HIRSCHMANN-MMP4-BASICL2-MIB

File: HIRSCHMANN-MMP4-BASICL2-MIB.mib (194139 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC Q-BRIDGE-MIB
IANAifType-MIB IF-MIB HMPRIV-MGMT-SNMP-MIB
INET-ADDRESS-MIB IEEE8021-PAE-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
IpAddress Integer32 Counter32
Gauge32 Unsigned32 TimeTicks
TEXTUAL-CONVENTION RowStatus MacAddress
DisplayString TruthValue VlanIndex
dot1qVlanIndex dot1qFdbId IANAifType
ifIndex hirschmann HmAgentLogSeverity
InetAddress dot1xPaePortNumber

Defined Types

HmAgentPortMask  
Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0' When setting this value, the system will ignore configuration for ports not between the first and last valid ports. Configuration of any port numbers between this range that are not valid ports return a failure message, but will still apply configuration for valid ports.
TEXTUAL-CONVENTION    
  OCTET STRING  

BridgeId  
the Bridge-Identifier as used in the Spanning Tree
TEXTUAL-CONVENTION    
  OCTET STRING Size(8)  

HmAgentDot1xPortControlMode  
The control values of the Authenticator PAE controlled Port.
TEXTUAL-CONVENTION    
  INTEGER forceUnauthorized(1), auto(2), forceAuthorized(3), macBased(4)  

HmAgentDot1xSessionTerminationAction  
The action to be taken on session termination .
TEXTUAL-CONVENTION    
  INTEGER default(1), reauthenticate(2)  

HmAgentTrapLogEntry  
SEQUENCE    
  hmAgentTrapLogIndex Integer32
  hmAgentTrapLogSystemTime DisplayString
  hmAgentTrapLogTrap DisplayString

HmAgentLoginSessionEntry  
SEQUENCE    
  hmAgentLoginSessionIndex Integer32
  hmAgentLoginSessionUserName DisplayString
  hmAgentLoginSessionIPAddress IpAddress
  hmAgentLoginSessionConnectionType INTEGER
  hmAgentLoginSessionIdleTime TimeTicks
  hmAgentLoginSessionSessionTime TimeTicks
  hmAgentLoginSessionStatus RowStatus

HmAgentLogSyslogHostEntry  
SEQUENCE    
  hmAgentLogHostTableIndex Unsigned32
  hmAgentLogHostTableIpAddress IpAddress
  hmAgentLogHostTablePort Unsigned32
  hmAgentLogHostTableSeverityFilter HmAgentLogSeverity
  hmAgentLogHostTableRowStatus RowStatus

HmAgentUserConfigEntry  
SEQUENCE    
  hmAgentUserIndex Integer32
  hmAgentUserName DisplayString
  hmAgentUserPassword DisplayString
  hmAgentUserAccessMode INTEGER
  hmAgentUserStatus RowStatus
  hmAgentUserAuthenticationType INTEGER
  hmAgentUserEncryptionType INTEGER
  hmAgentUserEncryptionPassword DisplayString

HmAgentLagSummaryConfigEntry  
SEQUENCE    
  hmAgentLagSummaryLagIndex Integer32
  hmAgentLagSummaryName DisplayString
  hmAgentLagSummaryFlushTimer Integer32
  hmAgentLagSummaryLinkTrap INTEGER
  hmAgentLagSummaryAdminMode INTEGER
  hmAgentLagSummaryStpMode INTEGER
  hmAgentLagSummaryAddPort Integer32
  hmAgentLagSummaryDeletePort Integer32
  hmAgentLagSummaryStatus RowStatus
  hmAgentLagSummaryType INTEGER

HmAgentLagDetailedConfigEntry  
SEQUENCE    
  hmAgentLagDetailedLagIndex Integer32
  hmAgentLagDetailedIfIndex Integer32
  hmAgentLagDetailedPortSpeed OBJECT IDENTIFIER
  hmAgentLagDetailedPortStatus INTEGER

HmAgentSwitchAddressAgingTimeoutEntry  
SEQUENCE    
  hmAgentSwitchAddressAgingTimeout Integer32

HmAgentSwitchStaticMacFilteringEntry  
SEQUENCE    
  hmAgentSwitchStaticMacFilteringVlanId Integer32
  hmAgentSwitchStaticMacFilteringAddress MacAddress
  hmAgentSwitchStaticMacFilteringSourcePortMask HmAgentPortMask
  hmAgentSwitchStaticMacFilteringDestPortMask HmAgentPortMask
  hmAgentSwitchStaticMacFilteringStatus RowStatus

HmAgentSwitchMFDBEntry  
SEQUENCE    
  hmAgentSwitchMFDBVlanId VlanIndex
  hmAgentSwitchMFDBMacAddress MacAddress
  hmAgentSwitchMFDBProtocolType INTEGER
  hmAgentSwitchMFDBType INTEGER
  hmAgentSwitchMFDBDescription DisplayString
  hmAgentSwitchMFDBForwardingPortMask HmAgentPortMask
  hmAgentSwitchMFDBFilteringPortMask HmAgentPortMask

HmAgentSwitchMFDBSummaryEntry  
SEQUENCE    
  hmAgentSwitchMFDBSummaryVlanId VlanIndex
  hmAgentSwitchMFDBSummaryMacAddress MacAddress
  hmAgentSwitchMFDBSummaryForwardingPortMask HmAgentPortMask

HmAgentPortMirrorEntry  
SEQUENCE    
  hmAgentPortMirrorSessionNum Unsigned32
  hmAgentPortMirrorDestinationPort Unsigned32
  hmAgentPortMirrorSourcePortMask HmAgentPortMask
  hmAgentPortMirrorIngressMask HmAgentPortMask
  hmAgentPortMirrorEgressMask HmAgentPortMask
  hmAgentPortMirrorAdminMode INTEGER

HmAgentDot3adAggPortEntry  
SEQUENCE    
  hmAgentDot3adAggPort Integer32
  hmAgentDot3adAggPortLACPMode INTEGER

HmAgentPortConfigEntry  
SEQUENCE    
  hmAgentPortDot1dBasePort Integer32
  hmAgentPortIfIndex Integer32
  hmAgentPortIanaType IANAifType
  hmAgentPortSTPMode INTEGER
  hmAgentPortSTPState INTEGER
  hmAgentPortAdminMode INTEGER
  hmAgentPortPhysicalMode INTEGER
  hmAgentPortPhysicalStatus INTEGER
  hmAgentPortLinkTrapMode INTEGER
  hmAgentPortClearStats INTEGER
  hmAgentPortDefaultType OBJECT IDENTIFIER
  hmAgentPortType OBJECT IDENTIFIER
  hmAgentPortAutoNegAdminStatus INTEGER
  hmAgentPortDot3FlowControlMode INTEGER
  hmAgentPortDVlanTagMode INTEGER
  hmAgentPortDVlanTagEthertype Integer32
  hmAgentPortDVlanTagCustomerId Integer32
  hmAgentPortMaxFrameSizeLimit Integer32
  hmAgentPortMaxFrameSize Integer32
  hmAgentPortVoiceVlanMode INTEGER
  hmAgentPortVoiceVlanID Integer32
  hmAgentPortVoiceVlanPriority INTEGER
  hmAgentPortVoiceVlanDataPriorityMode INTEGER
  hmAgentPortVoiceVlanOperationalStatus INTEGER
  hmAgentPortVoiceVlanDSCP Integer32
  hmAgentPortVoiceVlanAuthMode INTEGER

HmAgentProtocolGroupEntry  
SEQUENCE    
  hmAgentProtocolGroupId Integer32
  hmAgentProtocolGroupName DisplayString
  hmAgentProtocolGroupVlanId Integer32
  hmAgentProtocolGroupProtocolIP INTEGER
  hmAgentProtocolGroupProtocolARP INTEGER
  hmAgentProtocolGroupProtocolIPX INTEGER
  hmAgentProtocolGroupStatus RowStatus

HmAgentProtocolGroupPortEntry  
SEQUENCE    
  hmAgentProtocolGroupPortIfIndex Integer32
  hmAgentProtocolGroupPortStatus RowStatus

HmAgentStpPortEntry  
SEQUENCE    
  hmAgentStpPortState INTEGER
  hmAgentStpPortStatsMstpBpduRx Counter32
  hmAgentStpPortStatsMstpBpduTx Counter32
  hmAgentStpPortStatsRstpBpduRx Counter32
  hmAgentStpPortStatsRstpBpduTx Counter32
  hmAgentStpPortStatsStpBpduRx Counter32
  hmAgentStpPortStatsStpBpduTx Counter32
  hmAgentStpPortUpTime TimeTicks
  hmAgentStpPortMigrationCheck INTEGER
  hmAgentStpPortHelloTime Unsigned32

HmAgentStpCstPortEntry  
SEQUENCE    
  hmAgentStpCstPortOperEdge INTEGER
  hmAgentStpCstPortOperPointToPoint INTEGER
  hmAgentStpCstPortTopologyChangeAck INTEGER
  hmAgentStpCstPortEdge INTEGER
  hmAgentStpCstPortForwardingState INTEGER
  hmAgentStpCstPortId OCTET STRING
  hmAgentStpCstPortPathCost Unsigned32
  hmAgentStpCstPortPriority Unsigned32
  hmAgentStpCstDesignatedBridgeId OCTET STRING
  hmAgentStpCstDesignatedCost Unsigned32
  hmAgentStpCstDesignatedPortId OCTET STRING
  hmAgentStpCstExtPortPathCost Unsigned32
  hmAgentStpCstPortAutoEdge INTEGER
  hmAgentStpCstPortRole INTEGER
  hmAgentStpCstPortDisputed INTEGER
  hmAgentStpCstPortBpduGuardEffect INTEGER
  hmAgentStpCstPortBpduFilter INTEGER
  hmAgentStpCstPortBpduFlood INTEGER
  hmAgentStpCstPortRootGuard INTEGER
  hmAgentStpCstPortTCNGuard INTEGER
  hmAgentStpCstPortLoopGuard INTEGER

HmAgentStpMstEntry  
SEQUENCE    
  hmAgentStpMstId Unsigned32
  hmAgentStpMstBridgePriority Unsigned32
  hmAgentStpMstBridgeIdentifier OCTET STRING
  hmAgentStpMstDesignatedRootId OCTET STRING
  hmAgentStpMstRootPathCost Unsigned32
  hmAgentStpMstRootPortId OCTET STRING
  hmAgentStpMstTimeSinceTopologyChange TimeTicks
  hmAgentStpMstTopologyChangeCount Counter32
  hmAgentStpMstTopologyChangeParm INTEGER
  hmAgentStpMstRowStatus RowStatus

HmAgentStpMstPortEntry  
SEQUENCE    
  hmAgentStpMstPortForwardingState INTEGER
  hmAgentStpMstPortId OCTET STRING
  hmAgentStpMstPortPathCost Unsigned32
  hmAgentStpMstPortPriority Unsigned32
  hmAgentStpMstDesignatedBridgeId OCTET STRING
  hmAgentStpMstDesignatedCost Unsigned32
  hmAgentStpMstDesignatedPortId OCTET STRING
  hmAgentStpMstPortRole INTEGER
  hmAgentStpMstPortDisputed INTEGER
  hmAgentStpMstPortLoopInconsistentState INTEGER
  hmAgentStpMstPortTransitionsIntoLoopInconsistentState Counter32
  hmAgentStpMstPortTransitionsOutOfLoopInconsistentState Counter32
  hmAgentStpMstReceivedBridgeId OCTET STRING
  hmAgentStpMstReceivedRPC Unsigned32
  hmAgentStpMstReceivedPortId OCTET STRING

HmAgentStpMstVlanEntry  
SEQUENCE    
  hmAgentStpMstVlanRowStatus RowStatus

HmAgentClassOfServicePortEntry  
SEQUENCE    
  hmAgentClassOfServicePortPriority Integer32
  hmAgentClassOfServicePortClass Integer32

HmAgentRadiusAccountingConfigEntry  
SEQUENCE    
  hmAgentRadiusAccountingServerIndex Integer32
  hmAgentRadiusAccountingServerAddress IpAddress
  hmAgentRadiusAccountingPort Unsigned32
  hmAgentRadiusAccountingSecret DisplayString
  hmAgentRadiusAccountingStatus RowStatus

HmAgentRadiusServerConfigEntry  
SEQUENCE    
  hmAgentRadiusServerIndex Integer32
  hmAgentRadiusServerAddress IpAddress
  hmAgentRadiusServerPort Unsigned32
  hmAgentRadiusServerSecret DisplayString
  hmAgentRadiusServerPrimaryMode INTEGER
  hmAgentRadiusServerCurrentMode INTEGER
  hmAgentRadiusServerMsgAuth INTEGER
  hmAgentRadiusServerStatus RowStatus

