HP-SN-SWITCH-GROUP-MIB

File: HP-SN-SWITCH-GROUP-MIB.mib (165378 bytes)

Imported modules

RFC1155-SMI SNMPv2-SMI RFC-1212
HP-SN-ROOT-MIB

Imported symbols

Counter TimeTicks IpAddress
Gauge Unsigned32 OBJECT-TYPE
snSwitch

Defined Types

DisplayString  
OCTET STRING    

PhysAddress  
OCTET STRING    

MacAddress  
OCTET STRING Size(6)    

BridgeId  
OCTET STRING Size(8)    

Timeout  
INTEGER    

PortMask  
INTEGER    

InterfaceId  
OBJECT IDENTIFIER    

SnVLanByPortEntry  
SEQUENCE    
  snVLanByPortVLanIndex INTEGER
  snVLanByPortVLanId INTEGER
  snVLanByPortPortMask PortMask
  snVLanByPortQos INTEGER
  snVLanByPortStpMode INTEGER
  snVLanByPortStpPriority INTEGER
  snVLanByPortStpGroupMaxAge INTEGER
  snVLanByPortStpGroupHelloTime INTEGER
  snVLanByPortStpGroupForwardDelay INTEGER
  snVLanByPortRowStatus INTEGER
  snVLanByPortOperState INTEGER
  snVLanByPortBaseNumPorts INTEGER
  snVLanByPortBaseType INTEGER
  snVLanByPortStpProtocolSpecification INTEGER
  snVLanByPortStpMaxAge Timeout
  snVLanByPortStpHelloTime Timeout
  snVLanByPortStpHoldTime INTEGER
  snVLanByPortStpForwardDelay Timeout
  snVLanByPortStpTimeSinceTopologyChange TimeTicks
  snVLanByPortStpTopChanges Counter
  snVLanByPortStpRootCost INTEGER
  snVLanByPortStpRootPort INTEGER
  snVLanByPortStpDesignatedRoot BridgeId
  snVLanByPortBaseBridgeAddress MacAddress
  snVLanByPortVLanName DisplayString
  snVLanByPortRouterIntf INTEGER
  snVLanByPortChassisPortMask OCTET STRING
  snVLanByPortPortList OCTET STRING

SnVLanByPortMemberEntry  
SEQUENCE    
  snVLanByPortMemberVLanId INTEGER
  snVLanByPortMemberPortId INTEGER
  snVLanByPortMemberRowStatus INTEGER

SnVLanByPortCfgEntry  
SEQUENCE    
  snVLanByPortCfgVLanId INTEGER
  snVLanByPortCfgQos INTEGER
  snVLanByPortCfgStpMode INTEGER
  snVLanByPortCfgStpPriority INTEGER
  snVLanByPortCfgStpGroupMaxAge INTEGER
  snVLanByPortCfgStpGroupHelloTime INTEGER
  snVLanByPortCfgStpGroupForwardDelay INTEGER
  snVLanByPortCfgBaseNumPorts INTEGER
  snVLanByPortCfgBaseType INTEGER
  snVLanByPortCfgStpProtocolSpecification INTEGER
  snVLanByPortCfgStpMaxAge Timeout
  snVLanByPortCfgStpHelloTime Timeout
  snVLanByPortCfgStpHoldTime INTEGER
  snVLanByPortCfgStpForwardDelay Timeout
  snVLanByPortCfgStpTimeSinceTopologyChange TimeTicks
  snVLanByPortCfgStpTopChanges Counter
  snVLanByPortCfgStpRootCost INTEGER
  snVLanByPortCfgStpRootPort INTEGER
  snVLanByPortCfgStpDesignatedRoot BridgeId
  snVLanByPortCfgBaseBridgeAddress MacAddress
  snVLanByPortCfgVLanName DisplayString
  snVLanByPortCfgRouterIntf INTEGER
  snVLanByPortCfgRowStatus INTEGER

SnVLanByProtocolEntry  
SEQUENCE    
  snVLanByProtocolVLanId INTEGER
  snVLanByProtocolIndex INTEGER
  snVLanByProtocolDynamic INTEGER
  snVLanByProtocolStaticMask PortMask
  snVLanByProtocolExcludeMask PortMask
  snVLanByProtocolRouterIntf INTEGER
  snVLanByProtocolRowStatus INTEGER
  snVLanByProtocolDynamicMask PortMask
  snVLanByProtocolChassisStaticMask OCTET STRING
  snVLanByProtocolChassisExcludeMask OCTET STRING
  snVLanByProtocolChassisDynamicMask OCTET STRING
  snVLanByProtocolVLanName DisplayString
  snVLanByProtocolStaticPortList OCTET STRING
  snVLanByProtocolExcludePortList OCTET STRING
  snVLanByProtocolDynamicPortList OCTET STRING

SnVLanByIpSubnetEntry  
SEQUENCE    
  snVLanByIpSubnetVLanId INTEGER
  snVLanByIpSubnetIpAddress IpAddress
  snVLanByIpSubnetSubnetMask IpAddress
  snVLanByIpSubnetDynamic INTEGER
  snVLanByIpSubnetStaticMask PortMask
  snVLanByIpSubnetExcludeMask PortMask
  snVLanByIpSubnetRouterIntf INTEGER
  snVLanByIpSubnetRowStatus INTEGER
  snVLanByIpSubnetDynamicMask PortMask
  snVLanByIpSubnetChassisStaticMask OCTET STRING
  snVLanByIpSubnetChassisExcludeMask OCTET STRING
  snVLanByIpSubnetChassisDynamicMask OCTET STRING
  snVLanByIpSubnetVLanName DisplayString
  snVLanByIpSubnetStaticPortList OCTET STRING
  snVLanByIpSubnetExcludePortList OCTET STRING
  snVLanByIpSubnetDynamicPortList OCTET STRING

SnVLanByIpxNetEntry  
SEQUENCE    
  snVLanByIpxNetVLanId INTEGER
  snVLanByIpxNetNetworkNum OCTET STRING
  snVLanByIpxNetFrameType INTEGER
  snVLanByIpxNetDynamic INTEGER
  snVLanByIpxNetStaticMask PortMask
  snVLanByIpxNetExcludeMask PortMask
  snVLanByIpxNetRouterIntf INTEGER
  snVLanByIpxNetRowStatus INTEGER
  snVLanByIpxNetDynamicMask PortMask
  snVLanByIpxNetChassisStaticMask OCTET STRING
  snVLanByIpxNetChassisExcludeMask OCTET STRING
  snVLanByIpxNetChassisDynamicMask OCTET STRING
  snVLanByIpxNetVLanName DisplayString
  snVLanByIpxNetStaticPortList OCTET STRING
  snVLanByIpxNetExcludePortList OCTET STRING
  snVLanByIpxNetDynamicPortList OCTET STRING

SnVLanByATCableEntry  
SEQUENCE    
  snVLanByATCableVLanId INTEGER
  snVLanByATCableIndex INTEGER
  snVLanByATCableRouterIntf INTEGER
  snVLanByATCableRowStatus INTEGER
  snVLanByATCableChassisStaticMask OCTET STRING
  snVLanByATCableVLanName DisplayString
  snVLanByATCableStaticPortList OCTET STRING

SnSwPortInfoEntry  
SEQUENCE    
  snSwPortInfoPortNum INTEGER
  snSwPortInfoMonitorMode INTEGER
  snSwPortInfoTagMode INTEGER
  snSwPortInfoChnMode INTEGER
  snSwPortInfoSpeed INTEGER
  snSwPortInfoMediaType INTEGER
  snSwPortInfoConnectorType INTEGER
  snSwPortInfoAdminStatus INTEGER
  snSwPortInfoLinkStatus INTEGER
  snSwPortInfoPortQos INTEGER
  snSwPortInfoPhysAddress PhysAddress
  snSwPortStatsInFrames Counter
  snSwPortStatsOutFrames Counter
  snSwPortStatsAlignErrors Counter
  snSwPortStatsFCSErrors Counter
  snSwPortStatsMultiColliFrames Counter
  snSwPortStatsFrameTooLongs Counter
  snSwPortStatsTxColliFrames Counter
  snSwPortStatsRxColliFrames Counter
  snSwPortStatsFrameTooShorts Counter
  snSwPortLockAddressCount INTEGER
  snSwPortStpPortEnable INTEGER
  snSwPortDhcpGateListId INTEGER
  snSwPortName DisplayString
  snSwPortStatsInBcastFrames Counter
  snSwPortStatsOutBcastFrames Counter
  snSwPortStatsInMcastFrames Counter
  snSwPortStatsOutMcastFrames Counter
  snSwPortStatsInDiscard Counter
  snSwPortStatsOutDiscard Counter
  snSwPortStatsMacStations INTEGER
  snSwPortCacheGroupId INTEGER
  snSwPortTransGroupId INTEGER
  snSwPortInfoAutoNegotiate INTEGER
  snSwPortInfoFlowControl INTEGER
  snSwPortInfoGigType INTEGER
  snSwPortStatsLinkChange Counter
  snSwPortIfIndex INTEGER
  snSwPortDescr DisplayString
  snSwPortInOctets OCTET STRING
  snSwPortOutOctets OCTET STRING
  snSwPortStatsInBitsPerSec Gauge
  snSwPortStatsOutBitsPerSec Gauge
  snSwPortStatsInPktsPerSec Gauge
  snSwPortStatsOutPktsPerSec Gauge
  snSwPortStatsInUtilization INTEGER 0..10000
  snSwPortStatsOutUtilization INTEGER 0..10000
  snSwPortFastSpanPortEnable INTEGER
  snSwPortFastSpanUplinkEnable INTEGER
  snSwPortVlanId INTEGER
  snSwPortRouteOnly INTEGER
  snSwPortPresent INTEGER
  snSwPortGBICStatus INTEGER
  snSwPortStatsInKiloBitsPerSec Unsigned32
  snSwPortStatsOutKiloBitsPerSec Unsigned32
  snSwPortLoadInterval INTEGER 30..300
  snSwPortTagType INTEGER

SnInterfaceLookupEntry  
SEQUENCE    
  snInterfaceLookupInterfaceId InterfaceId
  snInterfaceLookupIfIndex INTEGER

SnIfIndexLookupEntry  
SEQUENCE    
  snIfIndexLookupIfIndex INTEGER
  snIfIndexLookupInterfaceId InterfaceId

SnFdbEntry  
SEQUENCE    
  snFdbStationIndex INTEGER
  snFdbStationAddr PhysAddress
  snFdbStationPort INTEGER
  snFdbVLanId INTEGER
  snFdbStationQos INTEGER
  snFdbStationType INTEGER
  snFdbRowStatus INTEGER

SnPortStpEntry  
SEQUENCE    
  snPortStpVLanId INTEGER
  snPortStpPortNum INTEGER
  snPortStpPortPriority INTEGER
  snPortStpPathCost INTEGER
  snPortStpOperState INTEGER
  snPortStpPortEnable INTEGER
  snPortStpPortForwardTransitions Counter
  snPortStpPortState INTEGER
  snPortStpPortDesignatedCost INTEGER
  snPortStpPortDesignatedRoot BridgeId
  snPortStpPortDesignatedBridge BridgeId
  snPortStpPortDesignatedPort OCTET STRING

SnTrunkEntry  
SEQUENCE    
  snTrunkIndex INTEGER
  snTrunkPortMask PortMask
  snTrunkType INTEGER

SnMSTrunkEntry  
SEQUENCE    
  snMSTrunkPortIndex INTEGER
  snMSTrunkPortList OCTET STRING
  snMSTrunkType INTEGER
  snMSTrunkRowStatus INTEGER

SnDhcpGatewayListEntry  
SEQUENCE    
  snDhcpGatewayListId INTEGER
  snDhcpGatewayListAddrList OCTET STRING
  snDhcpGatewayListRowStatus INTEGER

SnMacFilterEntry  
SEQUENCE    
  snMacFilterIndex INTEGER
  snMacFilterAction INTEGER
  snMacFilterSourceMac MacAddress
  snMacFilterSourceMask MacAddress
  snMacFilterDestMac MacAddress
  snMacFilterDestMask MacAddress
  snMacFilterOperator INTEGER
  snMacFilterFrameType INTEGER
  snMacFilterFrameTypeNum INTEGER
  snMacFilterRowStatus INTEGER

SnMacFilterPortAccessEntry  
SEQUENCE    
  snMacFilterPortAccessPortIndex INTEGER
  snMacFilterPortAccessFilters OCTET STRING
  snMacFilterPortAccessRowStatus INTEGER

SnNTPServerEntry  
SEQUENCE    
  snNTPServerIp IpAddress
  snNTPServerVersion INTEGER
  snNTPServerRowStatus INTEGER

