HUAWEI-WLAN-SYS-MIB

File: HUAWEI-WLAN-SYS-MIB.mib (45640 bytes)

Imported modules

HUAWEI-WLAN-MIB SNMPv2-CONF SNMPv2-SMI

Imported symbols

hwWlan OBJECT-GROUP MODULE-COMPLIANCE
IpAddress Integer32 Unsigned32
OBJECT-TYPE MODULE-IDENTITY

Defined Values

hwWlanSysManagement 1.3.6.1.4.1.2011.6.139.1
add table of hwWlanStaIpv6Switch,and notes for sta ipv6 service.
MODULE-IDENTITY    

hwWlanTrapRestrain 1.3.6.1.4.1.2011.6.139.1.1
OBJECT IDENTIFIER    

hwWlanTrapRestrainAll 1.3.6.1.4.1.2011.6.139.1.1.1
All wlan trap restrain switch. If this switch is enabled, all the traps on ac will not be sent.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hwWlanTrapSeverityRestrain 1.3.6.1.4.1.2011.6.139.1.1.2
OBJECT IDENTIFIER    

hwWlanTrapSeverityRestrainSeverity 1.3.6.1.4.1.2011.6.139.1.1.2.1
Wlan trap restrain by severity. critical: means the trap whose severity is not higner than critical will not be sent. major: means the trap whose severity is not higner than major will not be sent. minor: means the trap whose severity is not higner than minor will not be sent. warning: means the trap whose severity is not higner than warning will not be sent. none: means all the severities of traps can be sent.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER critical(1), major(2), minor(3), warning(4), none(5)  

hwWlanApRegionTrapRestrain 1.3.6.1.4.1.2011.6.139.1.1.3
OBJECT IDENTIFIER    

hwWlanApRegionTrapRestrainRegionIndexMask 1.3.6.1.4.1.2011.6.139.1.1.3.1
Wlan trap restrain by ap region. Every bit is used to describe the region's trap will be restrained or not. 0 means not restrain, and 1 means restrain. Each Byte describes 8 regions are restrained or not. The value of this node is hexadecimal integer block. For example, the first Byte describes region 0~7 is restrained or not, and the second Byte describes region 8~15 is restrained or not. Such as, if only region 0,4,5,6,7,9 is restrain, the binary number is 11110001 and 00000010, the hexadecimal number is 0xF1 and 0x2, so the first Byte of this node is 0xF1, and the second Byte is 0x2.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

hwWlanApTrapRestrain 1.3.6.1.4.1.2011.6.139.1.1.4
OBJECT IDENTIFIER    

hwWlanApTrapRestrainApIndexMask 1.3.6.1.4.1.2011.6.139.1.1.4.1
Wlan trap restrain by ap. Every bit is used to describe the ap's trap will be restrained or not. 0 means not restrain, and 1 means restrain. Each Byte describes 8 aps are restrained or not. The value of this node is hexadecimal integer block. For example, the first Byte describes ap 0~7 is restrained or not, and the second Byte describes ap 8~15 is restrained or not. Such as, if only ap 0,4,5,6,7,9 is restrain, the binary number is 11110001 and 00000010, the hexadecimal number is 0xF1 and 0x2, so the first Byte of this node is 0xF1, and the second Byte is 0x2.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

hwWlanSysPara 1.3.6.1.4.1.2011.6.139.1.2
OBJECT IDENTIFIER    

hwWlanCarrierId 1.3.6.1.4.1.2011.6.139.1.2.1
The carrier identification. cmcc means 'China mobile communications corporation' , ctc means 'China telecom company' , cuc means 'China unicom company', other means 'Other company',
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER cmcc(1), ctc(2), cuc(3), other(65535)  

hwWlanAcId 1.3.6.1.4.1.2011.6.139.1.2.2
The ac identification. The carrier must set ac id and carrier id before use. In this case, APs can check each other whether blong to a same AC.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwWlanForwardMode 1.3.6.1.4.1.2011.6.139.1.2.3
AC forward mode.It can be set ess(1): ess mode ap(2): ap mode
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER ess(1), ap(2)  

hwWlanAcNEnumber 1.3.6.1.4.1.2011.6.139.1.2.4
Description.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

