HIRSCHMANN-MMP4-ROUTING-MIB

File: HIRSCHMANN-MMP4-ROUTING-MIB.mib (84987 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC OSPF-MIB
RIPv2-MIB HIRSCHMANN-MMP4-BASICL2-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE IpAddress
Unsigned32 Integer32 Counter32
TimeTicks Gauge32 RowStatus
TruthValue MacAddress ospfIfEntry
ospfVirtIfEntry rip2IfConfEntry hmPlatform4

Defined Types

HmAgentSwitchArpEntry  
SEQUENCE    
  hmAgentSwitchArpAge TimeTicks
  hmAgentSwitchArpIpAddress IpAddress
  hmAgentSwitchArpMacAddress MacAddress
  hmAgentSwitchArpInterface Integer32
  hmAgentSwitchArpType INTEGER
  hmAgentSwitchArpStatus RowStatus

HmAgentSwitchIpInterfaceEntry  
SEQUENCE    
  hmAgentSwitchIpInterfaceIfIndex Integer32
  hmAgentSwitchIpInterfaceIpAddress IpAddress
  hmAgentSwitchIpInterfaceNetMask IpAddress
  hmAgentSwitchIpInterfaceClearIp INTEGER
  hmAgentSwitchIpInterfaceRoutingMode INTEGER
  hmAgentSwitchIpInterfaceProxyARPMode INTEGER
  hmAgentSwitchIpInterfaceMtuValue Unsigned32
  hmAgentSwitchIpInterfaceSlotNum Integer32
  hmAgentSwitchIpInterfacePortNum Integer32
  hmAgentSwitchIpInterfaceNetdirectedBCMode INTEGER

HmAgentSwitchIpRouterDiscoveryEntry  
SEQUENCE    
  hmAgentSwitchIpRouterDiscoveryIfIndex Integer32
  hmAgentSwitchIpRouterDiscoveryAdvertiseMode INTEGER
  hmAgentSwitchIpRouterDiscoveryMaxAdvertisementInterval Integer32
  hmAgentSwitchIpRouterDiscoveryMinAdvertisementInterval Integer32
  hmAgentSwitchIpRouterDiscoveryAdvertisementLifetime Integer32
  hmAgentSwitchIpRouterDiscoveryPreferenceLevel Integer32
  hmAgentSwitchIpRouterDiscoveryAdvertisementAddress IpAddress

HmAgentSwitchIpVlanEntry  
SEQUENCE    
  hmAgentSwitchIpVlanId Integer32
  hmAgentSwitchIpVlanIfIndex Integer32
  hmAgentSwitchIpVlanRoutingStatus RowStatus

HmAgentSwitchSecondaryAddressEntry  
SEQUENCE    
  hmAgentSwitchSecondaryIpAddress IpAddress
  hmAgentSwitchSecondaryNetMask IpAddress
  hmAgentSwitchSecondaryStatus RowStatus

HmAgentSwitchIpRoutePreferenceEntry  
SEQUENCE    
  hmAgentSwitchIpRoutePreferenceSource INTEGER
  hmAgentSwitchIpRoutePreferenceValue Integer32

HmAgentSwitchIpRouteStaticEntry  
SEQUENCE    
  hmAgentSwitchIpRouteStaticDestination IpAddress
  hmAgentSwitchIpRouteStaticDestinationMask IpAddress
  hmAgentSwitchIpRouteStaticNextHop IpAddress
  hmAgentSwitchIpRouteStaticPreference Integer32
  hmAgentSwitchIpRouteStaticStatus RowStatus
  hmAgentSwitchIpRouteStaticTrackId Integer32

HmAgentRipRouteRedistEntry  
SEQUENCE    
  hmAgentRipRouteRedistSource INTEGER
  hmAgentRipRouteRedistMode INTEGER
  hmAgentRipRouteRedistMetric Integer32
  hmAgentRipRouteRedistMetricConfigured TruthValue
  hmAgentRipRouteRedistMatchInternal INTEGER
  hmAgentRipRouteRedistMatchExternal1 INTEGER
  hmAgentRipRouteRedistMatchExternal2 INTEGER
  hmAgentRipRouteRedistMatchNSSAExternal1 INTEGER
  hmAgentRipRouteRedistMatchNSSAExternal2 INTEGER
  hmAgentRipRouteRedistDistList Unsigned32
  hmAgentRipRouteRedistDistListConfigured TruthValue

HmAgentRip2IfConfEntry  
SEQUENCE    
  hmAgentRip2IfConfAuthKeyId Integer32

HmAgentRip2InterfaceEntry  
SEQUENCE    
  hmAgentRip2InterfaceIfIndex Integer32
  hmAgentRip2InterfaceAuthType INTEGER
  hmAgentRip2InterfaceAuthKey OCTET STRING
  hmAgentRip2InterfaceAuthKeyId Integer32
  hmAgentRip2InterfaceSendVersion INTEGER
  hmAgentRip2InterfaceReceiveVersion INTEGER
  hmAgentRip2InterfaceAdminState INTEGER
  hmAgentRip2RcvBadPackets Counter32
  hmAgentRip2RcvBadRoutes Counter32
  hmAgentRip2SentUpdates Counter32

HmAgentOspfRouteRedistEntry  
SEQUENCE    
  hmAgentOspfRouteRedistSource INTEGER
  hmAgentOspfRouteRedistMode INTEGER
  hmAgentOspfRouteRedistMetric Integer32
  hmAgentOspfRouteRedistMetricConfigured TruthValue
  hmAgentOspfRouteRedistMetricType INTEGER
  hmAgentOspfRouteRedistTag Unsigned32
  hmAgentOspfRouteRedistSubnets TruthValue
  hmAgentOspfRouteRedistDistList Unsigned32
  hmAgentOspfRouteRedistDistListConfigured TruthValue

