbuCommandLock The dial backup unit is to continue operating, irregardless of line conditions dbuCommandEnableDaily The dial backup unit is to operate, subject to Activator, line conditions, and the Time Of Day Enable fields dbuCommandTest The dial backup unit is commanded to test the link.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	dbuCommandOther(1), dbuCommandDisable(2), dbuCommandEnable(3), dbuCommandActivate(4), dbuCommandLock(5), dbuCommandEnableDaily(6), dbuCommandTest(7)

dbuActivator1		1.3.6.1.4.1.425.8.2.1.1.11
This object is the identifier of the current trigger that will activate the Dial Backup Unit. The values mean: dbuActivatorLOS The dial backup unit is activated by a LOS alarm condition dbuActivatorOOS The dial backup unit is activated by an OOS alarm condition dbuActivatorOOF The dial backup unit is activated by an OOF alarm condition dbuActivatorAny The dial backup unit is activated by a LOS, OOS, or OOF alarm condition dbuActivatorES The dial backup unit is activated by an ES alarm condition dbuActivatorSES The dial backup unit is activated by an SES alarm condition dbuActivatorUAS The dial backup unit is activated by an UAS alarm condition dbuActivatorLOF The dial backup unit is activated by an LOF alarm condition dbuActivatorRAS The dial backup unit is activated by an RAS alarm condition dbuActivatorAIS The dial backup unit is activated by an AIS alarm condition dbuActivatorBPV The dial backup unit is activated by an BPV alarm condition
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	dbuActivatorOther(1), dbuActivatorLOS(2), dbuActivatorOOS(3), dbuActivatorOOF(4), dbuActivatorAny(5), dbuActivatorES(6), dbuActivatorSES(7), dbuActivatorUAS(8), dbuActivatorLOF(9), dbuActivatorRAS(10), dbuActivatorAIS(11), dbuActivatorBPV(12)

dbuActivator2		1.3.6.1.4.1.425.8.2.1.1.12
This object is the identifier of the current trigger that will activate the Dial Backup Unit. The values mean: dbuActivatorLOS The dial backup unit is activated by a LOS alarm condition dbuActivatorOOS The dial backup unit is activated by a OOS alarm condition dbuActivatorOOF The dial backup unit is activated by a OOF alarm condition dbuActivatorAny The dial backup unit is activated by a LOS, OOS, or OOF alarm condition dbuActivatorES The dial backup unit is activated by an ES alarm condition dbuActivatorSES The dial backup unit is activated by an SES alarm condition dbuActivatorUAS The dial backup unit is activated by an UAS alarm condition dbuActivatorLOF The dial backup unit is activated by an LOF alarm condition dbuActivatorRAS The dial backup unit is activated by an RAS alarm condition dbuActivatorAIS The dial backup unit is activated by an AIS alarm condition dbuActivatorBPV The dial backup unit is activated by an BPV alarm condition
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	dbuActivatorOther(1), dbuActivatorLOS(2), dbuActivatorOOS(3), dbuActivatorOOF(4), dbuActivatorAny(5), dbuActivatorES(6), dbuActivatorSES(7), dbuActivatorUAS(8), dbuActivatorLOF(9), dbuActivatorRAS(10), dbuActivatorAIS(11), dbuActivatorBPV(12)

dbuDialStr		1.3.6.1.4.1.425.8.2.1.1.13
This string is the dial string sent to the dial backup unit during every connection attempt
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..50)

dbuInitStr		1.3.6.1.4.1.425.8.2.1.1.14
This string is the initialization string sent to the dial backup unit before every connection attempt
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..50)

dbuHangupStr		1.3.6.1.4.1.425.8.2.1.1.15
This string is the hangup command string sent to the dial backup unit after every successful call
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..50)

dbuPasswordStr		1.3.6.1.4.1.425.8.2.1.1.16
This string is the prompt character and password string for the dial backup unit in Callback DBU
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..8)

dbuSecurity		1.3.6.1.4.1.425.8.2.1.1.17
Enables security on dial backup unit.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	dbuSecurityOther(1), dbuSecurityDisable(2), dbuSecurityEnable(3)

dbuDtrDial		1.3.6.1.4.1.425.8.2.1.1.18
Enables DTR dial feature on dial backup unit.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	dbuDtrDialOther(1), dbuDtrDialDisable(2), dbuDtrDialEnable(3)

dbuISDNSwitchType		1.3.6.1.4.1.425.8.2.1.1.19
Specifies the switch type for the ISDN DBU.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

dbuISDNSwitchVersion		1.3.6.1.4.1.425.8.2.1.1.20
Specifies the switch version for the ISDN DBU.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	dbuISDNSwitchVersionOther(1), dbuISDNSwitchVersionNational1(2), dbuISDNSwitchVersionATTP2P(3), dbuISDNSwitchVersionATTMP(4), dbuISDNSwitchVersionDMS100PVCIC0(5), dbuISDNSwitchVersionDMS100PVCIC1(6)

dbuISDNTEI		1.3.6.1.4.1.425.8.2.1.1.21
Specifies the ISDN DBU TEI.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	dbuISDNTEIOther(1), dbuISDNTEIDisable(2), dbuISDNTEIAuto(3), dbuISDNTEI0(4), dbuISDNTEI1(5), dbuISDNTEI2(6), dbuISDNTEI3(7), dbuISDNTEI4(8), dbuISDNTEI5(9), dbuISDNTEI6(10), dbuISDNTEI7(11), dbuISDNTEI8(12), dbuISDNTEI9(13), dbuISDNTEI10(14), dbuISDNTEI11(15), dbuISDNTEI12(16), dbuISDNTEI13(17), dbuISDNTEI14(18), dbuISDNTEI15(19), dbuISDNTEI16(20), dbuISDNTEI17(21), dbuISDNTEI18(22), dbuISDNTEI19(23), dbuISDNTEI20(24), dbuISDNTEI21(25), dbuISDNTEI22(26), dbuISDNTEI23(27), dbuISDNTEI24(28), dbuISDNTEI25(29), dbuISDNTEI26(30), dbuISDNTEI27(31), dbuISDNTEI28(32), dbuISDNTEI29(33), dbuISDNTEI30(34), dbuISDNTEI31(35), dbuISDNTEI32(36), dbuISDNTEI33(37), dbuISDNTEI34(38), dbuISDNTEI35(39), dbuISDNTEI36(40), dbuISDNTEI37(41), dbuISDNTEI38(42), dbuISDNTEI39(43), dbuISDNTEI40(44), dbuISDNTEI41(45), dbuISDNTEI42(46), dbuISDNTEI43(47), dbuISDNTEI44(48), dbuISDNTEI45(49), dbuISDNTEI46(50), dbuISDNTEI47(51), dbuISDNTEI48(52), dbuISDNTEI49(53), dbuISDNTEI50(54), dbuISDNTEI51(55), dbuISDNTEI52(56), dbuISDNTEI53(57), dbuISDNTEI54(58), dbuISDNTEI55(59), dbuISDNTEI56(60), dbuISDNTEI57(61), dbuISDNTEI58(62), dbuISDNTEI59(63), dbuISDNTEI60(64), dbuISDNTEI61(65), dbuISDNTEI62(66), dbuISDNTEI63(67)

dbuISDNSPID		1.3.6.1.4.1.425.8.2.1.1.22
Specifies the SPID for the ISDN DBU.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

dbuISDNDDNUM		1.3.6.1.4.1.425.8.2.1.1.23
Specifies the Data Directory Number for the ISDN DBU.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

dbuResetStringsTable		1.3.6.1.4.1.425.8.2.2
A table of COLD START reprogramming strings for the dial backup unit.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DbuResetStringsEntry

dbuResetStringsEntry		1.3.6.1.4.1.425.8.2.2.1
An entry in the dbuResetStringsTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	DbuResetStringsEntry

dbuResetNearIndex		1.3.6.1.4.1.425.8.2.2.1.1
Selects the near device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dbuResetFarIndex		1.3.6.1.4.1.425.8.2.2.1.2
Selects the far device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dbuResetConfigEntryIndex		1.3.6.1.4.1.425.8.2.2.1.3
The index into the Dial Backup table.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dbuResetStringsIndex		1.3.6.1.4.1.425.8.2.2.1.4
The index into the dbuResetStringsTable.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dbuResetString		1.3.6.1.4.1.425.8.2.2.1.5
This string is one of the dial backup unit's COLD START reprogramming strings
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..50)

dbuStartStopTable		1.3.6.1.4.1.425.8.2.3
The Dial Backup StartStop Table.
Status: optional	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DbuStartStopTableEntry

dbuStartStopTableEntry		1.3.6.1.4.1.425.8.2.3.1
An entry in the Dial Backup Start Stop table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	DbuStartStopTableEntry

dbuStartStopNearIndex		1.3.6.1.4.1.425.8.2.3.1.1
Selects the near device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dbuStartStopFarIndex		1.3.6.1.4.1.425.8.2.3.1.2
Selects the far device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dbuStartStopConfigEntryIndex		1.3.6.1.4.1.425.8.2.3.1.3
The index into the Dial Backup table.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

dbuStartStopDayOfWeek		1.3.6.1.4.1.425.8.2.3.1.4
The index into the Dial Backup Start Stop times table.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	dbuStartStopSunday(1), dbuStartStopMonday(2), dbuStartStopTuesday(3), dbuStartStopWednesday(4), dbuStartStopThursday(5), dbuStartStopFriday(6), dbuStartStopSaturday(7)

dbuStart		1.3.6.1.4.1.425.8.2.3.1.5
This object is the beginning of an allowable window for Dial Backup Activation.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	dbuStartHour00(1), dbuStartHour01(2), dbuStartHour02(3), dbuStartHour03(4), dbuStartHour04(5), dbuStartHour05(6), dbuStartHour06(7), dbuStartHour07(8), dbuStartHour08(9), dbuStartHour09(10), dbuStartHour10(11), dbuStartHour11(12), dbuStartHour12(13), dbuStartHour13(14), dbuStartHour14(15), dbuStartHour15(16), dbuStartHour16(17), dbuStartHour17(18), dbuStartHour18(19), dbuStartHour19(20), dbuStartHour20(21), dbuStartHour21(22), dbuStartHour22(23), dbuStartHour23(24)