SnRadiusServerEntry  
SEQUENCE    
  snRadiusServerIp IpAddress
  snRadiusServerAuthPort INTEGER
  snRadiusServerAcctPort INTEGER
  snRadiusServerRowStatus INTEGER
  snRadiusServerRowKey DisplayString
  snRadiusServerUsage INTEGER

SnTacacsServerEntry  
SEQUENCE    
  snTacacsServerIp IpAddress
  snTacacsServerAuthPort INTEGER
  snTacacsServerRowStatus INTEGER
  snTacacsServerRowKey DisplayString
  snTacacsServerUsage INTEGER

SnQosProfileEntry  
SEQUENCE    
  snQosProfileIndex INTEGER
  snQosProfileName DisplayString
  snQosProfileRequestedBandwidth INTEGER
  snQosProfileCalculatedBandwidth INTEGER

SnQosBindEntry  
SEQUENCE    
  snQosBindIndex INTEGER
  snQosBindPriority INTEGER
  snQosBindProfileIndex INTEGER

SnNetFlowCollectorEntry  
SEQUENCE    
  snNetFlowCollectorIndex INTEGER
  snNetFlowCollectorIp IpAddress
  snNetFlowCollectorUdpPort INTEGER
  snNetFlowCollectorSourceInterface INTEGER
  snNetFlowCollectorRowStatus INTEGER

SnNetFlowAggregationEntry  
SEQUENCE    
  snNetFlowAggregationIndex INTEGER
  snNetFlowAggregationIp IpAddress
  snNetFlowAggregationUdpPort INTEGER
  snNetFlowAggregationSourceInterface INTEGER
  snNetFlowAggregationNumberOfCacheEntries INTEGER
  snNetFlowAggregationActiveTimeout INTEGER
  snNetFlowAggregationInactiveTimeout INTEGER
  snNetFlowAggregationEnable INTEGER
  snNetFlowAggregationRowStatus INTEGER

SnNetFlowIfEntry  
SEQUENCE    
  snNetFlowIfIndex INTEGER
  snNetFlowIfFlowSwitching INTEGER

SnSflowCollectorEntry  
SEQUENCE    
  snSflowCollectorIndex INTEGER
  snSflowCollectorIP IpAddress
  snSflowCollectorUDPPort INTEGER
  snSflowCollectorRowStatus INTEGER

FdpInterfaceEntry  
SEQUENCE    
  snFdpInterfaceIfIndex INTEGER
  snFdpInterfaceFdpEnable INTEGER
  snFdpInterfaceCdpEnable INTEGER

FdpCacheEntry  
SEQUENCE    
  snFdpCacheIfIndex INTEGER
  snFdpCacheDeviceIndex INTEGER
  snFdpCacheDeviceId DisplayString
  snFdpCacheAddressType INTEGER
  snFdpCacheAddress OCTET STRING
  snFdpCacheVersion DisplayString
  snFdpCacheDevicePort DisplayString
  snFdpCachePlatform DisplayString
  snFdpCacheCapabilities DisplayString
  snFdpCacheVendorId INTEGER
  snFdpCacheIsAggregateVlan INTEGER
  snFdpCacheTagType INTEGER
  snFdpCachePortVlanMask OCTET STRING
  snFdpCachePortTagMode INTEGER
  snFdpCacheDefaultTrafficeVlanIdForDualMode INTEGER

FdpCachedAddressEntry  
SEQUENCE    
  snFdpCachedAddrIfIndex INTEGER
  snFdpCachedAddrDeviceIndex INTEGER
  snFdpCachedAddrDeviceAddrEntryIndex INTEGER
  snFdpCachedAddrType INTEGER
  snFdpCachedAddrValue OCTET STRING

Defined Values

snSwInfo 1.3.1
OBJECT IDENTIFIER    

snVLanInfo 1.3.2
OBJECT IDENTIFIER    

snSwPortInfo 1.3.3
OBJECT IDENTIFIER    

snFdbInfo 1.3.4
OBJECT IDENTIFIER    

snPortStpInfo 1.3.5
OBJECT IDENTIFIER    

snTrunkInfo 1.3.6
OBJECT IDENTIFIER    

snSwSummary 1.3.7
OBJECT IDENTIFIER    

snDhcpGatewayListInfo 1.3.8
OBJECT IDENTIFIER    

snDnsInfo 1.3.9
OBJECT IDENTIFIER    

snMacFilter 1.3.10
OBJECT IDENTIFIER    

snNTP 1.3.11
OBJECT IDENTIFIER    

snRadius 1.3.12
OBJECT IDENTIFIER    

snTacacs 1.3.13
OBJECT IDENTIFIER    

snQos 1.3.14
OBJECT IDENTIFIER    

snAAA 1.3.15
OBJECT IDENTIFIER    

snCAR 1.3.16
OBJECT IDENTIFIER    

snVLanCAR 1.3.17
OBJECT IDENTIFIER    

snNetFlow 1.3.18
OBJECT IDENTIFIER    

snSFlow 1.3.19
OBJECT IDENTIFIER    

snFDP 1.3.20
OBJECT IDENTIFIER    

snVsrp 1.3.21
OBJECT IDENTIFIER    

snSwGroupOperMode 1.3.1.1
noVLan(1) represents all switch ports with no virtual LAN by port (no Port VLAN), and with no tag assigned. vlanByPort(2) represents all switch ports with Basic VLAN (layer2 Switch).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noVLan(1), vlanByPort(2)  

snSwGroupIpL3SwMode 1.3.1.2
The Switch Group is configured with the Layer3 IP Switch mode either enabled or disabled and the default is disabled mode. enabled(1)...........activate Layer3 IP Switch disabled(0)..........disable Layer3 IP Switch
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

snSwGroupIpMcastMode 1.3.1.3
The Switch Group is configured with the IP Multicast pruning mode either enabled or disabled and the default is disabled mode. enabled(1)...........activate IP Multicast pruning disabled(0)..........no IP Multicast pruning
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

snSwGroupDefaultCfgMode 1.3.1.4
The Switch Group is configured with the Default configuration. If the default configuration gets overwritten, the state will change to non-default. default(1)...........default configuration nonDefault(2)..........non default configuration
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER default(1), nonDefault(2)  

snSwGroupSwitchAgeTime 1.3.1.5
The Switch Age time is 180sec by default. The configured range is 10 to 10,000sec. The time represents the time span to age out an MAC Address entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

snVLanGroupVlanCurEntry 1.3.1.6
The current total entry number of VLANs are configured.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

snVLanGroupSetAllVLan 1.3.1.7
The value of this object is the VLanIndex of a particalur entry in snVLanByPortTable (snVLanByPortVLanIndex). All the attributes of that row of table except PortMask will be used to set the same attributes for the entire VLan group. VLanId and PortMask must be set for that particular entry prior to setting this object. Switch software will base on that VLAN information to set the entire VLAN. Note: All the intended attributes of the given row of the table (given VLAN) must be set prior setting this object. When this object is set, Set-All-VLAN action will take place simultaneously. The previous setting will be overwritten by the new one.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

snSwPortSetAll 1.3.1.8
The value of this object is the index number of the snSwPortInfoTable (snSwPortInfoPortIndex). snSwPortInfoMonitorMode, snSwPortInfoTagMode, snSwPortInfoChnMode, snSwPortInfoSpeed, snSwPortInfoAdminStatus are all the read-write attributes of that row of table. They will be used to set the same attributes for all the ports in the system. Note: prior setting this object, all the intended attributes of the given row of the table must be set. Otherwise, the current data of the row will be used to set the entire port-table. The previous setting will be overwritten by the new one.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

snFdbTableCurEntry 1.3.1.9
The current total entry number of FDB are configured.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

snFdbTableStationFlush 1.3.1.10
The following values of the flush state can only be read: normal(1)... normal state error(2)... operation failed flushing(4)... in process The following value can be written: flush(3).....do flush The agent will return a response even before the flush is done. And the read value will be flushing until flush is done. And the flush request will be rejected until error or normal.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER normal(1), error(2), flush(3), flushing(4)  

snPortStpSetAll 1.3.1.11
The value of this object is 1 which means invoking Port STP Set-all command. The snPortStpPriority, snPortStpPathCost, the read-write STP related attributes of the first row of table will be used to set the same attributes for all the ports in the system. Note: prior setting this object, all the intended attributes of the given row of the table must be set. Otherwise, the current data of the row will be used to set the entire port-table. The previous setting will be overwritten by the new one.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

snSwProbePortNum 1.3.1.12
A chassis switch probe port is operated as a traffic analyzer port and only one port can be assigned in the chassis. The bit 0 to bit 7: port number. The bit 8 to bit 11: slot number. A stackable switch is only assigned with one probe port as a traffic analyzer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

snSw8021qTagMode 1.3.1.13
The Switch Group is configured with the IEEE802.1q Tagging mode either enabled or disabled and the default is disabled mode. enabled(1)...........activate IEEE802.1q Tagging mode. disabled(0)..........no IEEE802.1q Tagging.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

snSwGlobalStpMode 1.3.1.14
Spanning Tree System Global Mode in the Switch Group can be set either enabled or disabled and the default is enabled mode. enabled(1)...........activate Spanning Tree disabled(0)..........no Spanning Tree
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

snSwIpMcastQuerierMode 1.3.1.15
The IP Multicast pruning mode is configured either Non-Querier or Querier mode and the default is querier mode. querier(1)...........when prunning traffic locally within the VLAN. nonQuerier(2)........when running with a multicast capable router in the network.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER querier(1), nonQuerier(2)  

snSwViolatorPortNumber 1.3.1.17
The port number of the switch or router that received a violator packet. It is included in the locked address violation trap. The bit 0 to bit 7: port number. The bit 8 to bit 11: slot number (slot for chassis only).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

snSwViolatorMacAddress 1.3.1.18
The source address of the violator packet received by the switch or router. It is included in the locked address violation trap.
Status: mandatory Access: read-only
OBJECT-TYPE    
  MacAddress  

snVLanGroupVlanMaxEntry 1.3.1.19
The maximum number of VLAN entries are allowed to configure.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

snSwEosBufferSize 1.3.1.20
A specific buffer size for all the different EOS buffers.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

snVLanByPortEntrySize 1.3.1.21
The size of each VLAN table entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

snSwPortEntrySize 1.3.1.22
The size of each port table entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

snFdbStationEntrySize 1.3.1.23
The size of each Fdb station table entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

snPortStpEntrySize 1.3.1.24
The size of each port stp table entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

snSwEnableBridgeNewRootTrap 1.3.1.25
Indicates whether the SNMP agent process is permitted to generate bridge new root traps.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

snSwEnableBridgeTopoChangeTrap 1.3.1.26
Indicates whether the SNMP agent process is permitted to generate bridge topology change traps.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

snSwEnableLockedAddrViolationTrap 1.3.1.27
Indicates whether the SNMP agent process is permitted to generate locked address violation traps.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

snSwIpxL3SwMode 1.3.1.28
The Switch Group is configured with the Layer3 IPX Switch mode either enabled or disabled and the default is disabled mode. enabled(1)...........activate Layer3 Switch disabled(0)..........disable Layer3 Switch
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

snVLanByIpSubnetMaxSubnets 1.3.1.29
The maximum number of subnets for each IP VLAN.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

snVLanByIpxNetMaxNetworks 1.3.1.30
The maximum number of networks for each IPX VLAN.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

snSwProtocolVLanMode 1.3.1.31
disabled(0) - represents system with Protocol VLAN disabled. enabled(1) - represents system with Protocol VLAN enabled (Layer3 VLAN).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

snMacStationVLanId 1.3.1.32
This MAC Station VLAN ID index to the standard Forwarding Database for Transparent Bridge Table. (dot1dTpFdbTable). Since the dot1dTpFdbTable index is the MAC Address assigned to one of the ports in the bridge(VLAN) and each MAC address can be re-assigned to a different ports belonging to different bridges(VLANs), the snMacStationVLanId can be used by users to specify which bridge(VLAN) MAC Station information of the dot1dTpFdbTable users want to retrieve. If users do not specify the VLan ID in this MIB, the default VLAN (bridge) ID will be used when dot1dTpFdbTable is retrieved.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..4095  

snSwClearCounters 1.3.1.33
valid(0) - a SNMP-GET of this mib shows that it is valid command to use. clear(1) - represents clear counter command of the following counters: Dot3, MIB2, IP and IPX counters for all ports.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER valid(0), clear(1)  

snSw8021qTagType 1.3.1.34
The IEEE802.1q tag type embedded in the length/type field of an Ethernet packet. It specifies that the 2 octets after the length/type field in an Ethernet packet is the tag value.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

