INTEL-GEN-MIB

Imported modules

RFC1155-SMI	RFC-1212	RFC1213-MIB
RFC-1215

Imported symbols

enterprises	IpAddress	TimeTicks
OBJECT-TYPE	DisplayString	TRAP-TYPE

Defined Types

SysConfEntry
SEQUENCE
	confStatus	INTEGER
	confName	OCTET STRING	Size(0..256)
	confTime	INTEGER
	confTftpIp	IpAddress

SysLogEntry
SEQUENCE
	logType	INTEGER
	logEntries	INTEGER
	logFileName	DisplayString	Size(128)
	logLastChanged	TimeTicks

IpConfEntry
SEQUENCE
	ipAddressAssignment	INTEGER
	ipAddress	IpAddress
	ipSubNetMask	IpAddress
	ipRouterAddress	IpAddress
	ipBroadcastAddress	IpAddress
	ipBootpServerAddress	IpAddress

IpModuleConfEntry
SEQUENCE
	ipModuleChassisIndex	INTEGER
	ipModuleModuleIndex	INTEGER
	ipModuleConfigIndex	INTEGER
	ipModuleAddressAssignment	INTEGER
	ipModuleAddress	IpAddress
	ipModuleSubNetMask	IpAddress
	ipModuleRouterAddress	IpAddress
	ipModuleBroadcastAddress	IpAddress
	ipModuleBootpServerAddress	IpAddress

SnmpAuthEntry
SEQUENCE
	authNumber	INTEGER
	authProtocolAccessIpCommunity	OCTET STRING	Size(10..41)
	authDelete	INTEGER

SnmpTrapEntry
SEQUENCE
	trapNumber	INTEGER
	trapIpAndGroupAndCommunity	OCTET STRING	Size(8..39)
	trapDelete	INTEGER

SnmpAccessEntry
SEQUENCE
	snmpAccessIP	IpAddress
	snmpAccessTime	INTEGER
	snmpAccessProtocol	INTEGER
	snmpAccessType	INTEGER

ChassisEntry
SEQUENCE
	chassisIndex	INTEGER
	chassisType	INTEGER
	chassisMaxModules	INTEGER
	chassisModules	INTEGER
	chassisUserAssignedType	DisplayString	Size(0..24)
	chassisUserAssignedNumber	DisplayString	Size(0..24)
	chassisUserAssignedName	DisplayString	Size(0..24)
	chassisMaxPSUs	INTEGER

ModuleEntry
SEQUENCE
	moduleChassisIndex	INTEGER
	moduleIndex	INTEGER
	moduleType	INTEGER
	moduleFirstPort	INTEGER
	moduleNumberOfPorts	INTEGER
	moduleMaxMediaModules	INTEGER
	moduleUserAssignedType	DisplayString	Size(0..24)
	moduleUserAssignedNumber	DisplayString	Size(0..24)
	moduleUserAssignedName	DisplayString	Size(0..24)
	moduleRAM	INTEGER
	moduleEPROM	INTEGER
	moduleFLASHPROM	INTEGER
	moduleLEDInfo	OCTET STRING	Size(2..32)
	moduleAllPortType	OCTET STRING
	moduleAllPortLEDInfo	OCTET STRING
	moduleAllPortStatus	OCTET STRING
	moduleLastPortChange	TimeTicks
	moduleMacAddress	OCTET STRING	Size(6)
	moduleIpAddress	IpAddress
	moduleSerialNumber	DisplayString	Size(0..32)
	moduleVersion	INTEGER
	moduleSwStatus	INTEGER
	moduleSwName	OCTET STRING
	moduleSwDescription	DisplayString
	moduleSwLoadTime	INTEGER
	moduleSwTftpIp	IpAddress
	moduleBackupSwStatus	INTEGER
	moduleBackupSwName	OCTET STRING
	moduleBackupSwDescription	DisplayString
	moduleBackupSwLoadTime	INTEGER
	moduleBackupSwTftpIp	IpAddress
	moduleSwTftpIpAndSwName	OCTET STRING	Size(4..260)
	moduleSwUpdateResult	INTEGER
	moduleSpecificObject	OCTET STRING	Size(0..256)
	moduleTemperatureStatus	INTEGER
	moduleBootSectionVersion	INTEGER

MediaModuleEntry
SEQUENCE
	mediaModuleChassisIndex	INTEGER
	mediaModuleModuleIndex	INTEGER
	mediaModuleIndex	INTEGER
	mediaModuleType	INTEGER
	mediaModuleFirstPort	INTEGER
	mediaModuleNumberOfPorts	INTEGER
	mediaModuleVersion	INTEGER

PortEntry
SEQUENCE
	portChassisIndex	INTEGER
	portModuleIndex	INTEGER
	portIndex	INTEGER
	portMediaModuleIndex	INTEGER
	portIfIndex	INTEGER
	portType	INTEGER
	portStatus	INTEGER
	portLEDInfo	OCTET STRING
	portTimeSinceLastStateChange	TimeTicks
	portResetAllCounters	INTEGER
	portReset	INTEGER
	portLastErrorID	INTEGER
	portUserAssignedName	DisplayString	Size(0..32)

