Fore-Profile-MIB

File: Fore-Profile-MIB.mib (49243 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC Fore-Common-MIB

Imported symbols

Integer32 OBJECT-TYPE MODULE-IDENTITY
DisplayString RowStatus frameInternetworking

Defined Types

ProfileLmiEntry  
SEQUENCE    
  profileLmiIndex Integer32
  profileLmiRowStatus RowStatus
  profileLmiName DisplayString
  profileLmiFlavour INTEGER
  profileLmiT391 Integer32
  profileLmiN391 Integer32
  profileLmiT392 Integer32
  profileLmiN392 Integer32
  profileLmiN393 Integer32
  profileLminT3 Integer32
  profileLmiDirection INTEGER
  profileLmiRole INTEGER
  profileLmiRefCnt Integer32

ProfileFrRateEntry  
SEQUENCE    
  profileFrRateIndex Integer32
  profileFrRateRowStatus RowStatus
  profileFrRateName DisplayString
  profileFrRateInBc Integer32
  profileFrRateInBe Integer32
  profileFrRateInCir Integer32
  profileFrRateOutBc Integer32
  profileFrRateOutBe Integer32
  profileFrRateOutCir Integer32
  profileFrRateMinBc Integer32
  profileFrRateCmPeriod Integer32
  profileFrRateRefCnt Integer32

ProfileFuniEntry  
SEQUENCE    
  profileFuniIndex Integer32
  profileFuniRowStatus RowStatus
  profileFuniName DisplayString
  profileFuniIlmiVpi Integer32
  profileFuniIlmiVci Integer32
  profileFuniSigVpi Integer32
  profileFuniSigVci Integer32
  profileFuniMinVci Integer32
  profileFuniMaxVci Integer32
  profileFuniIlmiSupport INTEGER
  profileFuniSigSupport INTEGER
  profileFuniOamSupport INTEGER
  profileFuniActiveVpiBits Integer32
  profileFuniActiveVciBits Integer32
  profileFuniConfMode INTEGER
  profileFuniFcsBits INTEGER
  profileFuniHdrBytes INTEGER
  profileFuniAal34Support INTEGER
  profileFuniRefCnt Integer32

ProfileFrf8Entry  
SEQUENCE    
  profileFrf8Index Integer32
  profileFrf8RowStatus RowStatus
  profileFrf8Name DisplayString
  profileFrf8DeMode INTEGER
  profileFrf8ClpMode INTEGER
  profileFrf8FecnMode INTEGER
  profileFrf8DefaultDe Integer32
  profileFrf8DefaultClp Integer32
  profileFrf8Protocols Integer32
  profileFrf8RefCnt Integer32

ProfileServiceEntry  
SEQUENCE    
  profileServiceIndex Integer32
  profileServiceRowStatus RowStatus
  profileServiceName DisplayString
  profileServiceAccRate Integer32
  profileServiceMaxPayloadSize Integer32
  profileServiceMaxVccs Integer32
  profileServiceInBwOb Integer32
  profileServiceOutBwOb Integer32
  profileServiceRefCnt Integer32

ProfileEpdPpdEntry  
SEQUENCE    
  profileEpdPpdIndex Integer32
  profileEpdPpdRowStatus RowStatus
  profileEpdPpdName DisplayString
  profileEpdPpdPriority INTEGER
  profileEpdPpdClp0Epd INTEGER
  profileEpdPpdClp1Ppd INTEGER
  profileEpdPpdClp1Epd INTEGER
  profileEpdPpdRefCnt Integer32

ProfileFrf5Entry  
SEQUENCE    
  profileFrf5Index INTEGER
  profileFrf5RowStatus RowStatus
  profileFrf5Name DisplayString
  profileFrf5DeMode INTEGER
  profileFrf5ClpFrsscsDeMode INTEGER
  profileFrf5DefaultClp INTEGER
  profileFrf5MaxPayloadSize INTEGER
  profileFrf5MaxDlcis INTEGER
  profileFrf5RefCnt INTEGER