HmAgentSwitchVoiceVlanDeviceEntry  
SEQUENCE    
  hmAgentSwitchVoiceVlanInterfaceNum Integer32
  hmAgentSwitchVoiceVlanDeviceMacAddress MacAddress

HmAgentDot1xPortConfigEntry  
SEQUENCE    
  hmAgentDot1xPortControlMode HmAgentDot1xPortControlMode
  hmAgentDot1xGuestVlanId Unsigned32
  hmAgentDot1xGuestVlanPeriod Unsigned32
  hmAgentDot1xUnauthenticatedVlan Unsigned32
  hmAgentDot1xMaxUsers Unsigned32
  hmAgentDot1xPortVlanAssigned Unsigned32
  hmAgentDot1xPortVlanAssignedReason INTEGER
  hmAgentDot1xPortSessionTimeout Unsigned32
  hmAgentDot1xPortTerminationAction HmAgentDot1xSessionTerminationAction
  hmAgentDot1xPortMABenabled INTEGER
  hmAgentDot1xPortMABenabledOperational INTEGER

HmAgentDot1xClientConfigEntry  
SEQUENCE    
  hmAgentDot1xClientMacAddress MacAddress
  hmAgentDot1xLogicalPort Unsigned32
  hmAgentDot1xInterface Unsigned32
  hmAgentDot1xClientAuthPAEstate INTEGER
  hmAgentDot1xClientBackendState INTEGER
  hmAgentDot1xClientUserName DisplayString
  hmAgentDot1xClientSessionTime Unsigned32
  hmAgentDot1xClientFilterID DisplayString
  hmAgentDot1xClientVlanAssigned Unsigned32
  hmAgentDot1xClientVlanAssignedReason INTEGER
  hmAgentDot1xClientSessionTimeout Unsigned32
  hmAgentDot1xClientTerminationAction HmAgentDot1xSessionTerminationAction

Defined Values

hmPlatform4BasicL2 1.3.6.1.4.1.248.15.1
The Hirschmann Private Platform4 Basic Layer 2 MIB definitions for Platform devices.
MODULE-IDENTITY    

hmPlatform4 1.3.6.1.4.1.248.15
OBJECT IDENTIFIER    

hmAgentInfoGroup 1.3.6.1.4.1.248.15.1.1
OBJECT IDENTIFIER    

hmAgentTrapLogGroup 1.3.6.1.4.1.248.15.1.1.2
OBJECT IDENTIFIER    

hmAgentTrapLogTotal 1.3.6.1.4.1.248.15.1.1.2.1
The total number of traps sent since last reset.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hmAgentTrapLogTotalSinceLastViewed 1.3.6.1.4.1.248.15.1.1.2.3
The number of traps sent since last viewed.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Integer32  

hmAgentTrapLogTable 1.3.6.1.4.1.248.15.1.1.2.4
Agent Trap Log
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmAgentTrapLogEntry

hmAgentTrapLogEntry 1.3.6.1.4.1.248.15.1.1.2.4.1
Agent trap log entry
Status: current Access: not-accessible
OBJECT-TYPE    
  HmAgentTrapLogEntry  

hmAgentTrapLogIndex 1.3.6.1.4.1.248.15.1.1.2.4.1.1
Unique index of trap entry
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hmAgentTrapLogSystemTime 1.3.6.1.4.1.248.15.1.1.2.4.1.2
System uptime when trap was sent. This entry shows how long the system has been up when the trap occurred.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

hmAgentTrapLogTrap 1.3.6.1.4.1.248.15.1.1.2.4.1.3
Description of the trap sent.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..512)  

hmAgentConfigGroup 1.3.6.1.4.1.248.15.1.2
OBJECT IDENTIFIER    

hmAgentCLIConfigGroup 1.3.6.1.4.1.248.15.1.2.1
OBJECT IDENTIFIER    

hmAgentLoginSessionTable 1.3.6.1.4.1.248.15.1.2.1.1
A table of the switch's login session
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmAgentLoginSessionEntry

hmAgentLoginSessionEntry 1.3.6.1.4.1.248.15.1.2.1.1.1
Login Session Entry
Status: current Access: not-accessible
OBJECT-TYPE    
  HmAgentLoginSessionEntry  

hmAgentLoginSessionIndex 1.3.6.1.4.1.248.15.1.2.1.1.1.1
Agent Login Session Index of the switch
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hmAgentLoginSessionUserName 1.3.6.1.4.1.248.15.1.2.1.1.1.2
Agent Login Session UserName of the switch
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

hmAgentLoginSessionIPAddress 1.3.6.1.4.1.248.15.1.2.1.1.1.3
Agent Login Session IP Address of the switch
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

hmAgentLoginSessionConnectionType 1.3.6.1.4.1.248.15.1.2.1.1.1.4
Agent Login Session Connection Type of the switch
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER serial(1), telnet(2)  

hmAgentLoginSessionIdleTime 1.3.6.1.4.1.248.15.1.2.1.1.1.5
Agent Login Session Idle Time of the switch
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

hmAgentLoginSessionSessionTime 1.3.6.1.4.1.248.15.1.2.1.1.1.6
Agent Login Session Time of the switch
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

hmAgentLoginSessionStatus 1.3.6.1.4.1.248.15.1.2.1.1.1.7
Status of the user. active(1) - This connection is active. destroy(6) - Set to this value to disconnect this user.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

hmAgentLogging 1.3.6.1.4.1.248.15.14
OBJECT IDENTIFIER    

hmAgentLogConfigGroup 1.3.6.1.4.1.248.15.14.1
OBJECT IDENTIFIER    

hmAgentLogSysLogConfigGroup 1.3.6.1.4.1.248.15.14.1.4
OBJECT IDENTIFIER    

hmAgentLogSyslogAdminStatus 1.3.6.1.4.1.248.15.14.1.4.1
For Enabling and Disabling logging to configured syslog hosts. Setting this to disable stops logging to all syslog hosts.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentLogSyslogHostTable 1.3.6.1.4.1.248.15.14.1.4.5
Syslog host table containing syslog host entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmAgentLogSyslogHostEntry

hmAgentLogSyslogHostEntry 1.3.6.1.4.1.248.15.14.1.4.5.1
Syslog Host entry attributes.
Status: current Access: not-accessible
OBJECT-TYPE    
  HmAgentLogSyslogHostEntry  

hmAgentLogHostTableIndex 1.3.6.1.4.1.248.15.14.1.4.5.1.1
Index to syslog host entry in syslog host table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

hmAgentLogHostTableIpAddress 1.3.6.1.4.1.248.15.14.1.4.5.1.3
Syslog Host table IP Address.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

hmAgentLogHostTablePort 1.3.6.1.4.1.248.15.14.1.4.5.1.4
Syslog Host table port number.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 1..65535  

hmAgentLogHostTableSeverityFilter 1.3.6.1.4.1.248.15.14.1.4.5.1.5
Configures the minimum severity that will be stored in the In Memory log.
Status: current Access: read-create
OBJECT-TYPE    
  HmAgentLogSeverity  

hmAgentLogHostTableRowStatus 1.3.6.1.4.1.248.15.14.1.4.5.1.7
Syslog Host table row status
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hmAgentTelnetConfigGroup 1.3.6.1.4.1.248.15.1.2.1.2
OBJECT IDENTIFIER    

hmAgentTelnetLoginTimeout 1.3.6.1.4.1.248.15.1.2.1.2.1
Telnet login timeout (minutes) Config telnet timeout will set the telnet session timeout value. A session is active as long as the session has not remained idle for the value set. Specify a value from 1 to 160. Note: Changing the timeout value for active sessions does not become effective until the session is reaccessed. Any keystroke will also activate the new timeout duration.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..160  

hmAgentTelnetMaxSessions 1.3.6.1.4.1.248.15.1.2.1.2.2
Maximum number of Telnet Sessions Config telnet maxsessions is an integer value from 0 to 5 that specifies the maximum number of telnet sessions that can be established. If the value is 0, no Telnet session can be established.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..5  

hmAgentTelnetAllowNewMode 1.3.6.1.4.1.248.15.1.2.1.2.3
Allow new telnet sessions (enable or disable) Config telnet disable means that no new Telnet sessions are to be established. Any already established session remains active until the session is ended or an abnormal network error ends it.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentUserConfigGroup 1.3.6.1.4.1.248.15.1.2.1.3
OBJECT IDENTIFIER    

hmAgentUserConfigCreate 1.3.6.1.4.1.248.15.1.2.1.3.1
Create a new user. When set with a non-empty string, a new user with that name will be created. This object will only return an empty string. This string is limited to alpha-numeric strings (uncluding the '-' and '_' characters).
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..32)  

hmAgentUserConfigTable 1.3.6.1.4.1.248.15.1.2.1.3.2
User Config Table
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmAgentUserConfigEntry

hmAgentUserConfigEntry 1.3.6.1.4.1.248.15.1.2.1.3.2.1
User Config Entry
Status: current Access: not-accessible
OBJECT-TYPE    
  HmAgentUserConfigEntry  

hmAgentUserIndex 1.3.6.1.4.1.248.15.1.2.1.3.2.1.1
Agent User Config Index
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

hmAgentUserName 1.3.6.1.4.1.248.15.1.2.1.3.2.1.2
Agent User Name. This string is limited to alpha-numeric strings (including the '-' and '_' characters).
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..32)  

hmAgentUserPassword 1.3.6.1.4.1.248.15.1.2.1.3.2.1.3
Agent User Password This object will return an empty string even if a password is set.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

hmAgentUserAccessMode 1.3.6.1.4.1.248.15.1.2.1.3.2.1.4
Agent User Access Mode
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER read(1), write(2)  

hmAgentUserStatus 1.3.6.1.4.1.248.15.1.2.1.3.2.1.5
Agent User Status. active(1) - This user account is active. destroy(6) - Set to this value to remove this user account.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

hmAgentUserAuthenticationType 1.3.6.1.4.1.248.15.1.2.1.3.2.1.6
SNMPv3 User Authentication. The user passsword must be set to a string greater than or equal to 8 characters for this to be set to anything but none(1). none(1) - no authentication used hmacmd5(1) - Use HMAC-MD5 authentication hmacsha(1) - Use HMAC-SHA authentication
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), hmacmd5(2), hmacsha(3)  

hmAgentUserEncryptionType 1.3.6.1.4.1.248.15.1.2.1.3.2.1.7
SNMPv3 User Encryption Can not be set to des(2) if hmAgentUserAuthenticationType is set to none(1). none(1) - no encryption used des(2) - DES encryption used
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), des(2)  

hmAgentUserEncryptionPassword 1.3.6.1.4.1.248.15.1.2.1.3.2.1.8
SNMPv3 User Encryption Password This object will return an empty string even if a password is set. hmAgentUserEncryptionType must be set to des(2) before this object can be configured. This object will return an empty string even if a password is set.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(8..64)  

hmAgentUserDefaultPwdActive 1.3.6.1.4.1.248.15.1.2.1.3.248
Shows if one or more default passwords are active for users configured in the hmAgentUserConfigTable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

hmAgentLagConfigGroup 1.3.6.1.4.1.248.15.1.2.2
OBJECT IDENTIFIER    

hmAgentLagConfigCreate 1.3.6.1.4.1.248.15.1.2.2.1
Agent LAG Create. When this object is set with a non-empty string, a new LAG will be created if possible with the entered string as its name.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0|1..15)  

hmAgentLagSummaryConfigTable 1.3.6.1.4.1.248.15.1.2.2.2
A summary table of the switch's LAG config entries
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmAgentLagSummaryConfigEntry

hmAgentLagSummaryConfigEntry 1.3.6.1.4.1.248.15.1.2.2.2.1
Switch's LAG config entry
Status: current Access: not-accessible
OBJECT-TYPE    
  HmAgentLagSummaryConfigEntry  

hmAgentLagSummaryLagIndex 1.3.6.1.4.1.248.15.1.2.2.2.1.1
Agent LAG IfIndex. This value corresponds with the LAG interface in the ifTable.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hmAgentLagSummaryName 1.3.6.1.4.1.248.15.1.2.2.2.1.2
Agent LAG Name. The associated name of the LAG used during creation.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..15)  

hmAgentLagSummaryFlushTimer 1.3.6.1.4.1.248.15.1.2.2.2.1.3
Agent LAG FlushTimer.
Status: obsolete Access: read-write
OBJECT-TYPE    
  Integer32  

