GDCMDM-MIB

File: GDCMDM-MIB.mib (80532 bytes)

Imported modules

RFC1155-SMI RFC1213-MIB RFC-1212
RFC-1215 GDCMACRO-MIB

Imported symbols

enterprises TimeTicks DisplayString
OBJECT-TYPE TRAP-TYPE SCinstance

Defined Types

MdmNetworkEntry  
SEQUENCE    
  mdmNetworkIndex SCinstance
  mdmNetworkType INTEGER
  mdmSNTxType INTEGER
  mdmSNTxLevel INTEGER
  mdmSNHandshakeMode INTEGER

MdmDTEntry  
SEQUENCE    
  mdmDTEIndex SCinstance
  mdmDTESpeed INTEGER
  mdmCPMResp INTEGER
  mdmCharLength INTEGER
  mdmParity INTEGER
  mdmOverspeed INTEGER
  mdmFlowCntrl INTEGER
  mdmTermEcho INTEGER
  mdmDCDCntrl INTEGER
  mdmCTSCntrl INTEGER
  mdmDTRTrans INTEGER
  mdmDSRCntrl INTEGER
  mdmDSRCntrlAL INTEGER
  mdmTXClockSource INTEGER
  mdmRTSCTSDelay INTEGER
  mdmCarriageReturnCharacter INTEGER
  mdmCharacterAbortDialing INTEGER
  mdmDelayDTR INTEGER
  mdmEscapeCharacter INTEGER
  mdmLineFeedCharacter INTEGER
  mdmHangUpDelay INTEGER
  mdmEscapeCharacterGuardTime INTEGER
  mdmOperatingMode INTEGER
  mdmBackSpaceCharacter INTEGER

MdmModemEntry  
SEQUENCE    
  mdmModemIndex SCinstance
  mdmRingsToAns INTEGER
  mdmFallFwrdBack INTEGER
  mdmTrellis INTEGER
  mdmSQRetrain INTEGER
  mdmLongSpaceDisc INTEGER
  mdmMakeBusy INTEGER
  mdmRDLOptions INTEGER
  mdmTestTimer INTEGER
  mdmDTETestCntrl INTEGER
  mdmDCDLossDisc INTEGER
  mdmCDRespTime INTEGER
  mdmAnswerOriginate INTEGER
  mdmWaitForDCD INTEGER

MdmDialerEntry  
SEQUENCE    
  mdmDialerIndex SCinstance
  mdmCPMMonitor INTEGER
  mdmParserSelection INTEGER
  mdmDTRDial INTEGER
  mdmDialType INTEGER
  mdmResponseMode INTEGER
  mdmResponseType INTEGER
  mdmPauseTime INTEGER
  mdmWaitForDialtoneTime INTEGER

MdmProtocolEntry  
SEQUENCE    
  mdmProtocolIndex SCinstance
  mdmCompression INTEGER
  mdmAsyncProtocol INTEGER
  mdmFlowControl INTEGER
  mdmBreakHandling INTEGER
  mdmConnAndLinkMessages INTEGER
  mdmErrorCorrection INTEGER
  mdmV13Mode INTEGER
  mdmSyncProtocol INTEGER
  mdmFrameRetransLimit INTEGER

MdmPrivateLineEntry  
SEQUENCE    
  mdmPrivateLineIndex SCinstance
  mdmPrivateLineTxLevel INTEGER
  mdmPrivateLineHandshakeMode INTEGER
  mdmAutoDialRestoral INTEGER
  mdmPrivateLineDownTime INTEGER
  mdmDBUtoPLLookbackTime INTEGER

MdmAlarmScanEntry  
SEQUENCE    
  mdmAlarmScanIndex SCinstance
  mdmAlarmScan OCTET STRING
  mdmResetSelfPowerBit INTEGER

MdmMaskAlarmEntry  
SEQUENCE    
  mdmMaskAlarmIndex SCinstance
  mdmDTRLoss INTEGER
  mdmFallback INTEGER
  mdmRxdTran INTEGER
  mdmTxdTran INTEGER
  mdmDCDLoss INTEGER
  mdmRingNoAnswer INTEGER
  mdmRetrain INTEGER
  mdmCallLength INTEGER
  mdmCallFail INTEGER
  mdmConfigErr INTEGER
  mdmSignalQuality INTEGER
  mdmOnDBU INTEGER
  mdmRemoteConfigMask INTEGER
  mdmTestTimeout INTEGER

MdmThresholdsEntry  
SEQUENCE    
  mdmThresholdsIndex SCinstance
  mdmCallDuration TimeTicks
  mdmRetrainThreshold INTEGER

MdmStatusEntry  
SEQUENCE    
  mdmStatusIndex SCinstance
  mdmPLLookbackStatus INTEGER
  mdmAutoDialRestoralStatus INTEGER
  mdmTXDtransitions INTEGER
  mdmRXDtransitions INTEGER
  mdmRTStransitions INTEGER
  mdmDTRtransitions INTEGER
  mdmDCDtransitions INTEGER
  mdmTXCLKtransitions INTEGER
  mdmDTR INTEGER
  mdmCTS INTEGER
  mdmDSR INTEGER
  mdmDCD INTEGER
  mdmSQM INTEGER
  mdmRTS INTEGER
  mdmSwitchedPrivate INTEGER

MdmControlEntry  
SEQUENCE    
  mdmControlIndex SCinstance
  mdmSoftReset INTEGER
  mdmFrontPanel INTEGER
  mdmMakeClearBusy INTEGER
  mdmPLTalkData INTEGER

MdmWhatAreYouEntry  
SEQUENCE    
  mdmWhatAreYouIndex SCinstance
  mdmVFCard INTEGER
  mdmDTECard INTEGER
  mdmProductCode INTEGER
  mdmCodeRev DisplayString
  mdmBootRev DisplayString
  mdmCountryCode DisplayString

MdmDiagnosticEntry  
SEQUENCE    
  mdmDiagnosticIndex SCinstance
  mdmDiagnosticTest INTEGER
  mdmDiagnosticResults INTEGER
  mdmDiagnosticStatus INTEGER
  mdmTestStatus INTEGER
  mdmTestDuration TimeTicks

MdmDialingFunctionEntry  
SEQUENCE    
  mdmDialFunctionIndex SCinstance
  mdmManualDial DisplayString
  mdmTerminateCall INTEGER
  mdmDialStatus INTEGER
  mdmCallProgressStatus INTEGER

MdmDialingCellsFunctionEntry  
SEQUENCE    
  mdmDialCellFunctionIndex SCinstance
  mdmCellNumber INTEGER
  mdmDial INTEGER
  mdmCellPhoneNumber DisplayString
  mdmTerminateCellCall INTEGER

MdmMaintenanceEntry  
SEQUENCE    
  mdmMaintenanceIndex SCinstance
  mdmSaveRecallConfig INTEGER
  mdmConfigCksum OCTET STRING
  mdmPassword DisplayString
  mdmSerialNumber DisplayString
  mdmPowerUpProfile INTEGER
  mdmPasswordOperation INTEGER

MdmStatisticsEntry  
SEQUENCE    
  mdmStatisticsIndex SCinstance
  mdmDCERate INTEGER
  mdmCallDurationStat TimeTicks
  mdmRetrainCount INTEGER
  mdmFallbackCount INTEGER
  mdmFallforwardCount INTEGER
  mdmRxSignalLevel INTEGER
  mdmSignaltoNoiseRatio INTEGER
  mdmAnswerOriginateStat INTEGER
  mdmDiscReason INTEGER
  mdmCompressionEfficiency INTEGER
  mdmThruput INTEGER

MdmRemoteConfigEntry  
SEQUENCE    
  mdmRemoteConfigIndex SCinstance
  mdmRemoteConfiguration INTEGER
  mdmEndRemoteConfiguration INTEGER
  mdmPasswordRemoteConfiguration DisplayString

Defined Values

gdc 1.3.6.1.4.1.498
OBJECT IDENTIFIER    

mdm 1.3.6.1.4.1.498.4
OBJECT IDENTIFIER    

mdmNetworkConfigTable 1.3.6.1.4.1.498.4.1
The GDC VFAST modem network configuration table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MdmNetworkEntry

mdmNetworkEntry 1.3.6.1.4.1.498.4.1.1
A listing of GDC VFAST modem network options.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MdmNetworkEntry  

mdmNetworkIndex 1.3.6.1.4.1.498.4.1.1.1
A unique index for the Network Table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SCinstance  

mdmNetworkType 1.3.6.1.4.1.498.4.1.1.2
Command to option the VF line type mode of operation.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER switchedNetwork(1), privateLine2Wire(2), privateLine4Wire(3)  

mdmSNTxType 1.3.6.1.4.1.498.4.1.1.3
Command used to select either Permissive or Programable Switched Network Transmit Level. This object is Country Code dependent
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER permissive(1), programmable(2), adjustable(3)  

mdmSNTxLevel 1.3.6.1.4.1.498.4.1.1.4
Command to select(force) the Switched Network Transmit Level when modem is optioned for adjustable. This object is Country Code dependent
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..15  

mdmSNHandshakeMode 1.3.6.1.4.1.498.4.1.1.5
Available handshake modes. This object is Country Code dependent.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER gdcVfastAuto(1), gdcVfastOnly(2), v32bisAuto(3), v32bisOnly(4), v32Auto(5), v32Only(6), v22bis(7), v22Only(8), bell212(9), bell103(10), v21(11)  

mdmDTEConfigTable 1.3.6.1.4.1.498.4.2
The GDC VFAST modem Data Terminal Equipment configuration table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MdmDTEntry

mdmDTEntry 1.3.6.1.4.1.498.4.2.1
A listing of GDC VFAST modem DTE options.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MdmDTEntry  

mdmDTEIndex 1.3.6.1.4.1.498.4.2.1.1
A unique index for the DTE Table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SCinstance  

mdmDTESpeed 1.3.6.1.4.1.498.4.2.1.2
This option selects DTE bit Rate.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER autobaud(1), lastAT(2), bps300(3), bps1200(4), bps2400(5), bps4800(6), bps7200(7), bps9600(8), bps12000(9), bps14400(10), bps16800(11), bps19200(12), bps21600(13), bps24000(14), bps26400(15), bps28800(16), bps38400(17), bps57600(18), bps76800(19), bps115200(20), bps128000(21)  

mdmCPMResp 1.3.6.1.4.1.498.4.2.1.3
Selects the response rate of the Call Progress Monitor.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER autobaud(1), lastConnectSpeed(2), bps300(3), bps1200(4), bps2400(5), bps4800(6), bps7200(7), bps9600(8), bps12000(9), bps14400(10), bps16800(11), bps19200(12), bps21600(13), bps24000(14), bps26400(15), bps28800(16), bps38400(17), bps57600(18), bps76800(19), bps115200(20), bps128000(21)  

mdmCharLength 1.3.6.1.4.1.498.4.2.1.4
DTE charater length and format options of the DTE asynchronous data.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER data6Stop1(1), data7Stop1(2), data7ParityStop1(3), data8Stop1(4), data7ParityStop2(5), data8ParityStop1(6)  

mdmParity 1.3.6.1.4.1.498.4.2.1.5
Parity of the async data when the character length option selects parity.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER even(1), space(2), odd(3), mark(4), auto(5)  

mdmOverspeed 1.3.6.1.4.1.498.4.2.1.6
Option to set DTE async overspeed data tolerated by the modem. Extended = 2.5%. Nominal = 1.25%.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER nominal(1), extended(2)  

mdmFlowCntrl 1.3.6.1.4.1.498.4.2.1.7
Options to set the modem DTE flow control. disable Disables all flow control. xonXoffSig Enables XON/XOFF signaling between modem and DTE. cts Enables the modem to flow control the DTE via CTS. rtsCts This option operates the same as CTS option as well as allowing RTS to flow control the modem as a ready to receive signal. xonOff Allows the modem to XON/XOFF the DTE yet ignore these signals when sent by the DTE (unidirectional flow control).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), xonXoffSig(2), cts(3), rtsCts(4), xonXoff(5)  

mdmTermEcho 1.3.6.1.4.1.498.4.2.1.8
Option to control the modem echo to the DTE.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

mdmDCDCntrl 1.3.6.1.4.1.498.4.2.1.9
Option the EIA DCD mode of operation. ForceOn DCD always ON. Real DCD will follow CCITT specifications. ForceOnToggleDisc DCD is On but toggle on disconnect as a signaling to the front end.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER forceOn(1), real(2), forceOnToggleDisc(3)  

mdmCTSCntrl 1.3.6.1.4.1.498.4.2.1.10
Option the EIA CTS mode of operation. cmdOnDataRTS On during command mode, during data mode will follow RTS. cmdOnDataReal On during command mode, during data mode will follow CCITT specifications. realCCITT It follows CCITT specifications always. ForceON On all the times.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER cmdOnDataRTS(1), cmdOnDataReal(2), realCCITT(3), forceOn(4)  

mdmDTRTrans 1.3.6.1.4.1.498.4.2.1.11
Option the modem to respond to loss of DTR. forceon Modem ignore DTR transitions. offInCmdMode Upon transition detection modem will enter command mode. offDisc Upon transition detection modem will disconnect. offDiscRecalUser Upon transition detection modem will disconect and recall the selected User configuration. This object is Country Code dependent.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER forceon(1), offInCmdMode(2), offDisc(3), offDiscRecallUser(4)  

mdmDSRCntrl 1.3.6.1.4.1.498.4.2.1.12
Option the EIA DSR mode of operation. onUntilDisc Selects DSR to remain On and glitch Off for disconnect. Normal Causes DSR to be real. followDCD Selects DSR to follow carrier detect. forceOn Selects DSR forced On in all modes.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER onUntilDisc(1), normal(2), followDCD(3), forceOn(4)  

mdmDSRCntrlAL 1.3.6.1.4.1.498.4.2.1.13
Option the EIA DSR operation during analoop. onAnaloop DSR will turn ON when in analoop offAnaloop DSR is forced Off when in Analoop.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER onAnaloop(1), offAnaloop(2)  

mdmTXClockSource 1.3.6.1.4.1.498.4.2.1.14
Selects the source for TX clock generation. internal The modem uses the internally generated clock source. external The modem uses the DTE clock as a source receiverwrap The modem receiver derived timing clock to be used in the transmitter.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER internal(1), external(2), receiverwrap(3)  

mdmRTSCTSDelay 1.3.6.1.4.1.498.4.2.1.15
Selects the delay time between RTS coming on and CTS being turned on (.001 sec).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

mdmCarriageReturnCharacter 1.3.6.1.4.1.498.4.2.1.16
Select the ascii character to be used as the carriage return.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..127  

mdmCharacterAbortDialing 1.3.6.1.4.1.498.4.2.1.17
Enable/disable the option to abort dialing if a DTE character is detected.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

mdmDelayDTR 1.3.6.1.4.1.498.4.2.1.18
Selects the delay time(in Seconds) between making data mode and raising the DTR lead. It is dependent on the mode of operation. When configured for &M0 this register is used to debounce the DTR signal. The default value is five hundredths of a second (0.05second). When configured for &M1 and in data mode, this register sets the time available to the operator to switch the EIA cable from asynchronous equipment to synchronous equipment. When the timer expires, this register is used to debounce the DTR signal as in &M0 mode. The default value is five seconds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

mdmEscapeCharacter 1.3.6.1.4.1.498.4.2.1.19
Select the ascii character to be used as the 'escape to command mode' character.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..127  

mdmLineFeedCharacter 1.3.6.1.4.1.498.4.2.1.20
Select the ascii character to be used as the Line Feed character.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..127  

mdmHangUpDelay 1.3.6.1.4.1.498.4.2.1.21
Select the delay time(in Sec) between the modem detecting a command to hang up the line and the disconnect operation.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

mdmEscapeCharacterGuardTime 1.3.6.1.4.1.498.4.2.1.22
This is the timer the modem will use when determining a valid escape sequence. Select the delay time(in 1/50 Sec). When a valid escape sequence is detected the modem will transfer from the data to command mode.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

mdmOperatingMode 1.3.6.1.4.1.498.4.2.1.23
Option to set the type of data transfer in data mode. asyncDataMode modem operates in async mode during command or data mode. async CmdsyncData In command mode the modem uses async data. In data mode operates in synchronous mode.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER asyncDataMode(1), asyncCmdsyncData(2)  

mdmBackSpaceCharacter 1.3.6.1.4.1.498.4.2.1.24
Select the ascii character to be used as the Back Space character.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..127  

mdmModemConfigTable 1.3.6.1.4.1.498.4.3
The GDC VFAST modem configuration table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MdmModemEntry

mdmModemEntry 1.3.6.1.4.1.498.4.3.1
A listing of GDC VFAST modem options.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MdmModemEntry  

mdmModemIndex 1.3.6.1.4.1.498.4.3.1.1
A unique index for the Modem Option Table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SCinstance  

mdmRingsToAns 1.3.6.1.4.1.498.4.3.1.2
Selects the number of rings received before the modem Auto Answer. This object is Country Code dependent
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

mdmFallFwrdBack 1.3.6.1.4.1.498.4.3.1.3
Command the modem to enable/disable rate negotiation during a retrain.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

mdmTrellis 1.3.6.1.4.1.498.4.3.1.4
Enable/disable Trellis negotiation during a handshake.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

mdmSQRetrain 1.3.6.1.4.1.498.4.3.1.5
Command to option Signal Quality Retrains.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), sQThree(2), sQForever(3)  

mdmLongSpaceDisc 1.3.6.1.4.1.498.4.3.1.6
Command to enable/disable Long Space Disconnect. enable The modem will transmit 4 seconds of continuous space (BREAK) when ever a disconnect request is detected. If the modem receives more than 1.5 seconds of continuous space (BREAK) while on-line, it will hang up.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

mdmMakeBusy 1.3.6.1.4.1.498.4.3.1.7
Command to option the switched network make busy function disable Does not make busy. onLossDTR Make busy on loss of DTR. inAL Make busy during analoop. inALorLossRTSorDTR Make busy in analoop, loss of RTS or DTR. This object is Country Code dependent
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), onLossDTR(2), inAL(3), inALorLossRTSorDTR(4), onLossRTS(5)  

mdmRDLOptions 1.3.6.1.4.1.498.4.3.1.8
Command to enable/disable Remote Digital Loopback Instigation. disable The modem ignores the inband request to initiate a remote digital loopback. enable The modem accept the inband request to initiated a remote digital loopback.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

mdmTestTimer 1.3.6.1.4.1.498.4.3.1.9
Command to limit any diagnostic test in 10 second intervals. When the value is zero the test runs forever.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

mdmDTETestCntrl 1.3.6.1.4.1.498.4.3.1.10
Command to enable/disable diagnostic tests from DTE interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

mdmDCDLossDisc 1.3.6.1.4.1.498.4.3.1.11
Command to set the time (0.1sec) between loss of carrier detected and a modem disconnect. This object is Country Code dependent.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

mdmCDRespTime 1.3.6.1.4.1.498.4.3.1.12
Command to set the time (in Sec) a carrier signal must be present for the modem to recognize it. This object is Country Code dependent.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

mdmAnswerOriginate 1.3.6.1.4.1.498.4.3.1.13
Command to set the handshake band. answerIfRingDetect Upon detecting a ring the modem will handshake in the answer mode. forceAnswer The modem will be force to handshake in the answer mode. autoAnswerInOriginate When the modem detect a ring it will answer in the originate mode.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER answerIfRingDetect(1), forceAnswer(2), autoAnswerInOriginate(3)  

mdmWaitForDCD 1.3.6.1.4.1.498.4.3.1.14
This object is used to store the carrier wait time. This is the time which the modem will wait after the dial has been completed until the modem senses carrier detect. It is also used for the dial command modifiers W wait for dial tone before dialing and @ wait for quiet answer before dialing. It also sets the amount of time the modem will wait for ringback when originating a call. This object is Country Code dependent.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..60  

mdmDialerConfigTable 1.3.6.1.4.1.498.4.4
The GDC VFAST dialer configuration table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MdmDialerEntry

mdmDialerEntry 1.3.6.1.4.1.498.4.4.1
A listing of GDC VFAST modem dialer options.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MdmDialerEntry  

mdmDialerIndex 1.3.6.1.4.1.498.4.4.1.1
A unique index for the Dialer Table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SCinstance  

mdmCPMMonitor 1.3.6.1.4.1.498.4.4.1.2
Command used to option the Call Progress Monitor operation. This object is Country Code dependent. basic The modem will blind dial and will only send a CONNECT message for all established links. All CPM is disabled. extendedNoCPM This command is the same as basic with the exception of the connect messages. The modem will send the appropiate connect response of CONNECT followed by the connected speed. extendedDialTone This command is the same as extendedNoCPM command but without blind dialing. The modem will send the NO DIALTONE message if dial tone is not detected. extendedBusy This command forces the modem to blind dial. The modem will not respond with the NO DIALTONE message while all other CPM responses are enabled. extendedFullCPM This command enables all CPM response codes and monitoring, except rinback detection. extendedFullCPMRingback This command enables all CPM response codes and monitoring, and includes ringback detection. This object is Country Code dependent.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER basic(1), extendedNoCPM(2), extendedDialtone(3), extendedBusy(4), extendedFullCPM(5), extendedFullCPMRingback(6)  

mdmParserSelection 1.3.6.1.4.1.498.4.4.1.3
Command used to select the DTE parser. The following parsers are available: AT, v25async, v25HDLC, v25bisync, and no parser
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER at(1), v25async(2), v25HDLC(3), v25bisync(4), noparser(5)  

mdmDTRDial 1.3.6.1.4.1.498.4.4.1.4
This command sets the modem operation upon detecting an Off to On transition on DTR. disable Transition is ignored. cellNumber0 Dial number stored in cell 0. cellNumber1 Dial number stored in cell 1. cellNumber2 Dial number stored in cell 2. cellNumber3 Dial number stored in cell 3. cellNumber4 Dial number stored in cell 4. cellNumber5 Dial number stored in cell 5. cellNumber6 Dial number stored in cell 6. cellNumber7 Dial number stored in cell 7. cellNumber8 Dial number stored in cell 8. cellNumber9 Dial number stored in cell 9. talkData Starts a handshake.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), cellNumber0(2), cellNumber1(3), cellNumber2(4), cellNumber3(5), cellNumber4(6), cellNumber5(7), cellNumber6(8), cellNumber7(9), cellNumber8(10), cellNumber9(11), talkData(12)  

mdmDialType 1.3.6.1.4.1.498.4.4.1.5
This command selects the type of dial. Pulse or DTMF dial. This object is Country Code dependent
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER pulse(1), dtmf(2)  

mdmResponseMode 1.3.6.1.4.1.498.4.4.1.6
This Command controls when to send responses. enabled Requests the non-quiet mode, that is, to transmit result codes to the DTE as appropriate. disabled Request the quiet mode which tells the modem not to send any result codes to the DTE. enableInOriginate Disables Call Progress Monitor responses in the answer mode only. This mode is entered on detection of ring signal.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), enableInOriginate(3)  

mdmResponseType 1.3.6.1.4.1.498.4.4.1.7
This command controls the type of responses. numeric modem responses are in numeric code. alpha modem responses are in alphabetical format.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER numeric(1), alpha(2)  

mdmPauseTime 1.3.6.1.4.1.498.4.4.1.8
This command selects the time for pause characters in the dial string. This object is Country Code dependent.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

mdmWaitForDialtoneTime 1.3.6.1.4.1.498.4.4.1.9
This command selects the time for the modem to be looking for dialtone before disconnecting. This object is Country Code dependent
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

mdmProtocolConfigTable 1.3.6.1.4.1.498.4.5
The GDC VFAST modem Protocol configuration table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MdmProtocolEntry

mdmProtocolEntry 1.3.6.1.4.1.498.4.5.1
A listing of GDC VFAST modem Protocol options.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MdmProtocolEntry  

mdmProtocolIndex 1.3.6.1.4.1.498.4.5.1.1
A unique index for the DTE Table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SCinstance  

mdmCompression 1.3.6.1.4.1.498.4.5.1.2
This command controls the Compression operation when operating in asynchronous mode. disabled No compression available. enabled Compression available in both directions. txpathonly Compression available in the transmitter path only when in V.42bis. In MNP 5 data compression is enabled in both directions. rxpathonly Compression available in the receiver path only when in V.42bis. In MNP 5 data compression is enabled in both directions.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2), txpathonly(3), rxpathonly(4)  

mdmAsyncProtocol 1.3.6.1.4.1.498.4.5.1.3
This command controls the Protocols available at the handshake. wire Options the modem to run in wire mode; copying characters from VF port to the DTE port and vice versa. direct Options the modem to run in direct mode; where the DTE and the VF speeds must match, and there is no speed buffering. Direct mode is V.14 asynchronous mode. mnpreliable This option limits error correction to MNP links only or hang up. autoreliable Options the mode to run in autoreliable mode, and the modem will negotiate V.42 or alternate links. With no link, the modem will enter wire mode (speed buffering). v42reliable This option limits error correction to a V.42 (LAPM) link or hang up. reliableLAPMorMNP This option will attempt either a V.42 (LAPM) or MNP link and if either link fails, the modem will hang up. V.13 This option selects V.13 simulated controlled carrier.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER wire(1), direct(2), mnpreliable(3), autoreliable(4), v42reliable(5), reliableLAPMorMNP(6), v13(7)  

mdmFlowControl 1.3.6.1.4.1.498.4.5.1.4
This command controls the flow control type between the modem and the DTE available at the handshake. disabled Disables modem to modem flow control. enabled Enables bidirectional modem flow control based on XON/XOFF signaling. These signals are detected, acted on and optionally deleted from the data stream. Unidirectional provides unidirectional flow control where a modem may send XON/XOFF signals to the remote modem, yet ignore and pass through any these VF received signals to its DTE. bidirectional Acts the same as enabled with the addition of the XON/XOFF pass through option being enabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2), unidirectional(3), bidirectional(4)  

