HPN-ICF-VOICE-IF-MIB

File: HPN-ICF-VOICE-IF-MIB.mib (7235 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC IF-MIB
HPN-ICF-OID-MIB

Imported symbols

OBJECT-TYPE MODULE-IDENTITY Integer32
DisplayString ifIndex hpnicfVoice

Defined Types

HPN-ICFVoiceIfConfigEntry  
SEQUENCE    
  hpnicfVoiceIfCfgCngOn INTEGER
  hpnicfVoiceIfCfgNonLinearSwitch INTEGER
  hpnicfVoiceIfCfgInputGain Integer32
  hpnicfVoiceIfCfgOutputGain Integer32
  hpnicfVoiceIfCfgEchoCancelSwitch INTEGER
  hpnicfVoiceIfCfgEchoCancelDelay Integer32
  hpnicfVoiceIfCfgTimerDialInterval Integer32
  hpnicfVoiceIfCfgTimerFirstDial Integer32
  hpnicfVoiceIfCfgPrivateline DisplayString
  hpnicfVoiceIfCfgRegTone OCTET STRING

Defined Values

hpnicfVoiceInterface 1.3.6.1.4.1.11.2.14.11.15.2.39.13
This MIB file is to provide the definition of the voice interface general configuration.
MODULE-IDENTITY    

hpnicfVoiceIfObjects 1.3.6.1.4.1.11.2.14.11.15.2.39.13.1
OBJECT IDENTIFIER    

hpnicfVoiceIfConfigTable 1.3.6.1.4.1.11.2.14.11.15.2.39.13.1.1
The table contains configurable parameters for both analog voice interface and digital voice interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HPN-ICFVoiceIfConfigEntry

hpnicfVoiceIfConfigEntry 1.3.6.1.4.1.11.2.14.11.15.2.39.13.1.1.1
The entry of voice interface table.
Status: current Access: not-accessible
OBJECT-TYPE    
  HPN-ICFVoiceIfConfigEntry  

hpnicfVoiceIfCfgCngOn 1.3.6.1.4.1.11.2.14.11.15.2.39.13.1.1.1.1
This object indicates whether the silence gaps should be filled with background noise. It is applicable to FXO, FXS, E&M subscriber lines and E1/T1 voice subscriber line.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hpnicfVoiceIfCfgNonLinearSwitch 1.3.6.1.4.1.11.2.14.11.15.2.39.13.1.1.1.2
This object expresses the nonlinear processing is enable or disable for the voice interface. It is applicable to FXO, FXS, E&M subscriber lines and E1/T1 voice subscriber line. Currently, only digital voice subscriber lines can be set disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hpnicfVoiceIfCfgInputGain 1.3.6.1.4.1.11.2.14.11.15.2.39.13.1.1.1.3
This object indicates the amount of gain added to the receiver side of the voice interface. Unit is 0.1 db. It is applicable to FXO, FXS, E&M subscriber lines and E1/T1 voice subscriber line.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -140..139  

hpnicfVoiceIfCfgOutputGain 1.3.6.1.4.1.11.2.14.11.15.2.39.13.1.1.1.4
This object indicates the amount of gain added to the send side of the voice interface. Unit is 0.1 db. It is applicable to FXO, FXS, E&M subscriber lines and E1/T1 voice subscriber line.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -140..139  

hpnicfVoiceIfCfgEchoCancelSwitch 1.3.6.1.4.1.11.2.14.11.15.2.39.13.1.1.1.5
This object indicates whether the echo cancellation is enabled. It is applicable to FXO, FXS, E&M subscriber lines and E1/T1 voice subscriber line.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hpnicfVoiceIfCfgEchoCancelDelay 1.3.6.1.4.1.11.2.14.11.15.2.39.13.1.1.1.6
This object indicates the delay of the echo cancellation for the voice interface. This value couldn't be modified unless hpnicfVoiceIfCfgEchoCancelSwitch is enable. Unit is milliseconds. It is applicable to FXO, FXS, E&M subscriber lines and E1/T1 voice subscriber line. The default value of this object is 32.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..64  

hpnicfVoiceIfCfgTimerDialInterval 1.3.6.1.4.1.11.2.14.11.15.2.39.13.1.1.1.7
The interval, in seconds, between two dialing numbers. The default value of this object is 10 seconds. It is applicable to FXO, FXS, E&M subscriber lines and E1/T1 with loop-start or ground-start protocol voice subscriber line.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..300  

hpnicfVoiceIfCfgTimerFirstDial 1.3.6.1.4.1.11.2.14.11.15.2.39.13.1.1.1.8
The period of time, in seconds, before dialing the first number. The default value of this object is 10 seconds. It is applicable to FXO, FXS subscriber lines and E1/T1 with loop-start or ground-start protocol voice subscriber line.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..300  

hpnicfVoiceIfCfgPrivateline 1.3.6.1.4.1.11.2.14.11.15.2.39.13.1.1.1.9
This object indicates the E.164 phone number for plar mode. It is applicable to FXO, FXS, E&M subscriber lines and E1/T1 voice subscriber line.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

hpnicfVoiceIfCfgRegTone 1.3.6.1.4.1.11.2.14.11.15.2.39.13.1.1.1.10
This object uses 2 or 3 letter country code specify voice parameters of different countrys. This value will take effect on all voice interfaces of all cards on the device.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0|2..3)