snSwBroadcastLimit 1.3.1.35
Limit the number of broadcast packets to forward out of the switch ports. This object specifies the number of broadcast packets per second. Setting a value of 0 to this object disables the limitation check.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

snSwMaxMacFilterPerSystem 1.3.1.36
The maximum number of MAC Filters per system in the MAC Filter table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

snSwMaxMacFilterPerPort 1.3.1.37
The maximum number of MAC Filters per port in the Port MAC Access Filter table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

snSwDefaultVLanId 1.3.1.38
The VLAN ID of the DEFAULT PORT-VLAN.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..4095  

snSwGlobalAutoNegotiate 1.3.1.39
This feature only applies to Gigabit Ethernet ports. If set to disable(0), all Gigabit Ethernet ports will be put to non- negotiation mode. If set to enable(1), all Gigabit Ethernet ports will start auto-negotiation indefinitely until succeed. If set to negFullAuto(2), all Gigabit Ethernet ports will start with auto-negotiation, if the negotiation failed, then they will automatically switch to non-negotiation mode. Stackable products (except TurboIron 8) Gigabit Ethernet ports do not support negFullAuto(2). If the snSwPortInfoAutoNegotiate value of a port was not set to global, this global value does not apply to the negotiation mode of that port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), negFullAuto(2), other(3)  

snSwQosMechanism 1.3.1.40
Indicates whether the qos mechanism is strict or weighted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER strict(0), weighted(1)  

snSwSingleStpMode 1.3.1.41
Single Spanning Tree System Mode in the Switch Group can be set either enabled or disabled and the default is disabled mode. enabled(1)...........activate Single Spanning Tree disabled(0)..........no Single Spanning Tree
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

snSwFastStpMode 1.3.1.42
Fast Spanning Tree System Mode in the Switch Group can be set either enabled or disabled and the default is enabled mode. enabled(1)...........activate Fast Spanning Tree disabled(0)..........no Fast Spanning Tree
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

snVLanByPortTable 1.3.2.1
If snSwGroupOperMode is configured as basic mode which is VLAN by Port, Layer2 switching, then this table is valid. Each VLAN switch port could have a number of VLAN IDs.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SnVLanByPortEntry

snVLanByPortEntry 1.3.2.1.1
An entry in the VLAN By Port Information table. snVLanByPortVLanIndex = 1 and with snVLanByPortVLanId = 1 together implies all attributes applying to the Global switch group i.e. noVLan. A SNMP SET PDU for a row of the snVLanByPortTable requires the entired sequence of the MIB Objects in each snVLanByPortEntry stored in one PDU. Otherwise, GENERR return-value will be returned.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SnVLanByPortEntry  

snVLanByPortVLanIndex 1.3.2.1.1.1
The VLAN ID index must not be greater than the snVLanGroupVlanMaxEntry. Each VLAN Identifier can have a membership of multiple ports.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER 1..4095  

snVLanByPortVLanId 1.3.2.1.1.2
The VLAN ID index to the VLAN By Port Info Table. Each VLAN Identifier can have a membership of multiple ports.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER 1..4095  

snVLanByPortPortMask 1.3.2.1.1.3
The Standand-alone switch VLAN port membership. (It was obsoleted for Chassis Product)
Status: deprecated Access: read-write
OBJECT-TYPE    
  PortMask  

snVLanByPortQos 1.3.2.1.1.4
The Stand alone stackable switch VLAN Priority values are: low(0) -- low prority high(1) -- high prority. The BigIron switch VLAN Priority values are: level0(0), level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7)
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER level0(0), level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7)  

snVLanByPortStpMode 1.3.2.1.1.5
Spanning Tree Mode in the Switch Group can be set either enabled or disabled and the default is enabled mode. enabled(1)...........activate Spanning Tree disabled(0)..........no Spanning Tree
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

snVLanByPortStpPriority 1.3.2.1.1.6
dot1dStpPriority : The value of the write-able portion of the Stp ID, i.e., the first two octets of the (8 octet long) Bridge ID. The other (last) 6 octets of the Bridge ID are given by the value of the base bridge address - dot1dBaseBridgeAddress.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

snVLanByPortStpGroupMaxAge 1.3.2.1.1.7
dot1dStpBridgeMaxAge: From RFC1493(Bridge MIB). The value that all bridges use for MaxAge when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of dot1dStpBridgeHelloTime. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER 6..40  

snVLanByPortStpGroupHelloTime 1.3.2.1.1.8
dot1dStpBridgeHelloTime: From RFC1493(Bridge MIB). The value that all bridges use for HelloTime when this bridge is acting as the root. The granularity of this timer is specified by 802.1D- 1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER 1..10  

snVLanByPortStpGroupForwardDelay 1.3.2.1.1.9
dot1dStpBridgeForwardDelay : From RFC1493(Bridge MIB). The value that all bridges use for ForwardDelay when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of dot1dStpBridgeMaxAge. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER 2..30  

snVLanByPortRowStatus 1.3.2.1.1.10
This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row other(1)....some other case valid(2)....the row exists and is valid
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER other(1), valid(2), delete(3), create(4), modify(5)  

snVLanByPortOperState 1.3.2.1.1.11
By default, this mode is set to notActivated(0). notActivated(0)...the VLAN entry is not activated and not in running mode. activated(1)......the VLAN entry is activated and in running mode
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER notActivated(0), activated(1)  

snVLanByPortBaseNumPorts 1.3.2.1.1.12
The number of ports controlled by this bridging entity.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

snVLanByPortBaseType 1.3.2.1.1.13
Indicates what type of bridging this bridge can perform. If a bridge is actually performing a certain type of bridging this will be indicated by entries in the port table for the given type.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER unknown(1), transparent-only(2), sourceroute-only(3), srt(4)  

snVLanByPortStpProtocolSpecification 1.3.2.1.1.14
An indication of what version of the Spanning Tree Protocol is being run. The value 'decLb100(2)' indicates the DEC LANbridge 100 Spanning Tree protocol. IEEE 802.1d implementations will return 'ieee8021d(3)'. If future versions of the IEEE Spanning Tree Protocol are released that are incompatible with the current version a new value will be defined.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER unknown(1), decLb100(2), ieee8021d(3)  

snVLanByPortStpMaxAge 1.3.2.1.1.15
dot1dStpMaxAge: From RFC1493(Bridge MIB). The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Timeout  

snVLanByPortStpHelloTime 1.3.2.1.1.16
dot1dStpHelloTime: From RFC1493(Bridge MIB). The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Timeout  

snVLanByPortStpHoldTime 1.3.2.1.1.17
dot1dStpHoldTime: From RFC1493(Bridge MIB). This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

snVLanByPortStpForwardDelay 1.3.2.1.1.18
dot1dStpForwardDelay: From RFC1493(Bridge MIB). This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. [Note that this value is the one that this bridge is currently using, in contrast to dot1dStpBridgeForwardDelay which is the value that this bridge and all others would start using if/when this bridge were to become the root.]
Status: deprecated Access: read-only
OBJECT-TYPE    
  Timeout  

snVLanByPortStpTimeSinceTopologyChange 1.3.2.1.1.19
The time (in hundredths of a second) since the last time a topology change was detected by the bridge entity.
Status: deprecated Access: read-only
OBJECT-TYPE    
  TimeTicks  

snVLanByPortStpTopChanges 1.3.2.1.1.20
The total number of topology changes detected by this bridge since the management entity was last reset or initialized.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Counter  

snVLanByPortStpRootCost 1.3.2.1.1.21
dot1dStpRootCost: From RFC1493(Bridge MIB). The cost of the path to the root as seen from this bridge.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

snVLanByPortStpRootPort 1.3.2.1.1.22
dot1dStpRootPort: From RFC1493(Bridge MIB). The port number of the port which offers the lowest cost path from this bridge to the root bridge.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

snVLanByPortStpDesignatedRoot 1.3.2.1.1.23
dot1dStpDesignatedRoot: From RFC1493(Bridge MIB). The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
Status: deprecated Access: read-only
OBJECT-TYPE    
  BridgeId  

snVLanByPortBaseBridgeAddress 1.3.2.1.1.24
The MAC address used by this bridge when it must be referred to in a unique fashion. It is recommended that this be the numerically smallest MAC address of all ports that belong to this bridge. However it is only required to be unique. When concatenated with dot1dStpPriority a unique BridgeIdentifier is formed which is used in the Spanning Tree Protocol.
Status: deprecated Access: read-only
OBJECT-TYPE    
  MacAddress  

snVLanByPortVLanName 1.3.2.1.1.25
VLAN Community Name string.
Status: deprecated Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

snVLanByPortRouterIntf 1.3.2.1.1.26
Optional: A virtual interface for router to the VLAN -- applied to router only. If a SNMP-Get value is zero, that means this object was not configured.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER 1..60  

snVLanByPortChassisPortMask 1.3.2.1.1.27
The Chassis VLAN switch port membership. (It was obsoleted after release 07100, replaced by snVLanByPortPortList)
Status: deprecated Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(32)  

snVLanByPortPortList 1.3.2.1.1.28
A list of port indices which are the port membership of a VLAN By Port. Each port index is a 16-bit integer in big endian order. 8-bit is the slot number, the other 8-bit is the port number.
Status: deprecated Access: read-write
OBJECT-TYPE    
  OCTET STRING  

snVLanByPortMemberTable 1.3.2.6
Port VLAN (Layer 2 VLAN) port membership table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SnVLanByPortMemberEntry

snVLanByPortMemberEntry 1.3.2.6.1
An entry of the port VLAN membership table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SnVLanByPortMemberEntry  

snVLanByPortMemberVLanId 1.3.2.6.1.1
The VLAN identifier (VLAN ID).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..4095  

snVLanByPortMemberPortId 1.3.2.6.1.2
The ifIndex which is a member of the port VLAN.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

snVLanByPortMemberRowStatus 1.3.2.6.1.3
This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row other(1)....some other case valid(2)....the row exists and is valid
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), valid(2), delete(3), create(4)  

snVLanByPortCfgTable 1.3.2.7
Port VLAN (Layer 2 VLAN) configuration table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SnVLanByPortCfgEntry

snVLanByPortCfgEntry 1.3.2.7.1
An entry of the port VLAN configuration table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SnVLanByPortCfgEntry  

snVLanByPortCfgVLanId 1.3.2.7.1.1
The VLAN identifier (VLAN ID).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..4095  

snVLanByPortCfgQos 1.3.2.7.1.2
The Stand alone stackable switch VLAN Priority values are: level0(0) -- low prority level1(1) -- high prority. The BigIron switch VLAN Priority values are: level0(0), level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7)
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER level0(0), level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7)  

snVLanByPortCfgStpMode 1.3.2.7.1.3
Spanning Tree Mode in the Switch Group can be set either enabled or disabled and the default is enabled mode. enabled(1)...........activate Spanning Tree disabled(0)..........no Spanning Tree
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

snVLanByPortCfgStpPriority 1.3.2.7.1.4
dot1dStpPriority : The value of the write-able portion of the Stp ID, i.e., the first two octets of the (8 octet long) Bridge ID. The other (last) 6 octets of the Bridge ID are given by the value of the base bridge address - dot1dBaseBridgeAddress.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

snVLanByPortCfgStpGroupMaxAge 1.3.2.7.1.5
dot1dStpBridgeMaxAge: From RFC1493(Bridge MIB). The value that all bridges use for MaxAge when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of dot1dStpBridgeHelloTime. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 6..40  

snVLanByPortCfgStpGroupHelloTime 1.3.2.7.1.6
dot1dStpBridgeHelloTime: From RFC1493(Bridge MIB). The value that all bridges use for HelloTime when this bridge is acting as the root. The granularity of this timer is specified by 802.1D- 1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..10  

snVLanByPortCfgStpGroupForwardDelay 1.3.2.7.1.7
dot1dStpBridgeForwardDelay : From RFC1493(Bridge MIB). The value that all bridges use for ForwardDelay when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of dot1dStpBridgeMaxAge. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 2..30  

snVLanByPortCfgBaseNumPorts 1.3.2.7.1.8
The number of ports controlled by this bridging entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

snVLanByPortCfgBaseType 1.3.2.7.1.9
Indicates what type of bridging this bridge can perform. If a bridge is actually performing a certain type of bridging this will be indicated by entries in the port table for the given type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER unknown(1), transparent-only(2), sourceroute-only(3), srt(4)  