mdmBreakHandling 1.3.6.1.4.1.498.4.5.1.5
This command controls the operation of breaks. expediteDest This option will immediately transmit a break character for a fix time (300 msec) and destroy any currently bufered data. expediteNonDest This option is the same as expediteDest except all buffered data will be save. nonExpediteNonDest This option will transmit a fixed time break character in sequence with the rest of the data. ignore Ignores all break received from the DTE. timedNonExoediteNonDest This option transmits break characters in sequence with the rest of the data for the duration the DTE is transmitting this character. timedNonExpediteNonDest2 Same as above.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER expediteDest(1), expediteNonDest(2), nonExpediteNonDest(3), ignored(4), timedNonExpediteNonDest(5), timedNonExpediteNonDest2(6)  

mdmConnAndLinkMessages 1.3.6.1.4.1.498.4.5.1.6
This command controls when to send the protocol messages. separateMessages This options the modem to send the standard GDC conect message upon reaching data mode plus V.42 message after the link negotiation. The connect message displays VF line speed. bothAfterLink With this option the connect and link messages are send after link negotiation. microcomCompatible This option is the same as bothAfterLink except adds a /RELIABLE at the end of the message when a V.42 error corrected link has been establish. connectAfterLink This option sends only the connect message after the link negotiation. The message will indicate the VF rate for V.13 and V.14 connections and the DTE rate for all other connections.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER separateMessages(1), bothAfterLink(2), microcomCompatible(3), connectAfterLink(4)  

mdmErrorCorrection 1.3.6.1.4.1.498.4.5.1.7
This command controls how the data is handled when running a protocol. noBuffer This option discards all data coming in from the modem until the receiver modem sends a PROTOCOL: NONE message to the DTE at which time data will be passed through. bufferRxData This option will buffer received data (up to 200 characters) until the PROTOCOL: NONE message is sent. The buffered data will be passed through to the DTE. The modem will fall back to wire mode if more than 200 characters have been received prior to establishing an error correction link. fallbackWithFallbackChar This command discards all incoming data until two consecutive fallback characters are detected at which point the receiver modem falls back to wire mode. One fallback character is passed through to its DTE as data. fallbackV14Buffer This option acts the same as bufferRxData except with no link it falls back to V.14 (direct)mode. fallbackV14WithFallbackChar This option acts as fallbackWithFallbackChar except it also falls back to V.14 (direct) mode.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noBuffer(1), bufferRxData(2), fallbackWithFallbackChar(3), fallbackV14Buffer(4), fallbackV14WithFallbackChar(5)  

mdmV13Mode 1.3.6.1.4.1.498.4.5.1.8
This command controls the V13 function. bidirectional Selects bidirectional V.13 simulated controlled carrier. txEnable Selects V.13 Tx side enabled. rxEnable Selects V.13 RX side enabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER bidirectional(1), txEnable(2), rxEnable(3)  

mdmSyncProtocol 1.3.6.1.4.1.498.4.5.1.9
This command controls the type of sync protocol. normalsync Selects normal synchronous mode. v13sync Selects synchronous V13 mode.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER normalsync(1), v13sync(2)  

mdmFrameRetransLimit 1.3.6.1.4.1.498.4.5.1.10
This command limits the number of times the modem will retransmit a frame while in an error correction connection.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

mdmPrivateLineConfigTable 1.3.6.1.4.1.498.4.6
The GDC VFAST modem Private Line configuration table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MdmPrivateLineEntry

mdmPrivateLineEntry 1.3.6.1.4.1.498.4.6.1
A listing of GDC VFAST Private Line configurations options.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MdmPrivateLineEntry  

mdmPrivateLineIndex 1.3.6.1.4.1.498.4.6.1.1
A unique index for the Private Line Configurations Table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SCinstance  

mdmPrivateLineTxLevel 1.3.6.1.4.1.498.4.6.1.2
This command selects the transmit level during Private Line operation. This object is Country Code dependent
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER dBm0(1), dBm1(2), dBm2(3), dBm3(4), dBm4(5), dBm5(6), dBm6(7), dBm7(8), dBm8(9), dBm9(10), dBm10(11), dBm11(12), dBm12(13), dBm13(14), dBm14(15), dBm15(16)  

mdmPrivateLineHandshakeMode 1.3.6.1.4.1.498.4.6.1.3
This command selects the Private Line Handshake modes
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER gdcVfastonly(1), v32bisonly(2), v32only(3)  

mdmAutoDialRestoral 1.3.6.1.4.1.498.4.6.1.4
This command selects the options for Auto Dial Restoral when the modem is in private line mode. disabled No Auto Dial Restoral allowed. enableWithEndOfSession Enable Auto Dial Restoral with line failure indicator. enableWithoutEnOfSession Enable Auto Dial Restoral without line failure indicator.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enableWithEndOfSession(2), enableWithoutEndOfSession(3)  

mdmPrivateLineDownTime 1.3.6.1.4.1.498.4.6.1.5
This command selects for how long the Private Line must be lost before going to Dial Back Up mode
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

mdmDBUtoPLLookbackTime 1.3.6.1.4.1.498.4.6.1.6
This command selects the time for how often the modem must lookback for Private Line restoral. The units are in 10 minutes. Valid range from 0 to 255. When the value 0 is selected this option is disabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

mdmAlarmScanTable 1.3.6.1.4.1.498.4.7
The GDC VFAST alarm Scan Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MdmAlarmScanEntry

mdmAlarmScanEntry 1.3.6.1.4.1.498.4.7.1
An entry in the GDC VFAST alarm table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MdmAlarmScanEntry  

mdmAlarmScanIndex 1.3.6.1.4.1.498.4.7.1.1
This object is the identifier of the VFAST alarm table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SCinstance  

mdmAlarmScan 1.3.6.1.4.1.498.4.7.1.2
Reads the alarm scan. There are 8 bytes. byte 1 bit 4 (bit 1.4) No DTR signal bit 2.0 No TXD Transitions bit 2.2 No RXD Transitions bit 2.3 Modem Fallback bit 2.6 Modem on Dial Back Up bit 3.2 Power Up bit 4.0 Poor Signal Quality bit 5.3 DCD Loss bit 6.0-6 no alarms bit 7.0 Modem Configuration Checksum Error bit 7.1 Call Failed bit 7.2 Call Length Exceeded Maximum Allowed bit 7.3 Retrain Count Exceeded Threshold bit 7.4 Ring No Answer bit 7.5 Remote Configuration session active bit 7.6 Test timeout bit 8.0-6 no alarms
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(8)  

mdmResetSelfPowerBit 1.3.6.1.4.1.498.4.7.1.3
This resets the modem power up alarm.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER reset(1)  

mdmMaskAlarmTable 1.3.6.1.4.1.498.4.8
The GDC VFAST alarm Mask Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MdmMaskAlarmEntry

mdmMaskAlarmEntry 1.3.6.1.4.1.498.4.8.1
An entry in the GDC VFAST alarm mask table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MdmMaskAlarmEntry  

mdmMaskAlarmIndex 1.3.6.1.4.1.498.4.8.1.1
This object is the index of the VFAST alarm mask table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SCinstance  

mdmDTRLoss 1.3.6.1.4.1.498.4.8.1.2
Mask for loss of DTR alarm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER mask(1), unmask(2)  

mdmFallback 1.3.6.1.4.1.498.4.8.1.3
Mask for fallback alarm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER mask(1), unmask(2)  

mdmRxdTran 1.3.6.1.4.1.498.4.8.1.4
Mask for Receive data transitions alarm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER mask(1), unmask(2)  

mdmTxdTran 1.3.6.1.4.1.498.4.8.1.5
Mask for transmit data transitions alarm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER mask(1), unmask(2)  

mdmDCDLoss 1.3.6.1.4.1.498.4.8.1.6
Mask for loss of DCD alarm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER mask(1), unmask(2)  

mdmRingNoAnswer 1.3.6.1.4.1.498.4.8.1.7
Mask for Rings no Answer alarm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER mask(1), unmask(2)  

mdmRetrain 1.3.6.1.4.1.498.4.8.1.8
Mask for Retrains count exceeded alarm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER mask(1), unmask(2)  

mdmCallLength 1.3.6.1.4.1.498.4.8.1.9
Mask for Call Length exceeded alarm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER mask(1), unmask(2)  

mdmCallFail 1.3.6.1.4.1.498.4.8.1.10
Mask for Call Failed alarm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER mask(1), unmask(2)  

mdmConfigErr 1.3.6.1.4.1.498.4.8.1.11
Mask for Configuration checksum error alarm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER mask(1), unmask(2)  

mdmSignalQuality 1.3.6.1.4.1.498.4.8.1.12
Mask for Poor Signal Quality alarm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER mask(1), unmask(2)  

mdmOnDBU 1.3.6.1.4.1.498.4.8.1.13
Mask for On Dial Backup alarm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER mask(1), unmask(2)  

mdmRemoteConfigMask 1.3.6.1.4.1.498.4.8.1.14
Mask for Remote Configuration.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER mask(1), unmask(2)  

mdmTestTimeout 1.3.6.1.4.1.498.4.8.1.15
Mask for Test timeout.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER mask(1), unmask(2)  

mdmThresholdsTable 1.3.6.1.4.1.498.4.9
The GDC VFAST Alarm Thresholds Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MdmThresholdsEntry

mdmThresholdsEntry 1.3.6.1.4.1.498.4.9.1
An entry in the GDC VFAST Alarm Thresholds table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MdmThresholdsEntry  

mdmThresholdsIndex 1.3.6.1.4.1.498.4.9.1.1
This object is the identifier of the Thresholds table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SCinstance  

mdmCallDuration 1.3.6.1.4.1.498.4.9.1.2
This option selects the call duration threshold for alarm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  TimeTicks  

mdmRetrainThreshold 1.3.6.1.4.1.498.4.9.1.3
This option selects the number of retrains threshold for alarm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

mdmStatusTable 1.3.6.1.4.1.498.4.10
The GDC VFAST Status Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MdmStatusEntry

mdmStatusEntry 1.3.6.1.4.1.498.4.10.1
An entry in the GDC VFAST Status table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MdmStatusEntry  

mdmStatusIndex 1.3.6.1.4.1.498.4.10.1.1
This object is the identifier of the VFAST Status table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SCinstance  

mdmPLLookbackStatus 1.3.6.1.4.1.498.4.10.1.2
Shows the status of Private Line lookback.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

mdmAutoDialRestoralStatus 1.3.6.1.4.1.498.4.10.1.3
Shows the status of Auto Dial Restoral.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

mdmTXDtransitions 1.3.6.1.4.1.498.4.10.1.4
EIA Status of TXD data transitions.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notransition(1), transition(2)  

mdmRXDtransitions 1.3.6.1.4.1.498.4.10.1.5
EIA Status of RXD data transitions.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notransition(1), transition(2)  

mdmRTStransitions 1.3.6.1.4.1.498.4.10.1.6
EIA Status of Request to Send transitions.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notransition(1), transition(2)  

mdmDTRtransitions 1.3.6.1.4.1.498.4.10.1.7
EIA Status of Data Terminal Ready transitions.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notransition(1), transition(2)  

mdmDCDtransitions 1.3.6.1.4.1.498.4.10.1.8
EIA Status of Carrier Detect transitions.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notransition(1), transition(2)  

mdmTXCLKtransitions 1.3.6.1.4.1.498.4.10.1.9
EIA Status Transmit Clock transitions.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notransition(1), transition(2)  

mdmDTR 1.3.6.1.4.1.498.4.10.1.10
EIA Status of Data Terminal Ready.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(1), on(2)  

mdmCTS 1.3.6.1.4.1.498.4.10.1.11
EIA Status of Clear to Send.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(1), on(2)  

mdmDSR 1.3.6.1.4.1.498.4.10.1.12
EIA Status of Data Set Ready.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(1), on(2)  

mdmDCD 1.3.6.1.4.1.498.4.10.1.13
EIA Status of Carrier Detect.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(1), on(2)  

mdmSQM 1.3.6.1.4.1.498.4.10.1.14
EIA Status of Signal Quality.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(1), on(2)  

mdmRTS 1.3.6.1.4.1.498.4.10.1.15
EIA Status of Request to Send.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(1), on(2)  

mdmSwitchedPrivate 1.3.6.1.4.1.498.4.10.1.16
Switched Network or Private Line configuration setting.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER switchedNetwork(1), privateLine(2)  

mdmControlTable 1.3.6.1.4.1.498.4.11
The GDC VFAST Control Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MdmControlEntry

mdmControlEntry 1.3.6.1.4.1.498.4.11.1
An entry in the GDC VFAST Control table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MdmControlEntry  

mdmControlIndex 1.3.6.1.4.1.498.4.11.1.1
This object is the identifier of the VFAST Control table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SCinstance  

mdmSoftReset 1.3.6.1.4.1.498.4.11.1.2
Forces a soft reset on the modem. Not applicable when the modem is in Remote Configuration session.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER reset(1)  

mdmFrontPanel 1.3.6.1.4.1.498.4.11.1.3
This command controls the functionality of the front panel Switches.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER inhibit(1), enabled(2)  

mdmMakeClearBusy 1.3.6.1.4.1.498.4.11.1.4
Command used to control the Offhook relay to make busy or clear the VF line. Not applicable when the modem is in Remote Configuration session.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER onHook(1), offHook(2)  