HmAgentOspfIfEntry  
SEQUENCE    
  hmAgentOspfIfAuthKeyId Integer32
  hmAgentOspfIfIpMtuIgnoreFlag INTEGER

HmAgentOspfVirtIfEntry  
SEQUENCE    
  hmAgentOspfVirtIfAuthKeyId Integer32

HmVrrpTrackingEntry  
SEQUENCE    
  hmVrrpTrackIfIndex Integer32
  hmVrrpTrackVrid Integer32
  hmVrrpTrackId Integer32
  hmVrrpTrackDecrement Integer32
  hmVrrpTrackOperStatus INTEGER
  hmVrrpTrackRowStatus RowStatus

HmVrrpExtEntry  
SEQUENCE    
  hmVrrpExtIfIndex Integer32
  hmVrrpExtVrid Integer32
  hmVrrpExtDomainId Integer32
  hmVrrpExtDomainRole INTEGER
  hmVrrpExtDomainStatus INTEGER
  hmVrrpExtAdvertAddress IpAddress
  hmVrrpExtAdvertTimer Integer32
  hmVrrpExtOperPriority Integer32
  hmVrrpExtNotifyAddress IpAddress
  hmVrrpExtNotifyLinkdown INTEGER
  hmVrrpExtPreemptionDelay Integer32

HmVrrpDomainEntry  
SEQUENCE    
  hmVrrpDomainId Integer32
  hmVrrpDomainMemberSendAdv INTEGER
  hmVrrpDomainStatus INTEGER
  hmVrrpDomainSupervisorIfIndex Integer32
  hmVrrpDomainSupervisorVrid Integer32
  hmVrrpDomainOperPriority Integer32
  hmVrrpDomainSupervisorOperState INTEGER

Defined Values

hmPlatform4Routing 1.3.6.1.4.1.248.15.2
The Hirschmann Private Platform4 Routing MIB definitions for Platform devices.
MODULE-IDENTITY    

hmAgentSwitchArpGroup 1.3.6.1.4.1.248.15.2.1
OBJECT IDENTIFIER    

hmAgentSwitchArpAgeoutTime 1.3.6.1.4.1.248.15.2.1.1
Configures the ARP entry ageout time in seconds. Allowable range: 15-21600
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 15..21600  

hmAgentSwitchArpResponseTime 1.3.6.1.4.1.248.15.2.1.2
Configures the ARP request response timeout in seconds. Allowable range: 1-10
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..10  

hmAgentSwitchArpMaxRetries 1.3.6.1.4.1.248.15.2.1.3
Configures the ARP count of maximum request for retries. Allowable range: 0-10
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..10  

hmAgentSwitchArpCacheSize 1.3.6.1.4.1.248.15.2.1.4
Configures the ARP maximum number of entries in the cache. Allowable range is platform-specific.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hmAgentSwitchArpDynamicRenew 1.3.6.1.4.1.248.15.2.1.5
This indicates the current setting of ARP dynamic renew mode.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentSwitchArpTotalEntryCountCurrent 1.3.6.1.4.1.248.15.2.1.6
Current number of entries in the ARP cache.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hmAgentSwitchArpTotalEntryCountPeak 1.3.6.1.4.1.248.15.2.1.7
Peak number of entries recorded in the ARP cache over time. This value is restarted whenever the ARP cache size is changed.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hmAgentSwitchArpStaticEntryCountCurrent 1.3.6.1.4.1.248.15.2.1.8
Current number of configured static ARP entries.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hmAgentSwitchArpStaticEntryCountMax 1.3.6.1.4.1.248.15.2.1.9
Maximum number of configurable static ARP entries.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hmAgentSwitchArpTable 1.3.6.1.4.1.248.15.2.1.10
This table augments the MIB-II ipNetToMediaTable by providing per-interface ARP entry information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmAgentSwitchArpEntry

hmAgentSwitchArpEntry 1.3.6.1.4.1.248.15.2.1.10.1
The entry of the hmAgentSwitchArpTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  HmAgentSwitchArpEntry  

hmAgentSwitchArpAge 1.3.6.1.4.1.248.15.2.1.10.1.1
This defines the time (in seconds) since the ARP entry was last refreshed. This value is 0 for ARP entries of type local(1) or static(3), since these entries are not subject to aging.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

hmAgentSwitchArpIpAddress 1.3.6.1.4.1.248.15.2.1.10.1.2
The IP Address assigned to each interface.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

hmAgentSwitchArpMacAddress 1.3.6.1.4.1.248.15.2.1.10.1.3
The hardware MAX Address that each interface maps to.
Status: current Access: read-create
OBJECT-TYPE    
  MacAddress  

hmAgentSwitchArpInterface 1.3.6.1.4.1.248.15.2.1.10.1.4
The Associated IfIndex which identified the ARP Entry.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hmAgentSwitchArpType 1.3.6.1.4.1.248.15.2.1.10.1.5
The type of ARP entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER local(1), gateway(2), static(3), dynamic(4)  

hmAgentSwitchArpStatus 1.3.6.1.4.1.248.15.2.1.10.1.6
The status of this ARP entry. Setting this object destroy will remove the entry.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

hmAgentSwitchArpSparseLearn 1.3.6.1.4.1.248.15.2.1.11
This indicates the current setting of ARP sparse learn mode.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentSwitchIpGroup 1.3.6.1.4.1.248.15.2.2
OBJECT IDENTIFIER    