hmAgentLagSummaryLinkTrap 1.3.6.1.4.1.248.15.1.2.2.2.1.4
Agent LAG LinkTrap. Configures sending Link Up/Down traps when the LAG interface goes Up or Down.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentLagSummaryAdminMode 1.3.6.1.4.1.248.15.1.2.2.2.1.5
Agent LAG AdminMode. Administratively enables or disables this LAG interface.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentLagSummaryStpMode 1.3.6.1.4.1.248.15.1.2.2.2.1.6
Agent LAG StpMode.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER off(3), on(4)  

hmAgentLagSummaryAddPort 1.3.6.1.4.1.248.15.1.2.2.2.1.7
Agent LAG AddPort. Set to a non 0 value to add a port to the LAG. Values correspond to ifIndex values in the ifTable. Note: hmAgentPortType for the port to be added must be full duplex and the same speed as previously added port(s), if any.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hmAgentLagSummaryDeletePort 1.3.6.1.4.1.248.15.1.2.2.2.1.8
Agent LAG DeletePort. Set to a non 0 value to remove a port from the LAG. Values correspond to ifIndex values in the ifTable.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hmAgentLagSummaryStatus 1.3.6.1.4.1.248.15.1.2.2.2.1.9
Agent LAG Status. active(1) - This LAG is enabled. destroy(6) - Set to this value to remove the LAG.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

hmAgentLagSummaryType 1.3.6.1.4.1.248.15.1.2.2.2.1.10
Agent LAG Type. static(1) - This LAG is staticly maintained. dynamic(2) - This LAG is dynamicly maintained.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER static(1), dynamic(2)  

hmAgentLagDetailedConfigTable 1.3.6.1.4.1.248.15.1.2.2.3
A detailed table of the switch's LAG config entries
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmAgentLagDetailedConfigEntry

hmAgentLagDetailedConfigEntry 1.3.6.1.4.1.248.15.1.2.2.3.1
Switch's LAG config entry
Status: current Access: not-accessible
OBJECT-TYPE    
  HmAgentLagDetailedConfigEntry  

hmAgentLagDetailedLagIndex 1.3.6.1.4.1.248.15.1.2.2.3.1.1
LAG index
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hmAgentLagDetailedIfIndex 1.3.6.1.4.1.248.15.1.2.2.3.1.2
LAG port index
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hmAgentLagDetailedPortSpeed 1.3.6.1.4.1.248.15.1.2.2.3.1.3
LAG port speed. See hmAgentPortType for a description and list of valid values.
Status: current Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER  

hmAgentLagDetailedPortStatus 1.3.6.1.4.1.248.15.1.2.2.3.1.4
LAG port status. active(1) - Actively participating in the LAG. inactive(2) - Not participating in the LAG.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER active(1), inactive(2)  

hmAgentLagConfigStaticCapability 1.3.6.1.4.1.248.15.1.2.2.4
Agent LAG Static Capability. Configures whether Static LAGs are supported on this device.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentSpanningTreeConfigGroup 1.3.6.1.4.1.248.15.1.2.7
OBJECT IDENTIFIER    

hmAgentSpanningTreeMode 1.3.6.1.4.1.248.15.1.2.7.1
The switch's Spanning Tree Switch Status
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentSwitchConfigGroup 1.3.6.1.4.1.248.15.1.2.8
OBJECT IDENTIFIER    

hmAgentSwitchAddressAgingTimeoutTable 1.3.6.1.4.1.248.15.1.2.8.4
The switch's address aging timeout table
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmAgentSwitchAddressAgingTimeoutEntry

hmAgentSwitchAddressAgingTimeoutEntry 1.3.6.1.4.1.248.15.1.2.8.4.1
Aging information about a specific Filtering Database.
Status: current Access: not-accessible
OBJECT-TYPE    
  HmAgentSwitchAddressAgingTimeoutEntry  

hmAgentSwitchAddressAgingTimeout 1.3.6.1.4.1.248.15.1.2.8.4.1.1
The FDB entry's address aging timeout (in seconds)
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 10..1000000  

hmAgentSwitchBroadcastControlMode 1.3.6.1.4.1.248.15.1.2.8.2
The switch config broadcast allows you to enable or disable broadcast storm recovery mode. When you specify Enable for Broadcast Storm Recovery and the broadcast traffic on any Ethernet port exceeds 20 percent of the link speed, the switch blocks (discards) the broadcast traffic until the broadcast traffic returns to 10 percent or less. Upper limit for 10M link is 20% and lower limit is 10%. For 100M link Upper limit is 5% and lower limit is 2%
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentSwitchDot3FlowControlMode 1.3.6.1.4.1.248.15.1.2.8.3
Config switchconfig flowcontrol allows you to enable or disable 802.3x flow control for the switch. This value applies to only full-duplex mode ports.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentSwitchStaticMacFilteringTable 1.3.6.1.4.1.248.15.1.2.8.5
The switch's static Mac filtering table
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmAgentSwitchStaticMacFilteringEntry

hmAgentSwitchStaticMacFilteringEntry 1.3.6.1.4.1.248.15.1.2.8.5.1
Per-port ingress/egress filter configuration based on VLAN Id and MAC address.
Status: current Access: not-accessible
OBJECT-TYPE    
  HmAgentSwitchStaticMacFilteringEntry  

hmAgentSwitchStaticMacFilteringVlanId 1.3.6.1.4.1.248.15.1.2.8.5.1.1
The Static MAC Filter Vlan Id
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hmAgentSwitchStaticMacFilteringAddress 1.3.6.1.4.1.248.15.1.2.8.5.1.2
The Static MAC Filter MAC address
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

hmAgentSwitchStaticMacFilteringSourcePortMask 1.3.6.1.4.1.248.15.1.2.8.5.1.3
The Static MAC Filter source port mask. When setting this value, the system will ignore configuration for ports not between the first and last valid ports. Configuration of any port numbers between this range that are not valid ports return a failure message, but will still apply configuration for valid ports. To obtain port numbers from interface numbers, use the objects hmAgentPortDot1dBasePort and hmAgentPortIfIndex in the hmAgentPortConfigTable table.
Status: current Access: read-write
OBJECT-TYPE    
  HmAgentPortMask  

hmAgentSwitchStaticMacFilteringDestPortMask 1.3.6.1.4.1.248.15.1.2.8.5.1.4
The Static MAC Filter destination port mask. When setting this value, the system will ignore configuration for ports not between the first and last valid ports. Configuration of any port numbers between this range that are not valid ports return a failure message, but will still apply configuration for valid ports. To obtain port numbers from interface numbers, use the objects hmAgentPortDot1dBasePort and hmAgentPortIfIndex in the hmAgentPortConfigTable table.
Status: current Access: read-write
OBJECT-TYPE    
  HmAgentPortMask  

hmAgentSwitchStaticMacFilteringStatus 1.3.6.1.4.1.248.15.1.2.8.5.1.5
The Static MAC Filter status. Supported values: active(1) - valid entry createAndGo(4) - used to create a new entry destroy(6) - removes the entry
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hmAgentSwitchIGMPSnoopingGroup 1.3.6.1.4.1.248.15.1.2.8.6
OBJECT IDENTIFIER    

hmAgentSwitchIGMPSnoopingAdminMode 1.3.6.1.4.1.248.15.1.2.8.6.1
This enables or disables IGMP Snooping on the system.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentSwitchIGMPSnoopingGroupMembershipInterval 1.3.6.1.4.1.248.15.1.2.8.6.2
The amount of time in seconds a switch will wait for a report for a particular group on a particular interface before it deletes the interface from the entry.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 3..3600  

hmAgentSwitchIGMPSnoopingMaxResponseTime 1.3.6.1.4.1.248.15.1.2.8.6.3
The amount of time in seconds a switch will wait after sending a query on an interface because it did not receive a report for a particular group in that interface. This value must be less than hmAgentSwitchIGMPSnoopingQueryInterval.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..3598  

hmAgentSwitchIGMPSnoopingMRPExpirationTime 1.3.6.1.4.1.248.15.1.2.8.6.4
Multicast Router Present Expiration Time. The amount of time in seconds a switch will wait for a query to be received on an interface before the interface is removed from the list of interfaces with mutlticast routers attached. A value of zero indicates an infinite timeout, i.e. the entries in the list will not expire.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..3600  

hmAgentSwitchIGMPSnoopingPortMask 1.3.6.1.4.1.248.15.1.2.8.6.5
IGMP Snooping Port Mask. This allows configuration of IGMP Snooping on selected ports. IGMP Snooping cannot be enabled on an interface that has routing enabled, or is a member of a LAG. If a port which has IGMP Snooping enabled becomes enabled for routing, or is enlisted as a member of a LAG, IGMP Snooping functionality will be disabled on that port. IGMP Snooping functionality will be subsequently be reenabled if routing is disabled or LAG membership is removed from an interface that had previously had IGMP Snooping enabled. To obtain port numbers from interface numbers, use the objects hmAgentPortDot1dBasePort and hmAgentPortIfIndex in the hmAgentPortConfigTable table.
Status: current Access: read-write
OBJECT-TYPE    
  HmAgentPortMask  

hmAgentSwitchIGMPSnoopingMulticastControlFramesProcessed 1.3.6.1.4.1.248.15.1.2.8.6.6
Multicast Control Frames Processed by CPU. The number of multicast control frames that have been processed by the CPU.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hmAgentSwitchMFDBGroup 1.3.6.1.4.1.248.15.1.2.8.7
OBJECT IDENTIFIER    

hmAgentSwitchMFDBTable 1.3.6.1.4.1.248.15.1.2.8.7.1
The Multicast Forwarding Database table
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmAgentSwitchMFDBEntry

hmAgentSwitchMFDBEntry 1.3.6.1.4.1.248.15.1.2.8.7.1.1
Contains Forwarding and Filtering information per Vlan Index, MAC Address, and Component User.
Status: current Access: not-accessible
OBJECT-TYPE    
  HmAgentSwitchMFDBEntry  

hmAgentSwitchMFDBVlanId 1.3.6.1.4.1.248.15.1.2.8.7.1.1.1
Vlan Index for which this entry is associated with.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

hmAgentSwitchMFDBMacAddress 1.3.6.1.4.1.248.15.1.2.8.7.1.1.2
A multicast MAC address for which the switch has forwarding and or filtering information.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

hmAgentSwitchMFDBProtocolType 1.3.6.1.4.1.248.15.1.2.8.7.1.1.3
The component that is responsible for this entry in the Multicast Forwarding Database.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER static(1), gmrp(2), igmp(3), msd(4)  

hmAgentSwitchMFDBType 1.3.6.1.4.1.248.15.1.2.8.7.1.1.4
This displays the type of the entry. static(1) - Entries configured by the end user dynamic(2) - Entries added as a result of a learning process or protocol
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER static(1), dynamic(2)  

hmAgentSwitchMFDBDescription 1.3.6.1.4.1.248.15.1.2.8.7.1.1.5
Text description of this multicast table entry.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

hmAgentSwitchMFDBForwardingPortMask 1.3.6.1.4.1.248.15.1.2.8.7.1.1.6
BitMask indicating which ports this entry indicates should be forwarded. To obtain port numbers from interface numbers, use the objects hmAgentPortDot1dBasePort and hmAgentPortIfIndex in the hmAgentPortConfigTable table.
Status: current Access: read-only
OBJECT-TYPE    
  HmAgentPortMask  

hmAgentSwitchMFDBFilteringPortMask 1.3.6.1.4.1.248.15.1.2.8.7.1.1.7
BitMask indicating which ports this entry indicates should be filtered. To obtain port numbers from interface numbers, use the objects hmAgentPortDot1dBasePort and hmAgentPortIfIndex in the hmAgentPortConfigTable table.
Status: current Access: read-only
OBJECT-TYPE    
  HmAgentPortMask  

hmAgentSwitchMFDBSummaryTable 1.3.6.1.4.1.248.15.1.2.8.7.2
The Multicast Forwarding Database Summary table
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmAgentSwitchMFDBSummaryEntry

hmAgentSwitchMFDBSummaryEntry 1.3.6.1.4.1.248.15.1.2.8.7.2.1
Summarizes the forwarding ports for all components registered for all MFDB table entries with the same Vlan Index and MAC Address.
Status: current Access: not-accessible
OBJECT-TYPE    
  HmAgentSwitchMFDBSummaryEntry  

hmAgentSwitchMFDBSummaryVlanId 1.3.6.1.4.1.248.15.1.2.8.7.2.1.1
Vlan Index for which this entry is associated with.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

hmAgentSwitchMFDBSummaryMacAddress 1.3.6.1.4.1.248.15.1.2.8.7.2.1.2
A multicast MAC address for which the switch has forwarding and or filtering information.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

