HUAWEI-MPLSLDP-MIB

File: HUAWEI-MPLSLDP-MIB.mib (97054 bytes)

Imported modules

HUAWEI-MIB IF-MIB INET-ADDRESS-MIB
P-BRIDGE-MIB MPLS-TC-STD-MIB SNMPv2-CONF
SNMPv2-TC SNMPv2-SMI

Imported symbols

hwDatacomm InterfaceIndex InterfaceIndexOrZero
InetAddress EnabledStatus MplsLdpIdentifier
MplsLsrIdentifier OBJECT-GROUP MODULE-COMPLIANCE
NOTIFICATION-GROUP DisplayString RowStatus
TimeTicks Integer32 Unsigned32
IpAddress Counter32 OBJECT-TYPE
MODULE-IDENTITY NOTIFICATION-TYPE

Defined Types

HwMplsLdpSessionEntry  
SEQUENCE    
  hwMplsLdpSessionPeerLsrId MplsLdpIdentifier
  hwMplsLdpSessionIfIndex Integer32
  hwMplsLdpSessionDownReason INTEGER
  hwMplsLdpSessionAge TimeTicks

HwMplsLdpSessionStateEntry  
SEQUENCE    
  hwMplsLdpSessionPeerId MplsLdpIdentifier
  hwMplsLdpSessionLsrId MplsLdpIdentifier
  hwMplsLdpSessionTcpConnectionState OCTET STRING
  hwMplsLdpSessionState OCTET STRING
  hwMplsLdpSessionRole OCTET STRING
  hwMplsLdpSessionFtFlag OCTET STRING
  hwMplsLdpSessionMd5Flag OCTET STRING
  hwMplsLdpSessionReconnectTimer Unsigned32
  hwMplsLdpSessionRecoveryTimer Unsigned32
  hwMplsLdpSessionKeepAliveTimer Unsigned32
  hwMplsLdpSessionKeepAliveMsgReceived Unsigned32
  hwMplsLdpSessionKeepAliveMsgSent Unsigned32
  hwMplsLdpSessionLabelAdvMode OCTET STRING
  hwMplsLdpSessionLocalLabelResourceStatus OCTET STRING
  hwMplsLdpSessionPeerLabelResourceStatus OCTET STRING
  hwMplsLdpSessionAgeStatus TimeTicks

HwLdpVpnEntry  
SEQUENCE    
  hwLdpVpnInstanceId Unsigned32
  hwLdpVpnLsrId IpAddress
  hwLdpVpnSplitHorizonAll EnabledStatus
  hwLdpVpnReset INTEGER
  hwMplsVpnFrrLspTrigger INTEGER
  hwMplsVpnFrrLspTriggerIpPrefix OCTET STRING
  hwLdpVpnGracefulDeleteCapability EnabledStatus
  hwLdpVpnGracefulDeleteTimer Integer32
  hwLdpVpnRowStatus RowStatus

HwLdpRemoteEntityEntry  
SEQUENCE    
  hwLdpRemoteName DisplayString
  hwLdpRemoteIp IpAddress
  hwLdpRemotePwe3 EnabledStatus
  hwLdpRemoteKeepaliveTimer Integer32
  hwLdpRemoteHelloTimer Integer32
  hwLdpRemoteKeepaliveSendTimer Integer32
  hwLdpRemoteHelloSendTimer Integer32
  hwLdpRemoteIgpSyncTimer Integer32
  hwLdpRemoteIpAutoDoDRequest EnabledStatus
  hwLdpRemoteIpAutoDoDRequestBlock EnabledStatus
  hwLdpRemoteLabelAdvertisementMode INTEGER
  hwLdpRemoteLocalLsrIdIfIndex InterfaceIndexOrZero
  hwLdpRemoteRowStatus RowStatus

HwLdpPeerEntry  
SEQUENCE    
  hwLdpPeerLsrId IpAddress
  hwLdpPeerMd5Type INTEGER
  hwLdpPeerMd5Password OCTET STRING
  hwLdpPeerGtsmHops Integer32
  hwLdpPeerSplitHorizon EnabledStatus
  hwLdpPeerReset INTEGER
  hwLdpPeerKeychainName OCTET STRING
  hwLdpPeerOutBoundPolicyRange INTEGER
  hwLdpPeerOutBoundPolicyFecIpPrefix OCTET STRING
  hwLdpPeerOutBoundPolicyBgpRange INTEGER
  hwLdpPeerOutBoundPolicyBgpIpPrefix OCTET STRING
  hwLdpPeerInBoundPolicyRange INTEGER
  hwLdpPeerInBoundPolicyFecIpPrefix OCTET STRING
  hwLdpPeerRowStatus RowStatus

HwLdpVpnPeerEntry  
SEQUENCE    
  hwLdpVpnPeerLsrId IpAddress
  hwLdpVpnPeerMd5Type INTEGER
  hwLdpVpnPeerMd5Password OCTET STRING
  hwLdpVpnPeerSplitHorizon EnabledStatus
  hwLdpVpnPeerReset INTEGER
  hwLdpVpnPeerKeychainName OCTET STRING
  hwLdpVpnPeerRowStatus RowStatus

HwLdpInterfaceEntry  
SEQUENCE    
  hwLdpInterfaceIndex InterfaceIndex
  hwLdpStaticFrrProtectTimer Integer32
  hwLdpKeepAliveTimer Integer32
  hwLdpIgpSyncTimer Integer32
  hwLdpHelloTimer Integer32
  hwLdpTransportAddressIfIndex InterfaceIndexOrZero
  hwLdpKeepAliveSendTimer Integer32
  hwLdpHelloSendTimer Integer32
  hwLdpInterfaceLabelAdvertisementMode INTEGER
  hwLdpInterfaceLocalLsrIdIfIndex InterfaceIndexOrZero
  hwLdpInterfaceRowStatus RowStatus

HwLdpPeerGroupEntry  
SEQUENCE    
  hwLdpPeerGroupName OCTET STRING
  hwLdpPeerGroupOutBoundRange INTEGER
  hwLdpPeerGroupOutBoundFecIpPrefix OCTET STRING
  hwLdpPeerGroupOutBoundBgpRange INTEGER
  hwLdpPeerGroupOutBoundBgpIpPrefix OCTET STRING
  hwLdpPeerGroupInBoundRange INTEGER
  hwLdpPeerGroupInBoundIpPrefix OCTET STRING
  hwLdpPeerGroupRowStatus RowStatus