hmAgentSwitchIpRoutingMode 1.3.6.1.4.1.248.15.2.2.1
Administratively enables/disables routing on the switch.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentSwitchIpVRRPMode 1.3.6.1.4.1.248.15.2.2.2
Administratively enables/disables VRRP on the switch.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentSwitchIpInterfaceTable 1.3.6.1.4.1.248.15.2.2.3
The hmAgentSwitchIpInterfaceTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmAgentSwitchIpInterfaceEntry

hmAgentSwitchIpInterfaceEntry 1.3.6.1.4.1.248.15.2.2.3.1
The entry of the hmAgentSwitchIpInterfaceTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  HmAgentSwitchIpInterfaceEntry  

hmAgentSwitchIpInterfaceIfIndex 1.3.6.1.4.1.248.15.2.2.3.1.1
The IfIndex associated with this instance.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hmAgentSwitchIpInterfaceIpAddress 1.3.6.1.4.1.248.15.2.2.3.1.2
The IpAddress assigned to this interface. When setting this value, the value of hmAgentSwitchIpInterfaceNetMask must be set at the same time.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

hmAgentSwitchIpInterfaceNetMask 1.3.6.1.4.1.248.15.2.2.3.1.3
The NetMask assigned to this interface. When setting this value, the value of hmAgentSwitchIpInterfaceIpAddress must be set at the same time.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

hmAgentSwitchIpInterfaceClearIp 1.3.6.1.4.1.248.15.2.2.3.1.4
Sets the interface's primary IpAddress and NetMask back to 0.0.0.0. The primary ip address can be removed if and only if there are no configured secondary addresses.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentSwitchIpInterfaceRoutingMode 1.3.6.1.4.1.248.15.2.2.3.1.5
Enables or disables routing for this interface.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentSwitchIpInterfaceProxyARPMode 1.3.6.1.4.1.248.15.2.2.3.1.6
Enables or disables Proxy ARP for this interface.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentSwitchIpInterfaceMtuValue 1.3.6.1.4.1.248.15.2.2.3.1.7
Configures the MTU value for this interface. If the value returned is 0 this interface is not enabled for routing. It is not valid to set this value to 0 if routing is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0 | 68..9000  

hmAgentSwitchIpInterfaceSlotNum 1.3.6.1.4.1.248.15.2.2.3.1.8
The Slot Number associated with this instance.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hmAgentSwitchIpInterfacePortNum 1.3.6.1.4.1.248.15.2.2.3.1.9
The Port Number associated with this instance.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hmAgentSwitchIpInterfaceNetdirectedBCMode 1.3.6.1.4.1.248.15.2.2.3.1.10
Enables or disables netdirected broadcasts for this interface.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentSwitchIpRouterDiscoveryTable 1.3.6.1.4.1.248.15.2.2.4
There is no global administrative flag for router discovery. The global routing flag (hmAgentSwitchIpRoutingMode) will be used for this purpose. If routing is disabled, router discovery is disabled as well.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmAgentSwitchIpRouterDiscoveryEntry

hmAgentSwitchIpRouterDiscoveryEntry 1.3.6.1.4.1.248.15.2.2.4.1
The entry of the hmAgentSwitchIpRouterDiscoveryTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  HmAgentSwitchIpRouterDiscoveryEntry  

hmAgentSwitchIpRouterDiscoveryIfIndex 1.3.6.1.4.1.248.15.2.2.4.1.1
Interface Number to configure Router Discovery on.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hmAgentSwitchIpRouterDiscoveryAdvertiseMode 1.3.6.1.4.1.248.15.2.2.4.1.2
Enable or disable router discovery on the interface.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentSwitchIpRouterDiscoveryMaxAdvertisementInterval 1.3.6.1.4.1.248.15.2.2.4.1.3
Maximum time allowed between sending router advertisements from the interface.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 4..1800  

hmAgentSwitchIpRouterDiscoveryMinAdvertisementInterval 1.3.6.1.4.1.248.15.2.2.4.1.4
Minimum time allowed between sending router advertisements from the interface. This value must be less than or equal to hmAgentSwitchIpRouterDiscoveryMaxAdvertisementInterval.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 3..1800  

hmAgentSwitchIpRouterDiscoveryAdvertisementLifetime 1.3.6.1.4.1.248.15.2.2.4.1.5
Value of lifetime field of router advertsisement sent from the interface. This value must be greater than or equal to hmAgentSwitchIpRouterDiscoveryMaxAdvertisementInterval.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 4..9000  

hmAgentSwitchIpRouterDiscoveryPreferenceLevel 1.3.6.1.4.1.248.15.2.2.4.1.6
Preferability of the address as a default router address, related to other addresses on the same subnet. This is defined as the larger the number, the higher the preference.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hmAgentSwitchIpRouterDiscoveryAdvertisementAddress 1.3.6.1.4.1.248.15.2.2.4.1.7
Address used when sending router advertisements from the interface.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

hmAgentSwitchIpVlanTable 1.3.6.1.4.1.248.15.2.2.5
The hmAgentSwitchIpVlanTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmAgentSwitchIpVlanEntry

hmAgentSwitchIpVlanEntry 1.3.6.1.4.1.248.15.2.2.5.1
A Static VLAN for which routing can be enabled/disabled.
Status: current Access: not-accessible
OBJECT-TYPE    
  HmAgentSwitchIpVlanEntry  