hmAgentSwitchMFDBSummaryForwardingPortMask 1.3.6.1.4.1.248.15.1.2.8.7.2.1.3
Port Mask indicating which ports this entry indicates should be forwarded. To obtain port numbers from interface numbers, use the objects hmAgentPortDot1dBasePort and hmAgentPortIfIndex in the hmAgentPortConfigTable table.
Status: current Access: read-only
OBJECT-TYPE    
  HmAgentPortMask  

hmAgentSwitchMFDBMaxTableEntries 1.3.6.1.4.1.248.15.1.2.8.7.3
This displays the maximum number of entries that can possibly be in the Multicast Forwarding Database table.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hmAgentSwitchMFDBMostEntriesUsed 1.3.6.1.4.1.248.15.1.2.8.7.4
This displays the largest number of entries that have been present in the Multicast Forwarding Database table. This value is also known as the MFDB high-water mark.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hmAgentSwitchMFDBCurrentEntries 1.3.6.1.4.1.248.15.1.2.8.7.5
This displays the current number of entries in the Multicast Forwarding Database table.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hmAgentSwitchDVlanTagGroup 1.3.6.1.4.1.248.15.1.2.8.8
OBJECT IDENTIFIER    

hmAgentSwitchDVlanTagEthertype 1.3.6.1.4.1.248.15.1.2.8.8.1
Configures the Double Vlan Tag Ethertype for the switch. If this object is supported, ethertype cannot be configured per port. Commonly used are the Ethertypes for vman tags (34984, or 0x88A8) and dot1q tags (33024, or 0x8100).
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

hmAgentTransferConfigGroup 1.3.6.1.4.1.248.15.1.2.9
OBJECT IDENTIFIER    

hmAgentTransferUploadGroup 1.3.6.1.4.1.248.15.1.2.9.1
OBJECT IDENTIFIER    

hmAgentTransferUploadMode 1.3.6.1.4.1.248.15.1.2.9.1.1
Transfer upload mode configures the mode to use when uploading from the switch. The mode is either X/Y/ZMODEM or TFTP. X/Y/ZMODEM is valid only when the file transfer is initiated by the serial EIA 232 port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER tftp(1), xmodem(2), ymodem(3), zmodem(4)  

hmAgentTransferUploadServerIP 1.3.6.1.4.1.248.15.1.2.9.1.2
Transfer upload tftpserverip configures the IP address of the server where the file is located. It is valid only when the Transfer Mode is TFTP. The address is 4 integer bytes ranging from 0 to 255.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

hmAgentTransferUploadPath 1.3.6.1.4.1.248.15.1.2.9.1.3
Transfer upload tftppath configures the directory path where the file is to be uploaded to. The switch remembers the last file path used.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

hmAgentTransferUploadFilename 1.3.6.1.4.1.248.15.1.2.9.1.4
Transfer upload tftpfilename configures the file name for the file being uploaded from the switch. It can be up to 32 alphanumeric characters. The switch remembers the last file name used. File path can be appended to the file name if the string is less than 17 characters. Otherwise, the File Path field will need to be used and the File Name will be appended to the File Path as is. An example would be File Path set to c:/tftp/code/ and File Name set to e1r1v1.opr. Note: File Name, File Path, and TFTP Server IP Address are applicable only if the Transfer Mode is TFTP.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

hmAgentTransferUploadDataType 1.3.6.1.4.1.248.15.1.2.9.1.5
Transfer upload datatype configures the type of file to upload from the switch. The types for upload are: - Configuration File - Error log - Message log - Trap log
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER config(2), errorlog(3), messagelog(4), traplog(5), clibanner(6)  

hmAgentTransferUploadStart 1.3.6.1.4.1.248.15.1.2.9.1.6
Transfer upload start will start an upload transfer. The hmAgentTransferUploadMode object must not be set to xmodem(2), ymodem(3), or zmodem(4) to initiate a transfer via SNMP.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentTransferUploadStatus 1.3.6.1.4.1.248.15.1.2.9.1.7
Indicates the current status of an upload transfer.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notInitiated(1), transferStarting(2), errorStarting(3), wrongFileType(4), updatingConfig(5), invalidConfigFile(6), writingToFlash(7), failureWritingToFlash(8), checkingCRC(9), failedCRC(10), unknownDirection(11), transferSuccessful(12), transferFailed(13)  

hmAgentTransferDownloadGroup 1.3.6.1.4.1.248.15.1.2.9.2
OBJECT IDENTIFIER    

hmAgentTransferDownloadMode 1.3.6.1.4.1.248.15.1.2.9.2.1
Transfer download mode configures the mode to use when downloading to the switch. The mode is either X/Y/ZMODEM or TFTP. X/Y/ZMODEM is valid only when the file transfer is initiated by the serial EIA 232 port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER tftp(1), xmodem(2), ymodem(3), zmodem(4)  

hmAgentTransferDownloadServerIP 1.3.6.1.4.1.248.15.1.2.9.2.2
Transfer download tftpserverip configures the IP address of the server where the file is located. It is valid only when the Transfer Mode is TFTP. The address is 4 integer bytes ranging from 0 to 255.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

hmAgentTransferDownloadPath 1.3.6.1.4.1.248.15.1.2.9.2.3
Transfer download tftppath configures the directory path where the file is located. The switch remembers the last file path used.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

hmAgentTransferDownloadFilename 1.3.6.1.4.1.248.15.1.2.9.2.4
Transfer download tftpfilename configures the file name for the file being downloaded to the switch. It can be up to 32 alphanumeric characters. The switch remembers the last file name used. File path can be appended to the file name if the string is less than 33 characters. Otherwise, the File Path field will need to be used and the File Name will be appended to the File Path as is. An example would be File Path set to c:/tftp/code/ and File Name set to e1r1v1.opr. Note: File Name, File Path, and TFTP Server IP Address are applicable only if the Transfer Mode is TFTP.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

hmAgentTransferDownloadDataType 1.3.6.1.4.1.248.15.1.2.9.2.5
Transfer download datatype configures the type of file to download to the switch. The types for download are: code - Code File config - Configuration File
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER code(2), config(3), sshkey-rsa1(4), sshkey-rsa2(5), sshkey-dsa(6), sslpem-root(7), sslpem-server(8), sslpem-dhweak(9), sslpem-dhstrong(10), clibanner(11)  

hmAgentTransferDownloadStart 1.3.6.1.4.1.248.15.1.2.9.2.6
Transfer download start will start an download transfer. The hmAgentTransferDownloadMode object must not be set to xmodem(2), ymodem(3), or zmodem(4) to initiate a transfer via SNMP.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentTransferDownloadStatus 1.3.6.1.4.1.248.15.1.2.9.2.7
Indicates the current status of an download transfer.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notInitiated(1), transferStarting(2), errorStarting(3), wrongFileType(4), updatingConfig(5), invalidConfigFile(6), writingToFlash(7), failureWritingToFlash(8), checkingCRC(9), failedCRC(10), unknownDirection(11), transferSuccessful(12), transferFailed(13)  

hmAgentPortMirroringGroup 1.3.6.1.4.1.248.15.1.2.10
OBJECT IDENTIFIER    

hmAgentMirroredPortIfIndex 1.3.6.1.4.1.248.15.1.2.10.1
IfIndex of the mirrored port
Status: obsolete Access: read-write
OBJECT-TYPE    
  Integer32  

hmAgentProbePortIfIndex 1.3.6.1.4.1.248.15.1.2.10.2
IfIndex of the probe port
Status: obsolete Access: read-write
OBJECT-TYPE    
  Integer32  

hmAgentPortMirroringMode 1.3.6.1.4.1.248.15.1.2.10.3
Port mirroring mode: enable - enable mirroring mode disable - disable mirroring mode delete - clear MirroredPort and Probe Port configuration
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2), delete(3)  

hmAgentPortMirrorTable 1.3.6.1.4.1.248.15.1.2.10.4
This table includes entries for each Port Mirroring session.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmAgentPortMirrorEntry

hmAgentPortMirrorEntry 1.3.6.1.4.1.248.15.1.2.10.4.1
Provides configuration of a Port Mirroring session specifying the destination port, and the source Port Mask, providing a many-to-one mapping.
Status: current Access: not-accessible
OBJECT-TYPE    
  HmAgentPortMirrorEntry  

hmAgentPortMirrorSessionNum 1.3.6.1.4.1.248.15.1.2.10.4.1.1
The Session number of this mirroring entry. The number of sessions is fixed, and is platform dependant.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

hmAgentPortMirrorDestinationPort 1.3.6.1.4.1.248.15.1.2.10.4.1.2
The port which traffic from the mirrored ports will be sent to.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

hmAgentPortMirrorSourcePortMask 1.3.6.1.4.1.248.15.1.2.10.4.1.3
The ports from which traffic will be sent to the destination port. The destination port can not be included in this list of ports.
Status: current Access: read-write
OBJECT-TYPE    
  HmAgentPortMask  

hmAgentPortMirrorIngressMask 1.3.6.1.4.1.248.15.1.2.10.4.1.248
The ports from which ingress traffic will be mirrored.
Status: current Access: read-write
OBJECT-TYPE    
  HmAgentPortMask  

hmAgentPortMirrorEgressMask 1.3.6.1.4.1.248.15.1.2.10.4.1.249
The ports from which egress traffic will be mirrored.
Status: current Access: read-write
OBJECT-TYPE    
  HmAgentPortMask  

hmAgentPortMirrorAdminMode 1.3.6.1.4.1.248.15.1.2.10.4.1.4
The status of this port mirroring session. enable(1) - This session is active and all traffic from the source ports will be mirrored to the destination port. disable(2) - This session is not active. delete(3) - Remove the configuration for this Session
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2), delete(3)  

hmAgentDot3adAggPortTable 1.3.6.1.4.1.248.15.1.2.12
This table provides 802.3ad link aggregation information for each physical port that is not available through the standard MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmAgentDot3adAggPortEntry

hmAgentDot3adAggPortEntry 1.3.6.1.4.1.248.15.1.2.12.1
Information about a table entry. The hmAgentDot3adAggPort identifies the external interface number of the port.
Status: current Access: not-accessible
OBJECT-TYPE    
  HmAgentDot3adAggPortEntry  

hmAgentDot3adAggPort 1.3.6.1.4.1.248.15.1.2.12.1.1
ifIndex of this physical port
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hmAgentDot3adAggPortLACPMode 1.3.6.1.4.1.248.15.1.2.12.1.2
Enable/disable 802.3ad LACP on this port
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentPortConfigTable 1.3.6.1.4.1.248.15.1.2.13
A table of the switch's physical port config entries
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmAgentPortConfigEntry

hmAgentPortConfigEntry 1.3.6.1.4.1.248.15.1.2.13.1
Switch's physical port config entry
Status: current Access: not-accessible
OBJECT-TYPE    
  HmAgentPortConfigEntry  

hmAgentPortDot1dBasePort 1.3.6.1.4.1.248.15.1.2.13.1.1
The port number of this port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..65535  

hmAgentPortIfIndex 1.3.6.1.4.1.248.15.1.2.13.1.2
The switch's Port IfIndex
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hmAgentPortIanaType 1.3.6.1.4.1.248.15.1.2.13.1.3
The switch's Port Type
Status: current Access: read-only
OBJECT-TYPE    
  IANAifType  

hmAgentPortSTPMode 1.3.6.1.4.1.248.15.1.2.13.1.4
The switch's Port Spanning Tree Protocol Mode STP mode values are: dot1d (the default) fast, indicates you want to use the fast spanning tree mode off, indicates the STP mode is turned off for a particular port This object is only supported when the Dot1d Protocol is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER dot1d(1), fast(2), off(3)  

hmAgentPortSTPState 1.3.6.1.4.1.248.15.1.2.13.1.5
The switch's Port Spanning Tree Protocol State. This object is only supported when the Dot1d Protocol is enabled.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER blocking(1), listening(2), learning(3), forwarding(4), disabled(5)  

hmAgentPortAdminMode 1.3.6.1.4.1.248.15.1.2.13.1.6
The switch's Port Admin Mode
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentPortPhysicalMode 1.3.6.1.4.1.248.15.1.2.13.1.7
The switch's Port Speed Mode. This is the configured physical mode. This object is read-only for gigabit ports
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER auto-negotiate(1), half-10(2), full-10(3), half-100(4), full-100(5), half-100fx(6), full-100fx(7), full-1000sx(8)  

hmAgentPortPhysicalStatus 1.3.6.1.4.1.248.15.1.2.13.1.8
The switch's Port Physical Speed Status. This is the current actual speed.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER auto-negotiate(1), half-10(2), full-10(3), half-100(4), full-100(5), half-100fx(6), full-100fx(7), full-1000sx(8)  