Defined Values

intel		1.3.6.1.4.1.343
OBJECT IDENTIFIER

sysProducts		1.3.6.1.4.1.343.5
OBJECT IDENTIFIER

switches		1.3.6.1.4.1.343.5.1
OBJECT IDENTIFIER

express10		1.3.6.1.4.1.343.5.1.1
OBJECT IDENTIFIER

express10plus		1.3.6.1.4.1.343.5.1.2
OBJECT IDENTIFIER

express100fx		1.3.6.1.4.1.343.5.1.3
OBJECT IDENTIFIER

express550t		1.3.6.1.4.1.343.5.1.4
OBJECT IDENTIFIER

express550f		1.3.6.1.4.1.343.5.1.5
OBJECT IDENTIFIER

express510t		1.3.6.1.4.1.343.5.1.6
OBJECT IDENTIFIER

express520t		1.3.6.1.4.1.343.5.1.7
OBJECT IDENTIFIER

expressGigaSwitch		1.3.6.1.4.1.343.5.1.8
OBJECT IDENTIFIER

express460t-16		1.3.6.1.4.1.343.5.1.9
OBJECT IDENTIFIER

express460t-24		1.3.6.1.4.1.343.5.1.10
OBJECT IDENTIFIER

nstructure560t		1.3.6.1.4.1.343.5.1.11
OBJECT IDENTIFIER

nstructure560tr		1.3.6.1.4.1.343.5.1.13
OBJECT IDENTIFIER

nstructure560fr		1.3.6.1.4.1.343.5.1.14
OBJECT IDENTIFIER

routers		1.3.6.1.4.1.343.5.2
OBJECT IDENTIFIER

express9100		1.3.6.1.4.1.343.5.2.1
OBJECT IDENTIFIER

express920x		1.3.6.1.4.1.343.5.2.2
OBJECT IDENTIFIER

express9300		1.3.6.1.4.1.343.5.2.3
OBJECT IDENTIFIER

express9400		1.3.6.1.4.1.343.5.2.4
OBJECT IDENTIFIER

express8100st		1.3.6.1.4.1.343.5.2.5
OBJECT IDENTIFIER

express8100u		1.3.6.1.4.1.343.5.2.6
OBJECT IDENTIFIER

express8100x		1.3.6.1.4.1.343.5.2.7
OBJECT IDENTIFIER

express8100fr		1.3.6.1.4.1.343.5.2.8
OBJECT IDENTIFIER

express9520st		1.3.6.1.4.1.343.5.2.9
OBJECT IDENTIFIER

express9520u		1.3.6.1.4.1.343.5.2.10
OBJECT IDENTIFIER

express9510st		1.3.6.1.4.1.343.5.2.11
OBJECT IDENTIFIER

express9510u		1.3.6.1.4.1.343.5.2.12
OBJECT IDENTIFIER

express9515st		1.3.6.1.4.1.343.5.2.13
OBJECT IDENTIFIER

express9515u		1.3.6.1.4.1.343.5.2.14
OBJECT IDENTIFIER

express9525st		1.3.6.1.4.1.343.5.2.15
OBJECT IDENTIFIER

express9525u		1.3.6.1.4.1.343.5.2.16
OBJECT IDENTIFIER

express8210		1.3.6.1.4.1.343.5.2.17
OBJECT IDENTIFIER

express8220		1.3.6.1.4.1.343.5.2.18
OBJECT IDENTIFIER

express9530		1.3.6.1.4.1.343.5.2.19
OBJECT IDENTIFIER

express9535		1.3.6.1.4.1.343.5.2.20
OBJECT IDENTIFIER

express9545st		1.3.6.1.4.1.343.5.2.21
OBJECT IDENTIFIER

express9545u		1.3.6.1.4.1.343.5.2.22
OBJECT IDENTIFIER

express8100wV4		1.3.6.1.4.1.343.5.2.23
OBJECT IDENTIFIER

express8100stV4		1.3.6.1.4.1.343.5.2.27
OBJECT IDENTIFIER

express8100uV4		1.3.6.1.4.1.343.5.2.28
OBJECT IDENTIFIER

hubs		1.3.6.1.4.1.343.5.3
OBJECT IDENTIFIER

express110-12		1.3.6.1.4.1.343.5.3.1
OBJECT IDENTIFIER

express110-24		1.3.6.1.4.1.343.5.3.2
OBJECT IDENTIFIER

express210-12		1.3.6.1.4.1.343.5.3.3
OBJECT IDENTIFIER

express210-24		1.3.6.1.4.1.343.5.3.4
OBJECT IDENTIFIER

express220-12		1.3.6.1.4.1.343.5.3.5
OBJECT IDENTIFIER

express220-24		1.3.6.1.4.1.343.5.3.6
OBJECT IDENTIFIER

express330-16		1.3.6.1.4.1.343.5.3.7
OBJECT IDENTIFIER

express330-24		1.3.6.1.4.1.343.5.3.8
OBJECT IDENTIFIER

stacks		1.3.6.1.4.1.343.5.4
OBJECT IDENTIFIER

nstructure560		1.3.6.1.4.1.343.5.4.1
OBJECT IDENTIFIER

nstructure560s		1.3.6.1.4.1.343.5.4.1.1
OBJECT IDENTIFIER

nstructure560l3s		1.3.6.1.4.1.343.5.4.1.2
OBJECT IDENTIFIER

mib2ext		1.3.6.1.4.1.343.6
OBJECT IDENTIFIER

system		1.3.6.1.4.1.343.6.1
OBJECT IDENTIFIER

ip		1.3.6.1.4.1.343.6.2
OBJECT IDENTIFIER

snmp		1.3.6.1.4.1.343.6.3
OBJECT IDENTIFIER

hw		1.3.6.1.4.1.343.7
OBJECT IDENTIFIER

stack		1.3.6.1.4.1.343.7.1
OBJECT IDENTIFIER

chassis		1.3.6.1.4.1.343.7.2
OBJECT IDENTIFIER

modules		1.3.6.1.4.1.343.7.3
OBJECT IDENTIFIER

mediamodules		1.3.6.1.4.1.343.7.4
OBJECT IDENTIFIER

ports		1.3.6.1.4.1.343.7.5
OBJECT IDENTIFIER

stackext		1.3.6.1.4.1.343.7.11
OBJECT IDENTIFIER

chassisext		1.3.6.1.4.1.343.7.12
OBJECT IDENTIFIER

modulesext		1.3.6.1.4.1.343.7.13
OBJECT IDENTIFIER

mediamodulesext		1.3.6.1.4.1.343.7.14
OBJECT IDENTIFIER

portsext		1.3.6.1.4.1.343.7.15
OBJECT IDENTIFIER

sysVendorName		1.3.6.1.4.1.343.6.1.1
Must return: Intel Corporation.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(128)

sysProductName		1.3.6.1.4.1.343.6.1.2
Full name of device. Excludes the Sub Type information.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(128)

sysProductSubType		1.3.6.1.4.1.343.6.1.3
Sub Type description of device. For example, national, special, or test versions.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(128)

sysMibVersion		1.3.6.1.4.1.343.6.1.4
Version of the INTEL-GEN-MIB supported by the device's SNMP agent. Syntax: A.BC xxx A (1-9): Changes when B overflows, or when object STATUS is changed to obsolete. B (0-9): Changed when new (major) object(s) are added to the MIB (Not objects below the sysProducts section). C (0-9): Changed when adding a new enumeration or making minor changes to an object. xxx: For Intel internal use only Version Log: 1.00: First version.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(8)

sysTimeOfDay		1.3.6.1.4.1.343.6.1.5
The device's expression of the local date and time of day. The time is expressed in seconds since midnight (0 hour), January 1, 1970. 0 is returned if the device does not support a real-time clock.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

sysSystemDate		1.3.6.1.4.1.343.6.1.6
The device's expression of the local date, time of day, and time zone. The syntax is identical to the DateAndTime format defined in RFC-1514. field octets contents range _____ ______ ________ _____ 1 1-2 year 0..65536 (in network byte order) 2 3 month 1..12 3 4 day 1..31 4 5 hour 0..23 5 6 minutes 0..59 6 7 seconds 0..60 (use 60 for leap-second) 7 8 deci-seconds 0..9 8 9 direction from UTC '+' / '-' (in ASCII notation) 9 10 hours from UTC 0..11 10 11 minutes from UTC 0..59 Note: If only the local time is known, then time-zone information (fields 8-10) is not present. An empty string is returned if the device does not support a real-time clock.
Status: optional	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..11)

sysReset		1.3.6.1.4.1.343.6.1.7
Resets the agent/device. resetCold(1): Restarts as if the device was powered off then on. resetWarm(2): Restarts the currently active software. resetStackCold(3): Restarts a multi agent stack as if the stack was powered off then on. resetStackWarm(4): Restarts the currently active software for each devices in a multi agent stack.
Status: mandatory	Access: write-only
OBJECT-TYPE
	INTEGER	resetCold(1), resetWarm(2), resetStackCold(3), resetStackWarm(4)

sysConfTable		1.3.6.1.4.1.343.6.1.8
This table is used to describe the state of the device's configuration.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SysConfEntry

sysConfEntry		1.3.6.1.4.1.343.6.1.8.1
Configuration information entry: Index 1 is the active configuration. Index 2 is the backup configuration (if it exists).
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SysConfEntry

confStatus		1.3.6.1.4.1.343.6.1.8.1.1
unknown(1): default(2): (Index 1) default configuration. loaded(3): (Index 1) configuration loaded from a TFTP server. changed(4): (Index 1) modified, but not copied to the backup. saved(5): (Index 1) active configuration and backup copies are identical. (Index 2) always returns 'saved(5)' (if it exists).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), default(2), loaded(3), changed(4), saved(5)

confName		1.3.6.1.4.1.343.6.1.8.1.2
The configuration filename (0 to 256 bytes). Use this name when using TFTP to download the configuration. An empty string is returned if configuration files are not supported for the device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..256)

confTime		1.3.6.1.4.1.343.6.1.8.1.3
sysTimeOfDay of the last time the configuration was modified, loaded, or saved to backup.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

confTftpIp		1.3.6.1.4.1.343.6.1.8.1.4
IP address of the TFTP server from which the configuration was loaded. 0 is returned if the configuration was not loaded from a server.
Status: mandatory	Access: read-only
OBJECT-TYPE
	IpAddress

sysConfChange		1.3.6.1.4.1.343.6.1.9
Object used to activate and backup configurations: useDefaultConf(1): Load the factory default configuration as the active configuration. useDefaultConfKeepIp(2): Same as useDefaultConf(1), but keep the current IP address. useBackupConf(3): Load the backup configuration as the active configuration. createBackupConf(4): Save the active configuration as the backup configuration. createDefBackupConf(5): Combine useDefaultConf(1) and createBackupConf(4) and use as the factory default. useStackBackupConf(6): Load the backup configuration as the active configuration. For all modules in a stack. createStackBackupConf(7):Save the active configuration as the backup configuration. For all modules in a stack. stackTftpUploadLock(8): Lock for TFTP upload of configuration to all modules in a stack. Used to syncronise external backup configuration actions. 60 sec inactivity timeout on the lock. stackTftpUploadUnlockActivate(9): Unlock and activate uploaded configuration for for all modules in a stack. stackTftpUploadUnlockCancel(10): Unlock and cancel uploaded configuration for for all modules in a stack. stackTftpUploadKeepAlive(11): Inform device that TFTP upload still in progress and mgt station is alive. stackUseDefaultConf(12): Load the factory default configuration as the active configuration for each device in a multi agent stack. stackUseDefaultConfKeepIp(13): Same as stackUseDefaultConf(1), but keep the current IP addresses. stackCreateDefBackupConf(14): Combine stackUseDefaultConf(12) and createStackBackupConf(7). Thus, restore the factory default configuration and save it as the backup configuration for all modules in the stack.
Status: mandatory	Access: write-only
OBJECT-TYPE
	INTEGER	useDefaultConf(1), useDefaultConfKeepIp(2), useBackupConf(3), createBackupConf(4), createDefBackupConf(5), useStackBackupConf(6), createStackBackupConf(7), stackTftpUploadLock(8), stackTftpUploadUnlockActivate(9), stackTftpUploadUnlockCancel(10), stackTftpUploadKeepAlive(11), stackUseDefaultConf(12), stackUseDefaultConfKeepIp(13), stackCreateDefBackupConf(14)

sysLogTable		1.3.6.1.4.1.343.6.1.10
This table is used to configure and monitor the agent's log files. The log files are read with TFTP.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SysLogEntry

sysLogEntry		1.3.6.1.4.1.343.6.1.10.1
Entry with a description of a log.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SysLogEntry

logType		1.3.6.1.4.1.343.6.1.10.1.1
The type of log: logSystem(1): Log of system events. logError(2): Log of errors.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	logSystem(1), logError(2)

logEntries		1.3.6.1.4.1.343.6.1.10.1.2
The number of entries in the log. Setting the value to zero will clear the log. Setting any other value is invalid.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

logFileName		1.3.6.1.4.1.343.6.1.10.1.3
Filename of the log file. Use this name when using TFTP to download the log.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(128)

logLastChanged		1.3.6.1.4.1.343.6.1.10.1.4
sysUpTime of the last change to the log.
Status: mandatory	Access: read-only
OBJECT-TYPE
	TimeTicks

sysConfRollbackTimeout		1.3.6.1.4.1.343.6.1.11
This object is used to activate and deactivate the configuration rollback mechanism. Set to 0 to deactivate. Set to x (x > 0) to activate in x seconds.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

sysConfChangeLastResponse		1.3.6.1.4.1.343.6.1.12
This object is used in conjunction with the sysConfChange object, to be read after setting a value for sysConfChange to obtain status of that operation. When this object returns notReady(99) snmp client must poll again, until it returns a valid response different from notReady(99). success(1): Last SET request of SysConfChange object was successful. Mgt station should continue process. noEditingRightsVlan(2): The VLAN configuration is busy, probable causes: VLAN is being edited somewhere else (editToken taken) VLAN is distributing configuration among the switches Mgt station should check the editToken state and advice the user to wait or force a release of the token, if taken. If not taken advice user to wait until configuration is no longer busy and try again. noEditingRightsLocalParm(3): A switch is having the local parameters modified. Mgt station should advice user to wait and try again. flashOperationFailed(4): A switch failed loading the configuration from Flash. Mgt station should advice user to check status of the switches and possibly try again later. flashOperationNothingToLoad(5): The contacted switch didn't have a configuration saved in Flash + Mgt station should advice the user that this switch never had a configuration saved, and the load from Flash has been aborted. This could occur if the contacted switch is new in the stack, and thus haven't had anything saved yet, or if the user simply never saved anything in Flash. Mgt station should advice user to save configuration in flash for entire stack always. tftpOperationFailed(6): The TFTP of files to the switches failed Mgt station should advice user to check status of the switches and possibly try again later. tftpOperationNoLock(7): The stack TFTP lock has not been set by Mgt station. Mgt station should advice user that someone may have tampered with the stack (reset, re-config) while the process was ongoing. (This could also be due to an error by the Mgt platform or switch) tftpOperationStackMemberMissingParmFile(8): One or more of the switches in the stack (other than the contacted switch) didn't receive a parameter block file yet. Mgt station should advice user to check status of the stack, if new switches were added since the configuration was backed-up, or during the process, this could be the problem. tftpOperationMissingParmFile(9): The contacted switch didn't receive a parameter block file yet. Mgt should advice user that a proper parameter block file wasn't received on the contacted switch. Data may have been corrupted. tftpOperationMissingNvpFile(10): The contacted switch didn't receive a network vlan policy file yet. Mgt should advice user that a proper nvp file wasn't received on the contacted switch. Data may have been corrupted. tftpOperationMgtTimeout(11): The contacted switch didn't receive a keep-alive signal from the Mgt station for 60 seconds. If Mgt is still there it should advice the user to check connection between Mgt station and switch. factoryDefaultOperationFailed(12): A switch failed loading the configuration from default parameters. Mgt station should advice user to check status of the switches and possibly try again later. stackMemberRejectsOperation(13): A switch (other than the contacted) couldn't initiate the desired operation. Mgt should advice the user to check the stack status. If switches were added or removed during the operation this may have caused the problem. intraStackCommunicationError(16): Communication between the stack members failed. Mgt should advice user to check cable connections and status of the switches, and possibly try operation again. internalError(17): This should never occur, and would indicate that a switch is in a fatal state of error. Mgt should advice the user to report the problem to support. notReady(99):
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	success(1), noEditingRightsVlan(2), noEditingRightsLocalParm(3), flashOperationFailed(4), flashOperationNothingToLoad(5), tftpOperationFailed(6), tftpOperationNoLock(7), tftpOperationStackMemberMissingParmFile(8), tftpOperationMissingParmFile(9), tftpOperationMissingNvpFile(10), tftpOperationMgtTimeout(11), factoryDefaultOperationFailed(12), stackMemberRejectsOperation(13), intraStackCommunicationError(16), internalError(17), notReady(99)

sysLocalMangementTimeout		1.3.6.1.4.1.343.6.1.13
The users conection to the local management system will be terminated by the device if it is idle for more than this timeout value. Time is in minutes. 0 indicates no termination will occour.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

ipConfTable		1.3.6.1.4.1.343.6.2.1
IP configuration table: The first table entry (index 1) shows the current values. The second entry (index 2) contains the values you wish to set. To activate the second entry, set ipConf2Activate = active(1).
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IpConfEntry

ipConfEntry		1.3.6.1.4.1.343.6.2.1.1
This table is used to view and modify the agent's IP configuration: Index 1 is the currently active configuration (read only). Index 2 is the new configuration, which is activated by setting ipConf2Activate = active(1).
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	IpConfEntry

ipAddressAssignment		1.3.6.1.4.1.343.6.2.1.1.1
Determines how the management agent gets its IP configuration: fixed(1): Get configuration from ipAddress, ipSubNetMask, ... in this table. bootp(2): Get configuration from a BOOTP server (ipBootpServerAddress).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	fixed(1), bootp(2)

ipAddress		1.3.6.1.4.1.343.6.2.1.1.2
IP address for the device and agent.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

ipSubNetMask		1.3.6.1.4.1.343.6.2.1.1.3
Network (subnet) mask for the device and agent.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

ipRouterAddress		1.3.6.1.4.1.343.6.2.1.1.4
Gateway (router) address for the device and agent.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

ipBroadcastAddress		1.3.6.1.4.1.343.6.2.1.1.5
Broadcast address for the device and agent.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

ipBootpServerAddress		1.3.6.1.4.1.343.6.2.1.1.6
If ipAddressAssignment = bootp(2), then this is the IP address of the BOOTP/DHCP server used to get the current address. If 0.0.0.0, then BOOTP/DHCP requests are multicasted.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

ipConf2Activate		1.3.6.1.4.1.343.6.2.2
Activates the second IP configuration set. Warning! This may reset the device in some implementations.
Status: mandatory	Access: write-only
OBJECT-TYPE
	INTEGER	active(1)

ipModuleConfTable		1.3.6.1.4.1.343.6.2.3
IP module configuration table: This is a version of the ipConfTable indexed by Chassis, Module
Status: optional	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IpModuleConfEntry

ipModuleConfEntry		1.3.6.1.4.1.343.6.2.3.1
This table is used to view and modify the module agent's IP configuration:
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	IpModuleConfEntry

ipModuleChassisIndex		1.3.6.1.4.1.343.6.2.3.1.1
Chassis number in stack that contains the module.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

ipModuleModuleIndex		1.3.6.1.4.1.343.6.2.3.1.2
Module number in the chassis.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

ipModuleConfigIndex		1.3.6.1.4.1.343.6.2.3.1.3
Configuration number in the module. Index 1 is the currently active configuration (read only). Index 2 is the new configuration, which is activated by setting ipConf2Activate = active(1).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

ipModuleAddressAssignment		1.3.6.1.4.1.343.6.2.3.1.4
Determines how the management agent gets its IP configuration: fixed(1): Get configuration from ipModuleAddress, ipModuleSubNetMask, ... in this table. bootp(2): Get configuration from a BOOTP server (ipModuleBootpServerAddress).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	fixed(1), bootp(2)

ipModuleAddress		1.3.6.1.4.1.343.6.2.3.1.5
IP address for the module.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

ipModuleSubNetMask		1.3.6.1.4.1.343.6.2.3.1.6
Network (subnet) mask for the module.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

ipModuleRouterAddress		1.3.6.1.4.1.343.6.2.3.1.7
Gateway (router) address for the module.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

ipModuleBroadcastAddress		1.3.6.1.4.1.343.6.2.3.1.8
Broadcast address for the module.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

ipModuleBootpServerAddress		1.3.6.1.4.1.343.6.2.3.1.9
If ipModuleAddressAssignment = bootp(2), then this is the IP address of the BOOTP/DHCP server used to get the current address. If 0.0.0.0, then BOOTP/DHCP requests are multicasted.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

ipModuleConf2Activate		1.3.6.1.4.1.343.6.2.4
Activates the second IP configuration set for all modules. Warning! This may reset one or more of the chassis or modules in some implementations.
Status: optional	Access: write-only
OBJECT-TYPE
	INTEGER	active(1)

ipModuleConf2Confirm		1.3.6.1.4.1.343.6.2.5
If not set to confirm(1) within a short period of time (60 sec) after ipModuleConf2Activate is set to active(1), then all modules should revert to their original ip configuration.
Status: optional	Access: write-only
OBJECT-TYPE
	INTEGER	confirm(1)

snmpAuthMaxEntries		1.3.6.1.4.1.343.6.3.1
Maximum number of entries in the access authentication table (snmpAuthTable).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

snmpAuthTableLastChange		1.3.6.1.4.1.343.6.3.2
sysUpTime of last change to snmpAuthTable.
Status: mandatory	Access: read-only
OBJECT-TYPE
	TimeTicks

snmpAuthTable		1.3.6.1.4.1.343.6.3.3
Management access authentication table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SnmpAuthEntry

snmpAuthEntry		1.3.6.1.4.1.343.6.3.3.1
Authentication entry.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SnmpAuthEntry

authNumber		1.3.6.1.4.1.343.6.3.3.1.1
A number that uniquely identifies an authentication entry.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

authProtocolAccessIpCommunity		1.3.6.1.4.1.343.6.3.3.1.2
This object contains the Protocol (1 byte), Access (1 byte), IP address (4 byte), IP subnet mask (4 byte), and Community (0 to 31 byte). Not all protocols are supported by all devices. Protocol: snmp(1), telnet(2), http(3), tftp(4), ftp(5) Access: Protocols: noAccess(1), All readOnly(2), All writeOnly(3), Not snmp(1) or telnet(2) readWrite(4), All readOnlySecureSNMPObjects(5), snmp(1) readWriteSecureSNMPObjects(6) snmp(1) If the IP address is zero, then any IP address is allowed. If the IP subnet mask is not 255.255.255.255, then any IP address is an IP network address. IP network addresses can't overlap for a given protocol. If an IP address and an IP network address overlap for a given protocol, then the access field of the IP address is used. The community string is only used for SNMP access. If the community string is zero length, then any value of community is allowed.
Status: mandatory	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(10..41)

authDelete		1.3.6.1.4.1.343.6.3.3.1.3
The snmpAuthEntry is removed when set to delete(1).
Status: mandatory	Access: write-only
OBJECT-TYPE
	INTEGER	delete(1)

snmpTrapMaxEntries		1.3.6.1.4.1.343.6.3.4
Maximum number of entries in the trapTable.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

snmpTrapTable		1.3.6.1.4.1.343.6.3.5
Host Trap list.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SnmpTrapEntry

snmpTrapEntry		1.3.6.1.4.1.343.6.3.5.1
Host Trap entry.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SnmpTrapEntry

trapNumber		1.3.6.1.4.1.343.6.3.5.1.1
A number that uniquely identifies a trap entry.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

trapIpAndGroupAndCommunity		1.3.6.1.4.1.343.6.3.5.1.2
This object contains the IP address (4 byte), the trap groups (32 bit = 4 byte), and the community (0 to 31 byte) used in the trap. The trap groups section is stored as a 32-bit little-endian value. Groups: bit 1: all traps bit 2: configuration related traps bit 3: hardware state related traps bit 4: diagnostics related traps
Status: mandatory	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(8..39)

trapDelete		1.3.6.1.4.1.343.6.3.5.1.3
The trapEntry is removed when set to delete(1).
Status: mandatory	Access: write-only
OBJECT-TYPE
	INTEGER	delete(1)

snmpAccessTable		1.3.6.1.4.1.343.6.3.6
Management access list. This is a list of all IP addresses that have passed the authentication table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SnmpAccessEntry

snmpAccessEntry		1.3.6.1.4.1.343.6.3.6.1
Management access entry.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SnmpAccessEntry

snmpAccessIP		1.3.6.1.4.1.343.6.3.6.1.1
IP addresses of devices that have successfully cleared the authentication table.
Status: mandatory	Access: read-only
OBJECT-TYPE
	IpAddress

snmpAccessTime		1.3.6.1.4.1.343.6.3.6.1.2
sysTimeOfDay of the last successful access from this IP address.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

snmpAccessProtocol		1.3.6.1.4.1.343.6.3.6.1.3
Protocol used for successful access from this IP address.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	snmp(1), telnet(2), http(3), tftp(4), ftp(5)

snmpAccessType		1.3.6.1.4.1.343.6.3.6.1.4
Types of successful access from this IP address. Access: Protocols: noAccess(1), All readOnly(2), All writeOnly(3), All except for snmp(1) and telnet(2) readWrite(4), All readOnlySecureSNMPObjects(5), snmp(1) only readWriteSecureSNMPObjects(6) snmp(1) only
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	noAccess(1), readOnly(2), writeOnly(3), readWrite(4), readOnlySecureSNMPObjects(5), readWriteSecureSNMPObjects(6)

stackClass		1.3.6.1.4.1.343.7.1.1
This object identifies which type of stack the device is a part of: standalone(1): Not a stack. (stackMaxChassis=1, chassisMaxModules=1). chassis(2): Not a stack. (stackMaxChassis=1, chassisMaxModules>1). multiagentstack(3): Stack of chassis' with their own management agents. singleagentstack(4): Stack of chassis' with a single management agent.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	standalone(1), chassis(2), multiagentstack(3), singleagentstack(4)

stackMaxChassis		1.3.6.1.4.1.343.7.1.2
The maximum number of chassis' in a stack. Returns one (1) if stackClass = standalone(1) or chassis(2).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

stackChassis		1.3.6.1.4.1.343.7.1.3
The actual number of chassis' in a stack. Returns one (1) if stackClass = standalone(1) or chassis(2).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

stackAgentChassis		1.3.6.1.4.1.343.7.1.4
Which chassis in a stack contains the agent. Possible values are 1..stackMaxChassis. Returns one (1) if stackClass = standalone(1) or chassis(2).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

stackAgentModule		1.3.6.1.4.1.343.7.1.5
Which module in the chassis selected by stackAgentChassis contains the agent. Possible values are 1..chassisMaxModules for the selected chassis. Returns one (1) if stackClass = standalone(1).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

stackUserAssignedName		1.3.6.1.4.1.343.7.1.6
User-definable information about the stack.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..24)

stackID		1.3.6.1.4.1.343.7.1.7
Unique identifier used to identify which stack a device last belonged to. Automatically genarated when a new stack is created. Based on MAC addresses.
Status: optional	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..31)

stackTopology		1.3.6.1.4.1.343.7.1.8
Stack topology type
Status: optional	Access: read-only
OBJECT-TYPE
	INTEGER	chain(1), star(2), tree(3)

stackMultiAgentDefultChassisModule		1.3.6.1.4.1.343.7.1.9
This object contains the Chassis and Module numbers to be used when using a non indexed MIB on a multi agent stack. Chassis index (4 byte (big-endian)), Module index (4 byte (big-endian))
Status: mandatory	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(8)

chassisTable		1.3.6.1.4.1.343.7.2.1
Possible values of indices are 1..stackChassis
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ChassisEntry

chassisEntry		1.3.6.1.4.1.343.7.2.1.1
Possible values of indices are 1..stackChassis
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	ChassisEntry

chassisIndex		1.3.6.1.4.1.343.7.2.1.1.1
Chassis number in the stack.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

chassisType		1.3.6.1.4.1.343.7.2.1.1.2
Hardware identification for the chassis.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	unavailable(1), campus8tx(2), campus8fx(3), desktop24tx(4), stackable12tx(5), stackable24tx(6), stackable16tx(7), desktop16tx(8)

chassisMaxModules		1.3.6.1.4.1.343.7.2.1.1.3
The maximum number of modules in this chassis. Returns one (1) if stackClass = standalone(1).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

chassisModules		1.3.6.1.4.1.343.7.2.1.1.4
The actual number of modules in this chassis. Possible values are 1..chassisMaxModules. Returns one (1) if stackClass = standalone(1).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

chassisUserAssignedType		1.3.6.1.4.1.343.7.2.1.1.5
User-definable information about the chassis.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..24)

chassisUserAssignedNumber		1.3.6.1.4.1.343.7.2.1.1.6
User-definable information about the chassis.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..24)

chassisUserAssignedName		1.3.6.1.4.1.343.7.2.1.1.7
User-definable information about the chassis.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..24)

chassisMaxPSUs		1.3.6.1.4.1.343.7.2.1.1.8
The maximum number of power supply units in this chassis. Detailed information about the power supply units is located in the psuTable (a chassis extension MIB).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

moduleTable		1.3.6.1.4.1.343.7.3.1
Possible values of indices are 1..stackMaxChassis and 1..chassisMaxModules
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ModuleEntry

moduleEntry		1.3.6.1.4.1.343.7.3.1.1
Possible values of indices are 1..stackMaxChassis and 1..chassisMaxModules
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	ModuleEntry

moduleChassisIndex		1.3.6.1.4.1.343.7.3.1.1.1
Chassis number in stack that contains the module.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

moduleIndex		1.3.6.1.4.1.343.7.3.1.1.2
Module number in the chassis.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

moduleType		1.3.6.1.4.1.343.7.3.1.1.3
Hardware identification for the module.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	unavailable(1), express550t(2), express550f(3), express510t(4), express8100st(5), express8100u(6), express8100x(7), express8100fr(8), express110p12(20), express110p24(21), express110management(22), express110bridge(23), express110managementWithRMON(24), express210p12(25), express210p24(26), express220p12(27), express220p24(28), express330p16(29), express330p24(30), express300management(31), express300txuplink(32), express300fxuplink(33), express460tp16(34), express460tp24(35), nstructure560t(36), nstructure560tr(38), nstructure560fr(39)

moduleFirstPort		1.3.6.1.4.1.343.7.3.1.1.4
The portIndex of the first port on the module.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

moduleNumberOfPorts		1.3.6.1.4.1.343.7.3.1.1.5
Number of ports on the module.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

moduleMaxMediaModules		1.3.6.1.4.1.343.7.3.1.1.6
Maximum number of media modules on the module. Returns 0 if none.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

moduleUserAssignedType		1.3.6.1.4.1.343.7.3.1.1.7
User-definable information about the module.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..24)

moduleUserAssignedNumber		1.3.6.1.4.1.343.7.3.1.1.8
User-definable information about the module.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..24)

moduleUserAssignedName		1.3.6.1.4.1.343.7.3.1.1.9
User-definable information about the module.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..24)

moduleRAM		1.3.6.1.4.1.343.7.3.1.1.10
Displays the module's RAM size in bytes.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

moduleEPROM		1.3.6.1.4.1.343.7.3.1.1.11
Displays the module's EPROM size in bytes.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

moduleFLASHPROM		1.3.6.1.4.1.343.7.3.1.1.12
Displays the module's Flash Memory size in bytes.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

moduleLEDInfo		1.3.6.1.4.1.343.7.3.1.1.13
State of all non-port LEDs on the module. There is one byte per LED: Byte 1 is the Power LED. Byte 2 is the Status LED. The rest are module specific. The most significant bit is used for blink/solid: Off = The LED is lit permanently. On = The LED blinks. The three least significant bits are used for color: 1 = not lit 2 = green 3 = yellow 4 = blue 5 = red 0+6+7 not used The four remaining bits are currently unused and must be 0.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(2..32)

moduleAllPortType		1.3.6.1.4.1.343.7.3.1.1.14
Type of all ports in the module. One byte per port. The values are coded like portType.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

moduleAllPortLEDInfo		1.3.6.1.4.1.343.7.3.1.1.15
The current state of all port LEDs on the module. X bytes per port on the module, where X = the normal number of LEDs per port on this module. There is one byte per LED. The most significant bit is used for blink/solid: Off = The LED is lit permanently. On = The LED blinks. The three least significant bits are used for color: 1 = not lit, 2 = green, 3 = yellow, 4 = blue, 5 = red, 0+6+7 not used The four remaining bits are currently unused and must be 0.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

moduleAllPortStatus		1.3.6.1.4.1.343.7.3.1.1.16
The current operational state for all ports on this module. This is an array of bit arrays which represents the state of the port. bit 0: disabled due to configuration bit 1: hardware error bit 2: no linkpulse bit 3: disabled by manager bit 4: disabled by access control bit 5: disabled by redundancy
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

moduleLastPortChange		1.3.6.1.4.1.343.7.3.1.1.17
sysUpTime of last change to any of the AllPort values above.
Status: mandatory	Access: read-only
OBJECT-TYPE
	TimeTicks

moduleMacAddress		1.3.6.1.4.1.343.7.3.1.1.18
The base MAC address allocated for MAC interfaces on this module. Returns 00,00,00,00,00,00 if not used.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(6)

moduleIpAddress		1.3.6.1.4.1.343.7.3.1.1.19
The IP address of the agent located in this module. Returns 0.0.0.0 if no agent is located in this module
Status: mandatory	Access: read-only
OBJECT-TYPE
	IpAddress

moduleSerialNumber		1.3.6.1.4.1.343.7.3.1.1.20
Module serial number.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..32)

moduleVersion		1.3.6.1.4.1.343.7.3.1.1.21
The hardware version number for this module. First version is 0, second is 1, and so on.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

moduleSwStatus		1.3.6.1.4.1.343.7.3.1.1.22
The state of the active software on the module. This is for single software devices. notsupported(1): This module does not support software. nosoftware(2): This module does not currently have software. unavailable(3): This module is currently not able get the software status. approved(4): This software is used after power off or a resetCold(1). experimental(5): Software must be approved to be used after any type of reset. The only permitted set operation is to change the status from experimental(5) to approved(4) or to change the status from approved(4) to nosoftware(2); this requires moduleBackupSwStatus == approved(4).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	notsupported(1), nosoftware(2), unavailable(3), approved(4), experimental(5)

moduleSwName		1.3.6.1.4.1.343.7.3.1.1.23
The active software's filename (0 to 256 bytes).
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..256)

moduleSwDescription		1.3.6.1.4.1.343.7.3.1.1.24
Description of the active software.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

moduleSwLoadTime		1.3.6.1.4.1.343.7.3.1.1.25
sysTimeOfDay of last time the active software was loaded from a TFTP server or flash memory.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

moduleSwTftpIp		1.3.6.1.4.1.343.7.3.1.1.26
IP address of the TFTP server from which the active software was loaded. Returns 0.0.0.0 for factory-loaded software or software loaded by a non IP-based connection to the device (for example, a serial cable connection).
Status: mandatory	Access: read-only
OBJECT-TYPE
	IpAddress

moduleBackupSwStatus		1.3.6.1.4.1.343.7.3.1.1.27
The state of the module's backup software: notsupported(1): This module does not support a backup software. nosoftware(2): This module does not currently have backup software. unavailable(3): This module is not currently able to get the backup software status. approved(4): Software is used after a resetWarm(2) unless moduleSwStatus == approved(4). experimental(5): Never returned. The only permitted set operation is to change the status from approved(4) to nosoftware(2); this requires moduleSwStatus == approved(4).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	notsupported(1), nosoftware(2), unavailable(3), approved(4), experimental(5)

moduleBackupSwName		1.3.6.1.4.1.343.7.3.1.1.28
The backup software's filename (0 to 256 bytes).
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..256)

moduleBackupSwDescription		1.3.6.1.4.1.343.7.3.1.1.29
Description of the backup software.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

moduleBackupSwLoadTime		1.3.6.1.4.1.343.7.3.1.1.30
sysTimeOfDay of last time the backup software was saved to Flash Memory.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

moduleBackupSwTftpIp		1.3.6.1.4.1.343.7.3.1.1.31
IP address of the TFTP server from which the software was originally loaded.
Status: mandatory	Access: read-only
OBJECT-TYPE
	IpAddress

moduleSwTftpIpAndSwName		1.3.6.1.4.1.343.7.3.1.1.32
This object contains the IP address of the TFTP server (4 bytes) and the software filename (0 to 256 bytes). This is used to initiate a software update. The result of the upgrade is accessible in moduleSwUpdateResult.
Status: mandatory	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(4..260)

moduleSwUpdateResult		1.3.6.1.4.1.343.7.3.1.1.33
The result of software update initiated by setting moduleSwTftpIpAndSwName: noError(1): The last upgrade ended successfully. No upgrade currently in progress. swUpdateRunning(2): An upgrade is currently in progress. errorUnknown(3): The last upgrade failed. errorNoTftpServer(4): The last upgrade failed. Server not found. errorNoSoftware(5): The last upgrade failed. File not found on server. errorSoftwareMismatch(6): The last upgrade failed. The software loaded was not for this device type. errorMoreFlash(7): The last upgrade failed. Insufficient Flash Memory. errorMoreRAM(8): The last upgrade failed. Insufficient RAM.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	noError(1), swUpdateRunning(2), errorUnknown(3), errorNoTftpServer(4), errorNoSoftware(5), errorSoftwareMismatch(6), errorMoreFlash(7), errorMoreRAM(8)

moduleSpecificObject		1.3.6.1.4.1.343.7.3.1.1.34
Used for module specific configuration.
Status: mandatory	Access: write-only
OBJECT-TYPE
	OCTET STRING	Size(0..256)

moduleTemperatureStatus		1.3.6.1.4.1.343.7.3.1.1.35
Indication of the modules temperature. normal(1): Temperature within normal opperational specification high(2): Temperature obove normal opperational specification (Check air circulation) critical(3): Temperature critically obove normal opperational specification (Chut device the device imediatlly) unavailable(99): No temperature censor in the device.
Status: optional	Access: read-only
OBJECT-TYPE
	INTEGER	normal(1), high(2), critical(3), unavailable(99)

moduleBootSectionVersion		1.3.6.1.4.1.343.7.3.1.1.36
The version number for the Boot section of this module. Major version number = moduleBootSectionVersion / 256 Minor version number = moduleBootSectionVersion % 256
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mediaModuleTable		1.3.6.1.4.1.343.7.4.1
Possible values of indices are 1..moduleMaxMediaModules
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MediaModuleEntry

mediaModuleEntry		1.3.6.1.4.1.343.7.4.1.1
Possible values of indices are 1..stackMaxChassis, 1..chassisMaxModules and 1..moduleMaxMediaModules
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	MediaModuleEntry

mediaModuleChassisIndex		1.3.6.1.4.1.343.7.4.1.1.1
The chassis number that contains the module that contains the media modules.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mediaModuleModuleIndex		1.3.6.1.4.1.343.7.4.1.1.2
The module number that contains the media module.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mediaModuleIndex		1.3.6.1.4.1.343.7.4.1.1.3
Media module number in the module.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mediaModuleType		1.3.6.1.4.1.343.7.4.1.1.4
The product identification of the media module.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	unavailable(1), mediaModule4tx(2), mediaModule2fx(3), mediaModuleSMM(4), mediaModule1sx(5), mediaModuleMMM(6), mediaModule1sxSMM(7), mediaModule1lxSMM(8), mediaModule1atmmm(9), mediaModule1atmsm(10), mediaModule1atmutp(11), mediaModule1lx(12), mediaModule1000bt(13)

mediaModuleFirstPort		1.3.6.1.4.1.343.7.4.1.1.5
The portIndex of the first port on the media module.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mediaModuleNumberOfPorts		1.3.6.1.4.1.343.7.4.1.1.6
The number of ports on the media module.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

mediaModuleVersion		1.3.6.1.4.1.343.7.4.1.1.7
Hardware version number for this media module. First version is 0, second is 1, and so on.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

portTable		1.3.6.1.4.1.343.7.5.1
Possible values of indices are 1..chassisModules
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PortEntry

portEntry		1.3.6.1.4.1.343.7.5.1.1
Possible values of indices are 1..chassisModules
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	PortEntry

portChassisIndex		1.3.6.1.4.1.343.7.5.1.1.1
The chassis number that contains the module.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

portModuleIndex		1.3.6.1.4.1.343.7.5.1.1.2
The module number that contains the port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

portIndex		1.3.6.1.4.1.343.7.5.1.1.3
The port number in the module.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

portMediaModuleIndex		1.3.6.1.4.1.343.7.5.1.1.4
The media module number in the module. Returns 0 if the port is not on a media module.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

portIfIndex		1.3.6.1.4.1.343.7.5.1.1.5
The index value which uniquely identifies the interface to which this port is assigned. This is the same interface as identified by the same value of ifIndex. Returns 0 if the port is not a part of an interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

portType		1.3.6.1.4.1.343.7.5.1.1.6
Type of the port. tpfd(1) : 10Mb Twisted pair full duplex port fomm(2) : 10Mb Fiber-optic multi-mode port fosm(3) : 10Mb Fiber-optic single-mode port hundredbasetx(4) : 100Mb Twisted pair port hundredbasefx(5) : 100Mb Fiber-optic port core(6) : Stack interface port serialwan(7) : Serial Wan Interface Port isdnU(8) : ISDN Basic Rate U interface isdnST(9) : ISDN Basic Rate S/T Interface gigabasesxlx(10) : 1Gb sx or lx port tenbasetx(11) : 10Mb Twisted pair port oc3mm(12) : ATM oc3 multi mode 155MB port oc3sm(13) : ATM oc3 single mode 155MB port utp5(14) : ATM 155MB utp5 port csu(15) : 1,544 Mb T1 Channel Service Unit port console(16) : RS-232 Console port gigabasesx(17) : 1Gb sx port gigabaselx(18) : 1Gb lx port gigabaset(19) : 1Gb tx port
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	tpfd(1), fomm(2), fosm(3), hundredbasetx(4), hundredbasefx(5), core(6), serialwan(7), isdnU(8), isdnST(9), gigabasesxlx(10), tenbasetx(11), oc3mm(12), oc3sm(13), utp5(14), csu(15), console(16), gigabasesx(17), gigabaselx(18), gigabaset(19)

portStatus		1.3.6.1.4.1.343.7.5.1.1.7
The current operational state. This is a bit array which represents the state of the port. bit 0: disabled by configuration bit 1: hardware error bit 2: no link pulse bit 3: disabled by manager bit 4: disabled by access control bit 5: disabled by redundancy
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

portLEDInfo		1.3.6.1.4.1.343.7.5.1.1.8
State of all LEDs for the port (external ports only). There is one byte per LED. The most significant bit is used for blink/solid: Off = The LED is lit permanently. On = The LED blinks. The three least significant bits are used for color: 1 = not lit 2 = green 3 = yellow 4 = blue 5 = red 0+6+7 not used The four remaining bits are currently unused and must be 0.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

portTimeSinceLastStateChange		1.3.6.1.4.1.343.7.5.1.1.9
sysUpTime of last portState change.
Status: mandatory	Access: read-only
OBJECT-TYPE
	TimeTicks

portResetAllCounters		1.3.6.1.4.1.343.7.5.1.1.10
Reset all port counters to zero. This is not recommended because it violates the SNMP specification.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	reset(1), notreset(2)

portReset		1.3.6.1.4.1.343.7.5.1.1.11
Reset the port at the media level.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	reset(1), notreset(2), holdinreset(3)

portLastErrorID		1.3.6.1.4.1.343.7.5.1.1.12
Type of last error that occurred on the port since the last link status change. badPhy is a hardware problem with the hub port. polarity means there's a cabling problem between the hub and the attached device. wrongSpeedLP means the device attached to the port is operating at the wrong speed. jabberSeen means you may have a faulty device attached to the port. partition means the port was automatically partitioned at least once.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	noError(1), badPhy(2), polarity(3), wrongSpeedLP(4), jabberSeen(5), partition(6), reserved1(7), reserved2(8)

portUserAssignedName		1.3.6.1.4.1.343.7.5.1.1.13
User-definable information about the port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..32)

snmpAuthViolation		1
This trap is sent when a device attempting to access the device fails to pass the snmpAuthTable for any of the supported protocols. If it is the SNMP protocol that is violated then the device must also send the 'Authentication failure' trap defined in MIB-2.
TRAP-TYPE

snmpLoginViolation		2
This trap is sent when a device attempting to access the device fails to pass the user/password authentication for any of the supported protocols.
TRAP-TYPE

chassisInserted		1
This trap is sent when a chassis is inserted in the stack.
TRAP-TYPE

chassisRemoved		2
This trap is sent when a chassis is removed from the stack.
TRAP-TYPE

moduleInserted		1
This trap is sent when a module is inserted in the chassis.
TRAP-TYPE

moduleRemoved		2
This trap is sent when a module is removed from the chassis.
TRAP-TYPE

moduleTemperatureEvent		3
This trap indicates that the temparature of the module has changed
TRAP-TYPE

mediaModuleInserted		1
This trap is sent when a media module is inserted in the chassis/module.
TRAP-TYPE

mediaModuleRemoved		2
This trap is sent when a media module is removed from the chassis/module.
TRAP-TYPE