hmAgentSwitchIpVlanId 1.3.6.1.4.1.248.15.2.2.5.1.1
The Vlan's Id.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hmAgentSwitchIpVlanIfIndex 1.3.6.1.4.1.248.15.2.2.5.1.2
The IfIndex associated with this VLAN.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hmAgentSwitchIpVlanRoutingStatus 1.3.6.1.4.1.248.15.2.2.5.1.3
Status of Routing mode per Vlan. active(1) - Vlan is enabled for routing createAndGo(4) - Adds Vlan entry for routing destroy(6) - Removes Vlan from routing
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hmAgentSwitchSecondaryAddressTable 1.3.6.1.4.1.248.15.2.2.6
Contains a list of secondary IP Addresses associated with an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmAgentSwitchSecondaryAddressEntry

hmAgentSwitchSecondaryAddressEntry 1.3.6.1.4.1.248.15.2.2.6.1
A secondary IP Address for a given interface. This IP Address must not conflict with the IP Address configured in the hmAgentSwitchIpInterfaceTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  HmAgentSwitchSecondaryAddressEntry  

hmAgentSwitchSecondaryIpAddress 1.3.6.1.4.1.248.15.2.2.6.1.1
The Secondary IP Address assigned to this interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

hmAgentSwitchSecondaryNetMask 1.3.6.1.4.1.248.15.2.2.6.1.2
The Secondary Net Mask assigned to this interface. This value must be set during creation, and can not be changed.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

hmAgentSwitchSecondaryStatus 1.3.6.1.4.1.248.15.2.2.6.1.3
Creates a new entry in the Secondary Address table. Allowed values are: createAndGo(4) - Creates an entry in this table, associating the address with a given interface. The hmAgentSwitchSecondaryNetMask object must be set during creation. destroy(6) - Removes the associated address from the interface.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hmAgentSwitchIpRoutePreferenceTable 1.3.6.1.4.1.248.15.2.2.7
This table contains the MIB objects required to configure the preferences/ administrative distances for the various routing protocols:
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmAgentSwitchIpRoutePreferenceEntry

hmAgentSwitchIpRoutePreferenceEntry 1.3.6.1.4.1.248.15.2.2.7.1
The entry of the hmAgentSwitchIpRoutePreferenceTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  HmAgentSwitchIpRoutePreferenceEntry  

hmAgentSwitchIpRoutePreferenceSource 1.3.6.1.4.1.248.15.2.2.7.1.1
Routing protocol for which this entry belongs
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER connected(1), static(2), ospf-intra(3), ospf-inter(4), ospf-ext-t1(5), ospf-ext-t2(6), rip(7)  

hmAgentSwitchIpRoutePreferenceValue 1.3.6.1.4.1.248.15.2.2.7.1.2
Adminstrative distance for this routing protocol.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..255  

hmAgentSwitchIpRouteStaticTable 1.3.6.1.4.1.248.15.2.2.8
......
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmAgentSwitchIpRouteStaticEntry

hmAgentSwitchIpRouteStaticEntry 1.3.6.1.4.1.248.15.2.2.8.1
The entry of the hmAgentSwitchIpRouteStaticTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  HmAgentSwitchIpRouteStaticEntry  

hmAgentSwitchIpRouteStaticDestination 1.3.6.1.4.1.248.15.2.2.8.1.1
.....
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

hmAgentSwitchIpRouteStaticDestinationMask 1.3.6.1.4.1.248.15.2.2.8.1.2
.....
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

hmAgentSwitchIpRouteStaticNextHop 1.3.6.1.4.1.248.15.2.2.8.1.3
.....
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

hmAgentSwitchIpRouteStaticPreference 1.3.6.1.4.1.248.15.2.2.8.1.4
.....
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..255  

hmAgentSwitchIpRouteStaticStatus 1.3.6.1.4.1.248.15.2.2.8.1.5
.....
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

hmAgentSwitchIpRouteStaticTrackId 1.3.6.1.4.1.248.15.2.2.8.1.6
The trackId of the object that should be tracked by this nexthop. If the object goes down, the nexthop is removed from the routing table, it is added again if the object goes up. A value of zero means no tracking
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

hmAgentSwitchIpVlanSingleMacMode 1.3.6.1.4.1.248.15.2.2.100
If enabled, all vlan routing interfaces use the same MAC address.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentSwitchIpTableSizesGroup 1.3.6.1.4.1.248.15.2.2.101
OBJECT IDENTIFIER    

hmAgentSwitchIpTableSizeArp 1.3.6.1.4.1.248.15.2.2.101.1
Sets the maximum size of the ARP table for routing
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 300..4096  

hmAgentSwitchIpTableSizeUCRoutes 1.3.6.1.4.1.248.15.2.2.101.2
Sets the size of the unicast route table
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 300..4096  

hmAgentSwitchIpTableSizeMCRoutes 1.3.6.1.4.1.248.15.2.2.101.3
Sets the size of the multicast route table
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..512  

hmAgentSwitchIpCurrentTableSizeArp 1.3.6.1.4.1.248.15.2.2.101.4
The current size of the ARP table for routing
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 300..4096  

hmAgentSwitchIpCurrentTableSizeUCRoutes 1.3.6.1.4.1.248.15.2.2.101.5
The current size of the unicast route table
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 300..4096  

hmAgentSwitchIpCurrentTableSizeMCRoutes 1.3.6.1.4.1.248.15.2.2.101.6
The current size of the multicast route table
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..512  