Defined Values

foreProfileModule 1.3.6.1.4.1.326.1.16.4
This MIB module defines several profile tables that facilitate the creation of FR/ATM and FUNI services and connections.
MODULE-IDENTITY    

profileLmiTable 1.3.6.1.4.1.326.1.16.4.1
The LMI profile table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ProfileLmiEntry

profileLmiEntry 1.3.6.1.4.1.326.1.16.4.1.1
An entry in the LMI profile table.
Status: current Access: not-accessible
OBJECT-TYPE    
  ProfileLmiEntry  

profileLmiIndex 1.3.6.1.4.1.326.1.16.4.1.1.1
This objects identifies the index of a profile entry in this table.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

profileLmiRowStatus 1.3.6.1.4.1.326.1.16.4.1.1.2
This object is used to create new rows and delete existing rows in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

profileLmiName 1.3.6.1.4.1.326.1.16.4.1.1.3
This object specifies the symbolic name assigned to this profile for user reference.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

profileLmiFlavour 1.3.6.1.4.1.326.1.16.4.1.1.4
This object specifies the type of the LMI protocol used over this FR service. This object corresponds to frLportVCSigProtocol in RFC1604 and frDlcmiState in RFC1315.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER none(1), lmi(2), t1617d(3), t1617b(4), q933a(5)  

profileLmiT391 1.3.6.1.4.1.326.1.16.4.1.1.5
The value of this object identifies the User-side T391 link integrity verification polling timer value (in seconds) for this UNI/NNI logical port. If the logical port is not performing user-side procedures, then this value is equal to noSuchName. This object applies to Q.933 Annex A and T1.617 Annex D. This object corresponds to frMgtVCSigUserT391 in RFC1604 and frDlcmiPollingInterval in RFC1315.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 5..30  

profileLmiN391 1.3.6.1.4.1.326.1.16.4.1.1.6
The value of this object identifies the User-side N391 full status polling cycle value for this UNI/NNI logical port. If the logical port is not performing user-side procedures, then this value is equal to noSuchName. This object applies to Q.933 Annex A and T1.617 Annex D. This object corresponds to frMgtVCSigUserN391 in RFC1604 and frDlcmiFullEnquiryInterval.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..255  

profileLmiT392 1.3.6.1.4.1.326.1.16.4.1.1.7
The value of this object identifies the Network- side T392 polling verification timer value in seconds (nT2 for LMI) for this UNI/NNI logical port. If the logical port is not performing network-side procedures, then this value is equal to noSuchName. This object applies to Q.933 Annex A, LMI and T1.617 Annex D. This object corresponds to frMgtVCSigNetT392 in RFC1604.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 5..30  

profileLmiN392 1.3.6.1.4.1.326.1.16.4.1.1.8
The value of this object identifies the Network- side N392 error threshold value (nN2 for LMI) for this UNI/NNI logical port. If the logical port is not performing network-side procedures, then this value is equal to noSuchName. This object applies to Q.933 Annex A, T1.617 Annex D and LMI. This object corresponds to frMgtVCSigNetN392 and frMgtVCSigUserN392 when the LMI role is network and user respectively in RFC1604, and frDlcmiErrorThreshold in RFC1315.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..10  

profileLmiN393 1.3.6.1.4.1.326.1.16.4.1.1.9
The value of this object identifies the Network- side N393 monitored events count value (nN3 for LMI) for this UNI/NNI logical port. If the logical port is not performing network-side procedures, then this value is equal to noSuchName. This object applies to Q.933 Annex A, LMI and T1.617 Annex D. This object corresponds to frMgtVCSigNetN393 and frMgtVCSigUserN393 when the LMI role is network and user respectively in RFC1604, and frDlcmiMonitoredEvents in RFC1315.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..10  

profileLminT3 1.3.6.1.4.1.326.1.16.4.1.1.10
The value of this object identifies the Network-side nT3 timer in seconds (for nN4 status enquires received) value for this FR service. This object applies only to LMI(STRATACOM) flavour. The allowable values include 5, 10, 15, 20, 25 and 30 seconds. This object corresponds to frMgtVCSigNetnT3 in RFC1604.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 5 | 10 | 15 | 20 | 25 | 30  

profileLmiDirection 1.3.6.1.4.1.326.1.16.4.1.1.11
The value of this object identifies the Local In-Channel Signaling Procedure that is used for this UNI/NNI logical port. The UNI/NNI logical port can be performing only user-to-network network-side procedures or bidirectional procedures.This object corresponds to frMgtVCSigProced in RFC1604.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER uni(1), bi(2)  

profileLmiRole 1.3.6.1.4.1.326.1.16.4.1.1.12
This object specifies the role of operation of this FR service - user (DTE) or network (DCE)
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER user(1), network(2)  

profileLmiRefCnt 1.3.6.1.4.1.326.1.16.4.1.1.13
This object identifies the number of services that are currently referring to this profile.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

profileFrRateTable 1.3.6.1.4.1.326.1.16.4.2
The FR rate profile table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ProfileFrRateEntry

profileFrRateEntry 1.3.6.1.4.1.326.1.16.4.2.1
An entry in the FR rate profile table.
Status: current Access: not-accessible
OBJECT-TYPE    
  ProfileFrRateEntry  

profileFrRateIndex 1.3.6.1.4.1.326.1.16.4.2.1.1
This object identifies the index of a profile entry in this table.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

profileFrRateRowStatus 1.3.6.1.4.1.326.1.16.4.2.1.2
This object is used to create new rows and delete existing rows in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

profileFrRateName 1.3.6.1.4.1.326.1.16.4.2.1.3
This object identifies the symbolic name assigned to this profile used for user reference.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

profileFrRateInBc 1.3.6.1.4.1.326.1.16.4.2.1.4
This object represents the committed burst size (bits) in the ingress direction of a connection. This object corresponds to frPVCEndptInBc in RFC1604 and frCircuitCommittedBurst in RFC1315.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

profileFrRateInBe 1.3.6.1.4.1.326.1.16.4.2.1.5
This object represents the excess burst size (bits) in the ingress direction of a connection. This object corresponds to frPVCEndptInBe in RFC1604 and frCircuitExcessBurst in RFC1315.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

profileFrRateInCir 1.3.6.1.4.1.326.1.16.4.2.1.6
This object represents the committed information rate (kbps) in the ingress direction of a connection. This object corresponds to frPVCEndptInCIR in RFC1604 and frCircuitThroughput in RFC1315.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

profileFrRateOutBc 1.3.6.1.4.1.326.1.16.4.2.1.7
This object represents the committed burst size (bits) in the egress direction of a connection. This object corresponds frPVCEndptOutBc in RFC1604.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

profileFrRateOutBe 1.3.6.1.4.1.326.1.16.4.2.1.8
This object represents the excess burst size (bits) in the egress direction of a connection. This object corresponds frPVCEndptOutBe in RFC1604.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

profileFrRateOutCir 1.3.6.1.4.1.326.1.16.4.2.1.9
This object represents the committed information rate (kbps) in the egress direction of a connection. This object corresponds frPVCEndptOutCIR in RFC1604.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

profileFrRateMinBc 1.3.6.1.4.1.326.1.16.4.2.1.10
This object represents the minimum committed burst size (bits) which can be set on a connection by rate adaptation.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

profileFrRateCmPeriod 1.3.6.1.4.1.326.1.16.4.2.1.11
This object represents the time period (msec) during which BECNs are monitored before the rate adaptation mechanism decides to change the current committed burst size in the egress direction.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