hwWlanAcAccessMaxApNumber 1.3.6.1.4.1.2011.6.139.1.2.5
Description.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwAcCountryCode 1.3.6.1.4.1.2011.6.139.1.2.6
Description.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

hwWlanApUsername 1.3.6.1.4.1.2011.6.139.1.2.8
Description: When set, need to together with password, and the username length is 4 to 31 characters.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(4..31)  

hwWlanApPassword 1.3.6.1.4.1.2011.6.139.1.2.9
Description: When set, need to together with username, and the password length is 8 to 32 characters which must contain at least one capital letter, one lowcase letter and one number.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(8..32)  

hwWlanUsernamePasswordApId 1.3.6.1.4.1.2011.6.139.1.2.10
Description: The node is useful only when get the username or password and must be set first and read with username or password. When get the username or password without the node ,it means get the gloable configuration from AC, otherwise, it means get the specified AP' username or password from AP. For when change the username or password,and not commit, the AC's configuration is diffrent with AP' real configuration. When specified the AP ID , and the AP is not in the normal state, return the username or password from AC's gloable configuration.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwWlanApLldpSwitch 1.3.6.1.4.1.2011.6.139.1.2.11
Description: Global AP LLDP switch.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

hwWlanAcAccessMaxStaNumber 1.3.6.1.4.1.2011.6.139.1.2.12
Description.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwWlanAcDtlsSwitch 1.3.6.1.4.1.2011.6.139.1.2.13
Description.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hwWlanAcDtlsPsk 1.3.6.1.4.1.2011.6.139.1.2.14
Description.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(1..32)  

hwWlanApLogManualBackupApId 1.3.6.1.4.1.2011.6.139.1.2.15
Description.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwWlanAcDtlsDefaultPskSwitch 1.3.6.1.4.1.2011.6.139.1.2.16
Description.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hwWlanWorkMode 1.3.6.1.4.1.2011.6.139.1.2.17
Description.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ac(1), ap(2)  

hwWlanIpv6Enable 1.3.6.1.4.1.2011.6.139.1.2.18
Description.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

hwWlanInterAcDtlsEncrpyt 1.3.6.1.4.1.2011.6.139.1.2.19
Description.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

hwWlanInterAcDtlsPsk 1.3.6.1.4.1.2011.6.139.1.2.20
Description.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(1..32)  

hwWlanStaIpv6Switch 1.3.6.1.4.1.2011.6.139.1.2.21
Whether to process IPv6 services of STAs.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

hwWlanAcSourceInterface 1.3.6.1.4.1.2011.6.139.1.3
OBJECT IDENTIFIER    

hwWlanAcSourceInterfaceValue 1.3.6.1.4.1.2011.6.139.1.3.1
the value of wlan ac source interface.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwWlanAcSourceInterfaceMethod 1.3.6.1.4.1.2011.6.139.1.3.2
operation method of wlan ac source interface.It can be set default(1): use default setting vlanif(2): use vlanif interface loopback(3): use loopback interface ipaddress(4):user ip address
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER default(1), vlanif(2), loopback(3), ipaddress(4)  

hwWlanAcSourceIPv4Address 1.3.6.1.4.1.2011.6.139.1.3.3
Description.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

hwWlanBatchQuery 1.3.6.1.4.1.2011.6.139.1.4
OBJECT IDENTIFIER    

hwWlanBatchQueryType 1.3.6.1.4.1.2011.6.139.1.4.1
Data type of Batch query. For example, apProfName(1) can be used to get ap-profile-name list. The batch query support two modes, the number mode and the ID list mode, binding the node hwWlanBatchRequestNum and hwWlanBatchStartCount means use the number mode, binding the node hwWlanBatchRequestIdList, hwWlanBatchRequestIdSize hwWlanBatchRequestIdNum means use the ID list mode.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER apProfName(1), apWhiteListMac(2), apWhiteListSn(3), apBlackListMac(4), apBlackListSn(5), apRegionId(6), apRegionIdModeName(7), apId(8), apIdState(9), apIdStateRegionName(10), unauthApIdMac(11), radioProfName(12), radioBalanceGroupName(13), uncontrolApIdBssidAuthApId(14), essNameSsid(15), wmmProfName(16), trafficProfName(17), secProfName(18), authMacStateType(19), clear(65535)  