hmAgentRouterRipConfigGroup 1.3.6.1.4.1.248.15.2.3
OBJECT IDENTIFIER    

hmAgentRouterRipAdminState 1.3.6.1.4.1.248.15.2.3.1
Sets the administrative mode of RIP in the router.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentRouterRipSplitHorizonMode 1.3.6.1.4.1.248.15.2.3.2
Sets the RIP split horizon operating mode in the router. A value of none(1) means split horizon processing is disabled. When set to simple(2), the simple split horizon technique is used. When set to poisonReverse(3), the split horizon with poison reverse technique is used. The default split horizon mode is simple(2).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), simple(2), poisonReverse(3)  

hmAgentRouterRipAutoSummaryMode 1.3.6.1.4.1.248.15.2.3.3
Sets the RIP auto summarization mode in the router. A value of enable(1) means that routes advertized by this RIP router are combined, or summarized, whenever possible into aggregates. When set to disable(2), routes are not aggregated in RIP updates generated by this router. The default auto summary mode is enable(1).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentRouterRipHostRoutesAcceptMode 1.3.6.1.4.1.248.15.2.3.4
Sets the RIP host route acceptance mode in the router. A value of enable(1) means that host routes advertized to this RIP router will be accepted (learned) into its routing table. When set to disable(2), host routes advertized in RIP updates from neighboring routers are ignored. The default host routes accept mode is enable(1).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentRouterRipDefaultMetric 1.3.6.1.4.1.248.15.2.3.5
Default metric of redistributed routes, when RIP redistributes from other protocols.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..15  

hmAgentRouterRipDefaultMetricConfigured 1.3.6.1.4.1.248.15.2.3.6
Flag to determine whether RIP default-metric is configured or not.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

hmAgentRouterRipDefaultInfoOriginate 1.3.6.1.4.1.248.15.2.3.7
Flag to determine, whether RIP can advertise a default-route learned from another protocol.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

hmAgentRipRouteRedistTable 1.3.6.1.4.1.248.15.2.3.8
This table contains the MIB objects required to configure route-redistribution for RIP. Here, RIP is the Destination protocol and the source protocols can be any of : BGP, OSPF, Static, Connected.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmAgentRipRouteRedistEntry

hmAgentRipRouteRedistEntry 1.3.6.1.4.1.248.15.2.3.8.1
The entry of the hmAgentRipRouteRedistTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  HmAgentRipRouteRedistEntry  

hmAgentRipRouteRedistSource 1.3.6.1.4.1.248.15.2.3.8.1.1
Source route, from which RIP can redistribute routes. This object also acts as the identifier for the RIP redistribution Table entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER connected(1), static(2), ospf(3), bgp(4)  

hmAgentRipRouteRedistMode 1.3.6.1.4.1.248.15.2.3.8.1.2
User enabels/disables route-redistribution for a particular source protocol.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentRipRouteRedistMetric 1.3.6.1.4.1.248.15.2.3.8.1.3
Metric used for redistributing a particular source protocol route into RIP.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..15  

hmAgentRipRouteRedistMetricConfigured 1.3.6.1.4.1.248.15.2.3.8.1.4
Flag to determine whether RIP redistribute-metric is configured or not.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

hmAgentRipRouteRedistMatchInternal 1.3.6.1.4.1.248.15.2.3.8.1.5
If this flag is true, RIP redistributes OSPF internal routes. It will be non-applicable, when source protocol is other than ospf.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2), not-applicable(3)  

hmAgentRipRouteRedistMatchExternal1 1.3.6.1.4.1.248.15.2.3.8.1.6
If this flag is true, RIP redistributes OSPF External1 routes. It will be non-applicable, when source protocol is other than ospf.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2), not-applicable(3)  

hmAgentRipRouteRedistMatchExternal2 1.3.6.1.4.1.248.15.2.3.8.1.7
If this flag is true, RIP redistributes OSPF External2 routes. It will be non-applicable, when source protocol is other than ospf.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2), not-applicable(3)  

hmAgentRipRouteRedistMatchNSSAExternal1 1.3.6.1.4.1.248.15.2.3.8.1.8
If this flag is true, RIP redistributes OSPF NSSA-External1 routes. It will be non-applicable, when source protocol is other than ospf.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2), not-applicable(3)  

hmAgentRipRouteRedistMatchNSSAExternal2 1.3.6.1.4.1.248.15.2.3.8.1.9
If this flag is true, RIP redistributes OSPF NSSA-External2 routes. It will be non-applicable, when source protocol is other than ospf.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2), not-applicable(3)  

hmAgentRipRouteRedistDistList 1.3.6.1.4.1.248.15.2.3.8.1.10
Access-list number of the access-list, which filters routes received from a source-protocol.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..199  

hmAgentRipRouteRedistDistListConfigured 1.3.6.1.4.1.248.15.2.3.8.1.11
Flag to determine whether Access-list is configured or not.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

hmAgentRip2IfConfTable 1.3.6.1.4.1.248.15.2.3.9
A list of subnets which require separate configuration in RIP. Augments rip2IfConfTable in the RIPv2-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmAgentRip2IfConfEntry

hmAgentRip2IfConfEntry 1.3.6.1.4.1.248.15.2.3.9.1
A Single Routing Domain in a single Subnet. Augments rip2IfConfEntry in RIPv2-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  HmAgentRip2IfConfEntry  

hmAgentRip2IfConfAuthKeyId 1.3.6.1.4.1.248.15.2.3.9.1.1
The identifier for the authentication key used on this interface. This field is only meaningful when the RIPv2-MIB rip2IfConfAuthType is md5(3); otherwise, the value is not used.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..255  

hmAgentRip2InterfaceTable 1.3.6.1.4.1.248.15.2.3.10
The hmAgentRip2InterfaceTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmAgentRip2InterfaceEntry