Defined Values

hwMplsLdp 1.1.4.1.2011.5.25.143
This MIB contains private managed object and notification trap definitions for MPLS LDP.
MODULE-IDENTITY    

hwMplsLdpInfo 1.1.4.1.2011.5.25.143.1
OBJECT IDENTIFIER    

hwMplsLdpProcessName 1.1.4.1.2011.5.25.143.1.1
This object indicates the process name of LDP running on the router. By default, the value is LDP.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

hwMplsLdpLspFec 1.1.4.1.2011.5.25.143.1.2
This object indicates the destination address of an LSP. The value is either a destination IP address or a prefix of an IP address.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  InetAddress  

hwMplsLdpLspInLabel 1.1.4.1.2011.5.25.143.1.3
This object indicates that labels are pushed into all the packets for direct MPLS forwarding.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Counter32  

hwMplsLdpLspOutLabel 1.1.4.1.2011.5.25.143.1.4
This object indicates that all the packets swap labels for MPLS forwarding.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Counter32  

hwMplsLdpLspOutIfIndex 1.1.4.1.2011.5.25.143.1.5
The value of this object identifies the index of the outgoing interface of the LSP.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  InterfaceIndex  

hwMplsLdpLspDownReason 1.1.4.1.2011.5.25.143.1.6
This object indicates the cause that the LSP becomes Down. Options: 1. routeDelete(1) -indicates that a route has been deleted. 2. lspmNotify(2) -indicates that LSPM notify. 3. canNotRecoveryFromGr(3) -indicates that the recovery from GR was failed. 4. recvReleaseMsg(4) -indicates that the release message was received. 5. recvWithdrawMsg(5) -indicates that the withdraw message was received. 6. upStreamLost(6) -indicates that the upstream route was lost. 7. downStreamLost(7) -indicates that the downstream route was lost. 8. otherReason(8) -indicates that another cause was involved.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER routeDelete(1), lspmNotify(2), canNotRecoveryFromGr(3), recvReleaseMsg(4), recvWithdrawMsg(5), upStreamLost(6), downStreamLost(7), otherReason(8)  

hwMplsLdpSessionTable 1.1.4.1.2011.5.25.143.1.7
This object is used to display the session parameters and session age. The index of this table is hwMplsLdpSessionPeerLsrId.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwMplsLdpSessionEntry

hwMplsLdpSessionEntry 1.1.4.1.2011.5.25.143.1.7.1
This object is used to display the session parameters and session age. The index of this entry is hwMplsLdpSessionPeerLsrId.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwMplsLdpSessionEntry  

hwMplsLdpSessionPeerLsrId 1.1.4.1.2011.5.25.143.1.7.1.1
This object indicates the LSR ID of the peer in a session.
Status: current Access: not-accessible
OBJECT-TYPE    
  MplsLdpIdentifier  

hwMplsLdpSessionIfIndex 1.1.4.1.2011.5.25.143.1.7.1.2
This object indicates the index of the interface on which the session is established.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

hwMplsLdpSessionDownReason 1.1.4.1.2011.5.25.143.1.7.1.3
This object indicates the cause that the session becomes Down. Options: 1. sessionUp(0) -indicates that the session was Up. 2. helloHoldTimerExp(1) -indicates that the Hello hold timer expired. 3. ssnHoldTimerExp(2) -indicates that the session hold timer expired. 4. resetMplsLdp(3) -indicates MPLS LDP was reset. 5. undoMplsLdp(4) -indicates that MPLS LDP was disabled. 6. undoMpls(5) -indicates that MPLS was disabled. 7. undoMplsLdpRemotePeer(6) -indicates that the remote peer was deleted. 8. modifyGRConfig(7) -indicates that GR capability was modified. 9. modifyGRTimer(8) -indicates that the GR timer was modified. 10. modifyKeepaliveTimer(9) -indicates that the keepalive timer was modified. 11. modifyMD5Config(10) -indicates that MD5 was configured. 12. ssnRoleSwitch(11) -indicates that the session role was switched. 13. modifyMTUConfig(12) -indicates that the MTU was modified. 14. modifyTransportAddress(13) -indicates that the transport address was modified. 15. modifyLDPLsrID(14) -indicates that the LDP LSR ID was modified. 16. recvNotification(15) -indicates that the notification message was received. 17. transportAddressNotMatch(16) -indicates that the transport address was not matched. 18. protocolGR(17) -indicates that the protocol GR was in processing. 19. ifStatusChanged(18) -indicates that the interface status was changed. 20. tcpDown(19) -indicates that TCP was Down. 21. otherReason(20) -indicates that another cause was involved. 22. sentNotification(21) -indicates that the notification was sent. 23. canntBuildSessionRelation(22) -indicates that the session relation cannot be built. 24. receiveErrorMessageFromPeer(23) -indicates that error message from peer was received. 25. receiveSocketError(24) -indicates that error pakcet from socket was received. 26. sessionDelete(25) -indicates that the session was deleted. 27. modifyCapabilityAnnouncementConfig(26) -indicates that the capability-announcement was modified. 28. modifyLocalLsrID(27) -indicates that the Local LSR ID was modified. 29. modifyP2MP(28) -indicates that the mLDP P2MP was modified. 30. modifyMP2MP(29) -indicates that the mLDP MP2MP was modified. 31. sessionProtectTimerExp(30) -indicates that the session protection timer expired.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER sessionUp(0), helloHoldTimerExp(1), ssnHoldTimerExp(2), resetMplsLdp(3), undoMplsLdp(4), undoMpls(5), undoMplsLdpRemotePeer(6), modifyGRConfig(7), modifyGRTimer(8), modifyKeepaliveTimer(9), modifyMD5Config(10), ssnRoleSwitch(11), modifyMTUConfig(12), modifyTransportAddress(13), modifyLDPLsrID(14), recvNotification(15), transportAddressNotMatch(16), protocolGR(17), ifStatusChanged(18), tcpDown(19), otherReason(20), sentNotification(21), canntBuildSessionRelation(22), receiveErrorMessageFromPeer(23), receiveSocketError(24), sessionDelete(25), modifyCapabilityAnnouncementConfig(26), modifyLocalLsrID(27), modifyP2MP(28), modifyMP2MP(29), sessionProtectTimerExp(30)  

hwMplsLdpSessionAge 1.1.4.1.2011.5.25.143.1.7.1.4
This object indicates the duration since the session is set up.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

hwMplsLdpSessionStateTable 1.1.4.1.2011.5.25.143.1.8
This object is used to display the detailed state parameters of the session. The index of this table is hwMplsLdpSessionPeerId.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwMplsLdpSessionStateEntry

hwMplsLdpSessionStateEntry 1.1.4.1.2011.5.25.143.1.8.1
This object is used to display the detailed state parameters of the session. The index of this entry is hwMplsLdpSessionPeerId.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwMplsLdpSessionStateEntry  

hwMplsLdpSessionPeerId 1.1.4.1.2011.5.25.143.1.8.1.1
This object indicates the LSR ID of the LDP peer to which the session is connected.
Status: current Access: not-accessible
OBJECT-TYPE    
  MplsLdpIdentifier  

