IBM-LES-LECS-MIB
File:
IBM-LES-LECS-MIB.mib (8058 bytes)
Imported modules
Imported symbols
Defined Types
LesLecsConfEntry |
|
SEQUENCE |
|
|
|
|
lesLecsOperStatus |
INTEGER |
|
|
lesLecsAdminStatus |
INTEGER |
|
|
lesLecsAtmDevNum |
INTEGER |
|
|
lesLecsUseBurnedInEsi |
TruthValue |
|
|
lesLecsConfiguredEsi |
AtmPrivateAddrEsi |
|
|
lesLecsConfiguredSelector |
AtmSelector |
|
|
configDirectVccType |
AtmVccTrafficType |
|
|
configDirectPcr |
Bandwidth |
|
|
configDirectScr |
Bandwidth |
|
|
lesLecsAtmDevLineSpeed |
Integer32 |
|
|
lesLecsConfRowStatus |
RowStatus |
|
Defined Values
lesLecsConfTable |
1.3.6.1.4.1.2.6.118.1.2.1.2.1.1 |
This table contains the the configuration for LES-LECS interfaces. |
Status: mandatory |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
LesLecsConfEntry |
|
lesLecsConfEntry |
1.3.6.1.4.1.2.6.118.1.2.1.2.1.1.1 |
Each entry in this table contains configuration parameters for the
LES-LECS operation for an individual ATM physical interface.
Object lesLecsRowStatus is required during
row creation and deletion. |
Status: mandatory |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
LesLecsConfEntry |
|
|
lesLecsOperStatus |
1.3.6.1.4.1.2.6.118.1.2.1.2.1.1.1.1 |
The operational state of LES/LECS on this entry.
Other defines the transition states between up and down. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
other(1), up(2), down(3) |
|
lesLecsAdminStatus |
1.3.6.1.4.1.2.6.118.1.2.1.2.1.1.1.2 |
The administrative state of the LES/LECS on this entry. |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
up(2), down(3) |
|
lesLecsAtmDevNum |
1.3.6.1.4.1.2.6.118.1.2.1.2.1.1.1.3 |
Identifies ATM device to be used to interface with LECS. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..255 |
|
lesLecsAtmDevLineSpeed |
1.3.6.1.4.1.2.6.118.1.2.1.2.1.1.1.4 |
Line Speed of LECS ATM Device.
This should not exposed to the user. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Integer32 |
|
|
lesLecsUseBurnedInEsi |
1.3.6.1.4.1.2.6.118.1.2.1.2.1.1.1.5 |
Specifies whether a MAC Address burned into the ATM
device should be used as the End System Identifier
component of local ATM Address used when calling LECS. |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
TruthValue |
|
|
configDirectVccType |
1.3.6.1.4.1.2.6.118.1.2.1.2.1.1.1.8 |
Specifies type of traffic characteristics to be
associated with Configuration Direct VCC to LECS.
Bandwidth is not reserved for best effort traffic. |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
AtmVccTrafficType |
|
|
configDirectPcr |
1.3.6.1.4.1.2.6.118.1.2.1.2.1.1.1.9 |
Specifies the Peak Cell Rate (PCR) Traffic Parameter
for the Configuration Direct VCC to the LECS. The
specified rate is used for both forward and backward
directions. When a best effort connection is rejected
due to the PCR, the call may be automatically retried
with a lower PCR. Retries are performed under the
following conditions:
if (rejected PCR > 100 Mbps)
retry with PCR = 100 Mbps
else if (25 < rejected PCR <= 100 Mbps)
retry with PCR = 25 Mbps |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Bandwidth |
|
|
configDirectScr |
1.3.6.1.4.1.2.6.118.1.2.1.2.1.1.1.10 |
Specifies the Sustained Cell Rate (SCR) Traffic
Parameter for the Configuration Direct VCC to the
LECS. The specified rate is used for both forward
and backward directions. If the SCR equals the PCR
specified in LECS-INTF-7, the call is signalled
with PCR only. If SCR is signalled, the Maximum
Burst Size traffic parameter is set to accomodate
the maximum control frame size of 1516 bytes. |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Bandwidth |
|
|
lesLecsConfRowStatus |
1.3.6.1.4.1.2.6.118.1.2.1.2.1.1.1.11 |
This object is used to create or
delete entries in the lesLecsConfTable. |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
RowStatus |
|
|