hwWlanBatchRequestNum 1.3.6.1.4.1.2011.6.139.1.4.2
The request number of the batch query, it used in number mode. This node must be set in company with the node hwWlanBatchStartCount. For example, there are 6 ap-profiles(0 1 3 5 6 9) in the AC, Set hwWlanBatchQuery to apProfName(1), set hwWlanBatchRequestNum to 3, and set hwWlanBatchStartCount to 2, then get the node hwWlanBatchValueList and hwWlanBatchReturnNum, that means start from the 2nd ap-profile, get 3 ap-profile-names, the result in hwWlanBatchValueList are ap-profile(3 5 6 9).
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwWlanBatchStartCount 1.3.6.1.4.1.2011.6.139.1.4.3
The start count of the batch query, it used in number mode. This node must be set in company with the node hwWlanBatchRequestNum. For example, there are 6 ap-profiles(0 1 3 5 6 9) in the AC, Set hwWlanBatchQuery to apProfName(1), set hwWlanBatchRequestNum to 3, and set hwWlanBatchStartCount to 2, then get the node hwWlanBatchValueList and hwWlanBatchReturnNum, that means start from the 2nd ap-profile, get 3 ap-profile-names, the result in hwWlanBatchValueList are ap-profile(3 5 6 9).
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwWlanBatchRequestIdList 1.3.6.1.4.1.2011.6.139.1.4.4
The ID list of the data type, It used in ID list mode. This node must be set in company with the node hwWlanBatchRequestIdSize and hwWlanBatchRequestIdNum. For example, Ther are 6 apid(0 1 3 4 5 6) int the AC, set hwWlanBatchQuery to apIdStateRegionName(10), set hwWlanBatchRequestIdList to #0x00 0x01 0x00 0x02 0x00 0x03 (ap1 ap2 ap3), set hwWlanBatchRequestIdSize to 2(bytes), and set hwWlanBatchRequestIdNum to 3, then get the node hwWlanBatchValueList and hwWlanBatchReturnNum. The result in hwWlanBatchValueList are apids(1 2 3)
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..2048)  

hwWlanBatchRequestIdSize 1.3.6.1.4.1.2011.6.139.1.4.5
The length of a batch query ID element, it used in ID list mode. This node must be set in company with the node hwWlanBatchRequestIdList and hwWlanBatchRequestIdNum. For example, Ther are 6 apid(0 1 3 4 5 6) int the AC, set hwWlanBatchQuery to apIdStateRegionName(10), set hwWlanBatchRequestIdList to #0x00 0x01 0x00 0x02 0x00 0x03 (ap1 ap2 ap3), set hwWlanBatchRequestIdSize to 2(bytes), and set hwWlanBatchRequestIdNum to 3, then get the node hwWlanBatchValueList and hwWlanBatchReturnNum. The result in hwWlanBatchValueList are apids(1 2 3)
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwWlanBatchRequestIdNum 1.3.6.1.4.1.2011.6.139.1.4.6
The number of batch query by id, it used in ID list mode. This node must be set in company with the node hwWlanBatchRequestIdList and hwWlanBatchRequestIdSize. For example, Ther are 6 apid(0 1 3 4 5 6) int the AC, set hwWlanBatchQuery to apIdStateRegionName(10), set hwWlanBatchRequestIdList to #0x00 0x01 0x00 0x02 0x00 0x03 (ap1 ap2 ap3), set hwWlanBatchRequestIdSize to 2(bytes), and set hwWlanBatchRequestIdNum to 3, then get the node hwWlanBatchValueList and hwWlanBatchReturnNum. The result in hwWlanBatchValueList are apids(1 2 3)
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwWlanBatchValueList 1.3.6.1.4.1.2011.6.139.1.4.7
The returned value list. If the value ended by a string, each value is divided by '?', otherwise , each value will have a fixed length. This node must be get in company with the node hwWlanBatchReturnNum.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..6144)  