hmAgentRip2InterfaceEntry 1.3.6.1.4.1.248.15.2.3.10.1
The entry of the hmAgentRip2InterfaceTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  HmAgentRip2InterfaceEntry  

hmAgentRip2InterfaceIfIndex 1.3.6.1.4.1.248.15.2.3.10.1.1
The IfIndex associated with this instance.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hmAgentRip2InterfaceAuthType 1.3.6.1.4.1.248.15.2.3.10.1.2
The type of Authentication used on this interface.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noAuthentication(1), simplePassword(2), md5(3)  

hmAgentRip2InterfaceAuthKey 1.3.6.1.4.1.248.15.2.3.10.1.3
The value to be used as the Authentication Key whenever the corresponding instance of hmAgentRip2InterfaceAuthType has a value other than noAuthentication. A modification of the corresponding instance of hmAgentRip2InterfaceAuthType does not modify the hmAgentRip2InterfaceAuthKey value. If a string shorter than 16 octets is supplied, it will be left- justified and padded to 16 octets, on the right, with nulls (0x00). Reading this object always results in an OCTET STRING of length zero; authentication may not be bypassed by reading the MIB object.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

hmAgentRip2InterfaceAuthKeyId 1.3.6.1.4.1.248.15.2.3.10.1.4
The identifier for the authentication key used on this interface. This field is only meaningful when the hmAgentRip2InterfaceAuthType is md5(3); otherwise, the value is not used.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..255  

hmAgentRip2InterfaceSendVersion 1.3.6.1.4.1.248.15.2.3.10.1.5
What the router sends on this interface. ripVersion1 implies sending RIP updates compliant with RFC 1058. rip1Compatible implies broadcasting RIP-2 updates using RFC 1058 route subsumption rules. ripVersion2 implies multicasting RIP-2 updates.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER doNotSend(1), ripVersion1(2), rip1Compatible(3), ripVersion2(4)  

hmAgentRip2InterfaceReceiveVersion 1.3.6.1.4.1.248.15.2.3.10.1.6
This indicates which version of RIP updates are to be accepted. Note that rip2 and rip1OrRip2 implies reception of multicast packets.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER rip1(1), rip2(2), rip1OrRip2(3), doNotReceive(4)  

hmAgentRip2InterfaceAdminState 1.3.6.1.4.1.248.15.2.3.10.1.7
Enables/disables RIP on the interface
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentRip2RcvBadPackets 1.3.6.1.4.1.248.15.2.3.10.1.8
......
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hmAgentRip2RcvBadRoutes 1.3.6.1.4.1.248.15.2.3.10.1.9
....
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hmAgentRip2SentUpdates 1.3.6.1.4.1.248.15.2.3.10.1.10
....
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hmAgentRouterRipUpdateTimerInterval 1.3.6.1.4.1.248.15.2.3.50
Sets the RIP update timer interval in the router. This is the time in seconds between two full routing table update packets.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..1000  

hmAgentRouterOspfConfigGroup 1.3.6.1.4.1.248.15.2.4
OBJECT IDENTIFIER    

hmAgentOspfDefaultMetric 1.3.6.1.4.1.248.15.2.4.1
Default metric of redistributed routes, when OSPF redistributes from other protocols.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..16777215  

hmAgentOspfDefaultMetricConfigured 1.3.6.1.4.1.248.15.2.4.2
Flag to determine whether OSPF default-metric is configured or not.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

hmAgentOspfDefaultInfoOriginate 1.3.6.1.4.1.248.15.2.4.3
Flag to determine, whether OSPF can advertise a default-route learned from another protocol.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

hmAgentOspfDefaultInfoOriginateAlways 1.3.6.1.4.1.248.15.2.4.4
When this flag is true, the router advertises 0.0.0.0/0.0.0.0 always. Without this option, OSPF will only advertise 0.0.0.0/0.0.0.0 if the router's forwarding table contains a default route.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

hmAgentOspfDefaultInfoOriginateMetric 1.3.6.1.4.1.248.15.2.4.5
Metric of the default route,which OSPF advertises when learned from other protocol.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..16777215  

hmAgentOspfDefaultInfoOriginateMetricConfigured 1.3.6.1.4.1.248.15.2.4.6
Flag to determine whether OSPF default-info originate metric is configured or not.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

hmAgentOspfDefaultInfoOriginateMetricType 1.3.6.1.4.1.248.15.2.4.7
Metric Type of the default route,which OSPF advertises when learned from other protocol. It can be 1(external type 1) or 2(external type 2).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER externalType1(1), externalType2(2)  

hmAgentOspfRouteRedistTable 1.3.6.1.4.1.248.15.2.4.8
This table contains the MIB objects required to configure route-redistribution for OSPF. Here, OSPF is the Destination protocol and the source protocols can be any of : BGP, RIP, Static, Connected.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmAgentOspfRouteRedistEntry

hmAgentOspfRouteRedistEntry 1.3.6.1.4.1.248.15.2.4.8.1
The entry of the hmAgentOspfRouteRedistTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  HmAgentOspfRouteRedistEntry  

hmAgentOspfRouteRedistSource 1.3.6.1.4.1.248.15.2.4.8.1.1
Source protocol, from which OSPF can redistribute routes. This object also acts as the identifier for the OSPF redistribution Table entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER connected(1), static(2), rip(3), bgp(4)  

hmAgentOspfRouteRedistMode 1.3.6.1.4.1.248.15.2.4.8.1.2
User enabels/disables route-redistribution for a particular source protocol.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentOspfRouteRedistMetric 1.3.6.1.4.1.248.15.2.4.8.1.3
Metric used for redistributing a particular source protocol route into OSPF.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..16777215  

hmAgentOspfRouteRedistMetricConfigured 1.3.6.1.4.1.248.15.2.4.8.1.4
Flag to determine whether OSPF redistribute-metric is configured or not.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

hmAgentOspfRouteRedistMetricType 1.3.6.1.4.1.248.15.2.4.8.1.5
Metric Type of routes,which OSPF redistributes from other source protocols. It can be 1(external type 1) or 2(external type 2).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER externalType1(1), externalType2(2)  

hmAgentOspfRouteRedistTag 1.3.6.1.4.1.248.15.2.4.8.1.6
It specifies the tag field in routes redistributed by OSPF.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..4294967295  

hmAgentOspfRouteRedistSubnets 1.3.6.1.4.1.248.15.2.4.8.1.7
If this value is false, then OSPF will not redistribute subnetted routes.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

hmAgentOspfRouteRedistDistList 1.3.6.1.4.1.248.15.2.4.8.1.8
Access-list number of the access-list, which filters routes received from a source-protocol.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..199  

hmAgentOspfRouteRedistDistListConfigured 1.3.6.1.4.1.248.15.2.4.8.1.9
Flag to determine whether Access-list is configured or not.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

hmAgentOspfIfTable 1.3.6.1.4.1.248.15.2.4.9
The OSPF Interface Table describes the inter- faces from the viewpoint of OSPF. Augments ospfIfTable from the OSPF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmAgentOspfIfEntry

hmAgentOspfIfEntry 1.3.6.1.4.1.248.15.2.4.9.1
The OSPF Interface Entry describes one inter- face from the viewpoint of OSPF. Augments ospfIfEntry in OSPF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  HmAgentOspfIfEntry  

hmAgentOspfIfAuthKeyId 1.3.6.1.4.1.248.15.2.4.9.1.1
The identifier for the authentication key used on this interface. This field is only meaningful when the OSPF-MIB ospfIfAuthType is md5(2); otherwise, the value is not used.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..255  

hmAgentOspfIfIpMtuIgnoreFlag 1.3.6.1.4.1.248.15.2.4.9.1.2
Configures the IP MTU Ignore Flag value for this OSPF interface.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentOspfVirtIfTable 1.3.6.1.4.1.248.15.2.4.10
Information about this router's virtual inter- faces. Augments ospfVirtIfTable from the OSPF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmAgentOspfVirtIfEntry

hmAgentOspfVirtIfEntry 1.3.6.1.4.1.248.15.2.4.10.1
Information about a single Virtual Interface. Augments ospfVirtIfEntry in OSPF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  HmAgentOspfVirtIfEntry  

hmAgentOspfVirtIfAuthKeyId 1.3.6.1.4.1.248.15.2.4.10.1.1
The identifier for the authentication key used on this virtual interface. This field is only meaningful when the OSPF-MIB ospfVirtIfAuthType is md5(2); otherwise, the value is not used.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..255  

hmAgentRouterOspfRFC1583CompatibilityMode 1.3.6.1.4.1.248.15.2.4.11
From RFC2328: Controls the preference rules used in Section 16.4 when choosing among multiple AS-external-LSAs advertising the same destination. When set to 'enabled', the preference rules remain those specified by RFC 1583 ([Ref9]). When set to 'disabled', the preference rules are those stated in Section 16.4.1, which prevent routing loops when AS- external-LSAs for the same destination have been originated from different areas. Set to 'enabled' by default. In order to minimize the chance of routing loops, all OSPF routers in an OSPF routing domain should have RFC1583Compatibility set identically. When there are routers present that have not been updated with the functionality specified in Section 16.4.1 of this memo, all routers should have RFC1583Compatibility set to 'enabled'. Otherwise, all routers should have RFC1583Compatibility set to 'disabled', preventing all routing loops.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentSnmpTrapFlagsConfigGroupLayer3 1.3.6.1.4.1.248.15.2.5
OBJECT IDENTIFIER    

hmAgentSnmpVRRPNewMasterTrapFlag 1.3.6.1.4.1.248.15.2.5.1
This flag enables the sending of VRRP new master notification traps.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentSnmpVRRPAuthFailureTrapFlag 1.3.6.1.4.1.248.15.2.5.2
This flag enables the sending of VRRP authentication failure notification traps.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentECMPGroup 1.3.6.1.4.1.248.15.2.7
OBJECT IDENTIFIER    

hmAgentECMPOspfMaxPaths 1.3.6.1.4.1.248.15.2.7.1
It sets the number of paths that OSPF can report for a given destination where maxpaths is platform-dependent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hmAgentRouterVrrpConfigGroup 1.3.6.1.4.1.248.15.2.8
OBJECT IDENTIFIER    

hmAgentRouterVrrpAdminState 1.3.6.1.4.1.248.15.2.8.1
Sets the administrative mode of VRRP in the router.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmVrrpExtGroup 1.3.6.1.4.1.248.15.2.9
OBJECT IDENTIFIER    

hmVrrpTrackingTable 1.3.6.1.4.1.248.15.2.9.1
This table contains variables to define an entry in the VRRP Tracking database.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmVrrpTrackingEntry

hmVrrpTrackingEntry 1.3.6.1.4.1.248.15.2.9.1.1
The entry of the hmVrrpTrackingTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  HmVrrpTrackingEntry  

hmVrrpTrackIfIndex 1.3.6.1.4.1.248.15.2.9.1.1.1
DURABLE: { 1:all } The interface number of the virtual router
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

hmVrrpTrackVrid 1.3.6.1.4.1.248.15.2.9.1.1.2
DURABLE: { 1:all } The virtual router id for this virtual router
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..255  

hmVrrpTrackId 1.3.6.1.4.1.248.15.2.9.1.1.3
DURABLE: { 1:all } The id of the object being tracked
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

hmVrrpTrackDecrement 1.3.6.1.4.1.248.15.2.9.1.1.4
DURABLE: { 1:all } The value by wich the current priority of the virtual router is decremented when the tracked object goes DOWN.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..253  

hmVrrpTrackOperStatus 1.3.6.1.4.1.248.15.2.9.1.1.5
Shows if the tracked object is currently UP od DOWN
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

hmVrrpTrackRowStatus 1.3.6.1.4.1.248.15.2.9.1.1.6
DURABLE: { 1:all } Defines the status of a vrrp tracking database entry. Set to createAndGo(4) to create a new row. Set to destroy(6) to delete an entry. Reads as active(1) if the tracked object exists and is trackable, notReady(3) otherwise.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hmVrrpExtTable 1.3.6.1.4.1.248.15.2.9.2
This table contains variables to define an entry in the VRRP enhancements database.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmVrrpExtEntry

hmVrrpExtEntry 1.3.6.1.4.1.248.15.2.9.2.1
The entry of the hmVrrpExtTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  HmVrrpExtEntry  

hmVrrpExtIfIndex 1.3.6.1.4.1.248.15.2.9.2.1.1
DURABLE: { 1:all } The interface number of the virtual router
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

hmVrrpExtVrid 1.3.6.1.4.1.248.15.2.9.2.1.2
DURABLE: { 1:all } The virtual router id for this virtual router
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..255  

hmVrrpExtDomainId 1.3.6.1.4.1.248.15.2.9.2.1.3
DURABLE: { 1:all } The domain this virtual router is a member of. If set to 0, the virtual router is not a member of any domain.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..8  

hmVrrpExtDomainRole 1.3.6.1.4.1.248.15.2.9.2.1.4
DURABLE: { 1:all } The role of this virtual router in its domain. This is none(1) if the virtual router is not member of a domain, supervisor(3) if it is the supervisor of its domain, member(2) otherwise.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), member(2), supervisor(3)  

hmVrrpExtDomainStatus 1.3.6.1.4.1.248.15.2.9.2.1.5
Shows if the domain configuration is correct for this virtual router
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noError(1), noSupervisor(2), supervisorDown(3)  

hmVrrpExtAdvertAddress 1.3.6.1.4.1.248.15.2.9.2.1.6
DURABLE: { 1:all } The IP address advertisements of the virtual router are sent to
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

hmVrrpExtAdvertTimer 1.3.6.1.4.1.248.15.2.9.2.1.7
DURABLE: { 1:all } This is used to set the interval between advertisements in milliseconds. This accesses the same value as vrrpOperAdvertisementInterval.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 100..255000  

hmVrrpExtOperPriority 1.3.6.1.4.1.248.15.2.9.2.1.8
DURABLE: { 1:all } The current operating priority of the virtual router. This can be different from the configured priority if tracked objects are down. For domain members this is the priority of the supervisor of that Domain.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..255  

hmVrrpExtNotifyAddress 1.3.6.1.4.1.248.15.2.9.2.1.9
DURABLE: { 1:all } The IP address notifications of the virtual router are sent to
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

hmVrrpExtNotifyLinkdown 1.3.6.1.4.1.248.15.2.9.2.1.10
DURABLE: { 1:all } Enables or disables sending of notification messages if the virtual router's interface goes down.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmVrrpExtPreemptionDelay 1.3.6.1.4.1.248.15.2.9.2.1.11
DURABLE: { 1:all } Time (in seconds) after startup of the virtual router by which the preemption of a Master with a lower priority is delayed.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

hmVrrpDomainTable 1.3.6.1.4.1.248.15.2.9.3
This table contains variables to define an entry in the VRRP domain database.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmVrrpDomainEntry

hmVrrpDomainEntry 1.3.6.1.4.1.248.15.2.9.3.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  HmVrrpDomainEntry  

hmVrrpDomainId 1.3.6.1.4.1.248.15.2.9.3.1.1
The domain ID.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..8  

hmVrrpDomainMemberSendAdv 1.3.6.1.4.1.248.15.2.9.3.1.2
DURABLE: { 1:all } Determines if the members of this domain send advertisement packets. If set to disabled(2), only the supervisor of the domain sends packets.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

hmVrrpDomainStatus 1.3.6.1.4.1.248.15.2.9.3.1.3
Shows if the configuration of the domain is complete.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noError(1), noSupervisor(2), supervisorDown(3)  

hmVrrpDomainSupervisorIfIndex 1.3.6.1.4.1.248.15.2.9.3.1.4
The interface number of the supervisor of the domain
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hmVrrpDomainSupervisorVrid 1.3.6.1.4.1.248.15.2.9.3.1.5
The virtual router id of the supervisor of the domain
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

hmVrrpDomainOperPriority 1.3.6.1.4.1.248.15.2.9.3.1.6
The current operating priority of the domain. This can be different from the configured priority if tracked objects are down. For domain members this is the priority of the supervisor of that Domain if the supervisor is configured and up.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

hmVrrpDomainSupervisorOperState 1.3.6.1.4.1.248.15.2.9.3.1.7
Shows the current operational state of the domain supervisor.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER initialize(1), backup(2), master(3), unknown(4)  

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor