HPN-ICF-UNICAST-MIB
File:
HPN-ICF-UNICAST-MIB.mib (4067 bytes)
Imported modules
Imported symbols
Defined Types
| HpnicfURPFEntry |
|
| SEQUENCE |
|
|
|
| |
hpnicfURPFIfIndex |
Integer32 |
|
| |
hpnicfURPFEnabled |
TruthValue |
|
| |
hpnicfURPFSlotID |
Integer32 |
|
| |
hpnicfURPFTotalReceivedPacket |
Counter64 |
|
| |
hpnicfURPFDroppedPacket |
Counter64 |
|
| |
hpnicfURPFClearStat |
INTEGER |
|
Defined Values
| hpnicfUnicast |
1.3.6.1.4.1.11.2.14.11.15.2.44 |
| This MIB is a framework MIB for unicast related features. |
| MODULE-IDENTITY |
|
|
|
| hpnicfURPFTable |
1.3.6.1.4.1.11.2.14.11.15.2.44.1 |
| Unicast Reverse Path Forwarding (URPF) is used to prevent the network
attacks caused by source address spoofing. This table is used to configure
URPF on specific interfaces. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
HpnicfURPFEntry |
|
| hpnicfURPFEntry |
1.3.6.1.4.1.11.2.14.11.15.2.44.1.1 |
| The entry of hpnicfURPFTable, indexed by vlan interface index. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
HpnicfURPFEntry |
|
|
| hpnicfURPFIfIndex |
1.3.6.1.4.1.11.2.14.11.15.2.44.1.1.1 |
| The ifIndex of vlan interface. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| hpnicfURPFEnabled |
1.3.6.1.4.1.11.2.14.11.15.2.44.1.1.2 |
| This object is used to enable or disable URPF on certain vlan interfaces. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
TruthValue |
|
|
| hpnicfURPFSlotID |
1.3.6.1.4.1.11.2.14.11.15.2.44.1.1.3 |
| This object specifies to which slot packets are redirected in order to
perform URPF check. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| hpnicfURPFDroppedPacket |
1.3.6.1.4.1.11.2.14.11.15.2.44.1.1.5 |
| This object provides total dropped invalid packets number. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter64 |
|
|
| hpnicfURPFClearStat |
1.3.6.1.4.1.11.2.14.11.15.2.44.1.1.6 |
| This object is used to clear the URPF statistics on certain
vlan interfaces. This object is actually a write-only object.
When read, it always returns 0. When set to 1, the objects
hpnicfURPFTotalReceivedPacket and hpnicfURPFDroppedPacket are reset
to 0. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
reserved(0), reset(1) |
|