hwWlanBatchReturnNum 1.3.6.1.4.1.2011.6.139.1.4.8
The number of successful query. This node must be get in company with the node hwWlanBatchValueList.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwWlanBatchTotalNum 1.3.6.1.4.1.2011.6.139.1.4.9
Total number of current batch query. For example, There are 10 ap-Profiles in the AC, the value of this node will be 10.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwWlanCapwapConfig 1.3.6.1.4.1.2011.6.139.1.5
OBJECT IDENTIFIER    

hwWlanCapwapKeepAliveInterval 1.3.6.1.4.1.2011.6.139.1.5.1
The interval of maintain freshness of the CAPWAP channel, in seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwWlanCapwapKeepAliveTimes 1.3.6.1.4.1.2011.6.139.1.5.2
The times of maintain freshness of the CAPWAP channel before it timeout.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwWlanCapwapControlPriorityACToAP 1.3.6.1.4.1.2011.6.139.1.5.3
the ac's priority value of CAPWAP control packet,includ cos and tos, ranging between 0 and 7.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwWlanCapwapControlPriorityAPToAC 1.3.6.1.4.1.2011.6.139.1.5.4
the ap's priority value of CAPWAP control packet,includ tos, ranging between 0 and 7.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwWlanAcProtect 1.3.6.1.4.1.2011.6.139.1.6
OBJECT IDENTIFIER    

hwWlanAcProtectIpAddress 1.3.6.1.4.1.2011.6.139.1.6.1
IP address of the backup AC.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

hwWlanAcProtectPriority 1.3.6.1.4.1.2011.6.139.1.6.2
Dual-link hot backup priorities.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..7  

hwWlanAcProtectSwitch 1.3.6.1.4.1.2011.6.139.1.6.3
Dual-link hot backup switch.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hwWlanAcProtectRestoreSwitch 1.3.6.1.4.1.2011.6.139.1.6.4
Description.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hwUndoWlanAcProtectIpAddress 1.3.6.1.4.1.2011.6.139.1.6.5
Description.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwUndoWlanAcProtectPriority 1.3.6.1.4.1.2011.6.139.1.6.6
Description.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwWlanAcProtectIpv6Address 1.3.6.1.4.1.2011.6.139.1.6.7
Description.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..46)  

hwWlanConfigChannel 1.3.6.1.4.1.2011.6.139.1.7
OBJECT IDENTIFIER    

hwWlan24G20MconfigChannel 1.3.6.1.4.1.2011.6.139.1.7.1
Description.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

hwWlan24G40MPlusConfigChannel 1.3.6.1.4.1.2011.6.139.1.7.2
Description.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

hwWlan24G40MMinusConfigChannel 1.3.6.1.4.1.2011.6.139.1.7.3
Description.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

hwWlan5G20MConfigChannel 1.3.6.1.4.1.2011.6.139.1.7.4
Description.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

hwWlan5G40MPlusConfigChannel 1.3.6.1.4.1.2011.6.139.1.7.5
Description.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

hwWlan5G40MMinusConfigChannel 1.3.6.1.4.1.2011.6.139.1.7.6
Description.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

hwWlanConfigChannelApId 1.3.6.1.4.1.2011.6.139.1.7.7
Ap index, is used to identify AP uniquely.Query the configurable channel of the ap must contain apid otherwise query are global configurable channel.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwWlan24G80MConfigChannel 1.3.6.1.4.1.2011.6.139.1.7.8
Description.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

hwWlan5G80MConfigChannel 1.3.6.1.4.1.2011.6.139.1.7.9
Description.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

hwWlanStaLoadbalance 1.3.6.1.4.1.2011.6.139.1.8
OBJECT IDENTIFIER    

hwWlanStaLoadbalanceEnable 1.3.6.1.4.1.2011.6.139.1.8.1
Description.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwWlanStaLoadbalanceMode 1.3.6.1.4.1.2011.6.139.1.8.2
Description.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwWlanStaLoadbalanceSessionGap 1.3.6.1.4.1.2011.6.139.1.8.3
Description.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwWlanStaLoadbalanceTrafficGap 1.3.6.1.4.1.2011.6.139.1.8.4
Description.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwWlanStaLoadbalanceAssociateThreshold 1.3.6.1.4.1.2011.6.139.1.8.5
Description.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwWlanHsbConfig 1.3.6.1.4.1.2011.6.139.1.9
OBJECT IDENTIFIER    