hwMplsLdpSessionLsrId 1.1.4.1.2011.5.25.143.1.8.1.2
This object indicates the ID of the local LSR.
Status: current Access: read-only
OBJECT-TYPE    
  MplsLdpIdentifier  

hwMplsLdpSessionTcpConnectionState 1.1.4.1.2011.5.25.143.1.8.1.3
This object indicates the TCP link status of the session.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

hwMplsLdpSessionState 1.1.4.1.2011.5.25.143.1.8.1.4
This object indicates the current status of the session.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

hwMplsLdpSessionRole 1.1.4.1.2011.5.25.143.1.8.1.5
This object indicates the session roles.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

hwMplsLdpSessionFtFlag 1.1.4.1.2011.5.25.143.1.8.1.6
This object indicates whether the FT of the session is enabled.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

hwMplsLdpSessionMd5Flag 1.1.4.1.2011.5.25.143.1.8.1.7
This object indicates whether the MD5 is enabled for the peer.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

hwMplsLdpSessionReconnectTimer 1.1.4.1.2011.5.25.143.1.8.1.8
This object indicates the value of the GR reconnection timer after the negotiation. Unit: seconds
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwMplsLdpSessionRecoveryTimer 1.1.4.1.2011.5.25.143.1.8.1.9
This object indicates the value of the GR recovery timer after the negotiation. Unit: seconds
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwMplsLdpSessionKeepAliveTimer 1.1.4.1.2011.5.25.143.1.8.1.10
This object indicates the value of the KeepAlive timer after the negotiation. Unit: seconds
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwMplsLdpSessionKeepAliveMsgReceived 1.1.4.1.2011.5.25.143.1.8.1.11
This object indicates the number of the KeepAlive messages that the session obtains.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwMplsLdpSessionKeepAliveMsgSent 1.1.4.1.2011.5.25.143.1.8.1.12
This object indicates the number of the KeepAlive messages that the session sends.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwMplsLdpSessionLabelAdvMode 1.1.4.1.2011.5.25.143.1.8.1.13
This object indicates the label distribution mode of the session.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

hwMplsLdpSessionLocalLabelResourceStatus 1.1.4.1.2011.5.25.143.1.8.1.14
This object indicates the status of the local label resources of the session.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

hwMplsLdpSessionPeerLabelResourceStatus 1.1.4.1.2011.5.25.143.1.8.1.15
This object indicates the status of the label resources of the LDP peer.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

hwMplsLdpSessionAgeStatus 1.1.4.1.2011.5.25.143.1.8.1.16
This object indicates the existence time of the session.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

hwLdpCapabilityConfig 1.1.4.1.2011.5.25.143.1.9
This object indicates the global configuration or deletion of the LDP capability. Before enabling LDP capability, ensure that the MPLS capability is enabled globally.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

hwLdpLsrId 1.1.4.1.2011.5.25.143.1.10
This object indicates the way to change the LDP LSR ID. The default LDP LSR ID has the same value as the MPLS LSR ID. It is recommended not to change the LDP LSR ID unless necessary.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

hwLdpPropagateIpPrefix 1.1.4.1.2011.5.25.143.1.11
This object indicates the configuration or deletion of the transit policy for the LDP. The object has a valid length ranging from 1 to 169 characters. The length 0 characters shows that the transit policy is deleted.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

hwLdpGlobalRemotePwe3 1.1.4.1.2011.5.25.143.1.12
This object indicates the configuration or deletion of the policy for the LDP remote session. When the object is enabled, it is forbidden to send mapping message to the remote peer. By default, the policy is disabled, which means that there is no limitation to send mapping message to the remote peer.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

hwLdpMtuSignaling 1.1.4.1.2011.5.25.143.1.13
This object indicates the configuration or deletion of the MTU signaling function. By default, the MTU signaling function is enabled, and the MTU TLV type in the LDP message is 0x900.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

hwLdpMtuApplyTlv 1.1.4.1.2011.5.25.143.1.14
This object conflicts with the object hwLdpMtuSignaling. If the object is enabled, it indicates that the MTU TLV type in the LDP message is 0x601 according to the RFC 3988.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

hwLdpGrCapabilityConfig 1.1.4.1.2011.5.25.143.1.15
This object indicates the configuration or deletion of the LDP GR capability.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

hwLdpGrNeighborLivenessTimer 1.1.4.1.2011.5.25.143.1.16
This object indicates the way to configure the value of GR neighbor life timer. When the status of hwLdpGrCapabilityConfig is enabled, the default value returned by the object is valid. Unit: seconds
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwLdpGrReconnectTimer 1.1.4.1.2011.5.25.143.1.17
This object indicates the way to configure the value of GR reconnect timer. When the status of hwLdpGrCapabilityConfig is enabled, the default value returned by the object is valid. Unit: seconds
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwLdpGrRecoveryTimer 1.1.4.1.2011.5.25.143.1.18
This object indicates the way to configure the value of GR recovery timer. When the status of hwLdpGrCapabilityConfig is enabled, the default value returned by the object is valid. Unit: seconds
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hwMplsLspTrigger 1.1.4.1.2011.5.25.143.1.19
This object indicates the way to configure the LDP policy for the ingress LSP and egress LSP. Options: 1. all(1) -indicates that all FECs are triggered for the IGP. 2. none(2) -indicates that no FEC is triggered for the IGP. 3. host(3) -indicates that the host FEC is triggered for the IGP. 4. ipprefix(4) -indicates that the ip-prefix list is triggered for the IGP. If the object is set as ipprefix, the value of hwMplsLspTriggerIpPrefix must be set together. Default: host
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER all(1), none(2), host(3), ipprefix(4)  

hwMplsLspTriggerIpPrefix 1.1.4.1.2011.5.25.143.1.20
This object indicates the IP prefix when configuring the LDP policy for the ingress LSP and egress LSP. The object has a valid length ranging from 1 to 169 characters. If the object is set with a value, the value of hwMplsLspTrigger must be set as ipprefix.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

hwMplsLspTriggerBgpRoute 1.1.4.1.2011.5.25.143.1.21
This object indicates the policy of triggering the BGP route to create the LDP LSP. Default: disabled
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

hwMplsLspTriggerBgpRouteIpPrefix 1.1.4.1.2011.5.25.143.1.22
This object indicates the IP prefix when triggering the BGP route to create the LDP LSP. The object has a valid length ranging from 1 to 169 characters.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

hwLdpReset 1.1.4.1.2011.5.25.143.1.23
This object indicates the reset of the LDP protocol. Options: 1. reset(1) -indicates the reset of the LDP protocol. 2. resetall(2) -indicates the reset of all LDP instances. 3. ready(3) -indicates that it is ready to reset LDP. This value cannot be set.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER reset(1), resetall(2), ready(3)  