snVLanByPortCfgStpProtocolSpecification 1.3.2.7.1.10
An indication of what version of the Spanning Tree Protocol is being run. The value 'decLb100(2)' indicates the DEC LANbridge 100 Spanning Tree protocol. IEEE 802.1d implementations will return 'ieee8021d(3)'. If future versions of the IEEE Spanning Tree Protocol are released that are incompatible with the current version a new value will be defined.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER unknown(1), decLb100(2), ieee8021d(3)  

snVLanByPortCfgStpMaxAge 1.3.2.7.1.11
dot1dStpMaxAge: From RFC1493(Bridge MIB). The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Timeout  

snVLanByPortCfgStpHelloTime 1.3.2.7.1.12
dot1dStpHelloTime: From RFC1493(Bridge MIB). The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Timeout  

snVLanByPortCfgStpHoldTime 1.3.2.7.1.13
dot1dStpHoldTime: From RFC1493(Bridge MIB). This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

snVLanByPortCfgStpForwardDelay 1.3.2.7.1.14
dot1dStpForwardDelay: From RFC1493(Bridge MIB). This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. [Note that this value is the one that this bridge is currently using, in contrast to dot1dStpBridgeForwardDelay which is the value that this bridge and all others would start using if/when this bridge were to become the root.]
Status: mandatory Access: read-only
OBJECT-TYPE    
  Timeout  

snVLanByPortCfgStpTimeSinceTopologyChange 1.3.2.7.1.15
The time (in hundredths of a second) since the last time a topology change was detected by the bridge entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

snVLanByPortCfgStpTopChanges 1.3.2.7.1.16
The total number of topology changes detected by this bridge since the management entity was last reset or initialized.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snVLanByPortCfgStpRootCost 1.3.2.7.1.17
dot1dStpRootCost: From RFC1493(Bridge MIB). The cost of the path to the root as seen from this bridge.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

snVLanByPortCfgStpRootPort 1.3.2.7.1.18
dot1dStpRootPort: From RFC1493(Bridge MIB). The port number of the port which offers the lowest cost path from this bridge to the root bridge.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

snVLanByPortCfgStpDesignatedRoot 1.3.2.7.1.19
dot1dStpDesignatedRoot: From RFC1493(Bridge MIB). The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
Status: mandatory Access: read-only
OBJECT-TYPE    
  BridgeId  

snVLanByPortCfgBaseBridgeAddress 1.3.2.7.1.20
The MAC address used by this bridge when it must be referred to in a unique fashion. It is recommended that this be the numerically smallest MAC address of all ports that belong to this bridge. However it is only required to be unique. When concatenated with dot1dStpPriority a unique BridgeIdentifier is formed which is used in the Spanning Tree Protocol.
Status: mandatory Access: read-only
OBJECT-TYPE    
  MacAddress  

snVLanByPortCfgVLanName 1.3.2.7.1.21
VLAN Community Name string.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

snVLanByPortCfgRouterIntf 1.3.2.7.1.22
Optional: A virtual interface for router to the VLAN -- applied to router only. If a SNMP-Get value is zero, that means this object was not configured.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

snVLanByPortCfgRowStatus 1.3.2.7.1.23
Use object to delete a vlan entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), valid(2), delete(3)  

snVLanByProtocolTable 1.3.2.2
.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SnVLanByProtocolEntry

snVLanByProtocolEntry 1.3.2.2.1
An entry in the VLAN By Protocol Configuration table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SnVLanByProtocolEntry  

snVLanByProtocolVLanId 1.3.2.2.1.1
The VLAN ID index to both of the VLAN By Port Info Table and this table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..4095  

snVLanByProtocolIndex 1.3.2.2.1.2
The following IP/IPX protocol VLAN types are operated in Layer3 VLAN such as : ip(1), ipx(2), ipv6(7) The following are operated in Layer2 bridging such as: appleTalk(3), decNet(4), netBios(5), others(6) -- other protocols which are defined here.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ip(1), ipx(2), appleTalk(3), decNet(4), netBios(5), others(6), ipv6(7)  

snVLanByProtocolDynamic 1.3.2.2.1.3
disabled(0) : disabled dynamic port inclusion - applied to switch only. enabled(1) : enabled dynamic port inclusion - applied to switch only.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

snVLanByProtocolStaticMask 1.3.2.2.1.4
The Standand-alone switch Protocol VLAN port membership applied in static mode. (It was obsoleted for Chassis Product)
Status: deprecated Access: read-write
OBJECT-TYPE    
  PortMask  

snVLanByProtocolExcludeMask 1.3.2.2.1.5
The Standand-alone switch Protocol VLAN port membership applied in exclusive mode. (It was obsoleted for Chassis Product)
Status: deprecated Access: read-write
OBJECT-TYPE    
  PortMask  

snVLanByProtocolRouterIntf 1.3.2.2.1.6
Optional: A virtual interface for router to the VLAN -- applied to router only. If a SNMP-Get value is zero, that means this object was not configured.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..60  

snVLanByProtocolRowStatus 1.3.2.2.1.7
This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row other(1)....some other case valid(2)....the row exists and is valid
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), valid(2), delete(3), create(4), modify(5)  

snVLanByProtocolDynamicMask 1.3.2.2.1.8
The Standand-alone switch Protocol VLAN active port membership. (It was obsoleted for Chassis Product)
Status: deprecated Access: read-only
OBJECT-TYPE    
  PortMask  

snVLanByProtocolChassisStaticMask 1.3.2.2.1.9
The Chassis Protocol VLAN port membership applied in static mode. (It was obsoleted after release 07100, replaced by snVLanByProtocolStaticPortList)
Status: deprecated Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(32)  

snVLanByProtocolChassisExcludeMask 1.3.2.2.1.10
The Chassis Protocol VLAN port membership applied in exclusive mode. (It was obsoleted after release 07100, replaced by snVLanByProtocolExcludePortList)
Status: deprecated Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(32)  

snVLanByProtocolChassisDynamicMask 1.3.2.2.1.11
The Chassis Protocol VLAN active port membership. (It was obsoleted after release 07100, replaced by snVLanByProtocolDynamicPortList)
Status: deprecated Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(32)  

snVLanByProtocolVLanName 1.3.2.2.1.12
VLAN Community Name string.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

snVLanByProtocolStaticPortList 1.3.2.2.1.13
A list of port indices which are the configured port membership of the Protocol VLAN. Each port index is a 16-bit integer in big endian order. 8-bit is the slot number, the other 8-bit is the port number.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

snVLanByProtocolExcludePortList 1.3.2.2.1.14
A list of port indices which are the excluded from port membership of the Protocol VLAN. Each port index is a 16-bit integer in big endian order. 8-bit is the slot number, the other 8-bit is the port number.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

snVLanByProtocolDynamicPortList 1.3.2.2.1.15
A list of port indices which are dynamically joining the port membership of the Protocol VLAN. Each port index is a 16-bit integer in big endian order. 8-bit is the slot number, the other 8-bit is the port number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

snVLanByIpSubnetTable 1.3.2.3
An entry of the VLAN By IPX Network Number Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SnVLanByIpSubnetEntry

snVLanByIpSubnetEntry 1.3.2.3.1
An entry in the VLAN By IP Subnet Configuration table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SnVLanByIpSubnetEntry  

snVLanByIpSubnetVLanId 1.3.2.3.1.1
The VLAN ID index to both of the VLAN By Port Info Table and this table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..4095  

snVLanByIpSubnetIpAddress 1.3.2.3.1.2
Subnet IP address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

snVLanByIpSubnetSubnetMask 1.3.2.3.1.3
Subnet mask associated with the Subnet IP address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

snVLanByIpSubnetDynamic 1.3.2.3.1.4
disabled(0) : disabled dynamic port inclusion - applied to switch only. enabled(1) : enabled dynamic port inclusion - applied to switch only.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

snVLanByIpSubnetStaticMask 1.3.2.3.1.5
The Standand-alone switch VLAN By Subnet port membership applied in static mode. (It was obsoleted for Chassis Product)
Status: deprecated Access: read-write
OBJECT-TYPE    
  PortMask  

snVLanByIpSubnetExcludeMask 1.3.2.3.1.6
The Standand-alone switch VLAN By Subnet port membership applied in exclusive mode. (It was obsoleted for Chassis Product)
Status: deprecated Access: read-write
OBJECT-TYPE    
  PortMask  

snVLanByIpSubnetRouterIntf 1.3.2.3.1.7
Optional: A virtual interface for router to the VLAN -- applied to router only. If a SNMP-Get value is zero, that means this object was not configured.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..60  

snVLanByIpSubnetRowStatus 1.3.2.3.1.8
This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row other(1)....some other case valid(2)....the row exists and is valid
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), valid(2), delete(3), create(4), modify(5)  

snVLanByIpSubnetDynamicMask 1.3.2.3.1.9
The Standand-alone switch VLAN By Subnet active port membership. (It was obsoleted for Chassis Product)
Status: deprecated Access: read-only
OBJECT-TYPE    
  PortMask  

snVLanByIpSubnetChassisStaticMask 1.3.2.3.1.10
The Chassis VLAN By Subnet port membership applied in static mode. (It was obsoleted after release 07100, replaced by snVLanByIpSubnetStaticPortList)
Status: deprecated Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(32)  

snVLanByIpSubnetChassisExcludeMask 1.3.2.3.1.11
The Chassis VLAN By Subnet port membership applied in exclusive mode. (It was obsoleted after release 07100, replaced by snVLanByIpSubnetExcludePortList)
Status: deprecated Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(32)  

snVLanByIpSubnetChassisDynamicMask 1.3.2.3.1.12
The Chassis VLAN By Subnet active port membership. (It was obsoleted after release 07100, replaced by snVLanByIpSubnetDynamicPortList)
Status: deprecated Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(32)  

snVLanByIpSubnetVLanName 1.3.2.3.1.13
VLAN Community Name string.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

snVLanByIpSubnetStaticPortList 1.3.2.3.1.14
A list of port indices which are the configured port membership of the VLAN By IP Subnet. Each port index is a 16-bit integer in big endian order. 8-bit is the slot number, the other 8-bit is the port number.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

snVLanByIpSubnetExcludePortList 1.3.2.3.1.15
A list of port indices which are the excluded from port membership of the VLAN By IP Subnet. Each port index is a 16-bit integer in big endian order. 8-bit is the slot number, the other 8-bit is the port number.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

snVLanByIpSubnetDynamicPortList 1.3.2.3.1.16
A list of port indices which are dynamically joining the port membership of the VLAN By IP Subnet. Each port index is a 16-bit integer in big endian order. 8-bit is the slot number, the other 8-bit is the port number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

snVLanByIpxNetTable 1.3.2.4
An entry of the VLAN By IPX Network Number Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SnVLanByIpxNetEntry

snVLanByIpxNetEntry 1.3.2.4.1
An entry in the VLAN By Ipx Network Number Configuration table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SnVLanByIpxNetEntry  

snVLanByIpxNetVLanId 1.3.2.4.1.1
The VLAN ID index to both of the VLAN By Port Info Table and this table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..4095  

snVLanByIpxNetNetworkNum 1.3.2.4.1.2
IPX Network Number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(4)  

snVLanByIpxNetFrameType 1.3.2.4.1.3
The following IPX Frame types are operated in Layer3 VLAN such as : ipxEthernet8022(1), ipxEthernet8023(2), ipxEthernetII(3), ipxEthernetSnap(4). choose notApplicable(0) for other protocols. Note: Each Network Number can be assigned with one unique Frame type; Otherwise, a SNMP-SET error will be returned.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(0), ipxEthernet8022(1), ipxEthernet8023(2), ipxEthernetII(3), ipxEthernetSnap(4)  

snVLanByIpxNetDynamic 1.3.2.4.1.4
disabled(0) : disabled dynamic port inclusion - applied to switch only. enabled(1) : enabled dynamic port inclusion - applied to switch only.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

snVLanByIpxNetStaticMask 1.3.2.4.1.5
The VLAN By IPX network port membership applied in static mode. (It was obsoleted for Chassis Product)
Status: deprecated Access: read-write
OBJECT-TYPE    
  PortMask  

snVLanByIpxNetExcludeMask 1.3.2.4.1.6
The VLAN By IPX network port membership applied in exclusive mode. (It was obsoleted for Chassis Product)
Status: deprecated Access: read-write
OBJECT-TYPE    
  PortMask  

snVLanByIpxNetRouterIntf 1.3.2.4.1.7
Optional: A virtual interface for router to the VLAN -- applied to router only. If a SNMP-Get value is zero, that means this object was not configured.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..60  

snVLanByIpxNetRowStatus 1.3.2.4.1.8
This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row other(1)....some other case valid(2)....the row exists and is valid
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), valid(2), delete(3), create(4), modify(5)  

