HDR2-MIB

File: HDR2-MIB.mib (22749 bytes)

Imported modules

RFC1155-SMI

RFC1213-MIB

RFC-1212

Imported symbols

enterprises

DisplayString

OBJECT-TYPE

Defined Types

Hdr2CfgEntry
SEQUENCE
	hdr2CfgIndex	INTEGER
	hdr2CfgRegSigType	INTEGER
	hdr2CfgAnumIden	INTEGER
	hdr2CfgForcedRel	INTEGER
	hdr2CfgLastBDigTout	INTEGER
	hdr2CfgAddrComplete	INTEGER
	hdr2CfgEndBparty	INTEGER
	hdr2CfgAlawMulaw	INTEGER
	hdr2CfgLineSigType	INTEGER
	hdr2CfgProjID	INTEGER
	hdr2CfgSeizeAck	INTEGER
	hdr2CfgAnumBnum	INTEGER
	hdr2CfgSubBusy	INTEGER
	hdr2CfgSndCallingPtyCatgy	INTEGER
	hdr2CfgLineDirection	INTEGER
	hdr2CfgPersistentOverride	INTEGER
	hdr2CfgWrongNumber	INTEGER
	hdr2CfgIncomingCpc	INTEGER
	hdr2CfgRegSigStatus	INTEGER
	hdr2CfgUnusedAbcd	INTEGER
	hdr2CfgBlkToBlk	INTEGER
	hdr2CfgDelayLos	INTEGER
	hdr2CfgInGlare	INTEGER
	hdr2CfgClrCall	INTEGER
	hdr2CfgANumQry	INTEGER
	hdr2CfgANumNAv	INTEGER
	hdr2CfgANumReq	INTEGER
	hdr2CfgClrFwd	INTEGER
	hdr2CfgRelGuard	INTEGER
	hdr2CfgPIClrBck	INTEGER
	hdr2CfgDelayAns	INTEGER
	hdr2CfgBNumLen	INTEGER
	hdr2CfgActBTout	INTEGER
	hdr2CfgInSubFree	INTEGER
	hdr2CfgBNumNFnd	INTEGER
	hdr2CfgSndBNumN	INTEGER
	hdr2CfgSndBNumN1	INTEGER
	hdr2CfgSndBNumN2	INTEGER
	hdr2CfgSndBNumN3	INTEGER
	hdr2CfgSndFBNum	INTEGER
	hdr2CfgDumANum	DisplayString
	hdr2CfgEndANum	INTEGER
	hdr2CfgOutCatAnalog	INTEGER
	hdr2CfgOutCatDigital	INTEGER
	hdr2CfgOutCatTest	INTEGER
	hdr2CfgOutCatMaintenance	INTEGER

Hdr2InCatMapEntry
SEQUENCE
	hdr2InCatMapIndex	INTEGER
	hdr2InCatMapSigNum	INTEGER
	hdr2InCatMapCallType	INTEGER

Hdr2PteEntry
SEQUENCE
	hdr2PteIndex	INTEGER
	hdr2PteMultiFrame	INTEGER
	hdr2PteMultiFrameClr	INTEGER
	hdr2PteRemMultiFrame	INTEGER
	hdr2PteRemMultiFrameClr	INTEGER

Hdr2TeEntry
SEQUENCE
	hdr2TeIndex	INTEGER
	hdr2TeMultiFrame	INTEGER
	hdr2TeMultiFrameClr	INTEGER
	hdr2TeRemMultiFrame	INTEGER
	hdr2TeRemMultiFrameClr	INTEGER

Defined Values

usr		1.3.6.1.4.1.429
OBJECT IDENTIFIER

common		1.3.6.1.4.1.429.4
OBJECT IDENTIFIER

hdr2		1.3.6.1.4.1.429.4.48
OBJECT IDENTIFIER

hdr2Cfg		1.3.6.1.4.1.429.4.48.1
OBJECT IDENTIFIER

hdr2CfgTable		1.3.6.1.4.1.429.4.48.1.1
A table containing the configuration parameters for the Hiper E1/R2 Card.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hdr2CfgEntry

hdr2CfgEntry		1.3.6.1.4.1.429.4.48.1.1.1
Configuration parameters for the E1/R2 module.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	Hdr2CfgEntry

hdr2CfgIndex		1.3.6.1.4.1.429.4.48.1.1.1.1
The index which uniquely identifies the Hiper E1/R2 CARD to which this entry is applicable.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

hdr2CfgRegSigType		1.3.6.1.4.1.429.4.48.1.1.1.2
This object Defines the type of Register Signaling used for Bit Oriented Signaling.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	r2MFC(1), r2MFSC(2)

hdr2CfgAnumIden		1.3.6.1.4.1.429.4.48.1.1.1.3
This parameter enables or disables the collection of calling party ( A party or ANI) phone numbers when used with R2MFC signaling type.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

hdr2CfgForcedRel		1.3.6.1.4.1.429.4.48.1.1.1.4
In E1/ R2 ,Forced Release Line signal will be sent only in case of this parameter is enabled. This signal is optional.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

hdr2CfgLastBDigTout		1.3.6.1.4.1.429.4.48.1.1.1.5
This parameter decides, after how many milliseconds of silence during the B digit reception, the B party number is assumed as completed.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	100..10000

hdr2CfgAddrComplete		1.3.6.1.4.1.429.4.48.1.1.1.6
On reception of this signal it is assumed that the required number of B party digits are received. It can hold the values ranging from A1 to A15. It depends on country specification.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	a3(1), a5(2), a6(3)

hdr2CfgEndBparty		1.3.6.1.4.1.429.4.48.1.1.1.7
This indicates whether I15 is will be received as an indication for End of B party number or not. If enabled, at the end of B party number , this I15 signal is received informing that B party number is completed.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

hdr2CfgAlawMulaw		1.3.6.1.4.1.429.4.48.1.1.1.8
This object is configuration to apply A Law(E1) or MuLaw(T1) Companding.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	aLAW(1), mULAW(2), auto(3)

hdr2CfgLineSigType		1.3.6.1.4.1.429.4.48.1.1.1.9
This object defines the type of Line Signaling for Bit Oriented Signaling.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	r2DIG(1), p7DIG(2), r2EandM(3)

hdr2CfgProjID		1.3.6.1.4.1.429.4.48.1.1.1.10
Depending on this parameter, country dependent or project dependent parameters are updated. Each and every parameter has a set of variables to be initialized.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	iTU-T(1), argentina(2), australia(3), brazil(4), chile(5), china(6), colombia(7), india(8), korea(9), malaysia(10), mexico(11), newZealand(12), philippines(13), sweden(14), venezuela(15)

hdr2CfgSeizeAck		1.3.6.1.4.1.429.4.48.1.1.1.11
It defines whether seize acknowledge signal is used or not for Bit Oriented Signaling.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

hdr2CfgAnumBnum		1.3.6.1.4.1.429.4.48.1.1.1.12
During Bit oriented Register Signaling , after number of B party ( called party or DNIS) digits have been received, the A party (calling or ANI) digits are requested , provided A party (ANI) request is enabled. Otherwise this parameter is ignored.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..36

hdr2CfgSubBusy		1.3.6.1.4.1.429.4.48.1.1.1.13
This object is used in case of subscirber busy.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	b2(1), b3(2)

hdr2CfgSndCallingPtyCatgy		1.3.6.1.4.1.429.4.48.1.1.1.14
This register Signal requests the calling ( A PARTY's ) category.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	a5(1), a6(2)

hdr2CfgLineDirection		1.3.6.1.4.1.429.4.48.1.1.1.15
This object sets the direction of the channels on the span line.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	incoming(1), outgoing(2), both(3)

hdr2CfgPersistentOverride		1.3.6.1.4.1.429.4.48.1.1.1.16
This object allows the recieved line signal persistence (debounce time).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

hdr2CfgWrongNumber		1.3.6.1.4.1.429.4.48.1.1.1.17
This object is the backward register signal used to indicate that an invalid number has been dialed.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	b5(1), b7(2)

hdr2CfgIncomingCpc		1.3.6.1.4.1.429.4.48.1.1.1.18
This object determines the default calling party category to be assumed when none is supplied for an incoming call.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	analog(1), digital(2), maintanace(3), test(4)

hdr2CfgRegSigStatus		1.3.6.1.4.1.429.4.48.1.1.1.19
This object determines whether or not register signalling is used for incoming and outgoing calls for R2.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

hdr2CfgUnusedAbcd		1.3.6.1.4.1.429.4.48.1.1.1.20
This object determines the bit pattern transmitted for whichever of the ABCD bits are not used for the selected line signalling scheme. This means CD for R2 Digital and P7, and BCD for R2 E&M.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..15

hdr2CfgBlkToBlk		1.3.6.1.4.1.429.4.48.1.1.1.21
This object determines whether or not a blocking signals received in the idle state is automatically responded to with a transmitted block signals.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

hdr2CfgDelayLos		1.3.6.1.4.1.429.4.48.1.1.1.22
This object determines the required duration of the LOS state before active calls are dropped and the signalling is reinitialised. Restoration of signal during this period allows calls to continue.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..10000

hdr2CfgInGlare		1.3.6.1.4.1.429.4.48.1.1.1.23
This object determines whether the incoming call is accepted and the outgoing call is dropped in a glare condition, or both calls are dropped as currently implemented.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

hdr2CfgClrCall		1.3.6.1.4.1.429.4.48.1.1.1.24
This object determines whether an active call is cleared when an unexpected line signal is received, or the line signal is ignored as currently implemented.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

hdr2CfgANumQry		1.3.6.1.4.1.429.4.48.1.1.1.25
This object determines whether or not an extra MFC cycle is used before to the A-number to indicate whether an A-number is available,using III-1 for yes and III-0 for no.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

hdr2CfgANumNAv		1.3.6.1.4.1.429.4.48.1.1.1.26
THis object interpret I-12 as A-number not available.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

hdr2CfgANumReq		1.3.6.1.4.1.429.4.48.1.1.1.27
this object backward register signal used to request transmission of the next A-number digit Frequently this is the same as the signal used to request transmission of the call category and A-number .
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	c1(1), c5(2), c6(3), c9(4)

hdr2CfgClrFwd		1.3.6.1.4.1.429.4.48.1.1.1.28
This object repeatd size/clear-forward sequence is sent to startup to try to provoke a response from attached equipment.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

hdr2CfgRelGuard		1.3.6.1.4.1.429.4.48.1.1.1.29
This object is duration for which Release Guard signal is sent.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..2000

hdr2CfgPIClrBck		1.3.6.1.4.1.429.4.48.1.1.1.30
This object determines whether or not a repeated release/Seize-ack sequence is sent while attempting to clear anincoming call.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

hdr2CfgDelayAns		1.3.6.1.4.1.429.4.48.1.1.1.31
this object determines the delay between the end of addressing and transmission of the answer signal.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	100..2000

hdr2CfgBNumLen		1.3.6.1.4.1.429.4.48.1.1.1.32
this object determines the number of B-number digits to accept beore sending the 'address complete'signal, provided the 'end of B_number'signal is not received first.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..36

hdr2CfgActBTout		1.3.6.1.4.1.429.4.48.1.1.1.33
this object determines action to be taken on last B-digit timeout.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	b-number(1), error(2)

hdr2CfgInSubFree		1.3.6.1.4.1.429.4.48.1.1.1.34
this object backward register signal used to indicate acceptance of an incoming call.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	b1(1), b5(2), b6(3)

hdr2CfgBNumNFnd		1.3.6.1.4.1.429.4.48.1.1.1.35
this object determines the action on B-Number not found in teh DNIS handling table.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	acceptAllCalls(1), rejectAllCalls(2), acceptAllCallsAsDigital(3), acceptAllCallsAnalog(4)