hwWlanHsbServiceType 1.3.6.1.4.1.2011.6.139.1.9.1
The hsb service type can be one of the three values: 1, 2, 3 (1: disable(1) 2: hsbGroup(2) 3: hsbService(3)). The default value of this node is 1.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), hsbGroup(2), hsbService(3)  

hwWlanHsbGroupId 1.3.6.1.4.1.2011.6.139.1.9.2
The id of the hsb group used. When hsb service type is disabled, the value of this node is 0xFFFFFFFF.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

hwWlanHsbTunnelId 1.3.6.1.4.1.2011.6.139.1.9.3
The id of the hsb tunnel used. When hsb service type is disabled, the value of this node is 0xFFFFFFFF.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

hwWlanLocation 1.3.6.1.4.1.2011.6.139.1.10
OBJECT IDENTIFIER    

hwWlanLocationServerIP 1.3.6.1.4.1.2011.6.139.1.10.1
Description.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

hwWlanLocationServerPort 1.3.6.1.4.1.2011.6.139.1.10.2
Description.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwWlanLocationSourceIP 1.3.6.1.4.1.2011.6.139.1.10.3
Description.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

hwWlanLocationApReportToAC 1.3.6.1.4.1.2011.6.139.1.10.4
Description.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwWlanLocationApReportToServerIp 1.3.6.1.4.1.2011.6.139.1.10.5
Description.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

hwWlanLocationApReportToUdpPort 1.3.6.1.4.1.2011.6.139.1.10.6
Description.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwWlanLocationApReportToIpv6Addr 1.3.6.1.4.1.2011.6.139.1.10.7
Description.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..46)  

hwWlanLocationAcReportToIpv6Addr 1.3.6.1.4.1.2011.6.139.1.10.8
Description.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..46)  

hwWlanSpectrumAnalysis 1.3.6.1.4.1.2011.6.139.1.11
OBJECT IDENTIFIER    

hwWlanSpectrumAnalysisServerIP 1.3.6.1.4.1.2011.6.139.1.11.1
Description.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

hwWlanSpectrumAnalysisServerPort 1.3.6.1.4.1.2011.6.139.1.11.2
Description.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwWlanNonWifiDeviceAgeTime 1.3.6.1.4.1.2011.6.139.1.11.3
Description.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwWlanSpectrogramServerIP 1.3.6.1.4.1.2011.6.139.1.11.4
Description.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

hwWlanSpectrogramServerPort 1.3.6.1.4.1.2011.6.139.1.11.5
Description.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwWlanSpectrumAnalysisServerIPv6Addr 1.3.6.1.4.1.2011.6.139.1.11.6
Description.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..46)  

hwWlanSpectrogramServerIPv6Addr 1.3.6.1.4.1.2011.6.139.1.11.7
Description.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..46)  

hwWlanSysManagementObjects 1.3.6.1.4.1.2011.6.139.1.12
OBJECT IDENTIFIER    

hwWlanLBSConfig 1.3.6.1.4.1.2011.6.139.1.12.1
OBJECT IDENTIFIER    

hwWlanLBSAeServerPort 1.3.6.1.4.1.2011.6.139.1.12.1.1
Description.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwWlanLBSAeApReportMode 1.3.6.1.4.1.2011.6.139.1.12.1.2
Description.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER off(1), toAc(2), toServer(3)  

hwWlanLBSAeApReportPort 1.3.6.1.4.1.2011.6.139.1.12.1.3
Description.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwWlanLBSEkServerIp 1.3.6.1.4.1.2011.6.139.1.12.1.4
Description.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

hwWlanLBSEkServerPort 1.3.6.1.4.1.2011.6.139.1.12.1.5
Description.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwWlanLBSEkApReportMode 1.3.6.1.4.1.2011.6.139.1.12.1.6
Description.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER off(1), toAc(2), toServer(3)  

hwWlanLBSEkApReportIp 1.3.6.1.4.1.2011.6.139.1.12.1.7
Description.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

hwWlanLBSEkApReportPort 1.3.6.1.4.1.2011.6.139.1.12.1.8
Description.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwWlanLBSSourceIp 1.3.6.1.4.1.2011.6.139.1.12.1.9
Description.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

hwWlanLBSAeCompoundTime 1.3.6.1.4.1.2011.6.139.1.12.1.10
Compound Time of AeroScout Tag Message
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwWlanLBSEkServerIpv6Addr 1.3.6.1.4.1.2011.6.139.1.12.1.11
Description.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..46)  

hwWlanLBSEkApReportIpv6Addr 1.3.6.1.4.1.2011.6.139.1.12.1.12
Description.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..46)  

hwWlanLBSSourceIpv6Addr 1.3.6.1.4.1.2011.6.139.1.12.1.13
Description.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..46)  

hwInterAcManagement 1.3.6.1.4.1.2011.6.139.1.13
OBJECT IDENTIFIER    

hwMasterControllerSwitch 1.3.6.1.4.1.2011.6.139.1.13.1
Description.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

hwConnectMasterControllerSwitch 1.3.6.1.4.1.2011.6.139.1.13.2
Description.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disconnect(1), connect(2)  

hwConnectMasterControllerIPv4Address 1.3.6.1.4.1.2011.6.139.1.13.3
Description.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

hwConnectMasterControllerIPv6Address 1.3.6.1.4.1.2011.6.139.1.13.4
Description.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

hwWlanSysManagementConformance 1.3.6.1.4.1.2011.6.139.1.14
OBJECT IDENTIFIER    

hwWlanSysManagementCompliances 1.3.6.1.4.1.2011.6.139.1.14.1
OBJECT IDENTIFIER    

hwWlanSysManagementCompliance 1.3.6.1.4.1.2011.6.139.1.14.1.1
Description.
Status: current Access: read-write
MODULE-COMPLIANCE    

hwWlanSysManagementObjectGroups 1.3.6.1.4.1.2011.6.139.1.14.2
OBJECT IDENTIFIER    

hwWlanTrapRestrainGroup 1.3.6.1.4.1.2011.6.139.1.14.2.1
Description.
Status: current Access: read-write
OBJECT-GROUP    

hwWlanSysParaGroup 1.3.6.1.4.1.2011.6.139.1.14.2.2
Description.
Status: current Access: read-write
OBJECT-GROUP    

hwWlanAcSourceInterfaceGroup 1.3.6.1.4.1.2011.6.139.1.14.2.3
Description.
Status: current Access: read-write
OBJECT-GROUP    

hwWlanBatchQueryGroup 1.3.6.1.4.1.2011.6.139.1.14.2.4
Description.
Status: current Access: read-write
OBJECT-GROUP    

hwWlanCapwapConfigGroup 1.3.6.1.4.1.2011.6.139.1.14.2.5
Description.
Status: current Access: read-write
OBJECT-GROUP    

hwWlanAcProtectGroup 1.3.6.1.4.1.2011.6.139.1.14.2.6
Description.
Status: current Access: read-write
OBJECT-GROUP    

hwWlanConfigChannelGroup 1.3.6.1.4.1.2011.6.139.1.14.2.7
Description.
Status: current Access: read-write
OBJECT-GROUP    

hwWlanStaLoadbalanceGroup 1.3.6.1.4.1.2011.6.139.1.14.2.8
Description.
Status: current Access: read-write
OBJECT-GROUP    

hwWlanHsbConfigGroup 1.3.6.1.4.1.2011.6.139.1.14.2.9
Description.
Status: current Access: read-write
OBJECT-GROUP    

hwWlanLocationGroup 1.3.6.1.4.1.2011.6.139.1.14.2.10
Description.
Status: current Access: read-write
OBJECT-GROUP    

hwWlanSpectrumAnalysisGroup 1.3.6.1.4.1.2011.6.139.1.14.2.11
Description.
Status: current Access: read-write
OBJECT-GROUP    

hwWlanLBSConfigGroup 1.3.6.1.4.1.2011.6.139.1.14.2.12
Description.
Status: current Access: read-write
OBJECT-GROUP    

hwInterAcManagementGroup 1.3.6.1.4.1.2011.6.139.1.14.2.13
Description.
Status: current Access: read-write
OBJECT-GROUP