hmAgentPortLinkTrapMode 1.3.6.1.4.1.248.15.1.2.13.1.9
If enabled, link up and link down traps will be sent for this port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentPortClearStats 1.3.6.1.4.1.248.15.1.2.13.1.10
clear stats for this port only
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentPortDefaultType 1.3.6.1.4.1.248.15.1.2.13.1.11
This object identifies the default administrative port type, to be used in conjunction with the operational port type denoted by hmAgentPortType. The set of possible values for this object is the same as the set defined for the hmAgentPortType object. This object represents the administratively-configured type of the MAU. If auto-negotiation is not enabled or is not implemented for this MAU, the value of this object determines the operational type of the MAU. In this case, a set to this object will force the MAU into the specified operating mode. If auto-negotiation is implemented and enabled for this MAU, the operational type of the MAU is determined by auto-negotiation, and the value of this object denotes the type to which the MAU will automatically revert if/when auto-negotiation is later disabled. The valid values for this object are: dot3MauType10BaseTHD dot3MauType10BaseTFD dot3MauType100BaseTXHD dot3MauType100BaseTXFD dot3MauType100BaseFXFD dot3MauType1000BaseSXFD
Status: current Access: read-write
OBJECT-TYPE    
  OBJECT IDENTIFIER  

hmAgentPortType 1.3.6.1.4.1.248.15.1.2.13.1.12
This object identifies the port type. An initial set of MAU types are defined in RFC 2668. The assignment of OBJECT IDENTIFIERs to new types of MAUs is managed by the IANA. If the MAU type is unknown, the object identifier unknownMauType OBJECT IDENTIFIER ::= { 0 0 } is returned. Note that unknownMauType is a syntactically valid object identifier, and any conformant implementation of ASN.1 and the BER must be able to generate and recognize this value. This object represents the operational type of the MAU, as determined by either (1) the result of the auto-negotiation function or (2) if auto-negotiation is not enabled or is not implemented for this MAU, by the value of the object hmAgentPortDefaultType, or (3) for the GigE card a value determined by the GBIC connected to the card. In case (2), a set to the object hmAgentPortDefaultType will force the MAU into the new operating mode. The valid values for this object are: dot3MauType10BaseTHD dot3MauType10BaseTFD dot3MauType100BaseTXHD dot3MauType100BaseTXFD dot3MauType100BaseFXFD dot3MauType1000BaseSXFD dot3MauType1000BaseTFD
Status: current Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER  

hmAgentPortAutoNegAdminStatus 1.3.6.1.4.1.248.15.1.2.13.1.13
This object identifies the administration status of auto negotiation for this port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentPortDot3FlowControlMode 1.3.6.1.4.1.248.15.1.2.13.1.14
Config flowcontrol allows you to enable or disable 802.3x flow control for this port. This value applies to only full-duplex mode ports.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentPortDVlanTagMode 1.3.6.1.4.1.248.15.1.2.13.1.15
Controls the Double Vlan Tag mode on this port. Default is normal(2).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER core(1), normal(2), access(3)  

hmAgentPortDVlanTagEthertype 1.3.6.1.4.1.248.15.1.2.13.1.16
Configures the Double Vlan Tag Ethertype for this port. If this object is supported, ethertype cannot be configured globally for the switch. Commonly used are the Ethertypes for vman tags (34984, or 0x88A8) and dot1q tags (33024, or 0x8100).
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

hmAgentPortDVlanTagCustomerId 1.3.6.1.4.1.248.15.1.2.13.1.17
Configures the Customer ID for the Double Vlan Tag for this port.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hmAgentPortMaxFrameSizeLimit 1.3.6.1.4.1.248.15.1.2.13.1.18
This object identifies the largest value that can be configured for hmAgentPortMaxFrameSize
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hmAgentPortMaxFrameSize 1.3.6.1.4.1.248.15.1.2.13.1.19
This object identifies the currently configured maximum frame size value for this port. The maximmum value that this object can be set to is the value of hmAgentPortMaxFrameSizeLimit. For Ethernet ports which support 802.1Q vlan tagging, the minimum value that this object can be set to is 1522
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hmAgentPortVoiceVlanMode 1.3.6.1.4.1.248.15.1.2.13.1.20
Describes and Configures the Port Voice VLAN Mode.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), vlanid(2), dot1p(3), vlanidanddot1p(4), untagged(5), disable(6)  

hmAgentPortVoiceVlanID 1.3.6.1.4.1.248.15.1.2.13.1.21
Describes and Configures the Port Voice VLAN ID if the Voice Vlan Mode is Vlan ID.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..4093  

hmAgentPortVoiceVlanPriority 1.3.6.1.4.1.248.15.1.2.13.1.22
Describes and Configures the Port Voice VLAN Priority if the Voice Vlan Mode is dot1p. A value of 255 indicates that the priority is not configured.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7 | 255  

hmAgentPortVoiceVlanDataPriorityMode 1.3.6.1.4.1.248.15.1.2.13.1.23
Describes and Configures the Port Voice VLAN Data Priority Mode.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER trust(1), untrust(2)  

hmAgentPortVoiceVlanOperationalStatus 1.3.6.1.4.1.248.15.1.2.13.1.24
Describes the Port Voice VLAN Operational Status.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

hmAgentPortVoiceVlanDSCP 1.3.6.1.4.1.248.15.1.2.13.1.25
Describes and Configures the Port Voice VLAN DSCP value.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hmAgentPortVoiceVlanAuthMode 1.3.6.1.4.1.248.15.1.2.13.1.26
Describes and Configures the Port Voice VLAN Authentication mode. Disable means authentication not required for voice devices when dot1x is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentProtocolConfigGroup 1.3.6.1.4.1.248.15.1.2.14
OBJECT IDENTIFIER    

hmAgentProtocolGroupCreate 1.3.6.1.4.1.248.15.1.2.14.1
Set to non-empty string to create a Protocol-Based VLAN group.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..16)  

hmAgentProtocolGroupTable 1.3.6.1.4.1.248.15.1.2.14.2
A table of the switch's Protocol-based VLAN entries
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmAgentProtocolGroupEntry

hmAgentProtocolGroupEntry 1.3.6.1.4.1.248.15.1.2.14.2.1
Switch's Protocol-based VLAN entry
Status: current Access: not-accessible
OBJECT-TYPE    
  HmAgentProtocolGroupEntry  

hmAgentProtocolGroupId 1.3.6.1.4.1.248.15.1.2.14.2.1.1
Group identifier of the Protocol-based VLAN entry.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hmAgentProtocolGroupName 1.3.6.1.4.1.248.15.1.2.14.2.1.2
Group name of the Protocol-based VLAN entry.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

hmAgentProtocolGroupVlanId 1.3.6.1.4.1.248.15.1.2.14.2.1.3
VLAN associated with the Protocol-based VLAN entry. Set to 0 to remove.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hmAgentProtocolGroupProtocolIP 1.3.6.1.4.1.248.15.1.2.14.2.1.4
The status of the IP protocol association with the Protocol-based VLAN entry.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentProtocolGroupProtocolARP 1.3.6.1.4.1.248.15.1.2.14.2.1.5
The status of the ARP protocol association with the Protocol-based VLAN entry.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentProtocolGroupProtocolIPX 1.3.6.1.4.1.248.15.1.2.14.2.1.6
The status of the IPX protocol association with the Protocol-based VLAN entry.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentProtocolGroupStatus 1.3.6.1.4.1.248.15.1.2.14.2.1.7
The status of the Protocol-based VLAN entry. active(1) - this entry is active destroy(6) - remove this entry
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

hmAgentProtocolGroupPortTable 1.3.6.1.4.1.248.15.1.2.14.3
A table of the switch's physical port config entries
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmAgentProtocolGroupPortEntry

hmAgentProtocolGroupPortEntry 1.3.6.1.4.1.248.15.1.2.14.3.1
Switch's physical port config entry
Status: current Access: not-accessible
OBJECT-TYPE    
  HmAgentProtocolGroupPortEntry  

hmAgentProtocolGroupPortIfIndex 1.3.6.1.4.1.248.15.1.2.14.3.1.1
The interface number of this instance.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hmAgentProtocolGroupPortStatus 1.3.6.1.4.1.248.15.1.2.14.3.1.2
The status of this entry. active(1) - the port is associated with this group createAndGo(4) - add the port to this group createAndWait(5) - add the port to this group destroy(6) - remove the port from this group
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hmAgentStpSwitchConfigGroup 1.3.6.1.4.1.248.15.1.2.15
OBJECT IDENTIFIER    

hmAgentStpConfigDigestKey 1.3.6.1.4.1.248.15.1.2.15.1
The MST configuration digest key.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(16)  

hmAgentStpConfigFormatSelector 1.3.6.1.4.1.248.15.1.2.15.2
The MST configuration format selector. A value other than 0 (zero) indicates non-support for the IEEE 802.1s standard.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..255  

hmAgentStpConfigName 1.3.6.1.4.1.248.15.1.2.15.3
The MST configuration name of at most 32 characters.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..32)  

hmAgentStpConfigRevision 1.3.6.1.4.1.248.15.1.2.15.4
The MST configuration revision. The default value is 1.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..65535  

hmAgentStpForceVersion 1.3.6.1.4.1.248.15.1.2.15.5
The MST configuration force protocol version. The default version is dot1w.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER dot1d(1), dot1w(2), dot1s(3)  

hmAgentStpAdminMode 1.3.6.1.4.1.248.15.1.2.15.6
The spanning tree operational status. enable(1) - enables spanning tree operational status on the switch. disable(2) - disables spanning tree operational status on the switch. The default status is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentStpBpduGuardMode 1.3.6.1.4.1.248.15.1.2.15.13
The spanning tree BPDU Guard Mode. enable(1) - enables BPDU Guard Mode on the switch. disable(2) - disables BPDU Guard Mode on the switch. The default status is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentStpBpduFilterDefault 1.3.6.1.4.1.248.15.1.2.15.14
The spanning tree BPDU Filter Mode, it enables BPDU Filter on all edge ports. enable(1) - enables BPDU Filter Mode on the switch. disable(2) - disables BPDU Filter Mode on the switch. The default status is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentStpPortTable 1.3.6.1.4.1.248.15.1.2.15.7
STP port table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmAgentStpPortEntry

hmAgentStpPortEntry 1.3.6.1.4.1.248.15.1.2.15.7.1
STP port entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  HmAgentStpPortEntry  

hmAgentStpPortState 1.3.6.1.4.1.248.15.1.2.15.7.1.1
The administrative STP state for the port. enable(1) - enables STP on the port. disable(2) - disables STP on the port. The default port STP state is enabled for the first 4095 ports and disabled for any ports beyond.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentStpPortStatsMstpBpduRx 1.3.6.1.4.1.248.15.1.2.15.7.1.2
The MSTP BPDUs received on a specific port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hmAgentStpPortStatsMstpBpduTx 1.3.6.1.4.1.248.15.1.2.15.7.1.3
The MSTP BPDUs sent from a specific port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hmAgentStpPortStatsRstpBpduRx 1.3.6.1.4.1.248.15.1.2.15.7.1.4
The RSTP BPDUs received on a specific port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hmAgentStpPortStatsRstpBpduTx 1.3.6.1.4.1.248.15.1.2.15.7.1.5
The RSTP BPDUs sent from a specific port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hmAgentStpPortStatsStpBpduRx 1.3.6.1.4.1.248.15.1.2.15.7.1.6
The STP BPDUs received on a specific port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hmAgentStpPortStatsStpBpduTx 1.3.6.1.4.1.248.15.1.2.15.7.1.7
The STP BPDUs sent from a specific port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hmAgentStpPortUpTime 1.3.6.1.4.1.248.15.1.2.15.7.1.8
Time since port was reset. It is displayed in days, hours, minutes, and seconds.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

hmAgentStpPortMigrationCheck 1.3.6.1.4.1.248.15.1.2.15.7.1.9
Force the specified port to transmit RSTP or MSTP BPDU's. Supported values: false(0) - BPDUs are not to be transmitted. true(1) - BPDUs are to be transmitted A non-zero value indicates that BPDUs are to be sent on the specified port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER false(0), true(1)  

hmAgentStpPortHelloTime 1.3.6.1.4.1.248.15.1.2.15.7.1.10
Hello time for the STP port. The default value is 2.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..2  

hmAgentStpCstConfigGroup 1.3.6.1.4.1.248.15.1.2.15.8
OBJECT IDENTIFIER    

hmAgentStpCstHelloTime 1.3.6.1.4.1.248.15.1.2.15.8.1
The MSTP root port hello time for the CIST.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hmAgentStpCstMaxAge 1.3.6.1.4.1.248.15.1.2.15.8.2
The MSTP root port max age for the CIST.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hmAgentStpCstRegionalRootId 1.3.6.1.4.1.248.15.1.2.15.8.3
The MSTP regional root identifier for the CIST.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(8)  