profileFrRateRefCnt 1.3.6.1.4.1.326.1.16.4.2.1.12
This object identifies the number of connections that are currently referring to this profile entry.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

profileFuniTable 1.3.6.1.4.1.326.1.16.4.3
The FUNI profile table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ProfileFuniEntry

profileFuniEntry 1.3.6.1.4.1.326.1.16.4.3.1
An entry in the FUNI profile table.
Status: current Access: not-accessible
OBJECT-TYPE    
  ProfileFuniEntry  

profileFuniIndex 1.3.6.1.4.1.326.1.16.4.3.1.1
This object identifies the index of a profile entry in this table.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

profileFuniRowStatus 1.3.6.1.4.1.326.1.16.4.3.1.2
This object is used to create new rows and delete existing rows in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

profileFuniName 1.3.6.1.4.1.326.1.16.4.3.1.3
This object specifies the symbolic name assigned to this profile for user reference.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

profileFuniIlmiVpi 1.3.6.1.4.1.326.1.16.4.3.1.4
This object represents VPI value used by ILMI over this FUNI interface. This object corresponds to funiIfConfIlmiVpi in FUNI MIB.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

profileFuniIlmiVci 1.3.6.1.4.1.326.1.16.4.3.1.5
This object represents VCI value used by ILMI over this FUNI service. This object corresponds to funiIfConfIlmiVci in FUNI MIB.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

profileFuniSigVpi 1.3.6.1.4.1.326.1.16.4.3.1.6
This object represents VPI value used for the signalling channel over this FUNI service. This object corresponds to funiIfConfSigVpi in FUNI MIB.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

profileFuniSigVci 1.3.6.1.4.1.326.1.16.4.3.1.7
This object represents VCI value used for the signalling channel over this FUNI service. This object corresponds to funiIfConfSigVci in FUNI MIB.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

profileFuniMinVci 1.3.6.1.4.1.326.1.16.4.3.1.8
This object represents minimal numeric value allowed to be used as a VCI on any user connection over this FUNI service.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 32..63  

profileFuniMaxVci 1.3.6.1.4.1.326.1.16.4.3.1.9
This object represents maximal numeric value allowed to be used as a VCI on any user connection over this FUNI service.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 32..63  

profileFuniIlmiSupport 1.3.6.1.4.1.326.1.16.4.3.1.10
This object specifies that an ILMI instance is to be supported on this FUNI service if the mode is set to enabled. This object corresponds to funiIfConfIlmiSupport in FUNI MIB.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

profileFuniSigSupport 1.3.6.1.4.1.326.1.16.4.3.1.11
This object specifies that a signalling instance is to be supported on this FUNI service if the mode is set to enabled. This object corresponds to funiIfConfSigSupport in FUNI MIB.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

profileFuniOamSupport 1.3.6.1.4.1.326.1.16.4.3.1.12
This object specifies that OAM cells and frames are to be transferred on this FUNI service if the mode is set to enabled. This object corresponds to funiIfConfOamSupport in FUNI MIB.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

profileFuniActiveVpiBits 1.3.6.1.4.1.326.1.16.4.3.1.13
The value of this object identifies the maximum number of active VPI bits configured for use at this FUNI interface. At the ATM FUNI, this value will be smaller than or equal to 4 and 8 when the FUNI header size is two and four bytes respectively, as specified by the profile attribute profileFuniConfMode. This object corresponds to atmInterfaceMaxActiveVpiBits in the ATOM MIB.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..8  

profileFuniActiveVciBits 1.3.6.1.4.1.326.1.16.4.3.1.14
The value of this object identifies the maximum number of active VCI bits configured for use at this FUNI interface. At the ATM FUNI, this value will be smaller than or equal to 6 and 16 when the FUNI header size is two and four bytes respectively, as specified by the profile attribute profileFuniConfMode. This object corresponds to atmInterfaceMaxActiveVciBits in the ATOM MIB.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..16  