dbuStop		1.3.6.1.4.1.425.8.2.3.1.6
This object is the end of an allowable window for Dial Backup Activation.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	dbuStopHour00(1), dbuStopHour01(2), dbuStopHour02(3), dbuStopHour03(4), dbuStopHour04(5), dbuStopHour05(6), dbuStopHour06(7), dbuStopHour07(8), dbuStopHour08(9), dbuStopHour09(10), dbuStopHour10(11), dbuStopHour11(12), dbuStopHour12(13), dbuStopHour13(14), dbuStopHour14(15), dbuStopHour15(16), dbuStopHour16(17), dbuStopHour17(18), dbuStopHour18(19), dbuStopHour19(20), dbuStopHour20(21), dbuStopHour21(22), dbuStopHour22(23), dbuStopHour23(24)

t1e1ConfigTable		1.3.6.1.4.1.425.8.3.1
The T1 and E1 Configuration Table.
Status: optional	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		T1e1ConfigTableEntry

t1e1ConfigTableEntry		1.3.6.1.4.1.425.8.3.1.1
An entry in the t1e1Table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	T1e1ConfigTableEntry

t1e1ConfigNearIndex		1.3.6.1.4.1.425.8.3.1.1.1
Selects the near device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

t1e1ConfigFarIndex		1.3.6.1.4.1.425.8.3.1.1.2
Selects the far device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

t1e1ConfigIndex		1.3.6.1.4.1.425.8.3.1.1.3
This object is the index into the t1e1Table.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

t1e1Description		1.3.6.1.4.1.425.8.3.1.1.4
Contains a textual description of the port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..40)

t1e1Mode		1.3.6.1.4.1.425.8.3.1.1.5
This object identifies the port as either a Network (long-haul) or DTE (short-haul) port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	t1e1ModeOther(1), t1e1ModeDTE(2), t1e1ModeNetwork(3)

t1e1FrameType		1.3.6.1.4.1.425.8.3.1.1.6
Selects the framing for the network side of the DSU/CSU.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	t1e1FrameTypeOther(1), t1e1FrameTypeESF(2), t1e1FrameTypeD4(3), t1e1FrameTypeCCSCRC(4), t1e1FrameTypeCCS(5), t1e1FrameTypeCAS(6), t1e1FrameTypeCASCRC(7), t1e1FrameTypeUnframed(8)

t1e1LineCode		1.3.6.1.4.1.425.8.3.1.1.7
Selects the network side line coding.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	t1e1LineCodeOther(1), t1e1LineCodeAMI(2), t1e1LineCodeB8ZS(3), t1e1LineCodeHDB3(4)

t1e1LineBuildOut		1.3.6.1.4.1.425.8.3.1.1.8
Selects the line build out for the network interface. The options are: t1e1LineBuildOut0db indicates a line build out of 0db t1e1LineBuildOut75db indicates a line build out of -7.5db t1e1LineBuildOut15db indicates a line build out of -15db t1e1LineBuildOut225db indicates a line build out of -22.5db
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	t1e1LineBuildOutOther(1), t1e1LineBuildOut0db(2), t1e1LineBuildOut75db(3), t1e1LineBuildOut15db(4), t1e1LineBuildOut225db(5)

t1e1Timing		1.3.6.1.4.1.425.8.3.1.1.9
Sets the timing source to synchronize the unit's internal timing generators.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	t1e1TimingOther(1), t1e1TimingInternal(2), t1e1TimingNetwork(3), t1e1TimingT1DTE(4), t1e1TimingStation(5), t1e1TimingStaClock(6), t1e1TimingPort1(7), t1e1TimingPort2(8), t1e1TimingPort3(9), t1e1TimingPort4(10), t1e1TimingPort5(11), t1e1TimingPort6(12), t1e1TimingPort7(13), t1e1TimingPort8(14), t1e1TimingPort9(15), t1e1TimingPort10(16), t1e1TimingPort11(17), t1e1TimingPort12(18), t1e1TimingPort13(19), t1e1TimingPort14(20), t1e1TimingPort15(21), t1e1TimingPort16(22), t1e1TimingPort17(23), t1e1TimingPort18(24), t1e1TimingPort19(25), t1e1TimingPort20(26), t1e1TimingPort21(27), t1e1TimingPort22(28), t1e1TimingPort23(29), t1e1TimingPort24(30), t1e1TimingPort25(31), t1e1TimingPort26(32), t1e1TimingPort27(33), t1e1TimingPort28(34), t1e1TimingPort29(35), t1e1TimingPort30(36), t1e1TimingPort31(37), t1e1TimingPort32(38), t1e1TimingSlot2PortA(39), t1e1TimingSlot2PortB(40), t1e1TimingSlot3PortA(41), t1e1TimingSlot3PortB(42), t1e1TimingSlot4PortA(43), t1e1TimingSlot4PortB(44), t1e1TimingSlot5PortA(45), t1e1TimingSlot5PortB(46), t1e1TimingSlot6PortA(47), t1e1TimingSlot6PortB(48), t1e1TimingSlot2Dsu1PortA(49), t1e1TimingSlot2Dsu1PortB(50), t1e1TimingSlot2Dsu2PortA(51), t1e1TimingSlot2Dsu2PortB(52), t1e1TimingSlot2Dsu3PortA(53), t1e1TimingSlot2Dsu3PortB(54), t1e1TimingSlot2Dsu4PortA(55), t1e1TimingSlot2Dsu4PortB(56), t1e1TimingSlot2Dsu5PortA(57), t1e1TimingSlot2Dsu5PortB(58), t1e1TimingSlot2Dsu6PortA(59), t1e1TimingSlot2Dsu6PortB(60), t1e1TimingSlot3Dsu1PortA(61), t1e1TimingSlot3Dsu1PortB(62), t1e1TimingSlot3Dsu2PortA(63), t1e1TimingSlot3Dsu2PortB(64), t1e1TimingSlot3Dsu3PortA(65), t1e1TimingSlot3Dsu3PortB(66), t1e1TimingSlot3Dsu4PortA(67), t1e1TimingSlot3Dsu4PortB(68), t1e1TimingSlot3Dsu5PortA(69), t1e1TimingSlot3Dsu5PortB(70), t1e1TimingSlot3Dsu6PortA(71), t1e1TimingSlot3Dsu6PortB(72), t1e1TimingSlot4Dsu1PortA(73), t1e1TimingSlot4Dsu1PortB(74), t1e1TimingSlot4Dsu2PortA(75), t1e1TimingSlot4Dsu2PortB(76), t1e1TimingSlot4Dsu3PortA(77), t1e1TimingSlot4Dsu3PortB(78), t1e1TimingSlot4Dsu4PortA(79), t1e1TimingSlot4Dsu4PortB(80), t1e1TimingSlot4Dsu5PortA(81), t1e1TimingSlot4Dsu5PortB(82), t1e1TimingSlot4Dsu6PortA(83), t1e1TimingSlot4Dsu6PortB(84), t1e1TimingSlot5Dsu1PortA(85), t1e1TimingSlot5Dsu1PortB(86), t1e1TimingSlot5Dsu2PortA(87), t1e1TimingSlot5Dsu2PortB(88), t1e1TimingSlot5Dsu3PortA(89), t1e1TimingSlot5Dsu3PortB(90), t1e1TimingSlot5Dsu4PortA(91), t1e1TimingSlot5Dsu4PortB(92), t1e1TimingSlot5Dsu5PortA(93), t1e1TimingSlot5Dsu5PortB(94), t1e1TimingSlot5Dsu6PortA(95), t1e1TimingSlot5Dsu6PortB(96), t1e1TimingSlot6Dsu1PortA(97), t1e1TimingSlot6Dsu1PortB(98), t1e1TimingSlot6Dsu2PortA(99), t1e1TimingSlot6Dsu2PortB(100), t1e1TimingSlot6Dsu3PortA(101), t1e1TimingSlot6Dsu3PortB(102), t1e1TimingSlot6Dsu4PortA(103), t1e1TimingSlot6Dsu4PortB(104), t1e1TimingSlot6Dsu5PortA(105), t1e1TimingSlot6Dsu5PortB(106), t1e1TimingSlot6Dsu6PortA(107), t1e1TimingSlot6Dsu6PortB(108)

t1e1StationInTiming		1.3.6.1.4.1.425.8.3.1.1.10
Selects the input timing if t1e1Timing is set to Station.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	t1e1StationInTimingOther(1), t1e1StationInTimingNX56(2), t1e1StationInTimingNX64(3), t1e1StationInTiming1544(4), t1e1StationInTiming2048(5)

t1e1StationTiming		1.3.6.1.4.1.425.8.3.1.1.11
Selects the N-multiple when Station Input Timing is set to either NX56 or NX65. The N range is 1..24
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

t1e1PRM		1.3.6.1.4.1.425.8.3.1.1.12
Enables the ANSI T1.403 Performance Report Message functions.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	t1e1PRMOther(1), t1e1PRMDisable(2), t1e1PRMEnable(3)

t1e1ZeroSuppress		1.3.6.1.4.1.425.8.3.1.1.13
Determines whether ones density insertion is activated after 15 zeros . To ensure compliance with TR54016, this field must be enabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	t1e1ZeroOther(1), t1e1ZeroDisable(2), t1e1ZeroEnable(3)

t1e1NationalBit		1.3.6.1.4.1.425.8.3.1.1.14
Selects a national bit to create a 4-kpbs datalink between the endpoint units.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	t1e1NationalOther(1), t1e1NationalNone(2), t1e1NationalSA4(3), t1e1NationalSA5(4), t1e1NationalSA6(5), t1e1NationalSA7(6), t1e1NationalSA8(7)

t1e1KeepAlive		1.3.6.1.4.1.425.8.3.1.1.15
Selects keep alive framed and unframed ones when the unit detects LOS or OOF.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	t1e1KeepAliveOther(1), t1e1KeepAliveUnframedOnes(2), t1e1KeepAliveFramedOnes(3), t1e1KeepAliveLoop(4)

t1e1CRC4Mode		1.3.6.1.4.1.425.8.3.1.1.16
Selects whether CRC4 is enabled or disabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	t1e1CRC4Other(1), t1e1CRC4Disabled(2), t1e1CRC4Enabled(3)

t1e1DSXLevel		1.3.6.1.4.1.425.8.3.1.1.17
Selects the DSX1 interface output level.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	t1e1DSXOther(1), t1e1DSX0110(2), t1e1DSX111220(3), t1e1DSX221330(4), t1e1DSX331440(5), t1e1DSX441550(6), t1e1DSX551660(7), t1e1DSX661up(8)

t1e1CRC		1.3.6.1.4.1.425.8.3.1.1.18
Determines whether received CRC data is passed through or regenerated.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	t1e1CRCOther(1), t1e1CRCPass(2), t1e1CRCRegenerate(3)