hdr2CfgSndBNumN		1.3.6.1.4.1.429.4.48.1.1.1.36
this object backward signal requesting retransmission of curent B-number digit for outgoing calls.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	a9(1), a10(2)

hdr2CfgSndBNumN1		1.3.6.1.4.1.429.4.48.1.1.1.37
this object backward signal requesting transmission of B-number digit N-1 for outgoing calls.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	a2(1), a8(2), a9(3), a10(4)

hdr2CfgSndBNumN2		1.3.6.1.4.1.429.4.48.1.1.1.38
this object backward signal requesting transimission of B-number digit N-2 for outgoing calls.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	a7(1), a9(2)

hdr2CfgSndBNumN3		1.3.6.1.4.1.429.4.48.1.1.1.39
this object backward signal requesting transimission of B-number digit N-3 for outgoing calls.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	a8(1), a10(2)

hdr2CfgSndFBNum		1.3.6.1.4.1.429.4.48.1.1.1.40
this object determines whether or not the I-15 'end of B-number' signal is used for outgoing calls.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	a2(1), a9(2), a10(3)

hdr2CfgDumANum		1.3.6.1.4.1.429.4.48.1.1.1.41
this object default A-number for outgoing calls in case none is supplied during call initiation.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(1..36)

hdr2CfgEndANum		1.3.6.1.4.1.429.4.48.1.1.1.42
This object forward register signal used to indicate that no more a_number digits are avaible.default=iii-15.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	iii-12(1), iii-15(2)

hdr2CfgOutCatAnalog		1.3.6.1.4.1.429.4.48.1.1.1.43
This object forward signals used to indicate the call category for outgoing calls.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ii-1(1), ii-2(2), ii-3(3), ii-4(4), ii-5(5), ii-6(6), ii-7(7), ii-8(8), ii-9(9), ii-10(10), ii-11(11), ii-12(12), ii-13(13), ii-14(14), ii-15(15)

hdr2CfgOutCatDigital		1.3.6.1.4.1.429.4.48.1.1.1.44
Tok_String
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ii-1(1), ii-2(2), ii-3(3), ii-4(4), ii-5(5), ii-6(6), ii-7(7), ii-8(8), ii-9(9), ii-10(10), ii-11(11), ii-12(12), ii-13(13), ii-14(14), ii-15(15)

hdr2CfgOutCatTest		1.3.6.1.4.1.429.4.48.1.1.1.45
Tok_String
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ii-1(1), ii-2(2), ii-3(3), ii-4(4), ii-5(5), ii-6(6), ii-7(7), ii-8(8), ii-9(9), ii-10(10), ii-11(11), ii-12(12), ii-13(13), ii-14(14), ii-15(15)

hdr2CfgOutCatMaintenance		1.3.6.1.4.1.429.4.48.1.1.1.46
Tok_String
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ii-1(1), ii-2(2), ii-3(3), ii-4(4), ii-5(5), ii-6(6), ii-7(7), ii-8(8), ii-9(9), ii-10(10), ii-11(11), ii-12(12), ii-13(13), ii-14(14), ii-15(15)

hdr2InCatMap		1.3.6.1.4.1.429.4.48.2
OBJECT IDENTIFIER

hdr2InCatMapTable		1.3.6.1.4.1.429.4.48.2.1
A table containing in cat map configurations for the Hiper E1/R2 Module.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hdr2InCatMapEntry

hdr2InCatMapEntry		1.3.6.1.4.1.429.4.48.2.1.1
Configuration parameters for the E1/R2 module.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	Hdr2InCatMapEntry

hdr2InCatMapIndex		1.3.6.1.4.1.429.4.48.2.1.1.1
The index which uniquely identifies the Hiper E1/R2 Module to which this entry is applicable.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

hdr2InCatMapSigNum		1.3.6.1.4.1.429.4.48.2.1.1.2
This object is the index for one of 15 possible forward call category signals for imcoming calls.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..15

hdr2InCatMapCallType		1.3.6.1.4.1.429.4.48.2.1.1.3
This object determines the meaning of forward call category for incoming calls.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	analog(1), digital(2), test(3), maintenance(4)

hdr2Pte		1.3.6.1.4.1.429.4.48.3
OBJECT IDENTIFIER

hdr2PteTable		1.3.6.1.4.1.429.4.48.3.1
A table containing the Positron Trap Enable configurations for the Hiper E1/R2 Module.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hdr2PteEntry

hdr2PteEntry		1.3.6.1.4.1.429.4.48.3.1.1
Trap Enable Configuration parameters for the E1/R2 module.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	Hdr2PteEntry

hdr2PteIndex		1.3.6.1.4.1.429.4.48.3.1.1.1
The index which uniquely identifies the Hiper E1/R2 Module to which this entry is applicable.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

hdr2PteMultiFrame		1.3.6.1.4.1.429.4.48.3.1.1.2
Enable the generation of an SNMP trap upon detection of a Multi-Frame Alignment condition on the specified DS1.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disableAll(1), enableTrapOnly(2), enableSysLogOnly(3), enableAll(4)

hdr2PteMultiFrameClr		1.3.6.1.4.1.429.4.48.3.1.1.3
Enable the generation of an SNMP trap upon detection of clearing a Multi-Frame Alignment condition on the specified DS1.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disableAll(1), enableTrapOnly(2), enableSysLogOnly(3), enableAll(4)

hdr2PteRemMultiFrame		1.3.6.1.4.1.429.4.48.3.1.1.4
Enable the generation of an SNMP trap upon detection of a Remote Multi-Frame Alignment condition on the specified DS1.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disableAll(1), enableTrapOnly(2), enableSysLogOnly(3), enableAll(4)

hdr2PteRemMultiFrameClr		1.3.6.1.4.1.429.4.48.3.1.1.5
Enable the generation of an SNMP trap upon detection of clearing a Remote Multi-Frame Alignment condition on the specified DS1.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disableAll(1), enableTrapOnly(2), enableSysLogOnly(3), enableAll(4)

hdr2Te		1.3.6.1.4.1.429.4.48.4
OBJECT IDENTIFIER

hdr2TeTable		1.3.6.1.4.1.429.4.48.4.1
A table containing the Trap Enable configurations for the Hiper E1/R2 Module.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hdr2TeEntry

hdr2TeEntry		1.3.6.1.4.1.429.4.48.4.1.1
Trap Enable Configuration parameters for the E1/R2 module.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	Hdr2TeEntry

hdr2TeIndex		1.3.6.1.4.1.429.4.48.4.1.1.1
The index which uniquely identifies the Hiper E1/R2 CARD to which this entry is applicable.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

hdr2TeMultiFrame		1.3.6.1.4.1.429.4.48.4.1.1.2
Enable the generation of an SNMP trap upon detection of a Multi-Frame Alignment condition on the specified DS1.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enableTrap(1), disableAll(2), enableLog(3), enableAll(4)

hdr2TeMultiFrameClr		1.3.6.1.4.1.429.4.48.4.1.1.3
Enable the generation of an SNMP trap upon detection of clearing a Multi-Frame Alignment condition on the specified DS1.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enableTrap(1), disableAll(2), enableLog(3), enableAll(4)

hdr2TeRemMultiFrame		1.3.6.1.4.1.429.4.48.4.1.1.4
Enable the generation of an SNMP trap upon detection of a Remote Multi-Frame Alignment condition on the specified DS1.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enableTrap(1), disableAll(2), enableLog(3), enableAll(4)

hdr2TeRemMultiFrameClr		1.3.6.1.4.1.429.4.48.4.1.1.5
Enable the generation of an SNMP trap upon detection of clearing a Remote Multi-Frame Alignment condition on the specified DS1.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enableTrap(1), disableAll(2), enableLog(3), enableAll(4)