mdmPLTalkData 1.3.6.1.4.1.498.4.11.1.5
Object is used to force the modem to the idle or data state while configured for Private line. Idle, allows the modem to activate the private line option. Data, forces the modem to retrain.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER idle(1), data(2)  

mdmWhatAreYouTable 1.3.6.1.4.1.498.4.12
The GDC VFAST What Are You Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MdmWhatAreYouEntry

mdmWhatAreYouEntry 1.3.6.1.4.1.498.4.12.1
An entry in the GDC VFAST What Are You table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MdmWhatAreYouEntry  

mdmWhatAreYouIndex 1.3.6.1.4.1.498.4.12.1.1
This object is the identifier of the VFAST What Are You table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SCinstance  

mdmVFCard 1.3.6.1.4.1.498.4.12.1.2
This function returns the value the VF card attached to the modem.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER domestic(1), cardA(65), cardB(66), cardC(67), cardD(68), cardE(69), cardF(70), cardG(71), cardH(72), cardJ(74), cardK(75), cardL(76), cardM(77), cardN(78), cardP(80), cardR(82), noCard(127)  

mdmDTECard 1.3.6.1.4.1.498.4.12.1.3
This function returns the type of DTE card attached to the modem.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER v35(1), eia530(2), eia232(3)  

mdmProductCode 1.3.6.1.4.1.498.4.12.1.4
This identifies what type of device this is.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER dmsVfast(23)  

mdmCodeRev 1.3.6.1.4.1.498.4.12.1.5
This function returns the firmware code level. example 01 - A- 02 - B-
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(2)  

mdmBootRev 1.3.6.1.4.1.498.4.12.1.6
This function returns the boot firmware level. example 01 - A- 02 - B-
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(2)  

mdmCountryCode 1.3.6.1.4.1.498.4.12.1.7
This function returns the country code number in three bytes. Each byte is the hex value of an decimal number. Example hex 30,30,31 is the country code of USA 001 30,34,34 is the country code of UK 044
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(3)  

mdmDiagnosticTable 1.3.6.1.4.1.498.4.13
The GDC VFAST diagnostics table. Not applicable when the modem is in Remote Configuration session.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MdmDiagnosticEntry

mdmDiagnosticEntry 1.3.6.1.4.1.498.4.13.1
A listing of GDC VFAST diagnostic tests
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MdmDiagnosticEntry  

mdmDiagnosticIndex 1.3.6.1.4.1.498.4.13.1.1
A unique index for the Diagnostic Table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SCinstance  

mdmDiagnosticTest 1.3.6.1.4.1.498.4.13.1.2
This function selects the test. Not applicable when the modem is in Remote Configuration session.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER terminateTest(1), analoop(2), analoopSelfTest(3), remoteDigitalLoop(4), remoteDigitalLoopSelfTest(5), selfTest(6), digitalLoop(7)  

mdmDiagnosticResults 1.3.6.1.4.1.498.4.13.1.3
This function reads the test results in bit errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

mdmDiagnosticStatus 1.3.6.1.4.1.498.4.13.1.4
Diagnostic status of which test is running. Not applicable when the modem is in Remote Configuration session.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER rmtDigLpHsk(1), inboundRmtDigLp(2), rmtDigLp(4), localDigLp(8), analoopHsk(16), analoop(32), selftest(64), rmtDigLpSelftest(68), analoopSelftest(96), notInTest(97)  

mdmTestStatus 1.3.6.1.4.1.498.4.13.1.5
Test Status canNotBeDone - means test can not be done at this time terminated - means the test was terminated, could be terminated via the front panel timedout - the modem's test timer expired noPrevStatus - means that no status is currently available Not applicable when the modem is in Remote Configuration session.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER canNotBeDone(4), terminated(8), timedout(16), noPrevStatus(17)  

mdmTestDuration 1.3.6.1.4.1.498.4.13.1.6
Time of modem in test, counted in timeticks. Not applicable when the modem is in Remote Configuration session.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

mdmDialingFunctionTable 1.3.6.1.4.1.498.4.14
The GDC VFAST modem dialing function table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MdmDialingFunctionEntry

mdmDialingFunctionEntry 1.3.6.1.4.1.498.4.14.1
A listing of GDC VFAST modem dialing function parameters.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MdmDialingFunctionEntry  

mdmDialFunctionIndex 1.3.6.1.4.1.498.4.14.1.1
A unique index for the Dialing Function Table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SCinstance  

mdmManualDial 1.3.6.1.4.1.498.4.14.1.2
Command to instruct the modem to dial the following number, n. Not applicable when modem in remote configuration session.
Status: mandatory Access: write-only
OBJECT-TYPE    
  DisplayString Size(1..36)  

mdmTerminateCall 1.3.6.1.4.1.498.4.14.1.3
Command to instruct the mode to disconnect the call and go to idle.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER goOnhook(1)  

mdmDialStatus 1.3.6.1.4.1.498.4.14.1.4
Dial Status information 'inTest' means the modem is currently in a test mode.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disconnect(1), idle(2), dial(4), training(8), retrain(16), data(32), inTest(33)  

mdmCallProgressStatus 1.3.6.1.4.1.498.4.14.1.5
Call Progress Status
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ringback(1), incomingRing(2), busy(4), noAnswer(8), ringAndNoAnswer(10), noCarrier(16), ringbackNoCarrier(17), ringNoCarrier(18), ringNoCarrier2(19), noDialtone(32), noLoopCurrent(64), unobtainableNumber(128), connect(256), connectRingback(257), connectIncomingRing(258), connectIncomingRing2(259), noPrevStatus(260)  

mdmDialingCellsFunctionTable 1.3.6.1.4.1.498.4.15
The GDC VFAST modem dialing cells function table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MdmDialingCellsFunctionEntry

mdmDialingCellsFunctionEntry 1.3.6.1.4.1.498.4.15.1
A listing of GDC VFAST modem dialing cells function parameters.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MdmDialingCellsFunctionEntry  

mdmDialCellFunctionIndex 1.3.6.1.4.1.498.4.15.1.1
A unique index for the Dialing Function Table. Not applicable when modem in remote configuration session.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SCinstance  

mdmCellNumber 1.3.6.1.4.1.498.4.15.1.2
Command to instruct the modem to attempt dialing the phone number stored in Cell n. Not applicable when modem in remote configuration session.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

mdmDial 1.3.6.1.4.1.498.4.15.1.3
Command modem to dial. Not applicable when modem in remote configuration session.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER goDial(1)  

mdmCellPhoneNumber 1.3.6.1.4.1.498.4.15.1.4
Command to cause the modem to display the phone number stored in any of the 10 dial cell locations (0-9).
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..36)  

