| Hh3cPsePortEntry |
|
| SEQUENCE |
|
|
|
| |
hh3cPsePortFaultDescription |
DisplayString |
|
| |
hh3cPsePortPeakPower |
Integer32 |
|
| |
hh3cPsePortAveragePower |
Integer32 |
|
| |
hh3cPsePortCurrentPower |
Integer32 |
|
| |
hh3cPsePortPowerLimit |
Integer32 |
|
| |
hh3cPsePortProfileIndex |
Integer32 |
|
| Hh3cMainPseEntry |
|
| SEQUENCE |
|
|
|
| |
hh3cMainGuaranteedPowerRemaining |
Integer32 |
|
| |
hh3cMainPsePeakPower |
Integer32 |
|
| |
hh3cMainPseAveragePower |
Integer32 |
|
| |
hh3cMainPsePowerLimit |
Integer32 |
|
| |
hh3cMainPsePriorityMode |
INTEGER |
|
| |
hh3cMainPseLegacy |
INTEGER |
|
| |
hh3cMainPsePowerPriority |
INTEGER |
|
| Hh3cPOEACSwitchStateEntry |
|
| SEQUENCE |
|
|
|
| |
hh3cPOEACSwitchStateIndex |
Integer32 |
|
| |
hh3cPOEACSwitchState |
SwitchState |
|
| Hh3cPOESwitchStateVolExEntry |
|
| SEQUENCE |
|
|
|
| |
hh3cPOESwitchStateVolExIndex |
Integer32 |
|
| |
hh3cPOESwitchStateInVolAB |
ACAlarmState |
|
| |
hh3cPOESwitchStateInVolBC |
ACAlarmState |
|
| |
hh3cPOESwitchStateInVolCA |
ACAlarmState |
|
| Hh3cPOEAlarmStateInfoEntry |
|
| SEQUENCE |
|
|
|
| |
hh3cPOEAlarmModuleInfoIndex |
Integer32 |
|
| |
hh3cPOEModuleDisconnect |
ModuleAlarmState |
|
| |
hh3cPOEModuleInputError |
ModuleAlarmState |
|
| |
hh3cPOEModuleOutputError |
ModuleAlarmState |
|
| |
hh3cPOEModuleOverVoltage |
ModuleAlarmState |
|
| |
hh3cPOEModuleOverTemp |
ModuleAlarmState |
|
| |
hh3cPOEModuleFanError |
ModuleAlarmState |
|
| |
hh3cPOEModuleShutdown |
ModuleAlarmState |
|
| |
hh3cPOEModuleCurRestricted |
ModuleAlarmState |
|
| hh3cPsePortEntry |
1.3.6.1.4.1.25506.2.14.1.1 |
| The pethPsePortGroupIndex is imported from the IETF Power MIB
and uniquely identifies the group containing the port to which
power ethernet PSE is connected. Group means (box in the stack,
module in a rack).
The pethPsePortPowerIndex is imported from the IETF Power MIB
and uniquely identifies the power ethernet PSE port within group
pethPseGroupIndex to which the power Ethernet PSE entry is
connected. This value will match the local port number on a
switch. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
Hh3cPsePortEntry |
|
|
| hh3cMainPseEntry |
1.3.6.1.4.1.25506.2.14.2.1 |
| The pethMainPseGroupIndex is imported from the IETF Power MIB
and uniquely identifies the group containing the port to which
power ethernet PSE is connected. Group means (box in the stack,
module in a rack) and the value 1 MUST be used for non-modular
devices. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
Hh3cMainPseEntry |
|
|
| hh3cMainPsePowerLimit |
1.3.6.1.4.1.25506.2.14.2.1.1 |
| The object specifies the power limit set for the unit as a whole.
The PoE unit will already have a nominal power defined by the
IETF Power MIB [1] pethMainPsePower object. This OPTIONAL object
specifies a further limit to this nominal power value. This may
be useful to control the thermals of the unit, or for internal
testing purposes. One possible use for this object may be to lower
the power consumption of the unit if one or more of the internal
fans have broken. It is a read/write integer value with units of
Watts (note - Watts is chosen instead of milliWatts here since
the IETF Power MIB [1] measures unit based parameters, such as
the pethMainPsePower object, in units of Watts). |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| hh3cMainPseAveragePower |
1.3.6.1.4.1.25506.2.14.2.1.2 |
| The object specifies the average power which has been consumed
by the port. It is a read/write integer value with units of
Watts (note - Watts is chosen instead of milliWatts here since
the IETF Power MIB [1] measures unit based parameters, such as
the pethMainPsePower object, in units of Watts). Writing a value
of zero to this object resets its value to zero. Writing any
other value to this object has no effect on its value and an error
is returned. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| hh3cMainPsePeakPower |
1.3.6.1.4.1.25506.2.14.2.1.3 |
| The object specifies the peak power which has been consumed for PoE.
It is defined as the highest measured value of power in milliWatts
that has been consumed at any one point in time by the sum of the PoE
ports. Its value is only reset when the unit is powered on or when
it is manually reset by the user as specifiedbelow. It is a read/write
integer value with units of Watts (note - Watts is chosen instead of
milliWatts here since the IETF Power MIB [1] measures unit based
parameters, such as the pethMainPsePower object, in units of Watts).
Writing a value of zero to this object resets its value to zero.
Writing any other value to this object has noeffect on its value
and an error is returned. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| hh3cMainGuaranteedPowerRemaining |
1.3.6.1.4.1.25506.2.14.2.1.4 |
| The object specifies the amount of power remaining in the guaranteed
power pool. Each time a port is placed into guaranteed mode it
reserves a set amount of power out of the total guaranteed power
pool for the system. This intention of this object is to give the
client of this MIB (whether that be the CLI or the Web interface or
the end user) an indication of how many ports can still be placed
into guaranteed mode. It is a read only integer value with units of
Watts(note - Watts is chosen instead of milliWatts here since the
IETF Power MIB [1] measures unit based parameters,such as the
pethMainPsePower object, in units of Watts). |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| hh3cMainPsePriorityMode |
1.3.6.1.4.1.25506.2.14.2.1.5 |
| Describes or controls the priority mode on slot which must be
enabled firstly. When a new board is inserted, and the power is
over-load, a value of disconnection(0) means that the power will
stop supply to the low priority slot ; A value of non-disconnection(1)
means that the slot still supply when a new board is inserted, and
the power is over-load too. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
disconnection(0), non-disconnection(1) |
|
| hh3cMainPseLegacy |
1.3.6.1.4.1.25506.2.14.2.1.6 |
| Describes or controls the legacy mode on slot which must be enabled
firstly. Legacy mode: standard or nonstandard PD detection mode. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enable(0), disable(1) |
|
| hh3cMainPsePowerPriority |
1.3.6.1.4.1.25506.2.14.2.1.7 |
| Describes or controls the priority of the PSE. The priority
will be used by the PSE policy to prevent from power overloading.
If the priority of PSE is set to critical, the PSE will turn into
guaranteed mode. The priority could be used by a control mechanism
that prevents power overloading by disconnecting PSEs with lower
power priority. PSEs that connect devices critical to the
application should be set to higher priority. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
critical(1), high(2), low(3) |
|
| hh3cPseProfilesEntry |
1.3.6.1.4.1.25506.2.14.7.1 |
| A set of objects that display and control the Main power of a PSE. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
Hh3cPseProfilesEntry |
|
|
| hh3cMainPseGroup |
1.3.6.1.4.1.25506.2.14.4.2.2 |
| A collection of objects should be supported at the same time. |
| Status: current |
Access: read-write |
| OBJECT-GROUP |
|
|
|
| hh3cPOEModuleInfoEntry |
1.3.6.1.4.1.25506.2.14.8.2.7.1 |
| The entry of the module information on this POE power. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
Hh3cPOEModuleInfoEntry |
|
|
| hh3cPOEDCOutStateEntry |
1.3.6.1.4.1.25506.2.14.8.3.2.1 |
| The entry of the DC output power state on this POE power. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
Hh3cPOEDCOutStateEntry |
|
|
| hh3cPOEDCOutInfoEntry |
1.3.6.1.4.1.25506.2.14.8.4.2.1 |
| The entry of the DC output information on this POE power. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
Hh3cPOEDCOutInfoEntry |
|
|
| hh3cPOEACSwitchStateEntry |
1.3.6.1.4.1.25506.2.14.8.5.2.1 |
| The entry of the AC switch state on this POE power. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
Hh3cPOEACSwitchStateEntry |
|
|
| hh3cPOESwitchStateVolExEntry |
1.3.6.1.4.1.25506.2.14.8.6.5.1 |
| The hh3cPOESwitchStateVolExIndex will match the number of the VOL status. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
Hh3cPOESwitchStateVolExEntry |
|
|
| hh3cPOEAlarmStateInfoEntry |
1.3.6.1.4.1.25506.2.14.8.7.2.1 |
| The hh3cPOEAlarmModuleInfoIndex will match the number
of the power module. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
Hh3cPOEAlarmStateInfoEntry |
|
|