hmAgentStpCstRegionalRootPathCost 1.3.6.1.4.1.248.15.1.2.15.8.4
The MSTP regional root path cost for the CIST.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hmAgentStpCstRootFwdDelay 1.3.6.1.4.1.248.15.1.2.15.8.5
The MSTP root port forward delay for the CIST.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hmAgentStpCstBridgeFwdDelay 1.3.6.1.4.1.248.15.1.2.15.8.6
The MSTP bridge forward delay for the CIST. The default value is 15.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 4..30  

hmAgentStpCstBridgeHelloTime 1.3.6.1.4.1.248.15.1.2.15.8.7
The MSTP bridge hello time for the CIST. The default value is 2.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..2  

hmAgentStpCstBridgeHoldTime 1.3.6.1.4.1.248.15.1.2.15.8.8
The MSTP bridge hold time for the CIST.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hmAgentStpCstBridgeMaxAge 1.3.6.1.4.1.248.15.1.2.15.8.9
The MSTP bridge max age for the CIST. The default value is 20.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 6..40  

hmAgentStpCstBridgeDesignatedRoot 1.3.6.1.4.1.248.15.1.2.15.8.10
The Designated Root like in dot1dStpDesignatedRoot.
Status: current Access: read-only
OBJECT-TYPE    
  BridgeId  

hmAgentStpCstBridgePriority 1.3.6.1.4.1.248.15.1.2.15.8.11
The MSTP bridge priority for the CIST. The default value is 32768.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..61440  

hmAgentStpCstBridgeTimeSinceTopologyChange 1.3.6.1.4.1.248.15.1.2.15.8.12
The time (in hundredths of a second) since the last time a topology change was detected by the bridge entity.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

hmAgentStpCstBridgeTopChanges 1.3.6.1.4.1.248.15.1.2.15.8.13
The total number of topology changes detected by this bridge since the management entity was last reset or initialized.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hmAgentStpCstBridgeRootCost 1.3.6.1.4.1.248.15.1.2.15.8.14
The cost of the path to the root as seen from this bridge.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hmAgentStpCstBridgeRootPort 1.3.6.1.4.1.248.15.1.2.15.8.15
The port number of the port which offers the lowest cost path from this bridge to the root bridge.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hmAgentStpCstBridgeMaxHops 1.3.6.1.4.1.248.15.1.2.15.8.16
The MSTP bridge max hops for the CIST. The default value is 20.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 6..40  

hmAgentStpCstBridgeHoldCount 1.3.6.1.4.1.248.15.1.2.15.8.17
The MSTP bridge hold count for the CIST. This command sets the value of maximum bpdus that a bridge is allowed to send within a hello time window. The default value is 10.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..40  

hmAgentStpCstPortTable 1.3.6.1.4.1.248.15.1.2.15.9
CIST port table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmAgentStpCstPortEntry

hmAgentStpCstPortEntry 1.3.6.1.4.1.248.15.1.2.15.9.1
CIST port entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  HmAgentStpCstPortEntry  

hmAgentStpCstPortOperEdge 1.3.6.1.4.1.248.15.1.2.15.9.1.1
The MSTP operational status of a specific port for the CIST.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER true(1), false(2)  

hmAgentStpCstPortOperPointToPoint 1.3.6.1.4.1.248.15.1.2.15.9.1.2
The MSTP operational point to point mac of a specific port for the CIST.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER true(1), false(2)  

hmAgentStpCstPortTopologyChangeAck 1.3.6.1.4.1.248.15.1.2.15.9.1.3
The MSTP topology change acknowledge for a specific port in the CIST.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER true(1), false(2)  

hmAgentStpCstPortEdge 1.3.6.1.4.1.248.15.1.2.15.9.1.4
The administrative state of a specific port in CIST. true(1) - port is edge port. false(2) - port is auto-edge or no edge port. The default port state is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2)  

hmAgentStpCstPortForwardingState 1.3.6.1.4.1.248.15.1.2.15.9.1.5
The MSTP forwarding state of a specific port in CIST.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER discarding(1), learning(2), forwarding(3), disabled(4), manualFwd(5), notParticipate(6)  

hmAgentStpCstPortId 1.3.6.1.4.1.248.15.1.2.15.9.1.6
The MSTP port identifier of a specific port in CIST.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

hmAgentStpCstPortPathCost 1.3.6.1.4.1.248.15.1.2.15.9.1.7
The MSTP port path cost in CIST. The default value will correspond to the recommendation specified in IEEE 802.1s Table 13-2 which varies depending upon link speed.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..200000000  

hmAgentStpCstPortPriority 1.3.6.1.4.1.248.15.1.2.15.9.1.8
The MSTP port priority in CIST. The priority is in the increments of 16. The default value is 128.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..240  

hmAgentStpCstDesignatedBridgeId 1.3.6.1.4.1.248.15.1.2.15.9.1.9
The MSTP designated bridge ID of a specific port in CIST.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(8)  

hmAgentStpCstDesignatedCost 1.3.6.1.4.1.248.15.1.2.15.9.1.10
The MSTP designated cost of a specific port in CIST.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hmAgentStpCstDesignatedPortId 1.3.6.1.4.1.248.15.1.2.15.9.1.11
The MSTP designated port ID of a specific port in CIST.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2)  

hmAgentStpCstExtPortPathCost 1.3.6.1.4.1.248.15.1.2.15.9.1.12
The MSTP external port path cost in CIST. The default value varies depending upon the link speed.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..200000000  

hmAgentStpCstPortAutoEdge 1.3.6.1.4.1.248.15.1.2.15.9.1.13
The auto edge state of a specific port in CIST. true(1) - enables the port. false(2) - disables the port. The default port state is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2)  

hmAgentStpCstPortRole 1.3.6.1.4.1.248.15.1.2.15.9.1.14
The current Port Role for the Port (i.e., Root, Alternate, Designated, or Backup), for the CIST.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER root(1), alternate(2), designated(3), backup(4), master(5), disabled(6)  

hmAgentStpCstPortDisputed 1.3.6.1.4.1.248.15.1.2.15.9.1.15
The current value of the disputed variable for the CIST for the Port. A value of true(1) indicates that the disputed variable is set. A value of false(2) indicates that the agreed variable is cleared.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER true(1), false(2)  

hmAgentStpCstPortBpduGuardEffect 1.3.6.1.4.1.248.15.1.2.15.9.1.16
BPDU Guard Mode effect on the port. enable(1) - BPDU Guard Mode is enabled on the port. disable(2) - BPDU Guard Mode is disabled on the port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentStpCstPortBpduFilter 1.3.6.1.4.1.248.15.1.2.15.9.1.17
This command sets BPDU Filter mode on the port. enable(1) - BPDU Filter Mode is enabled on the port. disable(2) - BPDU Filter Mode is disabled on the port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentStpCstPortBpduFlood 1.3.6.1.4.1.248.15.1.2.15.9.1.18
This command sets BPDU Flood mode on the port. enable(1) - BPDU Flood Mode is enabled on the port. disable(2) - BPDU Flood Mode is disabled on the port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentStpCstPortRootGuard 1.3.6.1.4.1.248.15.1.2.15.9.1.19
This command sets a port to discard any superior information received by the port and thus protect against root of the device from changing.The port gets put into discarding state and does not forward any packets. enable(1) - enables the root-guard mode for the port. disable(2) - disables the root-guard mode for the port. The default root-guard mode is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentStpCstPortTCNGuard 1.3.6.1.4.1.248.15.1.2.15.9.1.20
This command restricts the port from propagating any topology change information received through that port. enable(1) - enables the tcn-guard mode for the port. disable(2) - disables the tcn-guard mode for the port. The default tcn-guard mode is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentStpCstPortLoopGuard 1.3.6.1.4.1.248.15.1.2.15.9.1.21
This command enables loop guard on this port. This setting applies to all Spanning Tree instances of which this port is a member. enable(1) - enables the loop guard mode for the port. disable(2) - disables the loop guard mode for the port. The default loop-guard mode is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentStpMstTable 1.3.6.1.4.1.248.15.1.2.15.10
MST table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmAgentStpMstEntry

hmAgentStpMstEntry 1.3.6.1.4.1.248.15.1.2.15.10.1
MST entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  HmAgentStpMstEntry  

hmAgentStpMstId 1.3.6.1.4.1.248.15.1.2.15.10.1.1
The MSTP instance ID.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hmAgentStpMstBridgePriority 1.3.6.1.4.1.248.15.1.2.15.10.1.2
The MSTP bridge priority in a specific instance. The priority is in the increments of 4096. The recommended default value is 32768.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..61440  

hmAgentStpMstBridgeIdentifier 1.3.6.1.4.1.248.15.1.2.15.10.1.3
The MSTP bridge identifier in a specific instance.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(8)  

hmAgentStpMstDesignatedRootId 1.3.6.1.4.1.248.15.1.2.15.10.1.4
The MSTP designated root bridge identifier in a specific instance.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(8)  

hmAgentStpMstRootPathCost 1.3.6.1.4.1.248.15.1.2.15.10.1.5
The MSTP root path cost in a specific instance.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hmAgentStpMstRootPortId 1.3.6.1.4.1.248.15.1.2.15.10.1.6
The MSTP root port ID in a specific instance.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

hmAgentStpMstTimeSinceTopologyChange 1.3.6.1.4.1.248.15.1.2.15.10.1.7
The MSTP time since the last topology change in a specific instance.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

hmAgentStpMstTopologyChangeCount 1.3.6.1.4.1.248.15.1.2.15.10.1.8
The MSTP count of topology changes in a specific instance.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hmAgentStpMstTopologyChangeParm 1.3.6.1.4.1.248.15.1.2.15.10.1.9
The MSTP topology change parameter in a specific instance.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER true(1), false(2)  

hmAgentStpMstRowStatus 1.3.6.1.4.1.248.15.1.2.15.10.1.10
The MSTP instance status. Supported values: active(1) - valid instance. createAndGo(4) - used to create a new instance. destroy(6) - removes an instance.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hmAgentStpMstPortTable 1.3.6.1.4.1.248.15.1.2.15.11
MST port table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmAgentStpMstPortEntry

hmAgentStpMstPortEntry 1.3.6.1.4.1.248.15.1.2.15.11.1
MST port entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  HmAgentStpMstPortEntry  

hmAgentStpMstPortForwardingState 1.3.6.1.4.1.248.15.1.2.15.11.1.1
The MSTP forwarding state of a specific port in a specific instance.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER discarding(1), learning(2), forwarding(3), disabled(4), manualFwd(5), notParticipate(6)  

hmAgentStpMstPortId 1.3.6.1.4.1.248.15.1.2.15.11.1.2
The MSTP port identifier of a specific port in a specific instance.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

hmAgentStpMstPortPathCost 1.3.6.1.4.1.248.15.1.2.15.11.1.3
The MSTP port path cost in a specific instance. The default value will correspond to the recommendation specified in IEEE 802.1s Table 13-2 which varies depending upon link speed.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..200000000  

hmAgentStpMstPortPriority 1.3.6.1.4.1.248.15.1.2.15.11.1.4
The MSTP port priority in a specific instance. The priority is in the increments of 16. The default value is 128.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..240  

hmAgentStpMstDesignatedBridgeId 1.3.6.1.4.1.248.15.1.2.15.11.1.5
The MSTP designated bridge ID of a specific port in a specific instance.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(8)  

hmAgentStpMstDesignatedCost 1.3.6.1.4.1.248.15.1.2.15.11.1.6
The MSTP designated cost of a specific port in a specific instance.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hmAgentStpMstDesignatedPortId 1.3.6.1.4.1.248.15.1.2.15.11.1.7
The MSTP designated port ID of a specific port in a specific instance.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2)  

hmAgentStpMstPortRole 1.3.6.1.4.1.248.15.1.2.15.11.1.8
In an MSTP Bridge, the current Port Role for the Port (i.e., Root, Alternate, Designated, or Backup), for the MSTI.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER root(1), alternate(2), designated(3), backup(4), master(5), disabled(6)  

hmAgentStpMstPortDisputed 1.3.6.1.4.1.248.15.1.2.15.11.1.9
In an MSTP Bridge, the current value of the disputed variable for the MSTI for the Port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER true(1), false(2)  

hmAgentStpMstPortLoopInconsistentState 1.3.6.1.4.1.248.15.1.2.15.11.1.10
The loop inconsistent state of a specific port in a specific instance. This value can only report as true(1) when loop guard is enabled on the port and the port has transitioned from blocking state in this MST instance.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER false(0), true(1)  

hmAgentStpMstPortTransitionsIntoLoopInconsistentState 1.3.6.1.4.1.248.15.1.2.15.11.1.11
The number of times this interface has transitioned into loop inconsistent state.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hmAgentStpMstPortTransitionsOutOfLoopInconsistentState 1.3.6.1.4.1.248.15.1.2.15.11.1.12
The number of times this interface has transitioned out of loop inconsistent state.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hmAgentStpMstReceivedBridgeId 1.3.6.1.4.1.248.15.1.2.15.11.1.13
The MSTP received bridge ID on a specific port in a specific instance.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(8)  

hmAgentStpMstReceivedRPC 1.3.6.1.4.1.248.15.1.2.15.11.1.14
The MSTP received root path cost of a specific port in a specific instance.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hmAgentStpMstReceivedPortId 1.3.6.1.4.1.248.15.1.2.15.11.1.15
The MSTP received port ID on a specific port in a specific instance.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2)  

hmAgentStpMstVlanTable 1.3.6.1.4.1.248.15.1.2.15.12
MST VLAN table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmAgentStpMstVlanEntry

hmAgentStpMstVlanEntry 1.3.6.1.4.1.248.15.1.2.15.12.1
MST VLAN entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  HmAgentStpMstVlanEntry  

hmAgentStpMstVlanRowStatus 1.3.6.1.4.1.248.15.1.2.15.12.1.1
The association status of an MSTP instance and a VLAN. Supported values: active(1) - valid association between an MSTP instance and a VLAN. createAndGo(4) - used to create a new association between an MSTP instance and a VLAN. destroy(6) - removes the association between an MSTP instance and a VLAN.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hmAgentClassOfServiceGroup 1.3.6.1.4.1.248.15.1.2.17
OBJECT IDENTIFIER    

hmAgentClassOfServicePortTable 1.3.6.1.4.1.248.15.1.2.17.1
A table that contains information about the 802.1p priority mapping to traffic class priority queue for every physical port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmAgentClassOfServicePortEntry

hmAgentClassOfServicePortEntry 1.3.6.1.4.1.248.15.1.2.17.1.1
A 802.1p priority mapped to a traffic class priority queue.
Status: current Access: not-accessible
OBJECT-TYPE    
  HmAgentClassOfServicePortEntry  

hmAgentClassOfServicePortPriority 1.3.6.1.4.1.248.15.1.2.17.1.1.1
The Priority value determined for the received frame. This value is equivalent to the priority indicated in the tagged frame received, or one of the evaluated priorities, determined according to the media-type. For untagged frames received from Ethernet media, this value is equal to the dot1dPortDefaultUserPriority value for the ingress port.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..7  

hmAgentClassOfServicePortClass 1.3.6.1.4.1.248.15.1.2.17.1.1.2
Traffic class priority queue the received frame is mapped to. The possible range depends on the number of supported traffic classes for the appropriate port, as shown in dot1dPortNumTrafficClasses.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..7  

hmAgentSystemGroup 1.3.6.1.4.1.248.15.1.3
OBJECT IDENTIFIER    

hmAgentSaveConfig 1.3.6.1.4.1.248.15.1.3.1
Enable hmAgentSaveConfig will initiate an configuration save to nvram. Disable hmAgentSaveConfig after a configuration save will reset hmAgentSaveConfigStatus back to notInitiated state.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentClearConfig 1.3.6.1.4.1.248.15.1.3.2
clear config to factory defaults
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentClearLags 1.3.6.1.4.1.248.15.1.3.3
clear lag configuration
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentClearLoginSessions 1.3.6.1.4.1.248.15.1.3.4
close all telnet sessions
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentClearPasswords 1.3.6.1.4.1.248.15.1.3.5
reset passwords
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentClearPortStats 1.3.6.1.4.1.248.15.1.3.6
clear all port statistics
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentClearSwitchStats 1.3.6.1.4.1.248.15.1.3.7
clear all switch statistics
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentClearTrapLog 1.3.6.1.4.1.248.15.1.3.8
clear trap log
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentClearVlan 1.3.6.1.4.1.248.15.1.3.9
clear vlan entries
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentResetSystem 1.3.6.1.4.1.248.15.1.3.10
reset the switch
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentSaveConfigStatus 1.3.6.1.4.1.248.15.1.3.11
Indicates the current status of an save configuration request.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notInitiated(1), savingInProcess(2), savingComplete(3)  

hmAgentCableTesterGroup 1.3.6.1.4.1.248.15.1.4
OBJECT IDENTIFIER    

hmAgentCableTesterStatus 1.3.6.1.4.1.248.15.1.4.1
Status of the Virtual Cable Tester active(1) - cable testing is in progress. Set to this value to start the test. success(2) - A successful test was performed. Cannot be set. failure(3) - A failure was encountered during the test. Cannot be set. uninitialized(4) - No test has been performed yet. Cannot be set.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER active(1), success(2), failure(3), uninitialized(4)  

hmAgentCableTesterIfIndex 1.3.6.1.4.1.248.15.1.4.2
Determines on which port to perform the cable test. Limited to copper based ports.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

hmAgentCableTesterCableStatus 1.3.6.1.4.1.248.15.1.4.3
Indicates the results of the Cable Test. normal(1) - The cable is working correctly. open(2) - The cable is disconnected or there is a faulty connector. short(3) - There is an electrical short in the cable. unknown(4) - No test has been performed yet, or a test is currently in progress.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER normal(1), open(2), short(3), unknown(4)  

hmAgentCableTesterMinimumCableLength 1.3.6.1.4.1.248.15.1.4.4
The estimated length of the cable in meters. This value indicates the shortest length estimated. This object will return 0 if hmAgentCableTesterStatus is not success(2) or the cable length is unknown.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hmAgentCableTesterMaximumCableLength 1.3.6.1.4.1.248.15.1.4.5
The estimated length of the cable in meters. This value indicates the longest length estimated. This object will return 0 if hmAgentCableTesterStatus is not success(2) or the cable length is unknown.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hmAgentCableTesterCableFailureLocation 1.3.6.1.4.1.248.15.1.4.6
The estimated distance in meters from the end of the cable to the failure location. This object will return 0 if hmAgentCableTesterStatus is not success(2).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hmAgentMgmtSecurity 1.3.6.1.4.1.248.15.11
OBJECT IDENTIFIER    

hmAgentSSHConfigGroup 1.3.6.1.4.1.248.15.11.2
OBJECT IDENTIFIER    

hmAgentSSHAdminMode 1.3.6.1.4.1.248.15.11.2.1
Configures whether the SSH service is enabled on this switch. The default value is disable(2).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentSSHProtocolLevel 1.3.6.1.4.1.248.15.11.2.2
Configures which protocol versions of SSH are enabled on this switch. The default value is both(3).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER ssh10(1), ssh20(2), both(3)  

hmAgentSSHSessionsCount 1.3.6.1.4.1.248.15.11.2.3
Current number of active SSH sessions on this switch.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hmAgentSSHMaxSessionsCount 1.3.6.1.4.1.248.15.11.2.4
Max number of SSH sessions permitted on this switch.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..5  

hmAgentSSHSessionTimeout 1.3.6.1.4.1.248.15.11.2.5
ssh idle timeout value for this switch im minutes.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..160  

hmRadius 1.3.6.1.4.1.248.15.8
OBJECT IDENTIFIER    

hmAgentRadiusConfigGroup 1.3.6.1.4.1.248.15.8.1
OBJECT IDENTIFIER    

hmAgentRadiusMaxTransmit 1.3.6.1.4.1.248.15.8.1.1
Maximum number of retransmissions of a RADIUS request packet
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..15  

hmAgentRadiusTimeout 1.3.6.1.4.1.248.15.8.1.2
Time out duration (in seconds) before packets are retransmitted
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..30  

hmAgentRadiusAccountingMode 1.3.6.1.4.1.248.15.8.1.3
Identifies if RADIUS Accounting has been enabled or not
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentRadiusStatsClear 1.3.6.1.4.1.248.15.8.1.4
When set to enable(1), all Radius statistics will be reset.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentRadiusAccountingIndexNextValid 1.3.6.1.4.1.248.15.8.1.5
Indicates the next valid index into the hmAgentRadiusAccountingConfigTable for creation. If no additional entries are allowed, this will be 0.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0 | 1..2147483647  

hmAgentRadiusAccountingConfigTable 1.3.6.1.4.1.248.15.8.1.6
Table with information about Radius Accounting Server IP Addresses, port numbers and shared secret. Only one entry is supported at this time.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmAgentRadiusAccountingConfigEntry

hmAgentRadiusAccountingConfigEntry 1.3.6.1.4.1.248.15.8.1.6.1
Entry consisting of configuration data for a Radius Accounting Server.
Status: current Access: not-accessible
OBJECT-TYPE    
  HmAgentRadiusAccountingConfigEntry  

hmAgentRadiusAccountingServerIndex 1.3.6.1.4.1.248.15.8.1.6.1.1
Unique index of the configured RADIUS accounting server. The next valid value of this object for creation is specified by hmAgentRadiusAccountingIndexNextValid.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2147483647  

hmAgentRadiusAccountingServerAddress 1.3.6.1.4.1.248.15.8.1.6.1.2
IP Address of the configured RADIUS accounting server. This object cannot be changed after creation.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

hmAgentRadiusAccountingPort 1.3.6.1.4.1.248.15.8.1.6.1.3
Port number for the RADIUS accounting server.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..65535  

hmAgentRadiusAccountingSecret 1.3.6.1.4.1.248.15.8.1.6.1.4
Configured shared sercret for the RADIUS accounting server.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..20)  

hmAgentRadiusAccountingStatus 1.3.6.1.4.1.248.15.8.1.6.1.5
Creates or destroys a RADIUS accounting server entry. During creation, the next available index is specified by the hmAgentRadiusAccountingIndexNextValid object. Rows creation using a different value for hmAgentRadiusAccountingServerIndex will fail. active(1) - This entry is active. createAndGo(4) - Creates a new entry. destroy(6) - Deletes an entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hmAgentRadiusServerIndexNextValid 1.3.6.1.4.1.248.15.8.1.7
Indicates the next valid index into the hmAgentRadiusServerConfigTable for creation. If no additional entries are allowed, this will be 0.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0 | 1..2147483647  

hmAgentRadiusServerConfigTable 1.3.6.1.4.1.248.15.8.1.8
Table with information about Radius Authentication Server IP Addresses, port numbers and shared secret
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmAgentRadiusServerConfigEntry

hmAgentRadiusServerConfigEntry 1.3.6.1.4.1.248.15.8.1.8.1
Entry consisting of configuration data for a Radius Authentication Server.
Status: current Access: not-accessible
OBJECT-TYPE    
  HmAgentRadiusServerConfigEntry  

hmAgentRadiusServerIndex 1.3.6.1.4.1.248.15.8.1.8.1.1
Unique index of the configured RADIUS server
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2147483647  

hmAgentRadiusServerAddress 1.3.6.1.4.1.248.15.8.1.8.1.2
IP Address of the configured RADIUS server. This object cannot be changed after creation.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

hmAgentRadiusServerPort 1.3.6.1.4.1.248.15.8.1.8.1.3
Port number for the RADIUS server.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..65535  

hmAgentRadiusServerSecret 1.3.6.1.4.1.248.15.8.1.8.1.4
Configured shared sercret for the RADIUS server.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..20)  

hmAgentRadiusServerPrimaryMode 1.3.6.1.4.1.248.15.8.1.8.1.5
Configure the RADIUS server to be the primary server. If there is any other server that is configured to be primary, that server is set to be a seconday server and this entry is set Primary.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentRadiusServerCurrentMode 1.3.6.1.4.1.248.15.8.1.8.1.6
Indicate if the RADIUS server is the current server in user for authentication.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

hmAgentRadiusServerMsgAuth 1.3.6.1.4.1.248.15.8.1.8.1.7
Enable or disable the message authenticator attribute for this RADIUS server.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentRadiusServerStatus 1.3.6.1.4.1.248.15.8.1.8.1.8
Creates or destroys a RADIUS Authentication server entry. During creation, the next available index is specified by the hmAgentRadiusServerIndexNextValid object. Rows creation using a different value for hmAgentRadiusServerIndex will fail. active(1) - This entry is active. createAndGo(4) - Creates a new entry. destroy(6) - Deletes an entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hmPlatform4OutboundTelnetPrivate 1.3.6.1.4.1.248.15.19
OBJECT IDENTIFIER    

hmAgentOutboundTelnetGroup 1.3.6.1.4.1.248.15.19.1
OBJECT IDENTIFIER    

hmAgentOutboundTelnetAdminMode 1.3.6.1.4.1.248.15.19.1.1
Admin-mode of the Outbound Telnet.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentOutboundTelnetMaxNoOfSessions 1.3.6.1.4.1.248.15.19.1.2
The maximum no. of Outbound Telnet sessions allowed.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..5  

hmAgentOutboundTelnetTimeout 1.3.6.1.4.1.248.15.19.1.3
The login inactivity timeout value for Outbound Telnet.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..160  

hmAgentSwitchVoiceVLANGroup 1.3.6.1.4.1.248.15.1.2.8.25
OBJECT IDENTIFIER    

hmAgentSwitchVoiceVLANAdminMode 1.3.6.1.4.1.248.15.1.2.8.25.1
This enables or disables Voice VLAN on the system.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentSwitchVoiceVlanDeviceTable 1.3.6.1.4.1.248.15.1.2.8.25.2
A table of the Voice Vlan device entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmAgentSwitchVoiceVlanDeviceEntry

hmAgentSwitchVoiceVlanDeviceEntry 1.3.6.1.4.1.248.15.1.2.8.25.2.1
Represents entry for a Voice Device on the interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  HmAgentSwitchVoiceVlanDeviceEntry  

hmAgentSwitchVoiceVlanInterfaceNum 1.3.6.1.4.1.248.15.1.2.8.25.2.1.1
The interface number of this interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..65535  

hmAgentSwitchVoiceVlanDeviceMacAddress 1.3.6.1.4.1.248.15.1.2.8.25.2.1.2
The Voice Device Mac address
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

hmAgentDot1xAdvanced 1.3.6.1.4.1.248.15.36
OBJECT IDENTIFIER    

hmAgentDot1xEnhancementConfigGroup 1.3.6.1.4.1.248.15.36.1
OBJECT IDENTIFIER    

hmAgentDot1xRadiusVlanAssignment 1.3.6.1.4.1.248.15.36.1.1
Enable/Disable dot1x Vlan Assignment Support on the switch.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentDot1xDynamicVlanCreationMode 1.3.6.1.4.1.248.15.36.1.2
Enable/Disable dot1x dynamic vlan creation Support on the switch.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentDot1xSafeVlanMode 1.3.6.1.4.1.248.15.36.1.3
Enable/Disable dot1x safe vlan assignment on the switch for multi-client authentication.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentDot1xPortConfigGroup 1.3.6.1.4.1.248.15.36.2
OBJECT IDENTIFIER    

hmAgentDot1xPortConfigTable 1.3.6.1.4.1.248.15.36.2.1
A table for dot1x enhanced Port details and associated functionality.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmAgentDot1xPortConfigEntry

hmAgentDot1xPortConfigEntry 1.3.6.1.4.1.248.15.36.2.1.1
Represents entry for port config table.
Status: current Access: not-accessible
OBJECT-TYPE    
  HmAgentDot1xPortConfigEntry  

hmAgentDot1xPortControlMode 1.3.6.1.4.1.248.15.36.2.1.1.1
Dot1x port control mode of this port.The Port control mode . The port control mode for this interface can take the following values , force-unauthorized - the port is in unauthorized mode, auto-Port based mode. If a client authenticates suscessfully, then the interface is authorized . Otherwise, the port is in unauthorized mode. If more than one clients are attached to the port , then only one client needs to authenticate to allow other clients access. force-authorized - The port is placed in authorized mode macBased - If more than one client is attached to the port, then each client needs to authenticate separately. This object depcreates dot1xAuthAuthControlledPortControl object in IEEE8021-PAE-MIB
Status: current Access: read-write
OBJECT-TYPE    
  HmAgentDot1xPortControlMode  

hmAgentDot1xGuestVlanId 1.3.6.1.4.1.248.15.36.2.1.1.2
Specifies the Guest Vlan of the port. A port will be moved to its Guest Vlan if no client sucessfully authenticates on that port for the Guest Vlan Period. A value of zero indicates no Guest Vlan is configured for the interface.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

hmAgentDot1xGuestVlanPeriod 1.3.6.1.4.1.248.15.36.2.1.1.3
The value, in seconds, of the guestVlanPeriod constant currently in use for Guest Vlan Assignment for the port .
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..65535  

hmAgentDot1xUnauthenticatedVlan 1.3.6.1.4.1.248.15.36.2.1.1.4
Specifies the Unauthenticated Vlan of the port. A port will be moved to its unauthenticated Vlan if the client authenticates unsucessfully on that port . A value of zero indicates no Unauthenticated Vlan is configured for the port.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

hmAgentDot1xMaxUsers 1.3.6.1.4.1.248.15.36.2.1.1.5
Specifies the maximum users or clients that can authenticate on this port when the port control mode is macBased.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

hmAgentDot1xPortVlanAssigned 1.3.6.1.4.1.248.15.36.2.1.1.6
Specifies the vlan the port is assigned to by Dot1x . Only relevant if the port control mode of the port is auto.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hmAgentDot1xPortVlanAssignedReason 1.3.6.1.4.1.248.15.36.2.1.1.7
Reason the port is assigned to the vlan specified by hmAgentDot1xPortVlanAssigned . Only relevant if the port control mode of the port is auto.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER default(1), radius(2), unauthenticatedVlan(3), guestVlan(4), voiceVlan(5), notAssigned(7)  

hmAgentDot1xPortSessionTimeout 1.3.6.1.4.1.248.15.36.2.1.1.8
Specifies the session timeout value assigned by the Radius server for this port . Only relevant if the port control mode of the port is auto.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hmAgentDot1xPortTerminationAction 1.3.6.1.4.1.248.15.36.2.1.1.9
Specifies the session termination action assigned by the Radius Server .This is the action taken when the session times out . Only relevant if the port control mode of the port is auto.
Status: current Access: read-only
OBJECT-TYPE    
  HmAgentDot1xSessionTerminationAction  

hmAgentDot1xPortMABenabled 1.3.6.1.4.1.248.15.36.2.1.1.10
Specifies if Mac-based bypass authentication is configured for the port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentDot1xPortMABenabledOperational 1.3.6.1.4.1.248.15.36.2.1.1.11
Displays the operational value of the Mac-based authentication bypass mode (MAB) on the port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hmAgentDot1xClientConfigGroup 1.3.6.1.4.1.248.15.36.3
OBJECT IDENTIFIER    

hmAgentDot1xClientConfigTable 1.3.6.1.4.1.248.15.36.3.1
A table for dot1x Client details and associated functionality.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HmAgentDot1xClientConfigEntry

hmAgentDot1xClientConfigEntry 1.3.6.1.4.1.248.15.36.3.1.1
Represents entry for port config table.
Status: current Access: not-accessible
OBJECT-TYPE    
  HmAgentDot1xClientConfigEntry  

hmAgentDot1xClientMacAddress 1.3.6.1.4.1.248.15.36.3.1.1.1
Specifies the client MAC address of the client.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

hmAgentDot1xLogicalPort 1.3.6.1.4.1.248.15.36.3.1.1.2
Specifies the client MAC address of the client .
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hmAgentDot1xInterface 1.3.6.1.4.1.248.15.36.3.1.1.3
Specifies the physical interface to which the client is attached .
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hmAgentDot1xClientAuthPAEstate 1.3.6.1.4.1.248.15.36.3.1.1.4
The current value of the Authenticator PAE state machine for the client.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER initialize(1), disconnected(2), connecting(3), authenticating(4), authenticated(5), aborting(6), held(7), forceAuth(8), forceUnauth(9)  

hmAgentDot1xClientBackendState 1.3.6.1.4.1.248.15.36.3.1.1.5
The current state of the Backend Authentication state machine.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER request(1), response(2), success(3), fail(4), timeout(5), idle(6), initialize(7)  

hmAgentDot1xClientUserName 1.3.6.1.4.1.248.15.36.3.1.1.6
Specifies the username with which the client is authenticated to the Radius server . This value is only valid when the client is in authenticated state.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

hmAgentDot1xClientSessionTime 1.3.6.1.4.1.248.15.36.3.1.1.7
Specifies the time elapsed in seconds since the client was authenticated in this session. This value is only valid when the client is in authenticated state.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hmAgentDot1xClientFilterID 1.3.6.1.4.1.248.15.36.3.1.1.8
Specifies the Filter ID or Diffserv Policy name to be applied to the session . This vlaue is populated only if it has been assigned by the RADIUS server. This value is only valid when the client is in authenticated state.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

hmAgentDot1xClientVlanAssigned 1.3.6.1.4.1.248.15.36.3.1.1.9
Specifies the vlan the client is associated with by Dot1x . This value is only valid when the client is in authenticated state.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hmAgentDot1xClientVlanAssignedReason 1.3.6.1.4.1.248.15.36.3.1.1.10
Reason the client is associated to the vlan specified by hmAgentDot1xClientVlanAssigned . This value is only valid when the client is in authenticated state.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER default(1), radius(2), unauthenticatedVlan(3), guestVlan(4), voiceVlan(5), invalid(7)  

hmAgentDot1xClientSessionTimeout 1.3.6.1.4.1.248.15.36.3.1.1.11
Specifies the session time remaining for the client if assigned by the Radius server . A value of 0 indicates that no session timeout was assigned by the RADIUS server. This value is only valid when the client is in authenticated state.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hmAgentDot1xClientTerminationAction 1.3.6.1.4.1.248.15.36.3.1.1.12
Specifies the session termination action assigned by the Radius Server . This is the action taken when the session times out . This value is only valid when the client is in authenticated state.
Status: current Access: read-only
OBJECT-TYPE    
  HmAgentDot1xSessionTerminationAction  

hmPlatform4SwitchingTraps 1.3.6.1.4.1.248.15.1.50
OBJECT IDENTIFIER    

multipleUsersTrap 1.3.6.1.4.1.248.15.1.50.1
This trap is sent when more than one user is logged in with administrative access. Only applies to CLI interface.
Status: current Access: read-only
NOTIFICATION-TYPE    

broadcastStormStartTrap 1.3.6.1.4.1.248.15.1.50.2
Trap is obsolete.
Status: obsolete Access: read-only
NOTIFICATION-TYPE    

broadcastStormEndTrap 1.3.6.1.4.1.248.15.1.50.3
Trap is obsolete.
Status: obsolete Access: read-only
NOTIFICATION-TYPE    

linkFailureTrap 1.3.6.1.4.1.248.15.1.50.4
Trap is obsolete.
Status: obsolete Access: read-only
NOTIFICATION-TYPE    

vlanRequestFailureTrap 1.3.6.1.4.1.248.15.1.50.5
Trap is obsolete.
Status: obsolete Access: read-only
NOTIFICATION-TYPE    

vlanDeleteLastTrap 1.3.6.1.4.1.248.15.1.50.6
Trap is sent when attempting to delete the last configured VLAN or the Default VLAN.
Status: current Access: read-only
NOTIFICATION-TYPE    

vlanDefaultCfgFailureTrap 1.3.6.1.4.1.248.15.1.50.7
Trap is sent if there are failures in resetting VLAN configuration to defaults.
Status: current Access: read-only
NOTIFICATION-TYPE    

vlanRestoreFailureTrap 1.3.6.1.4.1.248.15.1.50.8
Trap is obsolete.
Status: obsolete Access: read-only
NOTIFICATION-TYPE    

fanFailureTrap 1.3.6.1.4.1.248.15.1.50.9
Trap is obsolete.
Status: obsolete Access: read-only
NOTIFICATION-TYPE    

stpInstanceNewRootTrap 1.3.6.1.4.1.248.15.1.50.10
Trap is sent when this machine is a new STP Root when there is more than one STP instance.
Status: current Access: read-only
NOTIFICATION-TYPE    

stpInstanceTopologyChangeTrap 1.3.6.1.4.1.248.15.1.50.11
Trap is sent when there is a STP topology change when there is more than one STP instance.
Status: current Access: read-only
NOTIFICATION-TYPE    

powerSupplyStatusChangeTrap 1.3.6.1.4.1.248.15.1.50.12
Trap is obsolete.
Status: obsolete Access: read-only
NOTIFICATION-TYPE    

failedUserLoginTrap 1.3.6.1.4.1.248.15.1.50.13
Trap is sent when a user fails to authenticate via the CLI or Web interfaces.
Status: current Access: read-only
NOTIFICATION-TYPE    

dot1xTraps 1.3.6.1.4.1.248.15.36.4
OBJECT IDENTIFIER    

dot1xPortStatusAuthorized 1.3.6.1.4.1.248.15.36.4.1
DOT1X port status is authorized.
Status: current Access: read-only
NOTIFICATION-TYPE    

dot1xPortStatusUnauthorized 1.3.6.1.4.1.248.15.36.4.2
DOT1X port status is unauthorized.
Status: current Access: read-only
NOTIFICATION-TYPE