snVLanByIpxNetDynamicMask 1.3.2.4.1.9
The VLAN By IPX network active port membership. (It was obsoleted for Chassis Product)
Status: deprecated Access: read-only
OBJECT-TYPE    
  PortMask  

snVLanByIpxNetChassisStaticMask 1.3.2.4.1.10
The Chassis VLAN By IPX network port membership applied in static mode. (It was obsoleted after release 07100, replaced by snVLanByIpxNetStaticPortList)
Status: deprecated Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(32)  

snVLanByIpxNetChassisExcludeMask 1.3.2.4.1.11
The Chassis VLAN By IPX network port membership applied in exclusive mode. (It was obsoleted after release 07100, replaced by snVLanByIpxNetExcludePortList)
Status: deprecated Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(32)  

snVLanByIpxNetChassisDynamicMask 1.3.2.4.1.12
The Chassis VLAN By IPX network active port membership. (It was obsoleted after release 07100, replaced by snVLanByIpxNetDynamicPortList)
Status: deprecated Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(32)  

snVLanByIpxNetVLanName 1.3.2.4.1.13
VLAN Community Name string.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

snVLanByIpxNetStaticPortList 1.3.2.4.1.14
A list of port indices which are the configured port membership of the VLAN By IPX network. Each port index is a 16-bit integer in big endian order. 8-bit is the slot number, the other 8-bit is the port number.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

snVLanByIpxNetExcludePortList 1.3.2.4.1.15
A list of port indices which are the excluded from port membership of the VLAN By IPX network. Each port index is a 16-bit integer in big endian order. 8-bit is the slot number, the other 8-bit is the port number.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

snVLanByIpxNetDynamicPortList 1.3.2.4.1.16
A list of port indices which are dynamically joining the port membership of the VLAN By IPX network. Each port index is a 16-bit integer in big endian order. 8-bit is the slot number, the other 8-bit is the port number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

snVLanByATCableTable 1.3.2.5
A Table Of VLAN By AppleTalk Network Number.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SnVLanByATCableEntry

snVLanByATCableEntry 1.3.2.5.1
An entry of the AppleTalk Cable VLAN table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SnVLanByATCableEntry  

snVLanByATCableVLanId 1.3.2.5.1.1
The VLAN ID of a PORT VLAN of which the AppleTalk Cable VLAN was attaching to.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..4095  

snVLanByATCableIndex 1.3.2.5.1.2
AppleTalk Cable VLAN index number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

snVLanByATCableRouterIntf 1.3.2.5.1.3
A virtual router interface to the AppleTalk Cable VLAN, only router products accept the SNMP-SET operation. The value zero indicates that virtual router interface was not configured.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..60  

snVLanByATCableRowStatus 1.3.2.5.1.4
This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row other(1)....some other case valid(2)....the row exists and is valid
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), valid(2), delete(3), create(4), modify(5)  

snVLanByATCableChassisStaticMask 1.3.2.5.1.5
A list of ports which are statically configured to become port members of a VLAN. (It was obsoleted after release 07100, replaced by snVLanByATCableStaticPortList)
Status: deprecated Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(32)  

snVLanByATCableVLanName 1.3.2.5.1.6
VLAN Name string.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

snVLanByATCableStaticPortList 1.3.2.5.1.7
A list of port indices which are the configured port membership of the AppleTalk Cable VLAN. Each port index is a 16-bit integer in big endian order. 8-bit is the slot number, the other 8-bit is the port number.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

snSwPortInfoTable 1.3.3.1
A specific snSwPortInfo group consists of a number of switch ports.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SnSwPortInfoEntry

snSwPortInfoEntry 1.3.3.1.1
An entry in the snSwPortInfo table indicates the configuration on a specified port. A SNMP SET PDU for a row of the snSwPortInfoTable requires the entired sequence of the MIB Objects in each snSwPortInfoEntry stored in one PDU. Otherwise, GENERR return-value will be returned.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SnSwPortInfoEntry  

snSwPortInfoPortNum 1.3.3.1.1.1
The port index. The bit 0 to bit 7: port number. The bit 8 to bit 11: slot number (slot for chassis only).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

snSwPortInfoMonitorMode 1.3.3.1.1.2
A monitoring port is selected and its traffic will be analyzed if the mode is not disabled(0), which is the default mode. The values are: disabled(0) -- No traffic monitoring input(1) -- traffic monitoring is activated on packets received output(2) -- traffic monitoring is activated on packets transmitted both(3) -- traffic monitoring is activated on packets received and transmitted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), input(1), output(2), both(3)  

snSwPortInfoTagMode 1.3.3.1.1.3
For tagged port, we could have multiple VLANs per port. For untagged port or auto port, there is only one VLAN ID per port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER tagged(1), untagged(2), auto(3), disabled(4)  

snSwPortInfoChnMode 1.3.3.1.1.4
The port can be configured to operate in either half or full duplex mode. The values are: halfDuplex(1)...half duplex mode fullDuplex(2)...full duplex mode The read-back channel status from hardware are: none(0).........link down or port disabled. halfDuplex(1)...half duplex mode fullDuplex(2)...full duplex mode The port media type (expansion or regular) and port link type (trunk or feeder) determine value of this object. The port can not set to half duplex mode if the port connect mode is m200e(4). However, the value of this parameter may be automatically set whenever the expansion port is connected (e.g. cascade connecting device).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(0), halfDuplex(1), fullDuplex(2)  

snSwPortInfoSpeed 1.3.3.1.1.5
The speed configuration for a port. The values are: none(0)..........link down or no traffic. sAutoSense(1)....Auto-sensing 10 or 100Mbits. s10M(2)..........10Mbits per second. s100M(3).........100Mbits per second. s1G(4)...........1Gbits per second. s45M(5)..........45Mbits per second (T3) (for expansion board only). s155M(6).........155Mbits per second (ATM) (for expansion board only). s10G(7)..........10Gbits per second. The read-back hardware status are the following: none(0)..........link down or no traffic. s10M(2)..........10Mbits per second. s100M(3).........100Mbits per second. s1G(4)...........1Gbits per second. s45M(5)..........45Mbits per second (T3) (for expansion board only). s155M(6).........155Mbits per second (ATM) (for expansion board only). s10G(7)..........10Gbits per second. The port media type (expansion or regular) and port link type (trunk or feeder) determine whether this object can be written and the valid values. It is not allowed to change speed for trunks ports. For expansion ports, all of the above speed can be set. However, the value of this parameter may be automatically set whenever the expansion port is connected (e.g. cascade connecting device).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(0), sAutoSense(1), s10M(2), s100M(3), s1G(4), s45M(5), s155M(6), s10G(7)  

snSwPortInfoMediaType 1.3.3.1.1.6
The media type for the port. The values are: other(1).........other or unknown media. m100BaseTX(2)....100Mbits per second copper. m100BaseFX(3)....100Mbits per second fiber. m1000BaseFX(4)...1Gbits per second fiber. mT3(5)...........45Mbits per second (T3). m155ATM(6).......155Mbits per second (ATM). m1000BaseTX(7)...1Gbits per second copper. m622ATM(8).......622Mbits per second (ATM). m155POS(9).......155Mbits per second (POS). m622POS(10)......622Mbits per second (POS). m2488POS(11).....2488Mbits per second (POS). m10000BaseFX(12).10Gbits per second fiber.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), m100BaseTX(2), m100BaseFX(3), m1000BaseFX(4), mT3(5), m155ATM(6), m1000BaseTX(7), m622ATM(8), m155POS(9), m622POS(10), m2488POS(11), m10000BaseFX(12)  

snSwPortInfoConnectorType 1.3.3.1.1.7
The type of connector that the port offers. The values are: other(1)...........other or unknown connector copper(2)..........Copper connector fiber(3)...........Fiber connector This describes the physical connector type
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), copper(2), fiber(3)  

snSwPortInfoAdminStatus 1.3.3.1.1.8
The desired state of all ports. The testing(3) state indicates that no operational packets can be passed. (same as ifAdminStatus in MIB-II)
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3)  

snSwPortInfoLinkStatus 1.3.3.1.1.9
The current operational state of the interface. The testing(3) state indicates that no operational packets can be passed. (same as ifOperStatus in MIB-II)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3)  

snSwPortInfoPortQos 1.3.3.1.1.10
The Stand alone stackable switch Port Qos Priority values are: low(0) -- low prority high(1) -- high prority. The BigIron Port Qos Priority values are: level0(0), level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7)
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER level0(0), level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7)  

snSwPortInfoPhysAddress 1.3.3.1.1.11
The port physical address. The physical address represents the switch port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PhysAddress  

snSwPortStatsInFrames 1.3.3.1.1.12
The total number of packets received on the interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snSwPortStatsOutFrames 1.3.3.1.1.13
The total number of packets transmitted out of the interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snSwPortStatsAlignErrors 1.3.3.1.1.14
dot3StatsAlignmentErrors : A count of frames received on a particular interface that are not an integral number of octets in length and do not pass the FCS check. The count represented by an instance of this object is incremented when the alignmentError status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions obtain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snSwPortStatsFCSErrors 1.3.3.1.1.15
dot3StatsFCSErrors : A count of frames received on a particular interface that are an integral number of octets in length but do not pass the FCS check. The count represented by an instance of this object is incremented when the frameCheckError status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions obtain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snSwPortStatsMultiColliFrames 1.3.3.1.1.16
dot3StatsMultipleCollisionFrames : A count of successfully transmitted frames on a particular interface for which transmission is inhibited by more than one collision. A frame that is counted by an instance of this object is also counted by the corresponding instance of either the ifOutUcastPkts, ifOutMulticastPkts, or ifOutBroadcastPkts, and is not counted by the corresponding instance of the dot3StatsSingleCollisionFrames object.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snSwPortStatsFrameTooLongs 1.3.3.1.1.17
dot3StatsFrameTooLongs : A count of frames received on a particular interface that exceed the maximum permitted frame size. The count represented by an instance of this object is incremented when the frameTooLong status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions obtain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snSwPortStatsTxColliFrames 1.3.3.1.1.18
A count of successfully transmitted frames on a particular interface for which transmission is inhibited by more than one collision. A frame that is counted by a combination of both dot3StatsSingleCollisionFrames and dot3StatsMultipleCollisionFrames objects.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snSwPortStatsRxColliFrames 1.3.3.1.1.19
A count of successfully received frames on a particular interface for which transmission is inhibited by more than one collision. This object is not specified in dot3 but it has the same functionarity as snSwPortStatsTxColliFrames.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snSwPortStatsFrameTooShorts 1.3.3.1.1.20
A count of frames received on a particular interface that below the minimum permitted frame size.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snSwPortLockAddressCount 1.3.3.1.1.21
The number of source MAC addresses are allowed for a port. Writing 0 to this object will allow any number of addresses.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2048  

snSwPortStpPortEnable 1.3.3.1.1.22
The enabled/disabled status of the port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

snSwPortDhcpGateListId 1.3.3.1.1.23
The ID for a DHCP gateway list entry relative to this switch port. 0 = unset or no assigned ID
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..32  

snSwPortName 1.3.3.1.1.24
Port Name string.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..255)  

snSwPortStatsInBcastFrames 1.3.3.1.1.25
The total number of broadcast packets received on the interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snSwPortStatsOutBcastFrames 1.3.3.1.1.26
The total number of broadcast packets transmitted out of the interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snSwPortStatsInMcastFrames 1.3.3.1.1.27
The total number of multicast packets received on the interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snSwPortStatsOutMcastFrames 1.3.3.1.1.28
The total number of multicast packets transmitted out of the interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snSwPortStatsInDiscard 1.3.3.1.1.29
The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snSwPortStatsOutDiscard 1.3.3.1.1.30
The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snSwPortStatsMacStations 1.3.3.1.1.31
The total number of MAC Stations connected to the interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

snSwPortCacheGroupId 1.3.3.1.1.32
Cache Group ID for the interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

snSwPortTransGroupId 1.3.3.1.1.33
Transparent Group ID for the interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

snSwPortInfoAutoNegotiate 1.3.3.1.1.34
This feature only applies to Gigabit Ethernet ports. If set to disable(0), port will be put to non-negotiation mode. If set to enable(1), port will start auto-negotiation indefinitely until succeed. If set to negFullAuto(2), the port will start with auto- negotiation, if the negotiation failed, then it will automatically switch to non-negotiation mode. Stackable products (except TurboIron 8) Gigabit Ethernet ports do not support negFullAuto(2). If set to global(3), port negotiation mode follows the value of snSwGlobalAutoNegotiate. Non-Gigabit Ethernet port returns the value other(4).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1), negFullAuto(2), global(3), other(4)  