hwLdpOutBoundSplitHorizonAll 1.1.4.1.2011.5.25.143.1.24
This object indicates the way to set the flag of global split horizon. Default: disabled
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

hwLdpDeleteGtsmAll 1.1.4.1.2011.5.25.143.1.25
This object indicates the deletion of the global GTSM configurations. Options: 1. delete(1) -indicates that global GTSM configurations are to be deleted. 2. ready(2) -indicates that it is ready to delete global GTSM configurations.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER delete(1), ready(2)  

hwMplsFrrLspTrigger 1.1.4.1.2011.5.25.143.1.26
This object indicates the way to configure the LDP policy of global instance for LDP Auto FRR. Options: 1. all(1) -indicates that all FECs are triggered for the IGP. 2. none(2) -indicates that no FEC is triggered for the IGP. 3. host(3) -indicates that the host FEC is triggered for the IGP. 4. ipprefix(4) -indicates that the ip-prefix list is triggered for the IGP. If the object is set as ipprefix, the value of hwMplsFrrLspTriggerIpPrefix must be set together. Default: host
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER all(1), none(2), host(3), ipPrefix(4)  

hwMplsFrrLspTriggerIpPrefix 1.1.4.1.2011.5.25.143.1.27
This object indicates the IP prefix when configuring LDP Auto FRR for the public network instance. The object has a valid length ranging from 1 to 169 characters. If the object is set with a value, the value of hwMplsFrrLspTrigger must be set as ipprefix.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

hwLdpBackOffTimerInit 1.1.4.1.2011.5.25.143.1.28
This object indicates the initial value of backoff timer. Default: 15 Unit: seconds
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 5..2147483  

hwLdpBackOffTimerMax 1.1.4.1.2011.5.25.143.1.29
This object indicates the maximum value of backoff timer. Default: 120 Unit: seconds
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 5..2147483  

hwLdpLongestMatch 1.1.4.1.2011.5.25.143.1.30
This object indicates that the LDP is enabled with the function of searching for routes according to the longest match rule to establish LSPs. Default: disabled
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

hwLdpRemotePeerAutoDodRequest 1.1.4.1.2011.5.25.143.1.37
The value of this object identifies whether the remote peer is globally enabled with the capability of automatically sending a DoD request.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

hwLdpCapabilityAnnouncementConfig 1.1.4.1.2011.5.25.143.1.38
The value of this object identifies whether LDP has Capability-Announcement ability.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

hwLdpVpnTable 1.1.4.1.2011.5.25.143.1.50
This object is used to configure or delete the LDP multi-instance. The index of this table is hwLdpVpnInstanceId. Make sure the relevant VPN instance is already created.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwLdpVpnEntry

hwLdpVpnEntry 1.1.4.1.2011.5.25.143.1.50.1
This object is used to configure or delete the LDP multi-instance. The index of this entry is hwLdpVpnInstanceId. Make sure the relevant VPN instance is already created.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwLdpVpnEntry  

hwLdpVpnInstanceId 1.1.4.1.2011.5.25.143.1.50.1.1
This object indicates the ID of the VPN instance. You can find the correct VPN instance ID based on hwL3vpnVrfIndex of hwL3vpnStatisticsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

hwLdpVpnLsrId 1.1.4.1.2011.5.25.143.1.50.1.11
This object indicates the way to configure the LDP LSR ID. If the value of the LDP LSR ID is the same as the value of the MPLS LSR ID, the LDP LSR ID is deleted. It is recommended not to change the LDP LSR ID unless necessary.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

hwLdpVpnSplitHorizonAll 1.1.4.1.2011.5.25.143.1.50.1.12
This object indicates the way to set the flag of split horizon for all LDP VPN peers. Default: disabled
Status: current Access: read-create
OBJECT-TYPE    
  EnabledStatus  

hwLdpVpnReset 1.1.4.1.2011.5.25.143.1.50.1.13
This object indicates the reset of the LDP multi-instance corresponding to the VPN. Options: 1.reset(1) -indicates that the LDP multi-instance will be reset. 2.ready(2) -indicates that it is ready to reset ldp multi-instance. This value cannot be set.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER reset(1), ready(2)  

hwMplsVpnFrrLspTrigger 1.1.4.1.2011.5.25.143.1.50.1.14
This object indicates the way to configure the LDP policy of vpn instance for LDP Auto FRR. Options: 1. all(1) -indicates that all FECs are triggered for the IGP. 2. none(2) -indicates that no FEC is triggered for the IGP. 3. host(3) -indicates that the host FEC is triggered for the IGP. 4. ipprefix(4) -indicates that the ip-prefix list is triggered for the IGP. If the object is set as ipprefix, the value of hwMplsVpnFrrLspTriggerIpPrefix must be set together.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER all(1), none(2), host(3), ipPrefix(4)  

hwMplsVpnFrrLspTriggerIpPrefix 1.1.4.1.2011.5.25.143.1.50.1.15
This object indicates the IP prefix when configuring the LDP policy of vpn instance for LDP Auto FRR. The object has a valid length ranging from 1 to 169 characters. If the object is set with a value, the value of hwMplsVpnFrrLspTrigger must be set as ipprefix.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

hwLdpVpnGracefulDeleteCapability 1.1.4.1.2011.5.25.143.1.50.1.16
This object indicates whether the LDP graceful-delete capability is enabled for a VPN instance.
Status: current Access: read-create
OBJECT-TYPE    
  EnabledStatus  

hwLdpVpnGracefulDeleteTimer 1.1.4.1.2011.5.25.143.1.50.1.17
The value of this object identifies the value of a graceful-delete timer for a VPN instance. When the status of hwLdpVpnGracefulDeleteCapability is enabled, the default value returned by the object is valid. Default: 5 Unit: seconds
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..65535  

hwLdpVpnRowStatus 1.1.4.1.2011.5.25.143.1.50.1.51
This object indicates whether one entry of hwLdpVpnTable is created or destroyed. The value of this object can be CreatAndGo or Destroy. When the value of the object is set as CreatAndGo, and the entry is correctly created, the status of the object will change into active.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hwLdpRemoteEntityTable 1.1.4.1.2011.5.25.143.1.51
This object is used to configure or delete the LDP remote peer. The index of this table is hwLdpRemoteName.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwLdpRemoteEntityEntry

hwLdpRemoteEntityEntry 1.1.4.1.2011.5.25.143.1.51.1
This object is used to configure or delete the LDP remote peer. The index of this entry is hwLdpRemoteName.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwLdpRemoteEntityEntry  

hwLdpRemoteName 1.1.4.1.2011.5.25.143.1.51.1.1
This object indicates the name of the LDP remote peer. Range: 1-32 characters
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString  

hwLdpRemoteIp 1.1.4.1.2011.5.25.143.1.51.1.11
This object indicates the configuration of the remote peer LSR ID. If being set, the ID cannot be modified. To modify the ID, delete the original ID and create a new one. If the ID is set as 0.0.0.0, it indicates that the ID is deleted.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

hwLdpRemotePwe3 1.1.4.1.2011.5.25.143.1.51.1.12
This object indicates the configuration or deletion of the policy for the remote LDP session. When the object is enabled, it is forbidden to send the mapping message to the remote peer. Default: disabled
Status: current Access: read-create
OBJECT-TYPE    
  EnabledStatus  

hwLdpRemoteKeepaliveTimer 1.1.4.1.2011.5.25.143.1.51.1.13
This object indicates the value of LDP Keepalive timer. Default: 45 Unit: seconds
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 30..65535  

hwLdpRemoteHelloTimer 1.1.4.1.2011.5.25.143.1.51.1.14
This object indicates the value of LDP Hello hold timer. Default: 45 Unit: seconds
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 3..65535  

hwLdpRemoteKeepaliveSendTimer 1.1.4.1.2011.5.25.143.1.51.1.15
This object indicates the value of LDP Keepalive send timer. By default, the value of the timer is 0, configuration does not take effect. Default: 0 Unit: seconds
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

hwLdpRemoteHelloSendTimer 1.1.4.1.2011.5.25.143.1.51.1.16
This object indicates the value of LDP Hello send timer. By default, the value of the timer is 0, configuration does not take effect. Default: 0 Unit: seconds
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

hwLdpRemoteIgpSyncTimer 1.1.4.1.2011.5.25.143.1.51.1.17
This object indicates the value of IGP-Sync timer. Default: 10 Unit: seconds
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

hwLdpRemoteIpAutoDoDRequest 1.1.4.1.2011.5.25.143.1.51.1.18
This object identifies whether the remote peer is enabled with the capability of automatically sending a DoD request. Default: disabled
Status: current Access: read-create
OBJECT-TYPE    
  EnabledStatus  

hwLdpRemoteIpAutoDoDRequestBlock 1.1.4.1.2011.5.25.143.1.51.1.19
This object indicates whether the remote ip auto dod request function blocked. Default: disabled
Status: current Access: read-create
OBJECT-TYPE    
  EnabledStatus  

hwLdpRemoteLabelAdvertisementMode 1.1.4.1.2011.5.25.143.1.51.1.20
This object indicates the label distribution mode. Options: 1. dod(1) -indicates that the label distribution mode is dod. 2. du(2) -indicates that the label distribution mode is du. Default: du
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER dod(1), du(2)  

hwLdpRemoteLocalLsrIdIfIndex 1.1.4.1.2011.5.25.143.1.51.1.21
This object indicates the way to specify the interface that the local LDP LSR-ID based on remote entity is assigned to. Value: 0..2147483647 The default value of the object is the interface that the global LDP LSR ID is assigned to. If the global LDP LSR ID is not assigned to any interface, then the value of the object is 0. If set 0, the value of the object will be the default value.
Status: current Access: read-create
OBJECT-TYPE    
  InterfaceIndexOrZero  

hwLdpRemoteRowStatus 1.1.4.1.2011.5.25.143.1.51.1.51
This object indicates whether one entry of hwLdpRemoteEntityTable is created or destroyed. The value of this object can be CreatAndGo or Destroy. When the value of the object is set as CreatAndGo, and the entry is correctly created, the status of the object will change into active.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hwLdpPeerTable 1.1.4.1.2011.5.25.143.1.52
This object is used to configure the LDP peer. The index of this table is hwLdpPeerLsrId.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwLdpPeerEntry

hwLdpPeerEntry 1.1.4.1.2011.5.25.143.1.52.1
An entry of the peer feature table, used to configure and display features, such as the MD5 password and split horizon policy negotiated with the local peer. The index of this entry is hwLdpPeerLsrId.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwLdpPeerEntry  

hwLdpPeerLsrId 1.1.4.1.2011.5.25.143.1.52.1.1
This object indicates the LSR ID of the LDP peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

hwLdpPeerMd5Type 1.1.4.1.2011.5.25.143.1.52.1.11
This object indicates the Md5 type. Options: 1. cipher(1) -indicates that the MD5 password is in cipher text mode. 2. plain(2) -indicates that the MD5 password is in plain text mode. 3. null(3) -indicates that the MD5 type is null, which means that the MD5 authentication is not configured for the LDP peer.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER cipher(1), plain(2), null(3)  

hwLdpPeerMd5Password 1.1.4.1.2011.5.25.143.1.52.1.12
This object indicates the MD5 password of LDP neighbor. To delete the password, set the password length as zero. When read, it always returns an Octet string with the length of zero.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

hwLdpPeerGtsmHops 1.1.4.1.2011.5.25.143.1.52.1.13
This object indicates the number of GTSM hops. The valid number of GTSM hops ranges from 1 to 255. To clear the configuration of GTSM hops, set the number of GTSM hops as 0.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..255  

hwLdpPeerSplitHorizon 1.1.4.1.2011.5.25.143.1.52.1.14
This object indicates the way to set the flag of split horizon for the specified LDP peer. Default: disabled
Status: current Access: read-create
OBJECT-TYPE    
  EnabledStatus  

hwLdpPeerReset 1.1.4.1.2011.5.25.143.1.52.1.15
This object indicates the reset of the neighbor services. Options: 1. reset(1) -indicates that the neighbor services will be reset. Only when the object is ready, can this value take effect. 2. ready(2) -indicates that it is ready to reset the neighbor services. This value cannot be set.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER reset(1), ready(2)  

hwLdpPeerKeychainName 1.1.4.1.2011.5.25.143.1.52.1.18
This object indicates the Keychain name. To cancel the Keychain authentication, set the Keychain name length as 0.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

hwLdpPeerOutBoundPolicyRange 1.1.4.1.2011.5.25.143.1.52.1.19
This object indicates the range of IGP routes for an outbound policy. The default value is clear. If the object is set as ipprefix, the value of hwLdpPeerOutBoundPolicyFecIpPrefix must be set together.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER clear(1), none(2), ipprefix(3), host(4)  

hwLdpPeerOutBoundPolicyFecIpPrefix 1.1.4.1.2011.5.25.143.1.52.1.20
This object indicates the IP prefix list name of IGP routes for an outbound policy. If the object is set with a value, the value of hwLdpPeerOutBoundPolicyRange must be set as ipprefix.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

hwLdpPeerOutBoundPolicyBgpRange 1.1.4.1.2011.5.25.143.1.52.1.21
This object indicates the range of BGP routes for an outbound policy. The default value is clear. If the object is set as ipprefix, the value of hwLdpPeerOutBoundPolicyBgpIpPrefix must be set together.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER clear(1), none(2), ipprefix(3)  

hwLdpPeerOutBoundPolicyBgpIpPrefix 1.1.4.1.2011.5.25.143.1.52.1.22
This object indicates the IP prefix list name of BGP routes for the outbound policy. If the object is set with a value, the value of hwLdpPeerOutBoundPolicyBgpRange must be set as ipprefix.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

hwLdpPeerInBoundPolicyRange 1.1.4.1.2011.5.25.143.1.52.1.23
This object indicates the route range for the inbound policy. The default value is clear. If the object is set as ipprefix, the value of hwLdpPeerInBoundPolicyFecIpPrefix must be set together.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER clear(1), none(2), ipprefix(3), host(4)  

hwLdpPeerInBoundPolicyFecIpPrefix 1.1.4.1.2011.5.25.143.1.52.1.24
This object indicates the IP prefix list name for the inbound policy. If the object is set with a value, the value of hwLdpPeerInBoundPolicyRange must be set as ipprefix.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

hwLdpPeerRowStatus 1.1.4.1.2011.5.25.143.1.52.1.51
This object indicates whether one entry of hwLdpPeerTable is created or destroyed. The value of this object can be CreatAndGo or Destroy. When the value of the object is set as CreatAndGo, and the entry is correctly created, the status of the object will change into active.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hwLdpVpnPeerTable 1.1.4.1.2011.5.25.143.1.53
This table is used to create and delete peer configurations in the LDP multi-instance. The indexs of this table are hwLdpVpnInstanceId, hwLdpVpnPeerLsrId. Make sure the corresponding LDP VPN-instance is already created in hwLdpVpnTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwLdpVpnPeerEntry

hwLdpVpnPeerEntry 1.1.4.1.2011.5.25.143.1.53.1
An entry of the VPN peer feature table, used to configure and display features, such as the MD5 password and split horizon policy negotiated with the local peer on the VPN. The indexs of this entry are hwLdpVpnInstanceId, hwLdpVpnPeerLsrId. Make sure the corresponding LDP VPN-instance is already created in hwLdpVpnTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwLdpVpnPeerEntry  

hwLdpVpnPeerLsrId 1.1.4.1.2011.5.25.143.1.53.1.1
This object indicates the LSR ID of the LDP peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

hwLdpVpnPeerMd5Type 1.1.4.1.2011.5.25.143.1.53.1.11
This object indicates the Md5 type. 1. cipher(1) -indicates that the MD5 password is in cipher text mode. 2. plain(2) -indicates that the MD5 password is in plain text mode. 3. null(3) -indicates that the MD5 type is null, which means that the MD5 authentication is not configured for the LDP peer.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER cipher(1), plain(2), null(3)  

hwLdpVpnPeerMd5Password 1.1.4.1.2011.5.25.143.1.53.1.12
This object indicates the MD5 password of VPN LDP neighbor. To delete the password, set the password length as zero. When read, it always returns an Octet string with the length of zero.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

hwLdpVpnPeerSplitHorizon 1.1.4.1.2011.5.25.143.1.53.1.13
This object indicates the way to set the flag of split horizon for the specified LDP peer. Default: disabled
Status: current Access: read-create
OBJECT-TYPE    
  EnabledStatus  

hwLdpVpnPeerReset 1.1.4.1.2011.5.25.143.1.53.1.14
This object indicates the reset of the neighbor services. Options: 1. reset(1) -indicates that the neighbor services will be reset. Only when the object is ready, can this value take effect. 2. ready(2) -indicates that it is ready to reset the neighbor services. This value cannot be set.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER reset(1), ready(2)  

hwLdpVpnPeerKeychainName 1.1.4.1.2011.5.25.143.1.53.1.17
This object indicates the Keychain name. To cancel the Keychain authentication, set the Keychain name length as 0.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

hwLdpVpnPeerRowStatus 1.1.4.1.2011.5.25.143.1.53.1.51
This object indicates whether one entry of hwLdpVpnPeerTable is created or destroyed. The value of this object can be CreatAndGo or Destroy. When the value of the object is set as CreatAndGo, and the entry is correctly created, the status of the object will change into active.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hwLdpInterfaceTable 1.1.4.1.2011.5.25.143.1.54
This table is used to configure or delete the LDP capability on the interface. The index of this table is hwLdpInterfaceIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwLdpInterfaceEntry

hwLdpInterfaceEntry 1.1.4.1.2011.5.25.143.1.54.1
An entry of the LDP interface table, used to configure and display the LDP negotiation parameters on the interface enabled with LDP capabilities. The index of this entry is hwLdpInterfaceIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwLdpInterfaceEntry  

hwLdpInterfaceIndex 1.1.4.1.2011.5.25.143.1.54.1.1
This object indicates the interface index. You can get the correct interface index based on ifIndex of ifTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

hwLdpStaticFrrProtectTimer 1.1.4.1.2011.5.25.143.1.54.1.11
This object indicates the value of static FRR protect timer. Default: 10 Unit: seconds
Status: obsolete Access: read-create
OBJECT-TYPE    
  Integer32 5..30  

hwLdpKeepAliveTimer 1.1.4.1.2011.5.25.143.1.54.1.12
This object indicates the value of Keepalive timer. Default: 45 Unit: seconds
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 30..65535  

hwLdpIgpSyncTimer 1.1.4.1.2011.5.25.143.1.54.1.13
This object indicates the value of IGP-Sync timer. By default, the timer is set to 10 seconds. Default: 10 Unit: seconds
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

hwLdpHelloTimer 1.1.4.1.2011.5.25.143.1.54.1.14
This object indicates the value of Hello hold timer. By default, the value of the timer is 15 seconds. Default: 15 Unit: seconds
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 3..65535  

hwLdpTransportAddressIfIndex 1.1.4.1.2011.5.25.143.1.54.1.15
This object indicates the way to specify the interface that the Transport Address is assigned to. Value: 0..2147483647 The default value of the object for the public interface is the interface that the LDP LSR ID is assigned to. If the LDP LSR ID is not assigned to any interface, then the value of the object is 0, and 0 cannot be set. The default value of the object for the private interface is the private interface itself. Based on mplsL3VpnIfConfRowStatus of mplsL3VpnIfConfTable, you can find which interface belongs to the VPN. The interface must be bound with the same VPN instance.
Status: current Access: read-create
OBJECT-TYPE    
  InterfaceIndexOrZero  

hwLdpKeepAliveSendTimer 1.1.4.1.2011.5.25.143.1.54.1.16
This object indicates the value of LDP Keepalive send timer. Default: 0 Unit: seconds
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

hwLdpHelloSendTimer 1.1.4.1.2011.5.25.143.1.54.1.17
This object indicates the value of LDP Hello send timer. Default: 0 Unit: seconds
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..65535  

hwLdpInterfaceLabelAdvertisementMode 1.1.4.1.2011.5.25.143.1.54.1.18
This object indicates the label distribution mode. Options: 1. dod(1) -indicates that the label distribution mode is dod. 2. du(2) -indicates that the label distribution mode is du. Default: du
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER dod(1), du(2)  

hwLdpInterfaceLocalLsrIdIfIndex 1.1.4.1.2011.5.25.143.1.54.1.19
This object indicates the way to specify the interface that the local LDP LSR-ID based on interface is assigned to. Value: 0..2147483647 The default value of the object for the public interface is the interface that the global LDP LSR ID is assigned to. If the global LDP LSR ID is not assigned to any interface, then the value of the object is 0. If set 0, the value of the object will be the default value. The default value of the object for the private interface is the interface that the global LDP LSR ID of VPN Instance is assigned to. Based on mplsL3VpnIfConfRowStatus of mplsL3VpnIfConfTable, you can find which interface belongs to the VPN. The interface which the object specified must be bound with the same VPN instance with the interface which is configured.
Status: current Access: read-create
OBJECT-TYPE    
  InterfaceIndexOrZero  

hwLdpInterfaceRowStatus 1.1.4.1.2011.5.25.143.1.54.1.51
This object indicates whether one entry of hwLdpInterfaceTable is created or destroyed. The value of this object can be CreatAndGo or Destroy. When the value of the object is set as CreatAndGo, and the entry is correctly created, the status of the object will change into active.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hwLdpPeerGroupTable 1.1.4.1.2011.5.25.143.1.58
This table is used to configure an LDP peer group.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwLdpPeerGroupEntry

hwLdpPeerGroupEntry 1.1.4.1.2011.5.25.143.1.58.1
An entry of this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwLdpPeerGroupEntry  

hwLdpPeerGroupName 1.1.4.1.2011.5.25.143.1.58.1.1
This object indicates the name of a peer group.
Status: current Access: not-accessible
OBJECT-TYPE    
  OCTET STRING Size(1..110)  

hwLdpPeerGroupOutBoundRange 1.1.4.1.2011.5.25.143.1.58.1.11
This object indicates the range of IGP routes for an outbound policy. The default value is clear. If the object is set as ipprefix, the value of hwLdpPeerGroupOutBoundFecIpPrefix must be set together.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER clear(1), none(2), ipprefix(3), host(4)  

hwLdpPeerGroupOutBoundFecIpPrefix 1.1.4.1.2011.5.25.143.1.58.1.12
This object indicates the IP prefix list name of IGP routes for an outbound policy. If the object is set with a value, the value of hwLdpPeerGroupOutBoundRange must be set as ipprefix.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

hwLdpPeerGroupOutBoundBgpRange 1.1.4.1.2011.5.25.143.1.58.1.13
This object indicates the range of BGP routes for an outbound policy. The default value is clear. If the object is set as ipprefix, the value of hwLdpPeerGroupOutBoundBgpIpPrefix must be set together.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER clear(1), none(2), ipprefix(3)  

hwLdpPeerGroupOutBoundBgpIpPrefix 1.1.4.1.2011.5.25.143.1.58.1.14
This object indicates the IP prefix list name of BGP routes for an outbound policy. If the object is set with a value, the value of hwLdpPeerGroupOutBoundBgpRange must be set as ipprefix.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

hwLdpPeerGroupInBoundRange 1.1.4.1.2011.5.25.143.1.58.1.15
This object indicates the route range for an inbound policy. The default value is clear. If the object is set as ipprefix, the value of hwLdpPeerGroupInBoundIpPrefix must be set together.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER clear(1), none(2), ipprefix(3), host(4)  

hwLdpPeerGroupInBoundIpPrefix 1.1.4.1.2011.5.25.143.1.58.1.16
This object indicates the IP prefix list name of routes for an inbound policy. If the object is set with a value, the value of hwLdpPeerGroupInBoundRange must be set as ipprefix.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

hwLdpPeerGroupRowStatus 1.1.4.1.2011.5.25.143.1.58.1.51
This object indicates whether one entry of hwLdpPolicyPeerGroupTable is created or destroyed. The value of this object is CreatAndGo or Destroy. When the value of the object is set to CreatAndGo, and the entry is correctly created, the status of the object will change into active.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hwLdpOutBoundPolicyPeerAllRange 1.1.4.1.2011.5.25.143.1.59
This object indicates the range of IGP routes for a global outbound LDP policy. The default value is all. If the object is set as ipprefix, the value of hwLdpOutBoundPolicyPeerAllFecIpPrefix must be set together.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER all(1), none(2), ipprefix(3), host(4)  

hwLdpOutBoundPolicyPeerAllFecIpPrefix 1.1.4.1.2011.5.25.143.1.60
This object indicates the IP prefix list name of IGP routes for a global outbound LDP policy. The default value is NULL. If the object is set with a value, the value of hwLdpOutBoundPolicyPeerAllRange must be set as ipprefix.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

hwLdpOutBoundPolicyPeerAllBgpRange 1.1.4.1.2011.5.25.143.1.61
This object indicates the range of BGP routes for a global outbound LDP policy. The default value is all. If the object is set as ipprefix, the value of hwLdpOutBoundPolicyPeerAllBgpIpPrefix must be set together.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER all(1), none(2), ipprefix(3)  

hwLdpOutBoundPolicyPeerAllBgpIpPrefix 1.1.4.1.2011.5.25.143.1.62
This object indicates the IP prefix list name of BGP routes for a global outbound LDP policy. The default value is NULL. If the object is set with a value, the value of hwLdpOutBoundPolicyPeerAllBgpRange must be set as ipprefix.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

hwLdpInBoundPolicyPeerAllRange 1.1.4.1.2011.5.25.143.1.63
This object indicates the range of routes for a global inbound LDP policy. The default value is all. If the object is set as ipprefix, the value of hwLdpInBoundPolicyPeerAllIpPrefix must be set together.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER all(1), none(2), ipprefix(3), host(4)  

hwLdpInBoundPolicyPeerAllIpPrefix 1.1.4.1.2011.5.25.143.1.64
This object indicates the IP prefix list name of routes for a global inbound LDP policy. The default value is NULL. If the object is set with a value, the value of hwLdpInBoundPolicyPeerAllRange must be set as ipprefix.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

hwLdpGracefulDeleteCapability 1.1.4.1.2011.5.25.143.1.65
This object indicates whether the LDP graceful-delete capability is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

hwLdpGracefulDeleteTimer 1.1.4.1.2011.5.25.143.1.66
The value of this object identifies the value of a graceful-delete timer. When the status of hwLdpGracefulDeleteCapability is enabled, the default value returned by the object is valid. Default: 5 Unit: seconds
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

hwLdpLspDownReason 1.1.4.1.2011.5.25.143.1.67
The LDP LSP down reason. Options: 1. other(1) -indicates other reasons. 2. session down(2) -indicates the ldp session went down. 3. route change(3) -indicates the route changed. 4. cannot recovery from GR(4) -indicates LSP cannot recovery from graceful-restart. 5. policy change(5) -indicates the policy changed.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER other(1), sessionDown(2), routeChange(3), canNotRecoveryFromGr(4), policyChange(5)  

hwLdpLspDownMplsLsrId 1.1.4.1.2011.5.25.143.1.68
This object indicates the LSR ID of failed router.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  MplsLsrIdentifier  

hwLdpLspDownOutIfIndex 1.1.4.1.2011.5.25.143.1.69
This object indicates the outgoing interface index of the failed router.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  InterfaceIndex  

hwLdpLspDownOutIfMainIp 1.1.4.1.2011.5.25.143.1.70
This object indicates the main ip address of the failed router's outgoing interface.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  IpAddress  

hwLdpLspDownOutIfState 1.1.4.1.2011.5.25.143.1.71
The state of the failed router's outgoing interface. Options: 1. up(1) -indicates that the state of the outgoing interface is Up. 2. down(2) -indicates that the state of the outgoing interface is Down.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER up(1), down(2)  

hwLdpLspDownDownstreamPeerLsrId 1.1.4.1.2011.5.25.143.1.72
This object indicates the failed router's downstream peer's LSR ID.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  MplsLdpIdentifier  

hwLdpSessionStatistics 1.1.4.1.2011.5.25.143.1.73
OBJECT IDENTIFIER    

hwLdpLocalOperationalSessionNumber 1.1.4.1.2011.5.25.143.1.73.1
This object indicates the number of local LDP operational sessions.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwLdpRemoteOperationalSessionNumber 1.1.4.1.2011.5.25.143.1.73.2
This object indicates the number of remote LDP operational sessions.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwLdpLocalAndRemoteOperationalSessionNumber 1.1.4.1.2011.5.25.143.1.73.3
This object indicates the number of local and remote LDP operational sessions.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwLdpTotalOperationalSessionNumber 1.1.4.1.2011.5.25.143.1.73.4
This object indicates the total number of LDP operational sessions.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwMplsLdpTrap 1.1.4.1.2011.5.25.143.2
OBJECT IDENTIFIER    

hwMplsLdpSessionDown 1.1.4.1.2011.5.25.143.2.1
When the trap indicating that a session is down is sent, the cause for the down LDP session is displayed.
Status: obsolete Access: read-only
NOTIFICATION-TYPE    

hwMplsLdpLspDown 1.1.4.1.2011.5.25.143.2.2
When the trap indicating that a session is down is sent, the cause for the down LSP session is displayed.
Status: obsolete Access: read-only
NOTIFICATION-TYPE    

hwMplsLdpHostIngressLspDownClear 1.1.4.1.2011.5.25.143.2.3
A trap is sent to clear the down trap of a specified FEC's ingress lsp.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwMplsLdpHostIngressLspDown 1.1.4.1.2011.5.25.143.2.4
A trap is sent when all the ingress lsp of a specified FEC went down.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwMplsLdpConformance 1.1.4.1.2011.5.25.143.3
OBJECT IDENTIFIER    

hwMplsLdpCompliances 1.1.4.1.2011.5.25.143.3.1
The Compliance statement for systems supporting the HUAWEI-MPLSLDP-MIB.
Status: current Access: read-only
MODULE-COMPLIANCE    

hwMplsLdpGroup 1.1.4.1.2011.5.25.143.3.2
OBJECT IDENTIFIER    

hwMplsLdpInfoGroup 1.1.4.1.2011.5.25.143.3.2.1
Infomation about LDP LSP.
Status: current Access: read-only
OBJECT-GROUP    

hwMplsLdpNotificationGroup 1.1.4.1.2011.5.25.143.3.2.2
Notification information included in the mib.
Status: obsolete Access: read-only
NOTIFICATION-GROUP    

hwMplsLdpLspDownNotificationGroup 1.1.4.1.2011.5.25.143.3.2.3
No use.
Status: obsolete Access: read-only
NOTIFICATION-GROUP    

hwMplsLdpGlobalGroup 1.1.4.1.2011.5.25.143.3.2.4
Information about Ldp Global configuration.
Status: current Access: read-only
OBJECT-GROUP    

hwMplsLdpVpnGlobalGroup 1.1.4.1.2011.5.25.143.3.2.5
Information about Ldp Vpn configuration.
Status: current Access: read-only
OBJECT-GROUP    

hwMplsLdpRemoteEntityGroup 1.1.4.1.2011.5.25.143.3.2.6
Information about remote entity.
Status: current Access: read-only
OBJECT-GROUP    

hwMplsLdpPeerGroup 1.1.4.1.2011.5.25.143.3.2.7
Information about Ldp Peer.
Status: current Access: read-only
OBJECT-GROUP    

hwMplsLdpVpnPeerGroup 1.1.4.1.2011.5.25.143.3.2.8
Information about Ldp Vpn Peer.
Status: current Access: read-only
OBJECT-GROUP    

hwMplsLdpInterfaceGroup 1.1.4.1.2011.5.25.143.3.2.9
Information about Ldp interface capability.
Status: current Access: read-only
OBJECT-GROUP    

hwLdpLspDownReasonGroup 1.1.4.1.2011.5.25.143.3.2.10
Information about Ldp ingress Lsp down reason.
Status: current Access: read-only
OBJECT-GROUP    

hwMplsLdpHostIngressLspDownNotificationGroup 1.1.4.1.2011.5.25.143.3.2.11
Notification information included in the mib.
Status: current Access: read-only
NOTIFICATION-GROUP    

hwLdpPolicyPeerGroupGroup 1.1.4.1.2011.5.25.143.3.2.15
Information about Ldp Policies of peer groups.
Status: current Access: read-only
OBJECT-GROUP    

hwMplsLdpFrrProtectGroup 1.1.4.1.2011.5.25.143.3.2.16
Information about Ldp FRR protect timer.
Status: obsolete Access: read-only
OBJECT-GROUP    

hwMplsLdpSessionStatisticsGroup 1.1.4.1.2011.5.25.143.3.2.17
Information about Ldp Session Statistics.
Status: current Access: read-only
OBJECT-GROUP