mdmTerminateCellCall 1.3.6.1.4.1.498.4.15.1.5
Command to instruct the mode to disconnect the call and go to idle.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER goOnhook(1)  

mdmMaintenanceTable 1.3.6.1.4.1.498.4.16
The GDC VFAST Maintenance Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MdmMaintenanceEntry

mdmMaintenanceEntry 1.3.6.1.4.1.498.4.16.1
An entry in the GDC VFAST Maintenance table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MdmMaintenanceEntry  

mdmMaintenanceIndex 1.3.6.1.4.1.498.4.16.1.1
A unique index for the Maintenance Index Table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SCinstance  

mdmSaveRecallConfig 1.3.6.1.4.1.498.4.16.1.2
This command allows the user to load or save factory or user profile configurations into the modem.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER recallFactoryDefault0(1), recallFactoryDefault1(2), recallFactoryDefault2(3), recallFactoryDefault3(4), recallUserProfile0(5), recallUserProfile1(6), recallUserProfile2(7), recallUserProfile3(8), saveUserProfile0(9), saveUserProfile1(10), saveUserProfile2(11), saveUserProfile3(12)  

mdmConfigCksum 1.3.6.1.4.1.498.4.16.1.3
Reads the configuration checksum of the modem.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2)  

mdmPassword 1.3.6.1.4.1.498.4.16.1.4
This function sets the modem password. The maximum number of digits in the password must be equal or less than 10. If no password is entered the password is non-functional.
Status: mandatory Access: write-only
OBJECT-TYPE    
  DisplayString Size(0..10)  

mdmSerialNumber 1.3.6.1.4.1.498.4.16.1.5
Network element serial number
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(16)  

mdmPowerUpProfile 1.3.6.1.4.1.498.4.16.1.6
Command to select 1 of 4 custom modem configurations at power up.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER zero(1), one(2), two(3), three(4)  

mdmPasswordOperation 1.3.6.1.4.1.498.4.16.1.7
This object identifies the Password Operation. The GDC proprietary handshake password validation operation and the on line (entered by the remote user) password validation operation can be enabled or disabled globally or selectively. disabled - password operations disabled enablehandshake - enable the handshake password operation enableonline - enable the answering modem to locally validate the remote user entered password enable - enable both handshake and online password operations Not applicable when the modem is in Remote Configuration session.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enablehandshake(2), enableonline(3), enable(4)  

mdmStatisticsTable 1.3.6.1.4.1.498.4.17
The GDC VFAST Statistics Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MdmStatisticsEntry

mdmStatisticsEntry 1.3.6.1.4.1.498.4.17.1
An entry in the GDC VFAST Statistics table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MdmStatisticsEntry  

mdmStatisticsIndex 1.3.6.1.4.1.498.4.17.1.1
This object is the identifier of the VFAST Statistics table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SCinstance  

mdmDCERate 1.3.6.1.4.1.498.4.17.1.2
This object identifies the DCE speed that the modem is operating.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER bps300(2), bps1200(3), bps2400(4), bps4800(5), bps7200(6), bps9600(7), bps12000(8), bps14400(9), bps16800(10), bps19200(11), bps21600(12), bps24000(13), bps26400(14), bps28800(15)  

mdmCallDurationStat 1.3.6.1.4.1.498.4.17.1.3
This function reads the duration of the last or current Switched Network connection in timeticks.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

mdmRetrainCount 1.3.6.1.4.1.498.4.17.1.4
This function reads the number of retrains.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..127  

mdmFallbackCount 1.3.6.1.4.1.498.4.17.1.5
This function reads the number of times that the modem falls back.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..127  

mdmFallforwardCount 1.3.6.1.4.1.498.4.17.1.6
This function reads the number of times that the modem falls forward.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..127  

mdmRxSignalLevel 1.3.6.1.4.1.498.4.17.1.7
This function reads the input signal level in dB.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..127  

mdmSignaltoNoiseRatio 1.3.6.1.4.1.498.4.17.1.8
This function reads the signal to noise ratio in dB.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..127  

mdmAnswerOriginateStat 1.3.6.1.4.1.498.4.17.1.9
This function reads the band that the modem is operating in data mode.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER originate(1), answer(2)  

mdmDiscReason 1.3.6.1.4.1.498.4.17.1.10
This function reads the reason why the modem has disconnected. usertimeout - user timed out while entering prompted information.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER usertimeout(1), unknown(2)  

mdmCompressionEfficiency 1.3.6.1.4.1.498.4.17.1.11
The number of bytes transferred into the compression encoder divided by the number of bytes transferred out of the encoder, multiplied by 100 for either the current or last call. If a data compression protocol is not in use, this value shall be '100'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

mdmThruput 1.3.6.1.4.1.498.4.17.1.12
The data thruput rate is the number of bytes received from the DCE and then sent to the DTE per second.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

mdmRemoteConfigTable 1.3.6.1.4.1.498.4.18
The GDC VFAST Remote Configuration Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MdmRemoteConfigEntry

mdmRemoteConfigEntry 1.3.6.1.4.1.498.4.18.1
An entry in the GDC VFAST Remote Config table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  MdmRemoteConfigEntry  

mdmRemoteConfigIndex 1.3.6.1.4.1.498.4.18.1.1
This object is the identifier of the VFAST Remote Configuration table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SCinstance  

mdmRemoteConfiguration 1.3.6.1.4.1.498.4.18.1.2
This object options the Remote configuration for the local unit before dial.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enableDTE(2), enableDMS(3)  

mdmEndRemoteConfiguration 1.3.6.1.4.1.498.4.18.1.3
This option tells the far end unit to disconnect and update the options or not that have been changed during the remote configuration session.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER noUpdate(1), update(2)  

mdmPasswordRemoteConfiguration 1.3.6.1.4.1.498.4.18.1.4
This option stores the Remote Configuration Password. When a password is stored in the answer modem it must be matched during the handshake by the originating modem. If the password matching fails, the answer modem will drop the connection. Not applicable when the modem is in Remote Configuration session.
Status: mandatory Access: write-only
OBJECT-TYPE    
  DisplayString Size(0..10)  

mdmMIBVersion 1.3.6.1.4.1.498.4.19
The version number of the MIB, to allow products to know which MIB is being supported. The version number will be x.yzT where x is a major revision (1-9), y is a minor revision(0-9), z is a typo revision (0-9) and T indicates the MIB is still a test revision(A-Z). When a release is complete no T should exist.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(5)  

mdmCallStatsTrap 1
This is the Call Statistics Trap. When a V.F 28.8 modem disconnects from a call after data has passed, it will send call statistics information.
TRAP-TYPE