profileFuniConfMode 1.3.6.1.4.1.326.1.16.4.3.1.15
The value of this object specifies whether a 2 or 4 byte header is present in each FUNI frame header over a FUNI service. For mode1a, mode1b and mode 3, a 2-byte header is used. For mode 4, a 4-byte header is used. This object corresponds to funiIfConfMode in FUNI MIB.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER mode1a(1), mode1b(2), mode3(3), mode4(4)  

profileFuniFcsBits 1.3.6.1.4.1.326.1.16.4.3.1.16
This object specifies whether a 16- or 32-bit FCS is used in each FUNI frame header over this FUNI logical interface.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER fcsBits16(1), fcsBits32(2)  

profileFuniHdrBytes 1.3.6.1.4.1.326.1.16.4.3.1.17
This object specifies whether a 2- or 4-bytes header is used in each FUNI frame header over this FUNI logical interface.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER hdrBytes2(1), hdrBytes4(2)  

profileFuniAal34Support 1.3.6.1.4.1.326.1.16.4.3.1.18
This object specifies whether support for AAL3/4 VCCs shall be allowed on this FUNI logical interface. A FUNI logical interface that cannot support AAL3/4 VCCs must only allow the value disabled(2).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

profileFuniRefCnt 1.3.6.1.4.1.326.1.16.4.3.1.19
The value of this object identifies the number of services that are referring to this profile.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

profileFrf8Table 1.3.6.1.4.1.326.1.16.4.4
The FRF.8 profile table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ProfileFrf8Entry

profileFrf8Entry 1.3.6.1.4.1.326.1.16.4.4.1
An entry in the FRF.8 profile table.
Status: current Access: not-accessible
OBJECT-TYPE    
  ProfileFrf8Entry  

profileFrf8Index 1.3.6.1.4.1.326.1.16.4.4.1.1
This object identifies the index of a profile in this table.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

profileFrf8RowStatus 1.3.6.1.4.1.326.1.16.4.4.1.2
This object is used to create new rows and delete existing rows in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

profileFrf8Name 1.3.6.1.4.1.326.1.16.4.4.1.3
This object specifies the symbolic name assigned to this profile for user reference.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

profileFrf8DeMode 1.3.6.1.4.1.326.1.16.4.4.1.4
If the DE mode is set to mapped, the DE field in the Q922 core frame is mapped to the ATM CLP filled of every cell generated by the segmentation process of the AAL5 PDU containing the information of that frame. Otherwise, the ATM CLP of every ATM cell generated by the segmentation process of the AAL5 PDU containing the information of that frame is set to a constant value specified by the configuration parameter profileFrf8DefaultClp.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER mapped(1), ignored(2)  

profileFrf8ClpMode 1.3.6.1.4.1.326.1.16.4.4.1.5
If the CLP mode is set to mapped, then the FR/ATM service interworking function will set the DE field of the Q922 core frame, provided that one or more cells belonging to this frame has its CLP field set. Otherwise, the DE field of the Q922 core frame is set to a constant value specified by the configuration parameter profileFrf8DefaultDe.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER mapped(1), ignored(2)  

profileFrf8FecnMode 1.3.6.1.4.1.326.1.16.4.4.1.6
If the Fecn mode is set to mapped, the FECN field in the Q922 core frame is mapped to the ATM EFCI field of every cell generated by the segmentation process of the AAL5 PDU containing the information of that frame. This mode provides congestion indication to the end-points where higher layer protocol entities might be involved in traffic control mechanisms. Otherwise, the EFCI field of cells generated by the segmentation process of the AAL5 PDU containing the information of the frame is always set to congestion-not-experienced.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER mapped(1), ignored(2)  

profileFrf8DefaultDe 1.3.6.1.4.1.326.1.16.4.4.1.7
This object represents the DE bit value of all generated FR frame headers if the CLP mode is set to ignored.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..1  