snSwPortInfoFlowControl 1.3.3.1.1.35
Enable/Disbale port flow control.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

snSwPortInfoGigType 1.3.3.1.1.36
The media type for the port. The values are: m1000BaseSX(0)....1Gbits per second fiber, with a short wavelength transceiver. m1000BaseLX(1)....1Gbits per second fiber, with a long wavelength transceiver (3km). m1000BaseLH(2)....1Gbits per second fiber, with a special wavelength transceiver (50km). m1000BaseLHA(3)....1Gbits per second fiber, with a special wavelength transceiver (70km). m1000BaseLHB(4)....1Gbits per second fiber, with a special wavelength transceiver (150km). m1000BaseTX(5)....1Gbits per second copper (100meter). m10000BaseSR(6)....10Gbits per second fiber, with a short range wavelength transceiver (100m). m10000BaseLR(7)....10Gbits per second fiber, with a long range wavelength transceiver (10km). m10000BaseER(8)....10Gbits per second fiber, with a extended range wavelength transceiver (40km). notApplicable(255)....a non-gigabit port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER m1000BaseSX(0), m1000BaseLX(1), m1000BaseLH(2), m1000BaseLHA(3), m1000BaseLHB(4), m1000BaseTX(5), m10000BaseSR(6), m10000BaseLR(7), m10000BaseER(8), notApplicable(255)  

snSwPortStatsLinkChange 1.3.3.1.1.37
The total number of link state change of the interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snSwPortIfIndex 1.3.3.1.1.38
In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in RFC 1213 and RFC 1573.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

snSwPortDescr 1.3.3.1.1.39
A textual string containing the slot/port information about the interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

snSwPortInOctets 1.3.3.1.1.40
The total number of octets received on the interface, including framing characters. This object is a 64-bit counter of the ifInOctets object, defined in RFC 1213. The octet string is in big-endian byte order.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(8)  

snSwPortOutOctets 1.3.3.1.1.41
The total number of octets transmitted out of the interface, including framing characters. This object is a 64-bit counter of the ifOutOctets object, defined in RFC 1213. The octet string is in big-endian byte order.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(8)  

snSwPortStatsInBitsPerSec 1.3.3.1.1.42
The number of bits per second received on the interface over a 5 minutes interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

snSwPortStatsOutBitsPerSec 1.3.3.1.1.43
The number of bits per second transmitted out of the interface over a 5 minutes interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

snSwPortStatsInPktsPerSec 1.3.3.1.1.44
The number of packets per second received on the interface over a 5 minutes interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

snSwPortStatsOutPktsPerSec 1.3.3.1.1.45
The number of packets per second transmitted out of the interface over a 5 minutes interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

snSwPortStatsInUtilization 1.3.3.1.1.46
The input network utilization in hundredths of a percent over a 5 minutes interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..10000  

snSwPortStatsOutUtilization 1.3.3.1.1.47
The output network utilization in hundredths of a percent over a 5 minutes interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..10000  

snSwPortFastSpanPortEnable 1.3.3.1.1.48
The enabled/disabled fast span port status of the port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

snSwPortFastSpanUplinkEnable 1.3.3.1.1.49
The enabled/disabled fast span uplink status of the port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

snSwPortVlanId 1.3.3.1.1.50
The ID of a VLAN of which this port is a member. Port must be untagged. For tagged port which belongs to multiple VLANs, this object return 0 which is an invalid VLAN ID value.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..4095  

snSwPortRouteOnly 1.3.3.1.1.51
Enable/Disable L2 switching of a routing switch port. By default, the routing switch performs routing first. If routing failed, it performs switching. Enable route only instrcuts the routing switch to perform routing only. For a L2 switching only product, reading this object always return 'disabled', writing 'enabled' to this object takes no effect.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

snSwPortPresent 1.3.3.1.1.52
Indicate if the port is absent or present. This object only valid for M4 module
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER false(0), true(1)  

snSwPortGBICStatus 1.3.3.1.1.53
Indicate if the gig port has GBICs on them. If set to GBIC(1), it means that the port is GBIC. If set to miniGBIC(2), it means that the port miniGBIC. If set to empty(3), it means that the GBIC is missing. Value other(4) means that the port not a removable gig port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER gbic(1), miniGBIC(2), empty(3), other(4)  

snSwPortStatsInKiloBitsPerSec 1.3.3.1.1.54
Bit rate in kilobits per second received on the 10G and faster interface over a 5 minutes interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32  

snSwPortStatsOutKiloBitsPerSec 1.3.3.1.1.55
Bit rate in kilobits per second transmitted out of the 10G and faster interface over a 5 minutes interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Unsigned32  

snSwPortLoadInterval 1.3.3.1.1.56
The time in seconds for which average port utilization should be carried out. The value should be incremental of 30 seconds, between the ranges specified.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 30..300  

snSwPortTagType 1.3.3.1.1.57
The IEEE802.1q tag type embedded in the length/type field of an Ethernet packet. It specifies that the 2 octets after the length/type field in an Ethernet packet is the tag value.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

snInterfaceId 1.3.3.2
OBJECT IDENTIFIER    

snInterfaceLookupTable 1.3.3.3
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SnInterfaceLookupEntry

snInterfaceLookupEntry 1.3.3.3.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SnInterfaceLookupEntry  

snInterfaceLookupInterfaceId 1.3.3.3.1.1
Tok_String
Status: mandatory Access: read-only
OBJECT-TYPE    
  InterfaceId  

snInterfaceLookupIfIndex 1.3.3.3.1.2
Tok_String
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

snIfIndexLookupTable 1.3.3.4
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SnIfIndexLookupEntry

snIfIndexLookupEntry 1.3.3.4.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SnIfIndexLookupEntry  

snIfIndexLookupIfIndex 1.3.3.4.1.1
Tok_String
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

snIfIndexLookupInterfaceId 1.3.3.4.1.2
Tok_String
Status: mandatory Access: read-only
OBJECT-TYPE    
  InterfaceId  

snFdbTable 1.3.4.1
This table contains snFdb information for each station known to the system, one entry per station.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SnFdbEntry

snFdbEntry 1.3.4.1.1
Each entry represents the information of a static MAC station.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SnFdbEntry  

snFdbStationIndex 1.3.4.1.1.1
The FDB Station index to the Fdb Station Table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..256  

snFdbStationAddr 1.3.4.1.1.2
The snFdbs physical address. The physical address represents a MAC Station.
Status: mandatory Access: read-write
OBJECT-TYPE    
  PhysAddress  

snFdbStationPort 1.3.4.1.1.3
Station slot/port number. The bit 0 to bit 7: port number. The bit 8 to bit 11: slot number (slot for chassis only).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

snFdbVLanId 1.3.4.1.1.4
The Station VLan ID.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

snFdbStationQos 1.3.4.1.1.5
The Stand alone stackable station Qos Priority values are: low(0) -- low prority high(1) -- high prority. The BigIron switch station Priority values are: level0(0), level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7)
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER level0(0), level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7)  

snFdbStationType 1.3.4.1.1.6
The station type values are: notSupported -- a read value only : this product does not support MultiLayer Switching. host -- any MAC station. router -- a router-typed station.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER notSupported(0), host(1), router(2)  

snFdbRowStatus 1.3.4.1.1.7
This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row other(1)....some other case valid(2)....the row exists and is valid
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), valid(2), delete(3), create(4)  

snPortStpTable 1.3.5.1
A specific snPortStpTable consists of a number of switch ports. This table only exists if only if snVLanByPortTable exists and snVLanByPortStpMode is enabled for each VLAN.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SnPortStpEntry

snPortStpEntry 1.3.5.1.1
An entry in the snPortStpTable indicates the configuration on a specified port. A SNMP SET PDU for a row of the snPortStpTable requires the entired sequence of the MIB Objects in each snPortStpEntry stored in one PDU. Otherwise, GENERR return-value will be returned.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SnPortStpEntry  

snPortStpVLanId 1.3.5.1.1.1
The VLAN ID of the VLAN switch community.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

snPortStpPortNum 1.3.5.1.1.2
The port number of the Switch. The bit 0 to bit 7: port number. The bit 8 to bit 11: slot number (slot for chassis only).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

snPortStpPortPriority 1.3.5.1.1.3
The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID. The other octet of the Port ID is given by the value of dot1dStpPort.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 8..255  

snPortStpPathCost 1.3.5.1.1.4
dot1dStpPortPathCost : The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1990 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN. Writing value zero to this object sets path cost to a default value which automatically changes according to port speed. Reading value zero indicates an unknown path cost value because port speed cannot be determined due to speed auto sense in progress.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

snPortStpOperState 1.3.5.1.1.5
By default, this mode is set to notActivated(0). notActivated(0)...the Port STP entry is not activated and not in running mode. activated(1)......the Port STP entry is activated and in running mode
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notActivated(0), activated(1)  

snPortStpPortEnable 1.3.5.1.1.6
The enabled/disabled status of the port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

snPortStpPortForwardTransitions 1.3.5.1.1.7
The number of times this port has transitioned from the Learning state to the Forwarding state.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Counter  

snPortStpPortState 1.3.5.1.1.8
The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the broken(6) state. For ports which are disabled (see dot1dStpPortEnable), this object will have a value of disabled(1).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(1), blocking(2), listening(3), learning(4), forwarding(5), broken(6)  

snPortStpPortDesignatedCost 1.3.5.1.1.9
The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

snPortStpPortDesignatedRoot 1.3.5.1.1.10
The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.
Status: mandatory Access: read-only
OBJECT-TYPE    
  BridgeId  

snPortStpPortDesignatedBridge 1.3.5.1.1.11
The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment.
Status: mandatory Access: read-only
OBJECT-TYPE    
  BridgeId  

snPortStpPortDesignatedPort 1.3.5.1.1.12
The Port Identifier of the port on the Designated Bridge for this port's segment.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2)  

snTrunkTable 1.3.6.1
A specific snTrunkTable consists of a number of Trunk port-mask.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SnTrunkEntry

snTrunkEntry 1.3.6.1.1
An entry in the snTrunkTable indicates the configuration on a specified Trunk port membership.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SnTrunkEntry  

snTrunkIndex 1.3.6.1.1.1
The number of the trunk entries can be configured.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..64  

snTrunkPortMask 1.3.6.1.1.2
Trunk membership of the Switch.
Status: mandatory Access: read-write
OBJECT-TYPE    
  PortMask  

snTrunkType 1.3.6.1.1.3
The trunk connection type which specifies what device the trunk ports are connected to.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER switch(1), server(2)  

snMSTrunkTable 1.3.6.2
A table contains the configuration of port members of multi-slot trunk groups.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SnMSTrunkEntry

snMSTrunkEntry 1.3.6.2.1
An entry of the snMSTrunkTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SnMSTrunkEntry  

snMSTrunkPortIndex 1.3.6.2.1.1
The primary port of a trunk group. For module with Gig ports, primary port is port 1, 3, 5, 7. For module with 10/100 ports, primary port is port 1, 5, 9, 13, 17, 21.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

snMSTrunkPortList 1.3.6.2.1.2
A list of port indices which are the port membership of a trunk group. Each port index is a 16-bit integer in big endian order. The first port index must be the primary port index.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

snMSTrunkType 1.3.6.2.1.3
The trunk connection type which specifies what device the trunk ports are connected to.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER switch(1), server(2)  

snMSTrunkRowStatus 1.3.6.2.1.4
To create or delete a table entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER invalid(1), valid(2), delete(3), create(4), modify(5)  

snSwSummaryMode 1.3.7.1
The Switch Group Configuration Summary is configured either enabled or disabled and the default is disabled mode. enabled(1)...........activate Switch Configuration Summary. disabled(0)..........no Switch Configuration Summary.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

snDhcpGatewayListTable 1.3.8.1
A table of DHCP gateway list of addresses.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SnDhcpGatewayListEntry

snDhcpGatewayListEntry 1.3.8.1.1
An entry in the IP Port Address table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SnDhcpGatewayListEntry  

snDhcpGatewayListId 1.3.8.1.1.1
The ID for a DHCP gateway list entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..32  

snDhcpGatewayListAddrList 1.3.8.1.1.2
The DHCP gateway address list for each DHCP gateway list ID. This list contains 1 to 8 IP addresses represented by octet string.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(4..32)  

snDhcpGatewayListRowStatus 1.3.8.1.1.3
This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row or modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row other(1)....some other case valid(2)....the row exists and is valid
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), valid(2), delete(3), create(4)  

snDnsDomainName 1.3.9.1
DNS Domain Name string.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..80)  

snDnsGatewayIpAddrList 1.3.9.2
The DNS Gateway IP address list. This list contains 4 IP addresses represented by octet string.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(16)  

snMacFilterTable 1.3.10.1
MAC filter table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SnMacFilterEntry

snMacFilterEntry 1.3.10.1.1
An entry in the MAC filter table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SnMacFilterEntry  

snMacFilterIndex 1.3.10.1.1.1
The table index for a filter entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

snMacFilterAction 1.3.10.1.1.2
Action to take if the Mac packet match with this filter.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER deny(0), permit(1)  

snMacFilterSourceMac 1.3.10.1.1.3
Source MAC address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  MacAddress  

snMacFilterSourceMask 1.3.10.1.1.4
Source MAC subnet mask.
Status: mandatory Access: read-write
OBJECT-TYPE    
  MacAddress  

snMacFilterDestMac 1.3.10.1.1.5
Destination MAC address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  MacAddress  

snMacFilterDestMask 1.3.10.1.1.6
Destination MAC subnet mask.
Status: mandatory Access: read-write
OBJECT-TYPE    
  MacAddress  

snMacFilterOperator 1.3.10.1.1.7
Type of comparison to perform.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER equal(0), notEqual(1), less(2), greater(3)  

snMacFilterFrameType 1.3.10.1.1.8
Frame Type: ethernet-type, LLC and SNAP types
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER notUsed(0), ethernet(1), llc(2), snap(3)  

snMacFilterFrameTypeNum 1.3.10.1.1.9
Frame Type Number. 0 means NA
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

snMacFilterRowStatus 1.3.10.1.1.10
This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER invalid(1), valid(2), delete(3), create(4), modify(5)  

snMacFilterPortAccessTable 1.3.10.2
MAC Filter port access table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SnMacFilterPortAccessEntry

snMacFilterPortAccessEntry 1.3.10.2.1
An entry in the MAC Filter Port access table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SnMacFilterPortAccessEntry  

snMacFilterPortAccessPortIndex 1.3.10.2.1.1
The port index. For FastIron/NetIron products, port index value is from 1 to 42 For BigIron products, port index is an encoded number: The bit 0 to bit 7: port number. The bit 8 to bit 11: slot number. For virtual router interface, slot number is 15, port number is the virtual router port from 1 to 60. Therefore, port index value for BigIron is from 257 to 3900.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..3900  

snMacFilterPortAccessFilters 1.3.10.2.1.2
1st octet correspond to 1st filter number and so on.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

snMacFilterPortAccessRowStatus 1.3.10.2.1.3
This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER invalid(1), valid(2), delete(3), create(4)  

snNTPGeneral 1.3.11.1
OBJECT IDENTIFIER    

snNTPPollInterval 1.3.11.1.1
Interval specifies how often to poll the NTP server. Each unit is one second.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

snNTPTimeZone 1.3.11.1.2
Time zone.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER alaska(0), aleutian(1), arizona(2), central(3), eastIndiana(4), eastern(5), hawaii(6), michigan(7), mountain(8), pacific(9), samoa(10), gmtPlus12(11), gmtPlus11(12), gmtPlus10(13), gmtPlus9(14), gmtPlus8(15), gmtPlus7(16), gmtPlus6(17), gmtPlus5(18), gmtPlus4(19), gmtPlus3(20), gmtPlus2(21), gmtPlus1(22), gmt(23), gmtMinus1(24), gmtMinus2(25), gmtMinus3(26), gmtMinus4(27), gmtMinus5(28), gmtMinus6(29), gmtMinus7(30), gmtMinus8(31), gmtMinus9(32), gmtMinus10(33), gmtMinus11(34), gmtMinus12(35)  

snNTPSummerTimeEnable 1.3.11.1.3
Enable/Disable daylight saving time. This enables daylight saving time for time/date starting 02:00:00 of first Sunday in April and ending 02:00:00 of last Sunday in October every year.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

snNTPSystemClock 1.3.11.1.4
System clock, in the following format: octet 0: seconds after the minute [0-60] octet 1: minutes after the hour [0-59] octet 2: hours since midnight [0-23] octet 3: day of the month [1-31] octet 4: months since January [0-11] octet 5: years since 1900 octet 6: days since Sunday [0-6] Setting this object requires valid value in octets 0 to 5, and zero in octet 6. System clock can be disabled by setting zero to all octets.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(7)  

snNTPSync 1.3.11.1.5
Initiate time synchronization to the NTP servers. For set operation, only 'synchronize(2)' is accepted. For get operation, always return 'other(1)'.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), synchronize(2)  

snNTPServerTable 1.3.11.2
NTP (Network Time Protocol) server table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SnNTPServerEntry

snNTPServerEntry 1.3.11.2.1
An entry in the NTP server table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SnNTPServerEntry  

snNTPServerIp 1.3.11.2.1.1
NTP server IP address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

snNTPServerVersion 1.3.11.2.1.2
NTP server version.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..4  

snNTPServerRowStatus 1.3.11.2.1.3
To create or delete a NTP server table entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), valid(2), delete(3), create(4)  

snRadiusGeneral 1.3.12.1
OBJECT IDENTIFIER    

snRadiusSNMPAccess 1.3.12.1.1
Indicate whether Radius group MIB obejcts can be accessed by SNMP manager. If value is disabled, all Radius group MIB objects return 'general error'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

snRadiusEnableTelnetAuth 1.3.12.1.2
Enable/Disable telnet authentication specified by 'snRadiusLoginMethod'.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

snRadiusRetransmit 1.3.12.1.3
The number of authentication query retransmissions to the Radius server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..5  

snRadiusTimeOut 1.3.12.1.4
Interval specifies how long to wait for authentication reply from the Radius server, each unit is one second.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..15  

snRadiusDeadTime 1.3.12.1.5
Interval specifies Radius server dead time, each unit is one minute.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..5  

snRadiusKey 1.3.12.1.6
Authentication key displayed as encrypted text.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

snRadiusLoginMethod 1.3.12.1.7
A sequence of authentication methods. Each octet represents a method to authenticate the user login process. Each octet has the following enumeration value: enable(1) - authenticate by command line interface enable password radius(2) - authenticate by requesting radius server local(3) - authenticate by local user account table line(4) - authenticate by telnet password tacplus(5) - authenticate by requesting tacplus server none(6) - do not authenticate tacacs(7) - authenticate by requesting tacacs server Setting a zero length octet string invalidates all previous authentication methods.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..7)  

snRadiusEnableMethod 1.3.12.1.8
A sequence of authentication methods. Each octet represents a method to authenticate the user entering priviledge mode of the command line interface. Each octet has the following enumeration value: enable(1) - authenticate by command line interface enable password radius(2) - authenticate by requesting radius server local(3) - authenticate by local user account table line(4) - authenticate by telnet password tacplus(5) - authenticate by requesting tacplus server none(6) - do not authenticate tacacs(7) - authenticate by requesting tacacs server Setting a zero length octet string invalidates all previous authentication methods.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..7)  

snRadiusWebServerMethod 1.3.12.1.9
A sequence of authentication methods. Each octet represents a method to authenticate the user accessing the web-server. Each octet has the following enumeration value: enable(1) - authenticate by command line interface enable password radius(2) - authenticate by requesting radius server local(3) - authenticate by local user account table line(4) - authenticate by telnet password tacplus(5) - authenticate by requesting tacplus server none(6) - do not authenticate tacacs(7) - authenticate by requesting tacacs server Setting a zero length octet string invalidates all previous authentication methods.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..7)  

snRadiusSNMPServerMethod 1.3.12.1.10
A sequence of authentication methods. Each octet represents a method to authenticate the user accessing the snmp-server. Each octet has the following enumeration value: enable(1) - authenticate by command line interface enable password radius(2) - authenticate by requesting radius server local(3) - authenticate by local user account table line(4) - authenticate by telnet password tacplus(5) - authenticate by requesting tacplus server none(6) - do not authenticate tacacs(7) - authenticate by requesting tacacs server Setting a zero length octet string invalidates all previous authentication methods.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..7)  

snRadiusServerTable 1.3.12.2
Radius server table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SnRadiusServerEntry

snRadiusServerEntry 1.3.12.2.1
An entry in the Radius server table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SnRadiusServerEntry  

snRadiusServerIp 1.3.12.2.1.1
Radius server IP address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

snRadiusServerAuthPort 1.3.12.2.1.2
Authentication UDP port number.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

snRadiusServerAcctPort 1.3.12.2.1.3
Account UDP port number.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

snRadiusServerRowStatus 1.3.12.2.1.4
To create or delete a Radius server table entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), valid(2), delete(3), create(4)  

snRadiusServerRowKey 1.3.12.2.1.5
Authentication key displayed as encrypted text.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

snRadiusServerUsage 1.3.12.2.1.6
To allow this server to be dedicated for a particular AAA activity.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER default(1), authentication-only(2), authorization-only(3), accounting-only(4)  

snTacacsGeneral 1.3.13.1
OBJECT IDENTIFIER    

snTacacsRetransmit 1.3.13.1.1
The number of authentication query retransmissions to the Tacacs server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..5  

snTacacsTimeOut 1.3.13.1.2
Interval specifies how long to wait for authentication reply from the Tacacs server, each unit is one second.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..15  

snTacacsDeadTime 1.3.13.1.3
Interval specifies Tacacs server dead time, each unit is one minute.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..5  

snTacacsKey 1.3.13.1.4
Authentication key displayed as encrypted text.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

snTacacsSNMPAccess 1.3.13.1.5
Indicate whether Tacacs group MIB obejcts can be accessed by SNMP manager. If value is disabled, all Tacacs group MIB objects return 'general error'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

snTacacsServerTable 1.3.13.2
Tacacs server table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SnTacacsServerEntry

snTacacsServerEntry 1.3.13.2.1
An entry in the Tacacs server table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SnTacacsServerEntry  

snTacacsServerIp 1.3.13.2.1.1
Tacacs server IP address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

snTacacsServerAuthPort 1.3.13.2.1.2
Authentication UDP port number.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

snTacacsServerRowStatus 1.3.13.2.1.3
To create or delete a Tacacs server table entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), valid(2), delete(3), create(4)  

snTacacsServerRowKey 1.3.13.2.1.4
Authentication key displayed as encrypted text.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

snTacacsServerUsage 1.3.13.2.1.5
To allow this server to be dedicated for a particular AAA activity.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER default(1), authentication-only(2), authorization-only(3), accounting-only(4)  

snQosProfileTable 1.3.14.1
A table contains the configuration of qos profile groups.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SnQosProfileEntry

snQosProfileEntry 1.3.14.1.1
An entry of the snQosProfileTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SnQosProfileEntry  

snQosProfileIndex 1.3.14.1.1.1
The table index of QOS Profile.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..4  

snQosProfileName 1.3.14.1.1.2
Qos Profile Name string.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

snQosProfileRequestedBandwidth 1.3.14.1.1.3
Qos Profile Requested Bandwidth.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..100  

snQosProfileCalculatedBandwidth 1.3.14.1.1.4
Qos Profile Calculated Bandwidth.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

snQosBindTable 1.3.14.2
A table contains the configuration of 802.1p to qos profile binding groups.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SnQosBindEntry

snQosBindEntry 1.3.14.2.1
An entry of the snQosBindTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SnQosBindEntry  

snQosBindIndex 1.3.14.2.1.1
The table index of QOS Bind.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..8  

snQosBindPriority 1.3.14.2.1.2
QOS bind priority.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

snQosBindProfileIndex 1.3.14.2.1.3
QOS Bind Profile Index. This is pointer to the index of snQosProfile Table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..4  

snAuthentication 1.3.15.1
OBJECT IDENTIFIER    

snAuthorization 1.3.15.2
OBJECT IDENTIFIER    

snAccounting 1.3.15.3
OBJECT IDENTIFIER    

snAuthorizationCommandMethods 1.3.15.2.1
A sequence of authorization methods. Each octet represents a method to authorize the user command. Each octet has the following value: radius(2) - authorize by requesting radius server tacplus(5) - authorize by requesting tacplus server none(6) - skip authorization Setting a zero length octet string invalidates all previous authorization methods.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..3)  

snAuthorizationCommandLevel 1.3.15.2.2
Commands, which are equal to and less than the specified command level here needs to be authorized. Possible enumeration values: 0 - Privilege level 0 4 - Privilege level 4 5 - Privilege level 5.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER level0(0), level4(4), level5(5)  

snAuthorizationExec 1.3.15.2.3
A sequence of exec authorization methods. Each octet represents a method for telnet or SSH login authorization. Each octet has the following enumeration value: radius(2) - send exec authorization request to radius server tacplus(5) - send exec authorization request to tacplus server none(6) - no exec authorization Setting a zero length octet string invalidates all authorization methods.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..3)  