t1e1FDLPassThrough		1.3.6.1.4.1.425.8.3.1.1.19
Determines whether the ESF FDL passes through the CSU or terminates.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	t1e1FDLPassThroughOther(1), t1e1FDLPassThroughPass(2), t1e1FDLPassThroughTerminate(3)

t1e1AudibleAlarm		1.3.6.1.4.1.425.8.3.1.1.20
If applicable, Enables or Disables the CSU's internal buzzer which alerts users of an alarm condition.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	t1e1AudibleAlarmOther(1), t1e1AudibleAlarmDisabled(2), t1e1AudibleAlarmEnabled(3)

t1e1AlarmTable		1.3.6.1.4.1.425.8.3.2
The T1 and E1 Alarm Table.
Status: optional	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		T1e1AlarmTableEntry

t1e1AlarmTableEntry		1.3.6.1.4.1.425.8.3.2.1
An entry in the t1e1Table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	T1e1AlarmTableEntry

t1e1AlarmNearIndex		1.3.6.1.4.1.425.8.3.2.1.1
Selects the near device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

t1e1AlarmFarIndex		1.3.6.1.4.1.425.8.3.2.1.2
Selects the far device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

t1e1AlarmIndex		1.3.6.1.4.1.425.8.3.2.1.3
This object is the index into the t1e1Table.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

t1e1StatusSummary		1.3.6.1.4.1.425.8.3.2.1.4
This object provides a summary of the port status.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

t1e1AlarmSummary		1.3.6.1.4.1.425.8.3.2.1.5
This object provides a summary of the port alarms.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

t1e1ESStatus		1.3.6.1.4.1.425.8.3.2.1.6
Reports if a Errorred Seconds condition exists.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	t1e1StatusOther(1), t1e1StatusNoES(2), t1e1StatusES(3)

t1e1ESCount		1.3.6.1.4.1.425.8.3.2.1.7
This count contains the number of consecutive seconds an Errored Seconds condition has existed.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

t1e1ESThreshold		1.3.6.1.4.1.425.8.3.2.1.8
Sets the Errored Seconds alarm threshold. Setting this field to 0 disables the alarm. The threshold can be set to any value in the range 0 to 900.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

t1e1ESAlarm		1.3.6.1.4.1.425.8.3.2.1.9
This status indicates if the Errors Seconds threshold is exceeded.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	t1e1ESAlarmOther(1), t1e1ESAlarmNone(2), t1e1ESAlarmThresholdExceeded(3)

t1e1SESStatus		1.3.6.1.4.1.425.8.3.2.1.10
Reports if a Severely Errorred condition exists.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	t1e1StatusOther(1), t1e1StatusNoSES(2), t1e1StatusSES(3)

t1e1SESCount		1.3.6.1.4.1.425.8.3.2.1.11
This count contains the number of consecutive seconds a Severely Errored condition has existed.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

t1e1SESThreshold		1.3.6.1.4.1.425.8.3.2.1.12
Sets the Severely Errored seconds alarm threshold. Setting this field to 0 disables the alarm. The threshold can be set to any value in the range 0 to 900.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

t1e1SESAlarm		1.3.6.1.4.1.425.8.3.2.1.13
This status indicates if the Severely Errors Seconds threshold is exceeded.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	t1e1SESAlarmOther(1), t1e1SESAlarmNone(2), t1e1SESAlarmThresholdExceeded(3)

t1e1LOSSStatus		1.3.6.1.4.1.425.8.3.2.1.14
Reports if a Loss of Signal condition exists.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	t1e1StatusOther(1), t1e1StatusNoLOSS(2), t1e1StatusLOSS(3)

t1e1LOSSCount		1.3.6.1.4.1.425.8.3.2.1.15
This count contains the number of consecutive seconds a Loss of Signal condition has existed.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

t1e1LOSSThreshold		1.3.6.1.4.1.425.8.3.2.1.16
Sets the Loss of Signal seconds alarm threshold. Setting this field to 0 disables the alarm. The threshold can be set to any value in the range 0 to 900.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

t1e1LOSSAlarm		1.3.6.1.4.1.425.8.3.2.1.17
This status indicates if the Loss of Signal Seconds threshold is exceeded.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	t1e1LOSSAlarmOther(1), t1e1LOSSAlarmNone(2), t1e1LOSSAlarmThresholdExceeded(3)

t1e1UASStatus		1.3.6.1.4.1.425.8.3.2.1.18
Reports if an Unavailable condition exists.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	t1e1StatusOther(1), t1e1StatusNoUAS(2), t1e1StatusUAS(3)

t1e1UASCount		1.3.6.1.4.1.425.8.3.2.1.19
This count contains the number of consecutive seconds an Unavailable condition has existed.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

t1e1UASThreshold		1.3.6.1.4.1.425.8.3.2.1.20
Sets the unavailable seconds alarm threshold. Setting this field to 0 disables the alarm. The threshold can be set to any value in the range 0 to 900.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

t1e1UASAlarm		1.3.6.1.4.1.425.8.3.2.1.21
This status indicates if the Unavailable Seconds threshold is exceeded.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	t1e1UASAlarmOther(1), t1e1UASAlarmNone(2), t1e1UASAlarmThresholdExceeded(3)

t1e1CSSStatus		1.3.6.1.4.1.425.8.3.2.1.22
Reports if a Controlled Slip condition exists.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	t1e1StatusOther(1), t1e1StatusNoCSS(2), t1e1StatusCSS(3)

t1e1CSSCount		1.3.6.1.4.1.425.8.3.2.1.23
This count contains the number of consecutive seconds in which at least one Controlled Slip occurred.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

t1e1CSSThreshold		1.3.6.1.4.1.425.8.3.2.1.24
Sets the Controlled Slip seconds alarm threshold. Setting this field to 0 disables the alarm. The threshold can be set to any value in the range 0 to 900.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

t1e1CSSAlarm		1.3.6.1.4.1.425.8.3.2.1.25
This status indicates if the Controlled Slip seconds threshold is exceeded.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	t1e1CSSAlarmOther(1), t1e1CSSAlarmNone(2), t1e1CSSAlarmThresholdExceeded(3)

t1e1BPVSStatus		1.3.6.1.4.1.425.8.3.2.1.26
Reports if a Bipolar Violation Error condition exists.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	t1e1StatusOther(1), t1e1StatusNoBPVS(2), t1e1StatusBPVS(3)

t1e1BPVSCount		1.3.6.1.4.1.425.8.3.2.1.27
This count contains the number of consecutive seconds a Bipolar Violation Error condition has existed.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

t1e1BPVSThreshold		1.3.6.1.4.1.425.8.3.2.1.28
Sets the Bipolar Violation Error seconds alarm threshold. Setting this field to 0 disables the alarm. The threshold can be set to any value in the range 0 to 900.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

t1e1BPVSAlarm		1.3.6.1.4.1.425.8.3.2.1.29
This status indicates if the Bipolar Violation Error seconds threshold is exceeded.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	t1e1BPVSAlarmOther(1), t1e1BPVSAlarmNone(2), t1e1BPVSAlarmThresholdExceeded(3)

t1e1OOFSStatus		1.3.6.1.4.1.425.8.3.2.1.30
Indicates that the unit is unable to synchronize on the incoming framing pattern.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	t1e1StatusOther(1), t1e1StatusNoOOF(2), t1e1StatusOOF(3)

t1e1OOFSCount		1.3.6.1.4.1.425.8.3.2.1.31
This count contains the number of consecutive seconds an OOF condition has existed.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

t1e1OOFSThreshold		1.3.6.1.4.1.425.8.3.2.1.32
Sets the OOF seconds alarm threshold. Setting this field to 0 disables the alarm. The threshold can be set to any value in the range 0 to 900.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

t1e1OOFSAlarm		1.3.6.1.4.1.425.8.3.2.1.33
Indicates if an OOF seconds alarm condition exists.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	t1e1OOFSAlarmOther(1), t1e1OOFSAlarmNone(2), t1e1OOFSAlarmExists(3)

t1e1AISStatus		1.3.6.1.4.1.425.8.3.2.1.34
Indicates that the unit is receiving an unframed all ones pattern.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	t1e1StatusOther(1), t1e1StatusNoAIS(2), t1e1StatusAIS(3)

t1e1AISCount		1.3.6.1.4.1.425.8.3.2.1.35
This count contains the number of consecutive seconds an Unframed All Ones condition has existed.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

t1e1AISThreshold		1.3.6.1.4.1.425.8.3.2.1.36
Sets the AIS seconds alarm threshold. Setting this field to 0 disables the alarm. The threshold can be set to any value in the range 0 to 900.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

t1e1AISAlarm		1.3.6.1.4.1.425.8.3.2.1.37
Indicates if an Unframed All Ones alarm condition exists.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	t1e1AISAlarmOther(1), t1e1AISAlarmNone(2), t1e1AISAlarmExists(3)

t1e1RASStatus		1.3.6.1.4.1.425.8.3.2.1.38
Reports if a Remote (Yellow) Alarm condition exists.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	t1e1RASStatusOther(1), t1e1RASStatusNoRAS(2), t1e1RASStatusRAS(3)

t1e1RASCount		1.3.6.1.4.1.425.8.3.2.1.39
This count contains the number of consecutive seconds a Remote (Yellow) Alarm condition has existed.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

t1e1RASThreshold		1.3.6.1.4.1.425.8.3.2.1.40
Sets the RAS seconds alarm threshold. Setting this field to 0 disables the alarm. The threshold can be set to any value in the range 0 to 900.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

t1e1RASAlarm		1.3.6.1.4.1.425.8.3.2.1.41
This status indicates if a Remote (Yellow) Alarm exists.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	t1e1RASAlarmOther(1), t1e1RASAlarmNone(2), t1e1RASAlarmExists(3)

t1e1AlarmResetTimer		1.3.6.1.4.1.425.8.3.2.1.42
Sets the Alarm Reset Timer, this field can be set to any value in the range 0 to 900.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

t1e1AlarmReset		1.3.6.1.4.1.425.8.3.2.1.43
This is used to clear the current alarm counts.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	t1e1AlarmResetOther(1), t1e1AlarmResetClearAlarms(2)

ddsNetConfigTable		1.3.6.1.4.1.425.8.4.1
The dds Network Interface Configuration Table.
Status: optional	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DdsNetConfigTableEntry

ddsNetConfigTableEntry		1.3.6.1.4.1.425.8.4.1.1
An entry in the Network Interface Table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	DdsNetConfigTableEntry

ddsNetConfigNearIndex		1.3.6.1.4.1.425.8.4.1.1.1
Selects the near device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

ddsNetConfigFarIndex		1.3.6.1.4.1.425.8.4.1.1.2
Selects the far device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

ddsNetConfigIndex		1.3.6.1.4.1.425.8.4.1.1.3
Index into the ddsNetConfigTable.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

ddsNetDescription		1.3.6.1.4.1.425.8.4.1.1.4
Contains a textual description of the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..40)

ddsNetRate		1.3.6.1.4.1.425.8.4.1.1.5
This object is the identifier of the current DDS network rate. The values mean: ddsNetRate2400 the DDS network interface is operating at 2400bps ddsNetRate4800 the DDS network interface is operating at 4800bps ddsNetRate9600 the DDS network interface is operating at 9600bps ddsNetRate19200 the DDS network interface is operating at 19200bps ddsNetRate38400 the DDS network interface is operating at 38400bps ddsNetRate56000 the DDS network interface is operating at 56000bps ddsNetRate64000 the DDS network interface is operating at 64000bps
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ddsNetRate2400(1), ddsNetRate4800(2), ddsNetRate9600(3), ddsNetRate19200(4), ddsNetRate38400(5), ddsNetRate56000(6), ddsNetRate64000(7)

ddsNetMode		1.3.6.1.4.1.425.8.4.1.1.6
This variable describes mode in which data is being sent from the DDS unit back towards the network. Changing the value of this variable can cause a loss of remote communications. The values mean: ddsNetModeNormal (DDS-I) normal data mode of operation ddsNetModeProprietaryTXPI (DDS-I) data being sent out on the DDS network is in a proprietary mode to allow for remote communications, rate adaption, and SYNC to ASYNC modes ddsNetMode64KClearChannel (DDS-II) A special case of DDS-II, where the line rate is 72K, the data rate is 64K, and there is no secondary channel. ddsNetMode64KCCProprietaryTXPII (DDS-II) A special case of DDS-II, where the line rate is 72K, the data rate is 64K, and there is no secondary channel. In addition, the data being sent out on the DDS network is in a proprietary mode to allow for remote communications, rate adaption, SYNC to ASYNC, and/or TDM modes.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ddsNetModeNormal(1), ddsNetModeProprietaryTXPI(2), ddsNetMode64KClearChannel(3), ddsNetMode64KCCProprietaryTXPII(4)

ddsNetTimingSource		1.3.6.1.4.1.425.8.4.1.1.7
This variable describes the current timing source for the DDS network interface. The values mean: ddsNetTimingNet unit dependant upon network for DDS network interface timing ddsNetTimingInt unit supplying timing for DDS network interface ddsNetTimingDTE unit dependant upon DTE device for network interface timing
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ddsNetTimingNet(1), ddsNetTimingInt(2), ddsNetTimingDTE(3)

ddsNetRemComm		1.3.6.1.4.1.425.8.4.1.1.8
This variable describes the current setting for the remote communications link. The values mean: ddsNetRemCommEnabled remote communications can be carried out end to end ddsNetRemCommDisabled remote communications are not allowed ddsNetRemCommNotAvailable this unit does not support remote communications
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ddsNetRemCommEnabled(1), ddsNetRemCommDisabled(2), ddsNetRemCommNotAvailable(3)

ddsNetCircuitAssur		1.3.6.1.4.1.425.8.4.1.1.9
This variable describes the current setting for the circuit assurance option. The values mean: ddsNetCircuitAssurEnabled Circuit Assurance is enabled and the integrity of the DDS loop will be maintained ddsNetCircuitAssurDisabled Circuit Assurance is disabled ddsNetCircuitAssurNotAvailable this unit does not support Circuit Assurance
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ddsNetCircuitAssurEnabled(1), ddsNetCircuitAssurDisabled(2), ddsNetCircuitAssurNotAvailable(3)

ddsNetAntiStrTimer		1.3.6.1.4.1.425.8.4.1.1.10
This variable describes the current setting for the anti streaming timer. The values mean: ddsNetAntiStrTimerOff the AntiStreaming Timer is off ddsNetAntiStrTimer10 the AntiStreaming Timer is set to 10 seconds ddsNetAntiStrTimer30 the AntiStreaming Timer is set to 30 seconds ddsNetAntiStrTimer60 ths AntiStreaming Timer is set to 60 seconds
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ddsNetAntiStrTimerOff(1), ddsNetAntiStrTimer10(2), ddsNetAntiStrTimer30(3), ddsNetAntiStrTimer60(4)

ddsNetAlarmTable		1.3.6.1.4.1.425.8.4.2
The dds Network Interface Alarm Table.
Status: optional	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DdsNetAlarmTableEntry

ddsNetAlarmTableEntry		1.3.6.1.4.1.425.8.4.2.1
An entry in the ddsNetAlarmTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	DdsNetAlarmTableEntry

ddsNetAlarmNearIndex		1.3.6.1.4.1.425.8.4.2.1.1
Selects the near device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

ddsNetAlarmFarIndex		1.3.6.1.4.1.425.8.4.2.1.2
Selects the far device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

ddsNetAlarmIndex		1.3.6.1.4.1.425.8.4.2.1.3
Index into the ddsNetAlarmTable.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

ddsNetStatusSummary		1.3.6.1.4.1.425.8.4.2.1.4
This object provides a summary of the port status.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

ddsNetAlarmSummary		1.3.6.1.4.1.425.8.4.2.1.5
This object provides a summary of the port alarms.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

ddsNetLOSStatus		1.3.6.1.4.1.425.8.4.2.1.6
Reports if a Loss of Signal condition exists.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ddsNetStatusLOSOther(1), ddsNetStatusNoLOS(2), ddsNetStatusLOS(3)

ddsNetLOSCount		1.3.6.1.4.1.425.8.4.2.1.7
This count contains the number of consecutive seconds the unit received signal has been interrupted.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

ddsNetLOSThreshold		1.3.6.1.4.1.425.8.4.2.1.8
A period, measured in seconds, in which the DDS received signal is interrupted.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ddsNetLOSThresholdOther(1), ddsNetLOSThresholdNone(2), ddsNetLOSThreshold1(3), ddsNetLOSThreshold2(4), ddsNetLOSThreshold3(5), ddsNetLOSThreshold4(6), ddsNetLOSThreshold5(7), ddsNetLOSThreshold10(8), ddsNetLOSThreshold20(9), ddsNetLOSThreshold30(10)

ddsNetLOSAlarm		1.3.6.1.4.1.425.8.4.2.1.9
This status indicates if the Loss of Signal Seconds threshold is exceeded.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ddsNetLOSAlarmOther(1), ddsNetLOSAlarmNone(2), ddsNetLOSAlarmThresholdExceeded(3)

ddsNetOOFStatus		1.3.6.1.4.1.425.8.4.2.1.10
Reports if an Out of Frame condition exists.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ddsNetStatusOOFOther(1), ddsNetStatusNoOOF(2), ddsNetStatusOOF(3)

ddsNetOOFCount		1.3.6.1.4.1.425.8.4.2.1.11
This count contains the number of consecutive seconds the unit has received the out of frame code.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

ddsNetOOFThreshold		1.3.6.1.4.1.425.8.4.2.1.12
A period, measured in seconds, in which the Out Of Frame code is received or a frame sync loss occurred.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ddsNetOOFThresholdOther(1), ddsNetOOFThresholdNone(2), ddsNetOOFThreshold1(3), ddsNetOOFThreshold2(4), ddsNetOOFThreshold3(5), ddsNetOOFThreshold4(6), ddsNetOOFThreshold5(7), ddsNetOOFThreshold10(8), ddsNetOOFThreshold20(9), ddsNetOOFThreshold30(10)

ddsNetOOFAlarm		1.3.6.1.4.1.425.8.4.2.1.13
This status indicates if the Out of Frame Seconds threshold is exceeded.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ddsNetOOFSAlarmOther(1), ddsNetOOFSAlarmNone(2), ddsNetOOFSAlarmThresholdExceeded(3)

ddsNetOOSStatus		1.3.6.1.4.1.425.8.4.2.1.14
Reports if Out of Service codes are received.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ddsNetStatusOOSOther(1), ddsNetStatusNoOOS(2), ddsNetStatusOOS(3)

ddsNetOOSCount		1.3.6.1.4.1.425.8.4.2.1.15
This count contains the number of consecutive seconds the unit has received the out of service code.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

ddsNetOOSThreshold		1.3.6.1.4.1.425.8.4.2.1.16
A period, measured in seconds, in which the Out Of Service code is received.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ddsNetOOSThresholdOther(1), ddsNetOOSThresholdNone(2), ddsNetOOSThreshold1(3), ddsNetOOSThreshold2(4), ddsNetOOSThreshold3(5), ddsNetOOSThreshold4(6), ddsNetOOSThreshold5(7), ddsNetOOSThreshold10(8), ddsNetOOSThreshold20(9), ddsNetOOSThreshold30(10)

ddsNetOOSAlarm		1.3.6.1.4.1.425.8.4.2.1.17
This status indicates if the Out of Service Seconds threshold is exceeded.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ddsNetOOSAlarmOther(1), ddsNetOOSAlarmNone(2), ddsNetOOSAlarmThresholdExceeded(3)

ddsNetFDLStatus		1.3.6.1.4.1.425.8.4.2.1.18
Reports if Facility Data Link errors have occurred.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ddsNetStatusFDLOther(1), ddsNetStatusNoFDL(2), ddsNetStatusFDL(3)

ddsNetFDLCount		1.3.6.1.4.1.425.8.4.2.1.19
This count contains the number of consecutive seconds in which FDL errors have occurred.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

ddsNetFDLThreshold		1.3.6.1.4.1.425.8.4.2.1.20
A period, measured in seconds, in which FDL errors have occurred.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ddsNetFDLThresholdOther(1), ddsNetFDLThresholdNone(2), ddsNetFDLThreshold1(3), ddsNetFDLThreshold2(4), ddsNetFDLThreshold3(5), ddsNetFDLThreshold4(6), ddsNetFDLThreshold5(7), ddsNetFDLThreshold10(8), ddsNetFDLThreshold20(9), ddsNetFDLThreshold30(10)

ddsNetFDLAlarm		1.3.6.1.4.1.425.8.4.2.1.21
This status indicates if the Facility Data Link threshold is exceeded.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ddsNetFDLAlarmOther(1), ddsNetFDLAlarmNone(2), ddsNetFDLAlarmThresholdExceeded(3)

ddsNetAlarmResetTimer		1.3.6.1.4.1.425.8.4.2.1.22
Sets the Alarm Reset Timer, this field can be set to any value in the range 0 to 900.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

ddsNetAlarmReset		1.3.6.1.4.1.425.8.4.2.1.23
This is used to clear the current alarm counts.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ddsNetAlarmResetOther(1), ddsNetAlarmResetClearAlarms(2)

serialDteConfigTable		1.3.6.1.4.1.425.8.5.1
The Serial DTE Config Table.
Status: optional	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SerialDteConfigTableEntry

serialDteConfigTableEntry		1.3.6.1.4.1.425.8.5.1.1
An entry in the serial DTE Config Table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SerialDteConfigTableEntry

serialDteConfigNearIndex		1.3.6.1.4.1.425.8.5.1.1.1
Selects the near device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

serialDteConfigFarIndex		1.3.6.1.4.1.425.8.5.1.1.2
Selects the far device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

serialDteConfigIndex		1.3.6.1.4.1.425.8.5.1.1.3
Index into the DteTable.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

serialDteDescription		1.3.6.1.4.1.425.8.5.1.1.4
Contains a textual description of the port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..40)

serialDteType		1.3.6.1.4.1.425.8.5.1.1.5
Selects the DTE port type if applicable.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	serialDteTypeOther(1), serialDteTypeV35(2), serialDteTypeRS232(3), serialDteTypeEIA530(4)

serialDteRate		1.3.6.1.4.1.425.8.5.1.1.6
Selects the DTE port bit.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	serialDteRateOther(1), serialDteRate2400(2), serialDteRate4800(3), serialDteRate9600(4), serialDteRate19200(5), serialDteRate38400(6), serialDteRate52000(7), serialDteRate56000(8), serialDteRate57600(9), serialDteRate60000(10), serialDteRate64000(11), serialDteRate112000(12), serialDteRate128000(13), serialDteRate168000(14), serialDteRate192000(15), serialDteRate224000(16), serialDteRate256000(17), serialDteRate280000(18), serialDteRate320000(19), serialDteRate336000(20), serialDteRate384000(21), serialDteRate392000(22), serialDteRate448000(23), serialDteRate504000(24), serialDteRate512000(25), serialDteRate560000(26), serialDteRate576000(27), serialDteRate616000(28), serialDteRate640000(29), serialDteRate672000(30), serialDteRate704000(31), serialDteRate728000(32), serialDteRate768000(33), serialDteRate784000(34), serialDteRate832000(35), serialDteRate840000(36), serialDteRate896000(37), serialDteRate952000(38), serialDteRate960000(39), serialDteRate1008000(40), serialDteRate1024000(41), serialDteRate1064000(42), serialDteRate1088000(43), serialDteRate1120000(44), serialDteRate1152000(45), serialDteRate1176000(46), serialDteRate1216000(47), serialDteRate1232000(48), serialDteRate1280000(49), serialDteRate1288000(50), serialDteRate1344000(51), serialDteRate1400000(52), serialDteRate1408000(53), serialDteRate1456000(54), serialDteRate1472000(55), serialDteRate1512000(56), serialDteRate1536000(57), serialDteRate1568000(58), serialDteRate1600000(59), serialDteRate1624000(60), serialDteRate1664000(61), serialDteRate1680000(62), serialDteRate1728000(63), serialDteRate1736000(64), serialDteRate1792000(65), serialDteRate1856000(66), serialDteRate1920000(67), serialDteRate1984000(68), serialDteRate2048000(69), serialDteRate1200(70), serialDteRate14400(71), serialDteRate28800(72), serialDteRate48000(73), serialDteRate31200(74), serialDteRate115200(75)

serialDteInvertData		1.3.6.1.4.1.425.8.5.1.1.7
Specifies whether transmit and receive are inverted at the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	serialDteInvertDataOther(1), serialDteInvertDataDisabled(2), serialDteInvertDataEnabled(3)

serialDteFormat		1.3.6.1.4.1.425.8.5.1.1.8
This variable describes the current operations format of the DTE interface. The values mean: serialDteFormatSync The DTE interface is currently set to operate in Syncronous clocking format serialDteFormatAsync The DTE interface is currently set to operate in the Asyncronous clocking format serialDteFormatNotAvail The DTE interface operating format is not available
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	serialDteFormatOther(1), serialDteFormatSync(2), serialDteFormatAsync(3), serialDteFormatNotAvail(4)

serialDteParity		1.3.6.1.4.1.425.8.5.1.1.9
This variable describes the current parity selected for the DTE interface. This variable is only valid when the DTE Mode is set to ASYNC. The values mean: serialDteParityNone The DTE interface is currently set for no parity bit checking or generation serialDteParityOdd The DTE interface is currently set for odd parity serialDteParityEven The DTE interface is currently set for even parity serialDteParityMark The DTE interface is currently set for mark parity serialDteParitySpace The DTE interface is currently set for space parity serialDteParityNotAvail The parity setting on the DTE interface is not available.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	serialDteParityOther(1), serialDteParityNone(2), serialDteParityOdd(3), serialDteParityEven(4), serialDteParityMark(5), serialDteParitySpace(6), serialDteParityNotAvail(7)

serialDteStopBit		1.3.6.1.4.1.425.8.5.1.1.10
This variable describes the stop bit setting for the DTE interface. This variable is only valid when the DTE interface is set to ASYNC. The values mean: serialDteStopBit1 The DTE interface is configured to operate in the ASYNC mode with 1 stop bit serialDteStopBit2 The DTE interface is configured to operate in the ASYNC mode with 2 stop bits serialDteStopBitNotAvail The stop bit information is not available. The DTE interface is probably configured for synchronous operation.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	serialDteStopBitOther(1), serialDteStopBit1(2), serialDteStopBit2(3), serialDteStopBitNotAvail(4)

serialDteMode		1.3.6.1.4.1.425.8.5.1.1.11
This variable describes mode in which data is being sent from the DDS unit back towards the network.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	serialDteModeOther(1), serialDteModeDDSI(2), serialDteModeDDSII(3), serialDteModeTxpINormal(4), serialDteModeTxpITDM(5), serialDteModeTxpIINormal(6), serialDteModeTxpIITDM(7)

serialDteDSR		1.3.6.1.4.1.425.8.5.1.1.12
Selects DSR behavior.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	serialDteDSROther(1), serialDteDSRTestOff(2), serialDteDSRForcedOn(3), serialDteDSRForcedOff(4), serialDteDSRInternal(5)

serialDteDCD		1.3.6.1.4.1.425.8.5.1.1.13
Selects DCD behavior.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	serialDteDCDOther(1), serialDteDCDIdleOff(2), serialDteDCDForcedOn(3), serialDteDCDForcedOff(4), serialDteDCDInternal(5), serialDteDCDFarRTS(6)

serialDteRTS		1.3.6.1.4.1.425.8.5.1.1.14
Selects RTS behavior.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	serialDteRTSOther(1), serialDteRTSNormal(2), serialDteRTSForcedOn(3), serialDteRTSExternal(4)

serialDteRTSDelay		1.3.6.1.4.1.425.8.5.1.1.15
Selects RTS to CTS transition delay.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	serialDteRTSDelayOther(1), serialDteRTSDelayNormal(2), serialDteRTSDelayLong(3)

serialDteDTR		1.3.6.1.4.1.425.8.5.1.1.16
Reports if DTR from the DTE device is false.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	serialDteDTROther(1), serialDteDTRFalse(2), serialDteDTRTrue(3)

serialDteCTS		1.3.6.1.4.1.425.8.5.1.1.17
Specifies the control of the CTS signal at the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	serialDteCTSOther(1), serialDteCTSForceTrue(2), serialDteCTSForceFalse(3), serialDteCTSInternal(4)

serialDteV54		1.3.6.1.4.1.425.8.5.1.1.18
Specifies if the unit should respond to inband V.54 loop commands.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	serialDteV54Other(1), serialDteV54Disable(2), serialDteV54Enable(3)

serialDteLL		1.3.6.1.4.1.425.8.5.1.1.19
Specifies if the unit should respond to local loop activation by the local loopback signal (EIA530 or RS-232 pin 18).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	serialDteLLOther(1), serialDteLLDisable(2), serialDteLLEnable(3)

serialDteRL		1.3.6.1.4.1.425.8.5.1.1.20
Specifies if the unit should respond to remote loop activation by the remote loopback signal (EIA530 or RS-232 pin 21).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	serialDteRLOther(1), serialDteRLDisable(2), serialDteRLEnable(3)

serialDteStartChannel		1.3.6.1.4.1.425.8.5.1.1.21
Specifies the starting channel for the interface.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

serialDteNumberOfChannels		1.3.6.1.4.1.425.8.5.1.1.22
Specifies the number of channels allocated to the interface.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

serialDteTxClock		1.3.6.1.4.1.425.8.5.1.1.23
Specifies how the interface derives its transmit clock.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	serialDteTxClockOther(1), serialDteTxClockInternal(2), serialDteTxClockExternal(3), serialDteTxClockOversample(4)

serialDteBundle		1.3.6.1.4.1.425.8.5.1.1.24
Specifies the allocation pattern of channels assigned to the serial port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), contiguous(2), alternate(3)

serialDteChannelRate		1.3.6.1.4.1.425.8.5.1.1.25
Specifies the rate of all channels assigned to the serial port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), nx56k(2), nx64k(3)

serialDteInvertClock		1.3.6.1.4.1.425.8.5.1.1.26
Specifies if an inverted clock is used to send data from the serial port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), disabled(2), enabled(3)

serialDteAlarmTable		1.3.6.1.4.1.425.8.5.2
The Serial DTE Alarm Table.
Status: optional	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SerialDteAlarmTableEntry

serialDteAlarmTableEntry		1.3.6.1.4.1.425.8.5.2.1
An entry in the serial DTE Alarm Table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SerialDteAlarmTableEntry

serialDteAlarmNearIndex		1.3.6.1.4.1.425.8.5.2.1.1
Selects the near device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

serialDteAlarmFarIndex		1.3.6.1.4.1.425.8.5.2.1.2
Selects the far device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

serialDteAlarmIndex		1.3.6.1.4.1.425.8.5.2.1.3
Index into the serialDteAlarmTable.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

serialDteDTRAlarmControl		1.3.6.1.4.1.425.8.5.2.1.4
Specifies if the unit should alarm on loss of DTR.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	serialDteDTRAlarmOther(1), serialDteDTRAlarmDisable(2), serialDteDTRAlarmEnable(3)

serialDteDTRAlarmStatus		1.3.6.1.4.1.425.8.5.2.1.5
This status indicates a DTR Loss alarm is active.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	serialDteDTRAlarmOther(1), serialDteDTRAlarmNone(2), serialDteDTRAlarmActive(3)

serialDteStatusSummary		1.3.6.1.4.1.425.8.5.2.1.6
This object provides a summary of the port status.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

serialDteAlarmSummary		1.3.6.1.4.1.425.8.5.2.1.7
This object provides a summary of the port alarms.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

serialDteASCStatus		1.3.6.1.4.1.425.8.5.2.1.8
Reports if an ASC condition exists on the interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	serialDteStatusASCOther(1), serialDteStatusNoASC(2), serialDteStatusASC(3)

serialDteASCCount		1.3.6.1.4.1.425.8.5.2.1.9
This count contains the number of ASC seconds received by the interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

serialDteASCThreshold		1.3.6.1.4.1.425.8.5.2.1.10
The number of ASC seconds that must be received before an alarm is declared.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

serialDteASCAlarm		1.3.6.1.4.1.425.8.5.2.1.11
This status indicates if the ASC Seconds threshold is exceeded.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	serialDteASCAlarmOther(1), serialDteASCAlarmNone(2), serialDteASCAlarmThresholdExceeded(3)

serialDteFDLStatus		1.3.6.1.4.1.425.8.5.2.1.12
Reports if an FDL error condition exists on the interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	serialDteStatusFDLOther(1), serialDteStatusNoFDL(2), serialDteStatusFDL(3)

serialDteFDLCount		1.3.6.1.4.1.425.8.5.2.1.13
This count contains the number of FDL errored seconds received by the interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

serialDteFDLThreshold		1.3.6.1.4.1.425.8.5.2.1.14
The number of FDL errored seconds that must be received before an alarm is declared.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

serialDteFDLAlarm		1.3.6.1.4.1.425.8.5.2.1.15
This status indicates if the FDL Errored Seconds threshold is exceeded.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	serialDteFDLAlarmOther(1), serialDteFDLAlarmNone(2), serialDteFDLAlarmThresholdExceeded(3)

serialDteLOSStatus		1.3.6.1.4.1.425.8.5.2.1.16
Reports if an LOS condition exists on the interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	serialDteStatusLOSOther(1), serialDteStatusNoLOS(2), serialDteStatusLOS(3)

serialDteLOSCount		1.3.6.1.4.1.425.8.5.2.1.17
This count contains the number of LOS seconds received by the interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

serialDteLOSThreshold		1.3.6.1.4.1.425.8.5.2.1.18
The number of LOS seconds that must be received before an alarm is declared.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

serialDteLOSAlarm		1.3.6.1.4.1.425.8.5.2.1.19
This status indicates if the LOS Seconds threshold is exceeded.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	serialDteLOSAlarmOther(1), serialDteLOSAlarmNone(2), serialDteLOSAlarmThresholdExceeded(3)

analogDteTable		1.3.6.1.4.1.425.8.6.1
The Analog DTE Table.
Status: optional	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AnalogDteTableEntry

analogDteTableEntry		1.3.6.1.4.1.425.8.6.1.1
An entry in the Analog DTE Table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	AnalogDteTableEntry

analogDteNearIndex		1.3.6.1.4.1.425.8.6.1.1.1
Selects the near device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

analogDteFarIndex		1.3.6.1.4.1.425.8.6.1.1.2
Selects the far device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

analogDteIndex		1.3.6.1.4.1.425.8.6.1.1.3
Index into the analogDteTable.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

analogDteDescription		1.3.6.1.4.1.425.8.6.1.1.4
Contains a textual description of the port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..40)

analogDteCardType		1.3.6.1.4.1.425.8.6.1.1.5
Identifies the analog DTE card type.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	analogDteCardTypeOther(1), analogDteCardTypeFXS(2), analogDteCardTypeFXO(3), analogDteCardType4WEM(4)

analogDteMode		1.3.6.1.4.1.425.8.6.1.1.6
Selects whether the port is actively assigned to a netowrk channel or not used.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	analogDteModeOther(1), analogDteModeSpare(2), analogDteModeActive(3)

analogDteState		1.3.6.1.4.1.425.8.6.1.1.7
Displays the port status as either in the Busy or Idle state.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	analogDteStateOther(1), analogDteStateIdle(2), analogDteStateBusy(3)

analogDteElementID		1.3.6.1.4.1.425.8.6.1.1.8
This object signifies the name of the device.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

analogDteSignalling		1.3.6.1.4.1.425.8.6.1.1.9
Selects the supervisory operation of the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	analogDteSignallingOther(1), analogDteSignallingFXSLS(2), analogDteSignallingFXSGS(3), analogDteSignallingUVG(4), analogDteSignallingMEGLS(5), analogDteSignallingMEGGS(6), analogDteSignallingMEGRLS(7), analogDteSignallingMEGRGS(8), analogDteSignallingPLAR(9), analogDteSignallingSLC96(10), analogDteSignallingDIDDNIS(11), analogDteSignallingDNISWLS(12), analogDteSignallingDNISDLS(13), analogDteSignallingDNISWRLS(14), analogDteSignallingDNISDRLS(15), analogDteSignallingDNISWGS(16), analogDteSignallingDNISDGS(17), analogDteSignallingDNISWRGS(18), analogDteSignallingDNISDRGS(19), analogDteSignallingFXOLS(20), analogDteSignallingFXOGS(21), analogDteSignallingFXOUVG(22), analogDteSignallingFXOUVGR(23), analogDteSignalling4WEMTYPE1(24), analogDteSignalling4WEMTYPE2(25), analogDteSignalling4WEMTYPE3(26), analogDteSignalling4WEMTYPE4(27), analogDteSignalling4WEMTYPE5(28), analogDteSignalling4WEMTO(29)

analogDteDNISDelay		1.3.6.1.4.1.425.8.6.1.1.10
If the signalling mode has a delay, it can be set from 1 to 5 seconds.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	analogDteDNISDelayOther(1), analogDteDNISDelay1Second(2), analogDteDNISDelay2Seconds(3), analogDteDNISDelay3Seconds(4), analogDteDNISDelay4Seconds(5), analogDteDNISDelay5Seconds(6)

analogDteTxGain		1.3.6.1.4.1.425.8.6.1.1.11
Selects the transmit gain. Values prefixed with m are negative.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	analogDteTxGainOther(1), analogDteTxGain3DB(2), analogDteTxGain2DB(3), analogDteTxGain1DB(4), analogDteTxGain0DB(5), analogDteTxGainm1DB(6), analogDteTxGainm2DB(7), analogDteTxGainm3DB(8), analogDteTxGainm4DB(9), analogDteTxGainm5DB(10), analogDteTxGainm6DB(11), analogDteTxGainm7DB(12), analogDteTxGainm8DB(13), analogDteTxGainm9DB(14), analogDteTxGainm10DB(15)

analogDteRxGain		1.3.6.1.4.1.425.8.6.1.1.12
Selects the receive gain. Values prefixed with m are negative.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	analogDteRxGainOther(1), analogDteRxGain2DB(2), analogDteRxGain1DB(3), analogDteRxGain0DB(4), analogDteRxGainm1DB(5), analogDteRxGainm2DB(6), analogDteRxGainm3DB(7), analogDteRxGainm4DB(8), analogDteRxGainm5DB(9), analogDteRxGainm6DB(10), analogDteRxGainm7DB(11), analogDteRxGainm8DB(12), analogDteRxGainm9DB(13), analogDteRxGainm10DB(14), analogDteRxGainm11DB(15), analogDteRxGainm12DB(16), analogDteRxGainm13DB(17), analogDteRxGainm14DB(18), analogDteRxGainm15DB(19), analogDteRxGainm16DB(20)

connectionTable		1.3.6.1.4.1.425.8.7.1
The connection table.
Status: optional	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ConnectionTableEntry

connectionTableEntry		1.3.6.1.4.1.425.8.7.1.1
An entry in the connection table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	ConnectionTableEntry

connectionNearIndex		1.3.6.1.4.1.425.8.7.1.1.1
Selects the near device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

connectionFarIndex		1.3.6.1.4.1.425.8.7.1.1.2
Selects the far device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

connectionTableIndex		1.3.6.1.4.1.425.8.7.1.1.3
The index into the connection table.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

connectionTableDescription		1.3.6.1.4.1.425.8.7.1.1.4
A description of the connection.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..60)

connectionChannelTable		1.3.6.1.4.1.425.8.7.2
The channel-level connection table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ConnectionChannelEntry

connectionChannelEntry		1.3.6.1.4.1.425.8.7.2.1
An entry in the connectionChannelTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	ConnectionChannelEntry

connectionChannelNearIndex		1.3.6.1.4.1.425.8.7.2.1.1
Selects the near device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

connectionChannelFarIndex		1.3.6.1.4.1.425.8.7.2.1.2
Selects the far device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

connectionChannelLineIndex		1.3.6.1.4.1.425.8.7.2.1.3
Selects instance of line.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

connectionChannelIndex		1.3.6.1.4.1.425.8.7.2.1.4
The index into the connection table.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

channelInterfaceAssignment		1.3.6.1.4.1.425.8.7.2.1.5
The channel assignment.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), unassigned(2), dTE(3), remComm(4), port1(5), port2(6), port3(7), port4(8), port5(9), port6(10), port7(11), port8(12), port9(13), port10(14), port11(15), port12(16), port13(17), port14(18), port15(19), port16(20), port17(21), port18(22), port19(23), port20(24), port21(25), port22(26), port23(27), port24(28), port25(29), port26(30), port27(31), port28(32), port29(33), port30(34), port31(35), port32(36), slot2PortA(37), slot2PortB(38), slot3PortA(39), slot3PortB(40), slot4PortA(41), slot4PortB(42), slot5PortA(43), slot5PortB(44), slot6PortA(45), slot6PortB(46), slot2Dsu1PortA(47), slot2Dsu1PortB(48), slot2Dsu2PortA(49), slot2Dsu2PortB(50), slot2Dsu3PortA(51), slot2Dsu3PortB(52), slot2Dsu4PortA(53), slot2Dsu4PortB(54), slot2Dsu5PortA(55), slot2Dsu5PortB(56), slot2Dsu6PortA(57), slot2Dsu6PortB(58), slot3Dsu1PortA(59), slot3Dsu1PortB(60), slot3Dsu2PortA(61), slot3Dsu2PortB(62), slot3Dsu3PortA(63), slot3Dsu3PortB(64), slot3Dsu4PortA(65), slot3Dsu4PortB(66), slot3Dsu5PortA(67), slot3Dsu5PortB(68), slot3Dsu6PortA(69), slot3Dsu6PortB(70), slot4Dsu1PortA(71), slot4Dsu1PortB(72), slot4Dsu2PortA(73), slot4Dsu2PortB(74), slot4Dsu3PortA(75), slot4Dsu3PortB(76), slot4Dsu4PortA(77), slot4Dsu4PortB(78), slot4Dsu5PortA(79), slot4Dsu5PortB(80), slot4Dsu6PortA(81), slot4Dsu6PortB(82), slot5Dsu1PortA(83), slot5Dsu1PortB(84), slot5Dsu2PortA(85), slot5Dsu2PortB(86), slot5Dsu3PortA(87), slot5Dsu3PortB(88), slot5Dsu4PortA(89), slot5Dsu4PortB(90), slot5Dsu5PortA(91), slot5Dsu5PortB(92), slot5Dsu6PortA(93), slot5Dsu6PortB(94), slot6Dsu1PortA(95), slot6Dsu1PortB(96), slot6Dsu2PortA(97), slot6Dsu2PortB(98), slot6Dsu3PortA(99), slot6Dsu3PortB(100), slot6Dsu4PortA(101), slot6Dsu4PortB(102), slot6Dsu5PortA(103), slot6Dsu5PortB(104), slot6Dsu6PortA(105), slot6Dsu6PortB(106)

channelInterfaceDescription		1.3.6.1.4.1.425.8.7.2.1.6
Contains a description of the interface channel connection.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..40)

channelInterfaceChannel		1.3.6.1.4.1.425.8.7.2.1.7
Displays the corresponding channel of the interface channel connection.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

channelSignalling		1.3.6.1.4.1.425.8.7.2.1.8
Allows a selection of Clear Channel or Robbed Bit signalling for each DS0.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), clearChannel(2), robbedBit(3)

bertTable		1.3.6.1.4.1.425.8.8.1
BERT control table.
Status: optional	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		BertTableEntry

bertTableEntry		1.3.6.1.4.1.425.8.8.1.1
An entry in the BERT control table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	BertTableEntry

bertNearIndex		1.3.6.1.4.1.425.8.8.1.1.1
Selects the near device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

bertFarIndex		1.3.6.1.4.1.425.8.8.1.1.2
Selects the far device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

bertIndex		1.3.6.1.4.1.425.8.8.1.1.3
The index into the BERT control table. Selects which BERT chip to use.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

bertPattern		1.3.6.1.4.1.425.8.8.1.1.4
Selects the test pattern to be used.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	bertPatternOther(1), bertPatternQRSS(2), bertPattern63(3), bertPattern511(4), bertPattern2047(5), bertPattern215(6), bertPattern220(7), bertPattern223(8), bertPattern1in8(9), bertPattern3in24(10), bertPatternALT(11), bertPatternCLEAR(12)

bertLength		1.3.6.1.4.1.425.8.8.1.1.5
Specifies how long the test should run.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	bertLengthOther(1), bertLength15minutes(2), bertLength30minutes(3), bertLength60minutes(4), bertLength24hours(5), bertLengthContinuous(6)

bertPatternSync		1.3.6.1.4.1.425.8.8.1.1.6
Displays the current state of pattern sync during a test.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	bertPatternSyncOther(1), bertPatternSyncNoTest(2), bertPatternSyncNoSync(3), bertPatternSyncInsync(4)

bertElapsedTime		1.3.6.1.4.1.425.8.8.1.1.7
Displays the amount of time elapsed since a timed test began in seconds.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

bertBitErrors		1.3.6.1.4.1.425.8.8.1.1.8
Displays the total number of bit errors detected since the test began.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

bertErroredSeconds		1.3.6.1.4.1.425.8.8.1.1.9
Displays the number of asynchronous errored seconds that have been detected since the test began.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

bertPercentEFS		1.3.6.1.4.1.425.8.8.1.1.10
Displays a ratio derived from the number of error free seconds divided by the number of seconds accumulated in elapsed time.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

bertCommand		1.3.6.1.4.1.425.8.8.1.1.11
Issues a test command for the interface.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	bertCommandOther(1), bertCommandStart(2), bertCommandStop(3), bertCommandResetErrors(4), bertCommandInjectError(5)

bertInterfaceTable		1.3.6.1.4.1.425.8.8.2
BERT control interface table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		BertInterfaceTableEntry

bertInterfaceTableEntry		1.3.6.1.4.1.425.8.8.2.1
An entry in the BERT control interface table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	BertInterfaceTableEntry

bertInterfaceNearIndex		1.3.6.1.4.1.425.8.8.2.1.1
Selects the near device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

bertInterfaceFarIndex		1.3.6.1.4.1.425.8.8.2.1.2
Selects the far device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

bertChipIndex		1.3.6.1.4.1.425.8.8.2.1.3
Selects which BERT chip to use.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

bertInterfaceIndex		1.3.6.1.4.1.425.8.8.2.1.4
An index into the MIB-II interfaces table; the interface for the BERT settings.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

bertInterfaceSetting		1.3.6.1.4.1.425.8.8.2.1.5
Specifies the interface for the BERT chip.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	bertInterfaceSettingOther(1), bertInterfaceSettingIdle(2), bertInterfaceSettingChannel1(3), bertInterfaceSettingChannel2(4), bertInterfaceSettingChannel3(5), bertInterfaceSettingChannel4(6), bertInterfaceSettingChannel5(7), bertInterfaceSettingChannel6(8), bertInterfaceSettingChannel7(9), bertInterfaceSettingChannel8(10), bertInterfaceSettingChannel9(11), bertInterfaceSettingChannel10(12), bertInterfaceSettingChannel11(13), bertInterfaceSettingChannel12(14), bertInterfaceSettingChannel13(15), bertInterfaceSettingChannel14(16), bertInterfaceSettingChannel15(17), bertInterfaceSettingChannel16(18), bertInterfaceSettingChannel17(19), bertInterfaceSettingChannel18(20), bertInterfaceSettingChannel19(21), bertInterfaceSettingChannel20(22), bertInterfaceSettingChannel21(23), bertInterfaceSettingChannel22(24), bertInterfaceSettingChannel23(25), bertInterfaceSettingChannel24(26), bertInterfaceSettingChannel25(27), bertInterfaceSettingChannel26(28), bertInterfaceSettingChannel27(29), bertInterfaceSettingChannel28(30), bertInterfaceSettingChannel29(31), bertInterfaceSettingChannel30(32), bertInterfaceSettingChannel31(33), bertInterfaceSettingChannel32(34), bertInterfaceSettingNet(35), bertInterfaceSettingDTE(36), bertInterfaceSettingNotEnabled(37)

testTable		1.3.6.1.4.1.425.8.8.3
Test control table.
Status: optional	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TestTableEntry

testTableEntry		1.3.6.1.4.1.425.8.8.3.1
An entry in the testTable.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	TestTableEntry

testNearIndex		1.3.6.1.4.1.425.8.8.3.1.1
Selects the near device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

testFarIndex		1.3.6.1.4.1.425.8.8.3.1.2
Selects the far device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

testTableIndex		1.3.6.1.4.1.425.8.8.3.1.3
The index into the testTable, one entry for each interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

testType		1.3.6.1.4.1.425.8.8.3.1.4
Identifies the test type for the interface.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	testTypeOther(1), testTypeNoTest(2), testTypePLB(3), testTypeLLB(4), testtypeMLB(5), testTypeFarPLB(6), testTypeFarLLB(7), testTypeFarMLB(8), testTypePortLoop(9), testTypeV54Loop(10), testTypeFarV54Loop(11)

testLoopDirection		1.3.6.1.4.1.425.8.8.3.1.5
This object is the identifier of the current unit loop mode. The values mean: testLoopUnidirectional Line, Data, and V54 loops will be unidirectional Local loop will be bidirectional testLoopBidirectional All loops will be bidirectional
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	testLoopOther(1), testLoopUnidirectional(2), testLoopBidirectional(3)

testFarLLBFraming		1.3.6.1.4.1.425.8.8.3.1.6
This setting, for Far LLB tests on T1 lines, must match the far end unit loop code framing.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	testFarLLBFramingOther(1), testFarLLBFramingUnframed(2), testFarLLBFramingFramed(3)

performance24Table		1.3.6.1.4.1.425.8.9.1
Performance table, contains TR54016 standard and enhanced data.
Status: optional	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Performance24TableEntry

performance24TableEntry		1.3.6.1.4.1.425.8.9.1.1
An entry in the performance24Table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	Performance24TableEntry

performance24NearIndex		1.3.6.1.4.1.425.8.9.1.1.1
Selects the near device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

performance24FarIndex		1.3.6.1.4.1.425.8.9.1.1.2
Selects the far device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

performance24InterfaceIndex		1.3.6.1.4.1.425.8.9.1.1.3
Selects the interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

performance24Index		1.3.6.1.4.1.425.8.9.1.1.4
The index into the 24-hour performance table.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	performance24Summary(1), performance24Current(2), performance24period1(3), performance24period2(4), performance24period3(5), performance24period4(6), performance24period5(7), performance24period6(8), performance24period7(9), performance24period8(10), performance24period9(11), performance24period10(12), performance24period11(13), performance24period12(14), performance24period13(15), performance24period14(16), performance24period15(17), performance24period16(18), performance24period17(19), performance24period18(20), performance24period19(21), performance24period20(22), performance24period21(23), performance24period22(24), performance24period23(25), performance24period24(26), performance24period25(27), performance24period26(28), performance24period27(29), performance24period28(30), performance24period29(31), performance24period30(32), performance24period31(33), performance24period32(34), performance24period33(35), performance24period34(36), performance24period35(37), performance24period36(38), performance24period37(39), performance24period38(40), performance24period39(41), performance24period40(42), performance24period41(43), performance24period42(44), performance24period43(45), performance24period44(46), performance24period45(47), performance24period46(48), performance24period47(49), performance24period48(50), performance24period49(51), performance24period50(52), performance24period51(53), performance24period52(54), performance24period53(55), performance24period54(56), performance24period55(57), performance24period56(58), performance24period57(59), performance24period58(60), performance24period59(61), performance24period60(62), performance24period61(63), performance24period62(64), performance24period63(65), performance24period64(66), performance24period65(67), performance24period66(68), performance24period67(69), performance24period68(70), performance24period69(71), performance24period70(72), performance24period71(73), performance24period72(74), performance24period73(75), performance24period74(76), performance24period75(77), performance24period76(78), performance24period77(79), performance24period78(80), performance24period79(81), performance24period80(82), performance24period81(83), performance24period82(84), performance24period83(85), performance24period84(86), performance24period85(87), performance24period86(88), performance24period87(89), performance24period88(90), performance24period89(91), performance24period90(92), performance24period91(93), performance24period92(94), performance24period93(95), performance24period94(96), performance24period95(97), performance24period96(98)

performance24ES		1.3.6.1.4.1.425.8.9.1.1.5
The number of Errored Seconds for the 15-minute period.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

performance24BES		1.3.6.1.4.1.425.8.9.1.1.6
The number of Bursty Errored Seconds for the 15-minute period.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

performance24SES		1.3.6.1.4.1.425.8.9.1.1.7
The number of Severely Errored Seconds for the 15-minute period.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

performance24UAS		1.3.6.1.4.1.425.8.9.1.1.8
The number of Unavailable Seconds for the 15-minute period.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

performance24LOFC		1.3.6.1.4.1.425.8.9.1.1.9
The number of Loss of Frame Counts for the 15-minute period.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

performance24CSS		1.3.6.1.4.1.425.8.9.1.1.10
The number of Controlled Slip Seconds for the 15-minute period.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

performance24CRCES		1.3.6.1.4.1.425.8.9.1.1.11
The number of CRC Errored Seconds for the 15-minute period.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

performance24OOFS		1.3.6.1.4.1.425.8.9.1.1.12
The number of Out of Frame Seconds for the 15-minute period.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

performance24LOSS		1.3.6.1.4.1.425.8.9.1.1.13
The number of Loss of Signal Seconds for the 15-minute period.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

performance24AISS		1.3.6.1.4.1.425.8.9.1.1.14
The number of Alarm Indication Signal Seconds for the 15-minute period.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

performance24RAS		1.3.6.1.4.1.425.8.9.1.1.15
The number of Remote Alarm (Yellow) Seconds for the 15-minute period.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

performance24BPVS		1.3.6.1.4.1.425.8.9.1.1.16
The number of Bipolar Violation Seconds for the 15-minute period.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

performance30Table		1.3.6.1.4.1.425.8.9.2
Performance table, contains TR54016 standard and enhanced 30-day data.
Status: optional	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Performance30TableEntry

performance30TableEntry		1.3.6.1.4.1.425.8.9.2.1
An entry in the performance30Table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	Performance30TableEntry

performance30NearIndex		1.3.6.1.4.1.425.8.9.2.1.1
Selects the near device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

performance30FarIndex		1.3.6.1.4.1.425.8.9.2.1.2
Selects the far device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

performance30InterfaceIndex		1.3.6.1.4.1.425.8.9.2.1.3
Selects the interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

performance30Index		1.3.6.1.4.1.425.8.9.2.1.4
The index into the 30-day performance table.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	performance30Summary(1), performance30day1(2), performance30day2(3), performance30day3(4), performance30day4(5), performance30day5(6), performance30day6(7), performance30day7(8), performance30day8(9), performance30day9(10), performance30day10(11), performance30day11(12), performance30day12(13), performance30day13(14), performance30day14(15), performance30day15(16), performance30day16(17), performance30day17(18), performance30day18(19), performance30day19(20), performance30day20(21), performance30day21(22), performance30day22(23), performance30day23(24), performance30day24(25), performance30day25(26), performance30day26(27), performance30day27(28), performance30day28(29), performance30day29(30), performance30day30(31)

performance30ES		1.3.6.1.4.1.425.8.9.2.1.5
The number of Errored Seconds for the 1-day period.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

performance30BES		1.3.6.1.4.1.425.8.9.2.1.6
The number of Bursty Errored Seconds for the 1-day period.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

performance30SES		1.3.6.1.4.1.425.8.9.2.1.7
The number of Severely Errored Seconds for the 1-day period.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

performance30UAS		1.3.6.1.4.1.425.8.9.2.1.8
The number of Unavailable Seconds for the 1-day period.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

performance30LOFC		1.3.6.1.4.1.425.8.9.2.1.9
The number of Loss of Frame Counts for the 1-day period.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

performance30CSS		1.3.6.1.4.1.425.8.9.2.1.10
The number of Controlled Slip Seconds for the 1-day period.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

performance30CRCES		1.3.6.1.4.1.425.8.9.2.1.11
The number of CRC Errored Seconds for the 1-day period.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

performance30OOFS		1.3.6.1.4.1.425.8.9.2.1.12
The number of Out of Frame Seconds for the 1-day period.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

performance30LOSS		1.3.6.1.4.1.425.8.9.2.1.13
The number of Loss of Signal Seconds for the 1-day period.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

performance30AISS		1.3.6.1.4.1.425.8.9.2.1.14
The number of Alarm Indication Signal Seconds for the 1-day period.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

performance30RAS		1.3.6.1.4.1.425.8.9.2.1.15
The number of Remote Alarm (Yellow) Seconds for the 1-day period.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

performance30BPVS		1.3.6.1.4.1.425.8.9.2.1.16
The number of Bipolar Violation Seconds for the 1-day period.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

iTable		1.3.6.1.4.1.425.8.10.1
The interface table.
Status: optional	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ITableEntry

iTableEntry		1.3.6.1.4.1.425.8.10.1.1
An entry in the interface table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	ITableEntry

iTableNearIndex		1.3.6.1.4.1.425.8.10.1.1.1
Selects the near device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

iTableFarIndex		1.3.6.1.4.1.425.8.10.1.1.2
Selects the far device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

iTableIndex		1.3.6.1.4.1.425.8.10.1.1.3
The index into the interface table, used for addressing in above tables.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

iDescription		1.3.6.1.4.1.425.8.10.1.1.4
Description of the interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..80)

iType		1.3.6.1.4.1.425.8.10.1.1.5
Enumerated interface type.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(0), v35(1), eia530(2), rs232(3), voice(4), hsdata(5), dualt1dte(6), dualddsv1(7), hexdds(8), ocudp(9), x21(10), dualddsv2(11), rfdl(128), alt(129), t1dte(130), didte(131), t1ntw(132), e1ntw(133), ddsntw(134), ddsdte(135), ddsdbu(136), fxs(137), fxo(138), eandm(139), e1sig(192)

iSlot		1.3.6.1.4.1.425.8.10.1.1.6
Device-dependent slot in which the interface resides.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

iPort		1.3.6.1.4.1.425.8.10.1.1.7
Device-dependent port in which the interface resides.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

iStatus		1.3.6.1.4.1.425.8.10.1.1.8
Status of the interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	iStatusOther(1), iStatusOK(2), iStatusErrored(3), iStatusAlarmed(4), iStatusTesting(5)

traplogTable		1.3.6.1.4.1.425.8.11.1
The traplog table.
Status: optional	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TraplogEntry

traplogEntry		1.3.6.1.4.1.425.8.11.1.1
An entry in the traplog table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	TraplogEntry

traplogIndex		1.3.6.1.4.1.425.8.11.1.1.1
The index into the traplog table.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

traplogNearIndex		1.3.6.1.4.1.425.8.11.1.1.2
Specifies the near device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

traplogFarIndex		1.3.6.1.4.1.425.8.11.1.1.3
Specifies the far device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

traplogInterfaceIndex		1.3.6.1.4.1.425.8.11.1.1.4
Specifies the interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

traplogTrapNum		1.3.6.1.4.1.425.8.11.1.1.5
The SNMP trap id.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

traplogTimeStamp		1.3.6.1.4.1.425.8.11.1.1.6
Time the SNMP was generated.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..40)

traplogDeviceType		1.3.6.1.4.1.425.8.11.1.1.7
Specifies the device type for the trap.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), none(2), t12000(3), e12048(4), e13021(5), t13000(6), t13001(7), t13002(8), t13030(9), t13060(10), t13101(11), t13102(12), t13111(13), t13112(14), dds4001(15), dds4101(16), dds4051(17), dds4151(18), dds41TDM(19), generic54016(20)

traplogDeleteEntry		1.3.6.1.4.1.425.8.11.2
Writing the index of a trap to this object will delete the trap entry. Writing an index value of 0 will delete all entries.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

traplogSortOption		1.3.6.1.4.1.425.8.11.3
Determines the order in which traps are presented.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), ascendingtimestamp(2), ascendingunit(3)

traplogLastTimeStamp		1.3.6.1.4.1.425.8.11.4
The timestamp of the newest trap in the trap log.
Status: mandatory	Access: read-only
OBJECT-TYPE
	TimeTicks

unitUtilitiesTable		1.3.6.1.4.1.425.8.12.1
The unit utilities table.
Status: optional	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		UnitUtilitiesTableEntry

unitUtilitiesTableEntry		1.3.6.1.4.1.425.8.12.1.1
An entry in the unit utilities table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	UnitUtilitiesTableEntry

unitUtilitiesNearIndex		1.3.6.1.4.1.425.8.12.1.1.1
Selects the near device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

unitUtilitiesFarIndex		1.3.6.1.4.1.425.8.12.1.1.2
Selects the far device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

unitUtilitiesLocalPassword		1.3.6.1.4.1.425.8.12.1.1.3
The password for local access to a device (VT100, front panel).
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

unitUtilitiesTime		1.3.6.1.4.1.425.8.12.1.1.4
This string is the current time as known to the device. The current time may be entered in this field using the HHMMSS format. For example, 3:45AM is entered as 034500 and 3:45PM is entered as 154500.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..6)

unitUtilitiesDate		1.3.6.1.4.1.425.8.12.1.1.5
This string is the current date as known to the device. The current date may be entered in this field using the MMDDYY format. For example, July 4, 1997 is entered as 070497.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..6)

unitUtilitiesMaintenanceReset		1.3.6.1.4.1.425.8.12.1.1.6
This field allows resetting the device to default values by reloading the start-up default configuration parameters.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), reset(2), restart(3)

unitUtilitiesAlarmResetTimer		1.3.6.1.4.1.425.8.12.1.1.7
This field allows setting a timer which will cause all existing alarms on the device to be cleared upon expiration. The counter is in seconds.
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER

unitUtilitiesAlarmClear		1.3.6.1.4.1.425.8.12.1.1.8
Writing a 2 to this field causes all existing alarms to be cleared immediatedly.
Status: optional	Access: read-write
OBJECT-TYPE
	INTEGER	utilitiesAlarmClearOther(1), utilitiesAlarmClearNow(2)