profileFrf8DefaultClp 1.3.6.1.4.1.326.1.16.4.4.1.8
This object represents the CLP bit value of all generated ATM cell headers if the DE mode is set to ignored.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..1  

profileFrf8Protocols 1.3.6.1.4.1.326.1.16.4.4.1.9
This object represents a binary map which lists all possible encapsulation translation protocols over this FRF.8 IWF instance. Any combination of the specified encapsulation modes will be supported. The binary map assignment is defined as below: ethernet (0000000000001) ethernetFcs (0000000000010) tokenRing (0000000000100) tokenRingFcs (0000000001000) ipRouted (0000000010000) arp (0000000100000) ipx (0000001000000) sna (0000010000000) fddi (0000100000000) fddiFcs (0001000000000) x.25/75 (0010000000000) 802.6 (0100000000000) routedIso (1000000000000) or any combinations of the binary map. The allowable range of the input is from 0 to 8191. This object corresponds to frf8ProtProtocol in fore-frf8 MIB.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..8191  

profileFrf8RefCnt 1.3.6.1.4.1.326.1.16.4.4.1.10
The value of this object identifies the number of connections that are currently referring to this profile.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

profileServiceTable 1.3.6.1.4.1.326.1.16.4.5
The generic service profile table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ProfileServiceEntry

profileServiceEntry 1.3.6.1.4.1.326.1.16.4.5.1
An entry in the generic service profile table.
Status: current Access: not-accessible
OBJECT-TYPE    
  ProfileServiceEntry  

profileServiceIndex 1.3.6.1.4.1.326.1.16.4.5.1.1
This object identifies the index of a profile in this table.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

profileServiceRowStatus 1.3.6.1.4.1.326.1.16.4.5.1.2
This object is used to create new rows and delete existing rows in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

profileServiceName 1.3.6.1.4.1.326.1.16.4.5.1.3
This object specifies the symbolic name assigned to this profile for user reference.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

profileServiceAccRate 1.3.6.1.4.1.326.1.16.4.5.1.4
This object represents the access rate of the service (kbps).
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

profileServiceMaxVccs 1.3.6.1.4.1.326.1.16.4.5.1.5
The maximum number of virtual circuits supported in this service. This object corresponds to frDlcmiMaxSupportedVCs in RFC1315 and funiIfExtConfVccs in fore-funi MIB.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

profileServiceMaxPayloadSize 1.3.6.1.4.1.326.1.16.4.5.1.6
This object represents the maximum payload size (bytes) supported by the service. This object corresponds to frPVCEndptInMaxFrameSize and frPVCEndptOutMaxFrameSize in RFC1604.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

profileServiceInBwOb 1.3.6.1.4.1.326.1.16.4.5.1.7
This object represents the bandwidth overbooking (percentage) of the service in the inbound direction. If the percentage is bigger than 100%, it is overbooking; otherwise it is underbooking.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..500  

profileServiceOutBwOb 1.3.6.1.4.1.326.1.16.4.5.1.8
This object represents the bandwidth overbooking (percentage) of the service in the outbound direction. If the percentage is bigger than 100%, it is overbooking; otherwise it is underbooking.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..500  

profileServiceRefCnt 1.3.6.1.4.1.326.1.16.4.5.1.9
The value of this object identifies the number of services that are currently referring to this profile.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

profileEpdPpdTable 1.3.6.1.4.1.326.1.16.4.6
The EPD/PPD profile table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ProfileEpdPpdEntry

profileEpdPpdEntry 1.3.6.1.4.1.326.1.16.4.6.1
An entry in the EPD/PPD profile table.
Status: current Access: not-accessible
OBJECT-TYPE    
  ProfileEpdPpdEntry  

profileEpdPpdIndex 1.3.6.1.4.1.326.1.16.4.6.1.1
This object identifies the index of a profile in this table.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

profileEpdPpdRowStatus 1.3.6.1.4.1.326.1.16.4.6.1.2
This object is used to create new rows and delete existing rows in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

profileEpdPpdName 1.3.6.1.4.1.326.1.16.4.6.1.3
This object specifies the symbolic name assigned to this profile for user reference.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

profileEpdPpdPriority 1.3.6.1.4.1.326.1.16.4.6.1.4
This object specifies the EPD/PPD priority queue the connection is assigned.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER low(1), high(2)  

profileEpdPpdClp0Epd 1.3.6.1.4.1.326.1.16.4.6.1.5
This object specifies whether the EPD/PPD controller discards CLP=0 traffic after the Clp0Epd threshold has been hit.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

profileEpdPpdClp1Ppd 1.3.6.1.4.1.326.1.16.4.6.1.6
This object specifies whether the EPD/PPD controller discards CLP=1 traffic after the Clp1Ppd threshold has been hit.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

profileEpdPpdClp1Epd 1.3.6.1.4.1.326.1.16.4.6.1.7
This object specifies whether the EPD/PPD controller discards CLP=1 traffic after the Clp1Epd threshold has been hit.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

profileEpdPpdRefCnt 1.3.6.1.4.1.326.1.16.4.6.1.8
The value of this object identifies the number of connections that are currently referring to this profile.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

profileFrf5Table 1.3.6.1.4.1.326.1.16.4.7
The FRF.5 profile table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ProfileFrf5Entry

profileFrf5Entry 1.3.6.1.4.1.326.1.16.4.7.1
An entry in the FRF.5 profile table.
Status: current Access: not-accessible
OBJECT-TYPE    
  ProfileFrf5Entry  

profileFrf5Index 1.3.6.1.4.1.326.1.16.4.7.1.1
This object identifies the index of a profile in this table. Indices 1 though 20 are reserved for system defaults
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

profileFrf5RowStatus 1.3.6.1.4.1.326.1.16.4.7.1.2
This object is used to create new rows and delete existing rows in this table.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

profileFrf5Name 1.3.6.1.4.1.326.1.16.4.7.1.3
This object specifies the symbolic name assigned to this profile for user reference.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

profileFrf5DeMode 1.3.6.1.4.1.326.1.16.4.7.1.4
If the DE mode is set to mapped, the DE field in the FR_SSCS frame is mapped to the ATM CLP filled of every cell generated by the segmentation process of the AAL5 PDU containing the information of that frame. Otherwise, if the DE mode is set to ignored, the ATM CLP of every ATM cell generated by the segmentation process of the AAL5 PDU containing the information of that frame is set to a constant value specified by the configuration parameter profileFrf5DefaultClp.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER mapped(1), ignored(2)  

profileFrf5ClpFrsscsDeMode 1.3.6.1.4.1.326.1.16.4.7.1.5
If the CLP mode is set to mapped, the FR/ATM network interworking function will set the DE field of the Q922 core frame, provided that one or more cells belonging to this frame has its CLP field set, or the DE bit of FR_SSCS frame is set. Otherwise, if the CLP mode is set to ignored, the DE bit of FR_SSCS frame is copied to the Q922 core frame.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER mapped(1), ignored(2)  

profileFrf5DefaultClp 1.3.6.1.4.1.326.1.16.4.7.1.6
This object represents the CLP bit value of all generated ATM cell headers if the DE mode is set to ignored.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..1  

profileFrf5MaxDlcis 1.3.6.1.4.1.326.1.16.4.7.1.7
The maximum number of virtual circuits supported in this VCC.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

profileFrf5MaxPayloadSize 1.3.6.1.4.1.326.1.16.4.7.1.8
This object represents the maximum payload size (bytes) supported by the VCC.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

profileFrf5RefCnt 1.3.6.1.4.1.326.1.16.4.7.1.9
The value of this object identifies the number of connections that are currently referring to this profile.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER