HPICF-IPSLA-MIB
File:
HPICF-IPSLA-MIB.mib (23115 bytes)
Imported modules
Imported symbols
Defined Types
| HpicfIpSlaEntry |
|
| SEQUENCE |
|
|
|
| |
hpicfIpSlaID |
Integer32 |
|
| |
hpicfIpSlaType |
INTEGER |
|
| |
hpicfIpSlaAdminState |
INTEGER |
|
| |
hpicfIpSlaSourceAddressType |
InetAddressType |
|
| |
hpicfIpSlaSourceAddress |
InetAddress |
|
| |
hpicfIpSlaL4SourcePort |
InetPortNumber |
|
| |
hpicfIpSlaSourceInterface |
InterfaceIndexOrZero |
|
| |
hpicfIpSlaDestAddressType |
InetAddressType |
|
| |
hpicfIpSlaDestAddress |
InetAddress |
|
| |
hpicfIpSlaL4DestPort |
InetPortNumber |
|
| |
hpicfIpSlaRowStatus |
RowStatus |
|
| HpicfIpSlaAttrEntry |
|
| SEQUENCE |
|
|
|
| |
hpicfIpSlaSchedStartTime |
DateAndTime |
|
| |
hpicfIpSlaSchedEndTime |
DateAndTime |
|
| |
hpicfIpSlaSchedFreq |
Unsigned32 |
|
| |
hpicfIpSlaSchedRepeat |
Unsigned32 |
|
| |
hpicfIpSlaAttrTOS |
Unsigned32 |
|
| |
hpicfIpSlaAttrHistorySize |
Unsigned32 |
|
| |
hpicfIpSlaAttrPayloadSize |
Unsigned32 |
|
| |
hpicfIpSlaAttrNumPkts |
Unsigned32 |
|
| |
hpicfIpSlaAttrPktInterval |
Unsigned32 |
|
| |
hpicfIpSlaAttrRowStatus |
RowStatus |
|
| HpicfIpSlaThrEntry |
|
| SEQUENCE |
|
|
|
| |
hpicfIpSlaThrMetricType |
INTEGER |
|
| |
hpicfIpSlaThrUpper |
Integer32 |
|
| |
hpicfIpSlaThrLower |
Integer32 |
|
| |
hpicfIpSlaThrType |
INTEGER |
|
| |
hpicfIpSlaThrCount |
Unsigned32 |
|
| |
hpicfIpSlaThrAction |
INTEGER |
|
| |
hpicfIpSlaThrRowStatus |
RowStatus |
|
| HpicfIpSlaRespEntry |
|
| SEQUENCE |
|
|
|
| |
hpicfIpSlaRespType |
INTEGER |
|
| |
hpicfIpSlaRespAddressType |
InetAddressType |
|
| |
hpicfIpSlaRespAddress |
InetAddress |
|
| |
hpicfIpSlaRespL4Port |
InetPortNumber |
|
| |
hpicfIpSlaRespRowStatus |
RowStatus |
|
Defined Values
| hpicfIpSla |
1.3.6.1.4.1.11.2.14.11.5.1.127 |
| This MIB module contains HP proprietary
objects for managing IP Service Level
Agreement (SLA). |
| MODULE-IDENTITY |
|
|
|
| hpicfIpSlaTable |
1.3.6.1.4.1.11.2.14.11.5.1.127.1.1 |
| This table specifies IP SLA test parameters as SLA entries. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
HpicfIpSlaEntry |
|
| hpicfIpSlaEntry |
1.3.6.1.4.1.11.2.14.11.5.1.127.1.1.1 |
| An entry on this table specifies the destination IP address/
Hostname, Source address, Source Interface ID & Row status
corresponding to each SLA test. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
HpicfIpSlaEntry |
|
|
| hpicfIpSlaID |
1.3.6.1.4.1.11.2.14.11.5.1.127.1.1.1.1 |
| This is an identifier for the IP SLA. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
1..255 |
|
| hpicfIpSlaType |
1.3.6.1.4.1.11.2.14.11.5.1.127.1.1.1.2 |
| SLA Probe Type. IcmpEcho is similar to ping protocol and
the destination should be enabled with responder
functionality for udpEcho, udpJitter, udpJitterVoIP and
tcpConnect. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
icmpEcho(1), udpEcho(2), udpJitter(3), udpJitterVoIP(4), tcpConnect(5) |
|
| hpicfIpSlaAdminState |
1.3.6.1.4.1.11.2.14.11.5.1.127.1.1.1.3 |
| Enable or disable the IP Service Level Agreement (SLA) probe. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enable(1), disable(2) |
|
| hpicfIpSlaL4SourcePort |
1.3.6.1.4.1.11.2.14.11.5.1.127.1.1.1.6 |
| SLA source port to be used for SLA probes that use a
transport layer such as udpEcho, udpJitter, udpJitterVoIP
and tcpConnect. The allowed range is from 1024 to 65535. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
InetPortNumber |
|
|
| hpicfIpSlaL4DestPort |
1.3.6.1.4.1.11.2.14.11.5.1.127.1.1.1.10 |
| Port on target device which responds back to the probe.
This is used for SLA probes that use a transport layer
such as udpEcho, udpJitter, udpJitterVoIP and tcpConnect
SLA types. The allowed range is from 1024 to 65535. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
InetPortNumber |
|
|
| hpicfIpSlaAttrTable |
1.3.6.1.4.1.11.2.14.11.5.1.127.1.2 |
| This table specifies IP SLA test parameters as SLA
entries. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
HpicfIpSlaAttrEntry |
|
| hpicfIpSlaAttrEntry |
1.3.6.1.4.1.11.2.14.11.5.1.127.1.2.1 |
| An entry on this table specifies the attributes of SLA
test such as scheduling parameters, TOS, payload size,
history bucket size and inter packet interval,
corresponding to each SLA test. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
HpicfIpSlaAttrEntry |
|
|
| hpicfIpSlaSchedEndTime |
1.3.6.1.4.1.11.2.14.11.5.1.127.1.2.1.2 |
| Timestamp to denote when to end this SLA probe. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
DateAndTime |
|
|
| hpicfIpSlaSchedFreq |
1.3.6.1.4.1.11.2.14.11.5.1.127.1.2.1.3 |
| Frequency in seconds. This value is used to send probes. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| hpicfIpSlaSchedRepeat |
1.3.6.1.4.1.11.2.14.11.5.1.127.1.2.1.4 |
| Number of times this test will be repeated. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| hpicfIpSlaAttrTOS |
1.3.6.1.4.1.11.2.14.11.5.1.127.1.2.1.5 |
| Type of service value to be set for the probe packet. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
0..255 |
|
| hpicfIpSlaAttrHistorySize |
1.3.6.1.4.1.11.2.14.11.5.1.127.1.2.1.6 |
| Number of history records to be maintained for SLA test.
Size can vary from 1 to 50. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| hpicfIpSlaAttrPayloadSize |
1.3.6.1.4.1.11.2.14.11.5.1.127.1.2.1.7 |
| Size of the packet payload to be sent out for each probe.
It can be set from 10 to 1440. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| hpicfIpSlaAttrNumPkts |
1.3.6.1.4.1.11.2.14.11.5.1.127.1.2.1.8 |
| Number of packets to be sent out for a single probe. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| hpicfIpSlaAttrPktInterval |
1.3.6.1.4.1.11.2.14.11.5.1.127.1.2.1.9 |
| Inter packet interval to be used for packets that are sent
out for a single probe. This value is not applicable if
the hpicfIpSlaAttrNumPkts is set to 1. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| hpicfIpSlaThrTable |
1.3.6.1.4.1.11.2.14.11.5.1.127.1.3 |
| This table specifies IP SLA threshold-action parameters as
entries. When one of the monitored parameters of an SLA
test goes beyond the configured thresholds, notifications
are generated either as traps or syslog messages. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
HpicfIpSlaThrEntry |
|
| hpicfIpSlaThrEntry |
1.3.6.1.4.1.11.2.14.11.5.1.127.1.3.1 |
| An entry on this table specifies the Metric type, upper
and lower limit of thresholds, threshold type and action
to be taken. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
HpicfIpSlaThrEntry |
|
|
| hpicfIpSlaThrMetricType |
1.3.6.1.4.1.11.2.14.11.5.1.127.1.3.1.1 |
| SLA metric type to be monitored. The rtt type is the round
trip time of the probe packet. The jitter type is the
inter-packet delay variance. The srcTodstTime type is the
one-way trip time from source to destination. The dstTosrcTtime
type is the one-way trip time from destination to source. The
Mean Opinion Scores (MOS) type is derived only for
udpJitterVoIP SLA. The Calculated Planning Impairment Factor
(ICPIF) type is derived only for udpJitterVoIP SLA. The
packetLoss type is to monitor loss of communication. The
testCompletion type is for notifying about the completion of
probe test. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
rtt(1), jitter(2), srcTodstTime(3), dstTosrcTime(4), mos(5), icpif(6), packetLoss(7), testCompletion(8) |
|
| hpicfIpSlaThrUpper |
1.3.6.1.4.1.11.2.14.11.5.1.127.1.3.1.2 |
| Acceptable upper-limit of threshold value for SLA. This
value is not applicable when hpicfIpSlaThrMetricType
is set to packetLoss and testCompletion. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| hpicfIpSlaThrLower |
1.3.6.1.4.1.11.2.14.11.5.1.127.1.3.1.3 |
| Acceptable lower-limit of threshold value for SLA. This
value is not applicable when hpicfIpSlaThrMetricType
is set to packetLoss and testCompletion. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| hpicfIpSlaThrType |
1.3.6.1.4.1.11.2.14.11.5.1.127.1.3.1.4 |
| Configure threshold type to trigger action. This value is
not applicable when hpicfIpSlaThrMetricType is set to
testCompletion. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
immediate(1), consecutive(2) |
|
| hpicfIpSlaThrCount |
1.3.6.1.4.1.11.2.14.11.5.1.127.1.3.1.5 |
| Configure the count of the number of times the threshold
value can cross the upper/lower limits. This value is
applicable only if hpicfIpSlaThrType is set to consecutive. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| hpicfIpSlaThrAction |
1.3.6.1.4.1.11.2.14.11.5.1.127.1.3.1.6 |
| The action to be taken when the threshold value
exceeds the limit. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
none(0), trap(1), log(2), trapAndLog(3) |
|
| hpicfIpSlaRespTable |
1.3.6.1.4.1.11.2.14.11.5.1.127.1.4 |
| This table specifies IP SLA responder parameters as entries. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
HpicfIpSlaRespEntry |
|
| hpicfIpSlaRespEntry |
1.3.6.1.4.1.11.2.14.11.5.1.127.1.4.1 |
| An entry on this table specifies the local IP address,
port number and row status corresponding to each SLA
responder config. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
HpicfIpSlaRespEntry |
|
|
| hpicfIpSlaRespType |
1.3.6.1.4.1.11.2.14.11.5.1.127.1.4.1.1 |
| The SLA responder type. The udpEcho and tcpConnect objects
are for UDP and TCP packets, respectively. The udpJitter
and udpJitterVoIP values calculate one-way delay, therefore
a timestamp has to be embedded while replying back. This is
one of the indexes for the hpicfIpSlaRespTable. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
udpEcho(1), udpJitter(2), udpJitterVoIP(3), tcpConnect(4) |
|
| hpicfIpSlaRespAddress |
1.3.6.1.4.1.11.2.14.11.5.1.127.1.4.1.3 |
| The local IP address to which the responder is bound.
This is one of the indexes for the hpicfIpSlaRespTable. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
InetAddress |
|
|
| hpicfIpSlaRespL4Port |
1.3.6.1.4.1.11.2.14.11.5.1.127.1.4.1.4 |
| L4 port number on hpicfIpSlaRespAddress where the responder
listens for probe packets from SLA source. This is one of
the indexes for the hpicfIpSlaRespTable. The allowed range
is from 1024 to 65535. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
InetPortNumber |
|
|
| hpicfIpSlaThresholdexceeded |
1.3.6.1.4.1.11.2.14.11.5.1.127.0.1 |
| This notification is generated when the metric calculated
from the SLA result exceeds the configured threshold value.
The hpicfIpSlaThrUpper is not applicable when
hpicfIpSlaThrMetricType is set to packetLoss or
testCompletion. |
| Status: current |
Access: read-create |
| NOTIFICATION-TYPE |
|
|
|
| hpicfIpSlaTestCompletion |
1.3.6.1.4.1.11.2.14.11.5.1.127.0.2 |
| This notification is generated when the SLA test is
completed either by reaching stopTime or
hpicfIpSlaAttrNumPkts. This notification is sent only
when the action type is set to trap or trap-log. |
| Status: current |
Access: read-create |
| NOTIFICATION-TYPE |
|
|
|
| hpicfIpSlaThresholdPktLoss |
1.3.6.1.4.1.11.2.14.11.5.1.127.0.3 |
| This notification is generated when SLA test probe reply
packets are lost consecutively for the configured number
of hpicfIpSlaThrCount. This notification is sent only when
the action type is set to trap or trap-log. |
| Status: current |
Access: read-create |
| NOTIFICATION-TYPE |
|
|
|
| hpicfIpSlaCompliance |
1.3.6.1.4.1.11.2.14.11.5.1.127.2.2.1 |
| The compliance statement for HP switches that support IP SLA. |
| Status: current |
Access: read-create |
| MODULE-COMPLIANCE |
|
|
|
| hpicfIpSlaGroup |
1.3.6.1.4.1.11.2.14.11.5.1.127.2.1.1 |
| A mandatory group with a set of IP SLA objects. |
| Status: current |
Access: read-create |
| OBJECT-GROUP |
|
|
|
| hpicfIpSlaAttrGroup |
1.3.6.1.4.1.11.2.14.11.5.1.127.2.1.2 |
| A group with a set of IP SLA attribute objects. |
| Status: current |
Access: read-create |
| OBJECT-GROUP |
|
|
|
| hpicfIpSlaThrGroup |
1.3.6.1.4.1.11.2.14.11.5.1.127.2.1.3 |
| A group with a set of IP SLA threshold objects. |
| Status: current |
Access: read-create |
| OBJECT-GROUP |
|
|
|
| hpicfIpSlaRespGroup |
1.3.6.1.4.1.11.2.14.11.5.1.127.2.1.4 |
| A group with a set of IP SLA responder objects. |
| Status: current |
Access: read-create |
| OBJECT-GROUP |
|
|
|
| hpicfIpSlaNotificationsGroup |
1.3.6.1.4.1.11.2.14.11.5.1.127.2.1.5 |
| A collection of IP SLA source and responder notifications
objects. |
| Status: current |
Access: read-create |
| NOTIFICATION-GROUP |
|
|
|