snAccountingCommandMethods 1.3.15.3.1
A sequence of accounting methods. Each octet represents a method to account for the user command. Each octet has the following enumeration value: radius(2) - send accounting info to radius server tacplus(5) - send accounting info to tacplus server none(6) - skip accounting Setting a zero length octet string invalidates all previous accounting methods.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..3)  

snAccountingCommandLevel 1.3.15.3.2
Commands, which are equal to and less than the specified command level here will be accounted. Possible enumeration values: level0 - Privilege level 0 level4 - Privilege level 4 level5 - Privilege level 5.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER level0(0), level4(4), level5(5)  

snAccountingExec 1.3.15.3.3
A sequence of accounting methods. Each octet represents a method for telnet or SSH login accounting. Each octet has the following enumeration value: radius(2) - send accounting info to radius server tacplus(5) - send accounting info to tacplus server none(6) - skip accounting Setting a zero length octet string invalidates all previous accounting methods.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..3)  

snAccountingSystem 1.3.15.3.4
A sequence of accounting methods. Each octet represents a method to account for the system related events. Each octet has the following enumeration value: radius(2) - send accounting info to radius server tacplus(5) - send accounting info to tacplus server none(6) - skip accounting Setting a zero length octet string invalidates all previous accounting methods.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..3)  

snNetFlowGlb 1.3.18.1
OBJECT IDENTIFIER    

snNetFlowGblEnable 1.3.18.1.1
Enable/disable NetFlow export operation.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

snNetFlowGblVersion 1.3.18.1.2
NetFlow export version.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER version1(1), version5(5)  

snNetFlowGblProtocolDisable 1.3.18.1.3
bit 0 - other, disable all protocols export except UDP and TCP bit 1 - tcp, disable TCP protocol export bit 2 - udp, disable UDP protocol export
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

snNetFlowGblActiveTimeout 1.3.18.1.4
Maximum time an active flow can be in the NetFlow cache (minutes: 1..60)
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

snNetFlowGblInactiveTimeout 1.3.18.1.5
Maximum time an inactive flow can be in the NetFlow cache (seconds: 10..600)
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

snNetFlowCollectorTable 1.3.18.2
A table of each NetFlow collector information.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SnNetFlowCollectorEntry

snNetFlowCollectorEntry 1.3.18.2.1
A row in the NetFlow collector table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SnNetFlowCollectorEntry  

snNetFlowCollectorIndex 1.3.18.2.1.1
The index to the NetFlow collector table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..10  

snNetFlowCollectorIp 1.3.18.2.1.2
The NetFlow collector ip address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

snNetFlowCollectorUdpPort 1.3.18.2.1.3
The NetFlow collector UDP port number.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

snNetFlowCollectorSourceInterface 1.3.18.2.1.4
The ifIndex value to specify source port to export NetFlow packet. Value 0 to indicate default outgoing port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

snNetFlowCollectorRowStatus 1.3.18.2.1.5
To create or delete a NetFlow collector table entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), valid(2), delete(3), create(4)  

snNetFlowAggregationTable 1.3.18.3
A table of each NetFlow aggregation scheme information.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SnNetFlowAggregationEntry

snNetFlowAggregationEntry 1.3.18.3.1
A row in the NetFlow Aggregation table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SnNetFlowAggregationEntry  

snNetFlowAggregationIndex 1.3.18.3.1.1
The Aggregation scheme ID
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER as(1), protocolPort(2), destPrefix(3), sourcePrefix(4), prefix(5)  

snNetFlowAggregationIp 1.3.18.3.1.2
The NetFlow aggregation collector ip address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

snNetFlowAggregationUdpPort 1.3.18.3.1.3
The NetFlow aggregation collector UDP port number.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

snNetFlowAggregationSourceInterface 1.3.18.3.1.4
The ifIndex value to specify source port to export NetFlow aggregation packet. Value 0 to indicate default outgoing port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

snNetFlowAggregationNumberOfCacheEntries 1.3.18.3.1.5
Number of cache entries for aggregation scheme
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

snNetFlowAggregationActiveTimeout 1.3.18.3.1.6
Maximum time an active flow can be in the aggregation cache
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

snNetFlowAggregationInactiveTimeout 1.3.18.3.1.7
Maximum time an inactive flow can be in the aggregation cache
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

snNetFlowAggregationEnable 1.3.18.3.1.8
Enable/disable NetFlow aggregation for this aggregation scheme.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

snNetFlowAggregationRowStatus 1.3.18.3.1.9
To create or delete a NetFlow collector table entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), valid(2), delete(3), create(4)  

snNetFlowIfTable 1.3.18.4
A list of interface entries. The number of entries is given by the value of ifNumber.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SnNetFlowIfEntry

snNetFlowIfEntry 1.3.18.4.1
Entry containing the type of switching performed on that interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SnNetFlowIfEntry  

snNetFlowIfIndex 1.3.18.4.1.1
A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..65536  

snNetFlowIfFlowSwitching 1.3.18.4.1.2
To enable/disable flow switching in a particular interface: disable (0) - no flow switching enable (1) - flow switching
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

snSFlowGlb 1.3.19.1
OBJECT IDENTIFIER    

snSflowCollectorTable 1.3.19.2
Table of all but first sFlow collectors. The first collector can be configured using sFlowTable in RFC 3176. The RFC cannot be used to configure more than one sFlow collectors. This table has been created to fill this gap.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SnSflowCollectorEntry

snSflowCollectorEntry 1.3.19.2.1
A row in the sFlow collector table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SnSflowCollectorEntry  

snSflowCollectorIndex 1.3.19.2.1.1
The index to the sFlow collector table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

snSflowCollectorIP 1.3.19.2.1.2
The sFlow collector ip address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

snSflowCollectorUDPPort 1.3.19.2.1.3
The sFlow collector UDP port number.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

snSflowCollectorRowStatus 1.3.19.2.1.4
To create, update or delete a SFlow collector table entry. If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row other(1)....some other case valid(2)....the row exists and is valid
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noSuch(0), other(1), valid(2), delete(3), create(4), modify(5)  

snFdpMIBObjects 1.3.20.1
OBJECT IDENTIFIER    

snFdpInterface 1.3.20.1.1
OBJECT IDENTIFIER    

snFdpCache 1.3.20.1.2
OBJECT IDENTIFIER    

snFdpGlobal 1.3.20.1.3
OBJECT IDENTIFIER    

snFdpCachedAddr 1.3.20.1.4
OBJECT IDENTIFIER    

snFdpInterfaceTable 1.3.20.1.1.1
Status of FDP on the device's interfaces.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FdpInterfaceEntry

snFdpInterfaceEntry 1.3.20.1.1.1.1
An entry in the snFdpInterfaceTable, having the status of FDP on an interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FdpInterfaceEntry  

snFdpInterfaceIfIndex 1.3.20.1.1.1.1.1
ifIndex value of the local interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

snFdpInterfaceFdpEnable 1.3.20.1.1.1.1.2
The flag, whether the Foundry Discovery Protocol is currently running on this interface. It has no effect when FDP is disabled (snFdpGlobalRun = FALSE).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER false(0), true(1)  

snFdpInterfaceCdpEnable 1.3.20.1.1.1.1.3
The flag, whether the Cisco Discovery Protocol is currently running on this interface. It has no effect when CDP is disabled (snCdpGlobalRun = FALSE).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER false(0), true(1)  

snFdpCacheTable 1.3.20.1.2.1
The table for the cached information obtained via receiving FDP/CDP messages.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FdpCacheEntry

snFdpCacheEntry 1.3.20.1.2.1.1
An entry in the snFdpCacheTable, having the information received via FDP/CDP on one interface from one device. Entries appear when a FDP/CDP advertisement is received from a neighbor device. Entries disappear when FDP/CDP is disabled on the interface, or globally.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FdpCacheEntry  

snFdpCacheIfIndex 1.3.20.1.2.1.1.1
ifIndex value of the local interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

snFdpCacheDeviceIndex 1.3.20.1.2.1.1.2
Identification of a device, which sent FDP/CDP messages
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

snFdpCacheDeviceId 1.3.20.1.2.1.1.3
The Device-ID string as reported in the most recent FDP/CDP message. The zero-length string indicates no Device-ID field (TLV) was reported in the most recent FDP/CDP message.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

snFdpCacheAddressType 1.3.20.1.2.1.1.4
An indication of the type of address contained in the corresponding instance of snFdpCacheAddress.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ip(1), ipx(2), appletalk(3)  

snFdpCacheAddress 1.3.20.1.2.1.1.5
The (first) network-layer address of the device as reported in the most recent FDP/CDP message in the following format: IP address: 4 octets, ip(1) IPX address: 10 octets, ipx(2) First 4-octet as the network number Second 6-octet as the host number Appletalk address: 3 octets, appletalk(3) First 2-octet as the network number Second 1-octet as the host number
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

snFdpCacheVersion 1.3.20.1.2.1.1.6
Version string as reported in the most recent FDP/CDP message.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

snFdpCacheDevicePort 1.3.20.1.2.1.1.7
The Port-ID string as reported in the most recent FDP/CDP message. This will typically be the value of the ifName object (e.g., Ethernet0). The zero-length string indicates no Port-ID field (TLV) was reported in the most recent FDP/CDP message.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

snFdpCachePlatform 1.3.20.1.2.1.1.8
The Device's Hardware Platform as reported in the most recent FDP/CDP message. The zero-length string indicates that no Platform field (TLV) was reported in the most recent FDP/CDP message.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

snFdpCacheCapabilities 1.3.20.1.2.1.1.9
The Device's Functional Capabilities as reported in the most recent FDP/CDP message.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

snFdpCacheVendorId 1.3.20.1.2.1.1.10
Indicates the entry received by either FDP or CDP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER fdp(1), cdp(2)  

snFdpCacheIsAggregateVlan 1.3.20.1.2.1.1.11
Neighbor device is in aggregated-vlan.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER false(0), true(1)  

snFdpCacheTagType 1.3.20.1.2.1.1.12
Neighbor device tag-type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

snFdpCachePortVlanMask 1.3.20.1.2.1.1.13
Neighbor device port VLAN masks in 512-byte octet string.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

snFdpCachePortTagMode 1.3.20.1.2.1.1.14
Neighbor device port tag mode
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER untagged(1), tagged(2), dual(3)  

snFdpCacheDefaultTrafficeVlanIdForDualMode 1.3.20.1.2.1.1.15
Default traffic vlan id for neighbor device dual-mode port
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

snFdpGlobalRun 1.3.20.1.3.1
The flag, whether the Foundry Discovery Protocol is currently running. FDP entries in snFdpCacheTable are deleted when FDP is disabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER false(0), true(1)  

snFdpGlobalMessageInterval 1.3.20.1.3.2
The interval at which FDP messages are to be generated. The default value is 60 seconds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 5..900  

snFdpGlobalHoldTime 1.3.20.1.3.3
The time for the receiving device holds FDP message. The default value is 180 seconds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 10..255  

snFdpGlobalCdpRun 1.3.20.1.3.4
An indication of whether the Cisco Discovery Protocol is currently running. CDP entries in snFdpCacheTable are deleted when CDP is disabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER false(0), true(1)  

snFdpCachedAddressTable 1.3.20.1.4.1
Cached address table from receiving FDP/CDP messages.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FdpCachedAddressEntry

snFdpCachedAddressEntry 1.3.20.1.4.1.1
An entry (conceptual row) in the snFdpCacheAddressTable, containing one cached address from FDP/CDP messages.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FdpCachedAddressEntry  

snFdpCachedAddrIfIndex 1.3.20.1.4.1.1.1
The ifIndex value of the local interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

snFdpCachedAddrDeviceIndex 1.3.20.1.4.1.1.2
A unique vlaue for each device from which FDP/CDP messages are being received.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

snFdpCachedAddrDeviceAddrEntryIndex 1.3.20.1.4.1.1.3
A unique vlaue for address entry in device from which FDP/CDP messages are being received.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

snFdpCachedAddrType 1.3.20.1.4.1.1.4
An indication of the type of address contained in the corresponding instance of snFdpCacheAddrValue.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ip(1), ipx(2), appletalk(3)  

snFdpCachedAddrValue 1.3.20.1.4.1.1.5
The network-layer address of the device SNMP-agent as reported in the most recent FDP/CDP message in the following format: IP address: 4 octets, ip(1) IPX address: 10 octets, ipx(2) First 4-octet as the network number Second 6-octet as the host number Appletalk address: 3 octets, appletalk(3) First 2-octet as the network number Second 1-octet as the host number
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING