INTEL-ES480-QOS-MIB

File: INTEL-ES480-QOS-MIB.mib (7435 bytes)

Imported modules

SNMPv2-SMI RFC-1212 SNMPv2-TC
RFC1213-MIB INTEL-ES480-VLAN-MIB INTEL-ES480-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE TruthValue
DisplayString RowStatus es480tVlanIfIndex
es480tAgent

Defined Types

Es480tQosProfileEntry  
SEQUENCE    
  es480tQosProfileIndex INTEGER
  es480tQosProfileName DisplayString
  es480tQosProfileMinBw INTEGER
  es480tQosProfileMaxBw INTEGER
  es480tQosProfilePriority INTEGER
  es480tQosProfileRowStatus RowStatus

Es480tQosByVlanMappingEntry  
SEQUENCE    
  es480tQosByVlanMappingQosProfileIndex INTEGER

Defined Values

es480tQos 1.3.6.1.4.1.343.6.60.3
Intel ES480T Quality-of-Service objects
MODULE-IDENTITY    

es480tQosCommon 1.3.6.1.4.1.343.6.60.3.1
OBJECT IDENTIFIER    

es480tQosMode 1.3.6.1.4.1.343.6.60.3.1.4
Indicates which QoS mode the device should use. ingress(1) applies priority-based QoS based on the incoming packet's destination IP or MAC address, 802.1p priority, PACE(tm), Source Port or VLAN. egress(2) applies priority- and bandwidth-based QoS based on destination IP or MAC address or VLAN.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ingress(1), egress(2)  

es480tQosUnconfigure 1.3.6.1.4.1.343.6.60.3.1.5
Setting this to true will reset all QoS settings in the device to factory defaults. Reads from this value return an undefined value.
Status: mandatory Access: read-write
OBJECT-TYPE    
  TruthValue  

es480tQosProfileTable 1.3.6.1.4.1.343.6.60.3.1.6
This table lists QoS profiles.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Es480tQosProfileEntry

es480tQosProfileEntry 1.3.6.1.4.1.343.6.60.3.1.6.1
An individual QoS profile Entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Es480tQosProfileEntry  

es480tQosProfileIndex 1.3.6.1.4.1.343.6.60.3.1.6.1.1
An index that uniquely identifies an entry in the qos table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

es480tQosProfileName 1.3.6.1.4.1.343.6.60.3.1.6.1.2
A unique qos profile name.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..127)  

es480tQosProfileMinBw 1.3.6.1.4.1.343.6.60.3.1.6.1.3
The minumum percentage of bandwidth that this queue requires. The Switch is required to provide the minumum amount of bandwidth to the queue. The lowest possible value is 0%.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

es480tQosProfileMaxBw 1.3.6.1.4.1.343.6.60.3.1.6.1.4
The maximum percentage of bandwidth that this queue is permitted to use
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

es480tQosProfilePriority 1.3.6.1.4.1.343.6.60.3.1.6.1.5
The level of priority in which this queue will be serviced by the Switch.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER low(1), lowNormal(2), normal(3), normalMedium(4), medium(5), mediumHi(6), high(7), highHi(8)  

es480tQosProfileRowStatus 1.3.6.1.4.1.343.6.60.3.1.6.1.6
The status of the es480tQosProfile entry. This OBJECT can be set to: active(1) createAndGo(4) createAndWait(5) destroy(6) The following values may be read: active(1) notInService(2) notReady(3). Setting this object to createAndGo(4) causes the agent to attempt to create and commit the row based on the contents of the objects in the row. If all necessary information is present in the row and the values are acceptible to the agent, the agent will change the status to active(1). If any of the necessary objects are not available, the agent will reject the creation request. Setting this object to createAndWait(5) causes a row in this table to be created. The agent sets the status to notInService(2) if all of the information is present in the row and the values are acceptable to the agent; otherwise, the agent sets the status to notReady(3). Setting this object to active(1) is only valid when the current status is active(1) or notInService(2). When the state of the row transitions is set to active(1), the agent creates the corresponding row in the ifTable.. Setting this object to destroy(6) will remove the corresponding QoS Profile Entry. In order for a set of this object to destroy(6) to succeed, all dependencies on this row must have been removed. These will include any stacking dependencies in the ifStackTable and any protocol specific tables dependencies.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

es480tQosByVlanMappingTable 1.3.6.1.4.1.343.6.60.3.1.7
Table to associate a Vlan with the QoS profile that the Vlan is using. Every Vlan is assigned a Qos Profile and hence there is an entry in this table corresponding to every entry in the es480tVlanIfTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Es480tQosByVlanMappingEntry

es480tQosByVlanMappingEntry 1.3.6.1.4.1.343.6.60.3.1.7.1
The QoS associated with a particular Vlan.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Es480tQosByVlanMappingEntry  

es480tQosByVlanMappingQosProfileIndex 1.3.6.1.4.1.343.6.60.3.1.7.1.1
Value of es480tQosProfileIndex that uniquely identifies a QoS Profile entry in es480tQosProfileTable. This indicates the QoS to be given to traffic for this Vlan in the absence of any other more specific configuration information for this traffic.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535